EQUIP™ Series Fixed Mini Dome Network Camera Reference Guide

Transcription

EQUIP™ Series
Fixed Mini Dome
Network Camera
NTSC / PAL
HD4DIP
HD4DIPX
Reference Guide
Document 800-00249 – Rev C – 08/08
Reference Guide
Revisions
Issue
Date
Revisions
A
12/07
New document (Pre-production release).
B
02/08
Production released version of the manual.
C
08/08
Revised production released version for technical review comments; added ™ to
EQUIP; updated back cover.
4
HD4DIP Network Camera Reference Guide
Contents
About This Document . . . . . . . . . . . . . . . . . . . . . . .
Overview of Contents. . . . . . . . . . . . . . . . . . . . . .
Cautions and Warnings . . . . . . . . . . . . . . . . . . . .
FCC Compliance Statement . . . . . . . . . . . . . . . . . .
Manufacturer’s Declaration of Conformance. . . . . . . . . .
North America. . . . . . . . . . . . . . . . . . . . .
Europe . . . . . . . . . . . . . . . . . . . . . . . .
Warranty and Service. . . . . . . . . . . . . . . . . . . . . .
1
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. . . . 11
. . . . 11
. . . . 12
. . . . 12
. . . . 13
. . . . . 13
. . . . . 13
. . . . 13
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2
Installation and Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . .
Unpack Everything . . . . . . . . . . . . . . . . . . . .
Equipment Required . . . . . . . . . . . . . . . . . . .
Overview of Installation Procedure . . . . . . . . . . . . . . . . .
Camera Components and Functions . . . . . . . . . . . . . . .
Mounting the Camera . . . . . . . . . . . . . . . . . . . . . . .
Preparing the Mounting Surface . . . . . . . . . . . . .
Removing the Gimbal. . . . . . . . . . . . . . . . . . .
Installing the Conduit Plug . . . . . . . . . . . . . . . .
Using the Grommet . . . . . . . . . . . . . . . . . . . .
Mounting the Camera. . . . . . . . . . . . . . . . . . .
Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting Power . . . . . . . . . . . . . . . . . . . .
Connecting to a Video Monitor . . . . . . . . . . . . . .
Connecting Audio and Alarms . . . . . . . . . . . . . .
Connecting to a Network via CAT5 Ethernet Connector
Restore Factory Defaults . . . . . . . . . . . . . . . . .
Replacing the Gimbal. . . . . . . . . . . . . . . . . . .
Adjusting the Camera FOV (Field of View) . . . . . . . . . . . . .
Adjusting the Lens Focus. . . . . . . . . . . . . . . . .
Securing the Enclosure Cover . . . . . . . . . . . . . . . . . . .
3
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 17
. 17
. 18
. 18
. 18
20
. 20
. 21
. 21
. 22
. 22
. 23
. 23
. 25
. 25
. 27
. 27
. 27
. 27
. 28
. 28
Configuring Network Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Preparing the Honeywell IP Utility . . .
System Requirements . . . .
Installing the IP Utility . . . . .
Uninstalling the IP Utility . . .
IP Utility User Profiles . . . . .
Logging On to the IP Utility . .
Changing the User Password
User Interface . . . . . . . . .
Document 800-00249 Rev C
08/08
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 31
. 31
. 32
. 32
. 33
. 33
. 34
. 35
5
Contents
Configuring the HD4DIP(X) IP Network . . . . . . . . . .
Discovering Devices . . . . . . . . . . . . . . .
Connecting to Devices . . . . . . . . . . . . . .
Configuring IP Network Settings . . . . . . . . .
Upgrading the Firmware . . . . . . . . . . . . .
Launching the Web-Client Application . . . . . .
Changing the Web-Client Application Password.
4
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 36
. 36
. 37
. 37
. 40
. 40
. 41
IP Camera Web-Client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Overview . . . . . . . . . . . . . . . . . . . . . . .
User Profiles . . . . . . . . . . . . . . . .
Accessing the IP Camera Web-Client . . . . . . . .
First Time Setup Requirements. . . . . . .
Logging On . . . . . . . . . . . . . . . . .
Installing Honeywell IP (ActiveX Plug-in) . .
Logging Off . . . . . . . . . . . . . . . . .
Uninstalling Honeywell IP (ActiveX Plug-in)
Navigating the User Interface . . . . . . . . . . . .
Live View . . . . . . . . . . . . . . . . . . . . . . .
Device Settings . . . . . . . . . . . . . . . . . . . .
Compression Settings . . . . . . . . . . . . . . . .
Compression Settings . . . . . . . . . . .
Audio Settings . . . . . . . . . . . . . . .
Camera Setup . . . . . . . . . . . . . . . . . . . .
Auto Exposure . . . . . . . . . . . . . . .
White Balance. . . . . . . . . . . . . . . .
Video Analytics . . . . . . . . . . . . . . . . . . . .
Video Blurring . . . . . . . . . . . . . . . .
Camera Blinding . . . . . . . . . . . . . .
Camera Field of View Change . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 43
. 43
. 44
. 44
. 45
. 46
. 47
. 47
. 48
. 49
. 49
. 50
. 51
. 52
. 52
. 53
. 54
. 55
. 56
. 57
. 58
Appendix A
Mounting Template. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Appendix B
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Technical Support . . . . . . . . . . . . . . . . . . . . .
Problem: Lens Out of Optical Focus . . . . . . . . . . . .
Problem: Live View Does Not Display the Expected Video
Problem: Cannot Connect to a Device . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 61
. 61
. 62
. 62
Appendix C
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Appendix D
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
6
Figures
Figure 1-1
Camera Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 2-1
Mounting Template Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Figure 2-2
Mounting Holes and Removed Gimbal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 2-3
Conduit Plug Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Figure 2-4
Camera and Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Figure 2-5
Wiring Connection Shown on Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Figure 2-6
Audio and Alarm PINs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Figure 2-7
Normal Alarm States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Figure 2-8
Alarm Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Figure 2-9
Gimbal Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Figure 2-10
Enclosure Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Figure 3-1
IP Utility Logon Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Figure 3-2
IP Utility Change Password Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Figure 3-3
IP Utility User Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Figure 3-4
IP Network Settings Obtained Automatically . . . . . . . . . . . . . . . . . . . . . . . . . 38
Figure 3-5
IP Network Settings Obtained Manually. . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Figure 3-6
IP Utility Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Figure 3-7
Changing Web-Client User Passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Figure 4-1
Internet Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Figure 4-2
Security Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Figure 4-3
Logon Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Figure 4-4
Honeywell IP Installation (ActiveX Plug-in) . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Figure 4-5
Web-Client: Administrator User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Figure 4-6
Web-Client: Guest User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Figure 4-7
Device Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Figure 4-8
Compression Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Figure 4-9
Camera Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Figure 4-10
Video Analytics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Figure 4-11
Video Analytics Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Figure B-1
ActiveX Control Failed Message. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Figure B-2
Install Unknown Software Prompt
Figure 4-1
Limited or No Connection Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Figure 4-1
HD4DIP Side View with Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
08/08
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
7
Figures
8
Tables
Table 1-1
Fixed Mini Dome Network Cameras . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Table 2-1
Audio and Alarm Connector PIN Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Table 3-1
PC Minimum System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Table 3-2
IP Utility User Roles and Privileges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Table 3-3
IP Network Setting Options of the Device . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Table 4-1
User Roles and Privileges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Table 4-2
Tabs/Views in the Web-Client Application . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Table 4-3
Compression Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Table 4-4
Auto Exposure Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Table 4-5
White Balance Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Table 4-6
Blur Threshold Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Table 4-7
Blinding Threshold Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Table 4-8
Scene Change Threshold Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
01/08
9
Tables
10
About This Document
This document introduces the Honeywell HD4DIP(X) True Day/Night Network Camera. It
covers how to install and operate the HD4DIP(X) in a network environment.
This document is intended for system installers, administrators, and operators.
Overview of Contents
This document contains the following chapters and appendixes:
•
•
•
•
•
•
•
•
08/08
Chapter 1, Introduction, introduces the Honeywell HD4DIP(X) Network Camera and
gives a functional overview of its components.
Chapter 2, Installation and Setup, provides procedures for installing cameras, lens
adjustment, and setting up a network camera environment.
Chapter 3, Configuring Network Settings, describes how to install the Honeywell IP
Utility and set up administrator privileges.
Chapter 4, IP Camera Web-Client, describes how the Web-Client application is used
to view video and configure the available settings for the network camera.
Appendix A, Mounting Template, provides a mounting template for the HD4DIP(X)
camera.
Appendix B, Troubleshooting, lists common problems encountered when setting up
the network camera.
Appendix C, Specifications, provides specifications for the HD4DIP(X) camera.
Appendix D, Glossary, is a handy reference for acronyms used in this guide.
11
Cautions and Warnings
Installation and servicing should be performed only by qualified and experienced
technicians to conform to all local codes and to maintain your warranty.
WARNING!
12 VDC/24 VAC models require the use of CSA Certified/UL
Listed Class 2 power adapters to ensure compliance with
electrical safety standards. Power over Ethernet (PoE)
should meet the IEEE 802.3 af PoE standard.
WEEE (Waste Electrical and Electronic Equipment). Correct disposal of this
product (applicable in the European Union and other European countries with
separate collection systems). This product should be disposed of, at the end of
its useful life, as per applicable local laws, regulations, and procedures.
Caution
When powering the camera from 24 VAC, a UPS source should
be considered to ensure satisfactory performance.
FCC Compliance Statement
Information to the User: This equipment has been tested and found to comply with the
limits for a Class B digital device. Pursuant to Part 15 of the FCC Rules, these limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation.
12
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference. For example, try reorienting or relocating the receiving antenna,
increasing the separation between the equipment and receiver, or connecting the
equipment to an outlet on a different circuit.
Caution
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.
This Class B digital apparatus complies with Canadian ICES-003.
Manufacturer’s Declaration of Conformance
North America
The equipment supplied with this guide conforms to UL 60950-1 and CSA C22.2 No.
60950-1.
Europe
The manufacturer declares that the equipment supplied with this guide is compliant with
the essential protection requirements of the EMC directive 89/336/EEC and the Low
Voltage Directive LVD 73/23 EEC, conforming to the requirements of standards EN 55022
for emissions, EN 50130-4 for immunity, and EN 60950 for Electrical Equipment safety.
Warranty and Service
Subject to the terms and conditions listed on the Product warranty, during the warranty
period Honeywell will repair or replace, at its sole option, free of charge, any defective
products returned prepaid.
In the event you have a problem with any Honeywell product, please call Customer
Service at 1.800.796.CCTV for assistance or to request a Return Merchandise
Authorization (RMA) number.
Be sure to have the model number, serial number, and the nature of the problem available
for the technical service representative.
Prior authorization must be obtained for all returns, exchanges, or credits. Items shipped
to Honeywell without a clearly identified Return Merchandise Authorization (RMA)
number may be refused.
08/08
13
14
1
Introduction
The Honeywell HD4DIP(X) color network cameras provide high picture quality remote
video surveillance over a network connection. See Table 1-1 for descriptions of the
camera models.
Table 1-1
Fixed Mini Dome Network Cameras
Model number
Description
HD4DIP
True Day/Night 540 TVL 2.8 – 10 mm VFAI Lens NTSC
HD4DIPX
True Day/Night 540 TVL 2.8 – 10 mm VFAI Lens PAL
Figure 1-1
Camera Overview
Network connection
08/08
15
Introduction
Features
The Honeywell HD4DIP(X) color network camera has the following features:
•
•
•
•
•
•
•
•
•
•
•
16
Built-in high-resolution color video camera with 1/3” CCD image sensor
Fully integrated indoor enclosure with camera and lens for fast and easy installation
Camera housing surface mounts to a wall or ceiling
IP66 rated for dust and water resistance
2.8–10mm Vari-focal Auto Iris lens and day/night switching delivers clear, sharp, color
images in bright daylight as well as in little or no light
12 VDC, 24 VAC and PoE IEEE 802.3 power supply, automatically detected by the
camera
AGC and BLC, both switchable
Better than 50 dB signal-to-noise ratio
Built-in MPEG4 digital signal output at VGA image size with up to 30 fps
Bi-directional audio communication
One alarm input (NO/NC) and one alarm output (Relay)
2
Installation and Setup
This chapter describes how to:
•
•
•
Mount the camera
Adjust the camera for the clearest image
Set up the camera in a network system
Before You Begin
Please read this guide carefully before you install
the HD4DIP(X) network camera.
Keep this guide for future reference.
Before installing the camera, Honeywell recommends that you check
www.honeywellvideo.com/products/cameras/ to find your camera and download the
latest manuals and software updates.
Unpack Everything
Check that the items received match those listed on the order form and packing slip. The
HD4DIP(X) packing box should include, in addition to this User Guide:
•
•
•
•
•
•
08/08
One fully-assembled HD4DIP(X) camera, including factory-installed pigtail power
and video connections
One HD4DIP(X) hardware kit
One bag containing mounting screws
One mounting template
One product warranty
One CD containing the software
17
If any parts are missing or damaged, contact the dealer you purchased the camera from or
call Honeywell Customer Service (see Warranty and Service).
Equipment Required
The following tools may help you to complete the installation:
•
•
•
Drill
Screwdrivers
Wire cutters
Overview of Installation Procedure
Note
Please familiarize yourself with the installation procedure and complete each
step in the exact sequence given.
The initial installation of an HD4DIP(X) camera consists of the following steps:
Step
See …
1
Install the conduit plug.
page 21
2
Mount the camera.
page 20
3
Connect the wiring.
page 23
4
Adjust the camera angle, position, and
focus for optimum image.
page 27
5
Secure the enclosure cover.
page 28
6
Program the camera.
page 36
Camera Components and Functions
The HD4DIP(X) Network Camera consists of a fully-integrated enclosure with camera and
lens. The wiring can be completely concealed to reduce the risk of tampering.
18
Conduit plug
Base
Fan assembly
Interface board
Gimbal base
Gimbal assembly
Turret (dome insert)
Gasket
Dome
08/08
19
Mounting the Camera
Preparing the Mounting Surface
1.
Affix the mounting template (see Appendix A) to the mounting surface as shown in
Figure 2-1.
2.
Pre-drill three holes as indicated on the template, using the recommended hole size
for the screws being used.
3.
Drill out conduit hole, if required (see Installing the Conduit Plug, page 21).
Figure 2-1
Note
20
Mounting Template Guide
Alternate fasteners (preferably stainless steel) can be used, provided they are
not larger than the screw holes on the mounting template.
Removing the Gimbal
To gain better access to the mounting holes and the wiring board, remove the gimbal from
the enclosure base.
Figure 2-2
1.
2.
Mounting Holes and Removed Gimbal
Squeeze the 4
black tabs until
they are free of the
black clips.
Black tabs (x4)
Elevate the hinge
until the gimbal is
above the housing
and you have
access to the
camera board
connections and
mounting holes.
Metal
hinge
Mounting
holes
Black clips (x4)
Installing the Conduit Plug
Your HD4DIP(X) camera enclosure comes with a conduit plug pre-installed in the 3/4 inch
conduit entry on the back. This plug may be removed and installed in the side 3/4 inch
conduit entry (see Figure 2-3).
08/08
21
Figure 2-3
Conduit Plug Installation
Back entry conduit
Side entry conduit
Conduit plug
WARNING!
To minimize moisture leaking into the camera housing,
position the enclosure with the conduit pointing down. After
feeding the cables through (see Wiring, page 23), apply an
appropriate sealant around the conduit connection.
Using the Grommet
If a conduit is not used for cable routing, install the rubber grommet in the conduit hole, then
slit the grommet and feed the cables through (see Wiring, page 23). Seal the grommet to
prevent moisture from entering the housing.
Mounting the Camera
Mount the camera to a wall or ceiling using the supplied screws (see Preparing the
Mounting Surface on page 20).
22
Wiring
Connecting Power
Caution
When connecting a power supply, use either a 12 VDC or 24 VAC
power plug or use a PoE IEEE 802.3 (Power over Ethernet)
compatible hub. To avoid damage to the camera, never connect more
than one type of power supply at the same time.
WARNING!
Note
1.
The use of a CSA Certified/UL Listed Class 2 power supply is
required to ensure compliance with electrical safety
standards.
Check the power source from the external power supply before applying
power to the camera.
Connect the power supply appropriate for your installation:
•
•
Note
12 VDC or 24 VAC power supply (proceed to step 2)
Power over Ethernet (IEEE 802.3 af) 48 VDC power supply
If you are using PoE (802.3 af), power will automatically be supplied to the
camera through the network cable.
2.
Connect to the power supply (see Figure 2-4 on page 24).
3.
Plug the power supply into an appropriate power source. The LED on the RJ45 jack
illuminates to show that the camera is receiving power. If it does not illuminate, check
the terminal block connections and the power source.
Caution
08/08
When powering the camera from 24 VAC, a UPS source should be
considered to ensure satisfactory performance.
23
Figure 2-4
Camera and Cables
24 VAC/12 VDC power
Spot monitor
(see Connecting to a Video Monitor,
page 25)
CAT5 Ethernet connection via network
(see Connecting to a Network via CAT5 Ethernet
Connector, page 27)
Also for Power over Ethernet (PoE 802.3 af)
Figure 2-5
Wiring Connection Shown on Board
Spot Monitor Output
and Video Test Output
Reset button
Audio: Input / Output
Alarm: Input / Output
(see Connecting
Alarms, page 26)
Power - +
RJ45 Ethernet Connector
(see Connecting to a Network via
CAT5 Ethernet Connector, page 27)
Caution
24
For secure installations, surface mounted cables should be protected
by plastic or metal cable covers.
Caution
Installation must be performed by a qualified electrician. The power
wire size for the distance and the number of cameras must be
determined to maintain 24 VAC or 12 VDC at each camera.
Caution
Connect power either from a 24 VAC/12 VDC source or a CAT5
Ethernet connector (PoE); never both at the same time.
Connecting to a Video Monitor
The analog video connection (see Figure 2-4) is available as a test output and should be
used during installation to position, aim and focus the camera, as needed. Connect the
video connector from the camera to the video input connector on your spot monitor.
Connecting Audio and Alarms
Figure 2-6
1
Audio and Alarm PINs
2
Table 2-1
3
5
6
7
8
Audio and Alarm Connector PIN Definitions
PIN
Definition
1
Audio In +
2
Audio In -
3
Audio Out +
4
Audio Out -
5
Alarm In +
6
Alarm In -
7
Alarm Out +
8
Alarm Out -
08/08
4
25
Connecting Audio
The network camera supports bi-directional audio. There are two supported voice band
channels that function in full duplex mode. The camera can transmit audio from the camera
to the client (PC) using any audio source that provides an industry standard line level input
(see the terminal strip as depicted in Figure 2-5). The camera can also receive audio from
the client (PC) and provide an industry standard line level output (3.5 mm stereo or mono
jack) suitable to connect to audio devices. Audio input and output have 600 Ohm
impedance. See Audio Settings on page 52 to configure audio options.
Connecting Alarms
WARNING!
Do not exceed the maximum rating of 12 VDC, 0.5 A on alarm
output connections.
The HD4DIP network camera has one alarm input and one alarm output. Connect
mechanical or electrical switches to the alarm input connection to allow event-triggered
recording. When alarm inputs are configured, the HD4DIP triggers an alarm only when the
normal alarm state (open or closed) changes (see Figure 2-7). See Device Settings on page
49 to configure the alarm inputs.
Figure 2-7
Normal Alarm States
Normally opened
Normally closed
Connect external devices such as sirens or flashing lights to the alarm output connector to
signal users of the camera that an alarm is activated. See Figure 2-8 for alarm connection.
Figure 2-8
Alarm Connection
Alarm
Audio
In
Out
−
+
+
–
The alarm output can be configured to provide normally open or normally closed contacts
(see Device Settings on page 49 to configure the alarm output). Contacts will be rated for
12 VDC @ 0.5 A.
26
Connecting to a Network via CAT5 Ethernet Connector
The main video connection for your HD4DIP(X) network camera is made through the
Ethernet network connection. Connect the CAT5 Ethernet connector (see Figure 2-4) to
your network using an Ethernet (10Base T, 100Base TX) cable.
Note
You can connect your camera to a network or connect it directly to a PC or
laptop using a crossover cable.
Restore Factory Defaults
Your network camera has a Factory Reset switch located inside the camera (see
Figure 2-5). Use this switch to restore your camera options and passwords to their default
settings. Use a pin or straightened paperclip to press and hold the Reset switch for three
seconds.
Replacing the Gimbal
Replace the gimbal by reinserting the black tabs into the black clips before installing the
dome enclosure.
Adjusting the Camera FOV (Field of View)
To adjust the HD4DIP(X) camera:
1.
Apply power to the camera and watch the video on a connected spot monitor (see
Figure 2-4 to connect a spot monitor).
2.
Loosen the setscrew that locks the gimbal assembly in place (see Figure 2-9) to
adjust the horizontal rotation.
3.
Adjust the camera carrier to the desired view.
4.
Re-tighten the locking screw to lock the gimbal assembly in place.
Note
08/08
Orient the camera as shown in Figure 2-9 to maintain the correct picture
orientation.
27
Figure 2-9
Gimbal Adjustment
Angle view
Top view
Setscrew (loosen to
adjust horizontal
rotation)
B
C
Set focal length
(bottom)
Set focus
(top)
Loosen locking screw (inside
conduit entry) to remove the
side conduit plug.
A
Legend
A = Tilt rotation
B = Horizontal rotation
C = Pan rotation
Adjusting the Lens Focus
Lenses are pre-focused at the factory. They may require a final adjustment after installation
in the unlikely event the optical effect of the dome camera causes a slight defocusing of the
lens.
TECH TIP!
To check the focus, hold the dome over the lens while making any adjustments.
To adjust the camera direction, view angle and focus, connect the service monitor cable
(supplied) to the video monitor output.
Securing the Enclosure Cover
When you have set up your camera and completed the network connections (see
Chapter 3, Configuring Network Settings) use the Allen key (supplied) to secure the
HD4DIP(X) dome enclosure to the base with four #8-32 security screws.
28
Figure 2-10
08/08
Enclosure Cover
29
30
3
Configuring Network Settings
The Honeywell IP Utility is used to provide the network connectivity for the network
camera system. The IP Utility automatically discovers Honeywell IP devices on the
network and enables you to configure the device settings. Using the IP Utility, you can
configure the IP network settings, name the cameras, upgrade the firmware on the
cameras, and change the user passwords of the device.
Preparing the Honeywell IP Utility
To perform the tasks required to discover the HD4DIP devices and configure their network
settings, you must first install the IP Utility. After installing and logging on you can set the
passwords for users in order to control access to the IP Utility.
Note
Before installing and using the Honeywell IP Utility, make sure that your
camera is connected to your network through an Ethernet cable (see
Connecting to a Network via CAT5 Ethernet Connector on page 27).
System Requirements
The Honeywell IP Utility must be installed on a work station that meets the following
minimum requirements.
Table 3-1
08/08
PC Minimum System Requirements
Component
Requirement
Operating System
Windows® 2000/XP®
Processor
Intel® Pentium® IV, 3.0 GHz or faster
RAM
512 MB or higher
Web Browser
Micorsoft® Internet Explorer®, V6.0 or later
31
Note
For optimum system performance, we recommend that you ensure your
system requirements are above these minimum configurations.
Installing the IP Utility
Note
You must have Windows administrator privileges to the work station on which
the Honeywell IP Utility is being installed.
To install the IP Config Tool
1.
Insert the product CD into your CD-ROM drive. The Honeywell IP Utility InstallShield
wizard displays.
OR
If the InstallShield does not begin automatically, use Windows Explorer to navigate to
the CD drive, then double-click Honeywell IP Utility Setup.exe.
2.
Follow the steps in the InstallShield wizard.
3.
Click Finish to close the InstallShield wizard and complete the installation process.
4.
Once the installation is complete, a Honeywell IP Utility icon (
desktop. Double-click the icon to launch the IP Utility.
Note
) appears on your
If Bonjour is not detected on the target computer then it will automatically be
installed during the IP Utility installation.
Uninstalling the IP Utility
The IP Utility can be removed:
•
•
Using the Start Menu
Using the Control Panel
Note
32
When removing the IP Utility, you are given the option to uninstall Bonjour
with the IP Utility.
Removing the IP Utility Using the Start Menu
1. Click Start, and then select Programs ➤ Honeywell Video Systems ➤ EQUIP
Series ➤ IP Utility ➤ Uninstall Honeywell IP Utility.
2.
When prompted, click Yes to confirm that you wish to remove the IP Utility.
The IP Utility is removed.
Removing the IP Utility Using the Control Panel
1. Click Start, and then select Settings ➤ Control Panel.
2.
On the Control Panel window, click Add or Remove Programs and then select
Honeywell IP Utility in the Currently installed programs list.
3.
Click Change. The IP Utility Installation Wizard screen appears.
4.
Click Next, and then click Remove. The Honeywell IP Utility is removed.
5.
Click Finish to close the wizard.
IP Utility User Profiles
The installed IP Utility provides two default users: Administrator and Guest. When using the
IP Utility to access a device on the network, only one Administrator can connect to a specific
device at a time; however, as Guest users are limited to viewing network settings, there are
no such restrictions. Table 3-2 describes the roles and privileges for these users:
Table 3-2
IP Utility User Roles and Privileges
User Role
Privileges
Administrator
•
•
•
•
•
•
•
•
View the list of devices available on the network
Connect to the HD4DIP devices
Configure the IP network settings
Upgrade the firmware version
Change the password for the Web-Client applications
Change the password for the IP Utility application
Only 1 Administrator can be logged in at a time
Can enable/disable a device’s Web-Client
Guest Operator
•
View the list of devices available on the network and
their system settings
Logging On to the IP Utility
To log on to the IP Utility:
1.
Click Start, and then select Programs ➤ Honeywell Video Systems ➤ EQUIP
Series ➤ IP Utility.
OR
Double-click
08/08
on the desktop. The logon dialog box appears.
33
Figure 3-1
IP Utility Logon Dialog Box
2.
In the Username drop-down list, select Administrator or Guest.
3.
Type the case-sensitive Password, and then click
appears.
Note
. The Honeywell IP Utility
The default Administrator password is 1234 and the default Guest password
is guest.
Changing the User Password
To change a User’s Password
1.
Click Start, and then select Programs ➤ Honeywell Video Systems ➤ EQUIP
Series ➤ IP Utility.
OR
Double-click the IP Utility icon (
34
) on your desktop.
2.
The logon dialog box appears (see Figure 3-1).
3.
Click Change Password. The IP Utility password dialog box appears.
Figure 3-2
IP Utility Change Password Dialog Box
Passwords are
hidden and replaced
with *** characters.
4.
Select the Username.
5.
Type the current password in the Old Password field.
6.
Type the case-sensitive New Password, and then re-type it in the Verify Password
field.
7.
Click Apply. The password is changed.
Note
You must click Apply after you make changes to any settings to save those
changes. Settings will not be saved unless you click Apply.
User Interface
The user interface of the Honeywell IP Utility provides access to network configuration and
user settings through the:
•
•
•
•
08/08
Title bar
Tabs
Discovery pane
Status bar
35
Figure 3-3
IP Utility User Interface
The About menu on the Title bar
provides information on which version
of software is being used.
Connect /
disconnect icon
Discovery icon
Limited or No
connectivity
The System tab allows you
to edit network settings and
perform firmware upgrades.
The Discovery pane lists
the IP devices found on the
network and enables the
user to connect to them.
The Status bar indicates which user is logged
in and how many devices have been found on
the network, and the status of the connection
and operations performed after connecting.
Configuring the HD4DIP(X) IP Network
Discovering Devices
When you log on to the IP Utility, the devices on the network — including the devices on
other subnets — are automatically discovered and are listed in the Discovery pane. After
the initial discovery, auto-refresh continues to discover devices that are newly added or
removed from the network.
You can also manually refresh the device discovery by clicking the Discovery icon (
located near the top of the Discovery pane.
Note
36
The Multicast protocol needs to be enabled in the LAN (router/switch) to
discover the devices beyond the subnet.
),
Note
Contact your network administrator if you have any questions regarding your
local area network (LAN) or any other network related issues.
Connecting to Devices
Before configuring the IP network settings and changing the password, you must connect
to the HD4DIP(X) device.
To Connect to a Device
•
In the Discovery pane, double-click the device.
OR
•
On the left pane, select the device, and then click
. The network settings for the
connected device are displayed in the System pane.
To Disconnect from a Device
On the Discovery pane, select the device, and then click
Note
.
When you see the Limited/No connectivity icon (
), you cannot fully
connect to the device because of network related issues. Check your network
settings to resolve the issue.
Configuring IP Network Settings
The IP network setting details such as device name, IP address, and subnet mask can be
configured for each connected device.
Updating IP Network Settings Automatically
To update the IP network settings of a device automatically:
1.
In the Discovery pane, select the device and click
2.
Select Obtain an IP Address automatically. Enter the Device Name.
3.
Click Apply. The available IP address, subnet mask, and default gateway are
assigned to the device from the network server automatically.
08/08
. Select the System tab.
37
Note
You must click Apply for your changes to take effect. If you close the screen
before clicking Apply, all your new settings will be lost.
Figure 3-4
Note
IP Network Settings Obtained Automatically
When you obtain an IP address automatically, the network supplies the
camera with a DHCP address. If no DHCP server is present in the network,
the camera will default to an APIPA address (169.254.x.x).
Updating IP Network Settings Manually
To configure the IP network settings of a device manually:
1.
In the Discovery pane, select the device, and click
2.
Click the System tab.
3.
Make sure the Obtain an IP Address automatically check box is not selected.
4.
Under IP Network Setting, enter the following details:
Table 3-3
38
.
IP Network Setting Options of the Device
Option
Description
Obtain an IP
Address
automatically
This option must NOT be checked to assign a static IP
address to the device.
Device Name
The name of the device.
MAC Address
The preset, unique MAC address of the device is used to
identify specific devices.
Table 3-3
Option
Description
IP Address
The IP address of the device on the network.
Subnet Mask
The subnet mask value of the device on the network.
Default Gateway
The default gateway address that connects the device to the
static network.
Note
Caution
5.
IP Network Setting Options of the Device
Changing the network (IP) settings except for the Device Name will cause the
device to restart.
Check the values for the IP network settings before applying them.
Incorrect values might cause a failure when connecting to the HD4DIP
device.
Click Apply. The network settings are updated and a message appears in the status
bar confirming the update.
Note
Figure 3-5
08/08
IP Network Settings Obtained Manually
39
Upgrading the Firmware
Upgrading the Firmware on an HD4DIP Device
1.
Check www.honeywellvideo.com/support/downloads/downloads_cam.html and find
your camera in the list. Click the firmware link to download the file.
2.
In the Discovery pane, select the device to upgrade and click
Figure 3-6
.
IP Utility Firmware Upgrade
3.
Click Upgrade Firmware. Follow the upgrade wizard steps to complete the upgrade.
4.
Click OK. After the firmware upgrade, the device reboots. The device is rebooted. It
takes about 3 minutes to complete the upgrade process.
Note
When you upgrade the firmware, the system reboots and temporarily loses
connection with the camera and stops operation.
Launching the Web-Client Application
You can open individual Web-Client applications for each discovered device from the IP
Utility. To launch the HD4DIP Web-Client application:
1.
From the Discovery pane, select the device you want to launch, and click
2.
From the System tab, click Launch Browser. The Web-Client application of the
selected HD4DIP(X) opens in Internet Explorer.
Note
3.
40
.
To enable or disable the HTTP server, select or clear the Enable HTTP
Server check box. By default, the option is enabled.
Select the user name and enter the password to log on to the application.
Note
You can also launch the Web-Client application by opening your web browser
and entering the URL (network camera IP address) in the Address bar.
Changing the Web-Client Application Password
The IP Utility enables you to change the password for the HD4DIP Web-Client.
To Change the Password of the Web-Client Application
1.
Select the device from the Discovery pane and click
2.
Click the Users tab.
Figure 3-7
.
Changing Web-Client User Passwords
3.
Select the User name.
4.
Type the Old Password.
5.
Type the case-sensitive New Password and then re-type it in the Verify Password
field.
6.
Click Apply. The password is changed.
Note
08/08
41
42
4
IP Camera Web-Client
Overview
The network camera Web-Client is a web-based application that enables you to view
video, listen to audio, and configure camera and sabotage detection settings for the
network camera.
Note
Certain features of the IP Camera Web-Client are user-based and are
available only to the administrator. Guest users are limited to the Live View
tab. Only one Administrator can be logged on at a time, while up to four Guest
users can logon at the same time.
User Profiles
The following table describes the roles and privileges for the HD4DIP(X) Web-Client
application users:
Table 4-1
User Roles and Privileges
User Role
Privileges
Administrator
•
•
•
•
Guest Operator
08/08
•
•
View video and network settings
Configure the alarm settings
Set up the video compression and audio settings
Configure auto exposure and white balance for
the camera
Set up camera sabotage detection settings
Only 1 Administrator can be logged in at a time
•
•
View video
Up to 4 Guests can be logged in at a time
43
Accessing the IP Camera Web-Client
First Time Setup Requirements
Live images can be viewed from an internet browser with the Web-Client interface. An
ActiveX® control must be downloaded to your computer before you will be able to view
video. The security settings on your browser may need to be modified to allow ActiveX
controls to be downloaded. Configure your browser security settings as follows:
1.
Open Internet Explorer on your PC.
2.
On your web browser, select the Tools drop-down menu, then Internet Options.
3.
Select the Security tab (see Figure 4-1).
Figure 4-1
4.
Select Internet and click the Custom Levels security button.
5.
Scroll down the list to the ActiveX controls and plug-ins options and enable all
ActiveX control functions on the list (see Figure 4-2):
•
•
•
•
•
44
Internet Options
Download signed ActiveX controls
Download unsigned ActiveX controls
Initialize and script ActiveX controls not marked as safe
Run ActiveX controls and plug-ins
Script ActiveX controls marked as safe for scripting
Figure 4-2
Security Settings
6.
Click OK on the Security Settings dialog box.
7.
Select Local Intranet and click the Custom Levels security button.
8.
Scroll down the list to the ActiveX controls and plug-ins options and enable all
ActiveX control functions on the list (see step 5).
9.
Click OK on the Security Settings dialog box.
10. Click Apply, then OK on the Internet Options dialog box.
Logging On
Note
Only 1 Administrator user and 4 Guest users can log on to the Web-Client
application at one time.
To log on to the HD4DIP(X) Web-Client
1.
From the IP Utility, see Logging On to the IP Utility on page 33.
OR
From Internet Explorer (v6.0+), enter the URL in the Address bar to display the logon
screen (Figure 4-3).
08/08
45
Figure 4-3
Logon Screen
Device URL in the
address bar
2.
Select either Administrator or Guest from the list, enter the case-sensitive password
and press Enter.
Note
3.
The default password for the Administrator is 1234 and for the Guest user it is
guest.
The Web-Client appears.
Installing Honeywell IP (ActiveX Plug-in)
If this is the first time you’ve logged on, you may have to install the Honeywell IP ActiveX
control. If the InstallShield Wizard opens (Figure 4-4), click Next and follow the rest of the
InstallShield Wizard instructions to complete the installation. When the installation is
complete, you will observe live streaming video.
Note
46
If you are using the Web-Client on a PC that does not have the Honeywell IP
Utility installed, the Honeywell IP Adapter will be installed along with the
Honeywell IP ActiveX. The Honeywell IP Adapter is required to run the
Web-Client application.
Figure 4-4
Honeywell IP Installation (ActiveX Plug-in)
Logging Off
To log off from the HD4DIP(X) Web-Client application, click Logout at the top of the page.
The Logon screen appears.
Uninstalling Honeywell IP (ActiveX Plug-in)
1.
Click Start, and then choose Control Panel. The Control Panel window appears.
2.
Double-click Add or Remove Programs and then select Honeywell IP from the
Currently installed programs list.
3.
Click Change/Remove to remove the component.
4.
Follow the Uninstallshield wizard instructions to completely remove the application.
08/08
47
Navigating the User Interface
The user interface of the HD4DIP(X) Web-Client application consists of multiple
user-friendly views organized by functionality. Access to the views is user controlled.
Table 4-2
Tabs/Views in the Web-Client Application
Tab
Enables you to...
Live View
View video.
Device Information
View the network settings and firmware details of
the camera. Configure the alarm settings.
Compression
Settings
Configure the compression and audio settings.
Camera Setup
Configure auto exposure and white balance for
the camera.
Video Analytics
Configure the camera sabotage detection
settings and view video display.
Figure 4-5
Web-Client: Administrator User
The URL corresponds to the
HD4DIP(X) camera IP Address
as configured in the IP Utility.
Click a Tab to
display the
corresponding view.
48
Screens are divided
between the current
video display and the
configuration options
associated with the view.
The menu bar displays which user
is logged on and provides a link to
log out of the application.
Figure 4-6
Web-Client: Guest User
Logging on as a Guest limits users
to Live View functionality only. See
Live View for more details.
When an alarm is detected,
an alarm message appears
here to notify an operator.
Live View
Live View provides the user with the ability to view live video as currently viewed by the
camera (see Figure 4-5 and Figure 4-6).
Device Settings
The Device Settings view mirrors the information that is available in the Honeywell IP Utility.
It provides network and firmware settings without having to access the IP Utility.
The device Alarm Settings are also configurable in this view. Set the Alarm Input as
Normally Open, Normally Close or Disable. When alarm inputs are connected, the
camera triggers an alarm only when the normal state (open or closed) changes. See
Connecting Alarms on page 26 for more information.
08/08
49
Connect external devices such as sirens or flashing lights to the alarm output connector to
signal users of the camera that an alarm is activated. Set the Alarm Output as Normally
Open or Normally Close. See Connecting Alarms on page 26 for more information.
When an alarm input event is detected, an alarm message appears on the Web-Client
screen (see Figure 4-6) to notify the operator.
Note
Figure 4-7
Device Settings
Compression Settings
The video signal sent to the Web-Client from the camera has a number of settings that can
be edited which effect the video as its displayed in the Web-Client. The Compression
Settings view enables you to configure settings such as Resolution, Frame Rate and Picture
Quality.
50
Note
Figure 4-8
Some of the settings are
inter-dependent and the
options available will
vary accordingly.
The quality of the video displayed can be configured as needed using the Compression
Settings. Remember to click Apply after changing a setting. Use the following table to set
up video compression.
Table 4-3
Setting
Options
Description
Resolution
4CIF, 2CIF, CIF
4CIF is the highest resolution and CIF is the lowest resolution.
Frame Rate
1–30 (NTSC)
1–25 (PAL)
The frame rate that is displayed per second. For NTSC, select from 1 fps (lowest)
to 30 fps (highest). For PAL, select from 1 fps (lowest) to 25 fps (highest).
Priority
Quality, Bit Rate
Choose the Priority selection based on user requirements. If you select Quality,
Target Bit Rate is greyed out and Picture Quality is activated. If you select Bit
Rate, Picture Quality is greyed out and Target Bit Rate is activated.
08/08
51
Table 4-3
Compression Settings (cont’d)
Setting
Options
Description
Picture Quality
Best, Better,
Good
When Quality is selected as the Priority, select the Picture Quality as Good
(lowest visual quality), Better, or Best (highest visual quality).
Target Bit Rate
(kbps)
400–5000 kbps
Enter the Target Bit Rate in kbps (kilobits per second) which represents the
amount of data processed per second.
GOP (No. of
Frames)
1–100
Select the GOP (Group of pictures) number from 1 to 100.
Audio Settings
The network camera supports bi-directional audio. There are two supported voice band
channels that function in full duplex mode. Connect industry standard line level audio input
and output to the back of your camera. See Connecting Alarms on page 26 for more
information.
Audio configuration for your network camera is straightforward. To listen to or capture audio
from the camera, enable the Camera to Client (PC) check box (
). To listen
to audio from the client (PC), enable the Client (PC) to Camera check box.
Camera Setup
The Camera Setup view provides access to the settings used to configure the camera
functionality. The following section explains Auto Exposure and White Balance setup.
Note
52
Figure 4-9
Camera Setup
Auto Exposure
The camera lens, lighting and true day/night options can be configured as needed using
the Auto Exposure settings. Use the following table to set up Auto Exposure options.
Note
Table 4-4
Auto Exposure Settings
Setting
Options
ALC (Automatic Light
Compensation)
DC Iris Level: 1–25 For an automatic iris lens. Adjust the DC Iris Level until the image is
neither too bright nor too dark.
AGC (Automatic Gain Off, 10 dB–30 dB
Control)
BLC (Backlight
Compensation)
Description
Adjust the maximum value of AGC gain. AGC can be Off, or set from
10 dB–30 dB.
Off, Low, Mid, High Prevents the object in the center of the image from darkening when
there is excessive light from behind.
08/08
53
Table 4-4
Auto Exposure Settings (cont’d)
Setting
Options
Description
Flicker Less
Off, On
Eliminates the “flicker” that can appear in an image under certain
lighting conditions (for example, fluorescent lighting).
Day/Night
Auto, Manual On,
Manual Off
Set the moving, mechanical IR filter within the camera to ensure true 24
hour surveillance.
Detect Time
5–60 seconds
Sets the time (5–60 seconds) before the camera switches to Day or
Night mode after detecting a low light condition.
Day/Night must be set to Auto.
DayToNight
1–7
Determines the low light detection level (1–7) when the camera
switches to Night mode. The lower the value, the darker the lighting
conditions before the camera switches.
Note The DayToNight threshold must be set at least 2 less than the
NightToDay threshold setting.
NightToDay
3–9
Determines the low light detection level (3–9) when the camera
switches to Day mode. The higher the value, the brighter the lighting
conditions before the camera switches.
Night Mode
B/W or Color
Sets the color mode as B/W (monochrome) or Color in Night Mode.
Day/Night must be set to Manual On.
White Balance
White Balance ensures that color integrity is maintained in the camera image by
compensating for the temperature color “casts” that different light sources can cause. Use
the following table to set up White Balance options.
Note
Table 4-5
54
White Balance Settings
Option
Description
ATW (Auto Trace White
Balance Mode)
Feedback system that automatically aligns the white
balance (2800°K to 8000°K).
User Fixed
Preset (4700°K)
AWC Auto (Auto White
Balance Control Mode)
Performs faster action than ATW mode without an operating
range. When set to Auto, AWC operates all the time.
Table 4-5
White Balance Settings (cont’d)
Option
Description
Fluorescent
For office environments with fluorescent or tungsten
lighting. Provides the lowest dynamic range of all presets
(4200°K).
MWB (Manual Mode)
Manual white balance mode. Set the Red and Blue gains
from 0–255.
Indoor
General indoor scenes preset (3200°K).
AWC Manual (Auto White Operates AWC mode manually. When the AWC operation
Balance Control Mode)
starts, click Lock to set the present scene’s white balance.
Outdoor
Preset for outside environments and high-contrast scenes
where the camera is focused on the darker areas (6300°K).
Video Analytics
The HD4DIP(X) camera can be configured to detect three types of sabotage detection via
the Video Analytics view (see Figure 4-10): blinding the camera, blurring the video display,
and tampering with the camera field of view. Alarm messages appear above the video
display when camera sabotage is detected (see Figure 4-11).
The user must note that when the following conditions are applicable, the tamper detection
features must be manually disabled to avoid raising false alarms:
•
•
•
08/08
during the configuration of the video display
while text is overlaid on the video
if the video display becomes too dark
55
Figure 4-10
Video Analytics
Each Tamper Detection
Setting provides 3
threshold levels: High
(80%), Medium (50%)
and Low (30%).
Figure 4-11
Video Analytics Message
Video Blurring
The video appears blurred when the camera is exposed to elements such as water. When
this occurs, video blurring in the field of view is detected and shows an alarm message (see
Figure 4-11) above the video display. To detect video blurring:
1.
56
Click the Video Analytics tab.
2.
In the Blur Threshold list, select one of the following options:
Table 4-6
3.
Blur Threshold Values
Value
To detect ...
High (80%)
Maximum video blurring. The alarm message appears when
the video display is blurred by 80% and above.
Medium (50%)
Medium video blurring. The alarm message appears when
Low (30%)
Minimum video blurring. The alarm message appears when
Click Apply.
Note
To turn off video blur detection, select Disable in the Blur Threshold list.
Disable is the default value.
Note
Camera Blinding
An obstacle in front of the camera lens can blind the camera. When this occurs, camera
blinding is detected and shows an alarm message above the video display (see
Figure 4-11). To detect camera blinding:
1.
2.
In the Blinding Threshold list, select one of the following options:
Table 4-7
3.
08/08
Blinding Threshold Values
Value
To detect ...
High (80%)
Maximum blinding. The alarm message appears when the
HD4DIP(X) camera is blinded by 80% and above.
Medium (50%)
Medium blinding. The alarm message appears when the
Low (30%)
Minimum blinding. The alarm message appears when the
Click Apply.
57
Note
To turn off camera blind detection, select Disable in the Blinding Threshold
list. Disable is the default value.
Note
Camera Field of View Change
The Web-Client application can detect tampering of the camera field of view and show an
alarm message above the video display (see Figure 4-11). To detect a camera field of view
change:
1.
2.
In the Scene Change Threshold list, select one of the following options:
Table 4-8
3.
58
Scene Change Threshold Values
Value
To detect ...
High (80%)
Maximum change in the camera field of view. The alarm
message appears when tampering causes 80% and above
change in the HD4DIP(X) camera field of view.
Medium (50%)
Medium change in the camera field of view. The alarm
Low (30%)
Minimum change in the camera field of view. The alarm
Click Apply.
Note
To turn off camera field of view change detection, select Disable in the Scene
Change Threshold list. Disable is the default value.
Note
A
Mounting Template
Apply to clean, dry surface,
free of dust and dirt
HD4DIP
Mounting Template
3 Holes
Use recommended drill bit
as per screws (supplied)
08/08
Conduit Hole
for 3/4” threaded pipe
59
Mounting Template
60
B
Troubleshooting
Technical Support
Prior to calling Honeywell technical support, refer to the following topics for possible
solutions to problems with your HD4DIP(X) camera. To contact the Honeywell Video
Systems technical support team, call 1-800-796-2288 (North America only) or send an
e-mail to [email protected].
Any equipment returned to Honeywell Video Systems for warranty or service repair must
have a Return Merchandise Authorization (RMA) number. The RMA number must be
clearly marked on all return packages and internal paperwork.
Problem: Lens Out of Optical Focus
Possible solutions:
1.
Verify that the lens cap has been removed from the camera. A translucent cap may
be in place and could blur the video if not removed.
2.
This can also be caused by dirt, oil, grease, and fingerprints, and so on, that have
accumulated on the lens or lower dome. Check the lens and dome and clean them,
if needed.
Caution
08/08
Use extreme caution when cleaning the lens and dome so you do
not scratch their optical surfaces. Prepare a washed-out cotton cloth
or lens cleaning paper with alcohol or lens cleaning liquid. Clean by
moving spirally from the lens center towards its rim. Repeat until the
lens is completely clean.
61
Troubleshooting
Problem: Live View Does Not Display the Expected Video
Possible solutions:
1.
Ensure that your web browser settings are configured to allow ActiveX controls (if you
see the message in Figure B-1, your web browser settings have not been configured).
See First Time Setup Requirements on page 44 for information on setting up your
browser.
Figure B-1
ActiveX Control Failed Message
If your internet security settings are set to “Prompt” you to install ActiveX controls, you
may see a warning similar to Figure B-2. Click Install to install the ActiveX control. See
Installing Honeywell IP (ActiveX Plug-in) on page 46 for the installation procedure.
Figure B-2
Install Unknown Software Prompt
2.
Ensure that the network cable from the HD4DIP(X) camera is connected to both the
camera and the network.
3.
Ensure that the camera assembly board DIP switch settings are configured correctly.
Problem: Cannot Connect to a Device
When the following message (Figure 4-1) displays in the status bar of the IP Utility, your
device connection is limited. Usually this warning indicates that your PC and the device
your are connecting to are on different subnets. Contact your network administrator for help
to resolve your network issue(s).
Figure 4-1
62
Limited or No Connection Message
C
Specifications
Note
These specifications refer to all models, except where otherwise noted.
Specifications are subject to change without notice.
Video Signal Specifications
Video Standard:
Scanning System:
Image Sensor:
Minimum Illumination:
(AGC on, 50 IRE)
Horizontal Resolution:
Video Output:
S/N Ratio:
Auto Gain Control (AGC):
Auto Electronic Shutter (ELC):
Lens Iris Control:
White Balance (AWB):
Lens Type:
Focal Length:
Gamma:
Back Light Compensation
(BLC):
Flickerless:
NTSC
PAL
High Res
525/60 lines (NTSC)
625/50 lines (PAL)
1/3” CCD
0.6 lux color/0.4 lux BW
540 TVL
1.0 Vp-p @ 75 Ohms (test only)
50 dB or more (AGC Off)
Off/On, selectable
1/60–1/100,000 sec (NTSC)
1/50–1/100,000 sec (PAL)
Direct Drive (DC)
ATW, User Fixed, AWC (Auto or Manual), Fluorescent,
MWB (Manual Mode), Indoor, Outdoor
2.8 mm to 10.0 mm Vari-focal Auto Iris, F1.3
f = 2.8 mm to 10 mm
0.45
Off/On, selectable (Low, Mid, High)
Off/On, switchable
Electrical Specifications
Input Voltage:
Input Voltage Range:
Surge Suppression
Power Consumption:
08/08
12 VDC/24 VAC, PoE IEEE 802.3af
11–16 VDC, 17–28 VAC
1.5 kW transient
8 W (max)
63
Specifications
Mechanical
Dimensions (WxH):
See diagram (Figure 4-1)
Weight:
3.0 lb (1.3 Kg) camera only
Construction:
Housing: Die cast aluminum
Finish: Light gray powder coating
Dome: Polycarbonate
Connector:
Aux Video Output: 2-pin connector for video test cable
Power Input: Removable screw terminal block
Alarm I/O: Removable screw terminal block
Audio I/O: Removable screw terminal block
Network: RJ45 connector
Environmental
Temperature:
Operating: 14°F to 122°F (-10°C to 50°C)
Storage: -4°F to 140°F (-20°C to 60°C)
Relative Humidity:
Thermostat Operation
0% to 85%, non-condensing
Thermostatically controlled to activate <122°F (<50°C)
IP Specifications
Video Compression
Resolutions
4CIF
2CIF
CIF
Software Update
Frame Rate NTSC/PAL
Video Streaming
Security
Users
MPEG-4 Part 2 (ISO/IEC 14496-2) SP level 0-3
NTSC
704 x 480
704 x 240
352 x 240
PAL
704 x 576
704 x 288
352 x 244
Field Upgradeable
Up to 30/25 fps video in all resolutions
MPEG-4 controllable frame rate and bandwidth.
Constant and variable bit rate (MPEG-4)
Multiple user access levels with password protection
1 Administrator; 4 Guests
Video access from web
browser
Camera live view for up to 5 clients. Full control of all
camera settings available to administrator
Minimum web browsing
requirements
Pentium IV CPU 3.0 GHz or equivalent AMD
512 MB RAM
AGP graphics card (32 MB RAM)
Windows 2000/XP
Internet Explorer 6x or later
Installation, Management, and Honeywell IP Utility software identifies the IP address,
Maintenance
checks the status of the device. Firmware upgrades over
HTTP, firmware available at www.honeywellvideo.com.
Supported Protocols
IPv4, HTTP, TCP, RTSP, RTP, UDP, IGMP, RTCP, FTP,
ICMP, DHCP, Bonjour, ARP, DNS
Regulatory
Emissions
FCC, CE (EN55022)
Immunity
CE (EN50130-4)
Safety
EU: 73/23/EEC LVD
Mounts
64
HD4DIP-PK
Pendant mount bracket
HD4DIP-WK
Wall mount bracket
Figure 4-1
HD4DIP Side View with Dimensions
5 0 1 .9
.4 8”
m
m
1.81”
46.0 mm
2.64”
67.0 mm
4.61”
117.5 mm
6.1”
154.97 mm
08/08
65
Specifications
66
D
Glossary
AGC (Automatic Gain Control) Video Amplifier in a camera that boosts the amount of
video gain (including the noise) to maintain a 1V p-p (1-volt peak-to-peak) video signal
output. It becomes operational when the light level is low. The circuit is designed to
compensate for fluctuations in scene illumination which would cause the video output
level to be too low. If the video level is adequate, the circuit does not apply any gain to the
signal. As the video level (scene illumination) falls, more and more gain is applied by the
AGC circuit to the video signal.
ALC Setting in an Auto Iris lens to control the iris opening. Adjusts between peak and
average to respond to the bright part of the scene (peak setting) or the average value of
the video signal (average setting).
BLC (Backlight Compensation) Improves the image quality when you have a scene
where the brightest light in the scene comes from behind the subject of interest (for
example, a dark vehicle with the sun setting behind it or a person entering an office from
the brighter-lit outside). What happens is the camera’s exposure circuit sets itself to the
average light level in the scene and uses this to adjust the electronic iris. For example,
when someone opens the door, the exposure system reacts to the increased light level,
leaving a person entering the room in silhouette.
The backlight compensation feature uses a "window" — usually fixed to the central portion
of the scene —to set the exposure so that everything outside the window is ignored by
the exposure system. Some cameras allow you to select different windows, control the
size and position of the window, and select the amount of exposure compensation
applied to the selected areas.
DHCP (Dynamic Host Configuration Protocol) Allows a server to dynamically assign
IP addresses to nodes (workstations) automatically. Provides client information including
subnetwork mask, gateway address, and DNS (Domain Address Server) addresses.
Flickerless Eliminates the “flicker” that can appear in an image under certain lighting
conditions (for example, fluorescent lighting). This is usually caused by the interaction of
the shutter with the AC frequency of the lighting. The flickerless setting changes the
shutter speed of the camera to a value that will not cause flicker (1/100 sec, NTSC, 1/120
sec for PAL). The side effect is that the camera sensitivity is reduced because the
electronic iris feature has effectively been turned off and will no longer control the
optimum exposure setting for available light conditions.
FOV (Field of View) The part of the scene visible with a particular lens. The height
(horizontal) and width (vertical) picture size at a given distance that can be seen through
a lens. Generally, shorter focal length lenses have a wider field of view than those with
longer focal lengths.
Gain The amplification a system provides to a signal.
IP Address A unique, 32-bit identifier for a specific TCP/IP host computer on a network.
08/08
67
Glossary
Iris Adjust Adjusts the iris either open or close in response to changing light conditions.
Line Lock Phase Adjust (LL-Phase Adjust, or Line Lock) When the camera is in Line
Lock mode it is synchronized using a fixed point on the A.C. supply’s cycle - usually the
point that the A.C. cycle passes through zero V. Usually selected by a switch on the side or
rear of the camera. This is commonly used to synchronize the vertical interval sync pulse of
your camera with other equipment in a switching system to reduce the effect of picture roll
on the monitor when two or more cameras cover a large site . You must phase the phase
for each camera. If multiple cameras are not synchronized correctly, the image on the
monitor rolls as the video switcher selects video from different cameras (frames arrive at the
video switcher at different times).
To utilize this feature, cameras must operate from an AC supply and be on the same Mains
supply phase. If they are not on the same phase, you can adjust them using the V-PHASE
potentiometer on the camera.
NTSC (National Television Standards Committee) A standard of specifications for
television transmission in the U.S., Canada, Japan, Central American, and half of South
America. The North American system uses interlaced scans and 525 horizontal lines per
frame at a rate of 30 frames per second.
PAL (Phase Alternate Line) A standard of specifications for television transmission for
color TV signals used in West Germany, England, Holland, Australia, and several other
countries. It uses an interlaced format with 25 frames per second and 625 lines per frame.
PoE (Power over Ethernet) A system designed to transmit electrical power, along with
data, to remote devices over standard twisted pair cable in an Ethernet network.
Shutter Speed The speed at which the charge is read out from the CCD chip. Adjusts the
light sensitivity of the camera. A faster (briefer) shutter speed can arrest the motion of a fast
moving object (reduce image blur), rendering it sharp. Fast shutter speeds allow less light
to all on the CCD and can darken the image. For fast shutter speeds, ensure there is
adequate lighting. Usually selected using dip switches on the side of the camera.
Subnet Mask A number used to identify a subnetwork so that an IP address can be shared
on a LAN.
True Day/Night The incorporation of a moving mechanical IR filter within the camera
ensures true 24 hour surveillance, providing high quality color images during the day and
similar quality black & white images at night when used with IR lighting.
68
Index
A
G
administrator, privileges 33
alarms, connecting 26
guest/ operator, privileges 33
I
B
IP Config Tool
changing password 34
installing 32
user interface 35
user profile 33
IP network settings
configuring 31
default gateway 39
device name 38
IP address 39
MAC address 38
subnet mask 39
IP Utility
configuring network settings 37
connecting to devices 37
discoving devices 36
GUI 35
installing 32
launching web client 40
logging on 33
removing 32
upgrading firmware 40
user password 34
user profile 33
BLC, adjusting 28
browser, launching 40
C
cabling, connecting 23
camera
adjusting 27
components 18
mounting 20
CAT5 Ethernet connector 27
compression settings 50
conduit plug, installing 21
connections
alarms 26
CAT5 Ethernet 27
video monitor 25
D
discovering devices
auto-refresh 36
F
L
features, camera 16
firmware
upgrading 40
functions, camera 18
Rev C
launch browser 40
lens focus, adjusting 28
line lock, adjusting 28
logging on
IP Utility 33
69
Document 800-00249
08/08
user password
changing via IP Utility 41
IP Utility 34
user profile 33
M
mounting template 20, 59
N
V
network settings 37
video monitor, connecting 25
P
W
password, changing 34
PC system requirements 31
power, connecting 23
web client
changing password via IP Utility 41
launching 40
launching via the IP Utility 40
wiring
alarm connection 26
connections on board 24
T
troubleshooting 61
U
user interface, described 35
Rev C
70
Document 800-00249
08/08
Honeywell Video Systems (Head Office)
2700 Blankenbaker Pkwy, Suite 150
Louisville, KY 40299, USA
www.honeywellvideo.com
℡ +1.800.796.2288
Honeywell Security UK
Aston Fields Road, Whitehouse Ind Est
Runcorn, Cheshire, WA7 3DL, UK
www.honeywell.com/security/uk
℡ +44.1928.756.999
Honeywell Security Australia Pty Ltd.
Unit 5, Riverside Center, 24-28 River Road West
Parramatta, NSW 2150, Australia
www.honeywellsecurity.com.au
℡ +61.2.8837.9300
Honeywell Video Systems Northern Europe
Netwerk 121
1446 WV Purmerend, The Netherlands
www.honeywell.com/security/nl
℡ +31.299.410.200
Honeywell Security Asia Pacific
33/F Tower A, City Center, 100 Zun Yi Road
Shanghai 200051, China
www.asia.security.honeywell.com
℡ +86 21.5257.4568
Honeywell Security Deutschland
Johannes-Mauthe-Straße 14
D-72458 Albstadt, Germany
www.honeywell.com/security/de
℡ +49.74 31.8 01.0
Honeywell Security Asia
Flat A, 16/F, CDW Building, 388 Castle Peak Road
Tsuen Wan, N.T., Hong Kong
www.asia.security.honeywell.com
℡ +852.2405.2323
Honeywell Security France
Parc Gutenberg, 8, Voie La Cardon
91120, Palaiseau, France
www.honeywell.com/security/fr
℡ +33.01.64.53.80.40
Honeywell Security South Africa
Honeywell House, Bekker Street
Truer Close, Waterfall Park
Midrand 1685, South Africa
www.honeywell.com/security/za
℡ +27.11.695.8000
Honeywell Security Italia SpA
Via della Resistenza 53/59
20090 Buccinasco
Milan, Italy
www.honeywell.com/security/it
℡ +39.02.4888.051
Honeywell Security Middle East
Honeywell Middle East FZE
Post Office Box 18530
LOB Building 08, Office 199
Jebel Ali, Dubai U.A.E.
www.honeywell.com/security/me
℡ +971.04.881.5506
Honeywell Security España
Mijancas 1. 3a planta
P.Ind. Las Mercedes
28022 Madrid, Spain
www.honeywell.com/security/es
℡ +34.902.667.800
www.honeywellvideo.com
+1.800.796.CCTV (North America only)
[email protected]
Document 800-00249 – Rev C – 08/08
© 2008 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written
permission from Honeywell Video Systems. The information in this publication is believed to be accurate in all respects. However,
Honeywell Video Systems cannot assume responsibility for any consequences resulting from the use thereof. The information
contained herein is subject to change without notice. Revisions or new editions to this publication may be issued to incorporate such
changes.

EQUIP™ Series Fixed Mini Dome Network Camera Reference Guide

Transcription

Similar documents

COBRACAM PRO

SceneTracker From DVTEL

June

ele ctronics - rv care online catalog

ximea mq022

Photographer: David Fincher / Model: Rooney Mara / Shot on RED

August 2015 - Gene`s Camera Store

Trix Rabbit Story board

AkonA Pro CAmerA BAg

Remotec Andros TM F6