assembly guide - Virgin Musical Instruments

ASSEMBLY GUIDE
HD-5
Electronic Drum Kit
EASY ASSEMBLY GUIDE
IF YOU HAVE ANY QUESTIONS
CALL OUR TOLL FREE HELPLINE
888-998-9848
DO NOT RETURN TO THE STORE
UNBOXING YOUR DRUM KIT
1. Carefully unpack all contents of box
(1) Crash Cymbal
(1) Ride Cymbal
(1) Sound Module
(1) Hi-Hat Cymbal
(3) Tom Drums
(1) Snare Drum
Kick Drum
Kick Pedal
Hi-Hat Control Pedal
Drum Kit Components
Sound
Module
Cymbals
Drum Frame
Module
Mount
Toms
Kick Drum
Mount
Cymbal Arms
Snare
Kick
Pedal
Feet
Hi-Hat Control Pedal
Kick Drum
Not Pictured:
(1) Labeled Wiring Harness
(1) Pair Headphones
(1) Pair Drumsticks
(1) Drumstick Holder
Velcro Strips
DRUM KIT ASSEMBLY
2. Attach the feet to the Drum Frame (fig.1)
3. Unfold the Drum Frame arms as shown
(fig.2)
(fig.2)
(fig.1)
4. Attach the cymbal arms to the drum frame
indicated positions .(fig.3)
5. Attach the cymbals to the cymbal arms as
shown. Place the fin on the cymbal arm between the flanges on the cymbal as shown.(fig.4)
HI-HAT
CRASH
RIDE
(fig.4)
(fig.3)
DRUM KIT ASSEMBLY (CON’T)
6. Align the holes in Snare Drum Pad and the
7. Attach the Drum Pads in the positions
three Tom Drum Pads and insert them into the hown below. (fig. 5)
pole on the Drum Frame as shown.
TOM
TOM
SNARE
SNARE
(fig.5)
8. Align the holes and attach the screws
with the Drum Sound Module head
and its stand as shown below. (fig. 6)
9. Insert the rod of sound module stand into
the Drum Frame clamp as shown, then tighten.
(fig.7)
BACK
(fig.6)
(fig.7)
DRUM KIT ASSEMBLY (CON’T)
10. Attach the kick drum to the kick drum
brace as shown below. (fig.8)
11. Assemble the kick drum pedal by inserting
the two chrome metal rods into the kick drum
pedal frame as shown below .
(fig.9)
(fig.8)
(fig.9)
12. Attach the kick drum pedal mallet to the
kick drum pedal by insertIng and attaching as
shown below.
(fig.10& 11)
13. Insert the tongue of the kick drum into the clamp of
the kick drum pedal. (fig.12) Tighten clamp on the pedal until the kick drum and pedal are securely fastened.
(fig.13)
(fig.10)
(fig.11)
(fig.12)
(fig.13)
DRUM KIT ASSEMBLY (CON’T)
14. Check the surface pads on the bottom of the
hi-hat control pedal. The pads may be used on
either carpet or hard flooring. (fig.14)
15. Place the hi-hat control pedal on the
ground by the hi-hat cymbal. (fig.15)
(fig. 14)
CARPET
PEEL
HARD FLOORING
(fig. 15)
DRUM KIT WIRING DIAGRAM
16. Connect the wiring harness to the interface at the bottom of the drum sound module, then
connect the labeled cables to their corresponding drum pads, cymbals and pedals, as show
below.
Drum Module Connector Panel
POWER
OFF ON
control module
DC 9V
USB
TRIGGER
HEADPHONE
LINE OUT LINE IN
ride
tom 3
tom 2
tom 1
POWER
OFF ON
USB
DC 9V
TRIGGER
HEADPHONE
crash
LINE OUT LINE IN
plug into “trigger”
hi-hat
cable snake
to drumset
snare
high-hat control
kick
DRUM THRONE ASSEMBLY
17. Extend the drum throne legs and secure the legs with the wingut. (fig 16) Fasten the drum
throne stool to the height adjustment rod and secure the stool with the wingnut. (fig 17) Set
up the drum throne at the desired height as shown below. (fig 18)
(fig. 18)
(fig. 16)
13)
(fig. 17)
FINAL STEPS
18. Attach Drumstick Pouch (fig 19) to drum frame as shown. (fig 20)
(fig 20)
(fig 19)
19. Please use the included Velcro Strips to attach
the wiring harness to the drum frame. This will
help to make the wiring harness neat and orderly
against the drum frame.
velcro
20. Attach the included power supply adapter
and the headphones to drum sound module
connector panel.
POWER
OFF ON
DC 9V
drum frame
USB
TRIGGER
HEADPHONE
LINE OUT LINE IN
If you have any questions about your drum kit
please contact us toll free
888-998-9848
Virgin (VMI) is the Parent Company of Hitman Drums
Virgin Musical Instrument Company
PO BOX 2908
LA MESA, CA 91943
[email protected]
www.virginmusicalinstruments.com