KREBS® Products for the COAL INDUSTRY

KREBS® Products for the
COAL INDUSTRY
KREBS® Hydrocyclones, millMAX® Pumps,
and TechnequipTM Valves for Coal Processing
2
KREBS® Products
for the Coal Processing Industry
Contents
??
Introduction...................2
??
millMAX Pump........................3
??
Technical Specifications..........4
??
millMAX-e Pump ....................6
??
gravelMAX Pump ..................7
??
Heavy Media Cyclones ............8
??
Coal Classifying Cyclones ......11
??
Water Only Hydrocyclones....13
??
Ceramic Liners ......................15
??
DeSlime Cyclones...................17
??
Coal Spirals............................18
??
Technequip Valves ................20
FLSmidth Krebs is a global leader in high efficiency process equipment for
coal separation systems. For more than 60 years, Krebs has helped
advance the productivity of coal processing operations and provided
innovations for greater production, efficiency and reliability.
FLSmidth Krebs continues to improve our designs and materials of our
equipment using long-lasting urethane and ceramic components.
FLSmidth Krebs Hydrocyclones provide you with the separation
performance you need using leading technology.
FLSmidth Krebs millMAX Pumps provide increased wear life with
on-line wear adjustment along with higher efficiencies resulting in power
and cost savings.
FLSmidth Krebs Coal Spirals advanced design provide high capacity
with recessed cutter position and enhanced separation, reducing product
misplacement.
FLSmidth Krebs Technequip Knife Gate Valves provide reliable, long
wear life and a 100% bubble tight seal for fine coal slurries.
3
KREBS® millMAXTM pump
for Coal Applications
Did you know
All of our horizontal millMAX™ pumps feature a
patented on-line wear clearance adjustment, to
minimize wear.
The reduction of solids recirculation reduces size
degradation and wear. millMAX™ Pumps maintain
constant flow and discharge pressure, without
increasing speed and/or the chance of motor overload.
Benefits:
•
•
•
•
Increased Service Life
Reduce Power Consumption
More Consistent Hydrocyclone Performance
Extended Bearing Life
Applications:
•
•
•
•
Heavy Media Feed
Dilute Media
Classifying Cyclone Feed
Thickener Underflow/ Slurry Line
Size Range (in)
Metric (mm)
3x2
80
4x3
100
6x4
150
8x6
200
10 x 8
250
12 x 10
300
14 x 12
350
16 x 14
400
18 x 16
450
20 x 18
500
24 x 20
600
28 x 26
700
54
Technical - Specifications
Title
The Krebs millMAX™ pump
design includes the following:
Title
Casing -
designed for minimum slurry
turbulence
• Bulletsand even wear. Includes
integral wear ring, carrier, and adjustment
• Bullets
screws
for on-line adjustment and
elimination of suction side recirculation.
millMAX™ Power Frame
• Heavy duty cast pedestal
• External bearing assembly
adjustment
• Wide bearing centers
• Heavy duty shaft and bearings
• Double clamp
High Performance Centrifugal
Gland Seal
•
•
Large expeller diameter
generates high suction level
sealing capacity
Zero leakage while operating
Wear Ring - adjustable wear ring
assembly to minimize suction side
impeller clearance during operation.
Impeller - designed for high slurry
efficiency and hydraulic performance.
Machined surface at the eye for wear ring
adjustment.
Suction Liner - with integral wear ring
(14x12 and larger). Matching full impeller
diameter and profile for close operating
clearance.
Wear Parts - designed hydraulically to
wear evenly. Constructed of high-chrome
/white iron at 650/720 Brinell hardness.
Power Frame - heavy duty cast iron
pedestal with external bearing assembly
adjustment. Drilled for overhead motor
mounting option.
Flanges - intake and discharge flanges
Reverse Taper Roller Bearings
• Increases effective load span to
improve life
• Main bearing failure may be due
to over greasing, but pumping
action of taper rollers discharges
grease to the outside, preventing
ingress of slurry and over
greasing of bearing cartridge
Water Flush Gland
designed to suit various piping requirements.
Required flow rate for a water flush
seal at 10 psig (68.9 kPa)above pump
discharge pressure
Power
Frame
Full
Flow
(gpm)
Full
Flow
(m3/h)
Low
Flow
(gpm)
Low
Flow
(m3/h)
MMAA
8.0
1.8
1.0
0.2
MMA
15.0
3.4
2.0
0.5
MMB
20.0
4.5
3.0
0.7
MMC
25.0
5.7
4.0
0.9
MMD
30.0
6.8
5.0
1.1
MME
55.0
12.5
N/A
N/A
MMF
85.0
19.3
N/A
N/A
Bearing Assembly - heavy duty
high-tensile steel shaft and indirect fitted
taper roller bearings rated at 100,000 hrs
B-10 life minimum.
FULL FLOW
LOW FLOW
12
5
Title
High Radial Vanes
• Clears large solids
• Prevents solids from being
crushed
• Reduces pressure at the
eye of the impeller
External Jacking
Screws
• Four screws for
on-line clearance
adjustment
• Adjusted while the
pump is operating
• Adjusted six to
eight times during
the life of the wet
end
Adjustable
Wear Ring
• Wear ring takes
up clearance at
the impeller
• Adjusted during
operation
• Reduces suction
side recirculation
• Maintain
hydraulic
performance
Wide Clearance
• Dramatic reduction in
crushing of solids
• Increased wear life
• Reduce power consumption
Narrow Clearance
Reduces pressure at gland to assist
centrifugal dry gland seal or reduce
gland water pressure.
driMAX™ Mechanical Seal
• Operates in extreme abrasive
environment
• Clearance adjustment can be
made without moving seal
96
KREBS® millMAX-eTM pump
Title
for Coal Applications
Did you know
Reverse taper roller bearings:
The millMAX-e™ pump is the most efficient slurry
pump in its class. It saves power and saves money;
thus, minimizing total cost of ownership. The extremely
efficient design often allows for smaller motors to be
used.
• Bullets
•
•
millMAX-e
•
Bullets design incorporates an integrated power
frame and bearing assembly, eliminating the need to
Wide capacity range
Title
adjust the impeller within the casing. The millMAX-e
power frames utilize the same bearing and shaft
components as the equivalent millMAX power frames
to handle applications with high speed and power
requirements.
Benefits:
•
•
Decreased total weight of the wet end reducing
capital cost
Regional / Service Centers /Parts Stocking
Special Features:
The new adjustment lock nut design compresses the
wear ring carrier to provide an atmospheric seal and
locks the jacking screw in place.
Size Range
(in)
Metric
(mm)
2 x 1.5
50
3x2
80
4x3
100
6x4
150
8x6
200
10 x 8
250
12 x 10
300
14 x 12
350
16 x 14
400
•
Increases effective load span to improve B10 life
Bearing failure may be due to over greasing but
pumping action of taper rollers discharges grease
to the outside, preventing ingress of slurry or over
greasing of bearing cartridge
FLSmidth Krebs offers the millMAX-e pump in
suction sizes of 2 to 16 inches (50 to 400 mm),
providing a wide range of capacity.
High efficiency impeller
•
•
•
Increased efficiencies
Increased service life
Increased head
Required Flow rate for a water flush seal at 10
psig (69 kPa) above pump discharge pressure
Power
Frame
High
Flow
(gpm)
High
Flow
(m3/h)
Low
Flow
(gpm)
Low
Flow
(m3/h)
EMAAA
2.5
0.57
0.5
0.11
EMAA
8
1.82
1
0.23
EMA
15
3.41
2
0.45
EMB
20
4.54
3
0.68
716
KREBS® gravelMAXTM pump
Title
for Coal Applications
Did you know
Adjustable Wear Ring
The gravelMAX Pump is a unique design developed for
passing large particles within abrasive slurries. Excellent
for Heavy Media Cyclone Feed applications.
•
•
•
Krebs millMAX™ pumps, treat the cause of pump wear
and loss of efficiency by virtue of improved hydraulic
design and not with high-price materials of
construction.
Allows a higher density slurries to be pumped
Reduces suction side recirculation
Maintain hydraulic performance
millMAX™ Power Frame
•
•
•
•
Heavy duty cast pedestal
External bearing assembly adjustment
Wide bearing centers
Heavy duty shaft and bearings
Features
•
•
Like other millMAX pump designs, the gravelMAX
pump features a patented on-line clearance
adjustment
Much more robust wet-end components
Benefits
•
•
•
•
•
Pump larger solids
Maintain cyclone pressure longer
Reduce the cost per ton
Adjust pump while running
Longer service life
Reverse Taper Roller Bearings
•
•
Increases effective load span to improve B10 life
Bearing failure may be due to over greasing, but
pumping action of taper rollers discharges grease
to the outside, preventing ingress of slurry or over
greasing of bearing cartridge
Size Range (in)
Metric (mm)
6x4
150
8x6
200
10 x 8
250
12 x 10
300
14 x 12
350
138
KREBS® Heavy Media Cyclones
Title
Did you know
The Heavy Media Cyclone used in the coal industry is an
extremely efficient coal cleaning device using finely
ground (-325 mesh / 44 microns) magnetite and water
as the “media”.
Title
Krebs Heavy Media Cyclones are designed specifically to
• Bullets
clean coal. A gravimetric separation takes place due to
the buoyancy effect of the media forcing the lighter
• Bullets
solids to the center of the cyclone where they are
transported upward and through the vortex finder. The
dense mineral matter spirals downward and through
the apex.
Krebs Heavy Media Cyclones are usually operated in a
near-horizontal orientation allowing for large apex sizes
to be used for refuse removal.
The media density primarily determines separating
gravity. Pressure should be kept relatively low to reduce
classification effects.
Benefits and Features
Krebs large-diameter Heavy Media Cyclones allow
larger top-size to be efficiently cleaned at higher feed
rates.
Cyclones 30” diameter and larger utilize a proprietary
ceramic “acceleration wedge” to modify capacity and
G-forces. Insert a smaller wedge and more capacity is
immediately obtained. Insert a larger wedge when
higher G-forces are required to clean fine coal more
efficiently.
Performance
One of the most important features of a Heavy Media
Cyclone is its high efficiency. Krebs has taken several
design features of the D26B, that has long been
established as the industry’s standard high capacity
cyclone with “benchmark” efficiencies, and
incorporated them into the new larger diameter
designs.
Heavy Media cyclones can handle feed particle top-size
range up to 4” and have capacities from 85 to
985 STPH per cyclone.
918
KREBS® Pre-Engineered Tile Lining in
Title Media Cyclones
Heavy
Tile Lined Heavy Media Cyclones:
Each ceramic tile is machined in the green state
and then fired to become an interlocking,
serialized component.
Although this process is relatively expensive,
the increased wear life that results is one
reason why Krebs Heavy Media Cyclones are
chosen over others that utilize flat tile.
Pre-Engineered tiles can come in two different
grades. They are used on FLSmidth inlet heads
to maximize service life.
After assembly of tile lined sections, all
cyclones are thoroughly inspected before
painting.
Krebs provides several ceramic tile lining
options with 1” to 1.5” thickness to optimize
wear life.
Pre-engineered ceramic tile resulting in very high wear life for Heavy Media Cyclones
10
19
KREBS® Heavy Media Cyclones
Title
KREBS Heavy Media Cyclones - Typical Operating Parameters (U.S. Units)
Krebs Model
Designation
Feed Particle
Maximum Size
Dry Feed Capacity*
(stph)
Pulp Flowrate
Range (gpm)
Head Equivalent
(ft)
D20LSB
Title
3/4”
85
1,050
15
• Bullets
D26B
1 1/2”
150
1,910
20
CoalMAX26
• Bullets
1 1/2”
160
2,045
20
D263B
1 1/2”
165
2,065
20
D30B
2”
225
2,830
23
D33T154
2 1/2”
290
3,650
25
D33T214
2 1/2”
315
3,930
25
D40B
3”
460
5,760
30
D44B-A
3”
475
5,940
33
D44B-U
3”
580
7,280
33
D48B
3 1/2”
725
9,100
36
D55B
4”
985
12,300
41
* Based on a 4:1 media-to-coal ratio
* These capacities represent maximums for units fitted with the largest inlet and vortex finder
KREBS Heavy Media Cyclones - Typical Operating Parameters (Metric Units)
Krebs Model
Designation
Feed Particle
Maximum Size
Dry Feed Capacity*
(mtph)
Pulp Flowrate
Range (m3/h)
Head Equivalent
(meters)
D20LSB
19mm
77
238
4.6
D26B
38mm
136
434
6.1
CoalMAX26
38mm
145
464
6.1
D263B
38mm
150
469
6.0
D30B
51mm
205
643
7.0
D33T154
63mm
264
829
7.6
D33T214
63mm
286
892
7.6
D40B
76mm
418
1308
9.2
D44B-A
76mm
432
1348
10.1
D44B-U
76mm
527
1653
10.1
D48B
89mm
659
2066
11.0
D55B
102mm
895
2792
12.6
* Based on a 4:1 media-to-coal ratio
* These capacities represent maximums for units fitted with the largest inlet and vortex finder
Consult a Krebs Sales Engineer for sizing needs. Visit our website: www.flsmidthkrebs.com
11
20
KREBS gMAX® Coal Classifying Cyclones
Title
Did you know
Benefits and Features
The Krebs gMAX is our newest generation of cyclone,
re-engineered from apex to vortex finder. The Krebs
gMAX cyclone has the capability to produce finer and
sharper separations using high-capacity designs.
• Minimized coarse solids misplacement to overflow
The Krebs gMAX inlet has been improved upon over
the Krebs involute feed inlet that had been the stateof-the-art for over 40 years. The outer wall involute
entrance design pre-classifies the feed solids prior to
entering the main body of the cyclone. The gMAX also
includes an improved vortex finder design.
• Operates at higher feed rates with the same
separation size achieved
Reduced turbulence within the inlet head results in less
misplacement of coarse material to overflow and
dramatically increases wear life. This longer service life
for the gMAX, due to premium cast ceramics in the
cyclone, will greatly increase the time between cyclone
repair / rebuilds.
To eliminate corrosion of the cyclone housings ceramic
liners are now encased in rigid polyurethane,
completely eliminating the need for steel housings.
• Extended wear life of liners
• Fewer cyclones required for optimal performance
• Can be retrofitted into existing installations to
boost throughput and /or produce finer
separations
• Cone angles: 10.5 or 20 degrees available
Performance
• gMAX classifying cyclones can handle 1/2” (13mm)
top-size
• Capacities up to 50 STPH (45MTPH) per cyclone
• Feed Density up to 15% solids maximum;
underflow density of 40-50% solids are normal
for raw coal applications
gMAX hydrocyclones are available in sizes ranging 6” to 20” diameter with up to 1” thick replaceable liners.
12
17
KREBS gMAX® Coal Classifying Cyclones
Title
Title
• Bullets
• Bullets
KREBS gMAX Coal Classifying Cyclones - Typical Operating Parameters (U.S. Units)
Maximum Feed
Percent Solids
Krebs Model
Designation
Feed Particle
Maximum
Size
Effective Mesh
of Separation
Dry Feed
Range **
(stph))
Pulp FlowRate Range*
(gpm)
Pressure
Drop Range
(psi)
WT%
VOL %
gMAX6BU
28 Mesh
200/270 Mesh
3-6
95-230
25-30
5%
3.5%
gMAX10-10
1/8”.
150/200 Mesh
7-12
275-455
15-25
7%
4.5%
gMAX12LB-10
1/4”
100/150 Mesh
12-19
475-750
15-25
10%
7%
gMAX15LB-20
1/2”
100/150 Mesh
17-28
650-1060
15-25
12%
8%
gMAX15LB-10
1/2”
100/150 Mesh
20-31
785-1200
15-25
13%
8%
gMAX20LB-10
1/2”
65/100 Mesh
30-49
1155-1900
15-20
15%
11%
*Maximum flowrate based on units fitted with the largest inlet and vortex finder.
** Based on 10% feed solids by weight / and dry s.g. of 1.6
KREBS gMAX Coal Classifying Cyclones - Typical Operating Parameters (Metric Units)
Maximum Feed
Percent Solids
Krebs Model
Designation
Feed Particle
Maximum
Size
Effective Mesh
of Separation
Dry Feed
Range **
(mtph))
Pulp FlowRate Range*
(m3/h)
Pressure
Drop Range
(kPa)
WT%
VOL %
gMAX6BU
28 Mesh
200/270 Mesh
3-5
22-52
138-207
5%
3.5%
gMAX10-10
3mm
150/200 Mesh
6-11
62-103
103-172
7%
4.5%
gMAX12LB-10
6mm
100/150 Mesh
11-17
108-170
103-172
10%
7%
gMAX15LB-20
13mm
100/150 Mesh
15-25
148-241
103-172
12%
8%
gMAX15LB-10
13mm
100/150 Mesh
18-28
178-273
103-172
13%
8%
gMAX20LB-10
13mm
65/100 Mesh
27-45
262-432
103-138
15%
11%
*Maximum flowrate based on units fitted with the largest inlet and vortex finder.
** Based on 10% feed solids by weight / and dry s.g. of 1.6
Consult a FLSmidth Krebs Sales Engineer for sizing needs. Visit our website: www.flsmidthkrebs.com
13
14
KREBS® Water-Only Cyclones
Title
Did you know
Performance
Water-Only Cyclones are used to “clean” or “wash”
raw coal making a density separation. This cyclone
design relies on the fact that the mineral matter is
denser than coal. In this case the truncated cone
bottom allows a hindered-settling bed to form which
rejects lighter coal particles, while an elongated vortex
finder lifts the light coal particles.
• Water-Only cyclones are designed to produce
a low ash coal product
• Water-Only cyclones can handle feed particle 3/4”
top-size
Benefits and Features
A characteristic of this design is that some coal losses
may take place through the apex because larger coal
particles are classified. This result can be eliminated by
using 2-stage circuitry where losses are re-cleaned in
coal spirals or secondary water only cyclones. An
overall more efficient separation results.
• One can adjust separating density with pressure,
apex size and vortex finder length
• Compared to other water-based coal washing
devices, the water-only cyclone offers a more
compact design and provides relatively low separation densities
Finer coals must be cleaned in smaller diameter wateronly cyclones; otherwise, drag forces in large diameter
cyclones cause the fine, high ash particles to report to
clean coal. Both pressure and feed density affect the
separating gravity.
• Many different liner materials are available
• Shorter Vortex Finders ensure low separating
densities
• Long-Body ensures low separating densities
Note: Our D15LB-S-327 is specifically designed
to clean 1MM top size coal. Combined with
a second stage spiral circuit, the system can provide
separation densities from
1.65 to 2.00 SG
• Performance simulations and technical support by
FLSmidth Krebs
KREBS Water Only Cyclones - Typical Operating Parameters (U.S. Units)
Feed Particle
Maximum
Size
Effective
Mesh of
Separation
Dry Feed
Range
(stph)
D10LB-S-218
10 Mesh
100/150 Mesh
4-8
190-260
D15LB-S245
28 Mesh.
65/100 Mesh
12-18
D15LB-S327
14 Mesh.
65/100 Mesh
D20B-S-260
1/4-in.
D20LSB-S-333
D26-S-224
Krebs Model
Designation
Pulp
Pressure
Flowrate
Drop Range
Range (gpm)
(psi)
Maximum Feed
Percent Solids
WT%
VOL %
8-15
10%
7%
400-580
10-18
12%
8%
12-25
510-720
10-20
12%
8%
48/65 Mesh
25-45
820-1050
12-20
15%
11%
1/2-in.
35/48 Mesh
35-60
1100-1500
12-20
15%
11%
3/4-in.
35/48 Mesh
50-90
1490-2200
12-22
20%
15%
Consult a FLSmidth Krebs Sales Engineer for sizing needs. Visit our website: www.flsmidthkrebs.com
14
15
KREBS® Water-Only Cyclones
Title
KREBS Water Only Cyclones - Typical Operating Parameters (Metric Units)
Feed Particle
Maximum
Size
Effective
Mesh of
Separation
Dry Feed
Range
(mtph)
Pulp
Flowrate
Range
(m3/h)
Pressure
Drop Range
(psi)
D10LB-S-218
10 Mesh
100/150 Mesh
4-7
43-59
D15LB-S245
3mm
65/100 Mesh
11-16
D15LB-S327
6mm
65/100 Mesh
D20B-S-260
13mm
D20LSB-S-333
D26-S-224
Title
Krebs Model
Designation
WT%
VOL %
55-103
10%
7%
91-132
69-124
12%
8%
11-23
116-164
69-138
12%
8%
48/65 Mesh
23-41
186-238
83-138
15%
11%
13mm
35/48 Mesh
32-54
250-341
83-138
15%
11%
19mm
35/48 Mesh
45-82
338-500
83-152
20%
15%
• Bullets
• Bullets
Maximum Feed
Percent Solids
Consult a FLSmidth Krebs Sales Engineer for sizing needs. Visit our website: www.flsmidthkrebs.com
15
KREBS® Ceramic Liners for Cyclones
Ceramic Liner Options
Most coal applications require all wetted cyclone
surfaces to be ceramic lined especially Heavy Media
Cyclones where dense magnetite and raw coal (containing sand and rocks) impinges upon the liners.
For severe applications, we may recommend that upper
portions of the cyclone be protected with nitride
bonded silicon carbide (CR) liners, while the lower
sections and apex be protected with more abrasive
resistant ceramic liners. In extremely severe applications
a reaction bonded silicon carbide (CX ) apex insert
might be recommended. With several ceramic liner
options, maintenance is markedly reduced.
High quality cast ceramics provide geometric accuracy
equal to high-chrome cast iron but provide significantly
longer service life. Using only cast liners results in less
turbulence, finer cut points and longer service life.
Krebs flexible design permits applying special ceramics
where required throughout the cyclone body.
Ceramic Liner Inspection
With several ceramic liner options available, maintenance can be markedly reduced. For Classifying,
Water-Only, and Heavy Media Cyclones, apex wear is
the most important issue and the easiest to monitor.
With all pump motor switches properly secured, a light
and measuring device are usually the only items
required for this inspection.
To inspect the other liners, usually an apex assembly or
overflow pipe/vortex finder can be removed. If this still
doesn’t allow adequate view of all liners, additional
disassembly will be required. Because the liners are
somewhat brittle, all ceramic lined cyclones should be
handled carefully; hammering on any surface of the
cyclone is not recommended.
Because Krebs ceramic lined cyclones lasts so long,
some maintenance expertise may be lost between
rebuilds. In this case, please contact FLSmidth Krebs or
your local representative for assistance; some of the
representatives may also be able to provide a rebuild or
exchange service.
16
KREBS® Ceramic Liners for Cyclones
KREBS TYPICAL CERAMIC LINERS
Krebs Model
Designation
CC
CB
Heavy Media Cyclone Inlet
CR
CX
CZ
-
-
-
Heavy Media Cyclone Lower Cone
Heavy Media Cyclone Apex
gMAX Classifying Cyclone Inlet
-
-
-
-
-
-
gMAX Classifying Cyclone Lower Cone
gMax Classifying Cyclone Apex
Water Only Cyclone Inlet
Water Only Cyclone Truncated Cone
Water Only Cyclone Apex
Standard Liner (standard varies by cyclone diameter)
Available Liner
-
Not Available
CERAMIC MATERIALS
CC = Alumina Bonded Silicon Carbide
90% Alumina Tile, this material holds up well in coal
applications and is used to line cones and some apexes.
CB = Alumina Bonded Silicon Carbide
96% Alumina Tile, this material holds up well in coal
applications and is used to line the difficult geometry associated
with the inlet head of large diameter heavy media cyclones.
CR = Nitride Bonded Silicon Carbide
This has been the standard material used by Krebs for inlet
heads and cylinders and cones for over 30 years. This material
has been modified over the years to improve the dimensional
consistency of the parts, but the basic composition has
remained unchanged.
CX = Reaction Bonded Silicon Carbide
This is typically used in highly abrasive applications. It will
outlast the standard CR material by about 3 times.
CZ= Alpha Sintered Silicon Carbide
This is typically used in most extreme abrasive applications.
It is the most wear resistant ceramic material we offer and it
will outlast the standard CR material by 9-10 times.
Consult a FLSmidth Krebs Sales Engineer for material selections. Visit our website: www.flsmidthkrebs.com
176
KREBS® De-slime Cyclones
Title Separation
Finer
Did you know
Benefits and Features
Krebs 6” gMAX cyclone is used for ultra-fine coal
desliming applications requiring 270-325 mesh
separation.
• A 2-component molded cyclone urethane design
provides maximum strength and wear
characteristics
Used prior to flotation circuits, the deslime cyclone
allows for removal of clays and inert material to the
overflow. This reduces volume to flotation and increases
flotation residence time as a result.
• Quick disconnect lower cone and apex assemblies
allow for rapid inspection and replacement
• Krebs offers custom “spider” and conventional
radial manifold designs to minimize footprint while
maximizing throughput
Performance
•
Cyclone capacities from 95 to 300 gpm per unit
18
KREBS® Coal Spirals
Did you know
• The New Krebs Coal Spiral is a technologically advanced design
• Krebs rougher/cleaner “CPX” spiral design allows coal to be rewashed in a second stage spiral helix located immediately below the
primary spiral
• Spiral concentrators use differences in density to separate fine coal
simply, efficiently, and cost effectively
• Krebs offers a comprehensive range of spiral units for coal
preparation
Benefits and Features
• Single, double, and triple start configurations
• Single pass or rougher/cleaner compound designs available
• Integral product piping system which eliminates the need for open
launders
• Wear and corrosion resistant construction
• Performance simulations and technical support by FLSmidth Krebs
• New product boot design with vortex breaker for a longer wear life
• Integral “lock-in-place” cutter positioner and indicator
• Recessed cutter position for enhanced separation, reducing product
misplacement
Performance
• The GPX and CPX Coal Spirals are designed to produce a low ash
coal product at high efficiency while rejecting a high ash refuse
stream
• Spiral feed capacity is 2-3 STPH (1.8 - 2.7 MTPH) per start dependent
on raw coal quality and refuse amount to be discarded
• Optimum spiral feed size is -1mm to 0.15mm (14Mx100M)
Note: Krebs Coal Spirals are supplied in complete modular designs including support framework, feed distribution system and
product piping system. Assemblies will be designed to meet your
application requirements. Consult a FLSmidth Krebs Sales
Engineer for any technical or quotation requests.
www.flsmidthkrebs.com
194
KREBS® Coal Spirals
Title
New Polyurethane Product Collection Boot
• Handles allow for positioning of all cutters
simultaneously
• No need to reach into Helix to adjust
• Increased capacity
• Mechanism allows positive lockout once selection
is made
• Revised internal profile assures no
misplacements into other product streams
• Internal Rotation Breaker: reduces wear on
boot assembly
New Polyurethane Performance
Enhancing Berms
Feed Berms
• Allows for low flow conditions without losing coal
Refuse Berms
• Used to ensure no coal loss on very high yield coals
Cleaner Berm
• Krebs will select appropriate style based on your
plant conditions
Transition Box
• Re-mixes Coal and Mids prior to final turns
• Allows for a better separation
• Refuse is bypassed to assure no product contamination
Title
KREBS® TechnequipTM Knife Gate Valve
for Fine Coal Applications
www.flsmidthkrebs.com
Title
Did you know
Technequip™
knife gate valve is a heavy duty premium
•
Bullets
valve, designed for harsh service.
• Bullets
The valves are available with manual handwheel, bevel
gear, pneumatic, hydraulic, and electric actuators.
Numerous accessories and options are available,
including but not limited to, solenoids, limit switches,
junction boxes and alternate gate and elastomer
materials.
Benefits
• Reliable operation
• Longer wear life
• Open Body Design ejects material from the bottom
to ensure a 100% bubble tight seal
Options and Features
• Available in sizes from 2” through 48”
• Dust Boot and Stem Cover on manual valves
• Epoxy-coated Cast Ductile Iron Body
• Replaceable Wear Sleeves
• Retainer Flanges
• Open Body / Packing-less Design
• Fluorocarbon coated stainless steel gate
• Bi-directional operation
• Internal ring magnet on all composite air cylinders
• Frames can accept any type of actuator
• Pressure ratings available up to 740PSI
Ideal for Coal:
• Pump suction valves
• Cyclone isolation or distribution
Technology Center
FLSmidth Krebs
5505 W Gillette Road
Tucson, AZ 85743-9501
USA
Tel: +1 520 744 8200
Fax: +1 520 744 8300
E-mail: [email protected]
www.flsmidthkrebs.com
Copyright © 2014 FLSmidth A/S. ALL RIGHTS RESERVED. FLSmidth is a (registered) trademark of FLSmidth A/S. This brochure makes no offers, representations or
warranties (express or implied), and information and data contained in this brochure are for general reference only and may change at any time.
COAL Rev. 11/13/2015 ljr-us
1