Model: TS-3

I
Model: TS-3
INSTALLATION AND OPERATING INSTRUCTIONS
IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS DO NOT
ATTEMPT TO INSTALL OR OPERATE
INTRODUCTION
This TS-3 wired wall thermostat was developed to provide a safe, reliable control system for gas heating appliances. The system can
be operated thermostatically or manually from the wall unit.
WALL MOUNT THERMOSTAT
The TS-3 wired thermostat operates on (2) 3V Button Cell (Included) which powers the LCD screen
and circuit board. Before using the TS-3 wall thermostat the 3V batteries must be installed into the
battery compartments.
LCD
DISPLAY
ROOM “SET” TEMP
THERMO
MODE
It is recommended that CR2032 lithium batteries always be used for longer battery life and
maximum operational performance. If the LCD screen will not come on, check the 3V Button Cell
battery.
SET
BUTTON
ON/UP
BUTTON
SET
OFF
ON
OFF/DOWN
BUTTON
TO INSTALL BATTERIES IN THE THERMOSTAT
1. Remove face from backing wall plate this is done by sliding the face up about 1/2” then pull the face off the base plate. As
shown in Figure #1
2. Locate the (2) holders for the 3V button cell batteries.
3. Slide the button cell batteries into the battery holders. (Make sure that the batteries are installed with the (+) plus side facing
you or up.
4. Reinstall the face to the backing plate this is done by sliding the face in and down about 1/2” then check that the (2) male
terminal connectors on the face are engaged in the female terminal connectors on the backing plate . As show in Figure #1
TO REMOVE THE BATTERIES FROM THE THERMOSTAT
1. Remove face from backing plate this is done by sliding the face up about 1/2” then pull the face off the base plate. As shown in
Figure #1
2. Locate the (2) holders for the 3V button cell batteries.
3. Insert a small screwdriver into the slot above the button cell battery and push the battery out. As shown in Figure #2
4. Reinstall the face to the backing plate this is done by sliding the face in and down about 1/2” then check that the (2) male
terminal connectors on the face are engaged in the female terminal connectors on the backing plate. As show in Figure #1
Figure #1
RO
OM
Figure #2
TE
M
P
Battery Removal
Slots
ON
SE
T
OF
F
+
Plus
Side
+
Plus
Side
(2) 3 Volt Button
Cell Batteries
___________________________________________________________________________________________________________
Skytech: TS-3
REV.1-19-12 Page 1 of 5
WIRED WALL MOUNT THERMOSTAT OPERATION
FUNCTIONS
1
2
3
ROOM
SET
TEMP
5
ROOM
SET
1.
2.
3.
4.
5.
ROOM TEMP – Current room temperature.
F – Degrees Fahrenheit (C Indicates degrees Celsius)
FLAME ICON – Indicates APPLIANCE IS ON.
SET- Indicates TS/R-3 is in thermostat mode.
DASHES – Indicate thermostat mode is being disabled. When
TS-3 is not in the thermostat mode. The word (SET) will not appear.
TEMP
4
1.
SET
OFF
ON
2.
This TS/R-3 Wired wall Thermostat has ON, OFF, and SET functions that are activated by
pressing the buttons on the face of the TS-3.
If the LCD will not come on, check the 3V-button cell battery.
SETTING MANUAL OPERATION
1.
2.
When the ON button on the TS-3 is pressed a flame icon on the LCD screen will appear when
the appliance is ON.
When the appliance is OFF the flame icon will not appear.
TEMP
ROOM
SETTING THERMOSTAT OPERATION
1.
2.
3.
ROOM
SET
TEMP
ROOM
SET
TEMP
4.
5.
0
If the TS-3 is in the thermostat mode the word (SET) will appear on the LCD screen.
When the SET button is pressed the temperature digits will begin to flash.
While the temperature digits are flashing use the ON button to increase the set
temperature or use the OFF button to decrease the set temperature to your desired
temperature.
When the desired temperature setting is reached press the SET button, again and the
word SET will appear on the LCD screen and now the thermostat will automatically send
an ON or OFF signal to the appliance.
To disengage the thermostat mode push the OFF button or push and hold the SET button
until (2) dashes appear on the LCD screen. When you release the SET button this will
disengage the thermostat mode and the word SET will disappear from the LCD screen.
0
SETTING F / C SCALE
0
0
The factory setting for temperature is degrees Fahrenheit ( F ) . To change this setting to Centigrade ( C ), you must press and hold
both the ON and OFF buttons on the transmitter at the same time until the LCD displays the change. If you want to convert back,
repeat the above procedure.
THERMO UPDATING FEATURE
This SKYTECH wired wall thermostat has a THERMO UPDATING Feature built into its software. The THERMO UPDATING Feature
operates in the following manner, but only in the THERMOSTAT MODE:
The TS-3 normally reads the ROOM temperature every 2 minutes checking the ROOM temperature against the SET temperature and
then sends a signal to the appliance.
NOTE: When locating the TS-3 on a wall remember it should be kept away from direct sources of heat such as heating appliance,
incandescent lighting, and direct sunlight. Leaving the TS-3 in direct sunlight, for example, will cause its heat-sensing diode to read the
room temperature higher than it actually is; if in THERMOSTAT mode, it may not turn on the appliance even if the ambient ROOM
temperature is below the SET temperature.
___________________________________________________________________________________________________________
Skytech: TS-3
REV.1-19-12 Page 2 of 5
INSTALLATION INSTRUCTIONS
WALL MOUNTING THE TS-3 THERMOSTAT
1.
2.
3.
4.
5.
6.
Remove face from backing plate as shown in Figure #1 then locate the
TS-3 to where the (2) thermostat wires from the appliance can be
pulled through the hole on the backing plate and connect them to the (2)
terminal screws.
After locating the (2) two mounting holes and mark the holes on the wall.
Use the (2) two dry wall anchors and screws (that are supplied) to mount
the base plate to the wall as shown.
Thermostat can also be mounted onto an existing (Plastic) electrical box.
Base plate should be mounted level on the wall for best operation
Reinstall the face to the backing plate this is done by sliding the face in and
down about 1/2” then check that the (2) male terminal connectors on the face
are engaged in the female terminal connectors on the backing plate. As shown
in Figure #1
L
WAL
RO
OM
ON
TE
MP
SE
T
OF
F
GENERAL INFORMATION
WARNING
This TS-3 wired wall thermostat must be installed exactly as outlined in these instructions. Read all instructions completely before
attempting installation. Follow instructions carefully during installation. Any modifications of the TS-3 or any of its components will void
the warranty and may be pose a fire hazard.
Do not connect any gas valve or electronic module directly to 110-120VAC power. Consult gas appliance manufacturer’s instructions
and wiring schematics for proper placement of all wires. All electronic modules are to be wired to manufacturer’s specifications.
WIRING INSTRUCTIONS
A qualified electrician or a gas technician who is familiar with the gas appliance and gas valves that will be operated by this remote
should install the remote control system. Incorrect wiring connections WILL cause damage to the gas valve or electronic module
operating the gas appliance and may also damage the remote receiver.
WIRING MILLIVOLT VALVES - ELECTRONIC SPARK IGNITIONS – OTHER APPLIANCES
This TS-3 wired wall thermostat connects to a millivolt gas valve, electronic spark ignition systems or other heating appliances as
shown below in Figure #3, Figure #4, & Figure #5. Connect 18 gauge stranded or solid wires from the TS-3 wired wall thermostat to
the gas valve, or electronic module.
TERMINAL BLOCK
ON MILLIVOLT
GAS VALVES
TH
TH
TP
RO
OM
ON
TE
MP
ELECTRONIC MODULE
Thermopile &
Pilot Assemb
TR
RO
OM
MP
TP
SE
T
OF
F
OF
F
(2) Screw terminals
to connect wires
from millivolt valve
TS-3 Wired
Wall Thermostat
Figure #3(Millivolt Valve)
110/24VAC
Transformer
neutral wire
ON
SE
T
TH
TE
(2) Screw terminals
to connect wires
from electronic module
24VAC
hot wire
TS-3 Wired
Wall Thermostat
120VAC Input
Figure #4 (Electronic Spark System)
___________________________________________________________________________________________________________
Skytech: TS-3
REV.1-19-12 Page 3 of 5
Other
Appliance
Power supply Could b
12VAC, 12VDC, 24VAC
(2) wires from
appliance
(Not Includ
RO
OM
ON
TE
MP
SE
T
OF
F
(2) Screw terminals
to connect wires
from appliance
TS-3 Wired
Wall Thermostat
Figure #5 (Other Appliances)
SYSTEM CHECK
MILLIVOLT VALVES - ELECTRONIC IGNITION SYSTEMS – OTHER APPLIANCES
Light your gas appliance following the lighting instructions that came with the appliance. Confirm that the pilot flame is on; it must be in
operation for the main gas valve to operate, if you have an electronic ignition system check the power source as well.
•
•
•
Press the ON button on the TS-3 to turn the system to ON manually. The main flame should come ON.
Press the OFF button on the TS-3 to turn the system to OFF manually. The main flame should extinguish (the pilot flame will
remain on if you are using a millivolt gas valve system).
Press the SET button on the TS-3 to change the system to THERMO. Hold the SET button to set the temperature on the TS-3 to a
0
0
temperature of a least 2 F (1 C) above the ROOM temperature displayed on the LCD screen. With this manual setting, the
0
0
normal thermostatic cycle is overridden and the system flame will ignite. Set the SET temperature to at least 2 F (1 C) below the
room temperature and the system flame will extinguish in a few seconds. Thereafter, it should continue to cycle to on and off
thermostatically approximately every two minutes as the ROOM temperature changes, but only when the temperature differential
0
0
0
between ROOM and SET temperatures differ at least 2 F (1 C). The 2 F differential is the factory setting.
GENERAL INFORMATION
BATTERY LIFE
Life expectancy of lithium button cell batteries in the TS-3 should be at least (1) season (8) months. Check and replace both batteries
annually.. The TS-3 should operate with as little as 2.4 volts of battery power, measuring at each of the 3-volt button cell batteries.
TROUBLE SHOOTING
Should you encounter problems with your appliance system, the problem may be with the appliance itself or it could be with the TS-3
wired wall thermostat. Review the appliance manufacturer’s operation manual to make sure all connections are properly made. Then
check the operation of the TS-3 in the following manner:
___________________________________________________________________________________________________________
Skytech: TS-3
REV.1-19-12 Page 4 of 5
1.
2.
3.
4.
Be sure the TS/R-3’s batteries are properly installed and that the battery output is 2.4 volts on each battery or more. If one
battery is installed backward the wired wall thermostat will not operate.
The TS-3 has (2) 3 volt button cell batteries (1) button cell operates the LCD screen and the other button cell powers the PCB
board. If the button cell battery that controls sending the PCB board is low or defective the LCD screen may work but the PCB relay
may not close the contact (Check each button cell battery)
Check that the (2) male terminal connectors on the face are engaged in the female terminal connectors on the backing plate.
Check the wire connections to the TS-3 from the appliance that they are properly connected
SPECIFICATIONS
BATTERIES: TS-3 wired wall thermostat – 2ea. (CR2032) 3.0 volt lithium button cell batteries.
FOR TECHNICAL
SERVICE, CALL:
U.S. INQUIRIES
888/672-8929 or
260/459-1703
Website: skytechsystem.com
CANADIAN INQUIRIES
877-472-3923
MANUFACTURED EXCLUSIVELY FOR SKYTECH II, INC
___________________________________________________________________________________________________________
Skytech: TS-3
REV.1-19-12 Page 5 of 5
Limited Lifetime Warranty
SKYTECH II warrants the SKYTECH REMOTE CONTROL SYSTEM for a Limited Lifetime of the original
owner of this system. This warranty is not transferable to another person it is for the original purchaser of the
product. Should any part fail because of defective workmanship or material from the original date of purchase.
SKYTECH II will repair or, at SKYTECH II option, replace the defective parts.
Replacement parts will be available at no charge for the first (5) five years of this warranty, and will be
available at market cost for the Lifetime of the product to that original owner. If SKYTECH II does not have the
parts for an individual model, then a replacement SYSTEM will be provided. At no charge for the first (5) five
years and sold at market cost for the Lifetime of that product to the original owner.
The Owner must provide a bill of sale, cancelled check, or payment record should be kept to verify purchase
date and establish warranty period. Travel, diagnostic cost, service labor to repair the defective SYSTEM, and
freight charges on warranty parts to and from the factory will be the responsibility of the owner. SKYTECH will
not be responsible for labor charges and/or damage incurred in installation, repair, replacement, or for
incidental or consequential damages. Batteries and any damage caused by them are not covered by them are
not covered by this warranty.
This warranty does not cover claims, which do not involve defective workmanship or materials.
Damage to the SYSTEM caused by accident, misuse, abuse, or installation error, whether performed by a
contractor, Service Company, or owner, is not covered by this warranty. Modification of the SKYTECH product
will void this warranty.
IN NO EVENT SHALL SKYTECH BE LIABLE FOR INCIDENTAL AND CONSEQUENTIAL INCLUDING THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS, ARE LIMITED TO THE DURATION OF THIS WRITTEN
WARRANTY. THIS WARRANTY SUPERSEDES ALL OTHER ORAL OR WRITTEN WARRANTIES.
Some States do not allow the exclusion or limitation of incidental and consequential damages or limitation on
how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you
specific rights and you may have other rights, which vary from state, province, and nation.
How to Obtain Service:
Contact SKYTECH II or your SKYTECH Dealer direct with the following information:
Name, Address, Telephone Number of Owner
Date of Purchase, Proof of Purchase
Model Name, Date Code
Any relevant information or circumstances, e.g., installation, mode of operation when defect was noted.
Warranty claim process will start with all of this information. SKYTECH will reserve the right to physically
inspect the product for defects, by authorized representatives.
Detach at this line for return to: Skytech II 9230 Conservation Way, Fort Wayne, IN 46809 Telephone: (888) 672-8929
Purchase Date:
Model:
Purchased From:
Customer
Name
Date Code:
Date:
Number of Santa’s Helpers
Address
City
Credit Card Number
(Visa and MasterCard Only)
State/Prov.
Zip/Postal Code
Expiring Date
See other side for a special offer for all Remote control Customers
Santa’s Helper
Exclusive offer to Skytech Remote Control Owners
This special offer is only provided to customers of Skytech II, Inc. that have purchased a remote control for
their Hearth Product. This remote control system can be used for any 110Volt appliance, but perfect your
Christmas Tree Lights or any other appliance that is difficult to reach or plug in. Simply plug the receiver into
your wall outlet and your appliance into the receiver, push the ON button on the transmitter and you are in
business. It’s that easy.
The list price of $29.95 for the Santa’s Helper has been cut almost in half to $15.00 USD for this exclusive
offer. Shipping and handling of $5.00 $USD should be added. Send your check, money order or your Visa /
MasterCard number, with Expiration Date to our office, along with the warranty information from your remote
control for your Hearth Product. You can send this via mail, fax, or e-mail.
Skytech II, Inc.
9230 Conservation Way
Fort Wayne, IN
46809
1 (888) 672-8929
1 (888) 672-8024 Fax
[email protected] e-mail