GSI_Secuguard_Basic5.. - Golden State Instrument Co.

GOLDEN STATE INSTRUMENT CO.
GSI SecuGuard
Basic 5.0
User manual
3002 DOW AVE STE 228
TUSTIN, CA 92780
Phone (888)808-0909
Email [email protected]
SecuGuard Basic
System Requirement ............................................................................................. 5
Installation ............................................................................................................. 6
Before Installing the Software ............................................................................................. 6
Starting the Installation ........................................................................................................ 6
Quick Start ........................................................................................................... 10
Install IP Camera(s) ........................................................................................................... 10
Add IP Camera(s)............................................................................................................... 10
Configuration of schedule recording: ............................................................................................................ 14
Playback: ....................................................................................................................................................... 20
1. Main-console .................................................................................................... 24
1.1 System status:............................................................................................................... 25
1.3 DI/O status : ................................................................................................................. 27
1.4 Operation with sub-screen: .......................................................................................... 28
1.4.1 Define display camera(s) sequence : .................................................................................................... 28
1.4.2 Digital Zoom at sub-screen : ................................................................................................................ 29
1.4.3 Switch to Full screen : .......................................................................................................................... 29
1.4.4 Snapshot of sub-screen : ....................................................................................................................... 29
1.4.5 Restore quad default : ........................................................................................................................... 30
Reset division setting to default..................................................................................................................... 30
1.5 System setup: ............................................................................................................... 31
1.5.1 System page at System setup dialog : ................................................................................................... 31
1.5.1.1 Start up config : ..................................................................................................................... 32
1.5.1.2 Language config : .................................................................................................................... 32
1.5.1.3 Auto scan :............................................................................................................................... 32
1.5.1.4 Storage config : ....................................................................................................................... 33
1.5.1.5 System status :
1.5.1.6 HDD status :
............................................................................................................... 34
.................................................................................................................. 34
1.5.1.7 NxN Divison:........................................................................................................................... 34
1.5.2 Camera page at System setup dialog : .................................................................................................. 35
1.5.2.1 Camera list : ............................................................................................................................ 35
1.5.2.2 OSD Config : ........................................................................................................................... 36
1.5.2.3 Camera Config : ...................................................................................................................... 36
1.5.2.4 Search Page : ........................................................................................................................... 38
1.5.2.5 Channel parameter Page: ......................................................................................................... 39
1.5.3 User page at System setup dialog : ....................................................................................................... 41
1.5.3.1 User Privilege : ........................................................................................................................ 42
1.5.3.2 Account list: ............................................................................................................................ 43
1
SecuGuard Basic
1.5.3.3 User config: ............................................................................................................................. 44
1.5.4 Address Book page at System setup dialog : ........................................................................................ 45
1.5.4 Mail page at System setup dialog : ....................................................................................................... 46
1.5.4.1 SMTP Setting: ......................................................................................................................... 46
1.5.4.2 Mail Content: ........................................................................................................................... 47
1.5.4.3 Alarm Setting: ......................................................................................................................... 47
1.6 Schedule setup: ............................................................................................................ 48
1.6.1 Schedule mode : ................................................................................................................................... 49
1.6.2 Select camera of Daily mode :.............................................................................................................. 49
1.6.3 Select weekday of Weekly mode :........................................................................................................ 50
1.6.4 Select camera of special day mode :..................................................................................................... 50
1.6.5 Add and remove special day:................................................................................................................ 51
1.6.6 Add schedule time slice :...................................................................................................................... 51
1.6.7 Modify schedule time period: ............................................................................................................... 52
1.6.8 Remove schedule time slice : ............................................................................................................... 52
1.6.9 Record Setup Page : ............................................................................................................................. 53
1.6.10 Record Mode : .................................................................................................................................... 53
1.6.11 Record Setting : .................................................................................................................................. 54
1.6.12 Motion Config : .................................................................................................................................. 54
1.6.13 DI Record Setting : ........................................................................................................................... 55
When you set the DI Record mode , Select the DI input from the combo box , and select the DI is open or
close to trigger recording. .............................................................................................................................. 55
1.6.14 Complete Schedule Setting :............................................................................................................... 55
1.7 Start & Stop Monitor: .................................................................................................. 56
1.8 E-Map: ......................................................................................................................... 57
1.8.1 Camera list: .......................................................................................................................................... 58
1.8.2 Add camera to Map: ............................................................................................................................. 58
1.8.3 Make camera to focus camera: ............................................................................................................. 58
1.8.4 Move camera on Map: .......................................................................................................................... 58
1.8.5 Rotate camera on Map:......................................................................................................................... 58
1.8.6 Delete camera on Map:......................................................................................................................... 59
1.8.6 Change Map: ........................................................................................................................................ 59
1.9 Two way Audio : .......................................................................................................... 59
1.10 PTZ control : .............................................................................................................. 60
1.10.1 Speed control: ..................................................................................................................................... 60
1.10.2 Direction control:................................................................................................................................ 61
1.10.3 Tour control: ....................................................................................................................................... 62
1.10.4 Preset control: ..................................................................................................................................... 62
2
SecuGuard Basic
1.10.5 Auto pan control: ................................................................................................................................ 62
1.10.6 Zoom control: ..................................................................................................................................... 62
1.10.7 Focus control: ..................................................................................................................................... 62
1.10.8 IRIS control: ....................................................................................................................................... 62
2. Playback ........................................................................................................... 63
2.1 Search history record file(s) : ....................................................................................... 64
2.1.1 Search history file(s) dialog :................................................................................................................ 64
2.1.2 Select a day to search history file(s): .................................................................................................... 65
2.1.3 Select record mode(s): .......................................................................................................................... 65
2.1.4 Start search: .......................................................................................................................................... 65
2.1.5 Review history record file(s) in search period: ..................................................................................... 65
2.1.6 Assign time period of search result: ..................................................................................................... 66
2.1.7 Select the camera(s) to playback: ......................................................................................................... 66
2.1.8 Start playback history file(s):................................................................................................................ 66
2.2 Playback control button(s): .......................................................................................... 67
2.2.1 Play button:
.................................................................................................................................. 67
2.2.2 Pause button:
................................................................................................................................ 67
2.2.3 Reverse play button:
2.2.4 Stop button:
..................................................................................................................... 67
.................................................................................................................................. 67
2.2.5 Next frame button:
....................................................................................................................... 67
2.2.6 Previous frame button:
................................................................................................................. 67
2.2.7 Playback speed control:
................................................................................................................ 68
2.2.8 Division control buttons: ...................................................................................................................... 68
2.3 Convert to AVI file: ...................................................................................................... 69
2.3.1 Convert file dialog: ............................................................................................................................... 69
2.3.2 Select a day to covert history file(s): .................................................................................................... 70
2.3.3 Assign time period to prepare convert job:........................................................................................... 70
2.3.4 Select a camera to prepare convert job: ................................................................................................ 70
2.3.5 Select a folder to place converted file: ................................................................................................. 70
2.3.6 Start converting job: ............................................................................................................................. 70
2.4 Switch audio play mode: .............................................................................................. 71
2.5 Playback setting: .......................................................................................................... 71
2.6 Snapshot dialog: ........................................................................................................... 71
2.6.1 Snapshot all dialog: .............................................................................................................................. 72
2.6.2 Select snapshot image:.......................................................................................................................... 72
2.6.3 Select output folder: ............................................................................................................................. 73
2.6.4 Select output file format: ...................................................................................................................... 73
2.6.5 Save snapshot images: .......................................................................................................................... 73
3
SecuGuard Basic
2.6.6 Saved image file name: ........................................................................................................................ 73
2.7 Backup history file(s):.................................................................................................. 74
2.7.1 Backup dialog:...................................................................................................................................... 74
2.7.2 Select backup date and time period: ..................................................................................................... 74
2.7.3 Select backup camera(s) and backup time period: ................................................................................ 74
2.7.4 Select output directory:......................................................................................................................... 74
2.7.5 Start backup job:................................................................................................................................... 74
2.7.6 Playback backup files: .......................................................................................................................... 75
2.8 Playback status: ............................................................................................................ 75
2.9 Operation with sub-screen: .......................................................................................... 76
2.9.1 Define display camera(s) sequence : .................................................................................................... 76
2.9.2 Digital Zoom at sub-screen : ................................................................................................................ 77
2.9.3 Switch to Full screen : .......................................................................................................................... 77
2.9.4 Snapshot of sub-screen : ....................................................................................................................... 77
2.9.5 Smart Search: ............................................................................................................................. 79
3. Repair database ............................................................................................... 81
3.1 Repair database status: ................................................................................................. 82
4. Un-install .......................................................................................................... 83
4
SecuGuard Basic
System Requirement
FPS
~120
120~360
360~540
540~960
960~
(QVGA)
CPU
RAM
Intel P4
Intel P4
2.4GHz
3.2GHz
512MB
512MB
Display
Intel
Intel core 2 Intel core 2 Quad
Pentium D Duo E8600 Q9650
950
3.3GHZ
3.0GHZ
3.4GHZ
1GB
2GB
2GB
support1024x768 resolution or above
Support DirectX 9.0c or above
Intel 945G or Intel 965G or above
Windows 2000 , XP , Vista , Windows 7
OS
Hard disk
60GB
Ethernet
100Mbps
Chipset
1Gbps
Intel 945 or Intel 965 or above
＊ If you install the SecuGuard with the Vista , we recommend you that should be install
more physical memory at system.
QVGA = 320 x 240 pixel
CIF = QVGA , D1 = VGA at mapping table below.
Image resolution mapping table
Resolution
Compared with QVGA
QQVGA
QQVGA = QVGA / 4
VGA
VGA = QVGA x 4
SXGA
SXGA = QVGA x 16
5
SecuGuard Basic
Installation
Installation
Before Installing the Software
1.Make sure your PC has DirectX 9.0c or above installed.
2.Use the the enclosed software CD.
3.Run Setup.exe, which is included on the SecuGuard series Software
CD.
Starting the Installation
Step 1.
The Installation Wizard will start. Select the language that you
want to use between installation.
6
SecuGuard Basic
Installation
Step 2.
The License Agreement window will open next.
Click “I Agree” to continue.
7
SecuGuard Basic
Installation
Step 3.
Select the “SecuGuard Basic” , then click Next button.
Step 4.
The Choose Destination Location window will open next.
Select the folder you wish to intall SecuGuard Basic to, and then click
on Next to continue.
8
SecuGuard Basic
Installation
Step 5.
The Installation Wizard Complete window will open next.
Click on Close to complete the installation.
9
SecuGuard Basic
Quick Start
Quick Start
Install IP Camera(s)
Step 1 ： Setup the IP camera(s) following by the instruction manual provided
by the manufacturer.
Step 2 ： Check the network between the IP camera(s) and the system.
Step 3 ： Add the IP camera(s) to the system following below steps.
Add IP Camera(s)
Step 1 ： Click the Start → All Programs → SecuGuard → Mainconsole.
Step 2 ： Key-in User name and password to login SecuGuard
(default User name is “admin” without password)
Checked the “Remember User” for next time login system will auto fill the User field
by login account this time.
10
SecuGuard Basic
Quick Start
Step 3 ： Click System setup
Step 4 ： Select Camera page and key-in camera’s information , then click
“Add” button.
11
SecuGuard Basic
Quick Start
Camera information:
Please confirm the “Vendor” and “Model”
setting is the same with camera , or may cause
the camera not functional.
If you need change the Camera Parameters, click
button.
Select the Codec and resolution , connect protocol and streaming port for current
connection .
Checked the “Enable Audio” if you need to receive Audio streaming data .
If you need record audio with record file, you must checked “Enable Audio” and
“Enable Audio Record” both.
12
SecuGuard Basic
Quick Start
Step 5 ： Click the “Search” button for search the camera(s) were installed in
local LAN, wait for search complete then select the cameras that you
need, and click “OK” button for finish add camera job.
Step 6 ： Confirm all inserted camera’s setting parameter.
Step 7 ： Click “OK” button.
Step 8 ： Now you can preview live stream at main page.
13
SecuGuard Basic
Quick Start
Configuration of schedule recording:
Step 1 ：
Click “Schedule Setup” button.
Step 2 ： Select the Schedule type that you need.
Daily mode :
Weekly mode:
Special day mode:
Setup each camera’s recording time and type at every day .
Setup each camera’s recording time and type at each weekday.
Setup each camera’ recording time and type at assigned day.
14
SecuGuard Basic
Quick Start
If the Special day schedule was set , when the time commit the special day
setting, system will execute this special day setting immediately , even system has
the same time period setting of daily or weekly schedule setup.
Step 3 ： Select one camera for schedule configuration.
Step 4 ： Select one of weekday for setup schedule(weekly mode)
15
SecuGuard Basic
Quick Start
Step 5 ： If you want to modify an exist schedule period , Select the period first
from time period list or time period bar, or skip this step.
Step 6 ： Modify the time period from time-select control or drag the period bar
below.
Step 7 ： After setting with time period , If you want to Add a new period , click
“Add” button , or you want to modify exist period was selected , click
the “Edit” button .
16
SecuGuard Basic
Quick Start
Step 8 ： Choose the Round-the-clock or Motion detection or DI detection record
mode.
Step 9 ： If you select the Motion detection mode , you have to set the detection
area , or use default setting.
17
SecuGuard Basic
Quick Start
Add detection area:
Click “Add” button , then drag a rectangle on the preview image.
Remove detection area:
Click “Delete” button , then drag a rectangle on the preview image.
Recover to default area:
Click the “Default” button.
The red transparent area is detection area , otherwise will not be detected.
Step 10 ： DI Record Mode:
1. Select trigger recording from which DI input.
2. Set trigger recording depend on DI is open or close.
18
SecuGuard Basic
Quick Start
Step 11 ： Start schedule monitor.
Click the Monitor button and checked the Start Monitor all or Start
Monitor Schedule.
19
SecuGuard Basic
Playback
Playback:
Step 1 ： Click Playback button to approach playback panel.
Step 2 ： Click Search button to approach search dialog.
20
SecuGuard Basic
Playback
Step 3 ： Click on the date that you want to search record file.
Step 4 ： Choose Record mode(s) that you need(Round the clock ,
Motion , Alarm)
Step 5 ： Click Search button.
21
SecuGuard Basic
Playback
Step 6 ： System will displayed record file(s) status in list control below.
Blue:
Round the clock record file.
Green: Motion detection record file.
Red:
DI triggered record file.
Step 7 ： Drag mouse cursor on the list control to select playback time
period.
Step 8 ： Select the camera(s) to playback.
System allowed maximum 16 cameras playback at once.
22
SecuGuard Basic
Playback
Step 9 ： Click OK button to finish search record file for playback job.
Step 10 ： Click play button to start playback procedure.
23
SecuGuard Basic
1. Main-console
1. Main-console
This is the main control panel of system , to provide live stream preview , system
setup , E-Map, schedule setup , playback , start or stop monitor , and PTZ controls.
System
information
DI/O status
Function
buttons
Display
preview
Divide
buttons
Rolling &
Fullscreen
24
PTZ
buttons
SecuGuard Basic
1. Main-console
1.1 System status:
System
status
Exit
Exit:
Exit:
1.
2.
3.
4.
Logout: Logout current User
Minimize: Minimize the Main-console to taskbar
Exit: Shutdown SecuGuard
Version: Display version number.
System status:
1.
2.
3.
4.
5.
System Date
System Time
Weekly day
Monitor status, if monitor stop , it will show
nothing
Hard disk available free size
These system status can configuration at system setting , please reference to “Setup
page”.
Hard Disk available free size has three color type , they means:
1. Green : normal
2. Yellow: recycle job executing
3. Red:
System can’t found available free size.
25
SecuGuard Basic
1. Main-console
1.2 Screen Division :
Assign the preview screen to expected layout division by clicking these buttons.
To switch to single camera display, double click on a particular sub-screen.
Double click on the screen again to regain previous screen division layout.
Divide to 1 Screen
Divide to 4 Screen(s)
Divide to 6 Screen(s)
Divide to 9 Screen(s)
Divide to 16 Screen(s)
Divide to 32 Screen(s)
Divide to 64 Screen(s)
Divide to NxN Screen(s)
Switch to Full screen mode
Start Rotate sub-screen(s)
Stop Rotate sub-screen(s)
26
SecuGuard Basic
1. Main-console
1.3 DI/O status :
Display real-time status of focus camera’s DI/O, and switch DO status by click DO
button.
Amount of DI/O button(s) depend on focus camera , it’s changed with focus camera
was changed.
System was default set to NC status(normal close) , so if DI status became to
open , the icon will show as red light.
DI is opening
DI is closed
When DO showed as
If DO showed as
, it means the DO is opening .
, it means the DO is closed.
You can click on the DO icon to change DO status. If after you click the DO
icon , but the status doesn’t changed, it means set new DO status to camera fail ,
please check network status or camera status.
27
SecuGuard Basic
1. Main-console
1.4 Operation with sub-screen:
1.4.1 Define display camera(s) sequence :
1.
To switch display sequence in sub-screen(s) , press and hold mouse left
button on source sub-screen , than drag to target sub-screen and release
mouse left button.
2.
To switch current sub-window to another camera , click mouse right
button on the sub-screen , than choose the live camera you needed.
3.
To remove camera display, click the mouse right button and click
Remove Camera display on popup menu.
28
SecuGuard Basic
1. Main-console
1.4.2 Digital Zoom at sub-screen :
1. Click mouse right button on sub-screen , and checked Digital Zoom.
2. Move mouse cursor to the position that you wanted to digital zoom-in.
3. Move mouse wheel forward until the image satisfied that you needed.
4. Move mouse wheel backward to digital zoom-out.
5. Press and hold mouse left button to drag the image at sub-screen to the
position that you needed.
6. To cancel digital zoom mode , click mouse right button and un-checked
Digital Zoom.
1.4.3 Switch to Full screen :
1. Click mouse right button and checked Full screen on popup menu to
switch to Full screen.
2. Click mouse right button and un-checked Full screen on popup menu to
switch to Full screen.
3. Click “Esc” button or un-checked “Full screen” on popup menu to return
normal display mode.
1.4.4 Snapshot of sub-screen :
1. Click mouse right button and choose Snapshot on popup menu .
2. Configuration with the image by Snapshot dialog.
3. Click Save button and choose the folder that you wanted to save to.
29
SecuGuard Basic
1. Main-console
Snapshot dialog:
Bright :
100 = Maximum brightness, -100 = Maximum dark
Contrast:
100 = Maximum strong with Contrast, -100 = Minimum value of Contrast.
Grayscale:
Click to switch image to grayscale mode.
Sharp:
Click Sharp button to increase image sharp level.
Soft:
Click Soft button to increase image soft level.
Reset:
Click Reset button to recover image to original image.
Print:
Click Print button to print out image to printer.
Save:
Click Save button to choose folder and file name to save.
Close:
Close Snapshot dialog.
1.4.5 Restore quad default :
Reset division setting to default.
30
SecuGuard Basic
1. Main-console
1.5 System setup:
Click system setup button to approach System setup dialog.
1.5.1 System page at System setup dialog :
31
SecuGuard Basic
1. Main-console
1.5.1.1 Start up config :
Auto Start :
Auto start Main-console when system
boot-up.
Auto moinitor all:
Auto started monitor all when
Main-console boot-up
Auto Full Screen:
Auto switch Full screen when Main-console boot-up.
Minimized at started:
Auto Minimized Main-console window when system boot-up.
Auto login:
Auto login when system boot-up , must set with “Auto login” config.
1.5.1.2 Language config :
Click on the combo box of language ,
and select the language that you needed ,
system will change language immediately.
1.5.1.3 Auto scan :
Set the screen rotation interval by seconds.
32
SecuGuard Basic
1. Main-console
1.5.1.4 Storage config :
3.
Click Add button to select a new record folder for recording work.
4.
Click Delete button to remove selected record folder from list.
5.
Click Move up and Move down button to change sequence of recording
priority, Top of list is the first priority of recording work.
6.
Set Keep space with MB , it means when the hard disk free space less than
setting number , system will begin recycle work to kill oldest record file.
7. Must click “Edit” button after modified “Keep space over” value.
33
SecuGuard Basic
1. Main-console
1.5.1.5 System status :
Select status item(s) for display at system status
window.
Checked means this status will displayed at
main-console status window, otherwise will display
nothing.
If “Hide when minimized” was checked , when
set main-console minimized , the icon will move to
system tray at left-down corner.
Click the icon at system tray for restore main-console.
1.5.1.6 HDD status :
The Main-console will display hard disk(s) free
space by choose “Show available size”. And display
percentage of free space in hard disk(s) by selected
“Show available percentage”.
1.5.1.7 NxN Divison:
Set the N of NxN division. When user click NxN
division button , Main-console will divided the
sub-screen(s) by this value .
If this value is set to 1, the divided sub-screen(s) is one sub-screen,
If this value is set to 2, the divided sub-screen(s) is four sub-screen,
If this value is set to 3, the divided sub-screen(s) is nine sub-screens,
And so on…
34
SecuGuard Basic
1. Main-console
1.5.2 Camera page at System setup dialog :
1.5.2.1 Camera list :
List all camera(s) installed at system, Displayed
by camera index and camera name.
Checked each camera for enable them , if you
need to disable some camera(s) , please un-checked it
from the check box before camera name.
35
SecuGuard Basic
1. Main-console
1.5.2.2 OSD Config :
System could show several information on the
sub-screen .
Checked the check box before the information to
enable displayed this information.
The information displayed on the preview screen at
left-upper corner immediately .
Show Date:
Display system date.
Show Time:
Display system time.
Show Camera Name:
Display this Camera name.
Show Frame per second:
Display the number of frame per second at this channel.
Show Bitrate:
Display the number of bit-rate per second at this channel.
1.5.2.3 Camera Config :
Vendor:
Select current Vender of this camera , If the selected Vender doesn’t identical to the
camera , this channel may not working correctly .
36
SecuGuard Basic
1. Main-console
Model:
Select current Model name of this camera , If the selected Model doesn’t identical to
the camera , this channel may not work correctly.
Camera name:
Set this channel’s camera name for identify this camera in system.
IP:
Set this camera’s IP.
Port:
Set this camera’s HTTP port.
User:
Set the User name for this camera, The User name must have the authority to login
this camera .
Password:
System use the User name and password to login this camera.
Add button:
Insert camera configuration to system.
Delete button:
Remove camera configuration from system.
Edit button:
Modify the configuration from system.
Must click “Edit” button after modified camera’s configuration , or the system
will not saved modify configuration.
37
SecuGuard Basic
1. Main-console
Search button:
Click the Search button for search the cameras at local LAN , System will popup a
dialog and display all found cameras in the list .
Wait for search completed and checked the cameras that you need.
1.5.2.4 Search Page :
Select all button:
Auto checked all cameras that system found.
Cancel all button:
Auto un-checked all cameras that system found.
OK button:
Confirm all selected camera and return previous page.
Cancel button:
Cancel all action at this page , and return previous page.
Config detail button:
Click “Config detail” button to open web page for
configuration with the camera.
Camera parameter button:
Click “Camera parameter” button to open setup
camera more parameter page.
38
SecuGuard Basic
1. Main-console
1.5.2.5 Channel parameter Page:
Video Config:
Video codec:
Select the video codec that system will receive from camera.
Resolution:
Select the Resolution that system will receive from camera.
PS. The codec and resolution capability is depend on camera.
Network Config:
Protocol:
Select which protocol for system that uses to connect to camera.
RTSP Port:
Set RTSP port number for connect to camera.
39
SecuGuard Basic
1. Main-console
Audio Config:
Enable Audio:
Set Audio enabled for receive audio streaming , If you need listen to live audio ,
This value must be enabled.
Enable Audio Record:
Enable this value for record audio data in recording file.
PS. The Audio Record must Enabled with “Enable Audio” value both.
OK button:
Save the connecting configuration , and return previous page.
Cancel button:
Cancel all configuration at this page , and return previous page.
40
SecuGuard Basic
1. Main-console
1.5.3 User page at System setup dialog :
41
SecuGuard Basic
1. Main-console
1.5.3.1 User Privilege :
User Privilege tree control is defined user’s
privilege of each function of system , checked status
means user can use this function , un-checked
means user can’t use this function.
Main console:
Main function of system , user must have this
privilege or user will couldn’t do anything with
system.
Start and Stop Monitor:
This function is means user can start or stop
system monitor work (schedule recording).
Schedule Setup:
The privilege of user can entry schedule setup
page.
System Setup:
The privilege of user can entry system setup
page.
EMap:
The privilege of user can execute E-Map function.
Preview Quad control:
The privilege of user can change divide of sub-screen.
PTZ control:
The privilege of user can control Pan, Tilt , Zoom function of camera.
Playback:
The privilege of user can playback history recorded file.
Two way Audio:
The privilege of user can enable talk with camera.
Preview:
The privilege of user can preview live streaming.
Selected the camera(s) for this user can preview which live streaming.
42
SecuGuard Basic
1. Main-console
1.5.3.2 Account list:
Display all user’s information of system.
If you want to modify user’s configuration or delete user , please click on the user
name at list first.
When you modified user’s information (add, edit or delete), please confirm the data
that you modified data is appeared at list.
“admin” account:
System administrator .
“logout” account:
When system in logout status , System will set privilege by the “logout” setting.
43
SecuGuard Basic
1. Main-console
1.5.3.3 User config:
Configuration of user’s information.
User :
User name.
Group:
Select the group of user. The admin group default has all privilege of system , the
user group default only has Main-console privilege.
Password:
The password of user for login system.
Confirm password:
Retype the password.
Description:
The description information of user.
Disable User:
Checked this check box for disable the user was selected,.
Add button:
Key-in user’s information and checked user’s privilege first , than click “Add”
button for add new user to the list.
Edit button:
Click on the user name of the list first , then modify the data of user . After
modified data , you must click the “Edit” button for confirm modify to list.
Delete button:
Click on the user name of the list , then click “Delete” button for remove user from
list.
44
SecuGuard Basic
1. Main-console
1.5.4 Address Book page at System setup dialog :
Setting address book for send event mail ,or query phone from here.
Add address book record:
Key-in contact information , then click the “Add” button.
Delete address book record:
Click on the row of contact list that you want to delete , then click “Delete” button.
Edit address book record:
1. Select the record that you want to modify.
2. Modify the information , then click “Edit” button.
Change photo of contact:
Click the “▽” button blow of photo ,then select a picture to change.
45
SecuGuard Basic
1. Main-console
1.5.4 Mail page at System setup dialog :
Configuration the E-Mail information for sending event notice mail.
1.5.4.1 SMTP Setting:
Key-in the SMTP server connection
information for sending event notice mail.
Server:
SMTP provider IP address or DNS .
Port:
Mail Server’s SMTP port.
User Name:
account.
Login SMTP server’s user
Password:
Login SMTP server’s password.
From:
The “From” field of E-Mail.
Account Authentication:
Check this box for the SMTP server need authentication
Secure Connection(SSL):
Connect to SMTP with SSL authentication.
Send Test: Click “Send test” button for send a test mail.
46
SecuGuard Basic
1. Main-console
1.5.4.2 Mail Content:
Set the “Subject” and “Body” of send out
mail.
1.5.4.3 Alarm Setting:
Configuration the event
notice mail’s attach snapshot
image rule.
PreAlarm:
Set for how many snapshot image should be captured before event is
triggered.
PostAlarm:
Set for how many snapshot image should be captured after event is
triggered.
Snapshot interval:
Send Interval:
Set the interval betweens of each snapshot.
Set the interval betweens of each send-out notice mail.
Picture Temp Folder:
Select a folder for store snapshot images , these image will delete at system
shutdown.
47
SecuGuard Basic
1. Main-console
1.6 Schedule setup:
Click schedule setup button to approach Schedule setup dialog.
Schedule setup dialog:
48
SecuGuard Basic
1. Main-console
1.6.1 Schedule mode :
Select the schedule mode of system.
The Daily mode and Weekly mode is exclusive
of each other.
Daily mode:
Set schedule time slice by day.
Weekly mode:
Set schedule time slice by weekday.
1.6.2 Select camera of Daily mode :
When you choose Daily mode or click on
“Daily” tab of camera list tree , the tree control will
display all camera installed of system.
Click on the camera name that you want to
modify, the schedule configuration of this camera
will displayed at left of dialog.
System default filled 00:00 to 23:59 round the
clock recording setting , modify it for your own
schedule.
49
SecuGuard Basic
1. Main-console
1.6.3 Select weekday of Weekly mode :
When you choose Weekly mode or click on
“Weekly” tab of camera list tree , the tree control
will display all camera installed of system and the
weekdays as sub item.
Click on the weekday of camera name that you
want to modify, the schedule configuration of this
camera’s weekday will displayed at left of dialog.
System default filled 00:00 to 23:59 round the
clock recording setting , modify it for your own
schedule
1.6.4 Select camera of special day mode :
When you click on “Special Day” tab of
camera list tree , the tree control will display all
special day defined of system and all the camera(s)
installed of system as sub item.
Click on the camera name below of the special
day that you want to modify, the schedule
configuration of this camera’s weekday will
displayed at left of dialog.
System default filled 00:00 to 23:59 round the
clock recording setting , modify it for your own
schedule
50
SecuGuard Basic
1. Main-console
1.6.5 Add and remove special day:
If you want to add a new special day into
system , choose a day from date-time picker
control , then click the “Add” button.
If you want to remove a special day from system , Click the special day on the tree
control at right of dialog , then click the “Delete” button.
1.6.6 Add schedule time slice :
You can define the time slice by several way, please reference as below:
3. Select begin time and end time from date-time picker control:
Click on the hour section or minute
section , then key-in the time value , or
click the “▲” or “▼” to increase or
decrease the time value.
4. Drag time slice bar from
time bar table:
Move mouse cursor to the empty zone at time bar table that you want to add ,
press and hold mouse left button , drag cursor to right until touch the end-time
that you need, then release the left button of mouse.
After drag action , a new gray window was show on the time bar table, and the
window’s left side means this slice’s begin time , right side means end-time.
The mouse cursor must be drag on empty zone , or add mission will not
success.
After time slice define complete , system will popup the “Record Setup” dialog , the
description of this dialog, please reference “Record Setup Page” as below.
51
SecuGuard Basic
1. Main-console
1.6.7 Modify schedule time period:
Step 1 ： Selected the Camera’s name (daily mode) or weekday (weekly mode)
from the tree control at left of dialog.
Step 2 ：
Click on the slice in the list that you wanted to modify.
The other way , you can click on the slice bar in the time bar control.
Step 3 ： Click on the hour section or minute section on the date-time picker
control , then key-in the time value , or click the “▲” or “▼” to increase or
decrease the time value.
Or you can move mouse cursor to edge of slice bar in time bar control , then the
cursor will become to “
” , and drag the edge to the position that you need.
Step 4 ： After complete select the time period , click the “Edit” button for approach
“Record Setup” dialog.
1.6.8 Remove schedule time slice :
Step 1 ： Selected the Camera’s name (daily mode) or weekday (weekly mode)
from the tree control at left of dialog.
Step 2 ： Click on the time period in the list that you wanted to modify.
The other way , you can click on the time period bar in the time bar
control
Step 3 ： Click the “Delete” button at right of dialog.
52
SecuGuard Basic
1. Main-console
1.6.9 Record Setup Page :
1.6.10 Record Mode :
Round the Clock:
When system time reach the schedule time
period , system will begin recording work immediately
and continually until the system time reach this period’s
end-time.
Motion detection:
When system time reach the schedule period
and motion alarm was triggered, system will begin recording work immediately and
continually until the system reach the post-alarm seconds.
DI Detection:
When system time reach the schedule period and DI alarm was triggered,
system will begin recording work immediately and continually until the system reach the
post-alarm seconds.
If the pre-alarm second was set, when motion detection was triggered, the
record data will include pre-alarm seconds by setting.
53
SecuGuard Basic
1. Main-console
1.6.11 Record Setting :
When set to Motion detection or DI detection
record mode, you can set the pre-alarm second(s) at
here , the recording file will keep the setting second(s)
image before alarm was triggered.
Set the Post-Alarm seconds for recording after the event was triggered.
1.6.12 Motion Config :
Motion detect area:
Default button:
Select all image for motion detection.
Add button :
Drag a region on image first , than click “Add” button to add a new
region.
Delete button:
Drag a region on the image , then click “Delete” button for remove the
region that was selected.
Sensitivity :
Set sensitivity level for motion detection , Level 5 means highest motion
detection sensitivity , otherwise , level 1 is the lowest level of sensitivity.
Motion Interval:
Set this value to define each time execute motion detection’s interval.
If set longer value means system will execute less times of motion detection in
minutes, and use less CPU computing power.
54
SecuGuard Basic
1. Main-console
Display Motion detection status:
Checked the check box for display the areas were triggered motion detection.
Preview window:
Red areas are motion
detection area.
Otherwise areas are
non-motion detection area.
The yellow rectangles are
motion detection triggered areas.
1.6.13 DI Record Setting :
When you set the DI Record mode , Select the DI input
from the combo box , and select the DI is open or close to
trigger recording.
1.6.14 Complete Schedule Setting :
Finished configuration job at schedule setting , must be
click “OK” button to return main-console , if you want to abort this job , please click
“Cancel” button.
55
SecuGuard Basic
1. Main-console
1.7 Start & Stop Monitor:
Click Start & Stop Monitor button to control system monitor job.
Start Monitor All:
Checked for start all type of monitor job .
Start Monitor Schedule:
Checked for start the schedule recording job.
If “Start Monitor All” is checked , system will execute all monitor job automatically .
56
SecuGuard Basic
1. Main-console
1.8 E-Map:
Click E-MAP button to approach E-MAP dialog.
E-MAP dialog:
57
SecuGuard Basic
1. Main-console
1.8.1 Camera list:
List all camera(s) is installed in system by camera
index and name.
1.8.2 Add camera to Map:
Drag camera name from camera list to the position of
the Map.
If the dragging camera is exist in Map , the cursor will
become to “
“ , and not allow to add this camera.
1.8.3 Make camera to focus camera:
Double click on the camera icon that you want to
become focus camera.
When the camera become to focus camera , system
will popup a window to display camera’s live preview
image.
1.8.4 Move camera on Map:
You can move the camera position by these ways as below.
1. Press mouse left button and hold on the camera that you want to move , then
drag it to the position that you want.
2. Double click on the camera , make it become to focus camera , then click
“Move” button .
Move the mouse cursor to the new position and click mouse left button.
1.8.5 Rotate camera on Map:
You can rotate camera direction by these ways as below.
1. Press and hold the mouse right button on the camera icon , then rotate the
camera icon until it rotate to the angle that you need.
2. Make camera to focus camera , then click the “Rotation” button until the angle
of camera satisfied you .
58
SecuGuard Basic
1. Main-console
1.8.6 Delete camera on Map:
Make the camera to focus camera , then click the “Delete” button.
1.8.6 Change Map:
Click the “Change Map” button , then select a new map picture.
1.9 Two way Audio :
Click Two way Audio button to switch Two-way Audio status.
When Two-way audio is on , system will post local microphone’s voice to remote
camera.
Start Two way Audio .
Stop Two way Audio.
Two-way Audio function is depend on camera’s capability , This button only
Enabled at when the focus camera has two-way audio capability.
59
SecuGuard Basic
1. Main-console
1.10 PTZ control :
If focus camera has PTZ function , the panel will show PTZ control button(s).
Which button(s) will be show depends on focus camera’s capability.
1.10.1 Speed control:
Move the slider’s thumb to right to make faster speed, and move the thumb to left to
make slower speed.
Speed value works with direction control , zoom and auto pan , make faster speed to
get more effect with action , and make slower speed to get more accurate action.
60
SecuGuard Basic
1. Main-console
1.10.2 Direction control:
Up button:
Move camera up.
Down button:
Move camera down.
Left button:
Move camera to left.
Right button:
Move camera to right.
Left-up button:
Move camera to left-up.
Right-up button:
Move camera to right-up.
Left-down button:
Move camera to left-down.
Right-down button:
Move camera to right-down.
If you need continued direction action , please press and hold the direction button
until the camera move to the target position.
Home button:
Return camera to default position.
61
SecuGuard Basic
1. Main-console
1.10.3 Tour control:
Select a Tour setting from combo box first , then click the “GO” button to start
assigned tour.
Click “Stop” button to stop the tour job.
1.10.4 Preset control:
Select a preset from combo box, the focus camera
will move to preset position immediately.
1.10.5 Auto pan control:
Click “Auto Pan” button to start auto pan job
(navigation).
Click “Stop” button to stop auto pan job.
1.10.6 Zoom control:
Click the zoom-in button for make focus camera
lens zoom-in.
Click the zoom-out button for make focus camera lens zoom-out.
1.10.7 Focus control:
Click “Focus Auto” to force focus camera auto adjust focus status.
Click plus button to increase focus camera focus level.
Click minus button to decrease focus camera focus level.
1.10.8 IRIS control:
Click “IRIS Auto” to force focus camera auto
adjust IRIS status.
Click plus button to increase focus camera IRIS level.
Click minus button to decrease focus camera IRIS level.
62
SecuGuard Basic
2. Playback
2. Playback
Playback is provide history record file(s)’s search , playback , backup , and convert
file format functions.
User could find out the critical image in minutes by playback tools, and backup
these images to user assigned place with user selected period and length.
Click Exit button to leave playback application.
63
SecuGuard Basic
2. Playback
2.1 Search history record file(s) :
Click the Search button on Playback page.
2.1.1 Search history file(s) dialog :
Select the time period and camera(s) by the search dialog.
64
SecuGuard Basic
2. Playback
2.1.2 Select a day to search history file(s):
Click
,
buttons to select
the month that wanted to search history
file(s).
Click on the date to choose a day to
search.
2.1.3 Select record mode(s):
Checked the modes that wanted to search , if
un-check the mode means the search result will not
include this mode.
2.1.4 Start search:
Click the “Search” button to start search procedure, please wait for the search result
to appear on the list control.
2.1.5 Review history record file(s) in search period:
The list control will
display the result of
search procedure.
Blue section: Round the clock record file(s).
Green section: Motion detection record file(s).
Red section: Alarm record file(s).
65
SecuGuard Basic
2. Playback
2.1.6 Assign time period of search result:
1. You can drag mouse cursor on the list control to assign a time period to playback.
2. Choose a time period by the begin time and end time picker control.
3. The selected time period will display as blue section on the list control.
2.1.7 Select the camera(s) to playback:
Select the camera(s) that you wanted to playback.
The system can select maximum 16 camera(s) to playback at once.
2.1.8 Start playback history file(s):
Click the OK button to finish search procedure and start playback ,
or click cancel button to return Playback main page.
66
SecuGuard Basic
2. Playback
2.2 Playback control button(s):
These buttons control playback start ,pause or reverse play and the other operation
about playback , user can control playback procedure thought these buttons.
2.2.1 Play button:
Click play button to start play the selected period’s history file(s).
2.2.2 Pause button:
Click pause button to pause playback stream, some of operations must
entry pause mode first.
2.2.3 Reverse play button:
Click reverse play button to make playback stream direction to reverse
mode.
2.2.4 Stop button:
Click stop button to stop playback stream and return to the first position of
steam.
2.2.5 Next frame button:
When playback in the pause mode , click the next frame button to seek to
next frame.
2.2.6 Previous frame button:
When playback in the pause mode , click the previouse frame button to
seek to previous frame.
67
SecuGuard Basic
2. Playback
2.2.7 Playback speed control:
Turn the speed button to select playback display
speed.
1X: Normal speed.
2X: Double of normal speed
4X: 4X normal speed.
8X: 8X normal speed.
16X: 16X normal speed.
32X: 32X normal speed.
1/2X: Half of normal speed.
1/4X: Quarter of normal speed.
2.2.8 Division control buttons:
Divide to 1 screen.
Divide to 4 screen(s).
Divide to 6 screen(s).
Divide to 9 screen(s).
Divide to 16 Screen(s)
Full screen mode.
68
SecuGuard Basic
2. Playback
2.3 Convert to AVI file:
Click Convert file button to approach Covert file dialog.
2.3.1 Convert file dialog:
Select time period and camera to convert to AVI file by the convert file dialog, The
AVI file can play on most PC with current codec was installed.
69
SecuGuard Basic
2. Playback
2.3.2 Select a day to covert history file(s):
Click
,
buttons to select
the month that wanted to convert history
file(s).
Click on the date to choose a day to
convert file(s).
2.3.3 Assign time period to prepare convert job:
Choose a time period by the begin time and end time picker control.
2.3.4 Select a camera to prepare convert job:
Select a camera id from combo box to convert job.
2.3.5 Select a folder to place converted file:
Click the brows button to select a folder that will place the converted file.
2.3.6 Start converting job:
Click the OK button to start convert job , when convert finished , system will
produce a file to assigned folder.
Click Cancel button to abort convert job.
The converted file name rule as below:
CHXXXYYYYMMDDHHmmssnnn.avi
XXX: camera ID.
YYYY: Execute convert year.
MM: Execute convert month.
DD: Execute convert day.
HH: Execute convert hour.
mm: Execute convert minute.
ss: Execute convert second.
nnn: Execute convert million-second.
Ex:
CH00220090914140253150.avi
70
SecuGuard Basic
2. Playback
2.4 Switch audio play mode:
Click Audio mode button to popup the menu of audio mode.
Select the audio mode from the popup menu , the
checked item means it is the current mode of audio play
now.
Mute: No audio data will played.
Live: Play the live audio stream.
Playback: Play the playback audio stream.
2.5 Playback setting:
Click the Setting button to popup the menu of playback
setting.
Checked the item(s) to change OSD status on the image while the playback.
Display Date: Display the date of recorded on the image.
Display Time: Display the time of recorded on the image.
Display camera name: Display the camera name on the image.
2.6 Snapshot dialog:
Click the snapshot button to approach snapshot dialog , this function is use for
snapshot all playing history file.
71
SecuGuard Basic
2. Playback
2.6.1 Snapshot all dialog:
The snapshot all dialog ,will display all snapshot image on the dialog, you can
choose which image is going to saved and assign the file format and folder.
2.6.2 Select snapshot image:
The dialog displayed all
snapshot images with the camera ID,
resolution , and camera name.
Checked the check box if you
wanted to save this image.
72
SecuGuard Basic
2. Playback
2.6.3 Select output folder:
Click brows button to select a folder to output snapshot images.
2.6.4 Select output file format:
Select the output image file format from the combo box.
2.6.5 Save snapshot images:
Click the OK button to save all selected image , or click cancel button to abort
snapshot job.
2.6.6 Saved image file name:
The saved file name’s rule as below:
CamXXX_NNNNNN_YYYYMMDDHHmmssnnn.jpg
XXX: camera ID.
NNNN: camera name.
YYYY: The image’s year of date.
MM: The image’s month of date.
DD: The image’s day of date.
HH: The image’s hour of time.
mm: The image’s minute of time.
ss: The image’s second of time.
nnn: The image’s million-second of time.
Ex:
Cam000_AM3220 192.168.0.143_20090908111559901.jpg
73
SecuGuard Basic
2. Playback
2.7 Backup history file(s):
Click the backup button to approach backup dialog to select backup file(s).
2.7.1 Backup dialog:
2.7.2 Select backup date and time period:
The select step is the same as select playback time period.
2.7.3 Select backup camera(s) and backup time period:
The select step is the same as select playback camera and time period.
2.7.4 Select output directory:
Click the “Save to” button to select the output directory.
2.7.5 Start backup job:
Click the OK button to start backup job , or click the cancel button to abort backup
job.
74
SecuGuard Basic
2. Playback
2.7.6 Playback backup files:
Execute the Player.exe at backup directory , the operation step is the same as
playback job.
The backup files must place in the same directory , or the playback job will
failed.
2.8 Playback status:
Current Time:
Playback Time:
Play state:
System current time.
The playing video time.
Display play status and speed.
75
SecuGuard Basic
2. Playback
2.9 Operation with sub-screen:
2.9.1 Define display camera(s) sequence :
1.
To switch display sequence in sub-screen(s) , press and hold mouse left
button on source sub-screen , than drag to target sub-screen and release
mouse left button.
2. To switch current sub-window to another camera , click mouse right
button on the sub-screen , than choose the playback camera you needed.
76
SecuGuard Basic
2. Playback
2.9.2 Digital Zoom at sub-screen :
1. Click mouse right button on sub-screen , and checked Digital Zoom.
2. Move mouse cursor to the position that you wanted to digital zoom-in.
3. Move mouse wheel forward until the image satisfied that you needed.
4. Move mouse wheel backward to digital zoom-out.
5. Press and hold mouse left button to drag the image at sub-screen to the
position that you needed.
6. To cancel digital zoom mode , click mouse right button and un-checked
Digital Zoom.
2.9.3 Switch to Full screen :
1. Click mouse right button and checked Full screen on popup menu to
switch to Full screen.
2. Click mouse right button and un-checked Full screen on popup menu to
switch to Full screen.
3. Click “Esc” button or un-checked “Full screen” on popup menu to return
normal display mode.
2.9.4 Snapshot of sub-screen :
4. Click mouse right button and choose Snapshot on popup menu .
5. Configuration with the image by Snapshot dialog.
6. Click Save button and choose the folder that you wanted to save to.
77
SecuGuard Basic
2. Playback
Snapshot dialog:
Bright :
100 = Maximum brightness, -100 = Maximum dark
Contrast:
100 = Maximum strong with Contrast, -100 = Minimum value of Contrast.
Grayscale:
Click to switch image to grayscale mode.
Sharp:
Click Sharp button to increase image sharp level.
Soft:
Click Soft button to increase image soft level.
Reset:
Click Reset button to recover image to original image.
Print:
Click Print button to print out image to printer.
Save:
Click Save button to choose folder and file name to save.
Close:
Close Snapshot dialog.
78
SecuGuard Basic
2. Playback
2.9.5 Smart Search:
Click mouse right button on the channel that you
want to execute smart search , and select the “Smart
Search “ from the popup menu.
Define smart search area:
Add:
select the “Add” status then drag the area that you want to search , the
search area will display by transparented red mask.
Delete:
Remove the selected detect area.
Default: Select whole image for detection.
Check the “Show Search Image” for display the searching video , or un-checked this box
for only display image on the event was found.
Check the “Show Detect Mark” for display the detect result on the image with yellow
rectangle .
Select the “Sensitivity” for define the sensitivity of detection , high level value means the
event will easy to triggered.
Select the “Detect Interval” for define each detect job’s interval time
When the event was triggered , the window on the right will display the event’s image, if
the event is not you need , click the continue button to find next event.
79
SecuGuard Basic
2. Playback
If you found the event that you wanted , click the OK button to return the playback panel,
and all playing channel will seek to the event position synchronized.
Click Cancel button to abort smart search job .
80
SecuGuard Basic
3. Repair Database
3. Repair database
When the Hard-disk is damaged , or you re-install the SecuGuard system , you
should execute the repair database.
Add button:
System will list the current setting record path(s) ,if the system had other directory
was stored record file , you should click add button to add them.
Delete button:
Remove repair path from the list.
OK button:
Start repair database job.
Cancel button:
Cancel repair database job.
81
SecuGuard Basic
3. Repair Database
3.1 Repair database status:
When the repair database job started , repair percentage and remain time will display
on the title bar .
If you want cancel the repair job , please click the close button on the right-up
corner.
When the finished message box was showed , the repair job is done.
82
SecuGuard Basic
4. Un-Install
4. Un-install
1. Click the Un-Install shortcut from Start->All program -> SecuGuard_5.0 ->
Un-Install
2. Remove the installed SecuGuard from Control-panel->Add/revmove Program ->
Select SecuGuard 5.0 -> select Remove .
83