Amplifiers and Modulators

Transcription

Amplifiers
and
Modulators
Premium range of VHF/UHF and
combination mast head and house
distribution amplifiers and modulators
to suit all needs. Matchmaster’s range
of mast head amplifiers have either
694MHz or 652MHz built in low pass
LTE/4G filters to reduce interference
from 4G mobile transmissions.
Products may vary from photo shown | www.matchmaster.com.au 41
4 Way Amplifier Splitter
Block D & E UHF Amplifier
With LTE Filter And
Power Supply
10MM-AS38
Features and Benefits
»» Built in adjustable gain regulators
»» Diecast housing inside heavy duty casting
»» Built in power supply
»» Suitable for
10MM-DE34P
»» Built in 4G LTE 694MHz
low pass filter
apartments
»» Filtering at 750MHz is >50dB
at maximum gain for UHF of 34dB
»» Gain adjustment switch that is selectable
between 15, 25 and 34dB
»» The UHF input return loss is >11dB
10MM-AS38 Specifications
Frequency Range
Gain
Gain Adjustment
Max Output Level IMD3=60dB
(DIN45004B)
Input And Output
Return Loss
Noise Figure
Test Point Attenuation
Port To Port Output Isolation
Power Consumption
Operating Temp. Range
with a noise figure of <2.9dB for UHF
47-862MHZ
20dB
0 ÷ -16dB
100dBµV
>10dB
<5dB
-20dB
>16dB
230V ~ 50 Hz 3W
-20°C ÷ +50°C
»» Can be used with UHF antenna’s only
»» The pack contains a 14VDC power supply and
cable ties for mounting
Distribution Amplifier 40dB U/V
with Power Supply 4G Filtered
10MM-DMA42
»» Frequency range 45-694MHz
»» Switchable inputs for UHF & VHF or U/V
»» Separate gain controls for
band 1 & FM,
band 3 & UHF
2 Way Amplifier Splitter
»» Metal casing for
10MM-AS39
excellent heat
dissipation
»» Built in adjustable gain regulators
»» Diecast housing inside
heavy duty casting
»» Built in power supply
»» Suitable for apartments
10MM-AS39 Specifications
Frequency Range
Gain
Gain Adjustment
Max Output Level IMD3=60dB
(DIN45004B)
Input And Output
Return Loss
Noise Figure
Port To Port Output Isolation
Power Consumption
47-862MHZ
20dB
0 ÷ -12dB
100dBµV
>10dB
<6dB
>16dB
230V ~ 50 Hz 3W
-20°C ÷ +50°C
42 www.matchmaster.com.au | Products may vary from photo shown
10MM-DMA42 Specifications
No. of Inputs
No. of Outputs
Gain
UHF
VHF
Input & Output
Return Loss
Noise Figure
Gain Adjust
VHF
Maximum Output
60dBIMR
35IMR
Screening
VHF
UHF
Input/Output Impedance
Power Source
Power Consumption
2 ‘F’ Type
1 ‘F’ Type
40dB
33dB
>10dB
<8dB
15dB
115dBµV (2 Ch)
103dBµV
(Cenelec 42Ch)
>75dB
>65dB
75�
14-18VDC
200mA
TERRA Amplifier 30dB Gain
Amplifier Satellite/Terrestrial
10MM-HA024R30
10MM-HSA100
»» Compact and reliable, great for
»» Amplifies both satellite and terrestrial services
»» Terrestrial stage can be switched
adding extra points to an indoor area
»» Variable slope and gain control built-in
»» Locally powered using 240V mains power
»» ‘F’ connectors on all ports
»» External test port, passive return path built in
»» Switchable internal amplifier section allowing it to
switch effortlessly between low and medium gain
performance. This allows the gain of the amplifier
to be reduced without degrading the quality of the
signal being amplified
10MM-HA024R30 Specifications
18-20/27-30dB (Fixed
Gain
Slope Pre Correction)
Gain Adjustment
17dB
Slope Adjustment
Flatness
±0.75dB
>14dB at 40MHz; -1.5
Input & Output
dB/Oct, But Not Less
Return Loss
10dB
Output Level CTB,
97dBµV
CSO (EN50083-3)
Test Point
-30dB
Noise Figure
8.5dB
-20°C ÷ +50°C
to passive if it is not needed
»» DC power pass through, allows power
to be passed to an LNB or masthead amplifier
»» Independent gain and slope adjustment available
for both satellite and terrestrial bands.
»» Foxtel approved (F30672)
»» Ventilated power-supply section allowing for
greater heat dissipation and a longer MTBF
when compared to other amplifiers
10MM-HSA100 Specifications
Frequency Range SAT IF
Frequency Range
TERR TV
Gain SAT IF
Gain TERR TV
Gain Adjustment SAT IF
Gain Adjustment
TERR TV*
Slope Adjustment SAT IF
Slope Adjustment
TERR TV*
Input & Output Return Loss SAT
IF
Input & Output Return Loss
TERR TV
Maximum Output Level
IMD3=60dB (DIN45004B) TERR
TV
Noise Figure SAT IF
Noise Figure TERR TV
Mains Power Consumption
Temperature Range
950-2400MHz
47-862MHz
23-31dB
(Pre Correction)
21-24dB
(Pre
Correction)/4dB Switchable
10dB
18dB
14/8dB
Switchable
18dB
� 10dB
� 10dB
115dBµV
8dB
8dB
230V ~ 50Hz
7.5W
-20°C ÷ +50°C
*Terrestrial gain, slope, adjustment and return path
are not available at passive terrestrial TV mode
Amplifier UHF 15dB 4G Filter
10MM-J15C-4G
»» U/V stabilised housing and cable tie
»» Non-corrosive circuit board
»» ‘F’ connectors
»» Also available with power
supply (10MM-J15C-4GP)
10MM-J15C-4G/4GP Specifications
Frequency Range
520-694MHz
Gain Maximum
18dB
Noise Figure
2dB
Maximum Input Level
84dBµV
95dBµV
Consumption
20mA/14VDC
Amplifier UHF 4G Filter
Super Low Noise
10MM-J25SLN-4G
»» U/V stabilised housing
supply (10MM-J25SLN-4GP)
10MM-J25SLN-4G/4GP Specifications
Frequency Range
520-694MHz
Gain
10-25dB
Noise Figure
1.5dB
Maximum Input Level
85dBµV
105dBµV
Consumption
55mA/14VDC
Amplifier 34dB UHF/VHF
4G Filter
Amplifier Masthead
UHF/VHF 24dB 4G Filter
10MM-J24BF-4G
»» Can be set to VHF only or combination
»» U/V stabilised housing
supply (10MM-J24BF-4GP)
10MM-J24BF-4G/4GP Specifications
Band
VHF
UHF
Gain Maximum
24dB
Gain Control
14dB
Input Voltage
14VDC
Noise Figure
3.5dB
Input Maximum
35dBµV
Output Maximum
105dBµV
Frequency Range
174-230MHz 520-694MHz
Amplifier UHF/VHF
34dB 4G Filter
10MM-J34BF-4G
supply (10MM-J34BF-4GP)
10MM-J34BF-4G/4GP Specifications
Band
VHF
UHF
Gain Maximum
28dB
34dB
Gain Control
-15dB
Input Voltage
14VDC
Noise Figure
3.5dB
2.5dB
Input Maximum
35dBµV
Output Maximum
105dBµV
Frequency Range
174-230MHz 520-694MHz
10MM-J34C-4G
»» Available with power
supply (10MM-J34C-4GP)
10MM-J34C-4G/4GP Specifications
Band
VHF
UHF
Frequency Range
174-230MHz 520-694MHz
Gain Maximum
Passive-2 dB
36dB
Noise Figure
2.5dB
Maximum Input
84dBµV
Maximum Output
102dBµV
Consumption
60mA/14VDC
Amplifier 20dB Gain
Plug In 4G LTE Filter
10MM-MA20FL
»» 4G Lowpass filter output 694MHz
»» Frequency 40-694MHz
»» Ideal for improving
reception on a single TV.
»» Warning indoor use only.
Do not allow exposure to moisture
or harmful elements.
Amplifier 2 Way
4G LTE Filter
Amplifier 4 Way
4G LTE Filter
10MM-MA22FL
10MM-MA24RL
»» Ideal for TV and FM signals
»» Power supply can be used
to be split to 2 TV's
»» 2 Way UHF/VHF amplifier
with integrated power
1 input 2 outputs
»» Frequency range
40-694MHz
»» 4G LTE low pass filter
694MHz
»» 3 x A3 female IEC adaptors
»» 15dB ± 3dB Gain
simultaneously for a masthead amplifier
»» Warning: Indoor use only.
10MM-MA24RL Specifications
Frequency Range
45-694MHz
Number of Inputs
1
Typical Gain
8dB
Maximum Output
92dBµV at 60dB IMR
Low Noise
�7.2dB
Power Supply
12V/500mA
Power Pass
230VAC/50Hz
Amplifier Masthead
4G UHF/VHF 30dB
With Power Supply
Amplifier 4G VHF/UHF
10MM-MA30PDF
»» Includes 14VDC power
10MM-MD15P
supply and cable
ties for mounting
»» Posistor protected right
»» Passive VHF passing or
combining with 1.5dB
max insertion loss
angle regulated
power supply
»» Heavy duty
clamping system
»» Use with a combination antenna
»» LTE Filter: OFF: VHF + Ch21-69 (47MHz - 820MHz)
»» New slide switchable
input selection
ON: VHF + Ch21-46 (47MHz - 652MHz)
»» Filter attenuation @ 720MHz: 19dB,
»» Adjustable interstage gain on UHF & VHF
»» 4G 652MHz low pass filter built in
@ 750MHz: 30dB
Block A, B & C UHF/VHF Amplifier
with LTE Filter and Power Supply
10MM-MB34P
»» Built in 4G LTE 610MHz low pass filter
»» Filtering at 700MHz is >50dB at maximum gain for UHF of 34dB
»» Gain adjustment switch that is selectable between
15, 25 and 34dB
»» The VHF input return loss is >13dB and the UHF
return loss is >11dB with a noise figure of <2.9dB for UHF
»» Can be used with VHF or UHF antenna’s or a combination
of both and includes a VHF on off switch
»» The pack contains a 14VDC power supply
and cable ties for mounting
Masthead Amplifier UHF
24dB - 4G Filter And
Power Supply
10MM-MD24UP
»» 694MHz built in 4G
low pass filter
»» Switchable 694MHz
low pass filter
»» Gain with LTE filter 694MHz 24dB
»» VHF switch diplexing max attenuation
2.84dB at 230MHz
10MM-MD24UP Specifications
UHF
Gain
BIII
Return Loss
Noise
Impedance
Operating Voltage
Operating Current
Output Level for dB Gain
Amplifier (Definition per
ENBS50083-9 Standard)
DC Powered
Housing
25dB
-2±1.5dB
�-10dB
5.5dB
75�
24VDC
65±10mA
�98dBµV
14VDC
Nickle Plated
75�, Female ‘F’
Type
-20°C - +60°C
Connector
Working Temperature
»» Heavy duty clamping system
Modulator TERRA DSB
Stereo 85dBµV
UHF/VHF Pre-Amplifier
with LTE Filter
10MM-MT57
10MM-MD34
»» Built-in test pattern generator (TPG)
for video and audio
»» Built in 4G LTE 694MHz
»» Frequency agile double sideband
low pass filter
multi standard TV modulators
»» Filtering at 750MHz is >50dB at
»» Adjustable audio input level and RF output level
»» Connectors: video/audio - RCA sockets -
maximum gain for UHF of 34dB
»» Can be used with a combination
antenna or separate VHF and UHF
antennas by setting the built in switch
»» Power through switch to drive extra amplifiers
for both VHF and UHF
»» The pack contains cable ties for mounting
RF - ‘F’ female
»» Foxtel Approval Number: F30811
10MM-MT57 Specifications
RF Output Level (Typical)
Level Adjustment
85dBµV
0 ÷ -20dB
170-300MHz,
470-862MHz
Frequency Range*SC
4 Output Drop Amplifier
10MM-MDR6-4P
»» Forward path 85-1000MHz
»» Return path 4-65MHz
»» 12VDC 50Hz 150mA
»» R.F Shielded
10MM-MDR6-4P Specifications
Number of Input
Gain
Insertion Loss
Noise Figure
Return Loss (IN & OUT)
Isolation (OUT & OUT)
MAX Output Level at -60dB IMD
DC Powering (INPUT-OUTPUT)
Combining Through Loss
TERR/SAT
Frequency Range of RF
Combining
Signal/Noise Ratio
Power Consumption
Operating Temperature
1.5dB/2.5dB
5-2150MHz
�55dB
230V - 50Hz 2.5W
-10°C - +50°C
Dual Power Inserter
10MM-PDL1418
1
7±2dB
-7±2dB
�4dB
�10dB
�20dB
�106dBµV
Yes
»» ‘F’ Type 500MA
»» 14VDC OUT for vertical
»» 18VDC OUT for horizontal
»» ‘F’ type power inserter to power
satellite LNBs for horizontal
and vertical polarities
Power Inserter 24VDC
10-2050MHz
Power Supply 18VDC
‘F’ Type 500MA
10MM-PI24
10MM-PSM18F
»» Insertion loss 2dB
»» Max 1.5 Amp
»» Allows for mounting of the
»» Zinc die cast housing, nickel plated
»» Insertion loss < 1dB
»» Input: 100 - 240V ~ 50/60Hz
»» Output: 18VDC 500MA
drop amp away from the
power outlet
»» Directs power to the drop amp while allowing
RF to pass to the TV
Power Supply 14V DC ‘F’ Type
10MM-PSD14
10MM-PSD14P
»» Reduces protrusion
»» Environmentally smart
»» MEPS and RoHS compliant
»» Male ‘F’ type connection
»» Output: 14VDC 300MA
»» Environmentally smart
»» MEPS and RoHS compliant
»» PAL Design Output:
14VDC 300MA
Amplifier Satellite 18dB
Inline 950-2400MHz
10MM-SA18
Universal Masthead Amplifier
With Power Supply 4G
10MM-UA30PDF
»» Maximum output of
»» Passive VHF passing or combining
105dBµV at 35dB IMR.
»» Passes both DC and 22KHz
»» The satellite amplifier is a fully screened remote
powered device which will work
in a voltage range of 12-18V DC
10MM-SA18 Specifications
No. of Inputs
No. of Outputs
Gain
Input
Return Loss
Output
Noise Figure
Maximum Output
VHF
Screening
UHF
Input/Output Impedance
Power Source
Power Consumption
Working Temperature
Power Supply 14V DC
0.3A PAL Type
1 ‘F’ Type
1 ‘F’ Type
20dB
8dB
8dB
5dB
105dBµV
>75dB
>65dB
75�
+11 ~ +20VDC
40 ~ 60mA @ 18VDC
-20°C ~ +55°C
with 1.5dB max insertion loss
»» Filter Att @ 720MHz: 19dB, @ 750MHz: 30dB
»» Use with a combination antenna or separate VHF
and UHF antennas by setting the in-built switch
»» 4G - 694MHz Low Pass LTE Filter
10MM-UA30PDF Specifications
Input Voltage
VHF Input Return Loss
UHF Input Return Loss
Power Supply Included
UHF
Band 3
Max Gain
30
30
14VDC
<13dB
Yes
FM
Band 1
30
Passive
Amplifier 39dB Forward Gain
5-30MHz Passive Return
Passive Return Path Module
For 14MM-BA213U
14MM-BA213U
14MM-PD02-65
»» High output amplifier capable of high channel loads
»» Ga-As push pull amplification for low distortion
»» Variable gain control to set output of the amplifier
»» Used in MATV system where signal
is returned back to BA213 amplifier
»» Easy plug in
and slope adjustment for cable compensation
»» Includes Passive Return Path module
»» Diecast housing for high RF screening
»» 230~260VAC mains powered
14MM-PD02-65 Specifications
Return Path
Frequency Range
Forward Path
Return Path
Attenuation
Forward Path
5-65MHz
87-862MHz
1.5dB
1dB
Active Return Path Module
For 14MM-BA213U
14MM-BA213U Specifications
Forward Path*
47-862MHz
Return Path*
5-30MHz
Forward Path Gain**
39dB
Return Path Gain
-2.5dB
Flatness***
±0.5dB
Gain Adjustment
20dB
Slope Adjustment
18dB
Typical
Inverse Cable Equaliser
0-9dB in 1dB Step
Output Level CTB, CSO
-20dB
(EN50083-3)****
Input and Output Return
>14dB
Loss*****
Noise Figure
<7dB
Test Points Attenuation
-20dB
Mains Powering
230V ~ 50Hz 11W
-20°C - +50°C
Range
* Depends on plug-in modules: return path passive
pd 02-xx or active pr 02-xx (return path modules
should be ordered separately)
** With link 0dB instead of interstage attenuators
are supplied in scope of the amplifier delivery
*** For amplifier with return path - ±0.7dB
**** Measured with 6dB interstage equaliser
***** When f�40MHz, return loss �14dB (40MHz) 1.5dB/octave, but not less 10dB
14MM-PR02-30
»» Used for TERRA BA series broadband amplifiers
»» Shapes the characteristics of the amplifier
in return path
14MM-PR02-30 Specifications
Return Path
Frequency Range
Forward Path
Return Path
Gain
Forward Path
Output Level IMD3=60dB
Gain/Slope Adjustment
Noise Figure
5-30MHz
47-862MHz
21dB
-1dB
113dBµV
20dB
4dB
CVBS To COFDM Modulator
HDMI To COFDM Modulator
14MM-DM04
14MM-DM05
»» 1 x RCA input
»» Standard Definition digital modulation
»» Allows audio/video signal input to TV distributions
»» Can be used with home entertainment systems,
»» 1 x HDMI input, MPEG4 output only
»» High Definition digital modulation
»» Allows audio/video signal input to TV distributions
»» Can be used with home entertainment systems,
surveillance control, hotel digital signage, shops etc
Specifications
Product Code
Video Encoding
Video Interface
Video Resolution
Video Aspect Rate
Video Bit Rate
Audio Encoding
Audio Interface
Audio Resolution
Audio Bit Rate
14MM-DM04
MPEG-2 MP@ML(4:2:0)
CVBS*1
720x576_50i (PAL);
720x480_60i
1.000-19.500 Mbps
MPEG1 Layer II
1*Stereo/Mono
64, 96, 128, 192, 256,
320, 384kbps
surveillance control, hotel digital signage, shops etc
14MM-DM05
H.264 MP@L 3.0 3.0/3.1/4.0
HDMI*1
Input: [email protected]/60FPS Output: 480p@30FPS
Input: 576i@50FPS Output: 576p@25FPS
Input: 720p@50/59.94/60FPS
Output: 720p@50/59.94/60FPS
Input: 1080i@50FPS Output: 1080p@25FPS
16:9, 5:4
1.000-18.000 Mbps
MPEG-1 Layer 2, MPEG-2 AAC
48KHz
64, 96, 128, 192, 256, 320 kbps
Modulator Section Standard
DVB-T COFDM
Bandwidth
6M, 7M, 8M
Constellation
QPSK, 16QAM, 64QAM
Code Rate
1/2, 2/3, 3/4, 5/6, 7/8
Guard Interval
1/32, 1/16, 1/8, 1/4
Transmission Mode
2K
2K, 8K
MER
�42dB
�31dB
RF Frequency
30-960MHz, 1KHz step
142.5-858 MHz, 1KHz step
-16 - -36dBm (73RF Output Level
-14 - +6dBm (93-113dBµV), 0.1dB step
93dBµV), 0.1dB step
System Management
Local Control; LCD + Control Buttons
Language
English
LCN Insertion
Yes
Upgrade
JTAG or USB
USB
Power Supply
DC 12V
0˚-45˚C
Amplifier With 30MHz
Return Path
14MM-HA205R30
Amplifier With 65MHz
Return Path
14MM-HA205R65
Amplifier With 30MHz Return
Path, Remote Powered
14MM-HD205R30
»» Slope adjustment for cable compensation
»» Ga-As push pull amplification for low distortion
Specifications
Product Code
Forward Path
Frequency Range
Gain Switchable*
Gain Adjustment
Slope Adjustment
Interstage Equaliser
Flatness*
Input & Output Return Loss
Output Level CTB, CSO (EN50083-3)**
Noise Figure
Test Points Attenuation
Return Path
Frequency Range
Gain Switchable
Gain Adjustment
Input Attenuator
Output Equaliser
Flatness
Return Loss
Noise Figure
Maximum Output Level IMD3=60dB
(DIN45004B)
General
Power Supply
14MM-HA205R30
14MM-HD205R30
14MM-HA205R65
47-862MHz
87-862MHz
27/36dB
18dB
18dB
-6/-3/0dB
±0.75dB
>14dB at 40MHz; -1.5dB/oct, but Not Less 10dB
109dBµV
8dB
-20dB
5-30MHz
5-65MHz
27/-4dB
18dB
-10/0dB
-6/-3/0dB
±0.75dB
>14dB
7dB (Active, 0dB Input Attenuator)
115dBµV
230V 50Hz 7.5W
24-65V 50Hz 6.5W
-20°C - +50°C
230V 50Hz 7.5W
* For amplifier with return path measured 10MHz after the starting frequency of forward path
** With 6dB interstage equaliser
Terrestrial Amplifier Broadband/
Split Band Amplifier
Amplifier 40dB Satellite
34dB Terrestrial
14MM-JA01
14MM-STA40A
»» Interstage attenuators and dynamic range of 30 dB
»» High gain (up to 40 dB), high output (122 dBµV)
»» Slope adjustment on VHF/UHF and UHF inputs
»» 4 inputs and 5/12 VDC switchable
»» Metal casing for excellent heat dissipation
»» Ideal for headend applications
»» Wall mountable
»» Separate gain and slope controls
UHF remote power
»» Broadband / Split Band Amplifier
»» VHF/UHF input with return path
14MM-JA01 Specifications
FM
Frequency
B3, DAB
Range
UHF
VHF-UHF
FM
B3, DAB
Gain
UHF
VHF-UHF
Return Pass Loss
Slope
VHF-UHF
Adjustment
Maximum Input Power
Maximum Output Power
FM
B3, DAB
Noise Figure
UHF
VHF-UHF
Return Loss
UHF Remote
Power
B3, DAB
UHF
Supply Voltage
Power Consumption
88-108MHz
174-240MHz
470-790MHz
5-1000MHz (RP: 5-65)
0-32dB
0-32dB
5-40dB
5-40dB
2dB
-18dB to -8dB
110dBµV
>122dBµV
8dB
7dB
5dB
6.5dB
>10dB
5 VDC (200mA)/12
VDC (100mA)
5 VDC (200mA)/12
VDC (100mA)
200-264VAC
5.5W
14MM-STA40A Specifications
Terrestrial
Satellite
Maximum Gain
34dB
40dB
Gain Adjust
15dB
Equalisation Adjust
17dB
7-10dB
Output Level
103dBµV
110dBµV
(42Ch/20T)
Noise Figure
<7dB
<8dB
Number of Inputs
1
5-30MHz, 45-862MHz,
Frequency Range
950-2150MHz
Return Path
5-30MHz (Passive)
Mains Voltage
240V
Connection
‘F’ Type
Return Loss
>12dB
Distribution Amplifier
45dB UHF/VHF Terrestrial
With Internal Power Supply
14MM-TA242
»» Foxtel Approved (F30092)
»» Metal casing for excellent heat dissipation
»» Separate gain
controls
Split-Band Multi-Input MATV
Amplifier
14MM-TA540A
»» 5 input terrestrial amplifier
»» TV gain adjustment range 0-20dB
»» Impedance 75Ohm
Distribution Amplifier 40dB
14MM-TWA40
14MM-TA242 Specifications
Number of Inputs
2
47-144MHz, 175-230MHz,
Frequency Range
470-862MHz
Number of Outputs
1
Amplification
BI + FM, B I I I, UHF
Gain
35/35/45dB
Gain Adjust
20dB
Output Level (42Ch)
108dBµV
Noise Figure
<8dB
Mains Voltage
240V
Test Points
Out -30dB
14MM-TA540A Specifications
Number of Inputs
5
47-108MHz, 175-230MHz,
Frequency Range
3 x 470-862MHz
Number of Outputs
1
Amplification
Terrestrial
Gain
40/40/45dB
Gain Adjust
20dB
Output Level (42Ch)
105dBµV
Noise Figure
<8dB
Mains Voltage
240V
Test Points
Out -30dB
14MM-TWA40 Specifications
Band
»» 1 input F type
»» TV gain adjustment range 0-20dB
Frequency
Band Gain
DSR
(Output
Level)
Flatness
Response
Noise
Figure
Output
Voltage
U+V/UHF
Switchable
B111
B1+FM
U+V
UHF
1744545470230MHz 144MHz 862MHz 862MHz
35dB
45dB
VHF
110dBµV
108dBµV
±1.5dB
<7dB
<8dB
DC 14V/70mA
Dual Split Band Amplifier
SAT IF/FTA
Value Line Distribution Amplifier
Remote Feed
14MM-VS95
14MM-VX25
»» Inputs: 2x TERR + SAT with output range
»» Distribution amplifier programmable
47~862MHz and 950 to 2150MHz
»» Dual Band amplifier for both
Satellite and Terrestrial
»» Mains power operated
»» Industry standard F connectors
»» Test ports integrated for measurement
»» Full diecast chassis water resistant
14MM-VS95 Specifications
Frequency
47-862MHz
950-2150MHz
Amplification
23-29dB
25-32dB
Equaliser
0/5dB
0/6dB
Attenuator
0-20dB
Isolation SAT/SAT
>45dB
Noise
�6
Max. Ouput Level
106dBµV
117dBµV
(DIN45004A1)
Max. Output Level
118dBµV
120dBµV
(DIN45004B)
Main Voltage
230VAC
Power
9W
Consumption
Housing
Zinc die-cast
Operating
Temperature
-10˚- +50˚C
Range
Screening Factor
Class A
Max. Humidity
95%
via hand controller
»» Output range 47~862MHz
»» Return path configurable from
cutoff at 30 or 65MHz
»» Remote powered 27 to 65VAC
»» Full diecast chassis water resistant
14MM-VX25 Specifications
Frequency Range
Gain
Output Level CENELEC, Flat
- CSO/CTB
Output Level CENELEC 7dB
Slope
- CSO/CTB
Attenuator
Equaliser
Interstage Attenuator
- Equaliser
Noise Figure
Test Socket
Operating Voltage
Power Consumption
Connectors Input Output
Remote Power Current
Ambient Temperature
EMC
47/85-862MHz
36dB
109dBµV
�64/�60dB
112dBµV
�63/�60dB
0-15dB, 0,5-dB-steps
0-15dB, 0,5-dB-steps
0/5dB
0/7dB
<7dB
-20dB
27-65 VAC
<13W
PG11
Input < 6 A;
Output < 3 A
-20°C - +55°C
CE, Class A
Distribution Amplifier 40dB
In House Distribution Amplifier
14MM-VX26H-3041
14MM-VX87
»» Output range 47-1006MHz
»» 40dB Gain
»» Return Path 5-30MHz 24dB
»» Integrated return channel and diplexers
»» Frequency Range US/DS 5-30/47-862 MHz
»» With passive return path
»» Adjustable level and equalizer
»» F connectors
»» Wall mounting
»» Metal housing
14MM-VX26H-3041 Specifications
Downstream
Frequency Range
Gain Single Output
CENELEC
42ch, flat
Output
6dB Slope
Level
CSO
CTB
Noise Figure
1dB Steps
Attenuator
(Jumper)
Equaliser 1.5dB Steps
Interstage Slope (Jumper)
Interstage Attenuation
(Jumper)
Test Socket
Return Path
Frequency Range
Gain (active/passive)
Noise Figure
2nd Order
Output
3rd Order
Max. Load 1 TS
Level
140
Attenuator 1dB Steps
Output Attenuator
(Jumper)
Equaliser (Jumper)
General
Operating Voltage
Power Consumption
Connectors
14MM-VX87 Specifications
Gain DS
Attenuator
Equaliser
Output Level DS
CENELEC, Flat
Output Level DS
CENELEC, 6dB Slope
Output Level DS
EN50083-5/3.Ord
Noise Figure
Return Path
RF Inputs and Outputs
Operating Voltage
Power Consumption
EMC
Remote Power Current
85-862MHz
40dB
111dBµV
114dBµV
�60dB
�60dB
�6dB
0-15dB
0/10dB
0-22.5dB
0/6dB
0/5dB
-20dB
5-65MHz
32dB/-3dB
�6dB
typ. 109dBµV
typ. 115dBµV
120dBµV
0-15dB
0/5dB
0/3/6/9dB
180-265VAC
<21W
F-Type
Input <6A;
Output <3A
-20˚ - +55˚C
28-31dB
0-18dB
3-18dB
96dBµV
98.5dBµV
114dBµV
<8dB
-2dB
‘F’ Type
230VAC 50/60Hz
3.5W
-20°C - +55°C
CE, Class A
5/8” To PG11 Adaptor
14MM-ZG01
»» Used for 14MM-VX series amplifiers
»» Adaptor for distribution cable
»» Chassis coupler
PG11 To F Type Adaptor
14MM-ZG28
»» Used for 14MM-VX24 to VX52 amplifiers
»» Adaptor for distribution cable
»» PG11 to F female

Amplifiers and Modulators

Transcription

Similar documents

AR Modular RF Tactical Booster Amplifiers

MODEL PM-900 Magnetic-Field Power Amplifier Owner`s Manual

Session SG75 Manual

Seeburg M100C - Jukeboxhistory.info

取扱説明書｜BUILT-IN-BOOSTER ANTENNA for VHF

ICE-1500D ICE-800D ICE-3500D

Down East Microwave

Fender PD250 Speaker System Set-Instructions

Professional Two-Way Radio SD-125E Series Data/Telemetry

GL-300 Amplifier Specifications