victor Application Server Introduction

Transcription

victor Application Server Introduction
victor unified client
victor Application Server
Administration/
Configuration Guide
version 4.5
8200-1069-01 A0
Notice
The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products. All
specifications are therefore subject to change without notice.
Copyright
Under copyright laws, the contents of this manual may not be copied, photocopied, reproduced, translated or reduced to any electronic
medium or machine-readable form, in whole or in part, without prior written consent of Tyco Security Products.
© 2014 Tyco Security Products. All Rights Reserved.
American Dynamics
60 Congress Avenue
Boca Raton, FL 33487 U.S.A.
Customer Service
Thanks you for using American Dynamics products. We support our products through an extensive worldwide network of dealers. the dealer
through whom you originally purchased this product is your point of contact if you need service or support. Our dealers are empowered to
provide the very best in customer service and support. Dealers should contact American Dynamics at (800) 507-6268 or (561) 912-6259 or
on the Web at www.americandynamics.net.
Trademarks
Windows® is a registered trademark of Microsoft Corporation. PS/2® is a registered trademark of International Business Machines
Corporation.
The trademarks, logos, and service marks displayed on this document are registered in the United States [or other countries]. Any misuse of
the trademarks is strictly prohibited and Tyco Security Products. will aggressively enforce its intellectual property rights to the fullest extent of
the law, including pursuit of criminal prosecution wherever necessary. All trademarks not owned by Tyco Security Products are the property
of their respective owners, and are used with permission or allowed under applicable laws.
Product offerings and specifications are subject to change without notice. Actual products may vary from photos. Not all products include all
features. Availability varies by region; contact your sales representative.
License Information
Your use of this product is governed by certain terms and conditions. Please see the detailed license information at the end of this manual.
240414
2
Overview
About this document
This help document is primarily designed for System Administrators and users with victor configuration privileges.
Only suitably trained personnel should attempt victor installation and configuration tasks.
For basic user functionality, refer to the separate victor operator help documentation.
victor
victor is part of a powerful Network Video Management System (NVMS) that includes advanced policy management,
health monitoring, Smart Search, instant playback, and more, ensuring the security and safety of your entire
organization whether a single site, or a multi-location, globally dispersed enterprise.
victor Express
As part of the victor unified client portfolio, victor Express offers the ability to manage video from multiple Intellex, and
VideoEdge NVR/Hybrid recorders from a single intuitive interface.
By removing the victor Application Server requirement which provides more enterprise functionality victor Express
utilizes SQL Express Localdb to provide single site applications a powerful way to manage multiple recorders.
Unified Solution
Unification with Software House C·CURE 9000 access control system provides multi-dimensional single-point event
management. Refer to www.americandynamics.net for further information.
Components
victor unified client
victor unifies security, surveillance, and event management. From a single interface, you can manage live/recorded
video from Intellex DVRs, VideoEdge NVRs, ADTVRs and HDVR hybrid recorders.
Unified with Software House C·CURE 9000 access control system, victor provides single-point event management
across both systems.
victor is designed to handle the high throughput of HD and megapixel cameras and manage real-time alarms and
events. The victor solution scales from a single site to multi-location global deployments and simplifies management
of large, geographically dispersed security operations.
The victor solution includes advanced policy management, health monitoring, Smart Search, instant playback, and
more, ensuring the security and safety of your entire organization. Analog and IP video and cameras can be displayed
simultaneously, all with a common feature set, no matter what the codec (H.264, ACC, MJPEG, MPEG-4) allowing
you to mix and match technologies without toggling between separate client applications.
The intuitive design includes advanced features such as tear off, snap, auto hide, tab, and dock windows, providing an
easy and customizable operator experience.
3
An easy-to-use tree structure puts everything at your fingertips. Create and organize camera lists from multiple
Intellex, HDVR, and VideoEdge recorders (any camera from any recorder) to meet the needs of different operators.
Build video tours, salvos, and saved views, then organize them into victor's customizable and easy-to-use site lists
for rapid response.
Motion-based Smart Searches are run on a database of meta-data instead of searching through hours or weeks of
video. This makes incident investigations incredibly fast and easy. Add advanced video analytics to your VideoEdge
NVRs to increase situational awareness with alarms for trip wire, linger, object removed/abandoned and more.
victor Application Server (Server)
The victor Application Server is the brains of the operation - storing data, operator profiles, roles, camera/recorder
information and access controls objects.
Dual modes of user authentication allows users to log in using Active Directory credentials or via a ‘Basic’ method
which does not require a domain controller.
Also, using Microsoft Active Directory, operator profiles can be tied to are portable which allows users to move from
one victor client to another as their credentials follow them, regardless of the PC.
Restrict what devices and features an operator can access by assigning roles using victor's included policy
management. Permissions can be set system wide for a specific camera.
Any feature can be limited and updated as situations warrant. victor also journals and tracks what has happened on
your systems, such as operator activities, search and export history, creating an audit trail.
victor player
victor player is the standalone video player application which can be exported along with digitally-verified video clips to
enable the playback of exported video clips in native format without requiring the full installation of the client.
victor Command Center
The victor Command Center lets you build your own security operation center (SOC). You can manage thousands of
cameras and multiple locations, creating video walls using standard PCs. Video walls are a key component to
monitoring large camera counts. Share and communicate information between operators and pushing live or recorded
video from one monitor to another - to ensure rapid response to critical events. You can expand your system by adding
victor client and agent licenses, to meet the needs of your organization.
victor/C·CURE Unification
victor/C·CURE 9000 unification provides advanced, seamless integration between victor and C·CURE 9000
standalone platforms, allowing users of victor unified client to monitor C·CURE devices and events from within the
victor environment.
Note:
Version Compatibility - C·CURE 9000 Integration requires: C·CURE 9000 v2.1+ and victor v4.2+ Refer to the victor
and C·CURE Unification Guide for further information.
4
MAS/SAS Support: Overview
For customers with large, dispersed systems, victor supports enterprise level Master Application Server/Satellite
Application Server (MAS/SAS) deployment.
Enterprise Architecture provides you the ability to view and manage all aspects of access control and video security
from one application - the Administration Workstation attached to the MAS.
MAS/SAS architecture functions by synchronizing each SAS system's database with the MAS database. The Master
(MAS) contains the global data that is used across every server, such as global Personnel records, global clearances,
and global Operators. The global data is synchronized to each SAS so that it can be used to implement enterprisewide security. The MAS itself does not have any directly connected controllers or video servers, but it can be used to
remotely monitor and manage controllers and video servers attached to SAS's in the enterprise.
MAS/SAS architecture typically follows a 'Hub/Spoke' model where the Master is the hub and the Satellites are the
spokes which can be deployed globally.
In a victor environment, each MAS deployed on a system supports up to 20 SASs. Satellite servers provide real time
response for critical operations like events and actions while the master server provides a rolled up reporting and event
management interface for the customer.
Refer to Appendix A: victor MAS/SAS Support for further details including installation instructions.
5
Updates
Introduction
You can update client and VideoEdge NVR (4.4+) recorders from within the victor unified client. Updates files are
hosted in a repository on the victor Application Server machine and can be downloaded by connected clients and
pushed to supported recorders.
Tyco Update Utility
During install, the Tyco Update Utility is installed alongside victor client. This component communicates with an
update repository which is hosted on the victor Application Server providing a means to update Tyco software.
The update application lists all available updates that can be installed on the user’s system along with the location of
the machine hosting the update repository.
Tyco Update Utility can be launched by navigating to ‘C:\Program Files (x86)\Tyco\UpdateClient’ and launching
TycoUpdateUI.exe. Once launched
Utility.
will display in the system tray. Double click to relaunch the Tyco Update
Note:
In order to download and install updates using the Tyco Update Utility, you must have Windows administrator rights.
victor
victor client checks for available updates:
• Daily if run for more than 24 hours without a restart
• Automatically on client startup
• Automatically when the client connects to a new victor Application Server
• Manually from the ‘About’ page
Note:
Automatic and manual update checks can only be carried out if the current victor user has the 'Administrator' role in
victor.
The ability to check for updates can be added to roles other than ‘Administrator’ by using the Type Exception
Workstation - Update victor client.
Only victor client users who have the Administrator or Power User role are allowed to perform updates to the victor
client. If the current victor user does not have one of these roles then the update options will be disabled.
6
Hosting victor Client Updates
In order for victor unified client to update, the update files must be hosted on the victor Application Server machine in
the update repository.
Procedure 3-1 Hosting victor Client Updates
Step Action
1
Double click update executable to launch. Installer dialog opens.
2
Select Next. End User License Agreement (EULA) dialog displays.
3
Select I accept... or I do not accept... as applicable.
4
Select Next. Ready to Install the Program dialog displays.
5
Select Install. Tyco Update Repository begins to install. Once complete, InstallShield Wizard Complete
dialog displays.
6
Select Finish. A new folder called “Repository” is created in the location ‘C:\Program Files (x86)
\Tyco\Update Server Repository’ which hosts update files for victor unified client.
- End -
Updating victor Client
Automatic Updates
If an update is available, launching victor unified client, the client being open for 24 hours or connecting to a new victor
Application Server will display a dialog stating:
“The victor Application Server you are connected to has an update available. Installing this update will cause
victor client to be closed. Would you like to automatically download and install this update?”
Follow the procedure below to install the update. To skip the update, select Remind Me Later.
Procedure 3-2 Install Automatic Update
Step Action
1
Select Install. The victor unified client license agreement dialog opens
2
Read the license carefully and select Accept or Decline as applicable
3
If Accept is selected, victor client will close and a dialog will display showing progress of downloading and
installing updates. The update can be canceled by selecting Cancel during the download of update files.
Note:
During the upgrade, if the Tyco Update application is running, the user is informed of progress via a
system tray status display.
4
Once update is complete, select OK
- End -
7
Manual Updates
Users with appropriate permissions can manually check for and install updates from within victor unified client.
Procedure 3-3 Install Manual Update
Step Action
1
Select
then About. The about tab opens.
2
Select Check for Updates.
3
If no update is available, dialog will display “Software is up to date”. If there is an update available, dialog will
display:
“The victor Application Server you are connected to has an update available. Installing this update will cause
victor client to be closed. Would you like to automatically download and install this update?”
4
Select Install. The victor unified client license agreement dialog opens.
5
Read the license carefully and select Accept or Decline as applicable.
6
If Accept is selected, victor client will close and a dialog will display showing progress of downloading and
installing updates. The update can be canceled by selecting Cancel during the download of update files.
Note:
1. Progress dialog will not display if User Account Control (UAC) is enabled.
2. During the upgrade, if the Tyco Update application is running, the user is informed of progress via a
system tray status display.
7
Once update is complete, select OK.
- End -
8
VideoEdge NVR
Updates can be applied to VideoEdge NVRs from the client via the recorder’s context menu.
Before performing the update, the NVR checks the current version installed against the version to be installed. If it is
not a higher version, an alert is posted to the client, informing it that the update failed and the reason for failure.
If security is enabled on the NVR, the user is prompted for credentials before the update is applied.
After successful update and restart of NVR services, an alert is sent to the victor client indicating to it that the
installation was a success.
Caution
1. When a software update is applied either via a push update or applied manually using the Administration Interface,
NVR services will restart. Temporary NVR service outage should therefore be expected when an update is applied.
2. It is recommended that you should schedule when NVR upgrades are applied and expect a loss of video when
services restart. When upgrading NVRs which are being monitored by a secondary (Failover) NVR you need to stop
Server Monitoring to prevent the secondary NVR taking over when the upgraded primary NVR's services stop.
Note:
VideoEdge NVR updates can only be carried out if the current user has ‘Edit’ permissions on the applicable VideoEdge
NVR recorder.
Update VideoEdge NVR
VideoEdge NVR software update bundles can be hosted on the site server update repository and pushed down to
individual recorders via the client GUI.
Procedure 3-4 Update VideoEdge NVR
Step Action
1
Right click the recorder to be updated.
2
Select Check for Updates.If updates are available, Do you want to install upgrade dialog displays.
Note:
If no updates are available, dialog displays - No Update available
3
Select Yes. Dialog advises that the recorder will be offline for a period of time.
4
Accept EULA. Recorder goes offline during upgrade.
Note:
During upgrade, any alerts related to success or failure of updating display in victor’s activity list.
- End -
9
Getting Started
Introduction
This section describes the basic steps on involved in how to start victor services (victor Professional only), launch the
client after installation and provides an overview of the main Graphical User Interface (GUI).
It is important to read this section as it provides useful user information on a number of basic/common tasks which are
not repeated throughout the manual and are not related to specific object types or scenarios.
Server Configuration Application (victor Professional)
The Server Configuration Application provides a management interface for administration of various server settings. It
is accessible directly from the desktop via the Server Configuration Application icon or via the Windows Start Menu
(All Programs > Tyco > victor > Server Configuration)
The Application comprises the following tabs:
• Services - Allows Framework and Extension services to be manually started and stopped
• Server Components - Allows manual start/stop of Bidirectional server components
• Database - Displays database connections
• Settings - Allows Enable/Disable of Application and Network settings
Restarting services (victor Professional)
After initial installation, all applicable services will be running. However, victor services may need to be restarted when
new licenses are added to ensure full functionality is available.
Note:
1. Crossfire Framework Services must be started first to allow Extension services to run
2. victor Express does not require services to be started manually
Procedure 4-1 Restarting victor Services
Step Action
1
Double click the Server Configuration Application Icon on the desktop. The Server Configuration
Application displays.
Note:
Depending on security settings, you may need to right click the icon and select Run as
Administrator.
2
Select the Services tab.
3
Select Stop for all Framework Services. Status changes to Stopped.
10
4
Select Stop for Extension services as required.
5
Select Start Service for Crossfire Framework Service in the Framework Services section. Wait until
Status:Running displays in Green.
6
Select Start Service for Crossfire Server Component Framework Service in the Framework Services
section. Wait until Status:Running displays in Green.
Note:
All extension services should start automatically. If you need to manually start them, continue to
Step 7.
7
Select Start checkbox for all required extension services.
8
Select Start Service for all required extension services. The status changes to Running.
9
Confirm that all Services have changed state to Running.
10
Exit the Server Configuration Application.
- End -
Launch the Client
Note:
1. Before starting the client, ensure all victor services are running (victor Professional only)
2. Initial sign-in must be from the windows user account under which the client was installed. (During installation, a
client user is created called Installer Account. Because this is the only user which exists at this time and victor uses
Windows authentication, it is important that this user is logged in to Windows.)
Procedure 4-2 Starting the client
Step Action
1
Double click the victor unified client icon on the desktop. The client sign in dialog displays (Unless this is
the first sign on in which case the client will connect automatically).
2
Select Authentication Method the operator uses from the dropdown - Windows or Basic
3
Enter Username (Windows Username of the installer account if this is the first login)
4
Enter Password (Password of the Installer Account)
Note:
Blank Password are not accepted
5
Select Domain and victor Application Server as required
6
Select OK to Login or Cancel to Exit
- End -
11
Exploring the Default Workspace
The default layout for the client is made up of a ribbon control comprising Home, Build and Setup tabs. The tools and
buttons available on each tab is dependent on the components installed, licenses applied and the role of the logged in
user.
Below the Ribbon, The Device List, Surveillance window and status bar make up the rest of the default layout.
Home Tab - User Controls
The Home tab contains typical user/viewer controls. No configuration or setup options are available
Build Tab - Configuration Tools
The Build tab contains administrative tools to configure non hardware objects e.g. Operators, Roles, Video Actions
and Events
Setup Tab - Configuration Tools
The Setup tab contains administrative tools to configure system hardware e.g. General Purpose Devices, Recorders
and Keyboards
12
Status Bar
The Status bar is a static display of System level Information which includes:
• Number of Active Alerts
• Server Name (victor Application Server)
• Client Messages
• Active Operator
• Active Layout
• Bandwidth Configuration (Configurable from the status bar)
• Name of the Active Virtual Matrix
• Workstation Status (CPU Usage/Memory Free/Disk Space Free)
• Current Date and Time
• Any Error Messages detected by the client will also be displayed. For example ‘Recorder has reached its
maximum number of clients’
Device List
The Device list displays a list of all hardware configured in the system in a single window. It is primarily used to
interact with hardware via object icons' context menus.
The device list forms part of the default layout but can be hidden or viewed as required.
Save and Close Options
Save and Close options are displayed and used in all object editors when creating or editing any object types. It is
important to understand the differences between the various options as proper use can save time and effort when
configuring objects.
13
Switch Language/Culture
You can change the language/culture of the text displayed on the application Graphical User Interface (GUI)
Procedure 4-3 Switch Language/Culture
Step Action
1
Select the victor menu
button on top left of GUI. Dropdown menu displays.
2
Select Languages
3
Select the Dropdown menu in the language dialog.
4
Select the required language.
5
Click Select. Dialog displays informing you the next time you run the program, the User Interface will be in
the selected language.
6
Close the victor program.
7
Launch victor. GUI displays in the new language.
button. Language Selection dialog displays.
- End -
Reposition the Quick Access Toolbar
You can reposition the Quick Access Toolbar below or above the ribbon.
Note:
The ribbon is minimized by default
Procedure 4-4 Reposition the Quick Access Toolbar
Step Action
1
Select
from the top left of the client window.
2
Select Show Below the Ribbon or Minimize the Ribbon as required.
3
Select
to reverse the selection.
- End -
14
Common Tasks
There are certain tasks within the client which are identical for all object types and therefore are not repeated in each
chapter. This section gives an overview of some of the tasks and explains how to perform them.
• Show All (Dynamic Views)
• Delete (Objects)
• Refresh Hardware
• Object Editors
• Object Selector
Show All Objects (Dynamic Views)
Object lists (Dynamic Views) are generally displayed using the Show All option from an object type’s dropdown
menu.
These lists will generally contain at a minimum Names and Descriptions of available objects. Depending on the type
of object being displayed, more information may be available by right clicking the column headers and displaying extra
detail.
Procedure 4-5 Show All Objects (Dynamic Views)
Step Action
1
Select the Object Icon from the Build or Setup Tab.
2
Select Show All from the dropdown menu. A List of all selected object types displays.
- End -
Delete Objects
The procedure to delete objects is identical for all object types.
Procedure 4-6 Delete Objects
Step Action
1
Select the Object Icon from the Build or Setup Tab.
2
Select Show All from the dropdown menu. A List of all selected object types displays.
3
Right Click on the object to be deleted.
4
Select Delete. A warning dialog displays.
5
Select Yes to Delete or No to Cancel.
- End -
15
Refresh Hardware
The procedure to refresh hardware is identical for all object types.
Procedure 4-7 Refresh Hardware
Step Action
1
Select Devices from the Home Tab. Device list displays.
2
To refresh ALL objects of a single type:
3
a
Right Click the Parent object.
b
Select Refresh. All objects of that type refresh.
To refresh individual objects:
a
Select
next to object type to expand the selection.
b
Right click the object to be refreshed.
c
Select Refresh. The object refreshes.
- End -
Object Editors
Object editors are used to make changes to existing system objects. They are generally accessible from the Object’s
context menu.
Procedure 4-8 Edit Objects (General)
Step Action
1
Select the object type from the Build or Setup tab.
1
Select Show all to display object list.
2
Right click the object.
3
Select Edit to enter the object’s editor page.
4
Make changes as required.
5
Select Save..
- End -
16
Object Selector
The Object Selector is used throughout the client to select objects or assign actions. It is mainly used for
Administration E.G when selecting role exceptions or Event Actions.
Procedure 4-9 Select an Object
Step Action
1
Select
. Object Selector displays.
2
Select the object type from the Type column. Object column will be filtered based on type.
3
Select object from the Object column.
4
Select OK.
- End -
Cycle Active Tool Windows and Files
For easy navigation between open victor tabs, you can cycle between active tool windows and files.
Hold CTRL and Press Tab to open a dialog displaying active Windows and files. Cycle the active items by pressing
Tab until the required item has focus in the dialog.
Release CTRL to focus on the required item.
17
Device List
Introduction
The Device list provides a means of displaying and controlling all hardware configured in the system in a single
window. It is primarily used to interact with system hardware via object icon’s context menus.
Display/Navigate Device List
The Device list displays a tree view of all hardware devices configured on the system which are available to the
current user.
18
Procedure 5-1 Display/Navigate Device List
Step Action
1
Select Devices from the Home Tab. The device list displays.
2
The Device List window displays showing all devices configured within the system.
3
Use Object Icons to filter view and Context menus to interact.
- End -
Object Status
An object’s Online/Offline Status is visually represented by a graphical ‘light bulb’ associated with the object icon in
the device list.
Note:
1. For analog cameras, Online and Offline status refers to the physical connection between the camera and recorder.
2. Cameras displaying
the icon to Online.
19
(Offline status) may still be streaming video as the system may take some time to refresh
Recorder/Camera Configuration
Recorders Introduction
Recorders can be added to the system manually or multiple recorders may be added using the Recorder Import
function. Recorders can be added from Local Area Networks (LANs) or from across Wide area Networks (WANs)
victor can also be configured to auto-discover VideoEdge recorders. As and when new VideoEdge recorders are added
to the network, victor automatically detects them and prompts the user to add them to the system.
Supported Recorders
Recorder Type
Supported Version
Intellex
4.0+
Intellex IP
4.0+
VideoEdge NVR
4.2+
VideoEdge Hybrid Appliance
4.21+
American Dynamics HDVR
1.5+
American Dynamics TVR
2.2,2.5,2.6
Caution
Ensure time is synchronized between client machines and network recorders. Recorders which are out of time
synchronization with client machines cause incorrect video retrieval. It is recommended that an NTP server is used to
synchronize machines.
20
Add new Recorder (LAN)
You can add supported LAN recorders to the victor Application Server.
Procedure 6-1 Add new Recorder
Step Action
1
Select Recorders from the Setup Tab.
2
Select New from the dropdown menu. Recorder editor displays.
3
Enter the IP Address/Domain Name of the recorder.
Note:
1. If adding a VideoEdge NVR 4.4+ recorder with failover set up, enter the virtual IP address of the
recorder. It is also recommended that the secondary (failover) NVR 4.4+ recorder is added to victor
separately using its static IP address to ensure that all alerts are received.
2. If using a domain name, then it is recommended that a DNS server is used to allow both the client
and the victor Application Server to resolve the device name. It is not recommended to use local host
files to resolve device names.
4
Enter the Communication Port. This can be left blank of default ports have not been changed.
5
Enter the User Name, if required.
6
Enter the Password, if required.
Note:
1. A Username and Password is required when adding VideoEdge NVR units.
2. If adding Intellex 5 recorders with Remote Access Authorization enabled, a Username and
Password is required.
3. It is recommended that an Administrator account is used when adding Recorders to ensure that
full access is available via the client.
7
[Optional] Enter the Communication Port.(Port used for HTTPS streaming)
8
[Optional] Select the Secure Connection checkbox to enable HTTPS communication (VideoEdge NVR
only).
Note:
1. SSL certificates can be created on VideoEdge 4.5+ recorders. These can then be installed on
victor client and victor Application Server machines when adding HTTPS enabled recorders.
2. If using HTTPS, the communication port should match the secure port defined on the VideoEdge
NVR being added.
9
Select Save.
- End -
21
Add new Recorder (WAN)
You can add supported WAN recorders to the victor Application Server.
Procedure 6-2 Add new Recorder (WAN)
Step Action
1
Select Recorders from the Setup Tab.
2
Select New from the dropdown menu.
3
Enter the IP Address/Domain Name of the recorder.
Note:
1. If adding a VideoEdge NVR 4.4+ recorder with failover set up, enter the virtual IP address of the
recorder. It is also recommended that the secondary (failover) NVR 4.4+ recorder is added to victor
separately using its static IP address to ensure that all alerts are received.
2. If using a domain name, it is recommended that a DNS server is used to allow both the client and
the victor Application Server to resolve the device name. It is NOT recommended to use local host
files to resolve device names. Enter the Communication Port (leave blank if default ports have not
been changed).
4
Enter the User Name, if required.
5
Enter the Password, if required.
Note:
1. A Username and Password is required when adding VideoEdge NVR units.
2. If adding Intellex 5 recorders with Remote Access Authorization enabled, a Username and
Password is required.
3. It is recommended that an Administrator account is used when adding Recorders to ensure that
full access is available via the client.
6
Enter the Streaming Port, if required.
7
Expand the WAN Configuration section.
8
Enter the Enter the IP Address/Domain Name of the recorder.
9
[Optional] Enter the Communication Port.(Port used for HTTPS streaming).
10
Enter the Streaming Port.
11
[Optional] Select the Secure Connection checkbox to enable HTTPS communication (VideoEdge NVR
only).
Note:
1. For secure connections, SSL certificates can be created on VideoEdge 4.5+ recorders. These can
then be installed on victor client and victor Application Server machines when adding HTTPS
enabled recorders.
2. If using HTTPS, the communication port should match the secure port defined on the VideoEdge
NVR being added.
12
Select Save.
- End -
22
Add Multiple Recorders
You can add multiple recorders simultaneously using the Import Recorders function. This feature enables you to
import recorder information (Minimum IP Address/Hostname) using information previously entered into a .txt or .csv
file. See example below:
Note:
1. Lists are not case sensitive.
2. Each Recorder must have a separate row on the list.
Procedure 6-3 Add Multiple Recorders
Step Action
1
Create a .txt or .csv file, listing at a minimum the IP Addresses or Hostnames of each recorder to be imported. Create each new entry on a new line. Additional field information may be entered, separate information
relating to each field with a comma.
2
Save the .txt or .csv file.
3
Select Recorders from the Setup Tab.
4
Select Import Recorders from the dropdown menu. Please select a file to import dialog displays.
5
Navigate to the saved file.
6
Select Open. Reading Recorders file dialog displays informing of progress. When complete, imported
recorders display in device list.
7
Select Close on the Reading Recorders file dialog.
23
- End -
Edit Recorders
You can edit properties of existing recorders.
Procedure 6-4 Edit Recorders
Step Action
1
Select Recorders from the Setup Tab.
2
Select Show All. All recorders are listed.
3
Right Click on the recorder to be edited.
4
Select Edit. The Recorder editor displays.
5
Make edits as required.
Note:
Properties which can be edited vary depending upon recorder type.
6
Select Save.
- End -
Configure VideoEdge NVR
victor client supports full configuration of VideoEdge NVR (4.2+).
Procedure 6-5 Configure VideoEdge NVR
Step Action
1
Select Recorders from the Setup Tab.
2
Select Show All. All available recorders are listed.
3
Right Click the recorder to be configured.
4
Select Configure. The recorder’s configuration page opens.
5
Refer to the recorder's User/Administrator guide for configuration help.
- End -
24
Device Discovery (Recorders)
The Device Discovery tool can be used to discover American Dynamics recorders (and associated cameras) on the
victor network.
Note:
Various network/security settings may affect this feature's functionality and performance. Should you encounter any
problems relating to device discovery on your system, you should attempt to resolve them with your IT department
prior to contacting American Dynamics technical support.
System level device discovery settings are configured in System Values>Discovery Preferences. Here you can set
separate preferences for each supported recorder type.
Discovery mode is initiated by selecting Device Discovery on the Setup tab which displays the Device Discovery
window.
The Device Discovery window comprises two panes; one for discovered recorders (upper) and one for associated
discovered cameras (lower).
Add/Ignore devices
You can add discovered devices to victor by dragging and dropping directly from the device discovery window into
victor's device list. Alternatively you can use 'batch' actions by selecting checkboxes next to discovered devices and
using
25
and
to add or ignore devices.
VideoEdge Recorders
victor provides an auto-discovery service which can be used to detect newly added VideoEdge recorders. Newly
discovered recorders can be added to victor by dragging and dropping from the client's discovered list.
Recorders discovered in the last 24 hours are labeled as New
Cameras
The client displays a list of auto-discovered cameras which have not yet been associated with an NVR. Discovered
cameras can be dragged from the discovered list directly into their respective NVR in the device list.
Note:
Newly discovered Illustra cameras can be assigned IP addresses directly from the discovered list, individually or as a
batch.
Remove Cameras
VideoEdge cameras can be removed from NVRs. Removed cameras are automatically placed back on the discovered
list.
Change Camera IP Address (American Dynamics cameras only)
You can change the IP address of American Dynamics cameras from the camera discovered pane using
access the Camera Address Configuration dialog.
to
Use this dialog to define the IP address range to be assigned to selected cameras and to define Network Configuration
settings.
Note:
The NVR will attempt to set the IP address on as many cameras as possible and will not stop assigning IP addresses
in the event of a failure.In the event of failure, gaps of unassigned IP addresses in the requested start/end IP address
range may occur.
26
Recorders - General
Alarm Persistence
VideoEdge NVR constantly caches alarms from the previous 2 weeks data. This means if an NVR loses connection
to the victor Application Server, alarms are resent upon reconnection in Recovery Mode.
Upon Reconnection, notification is sent to victor that Alarm recovery is in progress and also informs whether it has
been successful.
Users must run a Video Alarm report to access the alarms triggered during the lost connection.
Alarm Persistence can be disabled from the Server Configuration Application.
Procedure 6-6 Disable Alarm Persistence
Step Action
1
Right Click the Server Configuration Application on the desktop
2
Select Run as Administrator. Application opens
3
Select the Settings Tab
4
Select Skip Recovered Events Checkbox in the Application Settings section
Note:
If the status of the Skip Recovered Events is changed while the VideoEdge Driver service is
running, it must be stopped and restarted before changes take effect.
- End -
Change Bandwidth Configuration Settings
Current bandwidth and CPU usage is displayed on the status bar.
You can configure bandwidth settings to reflect the capabilities of your network.
Bandwidth is selected from a list of network types which define a maximum bit-rate value to be received from video
servers.
The client allocates a bandwidth limit to each individual active stream by intelligently distributing the total bandwidth
limit associated with the chosen network type.
The ability to change bandwidth type is based on the role allocated to the active user.
Note:
Bandwidth throttling may degrade video quality.
Procedure 6-7 Change Bandwidth Configuration Settings
Step Action
1
Select the current Bandwidth Configuration from the Status Bar. Bandwidth settings display as a popup
menu.
2
Select the required Bandwidth Setting. Options are:
27
Bandwidth Configuration
Bandwidth Cap
VPN
* See Below
Local Are Network (LAN)
Capped by Network Capability
High Speed Broadband
10 Mbps
Broadband
5 Mbps
Low Speed Broadband
1 Mbps
Fractional T1
512 Kbps
Narrowband
256 Kbps
Modem
128 Kbps
The selected Bandwidth cap is applied and will display on the taskbar.
Note:
1. When Bandwidth throttling is being applied, the
symbol displays on the video stream.
2. When a stream has stopped due to client bandwidth configuration, the
symbol displays.
- End -
Virtual Private Network (VPN)
When using a VPN connection, selecting the VPN option informs the NVR that the client machine is on a WAN. This
selection makes transcoding resources available if configured and/or free.
28
Cameras Introduction
After adding recorders, their associated cameras are automatically available to view and configure. Names and
descriptions of cameras can be edited and alerts can be assigned to cameras from the client. Other camera attributes
can generally be viewed but not edited.
Edit Cameras
Camera Names and Descriptions can be edited, and Alerts and Associations can be assigned.
Procedure 6-8 Edit Cameras
Step Action
1
Select Devices from the Home tab. The Device list displays.
2
Navigate to the camera to be edited.
3
Right click on the camera.
4
Select Edit. Camera Editor displays.
5
Expand the General Section.
a
Edit the name, if required in the Name textbox.
Note:
1. Selecting the Use same name as recorder checkbox changes the name of the camera in the
client to that used in the recorder
2. Deselecting Use same name as recorder checkbox offers the option to use a custom name
which is used in the client only (recorder retains the original name)
b
Enter/Change the description, if required in the Description textbox.
c
Select the Enabled checkbox to enable or deselect to disable. Default is enabled.
6
Expand the Associations section. You can use the Object selector to associate a camera with up to 5
objects.
7
Select Save.
- End -
Reset Camera Names
When a camera name is changed within the client, it can be reset back to the original name assigned at the recorder.
Procedure 6-9 Reset Camera Name
Step Action
1
Select Devices from the Home Tab. The Device List displays.
2
Navigate to the camera to be reset.
3
Right Click the camera.
4
Select Reset Name. Name reverts to original.
29
Note:
All Camera names can be reset from the Setup Tab by selecting Reset All Name(s) under the
Cameras Icon
- End -
30
Surveillance
Introduction
Surveillance allows users to view live video from recording devices. Video can be viewed by dragging cameras from
the device list into surveillance panes or by using Call ups to display video from existing Tours and Salvos.
For playback control / navigation of recorded video Playback Controls.
PTZ Control
When viewing a video stream, Pan, Tilt and Zoom (PTZ) control is available using an on screen display (OSD) control.
There are 2 types of PTZ command that the client will determine to use, depending on camera type:
Real PTZ
This can be used on live video streams to control supported dome cameras.
Virtual PTZ
This type is used with fixed cameras for live and recorded video. Virtual PTZ is achieved by capturing a specific area
of the camera’s view, cropping a smaller area and zooming that to a larger view.
View video from all cameras on a recorder
You can view live video from all cameras connected to a single recorder.
Note:
The maximum number of supported live video feeds is 16 H.264 @ 30 ips
Procedure 7-1 View video from all cameras on a recorder
Step Action
1
Select Devices from the Home tab. The device list displays.
2
Select
next to recorders to expand the selection.
3
Select
next to the recorder’s folder to expand the selection.
4
Right click the recorder.
5
Select View. A new surveillance tab opens displaying all available video streams.
- End -
31
Display video from selected cameras
As well as displaying all available video from a recorder, you can select specific cameras to view in the surveillance
window.
Procedure 7-2 Display video from selected cameras
Step Action
1
Select Surveillance from the Home tab.
2
Selected appropriate Video Pane layout using the layout selector icon
. Default view is 1X1.
Note:
You can configure which video layouts are available from System Values > Video Layout
Preferences
3
Select Devices from the Home tab. The device list window displays.
4
Select
5
Expand recorders as required. Camera icons display.
6
Drag and drop camera(s) from the device list into the surveillance pane(s).
next to recorders to expand the selection.
- End -
32
Change Surveillance Overlay Settings
Video Overlay settings can be enabled or disabled within the video window.
Video overlays can be displayed or hidden as required:
• Display Grid
• Camera, Recorder, Names and Time
• Dome Control
• Region of Interest
• Audio
Note:
Changes to overlay options affects the whole window in which the changes are made. Overlay options cannot be set
for individual panes.
Procedure 7-3 Change Surveillance Overlay Settings
Step Action
1
Select Surveillance from the Home Tab. The surveillance window displays.
2
Right Click in the surveillance window.
3
Select Overlay.
4
Select or Deselect options overlay as required.
Note:
Dome Control overlay must be enabled to allow camera control from within specific panes.
- End -
33
Using Virtual Controls (PTZ)
You can use Virtual controls to crop and magnify the view of fixed cameras (virtual Zoom). Virtual controls also allows
users to move and set Picture in Picture views and to set virtual presets.
Note:
Virtual Control overlay must be enabled to allow camera control from within specific panes.
Procedure 7-4 Using Virtual Controls
Step Action
1
Select Surveillance from the Home Tab.
2
Select the Camera Control symbol
PTZ controls display.
3
Use the controls by selecting the areas of the controls as required. When in use, a picture in picture view is
displayed in the main video pane. Use the Move Picture in Picture icon to reposition the view.
within the video pane of the fixed camera you want to control. Virtual
Note:
Picture in Picture behavior can be configured in System Values > Surveillance Preferences
4
Select Close to close the controls.
- End -
34
Virtual Controls (Presets)
You can set virtual presets on a fixed camera. This allows you to view multiple areas of interest quickly without the
need to manually control the camera’s PTZ.
Note:
The maximum number of presets that can be configured is 255
Procedure 7-5 Virtual Presets (Presets)
Step Action
1
Select the Camera Control symbol
within the video pane.
2
Use Virtual PTZ to display the view to be added as a preset.
3
Select Preset
4
Select next sequential preset number from the dropdown.
5
Select
to add preset.
6
Select
to exit back to PTZ controls.
7
Repeat as required for further presets.
. Preset controls display.
Note:
To view presets, select the preset number and click
Go to Preset.
- End -
35
Dome Camera Controls
Where available, you can use real Pan Tilt and Zoom controls from within the client surveillance windows.
Procedure 7-6 Dome Camera Controls
Step Action
1
Select Surveillance form the Home tab. The surveillance window displays.
2
Select
3
Use the controls by selecting the areas of the controls as required.
within the video pane of the dome camera to be controlled. Dome Controls display.
Note:
Depending upon the type of dome and recorder being used, the available controls may vary. For
example, the sequence function is not available when using Intellex.
- End -
Mouse Control
Depending on the current surveillance mode, the mouse can be used to navigate video streams and Pan, Tilt and
Zoom cameras:
• In playback mode you can instantly toggle between X1 forward and X1 reverse by scrolling up or down
• In Live and Playback modes, you can use the scroll wheel to Zoom by clicking and scrolling the wheel
• In Live and Playback modes, you can use the mouse for Pan and Tilt operation by locating the cursor
centrally and clicking and dragging when the
symbol displays
• In Paused mode, the mouse can be used to step forward and back frame by frame
• In Live and Playback modes, holding down the mouse wheel while scrolling zooms the camera view in
or out (Both in vPTZ or Real Dome control)
36
Clear Video
You can clear video from surveillance windows and panes.
Procedure 7-7 Clear Video
Step Action
1
Right Click on the Surveillance Pane
2
Select Clear. Then select from:
a
Clear Video - To clear video from that pane only
b
Clear All Videos - To Clear video from all panes within the window
c
Clear all Pane Selections - To clear all selected panes
d
Clear Region of Interest
- End -
Change Video Layout
Video Layouts can be changed to accommodate different video pane configurations. The video layouts available from
the surveillance window can be controlled from System Values.
Procedure 7-8 Change Video Layout
Step Action
1
Select Surveillance from the Home tab. Surveillance window displays.
2
Select
. A list of available layouts displays. The Layouts are split into sections:
• Standard
• Widescreen
• Portrait
3
Select Layout as required. Video window switches to the selected configuration.
Note:
When changing layouts, the three most recently used layouts are displayed in a recently used list
next to the pulldown list for convenient retrieval.
- End -
37
Still Image Capture
You can capture all or part of a paused video stream as a still image in .bmp or .jpg format. After capture, various
options are available including Save, Email, Print or Copy to clipboard. You can also launch a third party application for
image editing.
Still Image capture is available from any surveillance mode, the method for capture is identical in all modes.
Procedure 7-9 Still Image Capture
Step Action
1
Right Click the surveillance pane.
2
Select Still Image. A new floating window displays with the following options available:
• Select
to browse to a storage location and Save the still image
• Select
to Email the still image (Requires Email to be configured in System Values)
• Select
to open the image in a third party application (Requires third party application
to be configured in System values)
• Select
to copy the image to clipboard
• Select
to print still image (Requires Windows Printer to be configured)
- End -
Fisheye Cameras
Fisheye cameras use very wide angle lenses to capture hemispherical images - 180° panoramic view (wall mount) or
360° surround view (ceiling/floor/wall mount) without blind spots.
victor allows hemispherical images captured from fisheye cameras to be converted into conventional rectilinear or
panoramic projections for viewing and analysis. This process is known as De-Warping.
De-Warping
The option to De-warp is available via the context menu of supported fisheye camera views. This can be done in
Playback and Live modes as well as from within victor Player. It is also available in Video Search Results player and
Investigator windows.
It is worth noting that sending an image to another display or InstantView etc. will open the Fisheye camera in
whichever view is set by default in Setup -System Values- Video Preferences.
Note:
Exported video can be de-warped within victor player but if exported footage is played back in alternative players,
there is no option to de-warp the video.
De-Warping preferences are available in System Values. Here you can configure the default de-warp mode from the
following:
38
Warped View
Default View from a fisheye camera displaying a
hemispherical image with barrel distortion.
Rectilinear View
De-Warped view of a fisheye stream. This view is
designed to display a section of the fisheye view
with minimal barrel distortion.
Panoramic View
De-Warped view of a fisheye stream. This view is
designed to display the full fisheye view in a single
elongated pane.
VideoEdge NVR 4.4+ also offers the option of selecting a default camera mounting for fisheye cameras.
Procedure 7-10 Warp/De-Warp images
Step Action
1
Right Click a video stream from a fisheye camera.
2
Select De-Warp Options De-warping options display.
3
Select from:
• Warped - Maintains Fisheye view
• Rectilinear
• Panoramic
Note:
It is important to select the appropriate mounting option. Each option uses a different algorithm,
designed to give optimal de-warped views depending on camera orientation.
- End -
Fisheye Camera Controls (Warped)
Fisheye camera views have various click and drag OSD controls you can use to manipulate camera views.
Note:
Virtual presets created on a Fisheye camera will also store the warped or de-warped view which was being viewed at
the time of creation
Warped View Mouse Control
In warped views, pressing Shift displays a target box on screen. This box can be moved by dragging the mouse
around the warped view. Clicking the mouse on a particular area displays a new rectilinear (de-warped) view of that
area.
Rectilinear View Mouse Control
In Rectilinear views, hovering the mouse in the centre of the view displays a
symbol. You can Click and Drag the
symbol in any direction to effectively enable Pan and Tilt control. (PTZ control must be open)
Panoramic View Mouse Control
In Panoramic views, similar to Rectilinear, you can use
to Pan and Tilt the camera view. (Zoom mode only)
39
InstantView
InstantView enables users to view video in instant playback (paused) mode alongside the live view.
You can launch instant playback from any surveillance view from the video context menu or by selecting the
InstantView Icon.
Procedure 7-11 Launch InstantView
Step Action
1
From Live video mode, select a video pane. Selected pane highlights dashed yellow.
2
Select
3
Select from:
. Dropdown menu displays.
• Side By Side - to open the new paused view beside the live view
• Send To - to send the paused view to a separate display
- End -
Audio Devices
General
Audio devices are exposed in victor client only via VideoEdge 4.4+ NVRs where all audio object settings are
configured. Refer to VideoEdge User Manual for more details.
Within victor, audio devices generally mirror the behavior of cameras; they are standard victor hardware objects which
are displayed as child objects of NVRs and can be interacted with via the device list.
Audio device editor
As with cameras, victor’s Audio device editor allows you to add alerts and associations, assign descriptions and
rename devices. Associating devices within victor client pushes the changes back to the NVR only if the new
association is with an object within that NVR.
Search and Retrieve
You can drag audio devices into the Search and Retrieve object selection alongside cameras to return audio and video
streams which are not necessarily associated outside of the wizard.
You can also perform Search and Retrieve on audio devices only, this return audio only streams for the parameters
selected.
40
Audio Associations
General
Audio associations are limited to one per device. each association made in victor client is automatically replicated on
the NVR, likewise each association made on NVR is mirrored within victor (when the audio device and camera are
connected to the same recorder).
If multiple audio associations are attempted, only the first selected will be added, the other selections are ignored.
Clip Export and Retrieval
There are some considerations which should be noted concerning clip export and audio associations:
Clips with default audio
Clip and audio are exported together and playback as separate streams within a single clip
Clips with default audio and audio associations
Clip and default audio are exported as a single clip, the associated audio is exported as a separate clip
41
Playback Controls
Introduction
victor’s video Playback Controls provide all the standard VCR operations as well as Jump forward, and Back by
intervals and Date Selection options..
Note:
1. Audio is disabled when in Playback mode unless the video stream is running at X1 forward. Only one source can be
running at a time. For example, enabling audio on camera 2 will disable it on camera 1.
2. Live and streaming audio is unavailable on Intellex playback, it is only available on downloaded clips.
3. To enable audio when playing back retrieved video, select
on the surveillance pane.
4. During playback, if there are gaps in the recorded video stream, Intellex will skip to the next available video.
VideoEdge NVR will return blank frames at the requested framerate across the gap in recording.
5. Instant Playback and Audio is not supported on HDVR units.
Instant Playback
When in Live mode, you can switch to Instant Playback mode, enabling user control of recorded video streams.
Procedure 8-1 Switch between Live Video and Instant Playback
Step Action
1
From Live video mode, select a video pane. (Select multiple panes by clicking on more than one) The Playback controls become active.
Note:
When a surveillance pane is selected, a border displays around the pane:
Yellow Dashed - Instant Playback is available
Yellow Solid - Video stream is in instant playback mode
Blue Flashing - Instant Playback is not available on the selected stream
2
Select the required function from playback controls. The selected pane(s) enter playback mode.
42
3
Navigate video stream(s) as required.
4
Select Exit Instant Playback to exit to revert to Live Video.
- End -
Mouse Control
Depending on the current surveillance mode, the mouse can be used to navigate video streams and Pan, Tilt and
Zoom cameras:
• In playback mode you can instantly toggle between X1 forward and X1 reverse by scrolling up or down
• In Live and Playback modes, you can use the scroll wheel to Zoom by clicking and scrolling the wheel
• In Live and Playback modes, you can use the mouse for Pan and Tilt operation by locating the cursor
centrally and clicking and dragging when the
symbol displays
• In Paused mode, the mouse can be used to step forward and back frame by frame
Clear all pane selections
When multiple panes are selected, you can quickly deselect them all with one action.
Procedure 8-2 Clear all pane selections
Step Action
1
Right click a selected video pane. Context menu displays.
2
Select Clear all pane selections. Borders are removed indicating they are no longer selected.
- End -
43
Call Up Configuration
Introduction
‘Call up’ is the collective name for Tours, Salvos and Saved Views.
Tours
A tour is a collection of different camera views, displayed in predefined sequences for specified durations.
Salvos
A Salvo is a display of multiple, simultaneous video streams which provides an effective way to monitor multiple areas
of interest.
Saved Views
A Saved View is a standard Salvo which is associated with a specific video layout E.G Guard layout.
Create Tours
You can define criteria for a new tour and add it to the system.
Procedure 9-1
Create Tours
Step Action
1
Select Tours from the Build tab.
2
Select New from the dropdown menu.
3
Enter a Name for the tour in the Name textbox.
4
Enter a description for the tour in the Description textbox.
5
The Enabled checkbox is selected by default, to deactivate the tour, deselect the checkbox.
6
If required change the Default dwell time in the Defaults section. This is the dwell time used for each
camera added.
Note:
Dwell times may be changed for individual cameras within a tour by changing the dwell time in the
Tour section.
7
Select the tab in which the cameras to be added are located.
8
Select the camera to be added.
9
Drag the camera to be added into the right hand pane.
44
10
Repeat steps 8-9 as required.
11
Modify dwell times as required for individual cameras by double clicking the dwell value and changing it.
Note:
Presets and Patterns are only available to add if they are already configured on the Recorder. They
cannot be configured via the client. If available, they can be added by selecting them from the Pattern
or Preset textboxes and selecting from the dropdown list.
12
If required, use
to remove items from the camera list.
13
If required, use
and
14
Select Save.
to change the step position of cameras.
- End -
Edit Tours
You can edit the properties of existing tours.
Procedure 9-2
Edit Tours
Step Action
1
Select Tours from the Build tab.
2
Select Show all from the dropdown menu.
3
Right Click the Tour to be edited.
4
Select Edit. Tour editor displays.
5
Edit Name and Description in the General section.
6
The Enabled checkbox is selected by default, to deactivate the tour, deselect the checkbox.
7
If required change the Default dwell time in the Defaults section. This is the dwell time used for each
camera added.
8
Within the Tour section, use
cameras.
9
Edit existing camera’s attributes by changing Preset, Pattern or dwell settings for each camera.
10
Add more cameras by dragging them from the Sites or Recorders list as required.
11
Select Save..
to remove cameras, and use
- End -
45
and
to change the step position of
Create Salvos/Saved Views
Tours, Cameras and Recorders can all be added to Salvos. Presets and Patterns may be assigned to cameras if they
have already been defined on the recorder.
Procedure 9-3
Create Salvo/Saved View
Step Action
1
Select Salvos from the Build tab.
2
Select New from the dropdown menu.
3
Enter a Name in the Name textbox.
4
Enter a description in the Description textbox.
5
The Enabled checkbox is selected by default, to deactivate the tour, deselect the checkbox.
6
Select a Layout from the Layout dropdown if the Salvo is to be a Saved View.
Note:
1. The selected layout must contain enough video panes to accommodate the number of video
streams you intend to add to the Salvo.
2. Saved view can also be created directly from current surveillance views by selecting Save as
Saved View
.
7
Navigate to the required objects to be added to the salvo.
8
Select and drag Recorders/Cameras/Tours into the right hand pane.
9
If required, use
to remove items from the camera list.
10
If required, use
and
to change the step position of cameras.
Note:
Presets and Patterns are only available to add if they are already configured on the Recorder. They
cannot be configured via the client. If available, they can be added by selecting them from the Pattern
or Preset textboxes and selecting from the dropdown list.
11
Change the default Pane number by selecting the Pane dropdown for each Camera/Tour.
- End -
46
Edit Salvos/Saved Views
You can make various changes to salvos and Saved Views. They can be edited to change attributes including Name,
Description, Dwell Times, Add/Remove objects and Layouts (Saved Views only)
Procedure 9-4
Edit Salvos/Saved Views
Step Action
1
Select Salvos from the Build tab.
2
Select Show All from the dropdown menu.
3
Right click the Salvo/Saved view to be edited.
4
Select Edit. The Salvos editor displays.
5
Edit the Name and Description in the General Section.
Note:
The Enabled checkbox is selected by default, to deactivate the tour, deselect the checkbox.
6
Edit Cameras and Layouts as required in the Salvo section.
7
Select Save.
- End -
Launch Call ups
Tours, Salvos and Saved views can be launched from any surveillance window.
Procedure 9-5
Launch Call ups
Step Action
1
Right click on any surveillance window.
2
Select Salvo/Saved View or Tour as required.
3
Select the required Call up. Call up displays.
- End -
47
Search and Retrieve
Introduction
The Search and Retrieve feature allows users to search a recorder’s stored video or metadata using time or motion
criteria to filter results. Search results can be reviewed, vaulted, saved as clips, stored on the client workstation or
exported to remote storage.
Caution
Ensure time is synchronized between client machines and network recorders. Recorders which are out of time
synchronization with client machines cause incorrect video retrieval.
Supported Search Types
All searches are performed using the Video Search and Retrieval Wizard. The wizard comprises of a maximum of 3
screens, through which the user defines search criteria.
Four main search types are supported:
Basic Search
Basic search covers the following options in the Type of Search dropdown menu:
• Date and Time - Searches specific time ranges using only time related parameters.
• Thumbnail Search - A date and time search which displays results as thumbnail images.
All basic searches allow searching by date and time and enable the user to define the search period (Start and End
Date/Time) and streams to retrieve (Video or Video and Audio).
Thumbnail Search
Thumbnail Searches display results in the form of 16 images representative of the selected time range.
Selecting '+' on a single image opens a new set of thumbnails at an increased granularity with the time range
determined by the timestamp of the thumbnails adjacent to the original '+' selected.
Thumbnail search is supported on VideoEdge NVR 4.4+, Intellex and HDVR recorders only.
48
Motion Detection Search
Motion detection search allows users to search for motion in a specific cameras field of view. This allows the user to
skip directly to areas that may be of interest, rather than having to search through hours of video in order to search for a
particular event.
Note:
1. Motion detection based searches and motion based alarms are handled differently within the client. Motion
detection based searches are independent of motion alarm regions set up on a recorder.
2. Motion detection based searches performed on VideoEdge NVR's do not search actual video footage, but rather
metadata generated by the NVR. Search results are therefore dependent on the sensitivity level settings when the
video was processed. If no motion metadata is generated for a particular time period, no results will be returned when
searching on that time period.
3. Motion detection searches performed on the client from Intellex units search actual video footage so results depend
on sensitivity settings set in the client.
4. Motion detection searches are not available on HDVR or ADTVR units.
Video Intelligence Search
Video Intelligence Search is supported on VideoEdge NVR 4.2+ recorders. This gives users the ability to detect, track
and analyze moving objects using a variety of criteria. The Video Intelligence engine is licensable on a per-channel
basis. Supported Video Intelligence searches are:
• Object Detection
• Direction
• Linger
• Enter
• Exit
• Abandoned/Removed
• Dwell (4.5+)
Text Stream Search
victor text stream search provides a means of searching text from configured NVRs devices (V4.5+).
Two types of text stream searches are supported:
• Date and Time: Used to return all text values within a defined time period.
• Advanced: Used to search for specific text values within defined parameters and filters set on the
VideoEdge NVR and victor.
49
Perform Searches
Perform a Basic Search
You can use the Search and Retrieve Wizard to specify parameters in order to perform a Basic Search. Basic
Searches only consider Time and Date parameters.
Procedure 10-1 Perform a Basic Search
Step Action
1
Select Search and Retrieve from the Home tab.
2
Select Execute Search Wizard. The Search and Retrieval Wizard launches.
3
Select the search type required from the Type of Search drop down menu. Available options are:
• Date and Time
• Thumbnail Search
• Motion Detection
Note:
On VideoEdge NVR 4.2+ recorders, available options will vary if Video Intelligence is enabled on the
camera selected. Refer to Perform a Video Intelligence Search (Analytics).
4
If required, select the Download Audio button to download associated audio stream(s).
5
Drag and drop camera(s) from the Device, Site or Vault list onto the Camera Selector Pane.
Note:
If selecting cameras from the Vault List, Date and Time parameters are automatically populated.
6
Specify Date and Time parameters in the Date and Time Pane.
Note:
Selecting Specific Range also allows selection of Time Filter options. Time Filter options can be
used to specify a sub-set of time to search. For example, only search between 9am and 5pm. Select
the Time Filter checkbox to enable.
7
Select Next. The Confirmation screen displays. Confirm your search criteria are correct. Select Previous
to return to the previous screen to make changes. Select Finish to execute the search.
8
Search and Retrieval Wizard closes and the Date and Time Based Search Results tab opens displaying
search results. Double click on a search result to view associated video.
- End -
50
Perform a Thumbnail Search
You can use the Search and Retrieval Wizard to search video footage and display results in Thumbnail view.
Thumbnail search results are represented graphically as a series of snapshots representing the duration of the search
period.
Note:
Thumbnail Search is available for VideoEdge NVR 4.4+, Intellex and ADHDVR recorders only.
Procedure 10-2 Perform a Thumbnail Search
Step Action
1
Select Search and Retrieve from the Home tab.
2
Select Execute Search Wizard. The Search and Retrieval Wizard launches.
3
Select Thumbnail Search from the Type of Search drop down menu.
4
Drag and drop a camera from the Device, Site or Vault list onto the Camera Selector Pane.
Note:
If selecting a camera from the Vault List, Date and Time parameters are automatically populated.
5
Specify Date and Time parameters in the Date and Time Pane.
Note:
Specific Time Filter options cannot be used with Thumbnail Search.
6
Select Next. The Confirmation screen displays. Confirm your search criteria are correct. Select Previous
to return to the previous screen to make changes. Select Finish to execute the search.
7
Search and Retrieval Wizard closes and Video Thumbnail Search window opens displaying search result
as 16 thumbnails
Selecting a thumbnail image will zoom in the time period to create 16 new thumbnail images using the
thumbnails adjacent to the (+) thumbnail as the time range for the next 16 images. Selecting a thumbnail will
zoom out to the previous 16 thumbnails.
Double clicking a thumbnail will open that section of video in Investigator Mode.
Toolbar buttons, as outlined below, can also be used to manipulate thumbnail search results:
Save image - select a thumbnail then
select this button to save the image
Email image - select a thumbnail
then select this button to email the
image
Open in third party application Select a thumbnail then select this
button to open the image in a third
party application. A third party
application must be configured in
System Values
Copy to Clipboard - Select a
thumbnail then select this button to
copy the image to your clipboard
51
Print - Select a thumbnail then select
this button to print
Investigator mode - select a
thumbnail then select this button to
open associated video in investigator
mode
Clip creation tools - select a
thumbnail to be the start time of a
clip, then select Clip Start Time.
Select a thumbnail to be the end time
of a clip, then select Clip End Time.
Select Clip Export to export or vault
the clip
Open Search and Retrieval Wizard Select to reopen Video Search and
Retrieval Wizard
- End -
Perform a Motion Detection Search
You can use the Search and Retrieval Wizard to search video footage using a motion filter to look for movement in
specific areas within a camera view. Specific areas may also be searched by exception.
Note:
When searching on VideoEdge NVR 4.2+ recorders, motion detection search is only enabled when Motion
Detection is enabled in the camera setup. For cameras with Video Intelligence enabled, refer to Perform a
Video Intelligence Search (Analytics).
Procedure 10-3 Perform a Motion Detection Search
Step Action/
1
Select Search and Retrieve from the Home tab.
2
Select Execute Search Wizard. The Search and Retrieval Wizard launches.
3
Drag and drop a camera from the Device, Site or Vault list onto the Camera Selector Pane.
4
Select Motion Detection from the Type of Search drop down menu.
5
Specify Date and Time parameters in the Date and Time pane.
Note:
Selecting Specific Range also allows selection of Time Filter options. Time Filter options can be
used to specify a sub-set of time to search. For example, only search between 9am and 5pm. Select
the Time Filter checkbox to enable
6
Select Next. The Search Parameters screen displays.
Note:
The video stream reverts to the start time selected for the search. To view live video, select
7
Select the required Draw Style and draw a Region of Interest (ROI):
52
.
• Polygon: Draw a polygon by clicking once on the image and dragging the cursor to form
a line. Complete a line by clicking again. Repeat to form the ROI.
Double click when the shape is complete to finalize the search area. Use Clear to
restart drawing and Erase to correct errors.
• Rectangle: Highlight the ROI by clicking and dragging the cursor over the camera view
to form a rectangle. Use Clear to restart drawing and Erase to correct errors.
• Free Draw: Draw the ROI freehand on the camera view. Use Clear to restart drawing
and Erase to correct errors.
Note:
1. By default the ROI drawn is the Active Region, this can be inverted by selecting Invert
Selection.
2. The full camera view can be selected as the Active Region by selecting Select All.
3. Load Alarm Rule allows you to load a previously configured rule from a VideoEdge NVR 4.2+
recorder. victor uses information from the NVR rule to apply search criteria to the victor client search.
Search parameters are populated from the rule but can be edited if required. Refer to Alarm Rules for
more information on alarm rules.
8
Adjust Parameters as required to suit your search type. Available Parameters are dependent on recorder and
camera type.
9
Select Next. The Confirmation screen displays. Confirm your search criteria are correct. Select Previous
to return to the previous screen to make changes. Select Finish to execute the search.
10
Search and Retrieval Wizard closes and the Advanced Search Results tab opens displaying search
results. Double click on a search result to view associated video.
- End -
53
Perform a Video Intelligence Search (Analytics)
VideoEdge NVR recorders support Search Analytics. This gives users the ability to detect, track and analyze moving
objects using a variety of criteria. Refer to the table below for further information on the various types of Video
Intelligence searches and which versions of VideoEdge NVR support them.
In order to perform Video Intelligence searches,the feature must be enabled on the recorder and in some cases, on the
specific camera required. Refer to the VideoEdge NVR User Manual for further information.
Advanced Search
Type
Description
Search Parameter(s)
Object Detection
Find objects that move
into a region of
interest. This is similar
to a normal motion
detection search
except that it only finds
objects the first time
they enter the region.
If the objects leave the
camera view and
return, the search will
find them again.
Draw a region that
covers the area to be
searched for objects.
Use a higher overlap
setting to find objects
that are mostly within
the region, use a
lower setting to find
objects that just brush
the edge of the region.
Overlap (Sensitivity Level) - A
lower value will return more
results.
Direction
Find objects moving in
a certain direction
through a region of
interest.
Set the general
direction of motion to
search for, and the
maximum amount of
time the object can
take to traverse most
of the region (this
excludes objects
which move too
slowly).
Draw a thin region in
the direction of motion
required. Use a lower
overlap setting to find
objects moving in the
general direction but
not necessarily in the
region.
Linger
Detect objects
lingering in a region of
VideoEdge
Version
Supported
4.2+
Overlap (Sensitivity level) - A
lower value will return more
results.
Traversal Time - Maximum
time an object can take to
traverse the region.
4.2+
Direction of Motion - The
direction, North, South, East
or West which the object is
moving.
Overlap (Sensitivity level) - A
lower value will return more
results
4.2+
54
Advanced Search
Type
Description
interest. An object is
lingering if it remains
in the ROI. Set the
minimum amount of
time an object must
linger before being
included in the results.
Draw a region in the
area where you want
to detect objects
lingering. Use a
higher Overlap setting
to avoid detecting
objects lingering
nearby.
55
Enter
Find objects entering
a camera view
through a doorway or
threshold.
Draw a region
containing the
doorway or threshold
and any area around it
through which objects
can be seen (like
glass). Also include
any area through
which the door (if
there is one) might
move. This search
excludes objects that
can be seen through
the doorway or
threshold but do not
pass through it.
Exit
Find objects exiting a
camera view through
a doorway or
threshold.
Draw a region
containing the
doorway or threshold
and any area around it
through which objects
can be seen (like
glass). Also include
any area through
which the door (if
there is one) might
move. This search
excludes objects that
walk up to the
doorway but do not
pass through it.
Abandoned/Removed
Use this search to find
when a stationary
object was placed,
Search Parameter(s)
VideoEdge
Version
Supported
Linger Time - Minimum
amount of time an object
lingers before being included
in results.
Overlap (Sensitivity level) Use a higher overlap setting
for best results.
Overlap (Sensitivity level) Use a higher setting to avoid
finding nearby changes or
changes which are not
completely within the region
Overlap (Sensitivity level) Use a higher overlap to avoid
finding nearby changes or
4.2+
4.2+
4.2+
Advanced Search
Type
Description
moved or removed.
The amount changed
lets you search for
larger or smaller
changes in the region.
The within setting
specifies over what
time period changes
can occur (0 seconds
= instantaneous
change).
Draw a region that
contains all of the area
that you wish to
search for changes,
and use a higher
overlap setting to
avoid finding nearby
changes or changes
that are not completely
in the region.
Face Detection
Use this search to find
when a face is present
in video.
Draw a region that
contains all of the area
that you wish to
search for faces and
use higher overlap
settings to avoid
finding faces nearby.
Dwell
Detect objects
dwelling in a region of
interest. An object is
dwelling if it is mostly
stationary. Set the
minimum amount of
time an object must
dwell before being
included in the results.
Draw a region in the
area where you want
to detect objects
dwelling. Use a higher
Overlap setting to
avoid detecting
objects dwelling
nearby.
Search Parameter(s)
VideoEdge
Version
Supported
changes that are not
completely in the region
Amount Changed - Adjust to
look for a larger or smaller
change in the region.
Within - Timeframe within
which the change occurs.
Overlap (Sensitivity level) Use a higher overlap to avoid
finding nearby faces or faces
that are not completely in the
region
Overlap (Sensitivity level) - A
lower value will return more
results
Dwell Time - Minimum
amount of time an object
lingers before being included
in results.
4.4+
4.5+
Procedure 10-4 Perform a Video Intelligence Search
Step Action
1
Select Search and Retrieve from the Home tab.
2
Select Execute Search Wizard. The Search and Retrieval Wizard launches.
3
Select required Video Intelligence search type from the Type of Search drop down menu.
56
4
Drag and drop camera(s) from the Device, Site or Vault list onto the Camera Selector Pane.
Note:
If selecting cameras from the Vault List, Date and Time parameters are automatically populated.
5
Specify Date and Time parameters in the Date and Time Pane.
Note:
Selecting Specific Range also allows selection of Time Filter options. Time Filter options can be
used to specify a sub-set of time to search. For example, only search between 9am and 5pm. Select
the Time Filter checkbox to enable.
6
Select Next. The Search Parameters screen displays.
Note:
The video stream reverts to the start time selected for the search. To view live video, select
7
.
Select the required Draw Style and draw a Region of Interest (ROI):
• Polygon: Draw a polygon by clicking once on the image and dragging the cursor to form
a line. Complete a line by clicking again. Repeat to form the ROI.
Double click when the shape is complete to finalize the search area. Use Clear to
restart drawing and Erase to correct errors.
• Rectangle: Highlight the ROI by clicking and dragging the cursor over the camera view
to form a rectangle. Use Clear to restart drawing and Erase to correct errors.
• Free Draw: Draw the ROI freehand on the camera view. Use Clear to restart drawing
and Erase to correct errors.
Note:
1. By default the ROI drawn is the Active Region, this can be inverted by selecting Invert Selection.
2. The full camera view can be selected as the Active Region by selecting Select All.
3. Load Alarm Rule allows you to load a previously configured rule from a VideoEdge NVR 4.2+
recorder (Not available on Face detection and edge analytics searches). victor uses information from
the NVR rule to apply search criteria to the victor client search. Search parameters are populated
from the rule but can be edited if required. Refer to Alarm Rules for more information on alarm rules.
8
Adjust Parameters as required to suit your search type. Available Parameters are dependent on Video
Intelligence search type selected.
9
Select Next. The Confirmation screen displays. Confirm your search criteria are correct. Select Previous
to return to the previous screen to make changes. Select Finish to execute the search.
10
Search and Retrieval Wizard closes and the Advanced Search Results tab opens displaying search
results. Double click on a search result to view associated video.
- End -
57
Perform a Text stream search
Text stream searches allow you to return results from all text streams within a defined time period for up to four
devices. Searches can be fine tuned using custom rules to filter unwanted results.
Text stream searches can be performed using the search and retrieve wizard.
Text stream rules
Text Stream Rules allow you to fine tune a Text Stream search. User defined rules may be used to filter search results
and you can add multiple rules or use no rules for searches.
Rules which have been defined on VideoEdge recorders can be selected via victor's search and retrieve wizard to
enable the rules to be applied in victor searches, alternatively you can define and apply text stream rules in victor client
as part of the victor search process.
Rule Groups are used to define a set of rules such that all would have to be true to trigger an alarm. Rules are either
‘OR’ or ‘AND’. So when you perform a text stream search, you can identify ‘AND’ or ‘OR’. If you selected ‘AND’, this
implies ‘RuleGroup’, such that all rules would need to be satisfied for the search result to return true.
Text stream rules can also be used to configure alarms. For example, if you always wanted to know when cash sales
were over $50 or when there was a void, you could define a rule as such.
Procedure 10-5 Perform a text stream search
Step Action
1
Select Search and Retrieve from the Home tab.
2
Select Execute Search Wizard. The Search and Retrieve Wizard launches.
3
Drag a text stream device from the device list into the device selector pane.
4
Specify Date and Time parameters in the Date and Time Pane.
Note:
Selecting Specific Range also allows selection of Time Filter options. Time Filter options can be
used to specify a sub-set of time to search. For example, only search between 9am and 5pm. Select
the Time Filter checkbox to enable.
5
Select Next. Text stream rules window displays
6
Select rule checkboxes to apply existing VideoEdge rules to the search (if applicable). Use And/Or operators
as required to filter your results.
To define custom rules:
7
a
Select
. Rule edit dialog displays
b
Enter a name for the rule in the Rule Name textbox
c
Enter a value for the text match in the Text Match textbox. This is the primary value associated with the
rule which is used by the search wizard.
d
Enter the Search Direction associated with the rule (Forward or reverse)
e
Enter Jump n Results value (numbers of characters ahead of the search term to include in results)
f
Enter Criteria (operator for the rule)
g
Select Preview (optional) to test the rule and gain a preview of the results
Select Next. The Confirmation screen displays. Confirm your search criteria are correct. Select Previous
to return to the previous screen to make changes. Select Finish to execute the search.
58
8
Search and Retrieval Wizard closes and the Text stream based Search Results tab opens displaying
search results. Double click on a search result to view associated video and text stream.
- End -
59
Analytic Heat Maps
A camera heatmap based on analytics data provides a visual representation of analytic activity over time. A still image
of the camera is overlaid with translucent colored pixels that indicate how much activity each pixel 'saw' in a given
time frame.
Note:
Motion Detection or Video Analytics must be configured for the camera on the VideoEdge recorder for at least the
duration of the time range you are mapping.
Procedure 10-6 Generate Analytic Heat Map
Step Action
1
Right Click the required video stream in surveillance mode.
2
Select Analytic Heat Map.
3
Select the time range in which to search using the date and time pickers.
Note:
The start and end times relate to the total time range searched (not a daily interval)
4
Select Generate Heat map. A still image is displayed, overlaid with translucent colored pixels. A Key is
displayed to the right of the image indicating the colors used. Colors range from Dark Blue (least activity) to
Red (most activity)
Standard surveillance tools are available for the heatmap image including Save As, Email, Open in third party
application and Print.
- End -
60
Alarm Rules
Alarm Rules allow users to load previously configured searches into victor Search and Retrieval Wizard. When
loaded, Alarm Rules will automatically populate the Region of Interest along with additional Search Parameters. This
feature enables users to store commonly used searches in order to speed up repeated searching.
Alarm Rules are only supported on VideoEdge 4.2+ recorders.
Save Search as Alarm Rule
As well as using alarm rules defined within the NVR, you can also create new alarm rules using criteria defined in
specific victor searches. These alarm rules display in the Load from Alert Rules list in the Search and Retrieval
wizard when the camera they have been saved against is selected.
Procedure 10-7 Save Search as Alarm Rule
Step Action
1
Perform a Motion Detection or Video Intelligence search.
2
Select
3
Enter a name for the saved search in the Alert Name textbox.
4
Select OK. The search is saved as an alarm rule and will be available for selection on Motion Detection or
Video Intelligence searches.
. Save Search as Alert dialog displays.
- End -
Load Alarm Rule
Load Alarm Rule allows you to load a previously configured alarm rule from a VideoEdge NVR 4.2+ recorder. victor
uses information from the NVR rule to apply search criteria to the victor client search. Search parameters are
populated from the rule but can be edited if required.
Note:
Load Alarm Rule feature is not available on Face Detection or Edge Analytic searches
Procedure 10-8 Load Alarm Rule
Step Action
1
Select Search and Retrieve from the Home tab.
2
Select Execute Search Wizard. The Search and Retrieval Wizard launches.
3
Select Motion Detection or required Video Intelligence search type from the Type of Search drop down
menu.
4
Drag and drop camera(s) from the Device, Site or Vault list onto the Camera Selector Pane.
Note:
If selecting cameras from the Vault List, Date and Time parameters are automatically populated.
5
61
Specify Date and Time parameters in the Date and Time Pane.
Note:
Selecting Specific Range also allows selection of Time Filter options. Time Filter options can be
used to specify a sub-set of time to search. For example, only search between 9am and 5pm. Select
the Time Filter checkbox to enable.
6
Select Next. The Search Parameters screen displays.
7
Select required Alarm Rule from the Load from Alert Rules list.
8
Search parameters are populated with Alarm Rule parameters. If required, edit search parameters.
9
Select Next. The Confirmation screen displays. Confirm your search criteria are correct. Select Previous
to return to the previous screen to make changes. Select Finish to execute the search.
10
Search and Retrieval Wizard closes and the Advanced Search Results tab opens displaying search
results. Double click on a search result to view associated video.
- End -
Investigator Mode
Launching Investigator Mode opens a new Guard window with the selected, main video stream in paused mode
occupying the upper left pane.
This mode allows you to drag in up to 5 other streams, each will automatically pause at the same time as the selected
stream, enabling a time synchronized view of all cameras.
Note:
Investigator mode can be launched from any surveillance view and is also available from the Search Results window.
Procedure 10-9 Launch Investigator Mode
Step Action
1
Select the main video stream from which to launch Investigator mode. Yellow border displays around pane
indicating instant playback is available.
2
Select
3
Drag in other cameras as required. These video streams are paused at the same point as the main video
stream.
4
Select Playback controls as required to navigate the video streams simultaneously.
. Investigator mode launches in a new window.
- End -
62
Export Search Results
You can export search results as a grid in Microsoft Excel (.xlsx) or .xps formats.
Procedure 10-10 Export Search Results
Step Action
1
Perform a search using the Search and Retrieve Wizard. Results display in the Search Results window.
2
To export the search results:
• In Excel format select
.
• In .xps format select
3
Navigate to the Save in folder as required.
4
Select Save.
- End -
Quick Search and Retrieve
Quick Search and Retrieve can be used to retrieve recent footage from a single camera. Quick Search and Retrieve
can jump backwards 30 seconds, 1, 5, 10, 30 or 60 minutes. To perform a search with more defined time parameters,
refer to Perform a Basic Search.
Procedure 10-11 Quick Search and Retrieve
Step Action
1
Navigate to the camera on the device list and right click.
or
Right click the surveillance pane for that camera.
2
Select Search and Retrieve. Available time intervals display.
3
Select required time interval. Search results window displays.
4
Search result displays when download is complete.
- End -
63
Jump to Next/Previous Alerts or Results
The Jump to Next/Previous results buttons allow for navigating alerts and video search results.
This feature is available for alerts when in instant playback mode, the required alert types are enabled and alerts are
available. It is available for search results whenever there are multiple results available.
Search results and Alert types are selectable via the combo box
.
Search results are only enabled when results of a previous advanced search are available.
If viewing multiple video streams and alarms are triggered on more than one camera, Jump To actions mirror the order
of alarms in the journal.
Procedure 10-12 Jump to Next/Previous Alerts or Results
Step Action
1
If viewing Alerts, Use
to select the Alert type.
2
Select
to Jump to the Next Result/Alert.
3
Select
to Jump to the Previous Result/Alert.
- End -
64
Clips
Introduction
Clips are segments of video and audio that are stored remotely from their original recorder.
Clip Creation/Saving
Clip creation tools can be used to define start and end times for video clips from any surveillance window. After
creation, you can then choose to Export (locally or remotely), Save, Archive or Vault the video clip.
Procedure 11-1 Create/Save clips
Step Action
1
Select the video pane from which to create the clip.
2
Navigate to the start time from which to create the clip.
3
Select
. Clip Start time is set.
4
Select
when the video stream reaches the end time of the clip to be created.
5
Select
. Direct Clip Action dialog displays showing camera options summary. From the Direct Clip
Action dialog, the clip can be vaulted, saved or exported. For more information, refer to Clip Actions
Note:
If required, you can select
beside the camera name to remove it from the clip.
6
Select Save. Saving Location options display.
7
Edit the clip name by double clicking the Clip Name textbox and entering text as required.
8
Select the Audio checkbox to save associated audio.
9
Select Clip Saving Location (Remote or victor unified client).
10
Select a clip folder to save to.
65
Note:
You can use right click to Rename, Refresh, Delete, Export or Add a new folder.
11
Select Save. Dialog displays informing whether the save was successful.
Note:
If the clip was from a VideoEdge NVR or HDVR recorder, you will be prompted to enter a passphrase
for validation purposes. Enter and confirm the passphrase and select OK.
- End -
Clip Actions
Once a clip has been created, it can then be vaulted, saved, exported or archived from the Direct Clip Action dialog.
For more information on creating a clip, refer to Clip Creation/Saving. Additionally, clips that have previously been
created and saved can then be exported.
Vault Clips
Vaulting a clip tags it as protected, preventing it from data culling.
Note:
Vaulting is only supported on VideoEdge NVR 4.2+ recorders.
Procedure 11-2 Vaulting a Clip
Step Action
1
Create a clip using Clip Creation/Saving. Direct Clip Action dialog displays.
2
Select Vault. Progress bar displays showing progress of vaulting.
3
Vaulting Complete message displays.
- End -
66
Exporting saved Clips
Clips can be exported to external media. Clips can be exported in Native (.img, .iso - playable using victorPlayer) as
well as.avi/.mp4 formats. Clips can be exported directly as part of the clip creation process or they can be exported
from the clip list.
Note:
Exporting Clips is only available in Live Mode for HDVR recorders
Procedure 11-3 Exporting saved clips
Step Action
1
Select Clips from the Home tab.
2
Right click the clip to be exported.
3
Select Export Clips. Direct Clip Action dialog displays. From this dialog you can use calendar controls to
edit start and end times by clicking the start/end time values.
4
Select Export. New dialog displays from where you can define Export locations, Passphrases, Export
Options and Notes
5
Select Export Location(s) textbox:
• Select
to add export location(s).
• Select
to select the export location(s).
• Select
to remove export location(s).
6
If prompted, enter and confirm a Passphrase.
7
Select export options.
8
If required, select the Download Audio checkbox.
9
If required, select the Export victorPlayer checkbox. For more information on victorPlayer, refer to
victorPlayer
10
If required, select the Specify Filenames checkbox. This allows you to enter user friendly filenames for the
clips.
11
Select Native or AVI/MP4 as file format.
Note:
1. Watermarking is not supported in Native format clips
2. Selecting AVI/MP4 format offers a slider bar, use this to control clip output quality
3.If the clip is a text stream export, an additional Export Text Stream check box will be available
12
If required, select Watermarking Video checkbox.
Note:
Watermarking clips is a role governed feature which allows you to add user defined graphics or text
to exported media. Refer to Watermarks for information on configuring watermark graphics.
13
If required, select Display overlay (includes video overlay in export)
14
If required, select the Notes tab and add text as required.
67
15
Select Export. If Specify Filenames was previously selected, proceed to Step 14. If Specify Filenames
was not selected, export begins.
16
Enter filename as required in the Filename textbox.
17
Select Export. Progress bar displays showing progress of export.
18
Select Finish.
- End -
Archive Clips
Clips from VideoEdge NVR 4.4+ recorders can be archived for long term storage. For more information on archiving
and how to set it up on your VideoEdge NVR recorder, refer to the VideoEdge NVR 4.4 Installation and User Manual.
Procedure 11-4 Archiving a Clip
Step Action
1
Create a clip using Clip Creation/Saving. Direct Clip Action dialog displays.
2
Select Archive. Progress bar displays showing progress of archiving.
3
Archiving Complete message displays.
- End -
Clip Storage
Saved Clips are displayed and selectable from the Clips window.
Procedure 11-5 Organize Clip Folders
You can create, rename and build folder structures for clip storage. This allows you to meaningfully organize local clip
storage
Step Action
1
Select Clips from the Home tab.
2
Select Show all from the dropdown menu. Clips window displays in device list tab group, displaying all
saved clips.
3
The following right click options are available:
• Refresh Folder
• Rename Folder
• Delete Folder
• Export Folder
• New Folder
4
Use right click options as required to organize folders.
- End -
68
Procedure 11-6 View/Edit Saved Clip Notes
Notes can be stored against clips when they are saved or exported. These notes can be viewed and/or edited from the
Clips window for saved clips.
victorPlayer supports note viewing for exported clips.
Step Action
1
Select Clips from the Home tab.
2
Select Show all from the dropdown menu. Clips window displays in device list tab group, displaying all
saved clips.
3
Select required clip. Notes for selected clip are displayed in the Notes textbox.
4
If required, select Notes textbox and edit notes.
5
Select
to save.
- End -
View and Delete Saved Clips
Saved clips can be viewed and deleted as required.
View Saved Clips
Procedure 11-7 View Saved Clips
Step Action
1
Select Clips from the Home tab
2
Select Show all from the dropdown menu. Clip folders are displayed
3
Right click the clip to be played
4
Select Playback Clips. The clip displays in a new window
5
Select
to enable audio. Use playback controls to navigate clip
- End -
69
Delete Saved Clips
When saved clips are no longer required, they can be deleted.
Procedure 11-8 Delete Saved Clips
Step Action
1
Select Clips from the Home tab.
2
Select Show all from the dropdown menu. Clip folders are displayed.
3
Expand the required clip folder.
4
Right click the folder to be deleted.
5
Select Delete Clips. A Warning dialog displays. Select Yes to delete the clip or No to cancel.
- End -
victorPlayer
victorPlayer is a proprietary media player developed by American Dynamics. It is a portable application and is
required to play .img files from Intellex recorders. victorPlayer can also be used to playback clips in the following
formats:
• .ISO (from VideoEdge NVR recorders)
• .ZIP (from HDVR recorders)
• .IMG (From Intellex Recorders)
victorPlayer can also be included with exported clips.
Playing Clips
The primary purpose of victorPlayer is to facilitate clip playback.
Note:
victorPlayer has various options during clip playback. In addition to the standard surveillance playback controls, you
can also: Toggle Full Screen, Clear Video, Restart Playback, Verify Clips (Standard and using Key files) and
perform Still Image Capture by right clicking the playback window.
Procedure 11-9 Play Saved Clip with victorPlayer
The following steps assume that victorPlayer is available on the local machine. If it is not available, it can be exported
as part of victor’s clip export feature. For more information on exporting clips, refer to Exporting saved Clips.
Step Action
1
Launch victorPlayer, select required language then select OK.
2
Saved clips are displayed in the clip list.
3
Drag and drop the required clip into the surveillance window. The clip will begin playback.
70
Note:
To view more than one clip at one time, select View Surveillance from the View menu to open
additional surveillance panes
- End -
Procedure 11-10 Play External Clips with victorPlayer
In addition to using victorPlayer to play clips from the clip list, victorPlayer can also play external video clips.
Step Action
1
Launch victorPlayer select required language then select OK.
2
Select File.
3
Select Open. Select clip file to open dialog displays.
4
Browse to the clip to be opened.
5
Select Open.
6
Drag and drop the required clip into the surveillance window. Clip will begin playback.
Note:
To view more than one clip at one time, select View Surveillance from the View menu to open an
additional surveillance pane.
- End -
Configuring victorPlayer
victorPlayer’s Overlay and Layout settings can be configured as required.
Overlay settings can be configured by selecting Overlay Settings from the View menu, selecting required elements
then selecting OK.
To save your current layout, select
then choose a location and select Save. To load a previously saved layout
select Load from the Layout menu, locate the saved layout and select Open.
71
Verifying Clips
Exported clips can be checked for authenticity by using the Verify Clip tool. The tool checks whether the clip has
been tampered with. In addition to verifying exported clips in victor client, clips can also be verified in victorPlayer.
Note:
Only exported clips can be verified.
Procedure 11-11 Verify Exported Clip
Step Action
1
Select Clips from the Home tab.
2
Select Verify. Browse dialog displays.
3
Browse for and select the clip to be validated.
4
Select Open.
5
If prompted, enter the passphrase associated with the clip. This is the passphrase entered at the time the clip
was initially created.
6
Select Validate. Clip Validator displays informing whether clip is valid.
Note:
The clip validator also offers the ability to Validate with Key File (NVR Only)
This verification method checks for integrity using a key file generated on the NVR to verify exported and archived
clips which were signed using a private key
- End -
Procedure 11-12 Verify Clips in victorPlayer
Step Action
1
Launch victorPlayer.
2
Drag and drop the clip to be verified into the Surveillance window.
3
Right click on the video pane.
4
Select Verify Clip.
Note:
If the clip has been exported from an HDVR or NVR unit, you will be prompted to enter a Passphrase
5
The Clip Validator dialog displays informing whether clip is valid
Note:
Right clicking the video pane also offers the ability to Verify Clip Using key File (NVR Only)
This verification method checks for integrity using a key file generated on the NVR to verify exported
and archived clips which were signed using a private key
- End -
72
Maps
Introduction
The Maps feature provides a dynamic view of physical security objects within a visual representation of their
environment.
Physical objects are represented by icons to form an integrated, unified view allowing monitoring and reaction to state
changes in real time.
Real-time visualization of event activity can be achieved by linking Map actions to Events.
Supported Image files are:
• *.dwg / *.dxf (Vector)
• *.png / *.jpg (Raster)
Note::
1. victor automatically converts vector graphics to .jpg and stores them in the database.
2. CAD Layers: Only CAD Layers visible at the time of import are visible within the image in victor. However, once
imported, new layers can be added to the converted CAD image and used to configure icons. The actual CAD layers
do not exist in victor.
3. Map Image files can be updated without disassociating the icons which were previously placed on the map.
4. victor supports image files up to 20 MB
Importing Map Images
To store an image file on the database, you need to import and save the image file. These procedures describes the
basic steps to import and save an image file as a Map. The map then needs to be configured.
Procedure 12-1 Import a Map Image
Step Action
1
Select Maps from the Build tab.
2
Select New from the dropdown menu. New Map editor displays.
3
Enter a name for the map in the Name textbox.
4
Enter a description for the map in the Description textbox.
5
The Enabled checkbox is selected by default, deselect to disable the map.
6
Select
. Select Drawing File dialog displays.
7
Select
. Browse window displays.
8
Browse to and select the required image file.
9
Select Open.
10
Select Import. File imports and displays in map editor.
73
11
Select Save..
- End -
Procedure 12-2 Export CAD File
A CAD file (.dwg or .dxf) can be exported from victor as a .jpg file. This enables CAD files to be exported, edited as
required then imported for use as a map.
Step Action
1
Select Maps from the Build tab.
2
Select New from the dropdown menu. New Map editor displays.
3
Enter a name for the map in the Name textbox.
4
Enter a description for the map in the Description textbox.
5
The Enabled checkbox is selected by default, deselect to disable the map.
6
Select
. Select Drawing File dialog displays.
7
Select
. Browse window displays.
8
Browse to and select the required CAD file.
9
Select Open
10
Select Export to File. Save As dialog opens
11
Navigate to the location you want to export to and enter a File Name
12
Select Save.
- End -
Procedure 12-3 Remove Blank Space from CAD Drawing
While importing a CAD file (.dwg or .dxf), victor can remove any vertical blank space surrounding your image.
Step Action
1
Select Maps from the Build tab.
2
Select New from the dropdown menu. New Map editor displays.
3
Enter a name for the map in the Name textbox.
4
Enter a description for the map in the Description textbox.
5
The Enabled checkbox is selected by default, deselect to disable the map.
6
Select
. Select Drawing File dialog displays.
7
Select
. Browse window displays.
8
Browse to and select the required CAD file.
9
Select Open
10
Hover over the imported CAD drawing, reduce the size of the window (horizontally) then click refresh.
11
Click Refresh
12
Select Import. File imports, preserving removed blank space and displays in map editor.
74
13
Select Save.
- End -
Configure Maps
Once an image has been imported to create a map, the map can then be configured for use by adding map layers and
icons.
Layers
victor Maps make use of layers - enabling users to manage various object types on different 'levels' within one map.
Procedure 12-4 Add and Configure Map Layer
Step Action
1
From the Map editor select
. Map Layers editor displays.
Note:
The Map editor can be accessed by selecting Maps from the Build tab, then selecting Show All.
Right click on the map to be edited and select Edit.
2
Select Add. A new layer will be added to the Map Layers
3
To rename the new layer, select the Layer textbox and edit as required.
4
Use the Show in map checkbox to select if the layer is displayed on the map.
- End -
75
Add/Configure Map Icons
Icons are added to maps to represent victor objects. Various icon properties can be configured depending on the object
type they represent.
Procedure 12-5 Add and Configure Icons
Step Action:
1
Drag and drop victor objects from Device List into the Map editor. An icon will be added to the map, linked to
the victor object.
Note:
Objects can also be dragged onto maps from Site, Call ups and Object lists
2
3
To configure an icon's characteristics:
a
Right click the icon
b
Select Edit
c
Assign characteristics in the Icon Editor
d
Select OK
Select Save.
Note:
In addition to using this procedure, icons can be added and configured by selecting
instructions.
and following on-screen
- End -
Clone Icons
You can use an existing icon as a template from which to configure a new icon.
Procedure 12-6 Clone Icon Configuration
Step Action
1
From the map editor, select the icon you want to clone from.
2
Drag and drop a victor object from Device List. The icon (with original icons configuration) will be added to the
map.
3
Right click the new icon and edit as required.
- End -
76
Configuring areas
Procedure 12-7 Configure an Area
victor Maps allows for the configuration of areas in order to group icons. Should any icons related to an area go into
Alert status, the entire area will highlight (this applies to icons where annunciation is set to Strobe, Pulse, Blink, Fade
or Flash).
Step Action
1
From the Map editor, hold the Shift key and draw the required area using your mouse.
Note:
The Map editor can be accessed by selecting Maps from the Build tab, then selecting Show All.
Right click on the map to be edited and select Edit
2
The area can be manipulated by using the grab handles.
3
The drawn area can be further manipulated by right clicking and selecting from:
• Select all related icons
• Clear all related icons
• Hide this shape drawing
• Remove this shape drawing
• Send to back
• Bring to front
• Display automatically when in view mode
- End -
You can also configure areas on maps which relate to regions assigned on other maps. This can be useful as you can
then click on a map region to view a more detailed map relating to an area you are particularly interested in.
E.G., You may have a map representing a full campus view and several related maps representing buildings within the
campus.
When you see an alarm annunciating when monitoring the full campus map, this feature allows you to navigate directly
to the more detailed building maps for an enhanced view of the alarm area.
Procedure 12-8 Configure areas related to other maps
Step Action
1
Open target map. This is typically the overview of the whole area you are monitoring, in this case the
'campus' map.
2
Select
3
Select the Map icon. Icon displays on map. Reposition/resize icon as required.
4
Right click the icon.
5
Select Drop on Map. Icon editor displays.
6
Select Select Object.
7
Select the required map. (This is typically the detailed map - in this case the 'building' map)
. Icon selector displays.
77
8
Select OK. Icon editor displays.
9
Assign icon attributes as required.
10
Select OK.
11
Right click the map icon.
12
Select Polygon Shape.
13
Select Add. Triangle displays.
14
The area can be manipulated by using the grab handles. Move and resize the triangle as required to represent
the area covered by the detailed (building) map. Various right click options are available for the shape
including:
• Hide this shape drawing
• Remove this shape drawing
• Send to back
• Bring to front
• Display automatically when in view mode
15
Select Save.
- End -
78
Viewing Maps
Once a map has been created and saved, it can be viewed directly from the Home tab.
Procedure 12-9 View Maps
Step Action
1
Select Maps from the Home Tab.
2
Select the map you wish to view from the dropdown menu. Map opens.
3
The map can be manipulated using toolbar buttons, as detailed below:
Element
Details
Zoom controls - displays current zoom level
percentage along with Fit to Window and
Zoom Out/In buttons
Hide Icon Types - opens the Hide Type
editor which allows selection of icon types
to hide, e.g. Cameras or Recorders
Show All Icons from All Layers - shows
and highlights all icons from all visible
layers.
Note: icons that are on layers that have
been hidden using the Map Layers editor
will not be displayed
Show All Shapes from All Layers - shows
all configured areas from all visible layers.
Right-click to display FoV or Shapes only.
Note: areas that are on layers that have
been hidden using the Map Layers editor
will not be displayed
Activity List - opens a map specific Activity
List that displays the 100 most recent
activities relating to objects on the map.
Icon will display with a red border when
there are unread items in the Activity List.
Right click and select Clear to clear the
activity list. Select the padlock icon to freeze
the Activity List for 30 seconds
Layers - opens Map Layers editor allowing
selection of map layers to show/hide
Hover Mode - select to enable hover mode.
When enabled, hovering over objects will
display additional information. For example,
hovering over a camera will open a pop-up
surveillance pane within the map view,
displaying live video from the camera. Other
cameras can be dragged and dropped into
the pop-up windows
79
Health Mode - select to enable health
mode. When enabled, icons will be
highlighted with their health status. When
enabled with hover mode, hovering over
icons will display the objects health
dashboard within the map view
Note:
1. When viewing a map, the toolbar will display green. If the toolbar displays orange, this means that
the map has been edited and saved since it was opened. Select
to update.
2. When viewing a map, drag any icon onto any surveillance pane to view its associated video.
Monitors on Maps
Monitors can be added as icons to maps either from the device list or from the icon editor within the map.
Monitor icons are sensitive to dragging and dropping of all objects with a 'view' mode (e.g., cameras)- any object
supporting a 'view' mode can be dropped onto a monitor icon and the associated views will be displayed on the
physically associated monitor.
80
Editing Maps
Once a map has been created and saved, its properties can be edited.
Procedure 12-10 Edit Maps (General)
Step Action
1
Select Maps from the Build tab.
2
Select Show All.
3
Right Click the map to be edited.
4
Select Edit. Map editor opens.
5
Change Name, Description, Enabled status in General section as required.
6
Select Save..
- End -
Procedure 12-11 Edit Maps (Map)
Step Action
1
Select Maps from the Build tab.
2
Select Show All.
3
Right Click the map to be edited.
4
Select Edit. Map editor opens. The map can be manipulated using the toolbar buttons, as detailed below:
Element
Details
Import a map - re import the map
image
Increase/Decrease height of map
window
Fill image in window - fit map to
window
Fill on load - when the map loads, fit
map to window
Add Object Icon - add an object icon
to the map
Copy Icon to Active Layer - copy an
icon to the current active map layer
81
Show all icons from all layers displays all icons from all layers of the
map
Show all shapes from all layers displays all shapes from all layers of the
map. Right-click to display FoV or
Shapes only
Active layer - the current active map
layer
Add Text - Displays a field enabling
free text input. Font size/color/type can
be changed as required. Text boxes can
be copied to other areas of the map.
Layers - Show/Hide or Add/Remove
layers
Hover - Enable/Disable hover in the
map editor
5
Edit map elements as required
6
Select Save.
- End -
Procedure 12-12 Edit Maps (Map Icons)
Once an icon has been added to a map, its properties can be edited or copied to create a new map icon. Available
options vary depending on map icon type.
Step Action
1
Select Maps from the Build tab.
2
Select Show All.
3
Right Click the map to be edited.
4
Select Edit. Map editor opens.
5
Right click on the icon you wish to edit.
6
Select required option from the right click menu.
7
Make changes as required.
Note:
Selecting Copy from the right click menu will copy both the icon and all its properties (e.g. assigned
object and assigned left click action)
8
Select Save.
- End -
82
Field of View
A Field of View (FoV) can be attached to a camera icon on a map. FoV gives an indication of the area covered by a
camera.
Procedure 12-13 Attach Field of View to Camera Icon
Step Action
1
Select Maps from the Build tab.
2
Select Show All.
3
Right Click the map to be edited.
4
Select Edit. Map editor opens.
5
Right click on the camera icon you wish to attach a FoV to.
6
Select Field of View (FoV).
7
Select Add. The FoV editor opens.
8
Edit FoV Angle value by selecting
field.
9
Edit FoV Rotation value by selecting
Rotation field.
10
Edit FoV Scale value by selecting
to increase or
to increase or
to increase or
to decrease. You can also free type in the Angle
to decrease. You can also free type in the
to decrease. You can also free type in the Scale field.
Note:
Right clicking the Field of view in edit mode presents varios options which can be toggled on/off as
required
1. Show FOV control Window
2. Anunciate with active alert
3. Hode/remove field of view drawing
4. Send to back/bring to front
5. Move shape when icon is moved
6. Display automatically in view mode
11
Select OK to apply.
12
The FoV can be further manipulated by right clicking and selecting from:
• Show FoV Control Window
• Annunciate with active alert (FoV will only annunciate if icon is set to Strobe, Pulse,
Blink, Fade or Flash)
• Hide this FoV drawing
• Remove this FoV drawing
• Send to back
• Bring to front
• Move shape when icon is moved
• Display automatically when in view mode
13
Select Save.
83
- End -
Copy Maps
An existing map can be copied to create a new map. The new map will be named ‘Original Map Name_Copy’. All map
properties and object icons will also be copied.
Procedure 12-14 Copy a Map
Step Action
1
Select Maps from the Build tab.
2
Select Show All.
3
Right Click the map to be copied.
4
Select Save As. A confirmation dialog opens.
5
Select Yes.
6
A new map will be created in the object list.
- End -
84
Object Association
Introduction
The concept of Object Association refers to linking together otherwise unrelated objects with the intent of enhancing
incident building capability.
The feature enables a ‘Review’ option on the context menu of associated objects. Selecting Review opens a guard
surveillance view displaying the source object and up to 5 associated objects.
After associations are made, the Review feature is exposed in 3 areas of the client; Reports, Event Viewer and
Activity List.
Note:
1. Objects can reference other objects of the same type but cannot reference themselves.
2. Certain supported objects E.G., doors, which do not display video, will not display the Guard surveillance view. In
these cases, a Map view will open displaying the object's location (if configured on Maps).
3. If a source object has no associations, selecting Review will return a view of the type.
4. If the source object is a non-video object and has no associations, the review feature will not be available for any
related events or alerts.
5. For the feature to function properly, it is recommended all associated objects are synchronized to a common NTP
server.
Typical Use Cases
1
Motion Alarm has been triggered and the associated Event Acknowledged. The user still needs to view video
associated with the Alarm.
Without Object Association, reporting capabilities only show you the time of the alarm. The user must open a
surveillance window, drag in the camera that caused the alarm and navigate back to the time of the alarm
using the report data.
With Object Association, the user simply selects the Review option from the report item to perform all the
above functionality automatically.
2
Building on Use Case 1, if there are more cameras associated with the alarm.
Without Object Association the user must find them and drag each camera individually into a surveillance
window and navigate to the time of the alarm.
With Object Association, the Review feature launches investigator mode and displays all associated camera
views.
3
Similar to 1 and 2 but related to Non Video devices E.G., Doors. If a door is forced and an event activated,
the feature can be used to view video from associated cameras in the door’s vicinity.
85
Review Feature
The Review option is exposed in 3 areas of the client:
• Reports: When associations are configured, the source can be accessed from report items by selecting
Review in the item’s context menu.
• Event Viewer: When associations are configured, behavior is similar to that of Reports but the source is
the cause of the event. The source can be accessed by selecting Review in the context menu of the
Event Viewer item.
• Activity List: When associations are configured, the source of the activity list items can be accessed
by selecting Review from the context menu of Activity list items.
Create Object Associations
You can associate a maximum of 5 objects with any of the classes listed:
Video Cameras
DSC Partition/Zone
Doors
MZX Panel/Point
Inputs/Outputs
Simplex 4100 Panel/Point
Readers
Salvos
This procedure describes how to associate a video camera with other video cameras.
Procedure 13-1 Create Object Associations
Step Action
1
Select Devices from the Home tab. Device list displays.
2
Select
next to Recorders to expand the selection.
3
Select
next to the specific recorder.
4
Right click the camera to be edited.
5
Select Edit. Camera editor displays.
6
Expand the Associations section.
7
Select
8
Select the object to associate using the object selector.
9
Select OK.
10
Select Save.
. Object selector displays.
- End -
86
Dynamic Views
Introduction
Dynamic Views are generally displayed using the Show All option from an object type’s dropdown menu.
These lists will generally contain at a minimum Names and Descriptions of available objects. Depending on the type
of object being displayed, more information may be available by right clicking the column headers and displaying extra
detail.
Sort/Filter Objects within Dynamic Views
You can sort objects within Dynamic Views by selecting field names.
Procedure 14-1 Sort/Filter Objects within Dynamic Views
Step Action
1
Select the required object type from the Setup or Build tab.
2
Select Show All. Dynamic View displays.
3
To Sort objects:
• Select a Column Header to sort by. Objects sort alphabetically.
4
To Filter Objects:
a
Select the filter icon
from the required column header for which the data is to be filtered.
b
Select the filter criteria from the dropdown menu. Dynamic View updates to reflect the selected filter.
- End -
Custom Filters
You can apply custom filters to Dynamic Views to help find specific information or limit the scope of a list.
Procedure 14-2 Apply Custom Filters
Step Action
1
Display the Dynamic View.
2
Select the filter icon
displays
3
Select Custom. Custom Filter Selection window displays.
4
Select Add Condition.
5
Select the operator from the Operator dropdown menu.
6
Select the operand from the Operand dropdown menu.
from the required column header for which the data is to be filtered. Dropdown menu
87
7
Select OK. The Dynamic View updates to reflect the filter criteria.
- End -
Object List - Group by Field
You can group Dynamic Views by field names using the Group By Area.
Procedure 14-3 Object List - Group by Field
Step Action
1
Display the Dynamic View.
2
Select the Group By Area. This is the solid bar under the Dynamic View Controls. Group By Area displays.
3
Drag column headers into the area. The Dynamic View updates to reflect the grouping.
4
Use the controls in the Group By Area to manipulate the view.
- End -
Export Lists
You can export Dynamic Views in .XPS and Excel format.
Procedure 14-4 Export Object Lists
Step Action
1
Display the Dynamic View. Sort and Filter as required.
2
To export as a .xps document:
3
a
Select
Export the Grid. Save As dialog displays.
b
Navigate to the Save in folder.
c
Change name of file as required in the File name textbox.
d
Select Save. .xps file saves in selected location.
To export as an Excel document:
a
Select
Export the Grid to Excel. If Excel is installed, it automatically loads the file. If Excel is not
installed, a Windows dialog displays - select from the options displayed.
- End -
88
Create/Save Dynamic Views
After configuring a Dynamic View to display as required, you can save the view for later retrieval.
Procedure 14-5 Create/Save Dynamic Views
Step Action
1
Configure the Dynamic View as required.
2
Select Save the current grid configuration. Create/Save dialog displays.
3
Enter a name for the view in the Name textbox (Mandatory).
4
Enter a description for the view in the Description textbox (Optional).
5
Select the Default checkbox if you require this view to be the default for displaying the dynamic views of this
object type.
Note:
To display a dynamic view which is not set as default, select Dynamic View on the Build tab and
select Show All. Right click on the view and select Show the view.
- End -
89
Operators
Introduction
Operators are users of the client. Each operator is assigned a role which describes their capabilities and privileges.
Operators are authenticated in one of two ways:
• Windows Authentication - requires an assigned Windows principal (domain/workstation name and
username) which relates to a Windows OS account.
• Basic Authentication -The victor Application Server manages users accounts without the need for an
assigned Windows principal or Windows OS account.
Create a New Operator
New operators can be added to the system.
Procedure 15-1 Create a New Operator (Windows Authentication)
When using Windows to authenticate operator accounts, Windows credentials are checked when the operator logs in
to the client. As such, operators will only be able to log in if they have been assigned a user account on both the client
and victor Application Server machines. If a domain controller is not being used, these accounts must be created
manually and be logged into to activate them.
Note:
Windows Authentication is not available when using victor Express.
It is recommended that the role level assigned to the operator account, mirrors somewhat the role level assigned to the
Windows user account.
Caution
Operators created in victor standalone systems with 'non administrator' roles may lack the privileges required to make
similar changes in unified systems.
Step Action
1
Select Operator from the Build tab.
2
Select New from the dropdown menu.
3
Enter a name for the Operator in the Name textbox.
4
Enter a description in the Description textbox.
5
The Enabled checkbox is selected by default, to deactivate the operator profile, deselect the checkbox.
6
Select Windows Authentication.
7
Enter Domain/victor Application Server.
8
Enter Username.
90
Note:
Username should correspond to a Windows username and should not be the same as the name of
the PC.
9
Select a Role from the Roles section.
Note:
Only one role may be assigned to each operator.
10
Select Save.
- End -
Procedure 15-2 Create a New Operator (Basic Authentication)
When using basic authentication to authenticate operator accounts, victor Application Server manages user accounts
without the need for corresponding Windows user accounts.
Step Action
1
Select Operator from the Build tab.
2
Select New from the dropdown menu.
3
Enter a name for the Operator in the Name textbox.
4
Enter a description in the Description textbox.
5
The Enabled checkbox is selected by default, to deactivate the operator profile, deselect the checkbox.
6
Select Basic Authentication.
7
Enter Username.
8
Enter Password.
9
Select a Role from the Roles section.
Note:
Only one role may be assigned to each operator.
10
Select Save.
- End -
Remotely Log Operator Out of Workstation
Operators can be remotely logged out of particular workstations on the network.
Procedure 15-3 Remotely Log Operator Out of Workstation
Step Action
1
Select Devices from the Home tab.
2
Select
3
Right click the workstation you wish to log the operator out of.
91
next to Workstations to expand the selection.
4
Select Log Operator [operator username] Out. Warning dialog opens, prompting confirmation of the
logout.
5
Select Yes to log the operator out, or No to cancel.
- End -
Change Single Sign-on Value
The log-in window will display at client start up only when the Single Sign-on option is set to ‘False’; with Single Signon set to ‘True’, the Login window is bypassed and the server will rely on the current windows identity credentials from
the Windows OS to establish a client connection.
This procedure describes how to change single sign-on values between ‘true’ and ‘false’.
Note:
Depending on your UAC settings on Windows 7 the following procedure may vary slightly, you may be notified or
asked for permission to continue before making changes to the file.
Procedure 15-4 Change Single Sign-on Value
Step Action
1
Navigate to ACVS.Enterprise.Client.Core.Host.exe.config file on the client machine. The default location
for this file is C:\Program Files\Tyco\victorClient.
2
Right click the ACVS.Enterprise.Client.Core.Host.exe.config file.
3
Select Open. Message displays informing Windows cannot open this file.
4
Select Select a program from a list of installed programs.
5
Select OK. Open with...dialog box displays.
6
Select WordPad from the program list.
7
Select OK. File opens as a text document.
8
Change single signon value to ‘True’ or ‘False’ as applicable
9
Select Save.
10
Close Windows.
- End -
92
93
Events
Introduction
General
An event can be considered as anything significant that happens within your victor system.
Creating and implementing system events allows you to detect, monitor and record specific activity on the system.
A typical use may be to use a map action to alert a user of motion detection on a camera covering a sensitive area.
In this scenario, an event could be configured to:
• Alert the user by visually triggering a Video Action associated with the event displaying video from other
cameras in the area
• Trigger a map action showing the location of the of the camera in alarm state
• Create a high priority entry in the Journal requiring operator acknowledgment
Configuration within victor
Typically an event's triggers and responses rely on the creation of object dependencies within the system which are
configured using two editors:
• Event/Action Pairing Editor
• Events Setup
Event Processing
From a system perspective, event processing can be considered in three stages:
• Event Source: Emit events into the processing system (e.g., a motion detection alert sent from a camera)
• Event Processing: Capture, routing and any further processing of emitted events – victor can be configured
to process events in various ways e.g., according to priority, date/time or source.
• Event Result: The system reaction to the event. In the case of victor this could be a video action configured
to display a salvo
94
Conceptual workflow/victor workflow
95
Event Types
Within the victor environment, there are two main event types: Sensor based and Health based.
Sensor Based Events
These events, when triggered typically display predefined Event Actions. These are system actions, tied to events
which are set to display when events are triggered. Examples of Event Actions can be video Salvos or Map actions.
The following general steps are involved in configuring a Sensor based event:
1
Add a trigger to the sensor device (e.g., Set motion detection on a camera)
2
Create the Event Action to be executed when the Event triggers
3
Create the Event
4
Associate the Event Action with the Event
5
Associate the Event with the Trigger
Health Based Events
System Health events do not typically involve video actions as their primary use is not security based. Instead they
are used to warn users of potential issues with system failure. A typical use may be to inform a user that an alarm has
been received warning of CPU overheating.
Acknowledge and Clear Options
Acknowledge and Clear options can be configured for individual events. Configuring these settings determines
whether an event requires extra user information to be entered in order to acknowledge or clear the event.
Options are:
• Require a Log Message to be entered when acknowledged
• Require a Log Message to be entered when Cleared
• Username and password required to acknowledge
• Username an password required to clear
Note:
These credentials can be from any user who has permission to acknowledge and clear the event.
Event Templates
A number of Event Templates are predefined within victor, these can be used as a basis for configuring events of the
type they relate to.
96
Log Messages
Log messages are typically used to clear and acknowledge events but can be entered manually written to the journal
at any time.
Log messages can also be selected from a Predefined Message Log which can contain up to 3000 user defined
messages.
Event Priority Window
The Event Priority Window is a surveillance window which is used to view camera Call Up Actions associated with
Events. The surrounding red border distinguishes the Event Priority Window from standard surveillance views.
It is a 2X2 configuration. Call up video is displayed according to the priority of the event it is associated with. Highest
priority displays in the top left pane of the window, descending in priority to Top right, Bottom left and Bottom right.
New events having a higher priority than those already displayed on will ‘Bump’ the lower priority windows. This will
lead to lowest priorities dropping off when more than four streams attempt to display.
Video streams cannot be viewed in the Event Priority window unless triggered by an event.
The window must be open when the event triggers in order to view the camera call up; the event does not cause the
window to open.
Create Event Actions (Video)
Event actions are the actions triggered by victor in response to specific events. These can be video actions: Preset,
Salvos, Call ups, External Camera Alarms or Map actions.
Procedure 16-1 Create Event Actions (Video)
Step Action
1
Select Video Actions from the Build tab.
2
Select Video Action type from the dropdown menu.
3
Select New. Video Action editor opens.
4
Enter a Nameand Description for the video action as required.
5
Select objects as required from the left pane and drag to the right.
Note:
If creating a Salvo video action, choose from Select from Existing or Create New Salvo.
6
Select Save. Event Video action is created.
- End -
97
Create Event Actions (Maps)
Event actions are the actions triggered by victor in response to specific events. These can be video actions: Preset,
Salvos, Call ups, External Camera Alarms or Map actions.
Map actions can be configured to display when an event triggers to show a map of the event location and highlight the
alarming object.
Procedure 16-2 Create Event Actions (Maps)
Step Action
1
Select Display Actions from the Build tab.
2
Select New from the dropdown menu. Display Map Action editor opens.
3
Enter a Name and Description for the Map action as required.
4
Select a Map.
a
Select
to select from existing maps. Object Selector Displays.
Select
to create a new map. Refer to Maps Chapter for further information.
or
b
5
Select the required map from the object column.
6
Select OK to confirm the selection or Cancel to Exit.
7
Select
8
Select the monitor to display the Map Action.
9
Select Save.
to select Monitor. Object Selector displays.
- End -
98
Create Events
Events can be created and configured from within the client.
Procedure 16-3 Create Events
Step Action
1
Select Events from the Build tab.
2
Select New from the dropdown menu. Event editor displays.
3
Enter a name for the event in the Name textbox.
4
Enter a description for the event in the Description textbox.
5
The Enabled checkbox is checked by default, uncheck to disable the event.
6
Expand the Properties section.
7
Select the priority of the event from the Priority Dropdown menu.
Note:
Each priority level is associated with a color which is made prominent in the Event viewer when the
event is triggered.
8
Select Event Breakthrough if required. The default setting is disabled, enabling Event Breakthrough assigns
priority to the event viewer when the event is triggered so over rides anything else the user is viewing.
9
Expand the Text Section.
10
a
Enter Activate Text in the text box. This text will display in the event viewer, If you have the activity list
open, this text displays as the event triggers.
b
Enter Instructions for the user in the Instructions text box. These will be conveyed to the user when the
event triggers.
Expand the Sounds section.
a
Select the Play Sound When Active checkbox if an audible alarm is required when the event triggers.
b
Select
c
Select Open. The sound is associated with the event and will play when the event triggers.
d
Select OK.
. The Select Sound dialog displays. Navigate to and select the required .wav file.
Note:
1. Only .wav sound files are supported.
2. The files must be located in the ...\\WINDOWS\Media folder. If a custom .wav file is required,
copy it to this location.
11
Expand the Acknowledge and Clear Options section. Select or deselect checkboxes depending on how
you require the event to be acknowledged and cleared.
12
Select Save.
- End -
99
Events - Save As
Existing Events can be used as templates to create new events. This is useful if you need to create an event which is
similar to but not identical to an existing one. The copy of the original event keeps all properties.
Procedure 16-4 Events - Save as
Step Action
1
Select Events from the Home tab
2
Select Show All
3
Right click the event to be copied
4
Select Save As. The new Event is saved with the original name appended with ‘-Copy’. The event can be
edited as required.
- End -
100
Event Viewer - (General Information)
The Event Viewer is a dynamic display of system event activity, accessible from the Home tab. It is a real time list
displaying active and acknowledged events.
From the event viewer you can:
• Acknowledge system events
• Clear system events
• Sort events according to priority
• View event details including instructions, causes and activation time
• Review associated video
• Group events by type
Note:
1. When there are 2000+ events in either the Active or Acknowledged panes, paging buttons are displayed
2. When paging buttons are in use, Acknowledge All and Clear All buttons work on a per page basis
3. By default, 2000 events per page are displayed, this can be changed to 500 or 100 by selecting the Page Size
dropdown
101
Event Viewer - Sorting and Grouping
Using the grouping area of the event viewer, you can ‘Multi Level Group’ on any of the columns displayed. This means
you can sort groups by more than one priority.
Procedure 16-5 Event Viewer - Sorting and Grouping
Step Action
1
Select Event Viewer on the Home tab. Event Viewer displays.
2
Select the Group By area. Area expands enabling column headers to be dragged into it.
The Group By area is the solid divider under the object list controls.
3
Click and drag a column header into the Group By area. Groupings update accordingly.
4
Multi Group the items by adding more column headers.
Note:
By default, events are sorted by Name.
- End -
102
Event Viewer - Acknowledge/Clear Events
From the Event Viewer, depending upon role permissions, you can acknowledge and clear events individually or by
group.
Depending upon Event settings, you may be required to enter username and password or log a message to
acknowledge and clear events.
Actions relating to various buttons on the Event viewer are detailed below.
Button
103
Event Viewer Area
Action
Top Level List (Active Pane)
Acknowledge all events
Top Level List (Active Pane)
Acknowledge and clear all events
Top Level List (Active Pane)
Freeze/Unfreeze pane
Top Level List (Acknowledge Pane)
Clear all events
Top Level List (Active and Acknowledged
Panes)
Print
Event Group (Active Pane)
Acknowledge all activations in event group
Event Group (Active Pane)
Acknowledge and Clear all activations in
event group
Event Group (Acknowledged Pane)
Clear all activations in event group
Event (Active Pane)
Acknowledge individual event
Event (Active Pane)
Acknowledge and clear individual event
Event (Acknowledged Pane)
Clear individual event
Manually Activate Events
An Event can be activated manually rather than be activated by a trigger.
Procedure 16-6 Manually Activate Events
Step Action
1
Select Events from the Build tab.
2
Select Show all from the dropdown menu. All events display.
3
Right Click on the event to be activated.
4
Select Activate. The event will activate and trigger any associated actions.
- End -
Predefined Message Log
Predefined Log Messages can be created which can then be used when required to acknowledge or clear an event
without needing to type text.
Messages are identifiable by their labels which are assigned when they are created.
Labels and message fields are mandatory for every message created. Labels can be up to 100 characters in length
and messages up to 3000.
The language for each message can also be assigned, this means when a user logs a message, the messages
available are filtered to provide current language messages only. To log a message in a different language, you must
switch language in the client.
Procedure 16-7 Create a Predefined Log Message
Step Action
1
Select Predefined Message Log from the Build tab.
2
Select New from the dropdown menu. New Predefined Message editor displays.
3
Select the Language dropdown.
4
Select the language in which the message is to be displayed.
5
Double click the Label textbox.
6
Enter Label text as required. Double click the Message textbox.
7
Enter message text as required.
8
Select
9
Select Save.
to add additional messages or
to remove selected messages.
- End -
104
Events: Batch Configuration
Using the Event/Action pairing editor and the Event Setup editor, you can build multiple event configurations quicker
and easier than building single event configurations one at a time.
Event/Action Pairing Editor
The Event/Action pairing editor is used to tie together system events with actions you wish to trigger.
Note:
Event/Action association can only be made in this editor.
Procedure 16-8 Events/Action Pairing
Step Action
1
Select Event/Schedule Setup from the Build tab.
2
Select Event/Action Pairing from the dropdown. Editor opens.
3
Click the Events node and use the Object Selector to select events as required.
4
Select
5
Repeat as required. Use
6
Select Save.
in the Event node and use the Object Selector to assign event Actions.
and
to add and remove objects.
- End -
105
Events Setup
The Events/Schedule setup editor provides a dynamic, visual method of batch linking Devices, Alerts and Actions as
well as to set up event scheduling.
Procedure 16-9 Events/Schedule Setup Editor
Step Action
1
Select Event/Schedule Setup from the Build tab.
2
Select Events/Schedule Setup from the dropdown. Events Setup editor displays.
3
Double click the Devices node and use the object selector to select the device (Or drag and drop from the
device list).
4
Select
5
Select Add Alerts. Selected alerts are displayed under the Alerts node.
6
Select
7
Repeat as required. Use
8
Use merge and clone options as required to copy configurations:
in node of the device added and use the checkboxes in the dropdown to assign alerts as required.
in the Alerts node and use the Object Selector to assign Actions.
and
to add and remove objects.
Merge and clone target configuration
106
.Duplicate source configuration to all targets
Remove configuration on source and target
9
Use
to add/remove schedules as required. refer to Scheduling for more information on using and
configuring event schedules.
10
Select Save.
Note:
You can configure all system objects of a single type by using the 'Search for Event
Configurations' and filtering by the required type.
- End -
Cloning existing configurations
Cloning provides a quick and easy way of assigning the Event Setup configuration properties of existing configured
devices to new devices.
Note:
As well as cloning event configurations, the duplicate and merge options offer the ability to clone Alerts and Actions
only or Alerts and Actions with Schedules.
In Event Setup, assign existing configurations to new devices by double clicking the device to be cloned and
selecting from:
Merge and clone target configuration
.Duplicate source configuration to all targets
Remove configuration on source and target
• Clone (Merge) - Applies the source's device configuration to newly selected devices, keeping any
existing event configurations
• Clone (Duplicate) - Replicates the configuration of the source device and applies it to the new device,
deleting any existing event configurations.
• Clone (Remove) - Deletes the source device's event configuration
Use the Clone Schedules checkbox to include schedules in the cloning operation.
107
Scheduling
Scheduling is used to manage the execution of events or journal triggers which are to be activated only during
specified time ranges.
Note:
1. Schedules should be assigned meaningful names to allow for easy identification when assigning them to events.
2. Schedules are set on a weekly basis by default i.e., a schedule set from 1200 to 1300 on a Tuesday, recurs every
Tuesday.
The schedule editor's calendar control allows you to select and build schedules by Day, Week (Sunday to-Saturday),
Work Week (Monday to Friday) and Month.
Creating Schedules
Procedure 16-10 Create a Schedule
Step Action
1
Select Schedules from the Setup tab.
2
Select New from the dropdown menu. Scheduling editor displays.
3
Enter a name and description for the schedule.
4
Select the required view (choose the view most suitable for the schedule being created, e.g., if you are
creating a Monday-Friday schedule, select Work Week.
5
Build the schedule by clicking and dragging across the required ranges, selecting hours/days as required.
Click
after each selection to add to the schedule. You can change selected ranges using the grab handles
to increase or decrease as required. Use
6
to remove selected intervals.
Select Save.
- End -
Applying Schedules
victor supports assigning schedules to actions through the Event/Schedule Setup editor. Refer to Events Setup for
further information on event configuration.
Step Action
1
Select Event/Schedule Setup from the Build tab.
2
Select Event/Schedule Setup. Event Setup editor displays.
3
Drag in required device(s) to display event configurations.
4
Select
5
Select the required schedules and time zones to apply to the event configuration (Use Add, Remove
schedules as required).
6
Select Save.
on the Action node. A popup displays all available schedules.
108
Note:
1. By default an action will trigger at all times. Each Action object will have an 'always on' schedule attached to it.
When an action is edited to add a new schedule, the 'always' schedule link attached to the object is removed and the
specific schedule is linked.
2. You can assign schedules to all objects in a view by selecting the schedule icon on the column header node.
3. You can also drag schedules into the event setup editor. This allows you to configure when event configurations are
Active or Inactive.
- End -
Edit Schedules
The Schedules Show All page allows you to view all existing schedules. From within this page you can edit any given
schedule's daily occurrences or you can enter each schedule's own editor to change details such as start/end times,
intervals and ranges.
Procedure 16-11 Edit Schedules
Step Action
1
Select Schedules from the Setup tab.
2
Select Show All. All available schedules display with intervals detailed.
3
To change daily occurrences of schedules:
4
a
Select '+' next to the schedule
b
Check/uncheck the weekdays as required to change the daily occurrences of the schedule intervals
To edit schedules:
a
Right click on the schedule
b
Select Edit. Schedule editor displays
c
Change Name and Description in the General section
d
Make changes to schedule timings in the calendar section e.g.:
• Click and Drag time intervals to move them to different times/days
• Change the schedule scope by selecting Day/Week/Workweek/Month
• Use grab handles on schedules to increase or decrease ranges as required
• Delete time intervals by selecting and pressing Delete (Option is to delete the single
occurrence or the whole series)
• Make schedule ranges 'all day' intervals by selecting and dragging to the top of the calendar
- End -
Active/Inactive Schedules
Whenever a schedule is active i.e., current time is inside its assigned time interval, associated events will be
triggered, outside of the schedule's time interval, events will not trigger.
Alerts will continue whether or not the schedule is active.
109
The Schedules Show All page allows you to view all schedules by status: Active or Inactive. The page updates
dynamically as the schedules displayed start and end their assigned time intervals.
110
External Applications
Introduction
The Add External Applications feature allows users to add shortcuts to the Home tab so external executable files can
be launched from within victor client.
A maximum of six external applications can be added.
Add External Applications
You can add a new button to the Home tab which launches any external application already installed on the client.
Note:
External applications are not retained unless saved as part of a layout. If they are not saved as part of a layout, they
will not be available if the client is restarted or another layout is selected.
Procedure 17-1 Add External Applications
Step Action
1
Select Add on the Setup tab. Selector displays.
2
Navigate to the .exe file of the application to be added.
3
Select the .exe file.
4
Select Open. The applications icon displays on the Home tab and the program will launch when the icon is
selected (Role dependent)
- End -
Edit Application Name
You can change the default name of an external application.
Procedure 17-2 Edit Application Name
Step Action
1
Right click on the application icon on the Home tab.
2
Select Edit Properties. Name textbox displays.
3
Edit the name of the application.
4
Select OK.
- End -
111
Remove External Applications
You can remove external application icons from the Home tab.
Procedure 17-3 Remove External Applications
Step Action
1
Right Click the Icon on the Home tab.
2
Select Remove. Icon disappears from the Home tab.
- End -
112
System Values
Introduction
System Values allows you to configure of a range of system wide settings from a single editor. System Values is
available from the Setup tab.
Bandwidth Configuration
victor Client may be deployed in a limited-bandwidth WAN, or on workstations with limited rendering resources. It is
therefore desirable to minimize the CPU usage on the client PC.
Bandwidth limits can be assigned to operator and role objects. You can change bandwidth limits for operators and
roles by double clicking the Bandwidth Limit text boxes and selecting required values from the dropdown.
You can also choose to preserve either Framerate or Resolution by selecting the appropriate radio button.
If you choose to prefer frame rate, then the stream of the highest rate in the offered palette that most closely matches
the desired resolution will be selected. If you choose to prefer resolution, then the stream that most closely matches
the resolution displayed is selected and allow lower frame-rate streams are picked from the palette.
Bandwidth Configuration can be accessed via System Values.
Clip Preferences
Edit Default Clip Duration
Open System Values from the Setup tab, then select Clip Preferences. Set Default Clip Duration from the
dropdown menu. Available options are: 30 seconds, 1 minute, 5 minutes, 10 minutes, 30 minutes and 60 minutes.
Edit Clip Saving Locations (Local & Remote Directories)
Open System Values from the Setup tab, then select Clip Preferences. Default Local Directory can be set.
Default Remote Directory can be set against each role.
Note:
Default remote directory can be entered as a mapped drive path, it will be automatically converted into UNC
(Universal Naming Convention) format.
113
Watermarks
Watermarking allows custom images to be overlaid on clips exported from victor.
Select System Values from the Setup tab, then select Clip Preferences.
Use
and
to load or delete watermark images. Supported image file types: .bmp, .jpg, .gif, .png
Use the Transparency slider to set watermark transparency (0=Transparent, 100=Opaque)
Select the Enable Watermarking checkbox to enable watermarking (system wide value)
Select the Enable Native Support checkbox to allow users to export clips in native format.
Note:
1. Clips exported in native format will not have watermark applied. Watermarks can only be applied to AVI/MP4 clips
2. Watermarks images should be created on a transparent background
Custom Icons
Using the custom icons feature, you can assign non-default images as object icons. The icons can be assigned at
both Type and Object level enabling specific objects to have a different icon to the object type.
Supported file types: JPG and PNG.
Maximum supported file size: 2MB
Procedure 18-1 Assign Custom Icons
Step Action
1
Select System Values from the Setup tab. System Values editor displays
2
Select Custom Icons. Type and object selectors display.
3
To assign custom icons at type level:
4
114
a
Select the type from the Type dropdown. Default icons display. Multiple icons may display for each
object type as the icons reflect object state.
b
Select Change for the relevant icon. Open dialog displays.
c
Navigate to and select New icon graphic.
d
Select Open. New icon displays next to the object type.
e
Select Save.
To assign custom icons at object level:
a
Select
. Object Selector displays.
b
Navigate to the object.
c
Select OK. New icon displays next to the object type.
d
Select Save.
Note:
Once Custom Icons have been applied, all client areas displaying object states (device list, site list,
maps, etc.) should be refreshed to show updated icons.
- End -
Database Settings
Various database archive settings can be configured using System Values database settings editor.
Open System Values from the Setup tab. Configure Archive, Events and Swipe and Show database settings as
required.
Note:
1. Archive threshold size can only be edited when using SQL Server Express
2. UNC (Universal Naming Convention) should be used when entering Archive directory backup path, e.g.
\\servername\folder)
Discovery Preferences
Use this editor to configure victor Autodiscovery settings.
Device Discovery values are used to configure general system device discovery behavior:
• Discovery Enabled - Select to enable/disable discovery mode
• Startup Delay - Time interval the client waits after startup before entering discover mode
• Poll Frequency - Time interval defining how often victor polls for discoverable devices
For each device type you can configure:
• Discovery Enabled - Select Enable to have victor display discovered devices of that type. Select
Disable to prevent victor discovering devices of that type
• Dynamic Discovery Ranges -Used for every device type except VideoEdge, if this is unchecked you
should provide an IP and Port range in which to search
• IP Address Range - Address range in which victor will search for that device type
• Port Range - Port range in which victor will search for that device type
• Edge Device Discovery Enabled - Check to enable discovery of Edge cameras
• Multicast Address - Used for passive listening (VideoEdge only)
• Multicast Port - Used for passive listening (VideoEdge only)
115
Double Password Protection
Double password protection adds an additional level of security across selected victor global functions, or selected
individual objects. When attempting to access functions or objects that have double password protection enabled, the
user will be prompted for the Username and Password of a second operator.
Open System Values from the Setup tab, then select Double Password Protection. Check required features to
globally protect or select objects using the Object Selector to protect individual objects.
Note:
In the case of conflict, object protection will override global function protection.
Email Preferences
Email settings can be configured in order to use the send still images feature.
Open System Values from the Setup tab, then select Email Preferences. Enter required information and save.
Note:
1. SMTP - Simple Mail Transfer Protocol
2. FQDN - Fully Qualified Domain Name
Journal Filter
The Journal Filter is used to regulate the amount of data being persisted to the victor Application Server database by
blocking/unblocking specific alert types.
Video Camera, Recorder Unit and Storage alerts can be blocked/unblocked, everything else will always be written to
the database.
Procedure 18-2 Using the Journal Filter
Step Action
1
Select System Values from the Setup Toolbar.
2
Select Journal Filter. The Journal Filter editor displays.
To Add Type Exceptions:
a
Select
in the Type Exceptions section. The Type selector dialog displays.
b
Select the Device Type to be filtered.
c
Select OK.
d
Select the Type Exception. The row highlights blue.
e
Select the Alert Category.
f
Block or Unblock Alerts as required.
To Add Object Exceptions:
a
116
Select
in the Object Exceptions section. The Object selector dialog displays.
b
Select the Object type as required. The type’s objects display to the right.
c
Select the Object(s). Use Select All/Clear All as required for multiple selections.
d
Select OK.
e
Select the Object Exception. The row highlights blue.
f
Select the Alert Category.
g
Block or Unblock Alerts as required.
Note:
1. You can use
to Remove Type/Object exceptions as required.
2. To edit exceptions, select the exception and block/unblock alert types as required.
3
Select Save.
- End -
POS Settings
When POS is installed, POS Settings are available and allow for configuration of default search settings and database
management.
Open System Values from the Setup tab, then select POS Settings. Here, database settings can be configured,
along with the amount of time (in seconds) to be added as padding to search results.
Search Preferences
Search preferences can be configured to customize which lists (Site/Device/Vault) open with the Search and Retrieve
Wizard, and which list opens on top.
Open System Values from the Setup tab, then select Search Preferences. Select checkboxes under Open with
Wizard to choose which lists open with the Search and Retrieve Wizard. Select which list to open on top using the
buttons under Top Most.
Video Layout Preferences
Video Layout Preferences allow configuration of which layouts are available for selection.
Open System Values from the Setup tab, then select Video Layout Preferences. By default, all layouts are
selected. Layouts that are selected are available for selection from the surveillance pane, virtual matrix and salvo
editors.
117
Video Preferences
Open System Values from the Setup tab, then select Video Preferences.
Surveillance Preferences
Various surveillance preferences can be configured here, including displaying times in UTC and hiding of virtual PTZ
controls when in Picture in Picture mode.
Fisheye Lens Default Settings
Default behavior when using Fisheye lens should be set here. Use the dropdown menus to select default de-warped
mode - ‘Rectilinear’ or ‘Panoramic’.
Third Party Application
Set which third party application should be used to edit still images. Select
(.exe) for the preferred image editor.
then navigate to the executable file
Video Overlay Preferences
Set font size and color for video overlay in relation to Camera/Recorder and Date/Time information.
Frame Expiry Preferences
This setting uses values from 1 to 20 seconds. In limited bandwidth environments, setting the value allows you to tell
victor how long the system should wait for the next 'good' frame before displying a blank frame.
Select the Never Expire checkbox to ensure no blank frames are ever displayed
VideoEdge Port Setup
LAN streaming can require a large number of User Datagram Protocol (UDP) ports to be open. Configuring port ranges
in System Values (Port Setup) enables traffic to pass through networks with restricted port configuration.
Note:
Restricting ports can also help to make your system more secure.
Default values are:
victor Client UDP port range:Start 6000 End 7999
VideoEdge server UDP port range:Start 32200 End 38199
118
victor Application Server
Introduction
The victor Application Server incorporates an industry-standard relational database used to manage and maintain a
single record of:
• Authorized users/passwords
• Associated recorders and cameras
• Roles and permissions
• Alarm and event journals
• Client license status
Only one instance of victor Application Server is required per site regardless of the number of recorders, clients or
cameras connected.It can be installed on the same PC as the client for smaller sites or on a separate server for larger
sites.
The victor Application Server stores data relating to operator profiles, role information, objects, object status and
who,and what interacts with your video network.
Providing a single point of access for users to manage multiple recording devices, it utilizes SQL Server’s database
functionality to provide authentication for client users, as well as central monitoring and administration of multiple
recording platforms over a Wide Area Network (WAN).
The default victor Application Server record is located at the <client> section of the ‘config’ file but up to twenty server
records are supported. victor Application Servers can be added, deleted and edited using the victor Application
Servers editor on the Build tab of victor client.
Add a new victor Application Server
You can Add, Edit and Delete victor Application Server records using the server editor.
Note:
Each victor Application Server installation supports up to 20 records.
Add a new victor Application Server
Procedure 19-1 Add a new victor Application Server
Step Action
1
Select victor Application Servers from the Build tab.
2
Select Edit from the dropdown menu. victor Application Servers editor displays.
3
Select
. New blank record is created in victor Application Server list.
119
4
Double click the Display Name text box.
5
Enter a Name for the victor Application Server.
6
Double click the IP Address/Domain Name text box.
7
Enter IP Address/Domain Name as required.
8
Double click the Port textbox.
9
Enter the Port number as required (Port numbers 1026-65535 are supported).
10
Select the Default radio button if the new victor Application Server is to become the default.
Note:
The default victor Application Server refers to the server that the client automatically connects to
when single sign on is turned ON. This is the server which will display first on the victor Application
server list on the login dialog.
11
Select Save.
- End -
Edit victor Application Server
You can Add, Edit and Delete victor Application Server records using the server editor.
Procedure 19-2 Edit victor Application Servers
Step Action
1
Select victor Application Servers from the Build tab.
2
Select Edit from the dropdown menu. Server editor displays.
3
Double click in relevant textboxes to edit values.
4
Select Save.
- End -
120
Switch victor Application Server
Procedure 19-3 Switch victor Application Server
You can switch the victor Application Server which victor client is connected to.
Step Action
1
Select
from the client title bar. Operator log out dialog opens.
2
Select Log out. The client sign in dialog opens.
3
Select or enter the Domain from the Domain pull-down menu.
4
Enter Username in the username text box.
5
Enter Password in the password text box.
6
Select the victor Application Server to switch to from the dropdown.
7
Select OK.
- End -
Change Default victor Application Server
Procedure 19-4 Change default victor Application Server
You can change the default victor Application Server victor client connects to.
Step Action
1
Select victor Application Servers from the Build tab.
2
Select Edit from the dropdown menu. A list of all servers displays.
3
Select the Default radio button of the victor Application Server you wish to make default.
4
Select Save.
Refer to Save and Close options for more information.
5
Close and restart victor client. You will now connect to your selected default victor Application Server.
- End -
121
Delete victor Application Server
You can delete victor Application Server records from the system
Note:
The default victor Application Server cannot be deleted.
Procedure 19-5 Delete victor Application Servers
Step Action
1
Select victor Application Servers from the build tab.
2
Select Show Allfrom the dropdown menu.
3
Right click on the server to be deleted.
4
Select Delete. Are you sure you want to delete the specified object warning displays.
5
Select Yes to delete or No to cancel.
- End -
122
Database Backup/Restore
The database backup/restore feature provides a means to collect,save and restore system data. You can backup an
existing Tyco database or restore a database from a specified folder location for the system SQL instance.
The Backup/Restore tab is split into 2 sections - the upper section is used for Database Backup procedures, the lower
section for Restore procedures as shown below:
Procedure 19-6 Backup/Restore databases
Step Action
1
Open the Server Configuration Application.
2
Select Backup/Restore tab.
To Backup a database:
a
Select the required database(s) using the checkboxes next to each database (double click required). Or
select All Databases using the topmost checkbox.
b
Choose the Destination Folder to host the backup (you can select the default SQL folder or specify an
alternate folder).
c
Select Backup database(s). (Backup progress is indicated during the operation). If operation is
successful a dialog displays stating Backup(s) complete.
d
Select OK.
To Restore a database:
123
a
Open the Server Configuration Application.
b
Stop the Crossfire framework Services in the Services tab.
c
Select Backup/Restore tab.
d
Choose the Source Folder which hosts the required backup (you can select the Default SQL folder or
specify an Alternate folder).
Note:
If an alternate location is used, you need to specify the location and click Refresh Backup List to
display available backups in that location.
e
If required, use the Display Options control to view and filter available databases.
f
Select Refresh Backup List to display available backups.
g
Select the required database(s) using the checkboxes next to each database (double click required). Or
select All Databases using the topmost checkbox.
h
Select Restore Selected Databases. Confirmation dialog displays.
Note:
1. If Framework services have not been stopped (step b) an error dialog will display instructing you to
stop the services and try again
2. A warning dialog displays informing of potential data loss due to the restore.
i
Select OK (Backup progress is indicated during the operation). If operation is successful a dialog displays stating Restore(s) complete.
Caution
The Restore Backup procedure overwrites ALL current victor system data.
- End -
124
Vault
Introduction
The vault feature provides the ability to protect media items (audio and video) from VideoEdge NVR (v4.2+) recorders.
Vaulting an item applies a rule to a specific segment of media, tagging it as protected and preventing it from data
culling.
Media can typically be vaulted from:
• Direct Export (Clips)
• Event Viewer - via Export Clip
• Activity List - via Right Click Investigate
• Search Result List - via Clip Export
• Map Viewer - via Export Clip
Note:
Vault option is disabled when non supported recorders are selected and when both non supported and supported
recorders are selected, a warning message is displayed.
Vault List
All vaulted items are listed in the vault list.
From the vault list you can:
• Drag items into the Search and Retrieve wizard and use the vault criteria as a basis for a search. This
selects the camera and date and time
Note:
1. If a subsequent vaulted item belonging to the same camera is dragged into the search and retrieve
wizard, it replaces the original selection and changes the search time frame accordingly.
2. If the vault item belongs to a different camera, a Yes/No dialog displays offering the option to
override the timeframe and have both cameras selected.
3. You can also drag cameras and/or dates from the vault list into the wizard. This means one
camera can contain multiple vaults. In these instances the time range is changed to have a start time
of the earliest vault time and an end time of the latest.
• Drag items into a surveillance pane in which the items are treated as cameras
• Double click items to launch investigator mode, paused at the item’s start time
Hovering on each level of item in the Vault list displays a summary of what is contained in the level below.
125
Procedure 20-1 Display the Vault List
Step Action
1
Select Clips from the Home tab.
2
Select Vault List from the dropdown menu.
- End -
Vault Explorer
The Vault Explorer provides a means to filter vaulted items by Recorder, camera and time range.
It lists all recorders containing vaulted items, branching for each camera with vaulted data.
Procedure 20-2 Locate items using the Vault Explorer
Step Action
1
Select Clips from the Home tab.
2
Select Vault Explorer from the dropdown menu. Vault Explorer displays.
3
Recorder Filter Section - Select the checkbox for each of the recorders to filter by. Cameras that are
associated with the selection and have vaulted media display in the Camera Filter section.
4
Camera Filter Section - Select the checkbox(es) for each camera to filter by.
5
Select:
a
Date/Time Filter - Select either Recorder Local or UTC.
b
Date/Time Filter - Select Use Filter if required.
c
Select Start and End time and Dates. Results display in Results section.
- End -
126
Video Wall
Introduction
The Video Wall feature uses Client to Client Communication to enable layout components to be sent between
displays attached to different workstations.
Note:
1. Client to Client communication is a licensable feature.
2. Because victor Express is limited to a single client connection, Client to Client communication is not available.
In order to send components to a receiving client, the component must be open on the sending client, therefore the role
of the sender must allow viewing of the layout component. Similarly the receiver’s role must allow viewing of the
component.
Typically, components are sent between workstations using the ‘Send To’ feature of an object's context menu.
Configure Client to Client Communication (Workstations)
Client settings for client to client communication are configured in the workstation editor. These settings determine
how a workstation behaves when a client to client request is sent/received.
There are four main settings:
Setting
Description
Local Removal After Sending
This controls whether components sent from a
workstation remain open on the sender’s
workstation.
Default is On
Turn Off Client to Client Communication
This controls whether a workstation automatically
accepts or rejects requests. When selected,
receiving workstations will not automatically
accept components.
Instead, the sender is informed that the receiving
workstation is configured to reject and asked
whether to force the component.
If the component is forced, the receiver is asked
whether to accept the request and select Yes or
No.
The Sending workstation is informed that the
receivers client to client communication is turned
off in 2 ways:
• A Reject Dialog displays when attempting to
send.
• Receiver’s Name highlights Red.
Default is Off
Maximize on Primary Monitor
This controls whether a received component
displays Full Screen.
Default is On
127
When Using the Send To feature, users need to
navigate to displays via their attached
workstations.
Configuring a workstation as an Agent means the
displays attached to the workstation appear as
local displays in relation to sender’s workstations
so the workstation level is avoided.
Default is Off
Agent
Procedure 21-1 Configure Client to Client Communication
Step Action
1
Select Devices from the Home tab. Device List displays.
2
Select
3
Right Click on the workstation to be edited.
4
Select Edit. Workstation editor displays.
5
Expand the Client to Client Communication section.
6
Select or Deselect the Checkboxes as required to configure the workstation.
7
Select Save.
next to Workstations in the Device List. All workstations are listed.
- End -
Configure Client to Client Communication (Displays)
You can Turn off Client to Client communication for individual displays.
When selected, this option rejects all client to client requests automatically. The sender is informed that the receiver is
configured to reject the request and asked whether to force it. In this case the receiver is asked whether to accept the
request and is presented with a Yes/No dialog.
The sending workstation is informed if a receiving workstation is in Reject mode in two ways:
• A 'Rejecting’ dialog displays next to the display when attempting to send
• The receivers display name highlights red, indicating client to client communication is turned of for that
display
Procedure 21-2 Configure display client to client settings
Step Action
1
Select
next to Workstations in the Device List. All workstations are listed.
2
Select
next to the workstation which is attached to the display to be edited.
3
Select
next to Monitors.
4
Right click the display to be edited.
5
Select Edit. The display editor opens.
6
Expand the Client to Client Communication section.
128
7
Select/Deselect the Turn off Client to Client Communication checkbox as required.
8
Select Save.
- End -
129
Virtual Matrix
Introduction
Virtual Matrix allows users to switch video in display panes of surveillance windows using a CCTV keyboard as if the
video panes were all monitors attached to a traditional analog matrix.
Create a Virtual Matrix Profile
You can define and add virtual matrix profiles to the system.
Procedure 22-1
Create a Virtual Matrix Profile
Step Action
1
Select Virtual Matrix from the Build tab.
2
Select New from the dropdown menu. Virtual Matrix Editor displays.
3
Enter a Name and Description in the General Section.
4
The Enabled checkbox is selected by default, deselect to disable the virtual matrix.
5
Expand the Settings Section. Select checkboxes as required for:
130
• Monitor Number Overlay - Select if monitor numbers are to be displayed in the Virtual
Matrix
• Override User Layout - Select if you require the activation of the Virtual Matrix to close
any existing camera views.
6
Expand the Cameras Section. All available cameras are listed and assigned default virtual numbers.
7
If required, renumber cameras:
To renumber a single camera:
a
Select the camera row
b
Change the virtual number in the renumber cameras textbox
c
Select Selected
d
Repeat as required for subsequent cameras
To renumber a range of cameras
a
Select the renumber cameras textbox
b
Enter the first number of the range to be assigned
c
Select All. Virtual number range updates
8
Expand the Call ups section. All available call ups are listed.
9
If required, renumber call ups:
To renumber a single call up:
a
Select Tours or Salvos tab as required
b
Change the virtual number in the renumber call ups textbox
c
Select Selected
d
Repeat as required for subsequent call ups
To renumber a range of call ups:
10
a
Select the renumber textbox
b
Enter the first number of the range to be assigned
c
Select All. Virtual number range updates.
Expand the Monitors section.
To add monitors:
a
Select
. Dropdown menu displays
b
Select Virtual Display or Analog Matrix as required. Selection displays in monitor list.
Note:
1. When adding an MP48 to a virtual matrix profile, the recorder inputs at the top of the camera list are
automatically moved to the bottom. (You can manually edit the positions.)
2. When adding more than one MP48 analog matrix, it should be noted that the camera inputs of the
second analog matrix will be assigned virtual numbers in the sequence the 'excluded' entries are
unticked.
131
c
Change Video Layout and Workstation as required by double clicking the relevant field and selecting
from the dropdown menu.
d
Repeat as required to add more monitors. (Maximum 4 virtual displays per workstation)
To renumber monitors:
11
a
Deselect the Add monitor ranges automatically checkbox. First pane field becomes a textbox.
b
Assign numbers manually by entering values in the First pane textboxes. Last pane field updates according to the number of panes associated with the selected layouts.
Select Save.
- End -
Renumber Camera Virtual Numbers
The device list orders cameras alphabetically while the virtual matrix builds its camera list when first created. As new
cameras become available they are appended to preserve the virtual numbering.
This means the virtual matrix list of cameras is not always in the same order as the device list.
Virtual camera numbers are labeled 1 through 99999 by default. Individual virtual numbers may be changed or whole
ranges may be assigned new values.
Note:
Keyboards may not be able to call all virtual camera numbers as different keyboards have limits on the highest number
they can recognize.
Renumbering affects the command needed to call up a particular camera, so if you renumber cameras starting at ‘99’,
then to call up the first camera you need 99M+#K.
Procedure 22-2 Renumber Camera Virtual Numbers
Step Action
1
Select Virtual Matrix from the Build tab.
2
Select Show all from the dropdown menu.
3
Right Click the Virtual Matrix to be changed.
4
Select Edit. Virtual Matrix Editor displays.
5
Expand the Cameras section.
To renumber a single camera:
a
Select the camera row
b
Change the virtual number in the renumber cameras textbox
c
Select Selected
d
Repeat as required for subsequent cameras
To renumber a range of cameras
a
Select the Renumber cameras textbox
b
Enter the first number of the range to be assigned
c
Select All. Virtual number range updates
6
Enter the new camera ID in the Renumber Cameras text box.
7
Select Save.
132
- End -
133
Renumber Call ups in a Virtual Matrix
You can renumber the default numbers assigned to call ups in a virtual matrix either individually or by range.
Procedure 22-3 Renumber Call ups in a Virtual Matrix
Step Action
1
Select Virtual Matrix from the Build tab.
2
Select Show all from the dropdown menu.
3
Right Click the Virtual Matrix to be changed.
4
Select Edit. Virtual Matrix editor displays.
5
Expand the Call ups section.
6
Select Tours or Salvos as required.
To renumber a single call up:
a
Select the call up row
b
Change the virtual number in the renumber textbox
c
Select Selected
d
Repeat as required for subsequent call ups
To renumber a range of call ups
7
a
Select the Renumber textbox
b
Enter the first number of the range to be assigned
c
Select All. Virtual number range updates
Select Save.
- End -
134
Edit Monitors (Virtual Matrix)
You can add and remove monitors from virtual matrices. A maximum of 4 virtual displays can be added to each
workstation.
Procedure 22-4 Edit Monitors (Virtual Matrix)
Step Action
1
Select Virtual Matrix from the Build tab.
2
Select Show all from the dropdown menu.
3
Right click the virtual matrix to be edited.
4
Select Edit.
5
Expand the Monitors section.
To add Monitors:
a
Select
. Dropdown menu displays
b
Select Virtual Display or Analog Matrix as required. Selection displays in monitor list.
c
Change Video Layout and Workstation as required by double clicking the relevant field and selecting
from the dropdown menu.
d
Repeat as required to add more monitors. (Maximum 4 virtual displays per workstation)
To remove monitors:
a
Highlight the monitor row.
b
Select
. Monitor is removed
To renumber monitors:
a
Deselect the Add monitor ranges automatically checkbox. First pane field becomes a textbox.
b
Assign numbers manually by entering values in the First pane textboxes. Last pane field updates according to the number of panes associated with the selected layouts.
To change Video Layouts:
a
Double click the video layout of the display to be changed. Available video layouts display.
b
Select the required layout. Video layout and pane numbers update.
To change monitor workstation:
6
a
Double click the workstation name of the virtual display. List of available workstations displays.
b
Select workstation as required.
Select Save.
- End -
135
Analog Matrix
Introduction
You can add Megapower 3200 and MegaPower 48 Plus analog matrices to the system. Each matrix can specify one
or more workstations to which they are serially connected. Once added to the system, the matrices will be available
for inclusion in virtual matrix profiles so they can be controlled from a particular workstation via an attached keyboard.
Once the matrix has been added to the system, it will be displayed along with other system devices in the Device List.
A typical analog matrix configuration will have video feeds to the matrix coupled to a recorder which may already be
part of the victor system. With this setup the virtual matrix allocates a camera Id to both the recorder camera and the
analog matrix input.
Camera mapping is required to allow playback from keyboard "Orange Buttons"; when the user selects a camera
associated with the analog matrix this will allow the virtual matrix to identify its associated recorder if one is available
and take the appropriate action to retrieve the clip and playback the video or signal an invalid operation.
Analog Matrix Editor
Using the Analog Matrix editor you can configure basic matrix properties via the General and Analog Matrix Setup
sections.
The Workstation Connections section is used to configure the COM Port, Baud Rate and Playback Monitor specific
settings for each workstation matrix connection. Remote workstations can be dragged and dropped here from the
Device List.
The Inputs and Analog Matrix Playback Configuration section of the editor is used to configure camera mappings.
Camera mappings are required to enable playback from keyboard ‘Orange Buttons’.
To configure the camera mappings, video streams which are already present on the victor system via a recorder are
dragged from the device list onto the Analog Matrix editor "Camera Mapping" list. To manipulate the sequence of the
list, delete, move up and move down functionality is available via a toolbar and context menu.
Satellite Sites - The MP3200 allows a satellite site configuration permitting a site to access the resources of one or
more remote sites. This feature is not available on MP48 nor MP48+ matrices.
Before adding an analog matrix it should be correctly configured via its supporting configuration application (EasyCPU
for MP3200 and Easy 48 for MP48).
Note:
1. Any video stream and monitor resources configured during the victor setup are always considered available to the
associated victor workstation.
2. Once an Analog Matrix has been added to victor, the victor workstation will always expect it to be available, no
attempt will be made to poll the device for status.
136
Sites
Any cameras not associated with an Analog Matrix are assigned to Site "0".
The following keyboards do not allow for the calling of site '0':
• ADCC200
• ADCC300
• ADCC1100
For these models, you can use the keyboard's context menu Return to Home option to switch to site0.
Create an Analog Matrix
Users can define and add a analog matrices to the system using the Analog Matrix editor.
Procedure 23-1 Create and Analog Matrix
Step Action
1
Select Analog Matrix from the Setup tab.
2
Select New from the drop down list.
3
In the General section enter a name in the Name text box.
4
Enter a description in the Description text box.
5
The Enabled checkbox is selected by default. To disable the Analog Matrix, deselect the checkbox.
6
Expand the Analog Matrix Setup section. Select the model to be added:
• MegaPower 3200
Or
• MegaPower 48
7
Enter the Site number in the Site textbox.
Note:
Sites textbox is only available if MP3200 has been selected at Step 6.
8
Enter the number of cameras in the Camera Count textbox.
9
Enter the number of monitors in the Monitor Count checkbox.
10
Enter a Username in the Username textbox.
11
Enter a password in the Password textbox.
12
Check the Requires Authentication checkbox if you require users to authenticate before accessing the analog
matrix.
13
Expand the Workstation Connections section. Use this section to configure workstations associated with the
analog matrix.
14
Select the workstation to attach the analog matrix to. (The current workstation is automatically added to the
connection list along with default values for COM port, Baud rate and Playback Monitor, to add further remote
workstations, drag them from the device list as required.)
137
15
Double click default COM port and select an alternative from the dropdown if required.
Note:
1. If a COM port is already in use by another device, it will appear as greyed out in the drop down list.
You can see which device is using the COM port by viewing the tooltip.
2. Select Blank to have no COM port assigned.
16
Double click default Baud Rate and select an alternative from the dropdown if required.
17
Double click default Playback Monitor and select alternative from the dropdown if required.
18
Double click default value for Playback to Analog Matrix.
19
Select or deselect the Enabled checkbox to enable or disable the feature.
20
Enter the Matrix Input value in the Matrix Input textbox.
21
Add further remote workstations by dragging and dropping them from the Device List onto the Connection
List.
22
Configure remote workstations as required (Refer to Steps 13-20 above).
23
Expand Inputs and Analog Matrix Playback Configuration Section. Use this section to configure camera
mappings and assign Pseudo numbers to analog inputs.
24
Associate video feeds as required by dragging cameras or recorders from the device list into the Inputs
Configuration list.
25
Expand the Satellite Sites section.
26
Drag required Satellite Sites from the Device list into the Satellite Sites list in the editor.
27
Select Save.
- End -
Edit Analog Matrix - General/Setup Properties
You can make changes to general properties of an Analog Matrix. Editable properties include Name, Description,
Enabled/Disabled, Model, Camera Count and Monitor Count.
Procedure 23-2 Edit Analog Matrix
Step Action
1
Select Analog Matrix from the Setup tab.
2
Select Show all from the drop down menu.
3
Right click the Analog Matrix to be edited.
4
Select Edit. Analog Matrix editor displays.
5
Expand the General section if changes are to be made.
6
Make edits as required to:
• Name
• Description
• Enabled (Check or uncheck Checkbox)
7
Expand Analog Matrix Setup if changes are to be made.
138
8
Make edits as required to:
• Model (Select from dropdown)
• Site (Numerical value only)
• Camera Count (Numerical Value only)
• Monitor Count (Numerical Value Only)
• Username
• Password
• Requires Authentication (Check or uncheck checkbox)
9
Select Save.
- End -
Edit Analog Matrix - Add/Remove/Edit workstation connections
You can add/remove workstations associated with the matrix as well as change the COM Port, Baud rate and
Playback Monitor of specific workstations.
Procedure 23-3 Edit Analog Matrix - Add/Remove/Edit workstation connections
Step Action
1
Select Analog Matrix from the Setup tab.
2
Select Show all from the drop down menu.
3
Right click the Analog Matrix to be edited.
4
Select Edit. Analog Matrix editor displays.
5
Expand the Workstation Connections section.
6
To Add a remote workstation to the list:
7
8
9
a
Select the Workstation in the Device List.
b
Drag the workstation to the Workstation Connections list.
c
Release the workstation. The list updates to include the new remote workstation.
To Edit properties of a workstation:
a
Double click the value to be changed.
b
Select the new value from the drop down list. Value updates to the new selection.
To Remove a workstation from the list:
a
Select the workstation to be removed.
b
Right Click the workstation.
c
Select Remove ‘Workstation Name’. Workstation list updates.
Select Save.
- End -
139
Edit Analog Matrix - Configure Inputs
You can configure camera mappings and associations within the Analog Matrix editor. Camera mappings are required
to enable playback from keyboard ‘Orange Buttons’.
Procedure 23-4 Edit Analog Matrix - Configure Inputs
Step Action
1
Select Analog Matrix from the Setup tab.
2
Select Show all from the drop down menu.
3
Right click the Analog Matrix to be changed.
4
Select Edit. Analog Matrix editor displays.
5
Expand the Inputs Configuration section.
6
Drag video feeds from the device list as required and drop them into the list. You can drag recorders or
cameras into the list.
a
Drag a video stream (Camera OR Recorder) from the device list and drop it in the inputs list. The list populates with the video streams.
b
If required, renumber the default Pseudo Numbers.
• To renumber a single input:
a
Select the cell containing the Pseudo number to be changed.
b
Enter the new number in the textbox at the top of the section between the All and Selected buttons.
c
Select Selected. The new number displays in the Pseudo number list.
• To renumber all inputs:
a
Enter the first number of the new range in the textbox at the top of the section between the All and Selected buttons.
b
Select All. All numbers change to the new selection.
7
You can edit the sequence of the list as well as change video streams by using the list’s context menu.
8
Select Save.
- End -
Add/Remove satellite sites
Satellite Sites - The MP3200 allows a satellite site configuration permitting one site access to the resources of one or
more remote sites. This feature is not available on MP48 nor MP48+ matrices.
Procedure 23-5 Add/Remove satellite sites
Step Action
1
Select Analog Matrix from the Setup tab.
2
Select Show all from the drop down menu.
3
Right click the Analog Matrix to be edited.
140
4
Select Edit.
5
Expand the Satellite Sites section.
6
To Add a Satellite Site:
7
a
Select the Analog Matrix from the Device List.
b
Drag and Drop the Analog Matrix from the Device List into the Satellite Site list.
Select Save.
- End -
Reconnect to an Analog Matrix
You can reconnect to an Analog Matrix if a connection has been broken, without needing to edit the properties of the
Analog Matrix.
Procedure 23-6 Reconnect to an analog matrix
Step Action
1
Select Devices from the Home tab. Device List displays.
2
Select next to Analog Matrices in the Device List window. All analog matrices are listed.
3
Right click the Analog Matrix that needs to be reconnected.
4
Click Reconnect. The analog matrix is reconnected.
Note:
The Reconnect option will be disabled if the analog matrix is disabled, or, if the local workstation
details are incorrect in the Workstation Connections section.
- End -
141
Controllers
Introduction
Various CCTV Keyboards, Multimedia Controllers and Joysticks are supported in victor for surveillance control.These
can be used to navigate and switch video streams in display panes of surveillance windows and virtual matrices.
Serial keyboards have fixed functionality within the victor surveillance environment whereas Joysticks,Gamepads
and other Multimedia controllers are configurable.
Controller button configuration (General Information)
Some controllers are 'Plug and Play', others support configuration within victor, see below:
Controller Device
Button configuration options
AD/Pelco Serial Keyboards
Not Applicable: Refer to manufacturer's instructions for
default settings.
System Keyboard (Standard QWERTY)
Not Applicable: Refer to System Keyboard Commands for
default settings.
ExacqVision Keyboards (VM Desktop Model 100-590-2130)
Via victor Client: Keyboards>Joystick Configuration.
Axis 295 Video Surveillance Joystick
Axis T8311 Video Surveillance Joystick
Via victor Client: Keyboards>Joystick Configuration.
Gamepads
Via victor Client: Joystick>Gamepad Configuration (refer to
Gamepad controller configuration
ShuttlePRO v2
Not Applicable. Refer to ShuttlePRO v2 controller for
default settings.
142
System Keyboards
You can add a standard Windows keyboard and use it as a CCTV keyboard.
Note:
When using a system keyboard, surveillance commands can only be sent if the surveillance window has focus. Other
controllers will operate regardless of whether the surveillance window has focus.
Refer to System Keyboard Commands for a list of user commands.
Procedure 24-1 Add a System Keyboard
Step Action
1
Select Keyboards from the Setup tab.
2
Select New from the dropdown.
3
Enter a name for the keyboard in the Name textbox.
4
Enter a description for the keyboard in the Description textbox.
Note:
The Enabled checkbox is checked by default, deselect the checkbox to deactivate the keyboard.
5
Expand the Keyboard section.
6
Select System Keyboard from the Model dropdown. The COM Port and Baud Rate dropdown lists
disappear.
7
Select Save.
- End -
System Keyboard Commands
When using a system (QWERTY) keyboard, the following commands are available:
Command
Action
Arrow Keys
Pan/Tilt
w
Stop
Number Pad Arrow
Keys
Pan/Tilt
e
Pause
+/- (Number Pad)
Zoom in/Out
r
Play
-/=
Zoom in/Out
t
Fast Forward
#m
Monitor (# is a number: 1-999)
s
Jump to Date (4 digits in month/day format)
#k
Camera (# is a number: 1-9999)
d
Jump to Time (4 digits in 24 hour format)
q
Rewind
#s
Site
143
Command
Action
Serial Keyboards
Any of the listed AD/Pelco keyboards can be used in victor.
Procedure 24-2 Add an AD/Pelco Keyboard
Step Action
1
Select Keyboards from the Setup tab.
2
Select New from the dropdown.
3
Enter a name for the keyboard in the Name textbox.
4
Enter a description for the keyboard in the Description textbox.
Note:
The Enabled checkbox is checked by default, deselect the checkbox to deactivate the keyboard.
5
6
Expand the Keyboard section.
a
Select the required Model from the dropdown.
b
Select the required COM Port from the dropdown.
c
Select the required BAUD Rate from the dropdown.
Select Save.
- End -
System/Serial Keyboards: Supported functionality
Serial Keyboards
Feature
System
ADTTE
AD
2088/89
ADC0200
ADC0300
ADC1100
Pelco
KBD300A*
Camera/Monitor Call up
ü
ü
ü
ü
ü
ü
ü
Standard PTZ Control
ü
ü
ü
ü
ü
ü
ü
ü
Keyboard Macros
ü
Salvos
ü
ü
ü
ü
ü
Tours
ü
ü
ü
ü
ü
Patterns
ü
ü
Presets
ü
ü
ü
ü
ü
ü
Focus/Iris Control
ü
ü
ü
ü
ü
ü
Flip
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
Site
ü
Keyboard Functionality**
*Using ASCII protocol (Pelco Keyboard requires an RS422-RS-232 converter)
144
** See Keyboard/Matrix Switcher Manual for specific functionality
Note:
1. When using a system keyboard, commands can only be sent if the surveillance window has focus. Other
keyboards are not affected and will continue to operate whether the surveillance window has focus or not.
2. System keyboards cannot be edited from remote clients.
3. Repeat should be set to ‘Off’ for all keyboards. Refer to the keyboard user documentation for instructions.
American Dynamics Serial Keyboard Installation
Wiring diagrams for installing keyboards:
AD2088, AD2089, ADTTE, ADCC1100 ADCC200, ADCC300
AD2088 and AD2089
Note:
To install the AD2088 and AD2089 Keyboard, you require the Keyboard PC kit (ADACKBPC2000)
145
ADTTE
Note:
To install the ADTTE Keyboard, you require the Keyboard PC kit (ADACKBPC2000)
146
ADCC100 or ADCC0200/0300
Note:
To install the ADCC100 or ADCC200/300 Keyboards, you require the Keyboard PC kit (ADACKBPCMPCC)
There are three Methods of connecting ADCC100 or ADCC0200/0300:
• Method 1
• Method 2
147
• Method 3
148
Joystick/Gamepad configuration
ExaqVision controllers configuration
ExaqVision Default button assignments
Note:
1. '#' Button is not configurable
2. Number pad keys are not configurable
Button
Action
Button
Action
C1
Select/Execute
C9
Hold tour
C2
Go back
C10
Flip 180°
C3
Open/Close OSD
C11
Stop
C4
Next tab
C12
Toggle Play/Pause
C5
Previous monitor
C13
Clear
C6
Next monitor
14
*Monitor
C7
Focus near
15
Last camera (Left joystick button)
C8
Focus far
16
Next Camera (Right joystick button)
Exaqvision controllers keyboard mapping can be configured within victor:
Procedure 24-3 ExaqVision controllers: victor Configuration
Step Action
1
Select Keyboards from the Setup tab.
2
Select Joystick Configuration from the dropdown.
3
Select ExaqVision Surveillance Keyboard from the Load Preset Configuration dropdown.
4
Select Supports Numeric Input if required.
5
Select Apply.
6
Expand the controller Controller Layout section:
X/Y Axis
a
Use the Dead Zone slider bar on the X/Y axis section to set the number of pixels which the thumbstick
needs to traverse before becoming active (the larger the dead zone, the less sensitive the controller)
b
Select Invert Y Axis if required (Reverses the default'Y' orientation- Up becomes Down, Down
becomes Up)
c
Select Control assignment for X/Y axis- either Pan/Tilt or leave unassigned
Z Axis
149
d
Use the Dead Zone slider bar on the Z axis section to set the number of pixels which the thumbstick
needs to traverse before becoming active (the larger the dead zone, the less sensitive the controller)
e
Select Invert Z Axis if required (Reverses the default'Z' orientation)
f
Select Control assignment for Z axis- select Zoom, Focus, Iris, Playspeed or leave unassigned
X Position
7
g
Adjust the X position using the outer jog wheel. Use the Dead Zone slider bar to set the number of pixels
which the jog wheel needs to traverse before becoming active
h
Select X Position if required
i
Select Control assignment for X Position either Pan/Tilt, Zoom, Iris, Playspeed or leave unassigned
Expand the Keyboard Mapping section.
a
8
Use Press Key Here field to map supported virtual keyboard buttons.
Select Save.
- End -
150
Axis controller configuration
victor supports the Axis T8310 Video Surveillance control board. This consists of three units that can be installed
separately or together as one unit.
• T8311 Video Surveillance Joystick (Control PTZ functionality of cameras): Configurable in victor
• T8312 Video Surveillance Keypad (Navigate between cameras, views and presets) Not Configurable
• T8313 Video Surveillance Jog Dial (Jog and shuttle through recorded video) Not Configurable in victor
Axis T8311 Default button assignments
Button
Default Assignment
Button
Default Assignment
1
Select/Execute
4
Go back
2
Open/Close OSD menu
5
Next tab
3
Previous monitor
6
Next monitor
Axis T8311 controller keyboard mapping can be configured within victor:
Procedure 24-4 Axis Joystick: victor configuration (T8311)
Step Action
1
Select Keyboards from the Setup tab.
2
Select Joystick Configuration from the dropdown.
3
Select the Axis T8311 joystick from the Load Preset Configuration dropdown.
4
Select Supports Numeric Input if required.
5
Select Apply.
6
Expand the controller Controller Layout section:
X/Y Axis
a
Use the Dead Zone slider bar on the X/Y axis section to set the number of pixels which the thumbstick
needs to traverse before becoming active (the larger the dead zone, the less sensitive the controller)
b
Select Invert Y Axis if required (Reverses the default'Y' orientation- Up becomes Down, Down
becomes Up)
c
Select Control assignment for X/Y axis- either Pan/Tilt or leave unassigned
Z Axis
d
Use the Dead Zone slider bar on the Z axis section to set the number of pixels which the thumbstick
needs to traverse before becoming active (the larger the dead zone, the less sensitive the controller)
e
Select Invert Z Axis if required (Reverses the default'Z' orientation)
f
Select Control assignment for Z axis- select Zoom, Focus, Iris, Playspeed or leave unassigned
7
Change default button assignments using the dropdown menus.
8
Expand the Keyboard Mapping section.
151
a
Use Press Key Here to map supported virtual keyboard buttons.
b
Use the Keyboard Mapping section, to map the controller keyboard to system commands.
Note:
To aid with key mapping, each keystroke on the controller highlights red on the GUI
9
Select Save.
- End -
victor supports the Axis 295 Video Surveillance control board.
Axis 295 Default button assignments
Button
Default Assignment
Button
Default Assignment
1
Go Back
7
Rewind
2
Clear
8
Fast Forward
3
Previous tab
9
Previous monitor
4
Next tab
10
Next monitor
5
Play/Pause
11
Open/Close OSD
6
Stop
12
Select/Execute
Axis 295 controllers can be configured within victor:
Procedure 24-5 Axis Joystick: victor configuration (Axis 295)
Step Action
1
Select Keyboards from the Setup tab.
2
Select Joystick Configuration from the dropdown.
3
Select the Axis 295 joystick from the Load Preset Configuration dropdown.
4
Select Apply.
5
Expand the controller Controller Layout section:
X/Y Axis
a
Use the Dead Zone slider bar on the X/Y axis section to set the number of pixels which the thumbstick
needs to traverse before becoming active (the larger the dead zone, the less sensitive the controller)
b
Select Invert Y Axis if required (Reverses the default'Y' orientation- Up becomes Down, Down
becomes Up)
c
Select Control assignment for X/Y axis - either Pan/Tilt or leave unassigned
Z Axis
6
d
Use the Dead Zone slider bar on the Z axis section to set the number of pixels which the thumbstick
needs to traverse before becoming active (the larger the dead zone, the less sensitive the controller)
e
Select Invert Z Axis if required (Reverses the default 'Z' orientation)
f
Select Control assignment for Z axis- select Zoom, Focus, Iris, Playspeed or leave unassigned
Expand the Keyboard Mapping section.
a
Use Press Key Here to map supported virtual keyboard buttons.
152
b
Use the Keyboard Mapping section, to map the controller keyboard to system commands.
Note:
To aid with key mapping, each keystroke on the controller highlights red on the GUI
7
Select Save.
- End -
153
Gamepad controller configuration
victor supports gamepad 'Plug and Play' functionality meaning there is no requirement to 'Add' the controllers in victor.
Gamepad controller default button assignments.
Button
Default Assignment
Right shoulder
Next monitor
Left shoulder
Previous monitor
Left stick (Move)
Pan/Tilt
Left Stick (Press)
Open/Close OSD menu
Right Stick (Move)
Move mouse
Right Stick (Press)
Mouse left click
Directional Pad Up
Toggle Play/Pause
Directional Pad Down
Stop
Directional Pad Left
Rewind
Directional Pad Right
Fast Forward
X
Mouse right click
Y
Flip 180°
B
Go back
A
Select/Execute
Left Trigger
Zoom in
Right Trigger
Zoom out
Gamepad controllers can be configured within victor:
Procedure 24-6 Gamepads: victor configuration
Step Action
1
Select Keyboards from the Setup tab.
2
Select Gamepad Configuration.
3
Expand the Controller Layout section.
4
For Left and Right Thumb Axes configuration:
5
a
Use the Dead Zone slider bar to set the number of pixels which the thumbstick needs to traverse before
becoming active (the larger the dead zone, the less sensitive the controller)
b
Select Invert Y Axis if required (Reverses the default 'Y' orientation - Up becomes Down, Down
becomes Up)
c
Use the Control Assignment pulldown to define the functionality of the thumbstick (E.G., Mouse Control or Pan/Tilt control)
Use the Button Assignments control to map the controller's physical buttons to victor surveillance actions.
154
Note:
Default actions are assigned to the controller buttons; these are appended with (Assigned) in the
dropdown assignment lists
6
7
Left/Right Trigger configuration (underside of the controller: LT/RT):
a
Assign a Dead Zone up to 255 pixels using the slider
b
Assign the button
c
Use the Control Assignment pulldown to define the functionality of the trigger buttons
Direction Pad Configuration:
a
8
Use the Dropdown menus to assign actions against Up, Left, Right and Down commands.
Select Save.
- End -
155
ShuttlePRO v2 controller
ShuttlePRO v2 is a multimedia controller which works within any computer application with keyboard commands.
To enable ShuttlePro support in victor you should:
1
Install ShuttlePro V2 software (provided with the ShuttlePro product).
2
Run the Contour Shuttle Device Configuration utility.
3
Use the utility's Settings Management section to import victor.pref file from C:\Program
Files\Tyco\victorClient\Config\victor_shuttlepro.pref
4
Select OK. ShuttlePro controller will be ready to use.
victor has been developed to provide ShuttlePRO v2 support natively; there is therefore no need for configuration
within the victor environment.
ShuttlePro V2 Default button assignments:
156
Configuring Patterns and Presets using numeric input USB Keyboards
The keyboard should be configured for use with victor.
Procedure 24-7 Keyboards: Configuring Patterns using numeric USB keyboard
Step Action
1
Select the Setup tab.
2
Select Keyboards.
3
Select Joystick Configuration.
4
Configure one of the Button Assignments for the keyboard to ‘Set Pattern’. Refer to the victor Administration
and Configuration guide if further help if required.
5
Program a pattern using the USB joystick:
6
a
Input a pattern number on the numeric keypad of the USB Joystick.
b
Press the Joystick button which has the ‘Set Pattern’ assignment, this will begin the programming process.
c
Using the joystick, pan tilt and zoom to define the pattern and then press the ‘Set Pattern’ button again to
save the defined pattern and close out of programming mode.
To run the pattern, input a pattern number on the numeric keypad of the USB Joystick and then press the
Joystick button which has the "Run Pattern" assignment
- End -
Procedure 24-8 Keyboards: Configuring Presets using numeric USB keyboard
Step Action
1
Select the Setup tab.
2
Select Keyboards.
3
Select Joystick Configuration.
4
Configure one of the Button Assignments for the keyboard to ‘Set Preset’. Refer to the victor Administration
and Configuration guide if further help if required.
5
Program a preset using the USB joystick:
6
a
Pan, Tilt and Zoom to the region where the preset is to be programmed.
b
Input a preset number on the number pad of the USB joystick.
c
Press the joystick button which has the ‘Set Preset’ assignment.
d
Repeat as required.
To run the preset, input a preset number on the numeric keypad of the USB Joystick and then press the
Joystick button which has the ‘Run Preset’ assignment.
- End -
157
Layouts
Introduction
The default victor unified client layout consists of three tabbed toolbars (Home, Build and Setup), the Device List
and a 2X2 Surveillance tab. This layout can be completely customized, allowing you to create a workspace that better
suits the requirements of individual operators and roles.
Note:
The Ribbon controls are minimized by default. To show the controls, double click the Home, Build or Setup tab
Window Types
Various window types are supported within victor. Type changes and behavior can be accessed by right clicking the
window title bar. victor unified client supports 3 window types:
Floating Windows
Creates a window that is independent of the client window. A floating window can be moved to anywhere on screen,
resized and reshaped to suit your workspace.
Dockable
Creates a window that can be docked into position within the main client window. When a dockable window is
dragged, a guide diamond is displayed (see below), allowing you to quickly dock it on one of the four sides of the
workspace. When a docked window is undocked, it will float to the top of other windows.
Tabbed
Creates a window that appears in a tab. Tabbed windows are useful for organizing and switching between multiple
open windows.
158
Configuring your Workspace
You can create a custom layout to suit your individual workspace.
Procedure 25-1 Dock Window
Step Action
1
Right click the title bar or tab of the window.
2
Select Dockable.
3
Drag the window to the middle area of the screen. The Guide diamond displays.
4
Hover the cursor over the guide diamond arrow which corresponds with the area you want to dock the window
in. Area highlights.
5
Release the mouse, Window docks in position.
- End -
Procedure 25-2 Resize Windows
You can resize a docked or floating window to provide more or less area in the workspace.
Step Action
1
If the window is tabbed, right click the title bar and select Floating or Dockable.
2
Hover the cursor over the corner side of the window. Grab Handles display
3
Select and drag the cursor to resize the window as required.
.
- End -
Procedure 25-3 Autohide Windows
Autohide is only available in dockable windows that have been docked.
When Autohide is enabled on a window, it will only be visible as a tab when it does not have focus. This means that
the window is open and can be easily accessed, but the area it occupies is greatly reduced.
Step Action
1
Right click the title bar of the docked window.
2
Select Autohide. The window will reduce to a tab view positioned according to the docked attribute of the
window.
3
Select the tab to view the window or remove focus to autohide.
- End -
159
Procedure 25-4 Show/Hide the Ribbon
You can Minimize or maximize the ribbon controls to create more workspace. This change is not saved as a layout
change.
Note:
Default setting is minimized
Step Action
1
Double click the Home, Build or Setup tab. Ribbon is displayed.
2
Double click the Home, Build or Setup tab. Ribbon is hidden.
- End -
Save / Switching Layouts
Save
Once your workspace has been configured to suit your requirements, you can save the layout for later retrieval.
Procedure 25-5 Save Current Layout
Step Action
1
Select Layout on the Build tab.
2
Select Save as from the dropdown menu. Name textbox displays.
3
Enter a name for the new layout.
4
Select OK. The layout is saved.
Note:The default layout cannot be deleted.
- End -
Switch
Procedure 25-6 Switch to Saved Layout
Step Action
1
Select Switch on the Home tab. List of layouts displays.
2
Select the layout from the dropdown menu. New layout displays.
- End -
160
Switch on Primary
The Switch On Primary feature allows you to set a new layout to be displayed on the primary monitor only.
Note:
All tabbed, dockable and floating windows are considered part of your primary display, regardless of which monitor
they reside on.
Procedure 25-7 Layout - Switch on Primary
Step Action
1
Select Switch On Primary from the Build tab
2
Select a layout from the dropdown menu. The new layout is applied to the primary monitor only
- End -
Layout Groups
Layout Groups allow layouts to be loaded onto client machines remotely.
Procedure 25-8 Create Layout Group
Step Action
1
Select Layout Group from the Build tab
2
Select New from the dropdown menu. The Layout Group editor opens
3
Select the Name textbox and enter a name
4
If required, select the Description text box and enter a description
5
Drag required layout to the required workstation(s)
6
Select Save
- End -
Procedure 25-9 Load Layout Group
Step Action
1
Select Switch Group from the Home tab
2
Select the required layout from the dropdown list. Selecting a layout will switch the configured layout to all
workstations specified in the layout group
Note:
1. Layout Groups will remain assigned to workstations until the layout is deleted or another layout
selected
2. Layout groups override selection from Switch on Primary or Switch
- End -
161
Refresh Layouts
Various options are available to refresh layouts from the Home tab.
Procedure 25-10 Refresh Layouts
Step Action
1
Select Refresh from the Home tab.
2
Select from dropdown options.
• Refresh Layout
• Refresh on Primary
• Refresh Group Layout
- End -
Rename Tabbed Window
Tabbed windows can be renamed. Any renaming will be saved when the layout is saved.
Procedure 25-11 Rename Tabbed Windows
Step Action
1
Right Click the tab to be renamed.
2
Select Rename. Name dialog displays.
3
Enter a new name for the tab.
4
Select OK.
- End -
Create New Tab Groups
You can create new tab groups for convenient grouping and navigation of windows. To create tab groups, more than
one tab must be open.
Procedure 25-12 Create New Tab Groups
Step Action
1
Right Click on the tab to start the new group. This will be the first tab listed in the group.
2
Select New Horizontal Tab Group or New Vertical Tab Group as required. New group is created per the
selection.
Note:
1. Reorder tabs within groups by selecting and dragging tabs within the group.
162
2. Move tabs between groups by right clicking the tab and selecting Move to Previous/Next Tab
Group.
- End -
Merge Docked Windows
You can merge docked windows to create more on-screen workspace. Merged windows are grouped together as a
single tabbed screen element.
Procedure 25-13 Merge Docked Windows
Step Action
1
Select the title bar of a docked window.
2
Drag to the centre of the docked window to which it is to merge. The docking icon displays.
3
Deselect the window in the centre of the docking icon. Windows merge. Navigate the windows by selecting
appropriate tabs from the bottom of the merged window.
- End -
View Window In Full Screen
You can view any window in full screen mode.
Procedure 25-14 View Window Full Screen
Step Action
1
Right click the title bar of the window.
2
Select Send To from the context menu.
3
Select the display in which to view the full screen window.
- End -
Save and Restore Current Layout
Selecting the save layout option saves the current layout. Once your workspace is arranged, you can save the layout
under a descriptive name and restore it later.
Procedure 25-15 Save Current Layout
Step Action
1
Select Layout
2
Select Save. The Choose save location dialog opens
3
Navigate to the location you wish to save the layout to
163
4
Enter a File Name
5
Select Save
- End -
Procedure 25-16 Restore Layout
Step Action
1
Select Layout
2
Select Load. The Select layout file to open dialog displays
3
Navigate to saved layout file location and select required layout file
4
Select Open. The surveillance window updates with the restored layout
- End -
164
Workstations
Introduction
Workstations refer to the machines running victor client software. They display by default on the device lists of client
machines and are editable via Workstation editors.
From the editor you can configure workstation descriptions and Client to Client Properties.
Context menu options specific to workstations include the ability to Logout Local Operators, Logout Remote
Operators, Delete Workstations, Identify Monitors.
Identify Monitors
You can use the Identify Monitors feature to display the names of all monitors associated with each client workstation.
Monitor names are displayed on screen for 3 seconds after making the selection.
Procedure 26-1 Identify Monitors
Step Action
1
Select
next to Workstations in the Device List. All workstations are listed.
2
Right Click the required workstation.
3
Select Identify Monitors. Display Names display for 3 seconds on all monitors attached to that workstation.
- End -
Operator Logout (Remote)
You can use the context menu of workstations listed in the device list to remotely log out operators.
Procedure 26-2 Operator Logout (Remote)
Step Action
1
Select
next to Workstations in the Device List. All workstations are listed.
2
Right Click the required workstation.
3
Select Log Operator XXXX Out. Warning dialog displays.
4
Select Yes to log the operator out or No to cancel.
- End -
165
Rename Displays
Default display names are Display 1,2,3 etc. You can edit the default names as required.
Procedure 26-3 Rename Displays
Step Action
1
Select
next to Workstations in the Device List. All workstations are listed.
2
Select
next to the workstation which is attached to the display to be renamed.
3
Select
next to Monitors.
4
Right click the display to be renamed.
5
Select Rename. Textbox displays.
6
Enter a new name for the display.
7
Select OK.
- End -
Delete Displays
You can delete displays from workstations. Deleted displays will no longer appear as options when using the Send To
function.
Procedure 26-4 Delete Displays
Step Action
1
Select
next to Workstations in the Device List. All workstations are listed.
2
Select
next to the workstation which is attached to the display to be deleted.
3
Select
next to Monitors.
4
Right Click the display to be deleted.
5
Select Delete. A Warning dialog displays.
6
Select Yes to Delete or No to Cancel.
- End -
166
Point of Sale
Introduction
Point-of-Sale (POS) systems are used to facilitate and record financial transactions between businesses and
customers. Most commonly they are used in retail environments for product sales.
victor incorporates a comprehensive set of POS integration features which are available as a licensed add-on.
Using the victor unified client you can import two types of POS data: raw POS transactions from your POS system,
and POS exception reports produced by your POS exception reporting system.
Once POS data is imported into victor, a range of investigation tools are available. You can access video of each
transaction, and use victor’s video investigation tools, such as Investigator Mode and Clip Export to gather video
evidence. In addition victor provides advanced POS searching capabilities which can use to find specific transactions
based on predefined POS rules.
Configuration
Before using victor’s POS features, several configuration steps should be followed:
The most important aspect of this configuration is to identify which cameras record video of which POS terminals (or
cash registers). This is achieved creating POS terminal objects in victor, and associating those with camera objects.
The steps involved are:
1
Create a POS Store object
2
Create POS Terminal objects
3
Associate POS Terminals with relevant cameras
After these general steps are complete, victor is ready to import POS data. When POS data is imported, it is
automatically synchronized with video based on Time (See POS Time Offset) and Terminal ID with camera
associations. This means operators are not required to know or remember which cameras cover which terminals and
are not required to manually enter dates/times to view POS transactions or exceptions.
Camera Region Editor
The Camera Region Editor provides a means to visually identify areas within a camera view which are represented by
Customers, Merchandise, Employees and Terminals.
While not specifically a POS feature, making associations between cameras with defined regions and edge devices
allows users to view pertinent regions of camera views when triggers are initiated from the associated items. This can
be particularly useful in a retail environment.
167
UnifiedPOS Data Import
Raw POS transactions are imported into victor in standard UnifiedPOS XML format. The UnifiedPOS XML format was
developed by the National Retail Federation (NRF) Association for Retail Technology Standards (ARTS). The format
is a public standard for exchange of POS data in an XML form. See your POS system documentation or contact your
POS system vendor to determine how you can export UnifiedPOS data for use with victor.
Caution
Before importing POS data into victor you should remove or securely obscure any sensitive credit card information.
victor has not been certified for PCI DSS compliance.
This chapter details how to:
• Create a POS Store
• Create POS Terminals
• Associate Terminals with Cameras
• Define Camera Regions
• Import POS Transactions
• Search POS transactions
• View POS Transactions
• Import POS Exception Reports
• View POS Exception Reports
Create a POS Store
You can create POS store objects within victor client. These objects can be associated with multiple terminal objects.
Procedure 27-1 Create a POS Store
Step Action
1
Select Store from the Setup tab.
2
Select New from the dropdown.
3
Enter a Name for the POS Store in the Name textbox.
4
Enter a Description for the POS Store in the Description textbox.
5
Enter the RetailStoreID.
Note:
The RetailStoreID must match the ID used by the POS system or no transactions will be imported.
6
Select Save.
- End -
168
Create POS Terminal Objects
You can create one or more POS Terminals within victor. These are then typically associated with cameras which
have fields of view covering the POS terminals.
Procedure 27-2 Create POS Terminal Objects
Step Action
1
Select Terminal from the Setup tab.
2
Select New from the dropdown.
3
Enter the Store to be associated with the terminal.
4
Enter a Name for the Terminal in the Name textbox.
5
Enter a Description for the Terminal in the Description textbox.
6
Enter the WorkstationID.
7
Select Save.
Note:
The WorkstationID should match the ID used by your POS system for this terminal or no
transactions will be imported.
- End -
Associate POS Terminals with Cameras
Using the Associations section in the POS Terminal editor, you can associate one or more cameras with the terminal.
These should be cameras whose field of view includes the physical terminal.
Procedure 27-3 Associate POS Terminals with Cameras
Step Action
1
Select Terminal from the Setup tab.
2
Select Show All from the dropdown.
3
Right Click the Terminal to edit.
4
Select Edit.
5
Expand the Associations section.
6
Select
7
Use the Object selector to select cameras to associate with the terminal.
8
Select OK.
9
Select Save.
. The Object selector displays.
- End -
169
Camera Region Editor
The Camera Region Editor allows you to define color coded overlays on camera views associated with terminals.
Four overlay types are available: Customer Present, Merchandise, Employee and Terminal.
Assigning regions to terminal cameras in a retail environment makes them easily identifiable when POS video is
retrieved for those terminals.
Note:
The Customer Present region can be aligned with the customer present analytic available on VideoEdge 4.4+
Regions can be assigned from the Camera region editor in the Build tab, or alternatively you can access the editor by
right clicking on a terminal on the device list and selecting Configure Regions.
To use the Region editor the camera must be associated with a terminal.
Procedure 27-4 Edit Camera Regions
Step Action
1
Select Camera Region Editor from the Build tab. The Editor displays.
2
Select click the terminal with which the camera view is associated. Camera icons display.
3
Select the Camera on which to draw the Region of interest (ROI). Camera view displays with drawing tools.
4
Select the region type to be drawn from:
• Customer Present (Analytic available)
• Merchandise (For information only)
• Employees (For information only)
• Terminal (For information only)
5
Use drawing tools to draw the required ROI.
6
Select Save or continue drawing / editing as required.
- End -
170
UnifiedPOS Transactions
Importing UnifiedPOS Transactions
UnifiedPOS Transaction Reports can be imported into victor allowing video data to be aligned with transaction data.
During import, the file is validated against the UnifiedPOS standard. If the file is not in UnifiedPOS XML format, the
import will fail.
During the import, victor examines each transaction and checks for corresponding stores and terminals in victor using
the RetailStoreID and WorkstationID properties. Any transactions that do not have a corresponding store and terminal
in the system are rejected. The rest will are stored in the victor database.
Procedure 27-5 Import POS Transactions
Step Action
1
Select Transactions from the Build tab.
2
Select ImportUnifiedPOS. Import File dialog displays.
3
Navigate to the file to import.
4
Select Open.
5
Enter Time Offset if required. This is the time between the POS terminal and victor.
6
Select OK. The file import begins. The file is validated first to ensure UnifiedPOS requirements are met.
Select More Detail to view progress and status of import.
Note:
Workstation ID, and Retail Store ID must align with the corresponding object properties in victor.
7
Select Close when import is complete.
- End -
171
POS Search and Retrieve
Using the POS Search and Retrieve wizard, you can search POS Transactions and view results alongside associated
video data. Transaction video displays in the POS surveillance window while the associated transaction data displays
in a separate pane.
Procedure 27-6 Search POS Transactions
Step Action
1
Select Search and Retrieve (POS) from the Home tab. Transaction Search Wizard displays.
2
Drag the required terminal or store into the terminal list area.
3
Specify the start and end time to be searched within.
4
Select checkbox if Customer Filtering is required, then select the filter:
• Include All Transactions - No Customer filtering.
• Include only transactions with no customers (Requires Customer present video Intelligence).
• Include only transactions with customers (Requires Customer present video Intelligence).
Note:
Customer Present Video Intelligence is a VideoEdge NVR 4.4+ licensed add-on. In order to use this
feature, a license must be purchased for each camera.
5
6
Apply UnifiedPOS search rules if required:
a
Select
Object selector displays.
b
Select the POS Search property from the object selector.
c
Select OK Search property displays in the wizard.
d
Apply And/Or and Operator Values as required.
e
Apply Value as requires - This field may be a dropdown selection or free text depending on the Search
property selected.
Select Finish. Search results (video and transaction data) display in the POS surveillance window.
- End -
172
POS Terminal View
You can view POS transactions related to specific terminal objects directly from the device list. This action opens a
transaction surveillance window displaying the cameras associated with that terminal.
Procedure 27-7 POS Terminal View
Step Action
1
Right click the required terminal on the device list
2
Select View. Transaction Viewer displays.
3
Use playback controls to navigate to the required time interval.
Note:
You can use the play controls to navigate forwards and backwards through the video. While paused,
you can drag in additional cameras or terminals that will be time synchronized with the others. As
transactions occur on one of the terminals in the POS Transaction Viewer, the text of that transaction
will be displayed in the text pane to the right of the video. The text will remain in this pane until it is
replaced by another transaction.
If configured, overlays are displayed in this view displaying camera regions defined for merchandise, Customer
present, Employee or Terminal. Refer to Camera Region Editor.
- End -
POS Exceptions Reports
POS Exception Reports
In addition to raw POS transactions, victor can also import POS Exception Reports. A POS Exception Report
typically lists transactions deemed to be exceptional in some way.
Trying to align exception data with video data manually can be very time consuming and error prone. The victor POS
exception report feature automates much of this process.
Assuming the POS terminals are already configured (If not refer to Create POS Terminal Objects and Associate
POS Terminals with Cameras). You can then import POS exception reports and align video data with the
transactions.
POS Exception Reports come in many different formats from different vendors and are often customized by company
rules and procedures. Therefore, victor has a flexible template-based system that can understand many different
report types and formats.
173
POS Exception Report Requirements
At a minimum, POS exception reports must:
• Be in Row-Column Format
• Be either .csv or .xls file format
• Contain columns for Date, Time and POS Terminal ID of the transaction
• List exceptional transactions
Any other information the report may contain will be imported and displayed but is not required for the import.
Three types of rows are supported:
• Key row (one) - The first row of the report.This row names the columns in the report
• Terminal rows (one or more). Contain the transaction data
• Group rows (one or more). Used to link together terminal rows
Import POS Exception Reports
The POS Report Import wizard guides you through the several steps required to import a new report and also create a
report template. Templates are useful as the next time you import a report of that type, victor will recognize it and
import it directly.
Procedure 27-8 Import POS Exception Reports
Caution
Before importing POS data into victor you should remove or securely obscure any sensitive credit card information.
victor unified client has not been certified for PCI DSS compliance.
Step Action
1
Select Report from the Build tab.
2
Select Import Report. Exception Report Import Wizard displays.
3
Select Browse.
4
Navigate to and select the exception report.
5
Select Open. A Report Preview displays. Use the Report Type dropdown to select New or Existing. If it is a
new report type, the wizard will guide you through the rest of the process, if you select an existing report type,
the wizard will bypass report configuration and prompt for import.
6
Select Next. Exception Report Header screen displays. Set the report header by selecting the row
containing the required column headers. After selecting the header row, you can change the column header
names by selecting the name in the preview area and entering a new name.
7
Select Next. Mandatory Columns screen displays. Drag column headers from the preview datagrid into the
relevant column dropboxes.
8
Select Next. Additional Info screen displays. If your exception report groups exceptions underneath header
rows, select a header row from the preview datagrid and then select a property header from the property table.
9
Select Next. Save Report Template screen displays:
• Enter New Report Name (Select Save when entered) - The new template will save
with this name.
174
• Select Enable Customer Filtering if required. This means you can filter POS Exception Reports based on whether a customer was present at the time of the exception or
not.
Note:
Customer Present Video Intelligence is a VideoEdge NVR 4.4+ licensed add-on. In order to use this
feature, a license must be purchased for each camera.
• Enter a Time offset if required
10
Select Next. Import Summary Screen displays. Review the report summary and use Previous and Next
Buttons to make any amendments as required.
11
Select Finish.
The report can be accessed from Build Tab > Exception Reports > Show All. Right click the report and select
View, Send To or Delete as required.
- End -
175
Generic Edge Devices and Reports
Introduction
You can import Generic Exception Reports which can be associated with either cameras or Generic Devices within
victor to associate video data with report data.
Generic Edge Devices must be configured within the client before reports can be created to associate victor video with
report data.
Generic Edge Devices
These devices are hardware objects which are added to victor for reference only. They enable you to associate
cameras so that when generic exception reports are run, you can view video aligned with report data.
victor does not poll these devices for status, the only meaningful reference which links the device to reports is the
External Identifier which maps to the report.
Associated camera views can be accessed by right clicking on the objects in the device list and selecting View.
Generic Exception Report Requirements
At a minimum, exception reports must:
• Be in Row-Column Format
• Be either .csv, .txt, .xls or .xlsx file format
• Contain columns for Date, Time and Generic Edge Device
• List exceptional transactions
Any other information the report may contain will be imported and displayed but is not required for the import to be
successful.
Three types of rows are supported:
• Key row (one) - The first row of the report. This row names the columns in the report
• Terminal rows (one or more). Contain the transaction data
• Group rows (one or more). Used to link together terminal rows
176
Import Generic Exception Reports
The Generic Exception Report wizard guides you through the several steps required to import a new exception report
and also create report templates. Templates are useful as the next time you import a report of that type, victor will
recognize it and import it directly.
Procedure 28-1 Import Generic Exception Reports
Step Action
1
Select Exception Reports from the Build tab.
2
Select Import Report. Exception Report Import Wizard displays.
3
Select Browse. Open dialog displays.
4
Navigate to and select the exception report.
5
Select Open. A Report Preview displays in the File Select screen.
6
Select Generic Edge Devices or Cameras from the Type dropdown.
7
Use the Report Type dropdown to select whether the report is new or uses an existing template. If New
Report Type is selected, the wizard will guide you through the rest of the process, if you select an existing
report type, the wizard will bypass report configuration and prompt for import.
8
Select Next. Exception Report Header screen displays. Set the report header by selecting the row
containing the required column headers. After selecting the header row, you can change the column header
names by selecting the name in the preview area and entering a new name.
9
Select Next. Mandatory Columns screen displays.
10
Drag column headers from the preview datagrid into the relevant column dropboxes.
11
Select Next. Save Format screen displays:
• Enter New Report Name (Select Save when entered) - The new template will save with
this name
• Enter an External Device Time Offset if required
Note:
This setting allows you to adjust for differences between the External device Clock and the Video
System Clock so report time data and Video data align.
12
Select Next. Import Summary Screen displays. Review the report summary and use Previous and Next
Buttons to make any amendments as required.
13
Select Finish.
The report can be accessed from Build Tab > Exception Reports > Show All. Right click the report and select
View, Send To or Delete as required.
- End -
177
Camera Region Editor
Introduction
The Camera Region Editor provides a means to visually identify areas within a camera view represented by:
• Customers
• Merchandise
• Employees
• Terminals
Making associations between camera defined regions and edge devices allows users to view pertinent regions of
camera views when triggers are initiated from the associated items.
Define Camera Regions
Camera regions can be assigned from the Camera region editor in the Build tab, alternatively, you can access the
editor by right clicking on a terminal on the device list and selecting Configure Regions.
Procedure 29-1
Edit Camera Regions
Step Action
1
Select Camera Region Editor from the Build tab. The Editor displays
2
Select the Camera on which to draw the Region of interest (ROI). Camera view displays with drawing tools.
3
Select the region type to be drawn from:
• Customer Present
• Merchandise
• Employees
4
Use drawing tools to draw the required ROI
5
Select Save or continue drawing / editing as required
- End -
178
Reports and Data Visualization
Introduction
The reporting function is used primarily to display Journal and Audit information on system objects and activity.
Various predefined report templates are available within the client or alternatively, you can use ‘Ad Hoc’ reports for
more customizable reports which allow search terms to be used.
The Data Visualizer feature allows users to display report data graphically using Charts, Timelines and Report Grids.
Journal Filter
The Journal Filter is used to regulate the amount of data being written to the database (journaled) by
blocking/unblocking specific alert types. The feature is accessed from System Values on the Setup tab.
The following message types cannot be blocked and will always be journaled:
• General Purpose Interface Activity
• Operator Login
• State Change
• System Activity
• System Error
The default setting is to record, meaning messages will be written to the database unless they are blocked in the
journal filter.
Note:
Motion Detection, Light Change and Motion Exception Alerts are blocked by default.
Report exceptions are controlled at Object and Type level. Object Exceptions override Type Exceptions - therefore if
an alert type is blocked at type level but allowed for a specific object, the object’s alert will be written to the database
but the block on the type remains valid.
179
Generate / Save Reports
Various predefined report templates are available within the report editor. These can be used to generate reports to
retrieve Journal and Audit information on system objects and activity. From the reporting dialog, reports can be saved
so they can be executed later.
Procedure 30-1 Generate / Save Reports
Step Action
1
Select Reports and Data Visualization from the Home tab.
2
Select New from the dropdown. Reports Editor displays.
3
Select the required date range using the Date Range Picker.
4
If required, select a report Category from the dropdown.
5
Select a report Template from the dropdown.
Note:
1. Available templates may vary depending on which integrations are installed.
2. On selection each template populates the fields below the drop down with relevant filters
(appropriate to report type).
6
Select
and use the Object Selector to apply filters as required.
7
Select New Tab checkbox to open results in a new tab (optional).
8
Select from the following:
• Execute to run the report
• Visualize to send report results to Data Visualizer
• Save to save the report for future use (new dialog displays)
Note:
The Save dialog allows the user to provide a Name and Description for the report. It also allows the
user to specify whether the report should prompt for new/different filters when it is executed. If
checked when the report is executed the standard report dialog will be presented with the saved
report information loaded. If the user configures a report with “Custom” as the Date Range, the report
will prompt on execution so the user can specify dates.
• Exit to exit without saving.
- End -
180
Ad Hoc Reports
The Ad Hoc tab contains journal message types that do not have associated report templates. The control that is
shown for these types of reports allow you to pick an object, type or to enter a name to filter by.
Procedure 30-2 Generate/Save Ad Hoc Reports
Step Action
1
Select Reports and Data Visualizer from the Home tab.
2
Select New from the dropdown. Report Editor displays.
3
Select the required date range using the Date Range picker.
4
Select the Ad Hoc tab.
5
Select the Event Type from the dropdown menu.
6
Use the Object Selector or the Name textbox to enter a search term.
7
Select New Tab checkbox to open results in a new tab (optional).
8
Select from the following:
• Execute to run the report
• Visualize to send report results to Data Visualizer
• Save to save the report for future use (New dialog displays)
Note:
The Save dialog allows the user to provide a Name and Description for the report. It also allows the
user to specify whether the report should prompt for new/different filters when it is executed. If
checked when the report is executed the standard report dialog will be presented with the saved
report information loaded. If the user configures a report with “Custom” as the Date Range, the report
will prompt on execution so the user can specify dates.
• Exit to exit without saving
- End -
Show All
You can view an object list of all saved/available reports by selecting Reports on the Home tab and Show All.
The saved reports are shown in a dynamic view and are by default grouped by Report Template type.
Right Clicking on any report offers the following options:
• Edit: Modify the filters for the report.
• Delete: Deletes the saved report.
• Execute: Displays a dynamic view with the results of the report.
• Visualize: Displays a data visualization control with the results of the report.
181
Find in Journal
The Find in Journal feature allows you to search for journal records relating to specific objects of interest.
If the Find in Journal feature is available for an object, it is typically accessible from the object's context menu.
Procedure 30-3 Find in Journal
Step Action
1
Right click the required object.
2
Select Find in Journal. Report Selection dialog displays.
3
Select the required Report Type from the dropdown.
4
Select the date range using the From and To date controls.
Note:
The Search Name will be populated by the name of the object selected. If required, enter the
Operator Name.
5
Select OK. Reports displays.
- End -
Log General Message
You can write a manual entry to the journal using the Log General Message feature.
As well as entering a manual message, you can select and edit any of the predefined messages which may be
available.
General messages are available as a report type.
Procedure 30-4 Log General Message
Step Action
1
Select Log General Message from the Home tab. Log Message(s) dialog displays.
2
To enter a manual message:
3
182
a
Enter a message as required.
b
Select
c
Select OK. Selected messages are journaled.
to enter additional messages. Select
to remove messages.
To enter a predefined message:
a
Select Select Message from Predefined Message log dropdown.
b
Select Predefined Message.
c
Select
d
Select OK. Selected messages are journaled.
to enter additional messages. Select
to remove messages.
- End -
Predefined Messages
Predefined Log Messages can be created which can then be used when required to acknowledge or clear an event
without needing to type text.
Messages are identifiable by their labels which are assigned when they are created.
Labels and message fields are mandatory for every message created. Labels can be up to 100 characters in length
and messages up to 3000.
The language for each message can also be assigned, this means when a user logs a message, the messages
available are filtered to provide current language messages only. To log a message in a different language, you must
switch language in the client.
Procedure 30-5 Create a Predefined Log Message
Step Action
1
Select Predefined Message Log from the Build tab.
2
Select New from the dropdown menu. New Predefined Message editor displays.
3
Select the Language dropdown.
4
Select the language in which the message is to be displayed.
5
Double click the Label textbox.
6
Enter Label text as required. Double click the Message textbox.
7
Enter message text as required.
8
Select
9
Select Save.
to add additional messages or
to remove selected messages.
- End -
183
Data Visualization
Data Visualizer can be used use to graphically chart most event data available in victor. The charts can be used to
visualize the data over time, and to compare different events as different data series.
A typical use case for data visualizer could be for People or Object counting. This could be achieved by using Data
visualizer combined with the VideoEdge Video Intelligence software add-on to form a useful People Counting solution.
Note:
The Video Intelligence software is a licensed add-on to the VideoEdge NVR product. You must obtain a license for
each camera before the video intelligence features are available.
Report Results
Once search parameters have been entered into the Reports or Ad Hoc tab (see Generate / Save Reports and Ad
Hoc Reports), select Visualize. Report results will display in the Data Visualizer.
Search & Retrieve Results
Once a Search & Retrieve has been run, select
to view results in the Data Visualizer.
Using the Data Visualizer
Once data has been populated in the Data Visualizer, it can be further manipulated.
‘Drill Down’
When results have been populated in the Data Visualizer, the X axis will display time relevant to search criteria and
the Y axis will display the number of occurrences. In the example shown below, the search was carried out over a 3
day period, with each column representing 1 day:
184
From this view, you can further ‘drill down’ into a time period by double clicking a column. For example, double clicking
on the ‘Apr 08’ column will ‘drill down’ into that day, displaying columns for each hour, as shown below:
You can continue to ‘drill down’ into more narrow timeframes until the Drill Down Threshold of occurrences has been
reached. The Drill Down Threshold is set from the Customize tab of the Data Visualizer and is the limit of number
of occurrences that you can drill down to. Once the Drill Down Threshold has been reached, double clicking a
column will open a surveillance pane displaying results. If no video is associated, drilling down will return a view of the
type.
Customize Tab
Buttons available on the Customize tab are outlined below:
Fit Horizontal & Vertical - fits chart horizontally and vertically
Fit Horizontal - fits chart horizontally
Fit Vertical - fits chart vertically
Toggle Crosshairs - toggles crosshairs on chart on and off
Toggle Gridlines - toggles gridlines on chart on and off
Export to File - exports current data visualizer view as a .jpg file
Export to Excel - exports current data visualizer view and data in Microsoft Excel format (.xlsx)
Export to XPS - exports data as a .xps file
The Series section of the Customize tab enables customizing of the color of all series displayed in the data
visualizer, along with the ability to add a Mean line or Trendline to the chart.
185
The Customize section of the Customize tab enables changing of axis settings to Log Axis and Show Zeros, along
with changing the series Type (Line, Column, Bar, Area), which Trendline (Linear, Logarithmic, Quadratic, Cubic) is
displayed and setting of the Drill Down Threshold.
Filter Tab
The Filter tab allows for filtering of the chart by Object Type, Object Name or Alarm. Select required option then
select Update Chart to apply.
Report Search
Selecting the Report Search tab opens the report search interface from which reports and ad hoc reports can be run.
Refer to Generate / Save Reports for more information.
186
Roles
Introduction
A Role is a set of access rules which is assigned to an operator to govern their authorization and permission levels
within victor. Effective role management enables complete control over the resources and features users can access.
Be careful of the roles you give users on your system. If you add a user as an administrator, you are granting them full
system permissions.
Note:
Before deleting roles, ensure they are not assigned to operators
Role Types
Canned Roles
There are five predefined (canned) roles, ready for assignment to users. Each of these roles, apart from Administrator
can be edited to refine them further. Canned roles are as follows (Descending permission level):
• Administrator
• Power User
• Investigator
• Guard
• Viewer
Custom Roles
As well as using canned roles, you can create custom roles. This can be done using the ‘Save As’ feature which
allows a current role to be used as a template to build a new role, or you can build a completely new role manually.
Each new role created is available for selection when creating or editing operator profiles.
Type/Object Exceptions
The level of permissions assigned to a role is controlled by exceptions. When a custom role is initially created, full
administrative access is granted by default, the role can then be edited to add type and object exceptions to restrict
access to resources and features.
It is important to understand the difference between Type and Object Type exceptions. Type relates to general groups
of objects E.G Recorders, Events while Object Exceptions relate to specific objects E.G Recorder ‘X’ or Event ‘Y’.
187
Create Roles
If a canned role does not meet your requirements, you can create new customized roles.
Procedure 31-1 Create a Role
Step Action
1
Select Role from the Build tab.
2
Select New from the dropdown menu. Role editor displays.
3
Enter a name for the role in the Name textbox.
4
Enter a description for the role in the Description textbox.
Note:
The Enabled checkbox is selected by default, deselect to disable the role.
5
6
To assign Type Exceptions:
a
Expand the Type Exceptions section.
b
Select
c
Select the Object Type as required.
d
Select OK. Exception ‘Allow’ list displays.
e
Select the Allow checkbox next to permitted actions, deselect for non-permitted actions.
f
Repeat as required.
g
Use
. Type Selector dialog displays.
to remove selected type exceptions.
To assign Object Exceptions:
a
Expand the Object Exceptions section.
b
Select
c
Use the Object selector dialog to select the object as required.
d
Select OK. Exception ‘Allow’ list displays.
e
Select the Allow checkbox next to permitted actions, deselect for non-permitted actions.
f
Repeat as required.
g
Use
. Object Selector dialog displays.
to remove selected object exceptions.
7
Expand the Layout section.
8
Use the Object Selector to assign a layout as required.
9
Select Save.
- End -
188
Copy Roles
Existing roles can be used as templates to create new roles which can then be edited. This is useful if you need to
create a role which is similar to but not identical to an existing role.
Procedure 31-2 Copy a Role
Step Action
1
Select Role from the Build tab.
2
Select Show all from the dropdown menu.
3
Right click the role to be copied
4
Select Save As. Really save a copy of the specified object? dialog displays.
5
Select Yes. A copy of the role is created and displays on the object list. The copied role is identifiable as it
has the original role name appended with ‘_Copy’.
6
Right click the new role.
7
Select Edit.
8
Use the Type and Object selectors as required to edit the role.
9
Select Save.
- End -
189
Sites
Introduction
A Site is a user definable list of folders into which you can drag devices and objects.
Sites allows users to organize and group objects into logical folder views instead of the traditional device driven views.
Users can create sites and folders with custom names and organize the objects within according to criteria relevant to
that site.
For example, a folder can be named ‘East Car Park’ and that folder can be used to group objects related to that
particular area (Cameras, Recorders etc.)
The site list is therefore used as a convenient method from where to open objects and views related to a particular
physical location.
Create a Site
You can add new sites to victor which allow you to group and manage devices within a specific area.
Procedure 32-1 Create a Site
Step Action
1
Select Sites from the Home tab. Site window displays.
2
Right Click in the white space within the sites window.
3
Select Add Site. A new folder is created called New Site.
4
To rename the folder:
a
Right click the folder
b
Select Rename Site
c
Enter Site Name
d
Select OK.
Note:
Site list reorders alphabetically as new sites are added, deleted or renamed.
5
6
To Add Objects:
a
Select the object to be added
b
Drag and Drop into the required site folder
c
Repeat as required
To Remove Objects:
a
Right click the object to be removed
b
Select Remove from the list.
190
Note:
Delete option is also available in this context menu. Selecting Delete removes the object
permanently.
- End -
191
General Purpose Interface
Introduction
The General Purpose Interface (GPI) is a programmable bi-directional communication protocol which enables victor to
interact with third party devices.
To achieve this, the General Purpose Interface:
• Initializes communication between victor client and a third party device.
• Maintains a communications channel by polling the third party device.
• Defines General Purpose Actions which send messages to third party devices using victor event activation
and supports acknowledgment messages from third party devices.
• Defines General Purpose Monitoring Points which represent monitoring points in third party devices.
• Defines General Purpose incoming message protocols which interpret incoming messages from third party
devices and support acknowledgment for incoming messages.
Terminology
GPI
General Purpose Interface
Device
The central third party hardware device
Monitoring Point
victor data type which changes state based on
incoming messages from the device
Protocol
Action Messages
Sent to the device as a result of events triggered in
victor
Actions
Objects created in victor which are transmitted to
the General Purpose Device based on activated
events in victor
Input
Where the input strings are sent from the device
through the Serial/Network port to victor
Output
Where the output is an action and requests a
response from the device
Poll
Where the poll is an action which requires a
response from the device
STX
Start of Text
ETX
End of Text
192
The General Purpose Interface can work with any device which uses ASCII code communications protocol for event
monitoring, such as:
Intercom
Process Control Equipment
Burglar/Intrusion
Environmental
Dome Control
Lighting
Access Control
Refrigeration
Elevators
Wireless Communication
The third party device sends pure ASCII messages via a serial port (RS-232) or remotely via a TCP/IP port (Lantronix
or Systech) to the General Purpose Interface Driver.
This means that you can respond to alarms from many types of third party devices as well as the system video and
health alarms described in ‘Events’.
The General Purpose interface supports the following functionality:
• Input - Where the input strings are sent from the device through the Serial/Network port to victor
• Output - Where the output is an action and requests a response from the device
• Poll - Where the poll is an action which requires a response from the device
193
Monitoring Points
Monitoring Points are victor data types which change state based on incoming messages from the device. Monitoring
Points can be configured to directly trigger Events.
Events can be designed to activate any victor event action.
You can configure a message protocol which then parses the received Monitoring Point string. You can also define
header and trailer characters in the Protocol area of the General Purpose Interface.
Monitoring Points can also be annunciated at the monitoring station and written to the historical journal.
Monitoring Point Message Processing
When the General Purpose Driver receives the message from the device, it does the following:
1
Parses the message and looks for poll or action responses
• If it finds a poll or action response, it processes the response
• If it does NOT find a poll or action response, it continues to parse
2
Looks for a message protocol
• If it finds a message protocol, it processes the protocol
• If it does NOT find a message protocol, it continues to parse
Note:
The device can delimit the message with or without header and trailer characters
Poll Command
The Poll Command, frequency of polling and expected response (Poll Command Acknowledgment) are all defined as
part of the configuration of a specific General Purpose Device.
Poll Command Acknowledgment
Some protocols will include an acknowledge character returned to the device that issued the polling command - this is
additional confirmation that the general purpose device received the command.
Output
Output is performed using an Action which is activated by an Event. The output sends a string of characters to the
General Purpose Device through the serial/network port.
The optional expected response is also configured as part of the action.
194
Virtual Keyboard
As the ASCII characters between 0 and 32 are not visible on screen and have no equivalent keyboard button, the
virtual keyboard is relied on to enter these values. Some common values are the STX (Start of Text) and ETX (End of
Text) which have no keyboard button but can be entered via the virtual keyboard.
When configuring some General Purpose Interface components, you will be required to use a Virtual Keyboard as not
all characters are available on a standard keyboard. The keyboard displays on screen when
is selected.
The virtual keyboard is required when entering text into:
• General Purpose Device Editor - Device Information section to enter the Poll Command/Poll Command Acknowledgment
• General Purpose Protocol Editor - Protocols section to enter keywords
• General Purpose Action Message Editor - Action Message section to enter Outgoing and Acknowledgment messages
• General Purpose Monitoring Point Editor - Messages section to enter Acknowledgment message
195
Procedure 33-1 Entering Text Using the Virtual Keyboard
Step Action
1
Navigate to the field where text is to be entered.
2
Select
3
Select characters as required. Characters display in the text field.
. Virtual Keyboard is displayed.
Note:
ASCII table can be viewed by selecting ASCII Table
4
Select Save.
- End -
Create New Device
Third Party Devices can be created and configured within the client.
196
Field
Description
Name
Enter a unique name to identify the General
Purpose Device.
Description
Enter a description of the General Purpose Device.
Enabled
Select checkbox to enable the General Purpose
Device.
Vendor
Click to select the name of the manufacturer of the
General Purpose Device.
Poll Period (seconds)
Enter the period in seconds during which victor
attempts to poll this General Purpose Device. The
default value is 10 seconds.
Enter the poll command (command string) that
victor sends to the General Purpose Device.
Poll Command
,
allowing creation and editing of text strings.
Open the virtual keyboard by selecting
Poll Command Acknowledgment
Enter a poll command acknowledgment (the
command string) that the General Purpose Device
sends back to victor as acknowledgment of the poll
message.
,
allowing creation and editing of text strings.
Open the virtual keyboard by selecting
Journal Unknown Message
Select this option to record unknown messages
received by victor in the historical journal
Serial Port
Select Serial Port if you are using a serial
connection. This is the default port type.
Network Port
Select Network Port if you are using a terminal
server for the connection.
Enter the TCP/IP address of the network port
IP Address
Communication Port
Note:
This option is only available if you select
the Network Port option.
Enter the port number:
• Serial Port - enter a port number such as COM1,
COM2, etc.
• Network Port - enter the TCP/IP port number
which the terminal uses to communicate with
victor
Enter the duration in seconds before trying to
reconnect to an unresponsive network device.
Reconnection Period (secs)
TimeOut Delay Time (1/10 secs)
197
Note:
This field is only available if you select the
Network Port option
Enter the extra interval (in 1/10 seconds) that victor
waits for a response from the device after sending
a message to the switcher.
If a response is not received in time, the message
is retransmitted or communications failure
declared.
Default value is 20 (2 seconds).
Comm Fail Delay Time (secs)
Enter the time period (in seconds) after the
TimeOut Delay Time expires that victor waits to
declare an unresponsive device as failure.
Default value is 300 seconds.
Header Character
Enter a value (in decimal) to define the first
character in a message from the General Purpose
Device. Zero (0) indicates that any character can
be the first character.
Default value is zero (0)
Enter a value (in decimal) to define the last
character from the General Purpose Device.
Default value is 13.
Trailer Character
Note:
1. The value cannot be zero (0).
2. A Trailer Character is mandatory.
Message Resend Count
Enter the number of times victor should attempt to
resend a message that the device has not
acknowledged receiving.
Default value is zero (0).
Max Buffer Size
Enter the maximum size of the buffer that stores the
message from the device.
Default value is 2000.
198
Procedure 33-2 Create New Device
Step Action
1
Select Device from the Setup tab.
2
Select New. General Purpose Device editor displays.
3
Enter a name for the device in the Name textbox.
4
Enter a description for the device in the Description textbox.
5
The Enabled checkbox is selected by default. To disable the device, deselect the checkbox.
6
Select the vendor from the Vendor drop down menu.
7
Enter Poll Period.
Note:
1. When configuring a non-zero Polling Period, non-zero values should be set for TimeOut Delay
and Comm Fail Delay times.
2. When configuring a zero Polling Period, zero should also be set for TimeOut Delay and Comm
Fail Delay times.
8
Enter the poll command in the Poll Command textbox. This is a stream of bytes, usually set by the device
manufacturer, sent on a regular basis to the device to maintain communications.
9
Enter Poll Command Acknowledge. This is the expected response from the device which is sent back to
victor as acknowledgment of the poll message.
10
The Journal Unknown Message checkbox is deselected by default. To enable, select the checkbox.
Note:
Enabling Journal Unknown Message means that any message received by the victor General
Purpose server component that does not match an existing protocol will be sent to the activity
viewer. When disabled, unknown messages are ignored.
11
Select either Serial Port or Network Port.
• If Serial Port is selected:
a
Enter Communication Port.
• If Network Port is selected:
a
Enter IP Address.
b
Enter Communication Port.
c
Enter Reconnection Period.
12
Enter TimeOut Delay Time in 1/10th seconds.
13
Enter Comm Fail Delay time.
14
Enter Header Character.
15
Enter Trailer Character.
Note:
Trailer Character is mandatory.
16
Enter Message Resend Count.
17
Enter Max Buffer Size.
199
18
Select Property from the drop down menu.
19
Select Value from the drop down menu.
20
Select
21
Select Save.
then select an Action from the Object Selector.
- End -
Create New Monitoring Point
New monitoring points can be created and configured from the General Purpose Interface.
Each monitoring point supports up to five activated status properties which are assigned during configuration.
Activation and deactivation messages associated with each monitoring point are drawn from the message protocol
pool.
State changes occur depending on the interpreted incoming messages of the General Purpose Device. State changes
are recorded in the journal logs and can trigger other actions in victor.
Field
Description
Name
Enter a unique name for the monitoring point.
Description
Enter a description of the monitoring point.
Enabled
Select to enable the monitoring point.
General Purpose Device
Select the General Purpose Device to be
monitored.
Acknowledgment Message
Enter a message string that victor sends to the
General Purpose Device as an acknowledgment
message.
Journal Message
(1-5)
Enter a meaningful word to identify the message
logged in the historical journal by this device.
Activation Message
(1-5)
Select
and use the Object Selector to select a
General Purpose Incoming Message Protocol to
trigger this monitoring point to activate.
Deactivation Message
(1-5)
Select
and use the Object Selector to select a
General Purpose Incoming Message Protocol to
trigger this monitoring point to deactivate.
Procedure 33-3 Create New Monitoring Point
Step Action
1
Select Monitoring Point from the Setup tab.
2
Select New. Monitoring Point Device editor displays.
3
Enter a name for the monitoring point in the Name textbox.
4
Enter a description for the monitoring point in the Description textbox.
200
5
The Enabled checkbox is selected by default. To disable the device, deselect the checkbox.
6
In the Device section, select
7
Enter Acknowledgment Message.
8
Enter a meaningful word or phrase in the Journal Message 1 textbox.
9
Select
and use the Object Selector to select an Activation Message.
10
Select
and use the Object Selector to select a Deactivation Message.
11
Repeat steps 8-10 to add more journal, activation and deactivation messages, up to a maximum of 5.
12
Expand the Alerts section.
13
Select
14
Select Property from the drop down menu.
15
Select Value from the drop down menu.
16
Select
17
Select Save.
and use the Object Selector to select the required device.
to add an alert.
then select an Action from the Object Selector.
- End -
201
Add New Protocol
New general purpose protocols can be created and configured from the General Purpose Interface. This is the
language used to communicate with the device.
Protocols are established via a dynamic process which combines match criteria, keywords and character positioning.
Individual message protocols then get combined with monitoring points to identify state changes in the General
Purpose Device.
Optionally, acknowledgment messages can be associated and transmitted with the monitoring point.
Field
Description
Match Criteria
(1-5)
Select match criteria for the keyword:
Include - the system will expect the keyword to be
included in a message from the General Purpose
Device
Exclude - the system will not expect the keyword to
be included in a message from the General
Purpose Device
Enter a keyword (max 50 characters) from this
message protocol.
Keyword
(1-5)
Note:
ASCII Hex 00 (Zero Zero) cannot be used
in a keyword
Enter a position for the keyword:
Value >0 (Zero) - the software device receiver
searches for the keyword only at this position when
mapping a message
Value =0 (Zero) - the keyword can be at any
position in the message (default)
Position
(1-5)
Example: To find “CDE” in the string “ABCDE”, the
Keyword value should be “CDE” and the Position
value, “3”
Note:
Spaces and unprintable characters such
as carriage returns (<CR>) or line feeds
(<LF>) must be counted
Procedure 33-4 Add New Protocol
Step Action
1
Select Protocol from the Setup tab.
2
Select New. General Purpose Protocol editor displays.
3
Enter a name for the protocol in the Name textbox.
4
Enter a description for the protocol in the Description textbox.
5
Select Match Criteria from the drop down menu.
6
Enter a Keyword.
202
7
Enter the Position.
8
Repeat steps 5-7 to add more protocols, up to a maximum of 5.
9
Select Save.
- End -
Create New Action Message
New action messages can be created and configured from the General Purpose Interface. Action messages are sent
to the device as a result of events triggered in victor.
Field
Description
Name
Enter a unique name for the action message
Description
Enter a description for the action message
Outgoing Message
Define a message for victor to send to the General
Purpose Device
Acknowledgment Message
Define the message sent by the General Purpose
Device as acknowledged that the outgoing
message was received
Procedure 33-5 Create New Action Message
Step Action
1
Select Action Message from the Setup tab.
2
Select New. Action Message editor displays.
3
Enter a name for the action message in the Name textbox.
4
Enter a description for the action message in the Description textbox.
5
Enter outgoing message text in the Outgoing Message textbox.
6
Enter acknowledgment message text in the Acknowledgment Message textbox.
7
Select Save.
- End -
203
Create a new General Purpose Action
New actions can be created and configured from the General Purpose Interface. Actions created in victor are
transmitted to the General Purpose Device based on activated events in victor. Actions can be associated with
acknowledgment messages.
Field
Description
Name
Enter a unique name to identify the General
Purpose Action
Description
Enter a description of the General Purpose Action
General Purpose Device
Select
and use the Object Selector to select the
General Purpose Device being monitored
General Purpose Action Message
Select
and use the Object Selector to select the
General Purpose Action Message that this action
triggers
Procedure 33-6 Create a new General Purpose Action
Step Action
1
Select Action from the Setup tab.
2
Select New. General Purpose Action editor displays.
3
Enter a name for the action in the Name textbox.
4
Enter a description for the action in the Description textbox.
5
Select
next to General Purpose Device and use the Object Selector to select the device being
monitored.
6
Select
next to General Purpose Action Message and use the Object Selector to select the action
message that this action triggers.
7
Select Save.
- End -
204
Health Monitoring
Introduction
victor Health Dashboard displays the health status of all configured victor devices.
The dashboard uses color coding to indicate the health status of devices:
• Green - Normal
• Yellow - At Risk
• Orange - Pre-Failure (Also applies to failover VideoEdge NVRs not currently in use)
• Red - Device Alert
• Gray - Unknown State
Note:
Intellex and ADHDVR recorders that do not use all analog ports display as red (Device Alert). If you prefer the
recorders showed up as gray (unknown Alert) as opposed to red you can disable offline cameras via the victor camera
editor.
The Health Dashboard supports the following items:
System Shutdown/Restart (VE)
No Volume (Intellex)
Unhealthy Disk (Intellex)
IP Address
Volume Missing (VE)
Disk Temperature (Intellex)
Software Version
RAID Degradation (VE)
Video Loss
Online/Offline
Failover (VE)
Number of Hard Drives
Disk Full (HDVR)
Number of Cameras
Overheating (HDVR)
Status of Cameras
Volume Failed (Intellex)
205
Using the Health Dashboard
The Health Dashboard can be launched from the Home tab:
The Health Dashboard will open displaying 2 panes: the device/site list pane and the device information pane.
Various controls and filters are available to limit or expand device information by type, severity or device quantity per
page. You can also expand/collapse device information and use pagination controls to scroll dashboard pages.
206
Device/Site List Pane
The Device/Site List Pane displays all health dashboard supported devices and sites, along with an indication of their
health status. Devices which will display in the health dashboard are:
Recorders
Intellex
VideoEdge NVR
HDVR
ADTVR
Controllers
iStar
apC
ISC
Intrusion Devices
DSC PowerSeries Panels
Bosch Receivers
Sur-Gard Receivers
Fire Devices
Simplex 4100U Panels
MZX Panels
Doors
iStar
apC
ISC
Elevators
Kone
Otis
Thyssen Krupp
Health status is indicated by highlighting at Object Type Level. Users can then navigate through the Device or Site
List to display health status information for all devices. Double clicking a device in the Device/Site List Pane will
display more detailed information in the Device Information Pane.
207
Device Information Pane
The Device Information Pane displays more detailed information of configured victor devices, including those selected
from the Device/Site List Pane.
In addition, the Device Information Pane can also be used to navigate health status information of devices. For
example, double clicking a recorder will open an interface like the one shown below:
This interface displays detailed device information as well as the health status of the device. To view all configured
objects of a certain type, use the device category buttons.
Health Mode in Maps
Health status information can be viewed on Maps. For more information, refer to Viewing Maps.
208
Unification/Integration
Introduction
C·CURE Unification
You can manage C·CURE 9000 access control events through victor. Lock and unlock doors, check status of access
control devices, and acknowledge events and alarms. In addition, you can arm and disarm inputs and deactivate and
pulse outputs. You can see the status of all controllers and other access control devices both from the device list and
through maps. Events can be acknowledged in either C·CURE 9000 client or the victor client as required and update
real-time. C·CURE 9000 alarms display on victor maps, event viewer and in reports/activity list.
Note:
victor and C·CURE integration requires the following versions:
victor version v4.2+
C·CURE 9000 v2.1+
For detailed installation instructions, refer to the victor/C·CURE unification manual.
Third Party Integrations
As well as C·CURE 9000, victor also extends Event Management support to various third party fire and intrusion
integrations. For a full list of drivers, refer to the American Dynamics website (www.americandynamics.net):
Integration with third party add-ons enables victor’s device list to display C·CURE and Third party hardware. All
objects support the victor privilege configuration and authorization.
All actions and state changes related to integrated objects are written to victor’s journal database and display on the
activity list. victor’s reports also support Access Control, Fire and Security modifications.
Alarms from integrated objects can be used to trigger victor Events.
Refer to the relevant victor integration manual for detailed information on integration, installation and operation
instructions.
209
Appendix A: victor MAS/SAS Support
Introduction
To enhance scalability and deployment in enterprise environments, victor unification with C·CURE allows you to
configure a site that is part of a 'hub-and-spokes' topology, but also has the ability to function in a disconnected
environment with complete local command and control.
Each Master Application Server (MAS) and up to 20 Satellite Application Servers (SAS) can be deployed as a single
system. The satellite servers provide real time response for critical operations like events and actions while the
master server provides a rolled up monitoring and reporting interface.
Each SAS contains database records for the system hardware connected to it, as well as other data relating to user
authentication and authorization. Each SAS synchronizes with the MAS so that SAS local data is replicated to the
MAS for central management and monitoring.
Data Types
Data Types
Global: Data which is configured on MASs and synchronized to all SASs.
Local: Data which is configured on and exists only on SASs.
210
Installation
The following enterprise deployments are supported:
• Installing victor locally on a C·CURE SAS or remotely connecting to a C·CURE SAS
• Installing C∙CURE on an existing victor Application Server and making it a SAS in an existing Enterprise
environment
• Installing victor on a MAS
Note:
Installing victor without C·CURE is not supported in SAS/MAS deployments
MAS Installation
Unified Server MAS can be installed by running the Tyco Security Products unified installer. The standard unified
server installer lays down all prerequisites required for MAS/SAS installation.
Caution
Refer to product datasheets for information on system hardware and software requirements
MAS Installation prerequisites
Prerequisites
The system where the MAS software will be installed must be a dedicated system on a domain. The system
should not host any other major applications
Ensure clocks are synchronized between the MAS and the SASs
The Windows domain user account of the MAS installer must be a system administrator for the system where the
MAS will be installed. (The account you install under must be a domain account, not a local computer account.)
The Windows user account of the MAS installer must have been configured as a SQL Administrator (sysadmin
role)
The SQL Browser Service must be enabled and running
You must have or obtain a MAS software license with the Application Server option enabled
Note:
Grant Administrative privileges to your Domain account on the new MAS.
Step Action
1
Follow the standard installation instructions provided on the unified server Installation guide until the Installation Type dialog displays.
2
At the Installation Type dialog, select Advanced (for Enterprise users) and select Next. Destination folder
displays.
3
Select Next.
4
Select Application Server Installation. Further options display.
5
Select Install as a Master Application Server.
211
6
Select Next.
7
Enter the database server name.Database server and Login Credentials dialog displays.
8
Select the local SQL server required for the installation (previously installed) as the Database Server and
select Next. The Remote Access Credentials dialog displays.
9
Enter Domain Username and Password as required.
Note:
Use a Domain Account\Username whose password will not be automatically updated as this will
adversely affect future connectivity. If your Windows password should change, you will need to
update the password used by the unified Windows services.
10
Select Next. The Ready to Install dialog displays listing the installation directory and the system server
type.
11
Select Install.
Note:
1. The Installing displays detailing status messages and progress (This process can take a
considerable amount of time)
2. If the installation completes without errors, the InstallShield Wizard Completed dialog box opens
3. If you received any warnings during the installation, the system displays a dialog box listing the
number of warnings. You can view these warnings in the %TEMP% directory.
12
Select Finish.
Note:
Once installation completes, you must register the product within sixty days from the date the
application was installed.
- End -
212
SAS Installation
Unified Server SAS can be installed by running the Tyco Security Products unified server installer. The standard
unified server installer lays down all prerequisites required for MAS/SAS installation.
SAS Installation prerequisites
Prerequisites
The system where the SAS software will be installed must be a dedicated system on a domain. The system should not
host any other major applications
Ensure clocks are synchronized between the MAS and the SASs
The Windows domain user account of the SAS installer must be a system administrator for the system where the SAS
will be installed.
The Windows user account of the SAS installer must have been provisioned as a SQL Administrator (sysadmin role)
on the MAS.
The Windows user account of the SAS installer must have been previously configured as a victor/C·CURE Global
Operator with the SYSTEM ALL Privilege at the MAS to which this SAS will connect.
The CrossFire Services must be configured to run using a domain user account on the SAS. That account must also
be a MAS operator able to access the MAS SQL database.
The SQL Browser Service must be enabled and running.
The MAS server that will be the master server for this SAS must be reachable via the network (its name or IP address
must be resolvable).
The MAS server that will be the master server for this SAS must be running as well as the Software House CrossFire
Framework and Component Framework Services.
Caution
Refer to product datasheets for information on system hardware and software requirements
Step Action
1
Follow the standard installation instructions provided on the unified server Installation guide until the Installation Type dialog displays.
2
At the Installation Type dialog, select Advanced (for Enterprise users) and select Next. Destination folder
displays.
3
Select Next.
4
Select Application Server Installation. Further options display.
5
Select Install as a Satellite Application Server and enter the Master Application Server name or IP
Address and select Next the Database server ddialog displays.
6
For the Database Server, select the required SAS database server name.
7
Select Next.
8
Enter your Domain\Username and your Password, confirm your password and click Next. The Ready to
Install the Program dialog box opens listing the location of the Installation directory, the Database server
type, and the system SQL server type.
213
9
Select Install.The Installing dialog displays.
Note:
1. The Installing displays detailing status messages and progress (This process can take a
considerable amount of time)
2. If the installation completes without errors, the InstallShield Wizard Completed dialog box opens
3. If you received any warnings during the installation, the system displays a dialog box listing the
number of warnings. You can view these warnings in the %TEMP% directory.
10
Select Finish.
Note:
Once installation completes, you must register the product within sixty days from the date the
application was installed.
- End -
214
Operation
MAS/SAS deployment affects how users interact with victor in various ways. Each of the following subsections
describes the enhanced user experience in affected areas as well as system capabilities and how they differ from a
non MAS/SAS environment.
Data Synchronization
victor specific data configured at the SAS in local partitions will synchronize up to the MAS. The victor Journal and
Audit will synchronize from the SAS to the MAS every four hours by default (this value can be changed in System
Values).
victor Application Server Interaction
General
On a MAS, the dynamic view of victor Application Servers lists all the SASs and the MAS the user has access to:
Interactive
From the dynamic view on the MAS you have the option to go interactive/non-interactive with a given SAS. This is
done via the right-click context menu.
When a victor Application Server is made interactive, it means that activity and events will be sent from the SAS up to
victor that is connected to the MAS (as if the client was directly connected to the SAS as its primary server).
You can configure whether each operator is be default interactive with any given victor Application server in the
Application Server section:
The items that are checked will be automatically interactive at startup when this operator logs in.
Sites
When a server is started, it will create a Site in the Site List with the same name as the victor Application Server. This
can be changed, but can’t be deleted. This means that every installation will have at least one Site present at all times.
215
Events
Events that are configured on the MAS are global. That means all events configured will be synchronized to all
interactive SASs.
The Event Viewer on the MAS is an event sink for all events from all SAS that are currently interactive.
If the source of an event activation belongs to an existing site, the site name will display in the Site field. If the source
does not belong to an existing site, the site that was created by the victor Application Server is displayed.
SAS Online: Normal event management (Acknowledge/Clear) workflows work the same as if directly connected to
the SAS.
SAS Offline: The event activation in the event viewer cannot be modified.
The operations that are performed on any event activation on the MAS or SAS is mirrored in real-time in both event
viewers.
The review operation available via the context menu will operate as normal on both the MAS and SAS.
Event Setup
Configure All:
Event Configurations of this type are synchronized to all SASs. This means that if the user configures All Doors ->
Forced -> Activate Global Event, every door in the Enterprise will activate this event when the door is forced.
Specific Objects:
These event configurations are saved on the SAS that owns the object being configured. So for a specific SAS door ->
Forced -> Activate Global Event, the configuration for this action will be saved at the SAS.
Note:
Event Setup editor on the MAS shows configurations for all objects in related SASs.
216
Maps
Maps can be created on both MASs and SASs.
MAS Maps: Maps created on MASs will not synchronize to SASs.
SAS Maps: Maps created on SASs, along with all their layers and objects are synchronized to the MAS and are
available to the MAS client.
Health Monitoring
Health monitoring at the MAS displays the health of all supported devices enterprise wide and if the SAS is interactive,
the states update accordingly.
The victor Application Server health status is included on the MAS dashboard as well as the status of all available
MAS and SAS machines.
Reports/Data Visualization
At the MAS client, reporting and data visulaization is available for data up to the last succesful synchronization of SAS
data up to the MAS.
Licensing
There are no additional license requirements to install victor on a SAS.
217