installation instructions

GENUINE PARTS
INSTALLATION INSTRUCTIONS
1. DESCRIPTION:
In-mirror RearView Monitor
2. APPLICATION:
Altima Sedan & HEV (2007~)
Altima Coupe (2008~)
3. PART NUMBER: 999Q6 VV000
4. KIT CONTENTS:
Item
Qty
Description
Service Part Number
A
1
In-mirror RearView Monitor
999Q6 VV020
B
1
Camera
999Q6 VV030
C
1
Parts Kit
999Q6 VV060SP (Items D - O)
D
1
Harness
E
1
Camera Bracket
F
1
Camera Grommet
G
1
Wire Cover
H
47
Wire Tie
I
15
Foam Tape
J
1
Butyl Gum
K
2
Posi-Tap™
L
2
M3 x 6 Phillip Screw
M
2
6/32 x 3/8 Phillip Screw
N
2
Speed Nut
O
1
User Guide
P
1
Manual, Installation Instruction Download
5. PRE-INSTALLATION CAUTION / NOTES:
WARNING
• Disconnect vehicle battery before installing In-mirror RearView Monitor Kit to prevent possible shock injury
during installation.
!
CAUTION
• Dealer installation recommended. This installation instruction will reference the service manual.
• This is a universal installation kit so all parts may not be used.
• Cut the excess wire tie(s) as flush with the head as possible. Face head of cable tie away from sheet
metal and other objects.
• Use caution when removing/re-installing interior components to avoid damage, scratches, or breaking of
mounting clips.
Page 1 of 25
Rev. 11-24-08
In-mirror RearView Monitor - Altima
!
CAUTION
• Ensure the slack on the installed harness is removed before securing wire ties.
• The harness routing needs to be followed as described to avoid interferences.
• Trim removal may differ among Altima sedan, HEV, and coupe models. Reference installation instructions
for correct procedure.
6. TOOLS REQUIRED:
1. Clean Rag
4. 4mm Flat Screwdriver
7. 8mm Socket Wrench
10. 50/50 Alcohol / Water
Solution
2. Needle Nose Pliers
5. Panel Removal Tool
8. #2 Phillip’s Screwdriver
3. T-20 Torx Head Driver
6. 10mm Socket Wrench
9. Dremel Tool or Equivalent 11. Fish Wire
7. VEHICLE PREPARATION:
1) Apply parking brake.
2) Record the customer radio presets.
Presets
1
2
3
4
5
6
7
A
B
C
D
3) Make sure that the shift lever is engaged in the “P” position.
4) Turn the ignition switch OFF.
5) Open engine hood.
PRECAUTION FOR HIGH-VOLTAGE CIRCUIT (For sedan / coupe vehicle’s, proceed to 8. INSTALLATION
PROCEDURE
NOTE:
The hybrid system contains a 244.8 V high-voltage system with a strong alkali solution of potassium hydroxide . Be sure to follow the instructions in this manual to handle the system correctly. Failure to do so may
result in serious injury or electrocution.
1. Engineer must undergo special training to be able to perform high-voltage system inspection and servicing.
2. High-voltage cables are colored orange. The HV battery and other high-voltage components have “high
voltage” caution labels. Do not carelessly touch these wires and components.
3. Before inspecting or servicing the high-voltage system, be sure to follow safety measures, such as wearing insulated gloves and removing the service plug to prevent electrocution. Carry the removed service
plug in your pocket to prevent other technicians from reinstalling it while you are service the vehicle.
Page 2 of 25
Rev. 11-24-08
In-mirror RearView Monitor - Altima
NOTE:
• Before removing the service plug, confirm ignition switch is off.
• Do not put the vehicle into the ON (READY) state after removing the service plug grip as the ECU may
be damaged.
• ON (READY): The condition which the ready indicator lamp illuminates and vehicle is ready to be
driven.
• Turn the ignition switch off, wear insulated gloves, and disconnect the negative terminal of the auxiliary
battery before touching any of the orange-colored wires of the high-voltage system.
• Turn the ignition switch off before performing any resistance checks.
• Turn the ignition switch off before disconnecting or reconnecting any connectors.
4.
5.
6.
7.
After removing the service plug, wait 10 minutes before touching any of the high-voltage connectors and
terminals.
NOTE:
10 minutes are required to discharge the high-voltage condenser inside the inverter.
Before wearing insulated gloves, make sure that they are not cracked, ruptured, torn, or damaged in any way.
Do not wear wet insulated gloves.
When servicing the vehicle, do not carry metal objects like mechanical pencils or scales that can be dropped
accidentally and cause a short circuit.
Before touching a bar high-voltage terminal, wear insulated gloves and use a tester to make sure that the
terminal voltage is 0 V.
DO NOT WEAR
Page 3 of 25
Rev. 11-24-08
In-mirror RearView Monitor - Altima
8. INSTALLATION PROCEDURE:
Fig. 1
Auto-Dimming
Mirror
Fig. 2
Prism Mirror
1) Disconnect negative battery terminal.
2) Removal of OE Rearview Mirror (Auto-Dimming Mirror)
a) Using a T-20 Torx head driver, loosen the screw
on the mirror mount. (Fig. 1)
b) Slide the EC mirror base off from the button on
the windshield. (Fig. 1)
c) Unplug the harness connector from the back of
the Auto-Dimming Mirror.
3) Removal of OE Rearview Mirror (Prism Mirror)
a) Insert the flat end of a 3mm screwdriver into
the opening at the bottom of the mirror mount.
(Fig. 2)
b) Slide the screwdriver upward into the center of
the mirror mount until resistance is felt. Apply a
small amount of additional upward force to lift a
locking spring in the mount. (Fig. 2)
c) While still applying upward pressure with the
screwdriver, grasp the mirror bracket and lift
the mirror up towards the headliner and off the
mirror mounting bracket. (Fig. 2)
4) Remove the following interior parts as shown in Fig. 3 (Refer to vehicle service manual)
a) LH Front Kicking Plate
b) LH Dash Side Lower Finisher
c) LH Instrument Side Mask
d) LH Front Body Side Welt
e) LH Front Pillar Finisher
f) LH Rear Kicking Plate (Sedan / HEV Only)
g) LH Rear Body Side Welt (Sedan / HEV Only)
h) LH Center Pillar Lower Finisher (Sedan / HEV Only)
i) LH Front Fuse Cover
j) Rear Seat Bottom Cushion
k) LH Rear Lower Finisher (Coupe Only)
Page 4 of 25
Rev. 11-24-08
In-mirror RearView Monitor - Altima
Fig. 3
k (Coupe Only)
e
6
d
g (Sedan / HEV Only)
f (Sedan / HEV Only)
a
h (Sedan / HEV Only)
b
c
j
i
Metal Clip
Pawl
Clip C101
Vehicle Front
Page 5 of 25
Rev. 11-24-08
In-mirror RearView Monitor - Altima
5) Remove the following interior parts as shown in Fig. 4 (Refer to vehicle service manual)
a) Trunk Floor Carpet (Coupe Only)
b) Trunk Floor Carpet (Sedan / HEV Only)
c) Spare Tire Cover
d) LH Trunk Floor Board
e) Trunk Lid Finisher (Coupe Only)
f) Trunk Lid Finisher (Sedan / HEV Only)
g) Trunk Rear Finisher (Coupe Only)
h) Trunk Rear Finisher (Sedan / HEV Only)
i) LH Trunk Side Finisher (Coupe Only)
j) LH Trunk Side Finisher (Sedan / HEV Only)
k) Airduct (HEV Only)
l) LH Trunk Grommet (Coupe Only)
Fig. 4
e (Coupe Only)
f (Sedan / HEV Only)
g (Coupe Only)
h (Sedan / HEV Only)
b (Sedan / HEV Only)
7
j (Sedan / HEV Only)
c
d
10mm Bolt
l (Coupe Only)
k (HEV Only)
i (Coupe Only)
Metal Clip
a (Coupe Only)
Pawl
Clip C101
Vehicle Front
Page 6 of 25
Rev. 11-24-08
In-mirror RearView Monitor - Altima
Fig. 5
m)Remove 3 8mm license lamp finisher nuts. (Fig. 5)
n) Remove license lamp finisher by pulling toward
the rear, then disconnect the trunk request
switch connector. (Fig. 5)
Fig. 6
6) Install EC Mirror
a) Plug the harness connector into the back of the
EC mirror.
b) Slide the EC mirror base over the button on the
windshield. (Fig. 6)
c) Using a T-20 Torx head driver, tighten the
screw on the mirror mount to 1.5 - 2.0 Nm
(1.3 ft - lbs). (Fig. 6)
1.5 - 2.0 Nm
Fig. 7
d) Wrap 1 piece of foam tape around harness and
using panel removal tool, tuck between headliner and roof above EC mirror. (Fig. 7)
Foam Tape
Fig. 8
e) Route the harness into the groove of the wire
cover and attach to the mirror mount. (Fig. 8)
f) Slide the forks on top of the wire cover into the
headliner. (Fig. 8)
Page 7 of 25
Rev. 11-24-08
In-mirror RearView Monitor - Altima
Fig. 9
g) Wrap 1 piece of foam tape around harness at
center of sun visor and where the headliner
bends towards driver-side door. (Fig. 9)
Foam Tape
h) Using panel removal tool, tuck the wire harness
between the headliner and roof. (Fig. 9)
Fig. 10
Wire Tie
i) Route harness down driver-side A-pillar and
secure to existing vehicle harness with 3 wire
ties and to A-pillar body with 1 piece of foam
tape. (Fig. 10)
Foam Tape
!
CAUTION
• Do not tie wrap harness to clear drain tube.
Fig. 11
Foam Tape
j) Wrap 2 pieces of foam tape around harness
and tuck between vehicle body and center
dash. (Fig. 11)
Page 8 of 25
Rev. 11-24-08
In-mirror RearView Monitor - Altima
Fig. 12
k) Install ring terminal from harness over ground
bolt (located behind padding in driver-side footwell area) and reinstall. (Fig. 12)
Ground Ring
l) Pull harness ground wire out from behind padding (ensure wire does not block fastener openings). (Fig. 12)
Fig. 13
m)Route power wire (Red Wire) through the center dash and into the driver-side junction box.
(Fig. 13)
Foam Tape
Fig. 14
n) Secure power wire with 1 piece of foam tape to
center dash frame. (Fig. 14)
Page 9 of 25
Rev. 11-24-08
In-mirror RearView Monitor - Altima
7) Secure gray end of the wire tap to Violet / Yellow
Wire. (Fig. 15)
a) See steps 8 - 12 for wire tap installation instructions.
NS06MW-M2-X
White / Blue
MM01
MH02 MH01
MM02
MH06 MH05 MH04 MH03
Violet / Yellow
Fig. 15
Green / Yellow
White / Blue
10- Pin Connector
NS06MW-M2-X
Green / Yellow
Fig. 16
b)
a)
Violet / Yellow
8) Tap Vehicle Wire. (Fig. 16)
a) Remove cap (slot side) from tap body.
b) Slide the cap around vehicle wire.
c) Tighten the tap TIGHT with finger pressure.
c)
NOTE:
Do not re-use the tap for subsequent re-installation.
Fig. 17
9) Inspect the Tap to Ensure Correct Installation.
(Fig. 17)
NOTE:
Avoid putting pressure on the vehicle wire and
tap for the rest of the installation.
i Straight and evenly spaced all the way around
ii. Tight and minimize gap (wire jacket should be crushed)
Page 10 of 25
Rev. 11-24-08
In-mirror RearView Monitor - Altima
Fig. 18
c) Insert wire to here
c)
a)
d)
f) Tighten
Fig. 19
10)Tap Accessory Wire. (Fig. 18)
a) Remove tap (non-pierce) side from tap.
b) Remove the protective stub.
c) Insert wire through the non-pierce side opening.
d) Spread the individual strands into fan shape.
e) Insert wire into the tap body and ensure that it
is all the way in.
f) Tighten the tap TIGHT with finger pressure. 11)Confirm the Tapped Accessory Wire (Fig. 19)
a) Inspect the tap to ensure correct installation.
b) Test the signal to ensure that it is working
properly.
NOTE:
Avoid putting pressure on the vehicle wire, tap,
and accessory wire for the rest of the installation.
i. Straight and evenly spaced all around
ii. Tight and no gap
iii. Test the signal
Fig. 20
b)
a)
Existing
Harness
Accessory
Harness
12)Secure the Tap (Fig. 20)
a) Secure the tapped wire on the non-pierce side
to the body of the posi-tap with electrical tape
(2 revolutions).
b) Secure the body to harness where vehicle wire
is being tapped with electrical tape ( 2 revolutions).
Fig. 21
c) Bundle excess harness ground wire and secure
to existing vehicle harness with 1 wire tie.
(Fig. 21)
Wire Tie
13)Route Harness to Rear Gate
a) Secure harness in footwell area to existing
vehicle harness with 1 wire tie. (Fig. 21)
Page 11 of 25
Rev. 11-24-08
In-mirror RearView Monitor - Altima
Wire Tie
Fig. 22
Steps b - h are for Altima Sedan / HEV Only - Coupe
vehicle’s skip to step i, page 14
b) Secure harness to existing vehicle harness with
4 wire ties. (Fig. 22)
Yellow
Connector
Fig. 23
c) Secure harness to existing vehicle harness with
3 wire ties. (Fig. 23)
Wire Tie
Wire Tie
!
CAUTION
• Harness must be routed behind (outboard) and below safety (yellow) connector.
• Harness must have wire tie placed right below yellow connector.
Fig. 24
Wire Tie
d) Secure harness to existing vehicle harness with
2 wire ties. (Fig. 24)
Page 12 of 25
Rev. 11-24-08
In-mirror RearView Monitor - Altima
Fig. 25
Wire Tie
e) Secure harness to existing vehicle harness with
1 wire tie. (Fig. 25)
Fig. 26
f) Continue routing harness from passenger compartment into trunk area, securing to existing
vehicle harness with 1 wire tie. (Fig. 26)
Wire Tie
Fig. 27
g) Route harness along side of existing vehicle
harness and secure with 7 wire ties. (Fig. 27)
Wire Tie
Fig. 28
h) Continue routing harness into trunk lid compartment ensuring harness is routed along side
existing vehicle harness. (Fig. 28)
For Altima Sedan / HEV vehicle’s skip to step 14,
page 16.
Harness
Page 13 of 25
Rev. 11-24-08
In-mirror RearView Monitor - Altima
Fig. 29
Wire Tie
i) Secure harness to existing vehicle harness with
6 wire ties. (Fig. 29)
Fig. 30
Wire Tie
j) Secure harness to existing vehicle harness with
4 wire ties. (Fig. 30)
Fig. 31
k) Continue routing harness from passenger compartment into trunk area, securing to existing
vehicle harness with 2 wire ties. (Fig. 31)
Wire Tie
Fig. 32
l) Route harness along side of existing vehicle
harness and secure with 6 wire ties. (Fig. 32)
Wire Tie
Page 14 of 25
Rev. 11-24-08
In-mirror RearView Monitor - Altima
Fish Wire
Fig. 33
m)Starting from the trunk lid side, route fish wire
(or equivalent) through rear grommet into passenger compartment. (Fig. 33)
Fig. 34
n) Wrap fish wire around end of tubing of harness. (Fig. 34)
Fig. 35
Harness
o) Pull harness from passenger compartment
through rubber grommet, through trunk lid
access hole and into trunk compartment.
(Fig. 35)
Fig. 36
p) Continue routing harness along side of existing
vehicle harness and into the trunk compartment. (Fig. 36)
Harness
Page 15 of 25
Rev. 11-24-08
In-mirror RearView Monitor - Altima
14)Secure gray end of the wire tap to Pink / Black
Wire. (Fig. 37)
a) See steps 8 - 12 on pages 10 and 11 for wire
tap installation instructions.
Fig. 37
B30 - Rear Combination Lamp LH
Black / Red
Green / Yellow
Pink / Black
3 4
5 6
1
2
B30 - Rear Combination Lamp LH
Black / Red
Pink / Black
Fig. 38
15)Camera Installation
a) Cut out vehicle specific template (on a bench
away from the vehicle) located on last page of
instructions and attach to license lamp finisher. b) Using a drill and 3/16” drill bit, drill out all 6
locating holes. (Fig. 38)
Electrical Tape
Fig. 39
c) Attach 4 pieces of masking tape perpendicular
and parallel to license lamp finisher. Ensure
tape is placed to the outsides of the inner drill
holes. (Fig. 39)
Page 16 of 25
Rev. 11-24-08
In-mirror RearView Monitor - Altima
Fig. 40
Cuts
Cuts
d) Using a dremel tool and a 13/16” rotary cut
off wheel, create a cut at the upper and lower
sections of the taped off portion parallel to the
license lamp finisher. (Fig. 40)
e) Remove masking tape from finisher. Camera Label
M3 x 6mm
Phillip’s Screw
Fig. 41
xx x
f) Align camera and bracket using the camera
label and screw holes as reference guides
(Fig. 41)
Flat Edge
Camera Label
g) Attach camera onto camera bracket and secure
using 2 M3 x 6mm Phillip’s screws as shown.
(Fig. 39)
Fig. 42
h) Insert top portion of camera bracket into top
portion of bracket grommet as shown. (Fig. 42)
xxx-xxxx
i) Pull back lower left and right hand side of grommet and insert camera bracket. (Fig. 42)
Flat Edge
Camera Front
Fig. 43
Rear of Vehicle
j) Insert camera with bracket into previously performed cut out as shown. (Fig. 43)
Flat Edge
Page 17 of 25
Rev. 11-24-08
In-mirror RearView Monitor - Altima
Locating Hole
Fig. 44
k) Using fingers or plastic pry tool, fold back center on right side of grommet in order to expose
the hole in the bracket and finisher as shown. (Fig. 44)
l) Insert 1 6/32” x 3/8” Phillip’s screw into locating
hole as shown. (Fig. 44)
Phillip’s Screw
Speed Nuts
m)Repeat procedure on right side of grommet.
Fig. 45
n) Place 2 speed nuts onto the back of the 2 6/32”
x 3/8” Phillip’s screws and securely tighten
down using a Phillip’s screwdriver as shown.
(Fig. 45)
Fig. 46
o) Cut 2 pieces of foam tape in half.
p) Secure camera harness to license lamp finisher
with 3 half pieces of foam tape in locations
shown. (Fig. 46)
1/2 Foam
Tape
Fig. 47
Slit in Grommet
8.5mm
q) Using side cutters, cut a slit in the request
switch harness grommet approximately 8.5 mm
in length. Once complete, cut a small triangular
portion (approximately 4.5 mm in diameter) out
of the grommet to allow for the camera harness. (Fig. 47)
Page 18 of 25
Rev. 11-24-08
In-mirror RearView Monitor - Altima
Fig. 48
Butyl Gum
Slit in
Grommet
r) Wrap a piece of butyl gum around camera harness approximately 11 inches from camera end
(measurement does not include the length of
the camera itself). (Fig. 48)
11 in.
!
CAUTION
• Apply butyl gum to prevent potential leaks.
Butyl Gum
Fig. 49
s) Insert camera harness with butyl gum into
cut-out of grommet. Ensure butyl gum is
spread evenly over grommet to ensure sealing.
(Fig. 49)
Wire Tie
Fig. 50
t) Secure camera harness to existing trunk request switch harness with 1 wire tie. (Fig. 50)
Page 19 of 25
Rev. 11-24-08
In-mirror RearView Monitor - Altima
Fig. 51
u) Re-install license lamp finisher and reconnect
the trunk request switch connector. (Fig. 51)
Fig. 52
v) Remove black electrical tape and tubing from
harness end.
w) Route camera harness connector to video
cable connector and connect. (Fig. 52)
Steps x - aa are for Altima Sedan / HEV Only - Coupe
vehicle’s skip to step ab.
Fig. 53
x) Secure harness to existing vehicle harness with
6 wire ties. (Fig. 53)
Wire Tie
Fig. 54
Wire Tie
y) Route harness behind existing vehicle harness
and secure with 6 wire ties. (Fig. 54)
Page 20 of 25
Rev. 11-24-08
In-mirror RearView Monitor - Altima
Reverse Wire
Fig. 55
z) Secure harness and reverse wire to existing
vehicle harness with 5 wire ties. (Fig. 55)
Wire Tie
Passenger
Compartment
Back Quarter
Panel
Fig. 56
Wire Tie
aa)Bundle excess harness and secure to existing
vehicle harness with 2 wire ties. (Fig. 56)
For Altima Sedan / HEV vehicle’s skip to step 16
Operation Check, page 22.
Excess Harness
Back Quarter
Panel
Passenger
Compartment
Fig. 57
ab)Secure harness to existing vehicle harness
with 5 wire ties. (Fig. 57)
Wire Tie
Fig. 58
ac)Secure harness to existing vehicle harness with
3 wire ties. (Fig. 58)
Wire Tie
Page 21 of 25
Rev. 11-24-08
In-mirror RearView Monitor - Altima
Foam Tape
Excess Harness
Fig. 59
ad)Secure reverse wire in trunk area to vehicle
body with 1 piece of foam tape. (Fig. 59)
ae)Bundle excess reverse wire and secure to existing vehicle harness with 1 wire tie. (Fig. 59)
af)Bundle excess harness and secure to existing
vehicle harness with 3 wire ties. (Fig. 59)
Wire Tie
Fig. 60
Fig. 61
IM
E
AG
16)Operation Check (Fig. 60)
a) Reconnect the vehicle’s negative battery cable.
b) Tighten negative battery terminal nut to 4.1 Nm.
c) Turn the ignition switch to ON.
d) Ensure vehicle is in a fairly well lit area.
e) Check to see that the green LED is illuminated.
If it is not, press the “
“ button to turn it on.
f) Cover the forward-looking photocell (located
on the back of the mirror) with a dark cloth or
towel. After a few seconds, the mirror should
begin to darken. Timing will vary with ambient
light levels and a flashlight may be shined on
the rearward photocell if needed, to accelerate
effect.
g) Remove the cover from the forward-looking
photocell and the mirror will begin to clear.
h) With your foot on the brake pedal, move the
gear selector lever into reverse.
i) A clear image should display in the left hand
side of the mirror. (Fig. 61)
j) Move the gear selector lever back into park.
The image should now disappear.
17)Re-Installation of Removed Parts
a) Re-install all removed vehicle parts referring to the service manual for the vehicle.
!
CAUTION
• Use caution when re-installing interior components to avoid damage, scratches, or breaking of mounting
clips. Refer to the vehicle specific service manual for more information.
b) Clean interior of vehicle.
Posi-Tap™ is protected by patent # 5,228,875 5,695,369 5,868,589 6,692,313 Jap 2881414 Aus 708700
Tia 103534 Can 2204826 Mex 200626 Korea 477279 China Z197105562.9 & others pending.
Page 22 of 25
Rev. 11-24-08
In-mirror RearView Monitor - Altima
18)Trouble Shooting Guide
Before attempting to trouble-shoot EC mirror Rear Camera Display function, ensure the following:
1. Mirror is manufactured by Gentex Corporation (the letters GNTX will be etched onto the back
of the mirror and the LCD window will be in the mirror glass).
2. EC mirror harness must be fully plugged into EC mirror.
3. Parking brake engaged.
4. Vehicle ignition must be in the "ON" position and vehicle in Reverse (key on / engine off).
5. Camera lens must be clean and unobstructed.
6. Dim ambient light will cause a dim screen, a well lit area will give you the brightest results.
START
Is there live
video feed
visible on the
screen?
Does mirror
turn off after
taken out of R?
YES
NO
Is the car
"ON" and in
Reverse?
YES
NO
Turn key to "ON"
and put into
reverse.
NO
NO
Does the mirror
dim while in
reverse?
YES
NO
YES
ENSURE:
1. EC harness power
wire is securely plugged
into wire splice connector
on vehicle's correct 12V
IGN, and 12V reverse
signal supply wires.
YES
Is mirror receiving
12V from ignition, 12V
reverse signal, and
ground?
Are there any
"dead" pixels
(solid color dots
or lines) in the
screen?
2. EC harness ground
wire is securely attached
to vehicle grounding
point.
YES
NO
Does mirror
turn off after
taken out of R?
ENSURE:
1. EC harness power
wire is securely plugged
into wire splice connector
on vehicle's correct 12V
IGN, and 12V reverse
signal supply wires.
Mirror is functioning
properly.
YES
NO
2. EC harness ground
wire is securely attached
to vehicle grounding
point.
Replace Mirror
Part 999Q6 VV020
Harness (Mirror Side)
Is mirror receiving
12V from ignition,
12V reverse signal,
and ground?
NO
9
1
YES
NO
Is mirror
sending 6V
and ground to
camera?
YES
Replace Mirror
Part 999Q6 VV020
NO
8
16
Is camera
receiving
6V and
ground?
Pin
Wire Color
Function
4
Lt. Green
Camera Power
6
Red
Video +
7
Black
Video -
8
Black
Mirror Ground
9
Green
Reverse Signal
10
White
Camera Ground
13
Red
Mirror Ignition
YES
Order new wire harness kit
999Q6 VV060SP
Does the image
appear grainy
or staticy
YES
Harness (Camera Side)
5
NO
Replace Mirror
Part 999Q6 VV020
Order new wire harness kit and
camera
999Q6 VV060SP
and
999Q6 VV030
1
Page 23 of 25
Pin
Wire Color
Function
1
Green
Camera Power
2
White
Camera Ground
3
Yellow
Drain
4
Black
Video -
5
Red
Video +
Rev. 11-24-08
In-mirror RearView Monitor - Altima
9. Post Installation Check Sheet
Inspect the vehicle interior and exterior for damage.
Confirm proper operation of vehicle systems.
Reset radio presets to the recorded settings.
If equipped, verify proper sunroof operation and perform the reset procedure if necessary.
Refer to Service Manual requirements.
Place the User Guide in the glove box.
Check the trim for proper flush fit after re-installing the interior components. Verify the camera is operating properly
There should be no objects from vehicle (i.e. grommet, license plate etc.) interfering with
the camera view
Camera should meet the below performance requirements
The grey area indicated
must be included in the
display
Vehicle width Both
sides 200 mm
300 mm
5,000 mm
Bold lines indicate the
actual field of vision.
A
B
A: 300 mm max.
B: 5,000 mm min.
Page 24 of 25
Rev. 11-24-08
Page 25 of 25
29 mm
(1.14 in)
34 mm
(1.34 in)
34 mm
(1.34 in)
•• Use a 3/16” drill bit to drill out all 6 “ “ locating holes.
•• Cut out the correct template needed for installation.
•• Before cutting out the appropriate template, measure the square portion of the template to ensure accuracy.
Altima Sedan
Altima Coupe
29 mm
(1.14 in)
In-mirror RearView Monitor - Altima
Rev. 11-24-08