our portfolio

Transcription

our portfolio

METAN Green Health & Environmental Engineering & Consultancy Services
HEALTHCARE WASTE
MANAGEMENT AND DISPOSAL OF
BIO-MEDICAL WASTE
Healthcare waste is Segregated as follows
Healthcare Waste
(100 %)
Non-Risk Waste
Risk Waste
( 80 %)
( 20 %)
Refuse
( 40 %)
Recycling
( 40 %)
Bio-Medical
Waste
Chemical Waste
Other Waste
( 5 %)
( 0,5 %)
• Photo-Chemicals
• Pharmaceuticals
•Other Chemical w.
• Radioactive w.
• Cytotoxic w.
( 14,5 %)
• Infectious w.
• Hospital w.
• Pathological w.
METAN
WASTE OPERATORS NEED TO KNOW HOW TO TREAT
DIFFERENT WASTE STREAMS ARISEN FROM MEDICAL
SERVICES BY THE HEALTH CENTERS
WE REVIEW YOUR NEEDS AND OFFER YOU THE MOST APPROPRIATE
SOLUTION SUITS TO YOUR NEEDS
Pre-shredding kind ( We have various solutions from 25 kg/h to 500 kg/h ,
Smaller capacities are under development )
Post-shredding kind ( We have various solutions from 75 kg/h to 1000 kg/h ,
Higher capacities on demand )
[email protected]
www.metan.com.tr
+90.532.454 9077
Dr. Cemal Kaldirimci
METAN
Green Health & Environmental Engineering & Consultancy Services
LIQUID MEDICAL WASTE DESENFECTING AND NEUTROLIZING
EQUIPMENT
Liquid discharge form laboratory equipment may be
contaminated and infectious at relatively low to medium
levels.
SPECIALLY DESIGNED EQUIPMENT WOULD DISINFECT AND
PURIFY THESE KIND IF LIQUID WASTES.
BASIC FEATURES, CE
Minimizes human-induced errors.
Has high safety standards.
Has the same disinf ection efficiency at every discharge (Disinfection capacity can be increased up to 99.99%).
Makes automatic pH adjustment
Decharges the wastes into the sewerage system after processing them as specified in the regulations.
Does not require a comprehensive infrastructure and/or modification to install and operate.
Can be operated in a lab provided that adequate ventilation system exists.
Could be an economical solution due to low investment and operational costs.
MODEL 25
Waste Processing Capacity, (L/h) max.
75
MODEL 50
MODEL 100
150
300
Disinfection Chemical
Chlorine based disinfectants and ozone
Disinfection Constrate
0.1 ppm - 5.0 ppm / 5.0 ppm - 5.000 ppm (10g/lt in special applications)
pH Regulator
Sodium Hydrogene Sulphade, Hydrochloride Acid, Sodium Carbonate, Sodium Hydroxide
Power (k W)
0.10
Voltage(v/Hz)
Size- heigh x depth x width(mm)
0.12
0.20
230/50
820x800x440
820x1250x440
1200x1300x440
90
120
180
Weight approx.
TECHNICAL FEATURES
Has the capacity to process waste between 50-300 lt/h with Neutralab standard products. For more waste processing, further project designing is needed.
At places where the waste inlet levels are different, a different pressurization device is provided.
Has a discharging system to dispose processed waste into the sewerage.
Waste processing is done automatically.
Measurement parameters (pH, mV, temperature) can be monitored continuously.
Ventilation system is available.
Has an alarm system for any liquid leakage. Can operate during continuous liquid flow.
The case is movable and resistant to corrosion.
Operates at 220 V 50 Hz.
The disinfectant concentration (Chlorine+Ozone) and the disinfectant contact time can be adjusted by a control
unit on the device. Thus, proper concentration and contact time according to the features of the waste can be
specified.
While working with high concentration, automatic disenfectant removal (dechlorination) can be done.
In case the pH value of the processed waste is not proper to the accepted criteria, the system automatically adjusts pH values
The waste inlets and outlets are easy to operate (can be done with one hand). During installation or uninstallation operation, there is no leaking or dripping at the connecting ports.
In case the chemicals used in the device are below a specified level, the system is equipped with audio and video
warning.
The device has an external sampling unit.
CHEMICALLY POLLUTED AND INFECTIOUS LIQUID/SLUDGE WASTE DISINFECTING AND
PURIFICATION SYSTEM
A
spe-
cifically designed system as below can be designed and manufactured according
to the exact needs
[email protected]
www.metan.com.tr
+90.532.454 9077
METAN
ANTIBACTERIAL WALL PAINT
General purpose , low cost, silicone based , mat, anti-bacterial paint , Effective for 4 kinds
of representative bacteria
2. General purpose, low-cost , water based, semi-mat, anti-bacterial paint , Effective for 4
kinds of representative bacteria
3. Special purpose, semi-mat, water based anti-bacterial paint , Effective for 9 kinds of representative bacteria ( suitable for ceilings for OR , Intensive care rooms )
HOSPITALS, CLINICS , BLOOD CENTERS
DISPANSERY UNITS ,GERIATRIC HOUSES
SCHOOLS, RESTAURANTS, HOTELS
99.9 % INACTIVATION
GOVERNMENTAL HOUSES, HOMES
EFFICACY
ZOOS, VETERINARY HOUSES,
ALL BIOCIDAL CERTIFIED
EFFECTIVE FOR 2 YEARS FROM APPLICATION
Services
NO CHANCE ANYMORE FOR THE BELOW AND SO MANY OTHER
LIFE THREATENING AGENTS
[email protected]
www.metan.com.tr
+90.532.454 9077
METAN
PRF-FABRICATED MODALIIES
WE CAN DESIGN AND OFFER MOVABLE, STATIONARY OR FIELD KIND OF CLINICS AND HOSPITALS,
COMMODITY ACCOMODATION , CAMPS AND SIMILAR SOLUTIONS SUIT TO SPECIFIC NEEDS
TURN-KEY WITH THE MEDICAL AND AUXILLARY EQUIPMENT OR ONLY THE MUODULES CAN BE
DELIVERED
[email protected]
www.metan.com.tr
+90.532.454 9077
HOSPITAL Laboratory
Equipment
From
SÜMER / METAN
GYNAECOLOGY AND
INFANT / BABY CARE PRODUCTS
Breastmilk Storage cabinet
Breastmilk Freezer
Breastmilk
Storage / Freezer ( Combined )
Breastmilk Heater
Breastmilk Bag Heater
BLOODBANK REFRIGERATORS
GYNAECOLOGY CHAIRS
You may please ask for further needs
[email protected]
www.metan.com.tr
+90.532.454 9077
Injector Heater
HOSPITAL Laboratory
Equipment
From
SÜMER / METAN
LABORATORY AND HOSPITAL
STEAM STERILIZERS AND COMBINED
WASHING MACHINES & STERILIZERS
Vertical Type Steam Sterilizer
Prismatic Type Steam Sterilizer Single –Double Sliding Door
Prismatic Type Steam Sterilizer Sliding Door / Side Panel
Washing and Sterilization Device
Bottle Washing and Sterilization Device
Washing and Steam Sterilizer Flywheel Cover
[email protected]
www.metan.com.tr
+90.532.454 9077
8. Cad. 29. Sok. No: 38/A 06510 Emek-Ankara-Turkey
Tel: +90(312) 2121281 Fax: +90(312) 215 6069
Ugur Mumcu Cad. 17/10 Narlidere -Izmir
Tel/Fax:+90(232)238 7083
[email protected]
www.metan.com.tr
COMPANY PROFILE OF METAN GENERAL INFORMATION Name : METAN Green Health & Environmental Engineering & Consultancy Co. Ltd Year of Establishment : 18.03.1998 Founder : Dr. Cemal KALDIRIMCI Address: : Ankara Office; Emek Mahallesi 29. Sokak No: 38, Cankaya – Ankara, TURKEY Tel: +90.312.2121281, Fax:+90.312.2156069 e‐mail: [email protected] URL:www.metan.com.tr : Izmir Office: Ataturk Mahallesi Ugur Mumcu caddesi No: 17/10 Narlidere‐Izmir, TURKEY Tel/Fax: +232.2387083 Chamber of Commerce ID: : Ankara Chamber of Commerce, Registry No: 137971 Key Persons: : Partner : Mehmet Hocaoglu, Industrial Engineer, Marketing Manager for commodity products Kemal Hamamizade, Mechanical Engineer, Service Manager responsible for installations Dr. Gulbin Seybizinli ( Advisor, Medical doctor ) Bank references : Ankara, Sekerbank, Dikmen branch ; Ankara, Is bankasi, Maltepe Branch Strategic Partners : Below ones are those Metan cooperates on routine basis Satis Medical Co. ( www.satismedikal.com.tr ) (Medical supplies, healthcare equipment distributorship and supply) Cypherturk, ( www.cypherturk.com) (Environmental products distributorships supply and engineering) PRINCIPAL ACTIVITIES A) HEALHTCARE LINE 1‐Healthcare waste management and disposal Healthcare waste management has been one of the core businesses in the company since 1999. During establishment, the main task of Metan has been to initiate the culture and methodologies in the field of “Medical Waste Management Consultancy and Disposal Engineering “. The activities in this field has started with consultancy work in cooperation with EtLog GmbH Germany and continued with distributorship of major companies form Europe and USA as Ecodas, Tuttnauer, Matachane and Bond tech , etc. and finally with Logmed GmbH owned by Globetech Environment, USA. Kayseri, Konya and Kusadasi projects were contracted during this period. After Logmed GmbH announced bankruptcy ( during the global crisis, Globetech Environment lost in public lists in the USA ) , Metan decided to start manufacturing of medical waste sterilizers and the founder, Dr. Cemal Kaldirimci set up another company with the name of Optimet Engineering Co. and developed her own and unique design. The first product was set up in Afyon city. Adana, Kirikkale and N. Cyprus projects followed the first one and the last one contracted was Romania project. Kirikkale project was a BOT project covering waste collecting, logistics and treatment steps which is still ongoing. After Optimet had decided to stop manufacturing, Akar Co. , which is the leading autoclave manufacturing company copied the design of Dr. Cemal Kaldirimci , developed, added her engineering concept and launched into market Akar brand sterilizers . ( L type , the design of Dr. Cemal Kaldirimci ) Metan has been the exclusive international marketing company for Akar Co. for one year and during this period, Urfa project was realized. Currently Metan has been acting as up both a consulting and EPC company mainly in African and Gulf countries in healthcare waste management and field and has been using the proper products in her International projects. Meanwhile, Some projects for KfW and Gtz have been conducted by. Dr. Cemal KALDIRIMCI as the local expert ( Bursa, Nevsehir ) 2‐ Liquid Hospital waste management and disposal The grey and black water from hospitals, whether infectious or not, require controlling and treating properly. Metan has been acting as consulting and project management and Execution Company with regard to liquid healthcare waste. Metan is offering liquid medical waste neutralizer and disinfecting unit as well as total chemical and infectious treatment and purification systems. 3‐ Anti‐bacterial hospital and wall paint business Metan is currently the authorized marketing company of one of the leading paint manufacturers in Turkey, Sartas Paint Inc. Anti‐bacterial paint has been launched into market as an innovative product. and Metan has been qualified as the international marketing company. The cooperation started in late 2014 and currently the dealer network is being set up. 4‐ Mobile Field Hospital and Health Clinics business Mobile clinics and hospitals are rather new solutions providing quick services under emergency and combat conditions and at particularly the rural areas where stationary services are not so possible. Metan is in cooperation with major Turkish field clinics manufacturer and designing and installing the turn‐key solutions furnished with medical equipment. 5‐ Export of Hospital autoclaves, washing– sterilizing equipment, blood and laboratory cabinets, and hospital furniture Sumer Inc. is one of the most leading healthcare equipment manufacturer in Turkey and Metan has the export rights for the products made by Sumer. Metan has also been acting as consulting company to Sumer for product development and manufacturing. 6‐ Package Trading and tender business Metan has a large portfolio of healthcare equipment and material manufacturers from all over the world and with this wide portfolio and vise experience, is capable to perform the package project design and execution and also in tender business in and outside Turkey. B. ENVIRONMENTAL LINE 1‐Hazardous waste management and treatment Metan has been involved in the managing, storing and disposal activities of hazardous healthcare waste and hazardous industrial waste. The founder, Dr. Cemal Kaldirimci has set up a hazardous waste interim storage facility in Izmir city with the company name of Eko Waste Engineering Inc. which is still active in this field. Currently Metan has been using the incinerators from Santes Co., Turkey in the international EPC and commercial projects. 2‐Scrap plastic and scrap tire treatment and recycling line In this line, Metan is cooperating with selected suppliers in pyrolysis technologies field and to set up turn‐key plants to recover and purify steel, oil, power and carbon black from scrap tires. This industry is very fragile and there are numerous numbers of suppliers in the scrap tire and plastics pyrolysis line but only some of them are reliable and qualified by all means. One of the main concerns in this industry is firing danger and outmost care must be given in selecting the technology provider and method. Metan has spent quite a long time to choose the best technology providers in pyrolysis, product refinery and pre‐treatment lines. 3‐ Renewable Energy Sector, PV Solar Power to Energy Systems Metan has entered into the renewable energy sector in cooperation with Turk Res Solar Co. and some other suppliers from various countries. Metan is now offering turn‐key solar farms and also designing and offering street solar light systems, residential off‐grid systems, solar and wind‐solar hybrid systems which are tailor‐made according to the demands. Solid waste to power, municipal waste treatment for power generation, biomass to power, e‐waste recycling are other areas which Metan assists her clients with most proper technologies worldwide. 4‐ Potable Water and Waste Water Management and Treatment Metan has been offering to her clients , stationary and containerized potable water purification and desalination facilities working on resins, filtering and reverse osmosis methods and also can combine the facility with solar PV systems to be self‐sufficient in energy. Also, small to large size water purification and disinfecting tools and devices, equipment are provided from selected suppliers. In this line, project‐base cooperation with Major Turkish, Italian and German suppliers have been established. Further, stationary and containerized water bottling systems are combined with water purification systems. Also, waste water treatment bacteria, water remediation agents, soil stabilizers are traded in cooperation with various companies from Eastern and Western countries. 5‐Road and Building Security line Metan is offering the full line of hydraulic road blockers, hydraulic assassination traps, hydraulic road bollards, tire killers and turnstile systems made by one of the major manufacturers in Turkey. 6‐ Small to Medium capacity Work Machinery As many project applications require during handling, unloading, operation, etc. having small size work machinery on the ground. This is why we are offering various equipment in this category. 7‐ General Project Design, Development, Execution As having a very wide range experience in laboratory , healthcare , industrial, environmental , waste management and energy sectors, Metan is supplying her clients with various system solutions and products in their needs.( the last two projects performed are LPG Cylinder manufacturing plant and LPG gas filling station projects for Nigeria ) C‐ HUMANITARIAN AND SOCIAL RESPONSIBILITY WORKS Founder of Metan, Mr. Dr. Cemal Kaldirimci has been selected as the Country Representative and Advisory Board Member of AFRIEF, Africa Islamic Economy Foundation. Under this position, various humanitarian projects in housing, accommodation, potable water and waste water management, energy generation, waste management from the smart city perspective are being designed, developed and implemented. Date: 18.01.2016 Dr. Cemal Kaldirimci ( Managing Director , Founded Owner ) SUMMARY OF THE PRODUCTS AND SERVICES WE CAN SUPPLY TOGETHER WITH OUR CONTRACTED PARTNERS preferably FROM TURKEY AND ALSO FROM OTHER COUNTRIES PLEASE KINDLY NOTE THAT WE CAN PROCESS ANY OF YOUR SIMILAR INQUIRIES AND MAKE YOUR PROJECT AVAILABLE FOR YOU YOU MAY PLEASE INQUIRE US WITH ANY OF YOUR PROJECT FOR OUR REVIEW METAN Green Health & Environmental Engineering & Consultancy Services
HEALTHCARE WASTE
MANAGEMENT AND DISPOSAL OF
BIO-MEDICAL WASTE
Healthcare waste is Segregated as follows
Healthcare Waste
(100 %)
Non-Risk Waste
Risk Waste
( 80 %)
( 20 %)
Refuse
( 40 %)
Recycling
( 40 %)
Bio-Medical
Waste
Chemical Waste
Other Waste
( 5 %)
( 0,5 %)
• Photo-Chemicals
• Pharmaceuticals
•Other Chemical w.
• Radioactive w.
• Cytotoxic w.
( 14,5 %)
• Infectious w.
• Hospital w.
• Pathological w.
METAN
WASTE OPERATORS NEED TO KNOW HOW TO TREAT
DIFFERENT WASTE STREAMS ARISEN FROM MEDICAL
SERVICES BY THE HEALTH CENTERS
WE REVIEW YOUR NEEDS AND OFFER YOU THE MOST APPROPRIATE
SOLUTION SUITS TO YOUR NEEDS
Pre-shredding kind ( We have various solutions from 50 kg/h to 750 kg/h ,
Smaller capacities are under development )
Post-shredding kind ( We have various solutions from 75 kg/h to 1000 kg/h ,
Higher capacities on demand )
[email protected]
www.metan.com.tr
+90.532.454 9077
METAN
LIQUID MEDICAL WASTE DESENFECTING AND NEUTROLIZING
EQUIPMENT
Liquid discharge form laboratory equipment may be
contaminated and infectious at relatively low to medium
levels.
SPECIALLY DESIGNED EQUIPMENT WOULD DISINFECT AND
PURIFY THESE KIND IF LIQUID WASTES.
BASIC FEATURES, CE
Minimizes human-induced errors.
Has high safety standards.
Has the same disinf ection efficiency at every discharge (Disinfection capacity can be increased up to 99.99%).
Makes automatic pH adjustment
Decharges the wastes into the sewerage system after processing them as specified in the regulations.
Does not require a comprehensive infrastructure and/or modification to install and operate.
Can be operated in a lab provided that adequate ventilation system exists.
Could be an economical solution due to low investment and operational costs.
MODEL 25
Waste Processing Capacity, (L/h) max.
75
MODEL 50
MODEL 100
150
300
Disinfection Chemical
Chlorine based disinfectants and ozone
Disinfection Constrate
0.1 ppm - 5.0 ppm / 5.0 ppm - 5.000 ppm (10g/lt in special applications)
pH Regulator
Sodium Hydrogene Sulphade, Hydrochloride Acid, Sodium Carbonate, Sodium Hydroxide
Power (k W)
0.10
Voltage(v/Hz)
Size- heigh x depth x width(mm)
0.12
0.20
230/50
820x800x440
820x1250x440
1200x1300x440
90
120
180
Weight approx.
TECHNICAL FEATURES
Has the capacity to process waste between 50-300 lt/h with Neutralab standard products. For more waste processing, further project designing is needed.
At places where the waste inlet levels are different, a different pressurization device is provided.
Has a discharging system to dispose processed waste into the sewerage.
Waste processing is done automatically.
Measurement parameters (pH, mV, temperature) can be monitored continuously.
Ventilation system is available.
Has an alarm system for any liquid leakage. Can operate during continuous liquid flow.
The case is movable and resistant to corrosion.
Operates at 220 V 50 Hz.
The disinfectant concentration (Chlorine+Ozone) and the disinfectant contact time can be adjusted by a control
unit on the device. Thus, proper concentration and contact time according to the features of the waste can be
specified.
While working with high concentration, automatic disenfectant removal (dechlorination) can be done.
In case the pH value of the processed waste is not proper to the accepted criteria, the system automatically adjusts pH values
The waste inlets and outlets are easy to operate (can be done with one hand). During installation or uninstallation operation, there is no leaking or dripping at the connecting ports.
In case the chemicals used in the device are below a specified level, the system is equipped with audio and video
warning.
The device has an external sampling unit.
CHEMICALLY POLLUTED AND INFECTIOUS LIQUID/SLUDGE WASTE DISINFECTING AND
PURIFICATION SYSTEM
A
spe-
cifically designed system as below can be designed and manufactured according
to the exact needs
[email protected]
www.metan.com.tr
+90.532.454 9077
METAN
ANTIBACTERIAL WALL PAINT
General purpose , low cost, silicone based , mat, anti-bacterial paint , Effective for 4 kinds
of representative bacteria
2. General purpose, low-cost , water based, semi-mat, anti-bacterial paint , Effective for 4
kinds of representative bacteria
3. Special purpose, semi-mat, water based anti-bacterial paint , Effective for 9 kinds of representative bacteria ( suitable for ceilings for OR , Intensive care rooms )
HOSPITALS, CLINICS , BLOOD CENTERS
DISPANSERY UNITS ,GERIATRIC HOUSES
SCHOOLS, RESTAURANTS, HOTELS
99.9 % INACTIVATION
GOVERNMENTAL HOUSES, HOMES
EFFICACY
ZOOS, VETERINARY HOUSES,
ALL BIOCIDAL CERTIFIED
EFFECTIVE FOR 2 YEARS FROM APPLICATION
Services
NO CHANCE ANYMORE FOR THE BELOW AND SO MANY OTHER
LIFE THREATENING AGENTS
[email protected]
www.metan.com.tr
+90.532.454 9077
METAN
PRF-FABRICATED MODALIIES
WE CAN DESIGN AND OFFER MOVABLE, STATIONARY OR FIELD KIND OF CLINICS AND HOSPITALS,
COMMODITY ACCOMODATION , CAMPS AND SIMILAR SOLUTIONS SUIT TO SPECIFIC NEEDS
TURN-KEY WITH THE MEDICAL AND AUXILLARY EQUIPMENT OR ONLY THE MUODULES CAN BE
DELIVERED
[email protected]
www.metan.com.tr
+90.532.454 9077
HOSPITAL Laboratory
Equipment
From
SÜMER / METAN
GYNAECOLOGY AND
INFANT / BABY CARE PRODUCTS
Breastmilk Storage cabinet
Breastmilk Freezer
Breastmilk
Storage / Freezer ( Combined )
Breastmilk Heater
Breastmilk Bag Heater
BLOODBANK REFRIGERATORS
GYNAECOLOGY CHAIRS
You may please ask for further needs
[email protected]
www.metan.com.tr
+90.532.454 9077
Injector Heater
HOSPITAL Laboratory
Equipment
From
SÜMER / METAN
LABORATORY AND HOSPITAL
STEAM STERILIZERS AND COMBINED
WASHING MACHINES & STERILIZERS
Vertical Type Steam Sterilizer
Prismatic Type Steam Sterilizer Single –Double Sliding Door
Prismatic Type Steam Sterilizer Sliding Door / Side Panel
Washing and Sterilization Device
Bottle Washing and Sterilization Device
Washing and Steam Sterilizer Flywheel Cover
[email protected]
www.metan.com.tr
+90.532.454 9077
HAZARDOUS WASTE MANAGEMENT AND DISPOSAL TECHNOLOGIES
According to the EPA, hazardous waste is any solid, gaseous, liquid or sludge waste that is potentially harmful to public
health and the environment.
All of these substances pose significant health risks to human, animals and the environment.
Most industrial plants and manufacturing concerns generate hazardous waste that requires the use of proper disposal techniques.
Correctly disposing of the hazardous waste is crucial to maintaining national and global health
BASIC SYMBOLS
• Examples of industrial hazardous waste that require
special disposal processes include:
•
•
•
•
•
•
•
•
•
•
•
MANAGEMENT OF HAZARDOUS WASTE
Starts from Point of Generation
Ends up with Re-Use, Re-Cycling, Disposal
AT THE POINT OF GENERATION
REDUCE
REUSE
RECYCLE
is tried as much as possible in a safe maner
Analyzing, Sorting, Labeling, Containerization
Inventory and Record Keeping,
Temporary storage
Spil Control
Tranfer to permanet disposal-recycling
Reporting to the Authorities
Spent solvent wastes
Wastes from wood preserving
Petroleum refinery wastewater treatment sludge
Multisource leachate
Dioxin bearing wastes
Inorganic pigment & organic chemicals manufacturing
Explosives manufacturing inputs and byproducts
Coking
Iron & steel production byproducts
Pesticides manufacturing processes
Primary aluminum production
Storing Hazardous Waste
Hazardous waste is stored for a temporary period before it is treated, disposed or stored
elsewhere. Hazardous waste is stored in containers, tanks, waste piles, containment buildings
and surface impoundments.
A container is a portable device in which the hazardous waste can be stored, treated, disposed
or otherwise handled.( Example: 55-gallon drum.)
A waste pile is an open, uncontained waste pile used for storing or treating waste. The waste is
placed on top of a double liner system to prevent groundwater contamination from the waste
leachate.
Tanks are stationary devices made of non-earthen materials like steel, glass or concrete and
are used to treat or store hazardous waste.
Containment buildings are self supported, completely enclosed structures used to treat or
store non-containerized hazardous waste.
Surface impoundments are man-made excavations such as a lagoon or storage pit lined by
synthetic liners.
EPA identifies 4 ways to recycle hazardous waste:
Use constituting disposal
Reclamation
Direct use and reuse
Combustion for energy recovery
Hazardous waste can be recycled by being applied elsewhere, for example used as fertilizer.
Some wastes can be incorporated into another product, for example, used to make asphalt. The
recycling of these hazardous wastes in these ways is known as use constituting disposal.
Reclamation
By contrast, reclamation involves processing a waste to recover usable component. An example
of reclamation would be recovering mercury from broken thermometers. Spent (used) solvents,
such as acetone, can be distilled to make them pure again. Metals, such as lead, may also be
reclaimed from other materials, such as paint and lead-acid batteries.
Direct use or reuse
Direct use or reuse involves using a waste directly as an ingredient to make a product or a
substitute for a product. For example, latex paint can be mixed with ash to make cement mix for
concrete.
Combustion for Energy Recovery
Combustion for energy recovery is the use of wastes directly as a fuel or as an ingredient to
produce heat. For example, oily wastes can be used to generate steam or electricity.
Disposal techniques include, but are not limited to:
Incineration.
This process has undergone extensive technological advances that
fully comply with regulatory standards.
Landfill disposal.
With underground barriers, this method is considered
environmentally viable, as hazardous substances are caught before they seep into
the ground. DOT certified waste management workers arrive onsite, properly label
and store your waste in regulatory storage tanks and safely transport the materials
to the landfill site for disposal.
Concrete mixing.
To stabilize or solidify certain toxic substances, some waste
management operations mix a specific concrete concoction with the hazardous
material.
WE CAN PROVIDE YOU WITH COMPLETE SOLUTIONS FROM



HAZARDOUS WASTE SORTING FACILITIES, STORAGE AREA DESIGN AND SET-UP , TRANSPORT
TRUCKS
AND STATE OF THE ART
INCINERATORS FOR HAZARDOUS WASTE
ANIMAL INCINERATORS
MEDICAL WASTE INCINERATORS
[email protected]
www.metan.com.tr
+90.532.454 9077
SCRAP PLASTIC and TIRE RECYCLING
END OF LIFE TIRES AND USED PLASTICS ARE NEVER EVER WASTE AND NOT TO BE DISPOSED OF TO LANDFILL BUT ARE CONSIDERED TO BE VALUABLE SOURCES FOR RECYCLING AND ARE TO BE TREATED ADEQUATELY TO GET BENEFIT OUT OF THEM.
THE BEST METHOD FOR REYCLING OF USED PLASTICS IS SEGREGATING ON SOURCE
ONCE PLASTICS ARE MIXED UP WITH OTHER KINDS OF WASTE STREAMS, IT BECOMES
MORE
COMPLICATED AND COSTLY TO SEGREGATE THE PLASTICS FROM OTHER MATERIALS AND
FURTHER TO SEPERATE THEM INTO SORTS
WE CAN PROVIDE OUR CLIENTS WITH THE ENTIRE RANGE FOR RECYCLING EQUIPMENT
FOR PRODUCTION OF PLASTIC GRANULES
A TYPICAL “ USED PLASTICS “ PHYSICAL RECYCLING SYSTEM IS SHOWN BELOW WHICH
WE CAN DELIVER MEETING THE NEEDS
OR WE CAN ALSO DELIVER PYROLYSIS SYSTEMS TO GENERATE OIL AND POWER FROM
USED PLASTICS AS DESCRIBED BELOW IN THE PYROLYSIS OF “ END OF LIFE TIRES “
END OF LIFE TYRES CONSISTS OF VALUABLE MATERIALS AS STEEL, RUBBER AND
CARBON BLACK WHICH ARE TO BE RECOVERED BY PHYSICAL AND CHEMICAL
WAYS.
Composition by weight of tires
Material
Rubber/elastomersa
Car/utility%
±48
Truck/lorry%
±45
Carbon black or silicab
Metal
±22
±15
±22
±25
Textile
±5
-
Zinc oxide
Sulphur
±1
±1
±2
±1
Additives
±8
±5
A Truck tyres contain proportionately more natural rubber in comparison to synthetic rubber than do car tyres
b Different varieties of carbon black are used for different purposes and may appear in other categories of material
The rubber compounds, metals and textiles are recovered through material recycling
WE CAN DESIGN AND DELIVER THE MOST APPROPRIATE AND COMPETITIVE
SCRAP TIRE AND PLASTICS PYROLYSIS SYSTEMS FOR ANY NEEDS FOR THE
RECOVERY OF CRUDE OIL, REFINED OIL, AND POWER ( CARBON BLACK AND
STEEEL IN TIRES PYROLYSIS )
[email protected]
www.metan.com.tr
+90.532.454 9077
MORE
WAYS.
Material
Rubber/elastomersa
Car/utility%
±48
Truck/lorry%
±45
Metal
±22
±15
±22
±25
Textile
±5
-
Zinc oxide
Sulphur
±1
±1
±2
±1
Additives
±8
±5
[email protected]
www.metan.com.tr
+90.532.454 9077
R
ENEWABLE ENERGY SOURCES AS SUN, WIND, WASTE AND BIOMASS etc. ARE THE VALAUBALE SOURCED TO BE USED FOR POWER GENERATION WITHOUT DESTROYING AND DAMAGING THE
ENVIRONMENT AND GIVING ANY HAZARD TO HUMAN, ANIMAL AND PLANT LIVES.
METAN HAS BEEN PROVIDING MAINLY PV SOLAR POWER SYTEMS , WIND & SOLAR HYBRID SYSTEMS FOR
INDUSTRIAL, RESIDENTIAL AND COMMERCIAL USES.
WE ARE USING SELECTED AND COMPETIVE MANUFACTURERS AND SYSTEM DESIGNERS SUIT TO THE
NEEEDS OF THE CLIENTS.
PV SOLAR FARMS UNDER EPC CONTRACTS
CONDENSED SOLAR SYSTEMS
SOLAR / WIND HYBRID SYSTEMS FOR RESIDENTIAL USES
ON-GRID AND OFF-GRID RESIDENTIAL SYSTEMS
INDUSTRIAL AND COMMERCIAL SOLAR INSTALLATIONS
[email protected]
www.metan.com.tr
+90.532.454 9077
WATER DISINFECTING AND PURIFICATION TECHOLOGIES for VARIOUS
APPLICATIONS
WATER PURIFICATION and DISINFECTION

SAFE DRINKING WATER , INTERVENTIONS FOR
HOME AND OUTSIDE USE

PERSONAL USE

FAMILY USE

COMMODITY USE
USED FOR DIRTY AND CONTAMINATED WATER FROM ANY SOURCE
FOR BOTH CLEANING AND DISINFECTING , FOR SAFE DRINK
AWARD WINNING SOLAR
WATER DISINFECTING
EQUIPMENT
SILVER RODS FOR DISINFECTING THE WATER IN BOTTLES AND TANKS
WATER PURIFICATION AND DISINFECTING TECHNOLOGIES
for
INDUSTRIAL AND COMMERCIAL USES
Mobile water treatment systems
Water treatment systems for purification of tap water or ground water that produce
high class potable water, treatment systems for ground water purification which produces water intended for irrigation, treatment systems for water contaminated by radioactive elements, water treatment systems and tertiary treatment plants for buildings and
housing estates allowing for re-introduction of the same water into circulation systems
allowing abstracting water in places with underdeveloped infrastructure, solving problems of access to potable water on areas with high water.
Applied for ground water, brackish water,
lake water, river water and seawater




CIVIL AND MILITARY
PURPOSES
WATER WELLS
RIVERS
LAKES
SEAWATER
REVERSE OSMOSIS INDUSTRIAL WATER PURIFICATION
AND DESALINATION SYSTEMS
POWER FROM SOLAR AND/OR WIND IS
ALSO POSSIBLE
WATER BOTTLING PLANTS CAN BE CONFIGURED
ACCORDING TO THE ;
CAPACITY OF WATER SOURCE
WITH OR WITHOUT GAS AND SYRUP OPTIONS
BOTTLE KIND AND SIZE
[email protected]
www.metan.com.tr
+90.532.454 9077
ROAD SECURITY SYSTEMS
SURFACE ROAD BLOCKERS
HYDRAULIC RISING ROAD BLOCKERS
Road blockers are designed especially for entrance points which have a threat of
vehicle attack or for the ones that have high security requirements. If there is a
threat of vehicle attack in addition to the control of vehicle access in high
security applications, hydraulic road blockers are the unique solution and the
most secure systems.
ELECTROMECHANICAL
TYRE-KILLER
Electromechanical Tyre-Killer is one of the highest
security vehicle access control systems. The TyreKiller provides high security for sensitive areas
HYDRAULIC ROAD BOLLARDS
Hydraulic bollards are used in places that requires higher security, in conditions that requires controlled entrance
and exit of vehicles, in places that vehicle passing is not authorized. A vehicle collision occurs; bollards will destroy with the horizontal bearing system, the important parts of the vehicle system so that vehicle will not move. According to road width, hydraulic bollards are manufactured at desired dimensions. Its production types are done by
hydraulically and pneumatically.
[email protected]
www.metan.com.tr
+90.532.454 9077
SMALL TO MEDIUM DUTY WORK MACHINERY
FOR FARMING, CONSTRUCTION, TRANSPORTATION, HIGHWAY , MINING ,
LOADING-UNLOADING INDUSTRIES
MINI DUMPER
SKID STEEL LOADERS
ARTICULATED LOADERS
ACCESSORIES
AND CUSTOM DESIGNS FOR SPECIAL NEEDS
[email protected]
www.metan.com.tr
+90.532.454 9077
AFRICA ISLAMIC ECONOMIC FOUNDATION
Al - Furqan Building, Behind Village Water Reservoirs,
Lamashegu, P. O. Box ER 516,
Tamale, Northern Region.
Tel: +233 243 65 54 46, +233 244 48 57 48
E-mail: [email protected], [email protected]
Website: www.afrief.com
12/06/2015
AFRIEF/TK/01-2015
TO WHOM IT MAY CONCERN
It is an honour for me to introduce DR CEMAL KALDIRIMCI, of Metan Green Health & Environment
Services, Ankara, Turkey, as a member of the International Advisory Board and a Special
representative of the Africa Islamic Economic Foundation in the Republic of Turkey.
The Africa Islamic Economic Foundation (AFRIEF) is a growing organization that works to foster
Islamic Economics and Finance, Halal Economy and ethical investments in Africa. AFRIEF is registered
with the Government of Ghana and networks with Governments, public and private sector
organizations at national and international levels. Operating from its headquarters in Ghana, AFRIEF
works for human development, promotion of better opportunities, improving standards of living and
provides support to Governments, business and social sector organizations for smooth
implementation of their projects.
AFRIEF has launched the Innovative Partnerships for Economic Growth in Africa as an initiative to
collaborate with African Governments and the private sector to create a strong and competitive
economy in Africa. Accordingly the Initiative has identified Smart Cities, Halal Economy, SMEs and
Entrepreneurship as strategic sectors which have major economic potential and capable of
generating economic growth, more employment and increased foreign earnings.
Our strategy is to create synergies among players operating in the above sectors, namely,
Governments, Utilities, Industries and Clusters, Academic and Research Institutions, Investors and
Entrepreneurs, Commercial and Investment banks, Multilateral and Bilateral financial institutions to
accelerate the roll out of viable commercial and industrial projects, integrating green and smart
technologies across Africa. You may please visit our website (www.afrief.com) for more information
about the Initiative.
We believe in developing mutually beneficial relationships. Accordingly, we would be glad if you will
kindly grant audience to Dr Cemal Kaldirimci to discuss with you about the possibility of establishing
a collaboration between AFRIEF and your company for the purpose of implementing projects,
sharing knowledge and best practices under the Initiative in Africa. We believe that your expertise
and years of experience in the sectors will bring considerable benefit to the Initiative and the people
of Africa.
While looking forward to hearing from you soon, may you please accept our warmest regards and
best wishes.
Sincerely Yours
Baba Yunus Muhammad
President
HAZARDOUS WASTE MANAGEMENT AND DISPOSAL TECHNOLOGIES
According to the EPA, hazardous waste is any solid, gaseous, liquid or sludge waste that is potentially harmful to public
health and the environment.
All of these substances pose significant health risks to human, animals and the environment.
Most industrial plants and manufacturing concerns generate hazardous waste that requires the use of proper disposal techniques.
Correctly disposing of the hazardous waste is crucial to maintaining national and global health
BASIC SYMBOLS
• Examples of industrial hazardous waste that require
special disposal processes include:
•
•
•
•
•
•
•
•
•
•
•
MANAGEMENT OF HAZARDOUS WASTE
Starts from Point of Generation
Ends up with Re-Use, Re-Cycling, Disposal
AT THE POINT OF GENERATION
REDUCE
REUSE
RECYCLE
is tried as much as possible in a safe maner
Analyzing, Sorting, Labeling, Containerization
Inventory and Record Keeping,
Temporary storage
Spil Control
Tranfer to permanet disposal-recycling
Reporting to the Authorities
Spent solvent wastes
Wastes from wood preserving
Petroleum refinery wastewater treatment sludge
Multisource leachate
Dioxin bearing wastes
Inorganic pigment & organic chemicals manufacturing
Explosives manufacturing inputs and byproducts
Coking
Iron & steel production byproducts
Pesticides manufacturing processes
Primary aluminum production
Storing Hazardous Waste
Hazardous waste is stored for a temporary period before it is treated, disposed or stored
elsewhere. Hazardous waste is stored in containers, tanks, waste piles, containment buildings
and surface impoundments.
A container is a portable device in which the hazardous waste can be stored, treated, disposed
or otherwise handled.( Example: 55-gallon drum.)
A waste pile is an open, uncontained waste pile used for storing or treating waste. The waste is
placed on top of a double liner system to prevent groundwater contamination from the waste
leachate.
Tanks are stationary devices made of non-earthen materials like steel, glass or concrete and
are used to treat or store hazardous waste.
Containment buildings are self supported, completely enclosed structures used to treat or
store non-containerized hazardous waste.
Surface impoundments are man-made excavations such as a lagoon or storage pit lined by
synthetic liners.
EPA identifies 4 ways to recycle hazardous waste:
Reclamation
Direct use and reuse
Combustion for energy recovery
Hazardous waste can be recycled by being applied elsewhere, for example used as fertilizer.
Some wastes can be incorporated into another product, for example, used to make asphalt. The
recycling of these hazardous wastes in these ways is known as use constituting disposal.
Reclamation
By contrast, reclamation involves processing a waste to recover usable component. An example
of reclamation would be recovering mercury from broken thermometers. Spent (used) solvents,
such as acetone, can be distilled to make them pure again. Metals, such as lead, may also be
reclaimed from other materials, such as paint and lead-acid batteries.
Direct use or reuse
Direct use or reuse involves using a waste directly as an ingredient to make a product or a
substitute for a product. For example, latex paint can be mixed with ash to make cement mix for
concrete.
Combustion for Energy Recovery
Combustion for energy recovery is the use of wastes directly as a fuel or as an ingredient to
produce heat. For example, oily wastes can be used to generate steam or electricity.
Disposal techniques include, but are not limited to:
Incineration.
This process has undergone extensive technological advances that
fully comply with regulatory standards.
Landfill disposal.
With underground barriers, this method is considered
environmentally viable, as hazardous substances are caught before they seep into
the ground. DOT certified waste management workers arrive onsite, properly label
and store your waste in regulatory storage tanks and safely transport the materials
to the landfill site for disposal.
Concrete mixing.
To stabilize or solidify certain toxic substances, some waste
management operations mix a specific concrete concoction with the hazardous
material.
WE CAN PROVIDE YOU WITH COMPLETE SOLUTIONS FROM



HAZARDOUS WASTE SORTING FACILITIES, STORAGE AREA DESIGN AND SET-UP , TRANSPORT
TRUCKS
AND STATE OF THE ART
INCINERATORS FOR HAZARDOUS WASTE
ANIMAL INCINERATORS
MEDICAL WASTE INCINERATORS
[email protected]
www.metan.com.tr
+90.532.454 9077
MORE
WAYS.
Material
Rubber/elastomersa
Car/utility%
±48
Truck/lorry%
±45
Metal
±22
±15
±22
±25
Textile
±5
-
Zinc oxide
Sulphur
±1
±1
±2
±1
Additives
±8
±5
[email protected]
www.metan.com.tr
+90.532.454 9077
MORE
WAYS.
Material
Rubber/elastomersa
Car/utility%
±48
Truck/lorry%
±45
Metal
±22
±15
±22
±25
Textile
±5
-
Zinc oxide
Sulphur
±1
±1
±2
±1
Additives
±8
±5
[email protected]
www.metan.com.tr
+90.532.454 9077
R
ENEWABLE ENERGY SOURCES AS SUN, WIND, WASTE AND BIOMASS etc. ARE THE VALAUBALE SOURCED TO BE USED FOR POWER GENERATION WITHOUT DESTROYING AND DAMAGING THE
ENVIRONMENT AND GIVING ANY HAZARD TO HUMAN, ANIMAL AND PLANT LIVES.
METAN HAS BEEN PROVIDING MAINLY PV SOLAR POWER SYTEMS , WIND & SOLAR HYBRID SYSTEMS FOR
INDUSTRIAL, RESIDENTIAL AND COMMERCIAL USES.
WE ARE USING SELECTED AND COMPETIVE MANUFACTURERS AND SYSTEM DESIGNERS SUIT TO THE
NEEEDS OF THE CLIENTS.
PV SOLAR FARMS UNDER EPC CONTRACTS
CONDENSED SOLAR SYSTEMS
SOLAR / WIND HYBRID SYSTEMS FOR RESIDENTIAL USES
ON-GRID AND OFF-GRID RESIDENTIAL SYSTEMS
INDUSTRIAL AND COMMERCIAL SOLAR INSTALLATIONS
[email protected]
www.metan.com.tr
+90.532.454 9077
WATER DISINFECTING AND PURIFICATION TECHOLOGIES for VARIOUS
APPLICATIONS
WATER PURIFICATION and DISINFECTION

SAFE DRINKING WATER , INTERVENTIONS FOR
HOME AND OUTSIDE USE

PERSONAL USE

FAMILY USE

COMMODITY USE
USED FOR DIRTY AND CONTAMINATED WATER FROM ANY SOURCE
FOR BOTH CLEANING AND DISINFECTING , FOR SAFE DRINK
AWARD WINNING SOLAR
WATER DISINFECTING
EQUIPMENT
SILVER RODS FOR DISINFECTING THE WATER IN BOTTLES AND TANKS
WATER PURIFICATION AND DISINFECTING TECHNOLOGIES
for
INDUSTRIAL AND COMMERCIAL USES
Mobile water treatment systems
Water treatment systems for purification of tap water or ground water that produce
high class potable water, treatment systems for ground water purification which produces water intended for irrigation, treatment systems for water contaminated by radioactive elements, water treatment systems and tertiary treatment plants for buildings and
housing estates allowing for re-introduction of the same water into circulation systems
allowing abstracting water in places with underdeveloped infrastructure, solving problems of access to potable water on areas with high water.
Applied for ground water, brackish water,
lake water, river water and seawater




CIVIL AND MILITARY
PURPOSES
WATER WELLS
RIVERS
LAKES
SEAWATER
REVERSE OSMOSIS INDUSTRIAL WATER PURIFICATION
AND DESALINATION SYSTEMS
POWER FROM SOLAR AND/OR WIND IS
ALSO POSSIBLE
WATER BOTTLING PLANTS CAN BE CONFIGURED
ACCORDING TO THE ;
CAPACITY OF WATER SOURCE
WITH OR WITHOUT GAS AND SYRUP OPTIONS
BOTTLE KIND AND SIZE
[email protected]
www.metan.com.tr
+90.532.454 9077
ROAD SECURITY SYSTEMS
SURFACE ROAD BLOCKERS
HYDRAULIC RISING ROAD BLOCKERS
Road blockers are designed especially for entrance points which have a threat of
vehicle attack or for the ones that have high security requirements. If there is a
threat of vehicle attack in addition to the control of vehicle access in high
security applications, hydraulic road blockers are the unique solution and the
most secure systems.
ELECTROMECHANICAL
TYRE-KILLER
Electromechanical Tyre-Killer is one of the highest
security vehicle access control systems. The TyreKiller provides high security for sensitive areas
HYDRAULIC ROAD BOLLARDS
Hydraulic bollards are used in places that requires higher security, in conditions that requires controlled entrance
and exit of vehicles, in places that vehicle passing is not authorized. A vehicle collision occurs; bollards will destroy with the horizontal bearing system, the important parts of the vehicle system so that vehicle will not move. According to road width, hydraulic bollards are manufactured at desired dimensions. Its production types are done by
hydraulically and pneumatically.
[email protected]
www.metan.com.tr
+90.532.454 9077
SMALL TO MEDIUM DUTY WORK MACHINERY
FOR FARMING, CONSTRUCTION, TRANSPORTATION, HIGHWAY , MINING ,
LOADING-UNLOADING INDUSTRIES
MINI DUMPER
SKID STEEL LOADERS
ARTICULATED LOADERS
ACCESSORIES
AND CUSTOM DESIGNS FOR SPECIAL NEEDS
[email protected]
www.metan.com.tr
+90.532.454 9077
AFRICA ISLAMIC ECONOMIC FOUNDATION
Al - Furqan Building, Behind Village Water Reservoirs,
Lamashegu, P. O. Box ER 516,
Tamale, Northern Region.
Tel: +233 243 65 54 46, +233 244 48 57 48
E-mail: [email protected], [email protected]
Website: www.afrief.com
12/06/2015
AFRIEF/TK/01-2015
TO WHOM IT MAY CONCERN
It is an honour for me to introduce DR CEMAL KALDIRIMCI, of Metan Green Health & Environment
Services, Ankara, Turkey, as a member of the International Advisory Board and a Special
representative of the Africa Islamic Economic Foundation in the Republic of Turkey.
The Africa Islamic Economic Foundation (AFRIEF) is a growing organization that works to foster
Islamic Economics and Finance, Halal Economy and ethical investments in Africa. AFRIEF is registered
with the Government of Ghana and networks with Governments, public and private sector
organizations at national and international levels. Operating from its headquarters in Ghana, AFRIEF
works for human development, promotion of better opportunities, improving standards of living and
provides support to Governments, business and social sector organizations for smooth
implementation of their projects.
AFRIEF has launched the Innovative Partnerships for Economic Growth in Africa as an initiative to
collaborate with African Governments and the private sector to create a strong and competitive
economy in Africa. Accordingly the Initiative has identified Smart Cities, Halal Economy, SMEs and
Entrepreneurship as strategic sectors which have major economic potential and capable of
generating economic growth, more employment and increased foreign earnings.
Our strategy is to create synergies among players operating in the above sectors, namely,
Governments, Utilities, Industries and Clusters, Academic and Research Institutions, Investors and
Entrepreneurs, Commercial and Investment banks, Multilateral and Bilateral financial institutions to
accelerate the roll out of viable commercial and industrial projects, integrating green and smart
technologies across Africa. You may please visit our website (www.afrief.com) for more information
about the Initiative.
We believe in developing mutually beneficial relationships. Accordingly, we would be glad if you will
kindly grant audience to Dr Cemal Kaldirimci to discuss with you about the possibility of establishing
a collaboration between AFRIEF and your company for the purpose of implementing projects,
sharing knowledge and best practices under the Initiative in Africa. We believe that your expertise
and years of experience in the sectors will bring considerable benefit to the Initiative and the people
of Africa.
While looking forward to hearing from you soon, may you please accept our warmest regards and
best wishes.
Sincerely Yours
Baba Yunus Muhammad
President

our portfolio

Transcription

Similar documents

2012 MetanVB Boston Whaler 16`7” Sakonnet

EZ Green, cat# 873

(MSDS) Organic Coconut Oil

Recycling Bloopers

(MSDS) Kukui Nut Oil RBDW

Master Recycler Program Self Haul Disposal Rates

Chemical Waste Management, Inc. Kettleman Hills

tempilstik 200f (93c) - Independent Wholesale Welding Supply

January 2015

Recycling Guide - Waste Management