mitsubishi 1997-up montero sport

RADIO
EQ
STACK
TUNERS / CASSETTE / DISC PLAYERS
MINI
STAN
DIN
ISO DIN
SINGLE
DBL DIN
CHASSIS H
13/4-2
2
2
2
37/8
3
CHASSIS W
1
7 /8
1
7 /8
1
7 /8
7
71/8
71/8
CHASSIS D
43/4-51/2
57/8-611/16
57/8-611/16
57/8-611/16
57/8-611/16
57/8-611/16
NOSE H
15/8-13/4
15/8-13/4
23/8
113/16
33/4-4
NOSE W
41/8-43/16
41/8-43/16
71/2
611/16
611/16-71/4
SHAFT SP.
1
3
UPDATED
THROUGH
'98
'99
2000
2001
MITSUBISHI
1997-UP
MONTERO SPORT
4 Door Sport Utility
1
5 /8-5 /4
5 /8-6
IN DASH APPLICATION NOTES
KS
KS
APPLICATION KIT MODEL:
HARNESS ADAPTOR:
F1
PK4
N
N
DIN1190 (FOR SHAFT RADIO)
MI02
MDA-1
ANTENNA ADAPTOR:
IN-DASH INSTALLATION AREA DIMENSIONS
MAX
DEPTH
DEPTH
CAVITY
7"
DASH
OPENING
DASH MATERIAL:
WIDTH
7"
10"
3"
1
7 /8"
TYPE: ISO DIN
PLASTIC
HEIGHT
THICKNESS:
2"
3
/16"
REMOVE REAR SUPPORT
MODIFY CAVITY
FOR MAX DEPTH
AMPLIFIER/EQ MOUNTING LOCATIONS
UNDER/IN
DASH
UNDER
SEAT
(WxHxD)
GLOVE
BOX
TRUNK/
CARGO
11 x 5 x 7"
Various
Dimensions shown are inches.
For inch/mm conversions refer to chart section.
NOTE: THIS MANUAL IS BASED ON CAREFULLY DOCUMENTED RESEARCH. ABSOLUTE
ACCURACY IS ATTEMPTED BUT NOT GUARANTEED. USE THIS MANUAL AS A REFERENCE
GUIDE. SCOSCHE, INC. CANNOT BE RESPONSIBLE FOR INCONSISTENCIES THAT MAY OCCUR.
•
•
OEM Infiniti amp, if equipped is located behind right rear quarter panel.
OEM CD changer, if equipped is located in left rear side storage
compartment.
DASH.
B
C1
C2
D
D1
D2
D3
F1
F2
K
K1
K2
K3
K4
=
=
=
=
=
=
=
=
=
=
=
=
=
=
BACK UP PLATES REQUIRED.
CUT TRIM/PLASTIC (STRUCTURE).
CUT STEEL.
BELOW DECK ONLY.
LIFT PORTION OF DECK. (MAY REQUIRE STRUCTURAL REINFORCEMENT).
CUT STEEL WHEN TOP MOUNTED. DO NOT IF BELOW DECK.
NARROW SURFACE, BELOW DECK ONLY.
MINIMUM MODIFICATION FILE SHAFT HOLES OR DASH OPENING.
MODIFY DASH CAVITY AND/OR PANEL.
INSTALLATION KIT, SPACER OR ADAPTOR REQUIRED.
KIT MODIFICATIONS REQUIRED.
EXTENSION KIT RECOMMENDED.
WHEN EQUIPPED WITH FACTORY "ELECTRONIC" RADIO.
FABRICATE PANEL/BRACKETS.
173
K5 = WHEN EQUIPPED WITH STANDARD TWO SHAFT RADIO/TAPE PLAYER. FABRICATE
KIT WHEN EQUIPPED WITH FLAT FACE ELECTRONIC RADIO/TAPE PLAYER.
K S = SCOSCHE KIT RECOMMENDED.
N = NOT RECOMMENDED. EXTENSIVE MODIFICATION REQUIRED.
P = PERFECT WITHOUT MODIFICATION.
P1 = MODIFY OR REMOVE POCKETS.
P2 = COIN POCKET LOCATION IN DASH (MAY REQUIRE TRIM KIT).
P3 = PERFECT WHEN EQUIPPED WITH STANDARD TWO SHAFT RADIO, K WITHOUT.
R = REAR LOAD ISOMOUNT.
U = UNDERDASH.
W1 = WITH POWER WINDOWS ONLY.
W2 = WITHOUT POWER WINDOWS ONLY.
©
1997-UP MITSUBISHI MONTERO SPORT
4 DOOR SPORT UTILITY
3" MIDRANGE LOCATED IN THE DASH.
FRONT DOOR PANEL.
PRELIMINARY:
DISCONNECT THE NEGATIVE BATTERY CABLE
ANTENNA:
THE FACTORY POWER/ROD ANTENNA IS LOCATED ON THE
TOP OF THE RIGHT FRONT FENDER. ON DELUXE TRIM VERSIONS
THERE IS A DIVERSITY ANTENNA LOCATED IN THE FAR REAR LEFT
QUARTER WINDOW GLASS.
RADIO REMOVAL AND IN-DASH INSTALLATION:
NOTE: THE FACTORY RADIO PROVISION IS FOR A DIN STYLE RADIO.
MINOR DASH FILING IS REQUIRED FOR AFTERMARKET DIN STYLE UNITS
OR NO MODIFICATIONS IF THE AFTERMARKET RADIO HAS ISO SIDE
MOUNTING PROVISIONS.
1. OPEN GLOVE BOX AND REMOVE (1) SCREW AT UPPER LEFT IN DASH
TRIM.
2. REMOVE (1) PUSH-PIN TYPE FASTENER FROM BLACK UNDERDASH
COVER, TO ACCESS (1) SCREW BELOW GLOVEBOX, AND REMOVE IT.
3. EXTRACT (4) SCREWS FROM LOWER EDGE OF DRIVER’S LOWER DASH
PANEL, POP OUT (2) CAPS AND EXTRACT THE SCREWS FROM UPPER
AREA OF PANEL. REMOVE DRIVER’S SIDE LOWER DASH PANEL. IT IS
NOT NECESSARY TO DISCONNECT HOOD RELEASE CABLE.
4. EXTRACT (2) SCREWS FROM LEFT SIDE OF RADIO PANEL.
5. EXTRACT (2) SCREWS FROM INSTRUMENT/GAUGE BEZEL, AND UNSNAP
RIGHT SIDE OF PANEL NEAR HEAT/AC CONTROLS.
6. EXTRACT (2) SCREWS FROM ASH TRAY HEAT SHIELD, RELEASE LIGHT
BULB, AND REMOVE.
7. LIFT UP AND HOLD UPPER DASH PANEL OUT OF WAY AND CAREFULLY
PULL OUT RADIO/CUP HOLDER BEZEL. UNPLUG LIGHTER AND REMOVE
RADIO BEZEL.
8. EXTRACT (4) SCREWS SECURING THE RADIO, UNPLUG ALL
CONNECTORS, AND REMOVE.
DOOR PANEL MOUNTED 1" TWEETER (INFINITI SYSTEM)
FRONT DASH SPEAKER INSTALLATION:
NOTE: THE FACTORY SPEAKER PROVISION IS FOR A 4" 2-HOLE FOOTBALL
STYLE SPEAKER. ON DELUXE TRIM/INFINITY AUDIO THERE IS A 3"
MIDRANGE MOUNTED TO A 4" 2-HOLE ADAPTER PLATE
DRIVER’S (LEFT) SIDE:
1. EXTRACT (4) SCREWS FROM LOWER EDGE OF DRIVER’S LOWER DASH
PANEL, POP OUT (2) CAPS AND EXTRACT THE SCREWS FROM UPPER
AREA OF PANEL. REMOVE DRIVER’S SIDE LOWER DASH PANEL. IT IS
NOT NECESSARY TO DISCONNECT HOOD RELEASE CABLE.
2. EXTRACT THE (2) SCREWS SECURING THE SPEAKER, UNPLUG THE
SPEAKER LEADS AND REMOVE THE SPEAKER.
PASSENGER’S (RIGHT) SIDE:
1. OPEN GLOVEBOX AND EXTRACT (1) SCREW FROM UPPER LEFT GRILLE
PANEL.
2. EXTRACT (2) SCREWS FROM BOTTOM OF GRILLE PANEL AND REMOVE IT.
3. EXTRACT THE (2) SCREWS SECURING THE SPEAKER, UNPLUG THE
SPEAKER LEADS AND REMOVE THE SPEAKER.
7" DOOR SPEAKER IN A FACTORY ADAPTER.
174
©
1997 SCOSCHE INDUSTRIES, INC.
1997-UP MITSUBISHI MONTERO SPORT
4 DOOR SPORT UTILITY
FACTORY DASH POCKET.
FACTORY DASH BEZEL.
FRONT DOOR SPEAKER INSTALLATION:
NOTE: THE FACTORY SPEAKER PROVISION IS FOR A 7" 4-HOLE PIN
CUSHION STYLE SPEAKER IN A FACTORY ADAPTER. AN ADAPTER IS
RECOMMENDED WHEN INSTALLING AFTERMARKET 51/4" AND 61/2"
SPEAKERS. WE RECOMMEND THE SCOSCHE SAC656 SPEAKER
ADAPTERS.
NOTE: ON INFINITY/DELUXE TRIM LEVELS THERE IS A 1" TWEETER
MOUNTED TO THE FRONT UPPER DOOR PANEL ITSELF.
1. EXTRACT (2) SCREWS FROM THE FRONT EDGE OF DOOR PANEL.
2. EXTRACT (1) SCREW FROM ARMREST POCKET.
3. EXTRACT (1) SCREW W/COVER CAP FROM THE TOP BACK EDGE OF
DOOR PANEL.
4. EXTRACT (1) SCREW FROM THE LOWER BACK EDGE OF DOOR PANEL.
5. POP OUT INSIDE TRIANGLE MIRROR COVER PIECE.
6. POP UP POWER WINDOW SWITCH FROM THE BACK EDGE FIRST,
UNPLUG AND REMOVE THE PANEL.
7. EXTRACT (1) SCREW FROM BACK OF DOOR RELEASE/LOCK TRIM CUP
AND REMOVE CUP.
8. USING A PANEL REMOVAL TOOL CAREFULLY PRY OUT ON THE BOTTOM
AND SIDE OF THE DOOR PANEL TO RELEASE THE FASTENERS AND
REMOVE THE PANEL.
9. EXTRACT THE (4) SCREWS SECURING THE SPEAKER TO THE ADAPTER,
PULL THE SPEAKER OUT OF THE DOOR, UNPLUG THE SPEAKER LEADS
AND REMOVE THE SPEAKER.
AFTERMARKET 61/2" SPEAKER INSTALLATION WITH AN “SAC656” ADAPTER.
TWEETER REMOVAL:
1. WITH DOOR PANEL REMOVED, EXTRACT (1) NUT FROM BACK OF
TWEETER TO REMOVE.
REAR DOOR SPEAKER INSTALLATION:
NOTE: THE FACTORY SPEAKER PROVISION IS FOR A 7" 4-HOLE PIN
CUSHION STYLE SPEAKER IN A FACTORY ADAPTER. AN ADAPTER IS
RECOMMENDED WHEN INSTALLING AFTERMARKET 51/4" AND 61/2"
SPEAKERS. WE RECOMMEND THE SCOSCHE SAC656 SPEAKER
ADAPTERS.
1. EXTRACT (1) SCREW FROM BACK OF DOOR RELEASE/LOCK TRIM CUP
AND REMOVE CUP.
2. EXTRACT (1) SCREW FROM ARMREST POCKET.
3. EXTRACT (2) SCREWS W/COVER CAPS FROM THE BACK EDGE OF DOOR
PANEL.
4. USING A PANEL REMOVAL TOOL CAREFULLY PRY OUT ON THE BOTTOM
AND SIDE OF THE DOOR PANEL TO RELEASE THE FASTENERS AND
REMOVE THE PANEL.
5. EXTRACT THE (4) SCREWS SECURING EACH SPEAKER TO THE
ADAPTER, UNPLUG THE SPEAKER LEADS, AND REMOVE THE SPEAKER.
FACTORY INFINITY AMP REMOVAL:
NOTE: ON INFINITY AUDIO SYSTEMS/DELUXE TRIM LEVELS THE FACTORY
AMPLIFIER IS LOCATED BEHIND THE LEFT REAR CARGO SIDE PANEL.
1. FOLD SEATS FORWARD, REMOVE FASTENERS AND POP OUT REAR SIDE
PANEL TO ACCESS AMPLIFIER.
175
REAR OF OEM RADIO WITH, 13 PIN CD CHANGER INPUT,
6 PIN AUDIO OUTPUT, AND DIVERSITY ANTENNA INPUT.
©
1997 SCOSCHE INDUSTRIES, INC.