SVR-1630 Installation Guide

Transcription

Caution
This device is registered as an EMC for commercial purposes. Vendors and users should be aware of this
EMC registration. If this device is sold or purchased by mistake, the device will need to be altered for
domestic use.
FCC Compliance Statement
Caution : Any changes or modifications in the construction of this device which are not expressly
approved by the party responsible for compliance could void the user's authority to operate the
equipment.
NOTE : This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at their own expense.
Warning
This is a class A product. In a domestic environment this product may cause radio interference, in which
case the user may be required to take suitable correction measures
Warning
1. If the built-in Lithium battery is replaced by another type of battery, there is a risk of explosion.
Therefore it is necessary to replace the battery with the same type of battery or an identical one. In
addition, be sure to dispose of worn-out batteries properly because they may cause environmental
pollution.
2. Do not throw the battery into a fire, or heat , disassemble, cut or discharge it because those treatments
can cause the failure of device.
3. Do not recharge the remote controller’s battery.
Cautions
1. Do not put a large monitor or other heavy objects on the SVR-1630 when using it.
2. The SVR-1630 is designed for indoor use and therefore is not waterproof or dampproof. Therefore
before use it is necessary to fully understand the operating environment requirements detailed in the user
manual, and to use the device within the scope of the terms of service. For cleaning the device, wipe it
gently using a clean and dry cloth.
3. The SVR-1630 can be damaged by electric shock. Be careful to use AC power of 110V ~ 220V.
4. The SVR-1630 can be damaged by physical shock because it contains an HDD. Therefore, do not
throw or drop the device.
5. The SVR-1630 is made of metal. If it is thrown at anybody it may cause harm. Install the device in a
safe place out of the reach of children.
6. If the SVR-1630 does not operate correctly, do not disassemble it without authorization. Contact your
local agency for after sales service. The warranty will become invalid if it is disassembled without
authorization.
7. The SVR-1630 can transfer images in real time via a network and can be used for monitoring,
depending on the installation location. Therefore check the laws in the relevant area carefully, and then
install the device in such a way as not to infringe any of its laws.
SVR-1630
Contents
Contents
Executive Summary ................................................................................................................7
1.
Main Features of the SVR-1630......................................................................................7
2.
Component Check..........................................................................................................8
3.
Description of the Front/Rear View................................................................................10
Installation and Connection..................................................................................................12
4.
5.
6.
7.
8.
4
Basic Connection and Start-up......................................................................................12
4.1
Overall Layout .......................................................................................................12
4.2
Connecting a Camera............................................................................................13
4.3
Connecting a Monitor.............................................................................................14
4.3.1
Connecting a CCTV Monitor ...........................................................................14
4.3.2
Connecting a VGA Monitor..............................................................................14
4.4
Connecting Audio ..................................................................................................15
4.5
Supplying Power and Running ...............................................................................16
OSD Menu Configuration and Control ...........................................................................17
5.1
Menu Configuration ...............................................................................................17
5.2
Word Input.............................................................................................................18
Remote Controller Setup and Basic Control ..................................................................19
6.1
Setting ID of SVR-1630..........................................................................................19
6.2
Selecting SVR-1630 ..............................................................................................20
6.3
Operable Range of the Remote Controller .............................................................20
6.4
Loading batteries into the remote controller ..................................................20
SVR-1630 Installation Example.....................................................................................22
7.1
Basic Configuration................................................................................................22
7.2
Advanced Configuration.........................................................................................22
7.3
External Storage & Backup Configuration...............................................................23
7.4
Internet/Intranet Configuration................................................................................23
SVR-1630
Basic Setting .........................................................................................24
8.1
Viewing Images .....................................................................................................24
8.2
Setting Date and Time ...........................................................................................25
8.2.1
Time Zone ......................................................................................................25
8.2.2
Daylight Saving...............................................................................................25
8.2.3
Sync with NTP................................................................................................25
2004. 07. 2004 (v 1.0)
Samsung Techwin
Contents
8.2.4
Time Format ...................................................................................................26
8.2.5
Date Mode......................................................................................................26
8.2.6
Time ...............................................................................................................26
8.2.7
Apply Date/Time .............................................................................................26
8.3
9.
SVR-1630
Setting Recording Conditions.................................................................................26
8.3.1
Configuration Status .......................................................................................27
8.3.2
Channel Status ...............................................................................................27
8.3.3
Record Rate/Quality .......................................................................................28
8.3.4
Rate (fps)........................................................................................................28
8.3.5
Quality............................................................................................................28
8.3.6
Audio Record..................................................................................................28
8.3.7
Apply ..............................................................................................................28
Using Input/Output Terminals........................................................................................29
9.1
Connecting and Configuring the Sensor .................................................................30
9.1.1
Specification ...................................................................................................30
9.1.2
Connecting Sensor Input ................................................................................30
9.1.3
Setting Sensors ..............................................................................................31
9.2
Connecting and Setting Relay Output ....................................................................32
9.2.1
Specification ...................................................................................................32
9.2.2
Connecting to Relay Output Terminal ..............................................................32
9.2.3
Configuring Relay Out.....................................................................................33
9.3
Connecting and Configuring Serial Communication Ports.......................................34
9.3.1
Connecting Serial Communication Ports for Pan/Tilt/Zoom..............................34
9.3.2
Serial Communication Port Connection Layout................................................35
9.3.3
Serial Communication Port Figure...................................................................36
9.3.4
Configuring a Serial Port.................................................................................37
9.4
Connecting an External Device to a Serial Port ......................................................38
9.4.1
Connecting Text Input Devices (ATM / POS / Access Control) .........................38
9.4.2
Configuring Serial Setup (COM1)....................................................................39
9.4.3
Configuring Text..............................................................................................40
9.5
Connecting a USB Device......................................................................................41
9.6
Connecting Video In/Out ........................................................................................42
10.
HDD..........................................................................................................................43
10.1
Adding and Replacing HDDs on the HDD Rack......................................................43
10.1.1
Available HDDs ..............................................................................................43
10.1.2
Mounting an HDD ...........................................................................................43
Samsung Techwin
2004. 07. 2001 (v 1.0)
5
SVR-1630
10.2
Contents
Adding and Replacing External Storage Device......................................................46
10.2.1
IEEE1394 Port................................................................................................46
10.2.2
Connecting IEEE1394 Device.........................................................................46
10.3
11.
Registering and Formatting an HDD.......................................................................47
Remote Monitoring and Control.................................................................................48
11.1
Connecting via Ethernet.........................................................................................48
11.2
Configuring an SVR-1630 Network ........................................................................49
12.
Using the SVR Manager............................................................................................50
12.1
PC System Requirements for running the SVR Manager........................................50
12.2
Installing the SVR Manager ...................................................................................50
12.3
Uninstalling the SVR Manager ...............................................................................52
12.4
Configstation .........................................................................................................52
12.5
Monitor ..................................................................................................................53
12.6
Playback................................................................................................................54
Appendix ...............................................................................................................................55
1.
HDD .............................................................................................................................56
1.1
Fundamental Notions & Terms ...............................................................................56
1.1.1
SVR-1630 Storing Structure (VFS2) ............................................................56
1.1.2
Backup ...........................................................................................................56
1.1.3
Disk Manager .................................................................................................57
1.2
Replacing HDDs ....................................................................................................58
1.2.1
Checking HDDs ..............................................................................................58
1.2.2
When the primary disk fails .............................................................................58
1.2.3
When an auxiliary disk fails.............................................................................58
1.3
Keeping Data.........................................................................................................59
1.3.1
Backup ...........................................................................................................59
1.3.2
Separating and Preserving HDDs ...................................................................60
1.3.3
Cautions .........................................................................................................60
2.
Changing Video Type....................................................................................................61
3.
Using CD-Rom .............................................................................................................62
4.
6
3.1
CD- ROM DISC Components.................................................................................62
3.2
Preparation............................................................................................................62
3.3
Reading the User Manual in CD-ROM ...................................................................62
Specification .................................................................................................................63
2004. 07. 2004 (v 1.0)
Samsung Techwin
오류! 스타일이 정의되어 있지 않습니다.
SVR-1630
Executive Summary
1. Main Features of the SVR-1630
The SVR-1630 is a new concept DVR, saving the video inputs, audio, text data and alarm data of 16
channels in two built-in HDDs, with its main features described below.
□ 16-Channel Video Input Support
□ 1 Channel Audio Recording and Playback
□ Max. 240fps Recording
□ Real-time monitoring (30fps per channel)
□ Built-in software multiplexer for 16-Channel split monitoring
(1 / 2x2/3x3 /4x4 Screen Mode Support)
□ Up to 4TB Storage Capacity (Expansion using IEEE 1394 Port)
□ Text data recording by interlocking with ATM/POS devices
□ 16 Sensor Inputs and 4 Interlocked Relay Outputs
□ Hardware Motion Detection (64 Section)
□ Backup using IEEE1394 and Network
□ PTZ control
□ Easy-to-use Color Graphic OSD
□ Dynamic IP support
□ IR Remote Controller
□ Remote Management Software provided (SVR Manager)
□ Dual CCTV Monitor support (3 Normal, 1 Spot)
□ VGA monitor support
□ CD-RW backup support (option)
Samsung Techwin
2004. 07. 2001 (v 1.0)
7
SVR-1630
2. Component Check
Please check the package to make sure that you receive all the accessories, including the components shown below.
1. SVR-1630 (1EA)
2. AC Power Cord (1EA)
3. CD-ROM (Including SVR Manager) (1EA)
4. Remote Controller (1EA)
5. Guide (2EA)
6. HDD Fixing KIT (1SET)
7. 19” RACK FIXING KIT (1SET)
8. HDD EARTH CABLE (1EA)
8
2004. 07. 2004 (v 1.0)
Samsung Techwin
SVR-1630
9. HDD Removable Rack KIT(1SET)
Samsung Techwin
2004. 07. 2001 (v 1.0)
9
SVR-1630
3. Description of the Front/Rear View
SVR-1630 Front View
(1) Power Switch
(2) HDD Removable Rack
(3) Function Buttons
(4) Channel Buttons
(5) Status LED
(6) Jog Shuttle for Search and Playback
(7) Function Switch
(8) Play and Search Button
(9) Search/Preset Switch
(10) Remote Controller Receiver
(11) USB Connector
(12) IEEE 1394 Connector
(13) Bracket fixing hole for rack mount
10
2004. 07. 2004 (v 1.0)
Samsung Techwin
SVR-1630
SVR-1630 Rear View
(14) BNC connector for video output
(15) BNC connector for video input
(16) BNC connector for Monitor A output
(17) BNC connector for Monitor A input
(18) Ethernet connector
(19) GND
(20) Input/output terminal for RS232 & RS422/485
(21) IEEE 1394 connector
(22) S-VHS connector for Monitor A output
(23) Input/output terminals for sensor, relay and serial
(24) RS232 connector (9Pin D-Sub)
(25) Connector for VGA monitor
(26) RCA connector for audio input/output
(27) AC power input connector
Samsung Techwin
2004. 07. 2001 (v 1.0)
11
SVR-1630
Installation and Connection
4. Basic Connection and Start-up
4.1 Overall Layout
(1) The devices that can be connected to the SVR-1630 are described below. See each relevant section in
the installation manual for the contents on the figure.
12
2004. 07. 2004 (v 1.0)
Samsung Techwin
SVR-1630
4.2 Connecting a Camera
(1) Connect a camera to the SVR-1630 using the coaxial cable as shown in the figure below.
<Note>
1. The input video type should be either NTSC or PAL. Do not use both types at the same time.
2. Automatic setting of 75Ω terminal resistance
Two video terminals are internally connected. A terminal resistance of 75Ω exists when
only one terminal is connected. Hi-z exists when both terminals are connected.
See “9.6. Connecting Video In/Out ” on the page 42.
3. The Input Video Type (NTSC/PAL) is automatically recognized when the device runs.
For the recognition sequence, camera number 1 is recognized first, and then the sequence is decided
according to the camera signal type that is first detected, from cameras no. 1 to 16. When no cameras
are connected, the internal jumper setting is applied. To change the internal jumper, see page 61,
Appendix “2. Changing Video Type”
Samsung Techwin
2004. 07. 2001 (v 1.0)
13
SVR-1630
4.3 Connecting a Monitor
4.3.1 Connecting a CCTV Monitor
(1) Connect a monitor to the SVR-1630 using the coaxial cable as shown in the figure below.
4.3.2 Connecting a VGA Monitor
(1) Monitor Outuput A can output to VGA. For better definition quality, connect Monitor A to the VGA
Monitor as shown in the figure below.
<Note>
1. The SVR-1630 monitor outputs are divided into A (Normal) and B (Spot). If only one monitor is
connected, connect Monitor A.
2. For Monitor Output A, the same video output is transferred to two BNC connectors and an S-VHS
connector.
14
2004. 07. 2004 (v 1.0)
Samsung Techwin
SVR-1630
4.4 Connecting Audio
(1) Connect an audio signal to the SVR-1630 using the RCA cable as shown in the figure below.
Samsung Techwin
2004. 07. 2001 (v 1.0)
15
SVR-1630
4.5 Supplying Power and Running
(1) Connect the power cable as shown in the figure below.
<Note>
1. Connect the power cable, press the power switch, and the device starts booting.
2.Press and release the power switch while SVR-1630 is ON, the following windows are displayed
according to the system setting after 4 seconds.
When there is Admin password in “System Setup”
The dialogue box asking to enter the admin password is appeared. Enter the password, and the power is
off.
When there is no Admin password in “System Setup”
The dialogue box asking “Yes” or “No” is appeared. Select “Yes”, and the power is off.
3. For turning the power on again, press the power switch.
16
2004. 07. 2004 (v 1.0)
Samsung Techwin
SVR-1630
5. OSD Menu Configuration and Control
5.1 Menu Configuration
Press the [MENU] button on the keypad on the front panel, and the system changes to the SVR-1630
Setup mode. The OSD Menu is displayed as shown in the figure below. The Jog/Shuttle on the menu is
controlled as described in the figure below.
① Main Menu
② Sub-menu
③ Setup Dialogue Box
Samsung Techwin
2004. 07. 2001 (v 1.0)
17
SVR-1630
(1) Main Menu : The selected tab is shown in blue and the related sub-menus will be shown below the tab.
To move to the previous/next Main Menu Tab, use the [◀/▶] arrow buttons. To move to the relevant submenu, press the [ENTER] or [▼] buttons.
(2) Sub-menu : The selected sub-menu is shown in blue and the related setting page will be shown to the
right of the sub-menu. Use the [▲/▼] arrow buttons to move within the sub-menu list. To move to the setting
page, press the [ENTER] button. To go to the Main Menu, press the [ESC] button.
(3) Setting Page : The selected item is shown with a circle to the left of its name. The field to set values is
shown in gray. To move within each page, use the [◀/▶] or [▲/▼] arrow buttons. Press the [ENTER] button
to change the value of a setting. The setting values of items are divided into text (including letters and
numbers) and numbers. When the setting value is a word, a dialogue box to edit the word will open. When the
setting value is a number, it should be set by using the [◀/▶] or [▲/▼] arrow buttons. After the value is set,
press the [ESC] button. To go to the Main Menu, press the [ESC] button.
5.2 Word Input
Select a value using the [▲/▼] buttons. Press the [ENTER] button to confirm the selected value.
18
2004. 07. 2004 (v 1.0)
Samsung Techwin
SVR-1630
6. Remote Controller Setup and Basic Control
6.1 Setting ID of SVR-1630
When controlling several SVR-1630s with one remote controller, multiple DVRs can be set by one remote
controller. Set the remote controller ID as described below.
(1) Press the [MENU] button.
(2) Select “System” by using the [▶] button and press the [ENTER] or [▼] button.
(3) Select “Etc.” using the [▼] button and press the [ENTER] button.
(4) Select “Remote Control ID,” and press the [ENTER] button.
(5) Select a value using the [◀/▶] buttons and press the [ESC] button.
(6) Press the [ESC] button to return to Monitor mode.
Samsung Techwin
2004. 07. 2001 (v 1.0)
19
SVR-1630
6.2 Selecting SVR-1630
Multiple DVRs with different IDs can be controlled by one remote controller. To select a specific SVR-1630,
press the ID button of the remote controller. When the DVR ID matches the remote controller ID, the LED on
the front of the SVR-1630 lights up and a buzzer sounds for two seconds.
<Note>
Up to 16 Remote Controller IDs are supported, which consist of two digits from 1 to 4.
ID
Key Sets
ID
Key Sets
ID
Key Sets
ID
Key Sets
ID1-1
1,1
ID2-1
2,1
ID3-1
3,1
ID4-1
4,1
ID1-2
1,2
ID2-2
2,2
ID3-2
3,2
ID4-2
4,2
ID1-3
1,3
ID2-3
2,3
ID3-3
3,3
ID4-3
4,3
ID1-4
1,4
ID2-4
2,4
ID3-4
3,4
ID4-4
4,4
6.3 Operable Range of the Remote Controller
6.4 Loading batteries into the remote controller
The remote controller uses only AAA-type batteries. The batteries are loaded into the remote controller as
described below.
1. Remove the battery cover.
2. Check battery polarity and insert batteries.
20
2004. 07. 2004 (v 1.0)
Samsung Techwin
SVR-1630
3. Replace the battery cover.
Samsung Techwin
2004. 07. 2001 (v 1.0)
21
SVR-1630
7. SVR-1630 Installation Example
7.1 Basic Configuration
7.2 Advanced Configuration
22
2004. 07. 2004 (v 1.0)
Samsung Techwin
SVR-1630
7.3 External Storage & Backup Configuration
7.4 Internet/Intranet Configuration
Samsung Techwin
2004. 07. 2001 (v 1.0)
23
SVR-1630
8. SVR-1630 Basic Setting
8.1 Viewing Images
After initial start-up, images are displayed in a split screen corresponding to the number of channels connected
to the monitor.
<Note>
If the user password is set, a prompt for entering the password will appear. The keypad on the front panel
won’t work. (A user password is not set in the factory)
24
2004. 07. 2004 (v 1.0)
Samsung Techwin
SVR-1630
8.2 Setting Date and Time
(1) Press the [MENU] button, and select the “Quick Setup” tab on the OSD Menu.
(2) Select “Date/Time” using the [ENTER] or [▼] button and press [ENTER].
8.2.1 Time Zone
(1) Select “Time Zone” using the [◀/▶] or [▲/▼] arrow buttons and press the [ENTER] button.
(2) Select a value using the [◀/▶] buttons and press the [ESC] button when finished.
8.2.2 Daylight Saving
(1) “Daylight Saving Time” is only activated when the time zone is selected.
(2) Select “Daylight Saving” using the [◀/▶] or [▲/▼] arrow buttons and press the [ENTER] button.
(3) Select “Yes/No” using the [◀/▶] buttons and press the [ESC] button.
8.2.3 Sync with NTP
In order to synchronize time with the NTP (Network Time Protocol) server, select “On”.
(1) Select “Sync with NTP” using the [◀/▶] or the [▲/▼] buttons and press the [ENTER] button.
(2) Select “On/Off” using the [◀/▶] buttons and press the [ESC] button.
Samsung Techwin
2004. 07. 2001 (v 1.0)
25
SVR-1630
8.2.4 Time Format
(1) Select “Time Format” using the [◀/▶] or [▲/▼] buttons and press [ENTER].
(2) Two Time Formats are available; ‘MM/DD/YYYY’ ,‘YYYY/MM/DD’ ‘DD/MM/YYYY’. Select a value
using the [▲/▼] buttons, and press the [ESC] button when finished. (Default value is ‘MM/DD/YYYY’.)
8.2.5 Date Mode
(1) Select “Date Mode” using the [◀/▶] or [▲/▼] buttons and press [ENTER].
(2) Select ‘MM’/‘DD’/‘YYYY’ using the [◀/▶]buttons, and select the value using the [▲/▼] buttons.
(3) Press the [ESC] button when finished.
8.2.6 Time
(1) Select “Time” using the [◀/▶] or [▲/▼] buttons and press [ENTER].
(2) Select ‘HH’/‘MM’ using the [◀/▶] buttons, and select the value using the [▲/▼] buttons.
(3) Press the [ESC] button when finished.
8.2.7 Apply Date/Time
Most setting values are applied automatically when exiting from the related menu page. But “Date”&
“Time” settings are not applied automatically because they may critically affect the file system of the
recorded HDD. To apply Date/Time settings, confirm the settings with the [Apply Date/Time] button.
(1) Select “Apply Date/time” using the [◀/▶] or [▲/▼] buttons and press [ENTER]. A warning message will
appear.
Select “Yes” using the [◀/▶] or [▲/▼] buttons and press [ENTER]. To cancel, press the [ESC] button.
8.3 Setting Recording Conditions
Recording conditions under the “Quick Setup” menu tab apply the same values to all 1~16analog channels. All
settings are applied for 24 hours/day regardless of the values set for “Time Schedule” or “Alarm Rec.”
26
2004. 07. 2004 (v 1.0)
Samsung Techwin
SVR-1630
(1) Press the [MENU] button, and select “Quick Setup.”
(2) Move to a sub-menu by pressing [ENTER] or the [▼] button.
(3) Select “Recording” using the [▲/▼] buttons and press the [ENTER] button.
8.3.1 Configuration Status
Displays the recording configuration status. Indicates where the final setting is done. When setting up through
the “Quick Setup” menu, “Macro Setup” will be shown. When setting up through “Schedule Rec.” or “Event
Rec.,” “Custom Setup” will be shown.
<Note>
“Macro Setup” is only shown when the schedule recording conditions for all 16 channels are the same.
8.3.2 Channel Status
(1) Select “Channel Status” using the [▲/▼] buttons and press the [ENTER] button.
(2) Select a value using the [◀/▶] buttons. Press the [ESC] button when finished.
Samsung Techwin
2004. 07. 2001 (v 1.0)
27
SVR-1630
8.3.3 Record Rate/Quality
(1) Select “Recording Speed/Quality” using the [▲/▼] buttons and press the [ENTER] button.
<Note> Record Rate/Quality means
Low : Rate=1fps and Quality=Q5
Std. : Rate=5fps and Quality=Q5
High : Rate=15fps and Quality=Q5
Customer : Rate and Quality = Manually defined by User.
8.3.4 Rate (fps)
When “Recording Speed/Quality” is set as “Customer,” values can be set manually.
(1) Select “Speed” using the [▲/▼] buttons and press the [ENTER] button.
8.3.5 Quality
When “Recording Speed/Quality” is set as “Customer,” values can be set manually.
(1) Select “Quality” using the [▲/▼] buttons and press the [ENTER] button.
8.3.6 Audio Record
(1) Select “Audio Record” using the [▲/▼] buttons and press the [ENTER] button.
8.3.7 Apply
(1) Select “Apply” using the [▲/▼] buttons and press the [ENTER] button.
(2) Setting values are applied and the previous menu will be displayed.
28
2004. 07. 2004 (v 1.0)
Samsung Techwin
SVR-1630
9. Using Input/Output Terminals
<Note> Wiring
Terminating Wires
The wires for the TERMINAL BLOCK are terminated as described below. When solid and stranded
wires are used, be careful because the thickness of usable wires varies.
Stranded Wire: Strip the outer covering to the
defined length (8~10mm) and solder it.
Suitable wires are AWG 22 ~ 26.
Solid Wire: Strip the outer covering to the
defined
length
(8~10mm).
Suitable
wires are AWG 20 ~ 26.
Inserting/removing wires
For inserting into or removing wires from the
TERMINAL BLOCK, push the lever as shown in
the figure.
Samsung Techwin
2004. 07. 2001 (v 1.0)
29
SVR-1630
9.1 Connecting and Configuring the Sensor
9.1.1 Specification
The sensor input of the SVR-1630 has the specifications and normal operating conditions as described
below.
Specification
No. of Input Circuits
16 Photocoupler Inputs
Input Type
N.C, N.O supported
Sensor
Dry Contact Sensor
Connection
Connect the stripped wires to the Terminal Block.
Valid
Electrical
Performance
Input
Pulse Minimum 500ms
Duration
Output Currents
Typical DC 12mA
9.1.2 Connecting Sensor Input
For connection of sensor inputs S1 ~ S16, see the figure below. The figure below is an example of dry
contact sensor connection. For connecting or removing wires, see “Preparing and Connecting Wires” on
page 29. For connecting sensors (Open Collector output, etc.) other than dry contact sensors, it is
necessary to contact the Samsung Techwin CS team.
30
2004. 07. 2004 (v 1.0)
Samsung Techwin
SVR-1630
9.1.3 Setting Sensors
(1) Press the [MENU] button, and the OSD Configuration menu appears. Select “Event Source”.
(2) Go to the Sub-menu using the [ENTER] or [▼] buttons. Select “Sensor” and press the [Enter] button
9.1.3.1
All Ch
Used for setting 16 sensors at the same time. Set the Off, or Normal Open (N.O.) / Normal Close (N.C.)
type.
(1) Select ‘All Ch’ and set the type.
(2) Press the “Apply” button to confirm the setting.
9.1.3.2
Configuration
Used for individually setting 16 sensors. Select and set each sensor.
(1) Select “Configuration” and press the [Enter] button.
(2) Select the sensor (S1~S16) to set and set the type.
(3) After setting, press the [ESC] key to return to the ODS menu.
<Note>
1. Sensor setting is for deciding whether to use sensors, and the sensor type. Storing according to sensor
inputs and relay should be set separately.
2. See “Event Rec.” of the “SVR-1630 User Manual” for storing and “Event Act” for relay output.
Samsung Techwin
2004. 07. 2001 (v 1.0)
31
SVR-1630
9.2 Connecting and Setting Relay Output
9.2.1 Specification
The alarm output of the SVR-1630 has the specifications and normal operating conditions as described
below.
Spec.
No. of Output Circuits
Automatic output of 4 Relays
Output Method
Dry Contact
Connection
Connect the stripped wires to the Terminal Block.
DC
24V DC, 1.25A, 30W
125V DC, 0.24A, 30W
Rated
Values
AC
125V AC, 0.5A, 62.5VA
250V AC, 0.25A, 62.5VA
9.2.2 Connecting to Relay Output Terminal
For connection of R1 ~ R4 outputs, see the figure below. The figure below is an example for connecting
the warning lamp. For connecting or removing wires, see “Wiring” on page 28.
32
2004. 07. 2004 (v 1.0)
Samsung Techwin
SVR-1630
9.2.3 Configuring Relay Out
Each relay can be synchronized with a sensor input or with motion detection, and its operation condition can be
set differently according to the schedule. Relays can also be controlled locally by pressing the [RELAY] button
followed by the relay number. Relays can also be controlled remotely through the “SVR Manager software.”
<Note>
See the “SVR-1630 User Manual” for setting details.
Samsung Techwin
2004. 07. 2001 (v 1.0)
33
SVR-1630
9.3 Connecting and Configuring Serial Communication Ports
9.3.1 Connecting Serial Communication Ports for Pan/Tilt/Zoom
PTZ devices can only be connected and controlled provided that the SVR-1630 supports a through COM port.
Check the models available in the SVR-1630OSD Menu. The figure below is an example for connecting an
RS485 (COM2) communication terminal to a PTZ camera. Connect other serial communication ports to other
devices by referring to the connection layout in the figure below. For connecting or removing wires, see
“Preparing and Connecting Wires” on page 29.
34
2004. 07. 2004 (v 1.0)
Samsung Techwin
SVR-1630
9.3.2 Serial Communication Port Connection Layout
9.3.2.1
COM1 Connection Layout
9.3.2.2
9.3.2.3
Samsung Techwin
2004. 07. 2001 (v 1.0)
35
SVR-1630
9.3.2.4
9.3.3 Serial Communication Port Figure
9.3.3.1
COM1 Figure
9.3.3.2
COM3/COM/4 Figure
36
2004. 07. 2004 (v 1.0)
Samsung Techwin
9.3.4
SVR-1630
Configuring a Serial Port
Configure the COM port for PTZ and available models in the SVR-1630 “System / Serial Setup” .
After completing the serial setup, configure the base address or port for each channel under the “Camera” menu
tab. When connecting PTZ devices to several cameras, be sure of the base address setting.
Samsung Techwin
2004. 07. 2001 (v 1.0)
37
SVR-1630
9.4 Connecting an External Device to a Serial Port
9.4.1 Connecting Text Input Devices (ATM / POS / Access Control)
In addition to images, the SVR-1630 can record text data received from a POS/ATM through the RS232 serial
port (COM1).
Connect RS232 (COM1) by referring to the “9.3.3.1. COM1 Figure” on page 36. Set the text data in the “Event
Source” menu and Serial data in the SVR-1630 “System” menu.
38
2004. 07. 2004 (v 1.0)
Samsung Techwin
SVR-1630
9.4.2 Configuring Serial Setup (COM1)
(1) Select “System” from the OSD Menu and go to the Sub-menu.
(2) Select COM1 RS232 in “Serial Setup” and set the Device to “Text”.
(3) Set the Baud Rate/Parity/Stop bit/Data bits to the same values as the input device.
Samsung Techwin
2004. 07. 2001 (v 1.0)
39
SVR-1630
9.4.3 Configuring Text
(1) Select “Event Source” from the OSD Menu and go to the sub-menu.
(2) Select “Text” and set the text related data.
<Note>
Some external devices may not be recognized, depending on their characteristics. Before installing any
external device, consult your local vendor.
40
2004. 07. 2004 (v 1.0)
Samsung Techwin
SVR-1630
9.5 Connecting a USB Device
A USB port generally uses a USB memtory for a simple video copy. For connecting a USB device, its rated
values shall not exceed the specification defined below.
USB Spec.
Available Devices
Output
Voltage/Current
Ver 1.1 (Max 12M bps)
USB Memory
DC 5V / Max. 200mA
<Note>
The disk should be formatted to the FAT32 type.
If properly connected, the disk is recognized automatically as in the following picture. To copy images,
the process is as follows: Set copy range (up to 1 minute) Æ Select Disk Æ Copy (press “Start”).
Copy Images
Time
5 sec
Select
Disk
1 Disk(s)
Type
Model
Size (KB)
[F] Ext
Sony Flash Memory
6640
Start
Samsung Techwin
2004. 07. 2001 (v 1.0)
41
SVR-1630
<Note>
1. Note that USB Memory products that require a Windows program to operate may not be recognized by
the SVR-1630.
2. See the “SVR-1630 User’s Manual” for details about Copy functions.
9.6 Connecting Video In/Out
For the SVR-1630, the loop through Video In and Out automatically detects the connection status and sets
the terminal resistance.
For example, if only Video In is connected, the terminal resistance is internally set to 75Ω. If both Video
In and Out are connected, the terminal resistance is changed to Hi-z. Therefore, for connecting both Video
In and Out, the terminal resistance receiving the signal should be set to 75Ω.
42
2004. 07. 2004 (v 1.0)
Samsung Techwin
SVR-1630
10. HDD
10.1 Adding and Replacing HDDs on the HDD Rack
10.1.1 Available HDDs
It is recommended to use the following HDD models with the SVR-1630. If a non-recommended HDD is used,
Samsung Techwin’s warranty will not cover any failures.
Maker : MAXTOR
Series
Model No.
Capacity
6Y120L(P)0
120GB
6Y250P0
250GB
DiamondMax Plus 9 (7200rpm)
<Note>
The buffer for DiamondMax Plus 9’s model “L” is 2MB; for model “P” the buffer is 8MB.
10.1.2 Mounting an HDD
(1) Check if the HDD is currently set as “Master”.
(2) Turn off the SVR-1630’s power.
Samsung Techwin
2004. 07. 2001 (v 1.0)
43
SVR-1630
(3) Unlock the rack by turning the key anti-clockwise.
(4) Pull the handle of the HDD RACK to completely remove the rack from the SVR-1630 main unit.
(5) Remove the cover by pulling the hook on the cover as shown in the figure below.
44
2004. 07. 2004 (v 1.0)
Samsung Techwin
SVR-1630
(6) Connect the connector inside the rack to the HDD. Fix the HDD using the screws included in the
package’s accessories and close the cover. (Fix the HDD with care, avoiding giving it any knocks.)
(7) Drop the handle and push the rack until it reaches the back of the SVR-1630’s main unit.
(8) Lock the rack using a key.
Samsung Techwin
2004. 07. 2001 (v 1.0)
45
SVR-1630
10.2 Adding and Replacing External Storage Device
10.2.1 IEEE1394 Port
The SVR-1630 used IEEE1394 for the external storage device interface. It has two IEEE1394 ports, one
each on the front and rear panel. With them the SVR-1630 can expand storage capacity up to 4TB.
<Note>
Some IEEE1394 bays may not be recognized by the SVR-1630. Before purchasing, consult your local
vendor to confirm compatibility.
10.2.2 Connecting IEEE1394 Device
When using a FireWire supported external HDD, hard drive bays can be connected to a port in the front panel
or a port in the rear panel. The SVR-1630 does not supply power to the hard drive bay; therefore only bays that
use external power can be used.
<Note>
When an external HDD is connected while the SVR-1630 is running, the SVR-1630 should correctly
detect the external HDD. If it doesn’t, it is recommended to try connection as follows.
1. Power off the SVR-1630 and external HDD.
2. Connect the external HDD to the IEEE1394 port.
3. Power on the external device.
4. Power on the SVR-1630
46
2004. 07. 2004 (v 1.0)
Samsung Techwin
SVR-1630
10.3 Registering and Formatting an HDD
The “Disk Manager” will automatically run on start-up after installing a HDD.
If the “Disk Manager” doesn’t run automatically on start-up, make sure the HDD is properly installed.
(1) Press the [ENTER] button at “Select Disk”.
(2) Select the newly-added HDD (indicated as “[F]”) using the [▲/▼] buttons and press the [ESC] button
(3) Select “Action” using the [▲/▼] buttons and press the [ESC] button.
(4) Select “Add” using the [◀/▶] buttons and press the [ESC] button.
(5) Select “Apply” using the [▲/▼] buttons and press the [ESC] button. The HDD status is changed to “[*]”.
And the new HDD is successfully registered.
(6) Select “Action” using the [▲/▼] buttons and press the [ESC] button.
(7) Select “Format” using the [◀/▶] buttons and press the [ESC] button.
(8) Select “Apply” using the [▲/▼] buttons and press the [ESC] button. The HDD status is changed to “[R]”
after formatting.
(9) Shut down the “Disk Manager” by pressing the [ESC] button.
Samsung Techwin
2004. 07. 2001 (v 1.0)
47
SVR-1630
11. Remote Monitoring and Control
The SVR-1630 can be accessed using a remote PC via the Internet/Intranet. As with the local site, the SVR1630 can be controlled and monitored from remote sites via the Internet/Intranet.
11.1 Connecting via Ethernet
(1) Turn off the SVR-1630’s power switch.
(2) Connect the SVR-1630 to the hub with an Ethernet cable.
(3) Turn on the SVR-1630’s power switch.
<Note>
1. Supply power to the SVR-1630 only after connecting the Ethernet cable, to avoid electrical damage to the
SVR-1630.
2. Firmly connect the Ethernet cable by fully pushing it into the hub.
3. Check the LED on the SVR-1630’s rear panel after supplying power.
48
2004. 07. 2004 (v 1.0)
Samsung Techwin
SVR-1630
11.2 Configuring an SVR-1630 Network
The following description is on based on Ethernet connection. For more detailed information on the Network
Settings Page and when xDSL is used, please refer to the “SVR-1630 User Manual”
(1) Press the [MENU] button.
(2) Select “System” using the [◀/▶] buttons and press [ENTER].
(3) Select “Network” using the [▲/▼] buttons and press [ENTER].
(4) Select “IP Addr” using the [▲/▼] buttons and press [ENTER].
(5) Press the [ESC] button after entering the IP address in the dialogue box.
(6) Select “Net Mask” using the [▲/▼] buttons and press [ENTER].
(7) Press the [ESC] button after entering the Net Mask in the dialogue box.
(8) Select “Gateway” using the [▲/▼] buttons and press [ENTER].
(9) Press the [ESC] button after entering the Gateway in the dialogue box.
(10) Select “DNS” using the [▲/▼] buttons and press [ENTER].
(11) Press the [ESC] button after entering the DNS in the dialogue box.
(12) Press the [ESC] button until the Monitor Mode appears.
Samsung Techwin
2004. 07. 2001 (v 1.0)
49
SVR-1630
12. Using the SVR Manager
12.1 PC System Requirements for running the SVR Manager
Minimum Requirements
Recommended Requirements
CPU
P-Ⅲ 600MHz or above
P-Ⅲ 1GHz or above
RAM
128 MB or above
256 MB or above
VGA
16 MB or above
32 MB or above
OS
Windows 2000/XP
Windows 2000/XP
Resolution
1024 X 768 pixels or above
1024 X 768 pixels or above
Network
100 Base TX Fast Ethernet
100 Base TX Fast Ethernet
12.2 Installing the SVR Manager
(1) Insert the Setup CD-ROM into the CD-ROM drive of the administrator’s PC
(2) Double click the SVR Manager setup file. The Install Shield Wizard will be automatically installed.
(3) Click the “I Agree” button to accept the license agreement
50
2004. 07. 2004 (v 1.0)
Samsung Techwin
SVR-1630
(1) Press the “Next” button.
(2) Browse and choose a directory if the default directory is not preferred. Click the “Install” button,
after selecting a directory to install into.
(3) Click the “Close” button after the SVR Manager program is installed successfully.
Samsung Techwin
2004. 07. 2001 (v 1.0)
51
SVR-1630
12.3 Uninstalling the SVR Manager
(1) Click the Windows “Start” Button.
(2) Select and Click the ‘Uninstall’ icon to run the Uninstall Shield.
(3) Uninstall the program according to the instructions in the window.
12.4 Configstation
Click the icon on the desktop to run the “SVR Manager Configstation” program.
52
2004. 07. 2004 (v 1.0)
Samsung Techwin
SVR-1630
12.5 Monitor
Click the related icon and run the “SVR Manager Monitor” program.
Samsung Techwin
2004. 07. 2001 (v 1.0)
53
SVR-1630
12.6 Playback
Click the related icon and run the “SVR Manager Playback” program.
54
2004. 07. 2004 (v 1.0)
Samsung Techwin
SVR-1630
Appendix
Samsung Techwin
2004. 07. 2001 (v 1.0)
55
SVR-1630
1. HDD
1.1 Fundamental Notions & Terms
1.1.1 SVR-1630 Storing Structure (VFS2)
Samsung Techwin has developed a unique storage system suitable for SVR and has applied it to the SVR1630. The basic features are described below.
(1) It is theoretically possible to connect 3 physical HDDs internally (Internal, ATA Interface) and 24 HDDs
externally (External: 2 IEEE1394 ports). The total number of HDDs that can be connected internally and
externally is 24.
(2) All of the connected HDDs are recognized as one virtual disk, and the SVR-1630 supports up to 4TB.
(3) The HDD that is firstly connected becomes the primary disk and other HDDs are classified to auxiliary
disks.
<Note>
ATA (or EIDE) supports two channel interfaces (Primary/Secondary). Each channel can be connected to two
devices (Master/Slave, HDD/CD-ROM). The Primary Interface connects a total of two HDDs and the
Secondary Interface connects the HDD Rack and CD-RW. In order to prevent confusion with the VFS2’s
Primary Disk, we will not use the terms Primary/Secondary.
(4) Each disk is composed of a Log Partition and a Schedule Partition.
<Note>
Log Partition
To store recorded data information
Schedule Partition
To store images recorded according to the storing schedule
1.1.2 Backup
(1) Backup is possible only through an IEEE1394 port, and the HDD for backup should be formatted to the
FAT32 type. (The type is indicated as [F] in the Disk Manager.)
56
2004. 07. 2004 (v 1.0)
Samsung Techwin
SVR-1630
1.1.3 Disk Manager
(1) When an HDD is added or deleted physically, the Disk Manager runs automatically after rebooting. If it
doesn’t, you can run “MenuÆDiskÆDisk Manager” from the console.
(2) HDD Type
[R]
Available for recording depending on successful formatting of the HDD
[V]
Connected and formatted as a DVR file system. If using the ‘Add used’ command, it will be
changed to [R]. There is no need to reformat.
[F]
Connected, but not available, file system. After using ‘Add’, you need to format to make it
like [R]. Otherwise indicates the FAT 32 file system connected for backup.
[C]
Built-in or external CD-Recorder
[X]
The HDD cable is not connected or has some problem. In this case, the HDD should be
removed using the ‘Confirm Removed’ menu.
IntA
Internal Primary HDD
IntB
Internal Auxiliary HDD
R-HDD
HDD in the built-in hard disk rack
Ext
External HDD listing order can be changed according to the recognition
sequence.
Samsung Techwin
2004. 07. 2001 (v 1.0)
57
SVR-1630
(3) HDD Managing Command
Add
Adds an HDD for recording. The HDD added is automatically formatted.
Add Used
Adds an HDD that has been used and formatted. There is no need to reformat. Only
possible when the HDD is added as a Primary Disk.
Remove
Removes the current HDD. HDDs can be reused without data loss by using the ‘Add
Used’ command.
Confirm Removed
Used when a removed HDD is still listed. ALL DATA WILL BE LOST!
1.2 Replacing HDDs
1.2.1 Checking HDDs
The DVR file system (VFS2) automatically detects bad sectors, and bad sectors detected are not used.
The cases below are for when an HDD fails or has some connection problems.
(1) When replaying is stopped, or the DVR is rebooted in a specific sector during playback, or when it is not
possible to search images by event.
(2) When recording is stopped and the “Disk Manager” shows the HDD type as [X]
1.2.2 When the primary disk fails
When the primary HDD fails, none of the data in the connected HDDs can be used. So the failed HDD should
be replaced and all the connected HDDs should be removed, added and formatted again.
1.2.3 When an auxiliary disk fails
The failed auxiliary disk should be replaced and reinstalled in “Disk Manager”. (“Add” -> “Format”).
58
2004. 07. 2004 (v 1.0)
Samsung Techwin
SVR-1630
1.3 Keeping Data
To keep stored data for certain periods or semi-permanently, you should separate and keep HDDs with data on
them.
1.3.1 Backup
(1) Connect a backup HDD to an IEEE1394 port.
(2) Go to playback mode by pressing the [Playback] button.
(3) Press the [COPY] button.
(4) Run the “Backup Manager” by selecting the “Backup Data” menu.
(5) Set the backup range and press the “Start” button after selecting the backup HDD.
<Note>
1. Backup HDDs should be formatted to the FAT32 type.
2. Backup data can be played on a PC with dedicated players such as SVR Manager or MiniPlayer.
3. Backup data is made as one “*.re3” file. If the file size is over 2GB, it may not be recognized normally
because of the PC file system structure.
4. In the course of backup, the “Auto Delete” function doesn’t work. If the HDD is full, recording may be
stopped instantly.
5. For more detailed information on the SVR Manager’s backup, please refer to the “SVR Manager User
Guide”.
Samsung Techwin
2004. 07. 2001 (v 1.0)
59
SVR-1630
1.3.2 Separating and Preserving HDDs
HDDs with data on them can be kept separately only when the HDD is installed and used in the DVR
(including the primary disk and RAID).
It is recommended to use an external HDD rather than an internal HDD. In other words only connect one
external HDD, and then keep it when it is full of data.
<Note>
Data on preserved HDDs can only be played when the HDD is connected to the DVR.
1.3.3 Cautions
For HDD handling or guarantees, apply to the after sales service of the HDD manufacturer. Any data losses
caused by user error shall not be subject to the warranty.
60
2004. 07. 2004 (v 1.0)
Samsung Techwin
SVR-1630
2. Changing Video Type
The SVR-1630 changes video type by automatically detecting the video signals. If there are no video
signals, the SVR-1630 refers to the internal jumper status and indicates the type.
Jumper Setting
Video Type
1-2
NTSC Video
2-3
PAL Video
<Note>
For changing the video type, contact your local vendor. If any problems occur due to unauthorized
changes, the warranty is invalidated.
Samsung Techwin
2004. 07. 2001 (v 1.0)
61
SVR-1630
3.
Using CD-Rom
3.1 CD- ROM DISC Components
Installation Guide
: SVR-1630 Installation Guide
User Guide
: SVR-1630 User Guide
SVR Manager
: SVR Manager User Guide
(SVR Remote Management Program)
Acrobat Reader
: Version 5.1
3.2 Preparation
To read the User Manual in the CD-ROM Disc, Adobe Acrobat 5.0 should be installed in the client PC.
<Note>
If Adobe Acrobat Reader is not installed in the client PC, use the CDROM’s Acrobat Reader program.
3.3 Reading the User Manual in CD-ROM
Follow the steps below to read the User Manual in CD-ROM.
(1) Insert the CD-ROM supplied into the PC’s CD-ROM drive
(2) Open the user guide PDF file.
62
2004. 07. 2004 (v 1.0)
Samsung Techwin
4.
SVR-1630
Specification
General
CPU
32bit RISC Processor (266MFPS)
Flash Memory
8MB
Main Memory
128MB
Boot Memory
64KB
OS
Embedded LINUX
Video Input Channel
16 Analog Channel
Compatible
Auxiliary
Storage Internal 3.5” IDE HDD 2EA (default 1EA)
Devices
Internal 3.5” IDE HDD RACK 1EA or CD-RW 1EA
External 2EA for IEEE-1394 SBP2 compatible
(Supports Max. 4Tbytes )
File System
Data-loss protection against power failure
Monitoring
Monitor A
30fps (NTSC), 25fps (PAL) per channel
1,4,9,16,13 Channel, Fixed & User Defined Sequence
VGA
640x480@60, 800x600@60, 1024x768@60 (Monitor A Output)
Monitor B
30fps (NTSC), 25fps (PAL)
1 Channel, Fixed & User Defined Sequence
Menu setting not available, except for playback and channel
information
Recording and Playback
Compression Method
WISE (Differential Wavelet)
Recording Speed
Up to 30ips per channel, total 240ips (NTSC)
Up to 25ips per channel, total 200ips (PAL)
Resolution
720x243 (NTSC)
720x288 (PAL)
Image Quality
5 steps. Adjustable by channel.
Combining frame rate and quality. Low/Normal/High/Custom
setting
Playback Speed
Max. 60fps in Monitor A or Monitor B
Playback Method
1/2x2/3x3/4x4 Split Screen on Monitor A,1 Channel on Monitor B
1x, 2x, 4x, 8x, 16x , 32x (Forward & Reverse Play)
Image Search
Time : Year/Month/Date/Time/Minute
Event : Search in Event Log
Step-Forward, Step-Reverse
Samsung Techwin
2004. 07. 2001 (v 1.0)
63
SVR-1630
Network
Dedicated Program
SVR Manager
Protocol
TCP/IP, ARP, ICMP, DHCP, PPPoE
Connector
10/100Mbps Ethernet (RJ-45)
SW Upgrade
Firmware upgrade via Network
Simultaneous Users
1 Admin
10 Users :
Monitoring (Max. 5 Users)
Playback (Max. 5 Users)
Security
Password (User or Administrator Authenticantion)
Environment
Operating Temperature
5~40℃
Storage Temperature
-10~50℃
Operating Humidity
30~80%, free of condensation
Storage Humidity
93% below, free of condensation
Data Backup/Expansion/Copy
Data Backup
Internal HDD Rack or external IEEE-1394 SBP2 compatible
HDD (FAT32 formatted)
Internal CD-R or External IEEE-1394 CD-R, 700MB CD-R
Data Copy
USB(1.1), 1 Channel Data + Miniplayer
Analogue VCR
VHS Video output for VCR
Backup Reminder
Daily / Weekly / Monthly
PTZ Control
Available Serial Ports
RS232 (2), RS422/485 (2)
Control Method (Local)
Front panel button & IR remote controller
(controls IP video channel as well)
Control Method (Remote)
On-screen PTZ control on PC
Preset Mode
16 points preset per channel
Group Mode
1 group per channel
64
2004. 07. 2004 (v 1.0)
Samsung Techwin
SVR-1630
Input/Output
Video
Input Level : 0.5 ~ 2.0 Vp-p
2 BNC , S-VHS and VGA output for Monitor A
1 BNC output for Monitor B
16 Loop through video
Audio
1 Input : Line-in, 1 Vpp
1 Output : Line-out, 1Vpp
Level : -7~8 (16 Step) Record level
AMP : 20dB amplifier for low level audio
Monitoring : Local and remote
Relay Output
4 Relay outputs (Max DC 30W, AC 62.5VA)
Relay Output Schedule
Daily : Day / Night
Weekly : Weekdays / Weekends
Conditions : MD, Sensor inputs
Sensor Input
16 Sensor inputs (Supports Dry contact)
Serial Port
Terminal : 1 RS-485 /422 (PTZ control, Max. 384Kbps)
RJ-45 : 1 RS-485 /422 (Keyboard interface)
1 RS-232C (PTZ or DVR chain )
9Pin D-SUB : 1 RS-232C
(Text input , Max. 230Kbps H/W Flow control)
Additional Functions
Digital Zoom
2x (Live & PlayBack Mode)
Alarm Notice
MD, Vloss, Sensor, Text
Alarm Data Preservation
Event triggered Video Data Preservation
Alarm Log
Log search
Log monitoring via OSD & Network
Pre/Post Alarm Recording
Pre : 1~10 seconds
Post : 1~60 seconds
Schedule Recording
Daily : Day / Night
Weekly : Weekdays / Weekends
Conditions : Schedule / Event
Text Data Storage
POS/ATM
transaction
information
archived
along
with
corresponding video data
Samsung Techwin
2004. 07. 2001 (v 1.0)
65
SVR-1630
Others
Power Supply
AC 100V - 240V, (50/60Hz), Max. 2A
Power Consumption
Typical 75W (with 1 internal HDD)
External Dimensions
Size (WⅹDⅹH)
420.0 x 440.10 x 92.5
Weight
8.3 Kg (with one HDD, one HDD Removable Rack)
66
2004. 07. 2004 (v 1.0)
Samsung Techwin
Samsung Techwin
2004. 07. 2001 (v 1.0)
SVR-1630
67

SVR-1630 Installation Guide

Transcription

Similar documents

Wire Diagram

Re-tuning: SAMSUNG Freeview TVs

Product datasheet

Zonare instructions - University of Florida

Untitled - Brookstone

Specifications

Flatbed

Disney Princess Magic Wand Laptop

Re-tuning:DURABRAND C5660 Freeview Box

Shredder for Optical + Magnetic Media