3221 Thumbturn Only Deadbolt

3221 Thumbturn Only Deadbolt
Installation Instructions
LATCH
FOR USE ON DOORS 1-3/8" to 1-3/4"
(35mm-45mm) THICK
DEADBOLT
LATCH MOUNTING PLATE
TOOLS REQUIRED FOR NEW INSTALLATION:
(1) Phillips Head Screwdriver
(1) 2-1/8" (54mm) Hole Saw
(1) 1" (25.4mm) Drill Bit
(1) Chisel
STRIKE
THUMB TURN
ASSEMBLY
WOOD FRAME
REINFORCER
DUST BOX
TOOLS REQUIRED FOR REPLACEMENT INSTALLATION:
(1) Phillips Head Screwdriver
DOOR EDGE
FOR REMODELING OR NEW CONSTRUCTION:
- Follow all steps
MOUNTING SCREWS
DOOR FACE
DOOR EDGEDOOR EDGE
1. MARK DOOR
2. DRILL HOLES
DOOR EDGE
DOOR FACEDOOR FACE
1"(25.4mm) HOLE
4-1/8"(105mm)
DEEP
2-1/8" (54mm) HOLE
1-3/16" (31mm) DEEP
DOOR FACE
1"(25.4mm) 1"(25.4mm)
HOLE
HOLE
4-1/8"(105mm)
4-1/8"(105mm)
Measure center DEEP
line of lock; height as desired from finished floor.
DEEP
Select 2-3/4" or optional 2-3/8" backset, fold and apply template
to interior side of door and mark center of door as indicated on
template. Mark center
hole on
door
face through
2-1/8" (54mm)
HOLE
2-1/8"
(54mm)
HOLE guide on template.
1"(25.4mm)
HOLE
(See Step 7 for 1-3/16"
changing
latch
backset)
(31mm)
DEEP
1-3/16" (31mm) DEEP
3. PREP DOOR
4-1/8"(105mm)
DEEP
Drill 1" (25.4 mm) hole 4-1/8" (105 mm) deep in center of door edge.
Drill 2-1/8" (54mm) hole 1-3/16" (31 mm) deep on interior door face.
CAUTION:
Do not drill completely through the door face.
2-1/8" (54mm) HOLE
b.
1-3/16" (31mm) DEEP
a.
Insert latch in hole, keeping latch face parallel to
face of door edge.
Mark outline and remove latch.
c.
Refer to Step 5 & 6 when installing latch.
Chisel 5/32" (4 mm) deep or
until latch face is flush with door edge.
TEMPLATE
T E MP L A T E
2-1/8" (5 4 mm) HOLE
FOLD HERE
ON DOOR EDGE
2-3/8" ( 60mm ) BACKSET
45
40
35
2-3/4" ( 70mm ) BACKSET
1-3/4" 1-9/16" 1-3/8"
Make 1"(25.4mm) hole at center
of door edge.
CAUTION：
DO NOT DRILL 2-1/8" (54mm) HOLE
THROUGH TO OPPOSITE SIDE OF DOOR.
(READ INSTRUCTIONS CAREFULLY)
HAGER COMPANIES139 Victor Street, St. Louis, MO 63104 (800) 325-9995 FAX (800) 782-0149
7/28/08
LATCH MOUNTING PLATE
4. INSTALL STRIKE
a.
b.
Close door. Locate strike in jamb
and center line of strike. Open
door and extend line to door stop.
Measure half of door thickness
plus 1/8" from door stop. Vertically
mark centerline for strike.
c.
Drill (2) 1"(25.4 mm) holes 1-1/4" (31.7 mm)
deep in door jamb, 5/16" (8 mm) above and
5/16’" (8 mm) below horizontal center line.
CAUTION:
Hole must be drilled a full 1-1/4" (31.7 mm)
deep to ensure proper functioning.
5. INSTALL LATCH MOUNTING PLATE
SIDE VIEW ASSEMBLED
Match screw holes on strike with
vertical centerlines on jamb. Mark
outline of strike and chisel 1/4"
(6.4mm) deep for flush fit of dust
box, wood frame reinforcer, and
RELEASE
strike. Place dust box and
wood
SWITCH
frame reinforcer into mortised area
and tighten to the frame using 3"
wood screws. Insert the strike and
tighten to the frame with #8 screws.
2-3/8"
BACKSET
2-3/4"
BACKSET
6. INSTALL LATCH THUMBTURN ASSEMBLY
LATCH
CRANK
LATCH
PLATE
TORQUE BLADE
Adjust the latch to the proper
backset, see below for details
on adjusting the latch.
THUMBTURN
ASSEMBLY
Insert the latch mounting plate
into the holes on the latch.
LATCH MOUNTING PLATE
Insert latch into 1" diameter hole and tighten to the door edge using #8 screws.
Insert torque blade horizontally into latch crank until thumb turn assembly is
flush with door face. Tighten assembly using screws.
LATCH MOUNTING PLATE
SIDE VIEW ASSEMBLED
Note: When installing on a metal door, the latch mounting plate may be pulled
up against the inside door face as the mounting screws are tightened. This is
normal when installing on a metal door.
SIDE VIEW ASSEMBLED
RELEASE
SWITCH
7. BACKSET ADJUSTMENT
RELEASE
SWITCH
2-3/8"
BACKSET
To set latch to 2-3/8" setting, pull up Release Switch on both sides.
While holding Release Switch up, slide crosshairs to the 2-3/8" marked hole.
2-3/4"
BACKSET
2-3/8" LATCH
BACKSETCRANK
2-3/4"
BACKSET
LATCH
PLATE