product guide model 463211513 - Char

PRODUCT GUIDE
MODEL 463211513
Classic C-46G3D
IMPORTANT: Fill out the product record information below.
Serial Number
See rating label on grill for serial number.
Date Purchased
For support and to register your
grill, please visit us at
www.charbroil.com
If you have questions or need
assistance during assembly,
please call 1-800-241-7548.
© 2013 Char-Broil, LLC Columbus, GA 31902
Printed in China
Assembly instructions © 2013
07/25/12 • G560-001-100801
TABLE OF CONTENTS
DANGER
For Your Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Grilling Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Use and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-13
Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Parts List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Parts Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
If you smell gas:
1.
2.
3.
4.
Shut off gas to the appliance.
Extinguish any open flame.
Open lid.
If odor continues, keep away from the
appliance and immediately call your gas
supplier or your fire department.
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-24
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-27
Registration Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Safety Symbols
The symbols and boxes shown below explain what each heading
means. Read and follow all of the messages found throughout
the manual.
WARNING
1. Do not store or use gasoline or other
flammable liquids or vapors in the vicinity of
this or any other appliance.
2. An LP cylinder not connected for use shall not
be stored in the vicinity of this or any other
appliance.
WARNING
WARNING: Indicates a potentially hazardous situation
which, if not avoided, could result in death or serious injury.
WARNING
Failure to follow all manufacturer’s instructions could
result in serious personal injury and/or property damage.
CAUTION
CAUTION: Indicates a potentially hazardous situation or
unsafe practice which, if not avoided, may result in minor
or moderate injury.
DANGER
DANGER: Indicates an imminently hazardous situation
which, if not avoided, will result in death or serious injury.
INSTALLER/ASSEMBLER:
Leave this manual with consumer.
CONSUMER:
Keep this manual for future reference.
CAUTION
For residential use only. Do not use for commercial
cooking.
CAUTION
Read and follow all safety statements, assembly
instructions, and use and care directions before
attempting to assemble and cook.
CAUTION
Some parts may contain sharp edges.
Wear protective gloves if necessary.
THIS GRILL IS FOR OUTDOOR USE ONLY.
2
WARNING
CALIFORNIA PROPOSITION 65
1. Combustible by-products produced when using
this product contains chemicals known to the State
of California to cause cancer, birth defects, or
other reproductive harm.
2. This product contains chemicals, including lead
and lead compounds, known to the State of
California to cause cancer, birth defects or
other reproductive harm.
CAUTION
Using pots larger than 6 quarts in capacity could
exceed weight limit of the
side burner shelf
or side shelf,
resulting in failure
of grill cart
components.
Wash your hands after handling this product.
Installation Safety Precautions
• Use grill, as purchased, only with LP (propane) gas and the
regulator/valve assembly supplied. If your grill is Dual Fuel ready,
a conversion kit must be purchased for use with natural gas.
• Grill installation must conform with local codes, or in their
absence of local codes, with either the National Fuel Gas
Code, ANSI Z223.1/ NFPA 54, Natural Gas and Propane
Installation Code, CSA B149.1, or Propane Storage and
Handling Code, B149.2.
• All electrical accessories (such as rotisserie) must be
electrically grounded in accordance with local codes, or
National Electrical Code, ANSI / NFPA 70 or Canadian
Electrical Code, CSA C22.1. Keep any electrical cords and/or
fuel supply hoses away from any hot surfaces.
• This grill is safety certified for use in the United States and/or
Canada only. Do not modify for use in any other location.
Modification will result in a safety hazard.
WARNING
Do not attempt to repair or alter the
hose/valve/regulator for any “assumed” defect. Any
modification to this assembly will void your warranty
and create the risk of a gas leak and fire. Use only
authorized replacement parts supplied by
manufacturer.
CAUTION
Grease Fires
• Putting out grease fires by closing the lid is not
possible. Grills are well ventilated for safety reasons.
• Do not use water on a grease fire. Personal injury may
result. If a grease fire develops, turn knobs and LP tank
off.
• If grill has not been regularly cleaned, a grease fire can
occur that may damage the product. Pay close attention
while preheating or burning off food residue to insure
that a grease fire does not develop. Follow instructions
on General Grill Cleaning and Cleaning The Burner
Assembly to prevent grease fires.
• The best way to prevent grease fires is regular cleaning
of the grill.
NOTE: DO NOT over tighten screws and washers that
come into contact with porcelain coated surfaces. Over
tightening may cause the porcelain coating to crack and
break, resulting in exposed metal that will be prone to rust.
3
GRILLING GUIDE – Getting Started
First Time Use
Read your Assembly Manual and ensure the grill is put together
properly. Remove all Point-of-Purchase advertising material from
all grill surfaces before first use. We recommend operating your
grill on its highest setting for 15-20 minutes prior to your first use.
This aids in removing the oils used during manufacturing.
Lava Rock / Briquettes
This gas grill has been designed, engineered, and tested to be
used with flame tamers or heat distribution plates to provide
more even heating, improve the cleaning process, and reduce
flare-ups. The addition of after market lava rocks, charcoal, or
briquettes of any type will cause poor combustion and increase
the likelihood of a grease fire, and is not recommended. Using
briquettes, lava rock, or charcoal in this grill will void your
warranty. For extra smoke flavor, we recommend using a
smoker box with wood chips.
Temperature - Convective Grills ONLY.
The temperature gauge in the hood of your new grill measures
air temperature. The air temperature inside your grill will never
be as hot as the temperature at the cooking surface.
Note: Since 1995, all regulators (the part that attaches to the gas
tank to regulate the flow of gas) have included a safety feature
that restricts gas flow in the event of a gas leak. You can
inadvertently activate this safety feature without having a gas
leak. This typically occurs when you turn on the gas using the
grill control knob before you turn on the LP tank valve. If the gas
regulator safety feature activates, the grill will only reach
temperatures between 250°F and 300°F even with all burners on
the high setting.
Regulator
Coupling Nut
If your grill is not getting hotter than 250°F to 300°F these
steps should be taken first to reset the gas regulator safety
device:
1. Open the grill lid.
2. Turn off all knobs on the control panel in front.
3. Turn off the tank knob.
4. Disconnect the regulator from the LP tank.
5. Wait 30 seconds.
6. Reconnect the regulator to the LP tank.
7. Slowly open the LP tank knob all the way. Do not put
excessive force on the valve at the full open position to avoid
damaging the valve.
8. Turn on the appropriate control knob and light the grill per the
instructionsl.
An illustration of this process is included in this Product Guide.
See Troubleshooting section for additional information.
Pre-Heating Your Grill
Just like your home oven, your grill should be pre-heated to
provide optimum performance. Pre-heat the grill on high for 1015 minutes – longer if weather conditions require. Please refer to
the lighting instructions inside the Product Guide if you have
questions about how to light your grill. A match-light chain and
hole is provided for your convenience.
4
GRILLING GUIDE – Grilling 101
Outdoor grilling is really quite simple. You'll succeed with
burgers, dogs, or steaks usually on your very first try. With
experience, you will learn how to work with your grill, creating
more imaginative meals all the time. This knowledge makes up
the art of grilling. Before you start grilling, organize your food
according to cooking technique and required cooking time, and
optimize the use of your grilling area.
Rotisserie Cooking
Rotisserie cooking is best for 'round' meat, such as large roasts,
whole poultry, and pork. It generally requires an accessory motor
and spit rod that allows the meat to be turned at a constant
speed. Rotisserie cooking is best done in front of a special
rotisserie burner, or utilizing an indirect cooking burner
arrangement. A pan can be placed underneath the meat to catch
grease and food drippings, and helps minimize clean-up.
Direct Cooking
Direct cooking involves grilling your meat directly over high heat.
It is perfect for searing steaks, chops, and other smaller pieces of
meat and vegetables that quickly make their way to the table.
Indirect Cooking
Indirect cooking utilizes select burners to circulate heat
throughout the grill, without direct contact between the meat and
the flame. The meat is placed over the burner that is 'off'. This
method is generally used to slow cook large cuts of meat and
poultry. A pan can be placed underneath the meat to catch
grease and food drippings, and helps minimize clean-up.
Food Safety
Food safety is a very important part of enjoying the outdoor
cooking experience. To keep food safe from harmful bacteria,
follow these four basic steps:
Clean: Wash hands, utensils, and surfaces with hot soapy water
before and after handling raw meat.
Separate: Separate raw meats from ready-to-eat foods to avoid
cross contamination. Use a clean platter and utensils when
removing cooked foods.
Cook: Cook meat and poultry thoroughly to kill bacteria. Use a
thermometer to ensure proper internal food temperatures.
Chill: Refrigerate prepared foods and leftovers promptly.
5
GRILLING GUIDE – Tips & Tricks
Cooking on your new grill is a hands-on experience, and it is
recommended to remain outside with your grill while cooking.
Grilling can be affected by many external conditions. In cold
weather, you will need more heat to reach an ideal cooking
temperature, and grilling may take longer. The meat's internal
temperature and thickness can also affect cooking times. Cold
and thicker meats will take longer to cook.
Wood Chips
For extra smoke flavor when grilling, try adding wood chips.
Soak the chips in water for approximately 30 minutes before
adding to a smoke box or pan. Place smoke box or pan on top of
the cooking grate above the flame. Turn grill on high until the
wood starts to smoke. Reduce heat to desired temperature for
cooking, and place food on cooking grate as desired. Close lid to
retain more smoke. Hardwood varieties that work particularly
well with grilled foods include Alder, Apple, Cherry, Grapevines,
Hickory, Mesquite, Oak, Rosemary and Sassafras.
Internal Meat Temperatures
Meat cooked on a grill often browns very fast on the outside.
Therefore, use a meat thermometer to ensure it has reached
safe internal temperatures.
USDA Recommended Safe Minimum
Internal Temperatures
Beef, Veal, Lamb, Steak, Roasts, & Whole Pork
(with a 3 minute rest time)
145° F
Fish
Beef, Veal, Lamb, and Pork - Ground
Egg Dishes
Turkey, Chicken & Duck Whole, Pieces & Ground
145° F
160° F
160° F
165° F
Skewers
Metal skewers should be flat, with long handles. Round skewers
allow food to roll when turned, so it may not cook as evenly. Use
metal skewers when cooking meat kabobs. Wooden skewers
should be soaked in water for an hour before use, and are best
used for quick cooking foods such as vegetables and fruits.
Please refer to the USDA for complete, up-to-date information.
Our internal temperature chart is based on USDA standards for
meat doneness. Check it out at www.isitdoneyet.gov
Sauces
Sauces containing sugars and fats can cause flare-ups, and your
food may burn. In general, apply these sauces during the final
10 minutes of cooking. Keep in mind, use of excessive sauces
or glazes will also require extra cleaning afterwards.
Marinades and Rubs
To enhance the flavor of grilled foods, a liquid marinade or dry
rub can be used prior to cooking. Meat can be either soaked or
injected with liquid marinade up to 24 hours prior to grilling. Dry
rubs can be applied directly to the meat immediately before
grilling.
Utensils
Use tongs or a spatula to handle the food instead of a fork, and
don't turn the food too
often. Piercing the food
with a fork will release
juices that you want in
the meat, and may
cause flare-ups.
6
GRILLING GUIDE – Cleaning Your Grill
Why Clean?
We've all heard the saying 'An ounce of prevention is worth a
pound of cure'. This is great advice when it comes to keeping
your grill clean.
Routine Care
Periodic cleaning of this grill is necessary,
as grill fires can occur when grease and
food debris collect in the bottom of the grill.
After each use, remove any remaining
food particles from the cooking grate and
inside of the grill using a grill brush. Do
this after the grill has cooled down, yet is
still warm. It is much easier to clean food
particles while warmth is still present, than
after the food particles have completely
cooled and hardened. This grill is not
designed to be 'burned off' by closing the
lid and turning the burners on High for an
extended time. The excessive heat
generated can cause leftover grease to
catch fire, and can cause permanent
damage to your grill.
Cooking surfaces: If a bristle brush is used to clean any of the
grill cooking surfaces, ensure no loose bristles remain on cooking
surfaces prior to grilling. It is not recommended to clean cooking
surfaces while grill is hot.
Storing Your Grill
• Clean cooking grates.
• Store grill in dry location.
• When LP cylinder is connected to grill, store outdoors in a well
ventilated space and out of reach of children.
• Cover grill if stored outdoors. Choose from a variety of grill
covers offered by manufacturer.
• Store grill indoors ONLY if LP cylinder is turned off,
disconnected, and removed from grill. Never store LP cylinder
indoors.
• When removing grill from storage, follow the 'Cleaning the
Burner Assembly' instructions in the Use and Care section of
the Product Guide.
Critters
Spiders like to make their homes in the venturi tubes of grills.
These must be inspected and cleaned regularly to ensure there
are no blockages. Refer to the Use and Care portion of this
Product Guide for complete information.
General Cleaning
Plastic parts: Wash with warm soapy water and wipe dry. Do not
use abrasive cleaners, degreasers or a concentrated grill cleaner
on plastic parts. Damage to and failure of parts can result.
Porcelain surfaces: Because of glass-like composition, most
residue can be wiped away with baking soda/water solution or
glass cleaner. Use non-abrasive scouring powder for stubborn
stains.
Painted surfaces: Wash with mild detergent or non-abrasive
cleaner and warm water. Wipe dry with a soft non-abrasive cloth.
Stainless steel surfaces: Stainless steel can rust under certain
conditions. This can be caused by environmental conditions
such as chlorine or salt water, or improper
cleaning tools such as wire or steel
wool. It can also discolor due to heat,
chemicals, or grease build-up. To
maintain your grill's high quality
appearance, wash with mild detergent
and warm water, or use a stainless
steel grill cleaner. Baked-on grease
deposits may require the use of an
abrasive plastic cleaning pad. Use only
in direction of brushed finish to avoid
damage. Do not use abrasive pad on
areas with graphics.
The Char-Broil® grill is equipped with Gear Trax™, which
allow for the easy mounting of our unique line of Gear Trax
accessories. Please visit charbroil.com for a complete list
of Gear Trax accessories. *Available on most models.
VISIT CHARBROIL.COM FOR
ALL YOUR GRILLING NEEDS!
7
USE AND CARE
DANGER
• NEVER store a spare LP cylinder under or near
the appliance or in an enclosed area.
• Never fill a cylinder beyond 80% full.
• An over filled or improperly stored cylinder is a
hazard due to possible gas release from the
safety relief valve. This could cause an intense
fire with risk of property damage, serious injury or
death.
• If you see, smell or hear gas escaping,
immediately get away from the LP
cylinder/appliance and call your fire department.
LP Cylinder Removal, Transport and Storage
•Turn OFF all control knobs and LP cylinder valve. Turn coupling
nut counterclockwise by hand only - do not use tools to
disconnect. Loosen cylinder screw beneath bottom shelf or
disconnect other retention means, then lift PL cylinder up and
and out of cart. Install safety cap onto LP cylinder valve.
Always use cap and strap supplied with valve.
Failure to use safety cap as directed may result in serious
personal injury and/or property damage.
•A disconnected LP cylinder in LP Cylinder Valve
storage or being transported
must have a safety cap installed (as shown).
Do not store an LP cylinder in enclosed spaces
such as a carport, garage, porch, covered
Safety
patio or other building. Never leave an LP cylinder
Cap
inside a vehicle which may become overheated
Retainer Strap
by the sun.
•Do not store an LP cylinder in an area where children play.
8
LP Cylinder
•The LP cylinder used with your grill must meet the
following requirements:
•Use LP cylinders only with these required measurements: 12"
(30.5cm) (diameter) x 18" (45.7 cm) (tall) with 20 lb. (9 kg.)
capacity maximum.
•LP cylinders must be constructed and marked in accordance
with specifications for LP cylinders of the U.S. Department of
Transportation (DOT) or for Canada, CAN/CSA-B339,
cylinders, spheres and tubes for transportation of dangerous
goods. Transport Canada (TC). See LP cylinder collar for
marking.
•LP cylinder valve must have:
•Type 1 outlet compatible with
regulator or grill.
•Safety relief valve.
OPD Hand Wheel
•UL listed Overfill Protection
Device (OPD). This OPD safety
feature is identified by a unique triangular hand wheel. Use
only LP cylinders equipped with this type of valve.
•LP cylinder must be arranged for vapor withdrawal and include
collar to protect LP cylinder valve. Always keep LP cylinders in
upright position during use, transit or storage.
LP cylinder in upright position for vapor withdrawal
LP (Liquefied Petroleum Gas)
•LP gas is nontoxic, odorless and colorless when produced. For
Your Safety, LP gas has been given an odor (similar to rotten
cabbage) so that it can be smelled.
•LP gas is highly flammable and may ignite unexpectedly when
mixed with air.
LP Cylinder Filling
•Use only licensed and experienced dealers.
•LP dealer must purge new cylinder before filling.
•Dealer should NEVER fill LP cylinder more than 80% of LP
cylinder volume. Volume of propane in cylinder will vary by
temperature.
•A frosty regulator indicates gas overfill. Immediately close LP
cylinder valve and call local LP gas dealer for assistance.
•Do not release liquid propane (LP) gas into the atmosphere.
This is a hazardous practice.
•To remove gas from LP cylinder, contact an LP dealer or call a
local fire department for assistance. Check the telephone
directory under “Gas Companies” for nearest certified LP
dealers.
LP Cylinder Exchange
Connecting Regulator to the LP Cylinder
•Many retailers that sell grills offer you the option of replacing
your empty LP cylinder through an exchange service. Use only
those reputable exchange companies that inspect, precision fill,
test and certify their cylinders. Exchange your cylinder only
for an OPD safety feature-equipped cylinder as described
in the "LP Cylinder" section of this manual.
1.LP cylinder must be properly secured onto grill. (Refer to
assembly section.)
•Always keep new and exchanged LP cylinders in upright
position during use, transit or storage.
•Leak test new and exchanged LP cylinders BEFORE
connecting to grill.
•Place dust cap on cylinder valve outlet whenever the cylinder is
not in use. Only install the type of dust cap on the cylinder valve
outlet that is provided with the cylinder valve. Other types of caps
or plugs may result in leakage of propane.
4.Remove the protective cap from LP cylinder valve. Always use
cap and strap supplied with valve.
2.Turn all control knobs to the OFF position.
3.Turn LP cylinder OFF by turning hand-wheel clockwise to a
full stop.
Off
Clockwise
OPD Hand Wheel
LP Cylinder Leak Test
For your safety
•Leak test must be repeated each time LP cylinder is exchanged
or refilled.
•Do not smoke during leak test.
•Do not use an open flame to check for gas leaks.
•Grill must be leak tested outdoors in a well-ventilated area,
away from ignition sources such as gas fired or electrical
appliances. During leak test, keep grill away from open flames
or sparks.
•Use a clean paintbrush and a 50/50 mild soap and water
solution. Brush soapy solution onto areas indicated by arrows
in figure below.
▲ Do not use household cleaning agents. Damage to gas
train components can result.
Type 1 outlet with
thread on outside
Safety Relief Valve
Strap and Cap
Do not use a POL transport plug
(plastic part with external threads)!
It will defeat the safety feature of
the valve.
5.Hold regulator and insert nipple into LP
cylinder valve. Hand-tighten the
coupling nut, holding regulator in a
straight line with LP cylinder valve so
as not to cross-thread the connection.
Nipple has to be centered
into the LP cylinder valve.
WARNING
If “growing” bubbles appear do not use or move the LP
cylinder. Contact an LP gas supplier or your fire
department!
9
Leak Testing Valves, Hose and Regulator
1.Turn all grill control knobs to OFF.
2.Be sure regulator is tightly connected to LP cylinder.
Str
aig
ht
Hold coupling nut and regulator
as shown for proper connection
to LP cylinder valve.
3.Completely open LP cylinder valve by turning hand wheel
counterclockwise. If you hear a rushing sound, turn gas off
immediately. There is a major leak at the connection. Correct
before proceeding.
4.Brush soapy solution onto areas circled below, or other similar
fittings on your grill.
6.Turn the coupling nut clockwise and tighten to a full stop. The
regulator will seal on the back-check feature in the LP cylinder
valve, resulting in some resistance. An additional one-half to
three-quarters turn is required to complete the
connection. Tighten by hand only – do not use tools.
NOTE:
If you cannot complete the connection, disconnect regulator and
repeat steps 5 and 6. If you are still unable to complete the
connection, do not use this regulator!
DANGER
• Do not insert any tool or foreign object into the valve
outlet or safety relief valve. You may damage the valve
and cause a leak. Leaking propane may result in
explosion, fire, severe personal injury, or death.
WARNING
• Outdoor gas appliance is not intended to be installed
in or on a boat.
• Outdoor gas appliance is not intended to be installed
in or on an RV.
• Never attempt to attach this grill to the self-contained
LP gas system of a camper trailer or motor home.
• Do not use grill until leak-tested.
• If a leak is detected at any time, STOP and call the fire
department.
• If you cannot stop a gas leak, immediately close
LP cylinder valve and call LP gas supplier or your fire
department!
10
NOTE: Sideburner
shelf fascia not
shown for clarity.
NOTE: Your grill
may NOT be
equipped with a
sideburner.
5.If “growing” bubbles appear, there is a leak. Close LP
cylinder valve immediately and retighten connections. If leaks
cannot be stopped do not try to repair. Call for replacement
parts.
6.Always close LP cylinder valve after performing leak test by
turning hand wheel clockwise.
WARNING
For Safe Use of Your Grill and to Avoid Serious
Injury:
• Do not let children operate or play near grill.
• Keep grill area clear and free from materials that burn.
• Do not block holes in sides or back of grill.
• Check burner flames regularly.
• Use grill only in well-ventilated space. NEVER use in
enclosed space such as carport, garage, porch,
covered patio, or under an overhead structure of any
kind.
• Do not use charcoal or ceramic briquets in a gas grill.
(Unless briquets are supplied with your grill.)
• Do not cover grates with aluminum foil or any other
material. This will block burner ventilation and create
a potentially dangerous condition resulting in
property damage and/or personal injury.
• Use grill at least 3 ft. from any wall or surface.
Maintain 10 ft. clearance to objects that can catch fire
or sources of ignition such as pilot lights on water
heaters, live electrical appliances, etc.
Safety Tips
▲
Before opening LP cylinder valve, check the coupling nut for
tightness.
▲
When grill is not in use, turn off all control knobs and LP
cylinder valve.
Never move grill while in operation or still hot.
▲
▲
▲
▲
Use long-handled barbecue utensils and oven mitts to avoid
burns and splatters.
Maximum load for sideburner and side shelf is 10 lbs.
The grease tray or cup must be installed during use and
emptied after each use. Do not remove grease tray or cup
until grill has completely cooled.
▲ Clean grill often, preferably after each cookout. If a bristle
brush is used to clean any of the grill cooking surfaces,
ensure no loose bristles remain on cooking surfaces prior to
grilling. It is not recommended to clean cooking surfaces
while grill is hot.
▲
▲
▲
If you notice grease or other hot material dripping from grill
onto valve, hose or regulator, turn off gas supply at once.
Determine the cause, correct it, then clean and inspect valve,
hose and regulator before continuing. Perform a leak test.
Keep ventilation openings in cylinder enclosure (grill cart) free
and clear of debris.
Do not store objects or materials inside the grill cart
enclosure that would block the flow of combustion air to the
underside of either the control panel or the firebox bowl.
▲
The regulator may make a humming or whistling noise during
operation. This will not affect safety or use of grill.
▲
▲
If you have a grill problem see the "Troubleshooting Section".
If the regulator frosts, turn off grill and LP cylinder valve
immediately. This indicates a problem with the cylinder and it
should not be used on any product. Return to supplier!
Ignitor Lighting
▲
• Apartment Dwellers:
Check with management to learn the requirements
and fire codes for using an LP gas grill in your
apartment complex. If allowed, use outside on the
ground floor with a three (3) foot clearance from walls
or rails. Do not use on or under balconies.
• NEVER attempt to light burner with lid closed. A
buildup of non-ignited gas inside a closed grill is
hazardous.
• Never operate grill with LP cylinder out of correct
position specified in assembly instructions.
• Always close LP cylinder valve and remove
coupling nut before moving LP cylinder from
specified operation position.
Do not lean over grill while lighting.
OFF gas burner control valves.
1. Turn
2. Turn ON gas at LP cylinder.
3. Open lid during lighting.
HIGH.
4. To ignite, push and turn ignition burner knob to
5. .Push and hold ELECTRONIC IGNITION button until the burner
lights.
6. If ignition does NOT occur in 5 seconds, turn the burner
controls
OFF, wait 5 minutes and repeat the lighting
procedure.
7. To ignite remaining burners, turn knob to the HIGH position
starting with the burners closest to IGNITION BURNERS first.
If ignitor does not work, follow match lighting instructions.
8. For grills equipped with ELECTRONIC IGNITION at
each burner:
Repeat steps 4 through 6 to light each burner.
9. Once each burner has ignited, turn knobs to desired setting.
11
Burner Flame Check
WARNING
Turn controls and gas source or tank OFF when not
in use.
• Remove cooking grates and flame tamers. Light burners, rotate
knobs from HIGH to LOW. You should see a smaller flame in
LOW position than seen on HIGH. Perform burner flame check
on sideburner, also. Always check flame prior to each use. If
only low flame is seen refer to "Sudden drop or low flame" in
the Troubleshooting Section.
HIGH
CAUTION
If ignition does NOT occur in 5 seconds, turn the
burner controls OFF, wait 5 minutes and repeat the
lighting procedure. If the burner does not ignite with
the valve open, gas will continue to flow out of the
burner and could accidently ignite with risk of injury.
Match-Lighting
▲ Do not lean over grill while lighting.
1. Open lid. Turn ON gas at LP cylinder.
2. Place match into match holder (hanging from side panel of
grill). Light match; then light burner by placing match through
the match light hole on right or left side of grill.
3. Push in and turn far right or far left burner knob to the HIGH
position, depending on match light hole selected. Be sure
burner lights and stays lit.
4. Light adjacent burners in sequence by pushing knobs in and
turning to the HIGH position.
LOW
Turning Grill Off
• Turn all knobs to the OFF position. Turn LP cylinder OFF by
turning hand-wheel clockwise to a full stop.
Ignitor Check
• Turn gas off at LP cylinder. Press and hold electronic ignitor
button. "Click" should be heard and spark seen each time
between each collector box or burner and electrode. See
"Troubleshooting" if no click or spark.
Valve Check
• Important: Make sure gas is off at LP cylinder before
checking valves. Knobs lock in OFF position. To check
valves, first push in knobs and release, knobs should spring
back. If knobs do not spring back, replace valve assembly
before using grill. Turn knobs to LOW position then turn back to
OFF position. Valves should turn smoothly.
Hose Check
• Before each use, check to see if hoses are cut or worn or kinked.
Replace damaged hoses before using grill. Use only
valve/hose/regulator specified by manufacturer.
General Grill Cleaning
NOTE: Your grill may NOT be equipped with a Sideburner!
Sideburner Ignitor Lighting
▲
Do not lean over grill while lighting.
1. Open sideburner lid. Turn ON gas at LP cylinder.
2. Turn sideburner knob to the HIGH position, push and hold
ELECTRONIC IGNITOR button.
3. If sideburner does NOT light within 5 seconds, turn knob to
OFF, wait 5 minutes, then
repeat lighting procedure.
Sideburner Match Lighting
1. Open sideburner lid. Turn ON
gas at LP cylinder.
2. Place lit match near burner.
3. Turn sideburner knob to the
HIGH position.
Be sure burner lights and
stays lit.
12
• Do not mistake brown or black accumulation of grease and
smoke for paint. Interiors of gas grills are not painted at the
factory (and should never be painted). Apply a strong solution
of detergent and water or use a grill cleaner with scrub brush
on insides of grill lid and bottom. Rinse and allow to completely
air dry. Do not apply a caustic grill/oven cleaner to painted
surfaces.
• Plastic parts: Wash with warm soapy water and wipe dry.
▲ Do not use citrisol, abrasive cleaners, degreasers or a
concentrated grill cleaner on plastic parts. Damage to and
failure of parts can result.
• Porcelain surfaces: Because of glass-like composition, most
residue can be wiped away with baking soda/water solution or
specially formulated cleaner. Use nonabrasive scouring powder
for stubborn stains.
• Painted surfaces: Wash with mild detergent or nonabrasive
cleaner and warm soapy water. Wipe dry with a soft
nonabrasive cloth.
• Stainless steel surfaces: To maintain your grill’s high quality
appearance, wash with mild detergent and warm soapy water
and wipe dry with a soft cloth after each use. Baked-on grease
deposits may require the use of an abrasive plastic cleaning
pad. Use only in direction of brushed finish to avoid damage.
Do not use abrasive pad on areas with graphics.
• Cooking surfaces: If a bristle brush is used to clean any of
the grill cooking surfaces, ensure no loose bristles remain on
cooking surfaces prior to grilling. It is not recommended to
clean cooking surfaces while grill is hot.
CAUTION
SPIDER ALERT!
SPIDER AND WEBS
INSIDE BURNER
If your barbeque is getting hard to light or
the flame is weak, check and clean the
venturis and burners.
3. Remove carryover tubes and burners.
4. Detach electrode from burner.
NOTE: Removal/Detachment method will depend on the
burner configuration. See different configurations in
illustrations below.
5. Carefully lift each burner up and away from valve openings.
We suggest three ways to clean the burner tubes. Use the one
easiest for you.
(A) Bend a stiff wire (a light weight coat hanger works well)
into a small hook. Run the hook through each burner
tube several times.
(B) Use a narrow bottle brush with a flexible handle (do not
use a brass wire brush), run the brush through each
burner tube several times.
(C) Wear eye protection: Use an air hose to force air into
the burner tube and out the burner ports. Check each
port to make sure air comes out each hole.
6. Wire brush entire outer surface of burner to remove food
residue and dirt.
7. Clean any blocked ports with a stiff wire such as an open
paper clip.
8. Check burner for damage, due to normal wear and corrosion
some holes may become enlarged. If any large cracks or
holes are found replace burner.
VERY IMPORTANT: Burner tubes must reengage valve
openings. See illustrations at right.
Correct
9. Attach electrode to burner.
burner-to-valve
10. Carefully replace burners.
engagement
11. Attach burners to brackets on firebox.
12. Reposition carryover tubes and attach
to burners. Replace flame tamers and
cooking grates.
Remove screws
x
ebo
Fir
e
tub
rr
Storing Your Grill
• Clean cooking grates.
• Store in dry location.
• When LP cylinder is connected to grill, store outdoors in a wellventilated space and out of reach of children.
• Cover grill if stored outdoors. Choose from a variety of grill
covers offered by manufacturers.
• Store grill indoors ONLY if LP cylinder is turned off and
disconnected, removed from grill and stored outdoors.
• When removing grill from storage, follow “Cleaning the Burner
Assembly” instructions before starting grill.
er
yov
Ca
Firebox
burner
bracket
Electrode
x
Firebo
Electrode
er tube
Carryov
Cleaning the Burner Assembly
Follow these instructions to clean and/or replace parts of burner
assembly or if you have trouble igniting grill.
1. Turn gas OFF at control knobs and LP cylinder.
2. Remove cooking grates and flame tamers.
Firebox burner
bracket
Pry off
electrode with
a flat blade
screwdriver
13
LIMITED WARRANTY
This warranty only applies to units purchased from an authorized retailer. Manufacturer warrants to the original consumer-purchaser only that this
product shall be free from defects in workmanship and materials after correct assembly and under normal and reasonable home use for the periods
indicated below beginning on the date of purchase*. The manufacturer reserves the right to require that defective parts be returned, postage and or
freight pre-paid by the consumer for review and examination.
SCOPE OF COVERAGE
Stainless Burner
Firebox and Lid
All Other Parts
PERIOD OF COVERAGE
5 years from date of purchase*
2 years from date of purchase*
1 year from date of purchase*
TYPE OF FAILURE COVERAGE
PERFORATION, MANUFACTURING,
AND MATERIAL DEFECTS ONLY
*Note: A dated sales receipt WILL be required for warranty service.
The original consumer-purchaser will be responsible for all shipping charges for parts replaced under the terms of this limited warranty.
This limited warranty is applicable in the United States and Canada only, is only available to the original owner of the product and is not transferable.
Manufacturer requires proof of your date of purchase. Therefore, you should retain your sales slip or invoice. Registering your product is not a
substitute for proof of purchase and the manufacturer is not responsible for or required to retain proof of purchase records.
This limited warranty applies to the functionality of the product ONLY and does not cover cosmetic issues such as scratches, dents, corrosions or
discoloring by heat, abrasive and chemical cleaners or any tools used in the assembly or installation of the appliance, surface rust, or the
discoloration of stainless steel surfaces. RUST is not considered a manufacturing or materials defect.
This limited warranty will not reimburse you for the cost of any inconvenience, food, personal injury or property damage.
ITEMS MANUFACTURER WILL NOT PAY FOR:
1. Shipping cost, standard or expedited, for warranty and replacement parts
2. Service calls to your home.
3. Repairs when your product is used for other than normal, single-family household or residential use.
4. Damage, failures, or operating difficulties resulting from accident, alteration, careless handling, misuse, abuse, fire, flood,
acts of God, improper installation or maintenance, installation not in accordance with electrical or plumbing codes, or use
of products not approved by the manufacturer.
5. Any food loss due to product failures or operating difficulties.
6. Replacement parts or repair labor costs for units operated outside the United States or Canada.
7. Pickup and delivery of your product.
8. Repairs to parts or systems resulting from unauthorized modifications made to the product.
9. The removal and/or reinstallation of your product.
DISCLAIMER OF IMPLIED WARRANTIES and LIMITATION OF REMEDIES
Repair or replacement of defective parts is your exclusive remedy under the terms of this limited warranty. In the event of parts availability issues,
the manufacturer reserves the right to substitute like or similar parts that are equally functional.
Manufacturer will not be responsible for any consequential or incidental damages arising from the breach of either this limited warranty or any
applicable implied warranty, or for failure or damage resulting from acts of God, improper care and maintenance, grease fire, accident, alteration,
replacement of parts by anyone other than Manufacturer, misuse, transportation, commercial use, abuse, hostile environments (inclement weather,
acts of nature, animal tampering), improper installation or installation not in accordance with local codes or printed manufacturer instructions.
THIS LIMITED WARRANTY IS THE SOLE EXPRESS WARRANTY GIVEN BY THE MANUFACTURER. NO PRODUCT PERFORMANCE
SPECIFICATION OR DESCRIPTION WHEREVER APPEARING IS WARRANTED BY MANUFACTURER EXCEPT TO THE EXTENT SET
FORTH IN THIS LIMITED WARRANTY. ANY IMPLIED WARRANTY PROTECTION ARISING UNDER THE LAWS OF ANY STATE,
INCLUDING IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR USE, IS HEREBY
LIMITED IN DURATION TO THE DURATION OF THIS LIMITED WARRANTY.
Neither dealers nor the retail establishment selling this product has any authority to make any additional warranties or to promise remedies
in addition to or inconsistent with those stated above. Manufacturer's maximum liability, in any event, shall not exceed the purchase price of the
product paid by the original consumer.
NOTE: Some states do not allow an exclusion or limitation of incidental or consequential damages, so some of the above limitations or exclusions
may not apply to you. This limited warranty gives you specific legal rights as set foth herein. You may also have other rights which vary from state
to state. In the state of California only, if refinishing or replacement of the product is not commercially practicable, the retailer selling this product or
the Manufacturer will refund the purchase price paid for the product, less the amount directly attributable to use by the original consumer-purchaser
prior to discovery of the nonconformity. In addition, in the state of California only, you may take the product to the retail establishment selling this
product in order to obtain performance under this limited warranty.
If you wish to obtain performance of any obligation under this limited warranty, you should
write to:
Consumer Relations
P. O. Box 1240
Columbus, GA 31902-1240
Consumer returns will not be accepted unless a valid Return Authorization is first acquired. Authorized returns are clearly marked on the outside of
the package with an RA number and the package is shipped freight/postage pre-paid. Consumer returns that do not meet these standards will be
refused.
14
PARTS LIST
Key
Qty Description
A
1
FIREBOX
B
1
C
3
D
Key
Qty Description
MM
1
BACK RAIL
TUBE BURNER, F/ ELECTRODE
NN
1
CART, RIGHT SIDE
TUBE BURNER
OO
1
SHIELD, F/ TANK
1
ELECTRODE, MAIN BURNER
PP
1
GREASE TRAY
E
3
CARRY OVER TUBE
QQ
1
AXLE ROD
F
4
HEAT TENT
RR
2
WHEEL
G
2
COOKING GRATE
SS
1
GREASE CUP
H
1
WARMING GRID
TT
1
CLIP, F/ GREASE CUP
I
1
GRILL LID
UU
2
LEG EXTENDER
J
1
LOGO PLATE
VV
1
BUTTON, F/ ELECTRONIC MODULE
K
1
TEMPERATURE GAUGE
WW
1
SIDEBURNER BRACE
L
1
BEZEL, F/ TEMPERATURE GAUGE
XX
1
HEAT SHIELD, F/ EI MODULE
M
4
SILICONE RUBBER BUMPER, SMALL
YY
2
SILICONE RUBBER BUMPER, LARGE
ZZ
4
SIDE SHELF TOWEL BAR ENDCAP
N
1
GRILL LID HANDLE
O
1
TOP LID HARDWARE
P
1
CONTROL PANEL, MAIN
Q
1
ELECTRONIC MODULE, W/ BUTTON
…
1
HARDWARE PACK
R
1
VALVE/ HOSE/ REGULATOR
…
1
ASSEMBLY MANUAL, ENGLISH
S
4
BEZEL F/ KNOB
…
1
ASSEMBLY MANUAL, SPANISH
T
4
CONTROL KNOB
U
1
BEZEL F/ KNOB, SB
V
1
CONTROL KNOB, SB
W
1
MATCH HOLDER
X
1
LEFT SIDE SHELF
Y
2
SIDE SHELF TOWEL BAR
Z
1
RIGHT SIDE SHELF
AA
1
DRIP PAN F/ SIDEBURNER
BB
1
SIDEBURNER
CC
1
ELECTRODE, F/ SB
DD
1
ELECTRODE WIRE, SIDEBURNER
EE
1
SIDEBURNER GRATE
FF
1
SIDEBURNER LID
GG
1
CART, LEFT SIDE
HH
2
BOTTOM SHELF BRACE
II
1
BOTTOM SHELF
JJ
1
TANK RETAINER WIRE
KK
1
UPPER FRONT PANEL, W/O PIN
LL
1
LOWER FRONT PANEL, W/ PIN
NOT Pictured
NOTE: Some grill parts shown in the assembly steps may differ slightly in appearance from
those on your particular grill model. However, the method of assembly remains the same.
15
PARTS DIAGRAM
O
H
I
G
G
FF
L
K
J
E
E
E
EE
F
F
F
F
M
CC
M
C
B
C
C
N
BB
AA
D
YY
A
Z
DD
X
YY
WW
ZZ
P
W
ZZ
Y
ZZ
Y
S
V
U
S
S
S
T
T
T
T
TT
VV
Q
PP
R
SS
NN
XX
GG
MM
OO
II
HH
RR
KK
LL
UU
QQ
16
JJ
HH
RR
ASSEMBLY
ASSEMBLY
1
CAUTION: When unpacking grill components, two people should raise grill head from the shipping box.
Take the leg assembly out from the shipping box, place it as shown.
Front
Right Leg Assembly
2
Rear
Left Leg Assembly
Place bottom shelf to bottom shelf brace.
Tighten the pre-installed screws to bottom shelf.
Bottom Shelf
17
3
Place lower front panel(with pin) to cart.
Tighten the pre-installed screws to the cart.
Place upper front panel(without pin) to cart like lower front panel. Make sure the hole on upper front panel is fit to the pin on lower
front panel.
Tighten the pre-installed screws to the cart.
Lower Front Panel
Pin
Upper Front Panel
18
4
Turn leg assembly upside down.
Insert axle rod through wheel, wheel spacer, legs, other wheel spacer and wheel. Be sure to face “cone” side of
wheel against leg. Attach with (1) axle washer and hitch pin.
Insert leg extenders into right legs. Then turn cart upright and press leg extender into place with body weight.
Wheel
1” Hitch Pin
Qty. 1
Wheel Spacer
Wheel Spacer
Qty: 2
Leg Extender
Axle Washer
Qty: 1
"Cone" side of wheel against leg
Axle Washer
Wheel Spacer
5
Hitch Pin
Place back rail to the cart.
Tighten the pre-installed screws to the cart.
Back Rail
19
6
Place heat shield to cart back brace.
Tighten the pre-installed screws to the cart back brace.
Heat Shield, F/Tank
7
Place grease tray to the cart assembly as shown.
Insert tank retainer to the holes from the bottom shelf.
Grease Tray
Tank Retainer, Wire Form
20
8
This step requires two people to lift and position grill head onto cart.
Carefully lower the grill head onto the cart. Make sure the regulator is placed between grease tray and front panel.
Slide the grill head back until the pre-installed screws fit completely into the slots of cart brackets. Tighten the pre-installed screws to
the fire box.
Grill Head
Pre-installed
Screw
Front Panel
Grease Tray
Cart Bracket
Regulator
9
Place right side shelf to the right side of firebox.
Tighten the pre-installed screws to the right side shelf.
Right Side Shelf
Tighten the pre-installed
screws
21
10
Place left side shelf to the left side of firebox (A).
Tighten the pre-installed screws to the left side shelf (B).
Remove the nut from injecter, insert the injecter to the hole on the sideburner brace, re-install and tighten the nut to fix the injecter to
sideburner brace (C).
Remove the screws, lock washers and flat washers from sideburner. Place sideburner into shelf. Make sure injecter is inside
sideburner tube. Attach sideburner to drip pan with the screws, lock washers and flat washers removed from sideburner previously.
Attach sideburner ignitor wire to the electronic ignition module through the hole of the left plate of control panel (D).
Place grate onto sideburner shelf (E).
A
Left Side Shelf
B
Tighten the
pre-installed
screws
C
D
Sideburner Brace
Sideburner Tube
Nut
Injecter
E
Sideburner
Grate
Sideburner Ignitor Wire
Electronic Ignition Module
Sideburner Ignitor Wire
22
Place heat tents over burners as shown.
12
Place cooking grates onto grate rests.
Place warming grid onto the top of the firebox. Vertical legs insert into the slots on the upper ledge of the firebox.
Unscrew ignitor cap and place AAA battery into slot with positive end (+) facing outward. Screw ignitor cap onto ignitor.
He
11
at
nt
Te
He
at
Ten
t
Warming Grid
Cooking Grate
Slot
AAA Battery
23
13
Hang grease cup clip from bottom of grease tray and place grease cup into grease cup clip.
Grease Cup Clip
Grease Cup
CAUTION
Failure to install grease cup clip and cup
will cause hot grease to drip from bottom
of grill with risk of fire or property damage.
14
LP tank is sold separately. Use only with an OPD (over-fill protection device) equipped LP tank. Fill and leak check before attaching
to grill and regulator.
Place LP tank into hole in bottom shelf, make sure tank valve is facing the front of the grill. Then place tank retainer as shown to
hold LP tank securely in place.
See Use and Care section to correctly Leak Test and
perform the Burner Flame Check.
CAUTION
• Failure to install tank correctly may allow gas hose to
be damaged in operation, resulting in the risk of fire.
Regulator
LP Tank
24
DANGER: If a gas leak cannot be stopped, or a fire occurs due to gas leakage, call the fire department.
Emergencies
Possible Cause
Prevention/Solution
Gas leaking from
cracked/cut/burned
hose.
• Damaged hose.
• Turn off gas at LP cylinder or at source on natural gas systems. If
anything but burned, replace valve/hose/regulator. If burned,
discontinue use of product until a plumber has investigated cause
and corrections are made.
Gas leaking from LP
cylinder.
• Mechanical failure due to rusting or
mishandling.
• Replace LP cylinder.
Gas leaking from LP
cylinder valve.
• Failure of cylinder valve from
mishandling or mechanical failure.
• Turn off LP cylinder valve. Return LP cylinder to gas supplier.
Gas leaking between
LP cylinder and
regulator connection.
• Improper installation, connection not
tight, failure of rubber seal.
• Turn off LP cylinder valve. Remove regulator from cylinder and
visually inspect rubber seal for damage. See LP Cylinder Leak Test
and Connecting Regulator to the LP Cylinder.
Fire coming through
control panel.
• Fire in burner tube section of burner due
to blockage.
• Turn off control knobs and LP cylinder valve. Leave lid open to
allow flames to die down. After fire is out and grill is cold, remove
burner and inspect for spider nests or rust. See Natural Hazard
and Cleaning the Burner Assembly pages.
Grease fire or
continuous excessive
flames above cooking
surface.
• Too much grease buildup in burner area.
• Turn off control knobs and LP cylinder valve. Leave lid open to
allow flames to die down. After cooling, clean food particles and
excess grease from inside firebox area, grease tray, and other
surfaces.
Possible Cause
Prevention/Solution
GAS ISSUES:
• Trying to light wrong burner.
• See instructions on control panel and in Use and Care section.
• Burner not engaged with control valve.
• Make sure valves are positioned inside of burner tubes.
• Obstruction in burner.
• Ensure burner tubes are not obstructed with spider webs or other
matter. See cleaning section of Use and Care.
• No gas flow.
• Make sure LP cylinder is not empty. If LP cylinder is not empty,
refer to “Sudden drop in gas flow.”
• For a grill equipped with the AUTO-CLEAN™ feature, make sure
the AUTO-CLEAN™ valve is set to “Grill”
• Vapor lock at coupling nut to LP cylinder.
• Turn off knobs and disconnect coupling nut from LP cylinder.
Reconnect and retry.
• Coupling nut and LP cylinder valve not
fully connected.
• Turn the coupling nut approximately one-half to three-quarters
additional turn until solid stop. Tighten by hand only - do not use
tools.
Troubleshooting
Problem
Burner(s) will not light
using ignitor.
(See Electronic Ignition
Troubleshooting also)
Continued on next
page.
ELECTRICAL ISSUES:
• Electrode cracked or broken; “sparks at
crack.”
• Replace electrode(s).
• Electrode tip not in proper position.
Main Burners:
• Tip of electrode should be pointing toward gas port opening on
burner. The distance should be 1/8” to 1/4”. Adjust if necessary.
Sideburner:
• Tip of electrode should be pointing toward gas port opening on
burner. the distance should be 1/8” to 3/16”. Adjust if necessary.
• Wire and/or electrode covered with
cooking residue.
• Clean wire and/or electrode with rubbing alcohol and clean swab.
• Wires are loose or disconnected.
• Reconnect wires or replace electrode/wire assembly.
• Wires are shorting (sparking) between
ignitor and electrode.
• Replace ignitor wire/electrode assembly.
• Dead battery.
• Replace with a new alkaline battery.
25
Troubleshooting (continued)
Problem
Possible Cause
Prevention/Solution
Burner(s) will not light
using ignitor.
(See Electronic Ignition
Troubleshooting also)
ELECTRONIC IGNITION:
• No spark, no ignition noise.
• See Section I of Electronic Ignition System.
• No spark, some ignition noise.
• See Section II of Electronic Ignition System.
• Sparks, but not at electrode or at full
strength.
• See Section III of Electronic Ignition System.
Burner(s) will not
match light.
• See “GAS ISSUES:” on previous page.
• Match will not reach.
• Use long-stem match (fireplace match).
• Improper method of match-lighting.
• Out of gas.
• See “Match-Lighting” section of Use and Care.
• Check for gas in LP cylinder.
• Excess flow valve tripped.
• Turn off knobs, wait 30 seconds and light grill. If flames are still low,
turn off knobs and LP cylinder valve. Disconnect regulator.
Reconnect regulator and leak-test. Turn on LP cylinder valve, wait
30 seconds and then light grill.
• Vapor lock at coupling nut/LP cylinder
connection.
• Turn off knobs and LP cylinder valve. Disconnect coupling nut from
cylinder. Reconnect and retry.
• High or gusting winds.
• Turn front of grill to face wind or increase flame height.
• Low on LP gas.
• Refill LP cylinder.
• Excess flow valve tripped.
• Refer to “Sudden drop in gas flow” above.
• Grease buildup.
• Clean burners and inside of grill/firebox.
• Excessive fat in meat.
• Trim fat from meat before grilling.
• Excessive cooking temperature.
• Adjust (lower) temperature accordingly.
Persistent grease fire.
• Grease trapped by food buildup around
burner system.
• Turn knobs to OFF. Turn gas off at LP cylinder. Leave lid in position
and let fire burn out. After grill cools, remove and clean all parts.
Flashback...
(fire in burner tube(s)).
• Burner and/or burner tubes are blocked.
• Turn knobs to OFF. Clean burner and/or burner tubes. See burner
cleaning section of Use and Care.
Unable to fill LP
cylinder.
• Some dealers have older fill nozzles
with worn threads.
• The worn nozzles don’t have enough “bite” to engage the valve. Try
a second LP dealer.
One burner does not
light from other
burner(s).
• Grease buildup or food particles in
end(s) of carryover tube(s).
• Clean carry-over tube(s) with wire brush.
AUTO-CLEAN™
Possible Cause
Prevention/Solution
Sudden drop in gas
flow or low flame.
Flames blow out.
Flare-up.
(If Equipped)
Timer does not work
(Green light does not
flash)



Dead Battery
Batteries installed incorrectly.
Knob Position did not start the Clean
Cycle



Replace batteries
Install batteries correctly.
Push Knob in to start the clean cycle. (Green LED should begin to
flash)
No LED’s will illuminate

Dead Battery

Replace batteries
Red LED next to battery
symbol is illuminated

Low Battery Strength

Prepare to replace batteries (NOTE: Clean cycle will operate with
a weak battery.
26
Troubleshooting - Electronic Ignition
Problem (Ignition)
Check Procedure
Prevention/Solution
• Check battery orientation.
• Install battery (make sure that “+” and “–”
connectors are oriented correctly, with “+” end up
and “–” end down.)
• Has battery been used
previously?
• Replace battery with new alkaline battery.
• Button assembly not
installed properly.
• Check to insure threads are
properly engaged. Button
should travel up and down
without binding.
• Unscrew button cap assembly and reinstall, making
sure threads are aligned and engaged fully.
• Faulty spark module.
• If no sparks are generated
with new battery and good
wire connections, module is
faulty.
• Replace spark module assembly.
• Are output connections on
and tight?
• Remove and reconnect all output connections at
module and electrodes.
• Output lead
connections not
connected.
• Are output connections on
and tight?
• Remove and reconnect all output connections at
module and electrodes.
• Arcing to grill away
from burner(s).
• If possible, observe grill in
dark location. Operate
ignition system and look for
arcing between output wires
and grill frame.
• If sparks are observed other than from burner(s),
wire insulation may be damaged. Replace wires.
• Weak battery.
• All sparks present but weak
or at slow rate.
• Replace battery with a new alkaline battery.
• Electrodes are wet.
• Has moisture accumulated
on electrode and/or in burner
ports?
• Use paper towel to remove moisture.
• Electrodes cracked or
broken “sparks at
crack”.
• Inspect electrodes for
cracks.
• Replace cracked or broken electrodes.
Possible Cause
SECTION I
• Battery not installed
No sparks appear at
properly.
any electrodes when
Electronic Ignition Button
is pressed; no noise can
• Dead battery.
be heard from spark
module.
SECTION II
• Output lead
No sparks appear at
connections not
any electrodes when
Electronic Ignition Button connected.
is pressed; noise can
be heard from spark
module.
SECTION III
Sparks are present
but not at all
electrodes and/or not
at full strength
27
NOTES
28
NOTES
29
NOTES
30
Please register your product online at:
Registre su producto en línea en:
Veuillez enregistrer votre produit à l'adresse:
www.charbroil.com/register
(If you register online, you do not need to send in this registration card.)
(Si registra en línea, no es necesario enviar esta tarjeta de registro.)
(Si vous enregistrez votre produit en ligne, il n'est pas nécessaire d'envoyer la carte
d'enregistrement.)
PLEASE FILL OUT THIS CARD AND ATTACH A COPY OF YOUR SALES RECEIPT. RETURN IT WITHIN10 DAYS OF PURCHASE.FOR WARRANTYSERVICEPROOF OF PURCHASE
WILL BE REQUIRED.THIS WARRANTYIS NON‐TRANSFERABLE.
LLENE ESTA TARJETA Y DEVUELVALADENTRO DE LOS 10 DIAS DE LA COMPRA.PARA EL SERVICIODE GARANTIAES NECESARIOQUE PRESENTESU COMPROBANTEDE
COMPRA.CONSERVELA FACTURA.ESTA GARANTIAES INTRANSFERIBLE.
VEUILLEZCOMPLETERCETTE CARTE ET LA RETOURNERDANS LES 10 JOURS SUIVANTL’ACHAT. POUR OBTENIRLE SERVICESOUS GARANTIE,UNE PREUVED’ACHAT DOIT
ETRE PRESENTEE.VEUILLEZCONSERVERVOTRE FACTURE. LA PRESENTEGARANTIEN’EST PAS TRANSFERABLE.
~ PLEASE PRINT ~ IMPRIMAPOR FAVOR ~ S'IL VOUS PLAÎT IMPRIMER~
*Required | Necesario | Exigé
*❶ First Name | Nombre | Prénom
Initial | Inicial | Initiale
Last Name | Apellido | Nom de Famillie
Address (number & street) | Dirección (número y calle) | Adresse (numéro et rue)
Apt Number | Nº de apart | Nº d’appt.
City | Cludad | Ville
Zip Code | Código Zip | Code Postal
State | Estado | Province
*❷ E‐mail Address | Dirección de correo electrónico | Adresse électronique
* ❸ Phone Number | Número telefónico | Numéro de téléphone
*❹ Model Number | Número de modelo | Numéro de modèle
STICKERON PRODUCT
Serial Number | Número de serie| Numéro de série
❻
Date of Purchase | Fecha de compra | Date de l’achat
❼
Store Name | Nombre de la tienda | Nom du magasin
$
❽
Purchase Price | Precio de compra | Prix d’achat
❾
Your Gender | Sexo | Sexe:
 Male | Masculino | Masculin
 Female | Femenino | Féminin
❿
1.
2.
3.
4.
5.
6.
Which product are you registering?
¿Qué producto está registrando?
Quel produit enregistrez‐vous?
 Gas Grill | Parrilla a gas | Gril au gaz
 Electric Grill | Parrilla eléctrica | Gril électrique
 Smoker | Ahumador | Fumoir
 Charcoal Grill | Parrilla a carbón | Barbecue au charbon
 Cooker/Fryer | Cocina/freidora | Cuiseur/Friteuse
 Other | Otro | Autre
*❺Attachcopyofyour
salesreceipthere.
Adjunteaquilacopia
desurecibode
compra
Veuillezattacherune
copiedevotrereçu
ici.
Mail to: / Enviar a: / Envoyer à :
Char‐Broil Warranty Registration
P.O. Box 1240
Columbus, GA 31902‐1240
We respect your privacy. | Respetamos su privacidad. | Nous respectons votre vie privée.



If you prefer not to receive special offers and promotions from Char‐Broil, please check here:
Marque aquí si no desea recibir ofertas y promociones especiales de Char‐Broil:
Si vous préférez ne pas recevoir d’informations concernant des offres spéciales et des
promotions de Charbroil, veuillez cocher ici:
Thank you for completing this questionnaire. | Gracias por completer este cuestionario. | Merci d’avoir bien voulu remplir ce questionnaire.
31
THANK YOU
FOR YOUR RECENT
PURCHASE FROM
CHECK OUT THESE
GREAT FEATURES
ON OUR WEBSITE
•
Valuable product information
•
Inspiring grilling accessories
•
Reliable customer support
•
Delicious recipes and tips from chefs
•
Exciting events and promotions
•
And much more!
REGISTER YOUR PRODUCT TO RECEIVE A
SPECIAL OFFER
CHARBROIL.COM/REGISTER