CSOR206

CSOR206
(Option AA)
CSOR206
CSOR206
(Option AB)
1Y-16
1Y-16
Distribution Matrix
Applications
Sports Bars
Board Rooms
• Matrix sizes from 4x4 up to 16x16
per signal type
Home Theater Systems
Distance Learning
Broadcast Environments
• Multiple I/O board combinations
Security Systems
Video Arraignment Systems
• 400 MHz Ultra-Wideband performance
CSOR206
GENERAL
AC Power:
100 - 240 VAC
Maximum Power Consumption: 30 Watts per enclosure
Operational Temperature:
32º to 110º F (0º to 43º C)
Humidity:
0 to 90% non-condensing
Dimensions:
17.00 in (43.18 cm) depth
17.00 in (43.18 cm) width without mounting ears
19.00 in (48.26 cm) width with mounting ears
3.50 in (8.89 cm) height (2 r.u.)
Weight:
17 lbs (7.73 kg) per enclosure
Approvals:
CE, ETL (conforms to UL 1419)
AUDIO
Throughput:
Frequency Response:
Total Harmonic
Distortion + Noise:
Crosstalk:
Signal to Noise Ratio (SNR):
Input:
Maximum Level:
< ± 0.1 dB (20 Hz to 20 kHz)
< 0.01% (20 Hz to 20 kHz, Vin = -3.3 dBu to 13.2 dBu)
< -95 dB (1 kHz, Vin = ± 24 V Balanced)
-103 dB (20 Hz to 20 kHz, Vin = 13.2 dBu)
Common Mode: 22.7 dBu
Differential: 28.2 dBu
18 kΩ
Balanced or Unbalanced
Impedance:
Type:
Common Mode
Rejection Ratio (CMRR):
Power Supply
Rejection Ratio (PSRR):
Gain Adjustment Range
(optional):
Connector type(s):
-3 dB to +10 dB (Vin = 3 Vp-p)
Disconnectable, 3 Position Screw Terminal
Output:
Maximum Level:
Impedance :
Type:
Gain Adjustment Range:
Connector type(s):
25.96 dBu, Balanced
50 Ω
Balanced or Unbalanced
-3 dB to +10 dB
Disconnectable, 3 Position Screw Terminal
-90 dB typical, -70 dB min. (20 Hz to 20 kHz, Vcm = ± 10 V)
-80 dB typical, -60 dB min. (20 Hz to 20 kHz, Vs = ± 15 V)
Differential Gain:
Differential Phase:
Crosstalk
(adjacent channel):
Propagation Delay:
Signal to Noise Ratio (SNR):
Input:
Maximum Level:
Impedance:
Gain Adjustment Range
(optional):
Connector type(s):
Output:
Maximum Level:
Impedance:
Gain Adjustment:
Connector type(s):
± 3 dB to 60 MHz or Better
± 1 dB to 30 MHz or Better
0.1% or Better (f = 3.58 MHz)
0.1º or Better (f = 3.58 MHz)
Crosstalk
(adjacent channel):
Propagation Delay:
Output:
Maximum Level:
Impedance:
Gain Adjustment:
Connector type(s):
Enclosures link
for maximum
flexibility
Modular system
with many I/O
board types to
precisely fit
your application
4 slot
(2 r.u.)
±5V
75 Ω or Hi-Z (22 kΩ)
6 slot
(3 r.u.)
-3 dB to +10 dB
BNC
8 slot
(4 r.u.)
±5V
75 Ω
-7.5 dB to +7.5 dB
BNC
ULTRA-WIDEBAND VIDEO
± 3 dB to 200 MHz
or better
± 3 dB to 400 MHz
or better
< -60 dB (f = 5 MHz)
< -60 dB (f = 5 MHz)
< 20 ns (Vin = ± 0.5 V) < 20 ns (Vin = ± 0.5 V)
Signal to Noise Ratio (SNR): < -70 dB
< -70 dB
(Vin = 0.7 V, 100% IRE) (Vin = 0.7 V, 100% IRE)
Input:
Maximum Level:
Impedance:
Gain Adjustment Range
(optional):
Connector type(s):
RS-232 serial
control port
CPU features 64
memory ”presets“
< -40 dB (f = 5 MHz)
< 20 ns (Vin = ± 0.5 V)
< -70 dB (Vin = 0.7 V, 100% IRE)
WIDEBAND VIDEO
Throughput:
Frequency Response:
• Matrix sizes from 4x4 up to 16x16 per signal type
• Ideal for routing: Composite Video (NTSC, PAL,
SECAM), Y/C and S-Video, Component Video, RGB,
RGBS, RGBHV, Mono Audio, Stereo Audio, Serial
Digital, RS-232, RS-422
• Multiple I/O board combinations
• 400 MHz Ultra-Wideband performance
• Switch any input to any or all outputs, or any combination
• Multiple vertical enclosure size options for
precise customization
• Includes APControl, free Windows matrix control and
scheduling software
• X/Y Control Panels support quick disconnect and
single touch status
System Options:
Local and Remote (to 1000 ft.) X/Y Control Panels
Single Bus Controller Keypads
Vertical Interval Switching
Input Gain Control (Audio and Video)
Redundant Power Supply
4-slot, 6-slot, and 8-slot enclosures
CPU expansion slots
for future options
STANDARD VIDEO
Throughput:
Frequency Response:
1Y-16 Distribution
Matrix Specifications
2 4 1 6 C he ne y - S p o ka ne R d. C he ne y, WA 9 9 0 0 4 - 0 3 5 0
509-235-2636
±2V
75 Ω or Hi-Z (22 kΩ)
±2V
75 Ω or Hi-Z (22 kΩ)
-3 dB to +10 dB
BNC
-3 dB to +10 dB
BNC
±2V
75 Ω
-5.5 dB to +6.7 dB
BNC
±2V
75 Ω
-5.5 dB to +6.7 dB
BNC
800-622-0246 (US)
w w w. a u t o p a t c h . c o m
Fax 509-235-2646
e - ma i l : s a l e s @ a u t o p a t c h . c o m
AutoPatch is a division of XN Technologies, Inc.
CSOR206
(Option BA)
VP201s/VP201b LCD Display
CSOR206
(Option CA)
20.1" ThinEdge™ Ultra–Slim Bezel Display
Immerse yourself in the panorama of this big-picture LCD.
Turn your ideas into breathtaking reality with the 20" VP201s and VP201b LARGESCREEN THINEDGE ULTRA-SLIM BEZEL LCD displays. With astounding 176º ultrawide viewing angles, UXGA 1.92 megapixel resolution, ClearMotiv™ broadcast-quality
video technology and native HDTV high-scan 720p compatibility, these displays
boost professional productivity and heighten user enjoyment for video editors,
financial traders, CAD/CAM engineers and power gamers. Ideal for multiple-panel
configurations with height/pivot
adjustments, digital/analog inputs
and USB 2.0 high-speed
connectivity, the VP201s and
VP201b are the infinitely versatile
professional desktop displays
VP201b shown.
Also available in silver (VP201s)
of choice.
Uncompromised features and versatility to have you seeing 20/20.
> ThinEdge
maximizes your productivity
The ultra-slim 0.67" bezel design enhances your visual
experience with clean, minimalist borders around the
active image area. Suitable for tiling and stacking.
> Ideal
for multiple-monitor setups
ThinEdge minimizes bezel gaps between panels for a virtually
continuous viewing area in multiple-panel setups.
> Pivot,
height and wall-mount versatility
VESA® wall-mount interface and detachable base for ergonomic
flexibility with pivot, height, tilt and swivel adjustments.
>
analog/digital inputs and integrated
USB hub expand your connectivity
> Full
ThinEdge design is ideal for multi-panel setups. Four unit
panel-module-only (without base) multi-packs available.
20.1" viewable screen
> 1600x1200
> High
native resolution
brightness and contrast
250-nit brightness (typ) and 400:1 contrast ratio
(typ) for rich images.
> HDTV–720p
> Image
ready
clarity from all directions
XtremeView® performance features ultra-wide 176º
viewing angles horizontally and vertically.
> Integrated
power supply with hard
power switch
Includes one DVI-I (analog or digital capable) and one analog input.
Integrated USB 2.0 high-speed hub enables unlimited connectivity
and ENERGY STAR®
TCO’03 for silver and TCO’99 for black models.
options.
> ClearMotiv
> TCO’03
technology
Ultra-fast 16ms video response enables digital HD broadcast-quality
full-motion video at 62.5 fps.
ThinEdge
VP201s/VP201b LCD Display
CSOR206
Pivot feature saves time
Spend less time scrolling long documents. Simply
rotate your screen from landscape to portrait.
Wide-travel height adjustment
With over 41/4 inches of travel, this LCD fits just right.
LCD PANEL
Type
20.1" color TFT active matrix UXGA LCD
Display Area
16.1" (horizontal) x 12.1" (vertical); 20.1" diagonal
Optimum Resolution 1600x1200
Contrast Ratio
400:1 (typ)
Viewing Angles 176° horizontal, 176° vertical @ CR>10
Response Time
16ms (typ)
Brightness
250 cd/m2 (typ)
Glass Surface
Anti-glare
VIDEO INPUT
Analog
Digital
Frequency
Sync
COMPATIBILITY PC
Mac®*
HDTV
VGA up to 1600x1200 non-interlaced
Power Mac™ G3/G4 up to 1600x1200
480p, 720p
CONNECTOR
Analog
Digital
USB
Power
15-pin mini D-sub
Digital DVI-I
V 2.0 Up stream (B type) x1; Down stream (A type) x4
3-pin plug (CEE22)
POWER
Voltage
Consumption
AC 100–240V (universal), 50–60Hz
70W (typ)
CONTROLS
Basic
OnView®
Power, 1, down, up, 2
Auto image adjust, contrast, brightness, input select (D-sub, DVI-A, DVI-D),
color adjust (9300K, 6500K, 5400K, 5000K, user color), information (H/V
frequency, resolution, model number, serial number, web site), manual
image adjust (H. size, H/V position, fine tune, sharpness, scaling), setup
menu (language, resolution notice, input priority, OSD position, OSD timeout, OSD background, OSD pivot), memory recall
OPERATING
CONDITION
Temperature
Humidity
32–104° F (0–40° C)
10–90% (non-condensing)
DIMENSIONS
(W x H X D)
Physical:
448mm x 480mm x 267mm (with stand)
17.6" x 18.9" x 10.5" (with stand)
448mm x 346mm x 71mm (without stand)
17.6" x 13.6" x 2.8" (without stand)
WEIGHT
Net
Gross
18.7 lb. (8.5 kg) with stand; 11.5 lb. (5.2 kg) without stand
24.7 lb. (11.2 kg) with stand; 15.9 lb. (7.2 kg) without stand
REGULATIONS
UL, cUL, FCC-B, CB, CE, ENERGY STAR®, NOM, TUV/GS, TUV Ergo, (covers
ISO13406-2 and MPR II) TCO’03 (VP201s), TCO’99 (VP201b), NEMKO,
SEMKO, DEMKO, FIMKO, GOST-R, hygienic, SASO, PCBC, VCCI, BSMI, CCC,
PSB, C-TICK, TUV-S
POWER MANAGEMENT
Meets TCO and ENERGY STAR® standards
Hard power switch
Integrated power supply
RGB Analog (75 ohms, 0.7/1.0 Vp-p)
DVI-D (TMDS, 100 ohms, or analog capable)
Fh: 30~92kHz, Fv: 50~85Hz
H/V separated, composite, sync-on-green (TTL)
WARRANTY
1 up / 4 down USB 2.0 hub
specifications
20.1" ThinEdge™ Ultra–Slim Bezel Display
Three-year limited warranty on parts, labor and backlight.
Analog VGA connector
Digital/analog DVI-I connector
ViewSonic Corporation’s QMS & EMS have been registered to
ISO 9001 & ISO 14001, respectively, by the British Standards Institution.
ViewSonic Corporation • 381 Brea Canyon Road, Walnut, CA 91789
Phone (800) 888-8583 or (909) 444-8888 • In Canada (866) 262-1967 • Fax (909) 839-7922 • [email protected] • ViewSonic.com
*Adapter may be required. Analog adapter available from ViewSonic. Specifications subject to change without notice. Selection, offers and programs may vary by country; see your ViewSonic representative for complete details. Corporate names, trademarks stated herein are the property of their respective
companies. Copyright © 2004 ViewSonic Corporation. All rights reserved. [12116-00B-08/04] VP201s-1/VP201b–1
For more product information, visit us on the web at ViewSonic.com
CSOR206
(Option CA)
CSOR206
(Option DA)
CSOR206
(Option DA)
Polycom® Vortex® EF2280
Acoustic echo/noise canceller with automatic
microphone/matrix mixer
Benefits
Industry-leading acoustic echo and noise
cancellation – Ensures the highest possible
audio quality between sites
High-quality audio – 20 kHz bandwidth, 270
ms tail length, more than 10 dB of room gain, and
a convergence rate of over 40 dB per second on
each mic/line channel
Easy to operate – User-programmable delays
on all outputs, up to 32 user-configurable
presets, 16 factory presets, and 256 macros for
flexible control
Interoperable – Cascade up to eight Vortex
EF2280 units for up to 64 mic channels, or link
with Vortex EF2201, EF2210, EF2211 and other
Polycom products
Enjoy clear, understandable conversation in all conferencing applications. The Vortex EF2280 improves audio quality for conferencing, distance
learning, and other installed applications through industry-leading acoustic
echo and noise cancellation.
The Vortex EF2280 automatically mixes your
EF2280 features industry-leading acoustic echo
microphones and other audio, while cancelling
cancellation; a neural network Automatic Gain
acoustic echoes and annoying background noise.
Control (AGC) reacts only to valid speech pat-
It is typically installed at each site in a multisite
terns, bringing voices within desired levels. AGC
network and includes inputs for microphones
controls are user adjustable, as are settings for
and line level, AEC reference, and auxiliaries, as
the five-band parametric EQ offered on all input
well as output destinations. The unit can be pro-
and output channels and output delay controls.
grammed from the front panel, or through
Conference Composer software (included),
The high-quality audio choice for The
which programs the unit via RS-232. The 32
Polycom Office™
user-configurable presets are augmented by 16
With integrated video, voice, data, and Web capa-
factory presets, which are geared for common
bilities, The Polycom Office is the only solution
applications such as boardrooms, courtrooms,
that offers you an easy way to connect, confer-
distance learning, and room combining.
ence, and collaborate any way you want. The
Polycom Office is our commitment to making
A single Vortex EF2280 unit provides automatic
distance communications as natural and interac-
mixing of up to eight microphones plus four aux-
tive as being there. Work faster, smarter, and bet-
iliary audio sources. If more microphones are
ter with the Polycom Vortex EF2280 and The
needed, additional EF2280 or EF2241 units can
Polycom Office.
be linked, up to a total of eight. Number of Open
Microphones (NOM) information can be specified across all channels in the linked units. The
Connect. Any Way You Want.
CSOR206
System Block Diagram and Rear Panel
Output 1
Output 2
Line
Line
Output 3
Line
Output 4
Line
Output 5
Line
Output 6
Line
Output 7
Line
Output 8
Line
Output A
Line
Output B
Line
Output C
Line
Output D
Line
D/A
D/A
D/A
D/A
D/A
D/A
D/A
D/A
D/A
D/A
D/A
D/A
PEQ /
DELAY
PEQ /
DELAY
PEQ /
DELAY
PEQ /
DELAY
PEQ /
DELAY
PEQ /
DELAY
PEQ /
DELAY
PEQ /
DELAY
PEQ /
DELAY
PEQ /
DELAY
PEQ /
DELAY
PEQ /
DELAY
RS-232
Matrixing
ASPI Bus
Control/Status
EN
EN
EN
EN
EN
EN
EN
EN
PEQ
PEQ
PEQ
PEQ
A/D
A/D
A/D
A/D
A/D
A/D
A/D
A/D
A/D
A/D
A/D
A/D
Level
adjust
Level
adjust
Level
adjust
Level
adjust
Level
adjust
Level
adjust
Level
adjust
Level
adjust
Phantom
Phantom
Phantom
Phantom
Phantom
Phantom
Phantom
Phantom
Mic/Line
Mic/Line
Mic/Line
Mic/Line
Mic/Line
Mic/Line
Mic/Line
Mic/Line
Level
adjust
Line
Mic/Line 1 Mic/Line 2 Mic/Line 3 Mic/Line 4 Mic/Line 5 Mic/Line 6 Mic/Line 7 Mic/Line 8
Input A
Level
adjust
Line
Input B
Level
adjust
EF Bus
Level
adjust
Line
Line
Input C
Input D
EN (Echo Canceller, Noise Canceller)
Ungated
Echo
Canceller
Noise
Canceller
On
Off
AGC
On
Off
EC1, EC2, Bus
PEQ
Parameters
Mute
On
Off
Gate
Gated
Parameters
Polycom Vortex EF2280 Technical Specifications
Dimensions
Line Outputs
• 19” (483 mm) W x 9.6” (244 mm) L x 1.75” (45 mm) H
(one rack unit)
Weight
Connectors
Output Impedance
• 50 Ohms (drives 600 Ohms)
RS-232: DB9F
EF Bus In/Out: RJ45
Control /Status: DB25F
Audio: Mini (3.5mm) quick connect terminal blocks
Headroom
• 20 dB, nominal
Noise Cancellation
• 0-15 dB, software selectable
Operating Temperature
• 0 °- 40 °C
Control Inputs
• Contact closure
Status Outputs
• 5 V, 20 mA each
Signal to Noise Ratio
Power
• External supply (provided)
• Input voltage of 110-240 VAC; 47-63 Hz; power
consumption 30 W
Microphone Input
• Line level, 0 dB gain: >85dB
Frequency Response
• 20 Hz - 22 kHz
Acoustic Echo Cancellation Span
• -30 dBu to +0 dBu/ -66 dBu to -33 dBu, nominal;
software selectable
• 270 ms
Total Cancellation
Phantom Power
• >65 dB
• 24 V, software selectable
Convergence Rate
Line Inputs
• -20 dBu to +0 dBu, nominal; software adjustable
www.polycom.com
Input Impedance
• >10 k Ohms
• 4 lbs. (1.8 kg) dry, 5.5 lbs. (2.5 kg) shipping
•
•
•
•
• -20 dBu to +0 dBu, nominal; software adjustable
• 40 dB/second
©2003 Polycom, Inc. All rights reserved.
Polycom, the Polycom logo, and Vortex are registered trademarks and The Polycom
Office is a trademark of Polycom, Inc. in the U.S. and various countries. All other
trademarks are the property of their respective companies. Specifications subject to
change without notice. For Architect's and Engineer's Specifications, please visit
Polycom.com, or contact the Installed Voice Business Group at 1.770.641.4400.
Polycom, Inc.:
4750 Willow Road, Pleasanton, CA 94588 (T) 1.800.POLYCOM (765.9266) for North America only.
For North America, Latin America and Caribbean (T) +1.925.924.6000, (F) +1.925.924.6100
Polycom EMEA:
270 Bath Road, Slough, Berkshire SL1 4DX, (T) +44 (0)1753 723000, (F) +44 (0)1753 723010
Polycom Hong Kong Ltd.:
Polycom Hong Kong Ltd., Rm 1101 MassMutual Tower, 38 Gloucester Road, Wanchai, Hong Kong, (T) +852.2861.3113, (F)+852.2866.8028
Part No. 3726-82280-001 Rev. 03/03
(Option DA)
This symbol is intended to
alert the user to the presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to constitute a risk of
electric shock to persons.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This symbol is
intended to alert the
user to the presence of
important operating
and maintenance (servicing) instructions in the literature accompanying
the appliance.
IMPORTANT! FOR YOUR PROTECTION, PLEASE READ THE FOLLOWING:
WATER AND MOISTURE: Appliance should not be used near water (near a bathtub, washbowl,
kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc). Care should be taken
so that objects do not fall and liquids are not spilled into the enclosure through openings.
POWER SOURCES: The product should be connected to a power supply only of the type described
in the operating instructions or as marked on the appliance.
GROUNDING OR POLARIZATION: Precautions should be taken so that the grounding or polarization is not defeated.
POWER CORD PROTECTION: Power supply cords should be routed so that they are not likely
to be walked on or pinched by items placed upon or against them, paying particular attention
to cords at plugs, convenience receptacles, and the point where they exit from the appliance.
SERVICING: The user should not attempt to service the appliance beyond that described in the
operating instructions. All other servicing should be referred to qualified service personnel.
FUSING: If your unit is equipped with a fuse receptacle, replace only with the same type fuse.
Refer to replacement text on the unit for correct fuse type.
SAFETY INSTRUCTIONS (EUROPEAN)
The conductors in the AC power cord are colored in accordance with the following code.
GREEN & YELLOW—Earth
BLUE—Neutral
BROWN—Live
U.K. MAIN PLUG WARNING: A molded main plug that has been cut off from the cord is
unsafe. NEVER UNDER ANY CIRCUMSTANCES SHOULD YOU INSERT A DAMAGED
OR CUT MAIN PLUG INTO A POWER SOCKET.
Your Carvin product is guaranteed against failure for ONE YEAR. Carvin will service and supply all
parts at no charge to the customer providing the unit is under warranty. Shipping costs are the responsibility of the customer. CARVIN DOES NOT PAY FOR PARTS OR SERVICING OTHER THAN OUR
OWN. A COPY OF THE ORIGINAL INVOICE IS REQUIRED TO VERIFY YOUR WARRANTY. Carvin
assumes no responsibility for horn drivers or speakers damaged by this unit. This warranty does
not cover, and no liability is assumed, for damage due to: natural disasters, accidents, abuse, loss
of parts, lack of reasonable care, incorrect use, or failure to follow instructions. This warranty is in
lieu of all other warranties, expressed or implied. No representative or person is authorized to represent or assume for Carvin any liability in connection with the sale or servicing of Carvin products.
CARVIN SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
When RETURNING merchandise to the factory, you may call for a return authorization number.
Describe in writing each problem. If your unit is out of warranty, you will be charged the current
FLAT RATE for parts and labor to bring your unit up to factory specifications.
HELP SECTION
1) WILL NOT TURN ON
Check the power to the unit. Check for tripped circuit breakers, unplugged extension cords or
power-strip switches that may be turned off. Check the fuse. If a dark brownish color or no wire
can be seen within the glass fuse, then replace. The unit may be perfectly fine but occasionally
the fuse may blow because of high AC voltage surges. After the fuse has been replaced with the
proper value and if the fuse fails again, the product will require servicing (be sure to use a slow
blow fuse if required). Check your input and speaker output cables.
2) MAINTAINING YOUR EQUIPMENT
Avoid spilling liquids or allowing any other foreign matter inside the unit. The panel of your unit can
be wiped from time to time with a dry or slightly damp cloth in order to remove dust and bring back
the new look. As with all pro gear, avoid prolonged use in caustic environments (salt air). When
used in such an environment, be sure the amplifier is adequately protected by rack, covers, etc..
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL! THIS UNIT CONRISK OF ELECTRIC SHOCK TAINS HIGH VOLTAGE INSIDE!
CAUTION
REPLACEMENT PARTS LIST FOR DCM AMPS
DCM150
21-50311
REV A
2 EACH
JACK PHONO MONO PCB MOUNT
58-10035
1 EACH
#QTY
DESCRIPTION
03-00450
1 EACH
INSLTR 9.125x1.5x.01" SGL ADHV
21-51545
2 EACH
2 EACH
58-10045
R122, R13, R222, R20, R21
R100, R101, R102, R103,
2 EACH
BINDING POST RED/BLK EXT LEGS
03-10625
4 EACH
STANDOFF NYLON #10X .625X .375
03-15010
2 EACH
TOROID PAD 4.75" OD X 2" ID X0
03-18190
3 EACH
CABLE TIE 4"LX .10"W 7/8 BNDLE
03-19810
4 EACH
FOOT PVC BLK SQ"=.810 HGT=.300
03-49550
1 INCH
TAPE W/ADHSVE 3M 80mil x 1.0"
05-48025
1 EACH
SPADE CONNECT 18AWG BLK 254MM
05-48522
2 EACH
SPADE CONNECT 18AWG GRN 228MM
05-68415
1 EACH
CABLE RIBBON 24A 8P/ 6" W/HDR
05-60420
1 EACH
CABLE RIBBON 24A 10P/ 8" W/HDR
05-64435
1 EACH
CABLE RIBBON 24A 4P/14" W/HDR
06-09252
2 EACH
NUT FOR POT 71-09252C
06-10045
6 EACH
SMS PFH #6X .375 TYPE AB BLACK
06-10061
2 EACH
SMS PPH #6 X .375 TYPE A BLACK
06-10070
4 EACH
MS PPH 6-32X .500 BLACK
06-10080
4 EACH
MS PPH 6-32X .750 BLACK
06-10100
4 EACH
MS PPH 8-32X .375 BLACK
06-10193
1 EACH
MS CTH #1/4-20X 1.250 BOLT BLK
06-40070
2 EACH
TERMINAL .25"TAB/.156"LUG/.032
06-50035
8 EACH
NUT KEP #6-32
06-50040
4 EACH
NUT KEP #8-32 BLACK ZINC
06-50051
4 EACH
NUT KEP #10-32
06-50061
1 EACH
NUT HEX #1/4-20 ZINC W/NYLN IN
07-09012
2 EACH
KNOB RECESSED MED 25.0mm BLACK
C103, C104, C107, C11, C112,
10-01501E
1 EACH
FRONT PANEL DCM150
C116, C12, C120, C203, C204,
10-82005
1 EACH
LID DCM/HT POWER AMPS
C207, C212, C216, C220, C7, C8
10-01509G
1 EACH
CHASSIS DCM150
10-15045
1 EACH
PLATE TOROID 4.5" DIA 14A GALV
12-01520A
1 EACH
HEATSINK DCM150/PB200
15-01513
1 EACH
XFORMR 120V HT150
25-31350
1 EACH
SWITCH DPST ROCKER BLACK POWER
76-00001
1 EACH
WARRANTY CARD "CARVIN"
76-00150
1 EACH
MANUAL DCM150
77-01509B
1 EACH
LABEL REAR DCM150
23-11008
2 EACH
2 EACH
R200, R201, R202, R203
FUSEHOLDER CLIPS 3AG VERT MTG
58-10055
F1
23-11004
7 EACH
2 EACH
R108, R208, R114, R214, R125,
H1A, H1B
R225, R138
CONNECT HEADER 8 PIN STRAIGHT
58-10065
2 EACH
CONNECT HEADER 10 PIN STRAIGHT
3 EACH
SWITCH DPDT PUSH PC MTG LOCKNG
58-15035
2 EACH
1 EACH
SWITCH 4PDT PUSH PC MTG LOCKNG
58-15045
2 EACH
1 EACH
58-15055
4 EACH
49-10312
6 EACH
9 EACH
PCB CARD MAIN HT150 PWR AMP
49-10451
2 EACH
49-22035
16 EACH
CAP ELEC 2,200 MFD 35V 20%
49-25152
2 EACH
49-33212
2 EACH
49-33312
2 EACH
49-39052
6 EACH
58-22025
2 EACH
80-01528
58-22035
11 EACH
R15, R218, R219, R226, R233,
R239
58-22045
3 EACH
58-22055
2 EACH
SMT CAP 22uF 35v ELECTROLITIC
58-27025
2 EACH
58-33025
1 EACH
6 EACH
STANDOFF LED .925 x .215 T1
05-22102
4 INCH
POLYOLEFIN SHRINK TUBING 1/16"
06-40050
1 EACH
6 EACH
7 EACH
58-33035
1 EACH
58-33045
2 EACH
0.033UF SMT 10% FILM 0805 50V
58-36055
1 EACH
4 EACH
58-00035
4 EACH
TERMINAL 90dg MALE PC MTG .250
QC1, QC2, QC3, QC4, QC5, QC6
07-01603
4 EACH
KNOB "6L" 6x6x17.4mm GREY CAP
21-31100
1 EACH
RECEPTACLE AC W/FAST-ON CHASS
58-39035
1 EACH
58-47025
1 EACH
PL1
5 EACH
2 EACH
82PF SMT 5% CERAMIC 0805
58-47035
2 EACH
60-55500
4 EACH TRANS 2N5550 HV NPN 250V
T0-92 Q5, Q6, Q17, Q27
60-75200
4 EACH
58-47045
17 EACH
60-75320
3 EACH
60-75330
2 EACH
60-75340
1 EACH
60-78120-1
1 EACH
EGULATOR VOLTAGE 12 (PREPPED)
Q1
60-79120-1
1 EACH
REGULATOR VOLTAGE 12 (PREPPED)
Q2
62-00014
2 EACH
MMBTA14 SOT-23 SMT
Q102, Q202
62-19140
12 EACH
1N914 HI SPD SMT 250mW DIODE
D201, D203, D204, D214, D7,
330.5 SMT .25W 1206 1%
3.3K SMT .25W 1206 1%
D8, D9
62-45650
3 EACH
33K SMT .25W 1206 1%
NJM4565 SMT DUAL HI FREQ
A1, A2, A3
62-04739
1 EACH
SMT DIODE ZENER 4739
Z1
62-54001
14 EACH
MMBT5401LT1 PNP SOT-23 SMT
R132, R232
Q10, Q11, Q12, Q13, Q16, Q20,
365K SMT .25W 1206 1%
Q21, Q22, Q23, Q26, Q3, Q4
3.9K SMT .25W 1206 1%
470.5 SMT .25W 1206 1%
4.7K SMT .25W 1206 1%
47K SMT .25W 1206 1%
R137, R17, R204, R205, R206,
R220, R23, R235, R237, R238
R10, R123, R124, R223, R224
LED YELLOW DIFFUSED 3MM T-1.00
D5
270.5 SMT .25W 1206 1%
0.0 SMT JUMPER 1206
R136, R236
2 EACH
LED GREEN DIFFUSED 3MM T-1.00
D102, D202
D10, D101, D103, D104, D11,
R104, R105, R106, R120, R135,
58-47055
LED RED DIFFUSED 3MM T-1.00
D12, D100, D200
R111, R211
R130, R131, R230, R231
100.5 SMT .25W 1206 1%
DIODE GEN RECT MR752 6A 200V
D1, D2, D3, D4
Q100, Q200
62-55500
6 EACH
470K SMT .25W 1206 1%
R140, R240
MMBT5550 NPN SOT-23
Q201, Q101, Q14, Q15, Q24, Q25
70-21050
1 EACH
FUSE ABC 5.00A FAST 6.35X32MM
F1
70-05713
2 EACH
RELAY SPDT 12A@120VAC/24V COIL
K1, K2
R5, R18
.47 OHM 5W 10% SB
TRANSISTOR 15A 100V PNP
Q19, Q29
R16
R129, R229, R26, R30
58-10025
60-00084
R25
0.047UF SMT 10% FILM 0805 50V
RES
220K SMT .25W 1206 1%
TRANSISTOR 15A 100V NPN
Q18, Q28
R12
39PF SMT 5% CERAMIC 0805
C106, C206
55-04705
2 EACH
R14
0.0033UF SMT 10% FILM 0805 50
C105, C115, C205, C215, C14,
TERMINAL VERT MALE PC MTG .250
QC7
06-40060
49-82052
60-00083
R24
220PF SMT 5% CERAMIC 0805
C101, C102, C114, C214, C201
22K SMT .25W 1206 1%
910.5 SMT .25W 1206 1%
R6, R7, R8, R9
R128, R228
C117, C217
03-92521
4 EACH
R27, R134, R234
0.1 uF SMT 10% FILM 1206 50V
C109, C209
2 EACH
2.2K SMT .25W 1206 1%
0.01UF SMT 10% FILM 080550V
C108, C208
49-47312
220.5 SMT .25W 1206 1%
C10, C110, C118, C119, C210,
C113, C213
REV B
58-91025
R121, R221
C202
DCM150 PCB Sub Assemblies
150K SMT .25W 1206 1%
R118, R119, R126, R133, R139,
C111, C211
ZINC CADMIUM
15K SMT .25W 1206 1%
C1, C2, C3, C4, C5, C6
C218, C219, C9, C13
ZINC CADMIUM
1.5K SMT .25W 1206 1%
680 SMT .25W 1206 1%
R127, R227, R4, R1, R2, R3
R109, R209, R110, R210
PCB REV B
42-22235
6 EACH
R28, R11
S1
30-01528
58-68025
R141, R241
S2, S3, S4
25-04201
1M SMT .25W 1206 1%
560.5 SMT .25W 1206 1%
R107, R207
R19, R22
H2A, H2B
25-02201
2 EACH
100K SMT .25W 1206 1%
CONNECT HEADER 4 PIN STRAIGHT
H3A, H3B
23-11010
58-56025
10K SMT .25W 1206 1%
XLR FEMALE CONNECTOR W/O GRND
INSLTR MICA .0020".830"X .69"
03-10450
2 EACH
3 EACH
J3, J4
03-00067-20 4 EACH
23-03529
R216, R29, R113, R213, R117, R217
JACK .250"PHONE STEREO PLASTIC
J1, J2
21-40000
1K SMT .25W 1206 1%
R112, R115, R116, R212, R215,
J5, J6
PART
CSOR206
LIMITED WARRANTY
71-09251
2 EACH
POT 9 D-P 25F B10K THREAD BSH
P1, P2
CARVIN ENGINEERING DATA
The DCM150 professional amp is designed utilizing Carvin’s years of experience in power amp technology. It meets and exceeds every standard for
professional amplification. The thick brushed anodized aluminum face plate,
large recessed knobs and heavy-duty aluminum chassis reflect the manufacturing quality within. The DCM150 “High Energy Transfer” amp carrys
the CE approval for world-wide use.
PURE—TRANSPARENT SOUND
Carvin considers the sound of an amp equally important as its reliability.
To insure pure, uncolored sound, we designed one of the fastest responding power amps on the market today. High slew rates deliver superb transient response. High frequencies are transparent and open—even at high
levels. Linear feedback circuits reduce distortion to near the theoretical zero
limit preventing any type of harshness which would lead to ear fatigue. The
DCM150 amp delivers flat, transparent, unaltered sound—especially important to the studio user. These amps are designed to deliver non-stop, continuous power and are completely protected from heat and short circuits.
ULTRA RUGGED FOR TOURING
Every chassis is made from heavy-duty 16 gauge aluminum that is lightweight and prevents rust. All internal cabling is neatly tied and harnessed.
Heavy-duty power switches, recessed knobs & machined aluminum front
panels all give the DCM amps a “tank-like” ability to handle rough, touring transport.
TOTALLY MODULAR
With the DCM150, Carvin brings you totally modular construction. If
you ever need an I/O (input/output) connector card because a connector
wore-out, just unplug it and re-install the replacement card in minutes.
You don’t have to de-solder anything. This applies to every aspect of the
DCM150 amp including the power supply, power cards, and heat sinks.
Everything is connected by heavy-duty connectors for easy replacement—even the Toroid transformer is a total plug-in.
LOSE THE WEIGHT...NOT THE PERFORMANCE
For some companies, weight reduction means cost reduction. Carvin however, uses expensive TOROID transformers to reduce weight. Toroids deliver
extra amounts of “on demand” current for continuous operation. This gives
the power supply a solid foundation, yielding more headroom. Not only do
toroids deliver high current, but they are known for reducing stray magnetic
fields eliminating hum & noise. This is especially important for the recording industry.
DCM150 POWER AMP
CSOR206
OPERATING MANUAL
FRONT PANELS & CONNECTING UP
The DCM Series feature front panel signal, clip and protect LEDs which let you monitor the status of the amp. Both channels use precision level controls allowing you
to see your settings at a glance. Balanced 1/4 phone & XLR input jacks are used to
eliminate hum & noise. Speaker outputs feature 1/4” jacks. Heavy-duty binding
posts that accept up to 50 amp #7 speaker wires.
The rear professional accessory group offers a GROUND switch to remove the
chassis ground from the XLR input, a PARALLEL input switch connects the inputs
of both channels together eliminating Y connectors and allowing amp patching
in multiple amp systems. The accessory group also features a BRIDGE mode switch
for delivering full power into a mono 8Ω loud.
RECEIVING INSPECTION—read before getting started
INSPECT YOUR UNIT FOR ANY DAMAGE which may have occurred during shipping.
If any damage is found, please notify the shipping company and CARVIN immediately.
SAVE THE CARTON & ALL PACKING MATERIALS. In the event you have to re-ship your unit,
always use the original carton and packing material. This will provide the best possible protection during shipment. CARVIN and the shipping company are not liable for any damage
caused by improper packing.
SAVE YOUR INVOICE. It will be required for warranty service if needed in the future.
SHIPMENT SHORTAGE. If you find items missing, they may have been shipped separately. Please allow several days for the rest of your order to arrive before inquiring.
RECORD THE SERIAL NUMBER on the enclosed warranty card or below on this manual
for your records. Keep your portion of the card and return the portion with your name
and comments to us.
DCM150 POWER AMP SPECIFICATIONS:
Output Power
(BRIDGE MONO)
8Ω, 1kHz, < 1% THD
150 Watts
Minimum Impedance (Bridged)
8 ohms
(Stereo, both channels driven)
8Ω, 1kHz, < 0.5% THD
4Ω, 1kHz, < 0.5% THD
Minimum Impedance
THD
20-20kHz
(8Ω typical)
Frequency Response
Input Impedance
Damping Factor
60/60 Watts
75/75 Watts
4 ohms per channel
< 0.1%
< 0.05%
±0.5 dB, 20 Hz to 20 kHz
> 20kΩ Balanced or Unbalanced
>400
Sensitivity (@ 4Ω)
1.0 Vrms
Output Noise
-102 dBm
Power Consumption
120V—200 VA
For your records, you may wish to record the following information.
Serial No._____________________ Invoice Date_______________
76-00150 0801
Dimensions
1 3/4” High x 19” Wide x 10” Deep
Weight (Net)
9lbs.
12340 World Trade Drive, San Diego, CA 92128
800 854-2235
www.carvin.com
CSOR206
FRONT & REAR PANEL CONTROLS
CLIP
SIGNAL
DCM150
13
15
17
19
12
22
30
50
PROFESSIONAL 150W AMPLIFIER
11 10 9
PROTECT
8
POWER
7
13
15
17
19
6
5
4
3
22
30
50
2
∞
1
0 dB
EQ EXPAND
3
5
DCM150
SPEAKERS
1
4Ω MIN.
BRIDGE
8 OHMS
MIN.
2
8
7
6
5
4
3
CLIP
SIGNAL
2
∞
1
0 dB
13
12
BRIDGE GND
LIFT
PAR
INPUT 1
4Ω MIN.
2
4
6
STEREO AMPLIFIER
8 OHMS/CH 50 WATTS
4 OHMS/CH 75 WATTS
8Ω BRIDGED 150 WATTS
800-854-2235
www.carvin.com
11 10 9
CHANNEL TWO
CHANNEL ONE
1
12
INPUT 2
MADE IN THE
USA
120VAC~60Hz
125VA INTERNAL FUSE
SERIAL NUMBER
14
9
10
11
7
8
FRONT PANEL
1. MOUNTING
The rack mounting holes are designed on ISO standard spacing. Four
10-32 x .5” phillip machine screws are normally used to secure the amp.
Rear support brackets are not required.
2. POWER SWITCH
Check the power amp connections and verify the AC line power source
before engaging the POWER switch. The yellow LED unmistakably indicates that all circuits are properly powered up. This color was chosen so
the operator could see the red protect indicator from a distance.
to signal –. The connector’s sleeve is then tied to ground through the GROUND
LIFT switch–.
9. SPEAKER OUTPUTS
The standard 1/4” SPEAKER jacks are used for most applications. Turn
the amp off before connecting your speakers.
10. SPEAKER BINDING POSTS
A precision input LEVEL attenuator is used to adjust the volume levels.
To deliver the amps full power without reducing headroom of the signal
source, the level controls should be turned up full.
For heavy-duty speaker connections, use the rear BINDING POSTS to connect your speakers. Wire sizes up to 7 gauge (50 amps) can be inserted
into the binding posts “side holes”. Larger cable can be used with “banana”
plugs which plug into the ends of the binding post (remove colored caps).
Binding posts are spaced on ISO standards. Use the two center RED binding posts for BRIDGE speaker connections (see 11 BRIDGE MODE).
4. CHANNEL SIGNAL INDICATOR
11. BRIDGE MODE—70V DISTRIBUTION SYSTEMS
3. CHANNEL LEVEL CONTROL
The green SIGNAL LED indicators will start to flash when there is a signal
passing to your speakers (-30dBM). This lets you know when the amp is
passing a signal to your speakers.
5. CHANNEL CLIP INDICATOR
The red CLIP LED indicators will start to flash when each channel has reached
its maximum output. Occasional flashing caused by lower bass frequencies
is OK. However, consistent flashing caused from higher frequencies may
damage high frequency drivers (excessive distortion). This does not cause
damage to the amp.
6. EQ EXPAND SWITCH
When set to the ‘in’ position this circuit will cut the mids by -4dB at 1KHz.
This works well as a loudness contour when operating at low volume levels
or adds tone when using it in a bass or guitar rack. When set to the ‘out’
position it provides a flat, normal response. Try it both ways and set as
desired.
REAR PANEL
7. XLR CHANNEL INPUTS
For most professional applications, use the XLR balanced input. This
will help to reduce hum and allow of longer cable runs from your signal
source (mixer, etc). Because this is a balanced input, the gain will be 6
dB higher than using a non balanced 1/4” input. XLR pin configuration:
Pin 1: Grounded through the GROUND LIFT switch, Pin 2: positive Bal.
signal and Pin 3: negative Bal. signal.
8. CHANNEL 1/4” PHONE JACK INPUT
These 1/4” TRS phone jacks are designed to receive either balanced or
unbalanced input signals. Balanced signals coming into this jacks should
be wired with the connector’s tip going to signal + and the connector’s ring
The DCM150 can be operated in bridge mode if you require a 70V distribution speaker system or a high powered mono (single channel) amp.
With your amp off, push in the rear BRIDGE switch after you have made
your speaker connections to the rear center RED binding posts (ch 1 is
+ and ch 2 is -). No other speaker jack or binding post can to be used at
the same time!”. The INPUT and LEVEL is handled by channel 1. Channel
2 is non-operational. The minimum speaker impedance is 8 ohms. CAUTION: The power developed by bridging your amp can destroy speakers!
12. PARALLEL OR “Y” INPUTS
The rear PARALLEL switch allows you to drive both channels from either
input. All signals entering any input will be available on both channels.
This eliminates Y adapter cables. This feature is used to “daisy chain”
one piece of equipment to another. Just plug into the unused INPUT (1/4”
or XLR) and it will become an output for other equipment.
13. INPUT GROUND LIFT
Many times sound systems are connected in such a manner to cause a
grounded loop with the inputs that result in audible hum. The input GND
LIFT (1/4” & XLR) switch on the rear panel will help eliminate this problem. If not, another way to eliminate ground loops is to install a “line matching” transformer between the amplifier input and the signal source and
cut the ground wire to PIN 1.
14. AC POWER
Your amp is designed to run on either 120V 60 Hz. The voltage range
for 120V is 95V to 132V. The rear heavy-duty AC cord is designed for your
country. Be sure to check your power source before plugging into a
grounded (3 prong) outlet. Never defeat the grounded connection or electrocution may result!
CONNECTING THE SYSTEM
CSOR206
SPEAKER CONNECTIONS
The following diagrams illustrate typical connections. Although these illustrations show
XLR’s for inputs and 1/4” plugs for outputs, a variety of alternative connectors are available.
For most stage setups, mono (not stereo) is recomended. The reason for this is the audience on the left will not hear the same program material on the right if the program is done
in true stereo.
INPUT CONNECTIONS
The preferred method of connecting input signals is with balanced XLR’s (two conductors
plus a shield wire such as Carvin professional XLR cables). Balanced input signals provide
the highest gain and best noise rejection. 1/4” stereo cables are also capable of providing
balanced input by using a stereo plug (tip-positive, ring-negative & sleeve-ground). Not all
sources provide balanced outputs. If this is the case, standard 1/4” input cables work fine
with cable lengths under 25 feet (single conductor plus shield) providing there is no ground
loop in the system.
There are two 1/4” speaker jacks available for speaker connections (one for each channel).
Additionally, there are two pairs of binding posts that not only allow for high current connections to speakers but are also used for “bridging” the amps output (see rear panel section 14 & 15). Use heavy gauge wire for all speaker connections (no lighter than 16 gauge
up to 50’, Carvin’s PH50). Caution: Never use shielded cable (microphone or instrument
input cable) to connect speakers. These cables will not handle the required current and may
cause your amplifier to oscilate because of the internal shield.
TYPICAL STEREO (BIAMP) SETUP
Ch 1 Left
(Hi Freq. Bi-Amp)
Ch 2 Right
TYPICAL MONURAL SETUP
(Lo Freq. Bi-Amp)
Use a XLR or 1/4" 2 or 3 cond. shielded cables
To signal use XLR or 1/4" 2 or 3 cond. shielded cable
DCM150
1
SPEAKERS
2
INPUT 1
STEREO AMPLIFIER
800-854-2235
www.carvin.com
PARALLEL switch
must be (IN)
DCM150
SPEAKERS
1
2
INPUT 1
STEREO AMPLIFIER
8 OHMS/CH 50 WATTS
4 OHMS/CH 75 WATTS
8Ω BRIDGED 150 WATTS
800-854-2235
www.carvin.com
BRIDGE
8 OHMS
MIN.
4Ω MIN.
PAR
MADE IN THE
USA
120VAC~60Hz
125VA INTERNAL FUSE
4Ω MIN.
BRIDGE
8 OHMS
MIN.
INPUT 2
BRIDGE GND
LIFT
4Ω MIN.
USA
120VAC~60Hz
125VA INTERNAL FUSE
SERIAL NUMBER
PAR
SERIAL NUMBER
BRIDGE switch
must be OFF (OUT).
Full Range
(Hi Freq. Bi-Amp)
Horn System
INPUT 2
BRIDGE GND
LIFT
4Ω MIN.
8 OHMS/CH 50 WATTS
4 OHMS/CH 75 WATTS
8Ω BRIDGED 150 WATTS
MADE IN THE
BRIDGE switch
must be OFF (OUT).
Ch 1 Speaker
Use 16 guage or heavier
Non shielded cables (PH50).
Plug into the 1/4" speaker jacks
or strip and insert into speaker
Binding Post (Red+ Black-)
Ch 2 Speaker
Use 16 guage or heavier
Non shielded cables (PH50).
Plug into the 1/4" speaker jacks
or strip and insert into speaker
Binding Post (Red+ Black-)
Full Range
(Lo Freq. Bi-Amp)
Woofer System
BALANCED MIC/LINE XLR CABLES
-NEG.
Activate the BRIDGE switch
(IN). Control the level by Ch 1
( Ch 2 does not function.
Use a XLR or 1/4" 2 or 3 cond. shielded cables
DCM150
1
SPEAKERS
2
INPUT 1
STEREO AMPLIFIER
8 OHMS/CH 50 WATTS
4 OHMS/CH 75 WATTS
8Ω BRIDGED 150 WATTS
800-854-2235
www.carvin.com
4Ω MIN.
BRIDGE
8 OHMS
MIN.
3
SHIELD
TYPICAL BRIDGED SETUP
2
1
1
INPUT 2
BRIDGE GND
LIFT
4Ω MIN.
+POS.
SHIELD
PAR
MADE IN THE
USA
120VAC~60Hz
125VA INTERNAL FUSE
SERIAL NUMBER
2
+POS.
-NEG.
70V Distribution System:
"TAP" Wattage of transformer
(can vary from diagram)
divided by total wattage
of Amp = Number of
transformer/speaker(s)
that can be hooked up.
3
GND
1
+ SIGNAL (BAL.)
2
3
- SIGNAL (BAL.)
OR
INTERRUPT (PATCH)
STEREO OR BALANCED SIGNAL LINE
Single speaker or
system connected
in BRIDGE mode.
Minimum imp. 8
+ SIGNAL (RETURN)
- SIGNAL (SEND)
SHIELD (GROUND)
15w
16
15w
16
7w
8
7w
8
3w
4
3w
4
1w
+
C
(Shielded)
SPEAKER OR SIGNAL LINE CABLE
+ TIP (HOT)
1w
C
(Unshielded)
+
C
C
SHIELD (GROUND)
(Shielded)
CSOR206
Option DD)
U2020
100-Channel UHF Wireless System
We can summarize
the advantages of our
U2020 wireless system
in one word: More.
Vega offers more brands of handheld microphone
elements, like the Audix® OM6,
Audio-Technica® ATM89R,
Electro-Voice® N/D767 and
many others, plus a large selection of lavalier mics.
The U2020 has 380 available frequencies – that’s 165
more usable frequencies than our nearest competitor.
High-selectivity receiver allows more systems at one
location; up to twenty U2020’s work simultaneously
without interference.
A full 50 mW of transmitter output power results in
a typical range of 1000 feet, more than double the
range of most other systems.
More applications for local broadcasters, theaters,
Houses of Worship, live concerts, theme parks,
schools and rental houses.
www.clearcom.com
CSOR206
U2020
100-Channel UHF Wireless System
Specifications
B
SQUELCH AUDIO
ATTEN
MIC
12V DC
AUDIO OUT
A
LINE/MIC/OUT
LINE
R-2020 RECEIVER CONTROL PANEL AND CONNECTORS
2.1 MM
POWER
JACK
12V DC
B
A
MC-2020 MULTICOUPLER PANEL AND CONNECTORS
B
A
B
B
A
B
A
B
A
B
A
4-UP SYSTEM WITH MULTICOUPLER
A
B
A
B
A
B
A
B
A
B
A
B
A
B
A
6-UP SYSTEM WITH TWO MULTICOUPLERS
The MC-2020 multicoupler powers all receivers through the antenna cables,
eliminating extra power supplies in the rack (front or back antenna mounting
allows even more installation flexibility). Ask for our Vega Applications Guide for
more configurations and information.
AUTHORIZED VEGA DEALER
U2020 System
Frequency Band: . . . . . . 708-782 MHz (4 bands A, B, C, D;
C & D bands recommended for U.S.)
Frequency Settings: . . . . . 100 channels (00-99)
Audio Frequency Response: . 50-15,000 Hz, ± 1.5 dB
Range: . . . . . . . . . . . 1,000 ft (300 m); 200-300 ft
(60-90 m) in adverse conditions
Audio Processing: . . . . . DX20 2:1 logarithmic companding
Emission/Modulation: . . . . FM, 180KF3E
Harmonic Distortion: . . . . < 0.25% (1 kHz)
Ultimate S/N: . . . . . . . . > 100 dB (A-weighted)
Squelch Quieting: . . . . . . 102 dB (A-weighted)
Audio Output
Line Level: . . . . . . -26 to +4 dBm
Mic Level: . . . . . . -56 to -26 dBm
IF Selectivity: . . . . . . . . 280 kHz
RF Selectivity: . . . . . . . 22 MHz
Adjustment and Control: . . Power, two 10-position frequency
select switches, 30-dB level, 30-dB
switchable pad, squelch control
Indicators: . . . . . . . . . Audio level meter (5 position), RF
level meter (5 position), Power,
Diversity
Power: . . . . . . . . . . . 5W maximum
Weight: . . . . . . . . . . . 1 Lb, 14 oz (.85kg)
Dimensions (hwd): . . . . . 1.65 x 7.15 x 9.25 inches
(4.2 x 18.2 x 23.5 cm)
Handheld Transmitter
Microphone Elements:
. . . Audix® OM6, A-T® ATM89R,
EV® N/D767, N/D557, and N/D267.
Other elements available; consult
the Vega factory for availability.
Power Output: . . . . . . . 50 mW
Frequency Stability: . . . . . ± 0.005%
Spurious Output: . . . . . . -53 dB maximum
Controls: . . . . . . . . . . Power, Mute on/off, Mic level
Audio Adjustment Range: . . 30 dB
Antenna: . . . . . . . . . . Internal dipole
Battery Life: . . . . . . . . > 6 hours
Length (varies with element): . . Approx. 10.6 in (26.9 cm)
Weight, with battery (varies): . Approx. 10 oz (283.5 g)
Bodypack Transmitter
Power Output: . . . . .
Frequency Stability: . . .
Spurious Output: . . . .
Controls: . . . . . . . .
Connector type: . . . . .
Audio Adjustment Range:
Antenna: . . . . . . . .
Battery Life: . . . . . .
Dimensions (hwd): . . .
Manufactured by: Clear-Com Intercom Systems
4065 Hollis StreetEmeryville, California 94608
(510) 496-6666 • Fax (510) 496-6699 www.clearcom.com
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
50 mW
± 0.005%
-53 dB maximum
Power, Mute on/off, Mic level
4-pin Tini QG
30 dB
1/4-wave flexible whip
> 6 hours
4 x 2.5 x 1.0 in
(10.16 x 6.35 2.54 cm)
Weight, with battery: . . . . 5.5 oz (155.7 g)
CSOR206
(Option EA)
*smith&nephew
640
Image Management System
The Smith & Nephew 640 Image Management System offers the tools to facilitate
documentation needs, including the easy acquisition, review and export of digital
video clips, still images, and patient reports. In addition, the Windows® 2000
platform provides user screens that are easy to follow, compatibility with a variety
of printers and DVD recorders, and a system that can easily be networked.
CSOR206
Features
Provides acquisition of still images and video clips in
industry standard file formats (JPEG, bitmap, MPEG1 or
MPEG2)
Incorporates on-screen thumbnail review of still images
and video clips, functionality for adding procedure notes,
a choice of report formats, and the ability to connect an
optional touch panel monitor
Specifications
Video Inputs
Video Outputs
Video Formats
Network Port
HERMES™ Port
VGA Port
Printer Port
USB Port
Power Requirements
Motion Video
Resolution
Still Image Capture
Resolution
Dimensions
Weight
Hard Drive
Processor
Operating System
Endoscopy
Smith & Nephew, Inc.
Andover, MA 01810
USA
RGBS, S-Video, AUX Input, (Composite)
RGBS, S-Video, AUX Input, (Composite)
NTSC and PAL
Ethernet 10-Base-T/100 Base-TX,
auto-select
RS-232 with USB type B,
bidirectional port
16-pin female port
Female DB-25 parallel port,
bidirectional input/output
USB Type A, software compatible
with NS16C550
100–120/200–230 VAC,
50/60 Hz @ 150 VA
MPEG1=352 x 240 (NTSC)
352 x 288 (PAL)
MPEG2=704 x 480 (NTSC)
704 x 576 (PAL)
BMP=640 x 480 (24-bit color)
JPEG=640 x 480
DICOM=640 x 480
18 l x 17 h x 6.64 w (inches)
45.72 x 43.18 x 16.87 cm
21 lbs (9.5 kg)
20 GB
300 MHZ Intel Celeron
Processor
Windows 2000
www.smith-nephew.com
T 978 749 1000
US Customer Service: 1 800 343 5717
International Customer Service: +1 978 749 1140
Generates an HTML report, allowing for easy, web-based
surgical image management
Supports a variety of Windows 2000 compatible printers
and allows the user to choose their own printer (inkjet,
laser, etc.)
Offers compatibility with HERMES® Digital O.R. Control
Center and seamless integration with Smith & Nephew’s
DORAweb™ Information System
Ordering Information
Please contact customer service for product availability
7210235
640 Image Management System, English On-Screen
Display and Operations Manual, U.S. Power Cord
7210237
640 Image Management System, Multi-language
On-Screen Display and Operations Manual, Continental
Power Cord
7210239
640 Image Management System, English On-Screen
Display and Operations Manual, U.K. Power Cord
Accessories
7210344
Touch Panel, LCD, 15 inch (domestic)
7210345
Touch Panel, LCD, 19 inch (domestic)
7207448
Iomega® 100 MB Zip… Disk
7207447
Iomega 250 MB Zip Disk
7209339
Single-pedal footswitch
7209340
Dual-pedal footswitch
7209338
650 MB or 700 MB CD-R Media
7210432
Single Arm, Vertical Mount
7210433
Double Arm, Vertical Mount
7210434
Double Arm, Desk Mount
7210435
Wall Mount Bracket
™ Trademark of Smith & Nephew.
All other trademarks acknowledged
©2003 Smith & Nephew. All rights reserved.
Printed in USA. 10/03 1061453 Rev. A
CSOR206
(Option ED)
The New Surgical Display Standard
RadianceTM 19
·
Ultra High Bright - High Contrast
·
Image Lag ReductionTM Technology
·
Super Fast Response
·
Picture PerfectTM Technology
·
Medical-Grade UL/IEC-60601-1
·
Splash Proof
·
24 VDC Remote Power
The Radiance series of surgical displays are ideally suited for use with minimally invasive surgical equipment in the OR.
These medical grade devices exceed the stringent performance and safety requirements necessary for use in a surgical
environment, where superior image quality, true color reproduction, exceptional contrast, and high brightness are required.
For mounting on light arms, the external 24Vdc power supply can be located up to 100 feet away from the display.
Picture-Perfect TechnologyTM
PPTTM technology, invented and used by NDS in manufacturing Radiance displays, eliminates the jagged edges that appear
when interlaced video signals are displayed on a progressive scan flat-panel device (LCD or Plasma). NDS PPT uses
proprietary angle correlated vector interpolation algorithms to eliminate intra-field spatial interpolation (staircasing
effect), and enhances the visual quality necessary for tying sutures, examining tissues and other delicate procedures.
Image Lag Reduction (ILR) for Super Fast Video Imaging
Proprietary Image Lag Reduction technology (ILR), developed at NDS in conjunction with PPT, provides the fastest video
imaging available in the market today. ILR technology anticipates the LCD drive required from one video frame to the
next and modifies the LCD sub-pixel drive level to provide an industry-leading fast response time. These advanced
interpolation and smoothing algorithms, result in images presented lag-free. Equipped with ILR technology, the Radiance
display family delivers the fastest response time of any flat-panel display (between 10 and 16ms response time).
Certifications/Compliance
EN 60601-1, UL 60601-1 (Classified), MDD 93/42/EEC, IEC-601.1, EN 46001, CE, ISO 9001, ISO 13485,
Class I Medical Device, FDA Registration #2954921
The Intelligent Solution
CSOR206
The New Surgical Display Standard
With 24Vdc power input,
the Radiance is a perfect solution
for boom arm mounting.
Surgical and Radiology Support
The Radiance display supports eight different video formats, including SDI, DVI digital, VGA analog, RGBS, Component
Video, (YPbPr), S-Video(Y/C), Composite, and Sync-On-Green (SOG). And with gamma correction included, the Radiance is
a perfect solution for fluoroscopy, ultrasound, PACS, MR, DR, etc.
Remote Functionality Control for Switching Signals in Real-Time
Integrated Operating Rooms require that display adjustments and video image source switching occur in real-time,
without the intervention of the surgeon in the sterile field. Radiance displays answer this requirement with Remote
Functionality Control (RFC) technology. All Radiance displays deliver RFC via a serial communication port located on the
display.
General Purpose Input Connector
The General Purpose Input/Output (GPIO) connector allows customization to the Radiance display. It can be connected to
a foot pedal to provide the surgeon with the ability to switch between different video sources, or be used to invoke the
Tally-LampTM indicator.
Medically Manufactured
The Radiance is a professional medical device designed specifically for the OR environment. Unlike many LCD
manufacturers who fashion existing off the shelf displays into medical equipment, this flat-panel is designed from the
ground up for extreme durability and safety. Membrane style buttons and a non dimpled enclosure ensures particles or
other foreign matter won’t accumulate into voids and possibly spread contaminants. The unit is designed to run without
fans of any sort (internal or external) that could possibly make contaminants airborne and spread bacteria. Designed for
safety, the low voltage input eliminates concerns with running mains power through a metal arm. In addition, the low
voltage design allows the external power supply to be located up to 100 feet away from the display.
The Intelligent Solution
CSOR206
Radiance 19-inch specifications
General
Viewing Area (Diagonal)
inches
mm
Active Area
Inches
mm
Pixel pitch (mm)
Native Resolution
Luminance (cd/m2)
Contrast ratio
# of Colors
Color Gamut
(% SMPTE 296M, HD std.)
Viewing Angle (degrees)
Response
Gamma:
Display Technology
Power Requirements
Display
DC Power Supply
Power Consumption
Dimensions
inches
mm
Weight (lbs.)
Inputs
(for video input formats, see pg.4)
Horiz Freq (kHz, max)
Vertical Freq (Hz, max)
Bandwidth (MHz, max)
SDI
S-video
RGBS, YPbPr
Composite
Sync-On-Green (SOG)
Graphics Inputs
DVI
VGA
Control Inputs
RS-232
GPIO
Outputs
SDI
S-Video
RGBS
Composite
User Controls
OSD
Operating Conditions
Temperature
Operating
Storage
Humidity
Operating
Storage
Mounting
NDS North America
Corporate Headquarters
16245 Vineyard Blvd.
Morgan Hill, CA 95037
TEL: 408.776.0085
FAX: 408.776.9878
email: [email protected]
19”
483
14.8 x 11.9
376 x 301
0.294
1280 x 1024 (SXGA)
450
650:1
16.77 million
100
±85
10-16ms; gray — to — gray
1.8, 2.0, 2.2, 2.4, color corrected video gamma, & PACS
a-Si TFT
16 – 24 VDC
100 to 240 VAC ± 10%, 50/60 Hz
40W
18 x 16 x 4
465 x 400 x 98
14
(6.4 Kg)
75
85
135
BNC, 75 Ω terminated
BNC x 2 (Y & C), and DIN-4, 0.7 Vp-p ± 6db, 75 Ω terminated
BNC x 4, or HD-15, 0.7 Vp-p ± 6db, 75 Ω terminated
BNC, 0.7 Vp-p ± 6db, 75 Ω terminated
BNC x 3, 75 Ω terminated
DVI-d
HD-15
DB-9
DIN-6
BNC
DIN-4
BNC x 4, and HD-15
BNC
R, G, B adjust, Hue, Saturation adjust, Color Temperature: D55/D65/D80/D93
Contrast, Brightness, Backlight Level , Horizontal & Vertical Position
Overscan: Off / On (up to 25% overscan), Phase & Frequency
0 to +40 °C
-20 to +60 °C
20 – 85 %RH
5 – 85 %RH
100 mm VESA
NDS Europe
Nijverheidscentrum 2D
2761 JP Zevenhuizen (ZH)
The Netherlands
Phone number : 0031 180 63 43 56
Fax number:
0031 180 63 21 91
www.nationaldisplay.com
CSOR206
Video Input Formats
Format
Input
Digital Analog
Serial
576/50i (PAL) SDI
480/60i (NTSC) SDI
576/50p
480/60p
720/50p
720/60p
1080/50i
1080/60i
Up to 1024/60p
Comp, S-video, RGB, YPBPR
Comp, S-video, RGB, YPBPR
RGB, YPBPR, SOG
RGB, YPBPR, SOG
RGB, YPBPR
RGB, YPBPR
RGB, YPBPR
RGB, YPBPR
SOG
Horiz. Freq (kHz)
Interlace /
Progressive
Aspect
Standard
Digital/Analog
15.625
15.734
31.250
31.469
37.500
45.000
28.125
33.750
64.0, max
Int
Int
Prog
Prog
Prog
Prog
Int
Int
Prog
16:9 / 4:3
16:9 / 4:3
16:9 / 4:3
16:9 / 4:3
16:9
16:9
16:9
16:9
-
SMPTE
SMPTE
-
259M/C ITU 601
259M/C ITU 601
SMPTE 293M
SMPTE 296M
SMPTE 296M
SMPTE 274M
SMPTE 274M
-
All product names, trademarks or registered trademarks are the property of their respective holders.
** NDS continuously enhances its products, therefore specifications are subject to change without notice.
NDS North America
Corporate Headquarters
16245 Vineyard Blvd.
Morgan Hill, CA 95037
TEL: 408.776.0085
FAX: 408.776.9878
email: [email protected]
NDS Europe
Nijverheidscentrum 2D
2761 JP Zevenhuizen (ZH)
The Netherlands
Phone number : 0031 180 63 43 56
Fax number:
0031 180 63 21 91
www.nationaldisplay.com
Doc # Radiance 19” 60D0018A
CSOR206
Communication Color Video Camera
(Opton F)
The Sony EVI-D100 (NTSC) and
EVI-D100P (PAL) video cameras are
a great choice for any application
that requires a high-quality color
video camera with the flexibility of
remote pan/tilt/zoom operation, all
in a compact easy-to-use package.
These high quality CCD cameras
combine a high-speed, quiet pan/
tilt with a wide angle of view
and 40x zoom. Auto focus and
automatic exposure control with
back light compensation are fast
and stable and can easily cope
with difficult lighting conditions.
The EVI-D100/P models are
ideal for applications such as
videoconferencing, distance learning
and corporate training, surveillance,
telemedicine, sports, concerts
and internet communications such
as webcasting. Additional advantages are provided by easy to
use presets, daisy-chaining capability
and various digital picture effects.
EVI-D100
EVI-D100P
Component/OEM
FEATURES
• High Speed, Wide Range Pan/Tilt
The camera moves to a designated position quickly and
immediately with one of the highest pan/tilt speeds in its class.
Max. Pan speed: 300 degrees/s (range ± 100 degrees)
Max. Tilt speed: 125 degrees/s (range ± 25 degrees)
• Quiet Operation
Direct drive motors account for the gearless structure of
the camera, reducing the noise of pan/tilt motion drastically
compared to conventional models.
• 40x Zoom Ratio (10x Optical + 4x Digital)
The fast and stable auto focus zoom lens reaches an
impressive 40x zoom ratio.
• Built-in Conversion Lens for Wide Angle View (65 degrees)
The EVI-D100/D100P incorporates a newly developed
wide-angle lens for wide field of view image capturing,
making it ideal for use in small-sized rooms.
• Six Position Presets with Battery Back-up
An integral back-up battery stores presets of pan/tilt/zoom,
focus position, AE mode and White balance mode, even
when the unit is powered off.
• Auto Sleep Function
The camera can be set to automatically turn off when not in
use after a specified period of time.
• Various Picture Effects
Mirror Image, Still Image on Field Memory, Pastel Image,
Negative/Positive Reversal, Enhanced Contrast, etc.
• Multi-function IR Remote Commander® unit
Easy-to-use supplied remote commander unit is useful for
basic pan/tilt/zoom camera control.
• RS-232C Serial Control by VISCATM
Control all camera settings and pan/tilt/zoom functions
remotely via PC.
this is not a rehearsal.
w w w.sony-vision.com
CSOR206
SPECIFICATIONS
EVI-D100
Video Signal
Image Sensor
Effective Pixels
Horizontal Resolution
Lens
Horizontal Angle of View
Minimum Object Distance
Minimum Illumination
Auto Exposure
Shutter Speed
White Balance
Effects
EVI-D100P
NTSC
PAL
1/4 type Super HAD CCD
768 (H) x 494 (V)
752 (H) x 582 (V)
470 TV lines (Wide end)
460 TV lines (Wide end)
x10 Optical Zoom, x40 with Digital Zoom, f = 3.1 to 31, F 1.8 to 2.9
6.6 to 65 degrees
100 mm (Wide end), 600 mm (Tele end)
3.5 lx (F1.8)
Auto/Manual/Priority AE, Exposure compensation, Back light Compensation
1 ⁄ 4 to 1 ⁄ 10,000 s
1 ⁄ 3 to 1 ⁄ 10,000 s
Auto, ATW, Manual, One Push, 3200K, 5800K
Mirror Image, Still Image on Field Memory, Pastel Image, Negative/Positive Reversal, Sepia Image,
Monochrome Image, Enhanced Contrast, Mosaic Image, Vertical Stretch, Horizontal Stretch, Motion Image on Still Image,
Continuous Still Image, Motion Images on Binaried Still Image, After-image Lag of Moving Object
More than 50 dB
Horizontal ± 100 degrees (Max speed 300 degrees/s),
Vertical ± 25 degrees (Max speed 125 degrees/s)
(in 0.07 degrees increments)
VBS, Y/C
DC 10.8 to 13.0 V
Max. 13.2 W (at 12 Vdc)
0 to 40 °C (32 to 40 °F)
-20 to 60 °C (-4 to 140 °F)
113 (W) x 120 (H) x 132 (D) mm (4 1⁄2 x 4 3⁄4 x 5 1⁄4 inches)
860 g (1 lb 14 oz)
AC Adaptor (x1), IR Remote Commander unit (x1), Velcro tape (x1), Operating Instructions (x1)
S/N Ratio
Pan/Tilt
Video Output
Power Requirements
Power Consumption
Operating Temperature
Storage Temperature
Dimensions
Weight
Supplied Accessories
DIMENSIONS
PAN/TILT RANGE
Unit: mm
120
100
°
24.5° *
POWER
RECIVE
113
132
0°
10
24.5° *
25°
19
°*
Tripod Screw
25°
°*
19
BACKUP
ON
OFF
IR SELECT
1 2 3
VIDEO
S VIDEO
IN VISCA OUT
DC IN
12.0V
*Angle of view
Product information
is available on the
Sony Home Page
Click!
http://www.sony-vision.com
Sony Belgium (ICS) +32 2 724 18 24
Sony France (ICS) +33 1 55 90 41 58
Sony Germany (ICS) +49 221 537 8923
Sony Italy (ICS) +39 02 61 83 84 06
Sony Netherlands (ICS) +31 20 658 1502
Sony Nordic (ICS) +46 40 19 08 06
Sony Spain (ICS) +34 902 41 51 61
Sony UK (ICS) +44 1932 816 340
© 2001 Sony Corporation. All rights reserved.
Reproduction in whole or in part without written permission is prohibited.
Design and specifications are subject to change without notice.
CA EVI-D100/100P/GB- / /2001
CSOR206
(Option F)
CSOR206
CSOR206
CSOR206
(Option G)
Displays up to four
NTSC/PAL video inputs
in scalable windows on
a single screen
Genlock capability
Composite and S-video inputs
Composite and S-video
multi-image outputs
Horizontal & vertical sizing,
positioning, and blanking
controls for each window
MVP 104GX - MULTI VIDEO PROCESSOR
Factory/user preset
configurations
Built-in stereo audio switcher
RS-232/422 control
CSOR206
APPLICATION
SPECIFICATIONS
Extron’s MVP 104GX is a multi video processor that allows a user to display
up to four video signals simultaneously on a single screen for more powerful
communications. Videoconferencing and distance learning applications
benefit from the MVP 104GX’s independent input sizing and advanced
decoding using a three-line adaptive comb filter. The MVP 104GX allows
participants at the far end of a videoconference to view multiple images on
one screen. This capability enables one or more participants at the near end
to remain on-screen for face-to-face discussion while computer-video or
other images are displayed.
Video input and loop-through
Number/signal type ............................. 4 S-video, 8 composite
Connectors .......................................... 8 female BNCs, 4 4-pin mini-DIN
Nominal level ...................................... 0.7V to 1V p-p
Maximum level .................................... 2V p-p
Input impedance ................................. 75 ohm
Input frequency range ......................... NTSC/PAL
Video output
Connectors .......................................... 1 4-pin mini-DIN for S-video
2 female BNCs for composite
Output standards ................................. Composite & S-video
Nominal video level ............................. 0.7V to 1V p-p
Impedance ........................................... 75 ohms
Standards ............................................. NTSC 3.58, PAL
Audio input
Number/signal type ............................. 4 stereo, balanced/unbalanced
Connectors .......................................... 4 3.5 mm captive screw terminals, 5 conductor
Impedance ........................................... Unbalanced 50 k ohms, DC coupled,
Balanced 25 k ohms, DC coupled
Audio output
Number/signal type ............................. 1 stereo, balanced/unbalanced
Connectors .......................................... 1 3.5 mm captive screw terminals, 5 conductor
Control/remote – video processor
Serial control port ................................ 9-pin standard RS-232/RS-422
Baud rate ............................................. 9600
Protocol ............................................... 8-bit, 1 stop bit, no parity
General
Power .................................................. 100-240VAC, 50/60 Hz, 40 watts, internal
Enclosure dimensions .......................... 3.5" H x 17.5" W x 10.1" D
8.8 cm H x 44.5 cm W x 25.6 cm D
Shipping weight ................................... 15 lbs (6.8 kg)
Part number ............................................. 60-320-02
Each video window can be independently scaled, positioned, or overlapped,
so the user may display different window configurations such as picture in
picture (PIP) or quad splitting. Horizontal and vertical sizing, positioning,
and blanking controls are provided for each source. Images are routed from
sources such as document cameras, CODEC cameras, VCRs, or DVD
players. The windows can be labeled using up to 16 alphanumeric
characters for on-screen identification, and a background color may be
chosen to fill any unoccupied area. The “GX” version adds genlock
capability for use in a system that requires synchronous timing.
FEATURES
■ Inputs – Accepts up to four NTSC or PAL video inputs. Two inputs
accept composite video or S-video, and two inputs accept composite
video only.
■ Multi-image outputs – Three multi-image outputs provided
simultaneously: two composite video outputs on BNCs
and one S-video output on a 4-pin mini-DIN connector.
■ Picture controls – Provides horizontal & vertical sizing, positioning,
and blanking controls for each window.
■ Freeze control – Includes freeze function to freeze individual windows
of the multi-image output. Freezing all windows simultaneously is
available through RS-232.
■ Factory/user preset memories – Convenient, one-touch selection of
different windowing configurations during videoconferencing
presentations available using 20 factory and 24 user memories for one,
two, three, or four window display outputs. Presets include horizontal
and vertical sizing, positioning, blanking, and priority settings for each
window.
■ Blanking control – Extron’s exclusive variable horizontal and vertical
blanking for each window. Using blanking, a user may add black lines
at the edges of the window to eliminate edge noise.
■ Audio switching – Features 4 x 1 stereo audio switcher with 3.5 mm captive
screw connectors for selecting the desired audio of any video input.
APPLICATION DIAGRAM
Extron
VSC 150
PC Computer
External
Genlock
Timing
Scan
Converter
GEN
RS-232 Control
K
LOCIN
Y
B/B32
G/Y
RS-2
OUT
Y
R/R-
HEIM
ANA
AV.
Extron CERRITOS
5
LEWIS ST.
Y
DOUGLAS RD.
AV.
LINCOLN
RGB
B-Y/
R-Y/
Anaheim
RD.
WEST ST.
BALL
Disneyland
HASTER ST.
75 OHM
57
BLVD.
PAL OUT
ST.
MAC
ANAHEIM
0.3A
0V
H
S-VID
EAST
■ Input and preset labels – For easy recognition of input and preset buttons,
the MVP 104GX allows the user to insert custom defined labels printed
using Extron’s Windows®-based software, which provides text and/or
graphics on customized labels.
EO
O
U
EO
T
P S-VID
U
T
S
STATE COLLEGE BLVD.
S
V
O
VIDE
I
N
P
U
T
S
Stadium
AV.
KATELLA
100-24
VGA
RS-
T
TPU
OU R
1
L
Hz
50/60
L
T
OU
TPU
L
L
INP
INP
INP
UT
IN
INP
UT
2
UT
UT
4
1
2
UTS 3
INP L
R
4
232
OTE
REM
R
R
R
A
C
3
IN
B
IN
OUT
Videoconferencing System
OUT
1
OUT
IN
HEIM
ANA
57
BLVD.
LEWIS ST.
CERRITOS
DOUGLAS RD.
AV.
Extron
5
0.5A
Anaheim
WEST ST.
Disneyland
HASTER ST.
RD.
BALL
40V
100-2
Stadium
AV.
KATELLA
AV.
TOS
CERRI
Extron
Anahei
ST.
AV.
m
AH
STATE
ST.
Stadium
EI
M
BLVD.
COLLEGE
RD.
AN
57
Plasma Display
EAST
ANAHEIM
BLVD.
DOUGLAS
5
LINCO
LN
LEWIS
ST.
ST.
RD.
and
Disneyl
HASTER
LA
KATEL
AV.
BALL
WEST
Extron Electronics, USA
1230 South Lewis Street, Anaheim, CA 92805
800.633.9876 714.491.1500 FAX 714.491.1517
USA
ST.
ANAHEIM
AV.
LINCOLN
Hz
50/60
MVP 104GX
■ RS-232 remote control – Extron’s Simple Instruction Set™ is provided
for RS-232 control via Extron’s Windows®-based control program or
third-party control.
■ Executive mode – Locks out front panel adjustments; all functions,
however, remain active through RS-232.
EAST
■ Genlock – Features the ability to genlock to an external black burst signal
for use in timed or live environments that require genlock.
STATE COLLEGE BLVD.
OUT
Document Camera
Extron Electronics, Europe
Beeldschermweg 6C, 3821 AH Amersfoort
+31.33.453.4040 FAX +31.33.453.4050
The Netherlands
VCR
Video Camera
Extron Electronics, Asia
135 Joo Seng Rd. #04-01, PM Industrial Bldg.
+65.383.4400 FAX +65.383.4664
Singapore 368363
VCR
Extron Electronics Information
ExtronWEB™: www.extron.com
ExtronFAX™: 714.491.0192
24-hour access—worldwide!
00-08
68-504-01
REV. B