RDI-C 2x2 Series

Transcription

RDI-C 2x2 Series

RDI-C 2x2 Series
Center Basket
Recessed Direct-Indirect Unit
Application:
This
attractive
2’x2’
Direct/Indirect Center Basket Troffer Unit
combines
the
energy
efficient
performances of electronic ballast with
soft low-glare contemporary design. The
RDI-C unit is designed for use with Biax,
T5, and T8 lamps to provide uniform
balanced
illumination
,
consistent
distribution and high end appearance.
Designed for use in most offices and retail
establishments this unit is as efficient as it
is attractive
Construction: Housing is die formed
from heavy gauge steel and is finished in a
matte white polyester powder coating for
maximum reflectivity and durability.
Perforated center basket incorporates
hinges from both sides to allow for easy
lamp replacement.
Electrical: All units are furnished with UL
Listed Class P thermally protected ballast.
Other voltages are available upon request.
Fixtures meet requirements for UL
Luminaire Standard # 1598. All units
comply with National Energy Standards.
Mounting: Designed for use in inverted T
Bar ceilings, this fixture comes with
integral earthquake clips built into end
plate. All units are equipped access plates
for easy wiring as well as 7/8” knockouts
in top, sides and end of all units.
Ordering Information
Maximum Weight = 20 lbs.
Specifications Subject To Change Without Notice
Model
Size
# Lamps
Lamp Type
Voltage
RDI-C
2X2
2
17
MV
Options
T5 Lamps
RDI-C
Recessed
Direct/Indirect
Center Basket
2x2
1 = One
2 = Two
3 = Three
14= F14T5
24 = F24T5HO
T8 Lamps
Page 2
40BX = 40w Biax
50BX = 50w Biax
55BX = 55w Biax
Blank = 120V
277= 277 volt
MV = Multi
Volt
EMER = Emergency Ballast
17 = F17T8
K-B Lighting Mfg. Co., Inc.
(215) 953-6663 phone
Biax / Twin Tube
2515 Metropolitan Drive / Trevose, PA 19053
(215) 953-6710 fax
[email protected] email
RDI-C 2x4 Series
Center Basket
Application: This attractive 2’x4’
combines the energy efficient
balanced illumination, consistent
is attractive.
lamp replacement.
for easy wiring as well as 7/8” knockouts in
top, sides and end of all units.
Model
Size
# Lamps
Lamp Type
Voltage
RDI-C
2X4
2
32
MV
Options
T5 Lamps
RDI-C
Recessed
Direct/Indirect
Center Basket
2x4
1 = One
2 = Two
3 = Three
28 = F28T5
54 = F54T5HO
T8 Lamps
Page 2
Blank = 120V
277= 277 volt
MV = Multi Volt
32 = F32T8
(215) 953-6663 phone
LED
48LED =20w LED
(215) 953-6710 fax
HB Series
High Bay 4 or 6 Tube
Application: This cost effective HB Series is
ideal for use in commercial and industrial areas
where high bay installation is required. The HB
Series is an energy efficient direct replacement
for Metal Halide High Bay Units.
Construction: This high efficiency industrial unit
is designed from heavy gauge die formed
aluminum for reduced weight and maximum heat
dissipation. Heat removal vents are included to
reduce heat buildup in electrical raceway. End
Plates are designed from heavy gauge die
formed steel for strength durability. Units are
finished in a white polyester powder coating for
maximum reflectivity. Reflector is designed from
multifaceted 95% specular reflective aluminum
designed to maximize efficiency and increase
performance.
Electrical: All units are furnished with universal
voltage, UL Listed, Class P, thermally protected
ballast. Light level switching systems are
available. Fixtures meet all requirements for UL
Luminaire Standard # 1598. All units comply with
National Energy Standards.
Mounting: Unit is equipped with slots for chain or
cable hanging and knockouts for pendant
mounting. Unit can be mounted individually of in
continuous run. 7/8" knockouts are provided in
back and end plates for conduit connector.
Coefficients Utilization Zonal Cavity Method
RF
20
RC
80%
70%
50%
RW 70
50 30 70 50 30 50 30
94 94 93
1 105 102 99 96 95
80 82 80
2 96 89 81 93 86
90
81
56
87
80
74 78 72
3
66 70 64
4 82 73 47 80 74
58 63 56
5 76 65 40 74 64
51 57 50
6 70 58 35 68 57
44 51 45
7 64 53 30 64 53
40 46 39
8 60 48 26 58 46
35 41 34
9 55 42 23 53 42
32 38 31
10 51 39 21 50 39
T8
F32T8
Model
# Lamps
Lamp Type
Ballast
HB
6
54T5HO
E
28T5 = F28T5
54T5HO = F54T5HO
32 = F32T8
E = Electronic
4 = Four
6 = Six
MH
Metal Halide
T5HO
Fluorescent
T8
Fluorescent
Fixture Length
T5
T5HO
F28T5
F54T5HO
4 Lamp High Bay Length 48”
Maximum Weight = 30 lbs. / 48”
HB
Length
48”
Bulb
250
400
4-Lite
6-Lite
4-Lite
6-Lite
Lumens
13,500
24,500
19,000
28,500
9,900
14,800
Voltage
6 Lamp High Bay Length 48”
Options
Lens
A12C
Blank = 120/277
EMER= Emergency Ballast
WG = Wire Guard
Door = Metal Door Frame
Fixture Efficiency
68%
95%
(215) 953-6663 phone
Length
46”
Actual Lumens
9,180
16,600
18,050
27,075
9,400
14,000
A12C = Prismatic Acrylic Lens
Poly = Polycarbonate
AC = Clear Smooth Acrylic
Wattage
300
460
240
360
112
170
(215) 953-6710 fax
Page 3
EC5 Series
Economy Channel One Tube
Application: This cost effective strip light
is ideal for use in all residential, commercial
and industrial areas where general lighting
is desired.
Construction: This unit is designed from
heavy gauge die formed steel and is
finished in baked white enamel or polyester
powder coating for maximum durability and
reflectivity. End plate doubles as coupler
when fixture is used in continuous run.
Symmetric and asymmetric reflectors are
available.
Luminaire Standard # 1598.
All units
Mounting: Unit is equipped with knockouts
and holes for pendant or surface mounting.
This fixture can be mounted individually or
in continuous run. 7/8” knock out is
provided in end plate for conduit connector.
20
80%
70%
50%
RW 70
50 30 10 70 50 30 10 50 30 10
0 105 105 105 105 99 99 99 99 89 89 89
1 92 87 82 77 87 82 78 74 74 70 67
2 83 74 66 60 78 70 63 58 62 57 53
3 75 64 56 49 70 61 53 47 54 48 43
4 68 56 47 41 64 53 45 39 48 41 36
5 62 49 40 33 58 46 38 32 42 35 30
6 56 43 35 28 53 41 33 27 37 30 25
7 52 39 30 24 49 37 29 23 33 26 21
8 48 35 26 21 45 33 25 20 30 23 18
9 44 31 23 18 41 30 22 17 27 20 16
10 41 28 21 16 39 27 20 15 24 18 14
Fixture Length
RF
RC
T8
Length
F17T8 24”
F25T8 36”
F32T8 48”
Model
# Lamps
Lamp Type
Ballast
EC5-
1
32
E
1 = One
EC5
Tandem
21 = Single Row
T5 Lamps
14T5 = F14T5
21T5 = F21T5
28T5 = F28T5
35T5 = F35T5
T5 High Output
24T5HO = F24T5HO
39T5HO = F39T5HO
54T5HO = F54T5HO
80T5HO = F80T5HO
T8 Lamps
17 = F17T8
25 = F25T8
32 = F32T8
40T8 = F40T8
(215) 953-6663 phone
T5
T5HO
F24T5HO
F21T5
F39T5HO
F28T5
F54T5HO
Length
22”
34”
46”
F40T8
60” F35T5
F80T5HO
58”
48LED
48”
Voltage
Blank = 120V
E = Electronic
277 = 277 V
Blank = No Ballast
MV= Multi Volt
LED
24LED = 24” LED
48LED = 48” LED
F14T5
Options
O = Grounded Outlet
TOG = Toggle Switch
ROC = Rocker Switch
PULL = Pull Switch
SYM = Symmetrical Reflector
ASY = Asymmetrical Reflector
REF = Specular Reflector
Cord
CP-XE = Exit End
CP-XS = Exit Side
CP-XB = Exit Base
Specify Cord Length
(215) 953-6710 fax
Page 4
EC1 Series
Economy Channel One Tube
Application: This cost effective strip light is
ideal for use in all residential, commercial and
industrial areas where general lighting is
desired.
heavy gauge die formed steel and is finished
in baked white enamel or polyester powder
coating for maximum durability and reflectivity.
Socket bar, end plate, and ballast cover snapon allowing for tool–free assembly. End plate
doubles as coupler when fixture is used in
continuous run. Symmetric and asymmetric
reflectors are available.
Fixtures meet requirements for UL Luminaire
Standard # 1598.
All units comply with
This fixture can be mounted individually or in
continuous run. 7/8” knock out is provided in
end plate for conduit connector.
Fixture Length
RF
RC
RW
0
1
2
3
4
5
6
7
8
9
10
20
80%
70%
50%
70 50 30 10 70 50 30 10
50 30
105 105 105 105 99 99 99 99
89
89
92 87 82 77 87 82 78 74
74
70
83 74 66 60 78 70 63 58
62
57
75 64 56 49 70 61 53 47
54
48
68 56 47 41 64 53 45 39
48
41
62 49 40 33 58 46 38 32
42
35
56 43 35 28 53 41 33 27
37
30
52 39 30 24 49 37 29 23
33
26
48 35 26 21 45 33 25 20
30
23
44 31 23 18 41 30 22 17
27
20
41 28 21 16 39 27 20 15
24
18
10
89
67
53
43
36
30
25
21
18
16
14
# Lamps
EC1-
1
1 = One
2 = Two *
EC1
Single Row
Tandem
21 = 2 Tube
31 = 3 Tube
41 = 4 Tube
* Two Lamp
Wide
T8 or T5 Only
T8
----F17T8
F25T8
F32T8
F40T8
T5
----F14T5
F21T5
F28T5
F35T5
--
48LED
--
T5 HO
BIAX Length
----15”
----18”
F24T5HO F40BX
24”
F39T5HO
--36”
F54T5HO
--48”
F80T5HO
--60”
--
--
48”
For Tandem Units:
Multiply lamp length above by lamp quantity
Model
T12
F14T12
F15T12
F20T12
F30T12
F40T12
---
Lamp Type
Ballast
32
E
T12 Lamps
14 = F14T12
15 = F15T12
20 = F20T12
30 = F30T12
40 = F40T12
T8 Lamps
17 = F17T8
25 = F25T8
32 = F32T8
40 = F40T8
LED
48LED = 48” LED
T5 lamps
14T5 = F14T5
21T5 = F21T5
28T5 = F28T5
35T5 = F35T5
T5 High Output
24T5 = F24T5HO
39T5 = F39T5HO
54T5 = F54T5HO
80T5 = F80T5HO
Biax Lamps
40BX = F40BX
M = Magnetic
E = Electronic .88 BF
E-LW =Electronic .77 BF
E-OD = Electronic 1.18 BF
(215) 953-6663 phone
Voltage
Options
Blank = 120V
277 = 277 V
MV= Multi Volt
O = Grounded Outlet
TOG = Toggle Switch
ROC = Rocker Switch
PULL = Pull Switch
WG = Wire Ground
EMB = Emergency Ballast
ASY =Asymmetrical Reflector
(215) 953-6710 fax
Page 5
Cord
CP-XE=Exit End
CP-XS=Exit Side
CP-XB=Exit Base
Specify Cord
Length
EC2 Series
Economy Channel Two Tube
Application: This cost effective strip light is
ideal for use in all residential, commercial and
industrial areas where general lighting is
desired.
Construction: This unit is designed from heavy
gauge die formed steel and is finished in baked
white enamel or polyester powder coating for
maximum durability and reflectivity. Socket bar,
end plate, and ballast cover snap-on allowing for
tool–free assembly. End plate doubles as
coupler when fixture is used in continuous run.
Symmetric and asymmetric reflectors are
available.
Electrical: All units are furnished with UL Listed
Class P thermally protected ballast. Other
voltages are available upon request. Fixtures
meet requirements for UL Luminaire Standard #
1598. All units comply with National Energy
Standards.
.
Mounting: Unit is equipped with knockouts and
holes for pendant or surface mounting. This
fixture can be mounted individually or in
continuous run. 7/8” knock out is provided in end
plate for conduit connector.
Fixture Length
RF 20
RC
80%
70%
50%
RW 70
50 30 10 70 50 30 10 50 30 10
102 102 102 102 98 98 98 98 89 89 89
0
91 86 82 78 87 83 79 75 76 72 70
1
82 74 67 62 78 71 65 60 65 60 56
2
75 65 57 52 71 62 55 49 57 51 46
3
68 57 48 42 64 54 47 41 50 44 39
4
62 50 41 35 58 48 40 34 44 37 32
5
56 44 36 30 54 42 35 29 39 32 27
6
52 39 31 26 49 38 30 25 35 28 24
7
48 35 27 22 45 34 26 21 31 25 20
8
44 32 24 19 42 30 22 18 28 22 17
9
10 41 29 21 16 39 28 21 16 25 19 15
Photometric Curve
T12
T12HO
T8
T5HO
Length
F14T12
---
---
---
---
---
15”
F15T12
---
---
---
---
---
18”
F20T12
---
F17T8
---
F14T5
F24T5H0
24”
F30T12
---
F25T8
---
F21T5
F39T5H0
36”
F32T8
---
F28T5
F54T5HO
48”
F40T8
---
F35T5
F80T5H0
60”
---
---
---
---
72”
F96T8HO
---
---
96”
F40T12 F48T12HO
---
---
F72T12 F72T12HO
F96T12 F96T12HO F96T8
T8HO
T5
For Tandem Units: Multiply lamp length above by lamp quantity
Model
# Lamps
EC2-
2
1 = One
2 = Two
EC2
Tandem
21 = Single
22 = Double
13 lbs. / 96”
Lamp Type
Ballast
32
E
T5 lamps
14T5 = F14T5
21T5 = F21T5
28T5 = F28T5
35T5 = F35T5
T5HO Lamps
24T5HO = F24T5HO
39T5HO = F39T5HO
54T5HO = F54T5HO
80T5HO = F80T5HO
T8 Lamps
17 = F17T8
25 = F25T8
32 = F32T8
40T8 = F40T8
96T8 = F96T8
T12 Lamps
14 = F14T12
15 = F15T12
20 = F20T12
30 = F30T12
40 = F40T12
72 = F72T12
96 = F96T12
T12 High Output
24HO = F24HO
48HO = F48HO
72HO = F72HO
96HO = F96HO
Voltage
Options
O = Grounded Outlet
TOG = Toggle Switch
ROC = Rocker Switch
CP-XE=Exit End
M = Magnetic
Blank = 120V PULL = Pull Switch
CP-XS=Exit Side
277 = 277 V
WG = Wire Ground
CP-XB=Exit Base
E-LW = Electronic .77BF
MV= Multi Volt EMB = Emergency Ballast
E-O = Electronic 1.18BF
Specify Cord Length
ASY = Asymmetrical Reflector
96T8HO = F96T8HO
(215) 953-6663 phone
Cord
(215) 953-6710 fax
Page 6
SM Series
Side Mounted Channel
Application:
This cost effective side
mount strip light is ideal for use in all
residential, commercial and industrial areas
where clearance is a problem and general
lighting is desired.
reflectivity. Snap on sockets, ends, and
ballast cover allow for tool free assembly.
All units
Mounting:
Unit is equipped with
knockouts and holes for pendant or surface
mounting. This fixture can be mounted
individually or in continuous run. 7/8” knock
out is provided in end plate for conduit
connector.
20
80%
70%
50%
RW 70
50 30 10 70 50 30 10 50 30 10
102
102
102
102
95
95
95
95
80
80 80
0
92 88 83 80 85 81 77 74 60 65 63
1
84 76 70 64 77 70 65 60 59 55 51
2
76 67 59 53 70 61 55 50 52 47 43
3
69 59 51 45 64 54 47 42 46 41 36
4
63 52 51 45 58 48 41 35 41 35 31
5
58 46 38 32 53 43 35 30 36 30 26
6
53 41 33 28 49 38 31 26 33 27 23
7
49 37 29 24 45 34 27 23 29 24 20
8
45 33 26 21 42 34 24 20 26 21 17
9
10 42 30 23 18 39 28 22 17 24 19 15
RF
RC
T12
T8
T5
T5HO
Length
F14T12
------15”
F15T12
------18”
F20T12 F17T8 F14T5 F24T5HO
24”
F30T12 F25T8 F21T5 F39T5HO
36”
F40T12 F32T8 F28T5 F54T5HO
48”
For Tandem Units:
Maximum Weight = 9 lbs. / 48”.
Model
SM-
# Lamps
Lamp Type
1
1 = One
2 = Two
SM
Tandem
21 = Single
22 = Double
Fixture Length
Photometric Curve
Ballast
32
T12 Lamps
14 = F14T12
15 = F15T12
20 = F20T12
30 = F30T12
40 = F40T12
T8 Lamps
17 = F17T8
25 = F25T8
32 = F32T8
40T8 = F40T8
Voltage
Options
Cord
E
T5 Lamps
14T5 = F14T5
21T5 = F21T5
28T5 = F28T5
T5 High Output
24T5HO = F24T5HO
39T5HO = F39T5HO
54T5HO = F54T5HO
M = Magnetic
E-O = Electronic 1.18 BF
(215) 953-6663 phone
O = Grounded Outlet
Blank = 120V
TOG = Toggle Switch
277 = 277 V
ROC = Rocker Switch
MV= Multi Volt
PULL = Pull Switch
(215) 953-6710 fax
Page 7
CP-XE=Exit End
CP-XS=Exit Side
CP-XB=Exit Base
Specify Cord Length
RA Series
Right Angle Channels
Application: This cost effective right angle strip
is ideal for use in all residential, commercial, and
institutional areas where clearance and spacing
is a problem and general lighting is desired.
Construction: This unit is designed from heavy
gauge die formed steel and is finished in baked
maximum durability and reflectivity. Snap on
sockets, end plates, and ballast cover allow for
tool free assembly.
Standards.
holes for pendant or surface mounting. This
fixture can be mounted individually or in
continuous run. 7/8” knock out is provided in end
plate for conduit connector.
Fixture Length
T12
F14T12
F15T12
F20T12
F30T12
F40T12
T8
----F17T8
F25T8
F32T8
T5
----F14T5
F21T5
F28T5
T5HO
----F24T5HO
F39T5HO
F54T5HO
Length
15”
18”
24”
36”
48”
For Tandem Units:
Model
# Lamps
Lamp Type
Ballast
RA-
2
32
E
2 = Two
RA
Tandem
22 = Double
T8 Lamps
17 = F17T8
25 = F25T8
32 = F32T8
40T8= F40T8
T12 Lamps
14 = F14T12
15 = F15T12
20 = F20T12
30 = F30T12
40 = F40T12
T5 Lamps
14T5 = F14T5
21T5 = F21T5
28T5 = F28T5
T5 High Output
24T5HO = F24T5HO
39T5HO = F39T5HO
54T5HO = F54T5HO
Options
O = Grounded Outlet
M = Magnetic
Blank = 120V
TOG = Toggle Switch
277 = 277 V
ROC = Rocker Switch
E-LW =Electronic .77BF MV= Multi Volt
PULL = Pull Switch
E-O = Electronic 1.18
(215) 953-6663 phone
Voltage
Cord
CP-XE=Exit End
CP-XS=Exit Side
CP-XB=Exit Base
Specify Cord Length
(215) 953-6710 fax
Page 8
ST Series
Stagger Series
Application: This cost effective stagger
strip light is ideal for use in most
commercial areas. The unit is especially
designed for display lighting where
continuous mounting “black spots” are a
problem.
reflectivity.
Socket
bar,
end
plate
combination is riveted or screwed into
fixture for maximum bulb support.
All units
Mounting:
provisions for surface or pendant mounting
and installed in a continuous run. 7/8”
knockout is provided in end plate for
conduit connector.
Photometric Curve
20
80%
70%
50%
RW 70
50 30 10 70 50 30 10 50 30 10
0 102 102 102 102 98 98 98 98 89 89 89
91 86 82 78 87 83 79 75 76 72 70
1
82 74 67 62 78 71 65 60 65 60 56
2
75 65 57 51 71 62 55 49 57 51 46
3
68 57 48 42 64 54 47 41 50 44 39
4
62 50 41 35 58 48 40 34 44 37 32
5
56 44 36 30 54 42 35 29 39 32 27
6
52 39 31 26 49 38 30 25 35 28 24
7
48 35 27 22 45 43 26 21 31 25 20
8
44 32 24 19 42 30 23 18 28 22 17
9
10 41 29 21 16 39 28 21 16 25 19 15
Fixture Length
RF
RC
T12
F14T12
F15T12
F20T12
F30T12
F40T12
T8
T5
T5HO
Length
------17 5/16”
------20 5/16”
F17T8 F14T5 F24T5HO 26 5/16”
F25T8 F21T5 F39T5HO 38 5/16”
F32T8 F28T5 F54T5HO 50 5/16”
For Tandem Units:
Model
# Lamps
Lamp Type
Ballast
ST-
2
32
E
2 = Two
ST
Tandem
22 = Double
T12 Lamps
14 = F14T12
15 = F15T12
20 = F20T12
30 = F30T12
40 = F40T12
T8 Lamps
17 = F17T8
25 = F25T8
32 = F32T8
T5 Lamps
14T5 = F14T5
21T5 = F21T5
28T5 = F28T5
T5 High Output
24T5HO = F24T5HO
39T5HO = F39T5HO
54T5HO = F54T5HO
M = Magnetic
Blank = 120V
277 = 277 V
MV= Multi Volt
(215) 953-6663 phone
Voltage
Options
Cord
O = Grounded Outlet
TOG = Toggle Switch
ROC = Rocker Switch
PULL = Pull Switch
CP-XE=Exit End
CP-XS=Exit Side
CP-XB=Exit Base
Specify Cord Length
(215) 953-6710 fax
Page 9
EKD Series
Economy Industrial Units
Application: This economy shop light unit
is ideal for use in all industrial areas were
increased light levels are desired.
reflectivity. Reflector, socket bar, and end
plate, snap-on allowing for tool–free
assembly. End plate doubles as coupler
and aligner when fixture is used in
continuous run. Symmetric and asymmetric
reflectors are available.
All units
Mounting:
Fixture is equipped with
provisions for surface mounting, pendant
mounting, or chain hanging and can be
installed either individually or in continuous
runs. 7/8” knockout is provided in end plate
for conduit connector.
20
80%
70%
50%
RW 70
50 30 10 70 50 30 10 50 30 10
0 102 102 102 102 100 100 100 100 95 95 95
1 94 90 86 83 91 88 85 82 84 82 79
2 85 79 73 68 83 77 72 68 71 68 64
3 78 68 63 57 76 68 62 57 66 60 56
4 71 61 54 48 69 60 53 48 58 52 47
5 65 54 46 40 63 53 46 40 51 45 40
6 59 48 40 35 58 47 40 34 46 39 34
7 55 43 35 30 53 42 35 30 41 34 29
8 50 38 31 25 40 38 30 25 36 30 25
9 46 34 27 22 45 34 26 22 33 26 22
10 43 31 24 19 42 30 24 19 30 23 19
RF
RC
Maximum Weight = 15 lbs./ 48”
Fixture Length
Photometric Curve
T12
T12HO
F40T12
F48T12HO
---
---
F72T12
F72T12HO
F96T12
F96T12H0
T8
T8HO
Length
48”
F40T8
--F35T5 F80T5HO
60”
--------72”
F96T8 F96T8HO
----96”
For Tandem Units:
F32T8
---
T5
T5HO
F28T5 F54T5HO
30 lbs./ 96”
Model
# Lamps
Lamp Type
Ballast
EKD-
2
32
E
Voltage
1 = One
2 = Two
EKD
(for T8 / T12)
EHD
(T12 High
Output)
Double Tube Unit
T5 Lamps
28T5 = F28T5
35T5 = F35T5
T5HO Lamps
TANDEM
54T5 = F54T5HO
80T5 = F80T5HO
One Row
T8 Lamps
21 = Two Tube
17= F17T8
31 = Three Tube
32 = F32T8
41 = Four Tube
40T8 =F40T8
Two Row
96T8= F96T8
22 = Double
Three Row
23= Triple
T8 High Output
96T8HO = F96T8HO
T12Lamps
40 = F40T12
72 = F72T12
96= F96T12
T12 High Output
48HO = F48T12HO
72HO = F72T12HO
96HO = F96T12HO
(215) 953-6663 phone
M = Magnetic
E = Electronic .88BF
Blank = 120V
E-LW =Electronic .77BF 277 = 277 V
E-O = Electronic 1.18BF MV= Multi Volt
Options
O = Grounded Outlet
TOG = Toggle Switch
ROC = Rocker Switch
PULL = Pull Switch
WG = Wire Ground
SYM = Symmetrical
Reflector
ASY =Asymmetrical
Reflector
Cord
CP-XE=Exit End
CP-XS=Exit Side
CP-XB=Exit Base
Specify Cord Length
(215) 953-6710 fax
Page 10
SPT Series
Turrett Industrial Units
Application: This quality turret unit with
reflector is designed for use in most
industrial areas. Wide tube spacing and
reflector provide maximum down light and
increases light levels in workshops,
warehouses, and production areas.
Construction: The turret industrial unit is
designed from heavy gauge die formed
steel and finished in a baked white enamel
finish or polyester powder coating for
superior reflectivity and durability. Turrett
socket bar provides additional tube support
and greater light distribution. Hand turning
cam locks allow tool free reflector removal
and easy maintenance.
All units
Mounting: Fixtures are designed with
holes and knockouts making it suitable for
surface mounting, chain hanging, or
pendant mounting for individual or
continuous run. Knockout in end plates are
for use with conduit connectors.
RF
RC
RW
0
1
2
3
4
5
6
7
8
9
10
20
80%
70%
50%
70 50 30 10 70 50 30 10 50 30 10
101 101 101 101 98 98 98 98 94 94 94
92 89 85 82 90 87 84 81 80 78 76
84 78 72 67 82 76 72 66 73 69 65
77 68 62 56 75 67 61 56 65 59 55
70 61 53 48 69 59 53 47 57 51 47
64 53 46 40 62 53 45 40 50 44 39
59 47 40 34 57 47 39 34 45 39 34
54 42 35 30 53 42 35 30 40 34 29
50 38 31 25 48 37 30 25 36 30 25
46 34 27 22 44 33 27 22 32 26 22
42 31 24 19 41 30 24 19 29 23 19
Photometric Curve
Fixture Length
T12
T12HO
F40T12
---
F32T8
98 ¾”
Lamp Type
Ballast
SPT-
2
32
E
Two Row
22 = Double Tube
--F96T8HO
Length
48”
49 ¼”
96”
TANDEM
F40T12
43 lbs. / 96”
One Row
21 = Two Tube
31 = Three Tube
41 = Four Tube
---
F48T12HO
# Lamps
SPT
T8HO
F96T12 F96T12H0 F96T8
Model
2 = Two
3 = Three
4 = Four
T8
F32T8
Voltage
Options
Cord
T8 Lamps
32 = F32T8
40T8 = F40T8
96T8 = F96T8
96T8HO = F96T8HO
T12 Lamps
40 = F40T12
M = Magnetic
Blank = 120V
277 = 277 V
MV= Multi Volt
T12 Single Pin
48 = F48T12
72 = F72T12
96 = F96T12
O = Grounded Outlet
TOG = Toggle Switch
CP-XE=Exit End
ROC = Rocker Switch
CP-XS=Exit Side
PULL = Pull Switch
CP-XB=Exit Base
WG = Wire Ground
Specify Cord Length
T12 High Output
48HO = F48T12HO
72HO = F72T12HO
96HO = F96T12HO
(215) 953-6663 phone
(215) 953-6710 fax
Page 11
201 Series
Wrap Around Surface Mount Units
Application: This surface mounted wrap
around unit is designed for use in most
commercial, residential, and institutional type
applications. The unit provides maximum light
output with minimum clearance.
Construction: Housing is designed from
in baked white enamel or polyester powder
coating for
maximum durability and
reflectivity. Clear acrylic prismatic wrap
around diffuser hinges from either side and
snaps on and off for easy maintenance.
Standard # 1598. All units comply with
This fixture can be mounted individually or
continuous run.
Fixture Length
20
80%
70%
50%
RW 70
50 30 10 70 50 30 10 50 30 10
0 80 80 80 80 78 78 78 78 73 73 73
1 74 72 68 66 72 69 67 64 65 63 62
2 68 63 59 55 66 61 58 54 58 55 53
3 63 56 51 48 61 55 51 47 53 49 46
4 58 51 45 41 56 49 44 41 47 43 40
5 53 45 40 35 52 44 39 35 42 38 34
6 49 41 35 31 48 40 35 31 38 34 30
7 46 37 31 27 44 36 31 27 35 30 27
8 42 33 28 24 41 33 27 24 31 27 23
9 39 30 24 21 38 29 24 21 28 24 20
10 36 27 22 18 35 27 22 18 26 21 18
RF
RC
Maximum Weight= 16 lbs. / 48”
32 lbs. / 96”
Model
# Lamps
201-
2
2 = Two
3 = Three
4 = Four
201
Photometric Curve
Double Row
22 = Four Tube
Four Row
24 = Eight Tube
T12
F20T12
F40T12
F96T12
T8
F17T8
F32T8
F96T8
T5
F14T5
F28T5
---
Length
24”
48”
96”
For Tandem Units:
Fixture
2 Tube
4 Tube
2 Tube in
4 Tube Housing
Bulb Spacing
5 3/8”
2 1/4”- 5 3/8” - 2 1/4”
Lamp Type
Ballast
32
E
7”
Voltage
Options
T5 lamps
14T5 = F14T5
28T5 = F28T5
T8 lamps
32 = F32T8
96T8 = F96T8
T12 lamps
20 = F20T12
40 = F40T12
M = Magnetic
E-LW = Electronic .77 BF
Blank = 120V
277 = 277 V
MV = Multi Volt
T12 Lamps
48 = F48T12
96 = F96T12
(215) 953-6663 phone
(215) 953-6710 fax
Page 12
ECW and ECWS Series
”Classroom” Surface Wrap Around Units
Application: This “Classroom” surface
mounted wrap around unit is designed for
use in most commercial, residential, and
institutional type applications. The unit
provides maximum light output and is
available in 1, 2, or 3 lamp options with or
without a specular mirror.
heavy gauge die formed and is finished in
baked white enamel or polyester powder
coating for maximum durability and
reflectivity. Clear acrylic prismatic wrap
around diffuser snaps on and off for easy
maintenance.
All units
Mounting:
knockouts and holes for pendant or surface
mounting. This Fixture can be mounted
individually or continuous run.
RF
20
RCCoefficients
80%
RW 70 50
0
80 80
1
74 72
2
68 63
3
63 56
4
58 51
5
53 45
6
49 41
7
46 37
8
42 33
9
39 30
10
36 27
70% Zonal Cavity
50%
Utilization
Method
30 70
10 50 30 10 50 30 10
80 78
80 78 78 78 73 73 73
68 72
66 69 67 64 65 63 62
59 66
55 61 58 54 58 55 53
51 61
48 55 51 47 53 49 46
45 56
41 49 44 41 47 43 40
40 52
35 44 39 35 42 38 34
35 48
31 40 35 31 38 34 30
31 44
27 36 31 27 35 30 27
28 41
24 33 27 24 31 27 23
24 38
21 29 24 21 28 24 20
22 35
18 27 22 18 26 21 18
Model
ECW ECW
(Standard)
4.50” deep
ECWS
(Shallow)
3.50” deep
1 Tube Photometric
Curve
Fixture Length
T5
Length
F32T8
F28T5
48”
F96T12
F96T8
---
96”
Lamp Type
Ballast
32
E
2
1 = One
2 = Two
3= Three
Single Row
21 = Two Tube
31 = Three Tube
41 = Four Tube
Double Row
22 = Four Tube
Triple Row
23 = Six Tube
T8
F40T12
For Tandem Units:
35 lbs. / 96”
# Lamps
T12
Voltage
Options
Blank = 120V
277 = 277 V
MV= Multi Volt
REF = Specular Mirror Reflector
T5 Lamps
28T5 = 28W 46”
T8 Lamps
32 = 32W 48
96T8= F96T8
T12 Lamps
40 = 40W 48”
96= F96T12
M = Magnetic
(215) 953-6663 phone
(215) 953-6710 fax
Page 13
161 & 261 Series
1’ x 4’ & 2’ x 4’ Surface Mounted Unit
Application: This Surface mounted unit is ideal for
use in commercial, residential, and institutional
areas. Available in two, four, and six lamp, this unit
offers a variety of light intensity and physical
dimensions to fill your lighting needs.
Construction: Housing is designed from heavy
gauge die formed steel and finished in a baked white
enamel for maximum reflectivity and durability.
Hinged steel door frame with mitered corners come
with slide latches which allow for easy relamping and
maintenance. Lens is clear non yellowing acrylic with
prismatic #12 pattern for even light distribution. Lens
options are available upon request.
Electrical: All units are furnished with UL listed class
P thermally protected ballast. Other voltages are
available upon request. Fixtures meet requirements
for UL luminaire standard # 1598. All units comply
with national energy standards.
holes for pendant or surface mounting. Knockouts in
ends enable fixture to be mounted in a continuous
run.
20
80%
70%
RW 70
50 30 10 70 50 30 10 50
80 80 80 80 79 79 79 79 75
0
75 72 69 67 73 70 68 66 67
1
69 64 60 57 67 63 59 56 60
2
64 57 52 49 62 56 52 48 54
3
59 51 46 42 57 51 46 42 49
4
54 46 40 36 53 45 40 36 44
5
50 41 36 32 49 41 35 32 40
6
46 37 32 28 45 37 32 28 36
7
42 34 28 24 41 33 28 24 32
8
39 30 25 21 38 30 24 21 29
9
10 36 27 22 19 35 27 22 19 26
RF
RC
50%
30 10
75 75
66 64
57 55
51 47
45 41
39 36
35 31
31 27
27 24
24 21
22 18
Photometric
Curve
Fixture Length
T12
F20T12
F40T12
T8
T5
F17T8
F14T5
F32T8
U Lamps
Length
24”
F28T5
48”
Biax
F031U
---
F32U6
F40BX
F40T12U6
---
-------
24”
24”
24”
Fixture
Fixture Width
A
B
1x4
12 3/8”
11 1/4”
2X2 & 2X4
24 3/8”
23 1/4”
Fixture
1x4
2x2 & 2x4
Model
# Lamps
161-
2
161 = 1’
Wide
261 = 2’
Wide
2 = Two
4 = Four
6 = Six
Lamp Type
Ballast
32
E
T8 Lamps
17 = F17T8
32 = F32T8
T12 Lamps
20 = F20T12
40 = F40T12
U Lamps
31T8U = FO31/U
32U6 = F32/U6
40U6 = F40/U6
T5 Lamps
14T5 = F14T5
21T5 = F21T5
Biax
40BX = F40BX
Voltage
M = Magnetic
Blank = 120V
E-LW =Electronic .77 BF 277 = 277 V
E-O = Electronic 1.18 BF MV= Multi Volt
(215) 953-6663 phone
Bulb Spacing
2 Lite
3 Lite
7
2 1/4”
4 Lite
2 1/4”
3 2/3”
5 1/2”
11
Options
Lens / Louvers
.125 = .125 “ Prismatic Lens
.156 = .156” Prismatic Lens
DD = Acrylic Deep Dish Lens
EGG = ½” White Egg Crate Louver
SIL = ¾” Silver Parabolic Louver
SIL2 = 1½” Silver Parabolic Louver
(215) 953-6710 fax
Page 14
VT Series
Vapor Tite Unit
Application: This fully weatherproof unit is
designed for use in areas of wet location.
Designed to withstand direct contact with rain
this unit is corrosion resistant and waterproof.
This unit is ideal in areas such as car washes,
store fronts, parking garages, kitchens, and
chemical plants. Vapor Tite unit is capable of
being hosed down for easy cleaning.
Constriction: Exterior housing is designed for
single piece injection molded fiberglass/plastic
combination blend. Neoprene gasket and
pressure locks ensure waterproof seal. Interior
unit has heavy gauge steel die formed housing
with baked white enamel finish for maximum
reflectivity and durability.
Standard # 1598. All units comply with National
Energy Standards.
Mounting: Vapor Tite Unit available with an
stainless steel external hanging bracket. VT
Series is watertight and must be drilled and
sealed for each surface mounting or chain
hanging application.
20
80%
70%
50%
RW 70
50 30 10 70 50 30 10 50 30 10
83 83 83 83 81 81 81 81 76 76 76
0
75 71 67 64 72 68 65 62 64 62 59
1
67 61 56 51 65 59 54 50 55 51 48
2
61 53 47 42 59 52 46 42 49 44 40
3
56 47 41 36 54 46 40 35 43 38 34
4
51 41 35 30 49 40 34 29 38 32 28
5
47 37 30 25 45 36 30 25 34 28 24
6
43 33 27 22 41 32 26 22 30 25 21
7
40 30 23 19 38 29 23 19 37 22 18
8
36 26 20 16 35 26 20 16 24 19 16
9
10 34 24 18 14 33 23 18 14 22 17 14
RF
RC
Maximium Weight = 15 lbs. / 48”
Photometric Curve
Fixture Length
T12
T12HO
T8
T8HO
---
F17T8
---
F14T5 F24T5HO
26”
F48T12HO
F32T8
---
F28T5 F54T5HO
50”
F96T12
F96T12H0
F96T8
F96T8HO
# Lamps
Lamp Type
Ballast
VT-
2
32
E
1 = One
2 = Two
3 = Three
T8 lamps
17 = F17T8
32 = F32T8
96T8 = F96T8
96T8HO = F96T8HO
T12 lamps
20 = F20T12
40 = F40T12
T12 Single Pins
48 = F48T12
96 = F96T12
T12 High Output
48HO = F48T12HO
96HO = F96T12HO
T5 Lamps
14T5 = F14T5
28T5 = F28T5
T5 lamps
24T5HO = F24T5HO
54T5HO = F54T5HO
(215) 953-6663 phone
Length
F40T12
32 lbs. / 96”
T5HO
F20T12
Model
VT = 50”
VTS = 98”
VTH = 98”
T5
---
---
98”
Voltage
M = Magnetic
Options
Blank = 120V EMB = Emergency HB = Hanging
277 = 277 V
Ballast
Bracket
MV= Multi Volt
(215) 953-6710 fax
Page 15
Mounting
CIT2
Series
Vapor Tite Unit
Application: This fully weatherproof T5 or T8
unit is designed for use in areas of wet location.
stainless
steel
pressure
locks
ensure
waterproof seal. Interior gear tray is heavy
gauge die formed steel which hinges to allow
electrical raceway access while remaining
attached to luminaire housing during installation
and maintenance.
Standard # 1598 wet location. All units comply
with National Energy Standards. NSF/ANSI
Standard 2 - Splash Zone
Mounting Brackets Included
Photometric Curve
RF
RC
80%
RW 70
50 30
0 109 109 109
98 93 89
1
89 80 73
2
81 70 62
3
74 62 53
4
67 54 45
5
61 48 39
6
56 43 35
7
52 39 30
8
48 35 27
9
44 31 24
10
T8
20
10
109
84
67
56
47
39
33
29
25
21
19
70
107
95
86
78
71
65
59
54
50
46
43
70%
50 30 10
107 107 107
91 86 83
78 72 66
68 61 55
60 52 46
53 45 38
47 39 33
42 34 28
38 30 24
34 25 21
31 23 18
50%
50 30
101 101
86 83
74 69
65 59
57 51
50 43
45 38
40 33
36 29
32 25
30 23
T5
F17T8 F14T5
76
59
48
40
34
28
24
21
18
16
14
Length
F24T5
28”
F32T8 F28T5 F54T5HO
Tandem 4’ Tubes
52”
T8
F96T8HO
# Lamps
Lamp Type
Ballast
CIT2 -
2
32
E
T8 lamps
17 = F17T8
32 = F32T8
T5 Lamps
2 = Two
14T5 = F14T5
28T5 = F28T5
T5 lamps
Tandem
22 = DoubleTandem 24T5HO = F25T5HO
54T5HO = F54T5HO
8’ Tubes
96T8 = F96T8
96T8HO = F96T8HO
4.25”
6.77”
100”
Voltage
Blank = 120V
E-LW = Electronic .77BF 277 = 277 V
(215) 953-6663 phone
100”
8 ft Tubes
T8HO
Length
F96T8
32 lbs. / 96”
4.25”
Length
FF32T8 F28T5 F54T5HO
Model
CIT 2
T5HO
Options
EMB = Emergency
Ballast
REF = Specular Aluminum
Reflector 95%
(215) 953-6710 fax
Mounting
HB = Hanging
Bracket
CIT4
Series
Vapor Tite Unit
stainless
steel
pressure
locks
ensure
and maintenance.
RF
RC
80%
RW 70
50 30
0 109 109 109
98 93 89
1
89 80 73
2
81 70 62
3
74 62 53
4
67 54 45
5
61 48 39
6
56 43 35
7
52 39 30
8
48 35 27
9
44 31 24
10
Photometric Curve
20
10
109
84
67
56
47
39
33
29
25
21
19
70
107
95
86
78
71
65
59
54
50
46
43
70%
50 30 10
107 107 107
91 86 83
78 72 66
68 61 55
60 52 46
53 45 38
47 39 33
42 34 28
38 30 24
34 25 21
31 23 18
50%
50 30
101 101
86 83
74 69
65 59
57 51
50 43
45 38
40 33
36 29
32 25
30 23
76
59
48
40
34
28
24
21
18
16
14
Fixture Length
T8
T5
T5HO
Length
F32T8 F28T5 F54T5HO
50”
32 lbs. / 96”
Model
# Lamps
Lamp Type
Ballast
CIT4 -
4
32
E
Voltage
T8 lamps
32 = F32T8
CIT4
4 = Four
T5 Lamps
28T5 = F28T5
Blank = 120V
277 = 277 V
MV= Multi Volt
Options
EMB = Emergency
Ballast
Reflector 95%
T5 lamps
54T5HO = F54T5HO
(215) 953-6663 phone
(215) 953-6710 fax
Mounting
HB = Hanging
Bracket
ALC Series
Aluminum Channel
Application:
Aluminum covered and
gasketed unit is designed for use in most
outdoor areas. ALC Series is ideal for such
areas as shopping centers, walkways, under
eves, dock areas, or any place that is not
directly in contact with the rain or chemicals.
Construction: Housing and end plates are
designed from heavy gauge die formed
aluminum that resists rust and corrosion.
Unit is finished in baked white enamel for
maximum
reflectivity
and
durability.
Neoprene and rubber gaskets ensure
moisture seal and protect components from
corrosion. Lens is extruded 100% clear
virgin acrylic that resists yellowing.
All units
Mounting: Knockouts available for both
pendant and surface mounting. This unit is
designed to be mounted individually or in a
continuous run.
20
80%
70%
50%
RW 70
50 30 10 70 50 30 10 50 30 10
0 105 105 105 105 99 99 99 99 89 89 89
1 92 87 82 77 87 82 78 74 74 70 67
2 83 74 66 60 78 70 63 58 62 57 53
3 75 64 56 49 70 61 53 47 54 48 43
4 68 56 47 41 64 53 45 39 48 41 36
5 62 49 40 33 59 46 38 32 42 35 30
6 56 43 35 28 53 41 33 27 37 30 25
7 52 39 30 24 49 37 29 23 33 26 21
8 48 35 26 21 45 33 25 20 30 23 18
9 44 31 23 18 41 30 22 17 27 20 16
10 41 28 21 16 39 27 20 15 24 18 14
RF
RC
Maximum Weight= 12 lbs. / 48”
Photometric Curve
Fixture Length
T12
T12HO
Length
48”
F72T12 F72T12HO
----72”
F96T12 F96T12H0 FT6T8 F96T8HO
96”
For Tandem Units:
F40T12
25 lbs. / 96”
F48T12HO
T8
T8HO
F32T8
---
Model
# Lamps
Lamp Type
Ballast
ALC-
1
32
E
1 = One
ALC
Tandem
21 = Two Tube
T8 Lamps
32 = F32T8
96T8 = F96T8
96T8HO = F96T8HO
T12 Lamps
40 = F40T12
T12 Single Pin
48 = F48T12
72 = F72T12
96 = F96T12
T12 High Output
48HO = F48T12HO
72HO = F72T12HO
96HO = F96T12HO
(215) 953-6663 phone
Voltage
M = Magnetic
Blank = 120V
277 = 277 V
MV = Multi Volt
Options
TOG = Toggle Switch
ROC = Rocker Switch
PULL = Pull Switch
(215) 953-6710 fax
Page 16
OD Series
Outdoor Billboard Sign Units
Application: This billboard unit provides
high light levels with even distribution, for
spot lighting. The unit is weather resistant
and suitable for most outdoor applications.
Construction: Housing is made of heavy
gauge extruded aluminum with die cast end
plates and splice box fittings. Housing
interior is finished in a baked enamel finish
for maximum reflectivity and durability.
Splice box is threaded for ¾” conduit and
contains adjusting screws for housing.
Lens is clear smooth slide-on acrylic that
resists yellowing.
All units
Mounting:
Units are designed to be
conduit
mounted
either
individually,
tandem, or in a continuous run.
Fixture Length
# of Lamps
T5HO
Length
1 or 2
F54T5HO
53”
F54T5HO
101”
TANDEM
Single or Double
For Tandem Units Multiply Unit above by 2
15 lbs. / 101”
Model
# Lamps
Lamp Type
Ballast
ODH-
2
T5HO
E
Voltage
1 = One
T5 HO Lamps
OD
Single Tube Tandem
21 = Single Tandem
54T5HO = F54T5HO
E = Internal T5 Electronic Ballast
Blank = 120V thru 277V
Double Tube Tandem
22 = Double tamdem
(215) 953-6663 phone
(215) 953-6710 fax
Page 17
VPC Series
Vandalproof Covered Channel
Application: This vandalproof covered channel
is designed to protect the light source from any
abuses such as severe impact and other forms
of vandalism. Virtually indestructible, this UV
stabilized polycarbonate enhanced prismatic
design produces the best security lens on the
market today.
gauge die formed steel is finished in a baked
maximum reflectivity and durability. Lens is
vacuum formed clear polycarbonate with UV
stabilizers. Neoprene gasket keeps fixture
weatherproof when surface mounting. Spanner
head screws are used to ensure tamper
resistance.
Listed Class P thermally protected ballast. Other
Standards.
Mounting: Knockouts are available for both
surface and pendant mounting.
.
RF
20
RC
80%
70%
50%
RW 70
50 30 70 50 30 50 30 10
58 55 52 56 53 50 50 47 45
1
53 48 44 51 46 43 43 40 38
2
49 43 38 47 41 37 39 35 37
3
45 38 33 43 37 32 35 31 28
4
41 34 29 40 33 29 31 27 24
5
38 31 26 37 30 26 29 25 22
6
36 28 23 34 27 23 26 22 19
7
33 26 21 32 25 21 24 20 17
8
31 23 19 30 23 19 22 18 15
9
10 28 21 16 27 20 16 19 16 13
Photometric Curve
Fixture Length
T12
T12HO
T8
F20T12
--F17T8
F40T12 F48T12HO F32T8
T5
F14T5
F28T5
T5HO Length
F24T5HO
26”
F54T5HO
51”
Model
# Lamps
Lamp Type
Ballast
VPC-
2
32
E
VPC
1 = One
2 = Two
T8 lamps
32 = F32T8
One Row
21 = Two Tube
T12 Lamps
20 = F20T12
Two Row
22 = Four Tube
40 = F40T12
T12 Single Pin
48 = F48T12
Options
T12 High Output
48HO = F48T12HO
T5 Lamps
14T5 = F14T5
28T5 = F28T5
M = Magnetic
Blank = 120V
277 = 277 V
E-LW =Electronic .77BF
MV= Multi Volt
WG = Wire Ground
T5 High Output
24T5HO = F24T5HO
54T5HO = F54T5HO
(215) 953-6663 phone
Voltage
(215) 953-6710 fax
Page 18
BUT Series
Covered Circline Fixtures
Application:
This economical surface
mounted Circline unit is available in a white
finish. This unit is for use in commercial
and residential areas such as restrooms,
closets, hallways, storage areas or any
small room area where genera lighting is
desired.
reflectivity. Pressurized bulbs clips ensure
centering and bulb support of Circline
bulbs.
All units
Mounting: Units are equipped with
knockouts for junction box or direct surface
mounting.
Fixture Diameter
Bulb
BUT-22
BUT-32
BUT-54
BUT-40
BUT-72
9 lbs. / 14”
B
11”
14”
14”
19”
19”
Model
Lamp Type
BUT-
Voltage
22
CIRCLINE LAMPS
BUT
A
10 1/8”
12 3/4”
12 3/4”
17”
17”
COMPACT FLUORESCENT (11”)
Single Tube
22 = (1) FC8T9
32 = (1) FC12T9
22/1-7
7 watt
40 = (1) FC16T9
9 watt
54 = (1) FC8T9 & (1) FC12T9 22/1-9
22/1-13
13
watt
72 = (1) FC12T9 & (1) FC16T9
(215) 953-6663 phone
COMPACT FLUORESCENT (14”)
Double Tube
Double Tube
22/2-7
7 watt
22/2-9
9 watt
22/2-13 13 watt
32/2-7
7 watt
32/2-9
9 watt
32/2-13 13 watt
Triple Tube
32/3-7
7 watt
32/3-9
9 watt
32/3-13 13 watt
Blank = 120V
277 = 277 V
MV = Multi Volt
(215) 953-6710 fax
Page 19
CL Series
Open Circline Fixtures
Application:
This
economical
surface
mounted Circline unit is available in both white
and chrome finish. This unit is for use in
commercial and residential areas such as
restrooms, closets, hallways, storage areas or
any small room area where genera lighting is
desired.
in baked white enamel or highly polished
chrome for maximum durability and reflectivity.
Pressurized bulb clips ensure centering and
bulb support.
Standard # 1598.
Mounting: Units are supplied with crossbar,
stem, nut and cap for easy mounting to
standard junction box.
Fixture is also
equipped with knockouts for junction box or
direct surface mounting.
Fixture Diameter
Lamp
1CL-22
1CL-32
2CL-54
B
3/16 KO
3/16 KO
3/16 KO
C
7/16 KO
7/16 KO
7/16 KO
Model
Lamp Type
1CL
32
1CL = One Lamp
2CL = Two Lamp
A Dia.
8 1/2”
11 5/16”
11 5/16”
22 = FC8T9
32 =FC12T9
54 =FC8T9 & FC12T9
Ballast
Voltage
Color
WH
Blank = Magnetic
(215) 953-6663 phone
Blank = 120V
277 = 277 V
MV= Multi Volt
WH = White
CH = Chrome
(215) 953-6710 fax
Page 20
318 Series
Undercabinet Unit
Application: This undercabinet fixture is
designed for use in areas with low clearance
and where high light levels are desired. It is
ideal for use in kitchens, hospitals, desk
areas, and bathrooms.
heavy gauge die formed steel and finished in
a baked white enamel or polyester powder
coating for maximum reflectivity and
durability. Lens is extruded white acrylic that
snaps on and off for easy relamping.
Standard # 1598.
Mounting: Every
keyhole slots for
without entering
knockouts provided
supply connection.
fixture is supplied with
easy surface mounting
ballast raceway. ½”
in ends and bottom for
Fixture Length
T8
F17T8
F25T8
F32T8
Length
24 1/16”
36 1/16”
48 1/16”
Model
# Lamps
Lamp Type
Ballast
318 -
1
32
E
1 = One
318
Single Row
21 = Two Tube
T8 Lamps
17 = F17T8
25 = F25T8
32 = F32T8
M = Magnetic
(215) 953-6663 phone
Voltage
Blank = 120V
277 = 277 V
Options
O = Grounded Outlet
TOG = Toggle Switch
ROC = Rocker Switch
PULL = Pull Switch
Cord
CP-XE=Exit End
CP-XS=Exit Side
CP-XB=Exit Base
Specify Cord Length
(215) 953-6710 fax
Page 21
320 Series
1” Deep Undercabinet Unit
Application: The shallowest of all fixtures,
this unique 1” deep unit is specially
designed for T-5 tubes to be mounted under
cabinet with flat, non recessed base. 320
series fixtures are ideal for use in kitchens,
hospitals, desk areas, and bathrooms.
heavy gauge die formed steel and finished
in a baked white enamel or polyester
powder coating for maximum reflectivity and
durability. Lens is extruded white acrylic that
snaps on and off for easy relamping.
All units
Mounting: Every fixture is supplied with
keyhole slots for easy surface mounting
without entering ballast raceway. ½”
knockouts provided in ends and bottom for
supply connection.
Fixture Length
T5
Length
F8T5
12”
F13T5
21”
F14T5
23”
F21T5
35”
F28T5
47”
For Tandem Units:
Multiply lamp length above by 2
Model
# Lamps
Lamp Type
Ballast
Voltage
End View
Options
Cord
3201 = One
320
Single Tandem
2 = Two Tube
T5 lamps
08 = F8T5
13 = F13T5
14T5 = F14T5
21T5 = F21T5
28T5 = F28T5
M = Magnetic
(215) 953-6663 phone
Blank = 120V
277 = 277 V
O = Grounded Outlet
TOG = Toggle Switch
ROC = Rocker Switch
PULL = Pull Switch
CP-XE=Exit End
CP-XS=Exit Side
CP-XB=Exit Base
Specify Cord Length
(215) 953-6710 fax
Page 22
1P Series
Chrome Covered Bathroom Wall Unit
Application: This covered chrome channel
can be mounted both vertically and
horizontally and comes in a variety of sizes
for a wide range of uses. It is Ideal for use in
bathrooms, kitchens, powder rooms, under
cabinets, or any area where high quality and
low cost lighting is preferred.
heavy gauge die formed steel and plated in a
high polished chrome for high grade
appearance. Off and on switch is standard in
end plate. Snap in grounded convenience
outlet is available upon request. End plates
are secured to fixture by acorn nuts. Lens is
extruded white acrylic.
Standard # 1598.
Mounting:
Holes and knockouts are
provided in units for surface or wall mounting
either vertically or horizontally.
Fixture Length
T12
F14T12
F15T12
F20T12
F30T12
F40T12
# Lamps
1P1P
1 = One
Length
15 1/2”
18 1/2”
24 1/2”
36 1/2”
48 1/2”
Model
T8
----F17T8
F25T8
F32T8
T8 Lamps
17 = F17T8
25 = F25T8
32 = F32T8
Ballast
32
E
T12 Lamps
15 = F15T12
20 = F20T12
30 = F30T12
40 = F40T12
(215) 953-6663 phone
Specifications Subject To Change without Notice
Lamp Type
M = Magnetic
E = Electronic .88
BF
Voltage
Blank = 120V
277 = 277 V
MV= Multi Volt
Options
O = Grounded Outlet
TOG = Toggle Switch
ROC = Rocker Switch
PULL = Pull Switch
(215) 953-6710 fax
Page 23
AP Series
Chrome Covered Bathroom Wall Unit
Application: This covered chrome channel can
be mounted both vertically and horizontally and
comes in a variety of sizes for a wide range of
uses. It is ideal for use in bathrooms, kitchens,
powder rooms, under cabinets, or any area where
high quality and low cost lighting is preferred.
gauge die formed steel and plated in a high
polished chrome for high grade appearance. Off
and on switch is standard in end plate. Snap in
grounded convenience outlet is available upon
request. End plates are secured to fixture by acorn
nuts. Lens is extruded white acrylic.
Class P thermally protected ballast. Other voltages
are available upon request. Fixtures meet
requirements for UL Luminaire Standard # 1598.
All units comply with National Energy Standards.
Mounting: Holes and knockouts are provided in
units for surface or wall mounting either vertically
or horizontally.
Fixture Length
T12
T8
Length
F15T12
---
18 1/2”
F20T12
F17T8
24 1/2”
F30T12
F25T8
36 1/2”
F40T12
F32T8
48 1/2”
Model
# Lamps
Lamp Type
Ballast
AP-
1
32
E
T8 lamps
17 = F17T8
25 = F25T8
32 = F32T8
AP
1 = One
2 = Two
T12 Lamps
15 = F15T12
20 = F20T12
30 = F30T12
40 = F40T12
M = Magnetic
E-LW = Electronic .77 BF
(215) 953-6663 phone
Voltage
Blank = 120V
277 = 277 V
MV = Multi Volt
Options
O = Grounded Outlet
TOG = Toggle Switch
ROC = Rocker Switch
PULL = Pull Switch
3 WAY = 3 Way System
(215) 953-6710 fax
Page 24
555 Series
Covered Wall Unit
Application: This covered wall unit is designed to
provide maximum lumen output in areas such as
hallways, bathrooms, kitchens, stairways, and
hospitals. An assortment of options in either single or
double lamp allows this utility wall and surface
mounted unit to satisfy a variety of lighting needs.
gauge die formed steel and finished in either baked
white enamel or polyester powder coating. Socket
plate is riveted to housing adding to the structural
support of the fixture. Lens is extruded white acrylic.
End plates are attached by acorn nuts and secure
the lens to the fixture.
Class P thermally protected ballast. Other voltages
are available upon request. Fixtures meet
requirements for UL Luminaire Standard # 1598. All
units comply with National Energy Standards.
Mounting: Unit is equipped with holes and 7/8”
knockouts in housing for surface mounting. Fixture
may be mounted individually or with optional joiner
bands may be used in a continuous run.
Fixture Length
T12
F15T12
F20T12
F30T12
F40T12
T12HO
T8 Length
----18”
--F17T8
24”
--F25T8
36”
F48T12HO F32T8
48”
Model
# Lamps
Lamp Type
Ballast
555-
2
32
E
Voltage
T8 Lamps
17 = F17T8
25 = F25T8
32 = F32T8
555
1 = One
2 = Two
T12 Lamps
15 = F15T12
20 = F20T12
30 = F30T12
40 = F40T12
M = Magnetic
(215) 953-6663 phone
Blank = 120V
277 = 277 V
MV= Multi Volt
Options
O = Grounded Outlet
TOG = Toggle Switch
ROC = Rocker Switch
PULL = Pull Switch
NL = Night Light
3WAY = 3 W ay System
(215) 953-6710 fax
Page 25
RDI-C 2x2 Series
Center Basket
Application:
This
attractive
2’x2’
combines
the
energy
efficient
balanced
illumination
,
consistent
is attractive
lamp replacement.
Model
Size
# Lamps
Lamp Type
Voltage
RDI-C
2X2
2
17
MV
Options
T5 Lamps
RDI-C
Recessed
Direct/Indirect
Center Basket
2x2
1 = One
2 = Two
3 = Three
14= F14T5
24 = F24T5HO
T8 Lamps
40BX = 40w Biax
50BX = 50w Biax
55BX = 55w Biax
Blank = 120V
277= 277 volt
MV = Multi
Volt
17 = F17T8
(215) 953-6663 phone
Biax / Twin Tube
(215) 953-6710 fax
RDI-C 2x4 Series
Center Basket
Application:
This
attractive
2’x4’
combines
the
energy
efficient
balanced
illumination
,
consistent
is attractive
lamp replacement.
Model
Size
# Lamps
Lamp Type
Voltage
RDI-C
2X4
2
32
MV
Options
T5 Lamps
RDI-C
Recessed
Direct/Indirect
Center Basket
2x4
1 = One
2 = Two
3 = Three
28 = F28T5
54 = F54T5HO
T8 Lamps
Blank = 120V
277= 277 volt
MV = Multi Volt
32 = F32T8
(215) 953-6663 phone
LED
48LED =20w LED
(215) 953-6710 fax
141 Series
1’x 2’ & 1’x 4’ Recessed Lay-In Troffer
Application: This unit is designed especially for
use for quick installation with inverted T Bar
ceilings. This troffer unit is for use in all office,
commercial, and institutional areas and is
available in a variety of options to suit your
needs.
Construction: Housing is die formed from
heavy gauge steel and finished in a baked white
enamel or polyester powder coating for
maximum reflectivity and durability. Hinged door
with mitered corners comes with slide latches
which
allow
for
easy
relamping
and
maintenance. Lens is clear prismatic nonyellowing acrylic for even light distribution. Lens
options available upon request.
Standards.
Mounting: Designed to lay into inverted T Bar
ceilings, all units are equipped with 7/8”
knockouts in top sides and end plates. Fixture is
furnished with leads attached to access plate
allowing for quick installation without entering
ballast compartment.
20
80%
70%
50%
RW 70
50 30 10 70 50 30 10 50 30
0 80 80 80 80 79 79 79 79 75 75
1 75 72 69 67 73 70 68 66 67 66
2 69 64 60 57 67 63 59 56 60 57
3 64 57 52 49 62 56 52 48 54 51
4 59 51 46 42 57 51 46 42 49 45
5 54 46 40 36 53 45 40 36 44 39
6 50 41 36 32 49 41 35 32 40 35
7 46 37 32 28 45 37 31 28 36 31
8 42 34 28 24 41 33 28 24 32 27
9 39 30 25 21 38 30 24 21 29 24
1 36 27 22 19 35 27 22 19 26 22
0
Fixture Length
RF
RC
Photometric Curve
10
75
64
55
47
41
36
41
27
24
21
18
T12
F20T12
T8
T5 Length
F17T8 F14T5 24”
F40T12
F32T8 F28T5
48”
Bulb Spacing
Bulb
Spacing
2 Lamp
4 1/2”
3 Lamp
2 1/2”
4 Lamp
2 3/8”
Model
Lamps
Lamp Type
Ballast
141-
2
32
E
Voltage
Options
Lens/Louver
T8 Lamps
17 = F17T8
32 = F32T8
141
1 = One
2 = Two
3 = Three
4 = Four
T12 Lamps
20 = F20T12
40 = F40T12
M = Magnetic
Blank = 120V
277 = 277 V
MV= Multi Volt
T5 Lamps
14T8 = F14T5
28T5 = F28T5
(215) 953-6663 phone
SIL2 = 1½” Silver Parabolic Louver
(215) 953-6710 fax
Page 26
241 Series
2X2 & 2x4 Recessed Lay In Troffer
Application: This Unit is designed especially for
use for quick installation with inverted T Bar
ceilings. This Troffer unit is for use in all office,
commercial, and institutional areas and is
available in a variety of options to suit your needs.
Construction:
Housing is die formed from
heavy gauge steel and is finished in a baked white
enamel or polyester powder coating for maximum
reflectivity and durability. Hinged door with mitered
corners comes with slide latches which allow for
easy relamping and maintenance. Lens is clear
prismatic non yellowing acrylic for even light
distribution. Lens options available upon request.
voltages are available upon request. Fixtures meet
requirements for UL Luminaire Standard # 1598.
All units comply with National Energy Standards.
All units are equipped with 7/8”
knockouts in top, sides and end plates. Designed
for use in inverted T Bar ceilings this fixture comes
with earthquake clips built into end plate.
Mounting:
RF
RC
RW
0
1
2
3
4
5
6
7
8
9
10
70
80
75
69
64
59
54
50
46
42
39
36
20
80%
70%
50%
50 30 10 70 50 30 10 50 30
80 80 80 79 79 79 79 75 75
72 69 67 73 70 68 66 67 66
64 60 57 67 63 59 56 60 57
57 52 49 62 56 52 48 54 51
51 46 42 57 51 46 42 49 45
46 40 36 53 45 40 36 44 39
41 36 32 49 41 35 32 40 35
37 32 28 45 37 31 28 36 31
34 28 24 41 33 28 24 32 27
30 25 21 38 30 24 21 29 24
27 22 19 35 27 22 19 26 22
10
75
64
55
47
41
36
31
27
24
21
18
#
Lamps
241
4
241
2 = Two
3 = Three
4 = Four
T12
T8
T5
Length
F20T12
F17T8
F14T5
24”
F40T12
F32T8
F28T5
48”
U Lamps
Biax
F031U
---
---
24”
F32U6
F40BX
---
24”
F40T12U6
---
---
24”
Model
Fixture Length
Photometric Curve
Lamp Type
Ballast
32
E
T8 Lamps
17 = F17T8
32 = F32T8
T12 Lamps
20 = F20T12
40 = F40T12
T5 lamps
14T5 = F14T5
28T5 = F28T5
U Lamps
31/U = F031/U (1 5/8”)
32U6 =F32/U6 ( 6”)
40U6 = F40T12U6
Biax
40BX = F40BX
Voltage
Blank = 120V
E-LW =Electronic .77BF 277 = 277 V
E-DIM = Dimming Unit
(215) 953-6663 phone
Bulb Spacing
A
B
2 Lamp
10 ½”
3 Lamp
6”
Lens/Louver
Options
.156 = .156” Prismatic Lens
SIL2 = 1½” Silver Parabolic
Louver
NYC = NYC Approved
RAD = Regresses Alum
Door
(215) 953-6710 fax
Page 27
4 Lamp
5”
5 ½”
241 Deep Series
2’x 2’ & 2’x 4’ Recessed Deep Parabolic Troffer
Application:
This Unit is designed
especially for use for quick installation with
inverted T Bar ceilings. This Troffer unit is for
use in all office, commercial, and institutional
areas and is available in a variety of options
to suit your needs.
Construction: Housing is die formed from
heavy gauge steel and is finished in a baked
white enamel or polyester powder coat
interior for maximum reflectivity and
durability. Three inch deep aluminum
parabolic hinged door with mitered corners
comes with slide latches which allow for easy
relamping and maintenance. Louver options
available upon request.
Standard # 1598. All units comply with
National Energy Standards .
Mounting: All units are equipped with 7/8”
knockouts in top, sides and end plates.
Designed for use in inverted T Bar ceilings
this fixture comes with earthquake clips built
into end plate.
20
80%
70%
50%
RW 70
50 30 10 70 50 30 10 50 30 10
0 80 80 80 80 79 79 79 79 75 75 75
1 75 72 69 67 73 70 68 66 67 66 64
2 69 64 60 57 67 63 59 56 60 57 55
3 64 57 52 49 62 56 52 48 54 51 47
4 59 51 46 42 57 51 46 42 49 45 41
5 54 46 40 36 53 45 40 36 44 39 36
6 50 41 36 32 49 41 35 32 40 35 31
7 46 37 32 28 45 37 31 28 36 31 27
8 42 34 28 24 41 33 28 24 32 27 24
9 39 30 25 21 38 30 24 21 29 24 21
10 36 27 22 19 35 27 22 19 26 22 18
RF
RC
Photometric Curve
# Lamps
241-
3
T8
F17T8
T5
F14T5
Length
24”
F40T12
F32T8
F28T5
48”
-------
24”
24”
24”
U Lamps
Biax
F031U
--F32U6
F40BX
F40T12U6
---
Model
Fixture Length
T12
F20T12
Lamp Type
Ballast
32
E
Bulb Spacing
A
B
2 Lamp
10 ½”
3 Lamp
6”
4 Lamp
5”
5 ½”
Voltage
3” Deep Parabolic Louvers
Blank = 120V
277 = 277 V
MV= Multi Volt
2’x2’ Series
9 CELL = 3” Deep 3x3
16 CELL = 3” Deep 4x4
2’x4’Series
12 CELL = 3” Deep 2 x 6
18 CELL = 3” Deep 3 x 6
24 CELL = 3” Deep 4 x 6
32 CELL = 3” Deep 4 x 8
Options
T8 Lamps
17 = F17T8
32 = F32T8
241
2 = Two
3 = Three
4 = Four
T12 lamps
20 = F20T12
40 = F40T12
T5 lamps
14T5 = F14T5
28T5 = F28T5
U lamps
31/U = F031/U(1 5/8”)
32U6 =F32/U6 (6”)
40U6 = F40T12/U6
Biax
40BX = F40BX
M = Magnetic
E- DIM = Dimming Unit
(215) 953-6663 phone
NYC = NYC Approved
RAD = Regresses Alum. Door
(215) 953-6710 fax
Page 28
131 Series
1x4, 2x2, 2x4 Flanged Recessed Plaster Ceiling Unit
Application:
This flanged plaster ceiling
recessed fixture is designed especially for use
in plaster or concealed type ceiling. Wide 1”
flange surrounds perimeter of fixture and
covers ceiling opening causing clean recessed
appearance.
heavy gauge die formed steel in baked white
enamel or polyester powder coating for
maximum reflectivity and durability. Hinged
steel door with mitered corners are equipped
with side latched allowing for easy relamping
and maintenance. Lens is clear prismatic nonyellowing acrylic.
Standard # 1598.
Mounting: Unilugs are installed in outer side
wall of fixture allowing fixture support with a
simple turn of a screw.
20
80%
70%
50%
RW 70
50 30 10 70 50 30 10 50 30 10
80 80 80 80 79 79 79 79 75 75 75
0
75 72 69 67 73 70 68 66 67 66 64
1
69 64 60 57 67 63 59 56 60 57 55
2
64 57 52 49 62 56 52 48 54 51 47
3
59 51 46 42 57 51 46 42 49 45 41
4
54 46 40 36 53 45 40 36 44 39 36
5
50 41 36 32 49 41 35 32 40 35 31
6
46 37 32 28 45 37 31 28 36 31 27
7
42 34 28 24 41 33 28 24 32 27 24
8
39 30 25 21 38 30 24 21 29 24 21
9
10 36 27 22 19 35 27 22 19 26 22 18
Photometric
Curve
T12
F20T12
RF
RC
F40T12
# Lamps
131-
131
F32T8
F28T5
U Lamps
F031U
F32U6
F40T12U6
Biax
----F40BX
------Ceiling Opening
Nom. Fixture Size
W
131
1X2
11 1/2”
131
1X4
11 1/2”
231
2X2
23 1/2”
231
2X4
23 1/2”
Model
Fixture Length
T8
T5
Length
F17T8
F14T5
24”
Lamp Type
Ballast
2
32
E
1 = One
2 = Two
3 = Three
4 = Four
T8 Lamps
17 = F17T8
32 = F32T8
T12 Lamps
20 = F20T12
40 = F40T12
T5 Lamps
14T5 = F14T5
28T5 = F28T5
U Lamps
31/U=F031/U 15/8”
32U6 = F32/U6 6”
40U6 = F40T12/U6
Biax
40BX = F40BX
Voltage
48”
24”
L
24 1/4”
48 1/4”
24 1/4”
48 1/4”
Options
M = Magnetic
Blank = 120V
REF = Mirror Aluminum Reflector
E-LW =Electronic .77 BF 277 = 277 V
RAD = Regresses Aluminum
E-O = Electronic 1.18 BF MV= Multi Volt
Door
E-DIM = Dimming Unit
(215) 953-6663 phone
Lens and Louvers
EG = ½” White Egg Crate
Louver
SIL2 = 1 ½” Silver Para. Louver
(215) 953-6710 fax
Page 29
EFL Series
Small Flood Light
Application:

Parking Areas

Perimeter Lighting

Entrances & Walkways

Waterfronts

Loading Platforms

Recreational Areas

Landscaping

Signage
Construction: One piece heavy duty die cast
aluminum with gasket for weather seal. ½”
tapped hole for optional photocell. Heavy duty
swivel provides directional flexibility. Diffuser
is a high impact tempered glass lens with
molded polycarbonate frame provides hinging
and locks up without screws. The reflector is a
one piece anodized aluminum reflector
provides controlled high intensity. This is
available in High Pressure Sodium.
Electrical: UL Listed for wet and damp
Locations
Mounting: This units mounts to most cast
outdoor boxes. Post Top Fitter available for
post mounting. This units is suitable indoor or
outdoor application.
Model
# Lamps
Lamp Type
EFL-
1
35-HPS
EFL
1 = One
Voltage
35-HPS = 35W
50-HPS = 50W
70-HPS = 70W
100-HPS = 100W
150-HPS = 150W
Blank = 120V
(215) 953-6663 phone
Options
CELL = Photocell
FITTER = Post Top Fitter
POLY = Polycarbonate Guard
WG = Wire Guard
(215) 953-6710 fax
Page 30
FL Series
Medium Flood Light
Application:

Warehouses

Tunnels

Loading Docks

Parking Garages

Apartment Buildings

Shopping Centers

Factory Entrances

Hospitals
Construction: Two piece heavy duty die cast
aluminum housing and door. Die cast swivel
allows for accurate adjustment of light beam
once installed.
Provision for photocell
included. The diffuser is High impact tempered
glass provided with silicone rubber gasket to
keep fixture water-tite. Diffuser secures to
housing door by means of four L shaped steel
brackets The reflector is anodized aluminum.
This unit is available in high pressure sodium
and metal halide.
Locations
Mounting: This units mounts to most cast
outdoor boxes. Post Top Fitter available for
post mounting. This units is suitable indoor or
outdoor application.
Model
# Lamps
FL-
1
FL -
1 = One
Lamp Type
High Pressure Sodium
35-HPS = 35W
50-HPS = 50W
70-HPS = 70W
100-HPS = 100W
150-HPS = 150W
(215) 953-6663 phone
Metal Halide
70MH = 70 W
100MH = 100 W
150MH = 150W
175MH = 175W
Voltage
Options
Blank = 120V
CELL = Photocell
FITTER = Post Top Fitter
POLY = Polycarbonate Guard
HPF = Capacitor to make unit HPF
(215) 953-6710 fax
Page 31
WPS Series
Small Wall Pack
Application:

Warehouses

Tunnels

Loading Docks

Parking Garages

Apartment Buildings

Shopping Centers

Factory Entrances

Hospitals
Construction:
Die cast aluminum with ¾”
openings for secure conduit connections and
photocell. Also provided with tab and four threaded
openings for securing the diffuser. Clear Prismatic,
injection molded, polycarbonate lens. Provided with
two tabs along the metal hinge pin and four screws
to secure the lens to the housing. Silicon gasket is
included to keep unit water-tite. The reflector is
multi-faceted anodized aluminum designed for
optimal performance which secures to housing by
means of two screws.
Electrical: UL Listed for wet and damp Locations
Mounting: Wall mount for indoor and outdoor use.
Model
WPS
WPS
Lamp Type
1
1= One
Voltage
Options
35-HPS
35-HPS = 35W
50-HPS = 50W
70-HPS = 70W
100-HPS = 100W
Blank = 120V
(215) 953-6663 phone
CELL = Photocell
PLATE = Mounting Plate
HPF = Capacitor to make Unit HPF
(215) 953-6710 fax
Page 32
WPM -WPL Series
Medium and Large Wall Pack
Application:

Warehouses

Tunnels

Loading Docks

Parking Garages

Apartment Buildings

Shopping Centers

Factory Entrances

Hospitals
Construction: Two Piece, die cast aluminum
housing. Front and back secured together by
two hinges and two screws. ½” tapped holes
are supplied for securing connections and
photocell. The Diffuser is .083 thick glass or
injection molded high impact polycarbonate
with interior and exterior prismatic surfaces
which allows for minimum glare and maximum
light distribution. Diffuser secured to housing
by steel clips with continuous line of silicon
gasket. The reflector is .063” thick aluminum.
Secures to housing by means of screws.
Locations
Mounting: Wall mount for indoor and outdoor
use.
Fixture
A
B
C
WPM
7 1/4”
14 1/4”
9”
WPL
9 3/8”
18 1/8”
9”
WPLD
13”
18 1/8”
9”
Fixture Size
WPM
WPL
Model
Lamps
Lamp Type
WPM
1
35-HPS
= Up To 150W HPS
Up To 175W MH
= Up To 250W HPS
Up To 250W MH
WPLD
1 = One
= Up To 1000W HPS
Up To 1000W MH
35-HPS = 35W
50-HPS = 50W
70-HPS = 70W
100-HPS = 100W
150-HPS = 150 W
200-HPS = 200W
250-HPS = 250W
400-HPS = 400W
1000-HPS = 1000W
Metal Halide
100MH = 100W
175MH = 175W
250MH = 250 W
400 MH = 400W
1000MH = 1000W
(215) 953-6663 phone
Voltage
Blank = 120/277V
Options
CELL = Photocell
480V = 480 Volt Ballast
WG = Stainless Steel Wire Guard
(215) 953-6710 fax
Page 33
SQ Series
Square Surface Mounted H.I.D.
Application:

Correctional Facilities

Recreation Areas

Institutions

Public Areas

Schools

Hotels

Shopping Centers

Terminals
Construction: Die cast heavy gauge
aluminum. Five stage powder coated finish.
A neoprene gasket eliminates moisture,
dust, and insects. Standard or tamper
resistant spanner head. The diffuser is a
multi patterned injection molded clear
prismatic polycarbonate with UV inhibitors
to minimize discoloration. Can also be
supplied in white prismatic. Drill points for
maximum security installations.
Electrical: Meets all UL Requirements for
wet locations for ceiling mount and damp
locations for walls.
Mounting: Wall or ceiling mount for indoor
or outdoor application
Model
# Lamps
Lamp Type
SQ-8
1
35-HPS
SQ-8 = 8” Square
Up To 70W HPS
Up To 100W MH
1 = One
SQ-12 = 12” Square
Up To 150W HPS
Up To 175W MH
35-HPS = 35W
50-HPS = 50W
70-HPS = 70W
100-HPS = 100W
150-HPS = 150 W
(215) 953-6663 phone
Metal Halide
100MH = 100W
175MH = 175W
Voltage
Blank = 120V
DT = 120/277V
Multi = Quad
HPF = NPF To HPF Capacitor 120V
480V =Multitap To 480 Volt
(215) 953-6710 fax
Page 34
EXT Series
LED Exit Sign
Slim and low profile LED exit
sign provides a crisp, clean
look and excellent energy
savings.
* Completely self contained
* Fully Automatic Operation
* Compact low profile in neutral finish
* Push to test switch
* Automatic, low voltage disconnect
* 120 or 277 VAC operation
* Injection Molded, V-O flame retardant
* High impact thermoplastic housing
* Charge rate/power on LED indicator light
* Energy consumption 3.2 watts red letters
* Energy consumption 3.8 watts for green
* LED lamp life of 25 years plus
* Listed for damp locations
* Universal Mounting Canopy for
* Side Mounting installation
* Top Mounting installation
* Standard AC units available
* Emergency units available
* Ni-cad battery on emergency (EM) units
Model
Canopy
Number of Faces
Letter Color
Housing Color
Operation
EXT
U
1
R
W
EM
EXT
U-Universal
1- Single Face
mounting
2- Double Face
canopy included
R-Red
G-Green
(215) 953-6663 phone
W-White
B-Black
Damp Location
EM-Battery Backup
Blank-AC Only
(215) 953-6710 fax
Page 35
Yes
2HD-EXT
LED Exit Sign
Slim and low profile LED
exit sign provides a crisp,
clean look and excellent
energy savings.
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
RH-1 Indoor
Remote Lamp Head
RH-1-WP Outdoor
Remote Lamp Head
Completely self contained
Fully Automatic Operation
Compact low profile in neutral finish
Push to test switch
Automatic, low voltage disconnect
120 or 277 VAC operation
Injection Molded, V-O flame retardant
High impact thermoplastic housing
Charge rate/power on LED indicator light
Energy consumption 3.2 watts red letters
Energy consumption 3.8 watts for green
LED lamp life of 25 years plus
Listed for damp locations
Universal Mounting Canopy for
Side Mounting installation
Top Mounting installation
Larger battery for remote capacity
Universal K/O chevrons
Good for damp locations
Remote Capable up to 2 additional heads
RH-2-WP Outdoor
Remote Lamp Head
Model
Canopy
Number of Faces
Letter Color
Housing Color
2HD-EXT
U
1
R
W
Remote Heads
Indoor
RH-1
2HD-EXT
U-Universal mounting canopy included
1- Single Face
2- Double Face
(215) 953-6663 phone
R-Red
G-Green
W-White
B-Black
Outdoor
RH-1-WP
RH-2-WP
(215) 953-6710 fax
Page 36
EL-EXT Series
LED Exit Sign
Slim and low profile LED
exit sign provides a crisp,
clean look and excellent
energy savings.
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Completely self contained
Fully Automatic Operation
Compact and low profile
Push to test switch
Automatic, low voltage disconnect
120 or 277 VAC operation
V-O flame retardant
Charge rate/power on LED indicator light
Energy consumption 3.2 watts red letters
Energy consumption 3.8 watts for green
LED lamp life of 25 years plus
Listed for damp locations
Universal Mounting Canopy for
Side Mounting installation
Top Mounting installation
Standard AC units available
Emergency units available
Ni-cad battery on emergency (EM) units
Surface mount edge lit
In field installation flexibility
Specifications Subject To Change Without
Notice
Model
Canopy
Number of Faces
Letter Color
Housing Color
Operation
EL-EXT
U
1
R
W
EM
EL-EXT
U-Universal
1- Single Face
mounting
2- Double Face
canopy included
RC-Red on Clear
GC-Green on Cllear
(215) 953-6663 phone
W-White
B-Black
Damp Location
EM-Battery Backup
Blank-AC Only
(215) 953-6710 fax
Page 37
Yes
R-1 Series
Emergency Lighting Unit
Decorative and
economical unit with EZ
install back plate feature
has modern appearance
and low maintenance.
* Fully automatic operation
* Compact, low profile design
* Neutral finish
* Universal mounting plate with EZ
connect
* Rapid labor saving installation
* 6-Volt maintenance free battery
* Environmentally-safe, solid state
charger
* Automatic, low voltage disconnect
(LVD)
* Universal 120V-277V transformer
* Injection molded V-O flame retardant
* Charge rate indicator light
* Power on indicator light
Model
Emergency Operation
Voltage Input
Wattage
Battery Voltage
Damp Location
Warranty
90 Min
90 Min
120V/277V
120V/277V
2X5.4W
2X5.4W
6V
6V
Yes
Yes
Yes
Yes
R-1
R-1
R-1B (Black)
(215) 953-6663 phone
(215) 953-6710 fax
Page 38
R-5HO Series
Emergency Lighting Unit
Decorative and economical
unit with EZ install back
plate feature has modern
appearance and low
maintenance.
* Fully automatic operation
* Compact, low profile design
* Neutral finish
* Universal mounting plate with EZ connect
* Rapid labor saving installation
* 6-Volt maintenance free battery
* Environmentally-safe, solid state charger
* Automatic, low voltage disconnect (LVD)
* Universal 120V-277V transformer
* Injection molded V-O flame retardant
* Charge rate indicator light
* Power on indicator light
* Remote capable up to 2 additional heads
RH-1 Indoor
Remote Lamp Head
RH-1-WP Outdoor
Remote Lamp Head
RH-2-WP Outdoor
Remote Lamp Head
Model
Watts For 1.5 hrs
Voltage
R-5HO
R-5HO
22
6
2
(215) 953-6663 phone
Total Connected Heads/Fixtures**
4 HRS
2 HRS
1/5 HRS
3
(Based on 5W lamps**)
4
Remote Heads
RH1
Indoor
RH-1
Outdoor
RH-1-WP
RH-2-WP
(215) 953-6710 fax
Page 39
Warranty
Yes
CIT2
Series
Vapor Tite Unit
stainless
steel
pressure
locks
ensure
and maintenance.
Mounting Brackets Included
Photometric Curve
RF
RC
80%
RW 70
50 30
0 109 109 109
98 93 89
1
89 80 73
2
81 70 62
3
74 62 53
4
67 54 45
5
61 48 39
6
56 43 35
7
52 39 30
8
48 35 27
9
44 31 24
10
T8
20
10
109
84
67
56
47
39
33
29
25
21
19
70
107
95
86
78
71
65
59
54
50
46
43
70%
50 30 10
107 107 107
91 86 83
78 72 66
68 61 55
60 52 46
53 45 38
47 39 33
42 34 28
38 30 24
34 25 21
31 23 18
50%
50 30
101 101
86 83
74 69
65 59
57 51
50 43
45 38
40 33
36 29
32 25
30 23
T5
F17T8 F14T5
76
59
48
40
34
28
24
21
18
16
14
Length
F24T5
28”
F32T8 F28T5 F54T5HO
Tandem 4’ Tubes
52”
T8
F96T8HO
# Lamps
Lamp Type
Ballast
CIT2 -
2
32
E
T8 lamps
17 = F17T8
32 = F32T8
T5 Lamps
2 = Two
14T5 = F14T5
28T5 = F28T5
T5 lamps
Tandem
22 = DoubleTandem 24T5HO = F25T5HO
54T5HO = F54T5HO
8’ Tubes
96T8 = F96T8
96T8HO = F96T8HO
4.25”
6.77”
100”
Voltage
Blank = 120V
E-LW = Electronic .77BF 277 = 277 V
(215) 953-6663 phone
100”
8 ft Tubes
T8HO
Length
F96T8
32 lbs. / 96”
4.25”
Length
FF32T8 F28T5 F54T5HO
Model
CIT 2
T5HO
Options
EMB = Emergency
Ballast
Reflector 95%
(215) 953-6710 fax
Mounting
HB = Hanging
Bracket

RDI-C 2x2 Series

Transcription

Similar documents

OIL LAMP

Electronic Metal Halide Ballasts for 39 Watt Lamps

Let`s BeClear

Instructions for installing the DJAuto HBM115

T8 Linear LED Tube - Texas Fluorescents

Daavlin M Series

Pookoo Industrial Co., Ltd.

Cera Arc BT 220-230-270W