Rotary Actuators DA-H Series

Rotary actuators
DA-H – series
HKS Unternehmensgruppe
Leipziger Straße 53-55
D-63607 Wächtersbach-Aufenau
Phone: +49 (0) 60 53 / 6163 - 0
Extension Const. -11 / Sales. -21
Telefax: +49 (0) 60 53 / 6163 - 39
E-Mail: [email protected]
Internet: www.hks-partner.com
We reserve the right to make modifications
Copyright © 2006 by HKS
Technical informations DA-H 40
Hydraulic rotary actuator
General characteristics
Rotary actuators in the DA-H series are characterised
by their performance range. At a working pressure of
up to 210 bars, torques of up to 250,000 Nm are
possible (higher working pressures on request).
Another characteristic is the extremely low angular
clearance.
HKS rotary actuators in the DA-H series offer the
following standards:
-
20 sizes from 36 to 250000 Nm with pistons
Ø 40– Ø 450 mm
4 rotary angle rages for each size: 90°, 180°,
270° and 360°
Actuator shaft with 2 feather keys or DIN
5480 involute spline
Tandem seal on the actuator shaft
Because of the almost infinite design possibilities for
the front face almost all connection variants can be
achieved with these actuators.
Auxiliary equipment
Cushioning at both ends
Rotary angle adjustment up to + 4°
Camshaft
Hollow shaft with DIN 5463, DIN 5480 or
DIN 6885 profile
Special versions
Actuator shaft with spline profile to DIN
5463
Actuator shaft with second drive cog
Actuator shaft and mounting flange
designed to customer’s requirements
Rotary angle adjustment throughout the
range of rotation
Limit switch equipment
Direct valve connection, 3 mounting
positions
All intermediate rotation angles can be
supplied
Range of rotation exceeding 360°
Sea-water resistant
Additional bearing for high radial forces
Change of direction of rotation
Further special versions are available
Fig. 1
Technical data Type DA-H 40
Max. nominal torque at 210 bars
Max. nominal torque at 210 bars
with camshaft
Nominal torque
Max. working pressure *
Max. radial load
Max. axial load
Absorption volume
Angle 90°
Angle 180°
Angle 270°
Angle 360°
Weight
Angle 90°
Angle 180°
Angle 270°
Angle 360°
*) Working pressures > 210 bar on request
Nm
Nm
Nm/bar
bar
N
N
dm3
dm3
dm3
dm3
kg
kg
kg
200
160
0,96
210
1567
8 000
0,017
0,034
0,050
0,067
approx 4,3
approx 4,8
approx 5,8
kg approx 6,2
Functional description
The oil pressure supplied through connections P1 and P2 causes actuator
shaft G to perform a rotary movement. The linear movement of piston K is
here converted to a rotary movement by multiple helical gears in the housing,
piston and shaft.
Direction of rotation
With the pressure at P1 actuator shaft G1 rotates from the initial position to
the left (anticlockwise).
A change in direction of rotation is possible in a special version.
Normal position of the feather key:
Figure 1 shows the factory set position of piston K Changes of position are
possible.
TI DA-H 40 - 0606 E
Typical applications
HKS rotary actuators have proved their worth
throughout the industrial sector. For example, they
are used in construction machinery, machine tools,
bending machines, foundry, mining, agricultural and
packing machines, transfer lines, manipulators,
armatures, as well as in shipbuilding, motor vehicles,
assembly platforms and in ventilation engineering.
HKS rotary actuators are reliable and require no
maintenance. This is demonstrated, for example, 2300
mm below sea-level, whey they are used as actuators
for armatures.
Angle of rotation and its adjustment
In the standard version the angle of rotation may be up to 4° in the positive
range. An exact angle of rotation is achieved by means of an additional device
WV.
Cushioning
The speed of rotation of actuator shaft G can be regulated in the limit
positions by throttle check valves. Further information on the subject of
cushioning may be requested on an additional page.
We reserve the right to make modifications
Copyright © 2006 by HKS
Technical informations DA-H 40
Hydraulic rotary actuator
Dimension table
Standard version with feather key
Special version hollow shaft DIN 5463
Special version hollow shaft with feather key grooves (DIN 6885)
Special version angle adjustment
Special version threaded camshaft
Special version with female thread
Special version camshaft with cog
Typ
Ak6
DIN 5480*)
B
Ø
Cf7
Ø
D
E
Ø
F
Ø
G
H DIN 6885
I DIN 6885
J DIN 6885
K
L
M
N
O
P
90°
180°
270°
360°
Q
R
90°
180°
270°
360°
S
45°
T
U Number
U
DA-H 40
22
W 22x1,25x16x8f
98
55
43
65
75
2,5
45
8
14
84
50
3
4
16
124
149
182
210
39
28
41
55
68,5
G 1/8"
60°
5
9
Special version HW-hollow shaft to
DIN 5480 on request
B
26
Spline profile DIN 5463
6x11x14
HKS Unternehmensgruppe
Leipziger Straße 53-55
D-63607 Wächtersbach-Aufenau
Phone: +49 (0) 60 53 / 6163 - 0
Extension Const. -11 / Sales. -21
Telefax: +49 (0) 60 53 / 6163 - 39
E-Mail: [email protected]
Internet: www.hks-partner.com
Special version with camshaft
W f7
16
W1 h6
10
Special version with angle
adjustment/camshaft/camshaft
with tapped hole/camshaft with
pivot
P1
90°
142
180°
167
270°
200
360°
228
Special version HWP - Hollow shaft
with key grooves (DIN 6885)
H1
45
J1
7,8
CH7
Ø
12
I1P9
4
*) Special version KW spline shaft
DIN is not shown
N.B.: In the hollow shaft version it is
necessary to construct the shaft in a
high strength material. A calculation
of the shaft for torsional strength is
strongly recommended.
We reserve the right to make modifications
Copyright © 2006 by HKS
Technical informations DA-H 50
Hydraulic rotary actuator
General characteristics
Rotary actuators in the DA-H series are characterised
by their performance range. At a working pressure of
up to 210 bars, torques of up to 250,000 Nm are
possible (higher working pressures on request).
Another characteristic is the extremely low angular
clearance.
HKS rotary actuators in the DA-H series offer the
following standards:
-
20 sizes from 36 to 250000 Nm with pistons
Ø 40– Ø 450 mm
4 rotary angle rages for each size: 90°, 180°,
270° and 360°
Actuator shaft with 2 feather keys or DIN
5480 involute spline
Tandem seal on the actuator shaft
Because of the almost infinite design possibilities for
the front face almost all connection variants can be
achieved with these actuators.
Auxiliary equipment
Cushioning at both ends
Rotary angle adjustment up to + 4°
Camshaft
Hollow shaft with DIN 5463, DIN 5480 or
DIN 6885 profile
Special versions
Actuator shaft with spline profile to DIN
5463
Actuator shaft with second drive cog
Actuator shaft and mounting flange
designed to customer’s requirements
Rotary angle adjustment throughout the
range of rotation
Limit switch equipment
Direct valve connection, 3 mounting
positions
All intermediate rotation angles can be
supplied
Range of rotation exceeding 360°
Sea-water resistant
Additional bearing for high radial forces
Change of direction of rotation
Further special versions are available
Fig. 1
Technical data Type DA-H 50
Max. nominal torque at 210 bars
Max. nominal torque at 210 bars
with camshaft
Nominal torque
Max. working pressure *
Max. radial load
Max. axial load
Absorption volume
Angle 90°
Angle 180°
Angle 270°
Angle 360°
Weight
Angle 90°
Angle 180°
Angle 270°
Angle 360°
*) Working pressures > 210 bar on request
Nm
Nm
Nm/bar
bar
N
N
dm3
dm3
dm3
dm3
kg
kg
kg
kg
340
290
1,62
210
2976
10000
0,028
0,056
0,084
0,113
ca. 6
ca. 6,8
ca. 7,8
ca. 8,7
Functional description
The oil pressure supplied through connections P1 and P2 causes actuator
shaft G to perform a rotary movement. The linear movement of piston K is
here converted to a rotary movement by multiple helical gears in the housing,
piston and shaft.
Direction of rotation
With the pressure at P1 actuator shaft G1 rotates from the initial position to
the left (anticlockwise).
A change in direction of rotation is possible in a special version.
Normal position of the feather key:
Figure 1 shows the factory set position of piston K Changes of position are
possible.
TI DA-H 50 - 0606 E
Typical applications
HKS rotary actuators have proved their worth
throughout the industrial sector. For example, they
are used in construction machinery, machine tools,
bending machines, foundry, mining, agricultural and
packing machines, transfer lines, manipulators,
armatures, as well as in shipbuilding, motor vehicles,
assembly platforms and in ventilation engineering.
HKS rotary actuators are reliable and require no
maintenance. This is demonstrated, for example, 2300
mm below sea-level, whey they are used as actuators
for armatures.
Angle of rotation and its adjustment
In the standard version the angle of rotation may be up to 4° in the positive
range. An exact angle of rotation is achieved by means of an additional device
WV.
Cushioning
The speed of rotation of actuator shaft G can be regulated in the limit
positions by throttle check valves. Further information on the subject of
cushioning may be requested on an additional page.
We reserve the right to make modifications
Copyright © 2006 by HKS
Technical informations DA-H 50
Hydraulic rotary actuator
Dimension table
Standard version with feather key
Special version hollow shaft DIN 5463
Special version hollow shaft with feather key grooves (DIN 6885)
Special version angle adjustment
Special version threaded camshaft
Special version with female thread
Special version camshaft with cog
Typ
Ak6
DIN 5480*)
B
Ø
Cf7
Ø
D
E
Ø
F
Ø
G
H DIN 6885
I DIN 6885
J DIN 6885
K
L
M
N
O
P
90°
180°
270°
360°
Q
R
90°
180°
270°
360°
S
45°
T
U Number
U
DA-H 50
28
W 28x2x12x8f
110
68
49
72
82
2
56
8
17
90
60
3
4
18
133
164
200
232
39
31
48
65
80,5
G 1/8"
60°
5
9
Special version HW-hollow shaft to
DIN 5480 on request
B
30
Spline profile DIN 5463
6x16x20
HKS Unternehmensgruppe
Leipziger Straße 53-55
D-63607 Wächtersbach-Aufenau
Phone: +49 (0) 60 53 / 6163 - 0
Extension Const. -11 / Sales. -21
Telefax: +49 (0) 60 53 / 6163 - 39
E-Mail: [email protected]
Internet: www.hks-partner.com
Special version with camshaft
W f7
18
W1 h6
10
Special version with angle
adjustment/camshaft/camshaft
with tapped hole/camshaft with
pivot
P1
90°
149
180°
182
270°
218
360°
250
Special version HWP - Hollow shaft
with key grooves (DIN 6885)
H1
55
J1
10,1
CH7
Ø
16
I1P9
5
*) Special version KW spline shaft
DIN is not shown
N.B.: In the hollow shaft version it is
necessary to construct the shaft in a
high strength material. A calculation of
the shaft for torsional strength is
strongly recommended.
We reserve the right to make modifications
Copyright © 2006 by HKS
Technical informations DA-H 63
Hydraulic rotary actuator
General characteristics
Rotary actuators in the DA-H series are characterised
by their performance range. At a working pressure of
up to 210 bars, torques of up to 250,000 Nm are
possible (higher working pressures on request).
Another characteristic is the extremely low angular
clearance.
HKS rotary actuators in the DA-H series offer the
following standards:
-
20 sizes from 36 to 250000 Nm with pistons
Ø 40– Ø 450 mm
4 rotary angle rages for each size: 90°, 180°,
270° and 360°
Actuator shaft with 2 feather keys or DIN
5480 involute spline
Tandem seal on the actuator shaft
Because of the almost infinite design possibilities for
the front face almost all connection variants can be
achieved with these actuators.
Auxiliary equipment
Cushioning at both ends
Rotary angle adjustment up to + 4°
Camshaft
Hollow shaft with DIN 5463, DIN 5480 or
DIN 6885 profile
Special versions
Actuator shaft with spline profile to DIN
5463
Actuator shaft with second drive cog
Actuator shaft and mounting flange
designed to customer’s requirements
Rotary angle adjustment throughout the
range of rotation
Limit switch equipment
Direct valve connection, 3 mounting
positions
All intermediate rotation angles can be
supplied
Range of rotation exceeding 360°
Sea-water resistant
Additional bearing for high radial forces
Change of direction of rotation
Further special versions are available
Fig. 1
Technical data Type DA-H 63
Max. nominal torque at 210 bars
Max. nominal torque at 210 bars
with camshaft
Nominal torque
Max. working pressure *
Max. radial load
Max. axial load
Absorption volume
Angle 90°
Angle 180°
Angle 270°
Angle 360°
Weight
Angle 90°
Angle 180°
Angle 270°
Angle 360°
*) Working pressures > 210 bar on request
Nm
Nm
Nm/bar
bar
N
N
dm3
dm3
dm3
dm3
kg
kg
kg
kg
650
540
3,10
210
4364
14000
0,058
0,117
0,176
0,235
ca. 8,5
ca. 9,8
ca. 12,9
ca. 14
Functional description
The oil pressure supplied through connections P1 and P2 causes actuator
shaft G to perform a rotary movement. The linear movement of piston K is
here converted to a rotary movement by multiple helical gears in the housing,
piston and shaft.
Direction of rotation
With the pressure at P1 actuator shaft G1 rotates from the initial position to
the left (anticlockwise).
A change in direction of rotation is possible in a special version.
Normal position of the feather key:
Figure 1 shows the factory set position of piston K Changes of position are
possible.
TI DA-H 63 - 0606 E
Typical applications
HKS rotary actuators have proved their worth
throughout the industrial sector. For example, they
are used in construction machinery, machine tools,
bending machines, foundry, mining, agricultural and
packing machines, transfer lines, manipulators,
armatures, as well as in shipbuilding, motor vehicles,
assembly platforms and in ventilation engineering.
HKS rotary actuators are reliable and require no
maintenance. This is demonstrated, for example, 2300
mm below sea-level, whey they are used as actuators
for armatures.
Angle of rotation and its adjustment
In the standard version the angle of rotation may be up to 4° in the positive
range. An exact angle of rotation is achieved by means of an additional device
WV.
Cushioning
The speed of rotation of actuator shaft G can be regulated in the limit
positions by throttle check valves. Further information on the subject of
cushioning may be requested on an additional page.
We reserve the right to make modifications
Copyright © 2006 by HKS
Technical informations DA-H 63
Hydraulic rotary actuator
Dimension table
Standard version with feather key
Special version hollow shaft DIN 5463
Special version hollow shaft with feather key grooves (DIN 6885)
Special version angle adjustment
Special version threaded camshaft
Special version with female thread
Special version camshaft with cog
Typ
Ak6
DIN 5480*)
B
Ø
Cf7
Ø
D
E
Ø
F
Ø
G
H DIN 6885
I DIN 6885
J DIN 6885
K
L
M
N
O
P
90°
180°
270°
360°
Q
R
90°
180°
270°
360°
S
45°
T
U Number
U
DA-H 63
35
W 35x2x16x8f
128
80
57
87
95
5
70
10
20,5
108
80
3,5
5
25
152
200
245
284
48
37
57
79
99
G 1/4"
60°
5
11
Special version HW-hollow shaft to
DIN 5480 on request
B
35
Spline profile DIN 5463
6x21x25
HKS Unternehmensgruppe
Leipziger Straße 53-55
D-63607 Wächtersbach-Aufenau
Phone: +49 (0) 60 53 / 6163 - 0
Extension Const. -11 / Sales. -21
Telefax: +49 (0) 60 53 / 6163 - 39
E-Mail: [email protected]
Internet: www.hks-partner.com
Special version with camshaft
W f7
18
W1 h6
10
Special version with angle
adjustment/camshaft/camshaft
with tapped hole/camshaft with
pivot
P1
90°
172
180°
220
270°
264,5
360°
304,5
Special version HWP - Hollow shaft
with key grooves (DIN 6885)
H1
65
J1
14,1
CH7
Ø
24
I1P9
8
*) Special version KW spline shaft
DIN is not shown
N.B.: In the hollow shaft version it is
necessary to construct the shaft in a
high strength material. A calculation of
the shaft for torsional strength is
strongly recommended.
We reserve the right to make modifications
Copyright © 2006 by HKS
Technical informations DA-H 80
Hydraulic rotary actuator
General characteristics
Rotary actuators in the DA-H series are characterised
by their performance range. At a working pressure of
up to 210 bars, torques of up to 250,000 Nm are
possible (higher working pressures on request).
Another characteristic is the extremely low angular
clearance.
HKS rotary actuators in the DA-H series offer the
following standards:
-
20 sizes from 36 to 250000 Nm with pistons
Ø 40– Ø 450 mm
4 rotary angle rages for each size: 90°, 180°,
270° and 360°
Actuator shaft with 2 feather keys or DIN
5480 involute spline
Tandem seal on the actuator shaft
Because of the almost infinite design possibilities for
the front face almost all connection variants can be
achieved with these actuators.
Auxiliary equipment
Cushioning at both ends
Rotary angle adjustment up to + 4°
Camshaft
Hollow shaft with DIN 5463, DIN 5480 or
DIN 6885 profile
Special versions
Actuator shaft with spline profile to DIN
5463
Actuator shaft with second drive cog
Actuator shaft and mounting flange
designed to customer’s requirements
Rotary angle adjustment throughout the
range of rotation
Limit switch equipment
Direct valve connection, 3 mounting
positions
All intermediate rotation angles can be
supplied
Range of rotation exceeding 360°
Sea-water resistant
Additional bearing for high radial forces
Change of direction of rotation
Further special versions are available
Fig. 1
Technical data Type DA-H 80
Max. nominal torque at 210 bars
Max. nominal torque at 210 bars
with camshaft
Nominal torque
Max. working pressure *
Max. radial load
Max. axial load
Absorption volume
Angle 90°
Angle 180°
Angle 270°
Angle 360°
Weight
Angle 90°
Angle 180°
Angle 270°
Angle 360°
*) Working pressures > 210 bar on request
Nm
1300
Nm
Nm/bar
bar
N
N
dm3
dm3
dm3
dm3
kg
kg
kg
kg
1170
6,20
210
7875
19050
0,093
0,186
0,279
0,372
ca. 16,7
ca. 19,1
ca. 21,5
ca. 24
Functional description
The oil pressure supplied through connections P1 and P2 causes actuator
shaft G to perform a rotary movement. The linear movement of piston K is
here converted to a rotary movement by multiple helical gears in the housing,
piston and shaft.
Direction of rotation
With the pressure at P1 actuator shaft G1 rotates from the initial position to
the left (anticlockwise).
A change in direction of rotation is possible in a special version.
Normal position of the feather key:
Figure 1 shows the factory set position of piston K Changes of position are
possible.
TI DA-H 80 - 0606 E
Typical applications
HKS rotary actuators have proved their worth
throughout the industrial sector. For example, they
are used in construction machinery, machine tools,
bending machines, foundry, mining, agricultural and
packing machines, transfer lines, manipulators,
armatures, as well as in shipbuilding, motor vehicles,
assembly platforms and in ventilation engineering.
HKS rotary actuators are reliable and require no
maintenance. This is demonstrated, for example, 2300
mm below sea-level, whey they are used as actuators
for armatures.
Angle of rotation and its adjustment
In the standard version the angle of rotation may be up to 4° in the positive
range. An exact angle of rotation is achieved by means of an additional device
WV.
Cushioning
The speed of rotation of actuator shaft G can be regulated in the limit
positions by throttle check valves. Further information on the subject of
cushioning may be requested on an additional page.
We reserve the right to make modifications
Copyright © 2006 by HKS
Technical informations DA-H 80
Hydraulic rotary actuator
Dimension table
Standard version with feather key
Special version hollow shaft DIN 5463
Special version hollow shaft with feather key grooves (DIN 6885)
Special version angle adjustment
Special version threaded camshaft
Special version with female thread
Special version camshaft with cog
Typ
Ak6
DIN 5480*)
B
Ø
Cf7
Ø
D
E
Ø
F
Ø
G
H DIN 6885
I DIN 6885
J DIN 6885
K
L
M
N
O
P
90°
180°
270°
360°
Q
R
90°
180°
270°
360°
S
45°
T
U Number
U
DA-H 80
42
W 40x2x18x8f
150
100
66
108
118
5
100
12
24
130
110
3
6
30
187
240
290
345
57
37
74
101
125
G 3/8"
45°
7
11
Special version HW-hollow shaft to
DIN 5480 on request
B
40
Spline profile DIN 5463
6x26x32
HKS Unternehmensgruppe
Leipziger Straße 53-55
D-63607 Wächtersbach-Aufenau
Phone: +49 (0) 60 53 / 6163 - 0
Extension Const. -11 / Sales. -21
Telefax: +49 (0) 60 53 / 6163 - 39
E-Mail: [email protected]
Internet: www.hks-partner.com
Special version with camshaft
W f7
25
W1 h6
16
Special version with angle
adjustment/camshaft/camshaft
with tapped hole/camshaft with
pivot
P1
90°
212
180°
262
270°
314,5
360°
367,5
Special version HWP - Hollow shaft
with key grooves (DIN 6885)
H1
90
J1
18,3
CH7
Ø
30
I1P9
8
*) Special version KW spline shaft
DIN is not shown
N.B.: In the hollow shaft version it is
necessary to construct the shaft in a
high strength material. A calculation of
the shaft for torsional strength is
strongly recommended.
We reserve the right to make modifications
Copyright © 2006 by HKS
Technical informations DA-H 100
Hydraulic rotary actuator
General characteristics
Rotary actuators in the DA-H series are characterised
by their performance range. At a working pressure of
up to 210 bars, torques of up to 250,000 Nm are
possible (higher working pressures on request).
Another characteristic is the extremely low angular
clearance.
HKS rotary actuators in the DA-H series offer the
following standards:
-
20 sizes from 36 to 250000 Nm with pistons
Ø 40– Ø 450 mm
4 rotary angle rages for each size: 90°, 180°,
270° and 360°
Actuator shaft with 2 feather keys or DIN
5480 involute spline
Tandem seal on the actuator shaft
Because of the almost infinite design possibilities for
the front face almost all connection variants can be
achieved with these actuators.
Auxiliary equipment
Cushioning at both ends
Rotary angle adjustment up to + 4°
Camshaft
Hollow shaft with DIN 5463, DIN 5480 or
DIN 6885 profile
Special versions
Actuator shaft with spline profile to DIN
5463
Actuator shaft with second drive cog
Actuator shaft and mounting flange
designed to customer’s requirements
Rotary angle adjustment throughout the
range of rotation
Limit switch equipment
Direct valve connection, 3 mounting
positions
All intermediate rotation angles can be
supplied
Range of rotation exceeding 360°
Sea-water resistant
Additional bearing for high radial forces
Change of direction of rotation
Further special versions are available
Fig. 1
Technical data Type DA-H 100
Max. nominal torque at 210 bars
Max. nominal torque at 210 bars
with camshaft
Nominal torque
Max. working pressure *
Max. radial load
Max. axial load
Absorption volume
Angle 90°
Angle 180°
Angle 270°
Angle 360°
Weight
Angle 90°
Angle 180°
Angle 270°
Angle 360°
*) Working pressures > 210 bar on request
Nm
2500
Nm
Nm/bar
bar
N
N
dm3
dm3
dm3
dm3
kg
kg
kg
kg
2340
11,90
210
11250
24900
0,235
0,471
0,706
0,941
ca.24,1
ca.29,2
ca.34
ca.38,5
Functional description
The oil pressure supplied through connections P1 and P2 causes actuator
shaft G to perform a rotary movement. The linear movement of piston K is
here converted to a rotary movement by multiple helical gears in the housing,
piston and shaft.
Direction of rotation
With the pressure at P1 actuator shaft G1 rotates from the initial position to
the left (anticlockwise).
A change in direction of rotation is possible in a special version.
Normal position of the feather key:
Figure 1 shows the factory set position of piston K Changes of position are
possible.
TI DA-H 100 - 0606 E
Typical applications
HKS rotary actuators have proved their worth
throughout the industrial sector. For example, they
are used in construction machinery, machine tools,
bending machines, foundry, mining, agricultural and
packing machines, transfer lines, manipulators,
armatures, as well as in shipbuilding, motor vehicles,
assembly platforms and in ventilation engineering.
HKS rotary actuators are reliable and require no
maintenance. This is demonstrated, for example, 2300
mm below sea-level, whey they are used as actuators
for armatures.
Angle of rotation and its adjustment
In the standard version the angle of rotation may be up to 4° in the positive
range. An exact angle of rotation is achieved by means of an additional device
WV.
Cushioning
The speed of rotation of actuator shaft G can be regulated in the limit
positions by throttle check valves. Further information on the subject of
cushioning may be requested on an additional page.
We reserve the right to make modifications
Copyright © 2006 by HKS
Technical informations DA-H 100
Hydraulic rotary actuator
Dimension table
Standard version with feather key
Special version hollow shaft DIN 5463
Special version hollow shaft with feather key grooves (DIN 6885)
Special version angle adjustment
Special version threaded camshaft
Special version with female thread
Special version camshaft with cog
Typ
Am6
DIN 5480*)
B
Ø
Cf7
Ø
D
E
Ø
F
Ø
G
H DIN 6885
I DIN 6885
J DIN 6885
K
L
M
N
O
P
90°
180°
270°
360°
Q
R
90°
180°
270°
360°
S
45°
T
U Number
U
DA-H 100
55
W 55x2x26x8f
178
115
80
130
147
5
100
16
31,5
155
110
4
6
31
241
311
366
432
65
56,5
89
121,5
154
G 1/2"
45°
7
14
Special version HW-hollow shaft to
DIN 5480 on request
B
50
Spline profile DIN 5463
8x36x42
HKS Unternehmensgruppe
Leipziger Straße 53-55
D-63607 Wächtersbach-Aufenau
Phone: +49 (0) 60 53 / 6163 - 0
Extension Const. -11 / Sales. -21
Telefax: +49 (0) 60 53 / 6163 - 39
E-Mail: [email protected]
Internet: www.hks-partner.com
Special version with camshaft
W f7
25
W1 h6
16
Special version with angle
adjustment/camshaft/camshaft
with tapped hole/camshaft with
pivot
P1
90°
245
180°
311
270°
381
360°
442
Special version HWP - Hollow shaft
with key grooves (DIN 6885)
H1
105
J1
24,3
CH7
Ø
42
I1P9
12
*) Special version KW spline shaft
DIN is not shown
N.B.: In the hollow shaft version it is
necessary to construct the shaft in a
high strength material. A calculation of
the shaft for torsional strength is
strongly recommended.
We reserve the right to make modifications
Copyright © 2006 by HKS
Technical informations DA-H 125
Hydraulic rotary actuator
General characteristics
Rotary actuators in the DA-H series are characterised
by their performance range. At a working pressure of
up to 210 bars, torques of up to 250,000 Nm are
possible (higher working pressures on request).
Another characteristic is the extremely low angular
clearance.
HKS rotary actuators in the DA-H series offer the
following standards:
-
20 sizes from 36 to 250000 Nm with pistons
Ø 40– Ø 450 mm
4 rotary angle rages for each size: 90°, 180°,
270° and 360°
Actuator shaft with 2 feather keys or DIN
5480 involute spline
Tandem seal on the actuator shaft
Because of the almost infinite design possibilities for
the front face almost all connection variants can be
achieved with these actuators.
Auxiliary equipment
Cushioning at both ends
Rotary angle adjustment up to + 4°
Camshaft
Hollow shaft with DIN 5463, DIN 5480 or
DIN 6885 profile
Special versions
Actuator shaft with spline profile to DIN
5463
Actuator shaft with second drive cog
Actuator shaft and mounting flange
designed to customer’s requirements
Rotary angle adjustment throughout the
range of rotation
Limit switch equipment
Direct valve connection, 3 mounting
positions
All intermediate rotation angles can be
supplied
Range of rotation exceeding 360°
Sea-water resistant
Additional bearing for high radial forces
Change of direction of rotation
Further special versions are available
Fig. 1
Technical data Type DA-H 125
Max. nominal torque at 210 bars
Max. nominal torque at 210 bars
with camshaft
Nominal torque
Max. working pressure *
Max. radial load
Max. axial load
Absorption volume
Angle 90°
Angle 180°
Angle 270°
Angle 360°
Weight
Angle 90°
Angle 180°
Angle 270°
Angle 360°
*) Working pressures > 210 bar on request
Nm
5107
Nm
Nm/bar
bar
N
N
dm3
dm3
dm3
dm3
kg
kg
kg
kg
4900
24,32
210
17552
34100
0,497
0,995
1,492
1,989
ca. 47
ca. 55
ca. 63,5
ca. 72,5
Functional description
The oil pressure supplied through connections P1 and P2 causes actuator
shaft G to perform a rotary movement. The linear movement of piston K is
here converted to a rotary movement by multiple helical gears in the housing,
piston and shaft.
Direction of rotation
With the pressure at P1 actuator shaft G1 rotates from the initial position to
the left (anticlockwise).
A change in direction of rotation is possible in a special version.
Normal position of the feather key:
Figure 1 shows the factory set position of piston K Changes of position are
possible.
TI DA-H 125 - 0606 E
Typical applications
HKS rotary actuators have proved their worth
throughout the industrial sector. For example, they
are used in construction machinery, machine tools,
bending machines, foundry, mining, agricultural and
packing machines, transfer lines, manipulators,
armatures, as well as in shipbuilding, motor vehicles,
assembly platforms and in ventilation engineering.
HKS rotary actuators are reliable and require no
maintenance. This is demonstrated, for example, 2300
mm below sea-level, whey they are used as actuators
for armatures.
Angle of rotation and its adjustment
In the standard version the angle of rotation may be up to 4° in the positive
range. An exact angle of rotation is achieved by means of an additional device
WV.
Cushioning
The speed of rotation of actuator shaft G can be regulated in the limit
positions by throttle check valves. Further information on the subject of
cushioning may be requested on an additional page.
We reserve the right to make modifications
Copyright © 2006 by HKS
Technical informations DA-H 125
Hydraulic rotary actuator
Dimension table
Standard version with feather key
Special version hollow shaft DIN 5463
Special version hollow shaft with feather key grooves (DIN 6885)
Special version angle adjustment
Special version threaded camshaft
Special version with female thread
Special version camshaft with cog
Typ
Am6
DIN 5480*)
B
Ø
Cf7
Ø
D
E
Ø
F
Ø
G
H DIN 6885
I DIN 6885
J DIN 6885
K
L
M
N
O
P
90°
180°
270°
360°
Q
R
90°
180°
270°
360°
S
45°
T
U Number
U
DA-H 125
70
W 70x2x34x8f
222
150
94
167
183
7
125
20
39,5
195
140
4
8
37
271,5
392
480
532,5
74
76,2
118,5
162,5
207
G 1/2"
40°
8
18
Special version HW-hollow shaft to
DIN 5480 on request
B
62
Spline profile DIN 5463
8x46x54
HKS Unternehmensgruppe
Leipziger Straße 53-55
D-63607 Wächtersbach-Aufenau
Phone: +49 (0) 60 53 / 6163 - 0
Extension Const. -11 / Sales. -21
Telefax: +49 (0) 60 53 / 6163 - 39
E-Mail: [email protected]
Internet: www.hks-partner.com
Special version with camshaft
W f7
25
W1 h6
16
Special version with angle
adjustment/camshaft/camshaft
with tapped hole/camshaft with
pivot
P1
90°
298
180°
392
270°
482
360°
557
Special version HWP - Hollow shaft
with key grooves (DIN 6885)
H1
120
J1
31,8
CH7
Ø
55
I1P9
16
*) Special version KW spline shaft
DIN is not shown
N.B.: In the hollow shaft version it is
necessary to construct the shaft in a
high strength material. A calculation of
the shaft for torsional strength is
strongly recommended.
We reserve the right to make modifications
Copyright © 2006 by HKS
Technical informations DA-H 140
Hydraulic rotary actuator
General characteristics
Rotary actuators in the DA-H series are characterised
by their performance range. At a working pressure of
up to 210 bars, torques of up to 250,000 Nm are
possible (higher working pressures on request).
Another characteristic is the extremely low angular
clearance.
HKS rotary actuators in the DA-H series offer the
following standards:
-
20 sizes from 36 to 250000 Nm with pistons
Ø 40– Ø 450 mm
4 rotary angle rages for each size: 90°, 180°,
270° and 360°
Actuator shaft with 2 feather keys or DIN
5480 involute spline
Tandem seal on the actuator shaft
Because of the almost infinite design possibilities for
the front face almost all connection variants can be
achieved with these actuators.
Fig. 1
Technical data Type DA-H 140
Max. nominal torque at 210 bars
Nm
7100
Max. nominal torque at 210 bars
with camshaft
Nm
6870
Nominal torque
Nm/bar
33,80
bar
210
Max. working pressure *
Max. radial load
N
17800
Max. axial load
N
34800
Auxiliary equipment
Absorption volume
Angle 90°
dm3
0,721
Cushioning at both ends
Angle 180°
dm3
1,439
Rotary angle adjustment up to + 4°
Angle 270°
dm3
2,159
Camshaft
Angle 360°
dm3
2,878
Hollow shaft with DIN 5463, DIN 5480 or Weight
Angle 90°
kg
ca. 74
DIN 6885 profile
Angle 180°
kg
ca. 87
Angle 270°
kg
ca. 101
Special versions
Angle
360°
kg
ca. 115
Actuator shaft with spline profile to DIN
*) Working pressures > 210 bar on request
5463
Actuator shaft with second drive cog
Functional description
Actuator shaft and mounting flange
The oil pressure supplied through connections P1 and P2 causes actuator
designed to customer’s requirements
shaft G to perform a rotary movement. The linear movement of piston K is
Rotary angle adjustment throughout the here converted to a rotary movement by multiple helical gears in the housing,
range of rotation
piston and shaft.
Limit switch equipment
Direct valve connection, 3 mounting
Direction of rotation
positions
All intermediate rotation angles can be With the pressure at P1 actuator shaft G1 rotates from the initial position to
the left (anticlockwise).
supplied
A change in direction of rotation is possible in a special version.
Range of rotation exceeding 360°
-
Sea-water resistant
Additional bearing for high radial forces
Change of direction of rotation
Further special versions are available
Normal position of the feather key:
Figure 1 shows the factory set position of piston K Changes of position are
possible.
TI DA-H 140 - 0606 E
Typical applications
HKS rotary actuators have proved their worth
throughout the industrial sector. For example, they
are used in construction machinery, machine tools,
bending machines, foundry, mining, agricultural and
packing machines, transfer lines, manipulators,
armatures, as well as in shipbuilding, motor vehicles,
assembly platforms and in ventilation engineering.
HKS rotary actuators are reliable and require no
maintenance. This is demonstrated, for example, 2300
mm below sea-level, whey they are used as actuators
for armatures.
Angle of rotation and its adjustment
In the standard version the angle of rotation may be up to 4° in the positive
range. An exact angle of rotation is achieved by means of an additional device
WV.
Cushioning
The speed of rotation of actuator shaft G can be regulated in the limit
positions by throttle check valves. Further information on the subject of
cushioning may be requested on an additional page.
We reserve the right to make modifications
Copyright © 2006 by HKS
Technical informations DA-H 140
Hydraulic rotary actuator
Dimension table
Standard version with feather key
Special version hollow shaft DIN 5463
Special version hollow shaft with feather key grooves (DIN 6885)
Special version angle adjustment
Special version threaded camshaft
Special version with female thread
Special version camshaft with cog
Typ
Am6
DIN 5480*)
B
Ø
Cf7
Ø
D
E
Ø
F
Ø
G
H DIN 6885
I DIN 6885
J DIN 6885
K
L
M
N
O
P
90°
180°
270°
360°
Q
R
90°
180°
270°
360°
S
45°
T
U Number
U
DA-H 140
80
W 80x3x25x8f
250
160
105
187
210
5
140
22
45
220
150
7
10
40
3021,5
401
499
597
78
82
130
180
229
G 1/2"
40°
8
18
Special version HW-hollow shaft to
DIN 5480 on request
B
62
Spline profile DIN 5463
8x52x60
HKS Unternehmensgruppe
Leipziger Straße 53-55
D-63607 Wächtersbach-Aufenau
Phone: +49 (0) 60 53 / 6163 - 0
Extension Const. -11 / Sales. -21
Telefax: +49 (0) 60 53 / 6163 - 39
E-Mail: [email protected]
Internet: www.hks-partner.com
Special version with camshaft
W f7
25
W1 h6
16
Special version with angle
adjustment/camshaft/camshaft
with tapped hole/camshaft with
pivot
P1
90°
334,5
180°
431
270°
529
360°
627
Special version HWP - Hollow shaft
with key grooves (DIN 6885)
H1
120
J1
34,4
CH7
Ø
60
I1P9
18
*) Special version KW spline shaft
DIN is not shown
N.B.: In the hollow shaft version it is
necessary to construct the shaft in a
high strength material. A calculation of
the shaft for torsional strength is
strongly recommended.
We reserve the right to make modifications
Copyright © 2006 by HKS
Technical informations DA-H 160
Hydraulic rotary actuator
General characteristics
Rotary actuators in the DA-H series are characterised
by their performance range. At a working pressure of
up to 210 bars, torques of up to 250,000 Nm are
possible (higher working pressures on request).
Another characteristic is the extremely low angular
clearance.
HKS rotary actuators in the DA-H series offer the
following standards:
-
20 sizes from 36 to 250000 Nm with pistons
Ø 40– Ø 450 mm
4 rotary angle rages for each size: 90°, 180°,
270° and 360°
Actuator shaft with 2 feather keys or DIN
5480 involute spline
Tandem seal on the actuator shaft
Because of the almost infinite design possibilities for
the front face almost all connection variants can be
achieved with these actuators.
Fig. 1
Technical data Type DA-H 160
Max. nominal torque at 210 bars
Nm
11300
Max. nominal torque at 210 bars
with camshaft
Nm
10590
Nominal torque
Nm/bar
53,80
Max. working pressure *
bar
210
Max. radial load
N
36300
Max. axial load
N
46200
Auxiliary equipment
Absorption volume
Angle 90°
dm3
1,063
Cushioning at both ends
Angle 180°
dm3
2,125
Rotary angle adjustment up to + 4°
Angle 270°
dm3
3,188
Camshaft
Angle 360°
dm3
4,251
Hollow shaft with DIN 5463, DIN 5480 or Weight
Angle 90°
kg
ca. 114
DIN 6885 profile
Angle 180°
kg
ca. 136
Angle 270°
kg
ca. 154
Special versions
Angle
360°
kg
ca. 170
Actuator shaft with spline profile to DIN
*) Working pressures > 210 bar on request
5463
Actuator shaft with second drive cog
Functional description
Actuator shaft and mounting flange
The oil pressure supplied through connections P1 and P2 causes actuator
designed to customer’s requirements
shaft G to perform a rotary movement. The linear movement of piston K is
Rotary angle adjustment throughout the here converted to a rotary movement by multiple helical gears in the housing,
range of rotation
piston and shaft.
Limit switch equipment
Direct valve connection, 3 mounting
Direction of rotation
positions
All intermediate rotation angles can be With the pressure at P1 actuator shaft G1 rotates from the initial position to
the left (anticlockwise).
supplied
A change in direction of rotation is possible in a special version.
Range of rotation exceeding 360°
-
Sea-water resistant
Additional bearing for high radial forces
Change of direction of rotation
Further special versions are available
Normal position of the feather key:
Figure 1 shows the factory set position of piston K Changes of position are
possible.
TI DA-H 160 - 0606 E
Typical applications
HKS rotary actuators have proved their worth
throughout the industrial sector. For example, they
are used in construction machinery, machine tools,
bending machines, foundry, mining, agricultural and
packing machines, transfer lines, manipulators,
armatures, as well as in shipbuilding, motor vehicles,
assembly platforms and in ventilation engineering.
HKS rotary actuators are reliable and require no
maintenance. This is demonstrated, for example, 2300
mm below sea-level, whey they are used as actuators
for armatures.
Angle of rotation and its adjustment
In the standard version the angle of rotation may be up to 4° in the positive
range. An exact angle of rotation is achieved by means of an additional device
WV.
Cushioning
The speed of rotation of actuator shaft G can be regulated in the limit
positions by throttle check valves. Further information on the subject of
cushioning may be requested on an additional page.
We reserve the right to make modifications
Copyright © 2006 by HKS
Technical informations DA-H 160
Hydraulic rotary actuator
Dimension table
Standard version with feather key
Special version hollow shaft DIN 5463
Special version hollow shaft with feather key grooves (DIN 6885)
Special version angle adjustment
Special version threaded camshaft
Special version with female thread
Special version camshaft with cog
Typ
Am6
DIN 5480*)
B
Ø
Cf7
Ø
D
E
Ø
F
Ø
G
H DIN 6885
I DIN 6885
J DIN 6885
K
L
M
N
O
P
90°
180°
270°
360°
Q
R
90°
180°
270°
360°
S
45°
T
U Number
U
DA-H 160
100
W 100x3x32x8f
278
190
127
206
240
5
200
28
56
245
210
5
12
43
364
473,5
592,5
707,5
94
110
168
224
281
G 3/4"
40°
8
22
Special version HW-hollow shaft to
DIN 5480 on request
B
82
Spline profile DIN 5463
8x62x72
HKS Unternehmensgruppe
Leipziger Straße 53-55
D-63607 Wächtersbach-Aufenau
Phone: +49 (0) 60 53 / 6163 - 0
Extension Const. -11 / Sales. -21
Telefax: +49 (0) 60 53 / 6163 - 39
E-Mail: [email protected]
Internet: www.hks-partner.com
Special version with camshaft
W f7
40
W1 h6
25
Special version with angle
adjustment/camshaft/camshaft
with tapped hole/camshaft with
pivot
P1
90°
394,5
180°
502,5
270°
621,5
360°
733,5
Special version HWP - Hollow shaft
with key grooves (DIN 6885)
H1
150
J1
42,4
CH7
Ø
75
I1P9
20
*) Special version KW spline shaft
DIN is not shown
N.B.: In the hollow shaft version it is
necessary to construct the shaft in a
high strength material. A calculation of
the shaft for torsional strength is
strongly recommended.
We reserve the right to make modifications
Copyright © 2006 by HKS
Technical informations DA-H 180
Hydraulic rotary actuator
General characteristics
Rotary actuators in the DA-H series are characterised
by their performance range. At a working pressure of
up to 210 bars, torques of up to 250,000 Nm are
possible (higher working pressures on request).
Another characteristic is the extremely low angular
clearance.
HKS rotary actuators in the DA-H series offer the
following standards:
-
20 sizes from 36 to 250000 Nm with pistons
Ø 40– Ø 450 mm
4 rotary angle rages for each size: 90°, 180°,
270° and 360°
Actuator shaft with 2 feather keys or DIN
5480 involute spline
Tandem seal on the actuator shaft
Because of the almost infinite design possibilities for
the front face almost all connection variants can be
achieved with these actuators.
Fig. 1
Technical data Type DA-H 180
Max. nominal torque at 210 bars
Max. nominal torque at 210 bars
with camshaft
Nominal torque
Max. working pressure *
Max. radial load
Max. axial load
Auxiliary equipment
Absorption volume
Angle 90°
Cushioning at both ends
Angle 180°
Rotary angle adjustment up to + 4°
Angle 270°
Camshaft
Angle 360°
Hollow shaft with DIN 5463, DIN 5480 or Weight
Angle 90°
DIN 6885 profile
Angle 180°
Angle 270°
Special versions
Angle 360°
Actuator shaft with spline profile to DIN
*)
Working
pressures
>
210
bar on request
5463
-
Actuator shaft with second drive cog
Actuator shaft and mounting flange
designed to customer’s requirements
Rotary angle adjustment throughout the
range of rotation
Limit switch equipment
Direct valve connection, 3 mounting
positions
All intermediate rotation angles can be
supplied
Range of rotation exceeding 360°
Sea-water resistant
Additional bearing for high radial forces
Change of direction of rotation
Further special versions are available
Nm
16200
Nm
Nm/bar
bar
N
N
dm3
dm3
dm3
dm3
kg
kg
kg
kg
15680
77,14
210
37600
47400
1,607
3,213
4,820
6,427
ca. 150
ca. 187
ca. 213
ca. 245
Functional description
The oil pressure supplied through connections P1 and P2 causes actuator
shaft G to perform a rotary movement. The linear movement of piston K is
here converted to a rotary movement by multiple helical gears in the housing,
piston and shaft.
Direction of rotation
With the pressure at P1 actuator shaft G1 rotates from the initial position to
the left (anticlockwise).
A change in direction of rotation is possible in a special version.
Normal position of the feather key:
Figure 1 shows the factory set position of piston K Changes of position are
possible.
TI DA-H 180 - 0606 E
Typical applications
HKS rotary actuators have proved their worth
throughout the industrial sector. For example, they
are used in construction machinery, machine tools,
bending machines, foundry, mining, agricultural and
packing machines, transfer lines, manipulators,
armatures, as well as in shipbuilding, motor vehicles,
assembly platforms and in ventilation engineering.
HKS rotary actuators are reliable and require no
maintenance. This is demonstrated, for example, 2300
mm below sea-level, whey they are used as actuators
for armatures.
Angle of rotation and its adjustment
In the standard version the angle of rotation may be up to 4° in the positive
range. An exact angle of rotation is achieved by means of an additional device
WV.
Cushioning
The speed of rotation of actuator shaft G can be regulated in the limit
positions by throttle check valves. Further information on the subject of
cushioning may be requested on an additional page.
We reserve the right to make modifications
Copyright © 2006 by HKS
Technical informations DA-H 180
Hydraulic rotary actuator
Dimension table
Standard version with feather key
Special version hollow shaft DIN 5463
Special version hollow shaft with feather key grooves (DIN 6885)
Special version angle adjustment
Special version threaded camshaft
Special version with female thread
Special version camshaft with cog
Typ
Am6
DIN 5480*)
B
Ø
Cf7
Ø
D
E
Ø
F
Ø
G
H DIN 6885
I DIN 6885
J DIN 6885
K
L
M
N
O
P
90°
180°
270°
360°
Q
R
90°
180°
270°
360°
S
45°
T
U Number
U
DA-H 180
105
W 105x3x34x8f
298
210
138
226
270
5
200
28
58,5
265
210
5
12
47
478,5
565
702
880
127
114
186
253
321
G 1"
40°
11
22
Special version HW-hollow shaft to
DIN 5480 on request
B
100
Spline profile DIN 5463
10x72x82
HKS Unternehmensgruppe
Leipziger Straße 53-55
D-63607 Wächtersbach-Aufenau
Phone: +49 (0) 60 53 / 6163 - 0
Extension Const. -11 / Sales. -21
Telefax: +49 (0) 60 53 / 6163 - 39
E-Mail: [email protected]
Internet: www.hks-partner.com
Special version with camshaft
W f7
32
W1 h6
25
Special version with angle
adjustment/camshaft/camshaft
with tapped hole/camshaft with
pivot
P1
90°
475
180°
595
270°
742
360°
900
Special version HWP - Hollow shaft
with key grooves (DIN 6885)
H1
150
J1
42,4
CH7
Ø
75
I1P9
20
*) Special version KW spline shaft
DIN is not shown
N.B.: In the hollow shaft version it is
necessary to construct the shaft in a
high strength material. A calculation of
the shaft for torsional strength is
strongly recommended.
We reserve the right to make modifications
Copyright © 2006 by HKS
Technical informations DA-H 200
Hydraulic rotary actuator
General characteristics
Rotary actuators in the DA-H series are characterised
by their performance range. At a working pressure of
up to 210 bars, torques of up to 250,000 Nm are
possible (higher working pressures on request).
Another characteristic is the extremely low angular
clearance.
HKS rotary actuators in the DA-H series offer the
following standards:
-
20 sizes from 36 to 250000 Nm with pistons
Ø 40– Ø 450 mm
4 rotary angle rages for each size: 90°, 180°,
270° and 360°
Actuator shaft with 2 feather keys or DIN
5480 involute spline
Tandem seal on the actuator shaft
Because of the almost infinite design possibilities for
the front face almost all connection variants can be
achieved with these actuators.
Fig. 1
Technical data Type DA-H 200
Max. nominal torque at 210 bars
Max. nominal torque at 210 bars
with camshaft
Nominal torque
Max. working pressure *
Max. radial load
Max. axial load
Auxiliary equipment
Absorption volume
Angle 90°
Cushioning at both ends
Angle 180°
Rotary angle adjustment up to + 4°
Angle 270°
Camshaft
Angle 360°
Hollow shaft with DIN 5463, DIN 5480 or
Weight
Angle 90°
DIN 6885 profile
Angle 180°
Angle 270°
Special versions
Angle 360°
Actuator shaft with spline profile to DIN
*)
Working
pressures
>
210
bar on request
5463
-
Actuator shaft with second drive cog
Actuator shaft and mounting flange
designed to customer’s requirements
Rotary angle adjustment throughout the
range of rotation
Limit switch equipment
Direct valve connection, 3 mounting
positions
All intermediate rotation angles can be
supplied
Range of rotation exceeding 360°
Sea-water resistant
Additional bearing for high radial forces
Change of direction of rotation
Further special versions are available
Nm
22300
Nm
Nm/bar
bar
N
N
dm3
dm3
dm3
dm3
kg
kg
kg
kg
21400
106,20
210
67210
62000
2,147
4,294
6,441
8,588
ca. 194
ca. 238
ca. 264
ca. 306
Functional description
The oil pressure supplied through connections P1 and P2 causes actuator
shaft G to perform a rotary movement. The linear movement of piston K is
here converted to a rotary movement by multiple helical gears in the housing,
piston and shaft.
Direction of rotation
With the pressure at P1 actuator shaft G1 rotates from the initial position to
the left (anticlockwise).
A change in direction of rotation is possible in a special version.
Normal position of the feather key:
Figure 1 shows the factory set position of piston K Changes of position are
possible.
TI DA-H 200 - 0606 E
Typical applications
HKS rotary actuators have proved their worth
throughout the industrial sector. For example, they
are used in construction machinery, machine tools,
bending machines, foundry, mining, agricultural and
packing machines, transfer lines, manipulators,
armatures, as well as in shipbuilding, motor vehicles,
assembly platforms and in ventilation engineering.
HKS rotary actuators are reliable and require no
maintenance. This is demonstrated, for example, 2300
mm below sea-level, whey they are used as actuators
for armatures.
Angle of rotation and its adjustment
In the standard version the angle of rotation may be up to 4° in the positive
range. An exact angle of rotation is achieved by means of an additional device
WV.
Cushioning
The speed of rotation of actuator shaft G can be regulated in the limit
positions by throttle check valves. Further information on the subject of
cushioning may be requested on an additional page.
We reserve the right to make modifications
Copyright © 2006 by HKS
Technical informations DA-H 200
Hydraulic rotary actuator
Dimension table
Standard version with feather key
Special version hollow shaft DIN 5463
Special version hollow shaft with feather key grooves (DIN 6885)
Special version angle adjustment
Special version threaded camshaft
Special version with female thread
Special version camshaft with cog
Typ
Am6
DIN 5480*)
B
Ø
Cf7
Ø
D
E
Ø
F
Ø
G
H DIN 6885
I DIN 6885
J DIN 6885
K
L
M
N
O
P
90°
180°
270°
360°
Q
R
90°
180°
270°
360°
S
45°
T
U Number
U
DA-H 200
140
W 120x5x22x8f
325
235
150
255
295
5
200
32
67
290
210
4
10
54
438,5
584,5
725,5
876,5
125
125
196
265,5
340
G 1"
30°
11
22
Special version HW-hollow shaft to
DIN 5480 on request
B
100
Spline profile DIN 5463
10x82x92
HKS Unternehmensgruppe
Leipziger Straße 53-55
D-63607 Wächtersbach-Aufenau
Phone: +49 (0) 60 53 / 6163 - 0
Extension Const. -11 / Sales. -21
Telefax: +49 (0) 60 53 / 6163 - 39
E-Mail: [email protected]
Internet: www.hks-partner.com
Special version with camshaft
W f7
40
W1 h6
25
Special version with angle
adjustment/camshaft/camshaft
with tapped hole/camshaft with
pivot
P1
90°
478,5
180°
632,5
270°
765,5
360°
914,5
Special version HWP - Hollow shaft
with key grooves (DIN 6885)
H1
175
J1
52,9
CH7
Ø
95
I1P9
25
*) Special version KW spline shaft
DIN is not shown
N.B.: In the hollow shaft version it is
necessary to construct the shaft in a
high strength material. A calculation of
the shaft for torsional strength is
strongly recommended.
We reserve the right to make modifications
Copyright © 2006 by HKS
Technical informations DA-H 225
Hydraulic rotary actuator
General characteristics
Rotary actuators in the DA-H series are characterised
by their performance range. At a working pressure of
up to 210 bars, torques of up to 250,000 Nm are
possible (higher working pressures on request).
Another characteristic is the extremely low angular
clearance.
HKS rotary actuators in the DA-H series offer the
following standards:
-
20 sizes from 36 to 250000 Nm with pistons
Ø 40– Ø 450 mm
4 rotary angle rages for each size: 90°, 180°,
270° and 360°
Actuator shaft with 2 feather keys or DIN
5480 involute spline
Tandem seal on the actuator shaft
Because of the almost infinite design possibilities for
the front face almost all connection variants can be
achieved with these actuators.
Fig. 1
Technical data Type DA-H 225
Max. nominal torque at 210 bars
Nm
Max. nominal torque at 210 bars
with camshaft
Nm
Nominal torque
Nm/bar
Max. working pressure *
bar
Max. radial load
N
Max. axial load
N
Auxiliary equipment
Absorption volume
Angle 90°
dm3
Cushioning at both ends
Angle 180°
dm3
Rotary angle adjustment up to + 4°
Angle 270°
dm3
Camshaft
Angle 360°
dm3
Hollow shaft with DIN 5463, DIN 5480 or
Weight
Winkel 90°
kg
DIN 6885 profile
Angle 180°
kg
Angle
270°
kg
Special versions
Angle
360°
kg
Actuator shaft with spline profile to DIN
*)
Working
pressures
>
210
bar
on
request
5463
-
Actuator shaft with second drive cog
Actuator shaft and mounting flange
designed to customer’s requirements
Rotary angle adjustment throughout the
range of rotation
Limit switch equipment
Direct valve connection, 3 mounting
positions
All intermediate rotation angles can be
supplied
Range of rotation exceeding 360°
Sea-water resistant
Additional bearing for high radial forces
Change of direction of rotation
Further special versions are available
32000
30980
152,38
210
69000
63100
3,178
6,346
9,522
12,695
ca. 404
ca. 488
ca. 565
ca. 630
Functional description
The oil pressure supplied through connections P1 and P2 causes actuator
shaft G to perform a rotary movement. The linear movement of piston K is
here converted to a rotary movement by multiple helical gears in the housing,
piston and shaft.
Direction of rotation
With the pressure at P1 actuator shaft G1 rotates from the initial position to
the left (anticlockwise).
A change in direction of rotation is possible in a special version.
Normal position of the feather key:
Figure 1 shows the factory set position of piston K Changes of position are
possible.
TI DA-H 225 - 0606 E
Typical applications
HKS rotary actuators have proved their worth
throughout the industrial sector. For example, they
are used in construction machinery, machine tools,
bending machines, foundry, mining, agricultural and
packing machines, transfer lines, manipulators,
armatures, as well as in shipbuilding, motor vehicles,
assembly platforms and in ventilation engineering.
HKS rotary actuators are reliable and require no
maintenance. This is demonstrated, for example, 2300
mm below sea-level, whey they are used as actuators
for armatures.
Angle of rotation and its adjustment
In the standard version the angle of rotation may be up to 4° in the positive
range. An exact angle of rotation is achieved by means of an additional device
WV.
Cushioning
The speed of rotation of actuator shaft G can be regulated in the limit
positions by throttle check valves. Further information on the subject of
cushioning may be requested on an additional page.
We reserve the right to make modifications
Copyright © 2006 by HKS
Technical informations DA-H 225
Hydraulic rotary actuator
Dimension table
Standard version with feather key
Special version hollow shaft DIN 5463
Special version hollow shaft with feather key grooves (DIN 6885)
Special version angle adjustment
Special version threaded camshaft
Special version with female thread
Special version camshaft with cog
Typ
Am6
DIN 5480*)
B
Ø
Cf7
Ø
D
E
Ø
F
Ø
G
H DIN 6885
I DIN 6885
J DIN 6885
K
L
M
N
O
P
90°
180°
270°
360°
Q
R
90°
180°
270°
360°
S
45°
T
U Number
U
DA-H 225
140
W 120x5x26x8f
385
260
224
300
350
5
250
36
78
345
260
6
15
64
570
732
900
1069
155
159
240
321
403
G 1"
22,5°
15
22
Special version HW-hollow shaft to
DIN 5480 on request
B
120
Spline profile DIN 5463 10x92x102
HKS Unternehmensgruppe
Leipziger Straße 53-55
D-63607 Wächtersbach-Aufenau
Phone: +49 (0) 60 53 / 6163 - 0
Extension Const. -11 / Sales. -21
Telefax: +49 (0) 60 53 / 6163 - 39
E-Mail: [email protected]
Internet: www.hks-partner.com
Special version with camshaft
W f7
40
W1 h6
25
Special version with angle
adjustment/camshaft/camshaft
with tapped hole/camshaft with
pivot
P1
90°
645
180°
807
270°
975
360°
1140
Special version HWP - Hollow shaft
with key grooves (DIN 6885)
H1
175
J1
56,4
CH7
Ø
100
I1 P9
28
*) Special version KW spline shaft
DIN is not shown
N.B.: In the hollow shaft version it is
necessary to construct the shaft in a
high strength material. A calculation of
the shaft for torsional strength is
strongly recommended.
We reserve the right to make modifications
Copyright © 2006 by HKS
Technical informations DA-H 225 S
Hydraulic rotary actuator
General characteristics
Rotary actuators in the DA-H series are characterised
by their performance range. At a working pressure of
up to 210 bars, torques of up to 250,000 Nm are
possible (higher working pressures on request).
Another characteristic is the extremely low angular
clearance.
HKS rotary actuators in the DA-H series offer the
following standards:
-
20 sizes from 36 to 250000 Nm with pistons
Ø 40– Ø 450 mm
4 rotary angle rages for each size: 90°, 180°,
270° and 360°
Actuator shaft with 2 feather keys or DIN
5480 involute spline
Tandem seal on the actuator shaft
Because of the almost infinite design possibilities for
the front face almost all connection variants can be
achieved with these actuators.
Auxiliary equipment
Cushioning at both ends
Rotary angle adjustment up to + 4°
Camshaft
Hollow shaft with DIN 5463, DIN 5480 or
DIN 6885 profile
Special versions
Actuator shaft with spline profile to DIN
5463
Actuator shaft with second drive cog
Actuator shaft and mounting flange
designed to customer’s requirements
Rotary angle adjustment throughout the
range of rotation
Limit switch equipment
Direct valve connection, 3 mounting
positions
All intermediate rotation angles can be
supplied
Range of rotation exceeding 360°
Sea-water resistant
Additional bearing for high radial forces
Change of direction of rotation
Further special versions are available
Fig. 1
Technical data Type DA-H 225 S
Max. nominal torque at 210 bars
Max. nominal torque at 210 bars
with camshaft
Nominal torque
Max. working pressure *
Max. radial load
Max. axial load
Absorption volume
Angle 90°
Angle 180°
Angle 270°
Angle 360°
Weight
Angle 90°
Angle 180°
Angle 270°
Angle 360°
*) Working pressures > 210 bar on request
Nm
38920
Nm
Nm/bar
bar
N
N
dm3
dm3
dm3
dm3
kg
kg
kg
kg
37690
185,33
210
69000
63100
4,127
8,245
12,368
16,491
ca. 487
ca. 543
ca. 637
ca. 684
Functional description
The oil pressure supplied through connections P1 and P2 causes actuator
shaft G to perform a rotary movement. The linear movement of piston K is
here converted to a rotary movement by multiple helical gears in the housing,
piston and shaft.
Direction of rotation
With the pressure at P1 actuator shaft G1 rotates from the initial position to
the left (anticlockwise).
A change in direction of rotation is possible in a special version.
Normal position of the feather key:
Figure 1 shows the factory set position of piston K Changes of position are
possible.
TI DA-H 225S - 0606 E
Typical applications
HKS rotary actuators have proved their worth
throughout the industrial sector. For example, they
are used in construction machinery, machine tools,
bending machines, foundry, mining, agricultural and
packing machines, transfer lines, manipulators,
armatures, as well as in shipbuilding, motor vehicles,
assembly platforms and in ventilation engineering.
HKS rotary actuators are reliable and require no
maintenance. This is demonstrated, for example, 2300
mm below sea-level, whey they are used as actuators
for armatures.
Angle of rotation and its adjustment
In the standard version the angle of rotation may be up to 4° in the positive
range. An exact angle of rotation is achieved by means of an additional device
WV.
Cushioning
The speed of rotation of actuator shaft G can be regulated in the limit
positions by throttle check valves. Further information on the subject of
cushioning may be requested on an additional page.
We reserve the right to make modifications
Copyright © 2006 by HKS
Technical informations DA-H 225 S
Hydraulic rotary actuator
Dimension table
Standard version with feather key
Special version hollow shaft DIN 5463
Special version hollow shaft with feather key grooves (DIN 6885)
Special version angle adjustment
Special version threaded camshaft
Special version with female thread
Special version camshaft with cog
Typ
Am6
DIN 5480*)
B
Ø
Cf7
Ø
D
E
Ø
F
Ø
G
H DIN 6885
I DIN 6885
J DIN 6885
K
L
M
N
O
P
90°
180°
270°
360°
Q
R
90°
180°
270°
360°
S
45°
T
U Number
U
DA-H 225 S
140
W 140x5x26x8f
385
260
224
300
350
5
250
36
78
345
260
6
15
64
690
805
995
1220
155
175
276
381
484
G 1"
22,5°
15
22
Special version HW-hollow shaft to
DIN 5480 on request
B
120
Spline profile DIN 5463 10x92x102
HKS Unternehmensgruppe
Leipziger Straße 53-55
D-63607 Wächtersbach-Aufenau
Phone: +49 (0) 60 53 / 6163 - 0
Extension Const. -11 / Sales. -21
Telefax: +49 (0) 60 53 / 6163 - 39
E-Mail: [email protected]
Internet: www.hks-partner.com
Special version with camshaft
W f7
40
W1 h6
25
Special version with angle
adjustment/camshaft/camshaft
with tapped hole/camshaft with
pivot
P1
90°
765
180°
880
270°
1070
360°
1295
Special version HWP - Hollow shaft
with key grooves (DIN 6885)
H1
175
J1
56,4
CH7
Ø
100
I1P9
28
*) Special version KW spline shaft
DIN is not shown
N.B.: In the hollow shaft version it is
necessary to construct the shaft in a
high strength material. A calculation of
the shaft for torsional strength is
strongly recommended.
We reserve the right to make modifications
Copyright © 2006 by HKS
Technical informations DA-H 250
Hydraulic rotary actuator
General characteristics
Rotary actuators in the DA-H series are characterised
by their performance range. At a working pressure of
up to 210 bars, torques of up to 250,000 Nm are
possible (higher working pressures on request).
Another characteristic is the extremely low angular
clearance.
HKS rotary actuators in the DA-H series offer the
following standards:
-
20 sizes from 36 to 250000 Nm with pistons
Ø 40– Ø 450 mm
4 rotary angle rages for each size: 90°, 180°,
270° and 360°
Actuator shaft with 2 feather keys or DIN
5480 involute spline
Tandem seal on the actuator shaft
Because of the almost infinite design possibilities for
the front face almost all connection variants can be
achieved with these actuators.
Auxiliary equipment
Cushioning at both ends
Rotary angle adjustment up to + 4°
Camshaft
Hollow shaft with DIN 5463, DIN 5480 or
DIN 6885 profile
Special versions
Actuator shaft with spline profile to DIN
5463
Actuator shaft with second drive cog
Actuator shaft and mounting flange
designed to customer’s requirements
Rotary angle adjustment throughout the
range of rotation
Limit switch equipment
Direct valve connection, 3 mounting
positions
All intermediate rotation angles can be
supplied
Range of rotation exceeding 360°
Sea-water resistant
Additional bearing for high radial forces
Change of direction of rotation
Further special versions are available
Fig. 1
Technical data Type DA-H 250
Max. nominal torque at 210 bars
Max. nominal torque at 210 bars
with camshaft
Nominal torque
Max. working pressure *
Max. radial load
Max. axial load
Absorption volume
Angle 90°
Angle 180°
Angle 270°
Angle 360°
Weight
Angle 90°
Angle 180°
Angle 270°
Angle 360°
*) Working pressures > 210 bar on request
Nm
Nm
Nm/bar
bar
N
N
dm3
dm3
dm3
dm3
kg
kg
kg
kg
44000
42870
209,52
210
78000
66500
4,490
8,980
13,470
17,959
ca. 630
ca. 726
ca. 815
ca. 912
Functional description
The oil pressure supplied through connections P1 and P2 causes actuator
shaft G to perform a rotary movement. The linear movement of piston K is
here converted to a rotary movement by multiple helical gears in the housing,
piston and shaft.
Direction of rotation
With the pressure at P1 actuator shaft G1 rotates from the initial position to
the left (anticlockwise).
A change in direction of rotation is possible in a special version.
Normal position of the feather key:
Figure 1 shows the factory set position of piston K Changes of position are
possible.
TI DA-H 250 - 0606 E
Typical applications
HKS rotary actuators have proved their worth
throughout the industrial sector. For example, they
are used in construction machinery, machine tools,
bending machines, foundry, mining, agricultural and
packing machines, transfer lines, manipulators,
armatures, as well as in shipbuilding, motor vehicles,
assembly platforms and in ventilation engineering.
HKS rotary actuators are reliable and require no
maintenance. This is demonstrated, for example, 2300
mm below sea-level, whey they are used as actuators
for armatures.
Angle of rotation and its adjustment
In the standard version the angle of rotation may be up to 4° in the positive
range. An exact angle of rotation is achieved by means of an additional device
WV.
Cushioning
The speed of rotation of actuator shaft G can be regulated in the limit
positions by throttle check valves. Further information on the subject of
cushioning may be requested on an additional page.
We reserve the right to make modifications
Copyright © 2006 by HKS
Technical informations DA-H 250
Hydraulic rotary actuator
Dimension table
Standard version with feather key
Special version hollow shaft DIN 5463
Special version hollow shaft with feather key grooves (DIN 6885)
Special version angle adjustment
Special version threaded camshaft
Special version with female thread
Special version camshaft with cog
Typ
Am6
DIN 5480*)
B
Ø
Cf7
Ø
D
E
Ø
F
Ø
G
H DIN 6885
I DIN 6885
J DIN 6885
K
L
M
N
O
P
90°
180°
270°
360°
Q
R
90°
180°
270°
360°
S
45°
T
U Number
U
DA-H 250
150
W 150x5x28x8f
450
300
240
346
385
10
280
36
83
400
300
6
20
90
710
875
1060
1261
224
155
248
343
437
G 1"
22,5°
15
26
Special version HW-hollow shaft to
DIN 5480 on request
B
120
Spline profile DIN 5463 10x102x112
HKS Unternehmensgruppe
Leipziger Straße 53-55
D-63607 Wächtersbach-Aufenau
Phone: +49 (0) 60 53 / 6163 - 0
Extension Const. -11 / Sales. -21
Telefax: +49 (0) 60 53 / 6163 - 39
E-Mail: [email protected]
Internet: www.hks-partner.com
Special version with camshaft
W f7
40
W1 h6
25
Special version with angle
adjustment/camshaft/camshaft
with tapped hole/camshaft with
pivot
P1
90°
725
180°
910
270°
1095
360°
1286
Special version HWP - Hollow shaft
with key grooves (DIN 6885)
H1
175
J1
61,4
CH7
Ø
110
I1P9
28
*) Special version KW spline shaft
DIN is not shown
N.B.: In the hollow shaft version it is
necessary to construct the shaft in a
high strength material. A calculation of
the shaft for torsional strength is
strongly recommended.
We reserve the right to make modifications
Copyright © 2006 by HKS
Technical informations DA-H 280
Hydraulic rotary actuator
General characteristics
Rotary actuators in the DA-H series are characterised
by their performance range. At a working pressure of
up to 210 bars, torques of up to 250,000 Nm are
possible (higher working pressures on request).
Another characteristic is the extremely low angular
clearance.
HKS rotary actuators in the DA-H series offer the
following standards:
-
20 sizes from 36 to 250000 Nm with pistons
Ø 40– Ø 450 mm
4 rotary angle rages for each size: 90°, 180°,
270° and 360°
Actuator shaft with 2 feather keys or DIN
5480 involute spline
Tandem seal on the actuator shaft
Because of the almost infinite design possibilities for
the front face almost all connection variants can be
achieved with these actuators.
Auxiliary equipment
Cushioning at both ends
Rotary angle adjustment up to + 4°
Camshaft
Hollow shaft with DIN 5463, DIN 5480 or
DIN 6885 profile
Special versions
Actuator shaft with spline profile to DIN
5463
Actuator shaft with second drive cog
Actuator shaft and mounting flange
designed to customer’s requirements
Rotary angle adjustment throughout the
range of rotation
Limit switch equipment
Direct valve connection, 3 mounting
positions
All intermediate rotation angles can be
supplied
Range of rotation exceeding 360°
Sea-water resistant
Additional bearing for high radial forces
Change of direction of rotation
Further special versions are available
Fig. 1
Technical data Type DA-H 280
Max. nominal torque at 210 bars
Max. nominal torque at 210 bars
with camshaft
Nominal torque
Max. working pressure *
Max. radial load
Max. axial load
Absorption volume
Angle 90°
Angle 180°
Angle 270°
Angle 360°
Weight
Angle 90°
Angle 180°
Angle 270°
Angle 360°
*) Working pressures > 210 bar on request
Nm
60800
Nm
Nm/bar
bar
N
N
dm3
dm3
dm3
dm3
kg
kg
kg
kg
59580
289,52
210
84600
71000
6,221
12,442
18,664
24,885
ca. 874
ca. 1011
ca. 1164
ca. 1292
Functional description
The oil pressure supplied through connections P1 and P2 causes actuator
shaft G to perform a rotary movement. The linear movement of piston K is
here converted to a rotary movement by multiple helical gears in the housing,
piston and shaft.
Direction of rotation
With the pressure at P1 actuator shaft G1 rotates from the initial position to
the left (anticlockwise).
A change in direction of rotation is possible in a special version.
Normal position of the feather key:
Figure 1 shows the factory set position of piston K Changes of position are
possible.
TI DA-H 280 - 0606 E
Typical applications
HKS rotary actuators have proved their worth
throughout the industrial sector. For example, they
are used in construction machinery, machine tools,
bending machines, foundry, mining, agricultural and
packing machines, transfer lines, manipulators,
armatures, as well as in shipbuilding, motor vehicles,
assembly platforms and in ventilation engineering.
HKS rotary actuators are reliable and require no
maintenance. This is demonstrated, for example, 2300
mm below sea-level, whey they are used as actuators
for armatures.
Angle of rotation and its adjustment
In the standard version the angle of rotation may be up to 4° in the positive
range. An exact angle of rotation is achieved by means of an additional device
WV.
Cushioning
The speed of rotation of actuator shaft G can be regulated in the limit
positions by throttle check valves. Further information on the subject of
cushioning may be requested on an additional page.
We reserve the right to make modifications
Copyright © 2006 by HKS
Technical informations DA-H 280
Hydraulic rotary actuator
Dimension table
Standard version with feather key
Special version hollow shaft DIN 5463
Special version hollow shaft with feather key grooves (DIN 6885)
Special version angle adjustment
Special version threaded camshaft
Special version with female thread
Special version camshaft with cog
Typ
Am6
DIN 5480*)
B
Ø
Cf7
Ø
D
E
Ø
F
Ø
G
H DIN 6885
I DIN 6885
J DIN 6885
K
L
M
N
O
P
90°
180°
270°
360°
Q
R
90°
180°
270°
360°
S
45°
T
U Number
U
DA-H 280
170
W 170x5x32x8f
490
340
266
394
435
10
280
40
94
450
300
6
20
100
790
1000
1205
1408
261
183
287
392
493
G 1"
18°
19
26
Special version HW-hollow shaft to
DIN 5480 on request
B
130
Spline profile DIN 5463 10x112x125
HKS Unternehmensgruppe
Leipziger Straße 53-55
D-63607 Wächtersbach-Aufenau
Phone: +49 (0) 60 53 / 6163 - 0
Extension Const. -11 / Sales. -21
Telefax: +49 (0) 60 53 / 6163 - 39
E-Mail: [email protected]
Internet: www.hks-partner.com
Special version with camshaft
W f7
40
W1 h6
25
Special version with angle
adjustment/camshaft/camshaft
with tapped hole/camshaft with
pivot
P1
90°
865
180°
1075
270°
1280
360°
1483
Special version HWP - Hollow shaft
with key grooves (DIN 6885)
H1
200
J1
67,4
CH7
Ø
120
I1P9
32
*) Special version KW spline shaft
DIN is not shown
N.B.: In the hollow shaft version it is
necessary to construct the shaft in a
high strength material. A calculation of
the shaft for torsional strength is
strongly recommended.
We reserve the right to make modifications
Copyright © 2006 by HKS
Technical informations DA-H 300
Hydraulic rotary actuator
General characteristics
Rotary actuators in the DA-H series are characterised
by their performance range. At a working pressure of
up to 210 bars, torques of up to 250,000 Nm are
possible (higher working pressures on request).
Another characteristic is the extremely low angular
clearance.
HKS rotary actuators in the DA-H series offer the
following standards:
-
20 sizes from 36 to 250000 Nm with pistons
Ø 40– Ø 450 mm
4 rotary angle rages for each size: 90°, 180°,
270° and 360°
Actuator shaft with 2 feather keys or DIN
5480 involute spline
Tandem seal on the actuator shaft
Because of the almost infinite design possibilities for
the front face almost all connection variants can be
achieved with these actuators.
Auxiliary equipment
Cushioning at both ends
Rotary angle adjustment up to + 4°
Camshaft
Hollow shaft with DIN 5463, DIN 5480 or
DIN 6885 profile
Special versions
Actuator shaft with spline profile to DIN
5463
Actuator shaft with second drive cog
Actuator shaft and mounting flange
designed to customer’s requirements
Rotary angle adjustment throughout the
range of rotation
Limit switch equipment
Direct valve connection, 3 mounting
positions
All intermediate rotation angles can be
supplied
Range of rotation exceeding 360°
Sea-water resistant
Additional bearing for high radial forces
Change of direction of rotation
Further special versions are available
Fig. 1
Technical data Type DA-H 300
Max. nominal torque at 210 bars
Max. nominal torque at 210 bars
with camshaft
Nominal torque
Max. working pressure *
Max. radial load
Max. axial load
Absorption volume
Angle 90°
Angle 180°
Angle 270°
Angle 360°
Weight
Angle 90°
Angle 180°
Angle 270°
Angle 360°
*) Working pressures > 210 bar on request
Nm
76000
Nm
Nm/bar
bar
N
N
dm3
dm3
dm3
dm3
kg
kg
kg
kg
74630
361,9
210
89400
76000
7,792
15,584
23,376
31,168
ca. 1126
ca. 1308
ca. 1489
ca. 1677
Functional description
The oil pressure supplied through connections P1 and P2 causes actuator
shaft G to perform a rotary movement. The linear movement of piston K is
here converted to a rotary movement by multiple helical gears in the housing,
piston and shaft.
Direction of rotation
With the pressure at P1 actuator shaft G1 rotates from the initial position to
the left (anticlockwise).
A change in direction of rotation is possible in a special version.
Normal position of the feather key:
Figure 1 shows the factory set position of piston K Changes of position are
possible.
TI DA-H 300 - 0606 E
Typical applications
HKS rotary actuators have proved their worth
throughout the industrial sector. For example, they
are used in construction machinery, machine tools,
bending machines, foundry, mining, agricultural and
packing machines, transfer lines, manipulators,
armatures, as well as in shipbuilding, motor vehicles,
assembly platforms and in ventilation engineering.
HKS rotary actuators are reliable and require no
maintenance. This is demonstrated, for example, 2300
mm below sea-level, whey they are used as actuators
for armatures.
Angle of rotation and its adjustment
In the standard version the angle of rotation may be up to 4° in the positive
range. An exact angle of rotation is achieved by means of an additional device
WV.
Cushioning
The speed of rotation of actuator shaft G can be regulated in the limit
positions by throttle check valves. Further information on the subject of
cushioning may be requested on an additional page.
We reserve the right to make modifications
Copyright © 2006 by HKS
Technical informations DA-H 300
Hydraulic rotary actuator
Dimension table
Standard version with feather key
Special version hollow shaft DIN 5463
Special version hollow shaft with feather key grooves (DIN 6885)
Special version threaded camshaft
Special version angle adjustment
Special version with female thread
Typ
Am6
DIN 5480*)
B
Ø
Cf7
Ø
D
E
Ø
F
Ø
G
H DIN 6885
I DIN 6885
J DIN 6885
K
L
M
N
O
P
90°
180°
270°
360°
Q
R
90°
180°
270°
360°
S
45°
T
U Number
U
DA-H 300
180
W 180x5x34x8f
555
380
285
440
470
10
280
45
100
500
300
6
20
110
840
1060
1285
1510
271
194
302
414
528
G 1“
18°
19
32
Special version camshaft with cog
Special version HW-hollow shaft to
DIN 5480 on request
B
140
Spline profile DIN 5472 130x145x24
HKS Unternehmensgruppe
Leipziger Straße 53-55
D-63607 Wächtersbach-Aufenau
Phone: +49 (0) 60 53 / 6163 - 0
Extension Const. -11 / Sales. -21
Telefax: +49 (0) 60 53 / 6163 - 39
E-Mail: [email protected]
Internet: www.hks-partner.com
Special version with camshaft
W f7
40
W1 h6
25
Special version with angle
adjustment/camshaft/camshaft
with tapped hole/camshaft with
pivot
P1
90°
930
180°
1150
270°
1375
360°
1600
Special version HWP - Hollow shaft
with key grooves (DIN 6885)
H1
200
J1
78,4
CH7
Ø
140
I1P9
36
*) Special version KW spline shaft
DIN is not shown
N.B.: In the hollow shaft version it is
necessary to construct the shaft in a
high strength material. A calculation of
the shaft for torsional strength is
strongly recommended.
We reserve the right to make modifications
Copyright © 2006 by HKS