refrigeration products

Transcription

refrigeration products - Heatcraft Worldwide Refrigeration

CH-CC
June 2009
Replaces CH-CC, 04/07
REFRIGERATION
PRODUCTS
Condensed Catalog
www.chandlerref.com
Table of Contents
Reach-In Unit Coolers
Condensing Units
Model TA Thin Profile Air Defrost....................................................3
Model CH 1/2-5 HP Hermetic Indoor/Outdoor...................... 16
Model TL Thin Profile Electric Defrost...........................................3
Model CZ 2-6 HP Scroll® Indoor/Outdoor................................ 17
Model C High Profile Air Defrost.....................................................3
Model CS 1/2-5 HP Semi-Hermetic Indoor/Outdoor............ 17
Model VA V-Profile Air Defrost.........................................................4
Models HDT, HDN, HDS 3-22 HP Discus® Indoor/Outdoor.18
Models BBM, BBL Back Bar................................................................4
Models HZT, HZN, HZS 3-22 HP Scroll® Indoor/Outdoor.... 18
Model KMK Standard Mullion..........................................................4
Model HDH 20-40 HP Discus® Outdoor..................................... 19
Model RAMK Reverse Air Mullion...................................................5
Model HDD 24-80 HP Dual Compressor Outdoor................. 20
Model BTO Twin Flow.........................................................................5
Model HWN 1/2-6 HP Hermetic Indoor Water-Cooled........ 21
Model U Dual Aire®..............................................................................5
Model ZWN 1/2-6 HP Scroll® Indoor Water-Cooled............... 21
Models LTA, LTL Extened Thin Profile Unit Cooler.....................6
Model SWN 3/4-20 HP Indoor Water-Cooled.......................... 22
Model SRN 3/4-20 HP Remote Indoor....................................... 23
Walk-In Unit Coolers
Model RLC Low Profile Air Defrost.................................................6
Air-Cooled Condensers
Models ELC, EFC Low Profile Electric Defrost.............................7
Model WSS 1-26 Tons....................................................................... 24
Model GLC Low Profile Hot Gas Defrost.......................................7
Model HNE EC Series........................................................................ 25
Model LAH Low Flow Low Velocity Air Defrost..........................8
Models HNQ, HNX 830/540 Series............................................... 26
Model LAL Low Flow Low Velocity Electric Defrost.................8
Models HNL, HNH 830/540 Series............................................... 27
Model LAG Low Flow Low Velocity Hot Gas Defrost...............8
Model HWA Low Velocity Center Mount Air Defrost...............9
Model HWE Low Velocity Center Mount Electric Defrost......9
Model HWG Low Velocity Center Mount Hot Gas Defrost....9
Fluid Coolers
Model WGS Direct-Drive...................................................................28
Model HFS Direct-Drive.....................................................................28
Model TLH Center Mount Air Defrost......................................... 10
Refrigeration Controls and Technology
Model TLL Center Mount Electric Defrost................................ 10
Beacon II™ Electronic Control Board.......................................... 29
Model HMA Medium Profile Air Defrost.................................... 10
Beacon II™ Smart Controller.......................................................... 29
Models HME, HML Medium Profile Electric Defrost.............. 11
Beacon II™ Smart Defrost............................................................... 29
Models HMG, HMF Medium Profile Hot Gas Defrost............ 11
Beacon II™ Smart Software............................................................ 29
Smart Defrost Kit™............................................................................ 29
Warehouse Unit Coolers
Model HHA High Profile Air Defrost........................................... 12
Additional Products from Chandler
Models HHE, HHL High Profile Electric Defrost...................... 12
Mohave™ Hot Gas Defrost ............................................................ 30
Models HHG, HHF High Profile Hot Gas Defrost.................... 13
FlexPack™ ............................................................................................ 30
Packaged Refrigeration Systems
Engineered Solutions
Models PTT, PTN PRO3 Top Mount ............................................. 14
Air Handlers . ...................................................................................... 31
Model PST PRO3 Side Mount ........................................................ 15
Indoor and Outdoor Racks ........................................................... 31
Customer Specific Orders . ............................................................ 31
E Solutions™ branded products and options are designed to exceed current energy and environmental
standards. We have made a conscious commitment to developing environmentally innovative products
that allow our customers to make energy efficient, eco-conscious choices. Products included in the
E Solutions portfolio reduce costs, improve bottom lines, and enhance both equipment performance and
service life.
Look for this mark throughout the catalog for products with features and options available to reduce energy
consumption and environmental impact. Visit www.heatcraftrpd.com/esolutions for more information.
© 2009 Heatcraft Refrigeration Products, LLC
2
Thin Profile Air Defrost Unit Coolers
Model TA reach-in evaporators are thin units that mount in the top of a refrigerator, making the entire top shelf area
usable. The attractive low silhouette makes this unit particularly desirable for display-type refrigerators. It can also be
used in back bars, under counter cabinets or wherever space is at a premium.
Drain fitting at 45° angle so drain can be run through the back or bottom of refrigerator. Room for expansion valve
inside so that it is out of sight. Model TA is available with optional coated coil for corrosion protection (use model
designation TAK). Also features sweat inlet connection to reduce leaks.
TA (K)
Model
TA10
TA13
TA17
TA23
TA30
TA43*
TA55*
Capacity
(BTUH)
Fan
10°F TD
+25 SST
Qty.
CFM
1,000
1,300
1,700
2,300
3,000
4,300
5,500
1
2
2
3
3
4
5
120
170
210
330
360
540
650
Motor (Total FLA)
Shaded Pole
208115/1/60
230/1/60
0.8
0.4
1.6
0.8
1.6
0.8
2.4
1.2
2.4
1.2
3.2
1.6
4.0
2.0
Dimensions (in.)
Connections (in.)
L
H
D
Liquid
OD
16-1/2
20-1/2
24
31-5/8
40
53-3/8
53-3/8
4-1/2
4-1/2
4-1/2
4-1/2
4-1/2
4-1/2
6-3/4
13-1/2
13-1/2
14-1/2
14-1/2
14-1/2
14-1/2
14-1/2
3/8
3/8
3/8
3/8
3/8
1/2
1/2
Suction
ID
Drain
OD
3/8
3/8
3/8
3/8
1/2
5/8
5/8
1/2
1/2
1/2
1/2
1/2
1/2
1/2
Approx.
Net Wt.
(lbs.)
10
13
17
23
26
36
45
* These models use external equalized expansion valve
Thin Profile Electric Defrost Unit Coolers
Model TL low temperature reach-in evaporators have an automatic defrost system. Mounted in the top of a refrigerator,
its extremely compact cabinet makes it possible to utilize the entire top shelf area for storage. With a normal operating
range of 15°F to –20°F, This unit is ideally suited for such applications as commercial freezers, ice cream boxes, bakery
freezers and dual-temp reach-in boxes. Mechanical contact is provided between the heater elements and the drain
pan, ensuring a warm pan during the defrost cycle. Sufficient space is provided to mount the expansion valve within
the cabinet. Systems for both 115 volt and 208-230 volt operation are available. Also features sweat inlet connection
to reduce leaks. Some models available with EC motors, contact your sales representative for availability.
TL
Model
Capacity
(BTUH)
Fan
Motor (Total FLA)
Shaded Pole
10°F TD
Qty. CFM
208-10°F SST
115/1/60
230/1/60
TL09
900
1
110
0.8
0.4
TL12
1,200
2
210
1.6
0.8
TL16
1,600
2
210
1.6
0.8
TL21
2,100
1
240
1.0
0.5
TL28
2,800
3
335
1.2
TL35*
3,500
2
420
1.0
TL53*
5,300
3
595
1.5
* These models use external equalized expansion valve
Defrost Heater
Dimensions (in.)
115/1/60 230/1/60
Watts
475
600
700
1,100
1,430
1,600
1,950
Amps
Amps
4.1
5.2
6.1
9.6
-
2.1
2.6
3.0
4.8
5.7
7.0
8.5
Connections (in.)
L
H
D
Liquid
OD
Suction
ID
Drain
OD
16-1/2
20-1/2
24
24
31-5/8
38-3/8
49-1/8
4-1/2
4-1/2
4-1/2
6-3/4
6-3/4
6-3/4
6-3/4
13-1/2
13-1/2
14-1/2
16-1/2
14-1/2
16-1/2
16-1/2
3/8
3/8
3/8
3/8
3/8
1/2
1/2
3/8
1/2
1/2
1/2
1/2
5/8
7/8
1/2
1/2
1/2
1/2
1/2
1/2
1/2
Approx.
Net Wt.
(lbs.)
10
15
19
19
22
31
45
High Profile Air Defrost Unit Coolers
Model C unit coolers are ideal for refrigerated reach-ins. It mounts to the top of the refrigerator and discharges cold
air against the back wall. With this air flow pattern, the air is not blasted on the product, but is diffused along the back
wall and then gently drawn across the product as it returns to the unit; thus, uniform temperatures are maintained
throughout the refrigerator. In addition, door sweating and refrigeration loss due to door opening is greatly reduced
because the air is not discharged against the doors. Mounting is easy with aluminum hangers that automatically space
the unit the correct distance from the back wall. The expansion valve fits inside, out of sight. Model C is available with
an optional coated coil (designated as model CK) for corrosion protection. Also features sweat inlet connection to
reduce leaks. Some models available with EC motors, contact your sales representative for availability.
C (K)
Model
Capacity
(BTUH)
Fan
Motor (Total FLA)
Shaded Pole
Qty. CFM
208115/1/60
230/1/60
C13
1,300
1
235
1.0
0.5
C17
1,700
1
250
1.0
0.5
C23
2,300
1
265
1.0
0.5
C30
3,000
2
480
2.0
1.0
C43*
4,300
2
520
2.0
1.0
* Size 43 uses external equalized expansion valve
10°F TD
+25 SST
Dimensions (in.)
Connections (in.)
L
H
D
Liquid
OD
14-1/4
17-1/4
22-3/4
27-3/4
38
8-7/8
8-7/8
8-7/8
8-7/8
8-7/8
13-3/4
13-3/4
13-3/4
13-3/4
13-3/4
3/8
3/8
3/8
3/8
1/2
Suction
ID
Drain
OD
3/8
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
Approx.
Net Wt.
(lbs.)
12
12
17
21
33
3
V-Profile Air Defrost Unit Coolers
Model VA
reach-in evaporators are deluxe units designed for use in small reach-ins, back bar and
under counter refrigerators, and many other applications where a small, compact unit is required. The
thermal expansion valve mounts inside of the unit. The unit can be mounted from the ceiling or off the
back or end walls, or can be used in mullion application. VA is available with an optional coated coil for
corrosion protection (use model designation VAK). Also features sweat inlet connection to reduce leaks.
Some models available with EC motors, contact your sales representative for availability.
VA (K)
Model
VA06
VA08
VA12
VA17
Capacity
(BTUH)
Fan
Motor (Total FLA)
10°F TD
+25 SST
Qty.
CFM
600
800
1,200
1,700
1
1
2
1
135
130
265
245
Dimensions (in.)
Shaded Pole
208115/1/60
230/1/60
0.8
0.4
0.8
0.4
1.6
0.8
1.0
0.5
Connections (in.)
L
H
D
Liquid
OD
12-1/2
12-1/4
18
14
6-7/8
6-7/8
8
9-3/4
8-1/8
8-1/8
8-1/8
10-1/2
3/8
3/8
3/8
3/8
Suction
ID
Drain
OD
3/8
3/8
3/8
3/8
1/2
1/2
1/2
1/2
Approx.
Net Wt.
(lbs.)
7
7
12
9
Back Bar Unit Coolers
Models BBM/BBL back bar unit coolers are available in either air or electric defrost. These compact,
wall-mounted units are suitable for 35°F to 40°F (BBM medium temp. models) and 0°F to -10°F (BBL low
temp. models) under-counter reach-in fixtures. Motors are thermally protected and lifetime lubricated.
Fan blades and guards are molded from corrosion-proof Lexan®. Housing is made of grained aluminum
for long life and easy cleaning. Also features sweat inlet connection to reduce leaks.
Capacity
(BTUH)
BB
Model
BBL10
BBM11
BBL15
BBM16
Fan
Motor (Total FLA)
10°F TD
+25 SST
Qty.
CFM
HP
1,000
1,100
1,500
1,600
1
1
2
2
90
90
180
180
1/150
1/150
1/150
1/150
Heater
Shaded Pole
115/1/60
0.8
0.8
1.6
1.6
208230/1/60
0.4
0.4
0.8
0.8
Watts
275
350
-
Dimensions (in.)
115/1/60
208230/1/60
Amps
Amps
2.7
3.5
-
1.4
1.7
-
Connections (in.)
L
H
D
Liquid
OD
19-3/4
19-3/4
26-1/4
26-1/4
14
14
14
14
5-1/2
5-1/2
5-1/2
5-1/2
1/2
1/2
1/2
1/2
Standard Mullion Unit Coolers
Model KMK
standard mullion unit coolers are ideal for use in under-counter reach-in refrigeration.
The thin-line design allows the unit to be mounted behind a mullion with sufficient clearance for the
installation of tray slides. KMK has a unique fan arrangement that allows air to be drawn into the top of
the unit, pulling return air from both sides of the mullion. This arrangement allows the coldest air to be in
contact with drop-in trays.
The versatile design of these compact mullions is also adaptable for mounting on the back wall or ends of
a beverage cooler. The finned coil of KMK is protected by special coating as standard. Also features sweat
inlet connection to reduce leaks.
KMK
Model
KMK13
KMK17
KMK23
4
Capacity
(BTUH)
Fan
10°F TD
+25 SST
Qty.
CFM
1,300
1,700
2,300
2
2
3
180
170
255
Motor (Total FLA)
Shaded Pole
208115/1/60
230/1/60
1.6
0.8
1.6
0.8
2.4
1.2
Dimensions (in.)
L
H
15-5/8 17-3/4
15-5/8 19-3/4
22
19-3/4
Connections (in.)
D
Liquid
OD
Suction
ID
Drain
OD
5-5/8
5-5/8
5-5/8
3/8
3/8
3/8
3/8
3/8
1/2
5/8
5/8
5/8
Approx.
Net Wt.
(lbs.)
15
17
23
Suction
ID
Drain
OD
3/8
3/8
3/8
3/8
1/2
1/2
1/2
1/2
Approx.
Net Wt.
(lbs.)
13
12
15
14
Reverse Air Mullion Unit Coolers
Model RAMK reverse air mullion unit coolers are ideal for use in under-counter reach-in refrigeration. The
thin-line design allows the unit to be mounted behind a mullion with sufficient clearance for the installation
of tray slides. RAMK or Reverse Air Mullion draws air through the coil at the bottom and discharges the
cooled air out the top. This arrangement allows the coldest air to be in contact with drop-in trays.
The versatile design of these compact reverse air mullions is also adaptable for mounting on the back wall
or ends of a beverage cooler. The finned coil of RAMK is protected by special coating as standard. Also
features sweat inlet connection to reduce leaks.
RAMK
Model
RAMK13
RAMK17
RAMK23
Capacity
(BTUH)
Fan
10°F TD
+25 SST
Qty.
CFM
1,300
1,700
2,300
2
2
3
180
170
255
Motor (Total FLA)
Shaded Pole
208115/1/60
230/1/60
1.6
0.8
1.6
0.8
2.4
1.2
Dimensions (in.)
L
D
Liquid
OD
Suction
ID
Drain
OD
5-5/8
5-5/8
5-5/8
3/8
3/8
3/8
3/8
3/8
1/2
5/8
5/8
5/8
H
15-5/8 17-3/4
15-5/8 19-3/4
22
19-3/4
Connections (in.)
Approx.
Net Wt.
(lbs.)
15
17
23
Twin-Flow Unit Coolers
Model BTO twin-flow unit cooler is a compact design with medium velocity airflow. The unit is mounted
flush to the ceiling and draws air in through the fan and discharges out both sides. The air pattern reduces
air loss when doors are opened and the medium velocity reduces product drying. Twin-flow units are for
applications of 35˚F and higher. Box temperatures are kept more constant throughout and fresh products
last longer. Seven sizes are available with BTUH from 900 to 5,500 at 10˚TD. The BTO is available with an
optional coated coil for corrosion protection (use model designation BTOK). Also features sweat inlet
connection to reduce leaks.Some models available with EC motors, contact your sales representative
for availability.
BTO (K)
Model
BTO09
BTO13
BTO18
BTO25*
BTO35*
BTO45*
BTO55*
Capacity
(BTUH)
Fan
10°F TD
+25 SST
Qty.
CFM
900
1,300
1,800
2,500
3,500
4,500
5,500
1
2
1
2
2
2
1
130
240
255
460
425
550
730
Motor (Total FLA)
Shaded Pole
208115/1/60
230/1/60
0.8
0.4
1.6
0.8
1.0
0.5
2.0
1.0
2.0
1.0
2.0
1.0
2.1
1.1
Dimensions (in.)
Connections (in.)
L
H
D
Inlet
OD
19-1/8
19-1/8
19-1/8
26-1/8
26-1/8
29-1/8
29-1/8
4-7/8
5-3/4
5-3/4
6-3/4
6-3/4
9-1/4
8-1/2
16-1/8
16-1/8
16-1/8
18-1/8
18-1/8
21-1/8
21-1/8
1/2
1/2
1/2
1/2
1/2
1/2
1/2
Suction
ID
Drain
OD
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
5/8
5/8
Approx.
Net Wt.
(lbs.)
9
11
12
19
20
29
29
* These models use external equalized expansion valves
Dual Air Unit Coolers
Model U unit cooler is used wherever a small, compact unit is required, such as salad boxes, back bars
and direct-draw boxes. It can be mounted on the ceiling or wall. The Model U unit draws air in through
the front and discharges it out both sides to ensure proper distribution of cool air and maintain a uniform
box temperature. Also features flare connections.
U is available with an optional coated coil for corrosion protection (use model designation UK).
U (K)
Model
U09
U12
U15
Capacity
(BTUH)
10°F TD
+25 SST
850
1,150
1,500
Fan
Qty. CFM
1
1
1
190
250
310
Motor (Total FLA)
Shaded Pole
208115/1/60
230/1/60
0.45
0.55
0.45
0.55
1.10
0.55
Dimensions (in.)
Connections (in.)
L
H
D
Liquid
FN
Suction
ID
Drain
OD
11-1/2
17-1/2
17-1/2
8-1/2
8-1/2
9-1/2
8-7/8
8-7/8
10-7/8
1/2
1/2
1/2
3/8
3/8
3/8
1/2
1/2
1/2
Approx.
Net Wt.
(lbs.)
8
8
12
5
Extended Thin Profile Unit Cooler
Models LTA, LTL unit coolers are the most compact designed unit for reach-in display
cases. The unit’s low height design allows the unit to ‘hide’ at the top of the cooler, giving
the case a cleaner look and allows for more room for shelves and product. These units have
front-access end panels for easy access to refrigerant and electrical compartments, along
with modular front-access panels that make it easy to access the motors. Internally enhanced
tube design provides increased unit performance.
Better performance, easy installation, servicing and the quality of Chandler makes this unit
the perfect fit for your display case needs.
Capacity
(BTUH)
LTA
Model
Fan
Motor (Total FLA)
10°F TD* Qty. CFM
HP
LTA053
LTA079
LTA102
LTA134
LTA172
5,300
7,900
10,200
13,400
17,200
2
3
4
5
6
850
1,350
1,800
2,250
2,550
1/20
1/20
1/20
1/20
1/20
LTL046BA
LTL068BA
LTL093BA
LTL115BA
LTL133BA
4,600
6,800
9,300
11,500
13,300
2
3
4
5
6
850
1,300
1,700
2,100
2,550
1/20
1/20
1/20
1/20
1/20
Defrost Heater
Dimensions (in.)
Shaded Pole
208-230/1/60
L
208115/1/60
Watts Amps
230/1/60
LTA Air Defrost
3.6
2.0
–
–
49-3/8
5.4
3.0
–
–
69-1/8
7.2
4.0
–
–
88-7/8
9.0
5.0
–
–
108-5/8
10.8
6.0
–
–
128-3/8
LTL Electric Defrost
–
2.0
1,100
4.8
49.50
–
3.0
1,650
7.2
69.25
–
4.0
2,200
9.6
89.00
–
5.0
2,750
12.0
108.75
–
6.0
3,300
14.4
128.50
Connections (in.)
Approx.
Net Wt.
Coil
External
Suction
Drain (lbs.)
Inlet
Equalizer
ID
MPT
OD
OD
H
D
8-7/8
8-7/8
8-7/8
8-7/8
8-7/8
18-1/8
18-1/8
18-1/8
18-1/8
18-1/8
1/2
1/2
1/2
1/2
1/2
5/8
5/8
7/8
7/8
1-1/8
1/4
1/4
1/4
1/4
1/4
3/4
3/4
3/4
3/4
3/4
48
69
85
108
124
8-7/8
8-7/8
8-7/8
8-7/8
8-7/8
18-1/8
18-1/8
18-1/8
18-1/8
18-1/8
1/2
1/2
1/2
1/2
1/2
5/8
5/8
7/8
7/8
1-1/8
1/4
1/4
1/4
1/4
1/4
3/4
3/4
3/4
3/4
3/4
48
69
85
108
124
*+25 SST Air, -10 SST Electric
Low Profile Air Defrost Unit Coolers
Model RLC low profile, air defrost unit coolers are designed for maximum capacity with
minimum headroom, space and energy. These units are suitable for use with R-22, R-507, or R404A. The units are only 15" high and are designed to mount flush with top of the cooler. The RLC
cabinet design features easy front access to electrical and refrigeration components. RLC units also
feature extended model and capacity offering to better match with Chandler condensing units.
Advancements include standard plastic fan guard design with optional wire guards; front-facing
electric board for easy access and optimized space in end panels. Improved drain pan design.
Motor harness and solenoid harness are easier to access from the bottom of the coil. Solenoid
harness come standard. Available with PSC and EC motor options.
RLC
Model
RLC040
RLC052
RLC065
RLC070
RLC090
RLC104
RLC120
RLC130
RLC140
RLC156
RLC180
RLC208
RLC260
RLC312
RLC370
1
Capacty
(BTUH)
Fan
10°F TD
+25 SST
Qty.
CFM
4,000
5,200
6,500
7,000
9,000
10,400
12,000
13,000
14,000
15,600
18,000
20,800
26,000
31,200
37,000
1
1
1
2
2
2
2
2
3
3
3
4
5
6
6
730
700
650
1,460
1,400
1,400
1,300
1,300
2,100
2,100
1,950
2,800
3,250
3,900
3,900
Motor (Total FLA)
Shaded Pole
PSC, PSC-TE
EC
L
208208208115/1/60
115/1/60
460/1/60 115/1/60
230/1/60
230/1/60
230/1/60
1.8
1.0
1.0
0.5
0.4
0.9
0.5
29-1/2
1.8
1.0
1.0
0.5
0.4
0.9
0.5
29-1/2
1.8
1.0
1.0
0.5
0.4
0.9
0.5
29-1/2
3.6
2.0
2.0
1.0
0.8
1.8
1.0
45-1/2
3.6
2.0
2.0
1.0
0.8
1.8
1.0
45-1/2
3.6
2.0
2.0
1.0
0.8
1.8
1.0
45-1/2
3.6
2.0
2.0
1.0
0.8
1.8
1.0
45-1/2
3.6
2.0
2.0
1.0
0.8
1.8
1.0
45-1/2
5.4
3.0
3.0
1.5
1.2
2.7
1.5
61-1/2
5.4
3.0
3.0
1.5
1.2
2.7
1.5
61-1/2
5.4
3.0
3.0
1.5
1.2
2.7
1.5
61-1/2
7.2
4.0
4.0
2.0
1.6
3.6
2.0
77-1/2
9.0
5.0
5.0
2.5
2.0
4.5
2.5
93-1/2
10.8
6.0
6.0
3.0
2.4
5.4
3.0
109-1/2
10.8
6.0
6.0
3.0
2.4
5.4
3.0
109-1/2
Drain MPT 3/4" for all air defrost models
6
Dimensions1 (in.) Connections (in.)
H
D
Inlet
OD
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
Suction
ID
5/8
5/8
7/8
7/8
7/8
7/8
7/8
7/8
7/8
7/8
7/8
1-1/8
1-1/8
1-1/8
1-3/8
Approx.
Net Wt.
(lbs.)
28
31
34
45
48
49
51
53
63
67
69
82
103
124
127
Low Profile Electric Defrost Unit Coolers
Models ELC/EFC low profile, electric defrost unit coolers offer the same features as the air defrost models above and are available in 6 or
4 fins per inch models.
Capacty
Fan
(BTUH)
ELC/
EFC
10°F TD
Model
Qty. CFM
-20 SST
Motor (Total FLA)
Shaded
Pole
208230/1/60
208230/1/60
PSC, PSC-TE
ELC035
ELC040
ELC047
ELC065
ELC075
ELC090
ELC120
ELC140
ELC160
ELC180
ELC200
ELC240
ELC280
3,500
4,000
4,700
6,500
7,500
9,000
12,000
14,000
16,000
18,000
20,000
24,000
28,000
1
1
1
2
2
2
3
3
4
4
5
6
6
700
700
650
1,400
1,300
1,300
2,100
1,950
2,600
2,600
3,250
3,900
3,900
1.0
1.0
1.0
2.0
2.0
2.0
3.0
3.0
4.0
4.0
5.0
6.0
6.0
0.5
0.5
0.5
1.0
1.0
1.0
1.5
1.5
2.0
2.0
2.5
3.0
3.0
EFC041
EFC068
EFC080
EFC102
EFC136
EFC170
EFC204
EFC235
4,100
6,800
8,000
10,200
13,600
17,000
20,400
23,500
1
2
2
3
4
5
6
6
690
1,380
1,380
2,170
2,760
3,450
4,140
4,140
1.0
2.0
2.0
3.0
4.0
5.0
6.0
6.0
0.5
1.0
1.0
1.5
2.0
2.5
3.0
3.0
Defrost Heater (amps) Dimensions1 (in.)
EC
208230/1
208230/1/60
ELC Models 6 Fins Per Inch
0.4
0.5
3.9
0.4
0.5
3.9
0.4
0.5
3.9
0.8
1.0
7.8
0.8
1.0
7.8
0.8
1.0
7.8
1.2
1.5
11.7
1.2
1.5
11.7
1.6
2.0
15.7
1.6
2.0
15.7
2.0
2.5
19.6
2.4
3.0
23.5
2.4
3.0
23.5
EFC Models 4 Fins Per Inch
0.4
0.5
3.9
0.8
1.0
7.8
0.8
1.0
7.8
1.2
1.5
11.7
1.6
2.0
15.7
2.0
2.5
19.6
2.4
3.0
23.5
2.4
3.0
23.5
460/1/60
Connections
(in.)
Approx.
Net Wt.
Suction
(lbs.)
ID
208230/1
460/1
L
H
D
Inlet
OD
2.3
2.3
2.3
4.5
4.5
4.5
6.8
6.8
9.0
9.0
11.3
13.6
13.6
2.0
2.0
2.0
3.9
3.9
3.9
5.9
5.9
7.8
7.8
9.8
11.7
11.7
29-1/2
29-1/2
29-1/2
45-1/2
45-1/2
45-1/2
61-1/2
61-1/2
77-1/2
77-1/2
93-1/2
109-1/2
109-1/2
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
5/8
5/8
5/8
5/8
7/8
7/8
7/8
7/8
1-1/8
1-1/8
1-1/8
1-1/8
1-1/8
24
26
29
43
45
48
60
62
81
84
101
121
124
2.3
4.5
4.5
6.8
9.0
11.3
13.6
13.6
2.0
3.9
3.9
5.9
7.8
9.8
11.7
11.7
29-1/2
45-1/2
45-1/2
61-1/2
77-1/2
93-1/2
109-1/2
109-1/2
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
5/8
7/8
7/8
7/8
1-1/8
1-1/8
1-1/8
1-1/8
28
44
47
59
80
100
120
123
Low Profile Hot Gas Defrost Unit Coolers
Model GLC low profile, hot gas defrost unit coolers offer the same features as the air defrost models above and are available in 6 or 4 fins
per inch models.
GLC
Model
Capacty
(BTUH)
10°F TD
-20 SST
Fan
Motor (Total FLA)
Shaded Pole
Qty. CFM
PSC, PSC-TE
208115/1/60
115/1/60
230/1/60
GLC035
GLC040
GLC047
GLC065
GLC075
GLC090
GLC120
GLC140
GLC160
GLC180
GLC200
GLC240
GLC280
3,500
4,000
4,700
6,500
7,500
9,000
12,000
14,000
16,000
18,000
20,000
24,000
28,000
1
1
1
2
2
2
3
3
4
4
5
6
6
700
700
650
1,400
1,300
1,300
2,100
1,950
2,600
2,600
3,250
3,900
3,900
1.8
1.8
1.8
3.6
3.6
3.6
5.4
5.4
7.2
7.2
9.0
10.8
10.8
1.0
1.0
1.0
2.0
2.0
2.0
3.0
3.0
4.0
4.0
5.0
6.0
6.0
1.0
1.0
1.0
2.0
2.0
2.0
3.0
3.0
4.0
4.0
5.0
6.0
6.0
GLC041
GLC068
GLC080
GLC102
GLC136
GLC170
GLC204
GLC235
4,100
6,800
8,000
10,200
13,600
17,000
20,400
23,500
1
2
2
3
4
5
6
6
690
1,380
1,380
2,170
2,760
3,450
4,140
4,140
1.8
3.6
3.6
5.4
7.2
9.0
10.8
10.8
1.0
2.0
2.0
3.0
4.0
5.0
6.0
6.0
1.0
2.0
2.0
3.0
4.0
5.0
6.0
6.0
Dimensions1 (in.)
EC
208460/1/60 115/1/60
230/1/60
GLC Models 6 Fins Per Inch
0.5
0.4
1.1
0.5
0.4
1.1
0.5
0.4
1.1
1.0
0.8
2.0
1.0
0.8
2.0
1.0
0.8
2.0
1.5
1.2
2.9
1.5
1.2
2.9
2.0
1.6
3.8
2.0
1.6
3.8
2.5
2.0
4.7
3.0
2.4
5.6
3.0
2.4
5.6
GLC Models 4 Fins Per Inch
0.5
0.4
1.1
1.0
0.8
2.0
1.0
0.8
2.0
1.5
1.2
2.9
2.0
1.6
3.8
2.5
2.0
4.7
3.0
2.4
5.6
3.0
2.4
5.6
Drain MPT 3/4" for all electric and hot gas defrost models. Side Port OD 3/8" and Hot
Gas Pan Connection 5/8" for all hot gas defrost models.
Connections
(in.)
Inlet
Approx.
Suction Net Wt.
(lbs.)
ID
208230/1/60
L
H
D
0.6
0.6
0.6
1.1
1.1
1.1
1.6
1.6
2.1
2.1
2.6
3.1
3.1
29-1/2
29-1/2
29-1/2
45-1/2
45-1/2
45-1/2
61-1/2
61-1/2
77-1/2
77-1/2
93-1/2
109-1/2
109-1/2
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
5/8
5/8
5/8
5/8
7/8
7/8
7/8
7/8
7/8
1-1/8
1-1/8
1-1/8
1-1/8
5/8
5/8
5/8
5/8
7/8
7/8
7/8
7/8
1-1/8
1-1/8
1-1/8
1-1/8
1-1/8
26
28
31
45
47
50
62
64
83
86
103
123
126
0.6
1.1
1.1
1.6
2.1
2.6
3.1
3.1
29-1/2
45-1/2
45-1/2
61-1/2
77-1/2
93-1/2
109-1/2
109-1/2
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
5/8
5/8
5/8
7/8
7/8
7/8
7/8
1-1/8
5/8
7/8
7/8
7/8
1-1/8
1-1/8
1-1/8
1-1/8
30
46
49
61
82
102
122
125
ODF
1
7
Low Flow Low Velocity Air Defrost Unit Coolers
Model LAH are ideal for meat storage and preparation rooms, floral coolers, dough retarding
and many other applications requiring low air velocities and low sound levels. With low
velocity unit coolers, high humidities can be maintained to minimize product shrinkage
and dehydration. These units are ideal for any type of workroom where human comfort is
important.
With a low, narrow construction and strong aluminum hanger bars, Low Flow Low Velocity is
perfect for use in between rail beams in meat storage and aging rooms and is easy to install.
Model LAH has been designed for the attractive appearance and easy cleaning necessary in
food processing. A double drain pan system eliminates sweating problems, and the rust-free,
all-aluminum white case ensures the long-lasting professional look needed in customer areas
or work rooms. Available with PSC and EC motor options.
LAH
Model
LAH070
LAH090
LAH120
LAH130
LAH160
LAH170
LAH190
LAH220
LAH270
Capacity
(BTUH)*
10°F
TD
7,000
8,700
11,800
12,500
15,000
16,500
18,900
22,500
26,600
Fan
15°F
Qty. CFM
TD
10,500
13,050
17,700
18,750
22,500
24,750
28,350
33,750
39,900
2
2
2
2
2
2
2
2
2
1,200
1,200
1,300
1,300
1,900
1,900
2,400
2,700
3,200
Motor (Total FLA)
Dimensions (in.) Connections (in.)
Approx.
Shaded Pole
PSC
EC
Net Wt.
Liq. Suct. Drain
(lbs.)
L
H
D
208208208OD OD NPS
115/1/60
115/1/60
460/1/60 115/1/60
230/1/60
230/1/60
230/1/60
3.6
2.4
1.24
0.82
–
1.8
1.0
83
14
23-1/4 1/2 7/8
3/4
178
3.6
2.4
1.24
0.82
–
1.8
1.0
83
14
23-1/4 1/2 7/8
3/4
189
3.6
2.4
1.24
0.82
–
1.8
1.0
111 14-1/2 23-1/4 1/2 7/8
3/4
262
3.6
2.4
1.24
0.82
–
1.8
1.0
111 14-1/2 23-1/4 1/2 7/8
3/4
264
3.6
2.4
1.24
0.82
–
1.8
1.0
114
16
23-1/4 1/2 1-1/8 3/4
280
3.6
2.4
1.24
0.82
–
1.8
1.0
114
16
23-1/4 1/2 1-1/8 3/4
285
–
–
2.80
1.40
0.8
4.8
2.4
134 16-1/2 23-1/4 1/2 1-1/8 3/4
298
–
–
2.80
1.40
0.8
4.8
2.4
153 16-1/2 23-1/4 1/2 1-1/8 3/4
366
–
–
2.80
1.40
0.8
4.8
2.4
158
20
28-1/4 1/2 1-3/8 3/4
405
Low Flow Low Velocity Electric Defrost Unit Coolers
Model LAL offers the same features as air defrost models and are designed for use from 28°F to 34°F. The high efficiency,
fast electric defrost allows the LAL to maintain room temperature and minimize incidence of sliming and the formation
of bacterial growth.
LAL
Model
LAL070
LAL090
LAL120
LAL130
LAL160
LAL170
LAL190
LAL220
LAL270
Capacity
(BTUH)*
10°F
TD
7,000
8,700
11,800
12,500
15,000
16,500
18,900
22,500
26,600
Fan
15°F
Qty. CFM
TD
10,500
13,050
17,700
18,750
22,500
24,750
28,350
33,750
39,900
2
2
2
2
2
2
2
2
2
1,200
1,200
1,300
1,300
1,900
1,900
2,400
2,700
3,200
Motor (Total FLA)
Shaded Pole
PSC
EC
208208208460/1/60
230/1/60
230/1/60
230/1/60
2.4
0.82
–
1.0
2.4
0.82
–
1.0
2.4
0.82
–
1.0
2.4
0.82
–
1.0
2.4
0.82
–
1.0
2.4
0.82
–
1.0
–
1.40
0.8
4.8
–
1.40
0.8
4.8
–
1.40
0.8
4.8
Defrost Heater
230/1/60
Watts
2,650
2,650
3,850
3,850
3,850
3,850
4,770
5,700
5,700
Connections
(in.)
Dimensions (in.)
Amps
L
H
D
11.5
11.5
16.7
16.7
16.7
16.7
20.7
24.8
24.8
83
83
111
111
114
114
134
153
158
14
14
14-1/2
14-1/2
16
16
16-1/2
16-1/2
20
23-1/4
23-1/4
23-1/4
23-1/4
23-1/4
23-1/4
23-1/4
23-1/4
28-1/4
Liq.
OD
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
Suct.
OD
7/8
7/8
7/8
7/8
1-1/8
1-1/8
1-1/8
1-1/8
1-3/8
Approx.
Net Wt.
Drain (lbs.)
NPS
3/4
178
3/4
189
3/4
262
3/4
264
3/4
280
3/4
285
3/4
298
3/4
366
3/4
405
Low Flow Low Velocity Hot Gas Defrost Unit Coolers
Model LAG offers the same features as air defrost models and are designed for use from 28°F to 34°F. The hot gas
defrost is available factory-installed or as a field installed kit.
Capacity
(BTUH)*
LAG
Model
LAG070
LAG090
LAG120
LAG130
LAG160
LAG170
LAG190
LAG220
LAG270
* +25 SST
8
10°F
TD
7,000
8,700
11,800
12,500
15,000
16,500
18,900
22,500
26,600
Fan
15°F
Qty. CFM
TD
10,500
13,050
17,700
18,750
22,500
24,750
28,350
33,750
39,900
2
2
2
2
2
2
2
2
2
1,200
1,200
1,300
1,300
1,900
1,900
2,400
2,700
3,200
Motor (Total FLA)
Shaded Pole
115/1/60
3.6
3.6
3.6
3.6
3.6
3.6
–
–
–
PSC
Dimensions (in.)
EC
Connections (in.)
Approx.
Net Wt.
Hot
Liq. Suct.
Drain (lbs.)
Gas
NPS
OD OD
OD
L
H
D
208208208115/1/60
460/1/60 115/1/60
230/1/60
230/1/60
230/1/60
2.4
1.24
1.0
–
1.8
1.0
83
14
23-1/4 7/8 7/8
2.4
1.24
1.0
–
1.8
1.0
83
14
23-1/4 7/8 7/8
2.4
1.24
1.0
–
1.8
1.0
111 14-1/2 23-1/4 7/8 7/8
2.4
1.24
1.0
–
1.8
1.0
111 14-1/2 23-1/4 7/8 7/8
2.4
1.24
1.0
–
1.8
1.0
114
16
23-1/4 7/8 1-1/8
2.4
1.24
1.0
–
1.8
1.0
114
16
23-1/4 7/8 1-1/8
–
2.80
1.4
.08
4.8
2.4
134 16-1/2 23-1/4 7/8 1-1/8
–
2.80
1.4
.08
4.8
2.4
153 16-1/2 23-1/4 7/8 1-1/8
–
2.80
1.4
.08
4.8
2.4
158
20
28-1/4 7/8 1-3/8
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
5/8
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
178
189
262
264
280
285
298
366
405
Low Velocity Center Mount Air Defrost Unit Coolers
Model HWA is ideal for floral storage, fresh fruit and vegetables, dough retarding, fresh
meat storage and preparation and many other applications of 35° F and above. The low air
flow and quiet fans are classically suited for work-room applications.
The generous coil surface combined with close TD system balance provides high humidity
characteristics to minimize product shrinkage and drying. Available with PSC and EC
motor options.
HWA
Model
HWA050
HWA075
HWA100
HWA130
HWA155
HWA180
HWA210
HWA270
HWA340
Capacity
Fan
Motor (Total FLA)
(BTUH)*
Shaded Pole
PSC
EC
10°F 15°F
Qty. CFM
TD
TD
115/1/60 230/1/60 115/1/60 230/1/60 115/1/60 230/1/60
5,000 7,500
1
725
2.1
1.1
0.9
0.5
0.9
0.5
7,500 11,250 1
730
2.1
1.1
0.9
0.5
0.9
0.5
10,000 15,000 2 1,450
4.2
2.2
1.8
1.0
1.8
1.0
13,000 19,500 2 1,470
4.2
2.2
1.8
1.0
1.8
1.0
15,500 23,250 2 1,460
4.2
2.2
1.8
1.0
1.8
1.0
18,000 27,000 3 2,130
6.3
3.3
2.7
1.5
2.7
1.5
21,000 31,500 4 2,840
8.4
4.4
3.6
2.0
3.6
2.0
27,000 40,500 4 2,800
8.4
4.4
3.6
2.0
3.6
2.0
34,000 51,000 5 3,500
10.5
5.5
4.5
2.5
4.5
2.5
App.
Net
Liquid Suction Drain Wt.
L
H
D
OD
OD
FPT (lbs.)
53-1/2 8-7/8 26-5/8
1/2
7/8
3/4
70
75-1/2 8-7/8 26-5/8
1/2
7/8
3/4
103
75-1/2 11-3/8 26-5/8
1/2
7/8
3/4
106
75-1/2 15-1/8 26-5/8 1-1/8
1-1/8
3/4
145
75-1/2 15-1/8 26-5/8 1-1/8
1-1/8
3/4
149
75-1/2 15-1/8 26-5/8 1-1/8
1-1/8
3/4
160
97-1/2 15-1/8 26-5/8 1-1/8
1-1/8
3/4
193
97-1/2 15-1/8 26-5/8 1-3/8
1-3/8
3/4
200
119-1/2 15-1/8 26-5/8 1-3/8
1-3/8
3/4
242
Dimensions (in.)
Connections (in.)
Low Velocity Center Mount Electric Defrost Unit Coolers
Model HWE offers the same benefits as the air defrost models above and is ideal for applications of 24° F and above.
HWE
Model
HWE050
HWE075
HWE100
HWE130
HWE155
HWE180
HWE210
HWE270
HWE340
Capacity
Fan
(BTUH)*
10°F 15°F
Qty. CFM
TD
TD
5,000 7,500
1
725
7,500 11,250 1
730
10,000 15,000 2 1,450
13,000 19,500 2 1,470
15,500 23,250 2 1,460
18,000 27,000 3 2,130
21,000 31,500 4 2,840
27,000 40,500 4 2,800
34,000 51,000 5 3,500
Motor (Total FLA)
Shaded Pole
230/1/60
1.1
1.1
2.2
2.2
2.2
3.3
4.4
4.4
5.5
PSC
230/1/60
0.5
0.5
1.0
1.0
1.0
1.5
2.0
2.0
2.5
App.
Net
230/1/60
Liquid Suction Drain Wt.
L
H
D
OD
OD
FPT (lbs.)
Amps
8.7
53-1/2 8-7/8 26-5/8
1/2
7/8
3/4
75
10.5
75-1/2 8-7/8 26-5/8
1/2
7/8
3/4
108
12.2
75-1/2 11-3/8 26-5/8
1/2
7/8
3/4
111
17.4
75-1/2 15-1/8 26-5/8 1-1/8
1-1/8
3/4
150
17.4
75-1/2 15-1/8 26-5/8 1-1/8
1-1/8
3/4
154
17.4
75-1/2 15-1/8 26-5/8 1-1/8
1-1/8
3/4
157
22.6
97-1/2 15-1/8 26-5/8 1-1/8
1-1/8
3/4
203
22.6
97-1/2 15-1/8 26-5/8 1-3/8
1-3/8
3/4
208
30.4
119-1/2 15-1/8 26-5/8 1-3/8
1-3/8
3/4
250
Defrost Heater
EC
230/1/60
0.5
0.5
1.0
1.0
1.0
1.5
2.0
2.0
2.5
Watts
2,000
2,400
2,800
4,000
4,000
4,000
5,200
5,200
7,000
Dimensions (in.)
Connections (in.)
Low Velocity Center Mount Hot Gas Defrost Unit Coolers
Model HWG offers the same benefits as the air defrost models above and is ideal for applications of 24° F and above.
HWG
Model
HWG100
HWG130
HWG155
HWG180
HWG210
HWG270
HWG340
Capacity
(BTUH)*
10°F
TD
15°F
TD
10,000
13,000
15,500
18,000
21,000
27,000
34,000
15,000
19,500
23,250
27,000
31,500
40,500
51,000
Fan
Motor (Total FLA)
Shaded Pole
Qty. CFM
2
2
2
3
4
4
5
1,450
1,470
1,460
2,130
2,840
2,800
3,500
2.2
2.2
2.2
3.3
4.4
4.4
5.5
1.8
1.8
1.8
2.7
3.6
3.6
4.5
EC
115/1 230/1
208208- Watts
115/1/60
Amps
230/1/60
230/1/60
1.0
1.8
1.0
350 3.0
1.5
1.0
1.8
1.0
500 4.4
2.2
1.0
1.8
1.0
500 4.4
2.2
1.5
2.7
1.5
500 4.4
2.2
2.0
3.6
2.0
650 5.7
2.8
2.0
3.6
2.0
650 5.7
2.8
2.5
4.5
2.5
875 7.6
3.8
Dimensions (in.)
PSC
115/1/60 230/1/60 115/1/60
4.2
4.2
4.2
6.3
8.4
8.4
10.5
Drain Pan Heater
L
H
D
75-1/2
75-1/2
75-1/2
75-1/2
97-1/2
97-1/2
119-1/2
11-3/8
15-1/8
15-1/8
15-1/8
15-1/8
15-1/8
15-1/8
26-5/8
26-5/8
26-5/8
26-5/8
26-5/8
26-5/8
26-5/8
Connections (in.)1 App.
Net
Liq. Suct. Side Wt.
OD OD Port (lbs.)
1/2
1-1/8
1-1/8
1-1/8
1-1/8
1-1/8
1-1/8
7/8
1-1/8
1-1/8
1-1/8
1-1/8
1-3/8
1-3/8
1/2
5/8
5/8
5/8
5/8
7/8
7/8
131
170
174
185
223
228
270
* +25 SST
1
Drain FPT 3/4" for all models
9
Center Mount Air Defrost Unit Coolers
Model TLH units are compact, medium velocity coolers designed for use in 35° F and above
rooms. The low height gives more head room and allows product to be stacked higher. The center
ceiling mount with dual air flow allows shelving and storage of product around all walls.
Equipped with dual drain pans to prevent sweating, the TLH units have a heavy gauge
grained-aluminum cabinet that cleans easily and looks attractive. The stainless steel screws
prevent rust streaks and PVC coated fan guards won’t rust or rattle.
Ease of installation and service are also part of the design. End panels can be removed quickly
to access refrigerant components and electrical terminal block, without the need to drop the
fan panel/drain pan. A quick-disconnect, waterproof plug and receptacle is supplied with
each motor. Available with PSC and EC motor options.
TLH
Model
TLH052
TLH076
TLH090
TLH102
TLH108
TLH134
TLH156
TLH179
TLH208
TLH249
Capacity
(BTUH)
Fan
Motor (Total FLA)
Shaded Pole
PSC
10°F TD
Qty. CFM
+25 SST
115/1/60 230/1/60 115/1/60
5,200
7,600
9,000
10,200
10,800
13,400
15,600
17,900
20,800
24,900
1
2
2
2
3
3
3
4
4
5
610
1,300
1,260
1,220
1,950
1,890
1,830
2,520
2,440
3,050
2.1
4.2
4.2
4.2
6.3
6.3
6.3
8.4
8.4
10.5
1.1
2.2
2.2
2.2
3.3
3.3
3.3
4.4
4.4
5.5
Dimensions (in.)
0.9
1.8
1.8
1.8
2.7
2.7
2.7
3.6
3.6
4.5
EC
L
208208115/1/60
230/1/60
230/1/60
0.5
0.9
0.5
31-1/2
1.0
1.8
1.0
53-1/2
1.0
1.8
1.0
53-1/2
1.0
1.8
1.0
53-1/2
1.5
2.7
1.5
75-1/2
1.5
2.7
1.5
75-1/2
1.5
2.7
1.5
75-1/2
2.0
3.6
2.0
97-1/2
2.0
3.6
2.0
97-1/2
2.5
4.5
2.5
119-1/2
Connections1 (in.)
H
D
Liquid
OD
8-5/8
8-5/8
8-5/8
8-5/8
8-5/8
8-5/8
8-5/8
8-5/8
8-5/8
8-5/8
28-13/16
28-13/16
28-13/16
28-13/16
28-13/16
28-13/16
28-13/16
28-13/16
28-13/16
28-13/16
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
Approx.
Net Wt.
Suction
(lbs.)
OD
7/8
7/8
7/8
7/8
7/8
7/8
7/8
7/8
1-1/8
1-1/8
42
64
70
83
105
117
123
149
164
206
Center Mount Electric Defrost Unit Coolers
Model TLL units offer the same great benefits as air defrost, but have defrost controls mounted and wired to a terminal
board and are designed for –20° F to 34° F applications.
Capacity (BTUH)
Fan
Motor (Total FLA)
Shaded Pole
PSC
EC
TLL
10°F TD 12°F
Model
Qty. CFM
208208-20 SST
TD
208-230/1
230/1/60 230/1/60
TLL040 4,000
4,800
1
610
1.1
0.5
0.5
TLL054 5,400
6,480
2 1,300
2.2
1.0
1.0
TLL065 6,500
7,800
2 1,260
2.2
1.0
1.0
TLL090 9,000
10,800
3 1,950
3.3
1.5
1.5
TLL130 13,000 15,600
3 1,830
3.3
1.5
1.5
TLL174 17,400 20,880
4 2,440
4.4
2.0
2.0
Defrost Heater
Dimensions (in.)
Connections1 (in.)
Watts
Amps
L
H
D
Inlet
OD
Suction
OD
Approx.
Net Wt.
(lbs.)
1,200
2,000
2,000
2,400
3,600
4,800
5.3
8.7
8.7
10.5
15.7
20.9
31-1/2
53-1/2
53-1/2
75-1/2
75-1/2
97-1/2
8-5/8
8-5/8
8-5/8
8-5/8
8-5/8
8-5/8
28-13/16
28-13/16
28-13/16
28-13/16
28-13/16
28-13/16
1/2
1/2
1/2
1/2
1/2
1/2
7/8
7/8
7/8
7/8
7/8
1-1/8
90
120
120
160
174
218
Medium Profile Unit Coolers
Models HMA engineered superior quality and performance into the new
medium profile unit coolers. With features like the innovative Thermo-Flex™
coil design that carries a five-year limited warranty against refrigerant leaks,
internal grooved tubing for greater heat transfer efficiency and motors that
plug into the wiring harness for easier accessibility, these units provide
long life and dependability to your refrigeration application.
Capacity
Fan
Motor (Total FLA)
Dimensions (in.)
Connections1 (in.) App.
(BTUH)
Net Wt.
PSC
EC
10°F TD
Inlet
Suct.
(lbs.)
Qty. CFM
L
H
D
+25 SST
ODF
ODF
115/1/60
230/1/60
460/1660
115/1/60 208-230/1/60
HMA130 13,000
1
2,300
4.0
1.8
1.0
2.8
1.4
39-5/16 25 22-7/8
1/2
7/8
115
HMA155 15,500
1
2,200
4.0
1.8
1.0
2.8
1.4
39-5/16 25 22-7/8
1/2
1-1/8
123
HMA245 24,500
2
4,600
8.0
3.6
2.0
5.6
2.8
67-5/16 25 22-7/8
7/8
1-1/8
134
HMA300 30,000
2
4,400
8.0
3.6
2.0
5.6
2.8
67-5/16 25 22-7/8
7/8
1-1/8
148
HMA365 36,500
3
6,900
12.0
5.4
3.0
8.4
4.2
95-5/16 25 22-7/8
7/8
1-3/8
200
HMA450 45,000
3
6,600
12.0
5.4
3.0
8.4
4.2
95-5/16 25 22-7/8 1-1/8†
1-3/8
227
HMA510 51,000
4
9,200
16.0
7.2
4.0
11.2
5.6
123-5/16 25 22-7/8 1-1/8†
1-5/8
230
HMA600 60,000
4
8,800
16.0
7.2
4.0
11.2
5.6
123-5/16 25 22-7/8 1-1/8†
1-5/8
255
HMA710 71,000
5
10,500
9.0
5.0
14.0
7.0
138-13/16 25 22-7/8 1-1/8†
1-5/8
285
1
All HMA coils have 1/4" OD external equalizer and 3/4" Drain FPT connections. † Supplied with adapter to 7/8 ODF.
HMA
Model
10
Medium Profile Electric Defrost Unit Coolers
Models HME/HML offer the same great features as air defrost models and are available in 6 or 4 fins per inch ranging in size
from 10,000 to 62,000 BTUH.
HME/
HML
Model
HME101
HME140
HME190
HME260
HME310
HME390
HME430
HME520
HME620
HML100
HML165
HML220
HML250
HML330
HML370
HML440
HML530
Capacity
(BTUH)
Fan
Motor (Total FLA)
Defrost Heater (amps)
PSC
EC
10°F TD
208208Qty. CFM
208- 460/1/60 575/1/60 208230/3/60
-20 SST
230/1/60
230/1/60 Watts 230/1/60
HME Models 6 Fins Per Inch
10,100
1 2,350
1.8
1.0
0.75
1.4
2,730
11.9
8.2
14,000
1 2,250
1.8
1.0
0.75
1.4
2,730
11.9
8.2
19,000
2 4,700
3.6
2.0
1.50
2.8
5,350
23.3
16.0
26,000
2 4,500
3.6
2.0
1.50
2.8
5,350
23.3
16.0
31,000
3 7,050
5.4
3.0
2.25
4.2
7,750
33.7
23.2
39,000
3 6,750
5.4
3.0
2.25
4.2
7,750
33.7
23.2
43,000
4 8,800
7.2
4.0
3.00
5.6
10,200
–
30.5
52,000
4 8,400
7.2
4.0
3.00
5.6
10,200
–
30.5
62,000
5 10,000
9.0
5.0
3.75
7.0
11,600
–
34.7
HML Models 4 Fins Per Inch
10,000
1 2,350
1.8
1.0
0.75
1.4
2,730
11.9
8.2
16,500
2 4,900
3.6
2.0
0.75
2.8
5,350
23.3
16.0
22,000
2 4,650
3.6
2.0
1.50
2.8
5,350
23.3
16.0
25,000
3 7,350
5.4
3.0
1.50
4.2
7,750
33.7
23.2
33,000
3 6,975
5.5
3.0
2.25
4.2
7,750
33.7
23.2
37,000
4 9,100
7.2
4.0
2.25
5.6
10,200
–
30.5
44,000
4 8,700
7.2
4.0
3.00
5.6
10,200
–
30.5
53,000
5 10,350
9.0
5.0
3.00
7.0
11,600
–
34.7
Dimensions (in.)
Connections1
App.
(in.)
Net
Inlet Suct. Wt.
ODF ODF (lbs.)
460/
1/60
460/
3/60
L
H
D
5.9
5.9
11.6
11.6
16.8
16.8
22.2
22.2
25.2
4.1
4.1
8.3
8.3
12.0
12.0
15.8
15.8
18.1
39-5/16
39-5/16
67-5/16
67-5/16
95-5/16
95-5/16
123-5/16
123-5/16
138-5/16
24
24
24
24
24
24
24
24
24
22-3/4
22-3/4
22-3/4
22-3/4
22-3/4
22-3/4
22-3/4
22-3/4
22-3/4
1/2
1/2
7/8
1-1/8†
1-1/8†
1-1/8†
1-1/8†
1-1/8†
1-1/8†
7/8
7/8
1-1/8
1-3/8
1-3/8
1-3/8
1-5/8
1-5/8
1-5/8
118
126
138
153
210
237
267
300
338
5.9
11.6
11.6
16.8
16.8
22.2
22.2
25.2
4.1 39-13/16 24 22-3/4
8.3 67-13/16 24 22-3/4
8.3 67-13/16 24 22-3/4
12.0 95-13/16 24 22-3/4
12.0 95-13/16 24 22-3/4
15.8 123-13/16 24 22-3/4
15.8 123-13/16 24 22-3/4
18.1 138-13/16 24 22-3/4
1/2
7/8
1-1/8†
1-1/8†
1-1/8†
1-1/8†
1-1/8†
1-1/8†
7/8
1-1/8
1-3/8
1-3/8
1-3/8
1-5/8
1-5/8
1-5/8
125
136
151
207
234
262
295
332
Medium Profile Hot Gas Defrost Unit Coolers
Models HMG/HMF offer the same great features as air defrost models and are available in 6 or 4 fins per inch ranging in size
from 16,500 to 52,000 BTUH.
HMG/
HMF
Model
Capacity
(BTUH)
Fan
10°F TD
Qty. CFM
-20 SST
Motor (Total FLA)
115/
1/60
PSC
230/
460/
1/60
1/60
575/
1/60
HMG190
HMG260
HMG310
HMG390
HMG430
HMG520
19,000
26,000
31,000
39,000
43,000
52,000
2
2
3
3
4
4
4,700
4,500
7,050
6,750
8,800
8,400
8.0
8.0
12.0
12.0
16.0
16.0
3.6
3.6
5.4
5.4
7.2
7.2
2.0
2.0
3.0
3.0
4.0
4.0
0.75
0.75
1.50
1.50
2.25
2.25
HMF165
HMF220
HMF250
HMF330
HMF370
HMF440
16,500
22,000
25,000
33,000
37,000
44,000
2
2
3
3
4
4
4,900
4,650
7,350
6,975
9,100
8,700
8.0
8.0
12.0
12.0
16.0
16.0
3.6
3.6
5.4
5.4
7.2
7.2
2.0
2.0
3.0
3.0
4.0
4.0
0.75
0.75
1.50
1.50
2.25
2.25
Defrost Heater (amps)
Dimensions (in.)
EC
115/
208460/
Watts
L
H
115/
2081/60 230/1/60 1/60
1/60 230/1/60
HMG Models 6 Fins Per Inch
5.6
2.8
950
8.3
4.1
2.1
67-5/16 24
5.6
2.8
950
8.3
4.1
2.1
67-5/16 24
8.4
4.2
1,350 11.7
5.9
2.9
95-5/16 24
8.4
4.2
1,350 11.7
5.9
2.9
95-5/16 24
11.2
5.6
1,800 15.7
7.8
3.9 123-5/16 24
11.2
5.6
1,800 15.7
7.8
3.9 123-5/16 24
HMF Models 4 Fins Per Inch
5.6
2.8
950
8.3
4.1
2.1 67-13/16 24
5.6
2.8
950
8.3
4.1
2.1 67-13/16 24
8.4
4.2
1,350 11.7
5.9
2.9 95-13/16 24
8.4
4.2
1,350 11.7
5.9
2.9 95-13/16 24
11.2
5.6
1,800 15.7
7.8
3.9 123-13/16 24
11.2
5.6
1,800 15.7
7.8
3.9 123-13/16 24
D
Connections1
App.
(in.)
Net
Inlet Suct. Wt.
ODF ODF (lbs.)
22-3/4
22-3/4
22-3/4
22-3/4
22-3/4
22-3/4
1-1/8†
1-1/8†
1-1/8†
1-1/8†
1-1/8†
1-1/8†
1-1/8
1-3/8
1-3/8
1-3/8
1-5/8
1-5/8
175
190
210
237
267
300
22-3/4
22-3/4
22-3/4
22-3/4
22-3/4
22-3/4
1-1/8†
1-1/8†
1-1/8†
1-1/8†
1-1/8†
1-1/8†
1-1/8
1-3/8
1-3/8
1-3/8
1-5/8
1-5/8
173
188
207
234
262
295
All HME, HML, HMG and HMF models have 1/4" OD external equalizer and 3/4" Drain FPT connections.
All HMG and HMF models have 5/8" Side Port ODF and 7/8" Hot Gas Pan ODF connections.
1
†
Supplied with adapter to 7/8 ODF
11
Large Unit Coolers Air Defrost
Model HHA large air defrost unit coolers are ideal for warehouse cooler applications. With
a wide capacity range and the patented Thermo-Flex™ coil design, these large unit coolers
provide efficient, reliable operation. Features include a mill finish aluminum cabinet, 850 RPM
motors for low noise and high reliability, liquid line solenoid wiring harness for faster installation,
Schrader fitting for easier suction temperature measurement. Also, the large unit coolers have
captive fasteners on access panels for easy servicing — no fumbling with loose bolts and nuts.
The HHA Series also has a standardized terminal board for easier field wiring.
Options include high CFM motor and fan combinations, totally enclosed motors, low temp
motors for blast cooling, long air throw collars for large Warehouse/Industrial applications
and insulated drain pans. PSC motors come standard to help you save energy.
HHA
Model
HHA520
HHA630
HHA750
HHA850
HHA930
HHA1100
HHA1170
HHA1400
HHA1610
HHA1900
HHA2200
HHA2440
HHA2160*
HHA2500*
HHA2780*
Capacity
(BTUH)
Fan
10°F TD
Qty.
+25 SST
52,000
63,000
75,000
85,000
93,000
110,000
117,000
140,000
161,000
190,000
220,000
244,000
216,000
250,000
278,000
2
2
3
3
4
4
3
3
3
3
4
4
3
4
4
CFM
9,000
9,000
12,600
12,600
16,800
16,800
20,700
20,700
24,300
26,550
30,400
35,400
25,950
29,600
34,600
Motor (Total FLA)
208-230/1/60
460/1/60
Dia.
208(in.) Wired Wired 230/3/60 Wired Wired
1 ph. 3 ph.
1 ph. 3 ph.
24
6.4
5.2
3.4
24
6.4
5.2
3.4
24
9.6
5.5
7.8
3.0
24
9.6
5.5
7.8
3.0
24
12.8
8.7
10.4
4.7
24
12.8
8.7
10.4
4.7
30
13.8
30
13.8
30
19.8
30
21.0
30
26.4
30
28.0
30
21.0
30
26.4
30
28.0
-
Dimensions (in.)
Connections (in.)1
460/
3/60
L
H
D
2.6
2.6
3.9
3.9
5.2
5.2
6.9
6.9
9.9
10.5
13.2
14.0
10.5
13.2
14.0
83-3/32
83-3/32
105-5/32
105-5/32
135-7/32
135-7/32
135-13/32
135-13/32
135-13/32
142-1/2
185-1/2
185-1/2
142-1/2
185-1/2
185-1/2
40-11/32
40-11/32
40-11/32
40-11/32
40-11/32
40-11/32
50-5/16
50-5/16
55-13/16
55-13/16
50-5/16
56-1/4
55-13/16
50-5/16
56-1/4
29-1/2
29-1/2
29-1/2
29-1/2
29-1/2
29-1/2
41-3/32
41-3/32
41-3/32
41-3/32
41-3/32
41-3/32
41-3/32
41-3/32
41-3/32
Approx.
Coil
Ext. Net Wt.
Suction
Inlet
Equal. (lbs.)
ODF
ODF
ODF
1-1/8 1-5/8
1/4
270
1-1/8 1-5/8
1/4
300
1-3/8 2-1/8
1/4
390
1-3/8 2-1/8
1/4
430
1-3/8 2-1/8
1/4
515
1-3/8 2-1/8
1/4
565
1-3/8 2-1/8
1/4
738
1-5/8 2-1/8
1/4
800
1-3/8† 2-1/8†
1/4†
850
1-3/8 2-5/8
1/4
1,160
1-3/8 2-5/8
1/4
1,500
1-5/8 2-5/8
1/4
1,600
1-3/8 2-5/8
1/4
1,160
1-3/8 2-5/8
1/4
1,500
1-3/8 2-5/8
1/4
1,600
Large Unit Coolers Electric Defrost
Models HHE/HHL offer the same benefits as air defrost and are ideal for warehouse cooler/freezer applications.
Capacity
(BTUH)
Fan
HHE/HHL
Model 10°F TD
Qty.
-20 SST
CFM
Motor (Total FLA)
208-230/60
460/1/60
Dia.
208(in.) Wired Wired 230/3/60 Wired Wired
1 ph. 3 ph.
1 ph. 3 ph.
HHE450
HHE550
HHE640
HHE740
HHE810
HHE950
HHE1020
HHE1200
HHE1390
HHE1650
HHE2120
45,000
55,000
64,000
74,000
81,000
95,000
102,000
120,000
139,000
165,000
212,000
2
2
3
3
4
4
3
3
3
3
4
9,000
9,000
12,600
12,600
16,800
16,800
20,700
20,700
24,300
26,550
35,400
24
24
24
24
24
24
30
30
30
30
30
6.4
6.4
-
5.5
5.5
8.7
8.7
-
5.2
5.2
7.8
7.8
10.4
10.4
13.8
13.8
19.8
21.0
28.0
HHL400
HHL480
HHL560
HHL650
HHL710
HHL840
HHL890
HHL1050
HHL1220
HHL1440
HHL1860
40,000
48,000
56,000
65,000
71,000
84,000
89,000
105,000
122,000
144,000
186,000
2
2
3
3
4
4
3
3
3
3
4
9,400
9,400
13,200
13,200
17,600
17,600
21,600
21,600
25,200
27,600
36,800
24
24
24
24
24
24
30
30
30
30
30
6.4
6.4
-
5.5
5.5
8.7
8.7
-
5.2
5.2
7.8
7.8
10.4
10.4
13.8
13.8
19.8
21.0
28.0
460/
3/60
L
HHE Models 6 Fins Per Inch
3.4
2.6
83-3/32
3.4
2.6
83-3/32
3.0
3.9
105-5/32
3.0
3.9
105-5/32
4.7
5.2
135-7/32
4.7
5.2
135-7/32
6.9
135-13/32
6.9
135-13/32
9.9
135-13/32
10.5
142-1/2
14.0
185-1/2
HHL Models 4 Fins Per Inch
3.4
2.6
83-3/32
3.4
2.6
83-3/32
3.0
3.9
105-5/32
3.0
3.9
105-5/32
4.7
5.2
135-7/32
4.7
5.2
135-7/32
6.9
135-13/32
6.9
135-13/32
9.9
135-13/32
10.5
142-1/2
14.0
185-1/2
* These models are 8 fins per inch; all other air defrost models are 6 fins per inch.
1
Drain FPT is 1-1/4" for all models. † (2) connections required.
12
Dimensions (in.)
Connections (in.)1
Approx.
Coil
Ext. Net Wt.
Suction
Inlet
Equal. (lbs.)
ODF
ODF
ODF
H
D
40-11/32
40-11/32
40-11/32
40-11/32
40-11/32
40-11/32
50-5/16
50-5/16
55-13/16
55-13/16
56-1/4
29-1/2
29-1/2
29-1/2
29-1/2
29-1/2
29-1/2
41-3/32
41-3/32
41-3/32
41-3/32
41-3/32
1-1/8
1-1/8
1-3/8
1-3/8
1-3/8
1-3/8
1-3/8
1-5/8
1-3/8†
1-3/8
1-5/8
1-5/8
1-5/8
2-1/8
2-1/8
2-1/8
2-1/8
2-1/8
2-1/8
2-1/8†
2-5/8
2-5/8
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4†
1/4
1/4
280
310
405
445
535
585
753
815
865
1,175
1,620
40-11/32
40-11/32
40-11/32
40-11/32
40-11/32
40-11/32
50-5/16
50-5/16
55-13/16
55-13/16
56-1/4
29-1/2
29-1/2
29-1/2
29-1/2
29-1/2
29-1/2
41-3/32
41-3/32
41-3/32
41-3/32
41-3/32
1-1/8
1-1/8
1-3/8
1-3/8
1-3/8
1-3/8
1-3/8
1-5/8
1-3/8†
1-3/8
1-5/8
1-5/8
1-5/8
2-1/8
2-1/8
2-1/8
2-1/8
2-1/8
2-1/8
2-1/8†
2-5/8
2-5/8
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4†
1/4
1/4
277
306
400
440
528
578
744
805
854
1,160
1,600
Large Unit Coolers Hot Gas Defrost
Models HHG/HHF offer the same benefits as air defrost and are ideal for warehouse cooler/freezer applications. Also, optional
field or factory-installed hot gas kits are available.
Capacity
(BTUH)
HHG/
HHF
Model
1
†
Fan
Motor (Total FLA)
208230/1/60
10°F TD
Qty.
-20 SST
CFM
Dimensions (in.)
Connections (in.)1
460/1/60
Dia.
208460/
(in.) Wired Wired 230/3/60 Wired Wired 3/60
1 ph. 3 ph.
L
H
D
1 ph. 3 ph.
HHG450
HHG550
HHG640
HHG740
HHG810
HHG950
HHG1020
HHG1200
HHG1390
HHG1650
HHG2120
45,000
55,000
64,000
74,000
81,000
95,000
102,000
120,000
139,000
165,000
212,000
2
2
3
3
4
4
3
3
3
3
4
9,000
9,000
12,600
12,600
16,800
16,800
20,700
20,700
24,300
26,550
35,400
24
24
24
24
24
24
30
30
30
30
30
6.4
6.4
-
5.5
5.5
8.7
8.7
-
5.2
5.2
7.8
7.8
10.4
10.4
13.8
13.8
19.8
21.0
28.0
HHF400
HHF480
HHF560
HHF650
HHF710
HHF840
HHF890
HHF1050
HHF1220
HHF1440
HHF1860
40,000
48,000
56,000
65,000
71,000
84,000
89,000
105,000
122,000
144,000
186,000
2
2
3
3
4
4
3
3
3
3
4
9,400
9,400
13,200
13,200
17,600
17,600
21,600
21,600
25,200
27,600
36,800
24
24
24
24
24
24
30
30
30
30
30
6.4
6.4
-
5.5
5.5
8.7
8.7
-
5.2
5.2
7.8
7.8
10.4
10.4
13.8
13.8
19.8
21.0
28.0
HHG Models 6 Fins Per Inch
3.4
2.6 83-3/32 40-11/32
3.4
2.6 83-3/32 40-11/32
3.0 3.9 105-5/32 40-11/32
3.0 3.9 105-5/32 40-11/32
4.7 5.2 135-7/32 40-11/32
4.7 5.2 135-7/32 40-11/32
6.9 135-13/32 50-5/16
6.9 135-13/32 50-5/16
9.9 135-13/32 55-13/16
10.5 142-1/2 55-13/16
14.0 185-1/2
56-1/4
HHF Models 4 Fins Per Inch
3.4
2.6 83-3/32 40-11/32
3.4
2.6 83-3/32 40-11/32
3.0 3.9 105-5/32 40-11/32
3.0 3.9 105-5/32 40-11/32
4.7 5.2 135-7/32 40-11/32
4.7 5.2 135-7/32 40-11/32
6.9 135-13/32 50-5/16
6.9 135-13/32 50-5/16
9.9 135-13/32 55-13/16
10.5 142-1/2 55-13/16
14.0 185-1/2
56-1/4
Coil
Inlet
ODF
Hot
Ext.
Suct.
Gas
Equal.
ODF
ODF Side
Port
Hot
Gas
Drain
Pan
Ref
Conn
App.
Net
Wt.
(lbs.)
29-1/2
29-1/2
29-1/2
29-1/2
29-1/2
29-1/2
41-3/32
41-3/32
41-3/32
41-3/32
41-3/32
1-1/8 1-5/8
1-1/8 1-5/8
1-3/8 2-1/8
1-3/8 2-1/8
1-3/8 2-1/8
1-3/8 2-1/8
1-3/8 2-1/8
1-5/8 2-1/8
1-3/8† 2-1/8†
1-3/8† 2-5/8†
1-3/8† 2-5/8†
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4†
1/4†
1/4†
5/8
5/8
7/8
7/8
7/8
7/8
7/8
1-1/8
7/8†
7/8†
7/8†
1-1/8
1-1/8
1-1/8
1-1/8
1-1/8
1-1/8
1-3/8
1-3/8
1-3/8
1-5/8
1-5/8
280
310
405
445
535
585
753
815
865
1,175
1,620
29-1/2
29-1/2
29-1/2
29-1/2
29-1/2
29-1/2
41-3/32
41-3/32
41-3/32
41-3/32
41-3/32
1-1/8 1-5/8
1-1/8 1-5/8
1-3/8 2-1/8
1-3/8 2-1/8
1-3/8 2-1/8
1-3/8 2-1/8
1-3/8 2-1/8
1-5/8 2-1/8
1-3/8† 2-1/8†
1-3/8† 2-5/8†
1-3/8† 2-5/8†
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4†
1/4†
1/4†
5/8
5/8
7/8
7/8
7/8
7/8
7/8
1-1/8
7/8†
7/8†
7/8†
1-1/8
1-1/8
1-1/8
1-1/8
1-1/8
1-1/8
1-3/8
1-3/8
1-3/8
1-5/8
1-5/8
277
306
400
440
528
578
744
805
854
1,160
1,600
Drain FPT is 1-1/4" for all models.
(2) connections required.
What is Thermo-Flex™ coil design?
Chandler’s innovative coil design utilizes a new and unique approach to coil expansion that virtually eliminates the possibility of leaks at
tube sheets and coil supports. Our engineers conceived the design after intense analysis of the cause of common coil failures. Through
the use of accelerated test procedures and computer simulation, our engineers pinpointed the primary stress points of a coil during its
operation.
The Thermo-Flex™ coil design for the evaporator (U.S. Patent No. 5,584,340) allows the coil to ‘flex’ during periods of defrost which
result in expansion of the coil surface. By eliminating the possibility of wear at critical stress areas, the integrity and longevity of the
unit are dramatically increased.
The result is a product which greatly enhances overall system reliability and reduces risk of costly refrigerant loss. To prove our claim, Chandler
offers a five-year limited guarantee against leaks at tube sheets and center supports for all medium profile and large unit cooler models.
13
PRO3 Top Mount Packaged Refrigeration Systems
Models PTN/PTT are an evaporator and condensing unit all in one package. This unit is designed
to maximize storage area inside a cooler or freezer and is ideal for small- to medium-sized restaurant
and convenience store application where holding temperature is the primary goal.
Shaded Pole motors standard for both condensing unit and evaporator section, PSC motors optional for
for both condensing unit and evaporator section, EC motors available for evaporator section only.
EASE OF INSTALLATION AND SERVICE
ENERGY EFFICIENT | ENVIRONMENTALLY FRIENDLY
• Installation takes a fraction of the time required for a split system:
no piping or loose components to install, refrigerant is pre-charged
at factory and a field superheat adjustment is not required (see
installation manual for more information)
• Energy Solutions® energy-efficient motors from InterLink™
Commercial Refrigeration Parts:
– PSC motors standard in both condensing unit and
evaporator section
– EC motors optional, but may be required in certain installations
(evaporator section only)
• No drain line required for indoor units. Indoor models come with a
condensate evaporation pan
• Flexible design allows for multiple installation methods: optimized for
indoor use, but outdoor models available with weatherhood installed.
Outdoor models also come with: crankcase heater, drain line heater
and fan-cycling for head pressure control
• Maximizes storage area in a cooler or freezer: evaporator grill mounts
flush on a standard 4 or a recessed in a 5-1/2" ceiling panel
• Reduced refrigerant charge: system uses as little as 10 percent* of
refrigerant required for a comparable split system
RELIABLE | DURABLE
• System is fully-assembled and quality-tested at the factory
• Electronic control provides accurate temperature control
EASE OF USE
• Liquid-line filter drier (medium and large cabinet only)
• System is factory-assembled, evacuated, charged, run-tested and
wired; no additional components or refrigerant charging required;
most models come with a 26 power cord ready to plug-in
• Two-year parts warranty
* Results may vary. Estimate based on a typical 25-foot refrigerant line.
• Controls preset for typical applications: +35° F for coolers, -10° F, for
freezers and are easy to adjust (019L6 set for 0° F)
Performance Data
Coolers - Air Defrost System
Model
PTN024H2
PTN029H2
PTN040H2
PT*047H2
PT*063H2
PT*072H2
PT*099H2
PT*128H2
Freezers - Electric Defrost Systems
90° F Ambient
35° F
38° F
2,630
2,740
3,170
3,290
4,380
4,500
5,150
5,480
6,910
7,340
7,890
8,330
10,850
11,730
14,030
15,010
Model
PTN019L6
PT*021L6
PT*031L6
PT*044L6
PT*052L6
PT*069L6
0° F
2,640
2,860
4,500
6,260
7,470
9,670
90° F Ambient
-10° F
–
2,300
3,400
4,830
5,720
7,850
-20° F
–
1,430
2,200
3,630
4,170
5,600
MEA Accepted
Electrical Data
Model
Voltage
MCA
MOPD
PTN024H2A^
PTN029H2A^
PTN040H2A^
PT*047H2A^
PT*047H2B^
PT*063H2B^
PT*072H2B^
PT*099H2B^
PT*099H2C^
PT*128H2B^
PT*128H2C^
PTN019L6A^
PT*021L6A^
PT*021L6B^
PT*031L6B^
PT*044L6B^
PT*052L6B^
PT*052L6C^
PT*069L6B^
PT*069L6C^
115/1/60
115/1/60
115/1/60
115/1/60
208-230/1/60
208-230/1/60
208-230/1/60
208-230/1/60
208-230/3/60
208-230/1/60
208-230/3/60
115/1/60
115/1/60
208-230/1/60
208-230/1/60
208-230/1/60
208-230/1/60
208-230/3/60
208-230/1/60
208-230/3/60
10.2
10.6
11.7
16.9
8.6
11.6
10.9
17.1
15.4
20.3
14.8
13.0
14.5
7.6
13.8
15.9
18.1
12.2
23.8
15.9
15
15
15
20
15
15
15
20
20
30
20
20
20
15
15
20
20
15
30
20
*T For Outdoor, N for Indoor.
^ H for PSC, E for EC motor on evaporator section only.
14
Unit
Amps
10.2
10.6
11.7
14.2
7.3
9.9
9.3
14.7
13.3
17.2
12.8
13.0
12.3
6.5
11.6
13.3
15.3
13.0
20.0
14.2
Evaporator
CFM
340
340
340
350
350
550
500
875
875
825
825
340
350
350
550
520
900
900
875
875
Plug
Supplied
Yes
Yes
Yes
Yes
Yes 1
Yes 1
Yes 1
Yes 1
No
No
No
Yes
Yes
Yes 1
Yes 1
Yes 1
Yes 1
No
No
No
Matching NEMA
Receptacle
5-20R
5-20R
5-20R
5-20R
6-15R
6-15R
6-15R
6-20R
–
–
–
5-20R
5-20R
6-15R
6-15R
6-20R
6-20R
–
–
–
1 Plug Supplied on Indoor models only.
2
See technical bulletin for dimensions.
Cabinet Size2
Small
Small
Small
Medium
Medium
Medium
Medium
Large
Large
Large
Large
Small
Medium
Medium
Medium
Medium
Large
Large
Large
Large
Approx. Net
Weight (lbs.)
88
90
92
192
192
207
211
270
265
290
285
101
213
213
221
225
275
270
280
275
PRO3 Side Mount Packaged Refrigeration Systems
Model PST is an evaporator and condensing unit all in one package. This unit is optimized for
outdoor applications and is ideal for small- to medium-sized restaurant and convenience store
applications where maximum airflow is essential for pulling down the temperature of foods
or beverages. The Side Mount PRO3 is also available with electric defrost medium temperature
models, ensuring maximum performance in storage applications slightly above freezing.
PSC motors standard for both condensing unit and evaporator section, EC motors available
for evaporator section only.
EASE OF INSTALLATION AND SERVICE
• Installation takes a fraction of the time required for a split system:
refrigerant is pre-charged at factory, superheat adjustment is not
required and unit slides into slots in standard walk-in panel (see
installation manual for more information)
• Designed for simple serviceability: the condensing unit section’s
cabinet door can be quickly removed; in addition, the electrical box is
located outside the cabinet for easy access
• Electric defrost standard for medium temperature models, allowing
for maximum performance in storage applications just above 32°F
• Fan-cycling for head pressure control
• Crankcase heater
• Drain line heater
RELIABLE | DURABLE
• Flexible design allows for multiple installation methods: Optimized
for outdoor use, but can be used indoors as well (with drain
connection)
• System is fully-assembled and quality-tested at the factory
• Lifting lugs and hanging brackets in evaporating section allow for
easy installation
• Liquid-line filter drier
EASE OF USE
• Electronic microprocessor control provides accurate
temperature control
• Two-year parts warranty
ENVIRONMENTALLY FRIENDLY
• System is factory-assembled, evacuated, charged, run-tested and
wired; no additional components required
• Controls preset for typical applications: +38° F for high temp. coolers,
+35° F for medium temp. coolers, -10° F for freezers and are easy
to adjust
PERFORMANCE
• Maximized airflow: evaporator placement in walk-in box with pullthrough fans
– Suitable for temperature pull-down and holding temperature
• Increased condenser capacity, by avoiding compressor heat across
the coil
– Improved tolerance in high-ambient conditions
• Energy Solutions® energy-efficient motors from InterLink™
Commercial Refrigeration Parts:
– PSC motors standard in both condensing unit and
evaporator section
– EC motors optional, but may be required in certain installations
(evaporator section only)
• Reduced refrigerant charge: the PRO3 Side Mount packaged
refrigeration system can use as little as 10-15 percent* of refrigerant
required for a comparable split system
*Results may vary. Estimate based on a typical a typical 100-foot refrigerant
line length.
Performance Data
Coolers - Air Defrost System
Model
PST070H6B^
PST090H6B^
PST131H6B^
PST147H6B^
MEA Accepted
Coolers - Electric Defrost System
90° F Ambient
35° F
38° F
6,860
7,198
8,928
9,363
12,859
13,540
14,545
15,245
Model
PST066M6B^
PST086M6B^
PST124M6B^
PST141M6B^
90° F Ambient
35° F
6,860
8,928
12,859
14,545
Freezers - Electric Defrost System
Model
PST034L6B^
PST051L6B^
PST057L6B^
PST077L6B^
90° F Ambient
0° F
-10° F -20° F
5,031
3,651
2,395
6,922
5,428
3,943
7,994
6,079
4,153
10,602 8,179
6,030
Electrical Data
Model
PST070H6B^
PST090H6B^
PST131H6B^
PST147H6B^
PST066M6B^
PST086M6B^
PST124M6B^
PST141M6B^
PST034L6B^
PST051L6B^
PST057L6B^
PST077L6B^
Voltage
208-230/1/60
208-230/1/60
208-230/1/60
208-230/1/60
208-230/1/60
208-230/1/60
208-230/1/60
208-230/1/60
208-230/1/60
208-230/1/60
208-230/1/60
208-230/1/60
MCA
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
20.7
MOPD
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
35.0
Evaporator CFM
625
625
1,350
1,350
625
625
1,350
1,350
625
625
1,350
1,350
Cabinet Size¹
Small
Small
Large
Large
Small
Small
Large
Large
Small
Small
Large
Large
Approx. Net Weight (lbs.)
260
265
320
325
260
265
320
325
260
265
320
325
^ H for PSC, E for EC motor on evaporator section only.
1
See technical bulletin for dimensions.
15
Condensing Units
1/2 - 5 HP Indoor/Outdoor Condensing Units
with Hermetic Compressors
Model CH
condensing units are ideal for convenience store, restaurant and other
commercial applications. The CH model condensing units feature a hermetic refrigeration
compressor with oversized HyperCore™ microchannel condenser. Also, the CH Series
condensing units have a shut off valve in the discharge line of the hermetic compressor.
PSC motors come standard to help you save energy. UL listed for US and Canada.
Available with factory installed Smart Defrost Kit™ (SDK) system and Variable Speed
EC (VSEC) motor with Orbus™ Controller.
HyperCore
TM
microchannel coil technology
Variable Speed EC (VSEC) motors with Orbus™ Controller by InterLink™
VSEC motors by InterLink™ with the proprietary Orbus™ Controller are available as an option on 1/2-6 HP air-cooled
condensing units from Chandler. Choosing this option saves energy and reduces costs for the end user by controlling the
speed of motors in response to loads.
To achieve an optimal system that is both energy efficient and environmentally friendly,
choose the following options for your unit:
VSEC motors with Orbus™ Controller, factory-installed Smart Defrost Kit™ and a variety of
compressor options, including efficient scroll, hermetic and semi-hermetic compressor.
These options provide unmatched energy efficiency — the perfect solution for applications
where energy savings is essential for success.
CH Series Indoor or Outdoor Installation, Hermetic Compressors (1/2 - 5 HP)
CH
Model
CH*005H6
CH*009H6
CH*010H6†
CH*015H6
CH*025H6
CH*032H6
CH*040H6
CH*050H6
CH*005X6
CH*008X6
CH*009X6
CH*010X6†
CH*015X6
CH*020X6
CH*025X6
CH*030X6
CH*032X6
CH*040X6
CH*050X6
CH*011L6
CH*014L6
CH*019L6
CH*025L6
CH*031L6
CH*005H2
CH*008H2
CH*010H2
CH*015H2
CH*020H2
CH*029M2
CH*030H2
CH*040H2
CH*050H2
Compressor Refrigerant
RST45C1E
RST64C1E
RS70C1E
CS10K6E
CS14K6E
CS20K6E
CS27K6E2
CS33K6E2
RST45C1E
RST55C1E
RST64C1E
RS70C1E
CS10K6E
CS12K6E
CS14K6E
CS18K6E
CS20K6E
CS27K6E
CS33K6E
CF04K6E
CF06K6E
CF06K6E
CF09K6E
CF12K6E
ART82C1
RS64C2
RS70C1
CR18KQ
CR24KQ
CR37KQ
CR37KQ
CR53KQ
CRN-0500
Suction
Temp.
High Temp
R-404A/507
35°F
Extended
Temp
R-404A/507
25°F
Low Temp
R-404A/507
-10°F
Medium &
High Temp
R-22
25°F
* = T for Outdoor, N for Indoor, S for Beacon II™
† = RS compressor not suitable for R-507
1
Minimum Circuit Amps - Air Defrost Type Unit
2
230 Volt only
16
Capacity (BTUH) Connections (ID)
95° F Ambient
7,790
11,080
11,960
18,400
23,030
37,110
45,670
50,060
5,970
7,070
8,420
8,850
13,960
16,000
17,490
25,490
27,890
37,270
41,000
4,920
7,750
8,750
12,000
14,360
4,870
7,740
8,150
12,210
16,910
22,780
28,090
38,840
44,050
Liquid Suction
3/8
3/8
3/8
3/8
3/8
1/2
1/2
1/2
3/8
3/8
3/8
3/8
3/8
3/8
3/8
1/2
1/2
1/2
1/2
3/8
3/8
3/8
3/8
1/2
3/8
3/8
3/8
3/8
3/8
1/2
1/2
1/2
1/2
1/2
5/8
5/8
5/8
7/8
7/8
1-1/8
1-1/8
1/2
1/2
5/8
5/8
5/8
7/8
7/8
7/8
7/8
1-1/8
1-1/8
5/8
5/8
5/8
7/8
7/8
1/2
1/2
5/8
5/8
7/8
7/8
7/8
1-1/8
1-1/8
Unit MCA1
Dimensions (in.)
208-230/1 208-230/3 460/3
15.0
15.0
15.0
15.0
20.0
25.9
33.1
41.2
15.0
15.0
15.0
15.0
15.0
15.0
15.0
21.0
24.0
30.3
38.0
15.0
15.0
15.0
20.0
22.3
15.0
15.0
15.0
15.0
20.0
21.8
24.3
36.0
42.0
–
–
15.0
15.0
15.0
20.2
21.1
24.2
–
–
–
15.0
15.0
15.0
15.0
15.0
20.0
20.7
24.5
15.0
15.0
15.0
15.0
15.0
–
–
15.0
15.0
15.0
15.0
30.0
23.9
28.0
–
–
–
–
–
–
–
–
–
–
–
–
–
–
15.0
15.0
15.0
15.0
15.0
–
–
–
–
15.0
–
–
–
15.0
15.0
15.0
15.0
15.0
15.0
L
H
D
23-3/4
23-3/4
23-3/4
37-3/4
37-3/4
42-1/2
42-1/2
42-1/2
23-3/4
23-3/4
23-3/4
23-3/4
37-3/4
37-3/4
37-3/4
42-1/2
42-1/2
42-1/2
42-1/2
23-3/4
23-3/4
37-3/4
37-3/4
37-3/4
23-3/4
23-3/4
23-3/4
37-3/4
37-3/4
37-3/4
42-1/2
42-1/2
42-1/2
17-1/4
17-1/4
17-1/4
17-1/4
17-1/4
29-3/4
29-3/4
29-3/4
17-1/2
17-1/2
17-1/2
17-1/4
17-1/4
17-1/4
17-1/4
29-3/4
29-3/4
29-3/4
29-3/4
17-1/4
17-1/4
17-1/4
17-1/4
19-3/4
17-1/4
17-1/4
17-1/4
17-1/4
17-1/4
19-1/4
29-3/4
29-3/4
29-3/4
28-1/4
28-1/4
28-1/4
28-1/4
28-1/4
30-1/4
30-1/4
30-1/4
28-1/4
28-1/4
28-1/4
28-1/4
28-1/4
28-1/4
28-1/4
30-1/4
30-1/4
30-1/4
30-1/4
28-1/4
28-1/4
28-1/4
28-1/4
28-1/4
28-1/4
28-1/4
28-1/4
28-1/4
28-1/4
28-1/4
30-1/4
30-1/4
30-1/4
Approx.
Net Wt.
(lbs.)
135
144
138
193
208
275
281
313
135
135
144
138
193
203
208
290
275
281
313
139
170
200
222
223
135
141
136
189
193
214
281
299
310
Condensing Units
2 - 6 HP Indoor/Outdoor Condensing Units with Scroll® Compressors
Model CZ features a complete line of Copeland’s Scroll® compressors. These condensing units have an oversized HyperCore™ microchannel
condenser which allows units to operate in high ambient for 40° F suction temperature and below. PSC motors come standard to help
you save energy. UL listed for US and Canada. Available with factory installed Smart Defrost Kit™(SDK) system and Variable Speed EC
(VSEC) motor with Orbus™ Controller.
CZ Series Indoor or Outdoor Installation, Scroll® Compressors (2-6 HP)
CZ Model
CZ*020M6
CZ*025M6
CZ*030M6
CZ*035M6
CZ*045M6
CZ*055M6
CZ*060M6
CZ*020L6
CZ*025L6
CZ*030L6
CZ*035L6
CZ*045L6
CZ*055L6
CZ*060L6
Compressor Refrigerant
ZS15K4E
ZS19K4E
ZS21K4E
ZS26K4E
ZS30K4E
ZS38K4E
ZS45K4E
ZF06K4E
ZF08K4E
ZF09K4E
ZF11K4E
ZF13K4E
ZF15K4E
ZF18K4E
Suction
Temp.
Medium
Temp.
R-404A/
507
25°F
Low Temp.
R-404A/
507
-10°F
Capacity (BTUH)
95°F Ambient
18,930
22,490
27,270
32,820
38,230
45,160
52,340
9,540
11,850
13,200
15,860
19,490
23,820
28,970
Connections (in.)
Liquid Suction
IDS
IDS
1/2
7/8
1/2
7/8
1/2
7/8
1/2
7/8
1/2
1-1/8
1/2
1-1/8
1/2
1-1/8
1/2
7/8
1/2
7/8
1/2
7/8
1/2
7/8
1/2
1-1/8
1/2
1-1/8
1/2
1-1/8
208230/1
20
20
22
27
34
40
–
20
20
20
24
34
40
–
Unit MCA1
208230/3
15
15
20
20
20
28
30
15
15
15
20
20
28
30
Dimensions (in.)
460/3
L
H
D
15
15
15
15
15
15
15
15
15
15
15
15
15
15
37-3/4
37-3/4
42-1/2
42-1/2
42-1/2
42-1/2
42-1/2
37-3/4
37-3/4
37-3/4
37-3/4
42-1/2
42-1/2
42-1/2
19-3/4
19-3/4
29-3/4
29-3/4
29-3/4
29-3/4
29-3/4
19-3/4
19-3/4
19-3/4
19-3/4
29-3/4
29-3/4
29-3/4
28-1/4
28-1/4
30-1/4
30-1/4
30-1/4
30-1/4
30-1/4
28-1/4
28-1/4
28-1/4
28-1/4
30-1/4
30-1/4
30-1/4
Approx.
Net Wt.
(lbs.)
209
218
287
290
317
317
317
209
218
218
217
307
313
317
NOTE: The ZF compressor comes with liquid injection.
For R-22 model capacity information, see product bulletin.
1/2 - 5 HP Indoor/Outdoor Condensing Units with Semi-Hermetic Compressors
Model CS
condensing units are ideal for convenience store, restaurant and other commercial applications. The units feature a semi-hermetic
refrigeration compressor, which is spring-mounted with vibration eliminators on all 1-1/2 to 6 HP (1/2 to 1 HP compressors are rigid mounted and
have a discharge loop). Also, these condensing units come standard with an oversized HyperCore™ microchannel coil technology condenser that works
in high ambients, encapsulated auto-reset high pressure controls to eliminate leaks, pre-painted steel cabinet for superior strength and
corrosion protection, and suction and discharge service valves. PSC motors come standard to help you save energy. UL listed for US and
Canada. Available with factory installed Smart Defrost Kit™(SDK) system and Variable Speed EC (VSEC) motor with Orbus™ Controller.
CS Series Indoor or Outdoor Installation, Semi-Hermetic Compressors (1/2-5 HP)
CS
Model
CS*005H2
CS*008H2
CS*008M2
CS*010H2
CS*010M2
CS*015H2
CS*020H2
CS*020M2
CS*021M2
CS*029M2
CS*030H2
CS*040H2
CS*050H2
CS*050M2
CS*005M6
CS*010M6
CS*020M6
CS*021M6
CS*030M6
CS*040M6
CS*005L6
CS*008L6
CS*010L6
CS*015L6
CS*020L6
CS*021L6
CS*030L6
CS*030E6
CS*040L6
Compressor
HAG-0050
KAN-0075
KAE-0075
KAR-0100
KAM-0100
KAG-0150
ERA-0200
KAK-0200
ERC-0200
ERF-0310
ERF-0310
NRB-0400
NRA-0500
NRM-0500
HAJ-005E
KAR-010E
KAK-020E
ERC-021E
ERF-031E
NRB-040E
KAN-005E
KAM-007E
KAJ-010E
KAL-015E
EAD-020E
EAV-021E
LAH-032E
LAC-032E
NRD-040E^
NRD-032E^^
Refrigerant
Suction
Temp.
Medium &
High Temp
R-22
25°F
Medium
Temp
R-404A/507
25°F
Low Temp
R-404A/507
-10°F
Capacity (BTUH)
95° F Ambient
* = T for Outdoor, N for Indoor, S for Beacon II™
^ NRD1-040E Compressor is Single Phase & uses R-404A only.
^^ Uses R-404A & 507 in 3 phase model.
4,280
6,630
7,510
9,260
9,580
12,230
13,700
16,530
17,640
24,720
26,800
37,830
43,310
51,590
5,210
9,140
16,240
18,850
29,690
39,240
2,580
4,320
5,790
8,920
9,870
11,280
16,930
15,700††
22,530
Connections (in.)
Liquid
Suction
(IDS)
(IDS)
3/8
1/2
3/8
5/8
3/8
5/8
3/8
5/8
3/8
5/8
3/8
7/8
3/8
7/8
3/8
7/8
3/8
7/8
1/2
7/8
1/2
7/8
1/2
1-1/8
1/2
1-1/8
1/2
1-1/8
3/8
1/2
3/8
5/8
3/8
7/8
3/8
7/8
1/2
7/8
1/2
1-1/8
3/8
1/2
3/8
5/8
3/8
5/8
3/8
7/8
3/8
7/8
3/8
7/8
1/2
7/8
1/2
7/8
1/2
1-1/8
208230/1
15
15
15
15
15
15
15†
15
15†
21†
23†
–
–
–
15
15
15
–
23†
–
15
15
15
15
15†
20
20†
20†
35†
Unit MCA1
208230/3
15
15
15
15
15
15
15
15
15
15
20
28
25
31
–
15
15
15
20
28
15
15
15
15
15
15
20
15
22
Minimum Circuit Amps - Air Defrost Type Unit
† Units are 230 volt
† † Rated at -20˚ F
Dimensions (in.)
460/3
L
H
D
–
–
–
–
–
15
15
–
15
15
15
15
15
15
–
–
–
15
15
15
–
–
–
–
–
15
15
15
23-3/4
23-3/4
23-3/4
23-3/4
23-3/4
37-3/4
37-3/4
37-3/4
37-3/4
37-3/4
42-1/2
42-1/2
42-1/2
42-1/2
23-3/4
23-3/4
37-3/4
37-3/4
42-1/2
42-1/2
23-3/4
23-3/4
23-3/4
37-3/4
37-3/4
37-3/4
37-3/4
37-3/4
17-1/4
17-1/4
17-1/4
17-1/4
17-1/4
17-1/4
17-1/4
17-1/4
17-1/4
19-3/4
29-3/4
29-3/4
29-3/4
29-3/4
17-1/4
17-1/4
17-1/4
17-1/4
29-3/4
29-3/4
17-1/4
17-1/4
17-1/4
17-1/4
17-1/4
17-1/4
19-3/4
19-3/4
28-1/4
28-1/4
28-1/4
28-1/4
28-1/4
28-1/4
28-1/4
28-1/4
28-1/4
28-1/4
30-1/4
30-1/4
30-1/4
30-1/4
28-1/4
28-1/4
28-1/4
28-1/4
30-1/4
30-1/4
28-1/4
28-1/4
28-1/4
28-1/4
28-1/4
28-1/4
28-1/4
28-1/4
Approx.
Net Wt.
(lbs.)
161
180
180
175
178
221
293
189
301
391
385
460
462
462
161
178
189
301
397
460
172
172
178
225
291
301
357
391
15
42-1/2
29-3/4
30-1/4
457
1
17
Condensing Units
3-22 HP Indoor or Outdoor Condensing Units with Discus® or Scroll® Compressors
Models HD/HZ 3-22 HP condensing unit’s enhanced grill design gives up to 40% more free-air area than before and
its vertical receiver needs less refrigerant to ensure a solid column of liquid reaches the expansion valve. Fan motors
and serviceable components are accessible through the front grill for quick service and the sight glass is conveniently
placed so that charging is quick, easy and accurate. Thorough cleaning of the coil is easier because the unit’s top is one
piece and lighter for easy removal. A liquid base valve and suction service tap is placed on the outside of the cabinet
for easy pump-downs and quick diagnosis. The footprint is smaller for easy jobsite placement. These condensing units
utilize the Floating Tube™ coil design, which eliminates tube-sheet leaks, allowing Chandler to offer you a 5-year warranty
(including labor and refrigerant) against tube-sheet leaks. PSC motors come standard to help you save energy.
HD Discus® Models
Unit
Model
Compressor
Model
HD*0500H2
HD*0501H2
HD*0750H2
HD*0751H2
HD*0800H2
HD*1000H2
HD*1200H2
HD*1500H2
HD*0500M6
HD*0501M6
HD*0750M6
HD*0751M6
HD*0800M6
HD*1000M6
HD*1200M6
HD*1500M6
HD*0300L6
HD*0400L6
HD*0600L6
HD*0601L6
HD*0750L6
HD*0900L6
HD*1000L6
HD*1200L6
HD*1500L6
HD*2200L6
HD*0300L2
HD*0400L2
HD*0600L2
HD*0601L2
HD*0750L2
HD*0900L2
HD*1000L2
HD*1200L2
HD*1500L2
HD*2200L2
2DC3R53KE
2DD3R63KE
2DL3R78KE
2DA3R89KE
3DA3R10ME
3DB3R12ME
3DF3R15ME
3DS3R17ME
2DC3R53KE
2DD3R63KE
2DL3R78KE
2DA3R89KE
3DA3R10ME
3DB3R12ME
3DF3R15ME
3DS3R17ME
2DF3F16KE
2DL3F20KE
2DB3F25KE
3DA3F28KE
3DB3F33KE
3DF3F40KE
3DS3F46KE
4DA3F47KE
4DL3F63KE
4DT3F76KE
2DF3F16KE
2DL3F20KE
2DB3F25KE
3DA3F28KE
3DB3F33KE
3DF3F40KE
3DS3F46KE
4DA3F47KE
4DL3F63KE
4DT3F76KE
Refrigerant
Suction
BTUH
Temp. 95°F Amb.
High Temp.
R-22
25°F
Medium
Temp.
R-404A/R507
20°F
Low Temp.
R-404A/R507
-10°F
Low Temp.
R-22
-10°F
43,380
49,380
61,860
71,930
88,450
103,250
115,210
134,780
39,280
45,530
56,000
68,060
80,170
93,930
111,940
128,610
25,320
29,620
35,160
38,920
45,630
59,280
64,870
70,880
89,380
103,010
22,160
25,870
31,180
34,760
42,060
53,290
57,230
63,600
79,760
92,430
HZ Scroll® Models
Unit
Model
Compressor
Model
HZ*0650M6
HZ*0700M6
HZ*0750M6
HZ*0860M6
HZ*1000M6
HZ*1401M6
HZ*0750L6
HZ*1000L6
HZ*1300L6
HZ*1500L6
HZ*0750L2
HZ*1000L2
HZ*1300L2
HZ*1500L2
ZB50KCE
ZB58KCE
ZB66KCE
ZB76KCE
ZS92K4E
ZS11M4E
ZF24K4E
ZF33K4E
ZF40K4E
ZF48K4E
ZF24K4E
ZF33K4E
ZF40K4E
ZF48K4E
Refrigerant
Medium
Temp. R404A/R-507
25°F
Low Temp.
R-404A/R507
-10°F
Low Temp.
R-22
-10°F
*= T for Outdoors, N for Indoors, S for Beacon II™
18
Suction
BTUH
Temp. 95°F Amb.
58,130
69,460
80,250
90,090
108,200
128,920
32,650
45,630
57,900
65,370
30,610
42,940
53,530
60,860
Air Defrost
Min. Circuit Amp
208460/3/60
230/3/60
27.7
15.0
27.7
15.0
38.1
20.0
41.3
20.0
51.4
26.2
54.3
26.2
59.4
30.2
75.7
36.9
27.7
15.0
27.7
15.0
38.1
20.0
41.3
20.0
51.4
26.2
54.3
26.2
59.4
30.2
75.7
36.9
20.6
10.8
32.2
13.4
34.4
16.8
32.7
15.4
37.2
19.5
46.9
22.6
51.9
24.6
59.9
30.0
67.8
33.9
80.9
40.5
20.6
15.0
32.2
15.0
34.4
20.0
32.7
20.0
37.2
20.0
46.9
22.6
51.9
24.6
59.9
30.0
67.8
33.9
80.9
40.5
Air Defrost
Min. Circuit Amp
208460/3/60
230/3/60
34.8
18.7
39.9
22.2
39.1
23.4
51.9
23.4
64.7
31.8
76.1
36.0
36.4
19.5
51.6
25.5
64.7
33.4
67.1
31.0
36.4
19.5
51.6
25.5
64.7
33.4
67.1
31.0
Connections (in.)
Dimensions (inches)
Liquid
Suction
Length
Width
Height
Net
Wt.
(lbs.)
1/2
1/2
1/2
5/8
5/8
5/8
5/8
7/8
1/2
1/2
1/2
5/8
5/8
5/8
5/8
7/8
1/2
1/2
1/2
1/2
1/2
5/8
5/8
7/8
7/8
7/8
1/2
1/2
1/2
1/2
1/2
5/8
5/8
7/8
7/8
7/8
1-1/8
1-1/8
1-1/8
1-3/8
1-3/8
1-3/8
1-3/8
1-5/8
1-1/8
1-1/8
1-1/8
1-3/8
1-3/8
1-3/8
1-3/8
1-5/8
1-1/8
1-1/8
1-1/8
1-1/8
1-1/8
1-3/8
1-3/8
1-5/8
1-5/8
1-5/8
1-1/8
1-1/8
1-1/8
1-1/8
1-1/8
1-3/8
1-3/8
1-5/8
1-5/8
1-5/8
36-3/4
36-3/4
36-3/4
36-3/4
36-3/4
36-3/4
36-3/4
41-3/4
36-3/4
36-3/4
36-3/4
36-3/4
36-3/4
36-3/4
36-3/4
41-3/4
36-3/4
36-3/4
36-3/4
36-3/4
36-3/4
36-3/4
36-3/4
41-3/4
41-3/4
41-3/4
36-3/4
36-3/4
36-3/4
36-3/4
36-3/4
36-3/4
36-3/4
41-3/4
41-3/4
41-3/4
51-3/4
51-3/4
51-3/4
63-3/4
63-3/4
63-3/4
63-3/4
75-1/8
51-3/4
51-3/4
51-3/4
63-3/4
63-3/4
63-3/4
63-3/4
75-1/8
51-3/4
51-3/4
51-3/4
51-3/4
51-3/4
63-3/4
63-3/4
75-1/8
75-1/8
75-1/8
51-3/4
51-3/4
51-3/4
51-3/4
51-3/4
63-3/4
63-3/4
75-1/8
75-1/8
75-1/8
39-1/4
39-1/4
39-1/4
39-1/4
39-1/4
39-1/4
39-1/4
48-3/4
39-1/4
39-1/4
39-1/4
39-1/4
39-1/4
39-1/4
39-1/4
48-3/4
39-1/4
39-1/4
39-1/4
39-1/4
39-1/4
39-1/4
39-1/4
48-3/4
48-3/4
48-3/4
39-1/4
39-1/4
39-1/4
39-1/4
39-1/4
39-1/4
39-1/4
48-3/4
48-3/4
48-3/4
751
751
761
985
1,020
1,045
1,065
1,182
751
751
761
985
1,020
1,045
1,065
1,182
737
741
751
781
805
1,030
1,035
1,199
1,234
1,224
737
741
751
781
805
1,030
1,035
1,199
1,234
1,224
Refrigerant Line
Connections (OD)
Dimensions (in.)
Liquid
Suction
Length
Width
Height
Net
Wt.
(lbs.)
1/2
5/8
5/8
5/8
5/8
7/8
1/2
1/2
5/8
5/8
1/2
1/2
5/8
5/8
1-1/8
1-3/8
1-3/8
1-3/8
1-3/8
1-5/8
1-1/8
1-1/8
1-3/8
1-3/8
1-1/8
1-1/8
1-3/8
1-3/8
36-3/4
36-3/4
36-3/4
36-3/4
36-3/4
41-3/4
36-3/4
36-3/4
36-3/4
36-3/4
36-3/4
36-3/4
36-3/4
36-3/4
51-3/4
63-3/4
63-3/4
63-3/4
63-3/4
75-1/8
51-3/4
51-3/4
63-3/4
63-3/4
51-3/4
51-3/4
63-3/4
63-3/4
39-1/4
39-1/4
39-1/4
39-1/4
39-1/4
48-3/4
39-1/4
39-1/4
39-1/4
39-1/4
39-1/4
39-1/4
39-1/4
39-1/4
574
800
813
818
908
1,235
671
671
910
891
671
671
910
891
Condensing Units
20 - 40 HP Outdoor Condensing Units with Discus® Compressors
Model HDH outdoor Discus® condensing unit features a leak resistant design which includes
the Floating Tube™ coil design. The HDH features a high efficiency Copeland Discus® compressor.
The electrical controls including compressor contactor and optional defrost control are located
in an easily accessible control box with a hinged cover. UL listed for US and Canada.
HDH Discus® Compressor Model
HDH
Model
HDH2000D6
HDH2500D6
HDH2600D6
HDH3000D6
HDH3500D6
HDH4000D6
HDH*2000D6
HDH*2500D6
HDH*2600D6
HDH*3000D6
HDH*3500D6
HDH*4000D6
HDH2700L6†
HDH3000L6†
HDH3100L6†
^ 230/3
* S for Beacon II™
†
Compressor
4DA3R18ME
4DH3R22ME
4DH3R22ME
4DJ3R28M3
6DH3R35ME
6DJ3R40ME
4DA3R18ME
4DH3R22ME
4DH3R22ME
4DJ3R28M3
6DH3R35ME
6DJ3R40ME
6DL3F93KE
6DT3F11ME
6DT3F11M3
Refrigerant
Suction
Temp.
Medium
Temp.
R-22
25ºF
Medium
Temp.
R-404A/
R-507
25ºF
Low Temp.
R-404A/
R-507
-10ºF
BTUH
95˚F
Amb.
143,470
190,910
197,260
225,520
280,600
322,590
148,750
191,910
200,370
231,280
281,570
325,470
134,870
146,440
153,480
Min. Circuit Amp
208-230/
3/60
87.9
105.3
109.7
123.0
137.8
176.3^
87.9
105.3
109.7
123.0
137.8
176.3
103.7
120.4
124.8
460/
3/60
43.9
52.7
54.9
61.5
68.9
88.1
43.9
52.7
54.9
61.5
68.9
88.1
51.9
60.2
62.4
Connections (in.)
Dimensions (in.)
Liquid
Suction
L
H
D
Approx.
Net Wt.
(lbs.)
7/8
1-1/8
1-1/8
1-1/8
1-1/8
1-1/8
7/8
1-1/8
1-1/8
1-1/8
1-1/8
1-1/8
1-1/8
1-1/8
1-1/8
1-5/8
2-1/8
2-1/8
2-1/8
2-1/8
2-1/8
1-5/8
2-1/8
2-1/8
2-1/8
2-1/8
2-1/8
2-1/8
2-1/8
2-1/8
102-1/2
102-1/2
132-1/2
132-1/2
132-1/2
132-1/2
102-1/2
102-1/2
132-1/2
132-1/2
132-1/2
132-1/2
102-1/2
102-1/2
132-1/2
48-3/4
48-3/4
48-3/4
48-3/4
48-3/4
48-3/4
48-3/4
48-3/4
48-3/4
48-3/4
48-3/4
48-3/4
48-3/4
48-3/4
48-3/4
42-1/4
42-1/4
42-1/4
42-1/4
42-1/4
42-1/4
42-1/4
42-1/4
42-1/4
42-1/4
42-1/4
42-1/4
42-1/4
42-1/4
42-1/4
1,131
1,206
1,362
1,372
1,492
1,542
1,131
1,206
1,362
1,372
1,492
1,542
1,206
1,406
1,452
Demand Cooling needs to be specified for use with R-22
19
Condensing Units
24 - 80 HP Dual Compressor Outdoor Condensing Units
Model HDD condensing unit is a dual compressor vertical discharge outdoor
condensing unit that utilizes Copeland Discus® compressors. A wide range of
options are available that are ideal for large cold storage or warehouse applications.
PSC motors come standard to help you save energy.
HDD Discus® Compressor Model
HDD
Model
Compressor
HDD3000H2
HDD4000H2
HDD5000H2
HDD5200H2
HDD6000H2
HDD7000H2
HDD7010H2
HDD8000H2
HDD3000M6
HDD4000M6
HDD5000M6
HDD5200M6
HDD6000M6
HDD7000M6
HDD8000M6
HDD3000C6
HDD4000C6
HDD5000C6
HDD6000C6
HDD7000C6
HDD8000C6
HDD2400L6
HDD3000L6
HDD4400L6
HDD5400L6
HDD6000L6
HDD2400L61
HDD3000L61
HDD4400L61
HDD5400L61
HDD6000L61
3DS3R17ME
4DA3R18ME
4DH3R22ME
4DH3R22ME
4DJ3R28ME
6DH3R35ME
6DG3R37ME
6DJ3R40ME
3DS3R17ME
4DA3R18ME
4DH3R22ME
4DH3R22ME
4DJ3R28ME
6DH3R35ME
6DJ3R40ME
3DS3R17ME
4DA3R18ME
4DH3R22ME
4DJ3R28ME
6DH3R35ME
6DJ3R40ME
4DA3F47KE
4DL3F63KE
4DT3F76KE
6DL3F93KE
6DT3F11ME
4DA3F47KE
4DL3F63KE
4DT3F76KE
6DL3F93KE
6DT3F11ME
Refrig.
High
Temp.
R-22
25°F
Medium
Temp.
R404A/
R-507
25°F
Comm.
Temp.
R404A/
R-507
10°F
Low
Temp.
R404A/
R-507
-10°F
Low
Temp.
R-22
-10°F
* MCA based on remote loads and one contactor
1
Must be ordered with demand cooling
20
Suction
Temp.
BTUH
95°F
Amb.
267,000
279,800
365,800
373,600
439,800
563,200
590,800
652,600
282,800
295,600
370,800
381,600
459,800
585,200
677,200
218,400
223,400
282,000
351,000
447,800
522,200
139,000
176,200
208,600
261,800
294,400
125,000
158,400
187,800
232,200
277,000
Air Defrost
Min. Circuit Amp*
230/3/60 460/3/60
66.6
136.4
150.4
75.2
181.9
90.9
96.9
193.9
108.9
217.8
129.2
258.3
294.4
147.2
163.8
327.6
136.4
66.6
150.4
75.2
181.9
90.9
193.9
96.9
217.8
108.9
258.3
129.2
327.6
163.8
136.4
66.6
150.4
75.2
181.9
90.9
217.8
108.9
258.3
129.2
327.6
163.8
108.0
54.0
122.2
61.1
145.8
72.9
179.0
89.5
221.0
110.5
108.0
54.0
122.2
61.1
145.8
72.9
179.0
89.5
221.0
110.5
Connections (in.)
Liquid
7/8
7/8
1-1/8
1-1/8
1-1/8
1-1/8
1-1/8
1-1/8
7/8
7/8
1-1/8
1-1/8
1-1/8
1-1/8
1-1/8
7/8
7/8
1-1/8
1-1/8
1-1/8
1-1/8
7/8
7/8
7/8
1-1/8
1-1/8
7/8
7/8
7/8
1-1/8
1-1/8
Suction
1-5/8
1-5/8
2-1/8
2-1/8
2-1/8
2-1/8
2-1/8
2-1/8
1-5/8
1-5/8
2-1/8
2-1/8
2-1/8
2-1/8
2-1/8
1-5/8
1-5/8
2-1/8
2-1/8
2-1/8
2-1/8
1-5/8
1-5/8
2-1/8
2-1/8
2-1/8
1-5/8
1-5/8
2-1/8
2-1/8
2-1/8
Dimensions (in.)
L
151
151
151
179
179
233
233
233
151
151
151
179
179
233
233
151
151
151
179
233
233
151
151
151
151
179
151
151
151
151
179
H
61
61
61
61
61
61
61
61
61
61
61
61
61
61
61
61
61
61
61
61
61
61
61
61
61
61
61
61
61
61
61
D
88
88
88
88
88
88
88
88
88
88
88
88
88
88
88
88
88
88
88
88
88
88
88
88
88
88
88
88
88
88
88
Approx.
Net Wt.
(lbs.)
3,160
3,160
3,230
3,520
3,720
4,320
4,320
4,760
3,160
3,160
3,230
3,520
3,720
4,320
4,760
3,160
3,160
3,230
3,720
4,320
4,760
3,000
3,000
3,000
3,340
3,770
3,000
3,000
3,000
3,340
3,770
Condensing Units
1/2 - 6 HP Remote Water-Cooled Condensing Units with Hermetic or Scroll® Compressors
Models HWN/ZWN series are water-cooled hermetic and Scroll® condensing units from 1/2 - 6 HP.
Condensing units’ component selection, location, base and unit dimensions are all optimized for easy
field replacements or in new installations where space is limited. Extra space is provided inside the
electrical box for easy servicing. The area is large enough to accommodate circuit breakers, compressor
contactors, time clocks and all start components in one enclosure. Standard features include
compressor isolations valves that enable services technicians to isolate the compressor for service.
Also standard is the extra capacity receiver which provides total refrigerant pump down. Ideal for units
requiring long line runs. These units are available with Copeland hermetic, Scroll® low and medium
temperature compressors as well as hermetic low temperature compressors for R-22 and R-404A.
These units are UL listed for US and Canada.
HWN Hermetic Compressor Model
HWN
Model
Compressor
HWN005H2
HWN008H2
HWN010H2
HWN015H2
HWN020H2
HWN030H2
HWN040H2
HWN050H2
HWN005X6
HWN008X6
HWN009X6
HWN010X6
HWN015X6
HWN020X6
HWN025X6
HWN030X6
HWN032X6
HWN040X6
HWN050X6
HWN011L6
HWN014L6
HWN025L6
HWN031L6
ART82C1
RS64C2
RS70C1
CR18KQ
CR24KQ
CR37KQ
CR53KQ
CRN50500
RS43C2E†
RS55C2E†
RS64C2E†
RS70C2E†
CS10K6E
CS12K6E
CS14K6E
CS18K6E
CS20K6E
CS27K6E
CS33K3E
CF04K6E
CF06K6E
CF09K6E
CF12K6E
Refrigerant
Suction
Temp
Medium
& High
Temp
R-22
20° F
Extended
Temp
R-404A/
R-507
10° F
Low
Temp
R-404A/
R-507
-10° F
Capacity*
BTUH
5,390
7,500
8,810
11,240
14,330
23,660
33,740
40,460
4,060
5,280
6,395
6,800
9,710
11,490
13,630
17,400
19,220
23,901
28,838
5,310
8,700
12,590
16,060
Air Defrost
Total MCA
Connections (in.)
ODS
Dimensions
(in.)
208-230/
1/60
208-230/
3/60
460/
3/60
Liquid
Suction
L
H
D
Approx.
Net Wt.
(lbs.)
15
15
15
15
20
21
33
39
15
15
15
15
15
15
15
18
21
27
35
15
15
20
21
15
15
15
15
20
24
15
15
15
15
15
15
20
21
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
3/8
3/8
3/8
3/8
3/8
1/2
1/2
1/2
3/8
3/8
3/8
3/8
3/8
3/8
3/8
1/2
1/2
1/2
1/2
3/8
3/8
3/8
1/2
1/2
1/2
5/8
5/8
5/8
7/8
7/8
7/8
1/2
1/2
5/8
5/8
5/8
7/8
7/8
7/8
7/8
7/8
7/8
5/8
5/8
5/8
7/8
22
22
22
27
27
29
29
29
22
22
22
22
27
27
27
27
27
29
29
27
27
27
27
17
17
17
21
21
28
28
28
17
17
17
17
21
21
21
28
28
28
28
21
21
21
21
14
14
14
22
22
25
25
25
14
14
14
14
22
22
22
22
22
25
25
22
22
22
22
77
92
92
136
141
174
196
221
98
98
103
107
148
148
152
172
182
183
207
114
114
120
136
ZWN Scroll® Compressor Model
ZWN
Model
Compressor
ZWN030X6
ZWN035X6
ZWN045X6
ZWN055X6
ZWN060X6
ZWN030L6
ZWN035L6
ZWN045L6
ZWN055L6
ZWN060L6
ZS21K4E
ZS26K4E
ZS30K4E
ZS38K4E
ZS45K4E
ZF09K4E
ZF11K4E
ZF13K4E
ZF15K4E
ZF18K4E
Refrigerant
Suction
Temp
Extended
Temp
R-404A/
R-507
10° F
Low
Temp
R-404A/
R-507
-10° F
Capacity*
BTUH
19,740
24,490
28,480
34,970
41,850
13,200
16,200
19,100
23,300
27,700
Air Defrost
Total MCA
208-230/
1/60
18.4
23.2
30
36
18
23
30
36
-
208-230/
3/60
15
15.2
17
24
27
15
15
17
24
27
Connections (in.)
ODS
460/
3/60
15
15
15
15
15
15
15
15
15
15
Dimensions
(in.)
Liquid
Suction
L
H
D
Approx.
Net Wt.
(lbs.)
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
7/8
7/8
7/8
7/8
7/8
7/8
7/8
7/8
7/8
7/8
29
29
29
29
29
27
27
27
27
29
28
28
28
28
28
28
28
28
28
28
25
25
25
25
25
22
22
22
22
25
171
186
207
226
241
159
165
185
201
207
† Only for use with R-404A
* Capacity rating conditions based on: 85°F Entering Water, 105°F Condensing Temperature,
20°F ITD (ITD= condensing temperature - entering condenser water temperature), 0°F Subcooling.
21
Condensing Units
3/4 - 22 HP Indoor Water-Cooled Condensing Units
Model SWN
are “vessel-mounted” indoor water-cooled condensing units, complete with a shell and tube. The
cleanable water-cooled condenser is perfect for applications where air cooled condensers would not be practical, or
water is readily available. Available in sizes 3/4 - 22 HP in all temperature ranges, the SWN units are an economical,
compact selection.
Model SWN
SWN
Model
Compressor
SWN0075H2
SWN0075M2
SWN0090H2
SWN0100H2
SWN0150H2
SWN0200H2
SWN0200M2
SWN0300H2
SWN0400H2
SWN0499H2
SWN0500H2
SWN0750H2
SWN0760H2
SWN0761H2
SWN1000H2
SWN1500H2
SWN2000H2
SWN0090M6
SWN0199M6
SWN0200M6
SWN0310M6
SWN0500M6
SWN0150L6
SWN0200L6
SWN0210L6
SWN0310E6
SWN0310L6
SWN0311L6
SWN0400L6
SWN0599L6
SWN0600L6
SWN0601L6
SWN0750L6
SWN0900L6
SWN1000L6
SWN1500L6
SWN2200L6
KAN10075
KAE10075
KARA010E
KAM10100
KAGA0150
ERA10200
ERC10200
ERF10311
NRB20400
2DC3R53KE
2DD3R63KE
2DL3R78KE
2DA3R89KE
3DA3R10ME
3DB3R12ME
3DS3R17ME
4DA3R18ME
KARA010E
KAKA020E
ERCA021E
ERFA031E
2DC3R53KE
KALA016E
EADA020E
EAVA021E
LACA032E
LAHA032E
2DF3F16KE
2DL3F20KE
2DA3F23KE
2DB3F25KE
3DA3F28KE
3DB3F33KE
3DF3F40KE
3DS3F46KE
4DL3F63KE
4DT3F76KE
Refrig.
Suction Capacity*
Temp
(BTUH)
Medium
& High
Temp
R-22
25ºF
Medium
Temp
R-404A/
R-507
20ºF
Low
Temp
R-404A/
R-507
-20ºF
6,700
8,000
9,370
10,690
12,150
16,090
19,480
28,290
40,130
46,230
53,810
67,750
76,770
92,810
110,190
146,060
156,830
9,140
15,120
19,430
28,090
43,470
6,830
7,770
8,820
18,060
14,180
19,950
24,260
27,930
29,930
33,600
39,800
48,620
55,020
75,390
90,720
Air Defrost (Total MCA)
Dimensions (in.)
230/
1/60
208-230/
3/60
460/
3/60
Liquid
Suction
L
H
D
Approx.
Net Wt.
(lbs.)
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
20.0
-
15.0
15.0
20.0
20.0
15.0
20.0
20.0
28.7
-
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
24.4
25.0
25.0
35.4
35.9
46.0
48.9
66.9
65.9
15.0
15.0
15.0
15.0
25.0
15.0
15.0
15.0
15.0
15.0
20.0
29.5
32.3
31.7
30.0
34.5
41.5
46.5
59.0
74.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
20.0
20.0
22.4
22.4
29.5
32.9
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
20.0
20.0
20.8
29.5
37.0
3/8
3/8
3/8
3/8
3/8
3/8
3/8
1/2
1/2
5/8
5/8
5/8
5/8
5/8
7/8
7/8
7/8
3/8
3/8
3/8
1/2
5/8
3/8
3/8
3/8
1/2
1/2
1/2
1/2
5/8
5/8
5/8
5/8
5/8
7/8
7/8
7/8
5/8
5/8
5/8
7/8
7/8
7/8
7/8
1-1/8
1-1/8
1-3/8
1-3/8
1-3/8
1-3/8
1-3/8
1-5/8
1-5/8
1-5/8
7/8
7/8
7/8
1-1/8
1-3/8
7/8
7/8
7/8
1-1/8
1-1/8
1-3/8
1-3/8
1-3/8
1-3/8
1-3/8
1-5/8
1-5/8
1-5/8
2-1/8
2-1/8
3-3/4
3-3/4
3-3/4
3-3/4
3-3/4
3-3/4
3-3/4
26-3/4
26-3/4
30-1/3
30-1/3
35-1/3
35-1/3
35-1/3
35-1/3
35-1/3
35-1/3
23-3/4
23-3/4
23-3/4
26-3/4
30-1/3
23-3/4
23-3/4
23-3/4
26-3/4
26-3/4
26-3/4
26-3/4
30-1/3
30-1/3
30-1/3
35-1/3
35-1/3
35-1/3
35-1/3
35-1/3
37-1/3
37-1/3
37-1/3
37-1/3
37-1/3
37-1/3
37-1/3
36-1/3
36-1/3
39-1/4
39-1/4
41-1/2
41-1/2
41-1/2
41-1/2
41-1/2
41-1/2
37-1/3
37-1/3
37-1/3
36-1/3
39-1/4
37-1/3
37-1/3
37-1/3
36-1/3
36-1/3
36-1/3
36-1/3
39-1/4
39-1/4
39-1/4
41-1/2
41-1/2
41-1/2
41-1/2
41-1/2
33
33
33
33
33
33
33
38-1/3
38-1/3
42-1/2
42-1/2
55-1/2
55-1/2
55-1/2
55-1/2
55-1/2
55-1/2
33
33
33
38-1/3
42-1/2
33
33
33
38-1/3
38-1/3
38-1/3
38-1/3
42-1/2
42-1/2
42-1/2
55-1/2
55-1/2
55-1/2
55-1/2
55-1/2
165
165
180
180
195
260
260
325
385
400
400
465
465
465
715
735
795
180
210
260
325
400
195
325
325
325
325
340
385
415
415
430
465
560
715
780
865
* Capacity based on 85°F Entering Water, 105°F Condensing Temperature, 5°F Subcooling.
22
Connections (in.)
208-230/
1/60
Condensing Units
3/4 - 22 HP Remote Indoor Compressor Condensing Units
Model SRN are indoor compressor units designed for use with a remote air-cooled or evaporative
condenser. Typical applications include supermarkets, warehouses, convenience stores or wherever
outdoor roof or pad space is at a minimum. SRN units are available in sizes 3/4 - 22 HP in high, medium
and low temperature.
Model SRN
SRN
Model
Compressor
SRN0075H2
SRN0075M2
SRN0090H2
SRN0100H2
SRN0150H2
SRN0200H2
SRN0200M2
SRN0300H2
SRN0400H2
SRN0499H2
SRN0500H2
SRN0750H2
SRN0760H2
SRN0761H2
SRN1000H2
SRN1500H2
SRN2000H2
SRN0090M6
SRN0199M6
SRN0200M6
SRN0310M6
SRN0500M6
SRN0150L6
SRN0200L6
SRN0210L6
SRN0310E6
SRN0310L6
SRN0311L6
SRN0400L6
SRN0599L6
SRN0600L6
SRN0601L6
SRN0750L6
SRN0900L6
SRN1000L6
SRN1500L6
SRN2200L6
KAN10075
KAE10075
KARA010E
KAM10100
KAGA0150
ERA10200
ERC10200
ERF10311
NRB20400
2DC3R53KE
2DD3R63KE
2DL3R78KE
2DA3R89KE
3DA3R10ME
3DB3R12ME
3DS3R17ME
4DA3R18ME
KARA010E
KAKA020E
ERCA021E
ERFA031E
2DC3R53KE
KALA016E
EADA020E
EAVA021E
LACA032E
LAHA032E
2DF3F16KE
2DL3F20KE
2DA3F23KE
2DB3F25KE
3DA3F28KE
3DB3F33KE
3DF3F40KE
3DS3F46KE
4DL3F63KE
4DT3F76KE
Refrig.
Suction Capacity*
Temp
(BTUH)
Medium
& High
Temp
R-22
25ºF
Medium
Temp
R-404A/
R-507
20ºF
Low
Temp
R-404A/
R-507
-20ºF
5,970
7,110
8,360
9,580
10,920
13,100
17,260
25,580
35,260
41,290
48,320
61,380
69,680
84,740
101,120
134,160
143,520
7,780
12,850
16,310
24,080
37,370
6,470
7,310
8,270
17,070
13,250
19,080
23,110
26,710
28,620
32,330
38,370
46,850
52,890
72,720
86,710
Air Defrost (Total MCA)
208-230/
208-230/
230/1/60
1/60
3/60
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
20.0
15.0
24.4
25.0
25.0
35.4
35.9
46.0
48.9
66.9
65.9
15.0
15.0
15.0
15.0
15.0
20.0
15.0
25.0
15.0
15.0
15.0
15.0
20.0
15.0
20.0
15.0
20.0
15.0
28.7
20.0
29.5
32.3
31.7
30.0
34.5
41.5
46.5
59.0
74.0
Connections (in.)
460/
3/60
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
20.0
20.0
22.4
22.4
29.5
32.9
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
20.0
20.0
20.8
29.5
37.0
Dimensions (in.)
Liquid
Suction
L
H
D
3/8
3/8
3/8
3/8
3/8
3/8
3/8
1/2
1/2
5/8
5/8
5/8
5/8
5/8
7/8
7/8
7/8
3/8
3/8
3/8
1/2
5/8
3/8
3/8
3/8
1/2
1/2
1/2
1/2
5/8
5/8
5/8
5/8
5/8
7/8
7/8
7/8
5/8
5/8
5/8
7/8
7/8
7/8
7/8
1-1/8
1-1/8
1-3/8
1-3/8
1-3/8
1-3/8
1-3/8
1-5/8
1-5/8
1-5/8
7/8
7/8
7/8
1-1/8
1-3/8
7/8
7/8
7/8
1-1/8
1-1/8
1-3/8
1-3/8
1-3/8
1-3/8
1-3/8
1-5/8
1-5/8
1-5/8
2-1/8
2-1/8
23-3/4
23-3/4
23-3/4
23-3/4
23-3/4
23-3/4
23-3/4
26-3/4
26-3/4
30-1/3
30-1/3
35-1/3
35-1/3
35-1/3
35-1/3
35-1/3
35-1/3
23-3/4
23-3/4
23-3/4
26-3/4
30-1/3
23-3/4
23-3/4
23-3/4
26-3/4
26-3/4
26-3/4
26-3/4
30-1/3
30-1/3
30-1/3
35-1/3
35-1/3
35-1/3
35-1/3
35-1/3
36-1/3
36-1/3
36-1/3
36-1/3
36-1/3
36-1/3
36-1/3
39-1/4
39-1/4
39-1/4
39-1/4
43-1/2
43-1/2
43-1/2
43-1/2
43-1/2
43-1/2
36-1/3
36-1/3
36-1/3
39-1/4
39-1/4
36-1/3
36-1/3
36-1/3
39-1/4
39-1/4
39-1/4
39-1/4
39-1/4
39-1/4
39-1/4
43-1/2
43-1/2
43-1/2
43-1/2
43-1/2
35
35
35
35
35
35
35
40
40
42-1/2
42-1/2
47
47
47
47
47
47
35
35
35
40
42-1/2
35
35
35
40
40
40
40
42-1/2
42-1/2
42-1/2
47
47
47
47
47
Approx.
Net Wt.
(lbs.)
155
155
160
160
175
245
245
305
360
375
375
385
385
385
595
615
665
155
200
245
305
375
175
305
305
305
305
320
360
390
390
405
385
520
650
710
725
* Based on 110°F Condensing Temperature, 6°F Subcooling for Low Temp models and 120°F
Condensing Temperature, 8°F Subcooling for Medium & High Temp models.
23
1 - 26 Tons Air-Cooled Condensers
Model WSS air-cooled condensers are designed for efficient performance and low maintenance.
The units feature an aluminum cabinet for long life and attractive appearance. The aluminum fin,
copper tube coils have staggered tube design for high efficiency. All coils are dehydrated, pressure
tested, sealed with caps and pressurized for shipment. PSC motors come standard to help you save
energy.
Model WSS
WSS
Model
WSS008
WSS009
WSS010
WSS016
WSS024
WSS040
WSS049
WSS061
WSS070
WSS080
WSS105
WSS113
WSS133
Total Heat Rejection
30ºF TD
R-404A,
R-22
507
22.9
22.4
26.7
26.2
30.5
29.9
47.1
46.2
73.0
71.5
120.0
117.6
146.0
143.1
182.4
178.8
209.6
205.5
239.6
234.8
314.2
307.9
339.6
332.8
398.2
390.2
208/230/460/3/60 1140 RPM available
24
CFM
Motor
HP (1)
FLA
208/230/60/1
2,400
2,400
2,400
2,100
5,050
6,450
10,100
12,400
13,700
12,900
20,500
19,900
19,400
1/4
1/4
1/4
1/4
1/3
1/2
(2) 1/3
(2) 1/2
(2) 1/2
(2) 1/2
(3) 1/2
(3) 1/2
(3) 1/2
2.0
2.0
2.0
2.0
3.4
3.9
6.8
7.8
7.8
7.8
11.7
11.7
11.7
Dimensions
(in.)
Connections
(in.)
L
H
D
Inlet
Outlet
Approx.
Net Wt.
(lbs.)
37-1/2
37-1/2
37-1/2
37-1/2
39-3/4
49-3/4
69-3/4
69-3/4
89-3/4
89-3/4
129-3/4
129-3/4
129-3/4
22
22
22
40-1/2
40-1/2
40-1/2
40-1/2
40-1/2
40-1/2
40-1/2
40-1/2
40-1/2
40-1/2
43
43
43
43
43
43
43
43
43
43
43
43
43
3/8
5/8
7/8
7/8
1-1/8
1-1/8
(2) 1-1/8
(2) 1-1/8
(2) 1-1/8
(2) 1-3/8
(2) 1-5/8
(2) 1-5/8
(2) 1-5/8
3/8
5/8
5/8
5/8
7/8
7/8
(2) 7/8
(2) 7/8
(2) 7/8
(2) 1-1/8
(2) 1-1/8
(2) 1-1/8
(2) 1-1/8
96
96
96
114
180
260
450
470
510
530
550
580
625
Models HNE, HNQ, HNX, HNL and HNH Air-Cooled Condensers
EC and 830/540
series air-cooled condensers feature improved energy efficiency and low sound levels, which are key
features sought by the supermarket and grocery industry. Traditional condensers using 1140 RPM motors offer high capacities,
but cannot meet the low sound and energy efficiency standards demanded today by this industry. Now, Chandler brings the
best of both worlds together with advanced solutions that offer high capacities for operation, while meeting the low sound
and energy efficiency requirements you demand.
Model HNE with EC motor technology offers all the benefits of variable speed motors without the complexity. EC motors
utilize variable-speed technology, which optimizes fan speeds for load requirements, maximizes energy efficiency and
minimizes sound.
Models HNQ, HNX, and HNL features Chandler’s patented QuietEdge™ technology that uses specially designed swept
fan blades to reduce noise levels. These blades are uniquely designed for each motor speed, optimizing performance and
ensuring you’re receiving the lowest sound levels possible. Look for the QuietEdge™ 4 blade on the 540 RPM motors and the
QuietEdge™ 5 on the 830 RPM motors.
Model HNH continues to offer Chandler’s 1140 RPM series for customers seeking the most economical solution for their
capacity requirements.
EC Series Model HNE, 2.2 kW, 31.5" Fan Diameter
THR, MBH/1°F TD
Total FLA
HNE
Model
R-22
R-404A
HNES01A008
HNES01A009
HNES02A011
HNES02A015
HNES02A018
HNES03A023
HNES03A027
HNES04A031
HNES04A036
HNES05A039
HNES05A047
HNES06A056
HNES07A065
7.7
9.3
11.3
15.4
18.1
23.1
27.2
30.8
36.3
39.3
46.6
56.0
64.6
7.6
9.1
11.1
15.1
17.8
22.7
26.7
30.2
35.5
38.5
45.7
54.8
63.3
11,000
10,500
23,400
22,000
20,900
33,100
31,400
42,600
40,000
53,200
50,000
60,000
70,000
7.0
7.0
14.0
14.0
14.0
21.0
21.0
28.0
28.0
35.0
35.0
42.0
49.0
HNED04A023
HNED04A031
HNED04A036
HNED06A046
HNED06A054
HNED08A062
HNED08A073
HNED10A079
HNED10A093
HNED12A112
HNED14A129
22.7
30.8
36.3
46.2
54.4
61.7
72.5
78.6
93.3
111.9
129.2
22.2
30.2
32.5
45.3
53.3
60.5
71.1
77.0
91.4
109.7
126.7
46,700
44,100
41,800
66,100
62,700
85,100
80,000
106,400
100,100
120,100
140,100
28.0
28.0
28.0
42.0
42.0
56.0
56.0
70.0
70.0
84.0
98.0
CFM
230/3/60
460/3/60
Single Row
3.5
3.5
7.0
7.0
7.0
10.5
10.5
14.0
14.0
17.5
17.5
21.0
24.5
Double Row
14.0
14.0
14.0
21.0
21.0
28.0
28.0
35.0
35.0
42.0
49.0
Maximum No.
of Feeds
Connections
(in.)
Refrigerant
Summer Charge
R-22 (lbs.)
Approx.
Net Wt.
(lbs.)
7
14
14
21
28
21
28
21
28
21
28
28
28
1-3/8
1-3/8
1-3/8
1-5/8
2-1/8
2-1/8
2-1/8
2-1/8
2-5/8
2-5/8
2-5/8
2-5/8
(2) 2-5/8
8
10
10
15
29
22
30
51
70
64
86
102
118
330
360
590
640
690
930
1,010
1,220
1,320
1,520
1,650
1,960
2,260
28
42
56
42
56
42
56
42
56
56
56
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(4)
19
29
40
44
58
104
140
125
172
201
236
1,290
1,390
1,490
2,060
2,210
2,730
2,930
3,410
3,660
4,370
5,070
1-3/8
1-5/8
2-1/8
2-1/8
2-1/8
2-1/8
2-5/8
2-5/8
2-5/8
2-5/8
2-5/8
Bold indicates standard model capacity at 10 FPI
EC Series
830/540 Series
25
540 Series Model HNQ, 540 RPM, 0.5 HP, 30" Fan Diameter
HNQ
Model
THR, MBH/1°F TD
Total FLA
CFM
R-22
R-404A
230/3/60
HNQS01A005
HNQS01A006
HNQS02A008
HNQS02A010
HNQS02A011
HNQS03A016
HNQS03A017
HNQS04A021
HNQS04A023
HNQS05A026
HNQS05A029
HNQS06A034
HNQS07A042
5.2
6.1
8.0
10.3
11.5
15.6
17.2
20.7
22.9
25.9
28.6
34.4
41.6
5.1
5.9
7.8
10.1
11.2
15.2
16.9
20.3
22.4
25.4
28.1
33.7
40.7
5,400
5,200
11,200
10,800
10,400
16,100
15,600
21,500
20,800
26,900
26,000
31,200
36,400
3.5
3.5
7.0
7.0
7.0
10.5
10.5
14.0
14.0
17.5
17.5
21.0
24.5
HNQD04A016
HNQD04A021
HNQD04A023
HNQD06A031
HNQD06A034
HNQD08A041
HNQD08A046
HNQD10A052
HNQD10A057
HNQD12A069
HNQD14A083
16.0
20.7
22.9
31.0
34.4
41.4
45.8
51.8
57.3
68.7
83.1
15.6
20.3
22.4
30.4
33.7
40.6
44.9
50.7
56.1
67.3
81.5
22,300
21,500
20,800
32,300
31,200
43,000
41,600
53,700
52,100
62,500
72,900
14.0
14.0
14.0
21.0
21.0
28.0
28.0
35.0
35.0
42.0
49.0
460/3/60
Single Row
1.8
1.8
3.5
3.5
3.5
5.3
5.3
7.0
7.0
8.8
8.8
10.5
12.3
Double Row
7.0
7.0
7.0
10.5
10.5
14.0
14.0
17.5
17.5
21.0
24.5
Maximum No.
of Feeds
Connections
(in.)
Refrigerant
Summer Charge
R-22 (lbs.)
Approx.
Net Wt.
(lbs.)
7
14
14
21
28
21
28
21
28
21
28
28
28
1-3/8
1-3/8
1-3/8
1-5/8
2-1/8
2-1/8
2-1/8
2-1/8
2-5/8
2-5/8
2-5/8
2-5/8
(2) 2-5/8
8
10
10
15
29
22
30
51
70
64
86
102
118
330
360
580
630
680
930
1,000
1,210
1,310
1,510
1,640
1,950
2,240
28
42
56
42
56
42
56
42
56
56
56
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(4)
19
29
40
44
58
104
140
125
172
201
236
1,240
1,340
1,440
1,990
2,140
2,630
2,830
3,290
3,540
4,230
4,910
1-3/8
1-5/8
2-1/8
2-1/8
2-1/8
2-1/8
2-5/8
2-5/8
2-5/8
2-5/8
2-5/8
830 Series Model HNX, 830 RPM, 1.0 HP, 30" Fan Diameter
HNX
Model
THR, MBH/1°F TD
R-22
R-404A
HNXS01A006
HNXS01A008
HNXS02A010
HNXS02A013
HNXS02A015
HNXS03A020
HNXS03A023
HNXS04A026
HNXS04A030
HNXS05A033
HNXS05A038
HNXS06A045
HNXS07A052
6.4
7.5
9.8
13.1
15.1
19.7
22.7
26.3
30.3
32.8
37.8
45.4
52.0
6.2
7.4
9.6
12.8
14.8
19.3
22.3
25.7
29.7
32.1
37.1
44.5
51.0
7,600
7,300
15,900
15,200
14,700
22,900
22,000
29,800
28,400
37,300
35,500
42,600
49,700
4.8
4.8
9.6
9.6
9.6
14.4
14.4
19.2
19.2
24.0
24.0
28.8
33.6
HNXD04A020
HNXD04A026
HNXD04A030
HNXD06A039
HNXD06A045
HNXD08A052
HNXD08A061
HNXD10A066
HNXD10A076
HNXD12A091
HNXD14A104
19.6
26.2
30.3
39.4
45.4
52.5
60.6
65.6
75.7
90.8
104.1
19.2
25.7
29.7
38.6
44.5
51.4
59.3
64.3
74.2
89.0
102.0
31,700
30,500
29,300
45,700
44,000
59,700
56,800
74,600
71,000
85,200
99,400
19.2
19.2
19.2
28.8
28.8
38.4
38.4
48.0
48.0
57.6
67.2
26
Total FLA
CFM
230/3/60
460/3/60
Single Row
2.4
2.4
4.8
4.8
4.8
7.2
7.2
9.6
9.6
12.0
12.0
14.4
16.8
Double Row
9.6
9.6
9.6
14.4
14.4
19.2
19.2
24.0
24.0
28.8
33.6
Maximum No.
of Feeds
Connections
(in.)
Refrigerant
Summer Charge
R-22 (lbs.)
Approx.
Net Wt.
(lbs.)
7
14
14
21
28
21
28
21
28
21
28
28
28
1-3/8
1-3/8
1-3/8
1-5/8
2-1/8
2-1/8
2-1/8
2-1/8
2-5/8
2-5/8
2-5/8
2-5/8
(2) 2-5/8
8
10
10
15
29
22
30
51
70
64
86
102
118
330
360
580
630
680
930
1,000
1,210
1,310
1,510
1,640
1,950
2,240
28
42
56
42
56
42
56
42
56
56
56
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(4)
19
29
40
44
58
104
140
125
172
201
236
1,240
1,340
1,440
1,990
2,140
2,630
2,830
3,290
3,540
4,230
4,910
1-3/8
1-5/8
2-1/8
2-1/8
2-1/8
2-1/8
2-5/8
2-5/8
2-5/8
2-5/8
2-5/8
830 Series Model HNL, 830 RPM, 1.5 HP, 30" Fan Diameter
THR, MBH/1°F TD
Total FLA
HNL
Model
R-22
R-404A
HNLS01A007
HNLS01A008
HNLS02A010
HNLS02A014
HNLS02A016
HNLS03A021
HNLS03A024
HNLS04A028
HNLS04A032
HNLS05A035
HNLS05A042
HNLS06A050
HNLS07A055
6.7
8.0
10.1
13.9
16.1
20.9
24.2
27.8
32.3
35.5
41.6
49.9
55.0
6.6
7.8
9.9
13.6
15.8
20.5
23.8
27.3
31.7
34.7
40.8
48.9
53.9
8,400
8,000
17,500
16,700
16,100
25,100
24,100
32,800
31,200
41,000
39,100
46,900
54,700
6.6
6.6
13.2
13.2
13.2
19.8
19.8
26.4
26.4
33.0
33.0
39.6
46.2
HNLD04A020
HNLD04A028
HNLD04A032
HNLD06A042
HNLD06A048
HNLD08A056
HNLD08A065
HNLD10A071
HNLD10A083
HNLD12A100
HNLD14A110
20.2
27.8
32.3
41.8
48.4
55.7
64.6
70.9
83.1
99.8
110.0
19.8
27.3
31.7
40.9
47.5
54.6
63.3
69.5
81.5
97.8
107.9
35,000
33,500
32,100
50,200
48,200
65,600
62,500
82,000
78,100
93,700
109,300
26.4
26.4
26.4
39.6
39.6
52.8
52.8
66.0
66.0
79.2
92.4
CFM
Maximum No.
of Feeds
230/3/60 460/3/60 575/3/60
Single Row
3.3
3.3
6.6
6.6
6.6
9.9
9.9
13.2
13.2
16.5
16.5
19.8
23.1
Double Row
13.2
13.2
13.2
19.8
19.8
26.4
26.4
33.8
33.0
39.6
46.2
Connections
(in.)
Refrigerant
Summer
Charge
R-22 (lbs.)
Approx.
Net Wt.
(lbs.)
2.6
2.6
5.2
5.2
5.2
7.8
7.8
10.4
10.4
13.0
13.0
15.6
18.2
7
14
14
21
28
21
28
21
28
21
28
28
28
1-3/8
1-3/8
1-3/8
1-5/8
2-1/8
2-1/8
2-1/8
2-1/8
2-5/8
2-5/8
2-5/8
2-5/8
(2) 2-5/8
8
10
10
15
29
22
30
51
70
64
86
102
118
330
360
580
630
680
930
1,000
1,210
1,310
1,510
1,640
1,950
2,240
10.4
10.4
10.4
15.6
15.6
20.8
20.8
26.0
26.0
31.2
36.4
28
42
28
56
56
42
56
42
56
56
56
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(4)
19
29
40
44
58
104
140
125
172
201
236
1,240
1,340
1,440
1,990
2,140
2,630
2,830
3,290
3,540
4,230
4,910
Connections
(in.)
Refrigerant
Summer
Charge
R-22 (lbs.)
Approx.
Net Wt.
(lbs.)
1-3/8
1-5/8
2-1/8
2-1/8
2-1/8
2-1/8
2-5/8
2-5/8
2-5/8
2-5/8
2-5/8
1140 Series Model HNH, 1140 RPM, 1.5 HP, 30" Fan Diameter
THR, MBH/1°F TD
Total FLA
HNH
Model
R-22
R-404A
HNHS01A007
HNHS01A009
HNHS02A011
HNHS02A015
HNHS02A017
HNHS03A022
HNHS03A026
HNHS04A029
HNHS04A034
HNHS05A037
HNHS05A044
HNHS06A053
HNHS07A061
7.3
8.7
10.7
14.5
17.1
21.8
25.7
29.1
34.2
37.1
44.0
52.8
61.0
7.2
8.6
10.5
14.2
16.7
21.4
25.2
28.5
33.5
36.4
43.1
51.7
59.8
9,900
9,500
20,500
19,800
19,000
29,700
28,500
38,600
37,000
48,300
46,200
55,400
64,700
7.0
7.0
14.0
14.0
14.0
21.0
21.0
28.0
28.0
35.0
35.0
42.0
49.0
HNHD04A021
HNHD04A029
HNHD04A034
HNHD06A044
HNHD06A051
HNHD08A058
HNHD08A068
HNHD10A074
HNHD10A088
HNHD12A106
HNHD14A122
21.4
29.1
34.2
43.6
51.3
58.2
68.4
74.2
88.0
105.6
121.9
21.0
28.5
33.5
42.8
50.3
57.0
67.1
72.7
86.2
103.5
119.5
41,000
39,600
38,100
59,400
57,100
77,200
73,900
96,500
92,400
110,900
129,400
28.0
28.0
28.0
42.0
42.0
56.0
56.0
70.0
70.0
84.0
98.0
CFM
Maximum No.
of Feeds
208/3/60 460/3/60 575/3/60
Single Row
3.5
3.5
7.0
7.0
7.0
10.5
10.5
14.0
14.0
14.0
17.5
17.5
21.0
Double Row
24.5
14.0
14.0
21.0
21.0
28.0
28.0
35.0
35.0
42.0
49.0
2.8
2.8
5.6
5.6
5.6
8.4
8.4
11.2
11.2
14.0
14.0
16.8
19.6
7
14
14
21
28
21
28
21
28
21
28
28
28
1-3/8
1-3/8
1-3/8
1-5/8
2-1/8
2-1/8
2-1/8
2-1/8
2-5/8
2-5/8
2-5/8
2-5/8
(2) 2-5/8
8
10
10
15
29
22
30
51
70
64
86
102
118
330
360
580
630
680
930
1,000
1,210
1,310
1,510
1,640
1,950
2,240
11.2
11.2
11.2
16.8
16.8
22.4
22.4
28.0
28.0
33.6
39.2
28
42
56
42
56
42
56
42
56
56
56
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(4)
19
29
40
44
58
104
140
125
172
201
236
1,240
1,340
1,440
1,990
2,140
2,630
2,830
3,290
3,540
4,230
4,910
1-3/8
1-5/8
2-1/8
2-1/8
2-1/8
2-1/8
2-5/8
2-5/8
2-5/8
2-5/8
2-5/8
27
Fluid Coolers
Direct-Drive Fluid Coolers
Model WGS (vertical or horizontal air flow available) and HFS (available in vertical air flow only) direct-drive
fluid coolers are easy to install and maintain, yet are ruggedly designed to handle all applications. Available
in a variety of sizes, the WGS and HFS units have design features ideal for the commercial/industrial locations.
Specifically engineered for outdoor installations, the cabinet is constructed of heavy gauge aluminum or
prepainted galvanized steel to resist corrosion in all climates Additional design features include:
• Fully baffled fan sections to prevent windmilling
• Single-point wiring to junction box
• Balanced fans, featuring heavy gauge aluminum blades riveted to plated steel spiders
Model WGS
WGS
Model
CFM
WGS049
WGS080
WGS107
WGS123
WGS147
WGS165
WGS211
WGS225
WGS248
5,050
6,450
10,100
12,400
13,700
12,900
20,500
19,900
19,400
Vol.
in
Gal.
3
4
4
4
5
6
7
7
9
Base Capacity Range 1°F TD,
40% Glycol (130° Average Temp.)
Minimum
Maximum
GPM MBH PD/F GPM MBH PD/F
10
2.23
4.7
30
2.97
15.5
10
3.07
7.4
60
4.62
13.0
10
3.46
7.5
60
6.10
28.2
10
3.62
7.5
60
6.88
28.2
10
3.92
9.4
50
7.64
25.2
10
4.17
12.4
60
8.70
20.9
15
5.93
12.3
120 12.31 25.7
20
6.99
6.8
120 12.94 25.7
20
7.65
12.9
160 14.08 25.7
Motor
Qty.
HP
1
1
2
2
2
2
3
3
3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
Dimensions (in.)
208-230V
L
3 Ph.
2.6
40
2.6
50
5.2
70
5.2
70
5.2
90
2.5
90
7.8
130
7.8
130
7.8
130
H
D
40-1/2
40-1/2
40-1/2
40-1/2
40-1/2
40-1/2
40-1/2
40-1/2
40-1/2
43
43
43
43
43
43
43
43
43
Connections (in.) Approx.
Dry
Net Wt.
Inlet
Outlet
(lbs.)
1-3/8
1-3/8
180
1-5/8
1-5/8
260
2-1/8
2-1/8
450
2-1/8
2-1/8
470
2-1/8
2-1/8
510
2-1/8
2-1/8
530
2-5/8
2-5/8
550
2-5/8
2-5/8
580
2-5/8
2-5/8
625
*Motors also available in 208-230/1, 460/3
Model HFS
HFS
Model
CFM
Operating
Charge
(Gal.)
HFS113
HFS133
HFS149
HFS175
HFS199
HFS223
HFS247
HFS265
HFS297
HFS331
HFS351
HFS377
HFS401
HFS443
HFS481
HFS583
19,780
19,800
19,110
18,340
29,700
28,660
28,070
38,600
37,250
38,020
35,710
46,610
46,200
44,580
55,400
53,460
6.6
9.0
9.0
11.6
12.8
12.8
16.4
16.4
16.4
21.3
21.3
20.0
26.1
26.1
31.0
31.0
HFS226
39,570
13.3
HFS266
39,600
18.2
HFS298
38,210
18.2
HFS330
37,530
23.1
HFS350
36,770
23.1
HFS398
59,400
25.4
HFS428
58,510
25.4
HFS448
57,320
25.4
HFS496
56,240
32.8
HFS532
77,200
32.7
HFS596
74,500
32.7
HFS660
72,790
42.5
HFS700
71,310
42.5
HFS754
93,120
40.0
HFS804
92,400
52.1
HFS842
91,010
52.1
HFS888
89,170
52.1
HFS964
110,900
62.0
HFS986
109,240
62.0
HFS998
107,020
62.0
†
Does not include operating charge
28
Base Capacity Range @ 1°F TD 40%
Motor (Total FLA)
Glycol (130° Average Temp.)
Minimum
Maximum
208575/
Qty.
HP
230/3/60 3/60
GPM MBH PD/F GPM MBH PD/F
Single Row
20
6.4
3.2 120 11.69 10.7
2
1-1/2
14.0
5.6
20 7.01 4.8 180 13.34 10.7
2
1-1/2
14.0
5.6
20 7.42 4.8 180 14.89 10.7
2
1-1/2
14.0
5.6
30 10.2 6.6 240 16.79 10.7
2
1-1/2
14.0
5.6
20 8.19 7.0 180 19.40 15.7
3
1-1/2
21.0
8.4
30 11.62 14.3 180 21.66 15.7
3
1-1/2
21.0
8.4
30 11.92 9.5 240 23.74 15.7
3
1-1/2
21.0
8.4
20 8.71 9.2 180 25.09 20.8
4
1-1/2
28.0
11.2
30 12.34 6.1 180 27.93 20.8
4
1-1/2
28.0
11.2
30 12.88 12.5 240 30.89 20.8
4
1-1/2
28.0
11.2
30 13.04 12.5 240 32.13 20.8
4
1-1/2
28.0
11.2
30 12.97 7.5 180 33.69 25.8
5
1-1/2
35.0
14.0
30 13.20 15.4 240 35.89 25.8
5
1-1/2
35.0
14.0
30 13.40 15.4 240 39.12 25.8
5
1-1/2
35.0
14.0
40 17.22 8.9 220 41.02 26.4
6
1-1/2
42.0
16.8
40 17.59 8.9 220 44.66 26.4
6
1-1/2
42.0
16.8
Double Row
30 11.24 6.6 240 23.38 10.7
4
1-1/2
28.0
11.2
40 14.03 4.8 350 26.56 10.2
4
1-1/2
28.0
11.2
40 14.84 4.8 350 29.65 10.2
4
1-1/2
28.0
11.2
50 17.77 4.8 500 32.53 11.5
4
1-1/2
28.0
11.2
50 18.21 4.8 500 33.80 11.5
4
1-1/2
28.0
11.2
40 16.38 7.0 350 38.66 15.0
6
1-1/2
42.0
16.8
40 16.69 7.0 350 40.99 15.0
6
1-1/2
42.0
16.8
40 16.93 7.0 350 43.06 15.0
6
1-1/2
42.0
16.8
50 20.73 6.9 500 47.77 16.9
6
1-1/2
42.0
16.8
40 17.42 9.2 350 49.87 19.8
8
1-1/2
56.0
22.4
40 17.74 9.2 350 55.46 19.8
8
1-1/2
56.0
22.4
50 21.96 9.0 500 62.24 22.3
8
1-1/2
56.0
22.4
50 22.13 9.0 500 64.74 22.3
8
1-1/2
56.0
22.4
60 25.94 7.5 350 66.82 24.5 10 1-1/2
70.0
28.0
50 22.23 11.2 500 72.42 27.7 10 1-1/2
70.0
28.0
50 22.45 11.2 500 75.91 27.7 10 1-1/2
70.0
28.0
80 34.06 7.5 500 78.96 27.7 10 1-1/2
70.0
28.0
80 34.44 8.9 500 84.70 33.1 12 1-1/2
84.0
33.6
80 34.86 8.9 500 88.78 33.1 12 1-1/2
84.0
33.6
80 35.17 8.9 500 92.33 33.1 12 1-1/2
84.0
33.6
Dimensions (in.)
460/
3/60
L
H
D
Approx.
Net Wt.
(lbs.)†
7.0
7.0
7.0
7.0
10.5
10.5
10.5
14.0
14.0
14.0
14.0
17.5
17.5
17.5
21.0
21.0
127
127
127
127
180
180
180
233
233
233
233
286
286
286
339
339
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
45-1/2
45-1/2
45-1/2
45-1/2
45-1/2
45-1/2
45-1/2
45-1/2
45-1/2
45-1/2
45-1/2
45-1/2
45-1/2
45-1/2
45-1/2
45-1/2
720
760
780
860
1,170
1,190
1,220
1,550
1,590
1,620
1,730
1,960
1,960
2,200
2,350
2,580
14.0
14.0
14.0
14.0
14.0
21.0
21.0
21.0
21.0
28.0
28.0
28.0
28.0
35.0
35.0
35.0
35.0
42.0
42.0
42.0
127
127
127
127
127
180
180
180
180
233
233
233
233
286
286
286
286
339
339
339
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
88
88
88
88
88
88
88
88
88
88
88
88
88
88
88
88
88
88
88
88
1,560
1,600
1,650
1,670
1,780
2,350
2,400
2,500
2,560
3,080
3,140
3,190
3,450
3,920
3,930
4,070
4,300
4,620
4,800
5,130
Refrigeration Controls and Technology
Beacon II™ Refrigeration System is Chandler’s patented, pre-assembled, factory-installed
refrigeration system featuring an integrated microcomputer-based electronic control board. Beacon II™
offers:
• Complete factory installation, wiring and testing, saving time and money
• Simplified field electrical connections and 24 volt wiring between condenser and evaporator coil
• Preset factory superheat allows the system to run more efficiently and reduces future adjustments
• Monitors and controls box temperature, evaporator superheat, system status and defrost
• Monitor and make system changes remotely via modem with exclusive Beacon II™ Smart II software
with Beacon II™ Smart Controller
• Data-logging capabilities with Smart Controller
™
Beacon II™ Smart Controller allows you to monitor and make changes to the refrigeration system
via modem connection from anywhere in the world. One Smart Controller can program and control up to
four condensing units with up to four evaporators on each system.
The patented Beacon II™ Smart Defrost system available with Beacon II™ Smart Controller can
reduce the number of system defrost by 75 percent on average, greatly reducing the amount of energy
used and reducing operating costs.
Beacon II™ Smart II Software makes it easy to adjust and monitor one or more refrigeration systems
as well as capture minute-by-minute system conditions. This Windows®-based software allows you to connect
to the Beacon II™ Smart Controller from anywhere in the world to monitor the systems, make adjustments
and log real-time system conditions. This data-logging capability is critical in the food-service industry.
Smart Defrost Kit™ (SDK), available as a factory installed option on condensing units or as an
aftermarket retrofit kit via Interlink Commercial Refrigeration Parts, is a control module that can reduce
the number of defrosts by up to 40% on a typical commercial refrigeration system. This reduces energy
consumption and costs.
29
Additional Products from Chandler
The Mohave advanced hot gas defrost refrigeration system with electronic controller utilizes hot
gas to greatly reduce defrost times and operates in all outdoor ambient temperatures.* This leads
to increased energy efficiency and product integrity in a refrigeration system that can be used
in a greater variety of environmental conditions. This system utilizes a state-of-the-art electronic
defrost controller with a proprietary control scheme that allows the system to continually operate
at its most optimal level.
Condensing Unit
• Integral condenser sub-cooling circuit in condenser for
added capacity and vapor free liquid
• Floating Tube™ condenser coil design
• Electronic defrost controller
• Pressure or ambient fan cycling for head
pressure control
• Electronic pressure regulator for defrost control
• Anti-short cycling protection
• High pressure and low pressure controls
• Oil pressure safety control
• Easily accessible control box
• High efficiency Copeland Discus® compressors with poe oil
• Thermally protected permanently lubricated ball bearing
condenser fan motor(s)
• Receivers are sized for sufficient pumpdown capacity with
inlet and outlet service valves
• Cabinet is constructed from painted galvanized steel
• Replaceable core liquid line filter drier
• Replaceable core suction filter
Evaporators
• All components are factory installed and wired
• Independent or single point power supply from
condensing unit
• 4 and 6 FPI medium and large unit coolers
Features:
•
•
•
•
•
Mounted TXV and distributor nozzle
Mounted check valves
Mounted liquid line solenoid
Mounted suction “P” trap
Electric drain pan heater standard (mounted
hot gas drain loop optional)
• Mounted and wired control contactors
*Tested to -20°F ambient.
Multiple Compressor Condensing Units
The FlexPack™ provides many features that produce outstanding results for both your refrigeration system and your bottom line.
Flexibility for a wide range of applications
• Modular design accommodates up to three compressors
(0.5-6 HP Hermetic or Scroll®)
• System capacity range from 5 – 18 HP (dependent upon
cabinet size)
Durability and Reliability
• 14-gauge galvanized steel frame
• 1-year parts warranty
• 4-year optional compressor warranty
Reduced installation costs and easy serviceability
• Hinged access panels to refrigeration and
electrical components
• Single roof penetration
• Single-point main power
• Clean and intuitive electrical and piping layout
Energy efficiency and reduced noise
• Remote condenser circuits
• Reduces heat load into space resulting in lower air conditioning
energy costs
• Recessed, vertical-discharge, flush-mounted 18" fans with 1100
RPM motors
• Reduces noise levels
30
Clean and uniform appearance
• Painted galvanized steel cabinet
• Small footprint
(QJLQHHUHGSolutions
TM
)URP VWDUW WR ILQLVK
Air Handlers
• Available in sizes 03-75
• Multiple coil types and accessories available to fit specific
application needs
• Engineered and built to fit your unique project requirements
Indoor and Outdoor Racks
•
•
•
•
Available with up to 8 parallel-piped compressors
Can be used with air-cooled, water-cooled or evaporative-cooled condensers
Engineered and built to fit your unique project requirements
ETL-508a listed control panel
Customer Specific Orders
We have a wide range of capabilities and will work with you, from
start to finish, to create a customized solution for your needs. With
Engineered Solutions, we will visualize, design, and realize the
product required for the job.
Contact your sales representative today to get the process started!
31
A Brand of Heatcraft Refrigeration Products, LLC
2175 West Park Place Blvd. • Stone Mountain, GA • 30087
800-321-1881
www.chandlerref.com
CH-CC-0609 | Version 000

refrigeration products - Heatcraft Worldwide Refrigeration

Transcription

Similar documents

PDF Version zum - finsterwalder

Stair Products Catalog

spec sheet - Rodway Refrigeration

LSP full catalog 07-56page.indd

List of Registered Identified Suppliers (RIS) (2015/04/30)

Refrigeration Equipment Price List

Okuma katalógus - Atlantis Fishing Horgászáruház

Fluid Coolers Technical Guide