Price Pages

Transcription

Price Pages

Kenwood USA Corporation
March 2009
Land Mobile Radio Division Price Guide
NX-200/300
TM
NEXEDGE VHF/UHF Digital & FM Portable Radios
All NX series portables include:
• Belt Clip (KBH-11)
• Universal Connector Cap
• Instruction Manual
• Premium Warranty: 3 Years*
* All Accessories / options: 1 Year
Purchase Battery, Charger, Antenna
separately
GENERAL FEATURES
• 5 W (136-174 MHz) Models
• 5 W (400-470, 450-520 MHz) Models
• 512 CH-GID / 128 Zones
• 12-Key Keypad Models
• 14 Character Alphanumeric Aliases
• RSSI Indicator
• Date & 12/24 Hour Time Clock
• Transmit/Busy/Call Alert/Warn LED
• On/Off Volume Knob
• 16-Position Mechanical Selector
• 6 Front PF & Menu Keys
• 2 Side PF Keys
• Emergency/AUX Key
• 500 mW Speaker Audio
• VOX Ready
• Emergency Call Features
• Emergency Man-Down Option
• Time Out Timer
• Busy Channel Lockout
• LCD Battery Status Indicator
• Low Battery Alert
• Weather-sealed ACC Connector
• MIL-STD-810 C/D/E/F
• MIL-STD “Driven-Rain”
• IP-54/55 Water & Dust Intrusion
• Easy Option Port
• Intrinsically Safe Option *
• VGS-1 Voice Guide/Storage Option
DIGITAL CONVENTIONAL MODE
• Individual & Group Selective Call
• Mixed FM/Digital Operation
DIGITAL COMMON
• NXDN® Digital Air Interface
• AMBE+2™ VOCODER
• 6.25 & 12.5 kHz Channels
• Over-the- Air Alias
• Paging Call
• Emergency Call
• All Group Call
• Status Messaging
• Remote Stun/Kill
• Remote Check
• Short & Long Data Messages
• GPS Location with Voice
• NXDN® Scrambler Included
FleetSync®/II (FM)
• PTT ID Digital ANI
• Selective Call & Group Call
• Emergency Status
• Caller ID Display
• Short Text Messages
• Power On/Off Status Messages
• Send/Display GPS (KMC-38GPS)
• PTT ID & Emergency GPS Reporting
• Status Message Block GPS Reporting
• VGS-1 GPS Data Storage
DIGITAL TRUNKING MODE
• Individual Private Call
• Group Call
• Call Queuing with Priority
• Multi-Site IP Network Compatible
SCAN
• Single Zone / Multi-Zone / List Scan
• Dual Priority Scan (Conventional)
FM MODES – GENERAL
• 25 & 12.5 kHz Channels
• FleetSync®/II
• DTMF Encode / Decode
• Companded Audio
• Voice Inversion Scrambler
• Encryption/ANI Board Control
FM CONVENTIONAL ZONES
• QT / DQT
• Two-Tone Decode
• Single/Two-Tone Encode
FM LTR® TRUNKED ZONES
• Kenwood LTR® Features
* Approved for Classes I, II & III, Div. 1, Groups C, D, E, F, G and are also approved for nonIncendive use in Class I, Div. 2, Groups A, B, C, D hazardous locations.
Note: Class I, Div 2 Group A & B Gases require use of a portable carrying case.
RADIO
NX-200K
NX-200K2
NX-300K
NX-300K2
NX-300K3
NX-300K4
LIST
136-174MHz 5W, 14 characters Alphanumeric LCD, 6 Control Keys
136-174MHz 5W, 14 characters Alphanumeric LCD, 6 Control Keys, Full Keypad
Page 1 of 4
684.00
734.00
684.00
684.00
734.00
734.00
NX-200・300
March 2009
FACTORY MUTUAL (FM) APPROVED MODELS
LIST
Must Order L-1101 & an Intrinsically Safe Battery per radio
NX-200-ISK
NX-200-ISK2
NX-300-ISK
NX-300-ISK2
NX-300-ISK3
NX-300-ISK4
ANTENNAS
KRA-26M
KRA-26M2
KRA-26M3
KRA-27M
KRA-27M2
KRA-27M3
KRA-22M
KRA-22M2
KRA-22M3
KRA-23M
KRA-23M2
KRA-23M3
KRA-25
KRA-28
LIST
VHF helical antenna 146-162 MHz
UHF whip antenna 440-490 MHz
VHF low-profile helical antenna 148-162 MHz
VHF Low-profile helical antenna 136-150 MHz
UHF low-profile helical antenna 450-490 MHz
High gain VHF helically loaded whip antenna 148-162 MHz
Broad-band VHF helically loaded whip antenna 140-170 MHz
BATTERIES AND CHARGERS
KNB-47L
KNB-48L
KNB-50NC
684.00
734.00
684.00
684.00
734.00
734.00
14.00
14.00
14.00
14.00
14.00
14.00
13.70
13.70
13.70
13.70
13.70
13.70
34.25
42.00
LIST
1950 mAh, Li-ion battery - requires KSC-32/326K charger
2000 mAh, Ni-MH battery - requires KSC-32/326K charger
105.00
122.50
157.50
[Intrinsically Safe Option]
KSC-32
Rapid rate single unit charger for KNB-31A/32N/33L/43L/47L/48L/50NC
70.00
Note: Includes 110/220V auto-switching AC adapter with U.S.-style line cord plug; requires plug adapter
for 220V Euro-style outlets (not supplied).
KSC-326K
KMB-30M
KMB-23
KVC-15
Rapid rate 6-unit charger for KNB-31A/32N/33L/43L/47L/48L/50NC
Wall Mount Bracket for KSC-326K/256K
Six Unit Charger Adapter for the KSC-16/20/24/25/32 chargers
(chargers not included)
Rapid rate DC vehicular charger adapter for the KSC-32 (chargers not included; includes
KSC-mobile bracket & cigarette lighter cable DC adapter)
CARRYING ACCESSORIES
KBH-11
KBH-8DS
KLH-6SW
KLH-148K
KLH-148K2
KLH-149K
KLH-149K2
630.00
33.75
191.00
119.00
LIST
Spring action belt clip (2.5")
Leather swivel belt loop with portable D-Ring attachment
Leather swivel belt loop / detachable swivel D-Ring back
Heavy duty leather carrying case for NX-200/300 (Non DTMF keypad models)
Heavy duty leather carrying case for NX-200/300 (DTMF keypad models)
Nylon carrying case for NX-200/300 (Non DTMF keypad models)
Nylon carrying case for NX-200/300 (DTMF keypad models)
Page 2 of 4
14.70
26.30
22.00
44.25
44.25
26.30
26.30
NX-200・300
March 2009
MICROPHONES & AUDIO ACCESSORIES
KMC-38GPS
LIST
GPS Speaker Microphone
402.50
[Intrinsically Safe Approved Accessory]
Note: FM Intrinsically Safe Approved except for Group C gases
KMC-41M
MIL-SPEC, IP54/55 Noise-canceling Speaker Mic
96.50
KMC-42WM
MIL-SPEC, IP67 (Immersion) Noise-canceling Speaker Mic
114.00
Important Note: Portable radio does not have an IP67 Immersion option; meets MIL STD810 rain
standards
KEP-1
3.5mm earphone kit for KMC-25/26/41M/42WM Speaker Mics
52.50
KCT-30
2.5mm Audio Accessory Adapter for KEP-3/4
64.00
KEP-3
30" Earphone kit w/ 2.5mm plug for KCT-30
51.50
KEP-4
54.75
KHS-11BE
2-wire palm mic w/earphone, universal connector (Beige)
156.50
KHS-11BL
2-wire palm mic w/earphone, universal connector (Black)
156.50
KHS-12BE
3-wire mini lapel mic w/earphone, universal connector (Beige)
184.00
KHS-12BL
3-wire mini lapel mic w/earphone, universal connector (Black)
184.00
KHS-14
Lt. Wt. Single muff headset w/boom mic & In-line PTT
126.00
KHS-15-BH
Hvy-duty noise reduction behind-the-headset w/noise cancelling boom mic & in-line PTT
420.00
KHS-15-OH
Hvy-duty noise reduction over-the-headset w/noise cancelling boom mic & in-line PTT
368.00
OPTION MODULES
KCT-48VU
LIST
External Vibration Unit
49.00
Note: Audio accessories cannot be used when this option installed.
KCT-57MS
Man-Down Internal Tilt Switch (Non-Mercury)
22.00
[Intrinsically Safe Approved Accessory]- Must be Kenwood installed for I.S.
®
Order L-1615 for CIM-1000, K-20, K-26 & L-1616 for NXDN /FleetSync® operations
CIM-1000K-26
GE-Star or MDC-1200 ANI Encode 26-Pin Plug-in Board
131.25
[Intrinsically SafeApproved Accessory] - Must be Kenwood installed for I.S.
Must order L-1088 for MDC-1200 or L-1089 for G-Star operations
Note: CIM-1000K-26 G-Star®/ MDC1200 Digital ANI (26-Pin Plug-in) Boards
Pre-programmed & installed boards require a completed CIM-1000K-26 Information and Order Sheet"
(available from Kenwood LMR Order Desk) submitted with order.
a) Order the appropriate Labor Code for MDC-1200 or G-Star.
b) CIM-1000K-26 boards can be ordered and shipped loose (if shipped loose, Kenwood will not program
the board).
CIM-CABLE
Serial Program Cable
61.25
Note: CIM-1000, K-20, K-26 programs via Windows Hyper terminal (Windows Ver 3.1 or later) or any
ProComm version; board must be installed in a powered radio for programming. The radio programmer
does NOT program the CIM-1000, K-20, K-26. CIM-CABLE is a DB-9 PC connector with 3 short lead with
clips and may require a PC serial extension cable. CIM-IRP (Part No 01-30-0510) Infrared wireless
standalone programmer, C-Plus line of desktop decoder displays and CIM-1000, K-20, K-26 Instruction
Manuals are available directly from Cimmarron Technologies 800-487-7184 at www.cimtechcorp.com
VGS-1
Voice Guide and Storage Unit
87.50
Page 3 of 4
NX-200・300
March 2009
SERVICE RELATED ACCESSORIES
KPG-36AM
KCT-53UM
KPG-111DK
LIST
Programming interface cable
USB Adapter for KPG-xxAM DB9F Programming Interface Cables
(DB9M - to - USB Type A connector)
Windows® Programming Software for NX Series
INSTALLATION / TUNING CHARGES
L-961
L-1084
L-1087
L-1088
L-1089
L-1100
L-1101
93.00
86.00
103.25
LIST
Assemble KMB-23 with six KSC-32K's (Rapid Rate, 120 Volt version only)
NX-200/300 Programming (with basic TX/RX check)
Install VGS-1 Voice Guide & Storage Unit
Install & Program CIM-1000K-26 for MDC-1200 in NX-200/300
Install & Program CIM-1000K-26 for GE-Star in NX-200/300
Multi-Channel Encoder Modification
Configure NX-200/300 for Intrinsically Safe
17.00
37.50
25.00
75.00
75.00
25.00
70.00
Must order an I.S. battery
L-1615
L-1616
NX-200/300 Portable KCT-57MS Installation (for CIM-1000K-26)
NX-200/300 Portable KCT-57MS Installation (for NXDN® / FleetSync®)
Page 4 of 4
20.00
20.00
NX-200・300
March 2009
TK-190
Low Band VHF Portable Radio
190 series portables include:
• Belt Clip
• Channel Selector
Mechanical stop & dressing plate
• Standard Warranty: 2 Years*
GENERAL FEATURES
• 6 W (29.7-37.0, 35.0-50.0 MHz)
• 16 Channels
• QT / DQT
• Priority Scan
• 7-Character Alphanumeric Aliases
• Lighted 13-Segment LCD
• Inverting LCD Display
• 3-Digit Sub-Display
• Function / Status LCD Icons
• Transmit / Busy / Call Alert / Warn LED
• 2 Top Panel PF keys
• 2 Side PF Keys
• Orange Emergency / AUX Key (side)
• 2-Position PF Toggle Switch (top)
• Encryption / ANI Board Control
• Two-Tone Decode
• Operator Selectable Tone
• Time Out Timer
• Battery Saver
• MIL-Spec Speaker Mic Options
• Windows® Programming & Tuning
• Windows® Firmware Uploading
• Front Panel Test / Tune
• Cloning
• MIL-STD-810 C/D/E
• Intrinsically Safe Option (USTC)
--- Must Order L-835 or L-979 for Intrinsically Safe Option --* USTC (NFPA/NEC) Intrinsically Safe Models:
Meets Intrinsically Safe Classes I, II & III, Div. 1, Groups C, D, E, F, G hazardous locations and
Non-Incendive Class I, Div. 2, Groups C, D hazardous locations.
Purchase Battery, Charger
& Antenna, Separately
RADIO
TK-190K
TK-190K2
LIST
VHF Low Band 29.7 – 37.0 MHz 6W, 16 Channels
674.00
674.00
Important Notice:
If this transceiver is programmed for more than one channel, the transmit frequencies must be
within a 500 kHz range.
The physical condition of the antenna may affect the radio's performance. If the original KRA-21 antenna is
worn, bent or damaged, immediately have your Kenwood authorized dealer replace the antenna with a
new, properly adjusted KRA-21 antenna. Failure to follow these instructions may cause poor performance,
damage to your transceiver, and may also place excess transmitter energy on the metal portions of your
radio, which could make the transceiver uncomfortable to handle when transmitting. When transmitting, if
your hand feels uncomfortable, contact your Kenwood dealer for a transceiver inspection, and possible
antenna replacement.
ANTENNA
KRA-21
LIST
Tunable VHF Low Band helical antenna 29.7-50MHz.
42.00
Note: Antenna band width is 1 MHz
Caution: the TK-190 antenna must be cut per the antennas cutting chart and instructions. Failure to do so
will result in a poorly matched antenna, poor performance and most probably excessive and damage in
the transmitters final power amplifier circuit.
Page 1 of 3
TK-190
March 2009
KNB-17A
KNB-17BK
LIST
1500 mAh, Ni-Cd battery
70.00
105.00
KNB-21N
KNB-22N
KNB-22NC
1600 mAh, Ni-MH battery - requires KSC-24 charger
63.00
73.50
122.50
KBP-4
KSC-19
KSC-19M
KSC-24
KSC-24E
KMB-16
KMB-23
KVC-3
KVC-4
KVC-5A
AA Alkaline Refillable Battery Pack (12 AA; 9V) cells not included
110 volt Regular rate single unit desk charger for KNB-16/17A/17B
110 volt Rapid rate single unit charger
for KNB-14/15/16/17A/17B/20N/21N/22N/22NC
for KNB-14/15/16/17A/17B/20N/21N/22N/22NC
Six Unit Charger Adapter for the KSC-16/20/24/25 chargers
Regular rate DC vehicular charger adapter for the KSC-15/17/19/30 chargers (chargers not
included)
Rapid rate DC vehicular charger adapter for the KSC-16/18/20/24/25 chargers
Vehicular D.C. Charger for 80/90/5400 Portables with NiCd or NiMH Battery
KBH-10
KBH-8DS
KLH-6SW
KLH-78B
KLH-88
KLH-137ST
KLH-141
62.00
62.00
173.00
191.00
63.00
84.00
357.00
LIST
Spring action belt clip
Heavy duty leather carrying case
for TK-190/290/390/5400 (Non DTMF keypad models)
Cordura Nylon carrying case for TK-190/290/390/5400 (Non DTMF keypad models)
Firemen's Heavy-Duty Leather Shoulder Strap
for a Heavy-Duty Leather Case (KLH-75B/76B/78B/79B//92/122/123/133/148)
Extra Heavy-Duty Cordura Nylon carrying case
for TK-190/290/390 (all battery packs; no keypad access)
KEP-1
43.00
36.75
36.75
8.35
26.30
22.00
44.25
26.30
36.75
34.75
LIST
52.50
KCT-30
64.00
KEP-3
51.50
KEP-4
54.75
KMC-25A
MIL-SPEC, Noise canceling Speaker mic
96.50
Note: KMC-25 is not compatible with the TK-190 due to the effects of RF on it at low band frequencies; the
KMC-25A is the compatible model. The KMC-26 Speaker microphone with antenna connector CANNOT
be used due to the inadequate ground plane properties on a speaker microphone at low band frequencies
(the TK-190 does not have an RF pin on its accessory connector).
KHS-11BE
156.50
KHS-11BL
156.50
Page 2 of 3
TK-190
March 2009
MICROPHONES & AUDIO ACCESSORIES - CONT'D
KHS-12BE
LIST
184.00
KHS-12BL
184.00
KHS-14
126.00
KHS-15-BH
420.00
KHS-15-OH
368.00
OPTION MODULES
CIM-1000
LIST
GE-Star or MDC-1200 ANI Encode Board
131.25
Note: CIM-1000 G-Star®/ MDC1200 Digital ANI Boards
Pre-programmed & installed boards require a completed CIM-1000 Information and Order Sheet"
b) CIM-1000 boards can be ordered and shipped loose (if shipped loose, Kenwood will not program the
board).
CIM-CABLE
61.25
KCT-57MS
22.00
Order L-1617 for CIM-1000, K-20, K-26 & L-1618 for FleetSync® operations
KPG-36AM
KCT-53UM
LIST
KPG-59DK
Windows® Program Software for TK-190/6110 (Version 2.00)
*****************
Call Kenwood Parts at 800-367-7514 to order the following:
E30-3325-05
Portable-to-Portable Cloning cable (For TK-190/290/390/480/481 Only)
L-911
L-835
93.00
86.00
68.50
65.00
LIST
TK-190/TK-6110 Programming (with basic TX/RX check)
Configure TK-190/290/390 for Intrinsically Safe
25.00
70.00
Must order KNB-17BK
L-979
Configure TK-190/290/390 for Intrinsically Safe
70.00
Must order KNB-22NC
L-836
L-961
L-837
L-870
Assemble KMB-16 with six KSC-20's/24's
L-914
L-1038
L-1039
L-1617
L-1618
Cut KRA-21 Low Band Antenna
Install KNB-17A/17BK battery
Simultaneous transpond and alert feature up-grade for 90-series mobiles & portables
TK-190/290/390 CIM-1000/MDC1200 ENCODER INSTALLATION
TK-190/290/390 CIM-1000/GE STAR ENCODER INSTALLATION
90 PORTABLE KCT-57MS INSTALLATION (FOR CIM-1000)
80/90 PORTABLE KCT-57MS INSTALLATION (FOR FLEETSYNC)
Page 3 of 3
15.00
17.00
0.00
50.00
10.00
75.00
75.00
20.00
20.00
TK-190
March 2009
TK-5210 / 5310
VHF/UHF FM & P25 Digital Portable Radios
All 5X10 series portables include:
Order packages to include Battery
& Charger,
or purchase Battery, Charger, and
Antenna separately.
Basic Model
No LCD display; no front panel keys
Standard Model
16-Character Alphanumeric LCD
4 control keys
12 Keypad Model
16-Character Alphanumeric LCD
4 control keys
DTMF/Function keypad
GENERAL FEATURES
• 5 Watt (136-174 MHz)
• 4 Watt (450-520, 380-470 MHz)
• 50 Zones / 512 Channels (K-K6)
• 16 Zones / 64 Channels (K7)
• Personality Lists
• Backlit Dot Matrix LCD
• RSSI Indicator
• 16-Position Selector Knob
• 2-Position PF Lever Switch
• 3-Position PF Concentric Switch
• 4 Front Menu-Driven PF Keys
• 3 Side PF Keys
• Orange Emergency / AUX Key
• 12-Key DTMF / PF Keypad
• Enhanced Kenwood Audio
• Voice Annunciation
• VOX Ready
• Emergency Features
• Tactical Group
• Battery Level Indicator
• Transceiver Password
• Self-Programming & Tuning
• Cloning
• Weather-Sealed Accessory Connector
• IP54/55 Water & Dust Protection
• Immersion (IP66/67) Option
• Intrinsically Safe Option*
* Approved for Classes I, II & III, Div. 1, Groups D, E, F, G and are also approved for nonIncendive use in Class I, Div. 2, Groups A, B, C, D hazardous locations.
SCAN TYPES (FM & P25)
• Single Zone/Multi-Zone Scan
• Scan Lists
• Conventional Scan
• Limited Talk Group Scan
• Priority Monitor Scan
• Dual Priority Scan
FM
• QT / DQT
• Two-Tone Decode / Encode
• DTMF Encode / Decode / Stun
• Special Alert Tone Patterns
• Companded Audio
FleetSync® (FM)
• FleetSync® or FleetSync® II
• Emergency & Stun Statuses
• Selective & Group Call
• Text Messaging
P25 DIGITAL
• P25 Digital Conventional
• P25 Digital Trunking Option
• IMBETM VOCODER
• Talk Group ID Lists
• Individual ID Lists
• Remote Monitor/Remote Check
• Radio Inhibit
• Encryption Key Delete
• Encryption Key Zeroize (SCM required)
• Encryption Key Retention (SCM required)
• DES Encryption Options
• AES / DES Encryption Options
• KPG-93 KVL Key Loader Interface Cable
PACKAGES
TK-5210K2-NKP
TK-5210K2-LKP
TK-5210K7-NKP
TK-5210K7-LKP
TK-5310K2-NKP
TK-5310K2-LKP
TK-5310K7-NKP
TK-5310K7-LKP
LIST
VHF NiMH Battery Package (TK-5210K2 + KNB-32N + KSC-32 + KBH-11)
VHF Li-Ion Battery Package (TK-5210K2 + KNB-43L + KSC-32 + KBH-11)
VHF NiMH Battery Package (TK-5210K7 + KNB-32N + KSC-32 + KBH-11)
VHF Li-Ion Battery Package (TK-5210K7 + KNB-43L + KSC-32 + KBH-11)
UHF NiMH Battery Package (TK-5310K2 + KNB-32N + KSC-32 + KBH-11)
UHF Li-Ion Battery Package (TK-5310K2 + KNB-43L + KSC-32 + KBH-11)
UHF Ni-MH Battery Package (TK-5310K7 + KNB-32N + KSC-32 + KBH-11)
Page 1 of 7
1,994.50
2,070.00
1,557.50
1,633.00
1,994.50
2,070.00
1,557.50
1,633.00
TK-5210・5310
March 2009
RADIO
TK-5210K
TK-5210K2
TK-5210K3
TK-5210K7
TK-5310K
TK-5310K2
TK-5310K3
TK-5310K4
TK-5310K5
TK-5310K6
TK-5310K7
LIST
136-174MHz 5W, 512 CH, Basic Model
136-174MHz 5W, 512 CH, Standard Model
136-174MHz 5W, 512 CH, 12 Keypad Model
450-520 MHz 4W, 512 CH, Basic Model
450-520 MHz 4W, 512 CH, Standard Model
450-520 MHz 4W, 512 CH, 12 Keypad Model
1,225.00
1,838.00
1,995.00
1,400.00
1,225.00
1,837.00
1,995.00
1,225.00
1,837.00
1,995.00
1,400.00
LIST
TK-5210-ISK
TK-5210-ISK2
TK-5210-ISK3
TK-5210-ISK7
TK-5310-ISK
TK-5310-ISK2
TK-5310-ISK3
TK-5310-ISK4
TK-5310-ISK5
TK-5310-ISK6
TK-5310-ISK7
136-174MHz 5W, 512 CH, Basic Model
136-174MHz 5W, 512 CH, 12 Keypad Model
ANTENNAS
KRA-26M
KRA-26M2
KRA-26M3
KRA-27M
KRA-27M2
KRA-27M3
KRA-22M
KRA-22M2
KRA-22M3
KRA-23M
KRA-23M2
KRA-23M3
KRA-16M
KRA-16M2
KRA-16M3
KRA-17M
KRA-17M2
KRA-17M3
KRA-25
KRA-28
KRA-29
1,225.00
1,838.00
1,995.00
1,400.00
1,225.00
1,837.00
1,995.00
1,225.00
1,837.00
1,995.00
1,400.00
LIST
VHF stubby antenna 148-162 MHz
UHF stubby antenna 450-490 MHz
Broad Band UHF Whip Antenna 380-430 MHz
Page 2 of 7
14.00
14.00
14.00
14.00
14.00
14.00
13.70
13.70
13.70
13.70
13.70
13.70
13.70
13.70
13.70
13.70
13.70
13.70
34.25
42.00
36.75
TK-5210・5310
March 2009
KNB-32N
KNB-33L
KNB-31A
KNB-41NC
LIST
1700 mAh, Ni-Cd battery - requires KSC-32/326K charger
87.50
105.00
70.00
136.50
KNB-43L
KNB-49PL
3300 mAh, Li-Polymer battery - requires KSC-32/326K charger
4500 mAh, Primary Lithium battery
163.00
84.00
Note: Non-Rechargeable (please recycle all batteries properly)
10 year Shelf Life (approx. 1% charge degradation per year when properly stored: +50 oF to +86 oF @
less than 70% humidity
KBP-6
68.50
Note: the color of the case is orange
KSC-32
70.00
KSC-326K
KMB-30M
KMB-23
KVC-15
KVC-18
KBH-11
KBH-8DS
KLH-6SW
KLH-133K
KLH-133K2
KLH-133K3
KLH-134K
KLH-134K2
KLH-134K3
KLH-137ST
119.00
446.50
LIST
Heavy duty leather carrying case for TK-5210/5310 Basic Models
Heavy duty leather carrying case for TK-5210/5310 Standard Models
Heavy duty leather carrying case for TK-5210/5310 12 Keypad Models
Cordura Nylon carrying case for TK-5210/5310 Basic Models
Cordura Nylon carrying case for TK-5210/5310 Standard Models
Cordura Nylon carrying case for TK-5210/5310 12 Keypad Models
KMC-38GPS
630.00
33.75
191.00
14.70
26.30
22.00
44.25
44.25
44.25
26.30
26.30
26.30
36.75
LIST
GPS Speaker Microphone (FM Conventional mode only -- does not operate in P25 modes)
402.50
KMC-41M
96.50
KMC-42WM
114.00
KMC-26
MIL-SPEC, Noise canceling Speaker mic w/Antenna Connector (ant. not incl.)
115.50
KEP-1
52.50
KEP-3
51.50
KEP-4
54.75
KCT-30
64.00
KCT-51
Hirose 6-pin Adapter (adapts KVL/aftermarket audio acc. to portable connector)
Page 3 of 7
215.00
TK-5210・5310
March 2009
KHS-11BE
LIST
156.50
KHS-11BL
156.50
KHS-12BE
184.00
KHS-12BL
184.00
KHS-14
126.00
KHS-15-BH
420.00
KHS-15-OH
368.00
ENVIRONMENTAL SPEC. OPTIONS
KWD-IM10
LIST
Immersion Option Kit
368.00
Must Order L-987
Note: Initial Installation Kenwood Long Beach Tuning Dept. only. To maintain immersion certification, recertification is required every 2 years available at Kenwood Authorized Service Centers only. Call an ASC
for return procedure ($315.00 List Price)
FIRMWARE OPTIONS
KWD-TR20
LIST
Trunking Option for TK-5210/5710/5310/5810
875.00
Must order L-1055
Note: KPG-95DK Requires Network Level License ID to program trunked network radio parameters (see
KPG-95D for purchase restrictions & requirements)
Compatible with TK-5210 Version 2 (SN 80600001 or later); TK-5310 (SN 809xxxxx or later); TK-5710
Version 2 (SN806xxxxx); TK-5810 (SN 809xxxxx or later)
KWD-RK20
OTAR Option for KWD-AE20K Encryption Module for P25 Conventional Only;
models TK-5x10 (VER2; except K7)
830.00
Must order:
• With KWD-AE20K (SN 005xxxxx or later)
• L-1108 for portable installation (no charge)
Notes:
• Provides OTAR on P25 Conventional only (TIA/EIA-102.AACA compliant; not for use over trunked
systems)
• Compatible with Motorola KMF P25 conventional OTAR
• Not compatible with Motorola-proprietary (non-TIA/P25) KMF features
• Not compatible with K7 64 Ch Model
• Requires KPG-95D V5.40 or later for radio programming
• Option deletes self-programming, cloning and analog FleetSync® (except PTT ID/Emergency) when
installed.
KWD-RK20 is an U.S. DOC/BIS Export Controlled Item (ECCN 5D002A)
- See IMPORTANT NOTES -
SOFTWARE OPTIONS
KPG-114DE
LIST
DES Encryption Software Key Loader for KWD-DE21K/KWD-AE21K
368.00
Note: KPG-114DE is a U.S. DOC/BIS Export Controlled Item (ECCN 5D992A.1)
KPG-113AE
AES/DES Encryption Software Key Loader for KWD-DE21K/KWD-AE21K
525.00
Note: KPG-113AE is a U.S. DOC/BIS Export Controlled Item (ECCN 5D002A)
Page 4 of 7
TK-5210・5310
March 2009
OPTION MODULES
KWD-DE20K
LIST
DES Encryption Module for TK-5210/5710/5310/5810
578.00
[Intrinsically Safe Approved Accessory] - Order L-1559 if installation is required.
KWD-DE20K requires: a Motorola KVL3000 or KVL3000 Plus key loader device.
KWD-DE20K is a U.S. DOC/BIS Export Controlled Item (ECCN 5A992A)
- See IMPORTANT NOTES Other Option Board Installation: CIM-1000K-26 ANI, VGS-1 & aftermarket ANI/encryption boards cannot
be installed with a KWD-DE20K or KWD-AE20K (portable option port are space limitation)
KWD-DE21K
578.00
Order L-1560 if installation is required
Note: Requires KPG-114DE or KPG-113AE software key loader or Motorola KVL3000 Plus key loader
device. KWD-DE21K is a U.S. DOC/BIS Export Controlled Item (ECCN 5A992A)
KWD-AE20K
AES FIPS140-2 & DES Encryption Module for TK-5210/5710/5310/5810
998.00
(except K7 Portable)
[Intrinsically Safe Approved Accessory] - Order L-1236 if installation is required.
KWD-AE20K requires: a Motorola KVL3000 Plus key loader device.
KWD-AE20K is an U.S. DOC/BIS Export Controlled Item (ECCN 5A002A.1)
KWD-AE21K
AES & DES Encryption Module for TK-5210/5710/5310/5810
998.00
(except K7 Portable)
Order L-1237 if installation is required.
Note: Requires KPG-113AE software key loader or Motorola KVL3000 Plus key loader device. KWDAE21K is an U.S. DOC/BIS Export Controlled Item (ECCN 5A002A.1)
KCT-48VU
49.00
KCT-48VU does not support the P25 digital mode calling or paging features
KCT-57MS
22.00
Order L-1613 for CIM-1000, K-20, K-26 & L-1614 for FleetSync®/P25 Emergency operations
CIM-1000K-26
131.25
Must order L-1022 MDC-1200 or L-1023 for G-Star operations
the board).
CIM-CABLE
61.25
VGS-1
87.50
Page 5 of 7
TK-5210・5310
March 2009
KPG-95DK
LIST
Windows® Programming Software for TK-5210/5310/5710/5810
628.00
Includes "Dealer Level License ID" for FM & P25 Conventional modes only.
See L-989 KPG-95DK Network Level ID (Trunking System Privileges_ - Restricted Purchase
Requirements.
Note: A Dealer Level License ID can load network data files provided by a Network Level Licensed KPG95DK, but cannot change trunked network parameters.
KPG-95D V4.00 or later (no key loader): TK-5210/5710/5310/5810 VER1 & VER2 Radios (all Serial
No.s)
Note: A Kenwood Key Loader for VER2 radios is NOT currently available (see KWD-DE20/KWD-AE20)
KPG-95D V3.11 or earlier (no key loader): TK-5210/5710 VER1 Radios (before SN 8060000) ONLY
KPG-95DTKL VX.XX (includes key loader; discontinued): TK-5210/5710 VER1 Radios (before SN
8060000) ONLY
KPG-36AM
KCT-53UM
KPG-93
TK-5210/5310/5400 KVL-3000/3000 Plus Interface Cable
L-961
L-986
93.00
86.00
262.50
LIST
Configure TK-5210-IS/TK-5310-IS for Intrinsically Safe
17.00
100.00
L-987
Immersion Option Certification
N/C
(Must purchase Immersion Option Kit, KWD-IM10 separately)
L-989
KPG-95DK Network Level ID (encrypted data file)
132.00
Note: Enables Trunking system programming privileges; See KPG-95DK Network Level ID (Trunking
System Privileges)
- Restricted Purchase Requirements L-989- KPG-95DK Network Level ID (Trunking System Privileges)
The KPG-95D only ships with a "Dealer Level License ID" which permits Conventional FM and P25
Conventional radio programming privileges only. For radios with the P25 Trunking option installed,
trunked/network programming privileges require a "Network Level License ID" generally reserved ONLY
for the system owner or the system owners authorized operators/service centers. Purchasing the KPG95DK Network Level License ID will require 1) Written verifiable authorization from the systems
owner/operator. 2) The 3-digit hexadecimal P25 System ID from the system owner/operator. 3) Purchase
of a L-989 : KPG-95D Network Level ID option. This option will include an encrypted KPG-95D "System
Key Data File" containing the 16-digit Network Level License ID & 3-digit hexadecimal System ID code.
L-990
L-1022
L-1023
L-1055
TK-5210/5310 Programming (Basic TX/RX check only with factory test freq.s or
dealer/customer provided KPG-95D data file)
Install & Program CIM-1000K-26 for MDC-1200 in TK-5210/5310
Install & Program CIM-1000K-26 for GE-Star in TK-5210/5310
Install KWD-TR20 Trunking Option in TK-5210/5310
125.00
75.00
75.00
N/C
(Must purchase KWD-TR20K separately)
L-1108
Install KWD-RK20 OTAR Option in TK-5210/5310
N/C
(Must purchase KWD-RK20 separately)
L-1236
Install KWD-AE20K in TK-5210/TK-5310 Portables
75.00
(Must purchase module separately)
L-1237
Install KWD-AE21K in TK-5210/TK-5310 Portables
75.00
L-1559
Install KWD-DE20K in TK-5210/TK-5310 Portables
75.00
L-1560
Install KWD-DE21K in TK-5210/TK-5310 Portables
75.00
INSTALLATION / TUNING CHARGES - CONT'D
L-1613
L-1614
LIST
5210/5310 Portable KCT-57MS Installation (for CIM-1000K-26)
5210/5310 Portable KCT-57MS Installation (for P25/FleetSync ®)
Page 6 of 7
20.00
20.00
TK-5210・5310
March 2009
-- IMPORTANT NOTES -Encryption modules, key loaders and radios containing encryption are export controlled by the U.S. Department of Commerce Bureau of Industry & Security EAR
regulations and may either require an Export License, are eligible for a License Exception (ENC) or are exportable with No License Required (NLR) depending on the
country, the consignee and the intended use. High level encryption is a special commodity that may require an export license to most countries. See www.bis.gov for more
information regarding export regulations. DO NOT SHIP encryption items outside the U.S. without proper DOC/BIS Export Licenses and/or compliances.
Kenwood may request the following information to be submitted at time of order (this information must meet Kenwood internal approvals prior to shipment
even if being returned to Kenwood later:
a) Initial Destination: Initial delivery point if different from Ultimate Destination
(customer distribution center, headquarters, dealership, manufacturer's representative)
* Business/Agency Name:
* Address:
* Contact Person Name:
* Contact Phone:
b) Ultimate Destination: Final delivery point(s); deployment/distribution
* Address:
* Contact Phone:
c) Intended Use of Radios: Law enforcement, security, operations, etc.
-------------------------------------------------------------------------------------------------KWD-AE20 AES FIPS140-2 SCM , NIST Validation & Customer Shipping
A secure delivery method direct to the end user customer is required by the NIST AES FIPS 140-2 validation rules. For U.S. Federal Government entities the SCM must
ship from Kenwood USA Corporation directly to the end user customer by a trusted carrier (FEDEX, UPS or a designated Kenwood USA Corporation employee);
shipping/handling by a dealer or other entity is not acceptable. This may or may not be required by local/state government agencies or business/industrial users. Please
check with the end use customer about their AES encryption handling requirements before ordering. Kenwood will not be responsible for shipments of KWD-AE20K
modules to erroneous destinations specified on an order.
Page 7 of 7
TK-5210・5310
March 2009
ProTalk® XLS TK-3230
UHF BRS Portable Radio
XLS series portable includes:
• Spring action belt clip
• Rapid Rate Drop-in charger
• Fixed Antenna
• 2000 mAh Li-ion Battery
GENERAL FEATURES
• UHF 1.5 Watt or 500 mW Transmit Power
• Extra Durable Polycarbonate Housing
• Small (2 1/16” W x 1 1/8” D x 4 1/16” H) & Lightweight (5.5 oz)
• Li-Ion battery with over 14 Hours Talk Time (5/5/90 duty cycle)
• Over 18 Hours Talk Time (with Battery Save On) 5/5/90 duty cycle
• 2 Channel Operation (factory pre-set)
• 56 User-Programmable Memory Bank Frequencies
• Channel Scan
• Wireless Cloning Mode
• Key Lock/Super Lock
• User Programmable QT (39) and DQT (83) Signaling
• 10 Call Alert Tones
• Voice Scrambler
• Speaker Mute Function
• Compander
• SelCall (for Caller ID)
• LCD Battery Meter & Low Battery Alert
• VOX (Voice-activated transmit) w/3 Sensitivity Levels
• Time Out Timer
• 2 Color Transmit / Busy LED/ Backlit LCD Display
• 3 Function Keys: Menu, Call, Monitor
• Audio Accessory Jack
• Antenna (fixed non-removable)
• Passes 8 Rugged Mil-Spec 810 C, D, E & F Standards
RADIO
TK-3230K
LIST
464-467 MHz UHF 1.5W or 500 mW, 2 Ch. Ultra Compact Portable Transceiver
KNB-46L
KSC-37
KMB-25
KMB-27
LIST
Li-Ion battery (Same as supplied with TK-3230)
Li-Ion Rapid rate charger (Same as supplied with TK-3230)
Six Unit Charger Adapter for the KSC-37 chargers (chargers not included)
Six Unit Charger Adapter for the KSC-37 chargers (chargers not included)
KBH-14M
KLH-150
47.25
31.50
191.00
208.50
LIST
Spring action belt clip (Same as supplied with TK-3230)
Nylon case for TK-3230 (Black)
KEP-2
KHS-10-BH
KHS-10-OH
KHS-7
KHS-7A
KHS-8BE
KHS-8BL
KHS-9BE
KHS-9BL
KHS-22
KHS-23
225.00
9.35
14.70
LIST
2.5mm earphone kit for KMC-17/45 Speaker Mic
Hvy-duty behind-the-headset w/noise cancelling boom mic & in-line PTT
Hvy-duty over-the-headset w/noise cancelling boom mic & in-line PTT
Single muff headset w/boom mic
Lt. Wt Single muff headset w/boom mic & in-line PTT
Two-Wire palm mic w/earphone (beige)
Two-Wire palm mic w/earphone (black)
Three-Wire lapel mic w/earphone (beige)
Three-Wire lapel mic w/earphone (black)
Behind-the-Head Headset with flexible boom mic and in-line PTT single ear receiver
2-Wire Cell-style Earbud Clip/PTT Palm Mic (medium duty)
Page 1 of 2
52.50
368.00
336.00
70.00
105.00
103.25
103.25
166.00
166.00
41.00
55.50
TK-3230
March 2009
KHS-25
KHS-26
KHS-27
KMC-45
KMC-21
HMC-3
Headset w/ D-Ring Ear Hanger w/ PTT & Boom Mic
Clip Mic w/earphone
D-Ring Ear Hanger w/PTT & Mic
MIL-SPEC, IP54/55 Speaker microphone (Built-in 2.5mm miniature earphone jack)
Compact speaker microphone
Headset w/PTT & VOX
Page 2 of 2
LIST
24.50
28.00
24.50
86.00
51.50
63.00
TK-3230
March 2009
TK-3173
UHF Trunking & Conventional Compact Portable Radio
All 173 series portables include:
• 2-PIN Connector Cap
Order packages to include Battery &
Charger, or purchase Battery, Charger,
and Antenna separately.
GENERAL FEATURES
• 4 W, 450-490 MHz
• Conventional & LTR® Zones
• Backlit LCD
• 4 Front Panel PF keys
• 3 Side PF Keys
• 500 mW Audio Power
• Companded Audio
• Easy Option Port (20-Pin)
• QT / DQT
• Call Key
• Time Out Timer
• Speaker Mic Options
• Field Programming & Tuning
• Cloning
CONVENTIONAL ZONES
• 128 Channels / 128 Zones
• QT / DQT
• Two-Tone Decode
• Single / Two-Tone Encode
• Single Priority Scan
• Single & Multi-Zone Scan
• List Scan
• Voice Inversion Scrambler Built-in
• VOX Ready
• Battery Saver
TRUNKED ZONES
• 250 GID / 128 Zones
FleetSync®
• PC Serial Interface
--- Must Order L-1000 for Intrinsically Safe Option --* Approved for Classes I, II & III, Div. 1, Groups A, B, C, D, E, F, G and are also approved for
non-Incendive use in Class I, Div. 2, Groups A, B, C, D hazardous locations.
PACKAGES
TK-3173K-AKP
TK-3173K-LKP
LIST
UHF Standard Package (TK-3173K + KNB-25A + KSC-30 + KRA-27M)
UHF Premium Package (TK-3173K + KNB-35L + KSC-25 + KRA-27M)
RADIO
TK-3173K
TK-3173K4
LIST
450-490 MHz 4W, 128 CH / 128 Zone Conventional; 8 Character LCD, 4-key
450-490 MHz 4W, 128 CH / 128 Zone Conventional; 8 Character LCD, 4 + 12-key
ANTENNAS
KRA-23M
KRA-27M
495.25
573.00
399.00
448.00
LIST
UHF Low-profile helical antenna 450-490 MHz
Page 1 of 3
13.70
14.00
TK-3173
March 2009
KBP-5
KNB-25A
KNB-26N
KNB-35L
KNB-40LC
LIST
2000 mAh, Ni-MH battery
49.00
50.75
70.00
98.00
112.00
KSC-25
KSC-25E
KSC-30
KSC-30E
KSC-256K
KMB-30M
KMB-16
KMB-23
KVC-3
KVC-4
110 volt Rapid rate single unit charger for KNB-25A/26N/35L/40LC
110 volt Regular rate single unit charger for KNB-25A/26N
Rapid rate 6-Unit charger for KNB-25A/26N/35L/40LC
included)
62.00
62.00
31.50
31.50
630.00
33.75
173.00
191.00
63.00
84.00
LIST
KLH-138
Heavy-Duty Leather Case w/Swivel Belt Loop for 160/170/173 (Non DTMF keypad)
49.00
KLH-139
KBH-12
KBH-13DS
KWR-1
Heavy-Duty Leather Case w/Swivel Belt Loop for 170/173 (w/ DTMF keypad)
49.00
8.35
28.85
29.85
Water resistant bag
KEP-2
LIST
52.50
KHS-1
Headset with VOX/PTT (light-duty use)
65.25
[Intrinsically Safe Approval Accessory]
KHS-10-BH
368.00
KHS-10-OH
336.00
KHS-7
70.00
KHS-7A
105.00
KHS-8BE
KHS-8BL
KHS-9BE
KHS-9BL
KHS-22
KHS-23
Behind-the-Head Headset with flexible boom mic and in-line PTT single ear receiver (low
profile wire head band)
Page 2 of 3
103.25
103.25
166.00
166.00
41.00
55.50
TK-3173
March 2009
KHS-25
KHS-26
KHS-27
KMC-17
Clip Mic w/earphone
Speaker microphone (Built-in 2.5mm miniature earphone jack)
LIST
24.50
28.00
24.50
86.00
KMC-45
KMC-21
86.00
51.50
LIST
KPG-22AM
KCT-53UM
Programming interface Cable
KPG-101DK
Windows® Programming Software for TK-2170/3170/3173
OPTION MODULES
KCT-57MS
191.00
86.00
103.25
LIST
22.00
CIM-1000K-20
131.25
[Intrinsically SafeApproved Accessory]- Must be Kenwood installed for I.S.
(available from Kenwood LMR Order Desk) submitted with order. a) Order the appropriate Labor Code for
MDC-1200 or G-Star.
the board).
CIM-CABLE
61.25
L-836
L-961
L-993
L-1001
LIST
Assemble KMB-16 with six KSC-25
Assemble KMB-23 with six KSC-24/25/32 (Rapid Rate, 120 Volt versions only)
TK-3173 Programming (with basic TX/RX check)
Configure TK-3173 for Intrinsically Safe
15.00
17.00
37.50
70.00
L-1049
L-1050
L-1608
L-1609
Install & Program CIM-1000K-20 for MDC-1200 for TK-3173
Install & Program CIM-1000K-20 for GE-Star for TK-3173
170/173 Portable KCT-57MS Installation (for FleetSync®)
Page 3 of 3
75.00
75.00
20.00
20.00
TK-3173
March 2009
TK-2302VK / 3302UK
VHF/UHF Conventional Portable Radios
GENERAL FEATURES
• 5 W (136-174 MHz) VHF
• 4 W (450-490 MHz) UHF
• 16 Channels
• Single Priority / Normal Scan
• Transmit / Busy / Call Alert / Scan / Warn LED
• 2 PF Keys
• Companded Audio (per Ch. setting)
• VOX Ready (per Ch. setting)
• Voice Inversion Scrambler Built-in (per Ch. setting)
• QT / DQT
• Time Out Timer
• Low Battery Warning
• Battery Saver
FleetSync®
• Selective Call
• Li-ion Battery (KNB-45L)
• Fast Charger (KSC-35K)
• Antenna [KRA-26M (VHF)/27M (UHF)]
RADIO
TK-2302VK
TK-3302UK
LIST
136-174 MHz VHF 5W, 16 Ch.
284.00
300.00
450-490 MHz VHF 4W, 16 Ch.
ANTENNAS
KRA-16M
KRA-16M2
KRA-17M
KRA-22M
KRA-22M2
KRA-23M
KRA-26M
KRA-26M2
KRA-27M
LIST
VHF low profile antenna 148-162 MHz
UHF low profile antenna 450-490 MHz
KNB-45L
KNB-29N
KSC-35K
KSC-35E
KSC-31K
KSC-31E
13.70
13.70
13.70
13.70
13.70
13.70
14.00
14.00
14.00
LIST
2000 mAh, Li-ion battery - requires KSC-35K/E charger
1500 mAh, NiMH battery - requires KSC-31K/E charger
110 volt Fast rate single unit charger for KNB-45L Li-ion battery
110 volt Fast rate single unit charger for KNB-29N
Page 1 of 2
63.00
36.75
31.50
31.50
31.50
31.50
TK-2302V・3302U
March 2009
BATTERIES AND CHARGERS - CONT'D
KMB-25
KMB-28
LIST
Six Unit Charger Adapter for the KSC-23BK/28/31K/35K/37 chargers
Six Unit Charger Adapter for the KSC-23BK/28/31K/35K chargers
KBH-10
KLH-126
KWR-1
191.00
208.50
LIST
Nylon case for TK-*200/*202/*302 Series
Water resistant bag
8.35
14.70
29.85
LIST
KEP-2
KHS-1
KHS-10-BH
52.50
65.25
368.00
KHS-10-OH
336.00
KHS-7
KHS-7A
KHS-8BE
KHS-8BL
KHS-9BE
KHS-9BL
KHS-22
70.00
105.00
103.25
103.25
166.00
166.00
41.00
KHS-23
KHS-25
KHS-26
KHS-27
KMC-45
KMC-21
HMC-3
Headset w/PTT & VOX
55.50
24.50
28.00
24.50
86.00
51.50
63.00
LIST
Clip Mic w/earphone
KPG-22AM
KCT-53UM
KPG-119DK
Windows® Programming Software for TK-2302VK/3302UK
L-1626
191.00
86.00
103.25
LIST
TK-2302VK/3302UK Programming (with basic TX/RX check)
Page 2 of 2
37.50
TK-2302V・3302U
March 2009
TK-2212L / 3212L
All 212L series portables include:
• Antenna [KRA-26M (VHF)/27M (UHF)]
GENERAL FEATURES
• 5 W (136-174 MHz) Model
• 4 W (450-490, 470-512 MHz) Models
• Conventional Zones
• Backlit LCD
• 4 Front PF Keys
• 2 Side PF Keys
• Companded Audio
• VOX Ready
• QT / DQT
• Special Alert Tone Pattern
• Call Key
• Time Out Timer
• Battery Saver
• Wireless Cloning
• MIL-STD "Driven-Rain"
FleetSync®
• Short Text Message
RADIO
TK-2212LK
TK-3212LK
TK-3212LK2
LIST
136-174 MHz VHF 5W, 128 Ch.
333.00
350.00
350.00
450-490 MHz VHF 4W, 128 Ch.
470-512 MHz VHF 4W, 128 Ch.
ANTENNAS
KRA-16M
KRA-16M2
KRA-17M
KRA-22M
KRA-22M2
KRA-23M
KRA-26M
KRA-26M2
KRA-27M
LIST
KNB-45L
KNB-29N
KSC-35K
KSC-35E
KSC-31K
KSC-31E
13.70
13.70
13.70
13.70
13.70
13.70
14.00
14.00
14.00
LIST
Page 1 of 2
63.00
36.75
31.50
31.50
31.50
31.50
TK-2212L・3212L
March 2009
KMB-25
KMB-28
LIST
KBH-10
KWR-1
191.00
208.50
LIST
8.35
29.85
Water resistant bag
LIST
KEP-2
KHS-1
KHS-10-BH
52.50
65.25
368.00
KHS-10-OH
336.00
KHS-7
KHS-7A
KHS-8BE
KHS-8BL
KHS-9BE
KHS-9BL
KHS-22
70.00
105.00
103.25
103.25
166.00
166.00
41.00
KHS-23
KHS-25
KHS-26
KHS-27
KMC-45
KMC-21
HMC-3
Headset w/PTT & VOX
55.50
24.50
28.00
24.50
86.00
51.50
63.00
LIST
Clip Mic w/earphone
KPG-22AM
KCT-53UM
KPG-100DK
Windows® Programming Software for TK-2212L/3212L
L-991
191.00
86.00
103.25
LIST
TK-2212L/3212L Programming (with basic TX/RX check)
Page 2 of 2
37.50
TK-2212L・3212L
March 2009
ProTalk® TK-2200LP/3200LP
VHF / UHF BRS Portable Radios
All 200LP series portables include:
• Antenna (KRA-26M/27M)
GENERAL FEATURES
• 2 W (151-174 MHz) VHF
• 2 W (450-470 MHz) UHF
• 2, 8, & 15 Channels
• Normal Scan
• Super Lock
• Transmit / Busy / Call Alert
/ Scan / Warn LED
• 2 PF Keys
• Companded Audio
• Channel Confirmation Mode
• VOX Ready
• QT / DQT
• Time Out Timer
• Battery Saver
• Wireless Cloning
RADIO
TK-2200LV2P
TK-2200LV8P
TK-3200LU2P
TK-3200LU15P
LIST
151-159 MHz VHF 2W, 2 Ch.
151-159 MHz VHF 2W, 8 Ch.
461-470 MHz UHF 2W, 2 Ch.
461-470 MHz UHF 2W, 15 Ch. + SCAN
ANTENNAS
KRA-16M
KRA-17M
KRA-22M
KRA-23M
KRA-26M
KRA-27M
LIST
KNB-45L
KNB-29N
KSC-35K
KSC-35E
KSC-31K
KSC-31E
KMB-25
KMB-28
247.00
264.00
264.00
275.00
13.70
13.70
13.70
13.70
14.00
14.00
LIST
Page 1 of 2
63.00
36.75
31.50
31.50
31.50
31.50
191.00
208.50
TK-2200LP・3200LP
March 2009
KBH-10
KLH-126
KWR-1
LIST
8.35
14.70
29.85
Water resistant bag
LIST
KEP-2
KHS-1
KHS-10-BH
52.50
65.25
368.00
KHS-10-OH
336.00
KHS-7
KHS-7A
KHS-8BE
KHS-8BL
KHS-9BE
KHS-9BL
KHS-22
70.00
105.00
103.25
103.25
166.00
166.00
41.00
KHS-23
KHS-25
KHS-26
KHS-27
KMC-45
KMC-21
HMC-3
Headset w/PTT & VOX
55.50
24.50
28.00
24.50
86.00
51.50
63.00
LIST
KPG-22AM
KCT-53UM
Clip Mic w/earphone
191.00
86.00
KPG-88DK
*****************
C100569-19
C100569-2
C100693-19
C100693-2
C100733
C807027-05
C807028-05
KHS-8BE/9BE Replacement eartips, 10 per pack, beige (Recommended for sanitary purposes)
KHS-8BL/9BL Replacement eartips, 10 per pack, black
KHS-8BE/9BE Acoustic tube replacement kit, beige (Clear coiled tubing)
KHS-8BL/9BL Acoustic tube replacement kit, black
KHS-8/9 Noise attenuating kit, 1 set per pack (Foam ear tips pieces)
KHS-7 Foam mic windscreen, 5 pcs per pack
KHS-7 Foam ear cushion, 2 pcs per pack
Page 2 of 2
103.25
10.00
10.00
16.35
16.35
4.00
6.80
6.50
TK-2200LP・3200LP
March 2009
TK-2200L / 3200L
All 200L series portables include:
• Antenna (KRA-26M/27M)
GENERAL FEATURES
• 2 W (136-174 MHz) VHF
• 2 W (450-470 MHz) UHF
• 2, 8, & 15 Channels
• Transmit / Busy / Call Alert
/ Scan / Warn LED
• 2 PF Keys
• Companded Audio
• VOX Ready
• QT / DQT
• Time Out Timer
• Battery Saver
FleetSync®
• Selective Call
RADIO
TK-2200LK
TK-2200LK2
TK-3200LK
TK-3200LK3
LIST
250.00
267.00
267.00
289.00
150-174 MHz VHF 2W, 2 Ch.
150-174 MHz VHF 2W, 8 Ch.
450-470 MHz UHF 2W, 2 Ch.
450-470 MHz UHF 2W, 15 Ch.
ANTENNAS
KRA-16M
KRA-16M2
KRA-17M
KRA-22M
KRA-22M2
KRA-23M
KRA-26M
KRA-26M2
KRA-27M
LIST
KNB-45L
KNB-29N
KSC-35K
KSC-35E
KSC-31K
KSC-31E
KMB-25
KMB-28
13.70
13.70
13.70
13.70
13.70
13.70
14.00
14.00
14.00
LIST
Page 1 of 2
63.00
36.75
31.50
31.50
31.50
31.50
191.00
208.50
TK-2200L・3200L
March 2009
KBH-10
KLH-126
KWR-1
LIST
Water resistant bag
8.35
14.70
29.85
LIST
KEP-2
KHS-1
KHS-10-BH
52.50
65.25
368.00
KHS-10-OH
336.00
KHS-7
KHS-7A
KHS-8BE
KHS-8BL
KHS-9BE
KHS-9BL
KHS-22
70.00
105.00
103.25
103.25
166.00
166.00
41.00
KHS-23
KHS-25
KHS-26
KHS-27
KMC-45
KMC-21
HMC-3
Headset w/PTT & VOX
55.50
24.50
28.00
24.50
86.00
51.50
63.00
LIST
Clip Mic w/earphone
KPG-22AM
KCT-53UM
KPG-88DK
L-967
191.00
86.00
103.25
LIST
TK-2200L/3200L Programming (with basic TX/RX check)
Page 2 of 2
37.50
TK-2200L・3200L
March 2009
TK-2180 / 3180 MPT
VHF/UHF MPT 1327 Trunked Portable Radios
GENERAL FEATURES
• 5 W (136-174 MHz) Models
• 5 W (450-520, 400-470 MHz) Models
• Lighted Dot Matrix LCD
• Display Customization
• RSSI Indicator
• 2 Side PF Keys
• Encryption Board Control
• VGS-1 Voice Guide / Storage Option
• DTMF Manual Encode
• MIL-Spec Speaker Mic Option
• Front Panel Test/Tune
• Factory Mutual I.S. Option*
* Approved for Classes I, II & III, Div. 1, Groups C, D, E, F, G and are also approved for nonIncendive use in Class I, Div. 2, Groups A,B, C, D hazardous locations.
CONVENTIONAL MODE
• 32 Channels
• 12.5/25 kHz CH Spacing (per CH)
• QT / DQT Encode & Decode
• Normal Scan (No Priority)
• Scan Delete / Add
• Companded Audio (per CH)
• Time Out Timer
• Busy Channel Lockout (per CH)
TRUNKED MODE
• 8 Network Capacity
• Multi-Site Network Trunking
• Single-Site Trunking
• Network Roaming / Registration
• 12.5/25 kHz Spacing (per network)
• Individual Call ("Private Calling")
• Group Call
• Broadcast Call
• Inter-fleet Calling
• Inter-Prefix Calling
• PTT Intiate Call
• PSTN/PABX Call
• Priority Call
• Emergency Call
• Pre-emptive Emergency
• Full Off Air Call Setup
• Network Call Queuing
• Call Prioritization
• Queue Incoming Calls
• Electronic Serial Number (ESN)
• 250 Call and Group Address List
• Group Scan
• Home Address
• Direct Address
PACKAGES
LIST
Must Order MPT OPTION ( L-1012 )
L-1012
TK-2180K-NKP
TK-2180K-LKP
TK-2180K-AKP
TK-3180K-NKP
TK-3180K2-NKP
TK-3180K-LKP
TK-3180K2-LKP
TK-3180K-AKP
TK-3180K2-AKP
Install MPT option in 180-Series radio
VHF NiMH Battery Package (TK-2180K + KNB-32N + KSC-32 + KBH-11)
VHF Li-Ion Battery Package (TK-2180K + KNB-33L + KSC-32 + KBH-11)
VHF NiCd Battery Package (TK-2180K + KNB-31A + KSC-32 + KBH-11)
UHF NiMH Battery Package (TK-3180K + KNB-32N + KSC-32 + KBH-11)
UHF Li-Ion Battery Package (TK-3180K + KNB-33L + KSC-32 + KBH-11)
UHF NiCd Battery Package (TK-3180K + KNB-31A + KSC-32 + KBH-11)
UHF NiCd Battery Package (TK-3180K2 + KNB-31A + KSC-32 + KBH-11)
Page 1 of 4
16.67
700.50
718.00
683.00
717.50
717.50
735.00
735.00
700.00
700.00
TK-2180・3180 MPT
March 2009
RADIO
TK-2180K
TK-2180K2
TK-3180K
TK-3180K3
TK-3180K2
TK-3180K4
LIST
136-174 MHz 5W, 512 CH / 128 Zone CONV-& LTR
136-174 MHz 5W, 512 CH / 128 Zone CONV-& LTR with DTMF keypad
450-520 MHz 5W, 512 CH / 128 Zone CONV-& LTR with DTMF Keypad
543.00
595.00
560.00
613.00
560.00
613.00
LIST
TK-2180-ISK
TK-2180-ISK2
TK-3180-ISK
TK-3180-ISK3
TK-3180-ISK2
TK-3180-ISK4
543.00
595.00
560.00
613.00
560.00
613.00
ANTENNAS
KRA-26M
KRA-26M2
KRA-26M3
KRA-27M
KRA-27M2
KRA-27M3
KRA-22M
KRA-22M2
KRA-22M3
KRA-23M
KRA-23M2
KRA-23M3
KRA-25
KRA-28
LIST
14.00
14.00
14.00
14.00
14.00
14.00
13.70
13.70
13.70
13.70
13.70
13.70
34.25
42.00
KNB-31A
KNB-32N
KNB-33L
KNB-41NC
LIST
70.00
87.50
105.00
136.50
KNB-43L
KNB-49PL
163.00
84.00
KBP-6
68.50
Page 2 of 4
TK-2180・3180 MPT
March 2009
KSC-32
LIST
70.00
KSC-326K
KMB-30M
KMB-23
KVC-15
KVC-18
630.00
33.75
191.00
119.00
446.50
KBH-11
KBH-10
KBH-8DS
KLH-6SW
KLH-122
KLH-123
KLH-124
KLH-125
KLH-137ST
KWR-1
LIST
Low profile spring action belt clip (for use with KNB-33L Only)
Leather swivel belt loop / detachable swivel D-Ring back for KLH-122/123
Heavy duty leather carrying case for TK-2180/3180 (Non DTMF keypad models)
Heavy duty leather carrying case for TK-2180/3180 (DTMF keypad models)
Cordura Nylon carrying case for TK-2180/3180 (Non DTMF keypad models)
Cordura Nylon carrying case for TK-2180/3180 (DTMF keypad models)
Firemen's Heavy-Duty Leather Shoulder Strap for KLH-122/123
Water resistant bag
14.70
8.35
26.30
22.00
44.25
44.25
26.30
26.30
36.75
29.85
KEP-1
LIST
52.50
KCT-30
64.00
KEP-3
51.50
KEP-4
54.75
KMC-41M
96.50
KMC-42WM
114.00
standards
KHS-11BE
156.50
KHS-11BL
156.50
KHS-12BE
184.00
KHS-12BL
184.00
KHS-14
126.00
KHS-15-BH
420.00
KHS-15-OH
368.00
Page 3 of 4
TK-2180・3180 MPT
March 2009
OPTION MODULES
LIST
180-Series MPT radios/protocol do not support ANI Boards
KCT-57MS
22.00
Order L-1612 for MPT Emergency operations
VGS-1
87.50
LIST
KPG-36AM
KCT-53UM
KPG-96DK
Windows® Programming Software for 180-Series MPT
(Dealer Level License ID included)
93.00
86.00
103.25
Note: Must order L-1013 for Network Level License ID & programming privileges
LIST
L-961
L-962
L-963
L-994
L-1012
L-1013
L-1014
TK-2180/3180 Programming (with basic TX/RX check)
17.00
25.00
Note: VGS-1 installation precludes any ANI or encryption board installation
37.50
70.00
16.67
158.33
85.00
Configure TK-2180-IS/3180-IS for Intrinsically Safe
Network Level License ID for KPG-96D 180-Series Programmer
Retrofit Install of MPT option in 180-Seires radio
For previously purchased 180-Series radios. Order L-1014 through LMR order desk/rep. Ship radios to
attn: Kenwood LMR Tuning, Long Beach for installation. Include Kenwood order number for L-1014
provided by order desk & copy of company P.O. or P.O. number.
Note: Only certain Serial Number Lots produced in late 2004 and later can be retrofitted - see 180-Series
MPT Introduction Sales Bulletin for details
L-1612
Install KCT-57MS (for MPT Emergency Call)
Page 4 of 4
20.00
TK-2180・3180 MPT
March 2009
TK-2180 / 3180
VHF/UHF Trunking & Conventional Portable Radios
GENERAL FEATURES
• 5 W (136-174 MHz) Models
• 5 W (450-520, 400-470 MHz) Models
• RSSI Indicator
• 2 Side PF Keys
• Companded Audio
• VOX Ready
• Call Key
• Time Out Timer
• Battery Saver
* Approved for Classes I, II & III, Div. 1, Groups C, D, E, F, G and are also approved for nonIncendive use in Class I, Div. 2, Groups A,B, C, D hazardous locations.
PACKAGES
TK-2180K-NKP
TK-2180K-LKP
TK-2180K-AKP
TK-3180K-NKP
TK-3180K2-NKP
TK-3180K-LKP
TK-3180K2-LKP
TK-3180K-AKP
TK-3180K2-AKP
• Cloning
CONVENTIONAL ZONES
• QT / DQT
• Two-Tone Decode
• List Scan
TRUNKED ZONES
• 512 GID / 128 Zones
FleetSync®
LIST
VHF NiMH Battery Package (TK-2180K + KNB-32N + KSC-32 + KBH-11)
VHF Li-Ion Battery Package (TK-2180K + KNB-33L + KSC-32 + KBH-11)
VHF NiCd Battery Package (TK-2180K + KNB-31A + KSC-32 + KBH-11)
UHF NiMH Battery Package (TK-3180K + KNB-32N + KSC-32 + KBH-11)
UHF Li-Ion Battery Package (TK-3180K + KNB-33L + KSC-32 + KBH-11)
UHF NiCd Battery Package (TK-3180K + KNB-31A + KSC-32 + KBH-11)
UHF NiCd Battery Package (TK-3180K2 + KNB-31A + KSC-32 + KBH-11)
Page 1 of 4
700.50
718.00
683.00
717.50
717.50
735.00
735.00
700.00
700.00
TK-2180・3180
March 2009
RADIO
TK-2180K
TK-2180K2
TK-3180K
TK-3180K3
TK-3180K2
TK-3180K4
LIST
543.00
595.00
560.00
613.00
560.00
613.00
LIST
TK-2180-ISK
TK-2180-ISK2
TK-3180-ISK
TK-3180-ISK3
TK-3180-ISK2
TK-3180-ISK4
ANTENNAS
KRA-26M
KRA-26M2
KRA-26M3
KRA-27M
KRA-27M2
KRA-27M3
KRA-22M
KRA-22M2
KRA-22M3
KRA-23M
KRA-23M2
KRA-23M3
KRA-25
KRA-28
LIST
KNB-31A
KNB-32N
KNB-33L
KNB-41NC
543.00
595.00
560.00
613.00
560.00
613.00
14.00
14.00
14.00
14.00
14.00
14.00
13.70
13.70
13.70
13.70
13.70
13.70
34.25
42.00
LIST
70.00
87.50
105.00
136.50
KNB-43L
KNB-49PL
163.00
84.00
KBP-6
68.50
Page 2 of 4
TK-2180・3180
March 2009
KSC-32
LIST
70.00
KSC-326K
KMB-30M
KMB-23
KVC-15
KVC-18
KBH-11
KBH-10
KBH-8DS
KLH-6SW
KLH-122
KLH-123
KLH-124
KLH-125
KLH-137ST
KWR-1
119.00
446.50
LIST
Low profile spring action belt clip (for use with KNB-33L Only)
Water resistant bag
KMC-38GPS
630.00
33.75
191.00
14.70
8.35
26.30
22.00
44.25
44.25
26.30
26.30
36.75
29.85
LIST
GPS Speaker Microphone
402.50
KMC-41M
96.50
KMC-42WM
114.00
standards
KEP-1
52.50
KCT-30
64.00
KEP-3
51.50
KEP-4
54.75
KHS-11BE
156.50
KHS-11BL
156.50
KHS-12BE
184.00
KHS-12BL
184.00
KHS-14
126.00
KHS-15-BH
420.00
KHS-15-OH
368.00
Page 3 of 4
TK-2180・3180
March 2009
OPTION MODULES
KCT-48VU
LIST
49.00
KCT-57MS
22.00
CIM-1000K-26
131.25
the board).
CIM-CABLE
61.25
VGS-1
87.50
FRIMWARE OPTIONS
KWD-180MPT
LIST
MPT Trunking Field Upgrade Kit for 180-Series
43.75
Must order L-1619
Note: Refer to 180-Series MPT Price Pages and 180-Series MPT In-Depth Technical Manuals for feature
details (available from technical support). Not compatible with any other firmware options
Radio does not retain all normal 180-Series conventional or LTR trunking features once the MPT option is
installed.
KWD-180TFS
TFS-- Tactical Feature Set-- Field Upgrade Kit for 180-Series
105.00
Must order L-1624
Note: Refer to 180-Series “Tactical Feature Set” In-Depth Technical Manual for feature details (available
from technical support). Not compatible with any other firmware options.
LIST
KPG-36AM
KCT-53UM
KPG-89DK
L-961
L-962
93.00
86.00
103.25
LIST
17.00
25.00
L-963
L-994
Configure TK-2180-IS/3180-IS for Intrinsically Safe
37.50
70.00
L-1018
L-1019
L-1610
L-1611
L-1619
L-1624
180 Portable KCT-57MS Installation (for CIM-1000K-26)
180 Portable KCT-57MS Installation (for FleetSync®)
180 Portable KWD-180MPT FIELD-UPGRADE (Must purchase KWD-180MPT separately)
180 Portable KWD-180TFS FIELD-UPGRADE (Must purchase KWD-180TFS separately)
Page 4 of 4
75.00
75.00
20.00
20.00
NC
NC
TK-2180・3180
March 2009
TK-2170 / 3170
Compact VHF / UHF FM Portable Radios
GENERAL FEATURES
• 5 W (136-174 MHz) Models
• 4 W (450-490, 400-430 MHz) Models
• List Scan
• Backlit LCD
• 3 Side PF Keys
• 12-Key DTMF / PF Keypad Models
• Companded Audio
• VOX Ready
• Easy Option Port (20-Pin)
• QT / DQT
• Two-Tone Decode
• Call Key
• Time Out Timer
• Battery Saver
• Cloning
FleetSync®
--- Must Order L-1000 for Intrinsically Safe Option --* Approved for Classes I, II & III, Div. 1, Groups A, B, C, D, E, F, G and are also approved for nonIncendive use in Class I, Div. 2, Groups A, B, C, D hazardous locations.
PACKAGES
TK-2170K-AKP
TK-2170K-LKP
TK-3170K-AKP
TK-3170K-LKP
LIST
VHF Standard Package (TK-2170K + KNB-25A + KSC-30 + KRA-26M)
VHF Premium Package (TK-2170K + KNB-35L + KSC-25 + KRA-26M)
RADIO
TK-2170K
TK-2170K2
TK-3170K
TK-3170K4
TK-3170K3
TK-3170K6
446.25
524.00
463.25
541.00
LIST
Page 1 of 4
350.00
400.00
367.00
417.00
367.00
417.00
TK-2170・3170
March 2009
ANTENNAS
KRA-22M
KRA-22M2
KRA-22M3
KRA-23M
KRA-23M2
KRA-23M3
KRA-26M
KRA-26M2
KRA-26M3
KRA-27M
KRA-27M2
KRA-27M3
LIST
VHF Low -profile helical antenna 162-174 MHz
KBP-5
KNB-25A
KNB-26N
KNB-35L
KNB-40LC
13.70
13.70
13.70
13.70
13.70
13.70
14.00
14.00
14.00
14.00
14.00
14.00
LIST
49.00
50.75
70.00
98.00
112.00
KSC-25
KSC-25E
KSC-30
KSC-30E
KSC-256K
KMB-30M
KMB-16
KMB-23
KVC-3
KVC-4
included)
62.00
62.00
31.50
31.50
630.00
33.75
173.00
191.00
63.00
84.00
LIST
KLH-138
49.00
KLH-139
KBH-12
KBH-13DS
KWR-1
Heavy-Duty Leather Case w/Swivel Belt Loop for 170/173 (w/ DTMF keypad)
49.00
8.35
28.85
29.85
Water resistant bag
Page 2 of 4
TK-2170・3170
March 2009
KEP-2
LIST
52.50
KHS-1
65.25
KHS-10-BH
368.00
KHS-10-OH
336.00
KHS-7
70.00
KHS-7A
105.00
KHS-8BE
KHS-8BL
KHS-9BE
KHS-9BL
KHS-22
KHS-23
KHS-25
KHS-26
KHS-27
KMC-17
Clip Mic w/earphone
103.25
103.25
166.00
166.00
41.00
55.50
24.50
28.00
24.50
86.00
KMC-45
KMC-21
86.00
51.50
LIST
KPG-22AM
KCT-53UM
KPG-101DK
OPTION MODULES
KCT-57MS
191.00
86.00
103.25
LIST
22.00
CIM-1000K-20
131.25
[Intrinsically SafeApproved Accessory]- Must be Kenwood installed for I.S.
MDC-1200 or G-Star.
the board).
CIM-CABLE
61.25
Page 3 of 4
TK-2170・3170
March 2009
L-836
L-961
L-992
L-1000
LIST
Configure TK-2170/3170 for Intrinsically Safe
15.00
17.00
37.50
70.00
Must Order an I.S. Battery
L-1047
L-1048
L-1608
L-1609
Install & Program CIM-1000K-20 for MDC-1200 for TK-2170/3170
Install & Program CIM-1000K-20 for GE-Star for TK-2170/3170
170/173 Portable KCT-57MS Installation (for FleetSync®)
Page 4 of 4
75.00
75.00
20.00
20.00
TK-2170・3170
March 2009
TK-2160 / 3160
Compact VHF / UHF FM Portable Radios
• Belt Clip
GENERAL FEATURES
• 5 W (136-174 MHz)
• 4 W (450-490, 470-512, 400-430 MHz)
• 16 Conventional Channels
• Transmit / Busy / Call Alert / Scan / Warn LED
• 3 PF keys
• Companded Audio
• VOX Ready
• QT / DQT
• Two-Tone Decode
LIST
VHF Standard Package (TK-2160 + KNB-25A + KSC-30 + KRA-26M)
VHF Premium Package (TK-2160 + KNB-35L + KSC-25 + KRA-26M)
RADIO
TK-2160
TK-3160K
TK-3160K2
TK-3160K3
321.25
399.00
338.25
416.00
LIST
136-174 MHz 5W, Conventional 16 Channels
ANTENNAS
KRA-22M
KRA-22M2
KRA-22M3
KRA-23M
KRA-23M2
KRA-23M3
KRA-26M
KRA-26M2
KRA-26M3
FleetSync®
• Selective Call (single ID)
--- Must Order L-976 for Intrinsically Safe Option --* Approved for Classes I, II & III, Div. 1, Groups A, B, C, D, E, F, G and are also approved for nonIncendive use in Class I, Div. 2, Groups A,B, C, D hazardous locations.
PACKAGES
TK-2160SK-P
TK-2160RK-P
TK-3160SK-P
TK-3160RK-P
• Time Out Timer
• Battery Saver
225.00
242.00
242.00
242.00
LIST
VHF Low -profile helical antenna 162-174 MHz
Page 1 of 3
13.70
13.70
13.70
13.70
13.70
13.70
14.00
14.00
14.00
TK-2160・3160
March 2009
ANTENNAS - CONT'D
KRA-27M
KRA-27M2
KRA-27M3
LIST
14.00
14.00
14.00
KNB-25A
KNB-26N
KNB-35L
KNB-40LC
LIST
50.75
70.00
98.00
112.00
KBP-5
KSC-25
KSC-25E
KSC-30
KSC-30E
KSC-256K
KMB-30M
KMB-16
KMB-23
KVC-3
KVC-4
included)
49.00
62.00
62.00
31.50
31.50
630.00
33.75
173.00
191.00
63.00
84.00
LIST
KLH-138
49.00
KBH-12
KBH-13DS
KWR-1
8.35
28.85
29.85
Water resistant bag
KEP-2
LIST
52.50
KHS-1
65.25
KHS-10-BH
368.00
KHS-10-OH
336.00
KHS-7
70.00
KHS-7A
105.00
KHS-8BE
KHS-8BL
KHS-9BE
KHS-9BL
Page 2 of 3
103.25
103.25
166.00
166.00
TK-2160・3160
March 2009
KHS-22
KHS-23
KHS-25
KHS-26
KHS-27
KMC-17
Clip Mic w/earphone
LIST
41.00
55.50
24.50
28.00
24.50
86.00
KMC-45
KMC-21
86.00
51.50
LIST
KPG-22AM
KCT-53UM
KPG-82DK
Windows® Programming Software for TK-2160/3160
L-836
L-961
L-953
L-976
191.00
86.00
103.25
LIST
15.00
17.00
25.00
70.00
Page 3 of 3
TK-2160・3160
March 2009
TK-2140 / 3140
VHF/UHF Trunking / Conventional Compact Portable Radios
• Premiuam Warranty: 3 Years*
Order packages to include Antenna,
Battery & Charger,
or purchase Battery, Charger, and
Antenna separately.
GENERAL FEATURES
• 5 W (136-174 MHz)
• 4 W (450-490, 470-512, 400-430 MHz)
• 32 Conventional & LTR® Systems
• 2 Side PF Keys
• Companded Audio
• Time Out Timer
• Battery Saver
• Cloning
CONVENTIONAL SYSTEMS
• 250 Channels
• QT / DQT
• Two-Tone Decode
• Single & Multi-Group Scan
TRUNKED SYSTEMS
• 250 GID
FleetSync®
--- Must Order L-942 for Intrinsically Safe Option --* Approved for Classes I, II & III, Div. 1, Groups A, B, C, D, E, F, G hazardous locations and
Non-Incendive Class I, Div. 2, Groups A, B, C & D hazardous locations.
PACKAGES
TK-2140K-AKP
TK-2140K-LKP
TK-3140K-AKP
TK-3140K-LKP
LIST
VHF Standard Package (TK-2140 + KNB-25A + KSC-30 + KRA-26M)
VHF Premium Package (TK-2140 + KNB-35L + KSC-25 + KRA-26M)
RADIO
TK-2140
TK-3140K
TK-3140K2
TK-3140K3
LIST
136-174 MHz 5W, LTR-32 Systems, CONV-250 CH.
ANTENNAS
KRA-14M
KRA-14M2
KRA-14M3
KRA-15AM
KRA-15AM2
KRA-15AM3
689.25
767.00
707.25
785.00
593.00
611.00
611.00
611.00
LIST
17.80
17.80
17.80
17.80
17.80
17.80
Page 1 of 5
TK-2140・3140
March 2009
ANTENNAS - CONT'D
KRA-16M
KRA-16M2
KRA-16M3
KRA-17M
KRA-17M2
KRA-17M3
KRA-22M
KRA-22M2
KRA-22M3
KRA-23M
KRA-23M2
KRA-23M3
LIST
KBP-5
KNB-25A
KNB-26N
KNB-35L
KNB-40LC
13.70
13.70
13.70
13.70
13.70
13.70
13.70
13.70
13.70
13.70
13.70
13.70
LIST
49.00
50.75
70.00
98.00
112.00
KSC-25
KSC-25E
KSC-30
KSC-30E
KSC-256K
KMB-30M
KMB-16
KMB-23
KVC-3
KVC-4
included)
KBH-12
KBH-13DS
KLH-114
KLH-116
KWR-1
191.00
63.00
84.00
LIST
Soft leather case for TK-2140/3140
Heavy-Duty Leather Case w/Swivel Belt Loop for TK-2140/3140
Water resistant bag
KEP-1
62.00
62.00
31.50
31.50
630.00
33.75
173.00
8.35
28.85
44.25
49.00
29.85
LIST
52.50
KCT-30
64.00
KEP-3
51.50
KEP-4
54.75
KMC-25
96.50
Page 2 of 5
TK-2140・3140
March 2009
KMC-41M
KMC-42WM
LIST
96.50
114.00
standards
KHS-11BE
156.50
KHS-11BL
156.50
KHS-12BE
184.00
KHS-12BL
184.00
KHS-14
126.00
KHS-15-BH
420.00
KHS-15-OH
368.00
LIST
KPG-36AM
KCT-53UM
KPG-74DK
Windows® Programming Software for TK-2140/3140 portable
L-836
L-961
L-924
L-942
93.00
86.00
103.25
LIST
15.00
17.00
25.00
70.00
Page 3 of 5
TK-2140・3140
March 2009
FleetSync ® for TK-2140/3140 Series Portables
®
This radios firmware includes both FleetSync
purchasing the FleetSync Enhanced Option.
FleetSync
®
LIST
Basic and Enhanced feature sets. However, the "FleetSync® Enhanced" features must be "activated" in the radio by
Basic Features - "Basic" features are available in each radio as shipped from Kenwood (no actitvation is required). The entire Basic feature set is designed
®
to operate between other FleetSync capable base and fleet radios. Some Basic feature sets require a base dispatch PC application software and/or dispatch hardware
device for practical dispatch operations.
1) PTT ANI - digital ANI sent on each PTT using the FleetSync® ID.
2) Caller ID / Caller ID Stack- decodes an incoming PTT ID and displays the caller alphanumeric tag; Caller ID Stack stores the last 3 calls for review.
3) Selective Call - allows base-to-fleet and fleet-to-fleet selective calling via a pre-stored 100 ID list. Each ID can have an 16 character alphanumeric tag for easy selection
and Caller ID recognition.
4) Status Messaging - provides up to 50 pre-stored sixteen-character alphanumeric messages permitting a base to send a larger variety of job-type messages and fleet
radios to display and respond accordingly with complimentary acknowledgements. Iincludes special reserved statuses for: Emergency, Emergency Man-down, Emergency
Mode Off, Horn Alert (mobiles) and Radio Stun/Acknowledge/Resurrect statuses.
®
FleetSync Enhanced Option Features - The FleetSync® Enhanced Option must be "activated" in the radio at an extra charge by ordering labor code L-928 for a
Kenwood install or by ordering the appropriate quantities of L-925/926/927, SRB08698 and KPG-65ED dealer field retrofit options. This enables the following enhanced
features in addition to the Basic feature set:
5) PC Serial Control (mobiles only) - PC Serial Interface enables mobile COM port I/O serial data line for communications between an FleetSync®-capable mobile radio
and a FleetSync®-compatible PC application software or a peripheral device (e.g. KDS-100).
6) Short Text Messaging - decodes, stores and displays up to four 48-character Short Text messages
7) Long Text Messaging (mobiles only) - decodes and stores one 1024-character message for output to an external MDT or decode-display device.
8) FleetSync®-AVL (mobiles only) - embeds GPS NMEA information in FleetSync® data packets and sends them to a base/control station interfaced with a FleetSync®AVL compatible software.
To program all 140-Series radio parameters (including FleetSync ® parameters):
KPG-36AM
KCT-53UM
KPG-74DK
Windows® Programming Software for TK-2140/3140 portable
93.00
86.00
103.25
Kenwood Installed FleetSync ® Enhanced Option
L-928
FleetSync® Enhanced Option
50.00
Dealer Installed FleetSync® Enhanced Options
Note: Instead of L-928, options L-925/926/927; SRB08698 Hardware Key and KPG-65ED can be
purchased for dealer field installation of the FleetSync® Enhanced option
L-925
L-926
FleetSync® Enhanced Option (field retrofit) for 140-series; Price each for qty. 1-24
FleetSync® Enhanced Option (field retrofit) for 140-series; Price each for qty. 25-99
50.00
50.00
L-927
SRB08698
FleetSync® Enhanced Option (field retrofit) for 140-series; Price each for qty. 100+
Hardware Key
50.00
87.50
Note: SRB08698 hardware key holds also 100 ESN's maximum; multiple keys must be purchased for
orders over 100.
The SRB08698 hardware key requires L-925, 926, or 927 options to be loaded into it. The hardware key
requires the KPG-65ED to activate FleetSync® Enhanced Options in a 40-Series radio. The SRB08698
hardware key can be returned when empty for 50% credit. Call the LMR order desk for an RMA#. Credit
will NOT be issued for the L-925/926/927 options.
KPG-65EDK
FleetSync® Enhanced Option Installation Software
10.50
Note: Required for L-925/926/927 & SRB08698 use. This software is re-usable on future orders of L925/926/927
The KPG-65ED is a one-time order and may be re-used on future orders of L-925, 926, or 927. The
SRB08698 hardware key must be installed on the PC parallel port for the KPG-65ED to operate.
Page 4 of 5
TK-2140・3140
March 2009
PassPort ® for TK-2140/3140 Series Portables
LIST
PassPort ® Options for NEW Radio Orders (Kenwood-installed)
Ordering Instructions
For TK-2410/3140 new radio orders, the Kenwood-installed PassPort® ESN / firmware option is no charge: Order the PassPort® ESN/Firmware option L-971 for each
PassPort® radio.
Other required items:
KPG-98D Radio Programming Software: The KPG-98D programs PassPort®, LTR and Conventional modes. The KPG-98D is ONLY for programming a 140-Series
®
portable with the PassPort option installed and should NOT be used to program a standard LTR/Conventional 140-Series portable (use the KPG-74D).
KPG-98DK
L-971
PassPort® Programming software for TK-2140/3140 portables
Install PassPort® ESN option and firmware for new TK-2140/3140 orders
68.50
0.00
PassPort ® Options for Dealer/Operator Field Conversions (Field-installation kits)
1. Order the ESN key/firmware Labor Code options: L-892, L-893 or L-894; specify model radio(s).
Pre-loaded ESN hardware key(s) with the ordered quantities of ESN's and a PassPort® radio firmware diskette will be shipped (100 ESN’s maximum per hardware key).
Important: Any depleted key previously registered to a technicians computer must be retained to register any new purchased key to the computer; please retain the old key
until the new one is received.
2. Other required items:
a. KPG-64D PassPort® ESN Installation Software: This software is re-usable on subsequent orders of ESN hardware key options purchases.
b. KPG-98D Radio Programming Software: The KPG-98D programs PassPort®, LTR and Conventional modes. The KPG-98D is ONLY for programming a 140-Series
portable with the PassPort® option installed and should NOT be used to program a standard LTR/Conventional 140-Series portable (use the KPG-74D).
Note: Sales of L-892, 893, 894 are NOT refundable. Purchaser has a 72 hour limit after receipt to report
suspected hardware key defects or ESN shortages to Kenwood engineering, Suwanee office 678-4744700
L-892
L-893
L-894
SRB08698
PassPort® ESN Options & PassPort® firmware disk (SPECIFY RADIO MODEL)
· 1-24 qty. lot price; Price is per ESN
· 100 qty lot price; Price is per ESN
· Maximum 100 ESN options per hardware key
Hardware Key (Maximum 100 ESNs per hardware key) - requires KPG-64D to download
68.00
68.00
68.00
87.50
®
PassPort ESN options into an 80-Series radio.
Note: 1)The hardware key is registered to the computer that it is first used on; it cannot be used on other
computers. 2) Empty hardware keys can be returned for 50% credit; call the LMR order desk for RMA #. 3)
Retain depleted keys until a new one is received. It will be required to register the new key to the same
computer.
KPG-64DK
KPG-98DK
PassPort® ESN Field Installation Software
PassPort® Programming software for TK-2140/3140 portables
Page 5 of 5
10.50
68.50
TK-2140・3140
March 2009
TK-480 / 481
800/900 MHz FM Portable Radios
• Antenna
• Belt Clip
GENERAL FEATURES
• 2.5 W 800 MHz Models
• 2.5 W 900 MHz Models
• Trunked Format
• LTR® Trunked Systems
• Conventional Systems
• 32 Systems / 250 Groups
• System Scan
• List Type System Scan
• 2 Side PF Keys
• 12-Key DTMF/PF Keypad
• Companded Audio
• Time Out Timer
• Front Panel Test
• Cloning
• Intrinsically Safe Option
• NPSPAC Option
• QT / DQT
• Single Priority Group Scan
TRUNKED SYSTEMS
FleetSync®
• Short Text Messages (Option)
• PC Serial Interface (Option)
Purchase Battery & Charger separately
--- Must Order L-834 or L-980 for Intrinsically Safe Option --* Approved for Classes I, II, III Division 1, Groups C, D, E, F, G
and Non-Incendive Class I, Div. 2, Groups C, D hazardous locations.
RADIO
LIST
800 MHz
TK-480K3
TK-480K4
L-853
806-825, 851-870 MHz 2.5W, LTR-32 Systems, CONV-250 CH.
806-825, 851-870 MHz 2.5W, LTR-32 Systems, CONV-250 CH., with DTMF keypad
Install firmware & enable NPSPAC operation in TK-480
525.00
578.00
84.00
Note: Other required Items: KPG-49D V2.00 or higher permits "per channel" NSPAC programming
capability. NPSPAC and PassPort capabilty are not available in the same firmware option.
900 MHz
TK-481K3
TK-481K4
896-902, 935-941 MHz 2.5W, LTR-32 Systems, CONV-250 CH.
896-902, 935-941 MHz 2.5W, LTR-32 Systems, CONV-250 CH. with DTMF keypad
560.00
595.00
Important Note:
The TK-480/481/980/981 only operate in "Trunked Format" (LTR & Conventional systems). These are not
"Dual Format" radios like the TK-280/380/780/880 mobiles which operate in either Trunked Format (LTR &
Conventional systems) or Conventional Format (traditional conventional channel organization with priority
scan).
LTR ® is a registered trademark of E.F. Johnson Co.
ANTENNAS
LIST
*************** Call Kenwood Parts at 800-367-7514 to order the following (not available through the LMR Order Desk):
T90-0636-25
T90-0640-25
Replacement Part: 800 MHz Whip Antenna for TK-480
Replacement Part: 900 MHz Whip Antenna for TK-481
Page 1 of 4
31.04
31.98
TK-480・481
March 2009
KNB-16A
KNB-17A
KNB-17BK
LIST
59.50
70.00
105.00
KNB-21N
KNB-22N
KNB-22NC
63.00
73.50
122.50
KBP-4
KSC-19
KSC-19M
KSC-24
KSC-24E
KMB-16
KMB-23
KVC-3
KVC-4
KVC-5A
for KNB-14/15/16/17A/17B/20N/21N/22N/22NC
for KNB-14/15/16/17A/17B/20N/21N/22N/22NC
included)
KBH-10
KBH-8DS
KLH-58BC
KLH-6SW
KLH-75B
KLH-76B
KLH-85
KLH-86
KLH-92
KLH-137ST
KWR-1
62.00
173.00
191.00
63.00
84.00
357.00
LIST
Bungi-cord for KLH-58/60/71/75/76
Heavy duty leather carrying case for TK-480/481 (DTMF keypad models w/ KBP-4)
Water resistant bag
KEP-1
43.00
36.75
36.75
62.00
8.35
26.30
3.70
22.00
44.25
44.25
26.30
26.30
44.25
36.75
29.85
LIST
52.50
KCT-30
64.00
KEP-3
51.50
KEP-4
54.75
KMC-25
96.50
KMC-41M
KMC-42WM
96.50
114.00
standards
KHS-11BE
156.50
Page 2 of 4
TK-480・481
March 2009
KHS-11BL
LIST
156.50
KHS-12BE
184.00
KHS-12BL
184.00
KHS-14
126.00
KHS-15-BH
420.00
KHS-15-OH
368.00
OPTION MODULES
KCT-57MS
LIST
22.00
Order L-1618 FleetSync® operations
Note: CIM-1000 (MDC1200/GE STAR ANI encode board is not offered for sales loose or for TK-480/481
install. Dealers should purchase direct from Cimmarron Technologies 800-487-7184 at
www.cimtechcorp.com.
LIST
KPG-36AM
KCT-53UM
KPG-49DK
KPG-63DK
KPG-64DK
*****************
E30-3325-05
PassPort® Radio Programming Software V2.00 or higher
PassPort® ESN Field Installation Software
L-826
L-834
93.00
86.00
68.50
68.50
10.50
65.00
LIST
17.00
70.00
Must order KNB-17BK
L-980
70.00
Must order KNB-22NC
L-836
L-961
L-837
L-853
Assemble KMB-16 with six KSC-24's (Rapid Rate, 120 Volt version only)
15.00
17.00
0.00
84.00
Note: NPSPAC and PassPort capabilty are not available in the same firmware option.
L-876
L-877
L-878
L-892
L-893
L-894
L-1618
Install PassPort® ESN / Firmware Option (1-24 qty.)
Install PassPort® ESN / Firmware Option (25-99 qty.)
Install PassPort® ESN / Firmware Option (100 qty.)
PassPort® ESN & Firmware disk (1-24 qty.)
PassPort® ESN & Firmware disk (25-99 qty. )
PassPort® ESN & Firmware disk (100 qty.)
Page 3 of 4
68.00
68.00
68.00
68.00
68.00
68.00
20.00
TK-480・481
March 2009
LIST
PassPort® Options for NEW Radio Orders (Kenwood-installed)
For 800/900 MHz models TK-480/481/980/981 new radio orders, the Kenwood-installed Passport® ESN / firmware option is available for a charge: Order the
ESN/Firmware option per L-876, L-877 or L-878.
KPG-63D Radio Programming Software: the KPG-63D is required to program all PassPort® parameters for all PassPort® enabled radios, the KPG-63D will not program
LTR or conventional parameters. KPG-49D is required only if LTR or conventional systems are to also be programmed in the PassPort® radio.
KPG-63DK
L-876
L-877
Install PassPort® ESN options and firmware
· The latest PassPort® radio firmware will be installed
68.00
L-878
· 100 qty. lot price; Price is per ESN
68.00
Install PassPort® ESN options and firmware in TK-480/481/980/981
68.50
68.00
PassPort® Options for Dealer/Operator Field Conversions (Field-installation kits)
1. Order the ESN key/firmware Labor Code options: L-892 or L-894; specify model radio(s).
Pre-loaded ESN hardware key(s) with the ordered quantities of ESN's & a PassPort® radio firmware diskette will be shipped (100 ESN's maximum per hardware key).
Important: Any depleted key previously registered to a technicians computer must be retained to register any new purchased key to the computer; please retain the old
key until the new one is received.
a. KPG-64D: PassPort® ESN Install Program: the KPG-64D only needs to be ordered one time. It is re-useable for subsequent ESN orders (unless an upgrade is
recommended).
b. KPG-63D Radio Programming Software: required to program all PassPort® parameters for all PassPort® enabled radios, the KPG-63D will not program LTR or
conventional parameters.
c. KPG-49D Radio Programming Software: required only if LTR or conventional systems are also to be programming in the PassPort® radio.
3. The KPG-49D radio programming software is required for LTR & conventional site programming.
L-892
L-893
L-894
SRB08698
Hardware Key (Maximum 100 ESNs per hardware key)
68.00
68.00
68.00
87.50
®
- requires KPG-64D to download PassPort ESN options into an 80-Series radio.
computer.
KPG-64DK
PassPort® ESN Field Installation Software V1.12
10.50
· V1.12: supercedes V1.11; upgrade to V1.12 recommended for improved ESN file database features
KPG-63DK
Page 4 of 4
68.50
TK-480・481
March 2009
TK-290 / 390
VHF / UHF FM Transceivers
• Belt Clip
& Antenna Separately
GENERAL FEATURES
• 5 W (136-174 MHz)
• 4 W (403-430, 450-490, 470-512 MHz)
• 160 Channels / 16 Channel Groups
• QT / DQT
• Single & Multi-Group Scan
• Inverting LCD Display
• 2 Top Panel PF keys
• 2 Side PF Keys
• Orange Emergency / AUX Key (side)
• 2-Position PF Toggle Switch (top)
• 12-Key DTMF Keypad Models
• Companded Audio
--- Must Order L-1027 for MSHA Intrinsically Safe option --** MSHA Intrinsically Safe Models: Under U.S. CFR Title 30 Part 23, APPROVAL No. 23-A060002, the
TK-290/390 portable radios (with or without keypad models) are approved for intrinsically safety in methaneair mixtures only with only the Kenwood 7.2V KNB-44BK battery pack and the MSHA-certified listed
options/accessories. The battery pack should only be charged in fresh air
LIST
136-174 MHz 5W, 160 Ch. w/dual priority scan
136-174 MHz 5W, 160 Ch. w/dual priority scan, w/DTMF keypad
ANTENNAS
KRA-14M
KRA-14M2
KRA-14M3
KRA-15AM
KRA-15AM2
KRA-15AM3
KRA-16M
KRA-16M2
KRA-16M3
FleetSync®
--- Must Order L-835 or L-979 for Intrinsically Safe Option --* USTC (NFPA/NEC) Intrinsically Safe Models: Meets Intrinsically Safe Classes I, II & III, Div. 1, Groups
C, D, E, F, G hazardous locations and Non-Incendive Class I, Div. 2, Groups C, D hazardous locations.
RADIO
TK-290K
TK-290K2
TK-390K
TK-390K2
TK-390K3
TK-390K4
TK-390K6
• Two-Tone Decode
• Time Out Timer
• Battery Saver
• Cloning
• Intrinsically Safe Option (USTC)*
• MSHA Mine Safety
Intrinsically Safe Option**
788.00
840.00
840.00
840.00
840.00
893.00
893.00
LIST
17.80
17.80
17.80
17.80
17.80
17.80
13.70
13.70
13.70
Page 1 of 4
TK-290・390
March 2009
ANTENNAS - CONT'D
KRA-17M
KRA-17M2
KRA-17M3
KRA-22M
KRA-22M2
KRA-22M3
KRA-23M
KRA-23M2
KRA-23M3
KRA-26M
KRA-26M2
KRA-26M3
KRA-27M
KRA-27M2
KRA-27M3
KRA-25
LIST
VHF short helical antenna 148-162 MHz
UHF short whip antenna 450-490 MHz
KNB-16A
KNB-17A
KNB-17BK
13.70
13.70
13.70
13.70
13.70
13.70
13.70
13.70
13.70
14.00
14.00
14.00
14.00
14.00
14.00
34.25
LIST
59.50
70.00
105.00
KNB-21N
KNB-22N
KNB-22NC
63.00
73.50
122.50
KNB-44BK
1500 mAh, Ni-Cd battery - requires KSC-24 charger
114.00
[MSHA Intrinsically Safe Option]
KBP-4
KSC-19
KSC-19M
KSC-24
KSC-24E
KMB-16
KMB-23
KVC-3
KVC-4
KVC-5A
for KNB-14/15/16/17A/17B/20N/21N/22N/22NC
for KNB-14/15/16/17A/17B/20N/21N/22N/22NC
included)
KBH-10
KBH-8DS
KLH-6SW
KLH-78B
KLH-79B
43.00
36.75
36.75
62.00
62.00
173.00
191.00
63.00
84.00
357.00
LIST
Heavy duty leather carrying case for TK-290/390/5400 (DTMF keypad models)
Page 2 of 4
8.35
26.30
22.00
44.25
44.25
TK-290・390
March 2009
CARRYING ACCESSORIES - CONT'D
KLH-88
KLH-89
KLH-90
KLH-137ST
KLH-141
LIST
Cordura Nylon carrying case for TK-290/390/5400 (DTMF Keypad models)
for TK-290/390/5400 (DTMF keypad models w/ KBP-4)
Extra Heavy-Duty Cordura Nylon carrying case
for TK-190/290/390 (all battery packs; no keypad access)
KEP-1
26.30
26.30
44.25
36.75
34.75
LIST
52.50
KCT-30
64.00
KEP-3
51.50
[Intrinsically Safe Approved Accessory] [MSHA Approved Accessory]
KEP-4
54.75
KMC-25
96.50
KMC-41M
96.50
[MSHA Approved Accessory]
KMC-42WM
114.00
[MSHA Approved Accessory]
standards
KMC-26
MIL-SPEC, Noise canceling Speaker mic w/Antenna Connector (ant. not incl.)
115.50
KHS-11BE
156.50
KHS-11BL
156.50
KHS-12BE
184.00
KHS-12BL
184.00
KHS-14
126.00
KHS-15-BH
420.00
KHS-15-OH
368.00
OPTION MODULES
CIM-1000
LIST
131.25
board).
CIM-CABLE
61.25
Page 3 of 4
TK-290・390
March 2009
OPTION MODULES - CONT'D
KCT-57MS
LIST
22.00
KPG-36AM
KCT-53UM
LIST
KPG-38DK
*****************
E30-3325-05
L-804
L-836
L-961
L-835
93.00
86.00
68.50
65.00
LIST
Assemble KMB-16 with six KSC-24's
Configure TK-190/290/390 for USTC Intrinsically Safe
25.00
15.00
17.00
70.00
Must order KNB-17BK
L-979
Configure TK-190/290/390 for USTC Intrinsically Safe
70.00
Must order KNB-22NC
L-1027
Configure TK-290/390 for MSHA Intrinsically Safe
70.00
Must order KNB-44BK
L-837
L-870
L-1038
L-1039
L-1617
L-1618
90 PORTABLE KCT-57MS INSTALLATION (FOR CIM-1000)
Page 4 of 4
0.00
50.00
75.00
75.00
20.00
20.00
TK-290・390
March 2009
TK-272G / 372G
Compact Synthesized VHF / UHF FM Portable Radios
All 72G series portables include:
• Ni-Cd Battery (KNB-15ABK)
• Regular Rate Charger (SK Package)
or Rapid Rate Charger (RK Package)
• Belt Clip
GENERAL FEATURES
• 5 W (150-174 MHz)
• 4 W (450-470 MHz)
• 32 Channels
• QT / DQT
• Priority Scan
• 2 Side PF Keys
• 4 Front Panel PF Keys
• Companded Audio
• Two-Tone Encode/Decode
• Time Out Timer
• Battery Saver
• Windows® Programming & Tuning4
• Cloning
Purchase Antenna separately
PACKAGES
LIST
Regular Rate Charger Package
TK-272GK1SK
TK-272GK1SM
TK-372GK1SK
TK-372GK1SM
150-174 MHz 5W, 32 Ch., w/ 110V charger
325.00
325.00
325.00
325.00
Rapid Rate Charger Package
TK-272GK1RK
TK-272GK1RM
TK-372GK1RK
TK-372GK1RM
ANTENNAS
KRA-14M
KRA-14M2
KRA-15AM
KRA-16M
KRA-16M2
KRA-17M
LIST
17.80
17.80
17.80
13.70
13.70
13.70
KNB-14
KNB-15A
KNB-20N
KBP-1
KSC-15
KSC-15M
358.00
358.00
358.00
358.00
LIST
110 volt Regular rate single unit desk charger for KNB-14/15
220 volt Regular rate single unit desk charger for KNB-14/15
Page 1 of 3
38.50
49.00
49.00
21.00
29.40
29.40
TK-272G・372G
March 2009
KSC-24
KSC-24E
KMB-16
KMB-23
KVC-3
KVC-4
KVC-6A
LIST
for KNB-14/15/16/17A/17B/20N/21N/22N/22NC
for KNB-14/15/16/17A/17B/20N/21N/22N/22NC
included)
Vehicular D.C. Charger for 72G Series Portable with NiCd or NiMH Battery
KBH-10
KBH-8DS
KLH-6SW
KLH-112
KWR-1
62.00
62.00
173.00
191.00
63.00
84.00
357.00
LIST
Leather case for TK-272G/372G
Water resistant bag
8.35
26.30
22.00
44.25
29.85
LIST
KEP-2
KHS-1
KHS-10-BH
52.50
65.25
368.00
KHS-10-OH
336.00
KHS-7
KHS-7A
KHS-8BE
KHS-8BL
KHS-9BE
KHS-9BL
KHS-22
70.00
105.00
103.25
103.25
166.00
166.00
41.00
KHS-23
KHS-25
KHS-26
KHS-27
KMC-45
KMC-21
Clip Mic w/earphone
Page 2 of 3
55.50
24.50
28.00
24.50
86.00
51.50
TK-272G・372G
March 2009
KPG-22AM
KCT-53UM
LIST
KPG-56DK
Windows® Programming Software for 60G/70G/72G Portables & 60G/62G Mobiles
*****************
C807027-05
C807028-05
C100733
C100693-2
C100693-19
C100569-2
C100569-19
KHS-7 Foam mic windscreen, 5 pcs per pack
E05-0256-25
KHS-7 Foam ear cushion, 2 pcs per pack
KHS-8/9 Noise attenuating kit, 1 set per pack (Foam ear tips pieces)
KHS-8BL/9BL Acoustic tube replacement kit, black
KHS-8BE/9BE Acoustic tube replacement kit, beige (Clear coiled tubing)
KHS-8BL/9BL Replacement eartips, 10 per pack, black
KHS-8BE/9BE Replacement eartips, 10 per pack, beige (Recommended for sanitary
purposes)
Screw Mount-to-BNC Adapter
L-805
L-836
L-899
L-961
191.00
86.00
68.50
6.80
6.50
4.00
16.35
16.35
10.00
10.00
14.80
LIST
Install KNB-14/15A Battery
Assemble KMB-16 with six KSC-20's/KSC-24's
TK-272G/372G Programming (with basic TX/RX check)
Page 3 of 3
0.00
15.00
25.00
17.00
TK-272G・372G
March 2009
TK-5400
800 MHz Digital Project 25 / FM Portable Radio
5400 series portables include:
• Belt Clip
& Antenna Separately
GENERAL FEATURES
• 3 Watt (806-870 MHz)
• 16 Zones / 512 Channels
• Top Mounted LCD
• Electronic Inverting LCD Readout
• 2-Digit Numeric Sub-Display
• Function/Status LCD Icons
• 16-Position Mechanical Selector Knob
• 2-Position Programmable Toggle Switch
• 5 Programmable Function Keys
• Orange Emergency/AUX Key
• 12-Key DTMF/PF Keypad
• VOX Ready
• Time Out Timer
• Battery Saver
• Weather-Sealed Accessory Connector
• Scan Lists
FM
• QT / DQT
• DTMF Encode
• Companded Audio
P25 DIGITAL
• P25 Digital Trunking (included)
• IMBE TM VOCODER
• DES 16-Key Encryption Option
• Windows® DES Programming
--- Must Order L-970 or L-977 for Intrinsically Safe Option --* Approved for Classes I, II, III Division 1, Groups C, D, E, F, G
and Non-Incendive Class I, Div. 2, Groups C, D hazardous locations.
RADIO
TK-5400K
TK-5400K2
LIST
800 MHz P25 FDMA Digital / FM analog portable
800 MHz P25 FDMA Digital / FM analog portable with keypad
ANTENNA
KRA-24M
LIST
800 MHz Whip Antenna 1/4 wave end feed
KNB-17A
KNB-17BK
2,117.00
2,455.00
36.75
LIST
70.00
105.00
KNB-21N
KNB-22N
KNB-22NC
63.00
73.50
122.50
KBP-4
KSC-19
KSC-19M
Page 1 of 3
43.00
36.75
36.75
TK-5400
March 2009
KSC-24
KSC-24E
KMB-16
KMB-23
KVC-3
KVC-4
KVC-5A
LIST
for KNB-14/15/16/17A/17B/20N/21N/22N/22NC
for KNB-14/15/16/17A/17B/20N/21N/22N/22NC
included)
KBH-10
KBH-8DS
KLH-6SW
KLH-78B
KLH-79B
KLH-88
KLH-89
KLH-90
KLH-137ST
62.00
173.00
191.00
63.00
84.00
357.00
LIST
Heavy duty leather carrying case for TK-290/390/5400 (DTMF keypad models)
Cordura Nylon carrying case for TK-290/390/5400 (DTMF Keypad models)
for TK-290/390/5400 (DTMF keypad models w/ KBP-4)
KEP-1
62.00
8.35
26.30
22.00
44.25
44.25
26.30
26.30
44.25
36.75
LIST
52.50
KCT-30
64.00
KEP-3
51.50
KEP-4
54.75
KMC-25
96.50
KMC-41M
KMC-42WM
96.50
114.00
standards
KHS-11BE
156.50
KHS-11BL
156.50
KHS-12BE
184.00
KHS-12BL
184.00
KHS-14
126.00
KHS-15-BH
420.00
KHS-15-OH
368.00
Page 2 of 3
TK-5400
March 2009
LIST
KPG-36AM
KCT-53UM
KPG-78DK
Windows® Programming Software for TK-5400
(V3.00 or later)
Note: No DES encryption key loader An export license may be required (DOC/BIS ECCN 5D991)
KPG-78DTKL
Windows® Programming Software for TK-5400
(V2.02)
Note: Includes DES encryption key loader; An export license is likely required (DOC/BIS ECCN 5D002A)
KPG-93
TK-5210/5310/5400 KVL-3000/3000 Plus Interface Cable
FIRMWARE OPTIONS
KWD-DE10
93.00
86.00
628.00
628.00
262.50
LIST
TK-5400 DES-OFB Multi-key Encryption Option; 16 keys
578.00
Note: Must order L-995
U.S. DOC/BIS Export Controlled Item (ECCN 5A992A)
L-010
L-836
L-961
L-837
L-970
L-977
L-995
LIST
TK-5400 Programming (with basic TX/RX check)
Assemble KMB-16 with six KSC-20's/24's
Install KNB-17A/17BK/21N/22N/22NC battery
Configure TK-5400/KNB-22C for Intrinsically Safe (Must Order KNB-22NC)
Configure TK-5400/KNB-17BK for Intrinsically Safe
Install DES-OFB P25 Encryption Option
120.00
15.00
17.00
0.00
100.00
100.00
N/C
Note: Must purchase KWD-DE10 firmware option seperately
-- IMPORTANT NOTE -KWD-DE10 (DES-OFB) High Level Encryption Options and radios containing encryption are export controlled by the U.S. Department of Commerce Bureau of
Industry & Security EAR regulations and may either require an Export License, are eligible for a License Exception (ENC) or are exportable with No License Required
(NLR) depending on the country, the consignee and the intended use. High level encryption is a special commodity that may require an export license to most countries.
See www.bis.gov for more information regarding export regulations. DO NOT SHIP encryption items outside the U.S. without proper DOC/BIS Export Licenses and/or
compliances.
* Address:
* Contact Phone:
* Address:
* Contact Phone:
Page 3 of 3
TK-5400
Communications Sector
Systems Division Price List
LOW BAND
TKB-6900 Series Conventional Simplex Base Stations
29.7 - 50 MHz
GENERAL:
TKB-6900 Series Low Band Base Stations are built around the TK-690 high performance 110W radio. The TK-690 transceiver is
mounted in a 2 RU enclosure which includes forced air cooling and option bays for two peripheral circuit boards. The basic
configuration includes a 2 channel tone termination panel (2 or 4 wire audio). Equipment may be mounted in a cabinet enclosure or
open rack, and may be used either by itself (50W continuous duty or 110W at 20% duty cycle) or as a driver for an external continuous
duty RF amplifier (100W or 300W).
OPTIONS:
Power supply options include battery backup with integrated SmartCharger and Low Voltage Disconnect. Mounting options include
20 RU (42") and 40 RU (77") locking cabinets in addition to 17 RU (3') and 45 RU (7') open equipment racks. External connections are
RJ-11 for phone line, DB-25 for access to the internal chassis bus, & type N-female for RF. T-R simplex antenna switching is included in
the basic unit as well as in all external amplifiers. Other configurations are also available on a special order basis; please contact your
Kenwood Systems Regional Sales Manager for more details.
ORDERING INSTRUCTIONS:
Step 1: Determine the frequency sub-band:
K1 = 29.7 - 37.0MHz
Order TKB6900SK1 basic configuration
K2 = 35.0 - 43.0MHz
K3 = 39.0 - 50.0MHz
Step 2: Select an RF amplifier option.
Step 3: Select a power supply option.
Step 4: Select the desired mounting configuration.
Step 5: Select optional equipment or configuration changes.
Step 6: Add the basic configuration (Step 1) to the desired RF amplifier, power supply, mounting configuration and optional
equipment (Steps 2-5) to determine configuration pricing. Specify frequencies and tone assignments with order.
Page 1 of 5
Effective Date: March 01, 2009
Replaces Price List Dated November 15, 2008
LOW BAND
29.7 - 50 MHz
LIST
STEP 1 -- TKB-6900 BASIC CONFIGURATION:
TKB6900SK1 BASIC CONFIGURATION, 29.7 - 37.0MHz
$3,297
$3,297
$3,297
TKB-6900 low band base station basic configuration includes 40A DC power supply and 2 channel tone termination panel. Base station provides
50W continuous duty, 110W at 20% duty cycle. Includes factory tuning and staging, one service manual, and programming software; ships unmounted.
STEP 2 -- RF AMPLIFIER OPTIONS:
$2,171
OPTION KSGA110B: 100W CONTINUOUS DUTY RF AMPLIFIER UPGRADE
Upgrade to include external 100W continuous duty RF amplifier, 29.7-50.0MHz. Amplifier occupies 4 RU and is powered by the 40A, 13.8VDC
power supply included in the basic station configuration. Includes factory tuning, RF cables, wiring and internal T-R antenna relay.
$6,499
Upgrade to include external 300W continuous duty RF amplifier, 29.7-50.0MHz. Amplifier occupies 8 RU and is powered by a 70A, 13.8VDC power
supply. Includes factory tuning, RF cables, wiring and internal T-R antenna relay.
STEP 3 -- POWER SUPPLY OPTIONS:
-$83
OPTION KSGPWRX4: DELETE POWER SUPPLY
Delete power supply from basic station configuration or amplifier upgrade configuration.
OPTION KSGPWR34: UPGRADE FROM 40A TO 35A POWER SUPPLY WITH SMARTCHARGER
$881
For 100W amplifier option above, upgrade to 35A, 13.8VDC continuous duty switching power supply with front panel metering, built-in
SmartCharger, low-voltage disconnect, and solid state no-break transfer diodes. Occupies 2 RU, includes sealed fuse holder and fuses for battery
(battery not included). Gel cell batteries are available separately; please contact your Kenwood Systems Regional Sales Manager for details.
$881
OPTION KSGPWR74: UPGRADE FROM 40A TO 70A POWER SUPPLY
For 100W amplifier options above, upgrade to 70A, 13.8VDC continuous duty switching power supply with front panel metering; occupies 2 RU. Will
power up to 2 channels.
OPTION KSGPWRB4: UPGRADE FROM 40A TO 70A POWER SUPPLY WITH SMARTCHARGER
$1,263
OPTION KSGPWRH7: UPGRADE FROM 70A TO 70A POWER SUPPLY WITH SMARTCHARGER
$381
For 300W Amplifier option above, upgrade to 70A, 13.8VDC continuous duty switching power supply with front panel metering, built-in
STEP 4 -- MOUNTING CONFIGURATION:
$1,157
OPTION KSGMRCK3: 17 RU (3') ALUMINUM EQUIPMENT RACK
Standard 3' aluminum equipment rack providing 17 RU vertical mounting. Pricing includes equipment installation, hardware, cabling and wire
management materials, and cushioned shipping crate.
$1,250
Page 2 of 5
LOW BAND
29.7 - 50 MHz
LIST
$1,750
OPTION KSGMCAB2: 20 RU (42") LOCKING CABINET
Locking cabinet, 42"H x 22"W x 24"D, providing 20 RU vertical mounting, solid front door, louvered rear door, perforated top panel. Pricing
includes equipment installation, hardware, cabling and wire management materials, and cushioned shipping crate.
$2,659
$63
OPTION KSGMCABT: CABINET SOLID TOP UPGRADE
Cabinet upgrade to solid top panel; replaces standard perforated top panel.
$445
OPTION KSGMCABF: CABINET FAN TOP UPGRADE
Cabinet upgrade to solid top panel with 10" diameter 120VAC fan, replaces standard perforated top panel. Fan can be mounted above
panel or below; requires 2 RU clearance inside cabinet if mounted below panel (default position is below panel).
$93
OPTION KSGMCABB: CABINET INTERIOR SOLID FLOOR UPGRADE
Cabinet upgrade to add solid interior bottom panel inside cabinet, with 5 cable access openings (includes grommets and plugs).
STEP 5 -- OPTIONAL EQUIPMENT CONFIGURATIONS:
WIRELINE REMOTE CONTROL OPTIONS:
$393
OPTION KSGTN10B: 10 CHANNEL DISCRETE TONE TERMINATION PANEL UPGRADE
Upgrade to 10 channel (Discrete) tone termination panel, 2 or 4 wire, 600 Ohm balanced audio with monitor, installs in one station option bay.
$774
OPTION KSGTN16B: 16 CHANNEL BCD TONE TERMINATION PANEL UPGRADE
Upgrade to 16 channel (BCD) tone termination panel, 2 or 4 wire, 600 Ohm balanced audio with monitor, occupies 1 RU.
$0
OPTION KSGTDC2B: 2 CHANNEL DC TERMINATION PANEL OPTION
Replace 2 channel tone termination channel with 2 channel DC termination panel, 2 or 4 wire, 600 Ohm balanced audio with monitor, installs in one
station option bay. Specify required DC current settings at time of order.
$0
OPTION KSGTALD2: 600 Ohm BALANCED AUDIO LINE DRIVER & 4-WIRE E&M INTERFACE
Replace 2 channel tone termination channel with 1 channel receive audio line driver panel, 2 wire, 600 Ohm balanced output, installs in one station
option bay. May also be configured to fully support a 4-wire E&M interface application.
MISC STATION OPTIONS:
$8,840
OPTION KSGVOT1A: SIGNAL-TO-NOISE VOTER WITH ONE STATION MODULE
19" rack mount modular receiver voting comparator. Includes 1 station voter module for primary site (an additional station module is required for
each additional voted receiver site), occupies 3 RU.
$1,345
OPTION KSGVOT2A: ADDITIONAL STATION MODULE
Additional station voter module for signal-to-noise voting comparator. Occupies one card slot in KSGVOT1A chassis.
$855
OPTION KSGOPTG1: PILOT TONE GENERATOR AND LINE DRIVER
Internal pilot tone generator for use with voting systems, supplies 600 Ohm balanced 2 wire audio, installs in one station option bay.
Page 3 of 5
LOW BAND
29.7 - 50 MHz
LIST
$131
OPTION KSGOCWID: MORSE CODE IDENTIFIER
Internal automatic CWID Morse Code Identifier (addition to basic station), installs inside basic station enclosure. Specify call sign at time of order.
Includes programmer and cable.
$114.50
OPTION KPG-43AM: PROGRAMMING CABLE
OPTION KCT-53UM: DB9M TO USB TYPE A CONNECTOR
$86.00
OPTION B51-8460-10: TK-690 SERVICE MANUAL
$53.00
N/A
OPTION KPG-44DK: PROGRAMMING SOFTWARE
Note: Outdoor cabinets and other items are available by special order.
Please contact your Kenwood Systems Regional Sales Manager for more information.
Page 4 of 5
KENWOOD USA CORPORATION, COMMUNICATIONS SECTOR, SYSTEMS DIVISION
SYSTEM CONFIGURATION WORKSHEET
DEALER:
DLR #:
PHONE:
CONTACT:
FAX:
E-MAIL:
SHIP TO:
CITY:
ST:
PREPARED BY:
ZIP:
DATE:
REFERENCE PURCHASE ORDER NUMBER:
PAGE
OF
SYSTEM CONFIGURATION: Specify the primary system part number selected previously in Step 1 (e.g. TKR7400SK1, TKB8510PS, etc.); it
is not necessary to list the various system options already indicated on your Purchase Order. Also specify the transmit power level required at the
amplifier output (or exciter output, if being used without an external amplifier). Please Note : It is very important that your required transmit levels
be provided at time of order, since several of our amplifier models cannot be field-adjusted without voiding the product warranty. If applicable,
mark the box labeled "B" if the system will be used as a simplex, single-antenna base station, or mark "P" if it is intended for use in a transmit-only
paging application. For conventional systems using wireline remote control, indicate remote control type (Tone, DC, or Extended Local), desired
audio line levels (0dBm / 0dBm or +7dBm / -16dBm), and required circuit configuration (2-wire simplex or 4-wire full duplex).
PRODUCT CLASSIFICATION
TKR/TKB/KSG/NXR
CONFIGURATION
PRODUCT DESIGNATOR SUFFIX
WIRELINE REMOTE CONTROL
TRANSMIT POWER
-
CONTROL TYPE
W
B
AUDIO LEVELS
2W SIM / 4W DUP
/
P
RADIO INFORMATION: Specify the desired transmit and receive frequencies (include all four decimal places) for both Conventional and
Trunking systems in blocks of 5, indicating either Wideband or Narrowband for each channel (use additional sheets if necessary). For
Conventional channels, specify transmit and receive CTCSS frequencies (example: 131.8 Hz) or DCS codes (example: D732N) in the boxes
provided; or mark the CSQ box if the channel is Carrier Squelch only (no CTCSS or DCS).
TRANSMITTER
CHAN
W/N
CHAN 1 RX FREQ
TX CTCSS / DCS
CSQ
CHAN 2 RX FREQ
W/N
TX CTCSS / DCS
CSQ
CHAN 3 RX FREQ
.
RX CTCSS / DCS
CSQ
W/N
RX CTCSS / DCS
CSQ
W/N
RX CTCSS / DCS
CSQ
W/N
RX CTCSS / DCS
CSQ
W/N
RX CTCSS / DCS
CSQ
.
W/N
CHAN 4 TX FREQ
TX CTCSS / DCS
CSQ
CHAN 4 RX FREQ
.
.
CHAN 5 TX FREQ
W/N
TX CTCSS / DCS
CSQ
CHAN 5 RX FREQ
.
5
W/N
.
CHAN 3 TX FREQ
4
CHAN
CSQ
.
3
CHAN
TX CTCSS / DCS
.
CHAN 2 TX FREQ
2
CHAN
W/N
.
1
CHAN
RECEIVER
CHAN 1 TX FREQ
.
TRUNKING CONTROLLER INFORMATION (if applicable): For LTR Trunking systems, specify the model number of the controller to be
used on each channel and identify the sync master (1 per system). Also specify the LTR channel assignments for each controller, the Area Bit (0
or 1; all channels must match), the type of Telephone Interconnect (2W = 2-wire POTS, 4W = 4-wire E&M, DID = 4-wire Direct Inward Dialing),
whether RDD is to be set ON or OFF (VHF and UHF only), and the CWID to be used (if no CWID, check the NONE box). If the current firmware
revision is acceptable, mark the box provided; otherwise, specify the version needed. PassPort and MPT-1327 systems require special setup;
please contact Kenwood USA Corporation, Systems Division at 1-800-TRUNKING for more information.
CONTROLLER MODEL
CHAN
1
CHAN
2
CHAN
3
CHAN
4
CHAN
5
CONTROLLER
LTR CONTROLLER SETUP
FIRMWARE VERSION
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
KSG CONTROLLER
KSG CONTROLLER
KSG CONTROLLER
KSG CONTROLLER
KSG -
SPECIAL INSTRUCTIONS:
Yes
No
Is this system for resale? (check one)
Signature (required)
For more information, please contact your Kenwood representative.
Effective Date: November 1, 2008
March 2009
TK-7180 / 8180 MPT
VHF/UHF MPT1327 Trunked Mobile Radios
All 180 series mobiles include:
• Standard Microphone (KMC-35)
• Mounting Bracket
• DC Cable (KCT-23M)
• Blade Fuse
* TX Power is derated at 490-512 MHz
TK-8180K:
450-489 MHz (30 W)
490-512 MHz (25 W)
TK-8180HK: 450-489 MHz (45 W)
490-512 MHz (40 W)
GENERAL FEATURES
• 30W / 50W (136-174 MHz)
• 30W / 45W (450-520*, 400-470 MHz)
• Remote Control Head Option
• Display Customization
• RSSI Indicator
• 6 Backlit PF Keys
• Emergency / AUX Key
• 4 Watt Front Panel Speaker
• Encryption Board Control
• VGS-1 Voice Storage Option
• DTMF Manual Encode
• Timed Power Off
• DB-25 Accessory Connenctor
• 9 Programmable AUX I/Os
• 2 Programmable AUX Outputs
• Ignition Sense
• Mil-Spec Standard Mic
• MIL-Spec 12-Key DTMF Mic Option
CONVENTIONAL ZONES
• 32 Channels
• 12.5/25 kHz CH Spacing (per CH)
• QT / DQT Encode & Decode
• Normal Scan (No Priority)
• Scan Delete / Add
• Companded Audio (per CH)
• Time Out Timer
• Busy Channel Lockout (per CH)
TRUNKED ZONES
• 8 Network Capacity
• Multi-Site Network Trunking
• Single-Site Trunking
• Network Roaming/Registration
• 12.5/25 kHz Spacing (per network)
• Individual Call ("Private Calling")
• Group Call
• Broadcast Call
• Inter-fleet Calling
• Inter-Prefix Calling
• PTT Intiate Call
• PSTN/PABX Call
• Priority Call
• Emergency Call
• Pre-emptive Emergency
• Emergency Calling Features
• Full Off Air Call Setup
• Network Call Queuing
• Call Prioritization
• Third-Party Diversion
• Queue Incoming Call
• Special Alert Tone
• Manual Conventional Mode
• 250 Call and Group Address List
• Group Scan
• Home Address
• Direct Address
• Companded Audio
• Network Selector
• KAP-2 PA/Horn Alert Option
MODEL
LIST
Must Order MPT OPTION ( L-1012 )
L-1012
TK-7180K
TK-7180HK
TK-8180K
TK-8180HK
TK-8180K2
TK-8180HK2
16.67
586.00
718.00
604.00
735.00
604.00
735.00
MOBILE INSTALLATION ACCESSORIES
LIST
Horn Alert/P.A. Relay Option
63.00
KAP-2
Note: HA operates in MPT Trunked Mode only
KCT-46
KCT-40M
KCT-36
KLF-2
Ignition sense cable (plugs directly into mobile chassis ignition sense line)
KGP-2A/2B & KDS-100 Radio Interface Cable for TK-7150/8150/7180/8180.
Extension Cable for KCT-34/35/39/40M; 117.6 inches (9.8 ft)
Line Filter (suppresses alternator whine, 25dB, 25A max).
Page 1 of 2
13.70
29.00
43.75
42.00
TK-7180・8180 MPT
March 2009
TK-762G / 862G
VHF/UHF Conventional FM Mobile Radios
All 62G series mobiles include:
• Standard Microphone (KMC-27B)
GENERAL FEATURES
• 25 / 50 W (148-174 MHz) Models
• 25 W (450-490 MHz) Model
• 8 Channels / 8 Groups
• 1-Character / 7-Segment LCD
• Backlit LCD & Keys
• Transmit /Busy / Call Alert LED
• Top Panel Speaker
• Companded Audio
• QT / DQT
• Two-Tone Decode
• Single & Two-Tone Encode
• Call Key
• Top Panel Speaker
• Companded Audio
• QT / DQT
• Two-Tone Decode
• Call Key
MODEL
TK-762GK
TK-762HGK
TK-862GK
LIST
148-174 MHz 25W, 8 CH
429.00
473.00
481.00
148-174 MHz 50W, 8 CH
450-490 MHz 25W, 8 CH
CABLES
KCT-18
KCT-19
LIST
Ignition Sense Cable (Requires KCT-19)
Accessory Interface Cable (i.e., data, horn alert)
KAP-1
KLF-2
KMB-10
LIST
Horn Alert/P.A. Relay Option (Requires KCT-19)
Key lock adapter
CONTROL STATION INSTALLATION ACCESSORIES
KMC-9C
KMB-20
KPS-15
13.70
22.00
Control Station Desktop Microphone (8-pin mod. plug)
Control Station Mounting Case for KPS-15 Power Supplies
(mobile mounting hardware included)
DC Switching Power Supply (117/230 VAC; 23A max. continuous, 25A peak)
MICROPHONES AND SPEAKERS
42.00
42.00
26.30
LIST
86.00
26.30
173.00
LIST
KMC-27A
KMC-27B
KMC-28A
MIL-SPEC & Noise Canceling dynamic mobile microphone (8-pin mod. plug)
KMC-9C
KES-3
KES-5
Standard dynamic mobile microphone (8-pin mod. plug)
MIL-SPEC & Noise Canceling dynamic mobile microphone (8-pin mod. plug) w/ DTMF
External speaker (compact low profile; black case; 3.5 mm phono plug-in)
External Speaker, 40W max input, black case
104.00
42.00
163.00
86.00
44.25
61.25
Note: require a KCT-19 option
Page 1 of 3
TK-762G・862G
March 2009
FleetSync ® MOBILE DATA TERMINAL
KDS-100 Data Terminal includes:
• Mounting bracket
• Mounting hardware
• DC Cable
LIST
KDS-100 FEATURES
• Increases FleetSync® Message Viewing: 40 Character x 6 line Dot Matix LCD
- View 5 line Message List x 23 Char. @ line
(vs. 1 line Message x 16 Char. scrolling)
- View Short Text Messages (48 Char.) at once (vs. 48 Char. scrolling)
- View Long Text Message (1024 Char.) at once (vs. not available)
• Increases FleetSync® ID Capacity: 511 IDs (vs. 100 IDs)
- Base stations can handle larger size fleets
• Increases Status Message List Capacity: 89 Messages (vs. 50 Msgs.)
- More dispatcher-to-fleet type messages for different job tasks
- More fleet-to-dispatcher type messages for responses/statuses
• Increased Status Message Stack Memory: 367 Messages (vs. 9 Msg.s)
• Increased Short Text Message Stack Memory: 367 Messages (vs. 4 Msg.s)
• Litium Cell Memory Backup Battery (vs. radio-only volatile message memory)
• Large Backlit LCD & Function Keys
• Simple Installation
• Windows® Compatible Programming Software
• Programming Password Protection
• Built-in FleetSync® DSP Modem
• Real-Time Clock/Message Time Stamping
• 10 Status Message „Hot Keys‟
• Message Sorting & Deletion Screens
• Message Temporary Recycle Bin
• New Message Tone and LED Alerts
• Buzzer Volume Level
• Flashrom Firmeware Memory
Important Note:
1. KDS-100 Compatible Dispatch Software May Be Required - The KDS-100 used a fleet unit will
decode Status Messages and Selective Calls sent other FleetSync®-capable portables or mobiles, from a
KDS-100 with a FleetSync® capable mobile (PC mode) or a KDS-100 with a non-FleetSync® capable
mobile (air mode). However, Short and Long Text Messaging requires a base station FleetSync® capable
mobile PC Serial Interfaced with computer running a FleetSync® compatible dispatch software capable of
creating and sending Short/Long Text Messages. This software is available from vendors such as:
- IDA Corporation, Fargo ND: KenCall Dispatch software
- Kenwood Communications Corporation: Fleet Dispatch Pro software
2. The KDS-100 cannot be used simultaneously with a Kenwood KGP-2A/2B AVL unit.
KDS-100
FleetSync® Data Terminal
625.00
Note: The KDS-100 pigtail cable (1.83 ft) combined with the KDS-100 mobile interface cables KCT34/35/39/40M (1 ft.) and use a KCT-36 (9.8 ft.) for an extension.
KPG-71DK
KCT-35
KCT-36
Windows® Programming Software for KDS-100
Radio Interface Cable for KGP-2A/2B & KDS-100
103.25
22.00
43.75
AVL UNITS
LIST
KGP-2A/2B FEATURES
• Compatible Radios: 60G/62/63G/80/150/180/160-Series mobiles
• KGP-2A/2B air protocol is backward compatible with KGP-1A/1B
• Programmable Auto-reporting or polled updates
• 256 Mobile IDs x 256 Groups
• Mil-Spec 810C, D & E Dust, Vibration and Shock
• Over-the-air programming- Data Rate 1200 or 2400 baud
(except intial programming; see KPG-73D)
• Windows® 95, 98 & Me Programming Software (KPG-73D)
• Sixteen Multi-purpose Programmable I/O‟s [External Connectors; [DB-9 (ACC2); DB-15(ACC-3)]
- Each I/O programmable for either an analog “input” or output”
(dispatch-AVL mapping software must support)
- Inputs for external sensors, switches, contacts, etc.
- Outputs for external relays, controls, etc. (mapping software must support)
• LED Status Indicators
- DC Source- indicates receiving power from the mobile
- Data- indicates KGP-unit is sending /receiving data
- GPS- indicates receiving a GPS signal (KGP-2A)
• Flashrom Firmware / Compact Size
Page 2 of 3
TK-762G・862G
March 2009
AVL UNITS - CONT'D
LIST
Note: KGP-2A/2B Compatible AVL Mapping Software is Required
A KGP-2A/2B AVL system requires a AVL mapping software package “specifically engineered” for KGP®
protocol compatibility. Manning NavComp‟s RASTRAC software provides AVL mapping/fleet
management. To purchase, or for more information contact:
Manning NavComp, Inc.
4205 Park Dr.
Lago Vista, Texas 78645
Ph.: 512-267-7800, Fax: 512-267-9200
E-mail: [email protected]
Web: http://www.navcomp.com
FOR EACH BASE STATION ORDER:
1. KGP-2B Modem Unit - one KGP-Protocol base/control station modem unit required per AVL system
2. KCT-35 cable & L-930 - connects the KGP-2B to the 60G-Series base/control station mobile
3. Computer Serial Cable Required (not supplied)- The KGP-2B-to-PC COM Port connection for AVL data is made via a dealer-supplied computer serial communication
port cable. The serial cable should be a D-Sub 9-Pin Female (KGP-2B; ACC1 end) and the appropriate D-Sub 9-Pin or 25-Pin on the PC serial COM Port end. Serial
cables are wired "Null Modem" with pins 2-to-3 and 3-to-2 configured end connectors.
FOR EACH FLEET MOBILE ORDER:
1. KGP-2A GPS Receiver-Modem Unit - the KGP-Protocol fleet mobile unit
2. KCT-35 cable & L-930 - connects the KGP-2A to the fleet 60G-Series mobile
3. The KCT-19 & KCT-35 cannot be installed simultaneously- Therefore using a KCT-35 excludes plug-in of a KCT-19 for KES-5 external speaker (use KES-3), Horn Alert
output, Data modem I/O's, footswitch input and headsets.
KGP-2A
GPS Receiver / Modem Unit
551.00
(includes one dash-mount GPS antenna, mounting bracket, screw set)
1. One KCT-35 is required for each fleet and base mobile radio
2. L-930 - Install KCT-35 to 60G/62G/63G-Series Mobile for KGP-2A/2B interface
3. The KCT-35 is 12 inches in length; use a KCT-36 (9.8 ft.) extension if required
KGP-2B
Base Modem Unit
236.50
KCT-35
KCT-36
KPG-73DK
Windows® Programming Software for KGP-2A/2B
LIST
KPG-46AM
KCT-53UM
KPG-56DK
Windows® Programming Software for TK-762G/862G
L-136
L-895
L-897
L-930
22.00
43.75
103.25
191.00
86.00
68.50
LIST
60G/62G Mobile Programming (with basic TX/RX check)
Install KCT-19 in 60G/62G Series Mobiles for Data/MDT mode
Install KCT-19 in 60G/62G Series Mobiles for Emergency Foot Sw. Input
Install KCT-35 in 60G/62G/63G Series Mobiles for KDS-100/KGP-2A/2B Interface (order
KCT-35 seprately)
Page 3 of 3
20.00
17.00
17.00
21.00
TK-762G・862G
March 2009
TK-863G
UHF Trunking Mobile Radio
63G series mobile includes:
GENERAL FEATURES
• 25W, 450-490 MHz
• 32 Systems / 250 GID
• Inverting Front Panel
• Internal Speaker
• Companded Audio
• DTMF Encode
• Time Out Timer
• Accessory Interface Cable Option
• Ignition Sense
• Public Address / Horn Alert Option
• MIL-Spec Standard Mic Included
• MIL-Spec Noise-canceling Mic Option
• MIL-Spec 12-Key Noise-canceling Mic Option
• Windows Programming & Tuning
• Windows Firmware Uploading
• Cloning
• QT / DQT
TRUNKED SYSTEMS
MODEL
TK-863GK
LIST
465.00
450-490 MHz 25W, 32 Systems
CABLES
KCT-18
KCT-19
LIST
Ignition sense cable (Requires KCT-19)
Accessory connector cable (for ignition sense, horn alert, KSP- spkrs, & Data Port)
KAP-1
KLF-2
KMB-10
LIST
Horn Alert/P.A. Relay Option (requires KCT-19)
Line Filter (suppresses alternator whine, 25dB, 25A max)
Key Lock Adapter
KMC-9C
KMB-20
KPS-15
13.70
22.00
42.00
42.00
26.30
LIST
86.00
26.30
173.00
LIST
KMC-27A
KMC-27B
KMC-28A
KMC-9C
KES-3
KES-5
External Speaker, 40W max input, black case (TK-863G requires a KCT-19 option)
Page 1 of 3
104.00
42.00
163.00
86.00
44.25
61.25
TK-863G
March 2009
LIST
KDS-100 FEATURES
• DC Cable
Important Note:
KDS-100
625.00
KPG-71DK
KCT-35
KCT-36
103.25
22.00
43.75
AVL UNITS
LIST
KGP-2A/2B FEATURES
Page 2 of 3
TK-863G
March 2009
AVL UNITS - CONT'D
LIST
4205 Park Dr.
Ph.: 512-267-7800, Fax: 512-267-9200
2. KCT-35 cable & L-930 - connects the KGP-2B to the 60G-Series base/control station mobile
2. KCT-35 cable & L-930 - connects the KGP-2A to the fleet 60G-Series mobile
KGP-2A
551.00
KGP-2B
Base Modem Unit
236.50
KCT-35
KCT-36
KPG-73DK
LIST
KPG-46AM
KCT-53UM
KPG-76DK
Windows® Programming Software for TK-863G
L-895
L-897
L-930
L-936
22.00
43.75
103.25
191.00
86.00
103.25
LIST
Install KCT-19 in 60G/62G/63G Series Mobiles for Data/MDT mode
Install KCT-19 in 60G/62G/63G Series Mobiles for Emergency Foot Sw. Input
Install KCT-35 in 60G/62G/63G Series Mobiles for KDS-100/KGP-2A/2B Interface (order
KCT-35 separately)
TK-863G Programming (with basic TX/RX check)
Page 3 of 3
17.00
17.00
21.00
25.00
TK-863G
March 2009
MOBILE INSTALLATION ACCESSORIES - CONT'D
KMB-10
KRK-10
Key lock adapter
Remote Control Kit (a remote control cable (23 ft) is included)
LIST
26.30
105.00
LIST
KMC-9C
KMB-24
86.00
42.00
KPS-15
KMC-35
KMC-36
KMC-32
KMC-9C
KES-3
KES-5
173.00
LIST
Standard dynamic mobile microphone with DTMF keypad (8-pin mod. plug)
Low profile mobile microphone with 16 DTMF keypad (8-pin mod. plug)
External speaker, 40W max input
52.50
94.50
70.00
86.00
44.25
61.25
Note: requires KAP-2 (PA/HA unit) installed
OPTION MODULES
VGS-1
LIST
87.50
LIST
KPG-46AM
KCT-53UM
KPG-96DK
Windows® Programming Software for 180-Series MPT
(Dealer Level License ID included)
*****************
E30-3382-05
J29-0662-03
103.25
Note: Must order L-1013 for Network Level License ID & programming privileges
Clone cable
Mounting bracket for TK-7180/8180/7160/8160--same as supplied w/ radio (order N99-203905 for mounting screw set)
L-965
L-962
191.00
86.00
11.28
39.50
LIST
37.50
25.00
L-966
L-968
L-1012
L-1013
L-1014
Install KAP-2 (Default) HR1/Internal Sp./PA
Assemble TK-7180/8180 with KRK-10 Remote Kit
Network Level License ID for KPG-96D 180-Series Programmer
Retrofit Install of MPT option in 180-Seires radio
25.00
42.00
16.67
158.33
85.00
(for previously purchased 180-Series radios.)
Order L-1014 through LMR order desk/rep. Ship radios to attn: Kenwood LMR Tuning, Long Beach for
installation. Include Kenwood order number for L-1014 provided by order desk & copy of company P.O. or
P.O. number.
Note: Only certain Serial Number Lots produced in late 2004 and later can be retrofitted - see 180-Series
MPT Introduction Sales Bulletin for details
Page 2 of 2
TK-7180・8180 MPT
March 2009
TK-7180 / 8180
VHF/UHF Trunking & Conventional Mobile Radios
• Blade Fuse
TK-8180K:
450-489 MHz (30 W)
490-512 MHz (25 W)
TK-8180HK: 450-489 MHz (45 W)
490-512 MHz (40 W)
GENERAL FEATURES
• 30/50 W (136-174 MHz)
• 30/45 W (450-520*, 400-470 MHz)
• MPT1327 Trunking Option
• RSSI Indicator
• Front Panel Speaker
• Companded Audio
• Call Key
• Time Out Timer
• Timed Power Off
• DB-25 Accessory Connenctor
• Ignition Sense
• MIL-Spec Standard Mic
• Cloning
CONVENTIONAL ZONES
• QT / DQT
• Two-Tone Decode
• List Scan
TRUNKED ZONES
• 512 GID / 128 Zones
FleetSync®
• Short & Long Text Messages
• Input / Output Status Messages
• FleetSync® GPS Ready
• Send GPS PF Key
• Ignition On/Off GPS Reporting
MODEL
TK-7180K
TK-7180HK
TK-8180K
TK-8180HK
TK-8180K2
TK-8180HK2
LIST
586.00
718.00
604.00
735.00
604.00
735.00
LIST
63.00
13.70
29.00
43.75
42.00
26.30
105.00
KAP-2
KCT-46
KCT-40M
KCT-36
KLF-2
KMB-10
KRK-10
Key lock adapter
Page 1 of 5
TK-7180・8180
March 2009
KMC-9C
KMB-24
KPS-15
KMC-35
KMC-36
KMC-9C
KES-3
KES-5
LIST
86.00
42.00
173.00
LIST
52.50
94.50
86.00
44.25
61.25
• DC Cable
LIST
KDS-100 FEATURES
• Litium Cell Memory Backup Battery (vs. radio -only volatile message memory)
Important Note:
KDS-100
625.00
KPG-71DK
KCT-40M
KCT-36
Page 2 of 5
103.25
29.00
43.75
TK-7180・8180
March 2009
FleetSync ® MESSAGING
KAS-2FSD
LIST
FleetDispatchPRO: FleetSync® messaging dispatch software for PC
384.00
Note:
• TK-7180/8180 base mobile requires a DB-25 PC serial cable to connect to the base computer (purchase
aftermarket seperately).
• Supports FleetSync® PTT ID, Emergency, Status/Text Messaging for all FleetSync compatible portables
& mobiles.
• KDS-100 fleet units are compatible with the KAS-2FSD FleetSync calling & messaging features.
• Refer to KAS-2FSD spec sheet for detailed features & requirements
FleetSync ® AVL & MESSAGING
KGS-3
LIST
FleetSync® & NEXEDGETM AVL & Messaging Software (Windows® 2000/XP compatible),
347.00
Note: AVL operation /use is not required. Compatible with Microsoft®MapPoint®2004/2006 Software or
certain type imported maps (purchase aftermarket separately)
Refer to KGS-3 spec sheet for detailed features & requirements.
KAS-10
FleetSync® & NEXEDGETM AVL & Messaging Software (Windows® XP/VISTA compatible),
434.00
Refer to KAS-10 spec sheet for detailed features & requirements.
GPS15L-W
Garmin Internal GPS Receiver Board for FleetSync® AVL
130.25
Note:
• Conventional & LTR operation only
• Requires GA25 MCX GPS antenna
• Refer to 180/NX-Series & KGS-3 In-Depth Technical Manuals for installation, programming & KGS-3
software setup. Refer to www.garmin.com for GPS-15L-W technical specifications.
• Option: Order L-1033 for Kenwood Long Beach installation
GA25MCX
Garmin On-dash Style Magnetic base GPS Antenna for GPS15L-W
62.00
Note: shipped loose only; Install GA25MCX antenna to GPS15L-W before vehicle install; Refer to 180/NXSeries In-depth Technical Manuals for mobile installation.
AVL UNITS
LIST
KGP-2A/2B FEATURES
• Sixteen Multi-purpose Programmable I/O‟s [External Connectors; [DB-9 (ACC2); DB-15(ACC-3) ]
A KGP-2A/2B AVL system requires a AVL mapping software package “specifically engineered” for KGPprotocol compatibility. Manning NavComp‟s RASTRAC® software provides AVL mapping/fleet
4205 Park Dr.
Ph.: 512-267-7800, Fax: 512-267-9200
Page 3 of 5
TK-7180・8180
March 2009
AVL UNITS - CONT'D
LIST
2. KCT-40M cable- connects the KGP-2B to the base 180/150-Series mobile
2. KCT-40M cable- connects the KGP-2A to the fleet 180/150-Series mobile
KGP-2A
551.00
1. One KCT-40M is required for each fleet and base mobile radio
2. The KCT-40M is 12 inches in length; use a KCT-36 (9.8 ft.) extension if required
KGP-2B
Base Modem Unit
236.50
2. The KCT- 40M is 12 inches in length; use a KCT-36 (9.8 ft.) extension if required
KCT-40M
KCT-36
KPG-73DK
OPTION MODULES
VGS-1
CIM-1000K-26
29.00
43.75
103.25
LIST
87.50
131.25
Must order L-1020 or L-1021 for radio install & programming
the board).
CIM-CABLE
61.25
FRIMWARE OPTIONS
KWD-180MPT
LIST
MPT Trunking Field Upgrade Kit for 180-Series
43.75
Must order L-1620
Note: Refer to 180-Series MPT Price Pages and 180-Series MPT In-Depth Technical Manuals for feature
details (available from technical support). Not compatible with any other firmware options
Radio does not retain all normal 180-Series conventional or LTR trunking features once the MPT option is
installed.
KWD-180TFS
TFS-- Tactical Feature Set-- Field Upgrade Kit for 180-Series
105.00
Must order L-1625
Note: Refer to 180-Series “Tactical Feature Set” In-Depth Technical Manual for feature details (available
from technical support). Not compatible with any other firmware options.
Page 4 of 5
TK-7180・8180
March 2009
KPG-46AM
KCT-53UM
LIST
KPG-89DK
*****************
E30-3382-05
J29-0662-03
Clone cable
L-962
191.00
86.00
103.25
11.28
39.50
LIST
25.00
L-965
L-966
L-968
L-1010
L-1020
L-1021
L-1033
Install KAP-2 (External Sp.) HR1/External Sp./PA
Install Garmin GPS15L-W in 180-Series mobile for FleetSync® AVL
37.50
25.00
42.00
25.00
75.00
75.00
100.00
Note: The KGS-3 & GPS15L-W are not compatible with KGP-2A/2B AVL systems
L-1620
L-1625
NC
NC
180 Portable KWD-180MPT FIELD-UPGRADE (Must purchase KWD-180MPT separately)
180 Portable KWD-180TFS FIELD-UPGRADE (Must purchase KWD-180TFS separately)
Page 5 of 5
TK-7180・8180
March 2009
TK-7160 / 8160
VHF/UHF Conventional Mobile Radios
• 15A (HK) or 10A (K) Fuse
GENERAL FEATURES
• 25 / 50 W (136-174 MHz) Models
• 25 / 45 W (450-490 MHz) Models
• Single / Multi-Zone Scan
• Transmit /Busy / Call Alert LED
• Companded Audio
• QT / DQT
• Two-Tone Decode
• Call Key
• Time Out Timer
• Timed Power Off
• 8 Programmable I/O Ports
• Ignition Sense
• Front Panel Field-Program Mode
• Cloning
FleetSync®
• Input / Output Status Messages
• Send GPS PF Key
MODEL
TK-7160K
TK-7160HK
TK-8160K
TK-8160HK
LIST
136-174 MHz 25W, 128 CH / 128 Zone Conventional
467.00
533.00
483.00
550.00
LIST
63.00
13.70
22.00
43.75
42.00
26.30
KAP-2
KCT-18
KCT-39
KCT-36
KLF-2
KMB-10
Ignition sense cable (requires KCT-39 Acc. Cable Option)
Key lock adapter
KMC-9C
KMB-24
KPS-15
Control Station Mounting Case for KPS-15 Power Supplies for 180/160-series mobiles.
Page 1 of 4
LIST
86.00
42.00
173.00
TK-7160・8160
March 2009
KMC-35
KMC-36
KMC-9C
KES-3
KES-5
LIST
52.50
94.50
86.00
44.25
61.25
• DC Cable
LIST
KDS-100 FEATURES
Important Note:
KDS-100
625.00
KPG-71DK
KCT-39
KCT-36
Page 2 of 4
103.25
22.00
43.75
TK-7160・8160
March 2009
AVL UNITS
LIST
KGP-2A/2B FEATURES
4205 Park Dr.
Ph.: 512-267-7800, Fax: 512-267-9200
2. KCT-39 cable & L-xxx - connects the KGP-2B to the 160-Series base/control station mobile
2. KCT-39 cable - connects the KGP-2A to the fleet 160-Series mobile
KGP-2A
551.00
KGP-2B
Base Modem Unit
236.50
KCT-39
KCT-36
KPG-73DK
Page 3 of 4
22.00
43.75
103.25
TK-7160・8160
March 2009
OPTION MODULES
CIM-1000K-20
LIST
131.25
MDC-1200 or G-Star.
the board).
CIM-CABLE
61.25
KPG-46AM
KCT-53UM
LIST
KPG-99DK
*****************
E30-3382-05
J29-0662-03
Clone cable
L-985
L-966
L-1010
L-1057
L-1058
191.00
86.00
103.25
11.28
39.50
LIST
Install KAP-2 (External Sp.) HR1/External Sp./PA
TK-7160/8160 CIM-1000K-20/MDC1200 ENCODER INSTALLATION
TK-7160/8160 CIM-1000K-20/GE STAR ENCODER INSTALLATION
Page 4 of 4
37.50
25.00
25.00
75.00
75.00
TK-7160・8160
March 2009
TK-7150 / 8150
VHF/UHF Trunking & Conventional Mobile Radios
• Key kabel inserts
• Blade Fuse
GENERAL FEATURES
• 50 W (136-174 MHz)
• 45 W (450-500 MHz)
• Transmit & Receive LEDS
• Rotary Selector Knob
• Rotary Volume Knob
• 6 PF Keys with Labels
• 3.5 W Front Panel Speaker
• 13 W External Speaker Output
• Companded Audio
• Encryption & ANI Board Control
• Time Out Timer
• Timed Power Off
• DB-25 Accessory Connector
• Ext. Speaker, PA, Ignition Connector
• Ignition Sense
• Public Address/Horn Alert Output
• MIL-Spec / Noise-Cancel Mic Opt.
• MIL-Spec / Noise Cancel DTMF Mic Opt.
• Cloning
CONVENTIONAL ZONES
• QT / DQT
• Two-Tone Decode
• List Scan
TRUNKED ZONES
• 250 GID / 32 Zones
FleetSync®
• Short & Long Text Messages
• Send GPS PF Key
MODEL
TK-7150
TK-8150
LIST
136-174 MHz, 50 W, 128 Conventional/ 32 LTR Zones max.
450-500 MHz, 45 W, 128 Conventional/ 32 LTR Zones max.
KCT-18
KCT-22M
KCT-22M2
KCT-22M3
KCT-23M
KCT-23M3
KCT-36
KCT-40M
KLF-2
KRK-9
735.00
770.00
LIST
Ignition sense cable (plugs into TK-7150/8150 mobile 6-pin acc.conn.)
Remote Control Cable - 8 Feet; TK-7150/8150; 90-Series
Remote Control Cable - 17 Feet (typical sedan length); TK-7150/8150; 90-Series
Remote Control Cable - 25 Feet; TK-7150/8150; 90-Series
DC Cable (10-50W Dash mount)
DC Cable (10-50W Remote mount)
Remote Control Kit for TK-7150/8150
13.70
73.50
84.00
94.50
31.50
34.75
43.75
29.00
42.00
49.00
Note: purchase KCT-22M/M2/M3 cable separately
Page 1 of 4
TK-7150・8150
March 2009
LIST
Note: FleetSync® PC Serial Interface connections to a computer can be made with a standard computer
serial cable; DB-25 male (mobile) -to- DB-9/25 female (computer). The TK-7150/8150 does not require a
special Kenwood KCT-cable.
KMC-9C
KPS-15
86.00
173.00
LIST
KMC-27A
KMC-27B
KMC-28A
KMC-9C
KES-5
Ext. speaker, 40W max input; blk,. case, 5"x5"x2-9/16"
104.00
42.00
163.00
86.00
61.25
Note: plugs into 7150/8150 6-pin molex acc. conn.
• DC Cable
LIST
KDS-100 FEATURES
• Litium Cell Memory Backup Battery (vs. radio -only volatile message memory)
Important Note:
KDS-100
625.00
KPG-71DK
KCT-40M
KCT-36
Page 2 of 4
103.25
29.00
43.75
TK-7150・8150
March 2009
KAS-2FSD
LIST
384.00
Note:
• TK-7150/8150 base mobile requires a DB-25 PC serial cable to connect to the base computer (purchase
aftermarket seperately).
& mobiles.
AVL UNITS
LIST
KGP-2A/2B FEATURES
• KGP-2A/2B air protocol is backward compatible with KGP -1A/1B
(except intial programming; see KPG -73D)
• Windows® 95, 98 & Me Programming Software (KPG -73D)
• Sixteen Multi-purpose Programmable I/O‟s [External Connectors; [DB -9 (ACC2); DB-15(ACC-3) ]
- GPS- indicates receiving a GPS signal (KGP -2A)
4205 Park Dr.
Ph.: 512-267-7800, Fax: 512-267-9200
2. KCT-40M cable- connects the KGP-2B to the base 180/150-Series mobile
2. KCT-40M cable- connects the KGP-2A to the fleet 180/150-Series mobile
KGP-2A
551.00
2. The KCT-40M is 12 inches in length; use a KCT-36 (9.8 ft.) extension if required
KGP-2B
Base Modem Unit
236.50
2. The KCT- 40M is 12 inches in length; use a KCT-36 (9.8 ft.) extension if required
KCT-40M
KCT-36
KPG-73DK
Page 3 of 4
29.00
43.75
103.25
TK-7150・8150
March 2009
OPTION MODULES
CIM-1000
LIST
131.25
board).
CIM-CABLE
61.25
LIST
KPG-46AM
KCT-53UM
KPG-79DK
*****************
E30-3382-05
J29-0697-XX
Clone cable
Mounting bracket for TK-7150/8150 (hardware N99-0395-x5)- same as supplied with radio
L-939
L-940
L-1034
L-1035
191.00
86.00
103.25
11.28
TBD
LIST
TK-7150/8150 CIM-1000/MDC1200 ENCODER INSTALLATION
TK-7150/8150 CIM-1000/GE STAR ENCODER INSTALLATION
Page 4 of 4
50.00
35.00
75.00
75.00
TK-7150・8150
March 2009
TK-7102H / 8102H
VHF/UHF Conventional Mobile Radios
All 7102H/8102H mobiles include:
• DC Cable
• Fuse
GENERAL FEATURES
• 50 W (146-174, 136-162 MHz) Models
• 45 W (450-490, 485-512, 400-430 MHz) Models
• 8 Channels (4 Channels per Group)
• 2 Conventional Groups
• Normal Scan (no priority)
• Backlit Keys
• Channel /Transmit /Busy LEDs
• 4 Channel Keys
• 2 Function Keys
• Up/Down Volume Keys
• QT / DQT
• Time Out Timer
• 8 Programmable I/O Ports
• Ignition Sense
• Horn Alert Output
• 16-Key DTMF Mic Option
• Cloning
FleetSync®
MODEL
TK-7102HK
TK-7102HK2
TK-8102HK
TK-8102HK2
TK-8102HK3
LIST
146-174 MHz 50W, 4 CH x 2 Banks Conventional
KCT-18
KCT-39
KCT-36
KLF-2
KMB-10
LIST
Ignition sense cable (requires KCT-39 Acc. Cable Option)
Key lock adapter
KMC-9C
KMB-24
KPS-15
Control Station Mounting Case for KPS-15 Power Supplies. (mobile mounting hardware
included)
KMC-30
KMC-35
KMC-32
KMC-36
KMC-9C
KES-3
KES-5
350.00
350.00
367.00
367.00
367.00
13.70
22.00
43.75
42.00
26.30
LIST
86.00
42.00
173.00
LIST
Standard mobile microphone (8-pin mod. plug)
MIL-SPEC dynamic mobile microphone (8-pin mod. plug)
Standard mobile microphone with 16-key DTMF (8-pin mod. plug)
MIL-SPEC dynamic mobile microphone with 12-key DTMF keypad (8-pin mod. plug)
External Speaker, 40W max input, black case
31.50
52.50
70.00
94.50
86.00
44.25
61.25
Note: require a KCT-19 option
Page 1 of 3
TK-7102H・8102H
March 2009
KPG-46AM
KCT-53UM
LIST
191.00
86.00
®
KPG-70DK
Windows
*****************
E30-3382-05
J29-0662-03
Clone cable
103.25
Programming Software for TK-7102H/8102H
11.28
39.50
Mounting bracket for --same as supplied w/ radio (order N99-2039-05 for mounting screw
set)
LIST
TK-7102H/8102H Programming (with basic TX/RX check)
L-934
37.50
• DC Cable
LIST
KDS-100 FEATURES
Important Note:
KDS-100
625.00
KPG-71DK
KCT-39
KCT-36
®
Windows Programming Software for KDS-100
Page 2 of 3
103.25
22.00
43.75
TK-7102H・8102H
March 2009
AVL UNITS
LIST
KGP-2A/2B FEATURES
• Compatible Radios: 60G/62/63G/80/150/180/160-Series & 7102H/8102H mobiles
4205 Park Dr.
Ph.: 512-267-7800, Fax: 512-267-9200
2. KCT-39 cable & L-xxx - connects the KGP-2B to the 160-Series & 7102H/8102H base/control station mobile
2. KCT-39 cable - connects the KGP-2A to the fleet 160-Series & 7102H/8102H mobile
KGP-2A
551.00
KGP-2B
Base Modem Unit
236.50
KCT-39
KCT-36
KPG-73DK
Windows
®
Programming Software for KGP-2A/2B
Page 3 of 3
22.00
43.75
103.25
TK-7102H・8102H
March 2009
TK-6110
Compact Low Band Mobile Radio
GENERAL FEATURES
• 70 W (29.7-37.0, 35.0-50.0 MHz)
• 32 Channels
• 8 Character Alphanumeric LCD
• 3 Digit Sub-Display and Icons
• Transmit / Busy / Call Allert / Warn LED
• Up/Down Channel Selector
• Volume Knob
• Power On/Off Button
• 7 Programmable Radio Keys
• Noise Blanker Function
• QT/DQT Encode & Decode
• Two Tone Decode
• DTMF Encode & Decode
• Time Out Timer
• 15 Pin Accessory Connector
• MIL-Spec / Noise-Cancel Microphone
• M-Type Antenna Connector
• Ignition Sense
• Timed Power Off
• Horn Alert
• Cloning
• PC Programming & Tuning
• MIL-STD-810 C/ D/ E
IMPORTANT NOTICE [Power/Bandwidth vs. VSWR]
1. The TK-6110 mobiles output power will be significantly reduced with VSWR = 1.5 or greater.
TK-6110 Output Power Performance (nominal; transmission line losses not included)
VSWR
1.2 or less
1.3-1.5
More than 1.5
TK-6110K
Frequency
29.7MHz
33.0MHz
37.0MHz
Output Power
70W or more
60W or more
60W or less
Bandwidth
0.4MHz (+/-0.20MHz)
0.4MHz (+/-0.20MHz)
1.0MHz (+/-0.50MHz)
TK-6110K2
Frequency Bandwidth
35.0MHz
1.0MHz (+/-0.5MHz)
40.0MHz
1.8MHz (+/-0.9MHz)
50.0MHz
1.8MHz (+/-0.9MHz)
2. The TK-6110 design eliminates the need for the following accessories typical of Kenwood compact
mobiles:
a. KCT-19: 15-pin accessory connector is built in.
b. KAP-1: the Horn Alert output is provided on the 15-pin connector (see service manual for maximum
current rating).
Audio Power: 3W internal speaker / 10W external speaker (KES-5).
FleetSync® is not available for the TK-6110.
KES-3 is not compatible, use KES-5.
The following frequencies are not allowed in the TK-190 and TK-6110 models: 33.6 MHz and 42.0 MHz.
MODEL
TK-6110K
TK-6110K2
LIST
CABLES
KCT-18
788.00
788.00
LIST
Ignition sense cable
13.70
LIST
KLF-2
42.00
Page 1 of 2
TK-6110
March 2009
TK-690 / 790 / 890
VHF/UHF FM Mobile Radios
All 90 BKseries mobiles include:
• RF Deck Only
(Configuration Set & Assembly Labor Code
must be order for a Complete Mobile.)
TK-790K/890K mobiles include:
• KCH-10
• KCT-23M
• KMB-5
• KMC-27
(No need to use the assembly labor code)
Important Information
(TK-890; UHF)
* The lowest receive channel spread range
is the factory default tuning if not otherwise
specified. Refer to the table (right); order
L-850 (no charge) and specify receive
spread at the time of ordering. Out of range
orders cannot be accepted.
GENERAL FEATURES
• 45W & 110W (136-156, 148-174 MHz)
• 40W (403-430, 450-490, 480-512 MHz)
• 110W-75W (450-480 MHz)
• 110W (29.7-37.0, 35.0-43.0, 39.0-50.0 MHz)
• 160 Channels
• Single / Multi Group Scan
• QT / DQT
• Two-Tone Decode1
• DTMF Encode/ Decode / Stun
• Companded Audio
• Intercom
• Public Address
• Time Out Timer
• Ignition Sense
• Timed Power Off
• 7 Programmable AUX Inputs
• Panel Tuning
• Cloning
Model
RF Deck
Freq. Range
TK-890BK/K
450-490
20 MHz
40 MHz
Factory Def ault:
450-470
460-480
470-490
450-490
450-490
450-490
Order L-850:
TK-890BK2
TK-890BK3
* TX Power is derated
at 470-480 MHz for TK-890HBK:
- 450-469 MHz (100 W)
- 470-480 MHz (75 W)
RX
TX
Ch. Spread Ch. Spread
TK-890HBK
480-512
20 MHz
32 Mhz
Factory Def ault:
Order L-850:
480-500
492-512
480-512
480-512
403-430
20 MHz
27 MHz
Factory Def ault:
Order L-850:
410-430
403-423
403-430
403-430
450-480
20 MHz
30 MHz
Factory Def ault:
Order L-850:
450-470
460-480
450-480
450-480
MODEL
TK-690HBK
TK-690HBK2
TK-690HBK3
TK-790BK
TK-790BK2
TK-790HBK
TK-790K
TK-890BK
TK-890BK2
TK-890BK3
TK-890HBK
TK-890K
• MIL-Spec Noise-Cancel Mic (included)
FleetSync®
MOUNTING CONFIGURATIONS
• Dash Mount
• Single Head Remote Mount
• Dual Head Remote Mount
• Dual Band Remote Mount
• Dual Head / Dual Band Remote Mount
FRONT PANELS / CONTROL HEADS
• Transmit LED
• Busy, Call Alert, Warn LED
• LCD Dimmer Control
• Power On/Off Switch
• Rotary Volume Knob
• Rotary Selector Knob
• Backlit Keys
• PF Key Label Inserts
• Microphone Jack
• MILSTD 810 512.X Driven Rain
KCH-10 FRONT PANEL
• 5 PF Keys
• UP/DOWN Keys
• Built-in Front Speaker
KCH-11 FRONT PANEL
• 13 PF Keys
• UP/DOWN Keys
• External Speaker Required
LIST
29.7-37.0 MHz, 110W, 160 Channels (R.F. DECK ONLY)
148-174 MHz, 45W, 160 Channels
(R.F. DECK ONLY)
(R.F. DECK ONLY)
148-174 MHz, 110W, 160 Channels (R.F. DECK ONLY)
148-174 MHz, Basic Front("BMD"), 45W, 160 Channels
(R.F. DECK ONLY)
(R.F. DECK ONLY)
(R.F. DECK ONLY)
450-480 MHz, 100/75W, 160 Channels
(R.F. DECK ONLY)
450-490 MHz, Basic Front("BMD"), 40W, 160 Channels
Page 1 of 5
1,071.00
1,071.00
1,071.00
767.00
767.00
1,239.00
1,063.00
819.00
819.00
819.00
1,292.00
1,116.00
TK-690・790・890
March 2009
ACCESSORY CONFIGURATION SETS
LIST
CONFIGURATION SET DEFINITIONS
Note: All KCH-10 / Basic Control Head configurations are shipped with the control heads 4W internal
speaker enabled. Order L-891 to enable the 13W external speaker output for KES-5 speaker use. This
will disconnect the control heads internal 4W speaker !
Note: Order an Labor code for each model if factory packaging is required:
L-846 Package Dash/Single Head Remote*
L-847 Package Dual Head Remote
L-848 Package Dual Band Remote
L-849 Package Dual Band Dual Head Remote
(* TK-790K/890K are pre-packaged & fully assembled: basic front, medium power, dash mount mobiles.
No need to use the assembly labor code L-846.)
Single Band Dash Mount
KCH-10, KCT-23M2, KMB-9, KMC-27
9BHD1
9BMD1
9FHD1
9FMD1
LIST
KCH-10, KCT-23M, KMB-5, KMC-27
KCH-11, KCT-23M2, KMB-9, KMC-27, KES-5
KCH-11, KCT-23M, KMB-5, KMC-27, KES-5
Single Band Single Head Remote Mount
KCH-10, KRK-5, KCT-22M2, KCT-23M4, KMB-9, KMC-27
9BHSH1
9BMSH1
9FHSH1
9FMSH1
KCH-10, KRK-5, KCT-22M2, KCT-23M3, KMB-5, KMC-27
KCH-11, KRK-5, KCT-22M2, KCT-23M4, KMB-9, KMC-27, KES-5
KCH-11, KRK-5, KCT-22M2, KCT-23M3, KMB-5, KMC-27, KES-5
Single Band Dual Head Remote Mount
KCH-10(x2), KRK-6DH, KCT-22M2(x2), KCT-23M4, KMB-9, KMC-27(x2)
9BHDH1
9BMDH1
9FHDH1
9FMDH1
KCH-10(x2), KRK-6DH, KCT-22M2(x2), KCT-23M3, KMB-5, KMC-27(x2)
KCH-11(x2), KRK-6DH, KCT-22M2(x2), KCT-23M4, KMB-9, KMC-27(x2), KES-5(x2)
KCH-11(x2), KRK-6DH, KCT-22M2(x2), KCT-23M3, KMB-5, KMC-27(x2), KES-5(x2)
Dual Band Single Head Remote Mount
KCH-10, KRK-7DB, KMC-27, KCT-22M2, KCT-23M4(x2), KMB-9(x2)
9BHHDB
9BHMDB
9BMMDB
9FHHDB
9FHMDB
9FMMDB
KCH-10, KRK-7DB, KMC-27, KCT-22M2, KCT-23M3, KCT-23M4, KMB-5, KMB-9
KCH-10, KRK-7DB, KMC-27, KCT-22M2, KCT-23M3(x2), KMB-5(x2)
KCH-11, KRK-7DB, KMC-27, KES-5, KCT-22M2, KCT-23M4(x2), KMB-9(x2)
KCH-11, KRK-7DB, KMC-27, KES-5, KCT-22M2, KCT-23M3/KCT-23M4, KMB-5/KMB-9
KCH-11 KRK-7DB, KMC-27, KES-5, KCT-22M2, KCT-23M3(x2), KMB-5(x2)
Page 2 of 5
326.50
296.50
471.75
441.75
LIST
564.00
530.75
709.25
676.00
LIST
1,004.00
970.75
1,294.50
1,261.25
LIST
761.50
728.25
695.00
906.75
873.50
840.25
TK-690・790・890
March 2009
Dual Band Dual Head Remote Mount
KCH-10(x2), KMC-27(x2), KRK-8DBH, KCT-22M2(x2), KCT-23M4(x2), KMB-9(x2)
9BBHH
9BBHM
9BBMM
9FFHH
9FFHM
9FFMM
KCH-10(x2), KMC-27(x2), KRK-8DBH, KCT-22M2(x2), KCT-23M3, KCT-23M4, KMB-5,
KMB-9
KCH-10(x2), KMC-27(x2), KRK-8DBH, KCT-22M2(x2), KCT-23M3(x2), KMB-5(x2)
KCH-11(x2), KMC-27(x2), KRK-8DBH, KCT-22M2(x2), KCT-23M4(x2), KMB-9(x2), KES5(x2)
KCH-11(x2), KMC-27(x2), KRK-8DBH, KCT-22M2(x2), KCT-23M3, KCT-23M4, KMB-5,
KMB-9, KES-5(x2)
KCH-11(x2), KMC-27(x2), KRK-8DBH, KCT-22M2(x2), KCT-23M3(x2), KMB-5(x2), KES5(x2)
FRONT PANELS & REMOTE KITS
KCH-10
KCH-11
KRK-5
KRK-6DH
KRK-7DB
KRK-8DBH
(Order Configuration Sets for full install accessories)
Basic Control Panel
Full Featured Control Panel
Single Control Head Remote Mount Kit
Dual Control Head Remote Mount Kit
Dual Band Control Head Remote Mount Kit
Dual Band Dual Head Remote Mount Kit
CABLES
KCT-18
KCT-22M
KCT-22M2
KCT-22M3
KCT-23M
KCT-23M2
KCT-23M3
KCT-23M4
1,051.00
1,408.00
1,374.75
1,341.50
LIST
147.00
231.00
147.00
252.00
262.50
283.50
LIST
Control cable - 8 Feet
Control cable - 17 Feet (Standard accessory config. set cable)
Control cable (25 Feet)
DC Cable (35/45W Dash mount)
DC Cable (75/110W Dash mount)
DC Cable (35/45W Remote mount)
DC Cable (75/110W Remote mount)
KCK-6
LIST
1,117.50
1,084.25
13.70
73.50
84.00
94.50
31.50
38.75
34.75
45.25
LIST
Auxiliary Adapter for 90-Series Mobiles (For AUX A, B, & C)
138.25
Features: 90-Series AUX A, B, & C Inputs, 3 AUX 1 Amp Relay Outputs, D-Sub 25 90-Series Accessory
Connector Parallel Feed Through
Supplied Items: Instruction Sheet (1pc.), KCK-6 (1pc.), Insulated Spade Lugs [0.250 female fully
insulated, 16-14 wire range] (8pcs.)
***Hardware that may be required but NOT supplied - two 3/16" mounting screws, male-to-female DB-25
straight through serial cable, & wire peripheral.**
Caution: KCK-6 Relays are rated at 1A maximum. Do Not Exceed. The KCK-6 is not intended to directly
drive siren and light packages. The siren/light package manufacturers recommended high amperage relay
units and directions should be followed.
KLF-2
KMB-10
KMB-5
KMB-9
Key Lock Adapter for use with KMB-4/5/6
Medium Power Mounting Bracket (35W/45W models)
High Power Mounting Bracket with built-in key lock (75W/110W models)
42.00
26.30
14.00
36.75
LIST
KES-5
KMC-27
External Speaker (40W max input)
KMC-28
KMC-9B
DTMF microphone (MIL-SPEC, Noise canceling)
Rugged standard microphone with noise canceling, MIL-STD and driven rain features
Desk top microphone
Page 3 of 5
61.25
104.00
163.00
96.50
TK-690・790・890
March 2009
KPG-43AM
KCT-53UM
LIST
KPG-44DK
*****************
K29-5276-03
K29-5277-03
Key Inserts for 90-series mobile (AN, D/A, DIM, HA, HC, IC, MON, OPT, OST, PA)
K29-5305-03
S76-0434-05
Key Inserts for 90-series mobile (RCL, RPT, SCN, SP, SPM, SQ, TA, <up arrow>, <down
arrow>)
Key Inserts for 90-series mobile (CH1, CH2, CH3, CH4, CH5, AUXA, AUXB, AUXC, EMG,
ORG)
1 Amp Relay for 90-series mobile
OPTION MODULES
CIM-1000
114.50
86.00
68.50
14.00
14.00
14.00
11.22
LIST
131.25
board).
CIM-CABLE
61.25
LIST
L-846
L-847
L-848
L-849
L-850
L-854
L-858
Package Dash/Single Head Remote for 90-series mobiles
Modify 90-series mobile Single Band (Single Head) Mobile for Pyramid Vehicular Repeater
17.00
34.00
34.00
50.00
N/C
30.00
75.00
L-859
Modify 90-series mobile Single Band (Dual Head) Mobile for Pyramid Vehicular Repeater
75.00
L-861
Install Horn Alert output relay for 90-series mobiles (1 amp max.)
70.00
Package Dual Head Remote for 90-series mobiles
Package Dual Band Remote for 90-series mobiles
Package Dual Band Dual Head Remote for 90-series mobiles
Tune TK-890 receiver channel spread (20 MHz max.); specify receive spread
90 Mobile Programming (with basic TX/RX check)
--- Part #S76-0407-05 Relay incl.
L-862
Install Key Inserts for 90-series mobiles
15.00
Note: For new radio tune orders only. Installs only the included KCH-10/11 key inserts. Must specify keys
and placement (see Service Manuals for placement diagram, pg. 14). Also, see Service Manuals for
technical details (pg. 14). Other Key Inserts are available from Parts Dept. See the "Service Related
Accessories" section of the 90-series mobiles pricepages for more information.
L-864
KCT-22A Extended Control Head Cable (up to 50 ft. max.)
190.00
Note: Please specify exact length at 1ft. increments when ordering.
Caution: Extended control head cables exhibit a loss in speaker audio power to the control heads. For
either type control head (KCH-10/11), it is recommended that the 13W audio output modification be
implemented to drive extended cable runs and a KES-5 external speaker be used. Refer to the service
manual pg. 15-17 for 13W modifications. Installing new radio firmware (hex files) via the KPG-44D
software nor checking the firmware "checksum" is not possible through an extended control head cable. A
standard KCT-22 cable of 25 ft. or less should be used when this has to be done. Normal KPG-44D radio
parameter programming is possible at extended lengths.
Page 4 of 5
TK-690・790・890
March 2009
L-865
LIST
KCT-22A Extended Control Head Cable (up to 100 ft. max.)
245.00
Note: Please specify exact length at 1ft. increments when ordering.
Caution: Extended control head cables exhibit a loss in speaker audio power to the control heads. For
either type control head (KCH-10/11), it is recommended that the 13W audio output modification be
implemented to drive extended cable runs and a KES-5 external speaker be used. Refer to the service
manual pg. 15-17 for 13W modifications. Installing new radio firmware (hex files) via the KPG-44D
software nor checking the firmware "checksum" is not possible through an extended control head cable. A
standard KCT-22 cable of 25 ft. or less should be used when this has to be done. Normal KPG-44D radio
parameter programming is possible at extended lengths.
L-866
KCT-23A-K2 Two Conductor 75/110W High Power DC Cable
75.00
(2 Conductor: 1x23 ft. positive, 1x23 ft. negative; AWG #10)
Note: This cable substitutes for the ff: DC Cables:
--> KCT-23M2 75/110W Dash Mount DC Cable: 4 Conductor: 2x10 ft. positive, 2x10 ft. negative
--> KCT-23M4 75/110W Remote Mount DC Cable: 4 Conductor: 2x23 ft. positive, 2x23 ft. negative
L-867
Jumper foil for SB to pin 14 of accessory connector for 90-series mobile
25.00
(Ref. 90-Series Mobile Service Manual, page 17/18)
L-870
50.00
L-883
L-891
L-903
L-910
Modify 90-series mobile for KCT-18
25.00
10.00
17.00
17.00
External speaker modification for 90-series mobile Control Head (13W)
R640 mic input modification for 90-series mobile
Install firmware 094F (90-series mobile * and # DTMF without PTT)
Note: The firmware 094F gives the 90-series mobile the ability to generate a DTMF tone from the * and #
keys without pushing the PTT button.
L-912
L-917
90-Series mobile low imp. mic. Input at RF deck
EXT PTT / Local KMC-27 mic disable
10.00
17.00
Purpose: Disables the KMC-27 mobile hand mic element when 90-series mobile external PTT is active.
For use with data modems, GPS AVL data units, headset systems (motorcycles, ambulance, fire engines),
vehicle intercom
L-921
L-922
L-1036
L-1037
Modify 90-series mobile Dual Band (Single Head) for Pyramid Vehicular Repeater
Modify 90-series mobile Dual Band (Dual Head) for Pyramid Vehicular Repeater
Page 5 of 5
75.00
75.00
75.00
75.00
TK-690・790・890
March 2009
LIST
KMC-27A
KMC-27B
KMC-28A
KMC-9C
KES-5
Ext. speaker, 40W max input; blk,. case, 5"x5"x2-9/16"
104.00
42.00
163.00
86.00
61.25
Note: plugs into TK-6110 6-pin molex acc. conn.
MISCELLANEOUS ITEMS
KPS-15
LIST
KPG-46AM
KCT-53UM
LIST
Radio Programming Interface Cable
KPG-59DK
USB Adapter for KPG-xxAM DB9F Programming Interface Cables (DB9M - to - USB Type
A connector);
Program Software for TK-190/6110 (Version 2.00)
*****************
E30-3382-05
J29-0662-03
N99-0395-05
Clone cable
Mounting bracket (Same as supplied)
Screw set for mounting bracket Part #J29-0662-03
OPTION MODULES
CIM-1000
173.00
191.00
86.00
68.50
11.28
39.50
2.99
LIST
131.25
board).
CIM-CABLE
61.25
L-1040
L-1041
L-911
LIST
TK-6110 CIM-1000/MDC1200 ENCODER INSTALLATION
TK-6110 CIM-1000/GE STAR ENCODER INSTALLATION
TK-190/TK-6110 Programming (with basic TX/RX check)
Page 2 of 2
75.00
75.00
25.00
TK-6110
March 2009
TK-5710 / 5810
VHF/UHF FM & P25 Digital Mobile Radios
All P25 series mobiles include:
• RF Deck Only
(Configuration Set & Assembly Labor Code
must be order for a Complete Mobile.)
* TX Power is derated
at 500-520 MHz for TK-5810HBK:
450-499 MHz (100 W)
500-520 MHz (60 W)
GENERAL FEATURES
• 50W & 110W (136-174 MHz)
• 45W & 100 W (450-520, 400-470 MHz)
• 50 Zones / 512 Channels
• Zone/CH Voice Announce
• Emergency Features
• Tactical Group
• Intercom
• Public Address
• Time Out Timer
• Ignition Sense
• Timed Power Off
• DB-25 & 9-Pin Accessory Connectors
• Transceiver Password
• Field-Programming & Tuning
• Cloning
• Easy Option Ports (26-pin)
• DB-25 & 9-Pin Accessory Connectors
• MIL-STD 810 C/D/E/F, IP-54
• MIL-STD Noise-Cancel Mic (included)
• MIL-STD 12-Key DTMF Mic Option
MOUNTING CONFIGURATIONS
• Dash Mount
• Single Control Head Remote Mount
• Dual Control Head Remote Mount
FRONT PANELS/CONTROL HEADS
KCH-14 Front Panel
• 5 PF Keys
• Built-in Front Speaker
KCH-15 Front Panel
• 11 PF Keys
KCH-16M Handheld Control Head
• 9 PF Keys
• 12-Key DTMF/Function Keypad
• Single Zone/Multi-Zone Scan
• Scan Lists
• Conventional Scan
FM
• QT / DQT
• Two-Tone Decode / Encode
• DTMF Encode / Decode / Stun
• Horn Alert Output
• Companded Audio
FleetSync® (FM)
• Emergency & Stun Statuses
• Selective & Group Call
• Text Messaging
P25 DIGITAL
• P25 Digital Trunking Option
• IMBETM VOCODER
• RSSI Indicator
• Remote Monitor
• Remote Check
• Radio Inhibit
• Encryption Key Zeroize (SCM required)
• Encryption Key Retention (SCM required)
• DES 16-Key SCM Option
• AES FIPS 140-2 & DES 16-Key SCM Option
MODEL
LIST
VHF Version 2 radios only (SN 80600001 or later)
TK-5710BK
TK-5710HBK
TK-5810BK
TK-5810BK2
TK-5810HBK
TK-5810HBK2
136-174MHz 10-50W 50 Zones/512 Channels (R.F. DECK ONLY)
136-174MHz 50-110W 50 Zones/512 Channels (R.F. DECK ONLY)
450-520 MHz 5-45W 50 Zones/512 Channels (R.F. DECK ONLY)
Page 1 of 6
1,840.00
2,352.00
1,840.00
1,840.00
2,352.00
2,352.00
TK-5710・5810
March 2009
ACCESSORY CONFIGURATION SETS
LIST
CONFIGURATION SET DEFINITIONS
Dash Mount
10BHD
10BMD
10FHD
10FMD
LIST
KCH-14M, KCT-23M2, KMB-9, KMC-27
KCH-14M, KCT-23M, KMB-5, KMC-27
KCH-15M, KCT-23M2, KMB-9, KMC-27, KES-5
KCH-15M, KCT-23M, KMB-5, KMC-27, KES-5
Single Head Remote Mount
KCH-14M, KRK-5, KCT-22M2, KCT-23M4, KMB-9, KMC-27
10BHSH
10BMSH
10FHSH
10FMSH
KCH-14M, KRK-5, KCT-22M2, KCT-23M3, KMB-5, KMC-27
KCH-15M, KRK-5, KCT-22M2, KCT-23M4, KMB-9, KMC-27, KES-5
KCH-15M, KRK-5, KCT-22M2, KCT-23M3, KMB-5, KMC-27, KES-5
Dual Head Remote Mount
KCH-14M(x2), KRK-6DH, KCT-22M2(x2), KCT-23M4, KMB-9, KMC-27(x2)
10BHDH
10BMDH
10FHDH
10FMDH
KCH-14M(x2), KRK-6DH, KCT-22M2(x2), KCT-23M3, KMB-5, KMC-27(x2)
KCH-15M(x2), KRK-6DH, KCT-22M2(x2), KCT-23M4, KMB-9, KMC-27(x2), KES-5(x2)
KCH-15M(x2), KRK-6DH, KCT-22M2(x2), KCT-23M3, KMB-5, KMC-27(x2), KES-5(x2)
Handheld Control Head Remote
KCH-16M, KRK-11M, KCT-22M2, KCT-23M4, KMB-9, KES-5
10CHSH
10CMSH
KCH-16M, KRK-11M, KCT-22M2, KCT-23M3, KMB-9, KES-5
FRONT PANELS & REMOTE KITS
KCH-14M
Basic Remote Control Head w/ 12 Alphanumeric Display (4W Front Speaker)
683.50
653.50
744.75
714.75
LIST
921.00
887.75
982.25
949.00
LIST
1,718.00
1,684.75
1,840.50
1,807.25
LIST
1,056.75
1,046.25
LIST
504.00
Note: All KCH-14 / Basic Control Head configurations are shipped with the control heads 4W internal
speaker enabled. Order L-1008 to enable the 13W external speaker output for KES-5 speaker use. This
will disconnect the control heads internal 4W speaker !
KCH-15M
Full-Featured Remote Control Head w/ 14 Alphanumeric Display
504.00
Note: requires an external speaker
KRK-5
KRK-6DH
Single Control Head Remote Mount Kit
HANDHELD CONTROL HEAD REMOTE
KCH-16M
147.00
252.00
Dual Control Head Remote Mount Kit
Handheld Control Head for P25 Mobiles
LIST
546.00
Note: requires KRK-11M, KCT-22M/M2/M3, & KES-5
KRK-11M
KCH-16M HHCH Interface Kit for Single Head Remote
Page 2 of 6
283.50
TK-5710・5810
March 2009
CABLES
KCT-18
KCT-22M
KCT-22M2
KCT-22M3
KCT-23M
KCT-23M2
KCT-23M3
KCT-23M4
LIST
Control cable - 17 Feet (Standard accessory config. set cable)
KLF-2
KMB-10
KMB-5
KMB-9
LIST
Key Lock Adapter for use with KMB-4/5/6
Medium Power Mounting Bracket (10-50W models)
High Power Mounting Bracket with built-in key lock (50-110W models)
KES-5
KMC-27
KMC-28
KMC-9B
13.70
73.50
84.00
94.50
31.50
38.75
34.75
45.25
42.00
26.30
14.00
36.75
LIST
External Speaker (40W max input)
MIL-SPEC noise-canceling mobile hand microphone
MIL-SPEC DTMF noise-canceling mobile hand microphone
Desk top microphone
61.25
104.00
163.00
96.50
LIST
KPG-43AM
KCT-53UM
KPG-95DK
114.50
86.00
628.00
Includes "Dealer Level License ID" for FM & P25 Conventional modes only.
See L-989 KPG-95DK Network Level ID (Trunking System Privileges) - Restricted Purchase
Requirements.
Note: A Dealer Level License ID can load network data files provided by a Network Level Licensed KPG95DK, but cannot change trunked network parameters.
KPG-95D V4.00 or later (no key loader): TK-5210/5710/5310/5810 VER1 & VER2 Radios (all Serial
No.s)
Note: A Kenwood Key Loader for VER2 radios is NOT currently available (see KWD-DE20/KWD-AE20)
KPG-95D V3.11 or earlier (no key loader): TK-5210/5710 VER1 Radios (before SN 8060000) ONLY
KPG-95DTKL VX.XX (includes key loader; discontinued): TK-5210/5710 VER1 Radios (before SN
8060000) ONLY
KPG-94
Key Loader Interface Cable for Motorola KVL-3000/3000 Plus
*****************
K29-5276-03
Key Inserts for 90-Series/TK-5710/5810 (AN, D/A, DIM, HA, HC, IC, MON, OPT, OST, PA)
14.00
K29-5277-03
Key Inserts for 90-Series/TK-5710/5810 (RCL, RPT, SCN, SP, SPM, SQ, TA, <up arrow>,
<down arrow>, 1x Clear key insert)
Key Inserts for 90-Series/TK-5710/5810 (CH1, CH2, CH3, CH4, CH5, AUXA, AUXB, AUXC,
EMG, ORG)
Key Inserts for TK-5710/5810 (2TN, AD, AR, CLK, FNC, PBK, SCP, SEC, SEL, SES)
14.00
K29-5305-03
K29-9353-13
K29-9354-03
K29-9356-03
Key Inserts for TK-5710/5810 (GPS, STS, TAC, TON, RES, IDV, KDL, TGR, 2x Clear key
inserts)
Key Inserts for TK-5710/5810 (PAG, SIT, SRC, 7 X Clear key inserts)
Page 3 of 6
262.50
14.00
14.00
14.00
14.00
TK-5710・5810
March 2009
FRIMWARE OPTIONS
KWD-TR20
LIST
Trunking Option for TK-5210/5710/5310/5810
875.00
Must order L-1056
Note: KPG-95DK Requires Network Level License ID to program trunked network radio parameters (see
KPG-95D for purchase restrictions & requirements)
Compatible with TK-5210 Version 2 (SN 80600001 or later); TK-5310 (SN 809xxxxx or later); TK-5710
Version 2 (SN806xxxxx); TK-5810 (SN 809xxxxx or later)
KWD-RK20
OTAR Option for KWD-AE20K Encryption Module for P25 Conventional Only;
models TK-5x10 (VER2; except K7)
830.00
Must order:
• With KWD-AE20K (SN 005xxxxx or later)
• L-1109 for mobile Installation (no charge)
Notes:
• Provides OTAR on P25 Conventional only (TIA/EIA-102.AACA compliant; not for use over trunked
systems)
• Compatible with Motorola KMF P25 conventional OTAR
• Not compatible with Motorola-proprietary (non-TIA/P25) KMF features
• Not compatible with K7 64 Ch Model
• Requires KPG-95D V5.40 or later for radio programming
• Option deletes self-programming, cloning and analog FleetSync® (except PTT ID/Emergency) when
installed.
KWD-RK20 is an U.S. DOC/BIS Export Controlled Item (ECCN 5D002A)
SOFTWARE OPTIONS
KPG-114DE
LIST
DES Encryption Software Key Loader for KWD-DE21K/KWD-AE21K
368.00
KPG-114DE is a U.S. DOC/BIS Export Controlled Item (ECCN 5D992A.1)
KPG-113AE
AES/DES Encryption Software Key Loader for KWD-DE21K/KWD-AE21K
525.00
KPG-113AE is a U.S. DOC/BIS Export Controlled Item (ECCN 5D002A)
OPTION MODULES
KWD-DE20K
LIST
578.00
KWD-DE20K requires: a Motorola KVL3000 or KVL3000 Plus key loader device.
KWD-DE21K
578.00
Order L-1602 if installation is required
Note: Requires KPG-114DE or KPG-113AE software key loader or Motorola KVL3000 Plus key loader
device
KWD-AE20K
AES FIPS140-2 & DES Encryption Module for TK-5210/5710/5310/5810
998.00
KWD-AE20K requires: a Motorola KVL3000 Plus key loader device.
KWD-AE21K
AES & DES Encryption Module for TK-5210/5710/5310/5810
998.00
Note: Requires KPG-113AE software key loader or Motorola KVL3000 Plus key loader device.
CIM-1000K-26
131.25
MDC-1200 or G-Star.
the board).
Page 4 of 6
TK-5710・5810
March 2009
OPTION MODULES - CONT'D
CIM-CABLE
LIST
61.25
VGS-1
87.50
Note: VGS-1 provides Auto-Record, Voice Memo & Playback; The Voice Guide (a.k.a annunciation)
function is built-in to the TK-5710/5810 and does not require the VGS-1
L-862
LIST
Install Front Panel PF Key Label Inserts in TK-5710/5810/90-series Mobile
15.00
(key names and positions must be specified)
L-864
KCT-22A Extended Control Head Cable
190.00
(Specify length in 1 ft increments up to 50 ft. max.)
L-865
KCT-22A Extended Control Head Cable
245.00
(Specify length in 1 ft. increments up to 100 ft. max.)
Extended control head cables:
Extended cables result in a loss of control head audio power. On KCH-14 use 13W audio output
modifications per service manual Use a standard KCT-22 25 ft. or less cable for firmware installation.
Normal KPG-95D radio programming is possible at extended lengths.
L-866
Modify KCT-23M2/M4 110W High Power DC Cables from 4 to 2 Conductors
75.00
(1x23 ft. positive, 1x23 ft. negative; AWG #10)
Two Conductor Modification:
KCT-23M2 75/110W Dash Mount DC Cable ( 4 Conductor: 2x10 ft. positive, 2x10 ft. negative)
KCT-23M4 75/110W Remote Mount DC Cable (4 Conductor: 2x23 ft. positive, 2x23 ft. negative)
L-962
L-989
KPG-95DK Network Level ID (encrypted data file)
25.00
132.00
Note: Enables Trunking system programming privileges; See KPG-95DK Network Level ID (Trunking
System Privileges)
- Restricted Purchase Requirements The KPG-95D only ships with a "Dealer Level License ID" which permits Conventional FM and P25
Conventional radio programming privileges only. For radios with the P25 Trunking option installed,
trunked/network programming privileges require a "Network Level License ID" generally reserved ONLY
for the system owner or the system owners authorized operators/service centers. Purchasing the KPG95DK Network Level License ID will require 1) Written verifiable authorization from the systems
owner/operator. 2) The 3-digit hexadecimal P25 System ID from the system owner/operator. 3) Purchase
of a L-989 : KPG-95D Network Level ID option. This option will include an encrypted KPG-95D "System
Key Data File" containing the 16-digit Network Level License ID & 3-digit hexadecimal System ID code.
L-1005
TK-5710/5810 Programming
125.00
(Basic TX/RX check only with factory test freq.s or dealer/customer provided KPG-95D data file)
L-1006
Modify TK-5710/5810 for Horn Alert relay output
25.00
(1 amp max.; relay factory installed already)
L-1008
External Speaker modification for TK-5710/5810 mobile Control Head (13W)
10.00
Note: All Basic Control Head (KCH-14M) configurations are shipped with the control heads 4W internal
speaker enables. Order L-1008 to enable the 13W external speaker output for KES-5 speaker use. This
will disconnect the control heads internal 4W speaker!
L-1024
L-1025
L-1028
L-1029
L-1110
L-1056
L-1109
Package Dash/Single Head Remote for 5710/5810 mobiles
Package Dual Head Remote for 5710/5810 mobiles
Package HHCH Remote for 5710/5810 mobiles
Install KWD-TR20 Trunking Option in TK-5710/5810
(Must purchase KWD-TR20K separately)
Install KWD-RK20 OTAR Option in TK-5710/5810
75.00
75.00
17.00
34.00
25.00
N/C
N/C
(Must purchase KWD-RK20 separately)
L-1345
Install KWD-AE20K in TK-5710/5810 Mobile
75.00
L-1346
Install KWD-AE21K in TK-5710/5810 Mobile
75.00
Page 5 of 6
TK-5710・5810
March 2009
L-1601
LIST
Install KWD-DE20K in TK-5710/5810 Mobile
75.00
L-1602
Install KWD-DE21K in TK-5710/5810 Mobile
75.00
-- IMPORTANT NOTES -Encryption modules, key loaders and radios containing encryption are export controlled by the U.S. Department of Commerce Bureau of Industry & Security
EAR regulations and may either require an Export License, are eligible for a License Exception (ENC) or are exportable with No License Required (NLR) depending on
the country, the consignee and the intended use. High level encryption is a special commodity that may require an export license to most countries. See www.bis.gov
for more information regarding export regulations. DO NOT SHIP encryption items outside the U.S. without proper DOC/BIS Export Licenses and/or compliances.
* Address:
* Contact Phone:
* Address:
* Contact Phone:
-------------------------------------------------------------------------------------------------KWD-AE20 AES FIPS140-2 SCM , NIST Validation & Customer Shipping
A secure delivery method direct to the end user customer is required by the NIST AES FIPS 140-2 validation rules. For U.S. Federal Government entities the SCM
must ship from Kenwood USA Corporation directly to the end user customer by a trusted carrier (FEDEX, UPS or a designated Kenwood USA Corporation employee);
shipping/handling by a dealer or other entity is not acceptable. This may or may not be required by local/state government agencies or business/industrial users.
Please check with the end use customer about their AES encryption handling requirements before ordering. Kenwood will not be responsible for shipments of KWDAE20K modules to erroneous destinations specified on an order.
Page 6 of 6
TK-5710・5810
March 2009
TK-980 / 981
800/900 MHz Trunked Mobile Radios
All 80/81 series mobiles include:
GENERAL FEATURES
• Windows ® Programming & Tuning
• 15 W 800 & 900 MHz Models
• Windows ® Firmware Uploading
• Trunked Format
• LTR® Trunked Systems
• Cloning
• Conventional Systems
• 32 Systems / 250 Groups
• NPSPAC Option
• System Scan
• List Type System Scan
CONVENTIONAL ZONES
• QT / DQT
• Single Priority Group Scan
TRUNKED ZONES
• Companded Audio
FleetSync®
• Time Out Timer
• Timed Power Off
• ACC Cable Option
• Ignition Sense
• Dynamic Mobile Mic Included
• MIL-Spec Noise-canceling Mic Option
• MIL-Spec 12-Key Noise-canceling Mic Option
MODEL
TK-980
L-889
LIST
800 MHz, 15W LTR-32 Systems, CONV-250 CH.
551.00
84.00
Note: Other required items: KPG-49D (V2.00 or higher) higher permits "per channel"
programming of NPSPAC capability.
NPSPAC and PassPort® capabilty are not available in the same firmware option.
TK-981
900 MHz, 15W LTR-32 Systems, CONV-250 CH.
569.00
Important Note:
The TK-480/481/980/981 only operate in "Trunked Format" (LTR & Conventional systems). These are not
"Dual Format" radios like the TK-280/380/780/880 mobiles which operate in either Trunked Format (LTR &
Conventional systems) or Conventional Format (traditional conventional channel organization with priority
scan).
®
LTR
is a registered trademark of E.F. Johnson Co.
LIST
KAP-1
KCT-18
KCT-19
Horn Alert/P.A. Relay Option (Requires KCT-19)
KCT-34
KCT-36
KLF-2
KMB-6
KMB-10
Ignition sense cable (Requires KCT-19)
Accessory connector cable (for ignition sense, horn alert, KSP- spkrs, & Data Port)
KCT-34/35/39/40M Extension Cable; 117.6 inches (9.8 ft)
Mobile mounting bracket (same as supplied)
Key lock adapter (for both KMB-4 & 6)
Page 1 of 5
42.00
13.70
22.00
22.00
43.75
42.00
12.35
26.30
TK-980・981
March 2009
KCT-31
KMC-9C
KMB-20
KPS-15
PC Serial Interface cable (80-Series mobile-to-PC connection for FleetSync®)
73.50
86.00
26.30
173.00
LIST
KMC-27A
KMC-27B
KMC-28A
KMC-9C
KES-3
KES-5
External speaker, 40W max input, blk case; 5"x5"x2-9/16" (requires KCT-19)
• DC Cable
LIST
104.00
42.00
163.00
86.00
44.25
61.25
LIST
KDS-100 FEATURES
Important Note:
KDS-100
625.00
KPG-71DK
KCT-34
KCT-36
Page 2 of 5
103.25
22.00
43.75
TK-980・981
March 2009
KAS-2FSD
LIST
384.00
Note:
• TK-980/981base mobile requires a KCT-31 PC serial cable to connect to the base computer (purchase
seperately).
& mobiles.
AVL UNITS
LIST
KGP-2A/2B FEATURES
4205 Park Dr.
Ph.: 512-267-7800, Fax: 512-267-9200
2. KCT-34 interface cable & L-929 install code - connects the KGP-2B to the base/control station mobile
3. Computer Serial Cable Required (not supplied)- The KGP-2B-to-PC COM port connection for AVL data is made via a dealer-supplied computer serial communication
port cable. The serial cable should be a D-Sub 9-Pin Female (KGP-2B; ACC1 end) and the appropriate D-Sub 9-Pin or 25-Pin on the PC serial COM port end. Serial
2. KCT-34 interface cable & L-929 - connects the KGP-2A to the fleet 80-Series mobile
3. Note: KCT-19 & KCT-34 cables cannot be installed simultaneously- Therefore using a KCT-34 excludes plug-in of a KCT-19 for KES-5 external speaker (use KES-3),
Horn Alert output, Data modem I/O's, footswitch input and headsets.
KGP-2A
551.00
2. L-929 - Install KCT-34 to 80-Series Mobile for KGP-2A/2B interface
KGP-2B
Base Modem Unit
236.50
2. L-929 - Install KCT-34 to 80-Series Mobile for KGP-2A/2B interface
KCT-34
KCT-36
KPG-73DK
Page 3 of 5
22.00
43.75
103.25
TK-980・981
March 2009
KPG-46AM
KCT-53UM
LIST
KPG-49DK
Windows® Programming Software for TK-480/481/980/981 V3.00 or higher
*****************
E30-3382-05
J29-0627-13
Clone cable
Mounting bracket for TK-780/880/980/981 --- same as supplied w/ radio
L-857
L-889
191.00
86.00
68.50
11.28
7.04
LIST
80 Mobile Programming (with basic TX/RX check)
25.00
84.00
Note: NPSPAC and PassPort capabilty are not available in the same firmware option.
L-918
L-929
Install KCT-31 in 80-Series mobile (order KCT-31 separately)
Install KCT-34 to 80-Series mobile for KDS-100/KGP-2A/2B interface
(order KCT-34 separately)
Page 4 of 5
21.00
21.00
TK-980・981
March 2009
LIST
PassPort® Options for NEW Radio Orders (Kenwood-installed)
For 800/900 MHz models TK-480/481/980/981 new radio orders, the Kenwood-installed Passport® ESN / firmware option is available for a charge: Order the
ESN/Firmware option per L-876, L-877 or L-878.
KPG-63D Radio Programming Software: the KPG-63D is required to program all PassPort® parameters for all PassPort® enabled radios, the KPG-63D will not program
LTR or conventional parameters. KPG-49D is required only if LTR or conventional systems are to also be programmed in the PassPort® radio.
KPG-63DK
L-876
L-877
68.00
L-878
· 100 qty. lot price; Price is per ESN
68.00
Install PassPort® ESN options and firmware in TK-480/481/980/981
68.50
68.00
PassPort® Options for Dealer/Operator Field Conversions (Field-installation kits)
1. Order the ESN key/firmware Labor Code options: L-892 or L-894; specify model radio(s).
Pre-loaded ESN hardware key(s) with the ordered quantities of ESN's & a PassPort® radio firmware diskette will be shipped (100 ESN's maximum per hardware key).
Important: Any depleted key previously registered to a technicians computer must be retained to register any new purchased key to the computer; please retain the old
key until the new one is received.
a. KPG-64D: PassPort® ESN Install Program: the KPG-64D only needs to be ordered one time. It is re-useable for subsequent ESN orders (unless an upgrade is
recommended).
b. KPG-63D Radio Programming Software: required to program all PassPort® parameters for all PassPort® enabled radios, the KPG-63D will not program LTR or
conventional parameters.
c. KPG-49D Radio Programming Software: required only if LTR or conventional systems are also to be programming in the PassPort® radio.
3. The KPG-49D radio programming software is required for LTR & conventional site programming.
L-892
L-893
L-894
SRB08698
Hardware Key (Maximum 100 ESNs per hardware key)
68.00
68.00
68.00
87.50
®
- requires KPG-64D to download PassPort ESN options into an 80-Series radio.
computer.
KPG-64DK
PassPort® ESN Field Installation Software V1.12
10.50
· V1.12: supercedes V1.11; upgrade to V1.12 recommended for improved ESN file database features
KPG-63DK
Page 5 of 5
68.50
TK-980・981
March 2009
NX-700 / 800
TM
NEXEDGE VHF/UHF Digital & FM Mobile Radios
All NX series mobiles include:
• Blade Fuse
NX-800K:
450-489 MHz (30 W)
490-512 MHz (25 W)
NX-800HK: 450-489 MHz (45 W)
490-512 MHz (40 W)
GENERAL FEATURES
• 30W / 50W (136-174 MHz)
• 30W / 45W (400-470, 450-520 MHz)*
• 512 CH-GID / 128 Zones
• Dash & Remote Mount
• RSSI Indicator
• On/Off Power Control
• 4 Up/Down Selectors
• 6 Front PF Keys
• Emergency/AUX Key
• 4W Speaker Audio
• Time Out Timer
• Ignition Sense
• KPG-111D Windows® FPU
• Flash Firmware Upgrading
• Front Panel Test & Tune
• Cloning
• GPS Receiver Option
• VGS-1 Voice Guide/Storage Option
DIGITAL CONVENTIONAL MODE
• 64 Radio Access Numbers (RAN)
• Individual & Group Selective Call
• Mixed FM/Digital Operation
DIGITAL – COMMON
• NXDN® Digital Air Interface
• AMBE+2™ VOCODER
• 6.25 & 12.5 kHz Channels
• Over-the- Air Alias
• Paging Call
• Emergency Call
• All Group Call
• Remote Stun/Kill
• Remote Check
• Short & Long Data Messages
• GPS Location with Voice
• NXDN® Scrambler Included
FleetSync®/II (FM)
• Input/Output Status Messages
• Send/Display GPS
MODEL
NX-700K
NX-700HK
NX-800K
NX-800K2
NX-800HK
NX-800HK2
DIGITAL TRUNKING MODE
• Individual Private Call
• Group Call
• Broadcast Call
• Transmission Trunked Mode
• Message Trunked Mode
• Call Queuing with Priority
• Call Queue Pre-emption
• Late Entry (UID & GID)
• 4 Priority Monitor ID’s
• Remote Group Add
• Multi-Site IP Network Compatible
SCAN
• Single Zone / Multi-Zone / List Scan
• Dual Priority Scan (Conventional)
FM MODES - GENERAL
• 25 & 12.5 kHz Channels
• FleetSync®/II
• DTMF Encode/Decode
• Companded Audio
• Voice Inversion Scrambler
• Encryption/ANI Board Control
FM CONVENTIONAL ZONES
• QT / DQT
• Two-Tone Decode
• Single/Two-Tone Encode
• Call Key 1-6
FM LTR® TRUNKED ZONES
LIST
136-174 MHz 30W, 512 CH / 128 Zone
136-174 MHz 50W, 512 CH / 128 Zone
450-520 MHz 30W, 512 CH / 128 Zone
400-470 MHz 30W, 512 CH / 128 Zone
450-520 MHz 45W, 512 CH / 128 Zone
400-470 MHz 45W, 512 CH / 128 Zone
Page 1 of 3
725.00
850.00
725.00
725.00
850.00
850.00
NX-700・800
March 2009
LIST
63.00
13.70
42.00
26.30
105.00
31.50
34.75
KAP-2
KCT-46
KLF-2
KMB-10
KRK-10
KCT-23M
KCT-23M3
Key lock adapter
DC Cable (35-50W Dash mount; pos/neg. 10 ft. leads)
DC Cable (35-50W Remote mount; pos.23 ft.; neg. 3.3. ft. leads)
KMC-9C
KMB-24
KPS-15
KMC-35
KMC-36
KMC-9C
KES-3
KES-5
LIST
86.00
42.00
173.00
LIST
Standard dynamic mobile microphone with 12 keypad (8-pin mod. plug)
52.50
94.50
86.00
44.25
61.25
OPTION MODULES
VGS-1
CIM-1000K-26
LIST
87.50
131.25
the board).
CIM-CABLE
61.25
Page 2 of 3
NX-700・800
March 2009
FleetSync ® & NEXEDGE TM AVL & MESSAGING
KGS-3
LIST
FleetSync® & NEXEDGETM AVL & Messaging Software (Windows® 2000/XP compatible),
347.00
Refer to KGS-3 spec sheet for detailed features & requirements.
KAS-10
FleetSync® & NEXEDGETM AVL & Messaging Software (Windows® XP/VISTA compatible),
434.00
Refer to KAS-10 spec sheet for detailed features & requirements.
GPS15L-W
Garmin Internal GPS Receiver Board for FleetSync ® & NEXEDGETM AVL
130.25
Note:
• Conventional & LTR operation
• NEXEDGETM Conventional & Trunking operation
• Requires GA25 MCX GPS antenna
• Refer to 180/NX-Series & KGS-3/KAS-10 In-Depth Technical Manuals for installation, programming &
KGS-3/KAS-10 software setup. Refer to www.garmin.com for GPS-15L-W technical specifications.
• Option: Order L-1098 for Kenwood Long Beach installation
GA25MCX
Garmin On-dash Style Magnetic base GPS Antenna for GPS15L-W
62.00
Note: shipped loose only; Install GA25MCX antenna to GPS15L-W before vehicle install; Refer to 180/NXSeries In-depth Technical Manuals for mobile installation.
LIST
KPG-46AM
KCT-53UM
KPG-111DK
Windows® Programming Software for NX-200/300/700/800
L-1085
L-1087
191.00
86.00
103.25
LIST
NX-700/800 Programming (with basic TX/RX check)
37.50
25.00
L-1090
L-1091
L-1094
L-1098
L-1099
Install & Program CIM-1000K-26 for MDC-1200 in NX-700/800
Install & Program CIM-1000K-26 for GE-Star in NX-700/800
Install Garmin GPS15L-W in NX-Series mobile for FleetSync® AVL
Assemble NX-700/800 with KRK-10 Remote Kit
Page 3 of 3
75.00
75.00
25.00
100.00
42.00
NX-700・800
March 2009
TKR-750 / 850
VHF / UHF Base Station / Repeater
GENERAL FEATURES
• 25-50W (VHF), 25-40 W (UHF) adjustable
• 19" Rack Mount design
• Continuous Transmit Duty (100% @ 25W / 50% @ 50/40W)
• Wide/Narrow Channel Spacing per Channel
• Primary DC input Connector
• Auto-Switched Back-up DC Input Connector
• Rear Test-Speaker Output (4W Output)
• Programmable AUX Input/Output Functions
• Macro-Function AUX Inputs
• DSP Processed QT/DQT
• DSP Processed Companded Audio
• QT/DQT Squelch-Tail Elimination
• Embedded Message w/ Password Protection
• High Stability Oscillatros (TCXO)
50 series repeater includes:
• DC Power Cable
• Rack handles
• Hardware
• Adjustable mounting plate for DC power supply
(DC power supply sold seperately)
MODEL
TKR-750K
TKR-750K2
TKR-850K
TKR-850K2
TKR-850K3
LIST
VHF 146-174 MHz 25-50W, Base-Repeater
VHF 136-150 MHz 25-50W, Base-Repeater
UHF 450-480 MHz 25-40W, Base-Repeater
KMC-27A
KMC-27B
KMC-9C
KES-5
LIST
Heavy-duty noise-canceling mobile hand microphone
Heavy-duty mobile hand microphone
Base Station Desktop microphone
External speaker, Black Case, 40W max. input
POWER SUPPLY
KPS-15
1558.00
1558.00
1663.00
1663.00
1663.00
104.00
42.00
86.00
61.25
LIST
173.00
Note: Kenwood does not install KPS-15's into TKR-750/850 repeaters (dealer install only). Please note the
combined shipping weight of a TKR-750/850 and a KPS-15 exceed the rated capacity of the TKR-750/850
factory cartons.The KPS-15 D.C. power supply is Kenwood approved for use on both the TKR-750 and
TKR-850 repeater units (operating at rated 50% transmit duty-cycle). This does not apply to any other
Kenwood repeater model. The KPS-15 may require a 1 minute warm up at -30 C (due to wet electrolytic
capacitors).
LIST
KPG-46AM
KCT-53UM
KPG-91DK
Windows® Programming Software for TKR-750/850
(DB9M - to - USB Type A connector);
191.00
86.00
#N/A
************************ Call Kenwood Service Corporation Parts Dept. at 800-367-7514 to order the following:
E30-3427-15
DC Power Cable - same as supplied
19.81
INSTALLATION AND TUNING CHARGES
L-916
L-923
LIST
TKR-750/850 Alignment/Programming
30.00
25.00
RX center frequency adjustment for TKR-750/850
Note: This alignment is needed to get maximum performance of the receiver and to reduce the possibility
of desense in the repeater.
Page 1 of 1
TKR-750・850
UHF
TKR-8500 Series Base Stations and Repeaters
400 - 430 MHz and 450 - 512 MHz
GENERAL:
TKR-850/851 UHF Base Stations and Repeaters are integrated systems using TKR-850 or TKR-851 repeaters depending on frequency
sub-band. The TKR-850/851 repeater occupies 2 RU and may be used as a continuous-duty 25W standalone low power station or as
a driver for an external power amplifier. A conventional controller is built into the TKR-850/851 repeaters.
OPTIONS:
Conventional station options include wire line remote control and external RF amplifiers with built-in T-R antenna switching for simplex
operation. Trunking system options include external controllers for LTR and basic MPT-1327 applications; PassPort systems are
available by individual quotation. High performance 4 and 6 cavity BpBr duplexers are listed as options; multichannel combining systems
are quoted on an individual system basis. Power supply options include battery backup with integrated SmartCharger and Low Voltage
Disconnect. Mounting options include 20 RU (42") and 40 RU (77") locking cabinets in addition to 17 RU (3') and 45 RU (7') open equipment racks. Amplifier choices include 40W and 100W options with a 2RU 40A switching power supply, or a 150W option with a 2RU 70A
switching power supply. Custom configurations are also available; contact your Kenwood Systems Regional Sales Manager for more
details.
K1 = 450 - 480 MHz
Order TKR8510SK1 basic repeater
K2 = 480 - 512 MHz
K3 = 400 - 430 MHz
Step 3: Select a Power Supply option.
equipment (Steps 2-5) to determine configuration pricing. Specify frequencies, channel bandwidth and tone assignments
with order.
Page 1 of 6
UHF
400 - 430 MHz and 450 - 512 MHz
LIST
STEP 1 -- TKR-8500 BASIC CONFIGURATION:
TKR8510SK1 BASIC CONFIGURATION, 450 - 480 MHz
$1,854
$2,219
$2,219
TKR-8500 series repeater / base station basic configuration includes 25W continuous duty repeater and internally mounted 20A DC power supply.
Includes factory tuning and staging, one service manual and programming software; ships unmounted.
OPTION KSGA304R: 40W CONTINUOUS DUTY RF AMPLIFIER OPTION FOR REPEATER STATION
$1,691
Repeater station option to include external 40W continuous duty RF amplifier, 400-512MHz. Amplifier occupies 4 RU and includes a 40A, 13.8VDC
power supply (upgrade from basic 20A power supply). Includes factory tuning, wiring and RF cables.
OPTION KSGA304B: 40W CONTINUOUS DUTY RF AMPLIFIER OPTION FOR BASE STATION
$1,747
Base station option to include external 40W continuous duty RF amplifier, 400-512MHz. Amplifier occupies 4 RU and includes a 40A, 13.8VDC
power supply (upgrade from basic 20A power supply) and an integrated T-R antenna switching relay. Includes factory tuning, wiring and RF cables.
$2,235
$2,525
$5,044
$5,919
-$50
$881
For 40W and 100W amplifier options above, upgrade to 35A, 13.8VDC continuous duty switching power supply with front panel metering, built-in
$881
For 40W and 100W amplifier options above, upgrade to 70A, 13.8VDC continuous duty switching power supply with front panel metering; occupies
2 RU. Will power up to 2 channels.
Page 2 of 6
UHF
400 - 430 MHz and 450 - 512 MHz
LIST
$1,263
(battery not included). Will power up to 2 channels. Gel cell batteries are available separately; please contact your Kenwood Systems Regional Sales
Manager for details.
$381
For 150W Amplifier options above, upgrade to 70A, 13.8VDC continuous duty switching power supply with front panel metering, built-in
$1,157
Standard 3' aluminum equipment rack providing 17 RU vertical mounting. Pricing includes equipment installation, hardware, cabling and
wire management materials, and cushioned shipping crate.
$1,250
$1,750
Locking cabinet, 42"H x 22"W x 24"D, providing 20 RU vertical mounting, solid front door, louvered rear door, perforated top panel.
Pricing includes equipment installation, hardware, cabling and wire management materials, and cushioned shipping crate.
$2,659
$63
$445
$93
$683
OPTION KSGTN02A: 2 CHANNEL TONE TERMINATION PANEL
2 channel tone termination panel, 2 or 4 wire, 600 Ohm balanced audio with monitor, occupies 1 RU.
$683
OPTION KSGTN02N: N-SERIES CHANNEL TONE TERMINATION PANEL
N-Series channel tone termination panel, 2 or 4 wire, 600 Ohm balanced audio with monitor, AGC automatic line-leveling, occupies 1 RU.
OPTION KSGTN10A: 10 CHANNEL DISCRETE TONE TERMINATION PANEL
$1,254
10 channel (discrete) tone termination panel, 2 or 4 wire, 600 Ohm balanced audio with monitor, occupies 1 RU.
Page 3 of 6
UHF
400 - 430 MHz and 450 - 512 MHz
LIST
$1,324
OPTION KSGTN16A: 16 CHANNEL BCD TONE TERMINATION PANEL
16 channel (BCD) tone termination panel, 2 or 4 wire, 600 Ohm balanced audio with monitor, occupies 1 RU.
$393
OPTION KSGTDC2A: DC TERMINATION PANEL
DC termination panel, 2 or 4 wire, 600 Ohm balanced audio with monitor, occupies 1 RU. Specify required DC current settings at time of order.
$367
1 channel receive audio line driver panel, 2 wire, 600 Ohm balanced output, occupies 1 RU. May also be configured to fully support
a 4-wire E&M interface application.
EXTERNAL TRUNKING CONTROLLER OPTIONS:
$1,586
OPTION KSGC040L: LTR DISPATCH TRUNKING CONTROLLER
Raider LTR dispatch-only trunking controller. Includes setup, tuning, and interface cable.
$3,327
OPTION KSGC041L: RAIDER XTREME LTR DISPATCH TRUNKING CONTROLLER
Raider Xtreme, single-site PassPort dispatch trunking controller for UHF systems, up to 20 channels per site. Includes setup, tuning, and interface cable.
Standard features include ESN validation, radio stun and kill, and airtime logging. Contact your systems regional manager for optional selective call feature.
$3,016
OPTION KSGC050L: LTR DISPATCH & INTERCONNECT TRUNKING CONTROLLER
Marauder LTR dispatch and interconnect trunking controller. Includes setup, tuning, and interface cable.
$1,850
Model 452 LTR dispatch-only trunking controller. Includes setup, tuning, and interface cable.
$3,242
Model 459 LTR dispatch and interconnect trunking controller. Includes setup, tuning, and interface cable.
$4,599
OPTION KSGC807M: BASIC MPT-1327 TRUNKING CONTROLLER
Model 807 MPT trunking controller. Includes setup, tuning, and interface cable.
$6,265
OPTION KSGC827M: BASIC MPT-1327 INTERCONNECT CONTROLLER
$9,765
OPTION KSGC844M: BASIC MPT-1327 MULTI-SITE CONTROLLER
Model 844 MPT multi-site controller. Includes setup, tuning, and interface cable.
$9,765
OPTION KSGC427M: BASIC MPT-1327 PERIPHERAL EQUIPMENT INTERFACE
Model 427 MPT peripheral equipment interface with MAP-27. Includes setup, tuning, and interface cable.
$3,080
OPTION KSGD3P1B: 6 CAVITY UHF BpBr DUPLEXER
6 cavity Bandpass/Bandreject duplexer, 250W continuous duty, minimum TX-RX spacing 3 MHz. Includes RF interface cables, mounting, and
factory tuning. Duplexers are fully integrated and tested during system staging.
$1,693
OPTION KSGD3P2B: 4 CAVITY UHF BpBr DUPLEXER (450 - 470 MHz ONLY)
Page 4 of 6
UHF
400 - 430 MHz and 450 - 512 MHz
LIST
$323
OPTION KSGOMOD1: BASIC SITE MANAGEMENT MODEM
Generic site management modem, 2400 bps. For use with LTR controllers, includes interface cable, occupies 1 RU.
$961
OPTION KSGOMOD2: HIGH PERFORMANCE SITE MANAGEMENT MODEM
High performance site management modem designed for extra stability in high RF environments, 2400 bps. For use with LTR controllers, includes
interface cable, occupies 1 RU.
$8,840
$1,345
$855
Internal pilot tone generator for use with voting systems, supplies 600 Ohm balanced 2 wire audio, occupies 1 RU.
$191.00
OPTION KPG-46AM: KPG-46AM PROGRAMMING CABLE
OPTION KCT-53UM: KCT-53UM DB9M TO USB TYPE A CONNECTOR
$86.00
OPTION B51-8557-30: TKR-850 SERVICE MANUAL
$53.00
$37.00
N/A
OPTION KPG-91DK: KPG-91DK PROGRAMMING SOFTWARE
Note: Pre-Selectors, Multi-Couplers, Combiners, Outdoor Cabinets, and other items are available by special order.
Page 5 of 6
DEALER:
DLR #:
PHONE:
CONTACT:
FAX:
E-MAIL:
SHIP TO:
CITY:
ST:
PREPARED BY:
ZIP:
DATE:
PAGE
OF
TKR/TKB/KSG/NXR
CONFIGURATION
TRANSMIT POWER
-
CONTROL TYPE
W
B
AUDIO LEVELS
2W SIM / 4W DUP
/
P
TRANSMITTER
CHAN
W/N
CHAN 1 RX FREQ
TX CTCSS / DCS
CSQ
CHAN 2 RX FREQ
W/N
TX CTCSS / DCS
CSQ
CHAN 3 RX FREQ
.
RX CTCSS / DCS
CSQ
W/N
RX CTCSS / DCS
CSQ
W/N
RX CTCSS / DCS
CSQ
W/N
RX CTCSS / DCS
CSQ
W/N
RX CTCSS / DCS
CSQ
.
W/N
CHAN 4 TX FREQ
TX CTCSS / DCS
CSQ
CHAN 4 RX FREQ
.
.
CHAN 5 TX FREQ
W/N
TX CTCSS / DCS
CSQ
CHAN 5 RX FREQ
.
5
W/N
.
CHAN 3 TX FREQ
4
CHAN
CSQ
.
3
CHAN
TX CTCSS / DCS
.
CHAN 2 TX FREQ
2
CHAN
W/N
.
1
CHAN
RECEIVER
CHAN 1 TX FREQ
.
CONTROLLER MODEL
CHAN
1
CHAN
2
CHAN
3
CHAN
4
CHAN
5
CONTROLLER
FIRMWARE VERSION
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
KSG CONTROLLER
KSG CONTROLLER
KSG CONTROLLER
KSG CONTROLLER
KSG -
Yes
No
UHF
TKR-8400 Series High Performance Base Stations and Repeaters
450 - 512 MHz
GENERAL:
The TKR-840 repeater occupies 1 RU and may be used as a 5W standalone low power station or as a driver for an external power
amplifier. A conventional controller and a digital POCSAG paging transmitter are built into the TKR-840 repeater; paging terminal is not
included.
OPTIONS:
available by individual quotation. High performance 4 and 6 cavity BpBr duplexers are listed as options; multichannel combining systems
are quoted on an individual system basis. Power supply options include battery backup with integrated SmartCharger and Low Voltage
details.
K1 = 450 - 480 MHz
K2 = 480 - 512 MHz
with order.
Page 1 of 6
UHF
450 - 512 MHz
LIST
$3,510
$3,510
TKR-8400 repeater / base station basic configuration includes 5W continuous duty repeater and 19-inch rack mountable 20A DC power supply.
OPTION KSGMODP1 CIRCUIT MODIFICATION REQUIRED FOR USE WITH PASSPORT-NTS PROTOCOL
$158
OPTION KSGA304S: 40W CONTINUOUS DUTY RF AMPLIFIER OPTION FOR REPEATER STATION
$1,561
power supply. Includes factory tuning, wiring and RF cables.
OPTION KSGA304C: 40W CONTINUOUS DUTY RF AMPLIFIER OPTION FOR BASE STATION
$1,683
$2,107
$2,480
$4,924
$5,799
-$50
$881
$881
Page 2 of 6
UHF
450 - 512 MHz
LIST
$1,263
$381
$1,157
$1,250
$1,750
$2,659
$63
$445
$93
$683
$683
$1,254
Page 3 of 6
UHF
450 - 512 MHz
LIST
$1,324
$393
$367
$1,586
$3,327
Standard features include ESN validation, radio stun and kill, and airtime logging. Contact your systems regional manager for optional selective call feature.
$3,016
$1,850
$3,242
$4,599
$6,265
$9,765
$9,765
$3,080
$1,693
Page 4 of 6
UHF
450 - 512 MHz
LIST
$323
$961
$8,840
$1,345
$855
$191.00
$86.00
$53.00
N/A
Page 5 of 6
DEALER:
DLR #:
PHONE:
CONTACT:
FAX:
E-MAIL:
SHIP TO:
CITY:
ST:
PREPARED BY:
ZIP:
DATE:
PAGE
OF
TKR/TKB/KSG/NXR
CONFIGURATION
TRANSMIT POWER
-
CONTROL TYPE
W
B
AUDIO LEVELS
2W SIM / 4W DUP
/
P
TRANSMITTER
CHAN
W/N
CHAN 1 RX FREQ
TX CTCSS / DCS
CSQ
CHAN 2 RX FREQ
W/N
TX CTCSS / DCS
CSQ
CHAN 3 RX FREQ
.
RX CTCSS / DCS
CSQ
W/N
RX CTCSS / DCS
CSQ
W/N
RX CTCSS / DCS
CSQ
W/N
RX CTCSS / DCS
CSQ
W/N
RX CTCSS / DCS
CSQ
.
W/N
CHAN 4 TX FREQ
TX CTCSS / DCS
CSQ
CHAN 4 RX FREQ
.
.
CHAN 5 TX FREQ
W/N
TX CTCSS / DCS
CSQ
CHAN 5 RX FREQ
.
5
W/N
.
CHAN 3 TX FREQ
4
CHAN
CSQ
.
3
CHAN
TX CTCSS / DCS
.
CHAN 2 TX FREQ
2
CHAN
W/N
.
1
CHAN
RECEIVER
CHAN 1 TX FREQ
.
CONTROLLER MODEL
CHAN
1
CHAN
2
CHAN
3
CHAN
4
CHAN
5
CONTROLLER
FIRMWARE VERSION
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
KSG CONTROLLER
KSG CONTROLLER
KSG CONTROLLER
KSG CONTROLLER
KSG -
Yes
No
VHF High Band
136 - 174 MHz
GENERAL:
TKR-750/751 VHF High Band Base Stations and Repeaters are integrated systems using TKR-750 or TKR-751 repeaters depending
on frequency sub-band. The TKR-750/751 repeater occupies 2 RU and may be used as a continuous-duty 25W standalone low power
station or as a driver for an external power amplifier. A conventional controller is built into the TKR-750/751 repeaters.
OPTIONS:
available by individual quotation. High performance 6 cavity BpBr duplexers are listed as options; multichannel combining systems are
quoted on an individual system basis. Power supply options include battery backup with integrated SmartCharger and Low Voltage
details.
K1 = 146 - 174 MHz
K2 = 136 - 146 MHz
with order.
Page 1 of 6
VHF High Band
136 - 174 MHz
LIST
$1,794
$2,109
TKR-7500 series repeater / base station basic configuration includes 25W continuous duty repeater and internally mounted 20A DC power supply.
$1,750
$2,100
$2,310
$2,525
$4,310
$5,185
-$50
$881
$881
$1,263
Page 2 of 6
VHF High Band
136 - 174 MHz
LIST
$381
$1,157
$1,250
$1,750
$2,659
$63
$445
$93
$683
$683
$1,254
$1,324
$393
Page 3 of 6
VHF High Band
136 - 174 MHz
LIST
$367
$1,586
$3,016
$1,850
$3,242
$4,599
$6,265
$9,765
$9,765
$3,080
OPTION KSGD2P1B: 6 CAVITY VHF BpBr DUPLEXER
6 cavity Bandpass/Bandreject duplexer, 350W continuous duty, minimum TX-RX spacing 400 KHz. Includes RF interface cables, mounting, and
$323
$961
$8,840
$1,345
Page 4 of 6
VHF High Band
136 - 174 MHz
LIST
$855
$191.00
$86.00
$53.00
$37.00
N/A
Page 5 of 6
DEALER:
DLR #:
PHONE:
CONTACT:
FAX:
E-MAIL:
SHIP TO:
CITY:
ST:
PREPARED BY:
ZIP:
DATE:
PAGE
OF
TKR/TKB/KSG/NXR
CONFIGURATION
TRANSMIT POWER
-
CONTROL TYPE
W
B
AUDIO LEVELS
2W SIM / 4W DUP
/
P
TRANSMITTER
CHAN
W/N
CHAN 1 RX FREQ
TX CTCSS / DCS
CSQ
CHAN 2 RX FREQ
W/N
TX CTCSS / DCS
CSQ
CHAN 3 RX FREQ
.
RX CTCSS / DCS
CSQ
W/N
RX CTCSS / DCS
CSQ
W/N
RX CTCSS / DCS
CSQ
W/N
RX CTCSS / DCS
CSQ
W/N
RX CTCSS / DCS
CSQ
.
W/N
CHAN 4 TX FREQ
TX CTCSS / DCS
CSQ
CHAN 4 RX FREQ
.
.
CHAN 5 TX FREQ
W/N
TX CTCSS / DCS
CSQ
CHAN 5 RX FREQ
.
5
W/N
.
CHAN 3 TX FREQ
4
CHAN
CSQ
.
3
CHAN
TX CTCSS / DCS
.
CHAN 2 TX FREQ
2
CHAN
W/N
.
1
CHAN
RECEIVER
CHAN 1 TX FREQ
.
CONTROLLER MODEL
CHAN
1
CHAN
2
CHAN
3
CHAN
4
CHAN
5
CONTROLLER
FIRMWARE VERSION
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
KSG CONTROLLER
KSG CONTROLLER
KSG CONTROLLER
KSG CONTROLLER
KSG -
Yes
No
VHF
TKR-7400P P25 Repeater
146 - 162 MHz
GENERAL:
The TKR-7400P repeater and the KSGCP401 external P25 controller occupy 2 RU and may be used as a 5W standalone low power station
or as a driver for an external power amplifier. The P25 controller includes one channel card and an option to add up to three more for a total
of four.One channel card is required for each repeater. The TKR-7400P is a P25 conventional repeater and cannot be cofigured for base
base station operation.
OPTIONS:
Conventional station options include up to three addional channel cards. High performance 4 and 6 cavity BpBr duplexers are listed as
options; multichannel combining systems are quoted on an individual system basis. Power supply options include battery backup with
integrated SmartCharger and Low Voltage disconnect. Mounting options include 20 RU (42") and 40 RU (77") locking cabinets in addition
to 17 RU (3') and 45 RU (7') open equipment racks. Amplifier choices include 40W and 100W options with a 2RU 40A switching power
supply, or a 150W option with a 2RU 70A switching power supply. Custom configurations are also available; contact your Kenwood
Systems
y
Regional
g
Sales Manager
g for more details.
Channel cards can be used for existing 40 series repeaters, existing repeaters will need to be sent to Kenwood to be modified and
interfaced. The labor code for the modification must be ordered with the channel card.
K1 = 146 - 162 MHz
Page 1 of 6
VHF
146 - 162 MHz
LIST
STEP 1 -- TKR-740 REPEATER
$3,417
Includes factory tuning and staging, one service manual and programming software.
KSGCP401 P25 CONTROLLER
$7,945
KSGCP401 includes one channel card housed in a 1 RU 19-inch rack mountable housing with cable. Maximum 4 channel cards.
$6,112
KSGCP402 CHANNEL CARD
Channel card and cable used for additional repeaters at the same site.
KSGMODP2 CIRCUIT MODIFICATION FOR EXISTING REPEATERS
$750
Modification to circuits for P25 operation. This modification must be done by Kenwood. It is not a field upgrade
$1,625
Repeater station upgrade to include external 50W continuous duty RF amplifier, 136-174MHz. Amplifier occupies 4 RU and includes a 40A, 13.8VDC
$2,180
$4,191
-$50
$881
$881
$1,263
$381
Page 2 of 6
VHF
146 - 162 MHz
LIST
$1,157
$1,250
$1,750
$2,659
$63
C bi t upgrade
Cabinet
d tto solid
lid ttop panel;l replaces
l
standard
t d d perforated
f t d ttop panel.l
$445
$93
$3,080
$191.00
$86.00
$53.00
N/A
Page 3 of 6
UHF
450 - 480 MHz
GENERAL:
The TKR-8400P repeater and the KSGCP401 external P25 controller occupy 2 RU and may be used as a 5W standalone low power station
or as a driver for an external power amplifier. The P25 controller includes one channel card and an option to add up to three more for a total
of four. One channel card is required for each repeater. The TKR-8400P is a P25 conventional repeater and cannot be configured for
base station operation.
OPTIONS:
Conventional station options include up to three addional channel cards. High performance 4 and 6 cavity BpBr duplexers are listed as
options; multichannel combining systems are quoted on an individual system basis. Power supply options include battery backup with
integrated SmartCharger and Low Voltage disconnect. Mounting options include 20 RU (42") and 40 RU (77") locking cabinets in addition
t 17 RU (3') and
to
d 45 RU (7') open equipment
i
t racks.
k Amplifier
A lifi choices
h i
iinclude
l d 40W and
d 100W options
ti
with
ith a 2RU 40A switching
it hi power
supply, or a 150W option with a 2RU 70A switching power supply. Custom configurations are also available; contact your Kenwood
Systems Regional Sales Manager for more details.
Channel cards can be used for existing 40 series repeaters, existing repeaters will need to be sent to Kenwood to be modified and
interfaced. The labor code for the modification must be ordered with the channel card.
K1 = 450 - 480 MHz
Order TKR8400PSK1 basic repeater
Page 4 of 6
UHF
450 - 480 MHz
LIST
TKR8400PSK1 BASIC CONFIGURATION, 450 - 480 MHz
$3,510
TKR-8400P repeater basic configuration includes 5W continuous duty repeater and 19-inch rack mountable 20A DC power supply.
Includes factory tuning and staging, one service manual and programming software.
KSGCP401 P25 CONTROLLER
$7,945
KSGCP401 includes one channel card housed in a 1 RU 19-inch rack mountable housing with cable. Maximum 4 channel cards.
$6,112
KSGCP402 CHANNEL CARD
Channel card and cable used for additional repeaters at the same site.
$750
KSGMODP2 CIRCUIT MODIFICATION FOR EXISTING REPEATERS
Modification to circuits for P25 operation. This modification must be done by Kenwood. It is not a field upgrade
$1,561
$2,107
$4,924
-$50
$881
$881
$1,263
$381
Page 5 of 6
UHF
450 - 480 MHz
$1,157
$1,250
$1,750
$2,659
$63
$445
$93
$3,080
$1,693
$191.00
$86.00
$53.00
N/A
Page 6 of 6
VHF High Band
136 - 174 MHz
GENERAL:
The TKR-740 repeater occupies 1 RU and may be used as a 5W standalone low power station or as a driver for an external power amplifier.
A conventional controller and a digital POCSAG paging transmitter are built into the TKR-740 repeater; paging terminal is not included.
OPTIONS:
operation. Trunking system options include external controllers for LTR and basic MPT-1327 applications; PassPort systems are available by
individual quotation. High performance 6 cavity BpBr duplexers are listed as options; multichannel combining systems are quoted on an
individual system basis. Power supply options include battery backup with integrated SmartCharger and Low Voltage Disconnect. Mounting
options include 20 RU (42") and 40 RU (77") locking cabinets in addition to 17 RU (3') and 45 RU (7') open equipment racks. Amplifier choices
include 50W and 110W options with a 2RU 40A switching power supply, or a 150W option with a 2RU 70A switching power supply. Custom
configurations are also available; contact your Kenwood Systems Regional Sales Manager for more details.
K1 = 146 - 162 MHz
K2 = 158 - 174 MHz
K3 = 136 - 150 MHz
Step 6: Add the basic configuration (Step 1) to the desired RF amplifier, power supply, mounting configuration and optional equipment
(Steps 2-5) to determine configuration pricing. Specify frequencies, channel bandwidth and tone assignments with order.
LIST
STEP 1 -- TKR-740 REPEATER
$3,417
$3,417
$3,417
OPTION KSGMODP1 CIRCUIT MODIFICATION REQUIRED FOR USE WITH PASSPORT-NTS PROTOCOL
Page 1 of 6
$158
VHF High Band
136 - 174 MHz
LIST
$1,625
$1,975
Base station upgrade to include external 50W continuous duty RF amplifier, 136-174MHz. Amplifier occupies 4 RU and includes a 40A, 13.8VDC
$2,180
$2,420
$4,191
$5,065
-$50
$881
$881
$1,263
$381
Page 2 of 6
VHF High Band
136 - 174 MHz
LIST
$1,157
$1,250
$1,750
$2,659
$63
$445
$93
$683
$683
$1,254
$1,324
$393
$367
Page 3 of 6
VHF High Band
136 - 174 MHz
LIST
$1,586
$3,016
$1,850
$3,242
$4,599
$6,265
$9,765
$9,765
$3,080
$323
$961
$8,840
$1,345
$855
Page 4 of 6
VHF High Band
136 - 174 MHz
LIST
$191.00
$86.00
$53.00
N/A
Page 5 of 6
DEALER:
DLR #:
PHONE:
CONTACT:
FAX:
E-MAIL:
SHIP TO:
CITY:
ST:
PREPARED BY:
ZIP:
DATE:
PAGE
OF
TKR/TKB/KSG/NXR
CONFIGURATION
TRANSMIT POWER
-
CONTROL TYPE
W
B
AUDIO LEVELS
2W SIM / 4W DUP
/
P
TRANSMITTER
CHAN
W/N
CHAN 1 RX FREQ
TX CTCSS / DCS
CSQ
CHAN 2 RX FREQ
W/N
TX CTCSS / DCS
CSQ
CHAN 3 RX FREQ
.
RX CTCSS / DCS
CSQ
W/N
RX CTCSS / DCS
CSQ
W/N
RX CTCSS / DCS
CSQ
W/N
RX CTCSS / DCS
CSQ
W/N
RX CTCSS / DCS
CSQ
.
W/N
CHAN 4 TX FREQ
TX CTCSS / DCS
CSQ
CHAN 4 RX FREQ
.
.
CHAN 5 TX FREQ
W/N
TX CTCSS / DCS
CSQ
CHAN 5 RX FREQ
.
5
W/N
.
CHAN 3 TX FREQ
4
CHAN
CSQ
.
3
CHAN
TX CTCSS / DCS
.
CHAN 2 TX FREQ
2
CHAN
W/N
.
1
CHAN
RECEIVER
CHAN 1 TX FREQ
.
CONTROLLER MODEL
CHAN
1
CHAN
2
CHAN
3
CHAN
4
CHAN
5
CONTROLLER
FIRMWARE VERSION
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
KSG CONTROLLER
KSG CONTROLLER
KSG CONTROLLER
KSG CONTROLLER
KSG -
Yes
No
TKB-751/851 and TKR-751/851
VHF and UHF Low Power Base Stations and Repeaters
GENERAL:
The TKB-751/851 and TKR-751/851 Low Power Base Stations and Repeaters offer the following features.
1-25 Watt UHF and VHF
4 Watt Front Panel Speaker Audio
Continuous Duty Operation
BCD Remote Channel Selection (4 Lines up to 15 Channels)
19" Rack Mount
Programmable AUX Input/Output Functions
Wide/Narrow Band (Programmable per Channel)
Built-In Cooling Fan
Battery Back-Up Capable
Macro-Function AUX Inputs
Back-Up Battery Warning/Operating Tone
Selectable Toggle/Momentary on AUX Input Ports
Rear Accessory/Logic Controller Connector
DTMF Over-The-Air Remote Function and AUX Output Control
Rear Test Speaker - AUX Connector
DSP Processed QT/DQT
High Stability Oscillators (TCXO)
DSP Processed Companded Audio
Windows 98/2000/ME/XP Compatible PC Programming and Tuning
CTCSS Squelch-Tall Elimination
2 Years Parts and Labor Warranty
Flash Memory
OPTIONS:
When used as a Base Station, the TKB-751/851 also offers the following features.
16 Channel
6 Lighted, Customizable Front Panel PF Keys
Simplex or Full Duplex Operation
Local Takeover/Remote Function
Built-In Antenna Switch for Simplex/Single Antenna Operation
Front Panel Channel Up/Down PF Keys
Priority Scan
Local Volume Control Knob
Remote Control Inputs
Front 8-Pin Microphone Jack
7-Segment, 2-Character Channel and Scan LED Indicator
Front Panel Speaker
Programmable 2 Character Alphanumeric Channel Designators
Voice Encryption Option Port
Power/Transmit/Busy LED Indicators
When used as a Repeater, the TKR-751/851 also offers the following features.
Full Duplex Operation
Courtesy Tone
16 Built-In Community CTCSS/DCS Tone/Code Pairs
Repeat Enable/Disable
Repeat Function
CW Transmitter ID
External Controller Interface
Repeat Hold Timer (Hang Timer)
Conventional or Trunking Controller Compatible
Time Out Timer
Page 1 of 3
TKB-751/851 and TKR-751/851
VHF and UHF Low Power Base Stations and Repeaters
LIST
BASE STATIONS
$1,720
TKB8510PS BASIC CONFIGURATION, 450 - 480 MHz
TKB8510PS base station basic configuration includes 1-25W 100% duty radio, internal T-R relay, internally mounted 20A power supply, programming,
and tuning. Ships unmounted.
$1,617
TKB7510PS BASIC CONFIGURATION, 146 - 174 MHz
TKB7510PS base station basic configuration includes 1-25W 100% duty radio, internal T-R relay, internally mounted 20A power supply, programming,
and tuning. Ships unmounted.
REPEATERS
$1,720
TKR8510PS BASIC CONFIGURATION, 450 - 480 MHz
TKR8510PS repeater basic configuration includes 1-25W 100% duty repeater, internally mounted 20A power supply, programming, and tuning. Ships
unmounted.
$2,253
TKR8510PSD BASIC CONFIGURATION, 450 - 480 MHz WITH INTERNAL DUPLEXER
TKR8510PSD repeater basic configuration includes 1-25W 100% duty repeater, internally mounted 20A power supply, internal low power duplexer,
programming, and tuning. Ships unmounted.
$1,617
TKR7510PS BASIC CONFIGURATION, 146 - 174 MHz
TKR7510PS repeater basic configuration includes 1-25W 100% duty repeater, internally mounted 20A power supply, programming, and tuning. Ships
unmounted.
$2,150
TKR7510PSD BASIC CONFIGURATION, 146 - 174 MHz WITH INTERNAL DUPLEXER
TKR7510PSD repeater basic configuration includes 1-25W 100% duty repeater, internally mounted 20A power supply, internal low power duplexer,
programming, and tuning. Ships unmounted. NOTE: Duplexer model requires a TX-RX frequency spacing of 5 MHz or greater.
BASE STATION AND REPEATER OPTIONS
-$50
Delete internally mounted 20A power supply from basic station configuration.
Desktop Enclosure Units - High-quality black laminate finish; easily assembled with included hardware.
$242
$260
OPTION KSGMT30001: 2RU DESKTOP ENCLOSURE - 16" deep by 20.5" wide by 5" high.
OPTION KSGMT30004: 4RU DESKTOP ENCLOSURE - 16" deep by 20.5" wide by 8.5" high.
OPTION KMC-9C: KMC-9C DESKTOP MICROPHONE
$86.00
$37.00
$37.00
$191.00
$86.00
N/A
Note: External power amplifiers vary; see pages 35-36 for high-power base station and repeater amplifier configurations. For complete rack and
cabinet enclosure options, see Components section. Please contact your Kenwood Systems Regional Sales Manager for more information.
Page 2 of 3
DEALER:
DLR #:
PHONE:
CONTACT:
FAX:
E-MAIL:
SHIP TO:
CITY:
ST:
PREPARED BY:
ZIP:
DATE:
PAGE
OF
TKR/TKB/KSG/NXR
CONFIGURATION
TRANSMIT POWER
-
CONTROL TYPE
W
B
AUDIO LEVELS
2W SIM / 4W DUP
/
P
TRANSMITTER
CHAN
W/N
CHAN 1 RX FREQ
TX CTCSS / DCS
CSQ
CHAN 2 RX FREQ
W/N
TX CTCSS / DCS
CSQ
CHAN 3 RX FREQ
.
RX CTCSS / DCS
CSQ
W/N
RX CTCSS / DCS
CSQ
W/N
RX CTCSS / DCS
CSQ
W/N
RX CTCSS / DCS
CSQ
W/N
RX CTCSS / DCS
CSQ
.
W/N
CHAN 4 TX FREQ
TX CTCSS / DCS
CSQ
CHAN 4 RX FREQ
.
.
CHAN 5 TX FREQ
W/N
TX CTCSS / DCS
CSQ
CHAN 5 RX FREQ
.
5
W/N
.
CHAN 3 TX FREQ
4
CHAN
CSQ
.
3
CHAN
TX CTCSS / DCS
.
CHAN 2 TX FREQ
2
CHAN
W/N
.
1
CHAN
RECEIVER
CHAN 1 TX FREQ
.
CONTROLLER MODEL
CHAN
1
CHAN
2
CHAN
3
CHAN
4
CHAN
5
CONTROLLER
FIRMWARE VERSION
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
KSG CONTROLLER
KSG CONTROLLER
KSG CONTROLLER
KSG CONTROLLER
KSG -
Yes
No
LOW BAND
29.7 - 50 MHz
GENERAL:
TKB-6900 Series Low Band Base Stations are built around the TK-690 high performance 110W radio. The TK-690 transceiver is
mounted in a 2 RU enclosure which includes forced air cooling and option bays for two peripheral circuit boards. The basic
configuration includes a 2 channel tone termination panel (2 or 4 wire audio). Equipment may be mounted in a cabinet enclosure or
open rack, and may be used either by itself (50W continuous duty or 110W at 20% duty cycle) or as a driver for an external continuous
duty RF amplifier (100W or 300W).
OPTIONS:
Power supply options include battery backup with integrated SmartCharger and Low Voltage Disconnect. Mounting options include
20 RU (42") and 40 RU (77") locking cabinets in addition to 17 RU (3') and 45 RU (7') open equipment racks. External connections are
RJ-11 for phone line, DB-25 for access to the internal chassis bus, & type N-female for RF. T-R simplex antenna switching is included in
the basic unit as well as in all external amplifiers. Other configurations are also available on a special order basis; please contact your
Kenwood Systems Regional Sales Manager for more details.
K1 = 29.7 - 37.0MHz
K2 = 35.0 - 43.0MHz
K3 = 39.0 - 50.0MHz
equipment (Steps 2-5) to determine configuration pricing. Specify frequencies and tone assignments with order.
Page 1 of 5
LOW BAND
29.7 - 50 MHz
LIST
STEP 1 -- TKB-6900 BASIC CONFIGURATION:
$3,297
$3,297
$3,297
TKB-6900 low band base station basic configuration includes 40A DC power supply and 2 channel tone termination panel. Base station provides
50W continuous duty, 110W at 20% duty cycle. Includes factory tuning and staging, one service manual, and programming software; ships unmounted.
$2,171
Upgrade to include external 100W continuous duty RF amplifier, 29.7-50.0MHz. Amplifier occupies 4 RU and is powered by the 40A, 13.8VDC
power supply included in the basic station configuration. Includes factory tuning, RF cables, wiring and internal T-R antenna relay.
$6,499
Upgrade to include external 300W continuous duty RF amplifier, 29.7-50.0MHz. Amplifier occupies 8 RU and is powered by a 70A, 13.8VDC power
supply. Includes factory tuning, RF cables, wiring and internal T-R antenna relay.
-$83
$881
$881
For 100W amplifier options above, upgrade to 70A, 13.8VDC continuous duty switching power supply with front panel metering; occupies 2 RU. Will
$1,263
$381
For 300W Amplifier option above, upgrade to 70A, 13.8VDC continuous duty switching power supply with front panel metering, built-in
$1,157
$1,250
Page 2 of 5
LOW BAND
29.7 - 50 MHz
LIST
$1,750
$2,659
$63
$445
$93
$393
OPTION KSGTN10B: 10 CHANNEL DISCRETE TONE TERMINATION PANEL UPGRADE
Upgrade to 10 channel (Discrete) tone termination panel, 2 or 4 wire, 600 Ohm balanced audio with monitor, installs in one station option bay.
$774
OPTION KSGTN16B: 16 CHANNEL BCD TONE TERMINATION PANEL UPGRADE
Upgrade to 16 channel (BCD) tone termination panel, 2 or 4 wire, 600 Ohm balanced audio with monitor, occupies 1 RU.
$0
OPTION KSGTDC2B: 2 CHANNEL DC TERMINATION PANEL OPTION
Replace 2 channel tone termination channel with 2 channel DC termination panel, 2 or 4 wire, 600 Ohm balanced audio with monitor, installs in one
station option bay. Specify required DC current settings at time of order.
$0
Replace 2 channel tone termination channel with 1 channel receive audio line driver panel, 2 wire, 600 Ohm balanced output, installs in one station
option bay. May also be configured to fully support a 4-wire E&M interface application.
$8,840
$1,345
$855
Internal pilot tone generator for use with voting systems, supplies 600 Ohm balanced 2 wire audio, installs in one station option bay.
Page 3 of 5
LOW BAND
29.7 - 50 MHz
LIST
$131
OPTION KSGOCWID: MORSE CODE IDENTIFIER
Internal automatic CWID Morse Code Identifier (addition to basic station), installs inside basic station enclosure. Specify call sign at time of order.
Includes programmer and cable.
$114.50
$86.00
OPTION B51-8460-10: TK-690 SERVICE MANUAL
$53.00
N/A
Note: Outdoor cabinets and other items are available by special order.
Page 4 of 5
DEALER:
DLR #:
PHONE:
CONTACT:
FAX:
E-MAIL:
SHIP TO:
CITY:
ST:
PREPARED BY:
ZIP:
DATE:
PAGE
OF
TKR/TKB/KSG/NXR
CONFIGURATION
TRANSMIT POWER
-
CONTROL TYPE
W
B
AUDIO LEVELS
2W SIM / 4W DUP
/
P
TRANSMITTER
CHAN
W/N
CHAN 1 RX FREQ
TX CTCSS / DCS
CSQ
CHAN 2 RX FREQ
W/N
TX CTCSS / DCS
CSQ
CHAN 3 RX FREQ
.
RX CTCSS / DCS
CSQ
W/N
RX CTCSS / DCS
CSQ
W/N
RX CTCSS / DCS
CSQ
W/N
RX CTCSS / DCS
CSQ
W/N
RX CTCSS / DCS
CSQ
.
W/N
CHAN 4 TX FREQ
TX CTCSS / DCS
CSQ
CHAN 4 RX FREQ
.
.
CHAN 5 TX FREQ
W/N
TX CTCSS / DCS
CSQ
CHAN 5 RX FREQ
.
5
W/N
.
CHAN 3 TX FREQ
4
CHAN
CSQ
.
3
CHAN
TX CTCSS / DCS
.
CHAN 2 TX FREQ
2
CHAN
W/N
.
1
CHAN
RECEIVER
CHAN 1 TX FREQ
.
CONTROLLER MODEL
CHAN
1
CHAN
2
CHAN
3
CHAN
4
CHAN
5
CONTROLLER
FIRMWARE VERSION
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
KSG CONTROLLER
KSG CONTROLLER
KSG CONTROLLER
KSG CONTROLLER
KSG -
Yes
No
UHF
NXR-8000 Series
High Performance Base Stations and Repeaters
400 - 512 MHz
GENERAL:
NXR-8000 UHF Base Stations and Repeaters are integrated systems. The NXR-800 repeater occupies 1 RU and may be used as a
standalone 5W low-power station or in conjunction with an external power amplifier. The NXR-800 can be programmed to operate in
the analog mode at 25 KHz or 12.5 KHz, and in the digital mode at 12.5 KHz or 6.25 KHz.
Mobiles and portables ordered at the same time as an integrated trunking system may be programmed, tested and optimized with the
system prior to shipment. This service will be provided at no charge as a limited time offer. Fees for this service may be applied on
future orders. Programming information is required to properly configure each system. Please contact your Kenwood Systems
Regional Manager for assistance.
OPTIONS:
Station options include external amplifiers with built-in T/R antenna switching for simplex operation, wire line remote control, and power
supply options such as integrated SmartCharger and low voltage disconnect for battery backup applications. High performance 6
cavity BpBr duplexers are also listed, while multi-channel combining systems are quoted on an individual system basis.
Mounting options include 20 RU (42") and 40 RU (77") locking cabinets in addition to 17 RU (3') and 45 RU (7') open equipment racks.
Basic NXR8000 repeater configuration includes a 2 RU, 20A, 13.8VDC switching power supply (47-63Hz, 115 or 230VAC); 40W and
100W amplifier options include upgrade to 40A switching power supply (40A model also occupies 2 RU), while a 150W amplifier option
includes an upgrade to a 2 RU, 70A switching power supply. Custom configurations are also available; contact your Kenwood
Required trunking options include enabling of the NXR-800 trunking feature, plus system management software that includes a master
USB key & activation file, which hold a license ID unique to each system. This system manager software permits a system administrator
to change critical features and permissions. Secondary, restricted-level service keys that manage less critical system parameters are
also available.
Each trunking system, including single-site systems, will require an Ethernet switch/router. This router will also serve as the multi-site
network interface when required. NOTE: Recommended models are listed herein, but most commercially available IP equipment is
compatible as well.
K = 450 - 480 MHz
Order NXR8000SK1 basic repeater
K2 = 480 - 512 MHz
K3 = 400 - 430 MHz
Page 1 of 7
Replaces Price List dated January 27, 2009
UHF
NXR-8000 Series
400 - 512 MHz
Step 2: Select the "Very Narrow" banding option, if required.
Step 7: Add the basic configuration (Step 1) to the desired RF amplifier, power supply, mounting configuration, and optional
equipment (Steps 2-6) to determine configuration pricing. Specify frequencies, channel bandwidth, tone assignments, and
any special instructions with equipment order.
LIST
STAND-ALONE REPEATERS ONLY
NXR-800K REPEATER, 450 - 480 MHz
$5,333
NXR-800K2 REPEATER, 480 - 512 MHz
$5,333
$5,333
STEP 1 -- NXR-8000 BASIC CONFIGURATION:
NXR8000SK1 BASIC CONFIGURATION, 450 - 480 MHz
$5,860
$5,860
$5,860
NXR8000 repeater / base station basic configuration includes NXR-800 continuous duty 5W repeater and 2 RU, 19-inch rack mountable 20A
13.8VDC power supply. Each system includes factory tuning and staging, one service manual and programming software; ships unmounted.
$25
OPTION KSGCB60004: NXR-SERIES PROGRAMMING CABLE
DB9-F to DB9-F Null / Crossover Cable for programming the NXR-series repeater; 4' length.
STEP 2 -- BANDWIDTH OPTION:
$3,333
OPTION KXK3M: 6.25KHz "VERY NARROW BAND" OPTION
Internally mounted, high-stability OCXO reference oscillator necessary for 6.25KHz operation. NOTE: Only one KXK-3M required per site for 6.25KHz
operation.
$1,561
$1,683
Page 2 of 7
UHF
NXR-8000 Series
400 - 512 MHz
LIST
$2,107
$2,480
$4,924
$5,799
-$50
Delete power supply from basic station configuration or amplifier upgrade configuration. NOTE: Only applies if no power supply is needed at
all. Does not apply for upgrade options, since upgrade pricing reflects automatic removal of basic power supply.
$881
$881
$1,263
$381
$1,157
$1,250
Page 3 of 7
UHF
NXR-8000 Series
400 - 512 MHz
LIST
$1,750
Pricing includes equipment installation, hardware, cabling and wire management materials, and shipping crate.
$2,659
$63
$445
Cabinet upgrade to solid top panel with two low profile, interior-mounted 120VAC fans; replaces standard perforated top panel.
$93
Cabinet upgrade to add solid interior bottom panel inside cabinet, with 5 cable access openings (includes 5 each grommets and plugs).
STEP 6 -- TRUNKING CONFIGURATIONS:
GENERAL TRUNKING OPTIONS:
$1,500
OPTION KSGPG91800: REPEATER TRUNKING FEATURE
8his option enables the trunking features of the NXR-700 repeater . One required for each trunking repeater.
OPTION KSGPGKEYSM: SYSTEM MANAGER SOFTWARE AND SECURE USB KEY PACKAGE
$583
Administrator level key and software necessary to program and manage the system/network. NOTE: Only required for trunking systems.
$37.50
OPTION L-1084: NX-300/800 PROGRAMMING FOR TRUNKING SYSTEMS
Programming and optimization for NX-series mobile and portable units when purchased as part of an integrated trunking system (pricing per unit.)
MULTIPLE SITE , NETWORK TRUNKING OPTIONS:
$11,667
OPTION KSGPG91810: MULTI-SITE NETWORKING FEATURE
This option enables the multiple-site trunking feature of the NXR-800 repeater . One required for each of the first five sites to be networked; sites 6
through 16 are available at no additional charge.
ETHERNET SWITCH & ROUTER OPTIONS FOR TRUNKING CONFIGURATIONS:
NOTE: One switch is required for each site; VPN router(s) may be required for multi-site systems depending on desired
configuration. When needed, VPN router(s) are required in addition to and in conjunction with network switch equipment.
OPTION KSGNS10008: 8-PORT MANAGED NETWORK SWITCH WITH MOUNTING TRAY
$242
OPTION KSGNS10024: RACK MOUNTED 24-PORT MANAGED NETWORK SWITCH
$333
OPTION KSGRT10004: 4-PORT MANAGED VPN ROUTER WITH MOUNTING TRAY
$375
EXTERNAL ANALOG TRUNKING CONTROLLER OPTIONS:
$1,586
Raider LTR dispatch trunking controller. Includes setup, tuning, and interface cable.
Page 4 of 7
UHF
NXR-8000 Series
400 - 512 MHz
LIST
$3,327
Standard features include ESN validation, radio stun/kill, and airtime logging. Contact your systems regional manager for optional selective-call feature.
$3,016
$1,850
$3,242
$683
2 channel tone termination panel, 2 or 4 wire, 600-ohm balanced audio with monitor, occupies 1 RU. NOTE: This option is only available
when used as an analog repeater.
$1,324
16 channel (BCD) tone termination panel, 2 or 4 wire, 600-ohm balanced audio with monitor, occupies 1 RU. NOTE: This option is only
available when used as an analog repeater.
$3,080
$1,693
$323
$961
$8,840
19" rack-mount modular receiver voting comparator. Includes 1 station voter module for primary site (an additional station module is required for
each additional voted receiver site), occupies 3 RU. NOTE: This option is only available when used as an analog repeater.
$1,345
Additional station voter module for signal-to-noise voting comparator. Occupies one card slot in KSGVOT1A chassis. NOTE: This option is only
$855
Internal pilot tone generator for use with voting systems, supplies 600-ohm balanced 2 wire audio, occupies 1 RU. NOTE: This option is only
Page 5 of 7
UHF
NXR-8000 Series
400 - 512 MHz
LIST
$53
OPTION B51-8795-00: NXR-800 SERVICE MANUAL
Additional Service Manual (one manual is already included in the Basic Configuration).
OPTION B51-8827-00: NXR-800 SUPPLEMENT MANUAL
$53
OPTION KPG-109DK: NXR-SERIES REPEATER BASIC PROGRAMMING SOFTWARE
N/A
Additional Programming Software (one copy is already included in the Basic Configuration).
$458
OPTION KPG-110SMK: NXR-SERIES REPEATER TRUNKING SOFTWARE
Additional Programming Software (one copy is already included in the KSGPGKEYSM key/software package). NOTE: This software cannot be
opened without a valid KSGPGKEY01 or KSGPGKEY02 secure USB key.
N/A
OPTION KPG-111DK: NX-SERIES SUBSCRIBER PROGRAMMING SOFTWARE
$167
OPTION KSGPGKEY01: GRADE-1 UNLIMITED ACCESS SECURE USB PROGRAMMING KEY
Additional Grade-1 Secure USB Key (one key is already included in the KSGPGKEYSM key/software package). Provides unlimited access to
system programming & hardware configuration. See Table 1 below for details.
$167
OPTION KSGPGKEY02: GRADE-2 LIMITED ACCESS SECURE USB PROGRAMMING KEY
Provides limited access to system programming & hardware configuration. See Table 1 below for details.
USB KEY FUNCTION OR CAPABILITY
GRADE-1 (BLUE)
PROGRAM GENERAL SYSTEM PARAMETERS
ADD / DELETE / EDIT USERS, TALKGROUPS, CLASSES OF SERVICE, ETC.
ASSIGN OR EDIT REPEATER NETWORK IP ADDRESSES
ADD NEW REPEATER CHANNEL(S)
SWAP OUT SPARE REPEATERS
CONSTRUCT OR ADD NEW SITES
GRADE-2 (YELLOW)
TABLE 1
OPTION KMC-9C: DESKTOP MICROPHONE
$86.00
OPTION KMC-35: STANDARD MOBILE MICROPHONE
$52.50
Note: Pre-selectors, multi-couplers, combiners, outdoor cabinets, and other items are available by special order.
Page 6 of 7
DEALER:
DLR #:
PHONE:
CONTACT:
FAX:
E-MAIL:
SHIP TO:
CITY:
ST:
PREPARED BY:
ZIP:
DATE:
PAGE
OF
TKR/TKB/KSG/NXR
CONFIGURATION
TRANSMIT POWER
-
CONTROL TYPE
W
B
AUDIO LEVELS
2W SIM / 4W DUP
/
P
TRANSMITTER
CHAN
W/N
CHAN 1 RX FREQ
TX CTCSS / DCS
CSQ
CHAN 2 RX FREQ
W/N
TX CTCSS / DCS
CSQ
CHAN 3 RX FREQ
.
RX CTCSS / DCS
CSQ
W/N
RX CTCSS / DCS
CSQ
W/N
RX CTCSS / DCS
CSQ
W/N
RX CTCSS / DCS
CSQ
W/N
RX CTCSS / DCS
CSQ
.
W/N
CHAN 4 TX FREQ
TX CTCSS / DCS
CSQ
CHAN 4 RX FREQ
.
.
CHAN 5 TX FREQ
W/N
TX CTCSS / DCS
CSQ
CHAN 5 RX FREQ
.
5
W/N
.
CHAN 3 TX FREQ
4
CHAN
CSQ
.
3
CHAN
TX CTCSS / DCS
.
CHAN 2 TX FREQ
2
CHAN
W/N
.
1
CHAN
RECEIVER
CHAN 1 TX FREQ
.
CONTROLLER MODEL
CHAN
1
CHAN
2
CHAN
3
CHAN
4
CHAN
5
CONTROLLER
FIRMWARE VERSION
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
KSG CONTROLLER
KSG CONTROLLER
KSG CONTROLLER
KSG CONTROLLER
KSG -
Yes
No
VHF
NXR-7000 Series
136 - 174 MHz
GENERAL:
NXR-7000 VHF Base Stations and Repeaters are integrated systems. The NXR-700 repeater occupies 1 RU and may be used as a
standalone 5W low-power station or in conjunction with an external power amplifier. The NXR-700 can be programmed to operate in
the analog mode at 25 KHz or 12.5 KHz, and in the digital mode at 12.5 KHz or 6.25 KHz.
Mobiles and portables ordered at the same time as an integrated trunking system may be programmed, tested and optimized with the
system prior to shipment. This service will be provided at no charge as a limited time offer. Fees for this service may be applied on
future orders. Programming information is required to properly configure each system. Please contact your Kenwood Systems
Regional Manager for assistance.
OPTIONS:
Station options include external amplifiers with built-in T/R antenna switching for simplex operation, wire line remote control, and power
supply options such as integrated SmartCharger and low voltage disconnect for battery backup applications. High performance 6
cavity BpBr duplexers are also listed, while multi-channel combining systems are quoted on an individual system basis.
Basic NXR7000 repeater configuration includes a 2 RU, 20A, 13.8VDC switching power supply (47-63Hz, 115 or 230VAC); 50W and
110W amplifier options include upgrade to 40A switching power supply (40A model also occupies 2 RU), while a 150W amplifier option
includes an upgrade to a 2 RU, 70A switching power supply. Custom configurations are also available; contact your Kenwood
Required trunking options include enabling of the NXR-700 trunking feature, plus system management software that includes a master
USB key & activation file, which hold a license ID unique to each system. This system manager software permits a system administrator
to change critical features and permissions. Secondary, restricted-level service keys that manage less critical system parameters are
also available.
Each trunking system, including single-site systems, will require an Ethernet switch/router. This router will also serve as the multi-site
network interface when required. NOTE: Recommended models are listed herein, but most commercially available IP equipment is
compatible as well.
K = 146 - 174 MHz
K2 = 136 - 154 MHz
Step 2: Select the "Very Narrow" banding option, if required.
Page 1 of 7
VHF
NXR-7000 Series
136 - 174 MHz
Step 7: Add the basic configuration (Step 1) to the desired RF amplifier, power supply, mounting configuration, and optional
equipment (Steps 2-6) to determine configuration pricing. Specify frequencies, channel bandwidth, tone assignments, and
any special instructions with equipment order.
LIST
STAND-ALONE REPEATERS ONLY
NXR-700K REPEATER, 146 - 174 MHz
$5,333
$5,333
STEP 1 -- NXR-7000 BASIC CONFIGURATION:
$5,860
$5,860
NXR7000 repeater / base station basic configuration includes NXR-700 continuous duty 5W repeater and 2 RU, 19-inch rack mountable 20A
13.8VDC power supply. Each system includes factory tuning and staging, one service manual and programming software; ships unmounted.
$25
OPTION KSGCB60004: NXR-SERIES PROGRAMMING CABLE
DB9-F to DB9-F Null / Crossover Cable for programming the NXR-series repeater; 4' length.
STEP 2 -- BANDWIDTH OPTION:
$3,333
OPTION KXK3M: 6.25KHz "VERY NARROW BAND" OPTION
Internally mounted, high-stability OCXO reference oscillator necessary for 6.25KHz operation. NOTE: Only one KXK-3M required per site for 6.25KHz
operation.
$1,625
$1,975
$2,180
$2,420
Page 2 of 7
VHF
NXR-7000 Series
136 - 174 MHz
LIST
$4,191
$5,065
-$50
Delete power supply from basic station configuration or amplifier upgrade configuration. NOTE: Only applies if no power supply is needed at
all. Does not apply for upgrade options, since upgrade pricing reflects automatic removal of basic power supply.
$881
$881
$1,263
$381
$1,157
$1,250
$1,750
Pricing includes equipment installation, hardware, cabling and wire management materials, and shipping crate.
$2,659
Page 3 of 7
VHF
NXR-7000 Series
136 - 174 MHz
LIST
$63
$445
Cabinet upgrade to solid top panel with two low profile, interior-mounted 120VAC fans; replaces standard perforated top panel.
$93
Cabinet upgrade to add solid interior bottom panel inside cabinet, with 5 cable access openings (includes 5 each grommets and plugs).
STEP 6 -- TRUNKING CONFIGURATIONS:
GENERAL TRUNKING OPTIONS:
$1,500
OPTION KSGPG91800: REPEATER TRUNKING FEATURE
This option enables the trunking features of the NXR-700 repeater . One required for each trunking repeater.
OPTION KSGPGKEYSM: SYSTEM MANAGER SOFTWARE AND SECURE USB KEY PACKAGE
$583
Administrator level key and software necessary to program and manage the system/network. NOTE: Only required for trunking systems.
$37.50
OPTION L-1084: NX-200/700 PROGRAMMING FOR TRUNKING SYSTEMS
Programming and optimization for NX-series mobile and portable units when purchased as part of an integrated trunking system (pricing per unit.)
MULTIPLE SITE , NETWORK TRUNKING OPTIONS:
$11,667
OPTION KSGPG91810: MULTI-SITE NETWORKING FEATURE
This option enables the multiple-site trunking feature of the NXR-700 repeater . One required for each of the first five sites to be networked; sites 6
through 16 are available at no additional charge.
ETHERNET SWITCH & ROUTER OPTIONS FOR TRUNKING CONFIGURATIONS:
NOTE: One switch is required for each site; VPN router(s) may be required for multi-site systems depending on desired
configuration. When needed, VPN router(s) are required in addition to and in conjunction with network switch equipment.
OPTION KSGNS10008: 8-PORT MANAGED NETWORK SWITCH WITH MOUNTING TRAY
$242
OPTION KSGNS10024: RACK MOUNTED 24-PORT MANAGED NETWORK SWITCH
$333
OPTION KSGRT10004: 4-PORT MANAGED VPN ROUTER WITH MOUNTING TRAY
$375
EXTERNAL ANALOG TRUNKING CONTROLLER OPTIONS:
$1,586
Raider LTR dispatch trunking controller. Includes setup, tuning, and interface cable.
$3,016
$1,850
$3,242
Page 4 of 7
VHF
NXR-7000 Series
136 - 174 MHz
LIST
$683
2 channel tone termination panel, 2 or 4 wire, 600-ohm balanced audio with monitor, occupies 1 RU. NOTE: This option is only available
when used as an analog repeater.
$1,324
16 channel (BCD) tone termination panel, 2 or 4 wire, 600-ohm balanced audio with monitor, occupies 1 RU. NOTE: This option is only
$3,080
$323
$961
$8,840
19" rack-mount modular receiver voting comparator. Includes 1 station voter module for primary site (an additional station module is required for
each additional voted receiver site), occupies 3 RU. NOTE: This option is only available when used as an analog repeater.
$1,345
Additional station voter module for signal-to-noise voting comparator. Occupies one card slot in KSGVOT1A chassis. NOTE: This option is only
$855
Internal pilot tone generator for use with voting systems, supplies 600-ohm balanced 2 wire audio, occupies 1 RU. NOTE: This option is only
$53
OPTION B51-8794-00: NXR-700 SERVICE MANUAL
Additional Service Manual (one manual is already included in the Basic Configuration).
OPTION B51-8826-00: NXR-700 SUPPLEMENT MANUAL
$53
OPTION KPG-109DK: NXR-SERIES REPEATER BASIC PROGRAMMING SOFTWARE
N/A
Additional Programming Software (one copy is already included in the Basic Configuration).
$458
OPTION KPG-110SMK: NXR-SERIES REPEATER TRUNKING SOFTWARE
Additional Programming Software (one copy is already included in the KSGPGKEYSM key/software package). NOTE: This software cannot be
opened without a valid KSGPGKEY01 or KSGPGKEY02 secure USB key.
OPTION KPG-111DK: NX-SERIES SUBSCRIBER PROGRAMMING SOFTWARE
Page 5 of 7
N/A
VHF
NXR-7000 Series
136 - 174 MHz
LIST
$167
OPTION KSGPGKEY01: GRADE-1 UNLIMITED ACCESS SECURE USB PROGRAMMING KEY
Additional Grade-1 Secure USB Key (one key is already included in the KSGPGKEYSM key/software package). Provides unlimited access to
system programming & hardware configuration. See Table 1 below for details.
$167
OPTION KSGPGKEY02: GRADE-2 LIMITED ACCESS SECURE USB PROGRAMMING KEY
Provides limited access to system programming & hardware configuration. See Table 1 below for details.
USB KEY FUNCTION OR CAPABILITY
GRADE-1 (BLUE)
PROGRAM GENERAL SYSTEM PARAMETERS
ADD / DELETE / EDIT USERS, TALKGROUPS, CLASSES OF SERVICE, ETC.
ASSIGN OR EDIT REPEATER NETWORK IP ADDRESSES
ADD NEW REPEATER CHANNEL(S)
SWAP OUT SPARE REPEATERS
CONSTRUCT OR ADD NEW SITES
GRADE-2 (YELLOW)
TABLE 1
OPTION KMC-9C: DESKTOP MICROPHONE
$86.00
OPTION KMC-35: STANDARD MOBILE MICROPHONE
$52.50
Note: Pre-selectors, multi-couplers, combiners, outdoor cabinets, and other items are available by special order.
Page 6 of 7
DEALER:
DLR #:
PHONE:
CONTACT:
FAX:
E-MAIL:
SHIP TO:
CITY:
ST:
PREPARED BY:
ZIP:
DATE:
PAGE
OF
TKR/TKB/KSG/NXR
CONFIGURATION
TRANSMIT POWER
-
CONTROL TYPE
W
B
AUDIO LEVELS
2W SIM / 4W DUP
/
P
TRANSMITTER
CHAN
W/N
CHAN 1 RX FREQ
TX CTCSS / DCS
CSQ
CHAN 2 RX FREQ
W/N
TX CTCSS / DCS
CSQ
CHAN 3 RX FREQ
.
RX CTCSS / DCS
CSQ
W/N
RX CTCSS / DCS
CSQ
W/N
RX CTCSS / DCS
CSQ
W/N
RX CTCSS / DCS
CSQ
W/N
RX CTCSS / DCS
CSQ
.
W/N
CHAN 4 TX FREQ
TX CTCSS / DCS
CSQ
CHAN 4 RX FREQ
.
.
CHAN 5 TX FREQ
W/N
TX CTCSS / DCS
CSQ
CHAN 5 RX FREQ
.
5
W/N
.
CHAN 3 TX FREQ
4
CHAN
CSQ
.
3
CHAN
TX CTCSS / DCS
.
CHAN 2 TX FREQ
2
CHAN
W/N
.
1
CHAN
RECEIVER
CHAN 1 TX FREQ
.
CONTROLLER MODEL
CHAN
1
CHAN
2
CHAN
3
CHAN
4
CHAN
5
CONTROLLER
FIRMWARE VERSION
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
KSG CONTROLLER
KSG CONTROLLER
KSG CONTROLLER
KSG CONTROLLER
KSG -
Yes
No
Individual Component Items
LIST
Base Station Amplifiers (Include simplex T-R switching relay)
Low Band
Part Number
Output Power
Input Power
Freq. Range
Compatibility
KSGPA21101
80-100
25-50
30-36
TKB-6900
(specify freq.)
$2,105
KSGPA21102
80-100
25-50
36-42
TKB-6900
(specify freq.)
$2,105
KSGPA21103
80-100
25-50
42-50
TKB-6900
(specify freq.)
$2,105
KSGPA21301
300
25-50
30-36
TKB-6900
(specify freq.)
$5,555
KSGPA21302
300
25-50
36-42
TKB-6900
(specify freq.)
$5,555
KSGPA21303
300
25-50
42-50
TKB-6900
(specify freq.)
$5,555
Part Number
Output Power
Input Power
Freq. Range
KSGPA22421
25-50
2-5
136-144
TKR740/751
(specify freq.)
$1,952
KSGPA22422
25-50
2-5
144-152
TKR740/751
(specify freq.)
$1,952
KSGPA22423
25-50
2-5
150-162
TKR740/751
(specify freq.)
$1,952
KSGPA22424
25-50
2-5
162-174
TKR740/751
(specify freq.)
$1,952
KSGPA22521
25-50
25-50
136-144
TKR750
(specify freq.)
$1,952
KSGPA22522
25-50
25-50
144-152
TKR750
(specify freq.)
$1,952
KSGPA22523
25-50
25-50
150-162
TKR750
(specify freq.)
$1,952
KSGPA22524
25-50
25-50
162-174
TKR750
(specify freq.)
$1,952
KSGPA22400
90-110
2-5
136-144
TKR740/751
(specify freq.)
$2,505
KSGPA22410
90-110
2-5
144-152
TKR740/751
(specify freq.)
$2,505
KSGPA22420
90-110
2-5
150-162
TKR740/751
(specify freq.)
$2,505
KSGPA22430
90-110
2-5
162-174
TKR740/751
(specify freq.)
$2,505
KSGPA22500
90-110
25-50
136-144
TKR750
(specify freq.)
$2,505
KSGPA22510
90-110
25-50
144-152
TKR750
(specify freq.)
$2,505
KSGPA22520
90-110
25-50
150-162
TKR750
(specify freq.)
$2,505
KSGPA22530
90-110
25-50
162-174
TKR750
(specify freq.)
$2,505
KSGPA22451
150
2-5
136-144
TKR740/751
(specify freq.)
$3,988
KSGPA22452
150
2-5
144-152
TKR740/751
(specify freq.)
$3,988
KSGPA22453
150
2-5
150-162
TKR740/751
(specify freq.)
$3,988
KSGPA22454
150
2-5
162-174
TKR740/751
(specify freq.)
$3,988
KSGPA22551
150
25-50
136-144
TKR750
(specify freq.)
$3,988
KSGPA22552
150
25-50
144-152
TKR750
(specify freq.)
$3,988
KSGPA22553
150
25-50
150-162
TKR750
(specify freq.)
$3,988
KSGPA22554
150
162-174
TKR750
(specify freq.)
$3,988
VHF High Band
25-50
Page 1 of 7
Compatibility
LIST
UHF
Part Number
Output Power
Input Power
Freq. Range
KSGPA23421
20-40
2-5
406-426
TKR840/851
(specify freq.)
$1,893
KSGPA23422
20-40
2-5
426-450
TKR840/851
(specify freq.)
$1,893
KSGPA23423
20-40
2-5
450-470
TKR840/851
(specify freq.)
$1,893
KSGPA23424
20-40
2-5
470-490
TKR840/851
(specify freq.)
$1,893
KSGPA23425
20-40
2-5
490-512
TKR840/851
(specify freq.)
$1,893
KSGPA23521
20-40
24-40
406-426
TKR850
(specify freq.)
$1,893
KSGPA23522
20-40
24-40
426-450
TKR850
(specify freq.)
$1,893
KSGPA23523
20-40
24-40
450-470
TKR850
(specify freq.)
$1,893
KSGPA23524
20-40
24-40
470-490
TKR850
(specify freq.)
$1,893
KSGPA23525
20-40
24-40
490-512
TKR850
(specify freq.)
$1,893
KSGPA23400
80-100
2-5
406-426
TKR840/851
(specify freq.)
$2,430
KSGPA23410
80-100
2-5
426-450
TKR840/851
(specify freq.)
$2,430
KSGPA23420
80-100
2-5
450-470
TKR840/851
(specify freq.)
$2,430
KSGPA23430
80-100
2-5
470-490
TKR840/851
(specify freq.)
$2,430
KSGPA23440
80-100
2-5
490-512
TKR840/851
(specify freq.)
$2,430
KSGPA23500
80-100
24-40
406-426
TKR850
(specify freq.)
$2,430
KSGPA23510
80-100
24-40
426-450
TKR850
(specify freq.)
$2,430
KSGPA23520
80-100
24-40
450-470
TKR850
(specify freq.)
$2,430
KSGPA23530
80-100
24-40
470-490
TKR850
(specify freq.)
$2,430
KSGPA23540
80-100
24-40
490-512
TKR850
(specify freq.)
$2,430
KSGPA23451
150
2-5
406-426
TKR840/851
(specify freq.)
$4,722
KSGPA23452
150
2-5
426-450
TKR840/851
(specify freq.)
$4,722
KSGPA23453
150
2-5
450-470
TKR840/851
(specify freq.)
$4,722
KSGPA23454
150
2-5
470-490
TKR840/851
(specify freq.)
$4,722
KSGPA23455
150
2-5
490-512
TKR840/851
(specify freq.)
$4,722
KSGPA23551
150
24-40
406-426
TKR850
(specify freq.)
$4,722
KSGPA23552
150
24-40
426-450
TKR850
(specify freq.)
$4,722
KSGPA23553
150
24-40
450-470
TKR850
(specify freq.)
$4,722
KSGPA23554
150
24-40
470-490
TKR850
(specify freq.)
$4,722
KSGPA23555
150
24-40
490-512
TKR850
(specify freq.)
$4,722
Page 2 of 7
Compatibility
LIST
Repeater Station Amplifiers
VHF High Band
Part Number
Output Power
Input Power
Freq. Range
KSGPA22401
25-50
2-5
136-144
Compatibility
TKR740/751
(specify freq.)
$1,447
KSGPA22402
25-50
2-5
144-152
TKR740/751
(specify freq.)
$1,447
KSGPA22403
25-50
2-5
150-162
TKR740/751
(specify freq.)
$1,447
KSGPA22404
25-50
2-5
162-174
TKR740/751
(specify freq.)
$1,447
KSGPA22501
25-50
25-50
136-144
TKR750
(specify freq.)
$1,447
KSGPA22502
25-50
25-50
144-152
TKR750
(specify freq.)
$1,447
KSGPA22503
25-50
25-50
150-162
TKR750
(specify freq.)
$1,447
KSGPA22504
25-50
25-50
162-174
TKR750
(specify freq.)
$1,447
KSGPA22411
55-110
2-5
136-144
TKR740/751
(specify freq.)
$1,999
KSGPA22412
55-110
2-5
144-152
TKR740/751
(specify freq.)
$1,999
KSGPA22413
55-110
2-5
150-162
TKR740/751
(specify freq.)
$1,999
KSGPA22414
55-110
2-5
162-174
TKR740/751
(specify freq.)
$1,999
KSGPA22511
55-110
25-50
136-144
TKR750
(specify freq.)
$1,999
KSGPA22512
55-110
25-50
144-152
TKR750
(specify freq.)
$1,999
KSGPA22513
55-110
25-50
150-162
TKR750
(specify freq.)
$1,999
KSGPA22514
55-110
25-50
162-174
TKR750
(specify freq.)
$1,999
KSGPA22441
150
2-5
136-144
TKR740/751
(specify freq.)
$3,146
KSGPA22442
150
2-5
144-152
TKR740/751
(specify freq.)
$3,146
KSGPA22443
150
2-5
150-162
TKR740/751
(specify freq.)
$3,146
KSGPA22444
150
2-5
162-174
TKR740/751
(specify freq.)
$3,146
KSGPA22541
150
25-50
136-144
TKR750
(specify freq.)
$3,146
KSGPA22542
150
25-50
144-152
TKR750
(specify freq.)
$3,146
KSGPA22543
150
25-50
150-162
TKR750
(specify freq.)
$3,146
KSGPA22544
150
25-50
162-174
TKR750
(specify freq.)
$3,146
Part Number
Output Power
Input Power
Freq. Range
KSGPA23401
20-40
2-5
406-426
TKR840/851
(specify freq.)
$1,389
KSGPA23402
20-40
2-5
426-450
TKR840/851
(specify freq.)
$1,389
KSGPA23403
20-40
2-5
450-470
TKR840/851
(specify freq.)
$1,389
KSGPA23404
20-40
2-5
470-490
TKR840/851
(specify freq.)
$1,389
KSGPA23405
20-40
2-5
490-512
TKR840/851
(specify freq.)
$1,389
KSGPA23501
20-40
24-40
406-426
TKR850
(specify freq.)
$1,389
UHF
Page 3 of 7
Compatibility
LIST
KSGPA23502
20-40
24-40
426-450
TKR850
(specify freq.)
$1,389
KSGPA23503
20-40
24-40
450-470
TKR850
(specify freq.)
$1,389
KSGPA23504
20-40
24-40
470-490
TKR850
(specify freq.)
$1,389
KSGPA23505
20-40
24-40
490-512
TKR850
(specify freq.)
$1,389
KSGPA23411
80-100
2-5
406-426
TKR840/851
(specify freq.)
$1,926
KSGPA23412
80-100
2-5
426-450
TKR840/851
(specify freq.)
$1,926
KSGPA23413
80-100
2-5
450-470
TKR840/851
(specify freq.)
$1,926
KSGPA23414
80-100
2-5
470-490
TKR840/851
(specify freq.)
$1,926
KSGPA23415
80-100
2-5
490-512
TKR840/851
(specify freq.)
$1,926
KSGPA23511
80-100
24-40
406-426
TKR850
(specify freq.)
$1,926
KSGPA23512
80-100
24-40
426-450
TKR850
(specify freq.)
$1,926
KSGPA23513
80-100
24-40
450-470
TKR850
(specify freq.)
$1,926
KSGPA23514
80-100
24-40
470-490
TKR850
(specify freq.)
$1,926
KSGPA23515
80-100
24-40
490-512
TKR850
(specify freq.)
$1,926
KSGPA23441
150
2-5
406-426
TKR840/851
(specify freq.)
$3,880
KSGPA23442
150
2-5
426-450
TKR840/851
(specify freq.)
$3,880
KSGPA23443
150
2-5
450-470
TKR840/851
(specify freq.)
$3,880
KSGPA23444
150
2-5
470-490
TKR840/851
(specify freq.)
$3,880
KSGPA23445
150
2-5
490-512
TKR840/851
(specify freq.)
$3,880
KSGPA23541
150
24-40
406-426
TKR850
(specify freq.)
$3,880
KSGPA23542
150
24-40
426-450
TKR850
(specify freq.)
$3,880
KSGPA23543
150
24-40
450-470
TKR850
(specify freq.)
$3,880
KSGPA23544
150
24-40
470-490
TKR850
(specify freq.)
$3,880
KSGPA23545
150
24-40
490-512
TKR850
(specify freq.)
$3,880
Part Number
Output Power
Freq. Range
KSGPA24141
40
851-869
TKR900
$2,465
KSGPA24181
80
851-869
TKR900
$2,901
KSGPA24131
130
851-869
TKR900
$4,487
Part Number
Output Power
Freq. Range
KSGPA25142
40
935-940
TKR901
$2,465
KSGPA25172
75
935-940
TKR901
$2,901
KSGPA25132
130
935-940
TKR901
$4,487
800 MHz
Compatibility
900 MHz
Compatibility
Page 4 of 7
LIST
Mounting Equipment
Part Number
KSGMT30001
2 RU, 5" High, 20.5" Wide, 16" Deep Desktop Enclosure (Unassembled)
$242
KSGMT30004
4 RU, 8.5" High, 20.5" Wide, 16" Deep Desktop Enclosure (Unassembled)
$260
KSGMT13000
17 RU, 3' High, 19" Wide Equipment Rack (Unassembled)
$755
KSGMT17000
45 RU, 7' High, 19" Wide Equipment Rack (Unassembled)
$633
KSGMT90001
Rack Standoffs (Kit of 20, includes hardware)
KSGMT20020
20 RU, 42" Locking Cabinet with Standard Perforated Top Lid
$1,985
KSGMT20040
40 RU, 77" Locking Cabinet with Standard Perforated Top Lid
$2,367
KSGMT20001
Cabinet Solid Top
KSGMT20002
Cabinet Fan Top Assembly
KSGMT20003
Cabinet Solid Floor
$76
$63
$445
$93
Power Supplies
Part Number
Description
KSGPS20200
20A, 13.8VDC internally mounted power supply for 750/751/850/851
$247
KSGPS20201
20A, 13.8VDC 19" wide rack mounted power supply for all other models
$375
KSGPS20400
40A, 13.8VDC 19" wide rack mounted power supply
$473
KSGPS20352
35A, 13.8VDC 19" wide rack mounted power supply with Smartcharger
$1,355
KSGPS20701
70A, 13.8VDC 19" wide rack mounted power supply
$1,355
KSGPS20702
70A, 13.8VDC 19" wide rack mounted power supply with Smartcharger
$1,736
Remote Control Termination Panels
Part Number
Description
KSGTN01C
1 Channel Tone Termination Panel with Case
$607
KSGTN02C
2 Channel Tone Termination Panel with Case
$683
KSGTN02N
2 N-Channel Tone Termination Panel with Case
$683
KSGTN10C
10 Channel Discrete Tone Termination Panel with Case
$1,253
KSGTM20016
16 Channel BCD Tone Termination Panel with Case
$1,324
KSGTDC2C
2 Channel DC Termination Panel with Case
$354
KSGTALDC
1 Channel 600 Ohm Balanced Audio Line Driver & 4-Wire E&M Interface with Case
$326
KSGUT10001
19" Rack Mounted 1RU Termination Panel Mounting Tray
Page 5 of 7
$41
LIST
External Controllers
Part Number
Description
KSGCT11040
Raider LTR Dispatch Trunking Controller
$1,539
KSGCT11041
Raider Xtreme Single-Site Trunking Controller (UHF Only)
$3,280
KSGCT11050
Marauder LTR Dispatch and Interconnect Trunking Controller
$2,977
KSGCT20038
Model 38 Conventional Repeater Controller
$1,197
KSGCT20452
Model 452 LTR Dispatch Trunking Controller
$1,832
KSGCT20459
Model 459 LTR Dispatch and Interconnect Trunking Controller
$3,217
KSGCT20807
Model 807 Basic MPT-1327 Trunking Controller
$4,501
KSGCT20827
Model 827 Basic MPT-1327 Interconnect Controller
$6,167
KSGCT20844
Model 844 Basic MPT-1327 Multi-Site Controller
$9,667
KSGCT20427
Model 427 Basic MPT-1327 Peripheral Equipment Interface
$9,667
Duplexers
Part Number
Description
KSGDX12556
VHF High Band 6-Cavity BpBr Duplexer, 350W, 400 KHz Minimum Spacing
$3,055
KSGDX13546
UHF 6-Cavity BpBr Duplexer, 250W, 3 MHz Minimum Spacing
$3,055
KSGDX23101
UHF 4-Cavity BpBr Duplexer, 350W, 5 MHz Minimum Spacing (450-470 MHz Only)
$1,631
KSGDX14644
800MHz 4-Cavity BpBr Duplexer, 250W, 45 MHz Minimum Spacing
$2,609
KSGDX15644
900MHz 4-Cavity BpBr Duplexer, 250W, 39 MHz Minimum Spacing
$2,609
Modems
Part Number
Description
KSGMD10001
Basic Site Management Modem
$250
KSGMD20000
High Performance Site Management Modem
$888
Repeaters
Part Number
Description
TKR740KS
VHF High-Performance Repeater
Freq. Range
146-162
$3,350
TKR740K2S
158-174
$3,350
TKR740K3S
136-150
$3,350
Page 6 of 7
LIST
TKR750KS
VHF Repeater (15-50 watts output)
146-162
$1,575
TKR750K2S
136-146
$1,575
TKR751KS
146-174
$1,400
TKR840KS
UHF High-Performance Repeater
450-480
$3,455
TKR840K2S
UHF High-Performance Repeater
480-512
$3,455
TKR850KS
UHF Repeater (15-40 watts output)
450-480
$1,680
TKR850K2S
480-512
$1,680
TKR850K3S
400-430
$1,680
TKR851KS
450-480
$1,505
TKR851K2S
480-512
$1,505
TKR900KS
800MHz Transceiver
806-821/851-866
$3,255
NOTE: Pricing for All Repeaters Shown above include Factory Tuning
Other
Part Number
Description
KSGVOT1A
Signal-To-Noise Voter, Modular Design (includes One Station Voter Module)
$8,840
KSGVOT2A
Additional Station Voter Module
$1,345
KSGTM30010
Voting Pilot Tone Generator and Line Driver
$858
KSGMS10040
Antenna-Relay Assy for TKR-740/840, Retrofit, 5W
$340
KSGMS10050
Antenna-Relay Assy for TKR-750/751/850/851, Retrofit, 50W
$340
KSGMS00101
19", 1 RU Blank Face Panel
$15
KSGMS00102
$26
KSGMS00103
$38
KSGMS100P1
19", 12-Outlet 15 Amp AC Power Strip, 1 RU
$91
Page 7 of 7
800 MHz
TKR-9300 Series Repeaters
GENERAL:
The TKR-900 transceiver occupies 2 RU, has an RF output level of 250mW and is intended to be used as a driver for an external
power amplifier. An external conventional or trunking controller is required to establish repeater operation. Internal high stability TCXOs
and OCXOs eliminate the need for external reference oscillators.
OPTIONS:
Conventional station options include external controllers, wire line remote control and external RF amplifiers. Trunking system options
include external LTR controllers; PassPort systems are available by individual quotation. High performance 4-cavity BpBr duplexers
are listed as options; multichannel combining systems are quoted on an individual system basis. Power supply options include battery
backup with integrated SmartCharger and Low Voltage Disconnect for the 40W and 80W configurations.
The basic TKR-900 transceiver is supplied as a component only (no power supply); amplifier upgrades include a 40A switching power
supply occupying 2 RU. Custom configurations are also available; contact your Kenwood Systems Regional Sales Manager for more
details.
800 MHz SMR channels = 806-821 / 851-866 MHz
Order TKR900KS basic transceiver
Step 5: Select optional equipment or configuration changes. (Note: External Controller is required for equipment operation.)
equipment (Steps 2-5) to determine configuration pricing. Specify frequencies (or FCC channel numbers) and tone
assignments with order.
Page 1 of 5
800 MHz
LIST
$3,255
TKR900KS 800 MHz BASIC TRANSCEIVER 806-821 / 851-866 MHz
800MHz, 250mW continuous duty full-duplex transceiver; no internal repeat functionality. Occupies 2RU, ships unmounted.
$53
$2,987
OPTION KSGA404A: 40W CONTINUOUS DUTY 800MHz RF AMPLIFIER UPGRADE
Basic TKR900 transceiver upgrade to include external 40W continuous duty 800MHz RF amplifier. Amplifier occupies 4 RU and includes a 40A,
13.8VDC power supply. Includes factory tuning, wiring and RF cables.
$3,425
$4,992
$881
For amplifier options above, upgrade to 35A, 13.8VDC continuous duty switching power supply with front panel metering, built-in SmartCharger,
low-voltage disconnect, and solid state no-break transfer diodes. Occupies 2 RU, includes sealed fuse holder and fuses for battery (battery not
included). Gel cell batteries are available separately; please contact your Kenwood Systems Regional Sales Manager for details.
$881
For amplifier options above, upgrade to 70A, 13.8VDC continuous duty switching power supply with front panel metering; occupies 2 RU. Will
$1,263
For amplifier options above, upgrade to 70A, 13.8VDC continuous duty switching power supply with front panel metering, built-in SmartCharger,
low-voltage disconnect, and solid state no-break transfer diodes. Occupies 2 RU, includes sealed fuse holder and fuses for battery (battery not
included). Will power up to 2 channels. Gel cell batteries are available separately; please contact your Kenwood Systems Regional Sales Manager for
details.
$1,157
$1,250
$1,750
Page 2 of 5
800 MHz
LIST
$2,659
$63
$445
$93
$675
$683
$393
$367
EXTERNAL CONTROLLER OPTIONS:
OPTION KSGC038L: CONVENTIONAL REPEATER CONTROLLER
$1,237
Model 38 conventional repeater controller. Includes setup, tuning, and interface cable.
$1,586
$3,016
$1,850
$3,242
Page 3 of 5
800 MHz
LIST
$2,583
OPTION KSGD4P1A: 4 CAVITY 800MHz BpBr DUPLEXER
4 cavity Bandpass/Bandreject duplexer, 250W continuous duty, minimum TX-RX spacing 45 MHz. Includes RF cables, mounting, and factory tuning.
$323
$961
$8,840
``
$1,345
$855
Internal pilot tone generator for use with voting systems, supplies 600Ohm balanced two wire audio, installs in one station option bay.
Page 4 of 5
DEALER:
DLR #:
PHONE:
CONTACT:
FAX:
E-MAIL:
SHIP TO:
CITY:
ST:
PREPARED BY:
ZIP:
DATE:
PAGE
OF
TKR/TKB/KSG/NXR
CONFIGURATION
TRANSMIT POWER
-
CONTROL TYPE
W
B
AUDIO LEVELS
2W SIM / 4W DUP
/
P
TRANSMITTER
CHAN
W/N
CHAN 1 RX FREQ
TX CTCSS / DCS
CSQ
CHAN 2 RX FREQ
W/N
TX CTCSS / DCS
CSQ
CHAN 3 RX FREQ
.
RX CTCSS / DCS
CSQ
W/N
RX CTCSS / DCS
CSQ
W/N
RX CTCSS / DCS
CSQ
W/N
RX CTCSS / DCS
CSQ
W/N
RX CTCSS / DCS
CSQ
.
W/N
CHAN 4 TX FREQ
TX CTCSS / DCS
CSQ
CHAN 4 RX FREQ
.
.
CHAN 5 TX FREQ
W/N
TX CTCSS / DCS
CSQ
CHAN 5 RX FREQ
.
5
W/N
.
CHAN 3 TX FREQ
4
CHAN
CSQ
.
3
CHAN
TX CTCSS / DCS
.
CHAN 2 TX FREQ
2
CHAN
W/N
.
1
CHAN
RECEIVER
CHAN 1 TX FREQ
.
CONTROLLER MODEL
CHAN
1
CHAN
2
CHAN
3
CHAN
4
CHAN
5
CONTROLLER
FIRMWARE VERSION
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
SYNC MASTER
LTR CHAN
AREA
INTERCONNECT
RDD
CWID
NONE
FIRMWARE
CURRENT
KSG CONTROLLER
KSG CONTROLLER
KSG CONTROLLER
KSG CONTROLLER
KSG -
Yes
No

Price Pages

Transcription

Similar documents

th-g71a fm dual bander

Mac User Mar 2001

TK-90

our product brochure

TTMAV-700C Tower Mounted Amplifier Twin Variable Gain

PRO7350

RFS Brochure_5044 Series_New Address_06-12-13.fm

Kenwood TS-520S - WB4HFN Home Page

Receptor radio pentru acces autovehicule Rosslare AY-L23C