Panasonic Poscap Catalog

Transcription

P63 POSCAP Line-up
P65 Guidelines and precautions
P67 Selection guide
P74 Technical data
P81 Each series
P101 Catalog Deletion and EOL models
P65 Guidelines and precautions
Technical data Selection guide
P62 POSCAP INDEX
P63 POSCAP Line-up
P67 Series system diagram
P68 Image of case size
P69 Products list
P71 Explanation of part numbers
P72 Packing specifications
P74 Recommended soldering condition
P75 Fundamental structure
P76 Characteristics
P80 Reliability
P81
P82
Surface mount type
INDEX
Conductive Polymer Tantalum Solid Capacitors
Conductive Polymer Tantalum
Solid Capacitors
P83
P84
P85
P89
P91
P93
P95
P96
P97
P99
TPU
TPH
TPG
TPSF
TPE
TPB
TPC
TPF
TA
TV
TH
TQC
P101 Catalog Deletion and EOL models
※ Yelloew letters ： Update
62
Guidelines and precautions for use
About capacitors
Please take note of the following points in order to make the best use of capacitor's
performance.
Please use capacitors within the range of specified performance after confirming
each capacitor's usage environment and circuit condition.
Please choose capacitors that match the lifetime of the intended circuit design.
The performance of capacitors is changed by the temperature or frequency.
Therefore, please consider these variations when designing the circuit.
Please buy capacitors from our official distributors. Otherwise there is no warranty.
Line-up
Conductive Polymer Aluminum Solid Capacitors
Conductive Polymer Tantalum Solid Capacitors
Considerations when using in
industrial equipment
To when capacitors are used in industrial equipment,
allow wider margin of capacitance, impedance and other
characteristics.
Polarity
OS-CON and POSCAP have polarity.
Please confirm the polarity prior to use. If it is used with
the reverse polarities, leakage current, shorter lifetime or
a short circuit may result.
There is no bi-polar model of the OS-CON and POSCAP.
Rating and category
The definition of rating and category is as follows.
Rated temperature:
The maximum ambient temperature at which rated
voltage may be continuously applied.
Operating temperature and
ripple current
Rated voltage:
The maximum direct voltage or peak value of pulse
voltage which may be applied continuously to a
capacitor at any temperature between the lower
category temperature and the rated temperature.
Set the operating temperature so that it falls within the
The range of ambient temperatures for which a capacitor
Do not apply current that exceeds the allowable ripple
has been designed to operate continuously;
current. When excessive ripple current is applied,
this is given by the lower and upper category
internal heat increases and reduces the lifetime.
temperature.
In case capacitors are used under the condition out of
Category voltage:
the specified frequency, ripple current shall not exceed
the value revised by the frequency coefficient.
5
Category temperature range:
range stipulated in this delivery specification.
The maximum voltage which may be applied continuously
to a capacitor at its upper limit of category temperature.
Parallel connection
Operating environment restrictions
Ripple current may be flowed to a capacitor that has
Do not use the capacitor in the following environments
lower impedance when a different kind of capacitor is
used in parallel.
Please be very careful of choosing models.
Please consider the balance of electric current when
more than two capacitors are connected in parallel.
Places where water, salt water or oil can directly fall on
it and pleces where dew condensation may form
Places with noxious gas (hydrogen sulfide, sulfurous
acid, nitrous acid, chlorine, ammonia, etc)
Places susceptible to ozone, ultraviolet rays and radiation
Places where vibration or shock exceeds the allowable
value as specified in the catalog or specification sheet
Places under direct sunlight
Applied voltage for designing
Do not apply voltages exceeding the full rated voltage.
If such voltage is applied, it may cause short circuit
even though it is just a moment.
90% and below of the rated voltage or category
voltage of the POSCAP is recommended. If the
rated voltage is 10V or over except for TQC series,
80% and below of the rated voltage or category
voltage is recommended.
The sum of the DC voltage plus the peak AC voltage
shall not exceed the rated voltage or category voltage.
The sum of the DC voltage plus the negative peak
AC voltage shall not allow reverse voltage.
Do not apply reverse voltage.
Please contact us when there is a concern that circuit
operation may cause reverse voltage.
Land pattern
Please design hole space and hole diameter of circuit
board for capacitor radial lead type,
or land patterns for capacitor SMD type with
consideration of the product dimension specified in the
catalog or specification sheet and the size tolerance.
Avoid locating heat-generating components around the
capacitor and on the underside of the PC board.
When a capacitor is mounted to the double sided circuit
board, avoid placing through holes under the capacitor.
Avoid having the printed wire under the capacitor.
Soldering
The soldering conditions as soldering iron, flow soldering, reflow soldering should be under the range prescribed in specifications.
If the specifications are not followed, there is a possibility of the cosmetic defection, the intensive increase of leakage
current or the capacitance reduction.
Soldering heat stress to capacitor varies depending on temperature, duration time, mounting condition such as size,
material and component quantity of PC board. Please check the heat durability in your actual soldering condition.
6
Guidelines and precautions for use
About capacitors
Things to be noted before
mounting
Do not reuse capacitors that have been assembled in a
set and energized.
Leakage current may increase when capacitors are
stored for long term. In this case, we recommend you to
apply the rated voltage for 1 hour at 60℃ to 70℃ with
a resistor load of 1kΩ.
In case the capacitor has re-striking-voltage, please
apply the rated voltage to the capacitor through a
resistor load of 1kΩ.
Storage conditions
It is necessary to maintain a good storage environment
in order to prevent the problem when soldering due to
the degradation of solderability or moisturization of
molding resin.
When storing the reel in the storage bag, please
ensure that the storage bag is fully sealed.※
Do not store in high temperature and high humidity
environment.
For duration of storage, refer to the respective
"Guidelines and precautions for use" of each capacitor.
Do not store in damp conditions such as with water,
salt water, or oil, and dew condensation.
Do not store in places filled with noxious gas
Mounting 1
Please mount capacitors after confirming the polarity.
Please mount capacitors after confirming its rated
capacitance and rated voltage.
When mounting capacitors to the circuit board, please
use capacitors with the lead space matching the hole
space of the circuit board.
Do not drop capacitors or use capacitors dropped
beforehand.
(hydrogen sulfide, sulfurous acid, nitrous acid,
chlorine, ammonia, etc).
Do not store in places susceptible to ozone, ultraviolet
rays and radiation.
Please unseal storage bag just before mounting and
be conscious that the capacitors are used up.
Refer to the respective "Guidelines and precautions
for use" of each capacitor when some remain by
necessity.
※Only for capacitors packed by laminate bag.
Be careful not to deform the capacitor during installation.
Mounting 2
When an automatic inserter is used to clinch the
Capacitors comprise solid organic compounds, various
capacitor lead terminal, make sure it is not set too
metals, resin, rubber, etc. Treat them as industrial waste
strongly.
when disposing of it.
Be careful of the shock force that can be produced by
In case of disposing of a large amount of capacitor, we
absorbers, product chckers and centers on automatic
inserters and installers.
Do not apply excessive external force to the lead
terminal or the capacitor itself.
7
Disposal of capacitors
can dispose on your behalf.
OS-CON
Line-up
Guidelines and
precautions
Line-up
TPU
Small size
Low profile
Face down terminal
●
TPH
Small size
Low ESR
Face down terminal
●
Small size
Low profile
Large capacitance
● ●
Low ESR ・ Small size
Large capacitance
Face down terminal
● ● ●
82
Surface mount type
TPG
TPSF
83
84
Catalog Deletion and
EOL series
SMD type
Radial lead type
85 to 88
●
Low ESR
Products list
Explanation of
part numbers
Packing
specifications
Recommended
soldering
condition
Fundamental
structure
Ｃharacteristics
Reliability
Technical data
Image of
case size
Selection guide
Guidelines and
precautions
Series system
diagram
TPU
TPB
TPC
TPH
TPG
Surface mount type
TPSF
TPE
TPB
TPC
TPF
TA
TV
TH
TQC
EOL models
63
Size
code
Rated
Category
voltage Capacitance
temperature
range
range（℃）（Ｖ．ＤＣ） range（μＦ）
S09
−55 to ＋85
2.5 to 10
4.7 to 100
2.0×1.25
0.9
B09
−55 to ＋85
6.3
150
3.5×2.8
0.9
A09
−55 to ＋85
2.5 to 10
33 to 100
3.2×1.6
0.9
A14
−55 to ＋85
2.5 to 6.3 100 to 220
3.2×1.6
1.4
B1G −55 to ＋105 2.5 to 12.5 33 to 220
3.5×2.8
1.1
B15G −55 to ＋105 4.0 to 6.3 150 to 220
3.5×2.8
1.4
200
3.5×2.8
1.1
89 to 90
91 to 92
Standard
Low profile
●
2.5
H
L×W
（mm）（mm）
B1S
−55 to ＋105
B2S
−55 to ＋105 2.0 to 2.5
270
3.5×2.8
1.9
B2
−55 to ＋105 2.0 to 10
47 to 470
3.5×2.8
1.9
470
7.3×4.3
1.4
68 to 470
7.3×4.3
1.8
D3L
−55 to ＋105 2.5 to 10 220 to 680
7.3×4.3
2.8
D4
−55 to ＋105 2.5 to 10 330 to 1,500 7.3×4.3
3.8
B2
−55 to ＋105 4.0 to 10
3.5×2.8
1.9
D3L
−55 to ＋105 4.0 to 10 150 to 330
7.3×4.3
2.8
D4
−55 to ＋105 6.3 to 10 220 to 470
7.3×4.3
3.8
B1
−55 to ＋105 6.3 to 12.5
10 to 47
3.5×2.8
1.1
D2
−55 to ＋105 6.3 to 10
68 to 330
7.3×4.3
1.9
D15E −55 to ＋105
TPE
POSCAP
Line-up
●
For automotive
81
Technical data
High voltage
Features
Low ESR
Page
Large capacitance
Classification Series
Small size ・ Low profile
Selection guide
6.3
D2E −55 to ＋105 2.5 to 10
33 to 68
OS-CON
Line-up
Guidelines and
precautions
TA
93 to 94
95
Low ESR
Large capacitance
High reliability
(for the car electronics)
● ●
●
7.3×4.3
1.8
D3L
−55 to ＋105 2.5 to 10 150 to 680
7.3×4.3
2.8
D4
−55 to ＋105 2.5 to 6.3 470 to 1,000 7.3×4.3
3.8
B2
−55 to ＋105 4.0 to 10
47 to 100
3.5×2.8
1.9
D2E −55 to ＋105 2.5 to 10
68 to 470
7.3×4.3
1.8
−55 to ＋105 2.5 to 10 150 to 680
7.3×4.3
2.8
68 to 150
7.3×4.3
1.8
150
7.3×4.3
2.8
7.3×4.3
1.8
D3L
SMD type
TV
96
High reliability
Guaranteed at 125℃
(for the car electronics)
2.0
D2E −55 to ＋125 6.3 to 10
●
D3L
−55 to ＋125
10
D2E −55 to ＋125 2.5 to 6.3 150 to 330
TH
97 to 98
Guaranteed at 125℃
D2
−55 to ＋125 2.5 to 10
68 to 220
7.3×4.3
1.9
D3L
−55 to ＋125 4.0 to 6.3 220 to 330
7.3×4.3
2.8
D4
−55 to ＋125 4.0 to 10 220 to 470
7.3×4.3
3.8
3.5×2.8
1.4
B15 −55 to ＋105
99 to 100
High voltage
●
35
2.7
16 to 35
3.9 to 22
3.5×2.8
1.9
D12 −55 to ＋105
16
33
7.3×4.3
1.15
D15 −55 to ＋105
16 to 25
22 to 47
7.3×4.3
1.4
B2
TQC
Technical data
220 to 330
D2E −55 to ＋105
TPF
H
L×W
（mm）（mm）
D2
−55 to ＋105
−55 to ＋105
16 to 35
10 to 100
7.3×4.3
Surface mount type
Radial lead type
EOL series
POSCAP
Line-up
Guidelines and
precautions
Selection guide
Rated
Category
voltage Capacitance
temperature
range
range（℃）（Ｖ．ＤＣ） range（μＦ）
Technical data
Size
code
Series system
diagram
Image of
case size
Products list
Explanation of
part numbers
Packing
specifications
Recommended
soldering
condition
Fundamental
structure
Ｃharacteristics
Reliability
1.9
TPU
TPH
D3L
−55 to ＋105
16 to 20
100 to 150
7.3×4.3
2.8
TPG
TPSF
Surface mount type
For automotive
High voltage
Features
Low ESR
Page
Large capacitance
Classification Series
Small size ・ Low profile
Selection guide
TPE
TPB
TPC
TPF
TA
TV
TH
TQC
EOL models
64
OS-CON
Line-up
Guidelines and
precautions
Guidelines and
precautions
Selection guide
POSCAP is uniquely structured solid electrolytic capacitor. Please note the following points in order to take full advantage
of the POSCAP's performance and ensure the most stable quality.（The crucial precautions is described to page 5 to 7）
Technical data
Surface mount type
C ircuit designing cautions
1.Check the rated performance
5.Rapid charge and discharge limitation
After checking the operation and installation
environments,
design the circuit so that it falls within the rated
performance range stipulated in this delivery
specification.
Rapid charge and discharge are restricted (for
maintainance of high-proof reliability).
A protective circuit is recommended for when a
rapid charge or discharge causes excessive rush
current since this is main cause of short circuit and
large leakage current. Use a protective circuits in
case the rush current value exceeds 20A※.
Be sure to insert a protection resistor of about 1kΩ
for charge and discharge when measuring the
leakage current.
2.Operating temperature and ripple current
Radial lead type
EOL series
(a) Set the operating temperature so that it falls
within the range stipulated in this delivery
specification.
(b) Do not apply current that exceeds the
allowable ripple current. Ripple current should
be controlled
so that surface temperature of a capacitor do
not exceed the rated temperature.
(For questions regarding TQC series, please
contact us.)
POSCAP
Line-up
Image of
case size
Products list
Explanation of
part numbers
Packing
specifications
Recommended
soldering
condition
Fundamental
structure
Ｃharacteristics
Reliability
Technical data
Series system
diagram
Selection guide
Guidelines and
precautions
TPU
TPH
TPG
Surface mount type
TPSF
TPE
TPB
TPC
TPF
TA
3.Leakage current
Even when the soldering conditions fall within the
range of this delivery specifications, leakage
current increases a little on occasion. It also
increases a little during high temperature storage,
high humidity storage and temperature cycling
with no voltage applied. In cases such as these,
leakage current will decrease by applying voltage
under the condition of below the POSCAP's
maximum operating temperature. The speed at
which the leakage current is restored is increased
by applying voltage when the POSCAP's
temperature is close to the maximum operating
temperature.
4.Prohibited circuits
Since problems can be expected, POSCAP cannot
be used on the following circuits
(1) High impedance voltage retention circuits
TV
(2) Time constant circuits
(3) Circuits greatly affected by leakage current
TH
(4) The circuit in which two or more POSCAP are connected
TQC
EOL models
65
in a series so as to raise the endurance voltage.
※ When TH series use under the ambient temperature
more than 105℃ : 10A, TPU series : 10A
6.Protect circuit
The failure mode of POSCAP is the short mode.
When it breaks down, short electric current flows
to it.POSCAP gives off heat by this short current.
Do the following consideration in design fully for
the safety because it has a bad influence on the
part around POSCAP due to this heat.
・ A protective circuit and a protective device are set
up, so as to make the system safer.
・ A diffuse circuit and so on is set up, so as to make
the system safer such as that a machine may not
break down as to the single trouble.
7.Failure and life-span
The failure rate is 0.5% ＊ / 1,000h (Confidence
level：60%) based on JIS C 5003. The mainly failure modes are as follows.
＊ B2 size or less: 1.0%
7-1. Contingency failure
The main causes of failure are thermal
stresses cause by the soldering or thermal
use environment,
along with heat stresses, electrical stresses or
mechanical stresses. The most common
failure mode is a short circuit.
In case a short circuit occurs, ensure safety
by fully considering the followings.
(1) If POSCAP emit smoke, turn off the main power
of the equipment.In this case, keep your face and
hands away from the area.
OS-CON
Line-up
Guidelines and
precautions
Selection guide
Technical data
(2) It may take a few seconds to a few minutes
before POSCAP emits smoke by the situation.
Increase safety by using a protective circuit.
(3) If the smoke comes into eyes, rinse immediately.
If the smoke is inhaled, gargle immediately.
(4) In case a large current continues to flow
after a short circuit, in the worst case, the
10.Others
POSCAP’s Electrical characteristics are affected
by temperature and frequency fluctuations.
Design circuits after checking the amount of
fluctuation.
Surface mount type
shorted-out section may ignite. For safety,
install a redundant circuit or a protective circuit, etc.
Failure rate
In the case of the endurance which is 105℃ 2,000h.
0.5%/1,000h (Environment temp. : 105℃, Rated
voltage or Category voltage applied)
In the case of the endurance which is 105℃ 1,000h
or 125℃ 1,000h.
voltage or Category voltage applied)
In the case of the endurance which is 85℃ 1,000h.
voltage applied)
9.Considerations when soldering
The soldering conditions are to be within the
range prescribed in this delivery specification.
If the specifications are not followed, there is the
possibility of degradation of electric characteristic
and lifetime when soldering is conducted under
conditions that are harsher that those stipulated.
MSL
2a
Floor life
Time
Conditions
Applicable models
4 weeks ≦30℃／60％RH
3
168 hours ≦30℃／60％RH
5
48 hours ≦30℃／60％RH
See characteristics list
in Page 81 to 100
Radial lead type
EOL series
POSCAP
Line-up
Guidelines and
precautions
Selection guide
When POSCAP is used within the rated voltage, it
shows a stable characteristic,
but it may be damaged in a short circuit when an
overvoltage, for instance, is applied.
The time to reach the failure mode can be
extended by using POSCAP with reduced
environment temperature,
ripple current and applied voltage.
It is necessary to set an environment to prevent a
trouble at the time of soldering by the
degradation of solder ability or moisture's getting
into the molding resin when POSCAP are stored.
(Please refer to page 6. about the general storage conditions)
The storage period is 18 months or shorter after
shipment from factories,
under the condition that the storage bag is unopened.
Please unseal storage bag just before mounting
and be conscious that POSCAP in the storage bag
is used up.
When remainder unfortunately occurs, return them
to the storage bag once again and,
please seal the unsealed part by adhesive tape
etc., including desiccants. Moreover, once and use
it in time the storage bag is opened, store
POSCAP according to the table's Floor Life ''Time''
and ''conditions''
Technical data
8.Reduction of failure stress
Storage conditions
Series system
diagram
Image of
case size
Products list
Explanation of
part numbers
Packing
specifications
Recommended
soldering
condition
Fundamental
structure
Ｃharacteristics
Reliability
(Conform to IPC/JEDEC J-STD-020D)
TPU
TPH
Intellectual property right
We, Panasonic are providing the product and service
that customers can use without anxiety, and are
working positively on the protection of our products
under intellectual property rights.
Representative patents relating to POSCAP are as
follows:
( TPB, TPC, TPD, TPE, TPF, TPG, TPH, TPSF, TPU,
TA, TV, TH series )
U.S. Patent Nos. 6168639 and 6313979
TPG
TPSF
Surface mount type
7-2. Wear-out failure (lifetime)
When lifetime exceeded the specified
guarantee time of Endurance and Damp
heat, electrolyte might insulate and cause
electric characteristic changed. This is
called an open circuit. The electric
characteristics of capacitance and ESR may
possibly change within the specified range
in specifications when it is used under the
condition of the rated voltage, electric and
mechanical performance. Please note it
when design.
TPE
TPB
TPC
TPF
TA
TV
TH
TQC
EOL models
66
OS-CON
Line-up
Series system
diagram
Guidelines and
precautions
Selection guide
TPB
Standard
D4 size
P.91 to 92
Technical data
B2 size
4.0 to 10V
150 to 330μF
4.0 to 10V
33 to 68μF
P.85 to 88
TPC
P.81
TPE
Low profile
2.5 to 10V
330 to 1,500μF
B09 size
B1 size
D3L size
6.3 to 12.5V
10 to 47μF
6.3V
150μF
S09 size
D2E size
P.82
2.5 to 10V
68 to 470μF
Radial lead type
P.83
EOL series
Image of
case size
Products list
Explanation of
part numbers
Packing
specifications
Recommended
soldering
condition
Fundamental
structure
Ｃharacteristics
Reliability
Small size
Large capacitance
B15G size
2.5 to 6.3V
100 to 220μF
B2 size
B1G size
2.5 to 12.5V
33 to 220μF
4.0 to 6.3V
220 to 330μF
16 to 35V
10 to 100μF
B2 size
D2 size
D12 size
4.0 to 10V
47 to 100μF
2.5 to 10V
68 to 220μF
D2E size
16V
33μF
D15size
P.96
2.5 to 6.3V
150 to 330μF
16 to 25V
22 to 47μF
TV
High reliability
Guaranteed at 125˚C
(For the car electronics)
B2 size
D3L size
16 to 35V
3.9 to 22μF
10V
150μF
B15 size
D2E size
35V
2.7μF
6.3 to 10V
68 to 150μF
New
2.0 to 2.5V
270μF
D3L size
B1S size
2.5 to 10V
150 to 680μF
TPH
D2 size
2.5 to 10V
68 to 470μF
B2S size
2.5 to 6.3.V
470 to 1,000μF
TPU
16 to 20V
100 to 150μF
D2E size
D3L size
Low ESR
Large capacitance
Small size
D4 size
D3L size
2.5 to 10V
150 to 680μ
TPSF
Low ESR
Large capacitance
High voltage
D3L size
D4 size
P.84
TPF
TQC
TA
2.5 to 10V
33 to 100μF
P.93 to 94
P.99 to 100
High reliability
(For the car electronics)
A09 size
2.0 to 10V
47 to 470μF
Technical data
Series system
diagram
Selection guide
Guidelines and
precautions
A14 size
6.3V
470μF
2.5 to 6.3V
150 to 220μF
POSCAP
Line-up
TPH
Small size・Low profile
Face down terminal type
D15E size
TPG
TH
4.0 to 10V
220 to 470μF
2.5 to 10V
4.7 to 100μF
2.5 to 10V
220 to 680μF
P.95
Guaranteed
at 125˚C
Small size・Low profile
D4 size
6.3 to 10V
68 to 330μF
P.97 to 98
TPU
Low ESR
D2 size
Surface mount type
D3L size
6.3 to 10V
220 to 470μF
P.89 to 90
2.5V
200μF
New
TPG
Surface mount type
TPSF
TPE
TPB
TPC
TPF
TA
D2E size
2.0V
220 to 330μF
Case size
TH
TQC
EOL models
67
(Unit:mm)
S09
A09
A14
B09
B1
B1S
B1G
B15
B15G
B2
B2S
D12
D15
D15E
D2E
D2
D3L
D4
L
2.0
3.2
3.2
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
7.3
7.3
7.3
7.3
7.3
7.3
7.3
W
1.25
1.6
1.6
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
4.3
4.3
4.3
4.3
4.3
4.3
4.3
H
0.9
0.9
1.4
0.9
1.1
1.1
1.1
1.4
1.4
1.9
1.9
1.15
1.4
1.4
1.8
1.9
2.8
3.8
TV
The size of each photo is nearly to full scale.
OS-CON
Line-up
Image of
case size
Guidelines and
precautions
Selection guide
W
Technical data
H
L
(Unit:mm)
Surface mount type
(Unit:mm)
S09
size
A09
size
A14
size
B09
size
B1
size
B1S
size
B1G
size
B15
size
B15G
size
L2.0×W1.25×H0.9
L3.2×W1.6×H0.9
L3.2×W1.6×H1.4
L3.5×W2.8×H0.9
L3.5×W2.8×H1.1
L3.5×W2.8×H1.1
L3.5×W2.8×H1.1
L3.5×W2.8×H1.4
L3.5×W2.8×H1.4
P.81
P.82
P.82
P.81
P.91 to 92
P.84
P.83
P.99 to 100
P.83
TPU
TPH
TPH
TPU
TPC
TPSF
TPG
TQC
TPG
2.5 to 10V
4.7 to 100μF
2.5 to 10V
33 to 100μF
2.5 to 6.3V
100 to 220μF
6.3V
150μF
6.3 to 12.5V
10 to 47μF
2.5V
200μF
2.5 to 12.5V
33 to 220μF
New
35V
2.7μF
Radial lead type
2.5 to 6.3V
150 to 220μF
New
EOL series
POSCAP
Line-up
Guidelines and
precautions
B2S
size
D12
size
D15
size
D15E
size
D2E
size
D2
size
D3L
size
D4
size
L3.5×W2.8×H1.9
L3.5×W2.8×H1.9
L7.3×W4.3×H1.15
L7.3×W4.3×H1.4
L7.3×W4.3×H1.4
L7.3×W4.3×H1.8
L7.3×W4.3×H1.9
P.85
P.84
P.99 to 100
P.99 to 100
P.85
P.85
P.91
P.85
P.96
P.85
TPE
TPSF
TQC
TQC
TPE
TPE
TPC
TPE
TV
TPE
2.0 to 10V
47 to 470μF
2.0 to 2.5V
270μF
16V
33μF
16 to 25V
22 to 47μF
6.3V
470μF
L7.3×W4.3×H2.8
L7.3×W4.3×H3.8
2.5 to 10V
68 to 470μF
6.3 to 10V
68 to 330μF
2.5 to 10V
220 to 680μF
10V
150μF
2.5 to 10V
330 to 1,500μF
P.89 to 90
P.93 to 94
P.97 to 98
P.89 to 90
P.97 to 98
P.89 to 90
TPB
TPF
TH
TPB
TH
TPB
Technical data
B2
size
Selection guide
(Unit:mm)
Series system
diagram
Image of
case size
Products list
Explanation of
part numbers
Packing
specifications
Recommended
soldering
condition
Fundamental
structure
Ｃharacteristics
Reliability
TPU
2.0V
220 to 330μF
2.5 to 10V
68 to 220μF
4.0 to 10V
150 to 330μF
4.0 to 6.3V
220 to 330μF
6.3 to 10V
220 to 470μF
TPH
P.95
P.95
P.99 to 100
P.93 to 94
P.99 to 100
P.93 to 94
TPG
TPF
TPSF
TA
TA
TQC
P.99 to 100
P.96
P.95
P.97 to 98
TQC
TV
TA
TH
6.3 to 10V
68 to 150μF
2.5 to 10V
150 to 680μF
TQC
2.5 to 10V
68 to 470μF
16 to 35V
3.9 to 22μF
16 to 35V
10 to 100μF
TPF
4.0 to 10V
47 to 100μF
2.5 to 10V
150 to 680μF
16 to 20V
100 to 150μF
2.5 to 6.3V
470 to 1,000μF
4.0 to 10V
220 to 470μF
Surface mount type
4.0 to 10V
33 to 68μF
TPE
TPB
TPC
TPF
TA
P.97 to 98
TV
TH
TH
2.5 to 6.3V
150 to 330μF
The size of each photo is nearly to full scale.
TQC
EOL models
68
OS-CON
Line-up
Guidelines and
precautions
Products list
Selection guide
Size・ESR Matrix list
μF
V
2.7
Series
3.9
4.7
5.6
8.2
10
15
22
33
47
68
TPE
Technical data
2.0 TPF
TPSF
TPB
TPE
TPF
2.5
TPG
TPH
Surface mount type
TPSF
S09（150）
TPU
B2（70）
TPB
TPE
4.0 TPF
TPG
Radial lead type
TPH
A09（150）
TPU
S09（150）
B2（70）
TPB
TPC
EOL series
B1（70,55）
TPE
6.3
TPF
TPG
POSCAP
Line-up
TPH
Guidelines and
precautions
TPU
Products list
Explanation of
part numbers
Packing
specifications
Recommended
soldering
condition
Fundamental
structure
Ｃharacteristics
Reliability
Selection guide
Image of
case size
TPH
TPG
Surface mount type
TPE
TPB
TPC
TPF
TA
TQC
EOL models
B1G（70）
B2（70）
TPB
B2（70）
TPC
D2（45）
TPE
10
D2E（25）
B2（35）
TPF
TPG
B1G（70）
TPH
A09（150）
TPU
S09（300）
TPC
B1（80）
B1（80）
B2（100）
B2（90）
TPG
16
TQC
20
TQC
25
TQC
35
TQC
L
W
H
TH
S09（150）
B1（70）
TPG
Case size
TV
69
S09（150）
8.0 TPE
12.5
TPU
TPSF
S09（250）
TPC
Technical data
Series system
diagram
A09（150）
B1G（70）
D2（70）
D2（55,40） D2（50）
D12（40） D15（55）
B2（100）
D2（80）
D2（60）
B2（90）
B2（100）
D15（55）
D2（55）
D2（90,45） D2（60,45） D2（60）
B2（100） D15（70）
B15（300） B2（400）
S09
2.0
1.25
0.9
A09
3.2
1.6
0.9
A14
3.2
1.6
1.4
B09
3.5
2.8
0.9
D2（120）
B1
3.5
2.8
1.1
B1S
3.5
2.8
1.1
B1G
3.5
2.8
1.1
B15
3.5
2.8
1.4
B15G
3.5
2.8
1.4
B2
3.5
2.8
1.9
B2S
3.5
2.8
1.9
D12
7.3
4.3
1.15
D15
7.3
4.3
1.4
D15E
7.3
4.3
1.4
D2E
7.3
4.3
1.8
D2
7.3
4.3
1.9
（Unit:mm）
D3L
D4
7.3
7.3
4.3
4.3
2.8
3.8
OS-CON
Line-up
Guidelines and
precautions
Selection guide
V
μF
Series
100
120
150
200
220
270
2.0
D2E（6）
TPF
B2（35）
D2E
D4（15,12）
D3L（10,7,6）D3L（10,7,6） D4（6,5）
D4（5）
D4（5）
B15G（30）
A09（150）
A14（70）
Surface mount type
B2S（6★）
B1S（9★）
S09（150）
D3L（40）
TPB
4.0
Technical data
B1G（70）
TPSF
TPE
1,500
B2（35,15★,9★）
D3L（7）
TPG
TPU
1,000
D2E（＊3）（18,15,12,9,7）D3L（15,12）D4（15）
D2E（9,＊2）
B2
（35,25,21,15）
TPF
TPH
680
D2E（6）
B2（70）
TPE
2.5
470
B2S（9,6）
TPSF
TPB
330
B2（15,13） B2（11）
TPE
B2（35）
D2E（18）
D2E（＊1）
B2（35）
B2（35）
D2E（25,18） D3L（10,＊2）
D3L（12） D3L（10,5★） D4（10）
TPF
B15G（70）
TPG
A14（70）
TPH
TPU
D3L（40）
TPB
TPE
D2（45）
D2（40）
D2E（25,18） B2（35）
D2E（＊1）
D2E（25,18）
B2（35,25）
B2（35,25）
B2（25★）
D3L（9,＊1） D15E（35）
B2（35）
D4（10）
D3L（12.9,5）
D3L（9,5★）D4（10）
6.3
TPF
TPG
TPH
8.0
B1G（70,55,35★）
B15G（70,35）
D2（40）
D2E（25） D4（25,18）D4（25,18）
EOL series
B15G（35★）
POSCAP
Line-up
A09（100）
Guidelines and
precautions
A14（70）
TPU
B09（100）
TPC
D2（40）
TPE
Radial lead type
D4（40）
Selection guide
TPC
D3L（40） D4（35）
B2（35）
TPG
D3L（40）
TPB
10
D4（35）
D3L（40）
D2（45）
D3L（25,18）
TPE
TPF
Technical data
TPC
D4（40）
D4（25）
D3L（15）
TPG
TPH
Series system
diagram
Image of
case size
Products list
Explanation of
part numbers
Packing
specifications
Recommended
soldering
condition
Fundamental
structure
Ｃharacteristics
Reliability
TPU
TPU
TPC
TPH
TPG
16
TQC
20
TQC
25
TQC
35
TQC
D2（50）
D3L（50）
TPG
D3L（55）
★Under development
＊1(F:15, I:18, M:25)
TPSF
Surface mount type
12.5
＊2(C:12, F:15, I:18, M:25)
＊3(7, 9, C:12, F:15, I:18, M:25)
TPE
TPB
TPC
TPF
TA
･Symbols in table: Case size
･( ): ESR specitication(mΩmax.)
TV
TH
TQC
※ Red letters ： New models
EOL models
70
OS-CON
Line-up
Explanation of
part numbers
Guidelines and
precautions
Selection guide
Part number system
2R5
Technical data
Series name
3 to 4 figures
Rated
voltage
Series
Code
1.8
X
TPB
2.5
2R5orE
TPE
6.3
6
2.0
4.0
8.0
Surface mount type
TPB
Rated voltage
1 to 3 figures
2
4
8
10
10
12.5
12
11
16
20
25
35
11
16
20
25
35
Code
TPB
TPC
TPC
TPF
TPF
TPG
TPSF
TPSF
TAB
TAB
TPU
TAE
THB
4.7
4R7
5.6
8.2
10
TPU
22
15
33
47
56
THB
THC
TQC
TQC
TVE
2R7
3.9
TAE
68
82
THE
330
470
680
1,000
1,500
±20%
Code
M
10
15
22
33
47
56
68
82
150
270
Capacitance
tolerance
L
Special code
0 to 4 figures
8R2
150
220
M
Capacitance tolerance
1 figure
5R6
100
200
Radial lead type
3R9
100
120
TVE
Code
2.7
TPH
THC
THE
Rated
capacitance
TPE
TPG
TPH
330
Rated capacitance
2 to 4 figures
120
200
220
270
330
470
680
1000
1500
EOL series
Standard
POSCAP
Line-up
TPE series
Image of
case size
Products list
Explanation of
part numbers
Packing
specifications
Recommended
soldering
condition
Fundamental
structure
Ｃharacteristics
Reliability
Technical data
Series system
diagram
Selection guide
Guidelines and
precautions
B2 size
D15E size
D2E size
TPU
TPH
D3L size
TPG
Surface mount type
TPSF
TPE
TPB
TPC
TPF
TA
TV
TH
TQC
EOL models
71
B1G size
A09 size
A14 size
ESR 35mΩ max
ESR 30mΩ max
ESR 25mΩ max
ESR 21mΩ max
ESR 18mΩ max
ESR 15mΩ max
ESR 15mΩ/300kHz max
ESR 35mΩ max
85℃
ESR 30mΩ max
85℃
ESR 25mΩ max
85℃
ESR 15mΩ max
85℃
ESR 15mΩ/300kHz max 85℃
ESR 35mΩ max 85℃
ESR 25mΩ max
85℃
ESR 25mΩ max
ESR 18mΩ max
ESR 15mΩ max
ESR 12mΩ max
ESR 10mΩ max
ESR 25mΩ max 85℃
TPG series
ESR 35mΩ/300kHz max.
TPH series
ESR 150mΩ max
ESR 100mΩ max
ESR 70mΩ max
ESR 35mΩ max
TPB series
D3L size
TPC series
85℃
B1 size
Code
ZB
UB
PB
LB
IB
FB
FGB
AZB
AUB
APB
AFB
AFGB
ADGB
AJGB
AZU
AP
L
IL
FL
CL
AL
AL
A9EL
ZGD
AHA
AEA
ABC
AZC
L
A
B
Standard
TPF series
ESR 9mΩ max
ESR 7mΩ max
ESR 6mΩ max
D3L size
ESR 5mΩ max
ESR 5mΩ/500kHz max
ESR 10mΩ max
ESR 6mΩ max
D4 size
ESR 5mΩ max
TPSF series
B2S size
TPU series
S09 size
Ｂ09 size
TQC series
Capacitance enlarged type
Capacitance enlarged type(Ｂ size)
Capacitance enlarged type(D12 size)
All series
ESR 55mΩ max
ESR 45mΩ max
ESR 40mΩ max
ESR 35mΩ max
ESR 18mΩ max
ESR 15mΩ max
ESR 12mΩ max
ESR 9mΩ max
ESR 8mΩ max
ESR 6mΩ max
ESR 5mΩ max
ESR 9mΩ/300kHz max
ESR 6mΩ/500kHz max
ESR 4mΩ/500kHz max
Code
9L
7L
6L
5L
5EL
AH
6H
5H
AIG
SI
BI
YF
YFB
YFS
YFT
YFD
G
V
W
Z
I
F
C
9
8
6
5
ZG
UG
9G
6E
4E
OS-CON
Line-up
Packing
specifications
Guidelines and
precautions
*We supply only embossed taping type
Selection guide
Dimension of carrier tape
E
Component compartment
(Polarity)
D
Sprocket hole
J
(‒)
Technical data
B
C
A
(+)
K
t
G
F
H
Direction of unreeling
Surface mount type
(unit:mm)
A ±0.1
B
±0.1
C
±0.3
D
±0.1
E
F ±0.1
±0.1
G
±0.1
H
J
±0.1
＋0.1
−0
K ±0.2
t
±0.1
S09
1.65
2.4
8.0
3.5
1.75
4.0
2.0
4.0
φ1.5
1.3
0.25
A09
2.05
3.65
8.0
3.5
1.75
4.0
2.0
4.0
φ1.5
1.3
0.25
A14
2.05
3.65
8.0
3.5
1.75
4.0
2.0
4.0
φ1.5
1.7
0.25
B09
3.2
3.8
8.0
3.5
1.75
4.0
2.0
4.0
φ1.5
1.4
0.2
B1
3.2
3.8
8.0
3.5
1.75
4.0
2.0
4.0
φ1.5
1.4
0.2
B1S
3.25
3.9
8.0
3.5
1.75
4.0
2.0
4.0
φ1.5
1.7
0.25
B1G
3.25
3.9
8.0
3.5
1.75
4.0
2.0
4.0
φ1.5
1.7
0.25
B15
3.3
3.8
8.0
3.5
1.75
4.0
2.0
4.0
φ1.5
2.1
0.2
3.25
3.9
8.0
3.5
1.75
4.0
2.0
4.0
φ1.5
1.7
0.25
3.3
3.8
8.0
3.5
1.75
4.0
2.0
4.0
φ1.5
2.1
0.2
B15G
B2
B2S
3.25
4.0
8.0
3.5
1.75
4.0
2.0
4.0
φ1.5
2.1
0.25
D12
4.5
7.5
12.0
5.5
1.75
8.0
2.0
4.0
φ1.5
1.7
0.3
D15
4.5
7.5
12.0
5.5
1.75
8.0
2.0
4.0
φ1.5
2.4
0.3
D15E
4.7
7.8
12.0
5.5
1.75
8.0
2.0
4.0
φ1.5
1.7
0.3
D2E
4.5
7.5
12.0
5.5
1.75
8.0
2.0
4.0
φ1.5
2.4
0.3
D2
4.5
7.5
12.0
5.5
1.75
8.0
2.0
4.0
φ1.5
2.4
0.3
D3L
4.5
7.7
12.0
5.5
1.75
8.0
2.0
4.0
φ1.5
3.2
0.3
D4
4.5
7.7
12.0
5.5
1.75
8.0
2.0
4.0
φ1.5
4.2
0.3
●Dimension A and B are the measure of compartment's inside bottom.
●The (+) Polarity of the chip is placed on right side towards the unreeling direction.
●Dimension of the topcover tape
EOL series
POSCAP
Line-up
Guidelines and
precautions
Technical data
Thickness of cover tape: 62±10μm
Radial lead type
Selection guide
Size
code
Width of cover tape: 9.5±0.2mm
5.5±0.2mm (φ180reel)
Series system
diagram
Image of
case size
Products list
Explanation of
part numbers
Packing
specifications
Recommended
soldering
condition
Fundamental
structure
Ｃharacteristics
Reliability
TPU
TPH
Reel dimension
TPSF
Surface mount type
A
B
C
TPG
TPE
TPB
TPC
TPF
TA
TV
(unit:mm)
A
B
C
W1
W2
W1
φ 330±2
φ 80±2
φ 13±0.2
13.5±0.5
17.5±1.0
W2
＋0
180−3
60±2
13±0.2
9±0.5
11.4±1.0
φ
φ
φ
TH
TQC
EOL models
72
OS-CON
Line-up
Packing
specifications
Guidelines and
precautions
Selection guide
Minimum packing quantity and weight
Size code
Quantity(pcs./Reel,φ180)
Typical weight(g)
Size code
Quantity(pcs./Reel,φ330)
Typical weight(g)
Technical data
Surface mount type
S09
3,000
200
D12
4,500
1,200
A09
3,000
200
D15
3,000
1,000
A14
2,500
200
D15E
4,000
1,000
B09
3,000
200
D2E
3,000
1,000
B1
3,000
200
D2
3,000
1,000
B1S
2,500
200
D3L
2,500
1,100
B1G
2,500
200
D4
2,000
1,200
B15
2,000
160
B15G
2,500
200
B2
2,000
200
B2S
2,000
200
φ180
φ330
Dimension of packing case
Radial lead type
b
(unit:mm)
Reel size
EOL series
a
POSCAP
Line-up
c
Series system
diagram
Image of
case size
Products list
Explanation of
part numbers
Selection guide
Guidelines and
precautions
a
90
120
b
240
360
c
240
360
Units per packing case
Pieces/case
Size code
Pieces/case
S09
15,000
D12
22,500
A09
15,000
D15
15,000
A14
12,500
D15E
20,000
B09
15,000
D2E
15,000
B1
15,000
D2
15,000
TPU
B1S
12,500
D3L
12,500
TPH
B1G
12,500
D4
10,000
B15
10,000
B15G
12,500
B2
10,000
B2S
10,000
Recommended
soldering
condition
Fundamental
structure
Ｃharacteristics
Reliability
Technical data
Size code
Packing
specifications
TPG
Surface mount type
TPSF
TPE
TPB
TPC
TPF
TA
TV
TH
TQC
EOL models
73
Recommended
soldering
condition
OS-CON
Line-up
Guidelines and
precautions
Selection guide
Recommended reflow soldering temperature profile
Temperature on the
surface of capacitor
The cycles of reflow soldering: Twice (max)
Peak temperature
5s max
240℃
200℃
Technical data
40s max
150℃
60s
max
120s max
30s max
Time(sec.)
Peak temperature 250℃ lead free reflow soldering profile
Surface mount type
Temperature on the
Peak temperature
5s max
250℃
220℃
40s max
180℃
150℃
60s
max
120s max
30s max
Radial lead type
Time(sec.)
Peak temperature 260℃ lead free reflow soldering profile
EOL series
The model of MSL"2a" is changed into MSL "3" with this reflow condition.(See page 66)
POSCAP
Line-up
5s max
217℃
200℃
150℃
180s max
90s max
Time(sec.)
6s max
Technical data
60s
max
TQC series
Temperature on the
Guidelines and
precautions
Selection guide
260℃
Series system
diagram
Image of
case size
Products list
Explanation of
part numbers
Packing
specifications
Recommended
soldering
condition
Fundamental
structure
Ｃharacteristics
Reliability
TPU
Peak temperature
TPH
10s max
250℃
TPG
217℃
200℃
180℃
150℃
60s max
120s max
70s max
Time(sec.)
TPSF
Surface mount type
Temperature on the
Peak temperature
TPE
TPB
TPC
TPF
TA
TV
Soldering with a soldering iron
Tip of a soldering iron: 350℃ max (TQC serise: 400℃ max)
Working time: 3sec. max (TQC serise: 5sec max)
TH
Power of a soldering iron: 30W max
(Do not let the tip of soldering iron touch the POSCAP itself. Do not subject the POSCAP itself to excessive stress when soldering.)
TQC
EOL models
74
OS-CON
Line-up
Fundamental
structure
Guidelines and
precautions
Selection guide
Technical data
1. Basic structure of POSCAP
The electrolytes make the difference in structure between the POSCAP and
the standard tantalum capacitor.
Capacitor
Tantalum capacitor
Electrolyte
Manganese dioxide
Conductive polymer
(Standard model)
Surface mount type
Silver adhesive
Carbon layer
Silver paste
Electrolyte
（Conductive polymer）
Molding resin
Tantalum oxide
Cathode
Anode
Radial lead type
Sintered tantalum
EOL series
POSCAP
Line-up
Image of
case size
Products list
Explanation of
part numbers
Packing
specifications
Recommended
soldering
condition
Fundamental
structure
Ｃharacteristics
Reliability
Technical data
Series system
diagram
Selection guide
Guidelines and
precautions
Tantalum wire
Sintered tantalum
POSCAP uses sintered tantalum
as the anode material.
An oxide layer formed on the
surface of the sintered tantalum
is used for the dielectric, and a
conductive polymer for the electrolyte.
Tantalum oxide
Electrolyte
（Conductive polymer）
Magnified cross-section of element
(Face down terminals model)
Carbon layer
Silver paste
Electrolyte
(Conductive polymer)
Molding resin
TPU
Magnified photo
TPH
Tantalum oxide
TPG
Surface mount type
TPSF
TPE
TPB
TPC
TPF
TA
Silver adhesive
Anode
Cathode
Sintered tantalum
Tantalum wire
TV
● The sintered tantalum has a porous structure, it makes a large surface area, which enables to have large capacitance.
TH
● The conductive polymer used for the electrolyte is high in electric conductivity and enables the low ESR.
TQC
EOL models
75
OS-CON
Line-up
Guidelines and
precautions
Ｃharacteristics
Selection guide
1. POSCAP Electrical characteristics
1-1. Frequency characteristics
100
Fig.A Impedance frequency characteristics
at 25℃
Impedance (Ω)
10
(POSCAP vs other type)
Technical data
A：POSCAP
6.3V/47μF (3.5x2.8x1.1mm)
B：Tantalum capacitor
6.3V/47μF (3.5x2.8x1.9mm)
C：Aluminum electrolytic capacitor
25V/47μF (φ5.0ｘH10.8mm)
1
Surface mount type
C
B
0.1
A
0.01
1k
10k
100k
1M
10M
Frequency (Hz)
100
Fig.B Impedance & ESR frequency characteristics (Several POSCAP models)
at 20℃
EOL series
Impedance
ESR
POSCAP
A: 2R5TPF470M6L
B: 2TPSF270M6E
10
POSCAP
Line-up
Guidelines and
precautions
Selection guide
1
0.1
B
A
Technical data
Impedance & ESR（Ω）
Radial lead type
0.01
0.001
1Ｋ
10K
100K
Frequency （Hz）
1M
Series system
diagram
Image of
case size
Products list
Explanation of
part numbers
Packing
specifications
Recommended
soldering
condition
Fundamental
structure
Ｃharacteristics
Reliability
TPU
10M
TPH
TPG
The greatest characteristic of POSCAP is the excellent frequency characteristics.
and enables the POSCAP to perform at the higher frequency levels.
Fig. A: Compares the POSCAP to an aluminum electrolytic and a tantalum capacitor.
The POSCAP's impedance is remarkably lower than the other capacitors at the
periphery of the resonance frequency.
TPSF
Surface mount type
Using a high conductive polymer for the electrolyte greatly improves the ESR characteristics
TPE
TPB
TPC
TPF
TA
Fig. B: Compares the impedance and ESR frequency characteristics of three different
TV
POSCAP series.
TH
The TPSF series has a low ESL characteristic which brings it to high resonance
frequency, it makes impedance be much lower in the range of high - frequency wave.
TQC
EOL models
76
OS-CON
Line-up
Guidelines and
precautions
Ｃharacteristics
Selection guide
1-2. Characteristics at high and low temperature
Fig.B Capacitance temperature characteristics
Fig.A ESR temperature characteristics
Technical data
100
（POSCAP vs Ceramic capacitor）
POSCAP
6TPC47MB
6TPC47MB
特性
)
Ceramic capacitor
6.3V/47μF(X5R)
（F特性
)
Ceramic capacitor
6.3V/10μF(Y5V)
（POSCAP vs Ceramic capacitor)
10
1
ESR（Ω）
Surface mount type
at 100kHz
Capacitance change （%）
10
20
0.1
0.01
POSCAP 6TPC47MB
Ceramic capacitor 6.3V/47μF (X5R)
Ceramic capacitor 6.3V/10μF (Y5V)
at 120Hz
0
-10
-20
-30
-40
-50
0.001
-55
Radial lead type
EOL series
-20
0
20
Temperature（℃）
85
105
-60
-55
-20
0
20
Temperature（℃）
85
105
The POSCAP has a characteristics of low and high temperature, which is little change
against temperature for the ESR.
The stability of ESR's temperature characteristics means the noise-clearing ability is little change against temperature.
The POSCAP is suitable for outdoor equipment which requires the temperature
characteristic flexibility.
POSCAP
Line-up
Guidelines and
precautions
Explanation of
part numbers
Packing
specifications
Recommended
soldering
condition
Fundamental
structure
Ｃharacteristics
Reliability
TPU
TPH
TPG
Surface mount type
TPSF
TPE
TPB
TPC
TPF
TA
TV
TH
TQC
EOL models
77
Comparison of bias characteristics
（POSCAP vs Ceramic capacitor)
20
Capacitance change (%)
Products list
Selection guide
Image of
case size
1-3. Bias characteristics
Technical data
Series system
diagram
The ceramic capacitor has bias
characteristics, which makes the
capacitance decrease when voltage is
applied to it. However, POSCAPs will show
no reduction in capacitance for applied
voltage, as long
as the applied voltage is within its rating.
Therefore,
you will be able to design without worrying
about capacitance changing when voltage
is applied.
at 120Hz
0
-20
-40
-60
-80
0
POSCAP（6TPE100MAZB）
Ceramic capacitor
(6.3V/100μF) X5R
1
2
3
4
Bias voltage (V)
5
6
OS-CON
Line-up
Guidelines and
precautions
Selection guide
1-4. Piezoelectric effect of the capacitor
When variable voltage is applied to ceramic capacitors that uses dielectrics with
piezoelectric characteristics (e.g. barium titanate), the voltage will cause vibration due
to the elasticity in the dielectric.
If the cyclic change is within the audio-frequency (20Hz to 20kHz), the vibration from
the capacitor travels to the PCB and it could generate noise inside the equipment.
This may be an unwanted effect depending on the product you are developing. Our
POSCAP’s dielectric layer is composed of tantalum oxide which does not have
piezoelectric characteristics. Silence is thus assured by use of our product.
(Ceramic capacitor)
Technical data
(POSCAP)
Surface mount type
Voltage applied.
(Periodic Change.)
Subtle vibration
It generates subtle vibration by expanding and contracting
↓
The vibration travels to PCB and creates noise.
No vibration is generated.
↓
No noise on the PCB.
Radial lead type
EOL series
1-5. Allowable ripple current
Comparison of allowable ripple current
POSCAP
Line-up
（POSCAP vs Tantalum capacitor)
6.10
Tantalum capacitor (Low ESR)
Green
5.00
4.00
3.60
3.90
3.00
2.00
1.83
1.10
1.00
0.00
Series system
diagram
Image of
case size
Products list
Explanation of
part numbers
Packing
specifications
Recommended
soldering
condition
Fundamental
structure
Ｃharacteristics
Reliability
TPU
1.10
TPH
TPG
10V/150μF
6.3V/330μF
2.5V/470μF
The allowable ripple current of a capacitor is an important characterisitc when selecting
a smoothing capacitor for a power supply.
The allowable value of ripple current is decided by the generated heat of the capacitor.
This generated heat is relevant to the ESR value.
Since a large ESR capacitor generates a larger value of heat, it inhibits the ripple current value.
Because the ESR of the POSCAP is so small, it can reach a high ripple current rating
compared to other electrolytic capacitors.
TPSF
Surface mount type
Ripple Current（Arms）
6.00
POSCAP（TPE series） Blue
Technical data
7.00
Selection guide
Guidelines and
precautions
TPE
TPB
TPC
TPF
TA
TV
TH
TQC
EOL models
78
OS-CON
Line-up
Guidelines and
precautions
Ｃharacteristics
Selection guide
Technical data
1-6. ESL characteristics
POSCAP is a high performing capacitor with low ESR and large capacitance.
In recent circuit technologies for electronic equipment, the ESL value is important when
considering performance in the high frequency range.
(a) Eqivalent series circuit of capacitor
(b) Approximate ESL value of POSCAP
Surface mount type
Radial lead type
EOL series
POSCAP
Line-up
Image of
case size
Products list
Explanation of
part numbers
Packing
specifications
Recommended
soldering
condition
Fundamental
structure
Ｃharacteristics
Reliability
Technical data
Series system
diagram
Selection guide
Guidelines and
precautions
TPU
Size Code
S09
A09
A14
B1
B1S
B1G
B15
B15G
B2
B2S
at 10 MHz
0.8
1.2
1.1
1.2
0.7
1.1
1.3
1.4
1.3
0.7
Size Code
D12
D15E
D15
D2E
D2E（TPF）
D2
D3L
D3L（TPF）
D4
D4（TPF）
(unit: nH)
at 10 MHz
1.8
2.0
1.8
1.8
1.5
2.0
2.3
2.0
2.6
2.5
※Measuring method and position
： Based on JEITA RC-2002
※All values on the left figure are not
guaranteed but reference.
Please contact SANYO for details
of measurement.
1-7. Self-Healing Mechanism
Conductive polymer is used as an electrolyte in our POSCAPs. As an organic material,
conductive polymer becomes non-conductive and acts as an insulator against leakage
current at a relatively low temperature of approximately 300℃.
As seen in the explanation below, this characteristic is used to suppress leakage current
when there is microcrack in the dielectric oxide layer. We call this capability "self-healing
mechanism." In addition to this characteristic, this conductive polymer has enough heat
resistance to endure reflow soldering
Tantalum pellet
process and it is able to retain high
cross-section close-up
specific electric conductivity even
Sintered
tantalum
after going through such process.
Dielectric
oxide layer
Electrolyte
Further close-up of the layers
Initial State
Occurrence of a Microcrack
Heat Generation
Heat is generated
Electrolyte
TPH
ESL
Insulate
Polymer turns non-conductive
creating an insulated layer
TPG
Dielectric oxide layer
Surface mount type
TPSF
TPE
TPB
TPC
TPF
TA
TV
TH
TQC
EOL models
79
Sintered tantalum
The image above represents
a close-up of the cross-section of
the layers within the core of
a POSCAP,
which consists of sintered tantalum,
dielectric oxide layer and an
electrolyte (conductive polymer).
Microrack
In rare cases, a microcrack could
occur on the dielectric oxide layer
by stress caused by rapid
temperature change during the
reflow soldering process or when
excessive voltage is applied to
the capacitor.
Leakage current
Joule heat is generated locally
when leakage current flows into
the microcrack as voltage is
applied.
Conductive polymer around the
microcrack turns non-conductive
and creates an insulated layer at
a relatively-low temperature of
approximately 300℃ caused by
Joule heat. It is at this point that
the insulator suppresses the
leakage current. This is called
"self-healing mechanism" or
"self-recovery function."
With this "self-healing mechanism" POSCAP is able to minimize stress induced failures and achieve high reliability.
OS-CON
Line-up
Guidelines and
precautions
Reliability
1. Temperature accelaration test (Endurance)
The POSCAP capacitance level
decreases during a long term
endurance test.
65℃
105℃
85℃
Capacitance change
at 120Hz
6.3V/330μF
-10
( ※ Please contact SANYO for details
of TPU and TQC series. )
-15
-20
100
1,000
10,000
Time（h）
POSCAP
2,000h
105℃ ⇒
85℃ ⇒ 20,000h
65℃ ⇒ 200,000h
The left figure shows time variation of
capacitance decrease at each
temperature.
This graph indicates that temperature
coefficient of POSCAP's life time is
10 times by 20℃ reduction.※
100,000
1,000,000
Aluminum electrolytic capacitor
105℃ ⇒ 2,000h
85℃ ⇒ 8,000h
65℃ ⇒ 32,000h
※The following life time are not guaranteed but
presumptive values.
Even if POSCAP and an aluminum
electrolytic capacitor are guaranteed
on 2,000 hours at 105℃, the life
span results in big differences as
temperature drops. (See left chart)
POSCAP has a remarkably longer life
span compared with an aluminum
electrolytic capacitor.
2. Presumption of life for the POSCAP
As time increases during the endurance test, the capacitance of the POSCAP gets smaller.
This means the eventual failure mode of POSCAP is open. The POSCAP's cathode
material is made of an organic matter (conductive polymer).
The life time is different by each operating temperature and self - heating by ripple current.
The following formula outline could make it possible to estimate the presumptive lifetime
of POSCAP at ambient temperature Tx (℃).
The result of the following calculating formula estimation is not guaranteed but
presumptive value based on actual measurement.
(Please contact SANYO as to TQC series)
2-1. Calculating formula for the presumtion of life
Lx＝Lo×10
Surface mount type
To−Tx
20
Lx：Life expectance in actual use (temperature Tx) (h)
Radial lead type
EOL series
POSCAP
Line-up
Guidelines and
precautions
Selection guide
-5
Technical data
Technical data
0
Series system
diagram
Image of
case size
Products list
Explanation of
part numbers
Packing
specifications
Recommended
soldering
condition
Fundamental
structure
Ｃharacteristics
Reliability
TPU
TPH
TPG
TPSF
Surface mount type
Capacitance change（％）
5
Selection guide
TPE
TPB
TPC
TPF
TA
Lo：Guaranteed life at maximum temperature in use (h)
TV
To：Maximum operating temperature (℃)
Tx：Temperature in actual use (temperature of POSCAP) (℃)
TH
TQC
EOL models
80
OS-CON
Line-up
Surface
mount type
Guidelines and
precautions
Selection guide
TPU
Series
Specifications
Items
Technical data
Surface mount type
RoHS compliance, Halogen free
Small size, Low profile: L2.0xW1.25xH0.9mm (S09)
Condition
Rated voltage
(V)
(V)
Surge voltage
Category temperature range (℃)
Capacitance tolerance (％)
Rated capacitance range (μF)
−
−
−
120Hz/20℃
120Hz/20℃
120Hz/20℃
Dissipation Factor (DF)
Rated voltage applied, after 5 minutes
Leakage current
100kHz/20℃
Equivalent series resistance (ESR)
Characteristics of impedance
−55℃ Z/Z20℃
ratio at high temp.
100kHz/＋20℃
＋85℃ Z/Z20℃
and low temp.
△C/C
85℃, 1,000h,
Endurance
DF
rated voltage applied
LC
△C/C
60℃, 90 to 95%RH, 500h,
Damp heat (Steady State)
DF
No-applied voltage
LC
△C/C
85℃, 1,000 cycles,
Surge
DF
1kΩ discharge resistance,
surge voltage applied
LC
Specifications
2.5
2.9
4.0
6.3
10
4.6
7.2
12
−55 to ＋85
M : ±20
4.7 to 150
Please see the attached characteristics list
0.6 to 2.0
0.6 to 2.0
Within±20% of the initial value
< 1.5 times of the initial limit
ー
Within the initial limit
Within＋40%,−20% of the initial value
ー
< 3 times of the initial limit
ー
ー
Marking and dimensions
W
Anode(+)
S09size
Radial lead type
Packing
specifications
Recommended
soldering
condition
Fundamental
structure
Ｃharacteristics
Reliability
2.5 4.0 6.3
g
e
j
10
A
※2 Lot.No.shows roughly manufacturing date.
※3 The rated capacitance is as follows.(B09)
Rated voltage※1
Lot. No.※2
Capacitance(μF) 150
Mark
E8
※4 The rated capacitance is as follows.(S09)
S ±0.1※1 W1 ±0.1
0.5
0.9
0.8
2.2
R. Cap.(μF) 4.7 10
Mark
s
A
Recommended land pattern dimension of PWB
22
J
47
S
TPU
Size list
μF
(unit : mm)
b
Explanation of
part numbers
Selection guide
Products list
R.V.
Mark
68 100
W
A
※1 ±0.2:B09
Technical data
Image of
case size
E8
j F
(unit : mm)
H ±0.1
0.9
0.9
Guidelines and
precautions
Series system
diagram
Rated capacitance※3
W1
S
Size code L ±0.1※1 W ±0.1※1
S09
2.0
1.25
B09
3.5
2.8
POSCAP
Line-up
j AH
※1 The rated voltage is as follows.
B09size
Lot. No.※2
Rated voltage※1
H
S
EOL series
Anode(+)
L
a
c
a
RV
4.7
10
22
47
68
100
150
b
c
Size code a
1 0.9 0.6
S09
1.6 2.7 1.4
B09
2.5
S09
S09
RV:Rated voltage
4.0
S09
6.3
10
S09
S09
S09
S09
B09
TPU series characteristics list
TPH
TPG
Surface mount type
TPSF
TPE
TPB
TPC
TPF
TA
TV
TH
Size
code
Part number
10TPU4R7MSI
6TPU47MSI
6TPU22MSI
S09 6TPU10MSI
4TPU68MSI
ETPU100MSI
2R5TPU47MSI
B09 6TPU150MBI
※1 100k to 500kHz,45℃
TQC
EOL models
81
Maximum allowable
MSL
LC
ESR
Rated Category Category
Rated
Rated
DF
（μA）（mΩmax） ripple current Reflow Reflow
voltage temperature capacitance voltage temperature
（mArms） temp. temp.
（％ max）
max/5min. 100kHz/20℃ 100kHz※1 < 260℃ < 250℃
(℃)
（μF）
（V）
（℃）
(V)
10
6.3
6.3
6.3
4.0
2.5
2.5
6.3
85
85
85
85
85
85
85
85
4.7
47
22
10
68
100
47
150
10
6.3
6.3
6.3
4.0
2.5
2.5
6.3
85
85
85
85
85
85
85
85
10
10
10
10
10
10
10
10
4.7
59.2
27.7
6.3
54.4
50.0
23.5
94.5
300
150
150
250
150
150
150
100
360
510
510
400
510
510
510
670
ー
3
̶
̶
̶
̶
̶
̶
3
ー
3
3
3
3
3
3
3
3
Surface
mount type
TPH
Series
OS-CON
Line-up
Small size, Low profile: L3.2xW1.6xH0.9mm
Guidelines and
precautions
Specifications
Items
Selection guide
Condition
Rated voltage
(V)
−
Surge voltage
(V)
−
−
120Hz/20℃
120Hz/20℃
4.0
6.3
10
2.9
4.6
7.2
12
-55 to +105 / -55 to +85（Rated temp. 85℃）
M : ±20
Leakage current
100kHz/20℃
ratio at high temp.
and low temp.
＋85℃
0.6 to 2.0
DF
<
ー
LC
DF
<
ー
LC
Surge
Surface mount type
1.5 times of the initial limit
ー
3 times of the initial limit
<
<
△C/C
105℃, 1,000 cycles,
※Rated temp, 85℃ Products：85℃
Within＋40%,−20% of the initial value（Except for above model）
△C/C
60℃, 90 to 95%RH, 500h,
No-applied voltage
Within＋50%,−20% of the initial value（ETPH220MABC）
△C/C
0.6 to 2.0
Z/Z20℃
△C/C
105℃, 1,000h rated voltage applied
※Rated temp, 85℃ Products：
85℃, 1,000h,
Endurance
−55℃ Z/Z20℃
100kHz/＋20℃
Technical data
33 to 220
120Hz/20℃
Specifications
2.5
DF
LC
ー
jA8
Size code
A09
A14
L
3.2
3.2
W
1.6
1.6
±0.2
H
0.9
1.4
±0.1
S
0.8
0.8
±0.2
Year
Week
R.V.
Mark
W1
1.2
1.2
Capacitance(μF)
Mark
b
a
33
N7
47
S7
μF
a
b
c
Size code
1.6 1.4 1.0
A09
1.6 1.4 1.0
A14
RV
2.5
ATPH33MAHA
68
W7
10
A
POSCAP
Line-up
100
A8
150
E8
4.0
6.3
10
A09
A09
68
100
220
Guidelines and
precautions
220
J8
RV:Rated voltage
47
TPH series characteristics list
Part number
6.3
j
33
A09
A09
150
Size
code
4.0
g
Size list
(unit : mm)
c
2.5
e
※2 The rated capacitance is as follows.
±0.1
a
EOL series
Rated voltage※1
(unit : mm)
±0.2
10
09
A14,A09
A14
85
33
10
85
10
33.0
150
510
ー
3
ー
3
85
100
6.3
85
10
63.0
100
670
3
3
6.3
105
47
6.3
105
10
29.6
150
510
3
3
4TPH68MHA
4.0
105
68
4.0
105
10
27.2
150
510
3
3
ETPH100MHA
2.5
105
100
2.5
105
10
25.0
150
510
3
3
6TPH100MABC
6.3
85
100
6.3
85
10
126.0
70
740
3
3
A14 4TPH150MABC
4.0
85
150
4.0
85
10
120.0
70
740
3
3
2.5
85
220
2.5
85
10
110.0
70
740
3
3
※1 100k to 500kHz,45℃
Products list
Explanation of
part numbers
Packing
specifications
Recommended
soldering
condition
Fundamental
structure
Ｃharacteristics
Reliability
TPU
6.3
ETPH220MABC
Image of
case size
TPH
A09 6TPH47MHA
6TPH100MAEA
Series system
diagram
A14
Maximum allowable
MSL
LC
ESR
Rated
Rated
DF
（％ max）
max/5min. 100kHz/20℃ 100kHz※1 < 260℃ < 250℃
(℃)
（μF）
（V）
（℃）
(V)
10
Selection guide
H
capacitance※2
Technical data
Week
Rated voltage※1
W1
S
Rated
Year
Anode(+)
10
jA8
09
Anode(+)
W
Rated
S
Radial lead type
6TPH100MAEA
capacitance※2
TPG
TPSF
Surface mount type
L
TPE
TPB
TPC
TPF
TA
TV
TH
TQC
EOL models
82
OS-CON
Line-up
Surface
mount type
Guidelines and
precautions
Selection guide
TPG
Condition
−
2.5
4.0
6.3
8.0
10
12.5
Surge voltage
(V)
−
2.9
4.6
7.2
9.2
12
14
−
120Hz/20℃
M : ±20
120Hz/20℃
33 to 220
120Hz/20℃
100kHz/20℃
ratio at high temp.
and low temp.
100kHz/＋20℃
Ｃharacteristics
Reliability
TPU
TPH
Anode(+)
W
Size code
B1G
B15G
Surface mount type
TPSF
TPE
TPB
TPC
TPF
TA
TV
TH
TQC
EOL models
83
ー
LC
△C/C
DF
<
ー
LC
<
ー
△C/C
DF
LC
<
ー
＋0.3
W −0.1
2.8
2.8
S ±0.2
0.8
0.8
2.5
e
R.V.
Mark
c
a
W1 ±0.1
2.2
2.2
Capacitance(μF)
Mark
8.0
k
10
A
33
N7
RV
33
47
100
150
220
b
c
Size code a
1.6 2.7 1.4
B1G
1.6 2.7 1.4
B15G
47
S7
100
A8
150
E8
220
J8
Size list
μF
TPG series characteristics list
Part number
6.3
j
12.5
B
(unit : mm)
a
4.0
g
Lot. No.※2
(unit : mm)
H ±0.1
1.1
1.4
Size
code
TPG
＋0.3
L −0.1
3.5
3.5
b
Selection guide
Technical data
Fundamental
structure
<
A8
j G
Rated voltage※1
W1
S
S
Guidelines and
precautions
Recommended
soldering
condition
DF
H
POSCAP
Line-up
Packing
specifications
EOL series
Explanation of
part numbers
0.6 to 2.0
△C/C
60℃, 90 to 95%RH, 500h,
No-applied voltage
L
Products list
＋105℃ Z/Z20℃
85℃, 1,000 cycles,
Surge
0.6 to 2.0
−55℃ Z/Z20℃
85℃, 1,000h
Endurance
Image of
case size
−55 to ＋105
Series system
diagram
Specifications
(V)
Leakage current
Radial lead type
Small size, Low profile: L3.5xW2.8xH1.1mm (B1G)
Large capacitance: 6.3V220μF（B15G)
Rated voltage
Surface mount type
Series
Specifications
Items
Technical data
Update
2.5
RV:Rated voltage
4.0
6.3
B1G
B15G
B1G,B15G B15G B15G
8.0
10.0
B1G
B1G
12.5
B1G
Maximum allowable
MSL
LC
ESR
Rated
Rated
DF
（％ max）
max/5min. 100kHz/20℃ 100kHz※1 < 260℃ < 250℃
(℃)
（μF）
（V）
（℃）
(V)
12TPG33M
12.5
10TPG47M
10
8TPG47M
8.0
6.3
B1G 6TPG100M
6TPG100MG
6.3
6TPG100MZGD※2
6.3
2R5TPG220M
2.5
6TPG220MZG※2
6.3
6TPG150M
6.3
6.3
B15G 6TPG150MZG
4TPG220M
4.0
2R5TPG220MUG
2.5
85
85
85
85
85
85
85
85
85
85
85
85
※1 100k to 500kHz,45℃ ※2 Under development
33
47
47
100
100
100
220
220
150
150
220
220
10
8.0
6.4
5.0
5.0
5.0
2.0
5.0
5.0
5.0
3.2
2.0
105
105
105
105
105
105
105
105
105
105
105
105
10
10
10
10
10
10
10
10
10
10
10
10
41.3
47.0
37.6
63.0
63.0
126.0
55.0
277.2
94.5
189.0
88.0
110.0
70
70
70
70
55
35/300kHz
70
35/300kHz
70
35/300kHz
70
30/300kHz
1000
1000
1000
1000
1100
1200
1000
1200
1000
1200
1000
1400
ー
3
3
3
3
3
3
3
3
3
3
3
3
ー
3
3
3
3
3
3
3
3
3
3
3
3
TPSF
Surface
mount type
Update
Series
OS-CON
Line-up
Ultra low ESL: 0.7nH
Ultra low ESR: 6ｍΩ ＊at 500kHz
Guidelines and
precautions
Specifications
Selection guide
Items
Condition
Rated voltage
(V)
(V)
Surge voltage
Leakage current
Specifications
2.0
2.3
−
−
−
120Hz/20℃
120Hz/20℃
120Hz/20℃
100kHz/20℃
−55℃ Z/Z20℃
ratio at high temp.
100kHz/＋20℃
＋105℃ Z/Z20℃
and low temp.
105℃, 1,000h,
△C/C
Endurance
DF
※Rated temp, 85℃ Products：
85℃, 1,000h, rated voltage applied
LC
△C/C
60℃, 90 to 95%RH, 500h,
DF
No-applied voltage
LC
105℃, 1,000 cycles,
△C/C
Surge
DF
※Rated temp, 85℃ Products：85℃
LC
2.5
2.9
−55 to ＋105
M : ±20
200 to 270
Technical data
0.6 to 2.0
0.6 to 2.0
ー
ー
ー
ー
Surface mount type
L
W
Anode(+)
Rated voltage※1
R.V.
Mark
d
L8 q
H
Radial lead type
Lot. No.※2
Capacitance(μF)
Mark
W1
S
2.5
e
S
2.0
d
200
H8
EOL series
270
L8
(unit : mm)
B2S
W ±0.2
3.5
2.8
3.5
2.8
H
±0.1
1.1
1.9
S
±0.3
0.8
POSCAP
Line-up
W1 ±0.1
2.2
0.8
Guidelines and
precautions
2.2
μF
b
(unit : mm)
a
c
a
Size list
RV
RV:Rated voltage
2.0
200
a
b
c
Size code
1.6 2.7 1.4
B1S
1.6 2.7 1.4
B2S
270
Selection guide
B1S
L ±0.2
2.5
Technical data
Size code
B1S
B2S
B2S
Series system
diagram
Image of
case size
Products list
Explanation of
part numbers
Packing
specifications
Recommended
soldering
condition
Fundamental
structure
Ｃharacteristics
Reliability
TPU
TPH
TPSF series characteristics list
Part number
B1S ETPSF200M9ED※2
MSL
LC
ESR
ESL Maximum allowable
Rated Rated Rated Category Category
DF
（μA）（mΩmax）（nHmax） ripple current Reflow Reflow
（mArms）
（％ max）
temp.
max/5min. 100kHz/20℃ ＊Tipical value 100kHz※1 <temp.
(℃)
（μF）（V）
（℃）
(V)
260℃ < 250℃
ー
ー
2.5
105
200
2.5
105
8.0
100
9/500kHz
0.7
2400
2.5
105
270
2.5
105
10
135
6/500kHz
0.7
3200
3
3
B2S 2TPSF270M9G
2.0
105
270
2.0
105
8.0
108.0 9/300kHz
0.7
2400
3
3
2TPSF270M6E
2.0
105
270
2.0
105
8.0
108.0 6/500kHz
0.7
3200
5
5
ETPSF270M6E※2
5
5
TPSF
Surface mount type
Size
code
TPG
TPE
TPB
TPC
TPF
TA
TV
※1 100k∼500kHz,45℃ ※2 Under development
TH
TQC
EOL models
84
OS-CON
Line-up
TPE
Surface
mount type
Guidelines and
precautions
Selection guide
Small size: L3.5xW2.8xH1.9mm
Low ESR: 9ｍΩ ＊at 300kHz
Condition
Specifications
Rated voltage
(V)
−
2.0
2.5
4.0
6.3
8.0
10
Surge voltage
(V)
−
2.3
2.9
4.6
7.2
9.2
12
−
120Hz/20℃
M : ±20
120Hz/20℃
47 to 470
120Hz/20℃
100kHz/20℃
Leakage current
ratio at high temp.
and low temp.
Surface mount type
Series
Specifications
Items
Technical data
Update
−55 to ＋105
100kHz/＋20℃
＋105℃ Z/Z20℃
0.6 to 2.0
△C/C
105℃, 1,000h rated voltage applied
※Rated temp. 85℃ products:
Endurance
0.6 to 2.0
−55℃ Z/Z20℃
DF
60℃, 90 to 95%RH, 500h,
No-applied voltage
<
ー
△C/C
Within＋50%, −20％〈2R5TPE220MAFB(MAZB,MAPB),
2R5TPE330MAZB,2TPE330MFB(MAFB,MADGB)
ETPE330MA9GB(MAFB),2TPE470MAJGB〉
Within＋40%, −20% of the initial value (Except for the above model)
DF
<
ー
LC
Radial lead type
EOL series
Packing
specifications
Recommended
soldering
condition
Fundamental
structure
Ｃharacteristics
Reliability
W
TPU
N8
e F
TPC
TPF
TA
TV
TH
TQC
EOL models
85
ー
S
R.V.
Mark
S
2.0
d
2.5
e
4.0
g
6.3
j
8.0
k
150
E8
220
J8
10
A
Lot. No.※2
W1
Capacitance(μF) 47
Mark
S7
100
A8
120
C8
330 470
N8
S8
(unit : mm)
Size code
B2
L ±0.2
3.5
W ±0.2
2.8
H ±0.1
1.9
S ±0.2
0.8
W1 ±0.1
2.2
b
Surface mount type
TPE
<
TPH
TPB
LC
Rated voltage※1
TPG
TPSF
DF
H
Selection guide
Explanation of
part numbers
Technical data
Products list
Anode(+)
L
Guidelines and
precautions
Image of
case size
ー
POSCAP
Line-up
Series system
diagram
<
△C/C
105℃, 1,000 cycles, 1kΩ discharge
resistance,surge voltage applied
※Rated temp 85℃ products:85℃
Surge
LC
a
c
a
(unit : mm)
b
c
Size code a
1.6 2.7 1.4
B2
Size list
μF
RV
47
100
120
150
220
330
470
2.0
B2
B2
RV:Rated voltage
2.5
B2
B2
4.0
6.3
8.0
B2
B2
B2
B2
B2
B2
B2
B2
10.0
B2
OS-CON
Line-up
Guidelines and
precautions
TPE series characteristics list
Part number
10TPE47MAZB
B2
Maximum allowable
MSL
LC
ESR
Rated
Rated
DF
（mArms）
（％ max）
temp.
max/5min. 100kHz/20℃ 100kHz※1 <temp.
(℃)
（μF）
（V）
（℃）
(V)
260℃ < 250℃
10
85
47
8.0
105
8.0
47.0
35
1400
ー
3
ー
3
8TPE100MAZB
8.0
85
100
6.3
105
8.0
80.0
35
1400
3
3
6TPE220MAZB
6.3
85
220
5.0
105
10
138.6
35
1400
3
3
6TPE220MAPB※2
6.3
85
220
5.0
105
10
138.6
25
1400
3
3
5.0
105
8.0
94.5
35
6TPE150MAZB
6.3
85
150
1400
3
3
6TPE150MAPB
6.3
85
150
5.0
105
8.0
94.5
25
1600
3
3
6TPE120MAZB
6.3
85
120
5.0
105
8.0
75.6
35
1400
3
3
6TPE100MPB
6.3
105
100
6.3
105
8.0
63.0
25
1600
3
3
6TPE100MAZB
6.3
85
100
5.0
105
8.0
63.0
35
1400
3
3
4TPE220MAZB
4.0
85
220
3.2
105
8.0
88.0
35
1400
3
3
4TPE150MAZB
4.0
85
150
3.2
105
8.0
60.0
35
1400
3
3
4TPE100MZB
4.0
105
100
4.0
105
8.0
40.0
35
1400
3
3
2R5TPE330MAZB
2.5
85
330
2.0
105
8.0
82.5
35
1400
3
3
ETPE330MAFB※2
2.5
85
330
2.0
105
8.0
165.0
15
2700
3
3
ETPE330MA9GB※2
2.5
85
330
2.0
105
8.0
165.0 9/300kHz
3200
3
3
2R5TPE220MZB
2.5
105
220
2.5
105
8.0
55.0
35
1400
3
3
2R5TPE220MLB
2.5
105
220
2.5
105
8.0
55.0
21
1700
3
3
2R5TPE220MFGB
2.5
105
220
2.5
105
8.0
110.0 15/300kHz 1800
3
3
2R5TPE220MAZB
2.5
85
220
2.0
105
8.0
55.0
35
1400
3
3
2R5TPE220MAPB
2.5
85
220
2.0
105
8.0
55.0
25
1600
3
3
2R5TPE220MAFB
2.5
85
220
2.0
105
8.0
110.0
15
2000
3
3
2TPE470MAJGB
2.0
85
470
1.8
105
10
188.0 11/300kHz 2300
3
3
2TPE330MFB
2.0
105
330
2.0
105
8.0
132.0
15
2000
3
3
2TPE330MAFB
2.0
85
330
1.8
105
8.0
132.0
15
2000
3
3
2TPE330MADGB
2.0
85
330
1.8
105
8.0
132.0 13/300kHz
2000
3
3
Surface mount type
Radial lead type
EOL series
POSCAP
Line-up
Guidelines and
precautions
Technical data
Technical data
Selection guide
Size
code
Selection guide
Series system
diagram
Image of
case size
Products list
Explanation of
part numbers
Packing
specifications
Recommended
soldering
condition
Fundamental
structure
Ｃharacteristics
Reliability
TPU
TPH
TPG
Surface mount type
TPSF
TPE
TPB
TPC
TPF
TA
TV
TH
TQC
EOL models
86
OS-CON
Line-up
TPE
Surface
mount type
Guidelines and
precautions
Selection guide
Condition
Specifications
Rated voltage
(V)
−
2.5
4.0
6.3
10
Surge voltage
(V)
−
2.9
4.6
7.2
12
−
120Hz/20℃
M : ±20
120Hz/20℃
68 to 1,500
120Hz/20℃
100kHz/20℃
Leakage current
ratio at high temp.
and low temp.
Surface mount type
Low profile: 1.5ｍｍ and Large capacitance: 6.3V470μF（D15E)
Low ESR: 7ｍΩ(D2E)
Specifications
Items
Technical data
Series
−55 to ＋105
100kHz/＋20℃
＋105℃ Z/Z20℃
0.6 to 2.0
△C/C
105℃, 2,000h,
※Rated temp, 85℃ products:
6TPE330MAP,6TPE470MAZU：85℃,2,000h
Endurance
DF
<
ー
△C/C
Within＋50%, −20% of the initial value 〈2R5TPE470M (Ⅰ,F,C,9,7),
2R5TPE330M (Ⅰ,F,C,9,7), 2R5TPE220M (Ⅰ,F,9),
2R5TPE1000M (Ⅰ,F), 2R5TPE1500M (F,C)〉
DF
<
ー
LC
EOL series
L
Packing
specifications
Recommended
soldering
condition
Fundamental
structure
Ｃharacteristics
Reliability
LC
Anode(+)
W
Rated voltage※1
H
Selection guide
Explanation of
part numbers
Technical data
Products list
DF
Rated capacitance
Guidelines and
precautions
Image of
case size
<
ー
POSCAP
Line-up
Series system
diagram
ー
△C/C
105℃, 1,000 cycles,
※Rated temp. 85℃ products：85℃
Surge
<
S
R.V.
Mark
470
e 58
Radial lead type
LC
60℃, 90 to 95%RH, 500h,
No-applied voltage
0.6 to 2.0
−55℃ Z/Z20℃
Lot. No.※2
2.5
e
4.0
g
6.3
j
10
A
W1
S
(unit : mm)
Size code
D15E
D2E
D3L
D4
L ±0.3
7.3
7.3
7.3
7.3
※1 ±0.1：D2E,D15E
W ±0.2 H ±0.2※1 S ±0.2
1.1
1.4
4.3
1.3
1.8
4.3
1.3
2.8
4.3
1.3
3.8
4.3
W1 ±0.1
2.4
2.4
2.4
2.4
TPU
TPH
Surface mount type
TPSF
TPE
TPB
TPC
TPF
TA
TV
TH
TQC
EOL models
87
(unit : mm)
b
TPG
a
c
a
Size code
D15E
D2E
D3L
D4
a
2.4
2.4
2.4
2.4
b
2.9
2.9
2.9
2.9
c
3.7
3.7
3.7
3.7
Size list
μF
RV
68
100
150
220
330
470
680
1,000
1,500
2.5
D2E
D2E
D2E
D3L
D4
D4
RV:Rated voltage
4.0
6.3
D2E
D2E
D2E
D3L
D2E
D2E
D2E
D2E,D3L,D4
D4,D15E
D4
10.0
D2E
D3L
D4
OS-CON
Line-up
Guidelines and
precautions
TPE series characteristics list
10TPE68M
6TPE330MAP
6TPE220MAP
6TPE220M
6TPE220MI
6TPE150M
6TPE150MI
6TPE150MF
6TPE100M
6TPE100MI
4TPE330M
4TPE330MI
4TPE220M
4TPE220MI
4TPE220MF
D2E 4TPE150MI
2R5TPE470MI
2R5TPE470MF
2R5TPE470MC
2R5TPE470M9
2R5TPE470M7
2R5TPE330M
2R5TPE330MI
2R5TPE330MF
2R5TPE330MC
2R5TPE330M9
2R5TPE330M7
2R5TPE220M
2R5TPE220MI
2R5TPE220MF
2R5TPE220M9
10TPE220ML
10TPE220MIL
6TPE330MAL
6TPE330MA9EL
6TPE330ML
6TPE330MIL
6TPE330MFL
D3L 4TPE470ML
4TPE470MIL
4TPE470MFL
4TPE470MCL
4TPE470MAL
2R5TPE680MFL
2R5TPE680MCL
10TPE330M
6TPE680M
6TPE680MI
6TPE470M
D4
6TPE470MI
6TPE330MAA
2R5TPE1000MF
2R5TPE1500MF
2R5TPE1500MC
6.3
85
470
85
330
6.3
105
220
6.3
105
10
6.3
6.3
6.3
6.3
6.3
6.3
6.3
4.0
4.0
4.0
4.0
4.0
4.0
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
10
10
6.3
6.3
105
85
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
85
85
6.3
105
6.3
105
6.3
4.0
4.0
4.0
4.0
4.0
2.5
2.5
10
6.3
6.3
6.3
6.3
6.3
105
105
105
105
105
105
105
105
105
105
105
105
105
85
68
220
220
150
150
150
100
100
330
330
220
220
220
150
470
470
470
470
470
330
330
330
330
330
330
220
220
220
220
220
220
330
330
330
330
330
470
470
470
470
470
680
680
330
680
680
470
470
330
2.5
105
1000
2.5
105
1500
2.5
105
1500
5.0
105
10
296.1
35
1700
5.0
105
10
207.9
25
2400
10
138.6
10
5.0
6.3
6.3
6.3
6.3
6.3
6.3
6.3
4.0
4.0
4.0
4.0
4.0
4.0
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
10
10
5.0
5.0
6.3
6.3
6.3
4.0
4.0
4.0
4.0
4.0
2.5
2.5
10
6.3
6.3
6.3
6.3
5.0
2.5
2.5
2.5
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
10
10
10
10
10
10
10
10
68.0
138.6
138.6
94.5
94.5
94.5
63.0
63.0
10
132.0
10
88.0
10
10
10
10
132.0
88.0
88.0
60.0
10
117.5
10
117.5
10
10
10
10
10
10
10
10
10
10
10
10
10
117.5
117.5
117.5
25
25
25
18
25
18
15
25
18
25
18
25
18
15
18
18
15
12
9
7
82.5
25
82.5
15
82.5
82.5
82.5
82.5
18
12
9
7
55.0
25
55.0
15
55.0
55.0
18
9
10
220.0
25
10
207.9
25
10
10
10
10
10
10
10
10
10
10
10
10
10
15
15
15
15
15
15
15
15
220.0
18
207.9 9/500kHz
207.9
25
207.9
15
207.9
188.0
188.0
188.0
188.0
188.0
170.0
170.0
330.0
428.4
428.4
296.1
296.1
207.9
250.0
375.0
375.0
18
25
18
15
12
10
15
12
25
25
18
25
18
10
15
15
12
2400
2400
2400
2800
2400
2800
3100
2400
2800
2400
2800
2400
2800
3100
2800
2800
3100
3500
3900
4400
2400
2800
3100
3500
3900
4400
2400
2800
3100
3900
ー
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
2400
̶
2400
3
2800
3900
2400
2800
3100
2400
2800
3100
3500
4400
3100
3500
̶
3
3
3
3
3
3
3
3
3
3
3
3000
̶
3500
3
3000
3000
3500
4400
3900
3900
4400
3
3
3
3
3
̶
̶
ー
Selection guide
2a
2a
2a
2a
2a
Technical data
2a
2a
2a
2a
2a
2a
2a
2a
2a
Surface mount type
2a
2a
2a
2a
2a
2a
2a
2a
2a
2a
Radial lead type
2a
2a
2a
2a
EOL series
2a
2a
POSCAP
Line-up
2a
Guidelines and
precautions
2a
2a
2a
2a
2a
2a
2a
2a
2a
2a
2a
2a
Selection guide
D15E 6TPE470MAZU
Maximum allowable
MSL
LC
ESR
Rated
Rated
DF
（％ max）
max/5min. 100kHz/20℃ 100kHz※1 < 260℃ < 250℃
(℃)
（μF）
（V）
（℃）
(V)
Technical data
Part number
Series system
diagram
Image of
case size
Products list
Explanation of
part numbers
Packing
specifications
Recommended
soldering
condition
Fundamental
structure
Ｃharacteristics
Reliability
2a
TPU
2a
TPH
2a
TPG
2a
2a
2a
2a
2a
2a
2a
TPSF
Surface mount type
Size
code
TPE
TPB
TPC
TPF
TA
2a
TV
2a
TH
※1 100k to 500kHz,45℃
TQC
EOL models
88
OS-CON
Line-up
Surface
mount type
Guidelines and
precautions
Selection guide
TPB
Condition
Specifications
Rated voltage
(V)
−
4.0
Surge voltage
4.6
120Hz/20℃
M : ±20
120Hz/20℃
33 to 470
120Hz/20℃
100kHz/＋20℃
−55 to ＋105
Endurance
0.6 to 2.0
−55℃ Z/Z20℃
100kHz/20℃
＋105℃ Z/Z20℃
0.6 to 2.0
△C/C
105℃, 2,000h
B2 size :105℃, 1,000h,
Rated voltage applied
DF
60℃, 90 to 95%RH, 500h,
No-applied voltage
<
ー
△C/C
<
ー
LC
ー
LC
<
ー
Reliability
W ±0.2
2.8
4.3
4.3
※1 ±0.2：B2 ※2 ±0.1：B2
D4size
Rated capacitance
Anode(+)
Rated capacitance
330
j 58 L
Anode(+)
W
W1
S
Size code L ±0.3※1
3.5
B2
7.3
D3L
7.3
D4
W7
j G
D3Lsize
Lot. No.※2
Rated voltage※1
Lot. No.※2
Rated voltage※1
H
Selection guide
Technical data
Ｃharacteristics
S
Anode(+)
B2size
L
Guidelines and
precautions
Fundamental
structure
POSCAP
Line-up
Recommended
soldering
condition
DF
Radial lead type
Packing
specifications
<
△C/C
※Rated temp. 85℃ products:85℃
Explanation of
part numbers
LC
DF
105℃, 1,000 cycles,
1kΩdischarge resistance,
Surge
Products list
12
−
Image of
case size
7.2
−
ratio at high temp.
and low temp.
Series system
diagram
10
(V)
EOL series
6.3
Leakage current
Surface mount type
Standard products
Specifications
Items
Technical data
Series
330
A 57
R.V.
Mark
4.0 6.3
g
j
Lot. No.※2
Rated voltage※1
Capacitance(μF) 33
Mark
N7
47
S7
(unit : mm)
H ±0.2※2
1.9
2.8
3.8
S ±0.2
0.8
1.3
1.3
W1 ±0.1
2.2
2.4
2.4
TPU
TPH
Surface mount type
TPSF
TPE
TPB
TPC
TPF
TA
TV
TH
TQC
EOL models
89
(unit : mm)
b
TPG
a
c
a
b
c
Size code a
1.6 2.7 1.4
B2
2.4 2.9 3.7
D3L
2.4 2.9 3.7
D4
Size list
μF
RV
33
47
68
150
220
330
470
10
A
4.0
B2
D3L
RV:Rated voltage
6.3
B2
10.0
B2
B2
D3L
D3L D3L,D4
D4
D3L,D4
D4
68
W7
OS-CON
Line-up
Guidelines and
precautions
TPB series characteristics list
Size
code
Part number
Selection guide
Maximum allowable
MSL
LC
ESR
Rated
Rated
DF
（mArms）
（％ max）
temp.
(℃)
（μF）
（V）
（℃）
(V)
260℃ < 250℃
ー
B2
D3L
D4
ー
10TPB47M
10
105
47
10
105
8.0
47.0
70
1100
3
3
10TPB33M
10
105
33
10
105
8.0
33.0
70
1100
3
3
6TPB68M
6.3
105
68
6.3
105
8.0
42.8
70
1100
3
3
4TPB68M
4.0
105
68
4.0
105
8.0
27.2
70
1100
3
3
10TPB220ML
10
105
220
10
105
10
220.0
40
2000
̶
2a
10TPB150ML
10
105
150
10
105
10
150.0
40
2000
3
2a
6TPB330ML
6.3
105
330
6.3
105
10
207.9
40
2000
3
2a
6TPB330MAL
6.3
85
330
5.0
105
10
207.9
40
2000
3
2a
6TPB220ML
6.3
105
220
6.3
105
10
138.6
40
2000
3
2a
4TPB330ML
4.0
105
330
4.0
105
10
132.0
40
2000
3
2a
10TPB330M
10
105
330
10
105
10
330.0
35
3000
̶
2a
10TPB220M
10
105
220
10
105
10
220.0
40
3000
3
2a
6TPB470M
6.3
105
470
6.3
105
15
296.1
35
3000
3
2a
6TPB330M
6.3
105
330
6.3
105
10
207.9
40
3000
3
2a
Technical data
Surface mount type
Radial lead type
※1 100k to 500kHz,45℃
EOL series
POSCAP
Line-up
Technical data
Selection guide
Guidelines and
precautions
Series system
diagram
Image of
case size
Products list
Explanation of
part numbers
Packing
specifications
Recommended
soldering
condition
Fundamental
structure
Ｃharacteristics
Reliability
TPU
TPH
TPG
Surface mount type
TPSF
TPE
TPB
TPC
TPF
TA
TV
TH
TQC
EOL models
90
OS-CON
Line-up
TPC
Surface
mount type
Guidelines and
precautions
Selection guide
Items
Condition
(V)
−
(V)
Surge voltage
8.0
7.2
−
Specifications
6.3
−
120Hz/20℃
100kHz/＋20℃
ratio at high temp.
and low temp.
−55℃ Z/Z20℃
100kHz/20℃
＋105℃ Z/Z20℃
105℃, 2,000h
B2 size :105℃, 1,000h,
Endurance
△C/C
DF
Surge
0.6 to 2.0
0.6 to 2.0
DF
<
ー
LC
ー
<
<
△C/C
DF
LC
※Rated temp. 85℃ products:85℃
ー
△C/C
105℃, 1,000 cycles,
1kΩdischarge resistance,
<
LC
60℃, 90 to 95%RH, 500h,
No-applied voltage
14
M : ±20
12.5
10 to 470
120Hz/20℃
Leakage current
10
9.2
12
−55 to ＋105
120Hz/20℃
Surface mount type
Low profile: 1.1mm (B1)
Specifications
Rated voltage
Technical data
Series
ー
Anode(+)
W
H
Radial lead type
S
EOL series
POSCAP
Line-up
Explanation of
part numbers
Packing
specifications
Recommended
soldering
condition
Fundamental
structure
Ｃharacteristics
Reliability
TPU
TPH
TPG
Surface mount type
TPSF
TPE
TPB
TPC
TPF
TA
TV
TH
TQC
EOL models
91
Rated capacitance
150
j 57
Lot. No.※2
Rated voltage※1
(unit : mm)
W
2.8
4.3
±0.2
H
1.1
1.9
±0.1
S
0.8
1.3
±0.2
W1
2.2
2.4
±0.1
(unit : mm)
b
Selection guide
Products list
Technical data
Image of
case size
L
3.5
7.3
Lot. No.※2
Rated voltage※1
W1
S
±0.2
S7
j G
R.V.
Mark
a
c
a
b
c
Size code a
1.6 2.7 1.4
B1
2.4 2.9 3.7
D2
6.3 8.0
j
k
10 12.5
A
B
Capacitance(μF) 10
Mark
A7
Guidelines and
precautions
Series system
diagram
Size code
B1
D2
D2size
Anode(+)
B1size
L
15
E7
22
J7
Size list
μF
RV
10
15
22
33
47
68
100
150
330
6.3
B1
B1
D2
D2
D2
33
N7
47
S7
RV:Rated voltage
8.0
B1
D2
10.0
12.5
B1
B1
B1
D2
D2
OS-CON
Line-up
Guidelines and
precautions
TPC series characteristics list
Size
code
Part number
Selection guide
Maximum allowable
MSL
LC
ESR
Rated
Rated
DF
（mArms）
（％ max）
temp.
(℃)
（μF）
（℃）
（V）
(V)
260℃ < 250℃
ー
12.5
85
15
10
105
10
18.8
80
800
3
3
12TPC10M
12.5
85
10
10
105
10
12.5
80
800
3
3
8.0
85
22
6.3
105
10
17.6
70
1000
3
3
6TPC47MB
6.3
85
47
5.0
105
10
29.6
70
1000
3
3
6TPC47M
6.3
85
47
5.0
105
10
29.6
55
1100
3
3
B1 8TPC22M
D2
ー
12TPC15M
10TPC100M
10
105
100
10
105
10
100.0
45
1700
3
2a
10TPC68M
10
105
68
10
105
10
68.0
45
1700
3
2a
8TPC150M
8.0
105
150
8.0
105
10
120.0
40
1900
3
2a
6TPC330MA
6.3
85
330
5.0
105
10
207.9
40
1900
3
2a
6TPC150M
6.3
105
150
6.3
105
10
94.5
40
1900
3
2a
6TPC100M
6.3
105
100
6.3
105
10
63.0
45
1700
3
2a
Technical data
Surface mount type
※1 100k∼500kHz,45℃
Radial lead type
EOL series
POSCAP
Line-up
Technical data
Selection guide
Guidelines and
precautions
Series system
diagram
Image of
case size
Products list
Explanation of
part numbers
Packing
specifications
Recommended
soldering
condition
Fundamental
structure
Ｃharacteristics
Reliability
TPU
TPH
TPG
Surface mount type
TPSF
TPE
TPB
TPC
TPF
TA
TV
TH
TQC
EOL models
92
OS-CON
Line-up
TPF
Surface
mount type
Guidelines and
precautions
Selection guide
Ultra low ESR: 5ｍΩ∼15mΩ
Large capacitance: 1,000μF
Condition
Specifications
Rated voltage
(V)
−
2.0
2.5
4.0
6.3
10
Surge voltage
(V)
−
2.3
2.9
4.6
7.2
12
−
120Hz/20℃
M : ±20
120Hz/20℃
150 to 1000
Leakage current
−55 to ＋105
120Hz/20℃
100kHz/20℃
ratio at high temp.
and low temp.
Surface mount type
Series
Specifications
Items
Technical data
Update
100kHz/＋20℃
＋105℃ Z/Z20℃
0.6 to 2.0
△C/C
105℃, 2,000h,
Endurance
0.6 to 2.0
−55℃ Z/Z20℃
DF
ー
LC
△C/C
60℃, 90 to 95%RH, 500h,
No-applied voltage
Within＋50%,−20% of the initial value(2TPF220M6,2TPF330M6,ETPF1000M6H（5H）)
DF
ー
<
ー
△C/C
105℃, 1,000 cycles,
<
LC
Surge
<
DF
LC
<
ー
Radial lead type
L
W
Anode(+)
Rated capacitance
POSCAP
Line-up
Products list
Explanation of
part numbers
Packing
specifications
Recommended
soldering
condition
Fundamental
structure
Ｃharacteristics
Reliability
Selection guide
Image of
case size
Technical data
Series system
diagram
Rated voltage※1
H
Guidelines and
precautions
S
※1 ±0.1:D2E
L ±0.3
7.3
7.3
7.3
W ±0.2 H ±0.2※1 S ±0.2
1.3
1.8
4.3
1.3
2.8
4.3
1.3
3.8
4.3
b
Surface mount type
TPF
TA
TV
TH
TQC
EOL models
93
6.3
j
10
A
W1 ±0.1
2.4
2.4
2.4
TPG
TPC
4.0
g
Lot. No.※2
(unit : mm)
TPB
2.5
e
(unit : mm)
Size code
D2E
D3L
D4
TPU
TPE
2.0
d
W1
S
TPH
TPSF
R.V.
Mark
470
e 58 F
EOL series
a
c
a
b
c
Size code a
2.4 2.9 3.7
D2E
2.4 2.9 3.7
D3L
2.4 2.9 3.7
D4
Size list
μF
RV
2.0
RV:Rated voltage
2.5
4.0
6.3
150
D3L
220
D2E
330
D2E
D3L
D3L
D3L
D3L
470
D4,D3L
D3L
D4
680
D4,D3L
D4
1,000
10.0
D4
OS-CON
Line-up
Guidelines and
precautions
TPF series characteristics list
Part number
Maximum allowable
MSL
LC
ESR
Rated
Rated
DF
（mArms）
（％ max）
temp.
(℃)
（μF）
（V）
（℃）
(V)
260℃ < 250℃
ー
D2E
ー
2TPF330M6
2.0
105
330
2.0
105
10
132.0
6
4700
̶
2a
2TPF220M6
2.0
105
220
2.0
105
10
88.0
6
4700
̶
2a
105
150
105
10
150.0
15
3600
̶
2a
105
330
105
10
207.9
9
3900
3
2a
10TPF150ML
6TPF330M9L
10
6.3
10
6.3
6TPF330M5EL※2
6.3
105
330
6.3
105
10
207.9 5/500kHz 6200
3
2a
6TPF220ML
6.3
105
220
6.3
105
10
138.6
12
4000
3
2a
6TPF220M9L
6.3
105
220
6.3
105
10
138.6
9
4600
3
2a
6TPF220M5L
6.3
105
220
6.3
105
10
138.6
5
6100
3
2a
4TPF470ML
4.0
105
470
4.0
105
10
188.0
10
4400
3
2a
D3L 4TPF470M5EL※2
4.0
105
470
4.0
105
10
188.0 5/500kHz 6200
3
2a
4TPF330ML
4.0
105
330
4.0
105
10
132.0
12
4000
3
2a
2R5TPF680ML
2.5
105
680
2.5
105
10
170.0
10
4400
3
2a
2R5TPF680M7L
2.5
105
680
2.5
105
10
170.0
7
4400
3
2a
2R5TPF680M6L
2.5
105
680
2.5
105
10
170.0
6
4400
3
2a
2R5TPF470ML
2.5
105
470
2.5
105
10
117.5
10
4400
3
2a
2R5TPF470M7L
2.5
105
470
2.5
105
10
117.5
7
4400
3
2a
2R5TPF470M6L
2.5
105
470
2.5
105
10
117.5
6
4400
3
2a
2R5TPF330M7L
2.5
105
330
2.5
105
10
82.5
7
4400
3
2a
6TPF470MAH
6.3
105
470
6.3
105
10
296.1
10
4400
3
2a
4TPF680MAH
4.0
105
680
4.0
105
10
272.0
10
4400
3
2a
ETPF1000M6H
2.5
105
1000
2.5
105
10
250.0
6
5600
3
2a
ETPF1000M5H
2.5
105
1000
2.5
105
10
250.0
5
6100
3
2a
ETPF680M5H
2.5
105
680
2.5
105
10
170.0
5
6100
3
2a
ETPF470M5H
2.5
105
470
2.5
105
10
117.5
5
6100
3
2a
D4
Surface mount type
Radial lead type
EOL series
POSCAP
Line-up
Guidelines and
precautions
Technical data
Technical data
Selection guide
Size
code
Selection guide
Series system
diagram
Image of
case size
Products list
Explanation of
part numbers
Packing
specifications
Recommended
soldering
condition
Fundamental
structure
Ｃharacteristics
Reliability
TPU
TPH
TPG
Surface mount type
TPSF
TPE
TPB
TPC
TPF
TA
TV
TH
TQC
EOL models
94
OS-CON
Line-up
Surface
mount type
Guidelines and
precautions
Selection guide
TA
Series
Specifications
Items
Technical data
Surface mount type
High reliability: 85℃85%RH rated voltage applied (warranty)
Power supply circuit of entertainment equipment for the car.
Condition
Rated voltage
(V)
Surge voltage
(V)
Category temperature range(℃)
Leakage current
−
−
−
120Hz/20℃
120Hz/20℃
120Hz/20℃
100kHz/20℃
−55℃ Z/Z20℃
100kHz/＋20℃
ratio at high temp. and low temp.
＋105℃ Z/Z20℃
△C/C
105℃, 2,000h,
Endurance
(B2 size : 1,000h)
DF
LC
△C/C
85℃,
85
to
90%RH,
500h,
Damp heat(Load)
DF
LC
△C/C
105℃, 1,000 cycles,
Surge
DF
LC
Specifications
2.5
2.9
4.0
6.3
10
4.6
7.2
12
−55 to ＋105
M : ±20
47 to 680
0.6 to 2.0
0.6 to 2.0
ー
Within＋40%,−20% of the initial value ※1
ー
ー
※1 Within ＋50%, −20% of the initial value(2R5TAE470M(F), 2R5TAE330M(F, I), 2R5TAE220M(F,9))
B2size
D2E,D3Lsize
EOL series
S
B2
3.5
D2E
7.3
D3L
7.3
W ±0.2
2.8
4.3
4.3
※1 ±0.1:D2E,B2 ※2 ±0.2:B2
H ±0.2※1
1.9
1.8
2.8
Explanation of
part numbers
Packing
specifications
Recommended
soldering
condition
Fundamental
structure
Ｃharacteristics
Reliability
b
Selection guide
Products list
Technical data
Image of
case size
TPU
TPH
TPG
Surface mount type
TPSF
TPE
TPB
TPC
TPF
TA
TV
TH
TQC
EOL models
95
W1 ±0.1
2.2
2.4
2.4
a
c
a
μF
b
c
Size code a
1.6 2.7 1.4
B2
2.4 2.9 3.7
D2E
2.4 2.9 3.7
D3L
Size
code
Part number
10TAB47M
6TAB68M
B2
6TAB47M
4TAB100M
10TAE68M
6TAE220M
6TAE220MI
6TAE150M
4TAE220M
4TAE220MI
D2E 2R5TAE470M
2R5TAE470MF
2R5TAE330M
2R5TAE330MI
2R5TAE330MF
2R5TAE220M
2R5TAE220MF
2R5TAE220M9
10TAE220ML
10TAE150ML
6TAE330ML
D3L 4TAE470ML
4TAE470MIL
2R5TAE680ML
2R5TAE680MFL
※1 100k to 500kHz,45℃
RV
47
68
100
150
220
330
470
680
TA series characteristics list
10
A
Capacitance(μF)
Mark
47
S7
68 100
W7 A8
Size list
(unit : mm)
Guidelines and
precautions
Series system
diagram
S ±0.2
0.8
1.3
1.3
2.5 4.0 6.3
g
e
j
(unit : mm)
POSCAP
Line-up
R.V.
Mark
Lot. No.※2
Rated voltage※1
Lot. No.※2
Rated voltage※1
W1
S
Anode(+)
Anode(+)
W
H
Radial lead type
S7
j G
Rated capacitance
470
e 58
L
2.5
RV:Rated voltage
4.0
B2
D2E
D2E
D2E
D3L
D2E
D3L
6.3
10.0
B2
B2
B2
D2E
D2E
D2E
D3L
D3L
D3L
Maximum allowable
MSL
LC
ESR
Rated
Rated
DF
（mArms）
（％ max）
temp.
(℃)
（μF）
（℃）
（V）
(V)
260℃ < 250℃
10
6.3
6.3
4.0
10
6.3
6.3
6.3
4.0
4.0
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
10
10
6.3
4.0
4.0
2.5
2.5
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
47
68
47
100
68
220
220
150
220
220
470
470
330
330
330
220
220
220
220
150
330
470
470
680
680
10
6.3
6.3
4.0
10
6.3
6.3
6.3
4.0
4.0
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
10
10
6.3
4.0
4.0
2.5
2.5
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
8.0
8.0
8.0
8.0
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
47.0
42.8
29.6
40.0
68.0
138.6
138.6
94.5
88.0
88.0
117.5
117.5
82.5
82.5
82.5
55.0
55.0
110.0
220.0
150.0
207.9
188.0
188.0
170.0
170.0
70
70
70
70
25
25
18
25
25
18
25
15
25
18
15
25
15
9
25
25
25
25
18
25
15
1100
1100
1100
1100
2400
2400
2800
2400
2400
2800
2400
3100
2400
2800
3100
2400
3100
3900
2400
2400
2400
2400
2800
2400
3100
ー
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
ー
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
Surface
mount type
TV
OS-CON
Line-up
High reliability: 85℃85%RH rated voltage applied (warranty)
higher thermal resistance: 125℃ guaranteed（ambient temperature）
Power supply circuit of entertainment equipment for the car.
Series
Specifications
Guidelines and
precautions
Selection guide
Items
Condition
Rated voltage
(V)
Surge voltage
(V)
Category temperature range(℃)
Leakage current
Specifications
−
6.3
10
−
7.2
12
−55 to ＋125
−
M : ±20
120Hz/20℃
68 to 150
120Hz/20℃
120Hz/20℃
100kHz/20℃
0.6 to 2.0
−55℃ Z/Z20℃
100kHz/＋20℃
ratio at high temp. and low temp.
＋105℃ Z/Z20℃
0.6 to 2.0
105
125
temp
125℃, 1,000h,
Within±20% of the initial value Within±20% of the initial value
△C/C
Endurance
category voltage applied
< 2 times of the initial limit < 1.5 times of the initial limit
DF
ー
ー
（105℃ 2,000h, rated voltage applied）
LC
ー
△C/C
85℃,
85
to
90%RH,
500h,
Damp heat(Load)
DF
ー
LC
Within±5%
of the initial value
△C/C
105℃, 1,000 cycles,
Surge
DF
LC
ー
Technical data
Surface mount type
L
150
j 58
Lot.
68
W7
Capacitance(μF)
Mark
(unit : mm)
W ±0.2 H ±0.2※1 S ±0.2 W1 ±0.1
4.3
1.8
1.3
2.4
4.3
2.8
1.3
2.4
150
E8
EOL series
POSCAP
Line-up
Size list
μF
a
a
b
c
Size code
2.4 2.9 3.7
D2E
2.4 2.9 3.7
D3L
RV
6.3
68
150
Guidelines and
precautions
RV:Rated voltage
10.0
D2E
D2E
D3L
Technical data
b
(unit : mm)
c
Radial lead type
a
10
A
Selection guide
※1 ±0.1:D2E
L ±0.3
7.3
7.3
6.3
j
No.※2
Rated voltage※1
W1
S
Size code
D2E
D3L
R.V.
Mark
TV series characteristics list
Size
code
Part number
D2E
6TVE150M
D3L 10TVE150ML
※1 100k to 500kHz,45℃
Image of
case size
Products list
Explanation of
part numbers
Packing
specifications
Recommended
soldering
condition
Fundamental
structure
Ｃharacteristics
Reliability
Maximum allowable
MSL
LC
ESR
Rated
Rated
DF
（mArms）
（％ max）
temp.
(℃)
（μF）
（V）
（℃）
(V)
260℃ < 250℃
ー
10TVE68M
Series system
diagram
10
6.3
10
ー
105
68
6.3
125
10
68.0
25
2400
5
3
105
150
4.0
125
10
94.5
25
2400
5
3
105
150
6.3
125
10
150.0
25
2400
TPU
TPH
5
3
TPG
TPSF
Surface mount type
S
Rated capacitance
H
Anode(+)
W
D2E,D3Lsize
TPE
TPB
TPC
TPF
TA
TV
TH
TQC
EOL models
96
Surface
mount type
Guidelines and
precautions
Selection guide
TH
Condition
Series
6.3
10
2.5
6.3
10
2.5
4.0
6.3
Surge voltage
(V)
−
4.6
7.2
12
2.9
7.2
12
2.9
4.6
7.2
−
120Hz/20℃
120Hz/20℃
100kHz/＋20℃
Fundamental
structure
Ｃharacteristics
Reliability
＋125℃ Z/Z20℃
0.6 to 2.0
△C/C
<
ー
LC
<
ー
60℃, 90 to 95%RH,
500h,
No-applied voltage
DF
<
ー
LC
ー
△C/C
105℃, 1,000 cycles,
1kΩ discharge
resistance,
<
DF
LC
<
ー
D2E,D3L size
D2,D4 size
220
j 58 L
Anode(+)
W
L
D3L size
Rated voltage※1
Rated capacitance
330
j 57
Lot. No.※2
Rated voltage※1
R.V.
Mark
2.5 4.0 6.3
g
e
j
10
A
Lot. No.※2
H
Selection guide
DF
△C/C
Rated capacitance
Technical data
Recommended
soldering
condition
0.6 to 2.0
−55℃ Z/Z20℃
125℃, 1,000h,
category voltage
applied
Guidelines and
precautions
Packing
specifications
150 to 330
100kHz/20℃
L
Explanation of
part numbers
68 to 220
ratio at high temp.
and low temp.
Surge
M : ±20
220 to 470
120Hz/20℃
POSCAP
Line-up
Products list
−55 to ＋125
Image of
case size
THE
4.0
Endurance
Series system
diagram
THC
−
EOL series
THB
−
(V)
Leakage current
Radial lead type
Specifications
Rated voltage
Surface mount type
higher thermal resistance: 125℃ guaranteed（ambient temperature）
For the Industrial equipment
Specifications
Items
Technical data
Series
Anode(+)
OS-CON
Line-up
S
S
D2E
7.3
D2
7.3
D3L
7.3
D4
7.3
W1
(unit : mm)
W ±0.2 H ±0.1※2 S ±0.2
1.3
1.8
4.3
1.3
1.9
4.3
1.3
2.8
4.3
1.3
3.8
4.3
※1 ±0.2:D2 ※2 ±0.2:D3L,D4
W1 ±0.1
2.4
2.4
2.4
2.4
TPU
TPH
Surface mount type
TPSF
TPE
TPB
TPC
TPF
TA
(unit : mm)
b
TPG
a
c
a
Size code
D2E
D2
D3L
D4
a
2.4
2.4
2.4
2.4
b
2.9
2.9
2.9
2.9
c
3.7
3.7
3.7
3.7
Size list
μF
68
150
Series
RV:Rated voltage
RV
2.5
220
D2
THE
D2E
THC
TQC
470
EOL models
97
THB
D3L
D4
D4
D4
D2
D2E
THB
THE
10.0
D2
THC
THE
330
6.3
THC
THB
TV
TH
4.0
D3L
D2E
D4
OS-CON
Line-up
Guidelines and
precautions
TH series characteristics list
Series
Size
code
Part number
Selection guide
Maximum allowable
MSL
LC
ESR
Rated Rated Rated Category Category
DF
（mArms）
（％ max）
temp.
(℃)
（μF）（V）
（℃）
(V)
260℃ < 250℃
ー
D3L
THB
D4
6.3
105
220
4.0
125
10
138.6
40
2000
̶
5
4THB330ML
4.0
105
330
2.5
125
10
132.0
40
2000
̶
5
10THB330M
10
105
330
6.3
125
10
330.0
35
3000
̶
5
10THB220M
10
105
220
6.3
125
10
220.0
40
3000
̶
5
6THB470M
6.3
105
470
4.0
125
15
296.1
35
3000
̶
5
6THB330M
6.3
105
330
4.0
125
10
207.9
40
3000
̶
5
105
68
6.3
125
10
68.0
45
1700
̶
5
6.3
105
150
4.0
125
10
94.5
40
1900
̶
5
2R5THC220M
2.5
105
220
1.6
125
10
55.0
45
1700
̶
5
6THE150M
6.3
105
150
4.0
125
10
94.5
25
2400
̶
5
6THE150MI
6.3
105
150
4.0
125
10
94.5
18
2800
̶
5
4THE220M
4.0
105
220
2.5
125
10
88.0
25
2400
̶
5
4THE220MI
4.0
105
220
2.5
125
10
88.0
18
2800
̶
5
4THE220MF
4.0
105
220
2.5
125
10
88.0
15
3100
̶
5
2R5THE330M
2.5
105
330
1.6
125
10
82.5
25
2400
̶
5
2R5THE330MI
2.5
105
330
1.6
125
10
82.5
18
2800
̶
5
2R5THE330MF
2.5
105
330
1.6
125
10
82.5
15
3100
̶
5
10THC68M
THC D2 6THC150M
THE D2E
ー
6THB220ML
10
Technical data
Surface mount type
Radial lead type
EOL series
※1 100k to 500kHz,45℃
POSCAP
Line-up
Technical data
Selection guide
Guidelines and
precautions
Series system
diagram
Image of
case size
Products list
Explanation of
part numbers
Packing
specifications
Recommended
soldering
condition
Fundamental
structure
Ｃharacteristics
Reliability
TPU
TPH
TPG
Surface mount type
TPSF
TPE
TPB
TPC
TPF
TA
TV
TH
TQC
EOL models
98
OS-CON
Line-up
TQC
Surface
mount type
Guidelines and
precautions
Selection guide
Series
Condition
Specifications
Rated voltage
(V)
−
16
20
25
35
Surge voltage
(V)
−
20
23
29
40
−
−55 to ＋105
(％)
120Hz/20℃
M : ±20
120Hz/20℃
2.7 to 150
120Hz/20℃
100kHz/20℃
Capacitance tolerance
Leakage current
ratio at high temp.
and low temp.
−55℃ Z/Z20℃
100kHz/＋20℃
Surface mount type
0.6 to 1.0
△C/C
Within ±20% of the initial value
DF
Within 1.5 times of the initial limit
LC
△C/C
Within ＋40%,−20% of the initial value
DF
Within 1.5 times of the initial limit
LC
Within 3 times of the initial limit
△C/C
Within ±5% of the initial value
DF
LC
Within 3 times of the initial limit
60℃, 90 to 95%RH, 500h,
No-applied voltage
15 to 35℃, 1,000 cycies,
Surge
Radial lead type
Packing
specifications
Recommended
soldering
condition
Fundamental
structure
Ｃharacteristics
Reliability
Anode(+)
W
Selection guide
Explanation of
part numbers
Technical data
Products list
S
S
B15
3.5
B2
3.5
D12
7.3
D15
7.3
D2
7.3
D3L
7.3
S7
j G
W1
W ±0.2
2.8
2.8
4.3
4.3
4.3
4.3
Rated capacitance
680
e 57
Lot. No.※2
Rated voltage※1
Lot. No.※2
Rated voltage※1
H
Guidelines and
precautions
Image of
case size
D12，D15,D2,D3L size
Anode(+)
B2 size
L
POSCAP
Line-up
Series system
diagram
1.0 to 2.0
＋105℃ Z/Z20℃
105℃, 2,000h
Endurance
EOL series
RoHS directive/Halogen-free compliant
High voltage（35V）
Specifications
Items
Technical data
Update
R.V.
Mark
16
C
20 25 35
D 1E（orE） V
Capacitance(μF) 2.7 3.9 5.6 8.2 10 15 22 33 47 68 100 150
Mark L6 Q6 U6 Y6 A7 E7 J7 N7 S7 W7 A8 E8
(unit : mm)
H ±0.1※2
※3
1.4
1.9
1.15
1.4
1.9
2.8
※1 ±0.3:D3L ※2 ±0.2:D3L ※3 ±0.05:D12
S ±0.2
0.8
0.8
1.3
1.3
1.3
1.3
W1 ±0.1
2.2
2.2
2.4
2.4
2.4
2.4
TPU
TPH
TPG
Surface mount type
TPE
TPB
TPC
TPF
TA
TV
TH
TQC
EOL models
99
b
(unit : mm)
TPSF
a
c
a
Size code
B15
B2
D12
D15
D2
D3L
a
1.6
1.6
2.4
2.4
2.4
2.4
b
2.7
2.7
2.9
2.9
2.9
2.9
c
1.4
1.4
3.7
3.7
3.7
3.7
Size list
μF
RV
2.7
3.9
5.6
8.2
10
15
22
33
47
68
100
150
16
B2
B2
D12,D2
D15,D2
D2
D2
D3L
RV:Rated voltage
20
B2
B2,D2
D2
D15,D2
D3L
25
B2
B2,D2
D15,D2
D2
35
B15
B2
D2
OS-CON
Line-up
Guidelines and
precautions
TQC series characteristics list
Maximum allowable
MSL
LC
ESR
Rated
Rated
DF
（mArms）
（％ max）
temp.
(℃)
（μF）
（V）
（℃）
(V)
260℃ < 250℃
ー
ー
B15 35TQC2R7MYF
35
105
2.7
35
105
10
47.3
300
800
̶
3
35TQC3R9MYF
35
105
3.9
35
105
10
40.9
400
500
̶
3
25TQC15MYFB
25
105
25
105
10
112.5
100
900
̶
3
B2 25TQC5R6M
25
105
25
105
10
42.0
100
800
̶
3
20TQC22MYFB
20
105
20
105
10
132.0
90
1000
̶
3
20TQC8R2M
20
105
20
105
10
49.2
100
800
̶
3
16TQC15M
16
105
15
16
105
10
72.0
90
1000
̶
3
16TQC10M
16
105
10
16
105
10
48.0
100
800
̶
3
D12 16TQC33MYFS
16
105
33
16
105
10
52.8
40
1800
̶
3
25TQC22MYFT
25
105
22
25
105
10
55.0
70
1400
̶
3
D15 20TQC47MYFT
20
105
47
20
105
10
94.0
55
1500
̶
3
16TQC47MYFT
16
105
47
16
105
10
75.2
55
1500
̶
3
35TQC10M
35
105
10
35
105
10
35.0
120
1000
̶
3
25TQC33MYF
25
105
33
25
105
10
82.5
60
1400
̶
3
25TQC22MV
25
105
22
25
105
10
55.0
45
1500※2
̶
3
25TQC22MYFD
25
105
22
25
105
10
55.0
60
1400
25TQC15MV
25
105
15
25
105
10
38.0
45
25TQC15MYFD
25
105
15
25
105
10
38.0
20TQC47MYF
20
105
47
20
105
10
20TQC33MYFD
20
105
33
20
105
20TQC22MYFD
20
105
22
20
16TQC100MYF
16
105
100
16TQC68MYF
16
105
16TQC47MW
16
16TQC47MYFD
D2
D3L
15
5.6
22
8.2
̶
3
1500
※2
̶
3
90
1000
※2
̶
3
94.0
55
1450
̶
3
10
66.0
60
1400
̶
3
105
10
44.0
80
1300
̶
3
16
105
10
160.0
50
1800
̶
3
68
16
105
10
108.8
50
1500
̶
3
105
47
16
105
10
75.2
40
1800
̶
3
16
105
47
16
105
10
75.2
55
1450
̶
3
16TQC33MYFD
16
105
33
16
105
10
52.8
70
1400
̶
3
20TQC100MYF
20
105
100
20
105
10
200.0
55
1700
̶
3
16TQC150MYF
16
105
150
16
105
10
240.0
50
1800
̶
3
Technical data
Surface mount type
Radial lead type
EOL series
POSCAP
Line-up
Guidelines and
precautions
Selection guide
Part number
Technical data
Size
code
Selection guide
Series system
diagram
Image of
case size
Products list
Explanation of
part numbers
Packing
specifications
Recommended
soldering
condition
Fundamental
structure
Ｃharacteristics
Reliability
TPU
TPH
※1 100k∼500kHz,105℃ ※2 100k∼300kHz,105℃
TPG
Surface mount type
TPSF
TPE
TPB
TPC
TPF
TA
TV
TH
TQC
EOL models
100
Catalog Deletion and EOL Models
OS-CON
Line-up
Guidelines and
precautions
Selection guide
Catalog Deletion and EOL Models
Technical data
●Catalog Deletion Models
The following table is a list of our items which have been deleted from our catalogs.
If you are using any of the following models on the deleted list,
please substitute them with the suggested alternative model as soon as possible.
Our company continue to supply them to customers who have already used them, for the time being.
Series
Size
code
Models for
deletion
Year of
deletion
Alternative model
2R5TPE680MFL
2R5TPE680MFL
4TPE680M
2011
6TPE680MI
4TPE680MI
2012
6TPE680MI
4TPE680MF
2012
4TPF680MAH
2R5TPE220MZB
2R5TPE1000M
2011
2R5TPE1000MF
2012
4TPE100MZB
2R5TPE1000MI
2012
2R5TPE1000MF
10TPB100ML
2010
10TPC100M
10TPG33M
2011
10TPC33MB
6TPB150ML
2009
6TPC150M
D12T
All models
2013
-
4TPB470ML
2009
4TPE470ML
D15T
All models
2013
-
4TPB220ML
2009
4TPE220M
D2T
All models
2013
-
2R5TPB330ML
2009
2R5TPE330M
TPLF
D2T
All models
2013
-
10TPB100M
2008
10TPC100M
TPSF
B2S
11TPSF62MAIG
2012
-
6TPB150M
2008
6TPC150M
TPH
A14
ETPH220MAZC
2013
-
4TPB220M
2008
4TPE220M
2R5TPU22MSI
2011
6TPU22MSI
4TPB680M
2009
6TPE680MI
4TPU15MSI
2011
6TPU22MSI
4TPB470M
2009
4TPE470ML
4TPU33MSI
2011
6TPU47MSI
2R5TPB1000M
2009
2R5TPE1000MF
6TPU33MSK
2013
6TPU47MSI
2R5TPB680M
2009
2R5TPE680MFL
4TPU47MSK
2013
6TPU47MSI
10TPC33MB
2013
12TPG33M
2R5TPU68MSK
2013
4TPU68MSI
6TPC33M
2012
6TPC47MB
10TPU33MAI
2011
ATPH33MAHA
4TPC47M
2012
6TPC47MB
6TPU47MAI
2011
6TPH47MHA
2R5TPC56M
2012
6TPB68M
4TPU68MAI
2011
4TPH68MHA
4TPC220M
2009
4TPE220M
2R5TPU100MAI
2011
ETPH100MHA
4TPC150M
2009
4TPE150MI
4THC220M
2013
4THE220M
2R5TPC330M
2009
2R5TPE330M
10THB100ML
2010
-
6TPE100MZB
2011
6TPE100MPB
2R5THB330ML
2010
-
4TPE150MUB
2013
4TPE150MAZB
4THB680M
2013
-
2R5TPE220MIB
2012
2R5TPE220MFGB
25TQC10M
2011
25TQC15MYFD
2R5TPE220MDGB
2013
2R5TPE220MFGB
20TQC15M
2011
25TQC15MYFD
2R5TPE150MZB
2011
2R5TPE220MZB
16TQC22M
2011
20TQC22MYFD
2TPE330MIB
2011
2TPE330MFB
25TQC15M
2012
25TQC15MYFD
2TPE330MAFGB
2011
2TPE330MAFB
25TQC22M
2012
25TQC22MYFD
4TPE150M
2011
4TPE150MI
20TQC22M
2012
20TQC22MYFD
2R5TPE470M
2011
2R5TPE470MI
20TQC47MY
2012
20TQC47MYF
TPH
2TPE470M9
2011
2R5TPE470M9
16TQC33M
2012
16TQC33MYFD
TPG
2TPE470M7
2011
2R5TPE470M7
16TQC47M
2012
16TQC47MYFD
2TPE470M6
2011
2R5TPF470M6L
16TQC68MY
2012
16TQC68MYF
2TPE330M9
2011
2R5TPE330M9
25TQC33M
2012
25TQC33MYF
2TPE330M7
2011
2R5TPE330M7
20TQC47M
2012
20TQC47MYF
2TPE330M6
2011
2TPF330M6
16TQC68M
2012
16TQC68MYF
2R5TPE220MC
2012
2R5TPE220M9
16TQC100M
2012
16TQC100MYF
2R5TPE220M7
2012
2R5TPE330M7
Radial lead type
D3
EOL series
D4
POSCAP
Line-up
Guidelines and
precautions
Products list
Explanation of
part numbers
Packing
specifications
Recommended
soldering
condition
Fundamental
structure
Ｃharacteristics
Reliability
Selection guide
Image of
case size
TPC
D2
Technical data
Series system
diagram
B1
B2
TPU
Surface mount type
TPSF
TPE
TPB
TPC
TPF
TA
TV
TH
TQC
EOL models
101
TPE
D2E
6TPB100MAV
2009
6TPE100MAZB
6TPB47M
2009
6TPC47MB
4TPB100M
2009
4TPE100MZB
2R5TPB220MA
2009
2R5TPB100M
Alternative model
2011
D3L
6TPE100MAZB
Year of
deletion
2012
TPB
10TPB47M
2009
Models for
deletion
2R5TPE680MIL
B2
2009
6TPB100MA
Size
code
2R5TPE680ML
Surface mount type
8TPB47M
Series
D3L
TPE
D4
TPG
TPL
B1G
S09
TPU
S11
A09
D2
TH
D3L
D4
C
TQC
D2
D3L
D3
OS-CON
Line-up
Guidelines and
precautions
Selection guide
●EOL Models
The following table is a list of the End-Of-Life (EOL) models.
Sales of these items will end as soon as we run out of its stock.
We would like to express our appreciation for your business over the years with these products
and we hope the new, alternative parts will continue to serve your needs.
Thank you very much.
TPA
D3
B2
C
TPB
D3L
D3
C1
TPC
D2
TPD
D4D
EOL
time
Alternative model
Series
Size
code
EOL
time
EOL models
Alternative model
10TPA33M
2012/9
10TPB33M
2R5TPE220MPB
2012/9
2R5TPE220MLB
6TPA47M
2012/9
10TPB47M
8TPE100MPC2
2012/9
10TPF150ML
10TPA100M
2012/9
10TPC100M
6TPE150MPC2
2012/9
6TPE150M
6TPA150M
2012/9
6TPC150M
6TPE150MIC2
2012/9
6TPE150MI
4TPA220M
2012/9
4TPE220M
4TPE220MPC2
2012/9
4TPE220MI
8TPB33M
2012/9
10TPB33M
4TPE220MIC2
2012/9
4TPE220MI
4TPB150MA
2012/9
4TPE150MAZB
4TPE220MFC2
2012/9
4TPE220MF
4TPB100MV
2012/9
4TPE100MZB
2R5TPE330MIC2
2012/9
2R5TPE330MF
10TPB220MC
2009/10 -
2R5TPE330MFC2
2012/9
2R5TPE330MF
10TPB68MC
2012/9
10TPC68M
2R5TPE330MCC2
2012/9
2R5TPE330MC
10TPB47MC
2012/9
10TPC68M
2R5TPE330M9C2
2012/9
2R5TPE330M9
8TPB82MC
2012/9
8TPE100MAZB
10TPE180MGC
2012/9
10TPE220ML
6TPB150MC
2012/9
6TPE150M
10TPE150MGC
2012/9
10TPE220ML
6TPB100MC
2012/9
6TPG100MG
6TPE220MPC
2012/9
6TPE220M
4TPB220MC
2012/9
4TPE220MI
6TPE220MIC
2012/9
6TPE220MI
4TPB150MC
2012/9
6TPE150M
6TPE150MPC
2012/9
6TPE150M
2R5TPB220MC
2012/9
4TPE220MI
4TPE220MPC
2012/9
4TPE220MI
16TPB47ML
2003/6
16TQC47MYFD
4TPE220MIC
2012/9
4TPE220MI
2R5TPB680ML
2012/9
2R5TPE680MFL
2R5TPE330MPC
2012/9
2R5TPE330MF
2R5TPB470ML
2012/9
2R5TPE470MI
2R5TPE330MIC
2012/9
2R5TPE330MF
16TPB47M
2003/6
16TQC47MYFD
2R5TPE330MFC
2012/9
2R5TPE330MF
2R5TPB330M
2012/9
2R5TPE330M
2TPF470M6
2012/9
2R5TPF470M6L
8TPC33M
2012/9
12TPG33M
6TPG68MG
2012/9
6TPG100M
6TPC100MC
2012/9
6TPG100MG
4TPG150M
2012/9 ６TPG150M
6TPC68M
2012/9
6TPG100MG
2R5TPL330M7
2011/7
-
4TPC100M
2012/9
6TPG100MG
2R5TPL220MC
2012/9
-
4TPC56M
2012/9
-
2TPLF560M6
2011/7
-
2R5TPC82M
2012/9
-
2TPLF470M7
2012/9
-
16TPC33M
2003/6
16TQC33MYFD
2TPSF270MC
2012/9
2TPSF270M9G
2R5TPC220M
2012/9
2R5TPE220M
2TPSF270M9
2012/9
2TPSF270M9G
10TPD150M
2007/10 10TPF150ML
6TPU10M
2012/9
6TPU10MSI
B2
C2
TPE
C3
TPF
D2E
TPG
B1G
TPL
D2T
TPLF
D2T
TPSF
B2S
6TPF470MAH
Surface mount type
Radial lead type
EOL series
POSCAP
Line-up
Guidelines and
precautions
Selection guide
C
EOL models
Technical data
Size
code
Series system
diagram
Image of
case size
Products list
Explanation of
part numbers
Packing
specifications
Recommended
soldering
condition
Fundamental
structure
Ｃharacteristics
6TPD470M
2012/3
4TPU15M
2012/9
6TPU22MSI
6TPD330M
2007/10 6TPF330M9L
2R5TPU22M
2012/9
6TPU22MSI
6TPD220M
2007/10 6TPF220ML
6TPU22MSK
2012/9
6TPU22MSI
4TPD680M
2012/3
4TPU33MSK
2012/9
6TPU47MSI
4TPD470M
2007/10 4TPF470ML
2R5TPU47MSK
2012/9
2R5TPU47MSI
TPH
4TPD330M
2007/10 4TPF330ML
8TPU33MBI
2012/9
ATPH33MAHA
2R5TPD1000M
2012/3
ETPF1000M6H
6TPU47MBI
2012/9
6TPH47MHA
TPG
2R5TPD1000M8
2012/3
ETPF1000M6H
4TPU68MBI
2012/9
4TPH68MHA
2R5TPD1000M6
2012/3
ETPF1000M6H
2R5THB470ML
2012/9
6THB470M
2R5TPD1000M5
2012/3
ETPF1000M5H
2R5THB1000M
2012/9
-
2R5TPD680M
2007/10 2R5TPF680ML
2R5THB680M
2012/9
-
2R5TPD680M8
2007/10 2R5TPF680M7L
6THD330M
2012/3
6TPF330M9L
2R5TPD680M6
2012/3
2R5TPF680M6L
4THD470M
2012/9
-
2R5TPD680M5
2012/3
ETPF680M5H
2R5THD680M
2012/3
2R5TPF680M6L
2R5TPD470M
2007/10 2R5TPF470ML
2R5TPD470M8
2007/10 2R5TPF470M7L
2R5TPD470M6
2012/3
2R5TPD470M5
2012/3
4TPF680MAH
S08
TPU
S11
B09
D3L
D4
TH
D4D
Reliability
TPU
TPSF
Surface mount type
Series
Technical data
TPE
TPB
TPC
TPF
TA
TR seｒies
-
TA series
TV
APA
D2A
APA series
2006/4
-
TH
2R5TPF470M6L
APB
D1
APB series
2006/4
-
ETPF470M5H
APC
D2
APC series
2009/6
-
APD
D1
APD series
2009/6
-
※ Blue letters: added or changed models at this year.
TR
TQC
EOL models
102

Panasonic Poscap Catalog

Transcription

Similar documents

dedocool - Dedolight

5MPFSERIES Polypropylene Capacitor with Fuseac® Technology

P4400 KAW spec sheet V4b

Skynet

Kenda - Bearclaw HTR - Modern Tire Company

Audience Auricap Capacitor Applications

The Z-Brick® is a peice of test equipment to quickly check the

6SL7 Series Tubes

12BH7 TJ FullMusic

6SN7 SE TJ FullMusic