Ellure – Tile Look Walls

Ellure – Tile Look Walls
Ellure – Tile Look Walls - FITTING INSTRUCTIONS
Included in this package:
Other equipment that may be required
4x
White silicone

1x
Ellure – Tile Look Walls fitting
instructions (this booklet)

Drill
Adhesive application gun
Hole Saw
Jigsaw with 40 TPI tooth blade
Skillsaw with 100 tooth blade
Diamond continuous wheel in grinder
Included in this package:
Other equipment that may be required
6x
White silicone

1x
Ellure – Tile Look Walls fitting
instructions (this booklet)

Drill
Adhesive application gun
Hole Saw
Jigsaw with 40 TPI tooth blade
Skillsaw with 100 tooth blade
Diamond continuous wheel in grinder
Atlantis recommends this installation is undertaken by an experienced tradesperson.
2 WALL SHOWERS
1. Unpack and check-over the components.
2. Using the supplied white silicone, apply two continuous 8mm beads of silicone vertically down both walls, where
the Ellure corner flashing will adhere to the wall lining. Firmly press the Ellure corner flashing to the wall lining, in
the orientation shown, to suit your shower base (see figure 1 and 2).
The Ellure corner flashing is supplied with a “THIS WAY UP” indicator sticker to assist with correct positioning.
FIGURE 1 - LEFT HAND SHOWER BASE
FIGURE 2 - RIGHT HAND SHOWER BASE
3. Dry fit the Ellure Wall Panels into the corner flashing, to ensure the panels are positioned on the correct sides.
If you have purchased your Ellure Tile Look Walls with a feature panel, also dry fit the feature panel and panel
joiners at this time. Refer to the back page of these instructions for further information about fitting an Ellure
Feature Panel.
4. Carefully measure and mark the tapware penetrations
FIGURE 3
(figure 3). Drill a small pilot hole through the Ellure wall
panel from the front surface. Cut the large holes from
the back of the wall panel.
5. Trim the Ellure Wall Panels to the desired height (figure
3), if necessary. Please see the back page of these
instructions for further information about altering the
sheet size.
6. Remove the protective film off the back of the Ellure
Wall Panels and apply 8mm beads of silicone in vertical
lines at approx. 150mm centres, to the back of your
Ellure Wall Panels.
7. Apply a continuous bead of white silicone around the
shower base upstand, below the counter sunk screws (if
applicable) (figure 4).
FIGURE 4
8. Carefully place the Ellure wall panels into position and
press firmly into place. Smooth air out from behind the
Wall Panels with a padded block or similar, working
from the internal corner out. Prop liner in place if
necessary.
100% contact should be achieved between the Wall
Panels and shower base upstand.
9. Wipe any excess silicone off.
10. Fit Ellure Finishing Trim and Wall Channels, as per figure 8 and 9.
3 WALL SHOWERS
1. Unpack and check-over the components.
2. Using the supplied white silicone, apply two continuous 8mm beads of silicone vertically down both walls, where
the Ellure LEFT HAND corner flashing will adhere to the wall lining. Firmly press the Ellure LEFT HAND corner
flashing to the wall lining, in the orientation shown (figure 5).
The Ellure corner flashings are supplied with a “THIS WAY UP” indicator sticker to assist with correct positioning.
FIGURE 5
3. Dry fit the Ellure Wall Panels, following the order of installation shown in figure 6 and figure 7, to ensure the
panels are positioned on the correct sides.
If you have purchased your Ellure Tile Look Walls with a feature panel, also dry fit the feature panel and panel
joiners at this time. Refer to the back page of these instructions for further information about fitting an Ellure
Feature Panel.
4. Carefully measure and mark the tapware penetrations (figure 3).
FIGURE 6
Drill a small pilot hole through the Ellure wall panel from the
front surface. Cut the large holes from the back of the wall panel.
5. Trim the Ellure Wall Panel sheets to the desired height (figure 3),
if necessary. Please see the back page of these instructions for
further information about altering the sheet size.
5A. Apply two continuous 8mm beads of silicone vertically down
both walls, where the Ellure RIGHT HAND corner flashing will
adhere to the wall lining (figure 5).
6. Remove the protective film off the back of the Ellure Wall Panels
and apply 8mm beads of silicone in vertical lines at approx.
FIGURE 7
150mm centres, to the back of your Ellure Wall Panels.
7. Apply a continuous bead of white silicone around the shower
base upstand, below the counter sunk screws (if applicable)
(figure 4)
8. Following the order of panel installation shown in figure 6 and
figure 7, carefully place the Ellure wall panels into position and
press firmly into place. Smooth air out from behind the Wall
Panels with a padded block or similar, working from the internal
corner out. Prop liner in place if necessary.
100% contact should be achieved between the Wall Panels and
shower base upstand. Seal the
9. Wipe any excess silicone off.
10. Fit Ellure Finishing Trim and Wall Channels, as per figure 8 and 9.
FIGURE 8
FIGURE 9
Fitting Ellure Tile Looks Walls with Feature Panel
For showers where the feature wall is positioned on a side 1200mm or less, the Ellure Feature Panel will be
factory assembled. Please continue with your installation as per the steps in the main instructions.
For showers where the feature panel is on a side larger than 1200mm, the feature wall is supplied in two parts.
1. Dry fit the Ellure wall panels, following the order of installation shown in figure 10 then figure 7, to ensure panels
are on the correct sides.
FIGURE 10
FIGURE 11
2. As per step 4, carefully mark and cut the tapware
penetrations (figure 3)
3. As per step 5, trim the Ellure wall panels to the
desired height (figure 3), if necessary.
4. As per step 5A (for 3-wall showers), apply two
continuous 8mm beads on silicone vertically down
both walls, and firmly press the Ellure RIGHT HAND
corner flashing to the wall lining.
5. As per step 6, remove the protective film and apply
silicone vertically down the back of the Ellure wall
panels.
6. As per step 7, apply a continuous bead of silicone
around the shower base upstand.
7. As per step 8, follow the order of panel installation
shown in figure 10, carefully place the Ellure Wall
Panels into position and press firmly into place.
Referring to figure 11, join the Ellure feature and
adjacent panel by applying a continuous 5mm bead of
silicone vertically down the aluminium silver joining
strip. Continue panel installation as per figure 7.
Smooth air out from behind the Wall Panels with a padded block or similar, working from the internal corner out.
Prop liner in place if necessary.
100% contact should be achieved between the Wall Panels and shower base upstand.
8. Wipe any excess silicone off.
9. Fit Ellure Finishing Trim and Wall Channels, as per figure 8 and 9.
Cutting Ellure Tile Looks Walls
NOTE: This acrylic is harder than common wall liners; therefore it is also more prone to damage.
NOTE: Handle the panels carefully when drilling or cutting, and ensure the sheet is well supported around and/or under
where the cutting is being performed.
NOTE: It is advisable to leave the original protection film on the Ellure Wall Panel until all cutting is done, to protect the
face of the panel. You may also wish to tape over the face of the panel, along where you’re cutting, to protect the panel.
Hand tools that can be used to cut the Ellure Wall Panels:
Jigsaw with 40 TPI tooth blade, Skillsaw with 100 tooth blade, diamond continuous wheel in grinder, hand held buzzer.
A hand or belt sander may also be used.