"Lily" beaded bead - CzechBeadsExclusive

"Lily" beaded bead
Small beaded rondelle with pinch beads and Superduos
Material (for one bead):
Matubo Superduo (10 pcs)
Pinch beads (15 pcs)
Matubo 8/0s (10 pcs)
15/0 Japanese seed beads (approx. 0,5 gram)
11/0 Japanese seed beads (approx. 0,5 gram)
8mm round acrylic or wooden bead
Beading needle and thread (Nymo, Fireline)
Difficulty: Beginner/Intermediate
1 | Design and tutorial by Nela Kábelová (www.gianelle.beadforum.cz)
Autorem tohoto designu a návodu je Nela Kábelová (www.gianelle.beadforum.cz)
Find all beads for this project on
www.CzechBeadsExclusive.com
(click here!)
www.matubobeads.com
TIP: Right angle weave can be a bit tricky when it comes to
6) Repeat steps 3 - 5 two more times. You should
keeping the right tension. If you have trouble keeping your have a strip that is 4 "units" long.
tension tight, you can weave through each unit one more
time before moving on to another one.
1) String four pinch
beads and slide them
to the end of the
thread.
2) Tie a square knot.
The beads should form
a little square.
Pass through the
7) Add one pinch bead
nearest pinch bead.
and pass through the
pinch bead on the
opposite side of the
strip.
3) Add three more
pinch beads and pass
through the pinch bead
from the previous step
again.
8) Add one more pinch
bead and pass through
the "first" pinch bead
again.
4) Pull snug. Then pass
through the nearest
new pinch bead ...
9) Pull snug.
This is how the base
of our beaded bead
looks like.
5) ... and then through
the next one.
2 | Design and tutorial by Nela Kábelová (www.gianelle.beadforum.cz)
Autorem tohoto designu a návodu je Nela Kábelová (www.gianelle.beadforum.cz)
Find all beads for this project on
www.CzechBeadsExclusive.com
(click here!)
www.matubobeads.com
10) Pass through the
15) Add two 15/0s, one
nearest pinch bead.
Superduo, one 11/0,
one Superduo and two
15/0s. Pass back
through the
corresponding 11/0 on
the other side of the
11) Add one 11/0 and
bead.
pinch bead in the row.
16) Add two 15/0s, one
pass through the next
Superduo, one 11/0,
one Superduo and two
15/0s. Pass through
the same 11/0 you
started from in the
12) Repeat step 11, until you reach the end of the
row.
previous step ...
17) ... and then pass
through the next pinch
bead and through the
next 11/0 in the row.
13) Weave through
beads to get to the
other side of the bead.
18) Add another "loop"
of beads - two 15/0s,
one Superduo, one
11/0, one Superduo and
two 15/0s - and pass
back through the
14) Put the core bead inside and then repeat
corresponding 11/0 on
the other side of the
steps 11, until you reach the end of the row.
bead.
passing through the first 11/0 from this row.
19) Add two 15/0s and
At the end of the row make the step-up by
go up through the
"unused" hole of the
nearest Superduo (as
shown in the photo).
3 | Design and tutorial by Nela Kábelová (www.gianelle.beadforum.cz)
Autorem tohoto designu a návodu je Nela Kábelová (www.gianelle.beadforum.cz)
Find all beads for this project on
www.CzechBeadsExclusive.com
(click here!)
www.matubobeads.com
20) Add one 11/0 and
24) When you reach the
go up through the
end of the row, add
next Superduo.
through the "unused"
"unused" hole of the
two 15/0s and pass
hole of the
nearest
Superduo (it is the one
we added in step 16).
21) Add two 15/0s and
25) Add one 11/0 and
11/0 between the pinch
"unused" hole of the
pass through the next
beads.
go down through the
next Superduo.
22) And then pass
through one pinch bead
and one 11/0.
26) Add two 15/0s and
pass through the
nearest 11/0 between
the pinch beads (like
shown in the picture).
23) Repeat steps 18 - 22 two more times.
27) Add two 15/0s and
go up through the
"unused" hole of the
nearest Superduo (as
shown in the photo).
28) Add one 11/0 and
go up through the
"unused" hole of the
next Superduo.
4 | Design and tutorial by Nela Kábelová (www.gianelle.beadforum.cz)
Autorem tohoto designu a návodu je Nela Kábelová (www.gianelle.beadforum.cz)
Find all beads for this project on
www.CzechBeadsExclusive.com
(click here!)
www.matubobeads.com
29) Add two 15/0s and
35) ... until you reach
pass through the next
the end of the row.
11/0 between the pinch
beads.
30) The thread exits
36) You can weave
Add one 15/0, three
few more times.
from one of the 11/0s.
through the last row
11/0 and one 15/0 and
pass through the next
11/0 in the row.
37) Weave through
beads to get to the
31) Repeat step 30,
other side of the bead.
until you reach the end
of the row.
38) Repeat steps 30 - 36 on the other side of the
bead.
32) At the end of the
row make the step-up
by passing through the
first 15/0 and two
11/0s added in this
row.
33) The thread exits
from the "middle" 11/0.
Add one 8/0 and pass
through the "middle"
11/0 from the next
loop.
34) Repeat step 33 ...
39) Tie a few half-
hitch knots and cut off
all the remaining
thread. The bead is
finished.
5 | Design and tutorial by Nela Kábelová (www.gianelle.beadforum.cz)
Autorem tohoto designu a návodu je Nela Kábelová (www.gianelle.beadforum.cz)
Find all beads for this project on
www.CzechBeadsExclusive.com
(click here!)
www.matubobeads.com