parextherm and parexdirect acrylic dpr render systems standard

Transcription

parextherm and parexdirect acrylic dpr render systems standard
Part 3_Updated_Layout 1 02/10/2010 17:41 Page 95
PAREXTHERM AND PAREXDIRECT
ACRYLIC DPR RENDER SYSTEMS
STANDARD COLOUR CHART
THE CHOICE OF CONFIDENCE
SOLAR ABSORPTION
Parex Standard Colours are the forty most popular colours
chosen by designers. Explore the clarity achieved through the
highest quality pigments available.
Please note dark colours with a solar absorption coefficient over
0.7 are more sensitive to colour alteration, efflorescence, lime
bloom and to climatic constraints. Ensure that humidity and
temperature conditions are taken into account when they are used.
If a dark colour is required we strongly recommend you use Parex
600 CLEAR SEALER OR 610 MATT CLEAR SEALER to provide
additional protection to your DPR finish from harmful UV light.
COLOUR MATCHING
Due to our unique tinting process we are able to offer the designer
an infinite choice of colour options. We are able to match any colour
from the BS, RAL, Dulux and other colour systems. We currently
have over 30,000 colour formulations and we are able to produce
these or new colours within 2 - 3 days subject to manufacturing
capacity.
DURABILITY
Our unique formulation uses 100% acrylic polymers (Do not get
confused with a small percentage approx 1 - 2% of silicone added.
Silicone added into the acrylic finish provides no discernable
benefit and can cause chalking of the surface over time). The
acrylic polymeric bonding in our DPR acrylic finishes form a tough
surface yet remains pliable and is vapour permeable preventing
weather penetration but allowing the building to breath.
Parex 100% acrylic finishes stay fresher longer, resisting fading,
chalking, and yellowing. In cyclical weathering tests the finishes
resist colour wash, peel adhesion and wet abrasion using a stiff
brush being scrubbed back and forth.
ATTENTION
Please note that colours printed on this chart may be subject to
variations when reproduced on paper. To obtain a 1 litre colour
sample pot or an individual 200 x 200 mm sample please contact
Parex. Final colour approval is the responsibility of the customer
and should be made after reviewing an actual sample.
PLEASE NOTE
The shade of the same colour may also differ dependent upon the
finishing aspect; e.g. The colour of a Sand Fine finish adjacent to a
Swirl Coarse finish in the same colour may appear to look different
when viewed next to each other. The colour chart below has been
sorted according to colour and reference number:
93
Part 3_Updated_Layout 1 02/10/2010 17:41 Page 96
DPR FINISHES STANDARD
COLOUR CHART
COLOURS
SNOWBALL
10400(92)
MARBLE WHITE
10401(90)
ALMOND
10407(73)
OCHRE
10433(69)
INDIAN SUMMER
10434(66)
ALUMINIUM
10445(72)
CLEAR LINEN
10431(81
CASHMERE
10411(49)
BAMBOO
10425(66)
LIMESTONE
10402(71)
SLATE
10404(50)
GREY MIST
10443(65)
STEEL GRAY
10420(58)
MOONSTONE
10446(74)
CLASSIC CREAM
10421(44)
CLAY POWDER
10452(35)
MALTED BROWN
10424(43)
TUNDRA
10409(55)
VANILLA CREAM
10451(68)
IVORY
10444(86)
94
The numbers in the brackets () indicate reflective value. The higher the number, the less UV light the colour absorbs.
Due to printing variations the colours indicated on this colour chart are offered as guidance only and should not be relied upon as a true representation of the actual colour of the finish. Colour will vary
depending on the type of finish selected. Application by machine spray or texturing will increase the depth of the colour. Variation in colour due to weather, site conditions and method of application should be
expected. For colour verification, request an actual sample in the colour and texture prior to ordering materials. Apply a sample of the finish to be used on the actual substrate before proceeding with the
application. Due to the variation in applicator techniques, Parex Ltd is not responsible for the appearance or colour correctness of the applied finish. Colour, texture and finish must be verified and approved
by owner prior to application.
The information provided in this document results from our knowledge of the products and our experience. On-site results may vary, in particular
according to the product application methods adopted. Where application methods not covered by this document are used, customers must request
specific additional information and/or carry out a representative test before using the products. The above-mentioned information in no way
constitutes a warranty relative to the use of the products. Our general terms and conditions of sale shall prevail, in any event, on the information
provided in this document. Prior to application, customers and users are requested to check that they have the latest version of this document.
Part 3_Updated_Layout 1 02/10/2010 17:41 Page 97
This colour chart is a standard range of available colours. Parex are able to offer a bespoke service of colours to match BS, RAL,
Dulux or other paint system colours. With a colour choice of over 30,000 formulations, colour choice is never an issue. If you need
to colour match, send us a sample and we can!
PEPPER
10450(36)
MOSS
10447(43)
CANYON DAWN
10449(61)
KHAKI
10414(60)
BEIGE DUNE
10448(73)
BRUSHWOOD
10423(55)
CHAMOIS
10441(42)
SANTA FE ROSE
10436(61)
95
ORIENTAL GOLD
10438(44)
EVENING SHADOW
10440(43)
WARM SAND
10432(62)
PALE WHITE
10430(80)
TRIANON VELVET
10435(77)
SMOKEY MAUVE
10426(55)
APRICOT
10427(64)
PEWTER
10403(63)
LAVENDER
10439(52)
SPICE TAN
10415(52)
PEACHTREE FROST
10437(80)
SPICY SUNSET
10442(39)
The numbers in the brackets () indicate reflective value. The higher the number, the less UV light the colour absorbs.
Due to printing variations the colours indicated on this colour chart are offered as guidance only and should not be relied upon as a true representation of the actual colour of the finish. Colour will vary
depending on the type of finish selected. Application by machine spray or texturing will increase the depth of the colour. Variation in colour due to weather, site conditions and method of application should be
expected. For colour verification, request an actual sample in the colour and texture prior to ordering materials. Apply a sample of the finish to be used on the actual substrate before proceeding with the
application. Due to the variation in applicator techniques, Parex Ltd is not responsible for the appearance or colour correctness of the applied finish. Colour, texture and finish must be verified and approved by
owner prior to application.