Preparation Guide

Preparation
Guide
Be prepared for anything
cleaners
fillers
adhesives
solvents
Introduction
At Manger’s, we want you to get it right first time, every time. And
that’s why we’ve been supplying you with excellent, value-for-money
decorating products since 1922. Our aim is to meet all of your
decorating needs with a credible and comprehensive selection of
product types in a choice of sizes. As part of the Johnstone’s and
Leyland family, we believe that good paint deserves a good surface
and with our help you can get a longer lasting, better looking finish
on all of your projects!
Be prepared for anything with this helpful Preparation Guide but if
you think of something we haven’t advised you on, please call
Customer Service on 01924 354354 for any queries regarding
Technical Advice or for General Support.
ready
mixed
expanding
sugar
soap
spray
mixes up to 22 litres
wipes away grease,
grime & nicotine
the original & the best
500ml ℮
foam
filler
mixes quickly to a smooth paste
suitable for any wallcovering
protects against mould
fills gaps of all
shapes & sizes
easily trimmed, sanded,
plastered or painted
strong, permanent filler
300ml ℮
2
filler
all purpose
wallpaper
adhesive
5 roll pack ℮
fungicidal
al
spray
ready to use
kills & removess mould & mildew
protects against
st regrowth
500ml ℮
ready to use
multi-surface interior
and exterior use
quick drying, smooth
and tough
330g ℮
Preparation Guide
Contents
Preparation
4
Papering
18
Preparing walls for paint
Treating problem stains
Remove, treat and prevent mould
Removing paint and varnish
Unblocking drains and pipes
Cleaning brushes
Cleaning paint from surfaces and hands
4
5
6
7
8
9
9
Tips for perfect papering
Hanging heavier wallpaper or in areas
prone to condensations
Sizing walls prior to papering
Mend wallpaper repairs
Hanging a border
18
20
Tiling
24
Applying wall tiles
Wall tile repairs
24
25
Manger’s Range
Overview
26
Decorating
Problems FAQs
28
Cleaning
10
Removing paint from soft furnishings
Cleaning glass surfaces
10
11
Cracks & gaps
12
Repairing interior surface cracks
Fixing intricate and fine repairs in walls
Repair ceiling cracks
Fill gaps in your kitchen or bathroom
Gaps between skirting boards and
joints subject to movements
Large, awkward and irregular gaps
Damaged exterior surfaces
12
13
14
14
15
21
22
23
16
17
3
Preparation
Preparing walls for paint
What you might not know is that our walls are hardly ever just right before
we decorate. Generally, they’re not chemically clean and are often covered
with small holes you don’t need.
Step A:
3
Use our ready-to-use Manger’s Sugar Soap Spray to leave the surface
chemically clean so that a fresh coat of paint adheres readily.
1: Shake the bottle
2: Always wear protective gloves and cover adjacent areas prior to use
3: Spray onto the surface to be cleaned
4: For very greasy marks or surfaces, leave for one minute
5: Rinse with clean water and allow to dry.
For heavily soiled areas, it’s recommended to use Manger’s Sugar Soap Concentrate or the
original Manger’s Sugar Soap powder (see Treating Problem Stains).
Step B:
sugar
soap
spray
mixes up to 22 litres
wipes away grease,
grime & nicotine
the original & the best
500ml ℮
4
Fill holes and minor cracks for a smoother finish. Manger’s Lightweight
Deep Gap Filler is a professional, quality filler specially formulated from
millions of tiny glass bubbles to fill most holes and gaps in one application.
It gives a super smooth, brilliant white finish, which does not need sanding.
It’s also very fast drying so you can start decorating in 15 minutes.
Preparation Guide
Step B: (cont)
1: Cover nail and screw heads with an oil-based primer, such as Leyland or
Johnstone’s All Purpose Primer, prior to application to prevent them rusting
3
2: Stir to a smooth paste, if product is too dry add a couple of drops of
water and re-stir
3: Apply directly into the gap, ensuring it is completely filled
4: Smooth the surface with a wet knife
5: Remove excess and allow to dry for at least 15 minutes.
Treating problem stains
Use our original, and highly effective, Manger’s Sugar Soap. Its powerful
cleaning action means it can be used to clean heavily soiled and
contaminated surfaces and the low-foam formula makes it easy to apply.
It will remove dirt, grease, grime and even discolouration caused by the
accumulation of nicotine smoke.
3
1: For every litre of cleaner required, use 45g of Manger’s Sugar Soap
2: Dissolve the powder in warm water
3: Apply using a sponge, working upwards to avoid streaks
4: Rinse with clean water and allow to dry.
Manger’s Sugar Soap is also available in a convenient liquid
concentrate formula – just add warm water.
sugar
soap
mixes up to 22 litres
wipes away grease,
grime & nicotine
the original & the best
500ml ℮
5
Preparation
Remove, treat
and prevent mould
Manger’s Fungicidal Wash kills and prevents the re-appearance of unsightly
growths of mould, algae, fungi, moss and lichen for up to 6 months.
1: Shake before use
3
2: Dilute 1 part Fungicidal Wash to 4 parts clean water in a
clean container
3: Apply liberally by brush
4: Let it dry for 24 hours, then scrape or brush surface to remove all
mould, lichen and algae
5: Re-treat surface with second application
6: Let it dry again for 24 hours before over coating
7: For smaller areas use Manger’s ready-to-use Fungicidal Spray.
fungicidal
wash
kills & removes mould & mildew
inhibits algae & fungal growth
prevents regrowth for up to 6 months
fungicidal
spray
2.5L℮
ready to use
kills & removes mould & mildew
protects against regrowth
500ml ℮
6
Preparation Guide
Removing paint and varnish
Manger’s Paint and Varnish Remover is an extremely effective non-Methylene
Chloride paint stripper. The non-caustic, non-flammable formulation is easy
to use both indoors and out. With its non-drip formulation and minimal
evaporation, it clings to vertical surfaces ensuring there is minimal waste.
7
1: Protect floor coverings, furnishings, textiles and vinyl materials with a
suitable dust sheet
2: Shake container well before use
3: Ensure there is adequate ventilation when working and wear
protective gloves
4: Pour a quantity of Paint and Varnish Stripper into a suitable container
5: Apply a generous even coat onto the surface to be stripped with a
suitable brush but do not brush out
8
6: Leave for approximately 30 minutes then apply a second coat
7: Once the stripper has penetrated the substrate, scrape off, leaving the
surface as clean as possible
8: Rub down the stripped area using a scrubbing brush or stainless steel
pad and water
9: Rinse with water and allow to dry.
paint &
varnish
remover
simple & easy to use
biodegradeable
non-flammable solution
500ml ℮
7
Preparation
Unblocking drains and pipes
Manger’s Caustic Soda is a heavy duty cleaner particularly good for
un-blocking drains and pipes.
1
1: Add approximately 250g of the product gradually to 4 Litres of
cold water
2: Stir well with a wooden stick and avoid splashing
3: The solution will heat up then pour immediately and carefully
down the drain
4: After 20-30 minutes, flush with clean boiling water
5: If blockage is severe, 500g may be required (dilute with 8 litres of
cold water).
3
caustic
soda
unblocks drains & pipes
heavy duty cleaner
effective use as a
paint stripper
500ml ℮
8
CAUTION: THIS SUBSTANCE IS CAUSTIC AND CAN CAUSE SEVERE
BURNS SO ALWAYS FOLLOW SAFETY PROCEDURES CAREFULLY.
USE WITH CAUTION.
1. Keep out of reach of children and animals
2. Always wear gloves and eye protection. NEVER let the solids or the solution
touch skin or clothes
3. Do not use aluminium or galvanised vessels when making up the solution
4. Always use cold water
5. Always add the solids to the water - slowly and gently stirring to avoid
splashing. NEVER add the water to the solids. In this way spillage and heat
generation are reduced
6. Stir with a wooden stick. Wash and dispose of stick safely after use
7. Replace lid tightly if any of the contents remain after use.
Preparation Guide
Cleaning brushes
2
Manger’s Brush Cleaner is formulated with added conditioner to keep your
brushes soft and supple.
1: Pour into a suitable non-plastic container
2: Work well into the brush, roller or pad
3: Soften very hard brushes with Manger’s Paint & Varnish Remover first
4: When clean, drain the brush and pat dry with a clean cloth
4
5: Let paint particles settle, then pour off cleaner for future use.
Cleaning paint from surfaces and hands
Manger’s Ultra Wipes have been specifically designed to remove various paints including emulsions, gloss, lacquer,
varnish, adhesives, sealant, oils, grease, bitumen, dirt and general grime. They are simple to use, fast and convenient
- making them ideal for Professional Decorator’s and to use at home. These multi-purpose wipes can be used for a
wide variety of tasks including:
1:
2:
3:
4:
5:
6:
Cleaning and conditioning the hands (contains lanolin to moisturise the skin)
Cleaning work tools (e.g. paint cans, brushes, rollers, handles etc.)
Cleaning surfaces
Paint spill clean-up
Straightening paint edges
Removing any overspills.
brush
cleaner
for brushes,
rollers and pads
with added conditioner
water rinsable
500ml ℮
ultra
wipes
100 wipes
quick & easy clean up
cleans paint, adhesives,
grease & much more
9
Cleaning
Removing paint from
soft furnishings
2
Manger’s Clean Spirit is a highly effective water-based cleaning alternative to
White Spirit that is safer for both you and the environment. The formulation
contains all biodegradable ingredients and is virtually odourless and nonflammable. Manger’s Clean Spirit can be used to clean all water-based and
most oil-based paint spills from surfaces such as worktops, laminate flooring
and most textiles.
1: First test a small patch for colour fastness in an inconspicuous area
2: Pour a quantity of Manger’s Clean Spirit directly onto the affected area
3: Rub vigorously until the paint has been removed
4: Rinse or wash with clean water
5: Can also be used for cleaning small spills from carpets.
10
Preparation Guide
Cleaning glass surfaces
Manger’s Methylated Spirit is commonly used as a general stain remover and
household cleaner. As a solvent it evaporates quickly and doesn’t leave streaks,
which makes it ideal to clean glass.
1: Dilute 1 part Methylated Spirit to 1 part clean water
2: In warmer temperatures we would recommend using a ratio of 1 part
Methylated Spirit to 4 parts clean water
3
3: Apply using a soft cloth or spray directly onto the glass then wipe off
using paper towels
4: Rub vertically for exterior windows and horizontally for interior glass
A common myth is to use newspaper, which used to work well when it contained lampblack (which was a great
glass polish). However it doesn’t contain it anymore so do not use, as it will leave smear marks.
11
Cracks & gaps
Repairing interior
surface cracks
Manger’s Interior Filler is ideal for broad wall indoor repairs, filling cracks,
gaps and holes. It dries to a tough, smooth surface that is easy to sand and
is so strong that it will take screws and nails when fully set.
3
1: Cover nail and screw heads with an oil-based primer, such as a
Leyland or Johnstone’s All Purpose Primer, prior to application to
prevent rusting
2: Add 1 part water to 2.5 parts of Manger’s Interior Filler
3: Mix thoroughly to a smooth paste
8
t6TFBTUJGGFSNJYXJUIMFTTXBUFSGPSXPPEMBSHFSFQBJSTPS
vertical surfaces
t'JMMFSSFNBJOTXPSLBCMFGPSBQQSPYJNBUFMZÜIPVSBGUFSNJYJOH
4: Push filler into the repair using a filling knife or trowel
5: Allow each layer to dry thoroughly before applying the next
6: Smooth the final layer with a wet filling knife
7: Remove excess filler with a filling knife and allow to dry for at
least an hour
8: If required, rub down with sandpaper when fully dry
9: After use clean mixing bowl and wash any tools in warm water.
interior
filler
mix to paste with water
smooth tough finish
ready to decorate in 1hr
2kg
k ℮
12
Preparation Guide
Fixing intricate and fine
repairs in walls
Manger’s Fine Surface Filler is an ultra smooth, fine particle filler that is ideal
for intricate repairs and for filling minor holes and smoothing out surface
imperfections with no slumping, cracking or shrinking.
1: The area to be repaired should be sanded before application
2: Cover nail and screw heads with an oil-based primer, such as a Leyland
or Johnstone’s All Purpose Primer, prior to application to prevent rusting
3
3: Apply Manger’s Fine Surface Filler with a spatula, spreading a thin
layer of filler over the repair
4: Push filler well into the repair, ensuring that the repair is completely filled
5: For deeper holes, first use Manger’s All Purpose Filler or Ready Mixed
Filler and when dry add a thin layer of Fine Surface Filler
6: Remove excess filler with a spatula and allow to dry for at least 1 hour
7: Product can be sanded when dry if an even smoother finish is desired.
13
Cracks & gaps
Repair ceiling cracks
Manger’s Lightweight Deep Gap Filler fills deep gaps and holes in one
application and is ideal for awkward areas like ceilings.
1: Cover nail and screw heads with an oil-based primer, such as a
Leyland or Johnstone’s All Purpose Primer, prior to application to
prevent rusting
2: Stir to a smooth paste, if product is too dry add a couple of drops of
water and re-stir
3: Apply directly into the gap, ensuring it is completely filled
4: Smooth surface with a wet knife
5: Remove the excess and allow to dry for at least 30 minutes.
4
Fill gaps in your kitchen
or bathroom
Manger’s Kitchen & Bathroom Sealant is a multi-purpose
acetoxy cure silicone sealant that cures quickly to provide a
permanently flexible, high strength waterproof seal. It contains
a powerful anti-fungicide to prevent mould growth. It is ideal
for sealing door and window frames, but has been specifically
formulated as a sanitary sealant for gaps around baths,
showers, kitchens, taps and tiles. It adheres readily without a
primer to glass, ceramic, vitreous surfaces and painted surfaces.
14
Preparation Guide
Fill gaps in your kitchen or bathroom: (cont)
1: Any loose or flaking material, and old sealant, should be removed before application
2: Glass, metal and aluminium should be cleaned with a solvent cleaner such as white spirit prior to application
for optimum results
3: Porous surfaces may require priming - test a small area first
4: Apply the sealant in a continuous motion, making sure that all air pockets are eliminated
5: Using a dry spatula, tool the sealant with light pressure to spread the material against the joint surfaces
6: For the best performance, the sealant should only be bonded to the two facing sides of the joint
7: Excess uncured sealant should be wiped and removed with a solvent cleaner.
Gaps between skirting boards and
joints subject to movement
Manger’s Decorator’s Caulk delivers a permanently flexible acrylic seal that will
outperform traditional paste fillers when used in areas subject to movement. It
can be used both indoors and out – between brick, concrete, stone, timber and
pointing around door/window frames providing up to 10 years life.
3
1: Surfaces may be damp but must be clean and free from dust, dirt, frost,
grease and other contamination
2: Cut nozzle to the required joint size at an angle of 45°
3: Gun sealant firmly into the joint to provide a good solid fill
4: Joints 6mm wide up to 15mm wide can be sealed to a matching depth
5: Reduce depth of deeper joints to maximum 12mm using Manger’s
Expanding Foam Filler
6: Finish sealant run slightly proud to allow for normal drying/shrinkage
7: Paintable after approximately 1 hour. Please note drying times can vary
depending on temperature, relative humidity and the joint size.
15
Cracks & gaps
Large, awkward and
irregular gaps
Manger’s Expanding Foam Filler is a one-part polyurethane foam that
expands rapidly on contact with air. It will mould itself to the most awkward
gaps, cavities and cracks providing a strong permanent filler that can be
finished to suit a wide range of applications.
5
1: Surfaces should be free from dust and grease
2: Turn can upside down and shake vigorously for 30 seconds
3: Screw applicator and tube firmly on to valve
4: Hold can in an upside-down position arranging your fingers comfortably on the applicator head
5: Apply pressure to the applicator easing the foam into the cavity at a
controlled rate
8
6: Only half fill the cavity as the foam will continue to expand.
7: The foam will remain tacky for 3-4 minutes. Clean off any spillages
whilst foam is still wet using a dry cloth
8: Expanding Foam Filler can usually be cut and shaped after approximately 45 minutes
9: After 2-3 hours (when curing is complete) it can be sanded down,
rendered, plastered, smooth-filled or painted.
expanding
foam
filler
fills gaps of all
shapes & sizes
easily trimmed, sanded,
plastered or painted
strong, permanent filler
300ml ℮
16
Preparation Guide
Damaged exterior surfaces
Manger’s Ready Mixed Filler is ideal for repairing and filling cracks, gaps and
holes in most common surfaces outdoors. It dries to a tough, weather resistant
surface that is smooth and easy to sand and is so strong that it will take screws
and nails when fully set.
5
1: Ensure the wall is dry and free from dust and dirt
2: Cover nail and screw heads with an oil-based primer, such as a Leyland
or Johnstone’s All Purpose Primer, prior to application to prevent rusting
3: Stir filler to a smooth consistency, adding one or two drops of water
if required
4: Apply filler in layers up to 1cm thick with a filling knife
5: Allow each layer to dry thoroughly before applying the next smoothing
the final layer with a wet filling knife
6: Remove excess filler with a filling knife and allow to dry for at least 1
hour
8
7: If required, rub down with sandpaper when fully dry. Wear a suitable
face mask when dry sanding
8: Seal the repair, with oil-based All Purpose Primer.
ready
mixed
filler
ready to use
multi-surface interior
and exterior use
quick drying, smooth
and tough
330g ℮
17
Papering
Tips for perfect papering
3
Manger’s All Purpose Wallpaper Adhesive mixes easily to form a smooth,
lump free paste. It is suitable for hanging all types of wallpaper and its
extra strong formula has been specially developed to give much improved
brush on characteristics for easier wallpapering.
1: Remove all traces of old wallpaper
2: Use Manger’s All Purpose Filler to fill any holes and cracks to ensure
a smooth finish. Use Manger’s Lightweight Deep Gap Filler to fill deep
holes and ceiling cracks
3: Sprinkle the contents of a sachet into water, mixing briskly for 30
seconds to ensure dispersion. Leave for 3 minutes and stir thoroughly
5
4: If you wish to hang wallpaper on walls which were previously painted,
roughen the surface with a mildly abrasive sandpaper in order to
achieve effective adhesion
5: Size porous walls or new plaster before papering with a thin solution
of Mangers All Purpose Wallpaper Adhesive
6: Prevent air bubbles by ensuring sufficient adhesive is applied to the
whole surface of the wallpaper.
all purpose
wallpaper
adhesive
mixes quickly to a smooth paste
suitable for any wallcovering
protects against mould
5 roll pack ℮
18
Preparation Guide
Tips for perfect papering: (cont)
7: Apply straight from the centre of the strip to the edges and soak as
per the wallpaper manufacturers guidelines
8: After application, brush paper from centre of the strip to the edge to
remove bubbles
7
9: Prevent edge curl by using adequate paste on the edges of
the wallpaper
10: Use a seam roller to press down the edges and wipe off excess
paste from the surface of the paper immediately with a damp cloth.
Alternatively use Manger’s Border & Overlap Adhesive to ensure
edges do not lift.
To estimate the number of wallpaper rolls needed to paper a room, use the table below:
Wall Height
Distance around
the room
2.0 – 2.4m
2.4 – 2.8m
2.8 – 3.m
10m
5
5
6
12m
6
6
7
14m
7
7
8
16m
8
9
9
18m
9
10
11
20m
10
11
12
22m
10
12
13
24m
11
13
14
19
Papering
Hanging heavier
wallpaper or in areas
prone to condensations
Manger’s Ready Mixed Wallpaper paste is a super strong, ready to use
adhesive with easy slide properties for easier papering. It is suitable for
hanging all types of heavyweight and luxury wallcoverings, including
paper and fabric backed vinyls, tiling on a roll, hessians, grasscloths and
polystyrene tiles, veneers and covings. It is also great to use in most areas,
especially in kitchens, bathrooms and behind radiators, where fluctuations
in temperature and humidity levels may occur.
6
1: Surfaces should be clean, dry and free from dust
2: Size absorbent surfaces
3: Sand low or non-absorbent surfaces, such as gloss painted walls, to
provide a key and cross line with lining paper
4: Manger’s Ready Mixed Wallpaper paste contains an algaecide,
however areas with a high risk of mould growth should be treated
with Manger’s Fungicidal Spray beforehand
5: Always follow the wallpaper manufacturer’s instructions
6: Generously apply adhesive to paper with a brush or roller, unless
otherwise instructed, paying particular attention to edges
7: Take care to keep printed surface free from adhesive
8: When hanging your border, finishing overlapping seams or for general
wallcovering repairs, use Manger’s Border & Overlap Adhesive.
20
Preparation Guide
Sizing walls prior
to papering
Sizing is an important step in creating a good foundation for wallpaper, it
creates a uniform surface that allows wallpaper to dry smoothly and last for
years. Sizing coats the wall to so that your wallpaper applies a uniform way,
and it will reduce the amount of paste a wall will absorb. One of the simplest
ways to size your walls is to coat them with a thinned down version of the
adhesive that will ultimately be used when applying your wallpaper. It also
allows easier adjustability for a longer time with the paper for better
edge matching.
1
1: Sprinkle the contents of one 195g sachet into 12 Litre cold water,
mixing briskly for 30 seconds to ensure dispersion
2: Leave for 3 minutes then stir thoroughly
3: Alternatively, if you are using Manger’s Ready Mixed Wallpaper Paste,
dilute with an equal amount of clean water
4
4: Using a roller, apply to the wall area to be papered and brush in
around the edges
5: All the walls being papered should be sized at the same time;
beginning at the point where the wallpapering will begin
6: The wallpaper hanging can begin almost as soon as the application of
the size is done.
21
Papering
Mend wallpaper repairs
Manger’s Border & Repair Adhesive is a handy tube of our super
strength gel. It will stick to gloss and emulsion paint, and is suitable
for sticking down overlapping seams or curled edges as well as general
wallpaper repairs.
1
1: Using the nozzle to target the correct area, apply adhesive to the wall
where the wallpaper is to be repaired
2: Using a spatula, evenly spread adhesive on the wall
3: Moisten the back of vinyl and heavier wallcoverings with clean water
4: Press down firmly
5: Wipe off excess from the surface of the paper immediately with a
damp cloth.
border
& repair
adhesive
for hanging borders
extra strong
sticks vinyl to vinyl
250g ℮
22
Preparation Guide
Hanging a border
Manger’s Border & Overlap Adhesive is a specially formulated, super strength
gel for hanging all types of borders, even sticking vinyl to vinyl.
1: Always follow the border manufacturer’s instructions
3
2: Cut the border to required length
3: Evenly spread adhesive onto the border to ensure complete coverage
4: Position border on top of the wallpaper
5: Smooth down firmly with a sponge or brush
6: Take care to keep printed surface free from adhesive.
23
Tiling
Applying wall tiles
Manger’s Non Slip Wall Tile Adhesive has excellent non-slip properties
making it ideal for fixing most types and sizes of ceramic wall tiles. This
easy to apply adhesive is suitable for use in bathrooms and kitchens and is
specially formulated to allow time for adjustment after fixing.
6
1: Surfaces must be dry, free from dust, dirt, grease and other loose material
2: Wallpaper, emulsion paint or other weakly bonded finishes should
be removed
3: Score the surface of glazed tiles to provide a good key
4: Timber or plasterboard partitioning must be rigidly fixed
5: Treat timber surfaces in areas of water contact e.g. showers, with a
water resistant sealer before tiling commences
8
6: Apply enough adhesive to cover an area of approx. 0.5m squared
using a notched spreader
7: For frequently wet areas, e.g. showers, spread adhesive as a 3mm
continuous bed and lightly rib the surface with a notched spreader
8: Bed tiles into the adhesive using a twisting action to ensure complete
contact between the tile and adhesive
9: For tiles that are studded on the back, ensure sufficient adhesive is
applied to cover them
10: Remove any excess adhesive from the face of the tiles with a damp
cloth within 20 minutes
11: Leave tiles for at least 24 hours before grouting
12: The contents of one 10 Litre tub of Manger’s Non Slip Tile Adhesive
will tile approximately 11 square metres.
24
Preparation Guide
Wall tile repairs
A marked or cracked tile can look really unappealing but, as Manger’s
All-in-1 Wall Tile Adhesive & Grout is formulated for both fixing and grouting
ceramic wall tiles, it can be easy to fit a new one. For use on most interior
surfaces including cement rendering, plaster, plasterboard, existing tiles,
wood and wood composites.
1
1: Using a chisel and a mallet, carefully knock out both the damaged tile and
the old dry adhesive from the wall
2: Brush down surfaces to ensure they are dry and free from dust, dirt, grease
and other loose or flaking material
4
3: Apply Adhesive & Grout to the back of the replacement tile with a notched
flexible spreader
4: Push the new tile into place, making sure the surface is level with the
surrounding tiles
5: Remove any excess adhesive from the face of the tiles with a damp cloth
within 20 minutes
6: Leave tiles for at least 4 hours, or 16 hours if tiling on non-porous surfaces
7: Press grout firmly into joints to ensure they are well filled and any air
pockets have been expelled.
8
8: Smooth off by running a grout finisher or a round end of a pencil along the
joint line
9: Remove any excess grout immediately with a damp cloth or sponge
10: When grout has dried, polish tiles with a damp cloth
11: Do not wet the tiles for at least 24 hours to allow the grout to
harden thoroughly.
25
Range overview
sugar
soap
cleaning
mixes up to 22 litres
wipes away grease,
grime & nicotine
sugar
soap
spray
the original & the best
500ml ℮
mixes up to 22 litres
wipes away grease,
grime & nicotine
the original & the best
500ml ℮
Product
Sugar Soap
Sugar Soap Concentrate
Sugar Soap Spray
Caustic Soda
Fungicidal Wash
Fungicidal Spray
Paint & Varnish Remover
Ultra Wipes
Brush Cleaner
ultra
wipes
fungicidal
wash
fungicidal
spray
kills & removes mould & mildew
caustic
soda
inhibits algae & fungal growth
prevents regrowth for up to 6 months
2.5L℮
unblocks drains & pipes
ready to use
heavy duty cleaner
effective use as a
paint stripper
kills & removes mould & mildew
protects against regrowth
500ml ℮
500ml ℮
paint &
varnish
remover
100 wipes
quick & easy clean up
cleans paint, adhesives,
grease & much more
simple & easy to use
biodegradeable
non-flammable solution
500ml ℮
Sizes Available
450g (10ltr mix)
500ml
500ml
500g
2.5ltr
500ml
500ml
100 wipes
500ml
1.35kg (30ltr mix)
1ltr
-
2.5ltr
-
5ltr
-
border
& repair
adhesive
all purpose
adhesives
wallpaper
adhesive
26
sticks vinyl to vinyl
250g ℮
protects against mould
5 roll pack ℮
Product
All Purpose Wallpaper Adhesive
Ready Mixed Wallpaper Paste
Border & Overlap Adhesive
Border & Repair Adhesive
All-in-1 Wall Tile Grout & Adhesive
Non Slip Wall Tile Adhesive
for hanging borders
extra strong
mixes quickly to a smooth paste
suitable for any wallcovering
Sizes Available
95g (5 roll)
1kg
500g
250g tube
2.2ltr
10ltr
195g (10 roll)
2.5kg
4.4 ltr
-
3 x 195g (30 roll)
4.5kg
-
10kg
-
brush
cleaner
for brushes,
rollers and pads
with added conditioner
water rinsable
500ml ℮
Preparation Guide
cleaners
fillers
adhesives
solvents
ready
mixed
filler
interior
all purpose
filler
mix to paste with water
no slumping, cracking or shrinking
use on multiple surfaces
filler
expanding
foam
filler
ready to use
multi-surface interior
and exterior use
quick drying, smooth
and tough
mix to paste with water
smooth tough finish
330g ℮
fillers
ready to decorate in 1hr
fills gaps of all
shapes & sizes
easily trimmed, sanded,
plastered or painted
strong, permanent filler
500g ℮
2kg
k ℮
300ml ℮
Product
All Purpose Filler
Interior Filler
Ready Mixed Filler
Fine Surface Filler
Lightweight Deep Gap Filler
Expanding Foam Filler
Decorator’s Caulk
Kitchen & Bathroom Sealant
Sizes Available
500g
2kg
330g tube
600g
500ml
300ml
295ml
295ml
2kg
600g
1ltr
750ml
385ml
-
5kg
1kg
-
10kg
2kg
-
solvents
Product
White Spirit
Turpentine Substitute
Clean Spirit
Methylated Spirit
Sizes Available
750ml
750ml
750ml
500ml
2ltr
2ltr
-
4ltr
-
-
27
Decorating
Problems FAQs
cleaners
fillers
adhesives
solvents
What’s the best way to remove existing
paper from the wall?
The key to successful removal is water. The common factor about most wallpaper adhesives is that if you wet them
they will reactivate and become soft. However most wallcoverings have some form of moisture protection on the face
of them. To successfully remove the paper, you need to get the water through the coating and into the adhesive. In
most cases the use of a steamer will give the best results. You should be able to find one from a tool hire shop or
your local decorating store from between £5 - £15 per day or you might be able to find one to buy from £30.
When should I use fungicidal wash?
Manger’s Fungicidal Wash is a preparatory sterilising solution designed to be applied to bare walls to kill any
mould spores before decorating. Whilst it’s seen to be most beneficial in areas that might have a moisture problem,
like kitchens, bathrooms and cellars, it’s actually safe to use in any area of the house. Manger’s also has a ready to
use spray version in the range for convenience, when tackling small areas of mould growth.
28
Preparation Guide
What is ‘keying’?
It is mostly considered necessary for surfaces to be as smooth as possible for the best finish when decorating.
However there are circumstances where it is thought to be required to roughen up the surface first in order to give
an adhesive something to grab onto.
When tiling or papering, surfaces should be clean, dry and free from any loose or flaking material and keying will
help to remove any imperfections, such as loose grit, filler or flaky paint etc. Keying is a straightforward process
where the surface is rubbed down with, glass or sand paper. Light grooves may also be added afterwards but this is
dependant on the type of surfaces. Once the keying is complete it is essential that the surface is cleaned down with
Manger’s Sugar Soap to remove any dust, as this will also hinder adhesion if left on.
What paint should I choose?
Generally, the best paint for your internal walls and ceilings is emulsion. There are three main finishes of emulsion:
Matt
Vinyl matt emulsion gives a non-shiny finish that is perfect for hiding small imperfections on walls or ceilings; a
glossier finish will reflect light and highlight any flaws. Vinyl matt emulsion might not wear quite as well as shinier
emulsions so look out for durable matt emulsions made with acrylic.
Soft Sheen
Vinyl soft sheen emulsion has a subtle soft-sheen finish, which reflects light back into a room and is more durable
than vinyl matt. It’s great for areas that might need a light wash once in a while.
Silk
Vinyl silk emulsion offers a high-sheen finish and is the most durable of all the emulsion paints. Use for rooms
prone to moisture such as condensation. If you’re considering a silk product, but you prefer a lower sheen finish, you
might also be interested in buying paint made specifically for kitchens and bathrooms, which generally comes in a
mid-sheen finish.
29
Decorating
Problems FAQs
cleaners
fillers
adhesives
solvents
What order should I paint my room in?
Paint the ceilings first and then all your walls. All the woodwork should be painted last.
Do I need to use lining paper?
Use lining paper to cross-line a wall if you’re hanging embossed or expensive wallcoverings, or if the wall has
imperfections that might show through your wallpaper. Lining paper is usually hung horizontally so the joins don’t
match up with those on the top layer. If you’re going to paint over the lining paper, hang it vertically.
What is sizing?
Sizing, or size, is a weakened mix of wallpaper adhesive that is used to fill up a porous surface, i.e. plaster. It’s purpose
is to stop the wall from taking too much moisture from the back of the wallpaper and causing it to peel when dry.
30
Preparation Guide
What brush should I use to paint?
There are 2 main types of brushes to choose from: synthetic and natural bristles.
Synthetic brushes are very hard wearing and can last up to 5 times as long as a natural brush. As synthetic bristles
do not absorb large amounts of water and swell up they do not cause tramlines to appear in the paint. Their
structure produces a fine finish with all water-based paints.
Natural bristle has a structure that allows it to take and hold paint within the brush. In addition, the split ends
of bristle brushes help to produce a fine finish with traditional solvent paint but they do not perform as well with
water-based paints.
Brushes come in many sizes. As a rule of thumb, the larger the area you are painting, the larger the brush that you
should use. For walls a 2” or 3” brush is required for cutting in, whilst a 1” or 2” brush will give you more flexibility
when painting doors, skirting boards & architraves.
Why should I use a different adhesive for
hanging my border?
Manger’s Border & Overlap Adhesive and Manger’s Border & Repair Adhesive are different to Manger’s Wallpaper
Adhesive as they are not starch based. This issue is not the border itself but the surface it is being hung onto. We
would always recommend that when hanging borders you use the appropriate adhesive to stick “vinyl to vinyl”.
31
From the makers of
Johnstone’s and Leyland
Tel:
+44 (01924) 354354
Email: [email protected]
PPG Architectural Coatings UK Limited, Huddersfield Road, Birstall, Batley, West Yorkshire WF17 9XA. Tel: 01924 354000
Manger’s is a registered trademark of PPG Architectural Coatings UK Ltd.