2016 Nissan GT-R Owner`s Manual

Transcription

2016 Nissan GT-R Owner`s Manual
2016 NISSAN GT-R
R35-D
R35-D
Printing: December 2014 (20)
Publication No.: OM16E0 0R35U0
Printed in U.S.A.
2016
OWNER’S MANUAL
For your safety, read carefully and keep in this vehicle.
(3,1)
FOREWORD
Welcome to the growing family of new NISSAN
owners. This vehicle is delivered to you with
confidence. It was produced using the latest
techniques and strict quality control.
This manual was prepared to help you understand the operation and maintenance of your
vehicle so that you may enjoy many miles
(kilometers) of driving pleasure. Please read
through this manual before operating your
vehicle.
A separate Warranty Information Booklet
contains the warranties covering your
vehicle (whose terms have control over
this Owner’s Manual or any other document or representation regarding warranty
coverage). The “NISSAN GT-R Service and
Maintenance Guide” explains details
about maintaining and servicing your vehicle.
Additionally, a separate Customer Care/
Lemon Law Booklet (U.S. only) will explain
how to resolve any concerns you may have
with your vehicle, as well as clarify your
rights under your state’s lemon law.
In addition to factory installed options, your
vehicle may also be equipped with additional
accessories installed by NISSAN or your GT-R
certified NISSAN dealer prior to delivery. It is
important that you familiarize yourself with all
disclosures, warnings, cautions and instructions
concerning proper use of such accessories prior
to operating the vehicle and/or accessory. See a
GT-R certified NISSAN dealer for details concerning the particular accessories with which
your vehicle is equipped.
Your GT-R certified NISSAN dealer knows
your vehicle best. When you require any
service or have any questions, they will be
glad to assist you with the extensive
resources available to them.
READ FIRST — THEN DRIVE SAFELY
Before driving your vehicle, please read this
Owner’s Manual carefully. This will ensure
familiarity with controls and maintenance requirements, assisting you in the safe operation
of your vehicle.
alcohol or drugs.
.
ALWAYS observe posted speed limits and never drive too fast for
conditions.
.
ALWAYS give your full attention to
driving and avoid using vehicle
features or taking other actions that
could distract you.
.
ALWAYS use your seat belts and
appropriate child restraint systems.
Pre-teen children should be seated
in the rear seat.
.
ALWAYS provide information about
the proper use of vehicle safety
features to all occupants of the
vehicle.
.
ALWAYS review this Owner’s Manual for important safety information.
WARNING
IMPORTANT SAFETY INFORMATION
REMINDERS FOR SAFETY!
Follow these important driving rules to
help ensure a safe and comfortable trip
for you and your passengers!
.
NEVER drive under the influence of
MODIFICATION OF YOUR VEHICLE
This vehicle should not be modified. Modification could affect its performance,
safety or durability, and may even violate
governmental regulations. See the 2016
NISSAN GT-R Warranty Information Booklet for details including applicable exclusions.
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(4,1)
WHEN READING THE MANUAL
This manual includes information for all
features and equipment available on this
model. Features and equipment in your
vehicle may vary depending on model, trim
level, options selected, order, date of
production, region or availability. Therefore, you may find information about
features or equipment that are not included or installed on your vehicle.
All information, specifications and illustrations in
this manual are those in effect at the time of
printing. NISSAN reserves the right to change
specifications, performance, design or component suppliers without notice and without
obligation. From time to time, NISSAN may
update or revise this manual to provide owners
with the most accurate information currently
available. Please carefully read and retain with
this manual all revision updates sent to you by
NISSAN to ensure you have access to accurate
and up-to-date information regarding your vehicle. Current versions of vehicle Owner’s
Manuals and any updates can also be found in
the Owner section of the NISSAN website at
https://owners.nissanusa.com/nowners/navigation/manualsGuide. If you have questions concerning any information in your Owner’s Manual,
contact NISSAN Consumer Affairs. See the
NISSAN CUSTOMER CARE PROGRAM page
in this Owner’s Manual for contact information.
IMPORTANT INFORMATION ABOUT
THIS MANUAL
You will see various symbols in this manual. They
are used in the following ways:
NOTICE
This is used to indicate a hazard that
could cause damage to property or your
vehicle. To avoid or reduce the risk,
follow the information and instructions.
WARNING
This is used to indicate a hazard that
could cause death or serious personal
injury. To avoid or reduce the risk,
follow the information and instructions
exactly.
CAUTION
This is used to indicate a hazard that
could cause minor or moderate personal injury. To avoid or reduce the risk,
follow the information and instructions
carefully.
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(5,1)
Arrows in an illustration that are similar to those
above call attention to an item in the illustration.
apply, See www.dtsc.ca.gov/
hazardouswaste/perchlorate.”
This indicates the title and reference page.
All rights reserved. No part of this Owner’s
Manual may be reproduced or stored in a
retrieval system, or transmitted in any form, or
by any means, electronic, mechanical, photocopying, recording or otherwise, without the
prior written permission of NISSAN Motor Co.,
Ltd.
C 2014 NISSAN MOTOR CO., LTD.
*
CALIFORNIA PROPOSITION 65
WARNING
WARNING
If you see the symbol above, it means “Do not
do this” or “Do not let this happen”.
If you see a symbol similar to those above in an
illustration, it means the arrow points to the front
of the vehicle.
Arrows in an illustration that are similar to those
above indicate movement or action.
Engine Exhaust, some of its constituents, and certain vehicle components
contain or emit chemicals known to the
State of California to cause cancer and
birth defects or other reproductive
harm. In addition, certain fluids contained in vehicles and certain products
of component wear contain or emit
chemicals known to the State of California to cause cancer and birth defects
or other reproductive harm.
CALIFORNIA PERCHLORATE ADVISORY
Some vehicle parts, such as lithium batteries, may contain perchlorate material.
The following advisory is provided: “Perchlorate Material - special handling may
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(6,1)
NISSAN CUSTOMER CARE PROGRAM
NISSAN CARES ...
Both NISSAN and your GT-R certified NISSAN dealer are dedicated to serving all your automotive needs. Your satisfaction with your vehicle and your
GT-R certified NISSAN dealer are our primary concerns. Your GT-R certified NISSAN dealer is always available to assist you with all your automobile sales
and service needs.
However, if there is something that your GT-R
certified NISSAN dealer cannot assist you with
or you would like to provide NISSAN directly
with comments or questions, please contact the
NISSAN Consumer Affairs Department using
our toll-free number:
For U.S. customers
1-866-668-1GTR
(1-866-668-1487)
For Canadian customers
1-800-387-0122
The Consumer Affairs Department will ask for
the following information:
.
Your name, address, and telephone number
.
Vehicle identification number (attached to
the top of the instrument panel on the
driver’s side)
.
Date of purchase
.
Current odometer reading
.
Your NISSAN dealer’s name
. Your comments or questions
OR
You can write to NISSAN with the information on
the left at:
For U.S. customers
NISSAN North America, Inc.
Consumer Affairs Department
P.O. Box 685003
Franklin, TN 37068-5003
or via e-mail at:
nnaconsumeraffairs@nissan-usa.
com
For Canadian customers
NISSAN Canada Inc.
5290 Orbitor Drive
Mississauga, Ontario L4W 4Z5
or via e-mail at:
information.centre@nissancanada.
com
If you prefer, visit us at:
www.nissanusa.com (for U.S. customers) or
www.nissan.ca (for Canadian customers)
We appreciate your interest in NISSAN and
thank you for buying a quality NISSAN vehicle.
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(1,1)
Table of
Contents
GTR
GT-R Overview
Illustrated table of contents
0
Safety — Seats, seat belts and supplemental restraint system
1
Instruments and controls
2
Pre-driving checks and adjustments
3
Display screen, heater, air conditioner and audio systems
4
Starting and driving
5
In case of emergency
6
Appearance and care
7
Maintenance and do-it-yourself
8
Technical and consumer information
9
10
Index
Condition:
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(2,1)
(9,1)
GT-R Overview
GT-R specific information ............................................... GTR-3
Warranty information .................................................. GTR-3
Maintenance information ........................................... GTR-3
GT-R special specification parts ................................... GTR-3
Engine oil ....................................................................... GTR-3
Transmission oil ........................................................... GTR-4
Differential oil (front and rear) .................................. GTR-4
Brake fluid ..................................................................... GTR-4
GT-R special precautions ............................................... GTR-5
Tires and road wheels ............................................... GTR-5
Brake pad and disc rotor .......................................... GTR-5
Exhaust muffler and trunk carpet ............................ GTR-6
Titanium muffler and trunk carpet (if
so equipped) ................................................................ GTR-6
Dry carbon fiber parts (if so equipped) ................ GTR-7
Matte paint (if so equipped) .................................... GTR-8
GT-R performance optimization services .................... GTR-8
Wheel alignment inspection and adjustment
(if necessary) (including tire
pressure adjustment) ................................................. GTR-8
Transmission settings ................................................. GTR-9
Break-in schedule ............................................................. GTR-9
Wheel alignment ....................................................... GTR-10
Precautions before driving ...........................................
Vehicle Dynamic Control (VDC) OFF mode ....
Summer tires ............................................................
All-season tires ........................................................
Avoiding body damage ..........................................
Fuel .............................................................................
Body repair ...............................................................
Driving after replacing tires ..................................
Additional maintenance items .....................................
Precautions on performance driving ..................
Inspection and adjustments before driving ......
Inspection and adjustments after driving ..........
GT-R specific vehicle characteristics ........................
Refueling precautions ............................................
Gasoline smell .........................................................
Outside temperature display indicates
higher temperature .................................................
Idle speed is not steady ........................................
Engine speed is restricted ....................................
Engine output ...........................................................
Uneven wear of tires ..............................................
Noises are heard while driving ............................
Brake system information ......................................
[ Edit: 2014/ 12/ 8
GTR-10
GTR-10
GTR-11
GTR-11
GTR-11
GTR-12
GTR-12
GTR-12
GTR-12
GTR-13
GTR-14
GTR-18
GTR-23
GTR-23
GTR-23
GTR-23
GTR-23
GTR-23
GTR-23
GTR-24
GTR-24
GTR-26
Model: R35-D ]
(10,1)
Change of surface color of titanium muffler (if
so equipped) .............................................................. GTR-26
Sound heard around titanium muffler (if
so equipped) .............................................................. GTR-27
Dry carbon fiber parts (if so equipped) ............ GTR-27
Dual clutch transmission .............................................. GTR-27
Transmission operation characteristics ............. GTR-28
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(11,1)
GT-R SPECIAL SPECIFICATION
PARTS
GT-R SPECIFIC INFORMATION
The GT-R is NISSAN’s first supercar category
vehicle. The GT-R is equipped with special
systems. These systems are different than those
used on conventional vehicles to allow for the
high performance driving characteristics of this
vehicle. Your vehicle should be maintained by a
GT-R certified NISSAN dealer. Special skills,
knowledge and equipment are necessary to
properly maintain your GT-R.
WARRANTY INFORMATION
Please read this Owner’s Manual carefully,
together with your Warranty Information Booklet
which describes a number of express limitations,
exclusions and ways to void your warranty for
failing to follow the instructions contained in this
Owner’s Manual, including, but not limited to:
.
Failure to use proper parts, fuel and fluids,
.
Driving with the VDC off,
.
Racing,
.
Any competitive driving of any sort whatsoever,
.
Use on a track or driving on any airstrip,
.
Modifications, including adding/replacing,
reprogramming, attempting to reprogram,
altering, disconnecting any computer, control unit or electronic modules,
.
Deleting any or all stored information in any
computer, control unit or electronic module
including VSDR,
.
NOTICE
Only use the following specified fluids
and parts in the GT-R to avoid possible
vehicle damage.
Failure to have required GT-R Performance
Optimization Services performed.
In addition, see your tire warranty for specific
limitations or exclusions for operating summer
tires below −48F (−208C).
ENGINE OIL
MAINTENANCE INFORMATION
Mobil 1 (0W-40) (100% synthetic oil)
.
Special skills, knowledge and equipment are
necessary to properly inspect and adjust the
GT-R engine, transmission, suspension and
brakes to maintain performance. A GT-R
certified NISSAN dealer has the GT-R
certified technical staff and the special
equipment to properly maintain your GT-R.
.
NISSAN recommends maintenance items
that require the replacement of parts, engine
oil, oil filters and air filters should be
performed by a GT-R certified NISSAN
dealer. Make sure the specified fluids and
parts are used when the maintenance is
performed. NISSAN also recommends the
replacement of parts such as brakes should
be performed by a GT-R certified NISSAN
dealer.
Mobil 1 (0W-40) (100% synthetic) is the factory
fill oil. The VR38 engine with its plasma-sprayed
bores was developed using this oil. NISSAN
cannot ensure proper engine operation and
durability if other synthetic oil is used. If Mobil
1 (0W-40) is not available, Mobil 1 (10W-40)
(100% synthetic) may be used; however, some
performance loss may be noticed.
Furthermore, replacement of the engine oil with
MOTUL NISMO COMPETITION OIL type
2193E(5W40) is recommended for the frequent
high performance driving opportunities.
NISSAN cannot ensure proper engine operation
and durability if other synthetic oil is used.
The use of additives, chemical materials or
abrasive compounds is prohibited.
The use of additives, chemical materials, abrasive compounds or other high performance
GT-R Overview GTR-3
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(12,1)
engine oils may cause internal engine damage.
Engine oil maintenance
.
.
.
.
When the vehicle is delivered, the engine oil
level is 0.39 in (10 mm) below the H mark on
the engine oil dipstick for optimum high
performance driving. The engine oil can be
filled up to the H mark if not engaging in
performance driving.
Because of the high performance characteristics of the GT-R engine, more frequent oil
level inspections are necessary. Check the
oil level every 1,800 miles (3,000 km) and
adjust as necessary. Also, change the
engine oil based on the driving conditions.
For the information regarding oil replacement intervals, refer to the 2016 NISSAN
GT-R Service and Maintenance Guide.
mance driving. (
“Additional maintenance items” page GTR-12)
Make sure to replace the oil filter when the
engine oil is changed.
differential oil may cause the oil temperature to
increase and the final drive to be damaged. Also
it may cause vibration and adversely the vehicle
handling characteristics.
TRANSMISSION OIL
BRAKE FLUID
Genuine NISSAN Transmission Oil R35
Special (100% synthetic oil)
Genuine NISSAN Brake Fluid R35 Special
II
The GT-R uses a multiple-disc dual wet clutch
transmission. The specially developed transmission oil maximizes the friction characteristics of
the clutch and the lubrication of the gear
bearings.
Genuine NISSAN Brake Fluid R35 Special II is
the factory fill brake fluid. The Vehicle Dynamic
Control (VDC) unit and other related parts were
specially designed for this brake fluid. NISSAN
cannot ensure proper operation of the vehicle if
other brake fluid is used.
The use of additives is prohibited.
The use of additives or other transmission oil
may cause internal transmission or clutch
damage.
Some amount of oil is consumed by your
engine under normal operating conditions,
and oil consumption by itself does not
necessarily indicate any malfunction. If your
rate of oil consumption increases suddenly
or without explanation, NISSAN recommends that you have your vehicle inspected
by a GT-R certified NISSAN dealer.
DIFFERENTIAL OIL (front and rear)
For information about the oil replacement
intervals for performance driving, refer to the
interval for replacing oil after high perfor-
The use of additives is prohibited.
GTR-4
Differential Oil R35 COMPETITION type
2189E
Use only the Differential Oil R35 COMPETITION
type 2189E that can keep the oil temperature
low in order to protect all parts of the differential
and maximize the performance of the Limited
Slip Differential (LSD).
Using additives or any other than the specified
GT-R Overview
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(13,1)
GT-R SPECIAL PRECAUTIONS
Contact your GT-R certified NISSAN dealer.
They can recommend if an individual tire or a
complete set should be replaced.
TIRES AND ROAD WHEELS
Tires
The GT-R uses specially designed run-flat tires
and matching road wheels. Use of these
specially developed tires and wheels provides
the greatest potential for maximum performance.
.
.
.
Using non-genuine GT-R tires may cause
powertrain system damage if the vehicle is
driven in a flat tire situation, even if run-flat
tires are used. This may also prevent the
vehicle from being stopped safely.
.
.
Using non-genuine GT-R tires may also
cause tire failure due to excessive heat
buildup caused by tire distortion while
driving.
Using non-genuine GT-R tires may affect the
operation of the VDC system.
Tire replacement:
.
When tire replacement is required, replacing
tires as a set of four with new tires is
recommended. However, if a tire is punctured or damaged, it may be possible to
replace only the damaged tire. Determining
whether one tire or a complete set of tires
should be replaced is based on a number of
factors including tire wear and condition.
.
The GT-R uses specially designed run-flat
tires which have a rigid side wall. Special
equipment and procedures are required
when replacing these tires. NISSAN recommends that tire replacement be performed at
a GT-R certified NISSAN dealer.
Specific tire changing equipment must be
used to remove the GT-R tires from the
wheel and to install the GT-R tires onto the
wheel. It is only possible to reuse the tires
when they have no cracks and/or deformations on the bead portion of the tire. If the
incorrect equipment is used to remove the
GT-R tires from the wheel and to install the
GT-R tires onto the wheel, cracks and
deformation may occur on the bead portion
of the tires meaning that the tires cannot be
reused. Contact a GT-R certified NISSAN
dealer if the tires need to be removed from
the wheels.
When reusing tires, contact a GT-R certified
NISSAN dealer.
Road wheels
Using non-genuine GT-R wheels may cause the
following:
.
vehicle vibration
.
the tire coming loose from the wheel during
a flat tire
.
reduced wheel lug nut tightness
BRAKE PAD AND DISC ROTOR
This vehicle is equipped with cross-drilled
floating rotors and radial-mounted six-piston
monoblock calipers. This helps to achieve
excellent stopping performance and fade-resistance.
Using non-genuine GT-R brake pads or rotors
can affect vehicle braking performance and the
operation of the ABS and VDC system.
Replacement of brake pads and disc
rotors
NISSAN generally recommends to replace all
four sets of brake pads and disc rotors at the
same time to maintain maximum brake performance.
However, replacing only the brake pads may be
allowed in some cases (four wheels or only front
wheels depending on the conditions). A GT-R
GT-R Overview GTR-5
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(14,1)
certified technician must inspect the vehicle and
determine that only the brake pads need to be
replaced. In this case, replacing all brake pads
and disc rotors as a set is not necessary.
Note that the replacement of brake pads and the
disc rotors as a set on all four wheels should be
performed when a GT-R certified technician
determines that this is the correct repair.
If the inside of the disc rotors are cold during the
winter and the surface becomes hot due to a
heavy force being applied repeatedly to the
brakes, cracks may occur near the coolant hole
on the surface of the disc rotor. Cracks may also
occur due to a heavy force being repeatedly
applied to the brakes during high performance
driving. In these cases it may be necessary to
replace the disc rotors or brake pads depending
on the condition of the crack. Contact a GT-R
certified NISSAN dealer for replacement.
EXHAUST MUFFLER AND TRUNK
CARPET
The GT-R exhaust system is designed to provide
the maximum vehicle performance and to
protect the vehicle from high exhaust gas
temperatures.
If non-genuine GT-R exhaust system parts are
used it is possible that the muffler or other
exhaust system parts will deform and cause
GTR-6
damage to the underbody. Non-genuine GT-R
exhaust system parts can also affect vehicle
performance and possibly lead to turbocharger,
engine or power train related parts including
transmission, damage.
Also, do not remove the trunk carpet from the
vehicle for any reason. The carpet insulates the
vehicle interior from the heat of the muffler and
from the noise of the transmission.
TITANIUM MUFFLER AND TRUNK
CARPET (if so equipped)
The vehicle is equipped with a label under the
1 that provides the body to the
console lid *
titanium muffler clearance specification (for
example rear bumper to muffler tube clearance).
Since the exhaust gas temperature of the high
performance engine reaches a high temperature
(1,8328F (1,0008C) or more), the muffler may be
deformed or lowered due to the heat and then
the underbody or peripheral parts may be
damaged. Therefore, periodic inspections for
the clearance between the muffler and the
peripheral parts are required. Your GT-R has
GT-R Overview
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(15,1)
been tested on a test circuit to ensure the
suspension components “settle” prior to shipping. Following this circuit test the odometer
reading at the time of vehicle shipment is as
listed. Please note a small amount of additional
mileage may have been added in the subsequent onward transportation. In addition your
GT-R has been inspected and tested by the
factory test personnel. The titanium muffler
specifications are provided on a label under
the console lid should the muffler need to be
adjusted. Please do not remove the label from
the console lid. See a GT-R certified NISSAN
dealer for detailed information.
If a non-genuine titanium muffler is used, the
muffler may become deformed and damage the
underbody due to the high performance engine
reaching high exhaust gas temperatures
(1,8328F (1,0008C) or more). The highest-class
titanium alloy is used for genuine parts to ensure
the resistance strength and creeping characteristics against high exhaust gas temperature. In
addition, further cooling effects are secured by
adopting additional cooling fins and by applying
partial plate thickness reduction. Since genuine
titanium mufflers are made of titanium alloy, the
surface color will change depending on the
driving conditions, which is not unusual. Prior to
shipping from factory, all vehicles receive
balance aligning for engine, transmission, and
clutch, as well as quench driving of brake pads
and rotors. As a result, the muffler surface color
may differ depending on the vehicle.
Never remove the trunk carpet from the vehicle
for any reason. The carpet insulates the vehicle
interior from the heat of the muffler and from the
noise of the transmission.
Never Allow Oil or Grease to Adhere to the
Titanium Muffler.
If the muffler is heated when oil or grease adhere
to the muffler surface, the color of this area will
be different from that of the surrounding area. To
remove the oil or grease, check that the surface
temperature of the muffler has cooled, wash the
area with a neutral detergent, wipe it with a
brake cleaner-sprayed clean shop cloth and
gently tap it with a dry shop cloth to dry. Be
careful not to allow the brake cleaner to splatter
on rubber parts, bumper, etc.
DRY CARBON FIBER PARTS (if so
equipped)
Because of the characteristics of the material,
the dry carbon fiber parts may turn yellow due to
exposure to ultraviolet rays. The surfaces of dry
carbon fiber parts are coated with a special
ultraviolet protection paint. To maintain the
appearance of these parts, it is important to
take proper care of them.
NOTICE
.
Do not use compound agents on
clear-coated dry carbon fiber parts
(such as the NISMO model’s bumper, side sill protector, rear spoiler,
etc.).
.
Do not use any chemical agents
(wax, coating agent, compound
agent, etc.) on matte-painted dry
carbon fiber parts (such as the rear
diffuser, a rear spoiler that is of
specifications other than NISMO,
etc.).
.
When dry carbon fiber parts become
dirty, prepare a dilute cleaning solution by mixing one capful of mild
detergent in a bucket of water, and
GT-R Overview GTR-7
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(16,1)
GT-R PERFORMANCE
OPTIMIZATION SERVICES
use that mixture to clean the parts.
NOTE:
The surfaces of the dry carbon fiber parts
are lightly coated like a race car so that
you can feel the proper texture of real
carbon, which may feel rough. This is
normal.
MATTE PAINT (if so equipped)
If your vehicle is equipped with matte paint,
special care is necessary to clean your vehicle to
maintain the appearance of the matte paint.
(
“Matte paint care” page 7-2)
In addition to the regular maintenance recommended by NISSAN, the GT-R requires the
following special inspections:
.
.
1,000 miles
.
12 months
.
24 months
.
36 months
NOTE:
. These inspections will be performed
free of charge for labor at a GT-R
certified NISSAN dealer only. Inspections thereafter are recommended
every 12 months or 12,000 miles
(whichever comes first) at the customer’s expense. See the 2016 NISSAN
GT-R Warranty Information Booklet for
details.
GTR-8
.
See the 2016 NISSAN GT-R Warranty
Information Booklet for significant limitations, exclusions and possible voiding of your warranty resulting from
failure to have these necessary inspections, repairs and/or adjustments performed.
.
See the 2016 NISSAN GT-R Service and
Maintenance Guide for a detailed explanation of the GT-R Performance
Optimization Services.
Wheel alignment inspection and adjustment
(if necessary) (including tire pressure adjustment)
. Transmission settings
These inspections are required at the following
intervals:
.
inspections are performed at the customer’s expense.
Repairs and adjustments involving
parts replacement, etc. determined to
be necessary as a result of these
WHEEL ALIGNMENT INSPECTION
AND ADJUSTMENT (if necessary)
(including tire pressure adjustment)
This vehicle is equipped with a high performance suspension. The vehicle’s wheel alignment needs to be measured and adjusted (if
necessary) by a GT-R certified NISSAN dealer
as necessary as the vehicle is driven and the
suspension parts break-in.
The wheel alignment can be adjusted by a GT-R
certified NISSAN dealer in accordance with
specifications for city driving to high performance driving.
The tires on the GT-R may have different wear
GT-R Overview
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(17,1)
BREAK-IN SCHEDULE
rates and wear patterns in comparison to
conventional passenger vehicles. Contact a
GT-R certified NISSAN dealer to confirm that
the alignment is within specifications.
Preventing toe-out:
Toe-out can cause uneven tire wear or
damage to areas inside the tires due to
high heat. Be sure to have the wheel
alignment toe-in setting checked and adjusted by your GT-R certified NISSAN
dealer before any performance driving on
closed circuit tracks. Obey all traffic laws
when on public roads.
Toe-in specification
Front
Rear
0.059 in (1.5 mm)
0.079 in (2.0 mm)
TRANSMISSION SETTINGS
The design of the clutch and transmission
requires inspection and adjustment of the clutch
and shift forks by a GT-R certified NISSAN
dealer at the recommended intervals. If the
transmission setting is not complete, excessive
loads may be applied to the transmission and
power train system parts during starting and
shifting, which may result in a malfunction or
damage. Depending on the driving conditions,
more frequent adjustments may be necessary to
help maximize vehicle performance.
NOTICE
Follow these recommendations to obtain maximum engine performance and
ensure the future reliability and economy of your new vehicle. Failure to
follow these recommendations may
result in shortened engine life and
reduced vehicle performance.
Please observe the following types of driving
until the mileage shown below has been
reached.
Until 300 miles (500 km):
.
Do not depress the accelerator pedal more
than halfway and avoid rapid acceleration.
.
Drive with the engine speed kept at less
than 3,500 RPM.
.
Avoid unnecessary quick steering, abrupt
braking and driving on poor roads.
300 to 600 miles (500 to 1,000 km):
.
Avoid rapid acceleration in a low gear (1st to
3rd gears) with the accelerator pedal fully
depressed. Depress the pedal slowly.
.
Avoid unnecessary quick steering and
abrupt braking.
GT-R Overview GTR-9
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(18,1)
PRECAUTIONS BEFORE DRIVING
.
Drive with the suspension setup switch in
the COMF mode to allow more suspension
stroke.
600 to 1,200 miles (1,000 to 2,000 km):
WHEEL ALIGNMENT
.
Do not adjust the wheel alignment until the
mileage reaches 1,000 miles (1,600 km). Until
then, the suspension may not engage enough
and the height may be higher.
.
Drive with the engine speed kept relatively
M position.
high with the shift lever in the &
Shifting is recommended between 1st and
4th gears.
Avoid unnecessary quick steering and
abrupt braking.
.
Drive with the suspension setup switch in
the COMF mode to allow more suspension
stroke.
Even though the mileage reaches over 1,200
miles (2,000 km), the clutch may take longer to
properly engage if the vehicle is mainly driven in
town at a low speed. NISSAN recommends
breaking in the clutch at a GT-R certified
NISSAN dealer. Always perform the transmission setting after breaking in the clutch. If the
transmission setting is not complete, excessive
loads may be applied to the transmission and
power train system parts during starting and
shifting, which may result in a malfunction or
damage.
GTR-10
However, make sure to adjust the alignment
after 1,000 miles (1,600 km).
The wheel alignment can be adjusted by a GT-R
certified NISSAN dealer in accordance with
specifications for city driving to high performance driving.
The tires on the GT-R may have different wear
rates and wear patterns in comparison to
conventional passenger vehicles. Contact a
GT-R certified NISSAN dealer to confirm that
the alignment is within specifications.
VEHICLE DYNAMIC CONTROL (VDC)
OFF MODE
Always make sure the VDC is ON before driving
the vehicle by checking that the VDC OFF
indicator lights on the meter and the VDC set-up
switch are not illuminated. The GT-R is a high
performance vehicle and the VDC must be on/
activated to provide proper powertrain operation
and intended drivability.
WARNING
.
The VDC OFF mode should ONLY be
used briefly to help free the vehicle
if stuck in snow or mud by temporarily stopping operation of the VDC
to maintain wheel torque.
.
Driving the GT-R with the VDC off
may lead to handling issues related
to steering maneuvers, acceleration,
or deceleration. Moreover, driving
with the VDC off can result in an
inoperative vehicle by causing serious damage to the powertrain,
including damage to the Transaxle
Assembly including Transfer, Clutch,
Gears, Transaxle case and all of its
components and other drivetrain
GT-R Overview
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(19,1)
component(s) by overheating or excessive force.
.
Damage to the powertrain or any
drivetrain component(s) that occurs
when there is a record in the Vehicle
Status Data Recorder (VSDR) that
the vehicle was driven with VDC off
during the period when the damage
was incurred is excluded from warranty coverage.
See your 2016 Warranty Information Booklet for
important related information and warranty
coverage exclusions. See also section 2
(
“Transmission warning light” page 2-30)
and section 5 (
“Vehicle Dynamic Control
(VDC) system” page 5-50) of this Owner’s
Manual, “Transmission Clutch Temperature
High” and “Vehicle Dynamic Control (VDC)
System” for important additional related information.
SUMMER TIRES
The GT-R summer tires are made from a
specially formulated rubber to maximize the
vehicle’s performance capabilities. Performance
of summer tires is substantially reduced when
temperatures are less than 328F (08C) so you
must drive carefully. NISSAN recommends the
use of winter or all-season tires on all four
wheels if you plan to operate your vehicle in
snowy or icy conditions when temperatures are
less than 328F (08C).
WARNING
Never use summer tires when the
temperature is below −48F (−208C) to
prevent permanent tread deformation
which may cause tire damage or tire
failure. This may cause a loss of vehicle
control which can result in serious
personal injury or death.
ALL-SEASON TIRES
Do not exceed the speed rating of the tire that is
installed on the vehicle.
AVOIDING BODY DAMAGE
The GT-R bumper, fascia, side sills and undercarriage are close to the ground. Drive slowly on
rough or uneven roads to avoid damaging these
parts. Pay careful attention to wheel blocks and
curbs. If the front bumper contacts a wheel
block, curb, etc., the bumper and underlying
parts may be damaged or cracked. Be careful
not to damage the front spoiler that is installed
below the engine room.
GT-R Overview GTR-11
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(20,1)
ADDITIONAL MAINTENANCE ITEMS
FUEL
NISSAN recommends using fuels that contain
no alcohol. However, fuels containing up to 10%
alcohol may be used, if necessary. Do not use E15 or E-85 in your vehicle. (
“Fuel information” page 9-4)
NOTICE
To avoid serious engine damage due to
increased cylinder temperatures, do not
use fuels that contain more alcohol
than indicated in
“Gasoline containing oxygenates” page 9-4. Also, do
not use fuel additives, fuel stabilizers or
fuel deicers that contain alcohol.
BODY REPAIR
The body of the GT-R has been manufactured
on special fixtures utilizing a hybrid structure
with aluminum die cast parts for the frame work.
Special skills, information and equipment are
required to correctly repair the body. Contact a
GT-R certified NISSAN dealer if the vehicle is
damaged, such as in a collision, and they will
recommend an appropriate body shop.
proved by NISSAN for repairing structural body
damage. Contact a GT-R certified NISSAN
dealer or NISSAN Consumer Affairs for a
referral or list of certified body shops.
DRIVING AFTER REPLACING TIRES
Avoid the driving conditions listed under “Additional maintenance items” in this section for 48
hours after tires are installed on the wheels
(
“Additional maintenance items” page
GTR-12). The tire may slip on the wheel if the
vehicle is driven in these conditions before 48
hours have passed. If the tire slips on the wheel,
the wheel/tire assembly will be out of balance
and will require rebalancing.
The information and specifications in this
section apply only when engaging in
performance driving.
The following information applies only if you
engage in performance driving such as driving
your GT-R for extended periods under the
following conditions.
.
Higher-RPM (approaching redline) operation
.
Frequent high pedal force braking from
moderate and higher speeds
.
Frequent throttle activation
. Fast revving throughout the RPM range
In such cases, the following additional maintenance guidelines apply.
However, you should also carefully read
your 2016 NISSAN GT-R Warranty Information Booklet for important information
concerning warranty coverage, limitations
and exclusions.
We recommend that all GT-R maintenance be
performed at a GT-R certified NISSAN dealer.
NISSAN will only pay for GT-R Performance
Optimization Services performed at a GT-R
certified NISSAN dealer.
Only certified body shops using CELETTE®
advanced collision repair equipment are ap-
GTR-12
GT-R Overview
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(21,1)
PRECAUTIONS ON PERFORMANCE
DRIVING
condition and engine output is reduced.
.
The information and specifications in this
section apply only when engaging in
performance driving.
Checking the temperature of the
coolant and oils on the multi function display
When the temperatures of the engine coolant
and oil, and the oil pressure exceed the normal
range, the color of the meter on the multi
function display changes to red to warn the
driver. When engaging in high performance
driving, switch the display to the function meter
to display the temperature of the engine coolant
and oil, and the oil pressure. When the color of
the meter display changes to red, perform cool
down driving. When the values of the temperature and pressure return to the normal range, the
color of the meter display will turn back to white.
Warning temperature:
.
Engine coolant temperature is 2308F
(1108C) or higher:
If the engine coolant temperature increases
above 2308F (1108C), the color of the meter
display on the multi function display changes
to red to warn of a possible overheat
.
Engine oil temperature is 2758F (1358C) or
higher:
If the engine oil temperature is higher than
2758F (1358C), the meter display changes
to red, maximum engine speed is automatically limited to 4,000 rpm, and the transmisM
sion automatically changes from the &
A position.
position to the &
Transmission oil temperature is 2848F
(1408C) or higher:
If the transmission oil temperature increases
to over 2848F (1408C), the color of the
meter display changes to red. However, the
vehicle can continue to be driven until the
temperature reaches 2958F (1468C). If the
oil temperature exceeds 2848F (1408C)
while driving (the color of the meter displayed in red), change both the transmission
oil and the differential oil after driving
because these fluids have deteriorated
because of the heat.
Cool down
The information and specifications in this
section apply only when engaging in
performance driving.
Cool down the vehicle to help extend the life of
the vehicle if coolant temperatures are extremely
high. Drive the vehicle at 37 to 50 MPH (60 to
80 km/h), in 5th or 6th gear for 2 to 3 miles (3 to
5 km) and then stop the engine.
Refueling precautions
WARNING
Do not attempt to top off the fuel tank
after the fuel pump nozzle shuts off
automatically. Continued refueling may
cause fuel overflow, resulting in fuel
spray and possibly a fire. The fuel tank
is full at the first automatic shutoff.
To maximize vehicle performance, the fuel tank is
located as low as possible to lower the vehicle
center of gravity. The tank is also divided into
two parts. This fuel tank design causes higher
pressures inside the tank than other vehicles so
fuel spillage is possible by trying to top off the
fuel tank after automatic shutoff.
The fuel tank pressure is higher when the vehicle
is hot, especially if the tank is more than half full.
If the cap is opened when the vehicle is hot, it
may cause fuel spray and there may be a hissing
noise. Open the cap slowly, releasing the
pressure from the tank gradually. Also, if the
GT-R Overview GTR-13
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(22,1)
necessarily indicate any malfunction. If your
rate of oil consumption increases suddenly
or without explanation, NISSAN recommends that you have your vehicle inspected
by a GT-R certified NISSAN dealer.
vehicle is refueled when the vehicle is hot, the
fuel pump may automatically shut off before the
tank is full. This does not indicate that there is a
malfunction. Refuel slowly or refuel after the
vehicle has cooled.
INSPECTION AND ADJUSTMENTS
BEFORE DRIVING
The information and specifications in this
section apply only when engaging in
performance driving.
Fluids
.
Check the engine, transmission, differential
and under vehicle surfaces for oil and
coolant leaks.
.
Check the fluid levels and adjust as necessary using the specified fluid as described
under the conditions listed in this section.
(
“Recommended fluids and maintenance interval” page GTR-19 ) If you do
not drive under the conditions listed, refer to
the 2016 NISSAN Service and Maintenance
Guide.
GTR-14
.
NISSAN recommends to adjust the engine
1 to be 0.39 in (10 mm) (1/8 gal
oil level *
2 below the H mark on the
(0.5 liters)) *
3 range is 1.18 in (30
engine oil dipstick. (*
mm).) Before checking the oil level, run the
engine until it reaches operating temperature and wait at least 5 minutes after turning
off the engine. Make sure the oil level always
remains above the L mark.
When the vehicle is delivered, the engine oil
is set to “H- 0.39 in (10 mm)” for optimal
high performance driving.
.
Some amount of oil is consumed by your
engine under normal operating conditions,
and oil consumption by itself does not
GT-R Overview
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(23,1)
Check the coolant level in the pressurized
coolant reservoir. Adjust the level so that the
fluid is between the MAX and MIN markings. For
the coolant, use genuine NISSAN Long Life
coolant. (On delivery of new vehicle, the
reservoir is filled to the MIN level. Be sure to
replenish approximately 3/8 US quart (0.3 to 0.4
liter) of coolant.)
Engine and powertrain
The information and specifications in this
section apply only when engaging in
performance driving.
.
Check the engine, transmission, differential
and under the vehicle for oil and coolant
leaks.
.
Inspect the areas surrounding of the catalytic converter for heat deterioration.
.
Always perform the transmission setting.
After that, adjust the clutch clearance so
that the clearance is less than the clearance
used for daily driving. Your GT-R certified
NISSAN dealer has the necessary information and equipment to set the clutch
clearance to the correct specification. The
clearance used for daily driving increases
clutch heat generated during Performance
Driving. This leads to an increase in temperature of the transmission oil. In addition, a
more direct shifting feel can be obtained by
reducing the clutch clearance for Performance Driving. The clutch clearance should
be reset to the daily driving specification
after Performance Driving. See your GT-R
certified NISSAN dealer for information.
NOTICE
Do not overfill the coolant. This may
increase the pressure in the cooling
system and cause coolant leaks.
.
Adjust the power steering fluid level to the R
5
mark *
on the power steering dipstick
6
when the fluid temperature is hot or *
when the fluid temperature is cold.
Fluid temperature:
Hot: 122 to 1768F (50 to 808C): between
1 and *
5
*
3
Cold: 32 to 868F (0 to 308C): between *
6
and *
Coolant level and mixture ratio
The information and specifications in this
section apply only when engaging in
performance driving.
To maximize vehicle performance, the coolant
mixture ratio should be a combination of 30%
coolant antifreeze and 70% demineralized or
distilled water for maximum cooling system
performance regardless of ambient temperatures.
If ambient temperatures are anticipated below
58F (−158C), make sure a proper mixture ratio of
50% antifreeze and 50% demineralized or
distilled water mix is used.
GT-R Overview GTR-15
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(24,1)
NOTICE
Failure to have the clutch properly
adjusted before performance driving
may cause the transmission oil temperature to increase which may cause
transmission damage.
.
.
Inspect and confirm the clearance between
the exhaust finisher and rear bumper is more
than 0.24 in (6 mm) (up/down) and more
than 0.20 in (5 mm) (left/right).
Inspect the dust boot of the drive shaft
universal joint for cracks or damage.
Suspension and wheel alignment
The information and specifications in this
section apply only when engaging in
performance driving.
.
Check the steering and suspension system
and other links for loose and/or damaged
parts.
.
Measure and adjust the wheel alignment.
(
“Wheel alignment” page GTR-10)
Contact a GT-R certified NISSAN dealer to
adjust the wheel alignment to the recommended setting for high performance driving.
GTR-16
Preventing toe-out:
Wheels and tires
Toe-out can cause uneven tire wear or
damage to areas inside the tires due to
high heat. Be sure to have the wheel
alignment toe-in setting checked and adjusted by your GT-R certified NISSAN
dealer before any performance driving on
closed circuit tracks. Obey all traffic laws
when on public roads.
The information and specifications in this
section apply only when engaging in
performance driving.
Toe-in specification
Front
Rear
0.059 in (1.5 mm)
0.079 in (2.0 mm)
.
Check tire wear and cracking.
.
Inspect the tire side wall for damage.
.
Check the tire pressure and adjust the
pressure as necessary when the tires are
cold. (
“Wheels and tires” page 8-32)
The tire pressure changes depending on the
outside temperature or altitude. Check the tire
pressure regularly and when the climate conditions change.
* The following chart indicates how the tire
pressure will decrease as outside air temperature decreases.
GT-R Overview
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(25,1)
cap by hand. If a tool is used to tighten the
cap, the cap may be damaged.
.
Make sure the wheel nuts are tight.
(
“Wheels and tires” page 8-32)
.
Make sure the drive shaft nuts are tight.
.
Make sure to replace the grommet seal, the
valve core and the valve cap of the Tire
Pressure Monitoring System (TPMS) sensor
attached to the wheel every 3 years for
performance driving use. Replace them
every 5 years even when not engaging in
performance driving. A dirty grommet seal
will cause the air leak from the tire.
.
Make sure that the nuts and valves that are
attached to the TPMS sensor are tight and
there is no nitrogen leak.
.
Use only a NISSAN genuine valve cap or
equivalent.
.
Check wheel hub run out and that the wheel
rotates smoothly without any friction. Check
these with the tires removed whenever an
inspection is performed with the vehicle
jacked up.
.
Secure road wheel balance weights with
aluminum tape.
.
Check that the wheel nuts are not stripped.
WARNING
Keep your tires inflated to the correct
tire pressure. Driving with low tire
pressure can damage some powertrain
systems and affect the operation of the
ABS and VDC systems. Low Tire pressure may also cause tire failure and
result in serious personal injury or
death.
.
Make sure the tire valve stem cap is installed
and that the valve stem is tight. When
installing the cap, make sure to tighten the
.
Make sure the tire has not slipped on the
wheel causing the assembly to be out of
balance. The reference marks on the tire and
wheel should be aligned. If the reference
marks are not aligned, the tire has slipped on
the wheel. Have the wheels/tires rebalanced. Make sure the old reference marks
are erased and new reference marks are
applied to the wheel and tire. When installing new tires on the wheels, make sure new
reference marks are applied to the wheels
and tires.
.
Avoid the driving conditions listed under
“Additional maintenance items” in this section for 48 hours after tires are installed on
GT-R Overview GTR-17
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(26,1)
the wheels. The tire may slip on the wheel if
the vehicle is driven in these conditions
before 48 hours have passed. If the tire slips
on the wheel, the wheel/tire assembly will be
out of balance and will require rebalancing.
The information and specifications in this
section apply only when engaging in
performance driving.
Brakes
NOTICE
The information and specifications in this
section apply only when engaging in
performance driving.
.
Check for the heat deterioration of the
brakes and parts around the brakes.
.
It is recommended that you remove air from
the brake system after any of the following:
— When engaging in high performance
driving for the first time after purchasing
a new vehicle.
— After replacing the brake fluid.
— When engaging in high performance
driving for a sustained period of time. It
is recommended that bleeding the brake
be performed when the brake calipers
are hot (about 2128F (1008C)).
Brake pad break-in procedure:
NISSAN recommends that a special brake pad
break-in procedure be performed before engaging in performance driving. Contact a GT-R
certified NISSAN dealer for details.
GTR-18
drive under the conditions listed, refer to the
2016 NISSAN Service and Maintenance
Guide.
INSPECTION AND ADJUSTMENTS
AFTER DRIVING
.
When changing fluids, be sure to use the
specified fluids as described in this Owner’s
manual. (
“Capacities and recommended fluids/lubricants” page 9-2)
At the completion of performance driving, all fluid and other adjustments
should be returned to the normal fluid
specifications as shown in the “Maintenance and do-it-yourself” section of
this manual.
Fluids
The information and specifications in this
section apply only when engaging in
performance driving.
.
Check the engine, transmission, differential
and under the vehicle for oil and coolant
leaks.
.
Check the fluid levels and adjust as necessary using the specified fluid as described
under the conditions listed in this section.
(
“Recommended fluids and maintenance interval” page GTR-19) If you do not
GT-R Overview
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(27,1)
Recommended fluids and maintenance interval
The information and specifications in this section apply only when engaging in performance driving.
ITEMS
GT-R SPECIFIED FLUIDS
Engine Oil
Mobil 1 (0W-40)*1
. When the oil temperature stays
below 2308F (1108C) while driving
.
MAINTENANCE INTERVAL
.
*1:
Change engine oil and engine oil filter at the same interval as Schedule 1 and
2 in the 2016 NISSAN GT-R Service and Maintenance Guide.
When the oil temperature reaches
between 2308F (1108C) and 2668F (1308C) while
driving
Change engine oil and engine oil filter every 3,000 miles (5,000 km).
When the oil temperature exceeds
2668F (1308C) while driving
Change engine oil and engine oil filter immediately after stopping.
Mobil 1 (0W-40) (100% synthetic) is the factory fill oil. The VR38 engine with its plasma-sprayed bores was developed using this oil. NISSAN cannot ensure proper
engine operation and durability if other 0W-40 synthetic oil is used. If Mobil 1 (0W-40) is not available, Mobil 1 (10W-40) (100% synthetic) may be used; however,
some performance loss may be noticed.
GT-R Overview GTR-19
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(28,1)
ITEMS
GT-R SPECIFIED FLUIDS
Transmission Oil
Genuine NISSAN Transmission Oil R35 Special
. When the oil temperature stays
below 2488F (1208C) while driving
.
MAINTENANCE INTERVAL
.
When the oil temperature reaches
between 2488F (1208C) and 2848F (1408C) while
driving
Change transmission oil every 3,000 miles (5,000 km).
When the oil temperature exceeds
2848F (1408C) while driving
Change both transmission oil and differential oil immediately after stopping.
Differential oil temperature usually increases concurrently.
ITEMS
GT-R SPECIFIED FLUIDS
Differential Oil (front and rear)
Differential Oil R35 COMPETITION type 2189E*2
. When the oil temperature stays
below 2488F (1208C) while driving
.
MAINTENANCE INTERVAL
.
*2:
Change transmission oil at the same interval as Schedule 1 and 2 in the 2016
NISSAN GT-R Service and Maintenance Guide.
Change differential oil at the same interval as Schedule 1 and 2 in the 2016
NISSAN GT-R Service and Maintenance Guide .
When the oil temperature reaches
between 2488F (1208C) and 2848F (1408C) while
driving
Change differential oil every 3,000 miles (5,000 km).
When the oil temperature exceeds
2848F (1408C) while driving
Change both transmission oil and differential oil immediately after stopping.
Differential oil temperature usually increases concurrently as the transmission
oil temperature.
The differential oil temperature cannot be displayed on the multi function display. The differential oil temperature can be checked with the transmission oil temperature
since both usually increases or decrease concurrently.
GTR-20
GT-R Overview
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(29,1)
ITEMS
Brake Fluid
GT-R SPECIFIED FLUIDS
Genuine NISSAN Brake Fluid R35 Special II*3
MAINTENANCE INTERVAL
Change brake fluid every 3,000 miles (5,000 km).
*3:
Genuine NISSAN Brake Fluid R35 Special II is the factory fill brake fluid. The Vehicle Dynamic Control (VDC) unit and other related parts were specially designed for
this brake fluid and NISSAN cannot ensure the best performance and proper operation of the vehicle if other brake fluid is used.
GT-R Overview GTR-21
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(30,1)
inspection is performed with the vehicle
jacked up.
Suspension and wheel alignment
.
.
Check the steering and suspension system
and other links for loose and/or damaged
parts.
.
Measure and adjust the wheel alignment.
Contact a GT-R certified NISSAN dealer to
adjust the wheel alignment to the recommended setting for normal driving.
Wheels and tires
Make sure the tire has not slipped on the
wheel causing the assembly to be out of
balance. The reference marks on the tire and
wheel should be aligned. If the reference
marks are not aligned, the tire has slipped on
the wheel. Have the wheels/tires rebalanced. Make sure the old reference marks
are erased and new reference marks are
applied to the wheel and tire. When installing new tires on the wheels, make sure new
reference marks are applied to the wheels
and tires. (
“Wheels and tires” page
GTR-16)
.
Check tire wear and cracking.
.
Inspect the tire side wall for damage.
.
Check the tire pressure and adjust the
pressure as necessary when the tires are
cold. (
“Wheels and tires” page GTR16) If you do not drive under the conditions
listed in this section, see
“Wheels and
tires” page 8-32.
.
Check that the wheel nuts are not stripped.
Check if there is no deformation on the
contact surface of the wheel nuts.
.
Check for the heat deterioration of the
brakes and parts around the brakes.
Check the condition of the brake pads and
disc rotors and replace them as necessary.
.
Make sure that the TPMS sensor installation
nuts and the sensor valve are tight and there
is no nitrogen leak.
Inspect the area surrounding the catalytic
converter for heat deterioration.
.
Inspect and confirm the clearance between
the exhaust finisher and rear bumper is more
than 0.24 in (6 mm) (up/down) and more
than 0.20 in (5 mm) (left/right).
.
The clutch clearance and shift fork position
may need to be adjusted.
.
Inspect the dust boot of the drive shaft
universal joint for cracks or damage.
.
Check that there is no abnormal noise,
vibrations or warning lights illuminated when
making tight turns at slow speed (for tight
corner braking phenomenon).
Brakes
.
Make sure the wheel nuts are tight.
(
“Wheels and tires” page 8-32)
.
.
Make sure the drive shaft nuts are tight.
Engine and powertrain
.
Check wheel hub run out and that the wheel
rotates smoothly without any friction. Check
these with the tires removed whenever an
.
GTR-22
leaks.
.
Check the engine, transmission, differential
and under the vehicle for oil and coolant
GT-R Overview
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(31,1)
GT-R SPECIFIC VEHICLE
CHARACTERISTICS
REFUELING PRECAUTIONS
WARNING
Do not attempt to top off the fuel tank
after the fuel pump nozzle shuts off
automatically. Continued refueling may
cause fuel overflow, resulting in fuel
spray and possibly a fire. The fuel tank
is full at the first automatic shutoff.
To maximize vehicle performance, the fuel tank is
located as low as possible to lower the vehicle
center of gravity. The tank is also divided into
two parts. This fuel tank design causes higher
pressures inside the tank than other vehicles so
fuel spillage is possible by trying to top off the
fuel tank after automatic shutoff.
The fuel tank pressure is higher when the vehicle
is hot, especially if the tank is more than half full.
If the cap is opened when the vehicle is hot, it
may cause fuel spray and there may be a hissing
noise. Open the cap slowly, releasing the
pressure from the tank gradually. Also, if the
vehicle is refueled when the vehicle is hot, the
fuel pump may automatically shut off before the
tank is full. This does not indicate that there is a
malfunction. Refuel slowly or refuel after the
vehicle has cooled.
ENGINE SPEED IS RESTRICTED
GASOLINE SMELL
To help protect the engine, the maximum engine
speed is automatically controlled in the following
conditions:
The fuel temperature is higher when the vehicle
is hot. This may cause a gasoline smell from the
vehicle. This does not indicate that there is a
malfunction. The smell will go away when the
fuel temperature has cooled.
OUTSIDE TEMPERATURE DISPLAY
INDICATES HIGHER TEMPERATURE
.
Revving the engine with the shift lever in the
P or &
N position: The maximum engine
&
speed is 5,000 RPM
.
Revving the engine when the engine oil is at
a low (below 328F (08C)) or extremely high
(over 2758F (1358C)) temperature: The
maximum engine speed is 4,000 RPM (The
M position will automatically change to the
&
A position.)
&
Heat from the engine compartment, radiator and
intercoolers can affect the outside temperature
display. The outside temperature display may
indicate a higher than actual temperature while
driving or stopped. This is normal.
ENGINE OUTPUT
IDLE SPEED IS NOT STEADY
High altitude
The idle speed may not be steady when the
engine compartment is extremely hot. This is
normal. The engine speed will be steady when
the engine cools down.
In this case, the Malfunction Indicator Light (MIL)
may come on. After a few driving trips, the MIL
should turn off. If the light remains on after a few
driving trips, have the vehicle inspected by a
GT-R certified NISSAN dealer.
To protect the engine, engine output is controlled so that it does not increase at altitudes
3,281 ft (1,000 m) or higher.
Engine output according to the
coolant temperature
The engine output is controlled at a low level
when the engine coolant temperature is lower
than approximately 1588F (708C) or higher than
2308F (1108C). This is not a malfunction.
If the temperature is lower than approximately
GT-R Overview GTR-23
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(32,1)
1588F (708C), drive the vehicle until it reaches
normal operating temperature. If the temperature
is higher than 2308F (1108C), perform cooldown driving procedure. (
“Cool down”
page GTR-13) When the temperature of the
engine coolant is between 1588F (708C) and
2308F (1108C), the engine output returns to
normal.
noise. Contact a GT-R certified NISSAN
dealer.
.
UNEVEN WEAR OF TIRES
The GT-R is equipped with high performance,
low profile, run-flat tires that are optimized for
performance and handling. The life of these tires
will be less than those of tires installed on a
typical vehicle, and you are likely to experience
uneven tire wear and tire noise regardless of the
type of tire used.
NOISES ARE HEARD WHILE DRIVING
.
The GT-R brake pads use material that
provides a high amount of braking power
even in high temperatures. This material can
cause an intermittent screeching noise just
before the vehicle comes to a stop when the
brakes are gently applied. The noise decreases as the brake pads wear. However,
the additional brake pad break-in or replacing the cross spring may decrease the
GTR-24
.
A screeching noise may be heard when the
brake pedal is depressed:
— When driving the vehicle for the first time
in the morning,
— After leaving the vehicle parked for
extended periods of time, or
— When the vehicle is damp following rain
showers or washing the vehicle.
These sounds are normal. The noise is
caused when the brake pads absorb moisture, and the noise stops after the brake is
applied several times.
A screeching noise may also be heard when
the brake pedal is depressed:
— When repeatedly applying gentle braking, especially on a curve at a low speed,
or
— When the brake rotors have circular
scores with the brake temperature high.
WARNING
Follow the instructions below when
parking the vehicle to help prevent the
brake rotor and brake pads from rusting together. Failure to follow the
instructions could cause the rotor and
pads to rust together. If the rotor and
pads rust together, there may be a
popping noise and some vibration
when the vehicle is driven, a wheel
may not roll correctly, or the brake pads
could be damaged. If the pads are
damaged, this may reduce the effectiveness of the brake system which
could cause a collision, serious personal injury or death.
.
The GT-R uses brake pad materials that
have high metallic content. The brake pad
material helps maintain braking performance
in a wide range of weather and driving
conditions.
For the first 3,000-6,000 miles (5,00010,000 km) of the vehicle’s service life,
and for the first 3,000-6,000 miles (5,00010,000 km) after a brake replacement, the
brake pad to brake rotor clearance is very
small. When parking, apply the parking
P
brake and move the shift lever to the &
position. Idle the engine for more than 20
seconds without depressing the brake
pedal. This allows the brake pads to move
away from the rotor so the pad does not
contact the rotor.
GT-R Overview
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(33,1)
Additionally, the brakes must be dry before
parking the vehicle after driving on wet roads
or after washing the vehicle. If the roads are
wet, lightly apply the brakes for a short
distance before parking the vehicle to dry
the brakes. After washing the vehicle, dry the
brakes by driving on a dry road for a few
miles and apply the brakes normally based
on traffic and road conditions.
The metallic brake pads and brake disc rotor
may rust together when the brakes are not
applied:
— If the vehicle is not idled for 20 seconds
without the brakes applied, or if the
brakes are applied when the vehicle is
shut off, the rotor and pads can rust
together, even when the brake pads are
dry.
— If the brakes are wet when the vehicle is
parked and the parking brake is applied
for a long time.
— The hill start assist system can apply the
brakes even if the brake pedal is not
depressed. The brake pads and rotors
can rust together if the parking procedure previously described is not followed.
Contact a GT-R certified NISSAN dealer if
the brake pads and brake rotor have rusted
together.
.
When the brake disc rotor undergoes
thermal expansion, a ticking noise may be
heard from the engaging portion of the
wheel and the brake disc rotor. This does
not indicate that there is a malfunction. The
noise will reduce when the temperature
decreases.
.
In addition to noise resulting from uneven
tire wear discussed in the previous section,
the GT-R tires are more rigid than a typical
passenger car tire and are made from a
specially formulated rubber to maximize the
vehicle’s performance capabilities. These
characteristics cause the GT-R tires to have
more road noise than a typical passenger
car tire. This road noise is normal.
.
Due to the performance capabilities and
requirements of the GT-R, the sequential 6speed dual clutch transmission is unlike a
typical automatic transmission. You will likely
hear mechanical sounds from the transmission, particularly at slow speeds and at idle.
This condition is normal.
NOTICE
To help reduce the possibility of the
rotors and brake pads rusting:
Have the brake pads and/or rotors
quenched when the brake pads are
replaced. For detailed information
about quenching, contact a GT-R certified NISSAN dealer.
After quenching the brake pads and/or
rotors, apply a brake of 0.5G to stop the
vehicle 6-7 times at least once a week
in a safe location. G-force can be
checked on the multi function display.
Refer to the separate Multi Function
Display Owner’s Manual.
.
To maintain steady braking performance in
both extremely high and low temperatures,
the gap between the brake pad and caliper
is larger than normal and large-size brake
pads are used. When driving over a bump, a
light rattling sound may be heard from the
brake pad. This does not indicate that there
is a malfunction.
GT-R Overview GTR-25
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(34,1)
driving, or through the continued use of the
brakes, the disc rotors must be replaced.
BRAKE SYSTEM INFORMATION
Cracks on brake pad
The friction material of the GT-R disc brake pad
is bonded to the pad backing plate more
strongly than conventional brake pads to withstand the high brake temperatures. The friction
material and backing plate expand due to heat at
different rates. Some cracks may be on the
surface of the friction material due to the
differences in expansion rates and the strong
bond between the friction material and backing
plate. The cracks do not indicate the brake pads
need to be replaced. However, depending on
the condition of the cracks, the pads may need
to be replaced. Contact a GT-R certified
NISSAN dealer.
GTR-26
Brake dust
This vehicle is equipped with high performance
brakes, and the characteristics of the brake pad
material may cause more brake dust than other
vehicles. NISSAN recommends a wheel coating
that helps prevent the brake dust from sticking
to the wheels. Contact a GT-R certified NISSAN
dealer for more details.
CHANGE OF SURFACE COLOR OF
TITANIUM MUFFLER (if so
equipped)
Cracks on the disc rotors
When the brake is repeatedly applied at high
loads during the cold season, small cracks of
approximately 0.12 in (3 mm) long may appear
A . This is due to
around the cross drilled holes *
the temperature differential that occurs because
the surfaces of the disc rotors become hot while
the inside of the rotor is still cold. However, this
poses no problem in terms of brake performance, and does not indicate a malfunction. The
brakes do not need to be replaced.
However, if the cracks extend to 0.16 in (4 mm)
or longer after repeated application of the
brakes at high loads during high performance
Genuine titanium mufflers are made of titanium
alloy. The surface color will change depending
on the driving conditions, which is not unusual.
Prior to shipping from factory, all vehicles
receive balance aligning for engine, transmission, and clutch, as well as quench driving of
brake pads and rotors. As a result, the muffler
surface color may differ depending on the
vehicle.
GT-R Overview
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(35,1)
DUAL CLUTCH TRANSMISSION
SOUND HEARD AROUND TITANIUM
MUFFLER (if so equipped)
When stopping the engine (rapid cooling), you
may hear a metal-rubbing sound or unusual
ticking sound because of the differential thermal
expansion between the inner and outer pipes of
the muffler. This is not a malfunction. The sound
will decrease when the temperature lowers.
DRY CARBON FIBER PARTS (if so
equipped)
Roughness or uneven surfaces of dry
carbon fiber parts and fiber twists
The surfaces of the dry carbon fiber parts are
lightly coated like a race car so that you can feel
the proper texture of real carbon, which may feel
rough. This is normal.
The GT-R dual clutch transmission is a newlydeveloped system that uses an electronically
controlled multiple-disc wet clutch attached to
the highly efficient manual transmission. This
transmission has two driving modes.
.
A position (Automatic gearshift):
&
.
Gear clearances
.
Ultralight flywheel
. Dry sump lubrication
These noises do not indicate that there is a
malfunction.
allows automatic shifting of the manual
transmission.
.
M position (Manual gearshift):
&
allows quick shifting of the manual transmission.
NOTE:
When starting or driving on a steep uphill
M position and operate
grade, shift to the &
the paddle shifter to shift down to 1st gear
similar to a manual transmission vehicle.
The GT-R dual clutch transmission was developed specifically to maximize vehicle performance and driving enjoyment. The GT-R
transmission components were designed using
different engineering standards than typical
passenger car transmissions. Because of this,
the GT-R has different operating characteristics,
and various rattle noises may be heard during
some driving conditions because of the following items:
GT-R Overview GTR-27
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(36,1)
TRANSMISSION OPERATION CHARACTERISTICS
Mechanism
Operation characteristics
.
Base Manual transmission
.
.
.
.
Multiple disc wet clutch
.
.
Electronic oil pressure
control
Changing modes
Mechanical Limited Slip
Differential (LSD)
GTR-28
The GT-R transmission design is different from transmissions used in conventional passenger cars. The GT-R uses a transmission gear
design, light flywheel and a dry sump lubrication system to provide maximum vehicle performance. Because the GT-R Transmission design
is different, noises may be louder. When the transmission temperature is high, rattling, shaking and jarring noises may be heard.
Clattering noises may be heard while shifting.
Appropriate gaps are provided between gears to achieve smooth gear rotation and steady tooth surface lubrication under the high-load
driving condition. However, this causes a rattling noise.
R to &
A ↔&
A ↔&
R position before the vehicle stops, you may not be able to shift gear
M position, or &
M to &
If the shift lever is moved from &
or it may take longer to shift gear. Make sure to depress the brake pedal and check that the vehicle has stopped before shifting.
R or &
A ↔&
M position, be sure to firmly depress the brake pedal. The vehicle may
When stopping the vehicle with the shift lever in the &
slowly move if the brake pedal is not depressed.
Avoid depressing the brake and accelerator pedals at the same time. Depressing the brake and accelerator pedals at the same time could
cause the clutch to overheat and accelerate deterioration.
When the vehicle is stopped on a hill, do not hold the vehicle in place by depressing the accelerator pedal. Doing so may cause the clutch
to overheat and result in transmission damage. Use the brakes to prevent the vehicle from moving.
The following conditions are caused due to changes in fluid viscosity as a result of temperature changes.
. When the transmission oil is extremely cold or extremely hot, the transmission may feel like it is slipping during shifts or there may be hard
shifts. This is normal. Transmission shifting should return to normal when the transmission oil returns to normal operating temperatures.
. When the transmission oil temperature is extremely cold, the time required to run a system check may increase. During the system check,
P position. Move the shift lever after turning off the system check display. Also, it is normal to hear clicking
the shift lever must stay in the &
noises during the transmission systems check.
.
.
M position may result in shift shock and jerkiness when starting or shifting.
The higher shift speeds in the &
M position is available when the engine speed is high. However, the
The quickest shifting in the R mode with the transmission in the &
transmission may shift more slowly when the engine speed is low.
If the vehicle accelerates from a stop with the steering wheel turned half a turn in cold temperatures, the inner wheel tire may slip and some
noise or vibration may be heard. This phenomenon occurs because the viscosity of the differential oil becomes thicker and the Limited Slip
Differential (LSD) operates with increasing load. When the steering wheel is returned to the straight ahead position or the differential oil warms
up, the noise and vibration decrease.
GT-R Overview
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(37,1)
Mechanism
Electronically-controlled
All-wheel drive (AWD)
Ultralight flywheel
Operation characteristics
If the vehicle accelerates from a stop with the steering wheel turned half a turn in cold temperatures, it may be hard to move the vehicle when
the accelerator pedal is depressed. This phenomenon is unique to AWD vehicles and is caused by the speed difference between the front and
rear wheel. This is not a malfunction. Resolve the phenomenon by returning the steering wheel to the straight ahead position. You can also
alleviate the phenomenon by operating the transmission set up switch and using 2WD drive only when the steering wheel is turned significantly
at a low speeds. Normally, the vehicle will not switch to 2WD drive when the set up switch is operated. (
“Tight corner braking
phenomenon” page 5-43)
. An ultralight flywheel is provided to achieve rapid engine response to the accelerator pedal operation. The engine rotation fluctuations
become larger than conventional vehicles. Rattling, shaking or jarring noises may be heard when idling or driving at a low speed.
. Rattling noises may be heard when the engine is started or stopped.
GT-R Overview GTR-29
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(38,1)
MEMO
GTR-30
GT-R Overview
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(39,1)
0 Illustrated table of contents
Seats, seat belts and Supplemental Restraint
System (SRS) ...........................................................................
Front ......................................................................................
Rear .......................................................................................
Exterior front ..............................................................................
Exterior rear ...............................................................................
0-2
0-2
0-3
0-4
0-5
Passenger compartment ........................................................ 0-6
Cockpit ....................................................................................... 0-7
Instrument panel ...................................................................... 0-8
Meters and gauges ................................................................. 0-9
Engine compartment ........................................................... 0-10
Warning and indicator lights ............................................. 0-11
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(40,1)
SEATS, SEAT BELTS AND
SUPPLEMENTAL RESTRAINT
SYSTEM (SRS)
FRONT
1.
2.
3.
4.
5.
6.
7.
8.
0-2
Seat belt (Page 1-6)
Rear seat walk-in lever (P.1-5)
Roof-mounted curtain side-impact supplemental
air bag system (P.1-34)
Supplemental front-impact air bags (P.1-34)
Seat belt pretensioner (P.1-46)
Front seat-mounted side-impact supplemental
air bag system (P.1-34)
Occupant classification sensor (pattern sensor)
(P.1-40)
Front seats (P.1-3)
Illustrated table of contents
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(41,1)
REAR
1.
2.
3.
Rear seats
— Child restraint installation (P.1-15)
Child restraint anchor points (for top tether strap
child restraint) (P.1-19)
LATCH (Lower Anchors and Tethers for CHildren) system (P.1-17, P.1-26, P.1-30)
Illustrated table of contents 0-3
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(42,1)
EXTERIOR FRONT
ITEMS
GENUINE PARTS
Road wheel
Genuine road wheel specific to
GT-R
Tire*1
Genuine tire specific to GT-R
Genuine brake pad specific to
GT-R
Genuine brake disc rotor speBrake disc rotor*2 cific to GT-R
Brake pad*2
*1:
*2:
1.
2.
3.
4.
5.
6.
0-4
Hood (P.3-17)
Windshield wiper and washer (P.2-48, P.8-22)
Doors (P.3-2, P.3-4, P.3-8)
Outside mirrors (P.3-27)
Power windows (P.2-60)
Daytime running light (P.2-50)
7.
8.
Headlight and turn signal (P.2-50, P.8-29)
Tires and wheels (P.5-4, P.6-3, P.8-32, P.9-9)
When tire replacement is required, replacing
tires as a set of four with new tires is
recommended. However, if a tire is punctured
or damaged, it may be possible to replace only
the damaged tire. Determining whether one tire
or a complete set of tires should be replaced is
based on a number of factors including tire wear
and condition. Contact your GT-R certified
NISSAN dealer. They can recommend if an
individual tire or a complete set should be
replaced.
“Replacement of brake pads and disc
rotors” page GTR-5
Genuine NISSAN Brake Fluid R35 Special II is
the factory fill brake fluid. The Vehicle Dynamic
Control (VDC) unit and other related parts were
specially designed for this brake fluid. NISSAN
cannot ensure proper operation of the vehicle if
other brake fluid is used.
Illustrated table of contents
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(43,1)
EXTERIOR REAR
ITEMS
Fuel
*1:
1.
2.
3.
4.
5.
6.
High-mounted stop light (P.8-29)
Trunk (P.3-8, P.3-19)
Rear window defroster (P.2-50)
Satellite antenna*
Rear view camera*
Rear combination light (P.8-29)
7.
*:
GT-R SPECIFIED FUEL
Unleaded premium gasoline with an
octane rating of at least 93 AKI (AntiKnock Index) number (Research octane
number 98)*1
Use unleaded premium gasoline with an octane
rating of at least 93 AKI (Anti- Knock Index)
number (Research octane number 98) to maximize vehicle performance. If 93 AKI number
(Research octane number 98) premium gasoline
is not available, you may use unleaded premium
gasoline with an octane rating of at least 91 AKI
number (Research octane number 96), but you
may notice a decrease in performance.
Fuel-filler door (P.3-23, P.9-4)
Refer to the separate Multi Function Display
Owner’s Manual.
A : Except for NISMO models
*
B : NISMO models
*
Illustrated table of contents 0-5
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(44,1)
PASSENGER COMPARTMENT
11.
12.
*:
1.
2.
3.
4.
5.
6.
0-6
Coat hooks (P.2-59)
Inside lock knob (P.3-5)
Interior light control switch (P.2-62)
Map lights (P.2-62)
Sun visors (P.3-26)
Sunglasses holder (P.2-57)
7.
8.
9.
10.
Window lock button (P.2-61)
Power door lock switch (P.3-5)
Refer to the separate Multi Function Display
Owner’s Manual.
Inside rearview mirror (P.2-64, P.3-26)
Center console box (P.2-59)
— USB memory operation*
— iPod® player operation*
Cup holders (P.2-56)
Power window switches (P.2-60)
Illustrated table of contents
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(45,1)
COCKPIT
11.
12.
13.
14.
15.
*:
1.
2.
3.
4.
5.
Headlight and turn signal switch (P.2-50)
Paddle shifters (P.5-15)
Steering-wheel-mounted controls (left side)*
Meters and gauges (P.2-5)
Steering-wheel-mounted controls (right side)
— MRK (Mark) switch*
— Cruise control (P.5-34)
6.
7.
8.
9.
10.
Horn (P.2-54)
Tilting/telescopic steering wheel lever (P.3-25)
Push-button ignition switch (P.5-10)
Parking brake (P.5-33, P.5-46)
Shift lever (P.5-15)
Refer to the separate Multi Function Display
Owner’s Manual.
Wiper and washer switch (P.2-48)
VDC, transmission and suspension set up
switches (P.5-25)
Trunk lid release switch (P.3-19)
Hood release handle (P.3-17)
Intelligent Key port (P.5-12)
Illustrated table of contents 0-7
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(46,1)
INSTRUMENT PANEL
13.
*:
1.
2.
3.
4.
5.
6.
0-8
Outside mirror control switch (P.3-27)
Center dial*
Audio system*
Heater and air conditioner*
Multi function display*
Hazard warning flasher switch (P.6-2)
7.
8.
9.
10.
11.
12.
Trunk release power cancel switch (P.3-20)
Refer to the separate Multi Function Display
Owner’s Manual.
Glove box (P.2-58)
Fuse box cover (P.8-25)
Power outlet (P.2-55)
Rear window defroster switch (P.2-50)
Front passenger air bag status light (P.1-41)
CD/DVD slot*
Illustrated table of contents
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(47,1)
METERS AND GAUGES
NOTE:
. Meters and gauges will illuminate
when the ignition switch is pushed to
the ON position.
.
1.
2.
3.
4.
5.
6.
Trip A/B reset switch (P.2-6)
Speedometer (P.2-6)
Tachometer (P.2-7)/Upshift indicator (P.2-9)
Transmission position indicator (P.2-9)
Engine coolant temperature gauge (P.2-7)
ENTER switch (P.2-15)
7.
8.
9.
10.
11.
The needle indicators may move
slightly after the ignition switch is
pushed to the OFF position. This does
not indicate that there is a malfunction.
Instrument brightness control switch (P.2-11)
Vehicle information display (P.2-12)
Odometer/twin trip odometer (P.2-6)
Fuel gauge (P.2-8)
NEXT switch (P.2-15)
Illustrated table of contents 0-9
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(48,1)
ENGINE COMPARTMENT
ITEMS
Mobil 1 (0W-40)*1
Transmission oil
Genuine NISSAN Transmission
Oil R35 Special
Differential oil
(front and rear)
Brake fluid
*1:
*2:
1.
2.
3.
4.
5.
6.
Fuse/fusible link holder (P.8-25)
Battery (P.8-17)
Engine oil filler cap (P.8-13)
Engine oil dipstick (P.8-13)
Brake fluid reservoir (P.8-15)
Air cleaner (P.8-21)
7.
8.
9.
10.
11.
GT-R SPECIFIED FLUIDS
Engine oil
Differential Oil R35 COMPETITION type 2189E
Genuine NISSAN Brake Fluid
R35 Special II*2
Mobil 1 (0W-40) (100% synthetic) is the factory
fill oil. The VR38 engine with its plasma-sprayed
bores was developed using this oil. NISSAN
cannot ensure proper engine operation and
durability if other 0W-40 synthetic oil is used.
If Mobil 1 (0W-40) is not available, Mobil 1
(10W-40) (100% synthetic) may be used;
however, some performance loss may be
noticed.
Genuine NISSAN Brake Fluid R35 Special II is
the factory fill brake fluid. The Vehicle Dynamic
Control (VDC) unit and other related parts were
specially designed for this brake fluid and
NISSAN cannot ensure proper operation of the
vehicle if other brake fluid is used.
Power steering fluid reservoir (P.8-14)
Radiator filler cap (P.8-10)
Coolant reservoir cap (pressure type) (P.8-10)
Coolant reservoir (P.8-10)
Window washer fluid reservoir (P.8-16)
0-10 Illustrated table of contents
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(49,1)
WARNING AND INDICATOR LIGHTS
Warning
light
Name
Page
All-Wheel Drive (AWD) warning
light
2-25
Anti-lock Braking System
(ABS) warning light
2-26
Warning
light
Name
Page
Vehicle Dynamic Control (VDC)
warning light
2-31
Indicator
light
Name
Page
Cruise main switch indicator
light
2-31
Cruise set switch indicator light
2-31
Exterior light indicator
2-31
Front passenger air bag status
light
2-31
High beam indicator light
2-31
Brake warning light
2-26
Charge warning light
2-27
Engine oil pressure warning
light
2-27
Malfunction Indicator Light
(MIL)
2-31
Intelligent Key warning light
2-27
Turn signal/hazard indicator
lights
2-32
Low tire pressure warning light
2-27
Vehicle Dynamic Control (VDC)
off indicator light
2-32
Master warning light
2-29
Seat belt warning light
2-29
Supplemental air bag warning
light
2-29
Transmission warning light
2-30
Illustrated table of contents 0-11
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(50,1)
MEMO
0-12 Illustrated table of contents
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(51,1)
1 Safety — Seats, seat belts and supplemental restraint system
Seats ........................................................................................... 1-2
Front seats ........................................................................... 1-3
Head restraints/headrests ...................................................... 1-5
Seat belts ................................................................................... 1-6
Precautions on seat belt usage ...................................... 1-6
Pregnant women ................................................................ 1-9
Injured persons ................................................................... 1-9
Three-point type seat belt with retractor ..................... 1-9
Seat belt extenders ......................................................... 1-12
Seat belt maintenance ................................................... 1-13
Child safety ............................................................................. 1-13
Infants ................................................................................. 1-14
Small children ................................................................... 1-14
Larger children ................................................................. 1-14
Child restraints ....................................................................... 1-15
Precautions on child restraints .................................... 1-15
Lower Anchors and Tethers for CHildren
System (LATCH) ............................................................. 1-17
Rear-facing child restraint installation
using LATCH .................................................................. 1-19
Rear-facing child restraint installation using the
seat belts ......................................................................... 1-21
Forward-facing child restraint installation
using LATCH .................................................................. 1-24
Forward-facing child restraint installation using the
seat belts ......................................................................... 1-26
Booster seats ................................................................. 1-30
Supplemental restraint system .......................................... 1-34
Precautions on supplemental restraint system ...... 1-34
NISSAN Advanced Air Bag System
(front seats) .................................................................... 1-40
Front seat-mounted side-impact supplemental
air bag and roof-mounted curtain side-impact
supplemental air bag systems ................................... 1-45
Seat belts with pretensioners (front seats) ............ 1-46
Supplemental air bag warning labels ...................... 1-47
Supplemental air bag warning light ......................... 1-47
Repair and replacement procedure ......................... 1-48
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(52,1)
SEATS
.
The seatback should not be reclined
any more than needed for comfort.
Seat belts are most effective when
the passenger sits with their back
straight up and contacting the seat.
If the seatback is reclined, the risk
of sliding under the lap belt and
being injured is increased.
CAUTION
When adjusting the seat positions, be
sure not to contact any moving parts to
avoid possible injuries or damage.
well back in the seat with both feet
on the floor and adjust the seat
properly. (
“Precautions on seat
belt usage” page 1-6)
WARNING
.
.
1-2
Do not ride in a moving vehicle
when the seatback is reclined. This
can be dangerous. The shoulder belt
will not be against your body. In an
accident, you could be thrown into it
and receive neck or other serious
injuries. You could also slide under
the lap belt and receive serious
internal injuries.
For the most effective protection
when the vehicle is in motion, the
seat should be upright. Always sit
.
After adjustment, gently rock in the
seat to make sure it is securely
locked.
.
Do not leave children unattended
inside the vehicle. They could unknowingly activate switches or controls. Unattended children could
become involved in serious accidents.
NOTICE
Make sure the front seatback does not
contact the rear seat when reclining the
seat. When the front seat is reclined to
the rearmost position, it may contact
the rear seat. This may cause an
indentation in the seatback.
Safety — Seats, seat belts and supplemental restraint system
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(53,1)
FRONT SEATS
Front power seat adjustment
Operating tips
.
The power seat motor has an auto-reset
overload protection circuit. If the motor
stops during operation, wait 30 seconds,
then reactivate the switch.
.
Do not operate the power seat switch for a
long period of time when the engine is off.
This will discharge the battery.
Safety — Seats, seat belts and supplemental restraint system 1-3
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(54,1)
Seat Adjustment
Switch
Operation
Move the switch A forward or backward until the desired seat position is obtained.
Forward and backward
A
*
Reclining
A
*
Seat lifter (front)
B
*
Push the switch up or down B
Seat lifter (rear)
A
*
Move the switch A
1-4
Location
*
Driver’s and front
passenger’s seats
Turn the switch A forward and backward until the desired seatback angle is
obtained.
The reclining feature allows adjustment of the seatback for occupants of different sizes
for added comfort and to help obtain proper seat belt fit. (
“Precautions on seat
belt usage” page 1-6)
Also, the seatback can be reclined to allow occupants to rest when the vehicle is
P position with the parking brake fully applied.
stopped and the transmission is in the &
*
*
*
to raise or lower the front portion of the seat.
up or down to raise or lower the rear portion of the seat.
Driver’s seat
Safety — Seats, seat belts and supplemental restraint system
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(55,1)
HEAD RESTRAINTS/HEADRESTS
seat position.
WARNING
CAUTION
.
When returning the seat to its
original position, confirm that the
seat and seatback are locked properly.
.
Be careful not to pinch your hand or
foot or bump your head when operating the walk-in seat.
NOTICE
Rear seat walk-in
This feature makes it easier to get in and out of
the rear seat. Use the following procedure when
getting in and out of the rear seat.
1 , hold the knob *
2 , and
1. Pull up the lever *
tilt the seatback forward.
A to slide
2. Use the seat adjustment switch *
the seat forward to a position where it will be
easier to enter or exit the rear seats. Fold the
shoulder belt guide for easier access to the
rear seat.
To return the seatback to its original position,
2 , raise the seatback, and use
hold the knob *
A to adjust the
the seat adjustment switch *
Do not place any objects near the
seatback of the front seats. They may
be pinched and damaged.
Head restraints/headrests supplement
the other vehicle safety systems. They
may provide additional protection
against injury in certain rear end collisions.
Head restraints/headrests must be adjusted properly, as specified in this
section. Check the adjustment after
someone else uses the seat. Failure to
follow these instructions can reduce the
effectiveness of the head restraints/
headrests. This may increase the risk
of serious injury or death in a collision.
Safety — Seats, seat belts and supplemental restraint system 1-5
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(56,1)
SEAT BELTS
PRECAUTIONS ON SEAT BELT
USAGE
The illustration shows the seating positions
equipped with head restraint/headrest.
Indicates the seating position is equipped
with a head restraint.
+ Indicates the seating position is not equipped
with a head restraint or headrest.
Your vehicle is equipped with integrated head
restraints/headrests.
Proper adjustment:
Properly position the head restraint by adjusting
the front seat so that the top of the seat is as
upright as possible.
1-6
If you are wearing your seat belt properly
adjusted, and you are sitting upright and well
back in your seat with both feet on the floor, your
chances of being injured or killed in an accident
and/or the severity of injury may be greatly
reduced. NISSAN strongly encourages you and
all of your passengers to buckle up every time
you drive, even if your seating position includes a
supplemental air bag.
Most U.S. states and Canadian provinces
or territories specify that seat belts be
worn at all times when a vehicle is being
driven.
Safety — Seats, seat belts and supplemental restraint system
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(57,1)
WARNING
.
Every person who drives or rides in
this vehicle should use a seat belt at
all times. Children should be properly restrained in the rear seat and,
if appropriate, in a child restraint.
.
The seat belt should be properly
adjusted to a snug fit. Failure to do
so may reduce the effectiveness of
the entire restraint system and increase the chance or severity of
injury in an accident. Serious injury
or death can occur if the seat belt is
not worn properly.
.
Always route the shoulder belt over
your shoulder and across your
chest. Never put the belt behind
your back, under your arm or across
your neck. The belt should be away
from your face and neck, but not
falling off your shoulder.
.
Position the lap belt as low and
snug as possible AROUND THE
HIPS, NOT THE WAIST. A lap belt
worn too high could increase the
risk of internal injuries in an accident.
Safety — Seats, seat belts and supplemental restraint system 1-7
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(58,1)
.
Be sure the seat belt tongue is
securely fastened to the proper
buckle.
.
Do not wear the seat belt inside out
or twisted. Doing so may reduce its
effectiveness.
.
Do not allow more than one person
to use the same seat belt.
.
Never carry more people in the
vehicle than there are seat belts.
.
If the seat belt warning light glows
continuously while the ignition is
turned ON with all doors closed and
all seat belts fastened, it may indicate a malfunction in the system.
Have the system checked by a GT-R
certified NISSAN dealer.
.
No changes should be made to the
seat belt system. For example, do
not modify the seat belt, add material, or install devices that may
change the seat belt routing or
tension. Doing so may affect the
operation of the seat belt system.
Modifying or tampering with the
seat belt system may result in
serious personal injury.
1-8
.
Once a seat belt pretensioner has
activated, it cannot be reused and
must be replaced together with the
retractor. See a GT-R certified
NISSAN dealer.
.
Removal and installation of the
pretensioner system components
should be done by a GT-R certified
NISSAN dealer.
.
All seat belt assemblies, including
retractors and attaching hardware,
should be inspected after any collision by a GT-R certified NISSAN
dealer. NISSAN recommends that
all seat belt assemblies in use
during a collision be replaced unless the collision was minor and the
belts show no damage and continue
to operate properly. Seat belt assemblies not in use during a collision should also be inspected and
replaced if either damage or improper operation is noted.
.
All child restraints and attaching
hardware should be inspected after
any collision. Always follow the
restraint manufacturer’s inspection
instructions and replacement re-
commendations. The child restraints
should be replaced if they are
damaged.
Safety — Seats, seat belts and supplemental restraint system
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(59,1)
PREGNANT WOMEN
NISSAN recommends that pregnant women use
seat belts. The seat belt should be worn snug,
and always position the lap belt as low as
possible around the hips, not the waist. Place
the shoulder belt over your shoulder and across
your chest. Never run the lap/shoulder belt over
your abdominal area. Contact your doctor for
specific recommendations.
INJURED PERSONS
NISSAN recommends that injured persons use
seat belts. Check with your doctor for specific
recommendations.
THREE-POINT TYPE SEAT BELT
WITH RETRACTOR
WARNING
.
Every person who drives or rides in
this vehicle should use a seat belt at
all times.
.
Do not ride in a moving vehicle
when the seatback is reclined. This
can be dangerous. The shoulder belt
will not be against your body. In an
accident, you could be thrown into it
and receive neck or other serious
injuries. You could also slide under
the lap belt and receive serious
internal injuries.
.
For the most effective protection
when the vehicle is in motion, the
seat should be upright. Always sit
well back in the seat with both feet
on the floor and adjust the seat belt
properly.
.
Do not allow children to play with
the seat belts. Most seating positions are equipped with Automatic
Locking Retractor (ALR) mode seat
belts. If the seat belt becomes
wrapped around a child’s neck with
the ALR mode activated, the child
can be seriously injured or killed if
the seat belt retracts and becomes
tight. This can occur even if the
vehicle is parked. Unbuckle the seat
belt to release the child. If the seat
belt can not be unbuckled or is
already unbuckled, release the child
by cutting the seat belt with a
suitable tool (such as a knife or
scissors) to release the seat belt.
Safety — Seats, seat belts and supplemental restraint system 1-9
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(60,1)
the retractor.
Fastening the seat belts
1. Adjust the seat. (
“Seats” page 1-2)
2. Slowly pull the seat belt out of the retractor
and insert the tongue into the buckle until
you hear and feel the latch engage.
. The retractor is designed to lock
during a sudden stop or on impact. A
slow pulling motion permits the belt
to move, and allows you some freedom of movement in the seat.
. If the seat belt cannot be pulled
from its fully retracted position,
firmly pull the belt and release it.
Then smoothly pull the belt out of
3. Position the lap belt portion low and snug
on the hips as shown.
4. Pull the shoulder belt portion toward the
retractor to take up extra slack. Be sure the
shoulder belt is routed over your shoulder
and across your chest.
The three-point type seat belts for the front
passenger and rear seats have two modes of
operation:
.
Emergency Locking Retractor (ELR)
. Automatic Locking Retractor (ALR)
The Emergency Locking Retractor (ELR) mode
allows the seat belt to extend and retract to
allow the driver and passengers some freedom
1-10 Safety — Seats, seat belts and supplemental restraint system
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(61,1)
of movement in the seat. The ELR locks the seat
belt when the vehicle slows down rapidly or
during impacts.
may be injured in an accident or sudden
stop.
The Automatic Locking Retractor (ALR) mode or
child restraint mode locks the seat belt for child
restraint installation.
When the ALR mode is activated the seat belt
cannot be extended again until the seat belt
tongue is detached from the buckle and fully
retracted. The seat belt returns to the ELR mode
after the seat belt is fully retracted.
(
“Child restraints” page 1-15)
The ALR mode should be used only for
child restraint installation. During normal
seat belt use by an occupant, the ALR
mode should not be activated. If it is
activated it may cause uncomfortable seat
belt tension. It can also change the operation of the front passenger air bag.
(
“Front passenger air bag and status
light” page 1-41)
Unfastening the seat belts
To unfasten the seat belt, push the button on the
buckle. The seat belt automatically retracts.
Checking seat belt operation
Seat belt retractors are designed to lock seat
belt movement by two separate methods:
.
WARNING
When fastening the seat belts, be
certain that seatbacks are completely
secured in the latched position. If they
are not completely secured, passengers
When the belt is pulled quickly from the
retractor.
. When the vehicle slows down rapidly.
To increase your confidence in the seat belts,
check the operation as follows:
.
Grasp the shoulder belt and pull forward
Safety — Seats, seat belts and supplemental restraint system 1-11
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(62,1)
quickly. The retractor should lock and
restrict further belt movement.
If the retractor does not lock during this check or
if you have any question about seat belt
operation, see a GT-R certified NISSAN dealer.
SEAT BELT EXTENDERS
If, because of body size or driving position, it is
not possible to properly fit the lap-shoulder belt
and fasten it, an extender that is compatible with
the installed seat belts is available that can be
purchased. The extender adds approximately 8
in (200 mm) of length and may be used for either
the driver or front passenger seating position.
See a GT-R certified NISSAN dealer for
assistance with purchasing an extender if an
extender is required.
WARNING
Shoulder belt arm (for front seats)
Before fastening the seat belt, adjust the
shoulder belt arm to the lock position where
the belt fits snugly on the shoulder. The arm can
also be folded down to allow rear seat
passengers easier access.
.
Only NISSAN seat belt extenders,
made by the same company which
made the original equipment seat
belts, should be used with the
NISSAN seat belts.
.
Adults and children who can use the
standard seat belt should not use an
extender. Such unnecessary use
could result in serious personal
injury in the event of an accident.
.
Never use seat belt extenders to
install child restraints. If the child
restraint is not secured properly, the
child could be seriously injured in a
Pulling the arm forward will allow an easy access
to the belt.
1-12 Safety — Seats, seat belts and supplemental restraint system
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(63,1)
CHILD SAFETY
collision or a sudden stop.
SEAT BELT MAINTENANCE
.
To clean the seat belt webbing, apply a
mild soap solution or any solution recommended for cleaning upholstery or carpets.
Then, wipe with a cloth and allow the seat
belts to dry in the shade. Do not allow the
seat belts to retract until they are completely
dry.
.
If dirt builds up in the shoulder belt
guide of the seat belt anchors, the seat
belts may retract slowly. Wipe the shoulder
belt guide with a clean, dry cloth.
.
Periodically check to see that the seat
belt and the metal components such as
buckles, tongues, retractors, flexible wires
and anchors work properly. If loose parts,
deterioration, cuts or other damage on the
webbing is found, the entire seat belt
assembly should be replaced.
systems:
WARNING
Do not allow children to play with the
seat belts. Most seating positions are
equipped with Automatic Locking Retractor (ALR) mode seat belts. If the
seat belt becomes wrapped around a
child’s neck with the ALR mode activated, the child can be seriously injured
or killed if the seat belt retracts and
becomes tight. This can occur even if
the vehicle is parked. Unbuckle the seat
belt to release the child. If the seat belt
can not be unbuckled or is already
unbuckled, release the child by cutting
the seat belt with a suitable tool (such
as a knife or scissors) to release the
seat belt.
Children need adults to help protect them.
They need to be properly restrained.
In addition to the general information in this
manual, child safety information is available from
many other sources, including doctors, teachers,
government traffic safety offices, and community
organizations. Every child is different, so be sure
to learn the best way to transport your child.
There are three basic types of child restraint
.
Rear-facing child restraint
.
Forward-facing child restraint
. Booster seat
The proper restraint depends on the child’s size.
Generally, infants (up to about 1 year and less
than 20 lb (9 kg)) should be placed in rearfacing child restraints. Forward-facing child
restraints are available for children who outgrow
rear-facing child restraints and are at least 1
year old. Booster seats are used to help position
a vehicle lap/shoulder belt on a child who can no
longer use a forward-facing child restraint.
WARNING
Infants and children need special protection. The vehicle’s seat belts may not
fit them properly. The shoulder belt may
come too close to the face or neck. The
lap belt may not fit over their small hip
bones. In an accident, an improperly
fitting seat belt could cause serious or
fatal injury. Always use appropriate
child restraints.
All U.S. states and Canadian provinces or
territories require the use of approved child
Safety — Seats, seat belts and supplemental restraint system 1-13
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(64,1)
restraints for infants and small children.
(
“Child restraints” page 1-15)
A child restraint may be secured in the vehicle
by using either the LATCH (Lower Anchor and
Tethers for CHildren) system or with the vehicle
seat belt. (
“Child restraints” page 1-15)
NISSAN recommends that all pre-teens
and children be restrained in the rear seat.
According to accident statistics, children
are safer when properly restrained in the
rear seat than in the front seat.
This is especially important because your
vehicle has a supplemental restraint system (air bag system) for the front passenger. (
“Supplemental restraint system”
page 1-34)
INFANTS
Infants up to at least one year old should be
placed in a rear-facing child restraint. NISSAN
recommends that infants be placed in child
restraints that comply with Federal Motor
Vehicle Safety Standards or Canadian Motor
Vehicle Safety Standards. You should choose a
child restraint which fits your vehicle and always
follow the manufacturer’s instructions for installation and use.
SMALL CHILDREN
Children that are over 1 year old and weigh at
least 20 lb (9 kg) should remain in a rear-facing
child restraint as long as possible up to the
height or weight limit of the child restraint.
Children who outgrow the height or weight limit
of the rear-facing child restraint and are at least
1 year old should be secured in a forward-facing
child restraint with a harness. Refer to the
manufacturer’s instructions for minimum and
maximum weight and height recommendations.
NISSAN recommends that small children be
placed in child restraints that comply with
Federal Motor Vehicle Safety Standards or
Canadian Motor Vehicle Safety Standards. You
should choose a child restraint that fits your
vehicle and always follow the manufacturer’s
instructions for installation and use.
LARGER CHILDREN
Children should remain in a forward-facing child
restraint with a harness until they reach the
maximum height or weight limit allowed by the
child restraint manufacturer.
Once a child outgrows the height or weight limit
of the harness-equipped forward-facing child
restraint, NISSAN recommends that the child be
placed in a commercially available booster seat
to obtain proper seat belt fit. For a seat belt to fit
properly, the booster seat should raise the child
so that the shoulder belt is properly positioned
across the chest and the top, middle portion of
the shoulder. The shoulder belt should not cross
the neck or face and should not fall off the
shoulder. The lap belt should lie snugly across
the lower hips or upper thighs, not the abdomen.
A booster seat can only be used in seating
positions that have a three-point type seat belt.
The booster seat should fit the vehicle seat and
have a label certifying that it complies with
Federal Motor Vehicle Safety Standards or
Canadian Motor Vehicle Safety Standards.
Once the child has grown so the shoulder belt
is no longer on or near the face and neck, and
the lap belt can be positioned properly across
the lower hips or upper thighs, use the seat belt
without the booster seat.
WARNING
Never let a child stand or kneel on any
seat and do not allow a child in the
cargo areas while the vehicle is moving.
The child could be seriously injured or
killed in an accident or sudden stop.
1-14 Safety — Seats, seat belts and supplemental restraint system
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(65,1)
CHILD RESTRAINTS
PRECAUTIONS ON CHILD RESTRAINTS
WARNING
.
Failure to follow the warnings and
instructions for proper use and installation of child restraints could
result in serious injury or death of a
child or other passengers in a
sudden stop or collision:
— The child restraint must be used
and installed properly. Always
follow all of the child restraint
manufacturer’s instructions for
installation and use.
— Infants and children should
never be held on anyone’s lap.
Even the strongest adult cannot
resist the forces of a collision.
— Do not put a seat belt around
both a child and another passenger.
— NISSAN recommends that all
child restraints be installed in
the rear seat. Studies show that
children are safer when properly
restrained in the rear seat than
in the front seat. If you must
install a forward-facing child
restraint in the front seat.
(
“Forward-facing child restraint installation using the
seat belts” page 1-26)
— Even with the NISSAN Advanced
Air Bag System, never install a
rear-facing child restraint in the
front seat. An inflating air bag
could seriously injure or kill a
child. A rear-facing child restraint must only be used in the
rear seat.
— Be sure to purchase a child
restraint that will fit the child
and vehicle. Some child restraints may not fit properly in
your vehicle.
— Child restraint anchor points are
designed to withstand loads
from child restraints that are
properly fitted.
— Never use the anchor points for
adult seat belts or harnesses.
— A child restraint with a top tether
strap should not be used in the
Safety — Seats, seat belts and supplemental restraint system 1-15
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(66,1)
front passenger seat.
— Keep seatbacks as upright as
possible after fitting the child
restraint.
— Infants and children should always be placed in an appropriate child restraint while in the
vehicle.
.
When the child restraint is not in
use, keep it secured with the LATCH
system or a seat belt. In a sudden
stop or collision, loose objects can
injure occupants or damage the
vehicle.
CAUTION
connected to these anchors. (See
“Lower
Anchors and Tethers for CHildren System
(LATCH)” page 1-17.)
If you do not have a LATCH compatible child
restraint, the vehicle seat belts can be used.
Several manufacturers offer child restraints for
infants and small children of various sizes. When
selecting any child restraint, keep the following
points in mind:
.
Choose only a restraint with a label certifying
that it complies with Federal Motor Vehicle
Safety Standard 213 or Canadian Motor
Vehicle Safety Standard 213.
.
Check the child restraint in your vehicle to
be sure it is compatible with the vehicle’s
seat and seat belt system.
.
If the child restraint is compatible with your
vehicle, place your child in the child restraint
and check the various adjustments to be
sure the child restraint is compatible with
your child. Choose a child restraint that is
designed for your child’s height and weight.
Always follow all recommended procedures.
.
If the combined weight of the child and child
restraint is less than 65 lbs (29.5 kg), you
may use either the LATCH anchors or the
seat belt to install the child restraint (not
both at the same time).
A child restraint in a closed vehicle can
become very hot. Check the seating
surface and buckles before placing a
child in the child restraint.
This vehicle is equipped with a universal child
restraint anchor system, referred to as the
LATCH (Lower Anchors and Tethers for CHildren) system. Some child restraints include rigid
or webbing-mounted attachments that can be
.
If the combined weight of the child and child
restraint is greater than 65 lbs (29.5 kg), use
the vehicle’s seat belt (not the lower
anchors) to install the child restraint.
.
Be sure to follow the child restraint manufacturer’s instructions for installation.
All U.S. states and Canadian provinces or
territories require that infants and small
children be restrained in an approved child
restraint at all times while the vehicle is
being operated. Canadian law requires the
top tether strap on forward-facing child
restraints be secured to the designated
anchor point on the vehicle.
1-16 Safety — Seats, seat belts and supplemental restraint system
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(67,1)
install the child restraint. Be sure to follow the
child restraint manufacturer’s instructions for
installation.
LATCH lower anchor
WARNING
Failure to follow the warnings and
instructions for proper use and installation of child restraints could result in
serious injury or death of a child or
other passengers in a sudden stop or
collision:
LATCH label location
.
Attach LATCH system compatible
child restraints only at the locations
shown in the illustration.
.
Inspect the lower anchors by inserting your fingers into the lower
anchor area. Feel to make sure
there are no obstructions over the
anchors such as seat belt webbing
or seat cushion material. The child
restraint will not be secured properly if the lower anchors are obstructed.
Lower Anchors and Tethers for
CHildren System (LATCH)
Your vehicle is equipped with special anchor
points that are used with the LATCH (Lower
Anchors and Tethers for CHildren) system
compatible child restraints. This system may
also be referred to as the ISOFIX or ISOFIX
compatible system. With this system, you do not
have to use a vehicle seat belt to secure the
child restraint unless the combined weight of the
child and child restraint exceeds 65 lbs (29.5
kg). If the combined weight of the child and child
restraint is greater than 65 lbs (29.5 kg), use the
vehicle’s seat belt (not the lower anchors) to
straints. Under no circumstances are
they to be used to attach adult seat
belts, or other items or equipment to
the vehicle. Doing so could damage the
child restraint anchorages. The child
restraint will not be properly installed
using the damaged anchorage, and a
child could be seriously injured or killed
in a collision.
Child restraint anchorages are designed to withstand only those loads
imposed by correctly fitted child reSafety — Seats, seat belts and supplemental restraint system 1-17
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(68,1)
LATCH lower anchor location
LATCH lower anchor location
The LATCH anchors are located at the rear of
the seat cushion near the seatback. A label is
attached to the seatback to help you locate the
LATCH anchors.
WARNING
The GT-R has seats and seat belts for
four occupants, two in the front seats
and two in the rear seats. Never use the
rear console as a seating position or for
a child restraint.
LATCH webbing-mounted attachment
Installing child restraint LATCH
lower anchor attachments
LATCH rigid-mounted attachment
When installing a child restraint, carefully read
and follow the instructions in this manual and
those supplied with the child restraint.
LATCH compatible child restraints include two
rigid or webbing-mounted attachments that can
be connected to two anchors located at certain
seating positions in your vehicle. With this
system, you do not have to use a vehicle seat
belt to secure the child restraint. Check your
child restraint for a label stating that it is
compatible with LATCH. This information may
also be in the instructions provided by the child
restraint manufacturer.
1-18 Safety — Seats, seat belts and supplemental restraint system
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(69,1)
restraint will not be properly installed
using the damaged anchorage, and a
child could be seriously injured or killed
in a collision.
REAR-FACING CHILD RESTRAINT
INSTALLATION USING LATCH
Top tether anchor point locations
Anchor points are located on the rear parcel
shelf.
WARNING
Child restraint anchorages are designed to withstand only those loads
imposed by correctly fitted child restraints. Under no circumstances are
they to be used to attach adult seat
belts, or other items or equipment to
the vehicle. Doing so could damage the
child restraint anchorages. The child
Refer to all Warnings and Cautions in the “Child
safety” and “Child restraints” sections before
installing a child restraint.
Do not use the lower anchors if the combined
weight of the child and the child restraint
exceeds 65 lbs (29.5 kg). If the combined
weight of the child and the child restraint is
greater than 65 lbs (29.5 kg), use the vehicle’s
seat belt (not the lower anchors) to install the
child restraint. Be sure to follow the child
restraint manufacturer’s instructions for installation.
Follow these steps to install a rear-facing child
restraint using the LATCH system:
1. Position the child restraint on the seat.
Always follow the child restraint manufacturer’s instructions.
Rear-facing web-mounted — step 2
2. Secure the child restraint anchor attachments to the LATCH lower anchors. Check
to make sure the LATCH attachment is
properly attached to the lower anchors.
Safety — Seats, seat belts and supplemental restraint system 1-19
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(70,1)
Rear-facing rigid-mounted — step 2
Rear-facing — step 3
Rear-facing — step 4
3. For child restraints that are equipped with
webbing-mounted attachments, remove any
additional slack from the anchor attachments. Press downward and rearward firmly
in the center of the child restraint with your
hand to compress the vehicle seat cushion
and seatback while tightening the webbing
of the anchor attachments.
4. After attaching the child restraint, test it
before you place the child in it. Push it from
side to side while holding the child restraint
near the LATCH attachment path. The child
restraint should not move more than 1 inch
(25 mm), from side to side. Try to tug it
forward and check to see if the LATCH
attachment holds the restraint in place. If the
restraint is not secure, tighten the LATCH
attachment as necessary, or put the restraint
in another seat and test it again. You may
need to try a different child restraint or try
installing by using the vehicle seat belt (if
applicable). Not all child restraints fit in all
types of vehicles.
1-20 Safety — Seats, seat belts and supplemental restraint system
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(71,1)
5. Check to make sure the child restraint is
properly secured prior to each use. If the
child restraint is loose, repeat steps 1
through 4.
change the operation of the front
passenger air bag. See “Front passenger air bag and status light” later in this
section.
REAR-FACING CHILD RESTRAINT
INSTALLATION USING THE SEAT
BELTS
WARNING
The three-point seat belt with Automatic Locking Retractor (ALR) must be
used when installing a child restraint.
Failure to use the ALR mode will result
in the child restraint not being properly
secured. The restraint could tip over or
be loose and cause injury to a child in a
sudden stop or collision. Also, it can
Safety — Seats, seat belts and supplemental restraint system 1-21
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(72,1)
seats:
1. Child restraints for infants must be
used in the rear-facing direction and
therefore must not be used in the front
seat. Position the child restraint on the seat.
Always follow the restraint manufacturer’s
instructions.
Rear-facing — step 1
Rear-facing — step 2
Refer to all Warnings and Cautions in “Child
safety” and “Child restraints” before installing a
child restraint.
Do not use the lower anchors if the combined
weight of the child and the child restraint
exceeds 65 lbs (29.5 kg). If the combined
weight of the child and the child restraint is
greater than 65 lbs (29.5 kg), use the vehicle’s
seat belt (not the lower anchors) to install the
child restraint. Be sure to follow the child
restraint manufacturer’s instructions for installation.
Follow these steps to install a rear-facing child
restraint using the vehicle seat belts in the rear
2. Route the seat belt tongue through the child
restraint and insert it into the buckle until you
hear and feel the latch engage. Be sure to
follow the child restraint manufacturer’s
instructions for belt routing.
1-22 Safety — Seats, seat belts and supplemental restraint system
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(73,1)
Rear-facing — step 3
Rear-facing — step 4
Rear-facing — step 5
3. Pull the shoulder belt until the belt is fully
extended. At this time, the seat belt retractor
is in the Automatic Locking Retractor (ALR)
mode (child restraint mode). It reverts to the
Emergency Locking Retractor (ELR) mode
when the seat belt is fully retracted.
4. Allow the seat belt to retract. Pull up on the
shoulder belt to remove any slack in the belt.
5. Remove any additional slack from the seat
belt; press downward and rearward firmly in
the center of the child restraint to compress
the vehicle seat cushion and seatback while
pulling up on the seat belt.
Safety — Seats, seat belts and supplemental restraint system 1-23
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(74,1)
seat belt is not locked, repeat steps 1
through 6.
After the child restraint is removed and the seat
belt fully retracted, the ALR mode (child restraint
mode) is canceled.
FORWARD-FACING CHILD RESTRAINT INSTALLATION USING
LATCH
Rear-facing — step 6
6. After attaching the child restraint, test it
before you place the child in it. Push it from
side to side while holding the child restraint
near the seat belt path. The child restraint
should not move more than 1 inch (25 mm),
from side to side. Try to tug it forward and
check to see if the belt holds the restraint in
place. If the restraint is not secure, tighten
the seat belt as necessary, or put the
restraint in another seat and test it again.
You may need to try a different child
restraint. Not all child restraints fit in all
types of vehicles.
7. Check to make sure that the child restraint is
properly secured prior to each use. If the
Refer to all Warnings and Cautions in the “Child
safety” and “Child restraints” sections before
installing a child restraint.
Do not use the lower anchors if the combined
weight of the child and the child restraint
exceeds 65 lbs (29.5 kg). If the combined
weight of the child and the child restraint is
greater than 65 lbs (29.5 kg), use the vehicle’s
seat belt (not the lower anchors) to install the
child restraint. Be sure to follow the child
restraint manufacturer’s instructions for installation.
Follow these steps to install a forward-facing
child restraint using the LATCH system:
1. Position the child restraint on the seat.
Always follow the child restraint manufacturer’s instructions.
Forward-facing web-mounted — step 2
2. Secure the child restraint anchor attachments to the LATCH lower anchors. Check
to make sure the LATCH attachment is
properly attached to the lower anchors.
If the child restraint is equipped with a top
tether strap, route the top tether strap and
secure the tether strap to the tether anchor
point. See
“Installing top tether strap”
page 1-26. Do not install child restraints that
require the use of a top tether strap in
seating positions that do not have a top
tether anchor.
1-24 Safety — Seats, seat belts and supplemental restraint system
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(75,1)
Forward-facing rigid-mounted — step 2
Forward-facing — step 4
Forward-facing — step 6
3. The back of the child restraint should be
secured against the vehicle seatback.
If the seating position is interfering with the
proper child restraint fit, try another seating
position or a different child restraint.
4. For child restraints that are equipped with
webbing-mounted attachments, remove any
additional slack from the anchor attachments. Press downward and rearward firmly
in the center of the child restraint with your
knee to compress the vehicle seat cushion
and seatback while tightening the webbing
of the anchor attachments.
5. Tighten the tether strap according to the
manufacturer’s instructions to remove any
slack.
6. After attaching the child restraint, test it
before you place the child in it. Push it from
side to side while holding the child restraint
near the LATCH attachment path. The child
restraint should not move more than 1 inch
(25 mm), from side to side. Try to tug it
forward and check to see if the LATCH
attachment holds the restraint in place. If the
restraint is not secure, tighten the LATCH
attachment as necessary, or put the restraint
in another seat and test it again. You may
need to try a different child restraint. Not all
child restraints fit in all types of vehicles.
7. Check to make sure the child restraint is
properly secured prior to each use. If the
Safety — Seats, seat belts and supplemental restraint system 1-25
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(76,1)
4. Refer to the appropriate child restraint
installation procedure steps earlier in this
section before tightening the tether strap.
If you have any questions when installing a
top tether strap, consult a GT-R certified
NISSAN dealer for details.
child restraint is loose, repeat steps 1
through 6.
FORWARD-FACING CHILD RESTRAINT INSTALLATION USING THE
SEAT BELTS
WARNING
Installing top tether strap
The child restraint top tether strap must be used
when installing the child restraint with the
LATCH lower anchor attachments.
First, secure the child restraint with the LATCH
lower anchors (rear outboard seat positions
only).
1. Flip up the anchor cover from the anchor
point which is located directly behind the
child restraint.
2. Position the top tether strap over the top of
the seatback.
3. Secure the tether strap to the tether anchor
point on the rear parcel shelf.
The three-point seat belt with Automatic Locking Retractor (ALR) must be
used when installing a child restraint.
Failure to use the ALR mode will result
in the child restraint not being properly
secured. The restraint could tip over or
be loose and cause injury to a child in a
sudden stop or collision. Also, it can
change the operation of the front
passenger air bag. See “Front passenger air bag and status light” later in this
section.
1-26 Safety — Seats, seat belts and supplemental restraint system
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(77,1)
Forward-facing (front passenger seat) — step 1
Refer to all Warnings and Cautions in the “Child
safety” and “Child restraints” sections before
installing a child restraint.
Do not use the lower anchors if the combined
weight of the child and the child restraint
exceeds 65 lbs (29.5 kg). If the combined
weight of the child and the child restraint is
greater than 65 lbs (29.5 kg), use the vehicle’s
seat belt (not the lower anchors) to install the
child restraint. Be sure to follow the child
restraint manufacturer’s instructions for installation.
Follow these steps to install a forward-facing
child restraint using the vehicle seat belt in the
rear seats or in the front passenger seat:
1. If you must install a child restraint in
the front seat, it should be placed in a
forward-facing direction only. Move the
seat to the rearmost position. Child
restraints for infants must be used in
the rear-facing direction and, therefore,
must not be used in the front seat.
2. Position the child restraint on the seat.
Always follow the child restraint manufacturer’s instructions.
The back of the child restraint should be
secured against the vehicle seatback.
If the seating position is interfering with the
proper child restraint fit, try another seating
position or a different child restraint.
Forward-facing — step 3
3. Route the seat belt tongue through the child
restraint and insert it into the buckle until you
hear and feel the latch engage. Be sure to
follow the child restraint manufacturer’s
instructions for belt routing.
If the child restraint is equipped with a top
tether strap, route the top tether strap and
secure the tether strap to the tether anchor
point. (
“Installing top tether strap”
page 1-30) Do not install child restraints
that require the use of a top tether strap in
seating positions that do not have a top
tether anchor.
Safety — Seats, seat belts and supplemental restraint system 1-27
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(78,1)
Forward-facing — step 4
Forward-facing — step 5
Forward-facing — step 6
4. Pull the shoulder belt until the belt is fully
extended. At this time, the seat belt retractor
is in the Automatic Locking Retractor (ALR)
mode (child restraint mode). It reverts to
Emergency Locking Retractor (ELR) mode
when the seat belt is fully retracted.
5. Allow the seat belt to retract. Pull up on the
shoulder belt to remove any slack in the belt.
6. Remove any additional slack from the seat
belt; press downward and rearward firmly in
the center of the child restraint with your
knee to compress the vehicle seat cushion
and seatback while pulling up on the seat
belt.
7. Tighten the tether strap according to the
manufacturer’s instructions to remove any
slack.
1-28 Safety — Seats, seat belts and supplemental restraint system
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(79,1)
seat belt is not locked, repeat steps 2
through 8.
Forward-facing — step 8
Forward-facing — step 10
8. After attaching the child restraint, test it
before you place the child in it. Push it from
side to side while holding the child restraint
near the seat belt path. The child restraint
should not move more than 1 inch (25 mm),
from side to side. Try to tug it forward and
check to see if the belt holds the restraint in
place. If the restraint is not secure, tighten
the seat belt as necessary, or put the
restraint in another seat and test it again.
You may need to try a different child
restraint. Not all child restraints fit in all
types of vehicles.
9. Check to make sure the child restraint is
properly secured prior to each use. If the
10. If the child restraint is installed in the front
passenger seat, place the ignition switch in
the ON position. The front passenger air bag
status light
should illuminate. If this light
is not illuminated, see “Front passenger air
bag and status light” in this section. Move
the child restraint to another seating
position. Have the system checked by a
GT-R certified NISSAN dealer.
After the child restraint is removed and the seat
belt is fully retracted, the ALR mode (child
restraint mode) is canceled.
Safety — Seats, seat belts and supplemental restraint system 1-29
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(80,1)
section before tightening the tether strap.
If you have any questions when installing a
top tether strap, consult a GT-R certified
NISSAN dealer for details.
BOOSTER SEATS
Precautions on booster seats
WARNING
If a booster seat and seat belt are not
used properly, the risk of a child being
injured in a sudden stop or collision
greatly increases:
Installing top tether strap
The child restraint top tether strap must be used
when installing the child restraint with the seat
belts.
First, secure the child restraint with the seat belt.
1. Flip up the anchor cover from the anchor
point which is located directly behind the
child restraint.
2. Position the top tether strap over the top of
the seatback.
3. Secure the tether strap to the tether anchor
point on the rear parcel shelf.
4. Refer to the appropriate child restraint
installation procedure steps earlier in this
.
Make sure the shoulder portion of
the belt is away from the child’s face
and neck and the lap portion of the
belt does not cross the stomach.
.
Make sure the shoulder belt is not
behind the child or under the child’s
arm.
.
A booster seat must only be installed in a seating position that has
a lap/shoulder belt.
Booster seats of various sizes are offered by
several manufacturers. When selecting any
booster seat, keep the following points in mind:
.
Choose only a booster seat with a label
certifying that it complies with Federal Motor
Vehicle Safety Standard 213 or Canadian
Motor Vehicle Safety Standard 213.
.
Check the booster seat in your vehicle to be
sure it is compatible with the vehicle’s seat
and seat belt system.
1-30 Safety — Seats, seat belts and supplemental restraint system
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(81,1)
Booster seat installation
CAUTION
Do not use the lap/shoulder belt Automatic Locking Retractor (ALR) mode
when using a booster seat with the
seat belts.
.
Make sure the child’s head will be properly
supported by the booster seat or vehicle
seat. The seatback must be at or above the
center of the child’s ears. For example, if a
1 is chosen, the
low back booster seat *
vehicle seatback must be at or above the
center of the child’s ears. If the seatback is
lower than the center of the child’s ears, a
2 should be used.
high back booster seat *
.
If the booster seat is compatible with your
vehicle, place your child in the booster seat
and check the various adjustments to be
sure the booster seat is compatible with
your child. Always follow all recommended
procedures.
All U.S. states and Canadian provinces or
territories require that infants and small
children be restrained in an approved child
restraint at all times while the vehicle is
being operated.
The instructions in this section apply to booster
seat installation in the rear seats or the front
passenger seat.
Refer to all Warnings and Cautions in the “Child
safety”, “Child restraints” and “Booster seats”
sections earlier in this section before installing a
child restraint.
Follow these steps to install a booster seat in the
rear seat or in the front passenger seat:
Safety — Seats, seat belts and supplemental restraint system 1-31
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(82,1)
manufacturer’s instructions for adjusting the
belt routing.
1. If you must install a booster seat in the
front seat, move the seat to the rearmost position.
2. Position the booster seat on the seat. Only
place it in a forward-facing direction. Always
follow the booster seat manufacturer’s
instructions.
Outboard position
3. The booster seat should be positioned on
the vehicle seat so that it is stable. If the
seating position is interfering with the proper
booster seat fit, try another seating position
or a different booster seat.
4. Position the lap portion of the seat belt low
and snug on the child’s hips. Be sure to
follow the booster seat manufacturer’s
instructions for adjusting the belt routing.
5. Pull the shoulder belt portion of the seat belt
toward the retractor to take up extra slack.
Be sure the shoulder belt is positioned
across the top, middle portion of the child’s
shoulder. Be sure to follow the booster seat
1-32 Safety — Seats, seat belts and supplemental restraint system
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(83,1)
Front seat
6. Follow the warnings, cautions and instructions for properly fastening a seat belt.
(
“Three-point type seat belt with retractor” page 1-9)
7. If the booster seat is installed in the front
passenger seat, push the ignition switch to
the ON position. The front passenger air bag
status light
may or may not illuminate
depending on the size of the child and the
type of booster seat used. (
“Front
passenger air bag and status light” page
1-41)
Safety — Seats, seat belts and supplemental restraint system 1-33
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(84,1)
SUPPLEMENTAL RESTRAINT
SYSTEM
PRECAUTIONS ON SUPPLEMENTAL
RESTRAINT SYSTEM
This Supplemental Restraint System (SRS)
section contains important information concerning the following systems:
.
Driver and passenger supplemental frontimpact air bag (NISSAN Advanced Air Bag
System)
.
Front seat-mounted side-impact supplemental air bag
.
Roof-mounted curtain side-impact supplemental air bag
. Seat belt pretensioner
Supplemental front-impact air bag system:
The NISSAN Advanced Air Bag System can
help cushion the impact force to the head and
chest of the driver and front passenger in certain
frontal collisions.
Front seat-mounted side-impact supplemental air bag system: This system can help
cushion the impact force to the chest area of the
driver and front passenger in certain side impact
collisions. The side air bags are designed to
inflate on the side where the vehicle is impacted.
Roof-mounted curtain side-impact supplemental air bag system: This system can help
cushion the impact force to the head of
occupants in the front seating positions in
certain side impact collisions. The curtain air
bags are designed to inflate on the side where
the vehicle is impacted.
These supplemental restraint systems are designed to supplement the crash protection
provided by the driver and passenger seat belts
and are not a substitute for them. Seat belts
should always be correctly worn and the
occupant seated a suitable distance away from
the steering wheel, instrument panel and door
finishers. (
“Seat belts” page 1-6)
The supplemental air bags operate only
when the ignition switch is in the ON
position.
After pushing the ignition switch to the ON
position, the supplemental air bag warning
light illuminates. The supplemental air bag
warning light will turn off after about 7
seconds if the systems are operational.
1-34 Safety — Seats, seat belts and supplemental restraint system
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(85,1)
WARNING
.
The front air bags ordinarily will not
inflate in the event of a side impact,
rear impact, rollover, or lower severity frontal collision. Always wear
your seat belts to help reduce the
risk or severity of injury in various
kinds of accidents.
.
The front passenger air bag will not
inflate if the passenger air bag
status light is lit or if the front
passenger seat is unoccupied.
(
“Front passenger air bag and
status light” page 1-41)
.
The seat belts and the front air bags
are most effective when you are
sitting well back and upright in the
seat. The front air bags inflate with
great force. Even with the NISSAN
Advanced Air Bag System, if you are
unrestrained, leaning forward, sitting sideways or out of position in
any way, you are at greater risk of
injury or death in a crash. You may
also receive serious or fatal injuries
from the front air bag if you are up
against it when it inflates. Always sit
Sit upright and well back.
Sit upright and well back.
Safety — Seats, seat belts and supplemental restraint system 1-35
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(86,1)
back against the seatback and as
far-away as practical from the steering wheel or instrument panel. Always use the seat belts.
.
The driver and front passenger seat
belt buckles are equipped with
sensors that detect if the seat belts
are fastened. The Advanced Air Bag
System monitors the severity of a
collision and seat belt usage then
inflates the air bags as needed.
Failure to properly wear seat belts
can increase the risk or severity of
injury in an accident.
.
The front passenger seat is
equipped with an occupant classification sensor (pattern sensor) that
turns the front passenger air bag
OFF under some conditions. This
sensor is only used in this seat.
Failure to be properly seated and
wearing the seat belt can increase
the risk or severity of injury in an
accident. (
“Front passenger air
bag and status light” page 1-41)
.
Keep hands on the outside of the
steering wheel. Placing them inside
the steering wheel rim could in-
crease the risk of hand injury if the
supplemental front air bag inflates.
1-36 Safety — Seats, seat belts and supplemental restraint system
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(87,1)
WARNING
.
Never let children ride unrestrained
or extend their hands or face out of
the window. Do not attempt to hold
them in your lap or arms. Some
examples of dangerous riding positions are shown in the illustrations.
.
Children may be severely injured or
killed when the front air bags, side
air bags or curtain air bags inflate if
they are not properly restrained.
Pre-teens and children should be
properly restrained in the rear seat,
if possible.
.
Even with the NISSAN Advanced Air
Bag System, never install a rearfacing child restraint in the front
seat. An inflating supplemental
front air bag could seriously injure
or kill your child. (
“Child restraints” page 1-15)
Safety — Seats, seat belts and supplemental restraint system 1-37
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(88,1)
WARNING
Front seat-mounted side-impact supplemental air bag and roof-mounted
curtain side-impact supplemental air
bag :
Do not lean against doors or windows.
.
The side air bags and curtain air
bags ordinarily will not inflate in the
event of a frontal impact, rear impact, rollover or lower severity side
collision. Always wear your seat
belts to help reduce the risk or
severity of injury in various kinds
of accidents.
.
The seat belts, side air bags and
curtain air bags are most effective
when you are sitting well back and
upright in the seat. The side air bags
and curtain air bags inflate with
great force. Do not allow anyone to
place their hand, leg or face near the
side air bag on the side of the
seatback of the front seat or near
the side roof rails. Do not allow
anyone sitting in the front seat to
extend their hand out of the window
or lean against the door. Some
examples of dangerous riding posi-
Do not lean against doors or windows.
1-38 Safety — Seats, seat belts and supplemental restraint system
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(89,1)
tions are shown in the previous
illustrations.
.
When sitting in the rear seat, do not
hold onto the seatback of the front
seat. If the supplemental side air
bag inflates, you may be seriously
injured. Be especially careful with
children, who should always be
properly restrained. Some examples
of dangerous riding positions are
shown in the illustrations.
.
Do not use seat covers on the front
seatbacks. They may interfere with
side air bag inflation.
Safety — Seats, seat belts and supplemental restraint system 1-39
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(90,1)
10.
11.
Seat belt pretensioners
Air bag Control Unit (ACU)
NISSAN ADVANCED AIR BAG SYSTEM (front seats)
1.
2.
3.
4.
Crash zone sensor
Supplemental front-impact air bag modules
(NISSAN Advanced Air Bag System)
Front seat-mounted side-impact supplemental
air bags
Roof-mounted curtain side-impact supplemental
air bags
5.
6.
7.
8.
9.
Roof-mounted curtain side-impact supplemental
air bag inflators
Door satellite sensors
Occupant classification sensor (pattern sensor)
Occupant classification system control unit
Satellite sensors
This vehicle is equipped with the NISSAN
Advanced Air Bag System for the driver and
front passenger seats. This system is designed
to meet certification requirements under U.S.
regulations. It is also permitted in Canada. All of
the information, cautions and warnings in
this manual apply and must be followed.
The driver supplemental front-impact air bag is
located in the center of the steering wheel. The
front passenger supplemental front-impact air
bag is mounted in the instrument panel above
the glove box. The front air bags are designed to
inflate in higher severity frontal collisions,
although they may inflate if the forces in another
type of collision are similar to those of a higher
severity frontal impact. They may not inflate in
certain frontal collisions. Vehicle damage (or lack
of it) is not always an indication of proper front
air bag operation.
The NISSAN Advanced Air Bag System has
dual stage air bag inflators. The system monitors
information from the Air bag Control Unit (ACU),
seat belt buckle sensors and the occupant
classification sensor (pattern sensor). Inflator
operation is based on the severity of a collision
1-40 Safety — Seats, seat belts and supplemental restraint system
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(91,1)
and seat belt usage for the driver. For the front
passenger, the occupant classification sensor is
also monitored. Based on information from the
sensors, only one front air bag may inflate in a
crash, depending on the crash severity and
whether the front occupants are belted or
unbelted. Additionally, the front passenger air
bag may be automatically turned OFF under
some conditions, depending on the information
provided by the occupant classification sensor.
If the front passenger air bag is OFF, the
passenger air bag status light will be illuminated
(if the seat is unoccupied, the light will not be
illuminated, but the air bag will be off). One front
air bag inflating does not indicate improper
performance of the system. (
“Front passenger air bag and status light” page 1-41)
If you have any questions about your air bag
system, contact NISSAN or a GT-R certified
NISSAN dealer. If you are considering modification of your vehicle due to a disability, you may
also contact NISSAN. Contact information is
contained in the front of this Owner’s Manual.
When a front air bag inflates, a fairly loud noise
may be heard, followed by release of smoke.
This smoke is not harmful and does not indicate
a fire. Care should be taken not to inhale it, as it
may cause irritation and choking. Those with a
history of a breathing condition should get fresh
air promptly.
Front air bags, along with the use of seat belts,
help to cushion the impact force on the head
and chest of the front occupants. They can help
save lives and reduce serious injuries. However,
an inflating front air bag may cause facial
abrasions or other injuries. Front air bags do
not provide restraint to the lower body.
Even with NISSAN advanced air bags, seat
belts should be correctly worn and the driver
and passenger seated upright as far as practical
away from the steering wheel or instrument
panel. The front air bags inflate quickly in order
to help protect the front occupants. Because of
this, the force of the front air bag inflating can
increase the risk of injury if the occupant is too
close to, or is against, the air bag module during
inflation.
The front air bags deflate quickly after a collision.
The front air bags operate only when the
ignition switch is in the ON position.
After pushing the ignition switch to the ON
position, the supplemental air bag warning
light illuminates. The supplemental air bag
warning light will turn off after about 7
seconds if the system is operational.
Front passenger air bag status light
Front passenger air bag and status
light
WARNING
The front passenger air bag is designed
to automatically turn OFF under some
conditions. Read this section carefully
to learn how it operates. Proper use of
the seat, seat belt and child restraints is
necessary for most effective protection.
Failure to follow all instructions in this
manual concerning the use of seats,
seat belts and child restraints can
Safety — Seats, seat belts and supplemental restraint system 1-41
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(92,1)
increase the risk or severity of injury in
an accident.
Status light:
The front passenger air bag status light
is
located on the center instrument panel. After the
ignition switch is placed in the ON position, the
front passenger air bag status light on the
instrument panel illuminates for about 7 seconds
and then turns off or illuminates depending on
the front passenger seat occupied status. The
light operates as follows:
.
Unoccupied passenger seat: The
light
is OFF and the front passenger air bag is
OFF and will not inflate in a crash.
.
Passenger seat occupied by a small adult,
child or child restraint as outlined in this
section: The
light illuminates to indicate
that the front passenger air bag is OFF and
will not inflate in a crash.
.
Occupied passenger seat and the passenger meets the conditions outlined in this
section: The
light is OFF to indicate that
the front passenger air bag is operational.
Front passenger air bag:
The front passenger air bag is designed to
automatically turn OFF when the vehicle is
operated under some conditions as described
below as permitted by U.S. regulations. If the
front passenger air bag is OFF, it will not inflate
in a crash. The driver air bag and other air bags
in your vehicle are not part of this system.
The purpose of the regulation is to help reduce
the risk of injury or death from an inflating air bag
to certain front passenger seat occupants, such
as children, by requiring the air bag to be
automatically turned OFF.
The occupant classification sensor (pattern
sensor) is in the front passenger seat cushion
and is designed to detect an occupant and
objects on the seat. For example, if a child is in
the front passenger seat, the Advanced Air Bag
System is designed to turn the passenger air
bag OFF in accordance with the regulations.
Also, if a child restraint of the type specified in
the regulations is on the seat, the occupant
classification sensor can detect it and cause the
air bag to turn OFF.
Front passenger seat adult occupants who are
properly seated and using the seat belt as
outlined in this manual should not cause the
passenger air bag to be automatically turned
OFF. For small adults it may be turned OFF,
however, if the occupant does not sit in the seat
properly (for example, by not sitting upright, by
sitting on an edge of the seat, or by otherwise
being out of position), this could cause the
sensor to turn the air bag OFF. Always be sure
to be seated and wearing the seat belt properly
for the most effective protection by the seat belt
and supplemental air bag.
NISSAN recommends that pre-teens and children be properly restrained in a rear seat.
NISSAN also recommends that appropriate
child restraints and booster seats be properly
installed in a rear seat. If this is not possible, the
occupant classification sensor is designed to
operate as described above to turn the front
passenger air bag OFF for specified child
restraints. Failing to properly secure child
restraints and to use the Automatic Locking
Retractor (ALR) mode (child restraint mode)
may allow the restraint to tip or move in an
accident or sudden stop. This can also result in
the passenger air bag inflating in a crash instead
of being OFF. (
“Child restraints” page 115)
If the front passenger seat is not occupied, the
passenger air bag is designed not to inflate in a
crash. However, heavy objects placed on the
seat could result in air bag inflation, because of
the object being detected by the occupant
1-42 Safety — Seats, seat belts and supplemental restraint system
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(93,1)
classification sensor. Other conditions could
also result in air bag inflation, such as if a child is
standing on the seat, or if two children are on the
seat, contrary to the instructions in this manual.
Always be sure that you and all vehicle
occupants are seated and restrained properly.
Using the passenger air bag status light, you can
monitor when the front passenger air bag is
automatically turned OFF with the seat occupied. The light will not illuminate when the front
passenger seat is unoccupied.
If an adult occupant is in the seat but the
passenger air bag status light is illuminated
(indicating that the air bag is OFF), it could be
that the person is a small adult, or is not sitting
on the seat properly.
If a child restraint must be used in the front seat,
the passenger air bag status light may or may
not be illuminated, depending on the size of the
child and the type of child restraint being used. If
the passenger air bag status light is not
illuminated (indicating that the air bag might
inflate in a crash), it could be that the child
restraint or seat belt is not being used properly.
Make sure that the child restraint is installed
properly, the seat belt is used properly and the
occupant is positioned properly. If the passenger air bag status light is still not illuminated,
reposition the occupant or child restraint in a
rear seat.
If the passenger air bag status light will not
illuminate even though you believe that the child
restraint, the seat belts and the occupant are
properly positioned, the system may be sensing
an unoccupied seat (in which case the air bag is
OFF). Your GT-R certified NISSAN dealer can
check that the system is OFF by using a special
tool. However, until you have confirmed with
your dealer that your air bag is working properly,
reposition the occupant or child restraint in a
rear seat.
The NISSAN Advanced Air Bag System and
passenger air bag status light will take a few
seconds to register a change in the passenger
seat status. However, if the seat becomes
unoccupied, the air bag status light will remain
off.
If a malfunction occurs in the front passenger air
bag system, the supplemental air bag warning
light
, located in the meter and gauges area
will blink. Have the system checked by a GT-R
certified NISSAN dealer.
Other supplemental front air bag
precautions
WARNING
.
Do not place any objects on the
steering wheel pad or on the instrument panel. Also, do not place any
objects between any occupant and
the steering wheel or instrument
panel. Such objects may become
dangerous projectiles and cause
injury if the front air bag inflates.
.
Do not place objects with sharp
edges on the seat. Also, do not
place heavy objects on the seat that
will leave permanent impressions in
the seat. Such objects can damage
the seat or occupant classification
sensor (pattern sensor). This can
affect the operation of the air bag
system and result in serious personal injury.
.
Do not use water or acidic cleaners
(hot steam cleaners) on the seat.
This can damage the seat or occupant classification sensor. This can
also affect the operation of the air
Safety — Seats, seat belts and supplemental restraint system 1-43
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(94,1)
bag system and result in serious
personal injury.
.
.
.
.
.
Immediately after inflation, several
front air bag system components
will be hot. Do not touch them; you
may severely burn yourself.
No unauthorized changes should be
made to any components or wiring
of the supplemental air bag system.
This is to prevent accidental inflation of the supplemental air bag or
damage to the supplemental air bag
system.
Do not make unauthorized changes
to your vehicle’s electrical system,
suspension system or front end
structure. This could affect proper
operation of the front air bag system.
Tampering with the supplemental
air bag system may result in serious
personal injury. Tampering includes
changes to the steering wheel and
the instrument panel assembly by
placing material over the steering
wheel pad and above the instrument
panel or by installing additional trim
material around the air bag system.
Modifying or tampering with the
front passenger seat may result in
serious personal injury. For example, do not change the front seats by
placing material on the seat cushion
or by installing additional trim material, such as seat covers, on the
seat that is not specifically designed
to assure proper air bag operation.
Additionally, do not stow any objects under the front passenger seat
or the seat cushion and seatback.
Such objects may interfere with the
proper operation of the occupant
classification sensor.
.
No unauthorized changes should be
made to any components or wiring
of the seat belt system. This may
affect the front air bag system.
Tampering with the seat belt system
may result in serious personal injury.
.
Work on and around the front air
bag system should be done by a
GT-R certified NISSAN dealer. Installation of electrical equipment
should also be done by a GT-R
certified NISSAN dealer. The Supplemental Restraint System (SRS)
wiring harnesses* should not be
modified or disconnected. Unauthorized electrical test equipment
and probing devices should not be
used on the air bag system.
.
A cracked windshield should be
replaced immediately by a qualified
repair facility. A cracked windshield
could affect the function of the
supplemental air bag system.
* The SRS wiring harness connectors are
yellow and orange for easy identification.
When selling your vehicle, we request that you
inform the buyer about the front air bag system
and guide the buyer to the appropriate sections
in this Owner’s Manual.
1-44 Safety — Seats, seat belts and supplemental restraint system
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(95,1)
FRONT SEAT-MOUNTED SIDE-IMPACT SUPPLEMENTAL AIR BAG
AND ROOF-MOUNTED CURTAIN
SIDE-IMPACT SUPPLEMENTAL AIR
BAG SYSTEMS
The front side air bags are located in the outside
of the seatback of the front seats. The curtain air
bags are located in the side roof rails. All of the
information, cautions and warnings in this
manual apply and must be followed. The
side air bags and curtain air bags are designed
to inflate in higher severity side collisions,
although they may inflate if the forces in another
type of collision are similar to those of a higher
severity side impact. They are designed to inflate
on the side where the vehicle is impacted. They
may not inflate in certain side collisions.
Vehicle damage (or lack of it) is not always an
indication of proper side air bag and curtain air
bag operation.
When the side air bags and curtain air bags
inflate, a fairly loud noise may be heard, followed
by release of smoke. This smoke is not harmful
and does not indicate a fire. Care should be
taken not to inhale it, as it may cause irritation
and choking. Those with a history of a breathing
condition should get fresh air promptly.
Front side air bags, along with the use of seat
belts, help to cushion the impact force on the
chest of the front occupants. Curtain air bags
help to cushion the impact force to the head of
occupants in the front seating positions. They
can help save lives and reduce serious injuries.
However, an inflating side air bag and curtain air
bag may cause abrasions or other injuries. Side
air bags and curtain air bags do not provide
restraint to the lower body.
The seat belts should be correctly worn and the
driver and passenger seated upright as far as
practical away from the side air bags. The side
air bags and curtain air bags inflate quickly in
order to help protect occupants. Because of
this, the force of the side air bags and curtain air
bags inflating can increase the risk of injury if the
occupant is too close to, or is against, these air
bag modules during inflation. The side air bags
and curtain air bags will deflate quickly after the
collision is over.
The side air bags and curtain air bags operate
only when the ignition switch is in the ON
position.
After pushing the ignition switch to the ON
position, the supplemental air bag warning
light illuminates. The air bag warning light
will turn off after about 7 seconds if the
systems are operational.
WARNING
.
Do not place any objects near the
seatback of the front seats. Also, do
not place any objects (an umbrella,
bag, etc.) between the front door
finisher and the front seat. Such
objects may become dangerous
projectiles and cause injury if a side
air bag inflates.
.
Right after inflation, several side air
bag and curtain air bag system
components will be hot. Do not
touch them; you may severely burn
yourself.
Safety — Seats, seat belts and supplemental restraint system 1-45
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(96,1)
.
No unauthorized changes should be
made to any components or wiring
of the side air bags and curtain air
bags. This is to prevent damage to
or accidental inflation of the side air
bag and curtain air bag systems.
.
Do not make unauthorized changes
to your vehicle’s electrical system,
suspension system or side panel.
This could affect proper operation
of the side air bag and curtain air
bag systems.
.
.
Tampering with the side air bag
system may result in serious personal injury. For example, do not
change the front seat by placing
material near the seatback or by
installing additional trim material,
such as seat covers, around the side
air bags.
Work around and on the side air bag
and curtain air bag systems should
be done by a GT-R certified NISSAN
dealer. Installation of electrical
equipment should also be done by
a GT-R certified NISSAN dealer. The
SRS wiring harnesses* should not
be modified or disconnected. Un-
authorized electrical test equipment
and probing devices should not be
used on the side air bag and curtain
air bag systems.
* The SRS wiring harness connectors are
yellow and orange for easy identification.
When selling your vehicle, we request that you
inform the buyer about the side air bag and
curtain air bag systems and guide the buyer to
the appropriate sections in this Owner’s Manual.
made to any components or wiring
of the pretensioners. This is to
prevent damage to or accidental
activation of the pretensioners.
Tampering with the pretensioner
system may result in serious personal injury.
.
Work around and on the pretensioners should be done by a GT-R
certified NISSAN dealer. Installation
of electrical equipment should also
be done by a GT-R certified NISSAN
dealer. Unauthorized electrical test
equipment and probing devices
should not be used on the pretensioners.
.
If you need to dispose of a pretensioner or scrap the vehicle, contact a
GT-R certified NISSAN dealer. Incorrect disposal procedures could
cause personal injury.
SEAT BELTS WITH PRETENSIONERS (front seats)
WARNING
.
The pretensioners cannot be reused
after activation. They must be replaced together with the retractor
and buckle as a unit.
.
If the vehicle becomes involved in a
collision but the pretensioner is not
activated, be sure to have the pretensioner system checked and, if
necessary, replaced by a GT-R certified NISSAN dealer.
.
No unauthorized changes should be
The pretensioner system may activate with the
supplemental air bag system in certain types of
collisions. Working with the seat belt retractor, it
helps tighten the seat belt when the vehicle
becomes involved in certain types of collisions,
helping to restrain front seat occupants.
1-46 Safety — Seats, seat belts and supplemental restraint system
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(97,1)
The pretensioner is encased with the seat belt
retractor. These seat belts are used the same
way as conventional seat belts. When a pretensioner activates, smoke is released and a loud
noise may be heard. The smoke is not harmful,
and it does not indicate a fire. Care should be
taken not to inhale it as it may cause irritation
and choking. Those with a history of a breathing
condition should get fresh air promptly.
After pretensioner activation, load limiters allow
the seat belt to release webbing (if necessary) to
reduce forces against the chest.
The supplemental air bag warning light
is
used to indicate malfunctions in the pretensioner
system. (See
“Supplemental air bag warning light” page 1-47 for more details.) If the
operation of the supplemental air bag warning
light indicates there is a malfunction, have the
system checked by a GT-R certified NISSAN
dealer.
When selling your vehicle, we request that you
inform the buyer about the pretensioner system
and guide the buyer to the appropriate sections
in this Owner’s Manual.
SUPPLEMENTAL AIR BAG WARNING LABELS
SUPPLEMENTAL AIR BAG WARNING LIGHT
Warning labels about the supplemental frontimpact air bag are placed in the vehicle as
shown in the illustration.
The supplemental air bag warning light, displaying
in the meter, monitors the circuits for the
air bag systems, pretensioners and all related
wirings.
When the ignition switch is in the ON position,
the supplemental air bag warning light illuminates for about 7 seconds and then turns off.
This means the SRS air bag systems are
operational.
1 SRS air bag
*
The warning labels are located on the surface of
the sun visors.
Safety — Seats, seat belts and supplemental restraint system 1-47
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(98,1)
If any of the following conditions occur, the air
bag and/or pretensioner systems need servicing:
.
The supplemental air bag warning light
remains on after approximately 7 seconds.
.
The supplemental air bag warning light
flashes intermittently.
.
The supplemental air bag warning light does
not come on at all.
Under these conditions, the air bag and/or
pretensioner systems may not operate properly.
They must be checked and repaired. Take your
vehicle to the nearest GT-R certified NISSAN
dealer.
WARNING
If the supplemental air bag warning
light is on, it could mean that the front
air bag, side air bag, curtain air bag
and/or pretensioners will not operate in
an accident. To help avoid injury to
yourself or others, have your vehicle
checked by a dealer as soon as possible.
REPAIR AND REPLACEMENT PROCEDURE
The front air bags, side air bags, curtain air bags
and pretensioners are designed to activate on a
one-time-only basis. As a reminder, unless it is
damaged, the supplemental air bag warning light
will remain illuminated after inflation has occurred. Repair and replacement of these systems should be done only by a GT-R certified
NISSAN dealer.
When maintenance work is required on the
vehicle, the front air bags, side air bags, curtain
air bags, pretensioners and related parts should
be pointed out to the person conducting the
maintenance. The ignition switch should always
be in the LOCK position when working under
the hood or inside the vehicle.
pretensioners cannot be repaired.
.
The front air bag, side air bag,
curtain air bag and the pretensioner
should be inspected by a GT-R
certified NISSAN dealer if there is
any damage to the front end or side
portion of the vehicle.
.
If you need to dispose of a supplemental air bag or a pretensioner or
scrap the vehicle, contact a GT-R
certified NISSAN dealer. Incorrect
disposal procedures could cause
personal injury.
WARNING
.
Once a front air bag, side air bag, or
curtain air bag has inflated, the air
bag module will not function again
and must be replaced. Additionally,
the activated pretensioners must
also be replaced. The air bag module and pretensioners should be
replaced by a GT-R certified NISSAN
dealer. The air bag module and
1-48 Safety — Seats, seat belts and supplemental restraint system
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(99,1)
2 Instruments and controls
Cockpit ....................................................................................... 2-3
Instrument panel ....................................................................... 2-4
Meters and gauges .................................................................. 2-5
Speedometer ....................................................................... 2-6
Odometer/twin trip odometer ......................................... 2-6
Tachometer .......................................................................... 2-7
Engine coolant temperature gauge ............................... 2-7
Fuel gauge ........................................................................... 2-8
Transmission position indicator ...................................... 2-9
Upshift indicator ................................................................. 2-9
Instrument brightness control ...................................... 2-11
Vehicle information display ................................................. 2-12
Engine oil level display ................................................... 2-12
Transmission system check display ............................ 2-14
Drive computer ...................................................................... 2-15
Current fuel consumption ............................................. 2-15
Vehicle speed ................................................................... 2-16
Cruise control ................................................................... 2-16
Average fuel consumption and speed ....................... 2-16
Elapsed time and trip odometer .................................. 2-17
Distance to empty ........................................................... 2-17
Outside air temperature ................................................ 2-18
Setting (drive computer) ............................................... 2-19
Warning (drive computer) ............................................. 2-23
Warning lights, indicator lights and
audible reminders .................................................................
Checking bulbs .............................................................
Warning lights ................................................................
Indicator lights ...............................................................
Audible reminders .........................................................
Warning display ....................................................................
Engine oil low pressure warning ...............................
Engine system warning ...............................................
Shift lever position warning ........................................
Reverse warning ............................................................
Transmission system warning ....................................
Transmission oil high temperature warning ............
Transmission clutch high temperature warning .....
Parking brake release warning ..................................
Low brake fluid warning ..............................................
Anti-lock Braking System (ABS) warning ..............
Vehicle Dynamic Control (VDC)
system warning ..............................................................
AWD clutch high temperature warning ...................
Front/rear tire size discrepancy warning .................
AWD system warning ..................................................
Low tire pressure warning ..........................................
Run-flat tire warning .....................................................
[ Edit: 2014/ 12/ 8
2-25
2-25
2-25
2-31
2-32
2-33
2-34
2-34
2-35
2-35
2-35
2-36
2-36
2-36
2-37
2-37
2-37
2-38
2-38
2-39
2-39
2-39
Model: R35-D ]
(100,1)
Tire Pressure Monitoring System
(TPMS) warning ...............................................................
Cruise control system warning ....................................
Low fuel warning .............................................................
Door/trunk open warning ..............................................
Headlight system warning .............................................
Low washer fluid warning .............................................
No key warning ................................................................
Operation displays ................................................................
Engine start operation indicator ..................................
Shift “P” warning .............................................................
“PUSH” warning ..............................................................
Steering lock release malfunction indicator .............
Intelligent Key insertion indicator ................................
Intelligent Key removal indicator ..................................
Intelligent Key battery discharge indicator ................
Security systems ...................................................................
Vehicle security system .................................................
NISSAN Vehicle Immobilizer System .........................
Wiper and washer switch ...................................................
Using the wipers .............................................................
Using the washer ............................................................
Rear window defroster switch ...........................................
Headlight and turn signal switch ......................................
Headlight switch ..............................................................
Turn signal switch ...........................................................
2-40
2-40
2-40
2-41
2-41
2-42
2-42
2-43
2-43
2-43
2-44
2-44
2-44
2-45
2-45
2-45
2-45
2-47
2-48
2-49
2-49
2-50
2-50
2-50
2-53
Horn .........................................................................................
Heated seats .........................................................................
Turning on the heaters .................................................
Turning off the heaters .................................................
Power outlets ........................................................................
Storage ...................................................................................
Cup holders ....................................................................
Sunglasses holder ........................................................
Door pocket ....................................................................
Glove box ........................................................................
Console box ...................................................................
Coat hooks .....................................................................
Windows ................................................................................
Power windows .............................................................
Interior lights ..........................................................................
Map lights .......................................................................
Interior light control switch .........................................
Vanity mirror lights ................................................................
HomeLink® Universal Transceiver ....................................
Programming HomeLink® ............................................
Programming HomeLink® for Canadian customers
and gate openers ..........................................................
Operating the HomeLink® universal transceiver ...
Programming troubleshooting ....................................
Clearing the programmed information .....................
Reprogramming a single HomeLink® button .........
If your vehicle is stolen ................................................
[ Edit: 2014/ 12/ 8
2-54
2-54
2-54
2-54
2-55
2-56
2-56
2-57
2-58
2-58
2-59
2-59
2-60
2-60
2-62
2-62
2-63
2-64
2-64
2-65
2-66
2-66
2-67
2-67
2-67
2-67
Model: R35-D ]
(101,1)
COCKPIT
11.
12.
13.
14.
15.
*:
1.
2.
3.
4.
5.
Headlight and turn signal switch (P.2-50)
Paddle shifters (P.5-15)
Steering-wheel-mounted controls (left side)*
Meters and gauges (P.2-5)
Steering-wheel-mounted controls (right side)
— MRK (Mark) switch*
— Cruise control (P.5-34)
6.
7.
8.
9.
10.
Horn (P.2-54)
Tilting/telescopic steering wheel lever (P.3-25)
Push-button ignition switch (P.5-10)
Parking brake (P.5-33, P.5-46)
Shift lever (P.5-15)
Refer to the separate Multi Function Display
Owner’s Manual.
Wiper and washer switch (P.2-48)
VDC, transmission and suspension set up
switches (P.5-25)
Trunk lid release switch (P.3-19)
Hood release handle (P.3-17)
Intelligent Key port (P.5-12)
Instruments and controls 2-3
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(102,1)
INSTRUMENT PANEL
13.
*:
1.
2.
3.
4.
5.
6.
2-4
Outside mirror control switch (P.3-27)
Center dial*
Audio system*
Heater and air conditioner*
Multi function display*
Hazard warning flasher switch (P.6-2)
7.
8.
9.
10.
11.
12.
Trunk release power cancel switch (P.3-20)
Refer to the separate Multi Function Display
Owner’s Manual.
Glove box (P.2-58)
Fuse box cover (P.8-25)
Power outlet (P.2-55)
Rear window defroster switch (P.2-50)
Front passenger air bag status light (P.1-41)
CD/DVD slot*
Instruments and controls
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(103,1)
METERS AND GAUGES
NOTE:
. Meters and gauges will illuminate
when the ignition switch is pushed to
the ON position.
.
1.
2.
3.
4.
5.
6.
Trip A/B reset switch (P.2-6)
Speedometer (P.2-6)
Tachometer (P.2-7)/Upshift indicator (P.2-9)
Transmission position indicator (P.2-9)
Engine coolant temperature gauge (P.2-7)
ENTER switch (P.2-15)
7.
8.
9.
10.
11.
The needle indicators may move
slightly after the ignition switch is
pushed to the OFF position. This does
not indicate that there is a malfunction.
Instrument brightness control switch (P.2-11)
Vehicle information display (P.2-12)
Odometer/twin trip odometer (P.2-6)
Fuel gauge (P.2-8)
NEXT switch (P.2-15)
Instruments and controls 2-5
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(104,1)
liquid may cause the system to
malfunction.
SPEEDOMETER
The speedometer indicates the vehicle speed.
CAUTION
.
.
2-6
For cleaning, use a soft cloth, dampened with water. Never use a rough
cloth, alcohol, benzine, thinner or
any kind of solvent or paper towel
with a chemical cleaning agent.
They will scratch or cause discoloration to the lens.
Do not spray any liquid such as
water on the meter lens. Spraying
ODOMETER/TWIN TRIP ODOMETER
1 indicates the total distance
The odometer *
that the vehicle has been driven.
2
The twin trip odometer *
indicates the
distance of individual trips.
Changing the display
Push the TRIP A/B RESET switch to change
A and &
B .
between trips &
Resetting the trip odometer
To reset a trip, display the trip that you want to
reset to zero, then push and hold the TRIP A/B
Instruments and controls
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(105,1)
RESET switch for more than 1 second.
NOTE:
When the battery is disconnected, the
A and &
B is erased,
memory for trips &
and both return to zero.
TACHOMETER
The tachometer indicates the engine speed in
revolutions per minute (rpm). Do not rev the
1 .
engine into the red zone *
NOTICE
When engine speed approaches the red
zone, shift to a higher gear or reduce
engine speed. Operating the engine in
the red zone may cause serious engine
damage.
ENGINE COOLANT TEMPERATURE
GAUGE
The gauge indicates the engine coolant temperature.
The engine coolant temperature is within the
normal range when the gauge needle points
1 shown in the illustration.
within the zone *
The engine coolant temperature varies with the
outside air temperature and driving conditions.
Instruments and controls 2-7
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(106,1)
the fuel gauge needle reaches “E”. (
“Low
fuel warning” page 2-40)
The
indicates that the fuel-filler door is
located on the passenger’s side of the vehicle.
(
“Fuel-filler door” page 3-23)
NOTICE
If the gauge indicates engine coolant
temperature near the hot (H) end of the
normal range, reduce vehicle speed to
decrease temperature. If gauge is over
the normal range, stop the vehicle as
soon as safely possible. If the engine is
overheated, continued operation of the
vehicle may seriously damage the engine. (
“If your vehicle overheats”
page 6-8)
NOTE:
If the vehicle runs out of fuel, the
Malfunction Indicator Light (MIL) may
come on. Refuel as soon as possible. After
a few driving trips, the
light should
turn off. If the light remains on after a few
driving trips, have the vehicle inspected by
a GT-R certified NISSAN dealer.
FUEL GAUGE
(
“Malfunction Indicator Light (MIL)”
page 2-31)
The gauge indicates the approximate fuel level
in the tank.
The gauge may move slightly during braking,
turning, acceleration, or going up or down hills.
The gauge needle returns to E (Empty) after the
ignition switch is pushed to the LOCK position.
Refill the fuel tank before the gauge
registers “E” (Empty).
The low fuel warning will be indicated on the
vehicle information display when the fuel tank is
getting low. Refuel as soon as it is convenient,
preferably before the gauge reaches “E”. There
will be a small reserve of fuel in the tank when
2-8
Instruments and controls
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(107,1)
TRANSMISSION POSITION INDICATOR
The transmission position indicator indicates the
gear positions.
The indicator blinks if it is not possible to shift
M position.
the gear when in the &
1.
2.
3.
Upshift indicator (green)
Upshift indicator (yellow)
Upshift indicator (red)
UPSHIFT INDICATOR
When the upshift indicator is set to on, the
indicators on the tachometer will illuminate to
help upshift at a constant engine speed from any
gear or to warn the driver of over-revving.
The upshift indicator operates only when the
M position. This function
shift lever is in the &
consists of two modes that can be selected on
the vehicle information display: AUTO setting
and MANUAL setting.
Instruments and controls 2-9
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(108,1)
Setting
Push the ignition switch to the ON position. Use
the ENTER switch
and toggle the vehicle
information display to show the SETTING
screen.
Use the NEXT switch
and ENTER switch
2-10 Instruments and controls
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(109,1)
to go to ALERT > UPSHIFT. The current
status of the upshift indicator will be shown on
the UPSHIFT screen. Note that the function is
set to AUTO as the factory default setting.
To change the upshift indicator mode, choose
SETTING on the UPSHIFT screen. Set one of
the following modes by pushing the NEXT
switch
, and then push ENTER
to
complete.
.
AUTO
.
3,000 to 6,300 RPM (MANUAL)
. OFF
The number will increase by 100 RPM. To
increase the number by 500 RPM, push and
hold the NEXT switch
.
Example
When the maximum engine speed is
desired:
Set the upshift indicator to AUTO. The yellow
indicator illuminates approximately 700 RPM
before the red zone, and the red indicator
illuminates just before the red zone.
When the maximum engine torque is
desired:
Set the figure at 6,000 RPM. The green
indicator starts flashing from approximately
5,500 RPM and illuminates at 6,000 RPM.
When breaking-in the vehicle:
To help avoid high engine speeds during breakin, set the upshift indicator to less than 3,500
RPM. The green indicator starts flashing approximately 500 RPM before the set figure and
illuminates from the set figure. (
“Break-in
schedule” page 5-39)
NOTE:
. There may be a slight difference between the timing of the upshift indicator illumination and the tachometer
indication.
.
When the battery terminal is disconnected, the set memory will be erased
and the mode returns to the default.
INSTRUMENT BRIGHTNESS CONTROL
The instrument brightness can be adjusted
when the ignition switch is in the ON position.
1
Push the switch to adjust the brightness up *
2 . The brightness level is shown on
or down *
the vehicle information display.
When the headlights are on, the brightness of
the interior switches is also adjusted at the same
time.
Instruments and controls 2-11
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(110,1)
VEHICLE INFORMATION DISPLAY
NOTE:
. The instrument brightness can be adjusted separately for daytime and
nighttime conditions. The adjusted settings are automatically stored.
The vehicle information display can display the
following information.
.
When the battery terminal is disconnected, the set memory will be erased
and the setting returns to the default.
.
Engine oil level display
.
Transmission system check display
.
Instrument brightness control level display
(
“Instrument brightness control” page
2-11)
.
Drive computer
(
“Drive computer” page 2-15)
.
Warning display
(
“Warning display” page 2-33)
.
Operation display
“Operation displays” page 2-43)
(
.
Cruise control display
(
“Cruise control” page 5-34)
ENGINE OIL LEVEL DISPLAY
When the ignition switch is pushed to the ON
position, the engine oil status before starting the
engine is indicated as illustrated.
When the oil level is normal
“OIL LEVEL OK” is displayed. Push the displayed LEVEL switch
to check the oil level.
2-12 Instruments and controls
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(111,1)
NOTICE
If the vehicle is in a location that is not
level, accurate measurement of the oil
level may not be possible. If “OIL LEVEL
LOW ” is displayed, but the level shown
by the oil dipstick is normal, move the
vehicle to a level location and stop the
engine. After at least 5 minutes have
passed, open the driver’s door and push
the ignition switch back to ON. If the
“OIL LEVEL LOW” message appears
again, have engine oil added or the oil
changed.
NOTE:
When the oil level is low
The engine oil level can be displayed after
the “OIL LEVEL OK” display turns off or
while the engine is started and running.
(
“Maintenance” page 2-20)
If the message shown above is displayed, the
engine oil level is low.
Warm up the engine in a level location. After at
least 5 minutes have passed since engine stop,
use the engine oil dipstick to check the oil level.
(
“Engine oil” page 8-13)
If the oil level is low, have additional engine oil
added, or the oil changed, at a GT-R certified
NISSAN dealer.
Instruments and controls 2-13
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(112,1)
after the system check is finished.
Release the button and push it again
to operate the shift lever.
.
When the oil level sensor malfunction occurs
TRANSMISSION SYSTEM CHECK
DISPLAY
If the message shown above is displayed, the
engine oil level sensor may be malfunctioning.
Contact a GT-R certified NISSAN dealer immediately.
This is displayed after the engine is started while
the transmission system is being checked. It
turns off after a few seconds.
During winter or at other times when
the temperature is extremely low,
changes in the hydraulic response
characteristic s may increase the
amount of time that is required for the
system check. During the system check,
a thudding operating noise may occur
or the engine speed may decrease,
however this does not indicate that
there is a malfunction.
NOTE:
. During the system check, the shift lever
P position.
cannot be moved out of the &
Operate the shift lever after the system
check indicator turns off.
.
The shift lever cannot be moved if the
shift lever button is pushed while the
system check is being performed, even
2-14 Instruments and controls
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(113,1)
DRIVE COMPUTER
.
Setting
. Warning
3
The vehicle information display *
can be
changed when the ignition switch is in the ON
1 to
position. Push the ENTER switch
*
change the display.
NOTE:
. The cruise control display is shown if
cruise control is set. (
“Cruise control” page 5-34)
1.
2.
3.
ENTER switch
NEXT switch
Vehicle information display
The drive computer displays the following
information:
.
Current fuel consumption
.
Vehicle speed
.
Cruise control
.
Average fuel consumption and speed
.
Elapsed time and trip computer
.
Distance to empty
.
Outside air temperature
.
The warning display is not shown if
there are no conditions to warn the
driver.
.
Depending on the driving conditions
and other factors, the displayed values
may differ from the actual values.
.
CURRENT FUEL CONSUMPTION
The current fuel economy is displayed when
driving.
The position of the speedometer needle and the speed shown in the vehicle
information display may slightly differ.
Instruments and controls 2-15
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(114,1)
VEHICLE SPEED
CRUISE CONTROL
This displays the vehicle speed while driving.
This displays the set cruise control status.
NOTE:
The cruise control display is shown if
cruise control is set. (
“Cruise control”
page 5-34)
AVERAGE FUEL CONSUMPTION
AND SPEED
This displays the average fuel economy and
average vehicle speed beginning from the time
when the display was last reset.
To reset the display, push and hold the NEXT
switch
for more than 1 second. (The
average fuel economy and average vehicle
speed are reset at the same time.)
2-16 Instruments and controls
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(115,1)
NOTE:
” is displayed during the first 1/3
. “
mile (500 m) or the first 30 seconds
after a reset.
.
The values are updated approximately
every 30 seconds.
ELAPSED TIME AND TRIP ODOMETER
This displays the elapsed time and trip odometer
beginning from the time when the display was
last reset.
To reset the display, push and hold the NEXT
switch
for more than 1 second. (The
elapsed time and trip odometer are reset at
the same time.)
DISTANCE TO EMPTY
This displays the approximate distance that the
vehicle can be driven based on the amount of
fuel remaining in the fuel tank and the actual fuel
consumption.
NOTE:
. If the fuel level is low, the low fuel
warning will be displayed. (
“Low
fuel warning” page 2-40)
.
If the vehicle is not refueled after the
low fuel warning appears, the display
will change to “
”. This change
timing may become earlier depending
Instruments and controls 2-17
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(116,1)
partment is high.
on the driving conditions. This does not
indicate that there is a malfunction.
.
.
The values are updated approximately
every 30 seconds.
When the outside air temperature is
lower than 378F (38C), the low outside
temperature warning will be displayed
and “ICY” is indicated on the outside
air temperature display. (
“Alert”
page 2-19)
OUTSIDE AIR TEMPERATURE
This displays the outside air temperature.
NOTE:
. The outside air temperature may not be
displayed correctly in the following
cases.
— The outside air temperature is lower
than −228F (−308C) or is higher than
1318F (558C).
— The vehicle is stopped or is driving
at a low speed (less than approximately 12 MPH (20 km/h)).
— The temperature in the engine com-
2-18 Instruments and controls
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(117,1)
NOTE:
. When the battery terminal is disconnected, the set memory will be erased
and the settings return to the default.
.
Setting is not possible in the following
cases.
— The vehicle is being driven.
— A warning display is active.
— The instrument brightness control
level display is active.
— The cruise control status is displayed.
SETTING (drive computer)
Alert
This is used to set the alert, maintenance and
optional settings.
to select an item, then
Use the NEXT switch
confirm with the ENTER switch
to change
to the corresponding setting screen.
To return to the initial setting screen, push and
hold the ENTER switch
for more than 1
second.
This function can be used to make settings for
the upshift indicator, “time to rest” indicator and
low outside temperature warning.
Upshift indicator:
For details concerning the upshift indicator, refer
to the following section. (
“Upshift indicator” page 2-9)
Instruments and controls 2-19
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(118,1)
“TIMER” indicator:
This alert informs the driver that the set driving
time has elapsed.
On the TIMER screen, push the NEXT switch
to change the time. Push and hold the
switch to increase the number every 1 hour. A
maximum of 6 hours can be set.
NOTE:
The default setting is OFF.
Low outside temperature warning:
This alert informs the driver when the outside air
temperature is lower than 378F (38C).
On the ICY screen, push the NEXT switch
to turn this warning ON/OFF.
Maintenance
NOTE:
NOTE:
The default setting is ON.
Because these are displayed based on the
mileage driven, they do not indicate the
actual conditions of the vehicle. Use these
functions only as a reference.
Input the maintenance distance using the
following items:
This function can be used to set the various
maintenance intervals and to check the engine
oil level. The reminders shown below are used to
notify the driver of the maintenance intervals.
.
On each setting screen, push the NEXT
2-20 Instruments and controls
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(119,1)
switch
to change the mileage. Push and
hold the switch to increase the number every
600 miles (1,000 km).
.
Set to “—” to set no reminders.
.
To reset the accumulated mileage to zero,
go to the RESET screen, then push the
NEXT switch
and confirm with the
ENTER switch
.
NOTE:
. To restore the mileage to the original
figure after resetting, push the NEXT
switch
again.
.
When the battery terminal is disconnected, the set mileage will be erased
and the settings will return to their
default settings.
Engine oil level:
This can be used to check the pre-start oil level
while the engine is running. Select SETTING >
MAINTENANCE > OIL > ENGINE OIL >
LEVEL.
If the low level reminder appears, check the level
using the engine oil dipstick. (
“Checking
engine oil level” page 8-13)
Engine oil:
When the customer set mileage approaches,
the reminder will appear on the display and the
remaining distance is displayed at regular
intervals. Select SETTING > MAINTENANCE
> OIL > ENGINE OIL to set or reset the mileage
for the engine oil change.
NOTE:
The default setting is 9,500 miles (15,000
km). The maximum mileage that can be set
is 9,500 miles (15,000 km).
Instruments and controls 2-21
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(120,1)
Engine oil filter:
The reminder is displayed when the customer
set mileage is exceeded. Select SETTING >
MAINTENANCE > FILTER to set or reset the
mileage for the engine oil filter change.
NOTE:
The default setting is 9,500 miles (15,000
km). The maximum mileage that can be set
is 9,500 miles (15,000 km).
Transmission oil:
The reminder is displayed when the customer
set mileage is exceeded. Select SETTING >
MAINTENANCE > OIL > T/M OIL to set or
reset the mileage for the transmission oil
change.
NOTE:
The default setting is 37,000 miles (60,000
km). The maximum mileage that can be set
is 55,500 miles (90,000 km).
Tires:
This reminder appears when the customer set
distance comes for maintaining tires. You can
set or reset the distance for maintaining tires.
(See
“Setting (drive computer)” page 2-19
earlier in this section.)
WARNING
The tire maintenance indicator is not a
substitute for regular tire checks, including tire pressure checks. See
“Changing wheels and tires” in the “8.
Maintenance and do-it-yourself” section. Many factors including tire infla-
2-22 Instruments and controls
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(121,1)
tion, alignment, driving habits and road
conditions affect tire wear and when
tires should be replaced. Setting the
tire maintenance reminder for a certain
driving distance does not mean your
tires will last that long. Use the tire
maintenance reminder as a guide only
and always perform regular tire checks.
Failure to perform regular tire checks,
including tire pressure checks could
result in tire failure. Serious vehicle
damage could occur and may lead to a
collision, which could result in serious
personal injury or death.
NOTE:
The default setting is OFF.
Options
WARNING (drive computer)
This function can be used to make settings for
language and unit.
Warning information is displayed on the vehicle
information display.
while a warning
Push the ENTER switch
display is active to return to the original display.
It is also possible to check any warnings that
have not been corrected. (
“Warning display” page 2-33)
Language:
Select ENGLISH or FRANCAIS for use in the
vehicle information display.
Unit:
Select METRIC or US for use in the vehicle
information display.
Checking the warnings
Use the NEXT switch
to select “DETAIL”,
then confirm with the ENTER switch
.
When there are multiple warnings, push the
to change the display
ENTER switch
Instruments and controls 2-23
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(122,1)
among them.
To return to the initial warning, push and hold the
for more than 1 second.
ENTER switch
NOTE:
If there are no warnings to display, only
“SKIP” can be selected.
2-24 Instruments and controls
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(123,1)
WARNING LIGHTS, INDICATOR
LIGHTS AND AUDIBLE REMINDERS
All-Wheel Drive (AWD) warning light
Low tire pressure warning light
Cruise set switch indicator light
Master warning light
Exterior light indicator
Seat belt warning light
Front passenger air bag status light
Supplemental air bag warning light
High beam indicator light
Transmission warning light
Malfunction Indicator Light (MIL)
Charge warning light
Vehicle Dynamic Control (VDC) warning
light
Turn signal/hazard indicator lights
Engine oil pressure warning light
Cruise main switch indicator light
Vehicle Dynamic Control (VDC) off indicator
light
Anti-lock Braking System (ABS) warning
light
Brake warning light
Intelligent Key warning light
CHECKING BULBS
a GT-R certified NISSAN dealer.
With all doors closed, apply the parking brake
and push the ignition switch to the ON position
without starting the engine. The following lights
will come on:
,
or
,
,
,
,
The following lights come on briefly and then go
off:
,
or
,
,
,
,
,
If any light does not come on, it may indicate a
burned-out bulb or an open circuit in the
electrical system. Have the system checked by
WARNING LIGHTS
All-Wheel Drive (AWD) warning light
The
warning light comes on when the
ignition switch is pushed to ON. It turns off soon
after the engine is started.
If the AWD system malfunctions, the warning
light will either remain illuminated or blink.
(
“All-Wheel Drive (AWD)” page 5-41)
CAUTION
.
If the warning light comes on while
driving there may be a malfunction
in the AWD system. Reduce the
vehicle speed and have your vehicle
checked by a GT-R certified NISSAN
dealer as soon as possible.
.
If the AWD warning light blinks on
when you are driving:
— blinks rapidly (about twice a
second):
Instruments and controls 2-25
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(124,1)
Pull off the road in a safe area,
and idle the engine. The driving
mode will change to RWD to
prevent the AWD system from
malfunctioning. If the warning
light turns off, you can drive
again. This does not indicate
that there is a malfunction.
— blinks slowly (about once every
2 seconds):
Pull off the road in a safe area,
and idle the engine. Check that
all tire sizes are the same as
that specified on the Tire and
Loading Information label located in the driver’s door opening, tire pressure is correct and
tires are not worn. (
“Tire
and loading information label”
page 9-13)
If the tire pressure is insufficient, fill with nitrogen gas.
Contact a GT-R certified NISSAN
dealer about filling with nitrogen gas. If nitrogen gas is not
available, compressed air may
be safely used under normal
driving conditions. However,
NISSAN recommends refilling
with nitrogen gas for maximum
tire performance.
.
If the warning light is still on after
the above operations, have your
vehicle checked by a GT-R certified
NISSAN dealer as soon as possible.
or
Anti-lock Braking
System (ABS) warning light
When the ignition switch is in the ON position,
the Anti-lock Braking System (ABS) warning
light illuminates and then turns off. This indicates
the ABS is operational.
If the ABS warning light illuminates while the
engine is running, or while driving, it may
indicate the ABS is not functioning properly.
Have the system checked by a GT-R certified
NISSAN dealer.
If an ABS malfunction occurs, the anti-lock
function is turned off. The brake system then
operates normally, but without anti-lock assistance. (
“Brake system” page 5-48)
or
Brake warning light
This light functions for both the parking brake
and the foot brake systems.
Parking brake indicator:
When the ignition switch is in the ON position,
the light comes on when the parking brake is
applied.
Low brake fluid warning light:
When the ignition switch is in the ON position,
the light warns of a low brake fluid level. If the
light comes on while the engine is running with
the parking brake not applied, stop the vehicle
and perform the following:
1. Check the brake fluid level. Add brake fluid
as necessary. (
“Brake fluid” page 815)
2. If the brake fluid level is correct, have the
warning system checked by a GT-R certified
NISSAN dealer.
Anti-lock Braking System (ABS) warning
indicator:
When the parking brake is released and the
brake fluid level is sufficient, if both the brake
warning light and the Anti-lock Braking System
(ABS) warning light illuminate, it may indicate
the ABS is not functioning properly. Have the
brake system checked, and if necessary repaired, by a GT-R certified NISSAN dealer
promptly. (
“Anti-lock Braking System
(ABS) warning light” page 2-26)
2-26 Instruments and controls
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(125,1)
WARNING
.
Your brake system may not be
working properly if the warning light
is on. Driving could be dangerous. If
you judge it to be safe, drive carefully to the nearest service station
for repairs. Otherwise, have your
vehicle towed because driving it
could be dangerous.
.
Pressing the brake pedal with the
engine stopped and/or low brake
fluid level may increase your stopping distance and braking will require greater pedal effort as well as
pedal travel.
.
If the brake fluid level is below the
minimum or MIN mark on the brake
fluid reservoir, do not drive until the
brake system has been checked at a
GT-R certified NISSAN dealer.
Charge warning light
If the light comes on while the engine is running,
it may indicate the charging system is not
functioning properly. Turn the engine off and
check the alternator belt. If the belt is loose,
broken, missing or if the light remains on, see a
GT-R certified NISSAN dealer immediately.
NOTICE
Do not continue driving if the alternator
belt is loose, broken or missing.
Engine oil pressure warning
light
This light warns of low engine oil pressure. If the
light flickers or comes on during normal driving,
pull off the road in a safe area, stop the engine
immediately and call a GT-R certified NISSAN
dealer.
The engine oil pressure warning light is
not designed to indicate a low oil level.
Check the vehicle information display or
use the dipstick to check the oil level.
(
“Engine oil level display” page 2-12)
(
“Checking engine oil level” page 8-13)
NOTICE
Running the engine with the engine oil
pressure warning light on could cause
serious damage to the engine almost
immediately. Turn off the engine as
soon as it is safe to do so.
Intelligent Key warning light
After the ignition switch is pushed to the ON
position, this light comes on for about 2 seconds
and then turns off.
This light warns of a malfunction with the
electrical steering lock system or the Intelligent
Key system.
If the light comes on while the engine is
stopped, it may be impossible to free the
steering lock or to start the engine. If the light
comes on while the engine is running, you can
drive the vehicle. However in these cases,
contact a GT-R certified NISSAN dealer for
repair as soon as possible.
Low tire pressure warning light
Your vehicle is equipped with a Tire Pressure
Monitoring System (TPMS) that monitors the tire
pressure of all tires.
The low tire pressure warning light warns of low
tire pressure and flat tire, or indicates that the
TPMS is not functioning properly.
After the ignition switch is pushed to the ON
position, the warning light illuminates for about 1
second and turns off.
Instruments and controls 2-27
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(126,1)
Low tire pressure warning:
If the vehicle is being driven with low tire
pressure, the warning light will illuminate.
When the low tire pressure warning light
illuminates, you should stop and adjust the
tire pressure of all 4 wheels to the
recommended COLD tire pressure shown
on the Tire and Loading Information label
located in the driver’s door opening.
The low tire pressure warning light does
not automatically turn off when the tire
pressure is adjusted. After the tire is
inflated to the recommended pressure,
the vehicle must be driven at speeds above
16 MPH (25 km/h) to activate the TPMS
and turn off the low tire pressure warning
light. Use a tire pressure gauge to check
the tire pressure. (
“Tire Pressure
Monitoring System (TPMS)” page 5-4)
(
“Tire Pressure Monitoring System
(TPMS)” page 6-3)
Run-flat tire warning:
The run-flat tire warning warns of a flat tire.
If the vehicle is being driven with one or more flat
tires, the warning light will illuminate continuously and a chime will sound for 10 seconds.
The chime will only sound at the first indication
of a flat tire and the warning light will illuminate
continuously. When the flat tire warning is
activated, have the system reset and the tire
checked and replaced if necessary by a GT-R
certified NISSAN dealer. Even if the tire is
inflated to the specified COLD tire pressure, the
warning light will continue to illuminate until the
system is reset by a GT-R certified NISSAN
dealer.
If you select the tire pressure information in the
multi function display, the warning message will
be displayed. The tire pressure for each tire will
also be displayed. Refer to the separate Multi
Function Display Owner’s Manual.
Your vehicle can be driven for a limited time on a
flat tire. (
“Run-flat tires” page 6-4)
(
“Run-flat tires” page 8-39)
TPMS malfunction:
If the TPMS is not functioning properly, the low
tire pressure warning light will flash for approximately 1 minute when the ignition switch is
pushed to the ON position. The light will remain
on after the 1 minute. Have the system checked
by a GT-R certified NISSAN dealer. (
“Tire
Pressure Monitoring System (TPMS)” page 5-4)
(
“Tire pressure” page 8-32)
WARNING
.
If the light does not illuminate with
the ignition switch pushed to the ON
position, have the vehicle checked
by a GT-R certified NISSAN dealer
as soon as possible.
.
If the light illuminates while driving,
avoid sudden steering maneuvers or
abrupt braking, reduce vehicle
speed, pull off the road to a safe
location and stop the vehicle as
soon as possible. Driving with under-inflated tires may permanently
damage the tires and increase the
likelihood of tire failure. Serious
vehicle damage could occur and
may lead to an accident and could
result in serious personal injury.
Check the tire pressure for all four
tires. Adjust the tire pressure to the
recommended COLD tire pressure
shown on the Tire and Loading
Information label located in the
driver’s door opening to turn the
low tire pressure warning light off. If
the light still illuminates while driving after adjusting the tire pressure,
a tire may be flat.
2-28 Instruments and controls
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(127,1)
.
.
.
.
dealer as soon as possible for tire
replacement and/or system resetting.
Although you can continue driving
with a punctured run-flat tire, remember that vehicle handling stability is reduced, which could lead to
an accident and personal injury.
Also, driving a long distance at high
speeds may damage the tires.
.
Do not drive at speeds above 50
MPH (80 km/h) and do not drive
more than 50 miles (80 km) with a
punctured run-flat tire. The actual
distance the vehicle can be driven
on a flat tire depends on outside
temperature, vehicle load, road conditions and other factors.
If you detect any unusual sounds or
vibrations while driving with a punctured run-flat tire, pull off the road
to a safe location and stop the
vehicle as soon as possible. The tire
may be seriously damaged and
need to be replaced.
When a wheel is replaced, the TPMS
will not function and the low tire
pressure warning light will flash for
approximately 1 minute. The light
will remain on after the 1 minute.
Contact a GT-R certified NISSAN
Replacing tires with those not originally specified by NISSAN could
affect the proper operation of the
TPMS.
CAUTION
.
The TPMS is not a substitute for the
regular tire pressure check. Be sure
to check the tire pressure regularly.
.
Be sure to install the specified size
of tires on the four wheels.
NOTE:
. If the vehicle is being driven at speeds
of less than 16 MPH (25 km/h), the
TPMS may not operate correctly.
.
The tires of this vehicle are filled with
nitrogen gas. When the tire pressure is
low, fill the tires with nitrogen gas.
Contact a GT-R certified NISSAN dealer
for information on filling the tires with
nitrogen gas.
Master warning light
When the ignition switch is in the ON position,
the master warning light illuminates if any of the
warning displays appear on the vehicle information display. (
“Warning display” page 233)
Seat belt warning light and
chime
The light and chime remind you to fasten seat
belts. The light illuminates whenever the ignition
switch is pushed to the ON position, and will
remain illuminated until the driver’s seat belt is
fastened. At the same time, the chime will sound
for about 6 seconds unless the driver’s seat belt
is securely fastened.
The seat belt warning light for the front
passenger will illuminate if the seat belt is not
fastened when the front passenger’s seat is
occupied. For approximately 5 seconds after the
ignition switch is in the ON position, the system
does not activate the warning light for the front
passenger. (
“Seat belts” page 1-6)
Supplemental air bag warning
light
After pushing the ignition switch to the ON
position, the supplemental air bag warning light
will illuminate for about 7 seconds and then turn
Instruments and controls 2-29
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(128,1)
off. This means the system is operational.
If any of the following conditions occur, the front
air bag, side air bag, curtain air bag and
pretensioner systems need servicing and your
vehicle must be taken to a GT-R certified
NISSAN dealer.
.
The supplemental air bag warning light
remains on after approximately 7 seconds.
.
The supplemental air bag warning light
flashes intermittently.
.
The supplemental air bag warning light does
not come on at all.
Unless checked and repaired, the supplemental
restraint system (air bag system) and/or the
pretensioners may not function properly.
(
“Supplemental restraint system” page 134)
Transmission warning light
This light warns of the following malfunctions.
Transmission system malfunction:
The light blinks if a malfunction in the transmission system occurs. If the light blinks, certain
gear positions may become unusable, so that
the vehicle may become undrivable. Have the
system inspected promptly by a GT-R certified
NISSAN dealer.
Transmission oil temperature high:
The light illuminates if the transmission oil
temperature becomes unusually high. If the light
illuminates, avoid driving at high speed or at high
engine speed until the light turns off. The light
will turn off after a short period of time and the
vehicle can then be driven normally. If the light
illuminates frequently, contact a GT-R certified
NISSAN dealer.
Transmission clutch temperature high:
The light illuminates if clutch temperature
becomes unusually high. If the light illuminates,
pull off the road in a safe area and idle the
engine. When the light turns off, driving can be
resumed. If the light illuminates frequently,
contact a GT-R certified NISSAN dealer.
NOTICE
.
Continuing to drive with the light on
could cause serious damage to the
transmission.
.
If the light continues to illuminate,
the vehicle cannot be driven because the engine output may be
reduced and the clutch may be
reduced to keep the clutch disengaged.
WARNING
If the supplemental air bag warning
light is on, it could mean that the front
air bag, side air bag, curtain air bag
and/or pretensioner systems will not
operate in an accident. To help avoid
injury to yourself or others, have your
vehicle checked by a GT-R certified
NISSAN dealer as soon as possible.
NOTICE
If the light continues to illuminate, the
engine output may be reduced to prevent transmission damage.
R mode start function:
If the R mode start function is used 4 times
continuously, the function may be disabled and
cannot be turned on for protection. While the
function is disabled, the warning light illuminates. When the warning light goes off, the
function can be used again. (
“R mode start
function” page 5-32)
2-30 Instruments and controls
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(129,1)
When the warning light illuminates, perform cool
down driving (driving 1.3 mile (2 km) in 5th or
6th gear at a speed of approximately 37 - 50
MPH (60 - 80 km/h) while checking the
temperature of the transmission oil until the
warning light goes off.
(
“Vehicle Dynamic Control (VDC) system”
page 5-50)
NOTICE
The light comes on when the cruise control is
pushed. The light turns off when the main switch
is pushed again. While the cruise control system
main switch indicator light is on, the cruise
control system is operational.
While the warning light is illuminated,
the engine output is controlled so that
it does not increase.
INDICATOR LIGHTS
Cruise main switch indicator
light
Front passenger air bag status
light
The front passenger air bag status light (
)
will be lit and the passenger front air bag will be
OFF depending on how the front passenger
seat is being used. (
“NISSAN Advanced
Air Bag System (front seats)” page 1-40)
High beam indicator light
This light comes on when the headlight high
beam is on and goes out when the low beam is
selected.
Cruise set switch indicator
Vehicle Dynamic Control (VDC)
warning light
The light will blink when the VDC system or the
traction control system is operating, thus alerting
the driver that the vehicle is nearing its traction
limits. The road surface may be slippery.
If the VDC warning light illuminates when the
VDC system is turned on, this light alerts the
driver to the fact that the VDC system’s fail-safe
mode is operating, for example the VDC or hill
start assist system may not be functioning
properly. Have the system checked by a GT-R
certified NISSAN dealer. If a malfunction occurs
in the system, the VDC system function will be
canceled but the vehicle is still driveable.
light
The light comes on while the vehicle speed is
controlled by the cruise control system. If the
light blinks while the engine is running, it may
indicate the cruise control system is not
functioning properly. Have the system checked
by a GT-R certified NISSAN dealer.
Exterior light indicator
This indicator illuminates when the headlight
switch is turned to the AUTO,
or
position and the front parking lights, instrument
panel lights, rear combination lights, license
plate lights or headlights are on. The indicator
turns off when these lights are turned off.
Malfunction Indicator Light
(MIL)
If the malfunction indicator light comes on
steady or blinks while the engine is running, it
may indicate a potential emission control malfunction.
The malfunction indicator light may also come on
steady if the fuel-filler cap is loose or missing, or
if the vehicle runs out of fuel. Check to make
sure the fuel-filler cap is installed and closed
tightly, and that the vehicle has at least 3 US
gallons (12 liters) of fuel in the fuel tank.
After a few driving trips, the
light should
turn off if no other potential emission control
system malfunction exists.
If this indicator light remains on for 20 seconds
Instruments and controls 2-31
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(130,1)
and then blinks for 10 seconds when the engine
is not running, it indicates that the vehicle is not
ready for an emission control system inspection/
maintenance test. (
“Readiness for Inspection/Maintenance (I/M) test (US only)” page 920)
Operation:
The malfunction indicator light will come on in
one of two ways:
.
.
Malfunction indicator light on steady — An
emission control system malfunction has
been detected. Check the fuel-filler cap. If
the fuel-filler cap is loose or missing, tighten
or install the cap and continue to drive the
vehicle. The
light should turn off after a
few driving trips. If the
light does not
turn off after a few driving trips, have the
vehicle inspected by a GT-R certified
NISSAN dealer. You do not need to have
your vehicle towed to the dealer.
Malfunction indicator light blinking — An
engine misfire has been detected which may
damage the emission control system.
To reduce or avoid emission control system
damage:
1) Do not drive at speeds above 45 MPH
(72 km/h).
2) Avoid hard acceleration or deceleration.
3) Avoid steep uphill grades.
4) If possible, reduce the amount of cargo
being hauled or towed.
The malfunction indicator light may stop
blinking and remain on.
Have the vehicle inspected by a GT-R
certified NISSAN dealer. You do not need
to have your vehicle towed to the dealer.
NOTICE
Continued vehicle operation without
having the emission control system
checked and repaired as necessary
could lead to poor driveability, reduced
fuel economy, and possible damage to
the emission control system.
Turn signal/hazard indicator
lights
The light flashes when the turn signal switch
lever or hazard switch is turned on.
Vehicle Dynamic Control (VDC)
off indicator light
When the ignition switch is in the ON position,
the Vehicle Dynamic Control (VDC) off indicator
light illuminates and then turns off.
The light comes on when the VDC set up switch
is pushed to OFF for more than 1 second.
(
“VDC, transmission and suspension setup
switches” page 5-25)
This indicates that the vehicle dynamic control
system and traction control system are not
operating. (
“Vehicle Dynamic Control
(VDC) system” page 5-50)
AUDIBLE REMINDERS
Key reminder chime
A chime will sound if the driver side door is
opened while the ignition switch is pushed to
the ACC position or pushed to the OFF or
LOCK position with the Intelligent Key left in the
Intelligent Key port. Make sure the ignition
switch is pushed to the OFF position, and take
the Intelligent Key with you when leaving the
vehicle.
Light reminder chime
A chime will sound when the driver side door is
opened with the light switch in the
or
position and the ignition switch in the ACC, OFF
or LOCK position.
Turn the light switch off when you leave the
vehicle.
2-32 Instruments and controls
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(131,1)
WARNING DISPLAY
Parking brake reminder chime
A chime will sound if the vehicle speed is above
4 MPH (7 km/h) with the parking brake applied.
Stop the vehicle and release the parking brake.
Reverse warning chime
The chime will sound inside the vehicle if any of
the following conditions occurs.
.
The driver’s door is opened while the shift
R position and the ignition
lever is in the &
switch is in the ON position.
R position and 5
The shift lever is in the &
minutes have passed while the ignition
switch is in the ON position.
R
Be sure to move the shift lever out of the &
position after driving in reverse.
.
Brake pad wear warning
The disc brake pads have audible wear warnings. When a brake pad requires replacement, it
will make a high pitched scraping sound when
the vehicle is in motion. This scraping sound will
first occur only when the brake pedal is
depressed. After the wear of the brake pad is
increased, the sound will be heard all the time
even if the brake pedal is not depressed. Have
the brakes checked as soon as possible if the
warning sound is heard.
WARNING
When the warning light illuminates or
blinks and a warning is displayed,
promptly take the appropriate action.
Ignoring the warning may result in
malfunctions and accidents.
When the items mentioned below are detected
1 illuminates and the
the master warning light *
warning is displayed on the vehicle information
2 . A chime also sounds.
display *
Instruments and controls 2-33
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(132,1)
If there are multiple warnings, the warning lights
remain lit or continue to blink and the warnings
displayed in the vehicle information display are
switched at regular intervals. The warnings
displayed in the vehicle information display can
be switched voluntarily by pushing the ENTER
switch
.
ENGINE OIL LOW PRESSURE
WARNING
This will appear if the engine oil pressure is low.
(
“Engine oil pressure warning light” page
2-27)
ENGINE SYSTEM WARNING
This will appear if a potential emission control
malfunction is detected, the fuel-filler cap is
loose or missing, or the vehicle runs out of fuel.
(
“Malfunction Indicator Light (MIL)” page
2-31)
2-34 Instruments and controls
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(133,1)
SHIFT LEVER POSITION WARNING
REVERSE WARNING
This will appear if the system cannot detect the
shift lever position.
Stop the vehicle in a safe location. Depress the
brake pedal and move this shift lever to another
position then move the lever back to the desired
position. If the warning is still displayed after the
above operation is performed, have the system
checked by a GT-R certified NISSAN dealer.
(
“Driving the vehicle” page 5-15)
This will appear (and a chime will sound) if the
R position for more than 5
shift lever is in the &
minutes, or when the driver’s door is opened
R position.
while the shift lever is in the &
TRANSMISSION SYSTEM WARNING
This will appear if a transmission system
malfunction occurs. (
“Transmission warning light” page 2-30)
Instruments and controls 2-35
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(134,1)
TRANSMISSION OIL HIGH TEMPERATURE WARNING
TRANSMISSION CLUTCH HIGH
TEMPERATURE WARNING
PARKING BRAKE RELEASE WARNING
This will appear if the transmission oil temperature becomes unusually high.
“Transmission warning light” page 2-30)
(
This will appear if the transmission clutch
temperature becomes unusually high.
“Transmission warning light” page 2-30)
(
This will appear if the vehicle speed is above 4
MPH (7 km/h) with the parking brake applied.
(
“Brake warning light” page 2-26)
(
“Parking brake reminder chime” page 233)
2-36 Instruments and controls
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(135,1)
LOW BRAKE FLUID WARNING
This will appear if the brake fluid level becomes
low. (
“Brake warning light” page 2-26)
ANTI-LOCK BRAKING SYSTEM
(ABS) WARNING
VEHICLE DYNAMIC CONTROL (VDC)
SYSTEM WARNING
This will appear if the Anti-lock Braking System
(ABS) is not functioning properly. (
“Antilock Braking System (ABS) warning light” page
2-26) (
“Brake warning light” page 2-26)
This will appear if the Vehicle Dynamic Control
(VDC) system or the hill start assist system is
not functioning properly. (
“Vehicle Dynamic
Control (VDC) warning light” page 2-31)
(
“Vehicle Dynamic Control (VDC) off indicator light” page 2-32)
Instruments and controls 2-37
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(136,1)
damage to the AWD system.
AWD CLUTCH HIGH TEMPERATURE
WARNING
FRONT/REAR TIRE SIZE DISCREPANCY WARNING
This will appear if the temperature of the AWD
clutch becomes unusually high. (
“AllWheel Drive (AWD) warning light” page 2-25)
This will appear if the diameter of the front and
the rear wheels are different. (
“All-Wheel
Drive (AWD) warning light” page 2-25)
NOTE:
If the vehicle is driven in a way which
causes the rear wheels to slip, the AWD
clutch temperature will increase and the
warning indicator may flash. Continuing to
drive in a way that causes the warning light
to flash may cause the clutch to reach
excessive temperatures that could result in
2-38 Instruments and controls
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(137,1)
AWD SYSTEM WARNING
LOW TIRE PRESSURE WARNING
RUN-FLAT TIRE WARNING
This will appear if the AWD system is not
functioning properly while the engine is running.
(
“All-Wheel Drive (AWD) warning light”
page 2-25)
This will appear if the vehicle is being driven with
low tire pressure. (
“Low tire pressure
warning light” page 2-27)
This will appear and a chime will sound if the
vehicle is being driven with one or more flat tires.
(
“Low tire pressure warning light” page 227)
Instruments and controls 2-39
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(138,1)
TIRE PRESSURE MONITORING
SYSTEM (TPMS) WARNING
CRUISE CONTROL SYSTEM WARNING
This will appear if the Tire Pressure Monitoring
System (TPMS) is not functioning properly.
(
“Low tire pressure warning light” page
2-27)
This will appear if the cruise control system is
not functioning properly. (
“Cruise set
switch indicator light” page 2-31)
LOW FUEL WARNING
This will appear when the fuel level in the tank is
getting low. Refuel as soon as it is convenient,
preferably before the fuel gauge reaches the
empty (E) position.
This displays the approximate distance that the
vehicle can be driven based on the amount of
fuel remaining in the fuel tank and the actual fuel
consumption.
NOTE:
. The low fuel warning will appear when
the amount of fuel remaining in the
tank decreases to approximately 3 US
gallons (12 liters).
2-40 Instruments and controls
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(139,1)
.
The timing of the low fuel warning
display may change depending on
braking, turning, acceleration, or going
up or down hills.
.
If the vehicle is not refueled after the
low fuel warning appears, the display
will change to “
”. This change
timing may become earlier depending
on the driving conditions. This does not
indicate that there is a malfunction.
DOOR/TRUNK OPEN WARNING
HEADLIGHT SYSTEM WARNING
This will appear if any of the doors and/or trunk
lid are open or not closed securely. The vehicle
icon indicates which door or the trunk lid is
open.
This will appear if the LED headlight system is
not functioning properly. Have the system
checked by a GT-R certified NISSAN dealer.
Instruments and controls 2-41
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(140,1)
system. You cannot start the engine with an
unregistered Intelligent Key.
(
“Intelligent Key system” page 3-8)
LOW WASHER FLUID WARNING
NO KEY WARNING
This will appear when the washer tank fluid is at
a low level. Add washer fluid as necessary.
(
“Window washer fluid” page 8-16)
This will appear in either of the following
conditions.
No key inside the vehicle
The warning appears when the door is closed
with the Intelligent Key left outside the vehicle
and the ignition switch in the ACC or ON
position. Make sure that the Intelligent Key is
inside the vehicle.
Unregistered Intelligent Key
The warning appears when the ignition switch is
pushed from the LOCK position and the
Intelligent Key cannot be recognized by the
2-42 Instruments and controls
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(141,1)
OPERATION DISPLAYS
These displays appear when an appropriate
operation is required in starting or stopping the
engine.
ENGINE START OPERATION INDICATOR
This indicator appears when the shift lever is in
P position.
the &
This indicator means that the engine will start by
pushing the ignition switch with the brake pedal
depressed.
SHIFT “P” WARNING
This warning appears and an inside warning
chime sounds when the ignition switch is
pushed to stop the engine with the shift lever
P position.
in any position except the &
If this warning appears, move the shift lever to
P position. This warning will also turn off
the &
when pushing the ignition switch to the ON
position.
Instruments and controls 2-43
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(142,1)
“PUSH” WARNING
This warning appears when the shift lever is
P position with the ignition switch
moved to the &
P warning
in the ACC position after the SHIFT &
appears.
If this warning appears, push the ignition switch
to the OFF position.
STEERING LOCK RELEASE MALFUNCTION INDICATOR
INTELLIGENT KEY INSERTION INDICATOR
This indicator appears when the steering wheel
lock cannot be released from the LOCK position. If this indicator appears, push the ignition
switch while lightly turning the steering wheel
right and left.
This indicator appears when the Intelligent Key
needs to be inserted into the Intelligent Key port
(for example, the Intelligent Key battery is
discharged).
If this indicator appears, insert the Intelligent Key
into the Intelligent Key port in the correct
direction. (
“Intelligent Key battery discharge” page 5-12)
2-44 Instruments and controls
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(143,1)
SECURITY SYSTEMS
INTELLIGENT KEY REMOVAL INDICATOR
INTELLIGENT KEY BATTERY DISCHARGE INDICATOR
Your vehicle has two types of security systems,
as follows:
This indicator appears when the driver’s door is
opened with the ignition switch in the OFF or
LOCK position and the Intelligent Key placed in
the Intelligent Key port. A key reminder chime
also sounds.
If this indicator appears, remove the Intelligent
Key from the Intelligent Key port and take it with
you when leaving the vehicle.
This indicator appears when the Intelligent Key
battery is running out of power.
If this indicator appears, replace the battery with
a new one. (
“Intelligent Key battery replacement” page 8-27)
.
Vehicle security system
. NISSAN Vehicle Immobilizer System
The security condition will be shown by the
security indicator light.
VEHICLE SECURITY SYSTEM
The vehicle security system provides visual and
audio alarm signals if someone opens the doors,
hood, or trunk lid when the system is armed. It is
not, however, a motion detection type system
that activates when a vehicle is moved or when a
vibration occurs.
Instruments and controls 2-45
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(144,1)
The system helps deter vehicle theft but cannot
prevent it, nor can it prevent the theft of interior
or exterior vehicle components in all situations.
Always secure your vehicle even if parking for a
brief period. Never leave your Intelligent Key(s)
in the vehicle, and always lock it when unattended. Be aware of your surroundings, and
park in secure, well-lit areas whenever possible.
Many devices offering additional protection,
such as component locks, identification markers,
and tracking systems, are available at auto
supply stores and specialty shops. Your GT-R
certified NISSAN dealer may also offer such
equipment. Check with your insurance company
to see if you may be eligible for discounts for
various theft protection features.
How to arm the vehicle security
system
1. Close all windows.
The system can be armed even if the
windows are open.
2. Push the ignition switch to the OFF or LOCK
position.
3. Remove the Intelligent Key from the vehicle.
4. Close all doors, hood and trunk. Lock all
doors. The doors can be locked with the
Intelligent Key, door handle request switch
or power door lock switch. The power door
lock switch should be operated while the
door is open, and then closed.
5. Confirm that the security indicator light
comes on. The security indicator light stays
on for about 30 seconds. The vehicle
security system is now pre-armed. After
about 30 seconds the vehicle security
system automatically shifts into the armed
phase. The security light begins to flash
once every approximately 3 seconds. If,
during this 30-second pre-arm time period,
the door is unlocked, or the ignition switch is
pushed to ACC or ON, the system will not
arm.
Even when the driver and/or passengers
are in the vehicle, the system will activate
with all doors, hood, and trunk lid locked
with the ignition switch in the LOCK
position. When pushing the ignition switch
to the ACC or ON position, the system will
be released.
Vehicle security system activation
The vehicle security system will give the following alarm:
.
The headlights blink and the horn sounds
intermittently.
.
The alarm automatically turns off after
approximately 1 minute. However, the alarm
reactivates if the vehicle is tampered with
again.
2-46 Instruments and controls
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(145,1)
The alarm is activated by:
.
Opening the door or the trunk lid without
using the button on the Intelligent Key, the
door handle request switch or the mechanical key. (Even if the door is opened by
releasing the door inside lock knob, the
alarm will activate.)
.
Opening the hood.
How to stop an activated alarm
The alarm will stop by:
.
Unlocking a door by pushing the UNLOCK
button on the Intelligent Key.
.
Unlocking a door by pushing the door
handle request switch.
.
Pushing the ignition switch to the ACC or
ON position.
If the system does not operate as described above, have it checked by a GT-R
certified NISSAN dealer.
NISSAN VEHICLE IMMOBILIZER
SYSTEM
The NISSAN Vehicle Immobilizer System will not
allow the engine to start without the use of the
registered Intelligent Key. Never leave these
keys in the vehicle.
FCC Notice:
For USA:
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Note: Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s
authority to operate the equipment.
For Canada:
This device complies with Industry Canada
licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must
accept any interference, including interference that may cause undesired operation
of the device.
Security indicator light
The security indicator light is located on the
instrument panel. It indicates the status of the
NISSAN Vehicle Immobilizer System.
The light blinks whenever the ignition switch is in
the ACC, OFF or LOCK position. This function
indicates the security systems equipped on the
vehicle are operational.
If the NISSAN Vehicle Immobilizer System is
malfunctioning, this light will remain on while the
ignition switch is in the ON position.
If the light still remains on and/or the
engine will not start, see a GT-R certified
NISSAN dealer for NISSAN Vehicle ImmoInstruments and controls 2-47
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(146,1)
WIPER AND WASHER SWITCH
bilizer System service as soon as possible.
Please bring all Intelligent Keys that you
have when visiting a GT-R certified
NISSAN dealer for service.
WARNING
In freezing temperatures the washer
solution may freeze on the windshield
and obscure your vision which may lead
to an accident. Warm windshield with
the defroster before you wash the
windshield.
window washer reservoir tank to
mix the washer fluid concentrate
and water.
The windshield wiper and washer operates
when the ignition switch is in the ON position.
NOTICE
.
Do not operate the washer continuously for more than 30 seconds.
.
Do not operate the washer if the
reservoir tank is empty.
.
Do not fill the window washer
reservoir tank with washer fluid
concentrates at full strength. Some
methyl alcohol based washer fluid
concentrates may permanently stain
the grille if spilled while filling the
window washer reservoir tank.
.
Pre-mix washer fluid concentrates
with water to the manufacturer’s
recommended levels before pouring
the fluid into the window washer
reservoir tank. Do not use the
2-48 Instruments and controls
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(147,1)
NOTE:
. In the MIST position, the wipers operate while the lever is lifted up. When
the lever is released, it automatically
returns to the OFF position and the
wipers stop.
USING THE WIPERS
Push the lever down to operate the wiper at the
following speed:
1
*
2
*
3
*
INT (Intermittent) — intermittent operation can
be adjusted by turning the knob toward A
(Slower) or B (Faster).
Low — continuous low speed operation
High — continuous high speed operation
*
*
4
Push the lever up *
to have one sweep
operation of the wiper.
.
When the speed sensing wiper interval
function is turned on, the intermittent
operation speed varies in accordance
with the vehicle speed. (For example,
when the vehicle speed is high, the
intermittent operation speed will be
faster.) To turn this function on and
off, see the separate Multi Function
Display Owner’s Manual.
.
If the wiper operation is interrupted by
snow or ice, the wiper may stop moving
to protect its motor. If this occurs, turn
the wiper switch to the OFF position
and remove the snow or ice on and
around the wiper arms. In approximately 1 minute, turn the switch on
again to operate the wiper.
USING THE WASHER
Pull the lever toward you to operate the washer.
Then the wiper will also operate several times.
NOTE:
When the level of washer fluid is low, a
warning display appears on the vehicle
information display. (
“Low washer
fluid warning” page 2-42)
Instruments and controls 2-49
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(148,1)
REAR WINDOW DEFROSTER
SWITCH
HEADLIGHT AND TURN SIGNAL
SWITCH
NOTICE
When cleaning the inner side of the rear
window, be careful not to scratch or
damage the rear window defroster.
To defog/defrost the rear window, start the
engine and push the switch on. The indicator
light on the switch will come on. Push the switch
again to turn the defroster off.
It will automatically turn off in approximately 15
minutes.
NOTE:
When the rear window defroster switch is
pressed, the heated outside mirrors also
operate at the same time. (
“Outside
mirrors” page 3-27)
HEADLIGHT SWITCH
Lighting
The parking, tail and license plate lights will turn
on after the engine is started regardless of the
position of the headlight switch. The lights will
turn off when the engine is turned off.
The daytime running lights will also turn on when
the engine is started.
Turning the switch to the
position:
The parking, side marker, tail, license plate and
instrument lights will come on and the daytime
running light will remain on.
2-50 Instruments and controls
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(149,1)
If the ignition switch is pushed to the OFF
position and one of the doors is opened, the
headlights remain on for 45 seconds.
Turning the switch to the
position:
Headlights will come on and all the other lights
remain on. The daytime running light will turn off.
Autolight system
The autolight system allows the headlights to be
set so they turn on and off automatically.
To set the autolight system:
1. Make sure the headlight switch is in the
1 .
AUTO position *
2. Push the ignition switch to the ON position.
3. The autolight system automatically turns the
headlights on and off.
To turn the autolight system off, turn the switch
to the OFF,
or
position.
The autolight system can turn on the headlights
automatically when it is dark and turn off the
headlights when it is light.
Instruments and controls 2-51
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(150,1)
NOTICE
CAUTION
Use low beams when there are cars
approaching from the opposite direction, during city driving and at similar
times.
.
When you turn on the headlight
switch again after the lights automatically turn off, the lights will not
turn off automatically. Be sure to
turn the light switch to the OFF
position when you leave the vehicle
for extended periods of time, otherwise the battery will be discharged.
.
Never leave the light switch on
when the engine is not running for
extended periods of time even if the
headlights turn off automatically.
Battery saver system
Headlight beam select
When the headlights are on, push the lever to
1 to switch to the high
the front of the vehicle *
beams. The high-beam indicator light illuminates. (
“High beam indicator light” page 231)
2
Pull the lever to the neutral position *
to
switch to the low beams.
3 will flash the
Pulling the lever toward you *
headlight high beam even when the headlight
switch is in the OFF position.
A chime will sound when the driver side door is
opened with the light switch in the
or
position and the ignition switch in the ACC,
OFF or LOCK position. (
“Light reminder
chime” page 2-32)
When the headlight switch is in the
or
position while the ignition switch is in the ON
position, the lights will automatically turn off after
a period of time when the ignition switch has
been pushed to the OFF position.
When the headlight switch remains in the
or
position after the lights automatically turn
off, the lights will turn on when the ignition
switch is pushed to the ON position.
Daytime running light system
The daytime running lights automatically illuminate when the engine is started with the parking
brake released. The daytime running lights
operate with the headlight switch in the OFF
position. Turn the headlight switch to the
position for full illumination when driving at night.
If the parking brake is applied before the engine
is started, the daytime running lights do not
illuminate. The daytime running lights illuminate
once the parking brake is released. The daytime
running lights will remain on until the ignition
switch is pushed to the OFF position.
2-52 Instruments and controls
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(151,1)
latch, and release the lever. The turn signal
will automatically flash three times.
Choose the appropriate method to signal a lane
change based on road and traffic conditions.
WARNING
When the daytime running light system
is active, tail lights on your vehicle are
not on. It is necessary at dusk to turn on
your headlights. Failure to do so could
cause an accident injuring yourself and
others.
TURN SIGNAL SWITCH
1 Turn signal
*
Move the lever up or down to signal the turning
direction. When the turn is completed, the turn
signals cancel automatically.
2 Lane change signal
*
.
Move the lever up or down until the turn
signal begins to flash, but the lever does not
latch, to signal a lane change. Hold the lever
until the lane change is completed.
.
Move the lever up or down until the turn
signal begins to flash, but the lever does not
Instruments and controls 2-53
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(152,1)
HORN
HEATED SEATS
TURNING OFF THE HEATERS
Move the switch to the level position. The switch
indicator turns off.
WARNING
Do not use or allow occupants to use
the seat heater if you or the occupants
cannot monitor elevated seat temperatures or have an inability to feel pain in
those body parts in contact with the
seat. Use of the seat heater by such
people could result in serious injury.
To sound the horn, push the center pad area of
the steering wheel.
WARNING
Do not disassemble the horn. Doing so
could affect proper operation of the
supplemental front air bag system.
Tampering with the supplemental front
air bag system may result in serious
personal injury.
The seat heaters can be used when the ignition
switch is in the ON position. The front seats are
warmed by the built-in heaters.
TURNING ON THE HEATERS
CAUTION
.
Do not put anything on the seat
which insulates heat, such as a
blanket, cushion, seat cover, etc.
Otherwise, the seat may become
overheated.
.
Do not place anything hard or heavy
on the seat or pierce it with a pin or
similar object. This may result in
damage to the heater.
.
Any liquid spilled on the heated seat
should be removed immediately
Push the "HI" or "LO" side of the switch to
activate the heaters. The switch indicator
illuminates.
Switch position
Function
HI
To heat the seat quickly
LO
To keep the seat warm
2-54 Instruments and controls
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(153,1)
POWER OUTLETS
with a dry cloth.
.
If any malfunctions are found or the
heated seat does not operate, turn
the switch off and have the system
checked by a GT-R certified NISSAN
dealer.
CAUTION
.
The outlet and plug may be hot
during or immediately after use.
.
Do not use with accessories that
exceed a 12 volt, 120W (10A) power
draw. Do not use double adapters or
more than one electrical accessory.
.
This power outlet is not designed
for use with a cigarette lighter unit.
.
Before inserting or disconnecting a
plug, be sure the electrical accessory being used is turned OFF.
.
When not in use, be sure to close
the cap. Do not allow water to
contact the outlet.
NOTICE
.
.
.
The battery could run down if the
seat heater is operated while the
engine is not running.
Do not use the seat heater for
extended periods or when no one
is using the seat.
When cleaning the seat, never use
gasoline, thinner, or any similar
materials.
.
Push the plug in as far as it will go.
If good contact is not made, the plug
may overheat or the internal temperature fuse may open.
NOTICE
.
Use power outlet with the engine
running to avoid discharging the
vehicle battery.
.
Avoid using power outlet when the
air conditioner, headlights or rear
window defroster is on.
Instruments and controls 2-55
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(154,1)
STORAGE
Next to the steering wheel
Pull out the cap to use the outlet.
Replace the cap after use.
Inside the console box (except for NISMO models)
Open the cap to use the outlet.
Close the cap after use.
CUP HOLDERS
CAUTION
.
Avoid abrupt starting and braking
when the cup holder is being used
to prevent spilling the drink. If the
liquid is hot, it can scald you or your
passenger.
.
Use only soft cups in the cup holder.
Hard objects can injure you in an
accident.
2-56 Instruments and controls
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(155,1)
Front
Slide the cover toward the rear of the vehicle to
open.
To close, slide the cover back toward the front of
the vehicle.
Rear
NOTE:
A
is wider and shallower
Cup holder *
B
C . Small-size
than cup holders *
and *
cups are likely to tip over in cup holder
A . Use cup holders *
B and *
C .
*
SUNGLASSES HOLDER
WARNING
Keep the sunglasses holder closed
while driving to prevent an accident.
To open the sunglasses holder, push
1 .
*
Instruments and controls 2-57
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(156,1)
CAUTION
Do not use for anything other than
glasses.
NOTICE
Do not leave glasses in the sunglasses
holder while parking in direct sunlight.
The heat may damage the glasses.
DOOR POCKET
Door pockets are located inside the driver’s side
and passenger’s side doors.
NOTICE
Do not grasp the door pockets to open
and close the doors. Doing so may
damage the pockets.
GLOVE BOX
WARNING
Keep glove box lid closed while driving
to help prevent injury in an accident or a
sudden stop.
Pull the knob toward you to open the glove box.
To close the glove box, press the lid forward until
it locks in place.
2-58 Instruments and controls
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(157,1)
1 and unlock
Use the mechanical key to lock *
2 the glove box. (
“Mechanical key” page
*
3-3)
The mechanical key stops when it is inserted
approximately halfway in.
CONSOLE BOX
COAT HOOKS
1 to open the lid.
Lift up the lock knob *
To close the center console box, press on the lid
until it locks in place.
To use the coat hook, push the upper side of the
hook to release it.
NOTE:
The console box contains a power outlet
(except for NISMO models) or a USB
(Universal Serial Bus) connection port (for
NISMO models). This USB connection port
is reserved for future use for features that
have yet to be developed. Do not use for
unapproved USB devices.
CAUTION
Do not hang any objects with sharp
edges on the coat hangers. These items
may be knocked off if the SRS air bag
deploys, possibly causing injury.
Instruments and controls 2-59
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(158,1)
WINDOWS
NOTICE
POWER WINDOWS
Do not place items that are more than 2
lb (1 kg) on the hook.
WARNING
.
Make sure that all passengers have
their hands, etc. inside the vehicle
while it is in motion and before
closing the windows. Use the window lock switch to prevent unexpected use of the power windows.
.
Do not leave children unattended
inside the vehicle. They could unknowingly activate switches or controls and become trapped in the
window. Unattended children could
become involved in serious accidents.
Driver’s side
1.
2.
3.
Window lock button
Driver’s window switch
Front passenger’s window switch
The power windows operate when the ignition
switch is in the ON position or for about 45
seconds after the ignition switch is pushed to
the LOCK position. If the driver’s or front
passenger’s door is opened during this period
of about 45 seconds, power to the windows is
canceled.
2-60 Instruments and controls
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(159,1)
Passenger’s side power window
switch
The passenger side switch will open or close
only the corresponding window. To open close
the window, push down or pull up the switch
and hold it.
Automatic operation
Front passenger’s side
4.
Front passenger’s window switch
Main power window switch (driver’s
side)
To open or close the window, push down or pull
up the switch and hold it. The main switch
(driver’s side switches) will open or close all the
windows.
Locking passengers’ windows
When the window lock button is pushed in, only
the driver’s side window can be opened or
closed. Push it in again to cancel.
To fully open or close the window, completely
push down or pull up the switch and release it; it
does not need to be held. The window will
automatically open or close all the way. To stop
the window, just push or lift the switch in the
opposite direction.
A light push or pull on the switch will cause the
window to open or close until the switch is
released.
Auto reverse function
If the control unit detects something caught in
the window as it is closing, the window will be
immediately lowered.
The auto reverse function can be activated when
the window is closed by automatic operation
when the ignition switch is in the ON position or
for 45 seconds after the ignition switch is
pushed to the OFF position.
Depending on the environment or driving conditions, the auto reverse function may be
activated if an impact or load similar to something being caught in the window occurs.
WARNING
There are some small distances immediately before the closed position which
cannot be detected. Make sure that all
passengers have their hands, etc., inside the vehicle before closing the
window.
Automatic adjusting function
CAUTION
When the battery cable is removed from
the battery terminal, do not close either
of the front doors. The automatic window adjusting function will not work
and the side roof panel may be damaged.
The power window has an automatic adjusting
function. When the door is being opened, the
window is automatically lowered slightly to avoid
contact between the window and the side roof
panel. When the door is closed, the window is
Instruments and controls 2-61
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(160,1)
INTERIOR LIGHTS
automatically raised slightly.
While the automatic adjusting function does not
work, the window will be controlled as follows:
.
When the door is opened, the window
lowers for approximately 2 seconds.
.
While the door is open, the window cannot
be raised.
If the power window automatic function does
not operate properly after performing the procedure above, have your vehicle checked by a
GT-R certified NISSAN dealer.
If the windows do not close automatically
If the power window automatic function (closing
only) does not operate properly, perform the
following procedure to initialize the power
window system.
1. Push the ignition switch to the ON position.
2. Close the door.
3. Open the window completely by operating
the power window switch.
4. Pull the power window switch and hold it to
close the driver side window, and then hold
the switch more than 3 seconds after the
window is closed completely.
5. Release the power window switch. Operate
the window by the automatic function to
confirm the initialization is complete.
6. Perform steps 2 through 5 above for the
passenger side window by operating either
driver’s or passenger’s side switch.
MAP LIGHTS
Push the button as illustrated to turn the light on
or off.
2-62 Instruments and controls
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(161,1)
NOTE:
The lights will also turn off after a period of
time when the lights remain illuminated
after the ignition switch has been pushed
to the OFF or LOCK position to prevent the
battery from becoming discharged.
DOOR position
2 ,
When the switch is in the DOOR position *
the map lights will turn on when the door is
opened and turn off when the door is closed.
The map lights will turn off approximately 15
seconds after the door is closed with the ignition
switch in the OFF or LOCK position.
INTERIOR LIGHT CONTROL SWITCH
NOTE:
The interior light control switch has three
1 , DOOR *
2 and OFF *
3 .
positions: ON *
When the interior light control switch is in
the DOOR position and the door is open,
the light will remain on even when the map
light switch is pressed to turn off.
Key-linked interior light control system:
The map lights will turn on and off linked with the
locking and unlocking of the door.
This function operates when the interior light
control switch is in the DOOR position.
ON position
When the switch is in the ON position
map lights will illuminate.
1 , the
*
NOTICE
Do not use the light for extended
periods of time with the engine
stopped. This could result in a discharged battery.
seconds, then it turns off.
While the map light is on, if the ignition switch is
pushed to the ACC or ON position, or if the
driver’s side door is locked, the light turns off.
. When exiting the vehicle
When the ignition switch is pushed to the OFF
or LOCK position, the map lights turn on for
approximately 15 seconds, then it turns off.
If the driver’s side door is locked while the map
lights are on, the light turns off.
NOTE:
It is possible to cancel the key-linked
interior light control system setting. See
the separate Multi Function Display Owner’s Manual.
OFF position
3 , the
When the switch is in the OFF position *
map lights will not illuminate, regardless of any
condition.
. When entering the vehicle
When the driver’s seat door is unlocked, the
map light illuminates for approximately 15
Instruments and controls 2-63
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(162,1)
VANITY MIRROR LIGHTS
HomeLink® UNIVERSAL
TRANSCEIVER
The HomeLink® Universal Transceiver provides a
convenient way to consolidate the functions of
up to three individual hand-held transmitters into
one built-in device.
HomeLink® Universal Transceiver:
.
WARNING
.
Do not use the HomeLink® Universal
Transceiver with any garage door
opener that lacks safety stop and
reverse features as required by
federal safety standards. (These
standards became effective for
opener models manufactured after
April 1, 1982.) A garage door opener
which cannot detect an object in the
path of a closing garage door and
then automatically stop and reverse,
does not meet current federal safety
standards. Using a garage door
opener without these features increases the risk of serious injury or
death.
.
During the programming procedure
your garage door or security gate
will open and close (if the transmitter is within range). Make sure that
people or objects are clear of the
garage door, gate, etc. that you are
programming.
.
Your vehicle’s engine should be
turned off while programming the
HomeLink® Universal Transceiver.
Will operate most Radio Frequency (RF)
devices such as garage doors, gates, home
and office lighting, entry door locks and
security systems.
.
There is an illuminated vanity mirror on the
reverse side of the sun visor.
Is powered by your vehicle’s battery. No
separate batteries are required. If the
vehicle’s battery is discharged or is disconnected, HomeLink® will retain all programming.
When the HomeLink® Universal Transceiver is programmed, retain the original
transmitter for future programming procedures (Example: new vehicle purchases).
Upon sale of the vehicle, the programmed
HomeLink® Universal Transceiver buttons
should be erased for security purposes.
For additional information, refer to
“Programming HomeLink®” page 265.
2-64 Instruments and controls
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(163,1)
Do not breathe exhaust gases; they
contain colorless and odorless carbon monoxide. Carbon monoxide is
dangerous. It can cause unconsciousness or death.
PROGRAMMING HomeLink®
If you have any questions or are having difficulty
programming your HomeLink® buttons, refer to
the HomeLink® web site at: www.homelink.com
or call 1-800-355-3515.
NOTE:
It is also recommended that a new battery
be placed in the hand-held transmitter of
the device being programmed to
HomeLink® for quicker programming and
accurate transmission of the radio-frequency.
1. Position the end of your hand-held transmitter 1-3 in (26-76 mm) away from the
HomeLink® surface, keeping the HomeLink®
1 in view.
indicator light *
2. Using both hands, simultaneously press and
hold the desired HomeLink® button and
handheld transmitter button. DO NOT re1
lease until the HomeLink® indicator light *
flashes slowly and then rapidly. When the
indicator light flashes rapidly, both buttons
may be released. (The rapid flashing indicates successful programming.)
NOTE:
Some devices to be programmed may
require you to replace Step 2 with the
cycling procedure noted in the
“Programming HomeLink® for Canadian customers and gate openers”
page 2-66.
3. Press and hold the programmed HomeLink®
button and observe the indicator light.
. If the indicator light *
1 is solid/continuous, programming is complete and your
device should activate when the
HomeLink® button is pressed and released.
. If the indicator light *
1 blinks rapidly for
two seconds and then turns to a solid/
continuous light, continue with Steps 4-6
for a rolling code device. A second
person may make the following steps
easier. Use a ladder or other device. Do
not stand on your vehicle to perform the
next steps.
Instruments and controls 2-65
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(164,1)
4. At the receiver located on the garage door
opener motor in the garage, locate the
“learn” or “smart” button (the name and
color of the button may vary by manufacturer
but it is usually located near where the
hanging antenna wire is attached to the
unit). If there is difficulty locating the button,
reference the garage door opener’s manual.
5. Press and release the “learn” or “smart”
button.
NOTE:
Once the button is pressed, you have
approximately 30 seconds to initiate
the next step.
6. Return to the vehicle and firmly press and
hold the programmed HomeLink® button for
two seconds and release. Repeat the
“press/hold/release” sequence up to 3
times to complete the programming process. HomeLink® should now activate your
rolling code equipped device.
7. If you have any questions or are having
difficulty programming your HomeLink® buttons, refer to the HomeLink® web site at:
www.homelink.com or call 1-800-3553515.
PROGRAMMING HomeLink® FOR
CANADIAN CUSTOMERS AND GATE
OPENERS
Canadian radio-frequency laws require transmitter signals to “time-out” (or quit) after several
seconds of transmission – which may not be
long enough for HomeLink® to pick up the signal
during programming. Similar to this Canadian
law, some U.S. gate operators are designed to
“time-out” in the same manner.
If you live in Canada or you are having difficulties
programming a gate operator or garage door
opener by using the “Programming HomeLink®”
procedures, replace “Programming HomeLink®”
Step 2 with the following:
NOTE:
When programming a garage door opener,
etc., unplug the device during the “cycling”
process to prevent possible damage to the
garage door opener components.
Step 2: Using both hands, simultaneously press
and hold the desired HomeLink® button and the
hand-held transmitter button. During programming, your hand-held transmitter may automatically stop transmitting. Continue to press and
hold the desired HomeLink® button while you
press and re-press (“cycle”) your hand-held
transmitter every two seconds until the fre-
quency signal has been learned. The HomeLink®
indicator light will flash slowly and then rapidly
after several seconds upon successful programming. DO NOT release until the HomeLink®
indicator light flashes slowly and then rapidly.
When the indicator light flashes rapidly, both
buttons may be released. The rapid flashing
indicates successful programming.
Proceed with “Programming HomeLink®” step 3
to complete.
Remember to plug the device back in when
programming is completed.
OPERATING THE HomeLink® UNIVERSAL TRANSCEIVER
The HomeLink® Universal Transceiver, after it is
programmed, can be used to activate the
programmed device. To operate, simply press
and release the appropriate programmed
HomeLink® Universal Transceiver button. The
amber indicator light will illuminate while the
signal is being transmitted.
For convenience, the hand-held transmitter of
the device may also be used at any time.
2-66 Instruments and controls
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(165,1)
PROGRAMMING TROUBLESHOOTING
CLEARING THE PROGRAMMED INFORMATION
If the HomeLink® does not quickly learn the
hand-held transmitter information:
The following procedure clears the programmed
information from both buttons. Individual buttons
cannot be cleared. However, individual buttons
can be reprogrammed, see
“Reprogramming a single HomeLink® button” page 2-67.
.
replace the hand-held transmitter batteries
with new batteries.
.
position the hand-held transmitter with its
battery area facing away from the
HomeLink® surface.
.
press and hold both the HomeLink® and
hand-held transmitter buttons without interruption.
.
position the hand-held transmitter 1-3 in
(26-76 mm) away from the HomeLink®
surface. Hold the transmitter in that position
for up to 15 seconds. If HomeLink® is not
programmed within that time, try holding the
transmitter in another position - keeping the
indicator light in view at all times.
If you have any questions or are having difficulty
programming your HomeLink® buttons, refer to
the HomeLink® web site at: www.homelink.com
or 1-800-355-3515.
To clear all programming
1. Press and hold the two outer HomeLink®
buttons until the indicator light begins to
flash in approximately 10 seconds. Do not
hold for longer than 20 seconds.
2. Release both buttons.
HomeLink® is now in the programming mode
and can be programmed at any time beginning
with “Programming HomeLink®” - Step 1.
REPROGRAMMING A SINGLE
HomeLink® BUTTON
HomeLink®” - Step 1.
For questions or comments, contact HomeLink®
at: www.homelink.com or 1-800-355-3515.
The HomeLink® Universal Transceiver button
has now been reprogrammed. The new device
can be activated by pushing the HomeLink®
button that was just programmed. This procedure will not affect any other programmed
HomeLink® buttons.
IF YOUR VEHICLE IS STOLEN
If your vehicle is stolen, you should change the
codes of any non-rolling code device that has
been programmed into HomeLink®. Consult the
Owner’s Manual of each device or call the
manufacturer or retailer of those devices for
additional information.
When your vehicle is recovered, you will
need to reprogram the HomeLink® Universal Transceiver with your new transmitter
information.
To reprogram a HomeLink® Universal Transceiver button, complete the following.
FCC Notice:
1. Press and hold the desired HomeLink®
button. Do not release the button.
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any interfer-
2. The indicator light will begin to flash after 20
seconds. Without releasing the HomeLink®
button, proceed with “Programming
For USA:
Instruments and controls 2-67
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(166,1)
ence received, including interference that
may cause undesired operation.
NOTE:
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s authority
to operate the equipment.
For Canada:
This device complies with Industry Canada
licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must
accept any interference, including interference that may cause undesired operation
of the device.
2-68 Instruments and controls
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(167,1)
3 Pre-driving checks and adjustments
Keys ............................................................................................. 3-2
Intelligent Key ...................................................................... 3-2
Doors ........................................................................................... 3-4
Locking with inside lock knob ........................................ 3-5
Locking with power door lock switch ........................... 3-5
Automatic door lock system ............................................ 3-5
Locking with mechanical key ........................................... 3-6
Opening the doors ............................................................ 3-7
Intelligent Key system ............................................................. 3-8
Intelligent Key functions .................................................... 3-9
Remote keyless entry system ....................................... 3-12
Setting hazard indicator and horn mode .................. 3-13
Warning signals ............................................................... 3-15
Troubleshooting guide ................................................... 3-16
Hood ......................................................................................... 3-17
Opening the hood ........................................................... 3-17
Closing the hood ............................................................. 3-18
Trunk ........................................................................................
Trunk open request switch .........................................
Trunk lid release switch ...............................................
Trunk release power cancel switch ..........................
Opening and closing the trunk ..................................
Emergency trunk lid release .......................................
Fuel-filler door .......................................................................
Opening the fuel-filler door ........................................
Closing the fuel-filler door ..........................................
Steering wheel ......................................................................
Tilt/telescopic steering column ..................................
Sun visors ...............................................................................
Mirrors .....................................................................................
Inside mirror ....................................................................
Outside mirrors ..............................................................
Vanity mirror ....................................................................
[ Edit: 2014/ 12/ 8
3-19
3-19
3-19
3-20
3-21
3-21
3-23
3-24
3-24
3-25
3-25
3-26
3-26
3-26
3-27
3-28
Model: R35-D ]
(168,1)
KEYS
process requires erasing all memory in the
Intelligent Key components when registering
new keys, be sure to take all Intelligent Keys
that you have to a GT-R certified NISSAN
dealer.
A key number plate is supplied with your keys.
Record the key number and keep it in a safe
place (such as your wallet), not in the vehicle. If
you lose your keys, see a GT-R certified
NISSAN dealer for duplicates by using the key
number. NISSAN does not record any key
numbers so it is very important to keep track of
your key number plate.
NOTICE
.
A key number is only necessary when you have
lost all keys and do not have one to duplicate
from. If you still have a key, this key can be
duplicated by a GT-R certified NISSAN dealer.
1.
2.
3.
Intelligent Key (2 sets)
Mechanical key (inside Intelligent Keys) (2 sets)
Key number plate (1 set)
INTELLIGENT KEY
Your vehicle can only be driven with the
Intelligent Keys which are registered to your
vehicle’s Intelligent Key system components and
NISSAN Vehicle Immobilizer System components. As many as 4 Intelligent Keys can be
registered and used with one vehicle. The new
keys must be registered by a GT-R certified
NISSAN dealer prior to use with the Intelligent
Key system and NISSAN Vehicle Immobilizer
System of your vehicle. Since the registration
3-2
Be sure to carry the Intelligent Key
with you when driving. The Intelligent Key is a precision device with a
built-in transmitter. To avoid damaging it, please note the following.
— The Intelligent Key is water
resistant; however, wetting may
damage the Intelligent Key. If
the Intelligent Key gets wet,
immediately wipe until it is completely dry.
— Do not bend, drop or strike it
against another object.
— Do not place the Intelligent Key
for an extended period in a
place where temperatures exceed 1408F (608C).
— If the outside temperature is
below 148F (−108C), the battery
of the Intelligent Key may not
Pre-driving checks and adjustments
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(169,1)
function properly.
CAUTION
— Do not change or modify the
Intelligent Key.
Always carry the mechanical key installed in the Intelligent Key.
— Do not use a magnet key holder.
— Do not place the Intelligent Key
near an electric appliance such
as a television set, personal
computer or cellular phone.
Valet hand-off
— Do not allow the Intelligent Key
to come into contact with water
or salt water, and do not wash it
in a washing machine. This
could affect the system function.
.
If an Intelligent Key is lost or stolen,
NISSAN recommends erasing the ID
code of that Intelligent Key. This will
prevent the Intelligent Key from
unauthorized use to unlock the
vehicle. For information regarding
the erasing procedure, please contact a GT-R certified NISSAN dealer.
Mechanical key
To remove the mechanical key, release the lock
knob at the back of the Intelligent Key.
To install the mechanical key, firmly insert it into
the Intelligent Key until the lock knob returns to
the lock position.
Use the mechanical key to lock or unlock the
doors and the glove box. (
“Locking with
mechanical key” page 3-6) (
“Glove box”
page 2-58)
When you have to leave a key with a valet, give
them the Intelligent Key itself and keep the
mechanical key with you to protect your
belongings.
To prevent the glove box and the trunk from
being opened during valet hand-off, follow the
procedures below.
1. Push the trunk release power cancel switch
to the OFF side. (
“Trunk release power
cancel switch” page 3-20)
2. Remove the mechanical key from the Intelligent Key.
3. Lock the glove box with the mechanical key.
(
“Glove box” page 2-58)
4. Hand the Intelligent Key to the valet, keeping
the mechanical key in your pocket or bag for
insertion into the Intelligent Key when you
retrieve your vehicle.
Pre-driving checks and adjustments 3-3
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(170,1)
DOORS
NOTICE
WARNING
.
Always have the doors locked while
driving. Along with the use of seat
belts, this provides greater safety in
the event of an accident by helping
to prevent persons from being
thrown from the vehicle. This also
helps keep children and others from
unintentionally opening the doors,
and will help keep out intruders.
.
Before opening any door, always
look for and avoid oncoming traffic.
.
Do not leave children unattended
inside the vehicle. They could unknowingly activate switches or controls. Unattended children could
become involved in serious accidents.
To prevent theft or accidents, be sure to
stop the engine and lock the doors
before stepping away from the vehicle.
3-4
“Automatic
When the battery cable is removed from
the battery terminal, do not close either
of the front doors. The automatic window adjusting function will not work,
and the side roof panel may be damaged. (
“Automatic adjusting
function” page 2-61)
NOTE:
. The doors of this vehicle are somewhat
harder to close than those of an
ordinary vehicle (especially when the
vehicle is new). This is because the
stiffness of the rubber has been increased to improve the airtightness of
the vehicle interior during situations
such as higher speed driving. This does
not indicate that there is a malfunction.
.
CAUTION
automatically raised slightly. (
adjusting function” page 2-61)
When the driver’s door is locked or
unlocked, the fuel-filler door is automatically locked or unlocked at the
same time.
When the door is being opened, the window is
automatically lowered slightly to avoid contact
between the window and the side roof panel.
When the door is closed, the window is
Pre-driving checks and adjustments
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(171,1)
NOTE:
When locking the door this way, be sure
not to leave the Intelligent Key inside the
vehicle.
To unlock the doors, push the power door lock
2 .
switch to the unlock position *
Lockout protection
LOCKING WITH INSIDE LOCK KNOB
To lock a door individually, push down the inside
1 then close the
lock knob to the lock position *
door.
To unlock, lift up the inside lock knob to the
2 .
unlock position *
NOTE:
When locking the door without an Intelligent Key, be sure not to leave the Intelligent Key inside the vehicle.
LOCKING WITH POWER DOOR
LOCK SWITCH
Operating the power door lock switch will lock
or unlock all the doors. The switches are located
on the driver’s and front passenger’s door
armrests.
To lock the doors, push the power door lock
1 with the driver’s
switch to the lock position *
or front passenger’s door open, then close the
door.
When the power door lock switch (driver or front
passenger) is moved to the lock position with
the Intelligent Key left in the key port and any
door open, all doors will lock and unlock
automatically.
When the power door lock switch (driver or front
passenger) is moved to the lock position with
the Intelligent Key left in the vehicle (not in the
Intelligent Key port) and any door open, all doors
will unlock automatically and a chime will sound
after the door is closed.
These functions help to prevent the Intelligent
Key from being accidentally locked inside the
vehicle.
AUTOMATIC DOOR LOCK SYSTEM
.
All doors lock automatically when the vehicle
speed reaches 15 MPH (24 km/h).
.
All doors unlock automatically when the
ignition switch is placed in the OFF position.
The automatic unlock function can be
Pre-driving checks and adjustments 3-5
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(172,1)
deactivated or activated. To deactivate or
activate the automatic door unlock system,
perform the following procedure:
1. Close all doors.
2. Place the ignition switch in the ON position.
3. Within 20 seconds of performing Step 2,
push and hold the power door lock switch to
the
position (UNLOCK) for more than 5
seconds.
4. When activated, the hazard indicator will
flash twice. When deactivated, the hazard
indicator will flash once.
5. The ignition switch must be placed in the
OFF and ON position again between each
setting change.
When the automatic door unlock system is
deactivated, the doors do not unlock when the
ignition switch is placed in the OFF position. To
unlock the door manually, use the inside lock
knob or the power door lock switch (driver’s or
front passenger’s side).
3-6
LOCKING WITH MECHANICAL KEY
The driver’s door will be locked or unlocked
using the mechanical key.
1. Press the rear end of the driver’s outside
1 to lift up the front end *
2 .
door handle *
2. With the outside door handle lifted up, use
the mechanical key and turn the key cylinder
A counterclockwise to remove.
cap *
Pre-driving checks and adjustments
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(173,1)
NOTE:
. Do not pull too hard on the door handle
when locking or unlocking the doors.
Pulling too hard will prevent the mechanical key from turning, making it
impossible to lock or unlock the doors.
.
3. Turning the door key cylinder to the front of
1 will lock the driver’s door,
the vehicle *
2 will
and turning to the rear of the vehicle *
unlock the driver’s door.
4. Replace the key cylinder cap in the reverse
order.
NOTICE
Unlocking the driver’s door using the
mechanical key will not unlock the fuelfiller door.
OPENING THE DOORS
Opening from outside the vehicle
1. Press the rear end of the outside door
1 to lift up the front end of the
handle *
handle.
2. Pull the front end of the outside door handle
2 toward you.
*
Do not drive with the cap removed.
Water that enters through the keyhole
may cause a malfunction.
Pre-driving checks and adjustments 3-7
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(174,1)
INTELLIGENT KEY SYSTEM
Opening from inside the vehicle
Lift up the inside door handle to open a door
from inside the vehicle.
.
NOTICE
Do not grasp the door pockets to open
and close the doors. Doing so may
damage the pockets.
.
Radio waves could adversely affect
electric medical equipment. Those
who use a pacemaker should contact the electric medical equipment
manufacturer for the possible influences before use.
The Intelligent Key transmits radio
waves when the buttons are
pushed. The Federal Aviation
Agency (FAA) advises the radio
waves may affect aircraft navigation
and communication systems. Do not
operate the Intelligent Key while on
an airplane. Make sure the buttons
are not operated unintentionally
when the unit is stored for a flight.
The Intelligent Key system can operate all the
door locks using the remote controller function
or pushing the request switch on the vehicle
without taking the key out from a pocket or
purse. The operating environment and/or conditions may affect the Intelligent Key system
operation.
Be sure to read the following before using the
Intelligent Key system.
3-8
CAUTION
WARNING
.
.
Be sure to carry the Intelligent Key
with you when operating the vehicle.
.
Never leave the Intelligent Key in
the vehicle when you leave the
vehicle.
The Intelligent Key is always communicating
with the vehicle as it receives radio waves.
The Intelligent Key system transmits weak
radio waves. Environmental conditions may
interfere with the operation of the Intelligent
Key system under the following operating
conditions. In such cases, correct the
operating conditions before using the Intelligent Key function or use the mechanical
key.
— When operating near a location where
strong radio waves are transmitted, such
as a TV tower, power station and broadcasting station.
— When in possession of wireless equipment, such as a cellular telephone,
transceiver, and CB radio.
— When the Intelligent Key is in contact
with or covered by metallic materials.
Pre-driving checks and adjustments
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(175,1)
— When any type of radio wave remote
control is used nearby.
— When the Intelligent Key is placed near
an electric appliance such as a personal
computer.
— When the vehicle is parked near a
parking meter.
.
.
.
.
Although the life of the battery varies
depending on the operating conditions, the
battery’s life is approximately 2 years. If the
battery is discharged, replace it with a new
one. (
“Intelligent Key battery replacement” page 8-27)
Since the Intelligent Key is continuously
receiving radio waves, if the key is left near
equipment which transmits strong radio
waves, such as signals from a TV and
personal computer, the battery life may
become shorter.
Because the steering wheel is locked
electrically, unlocking the steering wheel
with the ignition switch in the LOCK position
is impossible when the vehicle battery is
completely discharged. Pay special attention that the vehicle battery is not completely
discharged.
Do not push the door handle request switch
with the Intelligent Key held in your hand.
The close distance to the door handle will
cause the Intelligent Key system to have
difficulty recognizing that the Intelligent Key
is outside the vehicle.
.
After locking the doors, check that the doors
are securely locked by testing them.
.
To prevent the Intelligent Key from being left
inside the vehicle, make sure you carry the
key with you and then lock the doors.
.
To prevent the Intelligent Key from being left
inside the trunk, make sure you carry the key
with you and then close the trunk.
.
Do not pull the door handle before pushing
the door handle request switch. The door
will be unlocked but will not open. Release
the door handle once and pull it again to
open the door.
INTELLIGENT KEY FUNCTIONS
It is possible to lock/unlock all doors, fuel-filler
door and trunk lid by pushing the request switch
on the outside door handles and the trunk lid.
Intelligent Key operating range
The Intelligent Key functions can only be used
when the Intelligent Key is within the specified
operating range from the request switch. The
operating range is within 31.50 in (80 cm) from
each request switch.
NOTE:
. When the Intelligent Key battery is
discharged or strong radio waves are
present near the operating location,
the Intelligent Key system’s operating
range becomes narrower, and the Intelligent Key may not function properly.
Pre-driving checks and adjustments 3-9
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(176,1)
.
If the Intelligent Key is too close to the
door glass, handle or rear bumper, the
request switches may not function.
.
When the Intelligent Key is within the
operating range, it is possible for anyone who does not carry the Intelligent
Key to push the request switch to lock/
unlock the doors.
Intelligent Key operation
You can lock or unlock the doors without taking
the key out from your pocket or bag.
When you carry the Intelligent Key with you, you
can lock or unlock all doors by pushing the door
A within the range of
handle request switch *
operation.
NOTE:
. When the driver’s door is locked or
unlocked, the fuel-filler door is automatically locked or unlocked at the
same time.
.
When you lock or unlock the doors or
the trunk lid, the hazard indicator will
flash and the horn (or the outside
chime) will sound as a confirmation.
(
“Setting hazard indicator and
3-10 Pre-driving checks and adjustments
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(177,1)
horn mode” page 3-13)
Locking doors:
P position, push
1. Move the shift lever to the &
the ignition switch to the OFF position and
make sure you carry the Intelligent Key with
you.
2. Close all the doors.
3. Push the driver’s or front passenger’s door
handle request switch while carrying the
Intelligent Key with you.
4. All the doors will lock.
5. The hazard indicator flashes twice and the
outside chime sounds twice.
NOTE:
. Doors will lock with the Intelligent Key
while the ignition switch is in the ACC
or ON position.
.
Doors will not lock with the Intelligent
Key while any door is open.
.
Doors will not lock by pushing the door
handle request switch with the Intelligent Key inside the vehicle.
However, when an Intelligent Key is
inside the vehicle, doors can be locked
with another registered Intelligent Key.
Unlocking doors:
1. Push the driver’s or front passenger’s door
handle request switch once while carrying
the Intelligent Key with you.
2. The hazard indicator flashes once and outside chime sounds once. The corresponding
door will unlock.
3. Push the door handle request switch again
within 1 minute.
4. The hazard indicator flashes once and outside chime sounds once again. All the doors
will unlock.
NOTE:
All doors will be locked automatically
unless one of the following operations is
performed within 1 minute after pushing
the request switch while the doors are
locked. If during this 1-minute time period,
the request switch is pushed, all doors will
be locked automatically after another 1
minute.
. Opening any door
.
Pushing the ignition switch
Pre-driving checks and adjustments 3-11
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(178,1)
Opening trunk lid:
A for
1. Push the trunk open request switch *
more than 1 second.
2. The trunk will unlatch. An outside chime will
sound four times.
3. Raise the trunk lid to open the trunk.
NOTE:
. To prevent the Intelligent Key from
being accidentally locked in the trunk,
lockout protection is equipped with the
Intelligent Key system.
.
When the trunk lid is closed with the
Intelligent Key inside the trunk, the
outside buzzer will sound and the trunk
will open.
Battery saver system
When all the following conditions are met for a
period of time, the battery saver system will cut
off the power supply to prevent battery discharge.
.
The ignition switch is in the ACC position,
and
.
All doors are closed, and
.
P position.
The shift lever is in the &
REMOTE KEYLESS ENTRY SYSTEM
It is possible to lock/unlock all doors, fuel-filler
door, and activate the panic alarm by pushing
the buttons on the Intelligent Key.
NOTE:
Before locking the doors, make sure the
Intelligent Key is not left in the vehicle.
Remote keyless entry operating
range
The LOCK/UNLOCK button on the Intelligent
Key can operate at a distance of approximately
33 ft (10 m) from the vehicle. (The effective
distance depends upon the conditions around
the vehicle.)
The lock and unlock buttons on the Intelligent
Key will not operate when:
.
the distance between the Intelligent Key and
the vehicle is over 33 ft (10 m).
. the Intelligent Key battery runs down.
The LOCK/UNLOCK operating range varies
depending on the environment. To securely
operate the lock and unlock buttons, approach
the vehicle to about 3 ft (1 m) from the door.
Remote keyless entry operation
NOTE:
. When the driver’s door is locked or
unlocked, the fuel-filler door is automatically locked or unlocked at the
same time.
.
When you lock or unlock the doors or
the trunk lid, the hazard indicator will
flash and the horn (or the outside
chime) will sound as a confirmation.
(
“Setting hazard indicator and
horn mode” page 3-13)
3-12 Pre-driving checks and adjustments
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(179,1)
Locking doors:
P position, push
1. Move the shift lever to the &
the ignition switch to the OFF position, and
make sure you carry the Intelligent Key with
you.
2. Close all the doors.
1
3. Push the LOCK
button *
on the
Intelligent Key.
4. All the doors will lock.
5. The hazard indicator flashes twice and the
horn chirps once.
NOTE:
. Doors will lock with the Intelligent Key
while the ignition switch is in the ACC
or ON position.
.
Doors will not lock with the Intelligent
Key while any door is open.
Unlocking doors:
2 on the
1. Push the UNLOCK
button *
Intelligent Key once.
2. The hazard indicator flashes once. The
driver’s door will unlock.
2 on the
button *
3. Push the UNLOCK
Intelligent Key again within 60 seconds.
4. The hazard indicator flashes once again. All
the doors will unlock.
All doors will be locked automatically unless one
of the following operations is performed within 1
minute after pushing the UNLOCK button on the
Intelligent Key while the doors are locked. If
during this 1-minute time period, the UNLOCK
button on the Intelligent Key is pushed, all doors
will be locked automatically after another 1
minute.
.
Opening any door
.
Pushing the ignition switch
Opening trunk lid:
3
1. Push the TRUNK
button *
on the
Intelligent Key for more than 1 second.
2. The trunk will unlatch.
3. Raise the trunk lid to open the trunk.
second to turn the panic alarm off.)
SETTING HAZARD INDICATOR AND
HORN MODE
This vehicle is set in hazard indicator and horn
mode when you first receive the vehicle.
When you lock/unlock the doors, the hazard
indicator will flash and the horn (or the outside
chime) will sound as a confirmation.
The following descriptions show how the hazard
indicator and horn will activate when locking/
unlocking the doors and how the horn feature
can be deactivated.
Using panic alarm:
If you are near your vehicle and feel threatened,
you may activate the alarm to call attention as
follows:
4
1. Push the PANIC
button *
on the
Intelligent Key for more than 1 second.
2. The theft warning alarm and headlights will
stay on for 25 seconds.
3. The panic alarm stops when:
. It has run for 25 seconds, or
. Any of the buttons on the Intelligent Key
are pushed. (Note: the panic button
should be pushed for more than 1
Pre-driving checks and adjustments 3-13
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(180,1)
Hazard indicator and horn mode
DOOR LOCK
Intelligent Key system
(Using door handle request
switch or trunk open request
switch)
HAZARD - twice
OUTSIDE CHIME twice
Remote keyless entry sysHAZARD - twice
tem
,
or
button) HORN - once
(Using
DOOR UNLOCK
TRUNK UNLOCK
HAZARD - once
OUTSIDE CHIME once
HAZARD - none
OUTSIDE CHIME - 4
times
HAZARD - once
HORN - none
HAZARD - none
HORN - none
3-14 Pre-driving checks and adjustments
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(181,1)
Hazard indicator mode
WARNING SIGNALS
DOOR LOCK
Intelligent Key system
(Using door handle request
switch or trunk open request
switch)
HAZARD - twice
Remote keyless entry system
HAZARD - twice
(Using
,
or
button)
Switching procedure
The horn beep feature can be deactivated with
the following procedures.
DOOR UNLOCK
TRUNK UNLOCK
HAZARD - none
HAZARD - none
HAZARD - none
HAZARD - none
To help prevent the vehicle from moving
unexpectedly due to an erroneous operation of
the Intelligent Key listed on the following chart or
to help prevent the vehicle from being stolen, a
chime or beep sounds inside and outside the
vehicle and a warning displays in the vehicle
information display. (
“Warning display”
page 2-33) (
“Operation displays” page
2-43)
When a chime or beep sounds or a warning
displays, be sure to check the vehicle and the
Intelligent Key.
1. Push the LOCK
and UNLOCK
buttons simultaneously for more than 2
seconds.
2. The hazard indicator flashes 3 times.
3. The horn beep feature will be deactivated
(Hazard indicator mode).
4. To reactivate the horn beep feature (Hazard
indicator and horn mode), push the buttons
once more. The hazard indicator flashes
once and the horn beeps once.
Pre-driving checks and adjustments 3-15
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(182,1)
TROUBLESHOOTING GUIDE
Symptom
When pushing the ignition
switch to stop the engine
The SHIFT P warning appears on the display and
the inside warning chime sounds continuously.
Action to take
P position. Shift the shift lever to the &
P position.
The shift lever is not in the &
The ignition switch is in the ACC
position.
Push the ignition switch to the OFF
position.
The Intelligent Key is in the Intelligent
Key port.
Remove the Intelligent Key from the
Intelligent Key port.
The NO KEY warning appears on the display, the
outside chime sounds 3 times and the inside
warning chime sounds for approximately 3 seconds.
The ignition switch is in the ACC or
ON position.
Push the ignition switch to the OFF
position.
The SHIFT P warning appears on the display and
the outside chime sounds continuously.
P position and
The ignition switch is in the ACC or
Move the shift lever to the &
OFF position and the shift lever is not push the ignition switch to the OFF
P position.
in the &
position.
When opening the driver’s door
The inside warning chime sounds continuously.
to get out of the vehicle
When closing the door after
getting out of the vehicle
Possible cause
When closing the door with the The outside chime sounds for approximately 3
inside lock knob turned to LOCK seconds and all the doors unlock.
The Intelligent Key is inside the vehicle
Carry the Intelligent Key with you.
or trunk.
The Intelligent Key is inside the vehicle
Carry the Intelligent Key with you.
or trunk.
When pushing the door handle
request switch to lock the door
When closing the trunk lid
The outside chime sounds for approximately 2
seconds.
The outside chime sounds for approximately 10
seconds and the trunk lid opens.
A door is not closed securely.
Close the door securely.
The door handle request switch is
pushed before the door is closed.
Push the door handle request switch after
the door is closed.
The Intelligent Key is inside the trunk.
Carry the Intelligent Key with you.
3-16 Pre-driving checks and adjustments
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(183,1)
HOOD
OPENING THE HOOD
1
1. Pull the hood lock release handle *
located below the instrument panel. The
hood will then spring up slightly.
2 at the front of the hood
2. Pull the lever *
with your fingertips and raise the hood.
3 and
3. Grasp the insulated part of the stay *
release it from the hook, then securely insert
4 .
it into the hood hole *
WARNING
If you see steam or smoke coming from
the engine compartment, do not open
the hood. Doing so could cause injury.
Pre-driving checks and adjustments 3-17
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(184,1)
accident.
CAUTION
.
.
Do not insert hands, clothing, tools
or other items into the engine
compartment while the engine is
running.
.
Do not touch the exhaust system
parts, radiator or other hot parts
until the engine and the parts have
cooled.
CAUTION
When closing the hood, lower it slowly
so that hands or other items do not get
caught.
NOTICE
Do not open the hood while the wiper
arms are lifted away from the windshield. The hood and wipers will be
damaged.
Be sure to check that the hood is
securely closed before driving. If
both sides of the hood are not
locked in place, the hood may open
during driving, possibly causing an
accident.
CLOSING THE HOOD
1. While supporting the hood, store the stay to
the original position.
2. Slowly lower the hood. When it is at a height
of 1 ft (30 cm) or higher, drop the hood and
make sure that both sides of the hood
securely lock in place.
WARNING
.
NOTE:
Because the hood of this vehicle requires
more force to close than that for other
vehicles, the hood will be difficult to close
if you lower it all the way and then attempt
to press it closed. Be sure to drop the hood
from a height of approximately 1 ft (30 cm)
and be sure that both sides securely lock
in place.
Make sure the hood is completely
closed and latched before driving.
Failure to do so could cause the
hood to open and result in an
3-18 Pre-driving checks and adjustments
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(185,1)
TRUNK
WARNING
.
Do not drive with the trunk lid open.
This could allow dangerous exhaust
gases to be drawn into the vehicle.
(
“Exhaust gas (carbon monoxide)” page 5-3)
.
Closely supervise children when
they are around cars to prevent
them from playing and becoming
locked in the trunk where they could
be seriously injured. Keep the car
locked, with the trunk closed, when
not in use, and prevent children’s
access to Intelligent Keys.
TRUNK OPEN REQUEST SWITCH
TRUNK LID RELEASE SWITCH
The trunk lid can be opened by pushing the
A
trunk open request switch *
when the
Intelligent Key is within the operating range of
the trunk lock/unlock function regardless of the
inside lock knob position. (
“Intelligent Key
system” page 3-8)
Press the trunk lid release switch downwards to
unlock the trunk.
Pre-driving checks and adjustments 3-19
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(186,1)
you. (
“Valet hand-off” page 3-3)
To connect the power to the trunk lid, push the
2 .
switch to the ON position *
Except for carbon trunk lid models
TRUNK RELEASE POWER CANCEL
SWITCH
When the switch located inside the glove box is
1 , the power to the trunk
in the OFF position *
lid will be canceled and the trunk lid cannot be
opened by the trunk lid release switch, the trunk
open request switch or the TRUNK button on
the Intelligent Key.
When you have to leave the vehicle with a valet
and want to keep your belongings safe in the
glove box and the trunk, push this switch to OFF
and lock the glove box with the mechanical key.
Then leave the vehicle and the Intelligent Key
with the valet and keep the mechanical key with
For carbon trunk lid models
3-20 Pre-driving checks and adjustments
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(187,1)
OPENING AND CLOSING THE
TRUNK
When opening the trunk, first unlock it then lift
up the trunk lid so that it is fully open.
When closing the trunk, lower the trunk lid and
press it until it is securely locked in place. The
A (except for carbon trunk lid models) or
strap *
B (for carbon trunk lid models) can
the handle *
be used when the trunk lid is dirty.
.
The trunk of this vehicle is slightly
more difficult to close than an ordinary
vehicle (particularly when the vehicle is
new). This is because the trunk rigidity
has been increased to handle the high
load on the rear spoiler during vehicle
operation. This does not indicate that
there is a malfunction. Check that the
trunk is securely locked.
NOTICE
.
.
Open and close the trunk without
grasping the rear spoiler. Grasping
the rear spoiler to open or close the
trunk may damage the spoiler.
Do not leave the key inside the
trunk.
NOTE:
. To prevent the Intelligent Key from
being accidentally locked in the trunk,
lockout protection is equipped with the
Intelligent Key system. When the trunk
lid is closed with the Intelligent Key
inside the trunk, the outside buzzer will
sound and the trunk will open.
EMERGENCY TRUNK LID RELEASE
WARNING
Closely supervise children when they
are around cars to prevent them from
playing and becoming locked in the
trunk where they could be seriously
injured. Keep the car locked, with the
trunk lid securely latched, when not in
use, and prevent children’s access to
Intelligent Keys.
Pre-driving checks and adjustments 3-21
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(188,1)
The emergency trunk lid release mechanism
allows opening of the trunk lid in the event that
people become locked inside the trunk or in the
event of the loss of electrical power such as a
discharged battery.
Inside the trunk
To open the trunk lid from the inside, pull the
1 until the lock releases and
release handle *
push up on the trunk lid. The release lever is
made of a material that glows in the dark after a
brief exposure to ambient light.
The handle is located on the back of the trunk lid
as illustrated.
From the passenger compartment
The trunk can be opened with the emergency
trunk lid opener located on the floor in front of
the passenger’s seat.
1. Remove the board located on the floor in
front of the passenger’s seat.
2. Insert the mechanical key into the emergency trunk lid opener and turn it clockwise
until it stops.
NOTE:
Because the trunk rigidity has been increased to handle the high load on the rear
spoiler during vehicle operation, more
force is required to operate the mechanical
key (particularly when the vehicle is new).
Be sure to turn the key clockwise until it
stops.
3-22 Pre-driving checks and adjustments
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(189,1)
FUEL-FILLER DOOR
The fuel-filler door is located on the right and
rear side of the vehicle.
WARNING
.
.
.
.
Never pour fuel into the throttle
body to attempt to start your vehicle.
.
Do not fill a portable fuel container
in the vehicle or trailer. Static electricity can cause an explosion of
flammable liquid, vapor or gas in
any vehicle or trailer. To reduce the
risk of serious injury or death when
filling portable fuel containers:
Gasoline is extremely flammable
and highly explosive under certain
conditions. You could be burned or
seriously injured if it is misused or
mishandled. Always stop engine
and do not smoke or allow open
flames or sparks near the vehicle
when refueling.
— Always place the container on
the ground when filling.
— Do not use electronic devices
when filling.
Do not attempt to top off the fuel
tank after the fuel pump nozzle
shuts off automatically. Continued
refueling may cause fuel overflow,
resulting in fuel spray and possibly
a fire.
Use only an original equipment type
fuel-filler cap as a replacement. It
has a built-in safety valve needed
for proper operation of the fuel
system and emission control system. An incorrect cap can result in a
serious malfunction and possible
injury. It could also cause the malfunction indicator light to come on.
filler tube, then tighten until the
fuel-filler cap clicks. Failure to tighten the fuel-filler cap properly may
cause the
Malfunction Indicator
Light (MIL) to illuminate. If the
light illuminates because the fuelfiller cap is loose or missing, tighten
or install the cap and continue to
drive the vehicle. The
light
should turn off after a few driving
trips. If the
light does not turn
off after a few driving trips, have the
vehicle inspected by a GT-R certified
NISSAN dealer.
— Keep the pump nozzle in contact
with the container while you are
filling it.
— Use only approved portable fuel
containers for flammable liquid.
NOTICE
.
If fuel is spilled on the vehicle body,
flush it away with water to avoid
paint damage.
.
Insert the cap straight into the fuel-
(
“Malfunction Indicator Light
(MIL)” page 2-31)
.
This vehicle includes a system that
can supply fuel even during high-G
(gravity) turns. The fuel tank pressure is higher when the vehicle is
hot. If the vehicle is refueled when
the vehicle is hot, the fuel pump may
automatically shut off before the
tank is full. This does not indicate
that there is a malfunction.
Pre-driving checks and adjustments 3-23
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(190,1)
OPENING THE FUEL-FILLER DOOR
1. Unlock the fuel-filler door by using one of the
following operations.
. Push the door handle request switch
with the Intelligent Key carried with you.
. Push the UNLOCK button on the Intelligent Key.
. Push the power door lock switch to the
UNLOCK position.
2. Press the rear side of the fuel-filler door to
release the door lock, and open the door.
1 slowly counterclockwise to
3. Turn the cap *
remove it.
During refueling, place the cap on the inside
2 .
of the door *
CLOSING THE FUEL-FILLER DOOR
1. Turn the cap clockwise until a single click
sound is heard.
2. Close the door. Lock the fuel-filler door by
using one of the following operations.
.
Push the door handle request switch with
the Intelligent Key carried with you.
.
Push the LOCK button on the Intelligent
Key.
3-24 Pre-driving checks and adjustments
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(191,1)
STEERING WHEEL
.
Push the power door lock switch to the
LOCK position.
NOTE:
WARNING
.
Do not adjust the steering wheel
while driving. You could lose control
of your vehicle and cause an accident.
.
Do not adjust the steering wheel
any closer to you than is necessary
for proper steering operation and
comfort. The driver’s air bag inflates
with great force. If you are unrestrained, leaning forward, sitting sideways or out of position in any way,
you are at greater risk of injury or
death in a crash. You may also
receive serious or fatal injuries from
the air bag if you are up against it
when it inflates. Always sit back
against the seatback and as far
away as practical from the steering
wheel. Always use the seat belts.
After a single click is heard and the cap is
released it may move slightly. This is not a
malfunction.
TILT/TELESCOPIC STEERING COLUMN
Tilt adjustment
This adjusts up/down the position of the
steering wheel.
1. Press lever
A
*
down
1 .
*
2. Move the steering wheel up/down
stop it in an appropriate position.
2
*
and
A to lock the steering wheel in
3. Lift up lever *
3 .
position *
Pre-driving checks and adjustments 3-25
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(192,1)
Telescopic adjustment
This adjusts the forward/backward position of
the steering wheel.
1. Press lever
B
*
down
1 .
*
2. Move the steering wheel forward/backward
2 and stop it in an appropriate position.
*
B to lock the steering wheel in
3. Lift up lever *
3 .
position *
SUN VISORS
MIRRORS
Lower the sun visor to block sunlight coming
from the forward direction.
INSIDE MIRROR
To block sunlight coming from the side, lower
the sun visor, then unclip it from the hook and
move it to the side.
The inside mirror is designed so that it
automatically changes reflection according to
the intensity of the headlights of the following
vehicle.
The anti-glare system will be automatically
turned on when the ignition switch is pushed
to the ON position.
When the anti-glare system is turned on, the
A will illuminate and excessive
indicator light *
glare from the headlights of the vehicle behind
you will be reduced.
Push the “*” switch
C
*
to make the inside
3-26 Pre-driving checks and adjustments
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(193,1)
rearview mirror operate normally. The indicator
D to turn
light will turn off. Push the “I” switch *
the system on.
Adjusting the outside mirrors
1. Turn the switch right or left to select the right
1 .
or left side mirror *
2 to adjust the
2. Operate the control switch *
mirror angle.
NOTICE
Do not allow any object to cover the
E or apply glass cleaner on
sensors *
them. Doing so will reduce the sensitivity of the sensor, resulting in improper operation.
WARNING
Adjust the mirrors before starting to
drive. Adjusting the mirrors during driving is dangerous as it reduces the
driver’s attention to the forward direction.
OUTSIDE MIRRORS
WARNING
Objects viewed in the outside mirror on
the passenger side are closer than they
appear. Be careful when moving to the
right. Using only this mirror could cause
an accident. Use the inside mirror or
glance over your shoulder to properly
judge distances to other objects.
The outside mirror will operate only when the
ignition switch is in the ACC or ON position.
Pre-driving checks and adjustments 3-27
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(194,1)
vehicle.
.
Folding the outside mirrors
Push the switch down
mirrors.
Push the switch up
before driving.
2
*
1
*
to fold the outside
NOTE:
. If the switch is operated continuously,
the mirror may stop before movement
is completed. This does not indicate
that there is a malfunction. Wait a few
moments, then operate the switch
again.
.
If the mirrors were folded or unfolded
by hand, the mirrors may start moving
when the ignition switch is set to the
ACC or ON position.
.
When the ignition switch is in the ON
position, operating the rear window
defroster will also remove frost and
fog from the outside mirrors.
(
“Rear window defroster switch”
page 2-50)
to unfold the mirrors
CAUTION
.
Do not touch the mirrors while they
are moving. Your hand may be
pinched, and the mirror may malfunction.
.
Do not drive with the mirrors stored.
You will be unable to see behind the
If the mirrors were folded or unfolded by hand, there is a chance
that the mirror will move forward or
backward during driving. If the mirrors were folded or unfolded by
hand, be sure to adjust them again
electrically before driving.
VANITY MIRROR
To use the front vanity mirror, pull down the sun
visor and pull up the cover.
3-28 Pre-driving checks and adjustments
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(195,1)
4 Display screen, heater, air conditioner
and audio systems
Multi Function Display Owner’s Manual ............................. 4-2
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(196,1)
MULTI FUNCTION DISPLAY
OWNER’S MANUAL
Refer to the separate Multi Function Display
Owner’s Manual that includes the following
information.
.
Multi function display system
.
Navigation
.
Audio system
.
Bluetooth® hands-free phone system
.
Heater and air conditioner
.
Viewing information
.
Other settings
.
Voice recognition
.
Monitor system
.
Multi function meter
.
General system information
4-2
Display screen, heater, air conditioner and audio systems
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(197,1)
5 Starting and driving
Precautions when starting and driving ............................... 5-3
Exhaust gas (carbon monoxide) ..................................... 5-3
Three-way catalyst ............................................................. 5-3
Tire Pressure Monitoring System (TPMS) ................... 5-4
Avoiding collision and rollover ........................................ 5-7
Off-road recovery ............................................................... 5-7
Rapid air pressure loss ..................................................... 5-8
Drinking alcohol/drugs and driving ................................ 5-9
All-Wheel Drive (AWD) driving safety precautions .... 5-9
Push-button ignition switch ................................................ 5-10
Operating range for engine start ................................ 5-10
Ignition switch operation ............................................... 5-10
Ignition switch positions ................................................ 5-11
Emergency engine shut off ........................................... 5-11
Intelligent Key battery discharge ................................. 5-12
Before starting the engine .................................................. 5-13
Starting the engine ............................................................... 5-13
Driving the vehicle ................................................................ 5-15
Dual clutch transmission ............................................... 5-15
Driving tips ........................................................................ 5-21
VDC, transmission and suspension setup switches .... 5-25
How to switch the modes ............................................ 5-25
Features of each mode .................................................. 5-27
Turbocharger system ............................................................ 5-31
R mode start function .........................................................
How to use R mode start function ...........................
Parking brake .........................................................................
Cruise control ........................................................................
Precautions on cruise control ....................................
Steering-wheel-mounted controls ............................
Indicators and display ..................................................
Cruise control operations ...........................................
Hill Start Assist System ......................................................
Break-in schedule ................................................................
Wheel alignment ...........................................................
Fuel Efficient Driving Tips ..................................................
Increasing fuel economy .....................................................
All-Wheel Drive (AWD) ......................................................
AWD warning light .......................................................
Tight corner braking phenomenon ...........................
Tires ..................................................................................
AWD system characteristics ......................................
Limited Slip Differential (LSD) ..........................................
Parking/parking on hills .......................................................
Power steering ......................................................................
Brake system .........................................................................
Braking precautions .....................................................
Parking brake break-in .................................................
[ Edit: 2014/ 12/ 8
5-32
5-33
5-33
5-34
5-35
5-35
5-36
5-36
5-38
5-39
5-39
5-40
5-41
5-41
5-41
5-43
5-44
5-44
5-45
5-46
5-47
5-48
5-48
5-48
Model: R35-D ]
(198,1)
Brake assist ............................................................................
Anti-lock Braking System (ABS) ................................
Vehicle Dynamic Control (VDC) system .........................
Cold weather driving ............................................................
Freeing a frozen door lock ............................................
Anti-freeze .........................................................................
Battery ................................................................................
5-49
5-49
5-50
5-52
5-52
5-52
5-52
Draining of coolant water ............................................
Tire equipment ...............................................................
Special winter equipment ...........................................
Driving on snow or ice ................................................
Engine block heater (if so equipped) ......................
Active noise control (if so equipped) ..............................
[ Edit: 2014/ 12/ 8
5-52
5-53
5-53
5-53
5-54
5-54
Model: R35-D ]
(199,1)
PRECAUTIONS WHEN STARTING
AND DRIVING
EXHAUST GAS (carbon monoxide)
WARNING
.
.
Do not leave children or adults who
would normally require the support
of others alone in your vehicle. Pets
should not be left alone either. They
could accidentally injure themselves
or others through inadvertent operation of the vehicle. Also, on hot,
sunny days, temperatures in a
closed vehicle could quickly become
high enough to cause severe or
possibly fatal injuries to people or
animals.
Closely supervise children when
they are around cars to prevent
them from playing and becoming
locked in the trunk where they could
be seriously injured. Keep the car
locked, with the rear seatback and
trunk lid securely latched when not
in use, and prevent children’s access
to car keys.
WARNING
.
.
Do not breathe exhaust gases; they
contain colorless and odorless carbon monoxide. Carbon monoxide is
dangerous. It can cause unconsciousness or death.
If you suspect that exhaust fumes
are entering the vehicle, drive with
all windows fully open, and have the
vehicle inspected immediately.
.
Do not run the engine in closed
spaces such as a garage.
.
Do not park the vehicle with the
engine running for any extended
length of time.
.
Keep the trunk lid closed while
driving, otherwise exhaust gases
could be drawn into the passenger
compartment. If you must drive with
the trunk lid open, follow these
precautions:
circulate the air.
.
The exhaust system and body
should be inspected by a qualified
mechanic whenever:
— The vehicle is raised for service.
— You suspect that exhaust fumes
are entering into the passenger
compartment.
— You notice a change in the
sound of the exhaust system.
— You have had an accident involving damage to the exhaust
system, underbody, or rear of
the vehicle.
THREE-WAY CATALYST
The three-way catalyst is an emission control
device installed in the exhaust system. Exhaust
gases in the three-way catalyst are burned at
high temperatures to help reduce pollutants.
a. Open all the windows.
b. Set the
air recirculation to
off and the fan control to high to
Starting and driving 5-3
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(200,1)
conditions are detected. Have the
vehicle inspected promptly by a
GT-R certified NISSAN dealer.
WARNING
.
.
The exhaust gas and the exhaust
system are very hot. Keep people,
animals or flammable materials
away from the exhaust system components.
Do not stop or park the vehicle over
flammable materials such as dry
grass, waste paper or rags. They
may ignite and cause a fire.
NOTICE
.
Do not use leaded gasoline. Deposits from leaded gasoline seriously
reduce the three-way catalyst’s ability to help reduce exhaust pollutants.
.
Keep your engine tuned up. Malfunctions in the ignition, fuel injection, or electrical systems can cause
overrich fuel flow into the three-way
catalyst, causing it to overheat. Do
not keep driving if the engine misfires, or if noticeable loss of performance or other unusual operating
5-4
.
Avoid driving with an extremely low
fuel level. Running out of fuel could
cause the engine to misfire, damaging the three-way catalyst.
.
Do not race the engine while warming it up.
.
Do not push or tow your vehicle to
start the engine.
TIRE PRESSURE MONITORING
SYSTEM (TPMS)
Each tire should be checked monthly when cold
and inflated to the inflation pressure recommended by the vehicle manufacturer on the
vehicle placard or tire inflation pressure label. (If
your vehicle has tires of a different size than the
size indicated on the vehicle placard or tire
inflation pressure label, you should determine
the proper tire inflation pressure for those tires.)
As an added safety feature, your vehicle has
been equipped with a Tire Pressure Monitoring
System (TPMS) that illuminates a low tire
pressure telltale when one or more of your tires
is significantly under-inflated. Accordingly, when
the low tire pressure telltale illuminates, you
should stop and check your tires as soon as
possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire
causes the tire to overheat and can lead to tire
failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the
vehicle’s handling and stopping ability.
If the vehicle is being driven with one or more flat
tires, the low tire pressure warning light will
illuminate continuously and a chime will sound
for 10 seconds. The chime will only sound at the
first indication of a flat tire, and the warning light
will illuminate continuously. When the flat tire
warning is activated, have the system reset and
the tire checked and replaced if necessary by a
GT-R certified NISSAN dealer. Even if the tire is
inflated to the specified COLD tire pressure, the
warning light will continue to illuminate until the
system is reset by a GT-R certified NISSAN
dealer. Your vehicle can be driven for a limited
time on a flat tire. (
“Run-flat tires” page 839)
Please note that the TPMS is not a substitute for
proper tire maintenance, and it is the driver’s
responsibility to maintain correct tire pressure,
even if under-inflation has not reached the level
to trigger illumination of the TPMS low tire
pressure telltale.
Starting and driving
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(201,1)
Your vehicle has also been equipped with a
TPMS malfunction indicator to indicate when the
system is not operating properly. The TPMS
malfunction indicator is combined with the low
tire pressure telltale. When the system detects a
malfunction, the telltale will flash for approximately one minute and then remain continuously
illuminated. This sequence will continue upon
subsequent vehicle start-ups as long as the
malfunction exists. When the malfunction indicator is illuminated, the system may not be able
to detect or signal low tire pressure as intended.
TPMS malfunctions may occur for a variety of
reasons, including the installation of replacement or alternate tires or wheels on the vehicle
that prevent the TPMS from functioning properly.
Always check the TPMS malfunction telltale
after replacing one or more tires or wheels on
your vehicle to ensure that the replacement or
alternate tires and wheels allow the TPMS to
continue to function properly.
ER” warning does not appear if the low tire
pressure warning light illuminates to indicate
a TPMS malfunction.
Additional information
.
.
.
The TPMS will activate only when the
vehicle is driven at speeds above 16 MPH
(25 km/h). Also, this system may not detect
a sudden drop in tire pressure (for example a
flat tire while driving).
The low tire pressure warning light does not
automatically turn off when the tire pressure
is adjusted. After the tire is inflated to the
recommended pressure, the vehicle must be
driven at speeds above 16 MPH (25 km/h)
to activate the TPMS and turn off the low tire
pressure warning light. Use a tire pressure
gauge to check the tire pressure.
The “TIRE LOW PRESSURE - VISIT DEALER” warning appears in the vehicle information display when the low tire pressure
warning light is illuminated and low tire
pressure is detected. The “TIRE LOW
PRESSURE - VISIT DEALER” warning turns
off when the low tire pressure warning light
turns off.
The “TIRE LOW PRESSURE - VISIT DEALER” warning appears each time the ignition
switch is placed in the “ON” position as long
as the low tire pressure warning light
remains illuminated.
The “TIRE LOW PRESSURE - VISIT DEAL-
.
The “FLAT TIRE - VISIT DEALER” warning
appears in the vehicle information display
when the low tire pressure warning light is
illuminated and one or more flat tires are
detected.
.
Tire pressure rises and falls depending on
the heat caused by the vehicle’s operation
and the outside temperature. Low outside
temperature can lower the temperature of
the air inside the tire which can cause a
lower tire inflation pressure. Altitude can
also affect tire pressure. These may cause
the low tire pressure warning light to
illuminate. If the warning light illuminates,
check the tire pressure for all four tires.
.
GT-R vehicles are delivered from the factory
with nitrogen-filled tires. For best performance, NISSAN recommends that GT-R
owners maintain their vehicles by using
nitrogen for tire inflation. Because nitrogen
is more stable than compressed air, it is less
prone to pressure fluctuation resulting from
temperature variations. If nitrogen is not
available, compressed air may be safely
used under normal driving conditions. However, NISSAN recommends refilling with
Starting and driving 5-5
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(202,1)
Nitrogen for maximum tire performance.
.
The Tire and Loading Information label (also
referred to as the vehicle placard or tire
inflation pressure label) is located in the
driver’s door opening.
.
You can also check the pressure of all tires
on the multi function display. Refer to the
separate Multi Function Display Owner’s
Manual.
.
The tire pressure sensor should be reset
anytime the wheels or tires are removed or
replaced.
.
If the tire is removed in order to replace the
tire pressure sensor battery, it may not be
possible to reuse the removed tire from the
wheel. To replace the tire pressure sensor
battery, contact a GT-R certified NISSAN
dealer.
may permanently damage the tires
and increase the likelihood of tire
failure. Serious vehicle damage
could occur and may lead to an
accident and could result in serious
personal injury. Check the tire pressure for all four tires. Adjust the tire
pressure to the recommended COLD
tire pressure shown on the Tire and
Loading Information label to turn
the low tire pressure warning light
off. If the light still illuminates while
driving after adjusting the tire pressure, a tire may be flat.
.
WARNING
.
5-6
If the low tire pressure warning light
illuminates while driving, avoid sudden steering maneuvers or abrupt
braking, reduce vehicle speed, pull
off the road to a safe location and
stop the vehicle as soon as possible. Driving with under-inflated tires
.
Although you can continue driving
with a punctured run-flat tire, remember that vehicle handling stability is reduced, which could lead to
an accident and personal injury.
Also, driving a long distance at high
speeds may damage the tires.
Do not drive at speeds above 50
MPH (80 km/h) and do not drive
more than 50 miles (80 km) with a
punctured run-flat tire. The actual
distance the vehicle can be driven
on a flat tire depends on outside
temperature, vehicle load, road conditions and other factors.
.
When a wheel is replaced, the TPMS
will not function and the low tire
pressure warning light will flash for
approximately 1 minute. The light
will remain on after 1 minute. Contact your GT-R certified NISSAN
dealer as soon as possible for tire
replacement and/or system resetting.
.
Replacing tires with those not originally specified by NISSAN could
affect the proper operation of the
TPMS.
.
Do not inject any tire liquid or
aerosol tire sealant into the tires,
as this may cause a malfunction of
the tire pressure sensors.
NOTICE
.
The TPMS may not function properly
when the wheels are equipped with
tire chains or the wheels are buried
in snow.
.
The TPMS may not function properly
if the TPMS sensor is not reset and
when wheels/tires from another
Starting and driving
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(203,1)
GT-R are installed on your vehicle.
.
The TPMS will not function properly
if non-GT-R wheels are installed on
the vehicle.
.
Do not place metalized film or any
metal parts (antenna, etc.) on the
windows. This may cause poor reception of the signals from the tire
pressure sensors, and the TPMS will
not function properly.
Some devices and transmitters may temporarily
interfere with the operation of the TPMS and
cause the low tire pressure warning light to
illuminate. Some examples are:
.
Facilities or electric devices using similar
radio frequencies are near the vehicle.
.
If a transmitter set to similar frequencies is
being used in or near the vehicle.
.
If a computer (or similar equipment) or a DC/
AC converter is being used in or near the
vehicle.
FCC Notice:
For USA:
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Note: Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s
authority to operate the equipment.
For Canada:
This device complies with Industry Canada
licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must
accept any interference, including interference that may cause undesired operation
of the device.
AVOIDING COLLISION AND ROLLOVER
WARNING
Failure to operate this vehicle in a safe
and prudent manner may result in loss
of control or an accident.
Be alert and drive defensively at all times. Obey
all traffic regulations. Avoid excessive speed,
high speed cornering, or sudden steering
maneuvers, because these driving practices
could cause you to lose control of your vehicle.
As with any vehicle, a loss of control could
result in a collision with other vehicles or
objects, or cause the vehicle to rollover,
particularly if the loss of control causes the
vehicle to slide sideways. Be attentive at all
times, and avoid driving when tired. Never drive
when under the influence of alcohol or drugs
(including prescription or over-the-counter
drugs which may cause drowsiness). Always
wear your seat belt as outlined in this manual,
and also instruct your passengers to do so.
(
“Seat belts” page 1-6)
Seat belts help reduce the risk of injury in
collisions and rollovers. In a rollover crash, an
unbelted or improperly belted person is
significantly more likely to be injured or
killed than a person properly wearing a
seat belt.
OFF-ROAD RECOVERY
While driving, the right side or left side wheels
may unintentionally leave the road surface. If this
occurs, maintain control of the vehicle by
following the procedure below. Please note that
this procedure is only a general guide. The
vehicle must be driven as appropriate based on
the conditions of the vehicle, road and traffic.
Starting and driving 5-7
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(204,1)
1. Remain calm and do not overreact.
2. Do not apply the brakes.
3. Maintain a firm grip on the steering wheel
with both hands and try to hold a straight
course.
4. When appropriate, slowly release the accelerator pedal to gradually slow the vehicle.
5. If there is nothing in the way, steer the
vehicle to follow the road while the vehicle
speed is reduced. Do not attempt to drive
the vehicle back onto the road surface until
vehicle speed is reduced.
6. When it is safe to do so, gradually turn the
steering wheel until both tires return to the
road surface. When all tires are on the road
surface, steer the vehicle to stay in the
appropriate driving lane.
. If you decide that it is not safe to return
the vehicle to the road surface based on
vehicle, road or traffic conditions, gradually slow the vehicle to a stop in a safe
place off the road.
RAPID AIR PRESSURE LOSS
Rapid air pressure loss or a “blow-out” can
occur if the tire is punctured or is damaged due
to hitting a curb or pothole. Rapid air pressure
loss can also be caused by driving on underinflated tires.
Rapid air pressure loss can affect the handling
and stability of the vehicle, especially at highway
speeds.
The vehicle generally moves or pulls
in the direction of the flat tire.
.
Do not rapidly apply the brakes.
.
Do not rapidly release the accelerator pedal.
.
Do not rapidly turn the steering
wheel.
Help prevent rapid air pressure loss by maintaining the correct air pressure and visually
inspect the tires for wear and damage.
(
“Wheels and tires” page 8-32)
1. Remain calm and do not overreact.
If a tire rapidly loses air pressure or “blows-out”
while driving maintain control of the vehicle by
following the procedure below. Please note that
this procedure is only a general guide. The
vehicle must be driven as appropriate based on
the conditions of the vehicle, road and traffic.
3. When appropriate, slowly release the accelerator pedal to gradually slow the vehicle.
WARNING
The following actions can increase the
chance of losing control of the vehicle if
there is a sudden loss of tire air
pressure. Losing control of the vehicle
may cause a collision and result in
personal injury.
5-8
.
2. Maintain a firm grip on the steering wheel
with both hands and try to hold a straight
course.
4. Gradually steer the vehicle to a safe location
off the road and away from traffic if possible.
5. Lightly apply the brake pedal to gradually
stop the vehicle.
6. Turn on the hazard warning flashers and
contact a roadside emergency service to
change the tire.
Starting and driving
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(205,1)
DRINKING ALCOHOL/DRUGS AND
DRIVING
WARNING
Never drive under the influence of
alcohol or drugs. Alcohol in the bloodstream reduces coordination, delays
reaction time and impairs judgement.
Driving after drinking alcohol increases
the likelihood of being involved in an
accident injuring yourself and others.
Additionally, if you are injured in an
accident, alcohol can increase the severity of the injury.
NISSAN is committed to safe driving. However,
you must choose not to drive under the influence
of alcohol. Every year thousands of people are
injured or killed in alcohol-related accidents.
Although the local laws vary on what is
considered to be legally intoxicated, the fact is
that alcohol affects all people differently and
most people underestimate the effects of
alcohol.
Remember, drinking and driving don’t mix! And
that is true for drugs, too (over-the-counter,
prescription, and illegal drugs). Don’t drive if
your ability to operate your vehicle is impaired by
alcohol, drugs, or some other physical condition.
.
Do not attempt to test an AWD
equipped vehicle on a 2-wheel dynamometer, (such as the dynamometers used by some states for
emissions testing), or similar equipment even if the other two wheels
are raised off the ground. Make sure
you inform test facility personnel
that your vehicle is equipped with
AWD before it is placed on a
dynamometer. Using the wrong test
equipment may result in drivetrain
damage or unexpected vehicle
movement which could result in
serious vehicle damage or personal
injury.
.
When a wheel is off the ground due
to an unlevel surface, do not spin
the wheel excessively.
ALL-WHEEL DRIVE (AWD) DRIVING
SAFETY PRECAUTIONS
WARNING
.
Do not drive beyond the performance capability of the tires, even
with AWD engaged. Accelerating
quickly, sharp steering maneuvers
or sudden braking may cause loss
of control.
.
Always use the specified tires on all
four wheels. Install tire chains on
the rear wheels when driving on
slippery roads and drive carefully.
.
This vehicle is not designed for
offroad (rough road) use. Do not
drive on sandy or muddy roads that
tires may get stuck in.
.
Do not attempt to raise two wheels
off the ground and shift the transA ↔&
R position
M or &
mission to any &
with the engine running. Doing so
may result in drivetrain damage or
unexpected vehicle movement
which could result in serious vehicle
damage or personal injury.
Starting and driving 5-9
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(206,1)
PUSH-BUTTON IGNITION SWITCH
WARNING
Do not operate the push-button ignition
switch while driving the vehicle except
in an emergency. (The engine will stop
when the ignition switch is pushed
three consecutive times or the ignition
switch is pushed and held for more than
2 seconds.) If the engine stops while
the vehicle is being driven, this could
lead to a crash and serious injury.
Before operating the push-button ignition
switch, be sure to move the shift lever to the
P position.
&
OPERATING RANGE FOR ENGINE
START
The operating range for starting the engine
inside the vehicle is shown in the illustration.
.
.
If the Intelligent Key is on the instrument
panel, rear parcel shelf, inside the glove box,
door pocket, cup holders or console box, or
the corner of the passenger compartment, it
may not be possible to start the engine.
Carry the Intelligent-Key and try to start the
engine again.
If the Intelligent Key is near the door or door
glass outside the vehicle, it may be possible
to start the engine.
IGNITION SWITCH OPERATION
When the Intelligent Key is carried with you and
the ignition switch is pushed without depressing
the brake pedal, the ignition switch position will
change as follows:
.
Push center once to change to ACC.
.
Push center two times to change to ON.
.
Push center three times to change to OFF.
(No position illuminates.)
.
Push center four times to return to ACC.
.
Open or close any door to return to LOCK
during the OFF position.
5-10 Starting and driving
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(207,1)
IGNITION SWITCH POSITIONS
LOCK (Normal parking position)
The ignition switch can only be locked in this
position.
The ignition switch will be unlocked when it is
pushed to the ACC position while carrying the
Intelligent Key or with the Intelligent Key inserted
in the port.
ACC (Accessories)
NOTE:
. If the steering lock release malfunction
indicator appears on the vehicle information display when the ignition
switch is pressed, press the ignition
switch again while gently turning the
steering wheel left and right.
(
“Steering lock release malfunction indicator” page 2-44)
.
This position activates electrical accessories
such as the radio, when the engine is not
running.
ON (Normal operating position)
This position turns on the ignition system and
electrical accessories.
P warning appears on the
If the shift &
vehicle information display when the
ignition switch is pushed, the shift lever
P posiis in any position except the &
P
tion. Move the shift lever to the &
position. (
“Shift “P” warning”
page 2-43)
.
If the Intelligent Key battery discharge
indicator appears on the vehicle information display, the Intelligent Key
battery is discharged and the ignition
switch will not operate. Insert the
Intelligent Key into the key port to
operate the ignition switch.
(
“Intelligent Key battery discharge
indicator” page 2-45)
.
When all of the following conditions
are met for 60 minutes, the battery
saver system will cut off the power
supply to prevent battery discharge.
OFF
The engine can be turned off without locking the
steering wheel.
The ignition lock is designed so that the ignition
switch cannot be switched to the LOCK position
P position.
until the shift lever is moved to the &
— The ignition switch is in the ACC
position, and
— All doors are closed, and
P position.
— The shift lever is in the &
.
Do not
ignition
position
ning for
This can
leave the vehicle with the
switch in the ACC or ON
when the engine is not runan extended period of time.
discharge the battery.
EMERGENCY ENGINE SHUT OFF
To shut off the engine in an emergency situation
while driving, perform the following procedure:
.
Rapidly push the push-button ignition switch
3 consecutive times in less than 1.5
seconds, or
.
Push and hold the push button ignition
switch for more than 2 seconds.
Starting and driving 5-11
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(208,1)
the Intelligent Key out of the port.
NOTICE
Never place anything except the Intelligent Key in the Intelligent Key port.
Doing so may cause damage to the
equipment.
INTELLIGENT KEY BATTERY DISCHARGE
If the battery of the Intelligent Key is almost
1 of the Intelligent
discharged, the guide light *
Key port blinks and the indicator appears on the
vehicle information display. (
“Intelligent Key
insertion indicator” page 2-44)
In this case, inserting the Intelligent Key into the
port allows you to start the engine. Make sure
that the mechanical key side faces backward as
illustrated. Insert the Intelligent Key in the port
until it is latched and secured.
To remove the Intelligent Key from the port, push
the ignition switch to the OFF position and pull
NOTE:
. Make sure the Intelligent Key is in the
correct direction when inserting it into
the Intelligent Key port. The engine
may not start if it is in the incorrect
direction.
.
Remove the Intelligent Key from the
Intelligent Key port after the ignition
switch is pushed to the OFF position.
.
The Intelligent Key port does not
charge the Intelligent Key battery. If
you see the low battery indicator in the
vehicle information display, replace the
battery as soon as possible.
5-12 Starting and driving
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(209,1)
(
“Intelligent Key battery replacement” page 8-27)
BEFORE STARTING THE ENGINE
STARTING THE ENGINE
.
Make sure the area around the vehicle is
clear.
.
Check fluid levels such as engine oil, coolant, brake fluid and window washer fluid as
frequently as possible, or at least whenever
you refuel.
.
Check that all windows and lights are clean.
NOTE:
. This vehicle includes spark plugs that
are designed for maximum performance. If the start time becomes longer, the plugs may be fouled, making the
engine difficult to start. If this occurs,
start the engine using the procedure
described in this section.
.
Visually inspect tires for their appearance
and condition. Also check tires for proper
inflation.
.
Lock all doors.
.
Position seat.
.
Adjust inside and outside mirrors.
.
Fasten seat belts and ask all passengers to
do likewise.
.
Check the operation of warning lights when
the ignition switch is pushed to the ON
position. (
“Warning lights, indicator
lights and audible reminders” page 2-25)
.
A click sound may be heard when the
brake pedal is depressed and released.
This is normal.
.
A low rattling operating sound may
occur when the engine is started or
stopped. This is because of the transmission gear design, light flywheel and
dry sump lubrication system used in
this transmission. This does not indicate that there is a malfunction. This
sound is likely to occur in particular if
the engine is stopped when the temperature of the transmission oil is high.
Starting and driving 5-13
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(210,1)
1. Check the positions of the accelerator pedal
1 and brake pedal *
2 . Adjust the steering
*
wheel and seat positions so that the correct
driving posture is achieved. (
“Front
seats” page 1-3)
2. Check that the parking brake is engaged.
P or &
N
3. Check that the shift lever is in the &
P is recommended.)
position. (&
4. Firmly depress the brake pedal. Without
depressing the accelerator pedal, push the
ignition switch once to start the engine.
5. To stop the engine, move the shift lever to
P position, and push the ignition switch
the &
to the OFF position.
NOTE:
. Care should be taken to avoid situations that can lead to potential battery
discharge and potential no-start conditions such as:
a. Installation or extended use of electronic accessories that consume
battery power when the engine is
not running (Phone chargers, GPS,
DVD players, etc.)
b. Vehicle is not driven regularly and/
or only driven short distances.
In these cases, the battery may need to
be charged to maintain battery health.
. If the engine is difficult to start, depress the accelerator pedal all the way
to the floor and hold it. Push the
ignition switch with the brake pedal
depressed to start cranking the engine.
After 5 or 6 seconds, stop cranking by
pushing the ignition switch to the OFF
position, and then release the accelerator pedal. Then perform steps 1 to 5
to start the engine. If the engine starts,
but fails to run, repeat this procedure.
.
Starting and stopping the engine over a
short period of time may make the
vehicle more difficult to start. If this
occurs, wait for more than 3 minutes,
and then push the ignition switch again
to start the engine.
.
To maintain high performance over a
long period of time, the engine speed is
limited to 5,000 rpm when the engine is
N or
revved with the shift lever in the &
P
& position, and to 4,000 rpm when the
engine oil or coolant temperature is
low or higher than normal.
.
If the ignition switch is pushed before
P
the shift lever is moved to the &
position, the ignition switch will not
change to the OFF position. If this
P warning display
occurs, the SHIFT &
appears on the vehicle information
display. When stopping the engine, be
P
sure to move the shift lever to the &
position and then push the ignition
switch. Failure to do so may result in
discharge of the battery. (
“Shift
“P” warning” page 2-43)
.
A ↔&
R
M or &
If the shift lever was in the &
position when the engine was stopped,
then be sure to move the shift lever to
P position before starting the
the &
engine the next time. If the engine is
N
started with the shift lever in the &
position, then it may not be possible to
5-14 Starting and driving
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(211,1)
DRIVING THE VEHICLE
drive the vehicle even when the shift
A ↔&
R
M or &
lever is moved to the &
P
position. If this occurs, the SHIFT &
warning appears on the vehicle information display. (
“Shift “P” warning” page 2-43)
CAUTION
If the engine was stopped soon when
the engine is hot, the cooling fan may
operate for approximately 2 minutes
after the engine was stopped to cool
the components in the engine compartment. When the cooling fan is operating, be sure that hands or other items
do not get caught in it.
DUAL CLUTCH TRANSMISSION
The GT-R dual clutch transmission is a newlydeveloped system that uses an electronically
controlled multiple-disc wet clutch attached to
the highly efficient manual transmission. This
transmission has two driving modes.
.
Gear clearances
.
Ultralight flywheel
. Dry sump lubrication
These noises do not indicate that there is a
malfunction.
WARNING
A position (Automatic gearshift):
&
allows automatic shifting of the manual
transmission.
.
.
.
Do not depress the accelerator
P or
pedal while shifting from the &
N position to the &
R or &
A ↔&
M
&
position. Always depress the brake
pedal until shifting is completed.
Failure to do so could cause loss
of control and an accident.
.
Cold engine idle speed is high, so
use caution when shifting into a
forward or reverse gear before the
engine has warmed up.
.
P or &
R position
Never shift to the &
while the vehicle is moving forward.
P or &
A ↔&
M
Never shift to the &
position while the vehicle is moving
rearward. Doing so could cause loss
of control and an accident.
.
The shift lever contains a powerful
magnet. Do not place electronic
M position (Manual gearshift):
&
allows quick shifting of the manual transmission.
NOTE:
When starting or driving on a steep uphill
M position and operate
grade, shift to the &
the paddle shifter to shift down to 1st gear
similar to a manual transmission vehicle.
The GT-R dual clutch transmission was developed specifically to maximize vehicle performance and driving enjoyment. The GT-R
transmission components were designed using
different engineering standards than typical
passenger car transmissions. Because of this,
the GT-R has different operating characteristics,
and various rattle noises may be heard during
some driving conditions because of the following items:
Starting and driving 5-15
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(212,1)
partially engaged. Keep the brake
pedal firmly depressed when the
vehicle is stopped. In some circumstances the vehicle may not start
moving on its own, however this
does not indicate that there is a
malfunction.
medical devices or other electronic
products that are susceptible to
magnetic force close to the shift
lever.
.
Do not downshift abruptly on slippery roads. This may cause a loss of
control.
.
R to
If the shift lever is moved from &
A ↔&
A ↔&
R
M position, or &
M to &
&
position before the vehicle stops,
you may not be able to shift gear or
it may take longer to shift gear.
Make sure to depress the brake
pedal and check that the vehicle
has stopped before shifting.
CAUTION
.
Because the vehicle includes a dual
clutch transmission that automatically controls the clutch and shifting
operation of the manual transmission, whenever the shift lever is in a
P or &
N , the
position other then &
vehicle will begin to move slowly, in
the same way as when the clutch in
a manual transmission vehicle is
faster than 4,000 rpm.
NOTICE
.
When the vehicle is stopped on a
hill, do not hold the vehicle in place
by depressing the accelerator pedal.
Doing so may cause the clutch to
overheat and result in transmission
damage. Use the brakes to prevent
the vehicle from moving.
.
The GT-R dual clutch transmission is
provided with a dry sump lubrication
system that improves efficiency and
ensures reliability under high gforce conditions. When oil viscosity
is high at low temperatures, it takes
longer for all components to be
sufficiently lubricated. Thus, when
the transmission temperature is low
(approximately 1048F (408C), do not
accelerate rapidly or run the engine
5-16 Starting and driving
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(213,1)
Shift lever operation
Push the button while depressing the
brake pedal.
Push the button.
Just move the shift lever.
Automatically returns.
P position:
&
N position:
&
Neither forward nor reverse gear is engaged.
A ↔&
M position:
&
Use this position for all normal forward driving.
A and
The shift lever can be moved between &
M to alternately change each other. The
&
position indicator indicates the gear position
with the indication of “A” or “M”.
.
Operating the shift lever
After starting the engine, fully depress the brake
P
pedal and move the shift lever from the &
R, &
N , or &
A ↔&
M position. Push
position to the &
P or &
R position. All
the button to shift into the &
other positions can be selected without pushing
the button.
.
M position: Operate the paddle shifter to
&
drive in first gear to sixth gear as desired.
.
The position indicator blinks if it is not
possible to shift the gear.
(
“Transmission position indicator”
page 2-9)
CAUTION
P position only when the
Use the &
vehicle is completely stopped.
A position: Use this position for ordinary
&
driving, with the gears shifted automatically
from first gear to sixth gear according to the
speed and driving conditions.
Use this position for parking and starting the
engine. The ignition switch will be changed to
the OFF or LOCK position.
R position:
&
Use this position for driving in reverse. A chime
will sound inside the vehicle and a warning will
appear in the vehicle information display if the
R position for more than 5
shift lever is in the &
minutes, or when the driver’s door is opened
R position.
while the shift lever is in the &
Starting and driving 5-17
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(214,1)
NOTICE
.
Be sure to observe the following
precautions. Failure to do so may
result in shift lever malfunction.
— Do not spill water, beverages or
other liquids on the shift lever.
— Do not allow sand or similar
substances to contact the shift
lever.
.
CAUTION
.
.
Grip the shift lever correctly when
operating it. Failure to do so may
cause a finger or other items to be
trapped between the lever and gate,
possibly causing an accident.
Because rolling resistance is reduced in the GT-R, the vehicle can
move when on a road with a slight
N posigradient, even when in the &
tion. Be sure to depress the brake
pedal.
Develop the habit of performing the
operations marked with “
” without pressing the button. If the
button is pressed at these times,
there is the possibility that the lever
P or &
R
could accidentally enter the &
positions.
.
When the vehicle is hot, the area
around the shift lever may be hot or
may produce an unusual sound,
however this does not indicate that
there is a malfunction.
.
Avoid depressing the brake and
accelerator pedals at the same time.
Depressing both pedals at the same
time could cause the clutch to overheat and accelerate deterioration.
NOTE:
. When moving the shift lever out of the
P position, it may not be possible to
&
move the shift lever if the button is
pressed before the brake pedal is
depressed. Press the button only after
depressing the brake pedal.
.
Do not place coins or other small
objects in the area around the shift
lever. These objects may get stuck in
the shift gate and prevent the shift
lever from moving into a position.
Sometimes, you may not be able to
retrieve these objects.
.
Immediately after a cold start, while the
transmission system check display (“T/
M SYSTEM CHECK IN PROCESS”)
appears on the vehicle information
display, the shift lever cannot be moved
P position. This is because a
out of the &
check of the transmission system is in
progress. This does not indicate that
there is a malfunction. Move the shift
lever after the message on the vehicle
information display turns off.
.
The shift lever knob and consolemounted shift indicator have a genuine
leather finish that requires proper care
5-18 Starting and driving
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(215,1)
and maintenance. (
terior” page 7-7)
5. Push the shift lever button and move the
N position while holding
shift lever to the &
down the shift lock.
Push the ignition switch to the ON position to
unlock the steering wheel. Now the vehicle may
be moved to the desired location.
If the battery is discharged completely, the
steering wheel cannot be unlocked. Do not
move the vehicle with the steering wheel locked.
“Cleaning in-
NOTICE
Shift lock release
If the battery charge is low or discharged, the
P
shift lever may not be moved from the &
position even with the brake pedal depressed
and the shift lever button pushed.
To move the shift lever, perform the following
procedure.
1. Push the ignition switch to the OFF or LOCK
position.
2. Apply the parking brake.
3. Remove the shift lock cover using a suitable
tool wrapped with a cloth.
4. Push down the shift lock as illustrated.
If the shift lever cannot be moved out of
P position after performing the
the &
shift lock release procedure, immediately have the vehicle inspected by a
GT-R certified NISSAN dealer.
Adaptive shift control
The adaptive shift control system automatically
A
operates when the transmission is in the &
position and selects an appropriate gear depending on the road conditions such as uphill,
downhill or curving roads.
Control on uphill and curving roads:
A low gear is maintained that suits the degree of
the slope or curve to allow smooth driving with a
small number of shifts.
Starting and driving 5-19
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(216,1)
Control on downhill roads:
The adaptive shift control system shifts to a low
gear that suits the degree of the slope, and uses
the engine brake to reduce the number of times
that the foot brake must be used.
Control on winding roads:
A low gear is maintained on continuous curves
that involve repeated acceleration and deceleration, so that smooth acceleration is available
instantly when the accelerator pedal is depressed.
and the second and later operations change the
gears.
A position, move the shift lever
To return to the &
M side again. The position indicator
to the &
indicates the gear position with the indication of
“A”.
NOTE:
Adaptive shift control may not operate
when the transmission oil temperature is
low immediately after the start of driving
or when it is very hot. If this occurs, switch
M position and downshift if necesto the &
sary.
M position
&
M position:
Changing to the &
A
M position from the &
To change to the &
M
position, either move the shift lever to the &
side or operate the paddle shifter. The position
indicator indicates the gear position with the
indication of “M”.
If the paddle shifter is used, the first operation
A position to the &
M position,
changes from the &
Changing gears using paddle shifters:
NOTE:
The vehicle cannot be accelerated from a
stop condition while the gear is in the 2nd
to 6th position. When accelerating the
vehicle from a stop condition, use the 1st
gear position.
To shift up, pull the paddle shifter on the right
1 toward you.
side *
To shift down, pull the paddle shifter on the left
2 toward you.
side *
5-20 Starting and driving
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(217,1)
.
.
.
.
.
.
First gear:
Use this position when accelerating from a
stop, climbing a steep hill slowly or engine
braking at low speeds.
Second gear:
Use this position when accelerating or
engine braking at mid-low speeds.
Third gear:
Use this position when accelerating or
gently engine braking at middle speeds.
Fourth gear:
Use this position when accelerating or
gently engine braking at mid-high speeds.
Fifth gear:
Use this position for all normal forward
driving at highway speeds. Engine braking
is weaker in this position.
Sixth gear:
Use this position for all normal forward
driving at highway speeds. Engine braking
is weakest in this position.
Suggested maximum speed in each gear:
Downshift to a lower gear if the engine is not
running smoothly, or if you need to accelerate.
Do not exceed the maximum suggested speed
(shown below) in any gear. For level road
driving, use the highest gear suggested for that
speed. Always observe posted speed limits, and
drive according to the road conditions that will
ensure safe operation. Do not over-rev the
engine when shifting to a lower gear as it may
cause engine damage or loss of vehicle control.
Gear
After starting the engine, fully depress the foot
brake pedal and push the shift lever button
P position
before shifting the shift lever from the &
R, &
N , or &
A ↔&
M position. Be sure the
to the &
vehicle is fully stopped before attempting to shift
the shift lever.
The transmission is designed so that the foot
brake pedal must be depressed before shifting
P to any other position.
from &
P
The shift lever cannot be moved out of the &
position and into any other position with the
ignition switch other in the LOCK, OFF or ACC
position.
When accelerating from a stop
Keep the foot brake pedal depressed and push
the shift lever button to shift into a driving gear
as following:
.
MPH (km/h)
1st
36 (58)
2nd
63 (102)
3rd
91 (148)
4th
—
5th
—
—
6th
DRIVING TIPS
To drive forward, move the shift lever to the
A ↔&
M position.
&
.
R
To back up, move the shift lever to the &
position.
Starting on level ground or an uphill:
1. Check the shift lever position indicator on
the meter to confirm that the driving gear is
selected.
Starting and driving 5-21
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(218,1)
2. Release the parking brake.
3. Release the foot brake pedal gradually, then
slowly depress the accelerator pedal to start
the vehicle in motion.
“R mode start function” page 5-32)
(
When driving the vehicle
Hill climbing:
WARNING
.
When the vehicle speed decreases, depress the accelerator pedal to the floor with
A position. This
the shift lever in the &
automatically shifts the transmission into a
lower gear and maintains this position
depending on the gradient of the hill.
.
The system may down shift according to the
accelerator pedal position and the vehicle
speed.
.
If the transmission is frequently changing
M position
gears while driving, switch to the &
and select the appropriate gear for the
driving conditions.
N
Do not move the shift lever to the &
position while driving. Doing so may
result in an accident due to loss of
engine braking. It may also damage the
transmission.
NOTE:
. To prevent the clutch from overheating
when the parking brake is applied,
engine output is limited when the
accelerator pedal is depressed. In particular, the vehicle may not start
smoothly when the accelerator pedal
is depressed with the parking brake
applied on an uphill grade. To enable
smooth starting, release the parking
brake before moving the vehicle.
Normal driving:
A position.
Drive with the shift lever in the &
The appropriate gear will be automatically
shifted according to the position of the accelerator pedal, the driving speed and driving
conditions.
.
Passing:
The hill start assist system operates
when the vehicle is accelerating from a
stop on an uphill. (
“Hill Start
Assist System” page 5-38)
adjust vehicle speed.
A position:
. &
Fully depress the accelerator pedal to the floor.
This shifts the transmission down into a lower
gear depending on the vehicle speed. Then
depress the accelerator pedal as needed to
adjust vehicle speed.
M position:
. &
Use the paddle shifter to down shift, then fully
depress the accelerator pedal to the floor. Then
depress the accelerator pedal as needed to
Driving on a downhill:
A position:
. &
The system shifts down according to the degree
of downhills to increase the effectiveness of the
engine brake.
M position:
. &
M
When driving on a long slope, selecting the &
position and 4th or 3rd gear will provide gentle
engine braking.
When driving on a steep downhill, selecting the
M position and 2nd or 1st gear will provide
&
powerful engine braking.
5-22 Starting and driving
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(219,1)
WARNING
.
.
A
When the shift lever is in the &
position, the adaptive shift control
system will stay in a low gear in
order to maintain the effectiveness
of the engine brake. However if the
vehicle is traveling too fast depending on the degree of the slope, you
M position and
should shift to the &
use the paddle shifter to shift down.
If you continue to use only the foot
brake, a high load will be applied to
the brake, which may overheat,
reducing its effectiveness. Be sure
to use the engine brake together
with the foot brake. (
“Adaptive
shift control” page 5-19)
Do not downshift abruptly on slippery roads. This may cause a loss of
control.
19) even on road conditions with continuous and sudden hills or curves.
However, when the transmission oil
temperature is low immediately after
starting the vehicle or high when engaging in high performance driving, there
may be some cases where the system
cannot control shifting. When this ocM position and
curs, switch to the &
select a lower gear, depending on the
gradient of the hill.
When stopping the vehicle
A ↔&
R position
M or &
Leave the shift lever in the &
and firmly depress the foot brake pedal.
If the vehicle will be stopped for a long period of
time, apply the parking brake and move the shift
P or &
N position as necessary.
lever to the &
WARNING
.
Do not race the engine while the
vehicle is stopped. Doing so may
accelerate the vehicle suddenly and
cause an accident when shifting to a
driving gear.
.
While the engine is running, the
propeller shaft that transmits torque
NOTICE
A position, gearWhen driving in the &
shifting will be performed automatically
with the adaptive shift control system
(
“Adaptive shift control” page 5-
from the engine to the transmission
is turning at all times. Crawling or
reaching under the vehicle while the
engine is running may result in
serious injury.
NOTICE
When the vehicle is stopped on a hill,
do not hold the vehicle in place by
depressing the accelerator pedal. Doing
so may cause the clutch to overheat and
result in transmission damage. Use the
brakes to prevent the vehicle from
moving.
When parking the vehicle
WARNING
Follow the instructions below when
parking the vehicle to help prevent the
brake rotor and brake pads from rusting together. Failure to follow the
instructions could cause the rotor and
pads to rust together. If the rotor and
pads rust together, there may be a
popping noise and some vibration
Starting and driving 5-23
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(220,1)
when the vehicle is driven, a wheel may
not roll correctly, or the brake pads
could be damaged. If the pads are
damaged, this may reduce the effectiveness of the brake system which
could cause a collision, serious personal injury or death.
The GT-R uses brake pad materials that have
high metallic content. The brake pad material
helps maintain braking performance in a wide
range of weather and driving conditions.
For the first 3,000 miles (5,000 km) of the
vehicle’s service life, and for the first 3,000 miles
(5,000km) after a brake replacement, the brake
pad to brake rotor clearance is very small. When
parking, apply the parking brake and move the
P position. Idle the engine for
shift lever to the &
more than 20 seconds without depressing the
brake pedal. This allows the brake pads to move
away from the rotor so the pad does not contact
the rotor.
Additionally, the brakes must be dry before
parking the vehicle after driving on wet roads or
after washing the vehicle. If the roads are wet,
lightly apply the brakes for a short distance
before parking the vehicle to dry the brakes.
After washing the vehicle, dry the brakes by
driving on a dry road for a few miles and apply
the brakes normally based on traffic and road
conditions.
The metallic brake pads and brake disc rotor
may rust together when the brakes are not
applied:
.
.
If the vehicle is not idled for 20 seconds
without the brakes applied, or if the brakes
are applied when the vehicle is shut off, the
rotor and pads can rust together, even when
the brake pads are dry.
If the brakes are wet when the vehicle is
parked and the parking brake is applied for a
long time.
Contact a GT-R certified NISSAN dealer if the
brake pads and brake rotor have rusted
together.
1. Bring the vehicle to a complete stop.
2. With the foot brake pedal depressed, apply
the parking brake.
P position.
3. Move the shift lever to the &
4. Check the shift lever position indicator on
P position is
the meter to confirm that the &
selected.
5. Push the ignition switch to stop the engine.
WARNING
Before exiting the vehicle, be sure to
P position
move the shift lever to the &
and stop the engine. If the engine is
running and the shift lever is not in the
P position, the vehicle may start mov&
ing due to partial engagement of the
clutch or to the effects of gravity on a
slope, or the vehicle may suddenly
accelerate due to accidental operation
of the accelerator pedal, possibly causing an accident.
5-24 Starting and driving
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(221,1)
VDC, TRANSMISSION AND
SUSPENSION SETUP SWITCHES
The control of the dual clutch transmission,
Bilstein DampTronic® electronically controlled
shock absorbers and Vehicle Dynamic Control
(VDC) can be changed to the desired modes by
operating the setup switches. Select the desired
mode best suited to the driving conditions.
NOTE:
Bilstein DampTronic® is a registered trademark of ThyssenKrupp Bilstein Suspension GmbH.
1.
2.
3.
Transmission setup switch
Suspension setup switch
Vehicle Dynamic Control (VDC) setup switch
HOW TO SWITCH THE MODES
Each time the engine is started, all switches are
set to the normal mode. The normal mode is
recommended for normal driving. Move the
VDC, transmission and suspension setup
switches up or down to change the mode when
the engine is running.
Starting and driving 5-25
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(222,1)
NOTICE
.
“ESC (Electronic Stability Control)
OFF” indicated on the VDC setup
switch stands for “VDC OFF”.
.
When the ignition switch is pushed
to the “ON” position, the indicators
on the setup switches may illuminate briefly, however this is not a
malfunction.
: Push and hold the switch for longer than
approximately 1 second
: Push the switch
* The selected mode is maintained even if the
A and &
M position.
shift lever is moved between &
5-26 Starting and driving
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(223,1)
FEATURES OF EACH MODE
Transmission
A or &
M.
The transmission mode differs depending on the shift lever position, &
A position:
&
Set up mode
.
.
.
Normal (light is off)
.
.
.
.
.
Features
In addition to the normal mode functions, this mode allows you to achieve higher
engine speed, greater powertrain torque and engine braking.
With the VDC switch in R mode, the R mode start function can be used. (
“R
mode start function” page 5-32)
When the R mode is selected, the maximum speed is lower than the one in the
normal mode.
For everyday and performance driving, an appropriate gear position is automatically
selected.
For long distance driving, this mode helps improve fuel economy by reducing engine
output compared to the normal mode.
The engine response to accelerator operation changes to be less sensitive to pedal
movement than the normal mode. The engine speed does not change as quickly for
small accelerator pedal position changes.
This mode controls powertrain torque on snowy roads and slippery surfaces making
starting and driving easier.
When the SAVE mode is selected, the maximum speed is lower than the one in the
normal mode.
Starting and driving 5-27
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(224,1)
M position:
&
NOTICE
Set up mode
.
.
.
Normal (light is off)
.
.
.
.
.
.
.
Features
This mode allows you to shift gears quickly and directly.
This mode will not allow the transmission to automatically upshift even when the
engine speed reaches the red zone. Do not rev the engine into the red zone.
With the VDC switch in R mode, the R mode start function can be used. (
“R
mode start function” page 5-32)
For everyday and performance driving, any gear position can be selected.
This mode will allow the transmission to automatically upshift even when the engine
speed is about to reach the red zone.
For long distance highway driving, this mode improves fuel economy by reducing
engine output compared to the normal mode.
The engine response to accelerator operation changes to be less sensitive to pedal
movement than the normal mode. The engine speed does not change as quickly for
small accelerator pedal position changes.
This mode controls powertrain torque on snowy roads and slippery surfaces making
starting and driving easier.
This mode allows the transmission to automatically upshift even when the engine
speed is about to reach the red zone.
When the SAVE mode is selected, the maximum speed is lower than the one in the
normal mode.
.
When the engine speed approaches
the red zone, shift to a higher gear
or reduce the engine speed. Operating the engine in the red zone may
cause serious engine damage.
.
Quickest shifting in the R mode with
M position
the transmission in the &
is available when the engine speed
is high. However, the transmission
may shift more slowly when the
engine speed is low.
5-28 Starting and driving
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(225,1)
Suspension
NOTICE
Set up mode
Normal (light is off)
.
.
.
.
Features
The damping force of the shock absorbers is set for maximum vehicle performance.
Riding comfort becomes harder.
The damping force of the shock absorbers is variably adjusted for everyday driving
or maximum vehicle performance.
The damping force of the shock absorbers is variably adjusted for more comfortable
driving. Movement of the vehicle body is larger than the normal and R modes.
While maximizing vehicle performance,
shock absorber control may automatically be returned to the normal mode. If
the R mode or the COMF mode is
selected in the case above, the suspension setup switch indicator may turn off.
Operate the suspension setup switch to
the R mode or the COMF mode and
check to make sure the indicator illuminates. If the indicator does not illuminate, have the system checked by a
GT-R certified NISSAN dealer.
Starting and driving 5-29
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(226,1)
Vehicle Dynamic Control (VDC)
Set up mode
.
.
.
Normal (light is off)
.
Features
In addition to the normal mode function, this mode adjusts front and rear wheel
power distribution to improve handling.
With the transmission switch in R mode, the R mode start function can be used.
“R mode start function” page 5-32)
(
This mode is for use in a broad range of driving conditions, for routine driving during
fair to rainy weather, as well as for driving on road surfaces that are slippery due to
snow or ice.
Make sure to use this mode for everyday driving.
Temporary mode that can be used to free if it is stuck in snow or mud
Also place transmission setup switch in SAVE mode when freeing a stuck vehicle.
WARNING
.
The VDC OFF mode should ONLY be
used briefly to help free the vehicle
if stuck in snow or mud by temporarily stopping operation of the VDC
to maintain wheel torque.
.
Driving the GT-R with the VDC off
may lead to handling issues related
to steering maneuvers, acceleration,
or deceleration. Moreover, driving
with the VDC off can result in an
inoperative vehicle by causing serious damage to the powertrain,
including damage to the Transaxle
Assembly including Transfer, Clutch,
Gears, Transaxle case and all of its
components and other drivetrain
component(s) by overheating or excessive force.
.
Damage to the powertrain or any
drivetrain component(s) that occurs
when there is a record in the Vehicle
Status Data Recorder (VSDR) that
the vehicle was driven with VDC off
during the period when the damage
was incurred is excluded from warranty coverage.
NOTE:
Always make sure the VDC is ON before driving the vehicle by checking that the VDC OFF
indicator lights on the meter and the VDC set-up switch are not illuminated. The GT-R is a
high performance vehicle and the VDC must be on/activated to provide proper powertrain
operation and intended drivability.
5-30 Starting and driving
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(227,1)
TURBOCHARGER SYSTEM
See your 2016 Warranty Information Booklet for
important related information and warranty
coverage exclusions. See also section 2
(
“Transmission warning light” page 2-30)
and section 5 (
“Vehicle Dynamic Control
(VDC) system” page 5-50) of this Owner’s
Manual, “Transmission Clutch Temperature
High” and “Vehicle Dynamic Control (VDC)
System” for important additional related information.
The turbocharger system uses engine oil for
lubrication and cooling of its rotating components. The turbocharger turbine turns at extremely high speeds and it can get very hot. It is
essential to maintain a supply of oil flowing
through the turbocharger system. Therefore, a
sudden interruption of oil supply may cause a
malfunction in the turbocharger.
To ensure prolonged life and performance of the
turbocharger, it is essential to perform the
following maintenance procedure:
.
Change your engine oil according to the
recommended intervals shown in the separate Service and Maintenance Guide. Use
only the recommended engine oil.
.
If the engine had been operating at high
engine speed for an extended period of time,
let it idle for a few minutes prior to shutdown.
.
over a short time, the spark plugs
may become fouled, making the
engine difficult to start. To prevent
diminished starting performance,
avoid starting and stopping the
engine repeatedly during a short
period of time.
NOTE:
. When the vehicle is delivered, the
engine oil level is 0.39 in (10 mm)
below the H mark on the engine oil
dipstick for optimum high performance
driving. The engine oil can be filled up
to the H mark if not engaging in
performance driving.
.
Because of the high performance characteristics of the GT-R engine, more
frequent oil level inspections are necessary. Check the oil level every 1,800
miles (3,000km) and adjust as necessary. Also, change the engine oil based
on the driving conditions. For the
information regarding oil replacement
intervals, refer to the 2016 NISSAN
GT-R Service and Maintenance Guide.
.
Some amount of oil is consumed by
your engine under normal operating
Do not accelerate your engine to high
engine speed immediately after start.
NOTICE
.
This vehicle includes spark plugs
that are designed for high performance. For this reason, if the engine
is repeatedly started and stopped
Starting and driving 5-31
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(228,1)
R MODE START FUNCTION
conditions, and oil consumption by
itself does not necessarily indicate
any malfunction. If your rate of oil
consumption increases suddenly or
without explanation, NISSAN recommends that you have your vehicle
inspected by a GT-R certified NISSAN
dealer.
This function enables the driver to start acceleration from a stop by selecting R mode with the
VDC and transmission setup switch. The engine
output will be maintained at approximately 4,000
rpm. When using the R mode or the R mode
start function, always use proper seating position and follow the safety instructions in Section
1 of this manual.
the engine, transmission and VDC
system, but also the settings of the
suspension and tires. Therefore, any
modification of the vehicle may
disrupt the vehicle’s balance. This
will not only reduce the optimum
performance of the vehicle but may
also cause damage to powertrain
components, including the transmission.
WARNING
.
Failure to follow the warnings and
instruction for the use of this feature may cause a loss of vehicle
control or a collision which may lead
to serious personal injury or death:
.
Make sure to drive carefully within
legal limits.
.
Only use this function when you can
guarantee that it is safe to do so,
based on the surrounding traffic
conditions.
.
Do not use this function on slippery
or wet roads. This may cause loss of
vehicle control and could result in
an accident.
.
The R mode start function has been
developed not only for controlling
NOTICE
.
When the temperature of the engine
coolant and transmission oil is high
or low, the function cannot be used.
The temperature range in which the
R mode start function can be used:
— Engine coolant: 1408F - 2128F
(608C - 1008C)
— Transmission oil: 1408F - 2668F
(608C - 1308C)
.
If the R mode start function is used
4 times consecutively, the function
may be disabled and cannot be
turned on to protect the vehicle
system. While the function is dis-
5-32 Starting and driving
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(229,1)
PARKING BRAKE
abled, the warning light illuminates.
When the warning light illuminates,
perform cool down driving.
(
“Cool down” page GTR-13)
When the warning light turns off,
the function can be used again.
.
The performance of start may vary
depending on the amount of wheel
spin ,or increase and decrease of
the engine output in response to the
outside temperature. (This vehicle
was set up according to the road
surface conditions of the straight
sections of the Sendai Highland
Raceway course in Japan at 598F
(158C).)
.
For safety reasons, VDC control may
activate automatically when driving
on a slippery road surface, such as a
wet road, in order to apply the
brakes or limit the engine output.
.
Frequent use of the R mode start
function increases the load on the
powertrain related parts such as the
clutch and transmission compared
to normal driving. In particular, the
clutch will wear out more quickly.
HOW TO USE R MODE START
FUNCTION
A or &
M position.
1. Move the shift lever to the &
2. Select the R mode with the transmission
setup switch. (
“VDC, transmission and
suspension setup switches” page 5-25)
3. Select the R mode with the VDC setup
switch.
4. Depress the brake pedal firmly with your left
foot and keep depressing the brake pedal.
5. Depress the accelerator pedal quickly to the
floor with your right foot while the brake
pedal is depressed. The engine speed will
increase to approximately 4,000 rpm and
will be maintained.
6. Within 3 seconds after depressing the
accelerator pedal, release the brake pedal.
WARNING
.
Be sure the parking brake is fully
released before driving. Failure to
do so can cause brake failure and
lead to an accident.
.
Do not release the parking brake
from outside the vehicle.
.
Do not use the shift lever in place of
the parking brake. When parking, be
sure the parking brake is fully
engaged.
.
Do not leave children unattended in
Starting and driving 5-33
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(230,1)
CRUISE CONTROL
a vehicle. They could release the
parking brake and cause an accident.
To
To
1.
2.
apply: Pull the parking brake lever up.
release:
Firmly apply the foot brake.
While pulling up on the parking brake lever
A and lower the
slightly, push the button *
lever completely.
3. Before driving, be sure the brake warning
light goes out.
The cruise control allows driving at speeds
above 25 MPH (40 km/h) without keeping your
foot on the accelerator pedal.
WARNING
proaches a gentle uphill, there may be
a slight delay as the vehicle returns to
the preset speed. However, the vehicle
will gradually accelerate and return to
the preset speed.
Do not use the cruise control when
driving under the following conditions.
Doing so could cause a loss of vehicle
control and result in an accident.
.
When it is not possible to keep the
vehicle at a set speed.
.
In heavy traffic or in traffic that
varies in speed.
.
On winding or hilly roads.
.
On slippery roads (rain, snow, ice,
etc.).
.
In very windy areas.
NOTE:
. When the SAVE mode is selected with
the transmission setup switch, the
acceleration and deceleration can be
controlled smoothly. When the SAVE
mode is selected, the maximum setting
speed is lower than the one in the
normal mode. When the vehicle ap-
5-34 Starting and driving
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(231,1)
certified NISSAN dealer.
.
The SET indicator may sometimes blink
when the cruise control main switch is
turned on while pushing the RESUME/
ACCELERATE, SET/COAST or CANCEL
switch. To properly set the cruise control
system, perform the steps below in the order
indicated.
PRECAUTIONS ON CRUISE CONTROL
STEERING-WHEEL-MOUNTED
CONTROLS
.
1.
If the cruise control system malfunctions, it
will cancel automatically. The SET indicator
will blink and the cruise control system
warning will appear to warn the driver.
(
“Cruise control system warning” page
2-40)
.
If the engine coolant temperature becomes
excessively high, the cruise control system
will be canceled automatically.
.
If the SET indicator blinks, turn the cruise
control main switch off and contact a GT-R
2.
3.
4.
MAIN switch
Turns cruise control ON/OFF.
SET/COAST switch (pressed down)
Lowers the set vehicle speed.
RESUME/ACCELERATE switch (pressed up)
Raises the set vehicle speed.
CANCEL switch
Cancels cruise control.
Starting and driving 5-35
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(232,1)
INDICATORS AND DISPLAY
1.
2.
3.
CRUISE display
Displays the set vehicle speed.
CRUISE indicator
Informs the driver that the MAIN switch is ON.
SET indicator
Informs the driver that the vehicle is driving at the
set speed.
CRUISE CONTROL OPERATIONS
Constant-speed driving
To set the cruising speed, perform the following
procedure.
1. Push the MAIN switch on. The CRUISE
indicator will come on.
2. Accelerate your vehicle to the desired
speed, push the SET/COAST switch and
release it. (The SET indicator will illuminate
in the meter.) Take your foot off the
accelerator pedal. Your vehicle will maintain
the set speed.
NOTE:
If the vehicle speed reaches approximately
3 MPH (5 km/h) over the set speed, the set
speed on the vehicle information display
blinks.
5-36 Starting and driving
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(233,1)
down to the desired speed.
Passing another vehicle
To pass another vehicle, depress the accelerator
pedal. When you release the pedal, the vehicle
will return to the previously set speed.
Increasing the set vehicle speed
To reset at a faster cruising speed, use one of
the following methods:
.
Depress the accelerator pedal. When the
vehicle attains the desired speed, push and
release the SET/COAST switch.
.
Push and hold the RESUME/ACCELERATE
switch. When the vehicle attains the speed
you desire, release the switch.
.
Push and then quickly release the RESUME/
ACCELERATE switch. Each time you do
this, the set speed will increase by about 1
MPH or 1 km/h.
Decreasing the set vehicle speed
To reset at a slower cruising speed, use one of
the following methods:
.
Lightly tap the brake pedal. When the
vehicle attains the desired speed, push
and release the SET/COAST switch.
.
Push and hold the SET/COAST switch.
Release the switch when the vehicle slows
.
Push and then quickly release the SET/
COAST switch. Each time you do this, the
set speed will decrease by about 1 MPH or
1 km/h.
Resuming the preset speed
To resume the preset speed, push and release
the RESUME/ACCELERATE switch. The vehicle
will resume the last set cruising speed when the
vehicle speed is over 25 MPH (40 km/h).
Canceling the preset speed
To cancel the preset speed, use one of the
following methods:
1 .
*
.
Push the CANCEL switch
indicator will turn off.
.
Tap the brake pedal
will turn off.
.
2
Turn the MAIN switch *
off. Both the
CRUISE indicator and SET indicator will turn
off.
The SET
3 . The SET indicator
*
Starting and driving 5-37
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(234,1)
HILL START ASSIST SYSTEM
NOTE:
. If cruise control was canceled by pressing the cancel switch or by depressing
the brake pedal, the system changes to
standby status.
.
.
If you depress the brake pedal while
pushing the RESUME/ACCELERATE or
SET/COAST switch and reset at the
cruising speed, the cruise control will
be deactivated. Turn the MAIN switch
off once and then turn it on again.
Under the following conditions, cruise control
will be automatically canceled.
.
Vehicle speed drops to below approximately
19 MPH (30 km/h).
.
Vehicle speed drops to more than approximately 8 MPH (13 km/h) below the set
vehicle speed.
.
The shift lever is moved to a position other
A ↔&
M.
than &
.
VDC operates.
.
A tire is spinning.
.
There is a malfunction in the cruise control
system.
the vehicle from rolling backwards.
Failure to do so may result in a
collision or serious personal injury.
WARNING
.
.
Never rely solely on the hill start
assist system to prevent the vehicle
from moving backward on a hill.
Always drive carefully and attentively. Depress the brake pedal
when the vehicle is stopped on a
steep hill. Be especially careful
when stopped on a hill on frozen
or muddy roads. Failure to prevent
the vehicle from rolling backwards
may result in a loss of control of the
vehicle and possible serious injury
or death.
The hill start assist system is not
designed to hold the vehicle at a
standstill on a hill. Depress the
brake pedal when the vehicle is
stopped on a steep hill. Failure to
do so may cause the vehicle to roll
backwards and may result in a
collision or serious personal injury.
The hill start assist may not prevent
the vehicle from rolling backwards
on a hill under all load or road
conditions. Always be prepared to
depress the brake pedal to prevent
NOTICE
When the vehicle is stopped on a hill,
do not hold the vehicle in place by
depressing the accelerator pedal. Doing
so may cause the clutch to overheat and
result in transmission damage. Use the
brakes to prevent the vehicle from
moving.
The hill start assist system automatically keeps
the brakes applied to help prevent the vehicle
from rolling backwards in the time it takes the
driver to release the brake pedal and apply the
accelerator when the vehicle is stopped on a hill.
Hill start assist will operate automatically under
the following conditions:
.
The shift lever is moved to a forward or
reverse position.
.
The vehicle is stopped completely on a hill
by applying the brake.
The maximum holding time is 2 seconds. After 2
seconds the vehicle will begin to roll back and
5-38 Starting and driving
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(235,1)
BREAK-IN SCHEDULE
.
hill start assist will stop operating completely.
Hill start assist will not operate when the shift
N or &
P position or on a
lever is moved to the &
flat and level road.
NOTICE
Follow these recommendations to obtain maximum engine performance and
ensure the future reliability and economy of your new vehicle. Failure to
follow these recommendations may
result in shortened engine life and
reduced vehicle performance.
NOTE:
This system does not function when the
Vehicle Dynamic Control VDC) system
warning appears on the vehicle information display located in the tachometer.
(
“Vehicle Dynamic Control (VDC) system warning” page 2-37)
Please observe the following types of driving
until the mileage shown below has been
reached.
Until 300 miles (500 km):
.
Do not depress the accelerator pedal more
than halfway and avoid rapid acceleration.
.
Drive with the engine speed kept at less
than 3,500 RPM.
.
Avoid unnecessary quick steering, abrupt
braking and driving on poor roads.
300 to 600 miles (500 to 1,000 km):
.
Avoid rapid acceleration in a low gear (1st to
3rd gears) with the accelerator pedal fully
depressed. Depress the pedal slowly.
.
Avoid unnecessary quick steering and
abrupt braking.
Drive with the suspension setup switch in
the COMF mode to allow more suspension
stroke.
600 to 1,200 miles (1,000 to 2,000 km):
.
Drive with the engine speed kept relatively
M position.
high with the shift lever in the &
Shifting is recommended between 1st and
4th gears.
.
Avoid unnecessary quick steering and
abrupt braking.
.
Drive with the suspension setup switch in
the COMF mode to allow more suspension
stroke.
Even though the mileage reaches over 1,200
miles (2,000 km), the clutch may take longer to
properly engage if the vehicle is mainly driven in
town at a low speed. NISSAN recommends
breaking in the clutch at a GT-R certified
NISSAN dealer.
WHEEL ALIGNMENT
Do not adjust the wheel alignment until the
mileage reaches 1,000 miles (1,600 km). Until
then, the suspension may not engage enough
and the height may be higher.
However, make sure to adjust the alignment
after 1,000 miles (1,600 km).
The wheel alignment can be adjusted by a GT-R
Starting and driving 5-39
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(236,1)
FUEL EFFICIENT DRIVING TIPS
certified NISSAN dealer in accordance with
specifications for city driving to high performance driving.
The tires on the GT-R may have different wear
rates and wear patterns in comparison to
conventional passenger vehicles. Contact a
GT-R certified NISSAN dealer to confirm that
the alignment is within specifications.
Follow these easy-to-use Fuel Efficient Driving
Tips to help you achieve the most fuel economy
from your vehicle.
1. Use smooth accelerator and brake pedal
application.
. Avoid rapid starts and stops.
. Use smooth, gentle accelerator and
brake application whenever possible.
. Maintain constant speed while commuting and coast whenever possible.
2. Maintain constant speed.
. Look ahead to try and anticipate and
minimize stops.
. Synchronizing your speed with traffic
lights allows you to reduce your number
of stops.
. Maintaining a steady speed can minimize
red light stops and improve fuel efficiency.
3. Use air conditioning (A/C) at higher vehicle
speeds.
. Below 40 MPH (64 km/h), it is more
efficient to open windows to cool the
vehicle due to reduced engine load.
. Above 40 MPH (64 km/h), it is more
efficient to use A/C to cool the vehicle
due to increased aerodynamic drag.
. Recirculating the cool air in the cabin
when the A/C is on reduces cooling load.
4. Drive at economical speeds and distances.
. Observing the speed limit and not
exceeding 60 MPH (97 km/h) (where
legally allowed) can improve fuel efficiency due to reduced aerodynamic
drag.
. Maintaining a safe following distance
behind other vehicles reduces unnecessary braking.
. Safely monitoring traffic to anticipate
changes in speed permits reduced braking and smooth acceleration changes.
. Select a gear range suitable to road
conditions.
5. Use cruise control.
. Using cruise control during highway
driving helps maintain a steady speed.
. Cruise control is particularly effective in
providing fuel savings when driving on
flat terrains.
6. Plan for the shortest route.
. Utilize a map or navigation system to
determine the best route to save time.
7. Avoid idling.
. Shutting off your engine when safe for
stops exceeding 30-60 seconds saves
fuel and reduces emissions.
5-40 Starting and driving
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(237,1)
INCREASING FUEL ECONOMY
8. Buy an automated pass for toll roads.
. Automated passes permit drivers to use
special lanes to maintain cruising speed
through the toll and avoid stopping and
starting.
9. Winter warm up.
. Limit idling time to minimize impact to
fuel economy.
. Vehicles typically need no more than 30
seconds of idling at start-up to effectively
circulate the engine oil before driving.
. Your vehicle will reach its ideal operating
temperature more quickly while driving
versus idling.
.
Keep your engine tuned up.
.
Follow the recommended scheduled maintenance.
.
Keep the tires inflated to the correct
pressure. Low tire pressure increases tire
wear and lowers fuel economy.
.
Keep the wheels in correct alignment.
Improper alignment increases tire wear and
lowers fuel economy.
.
Use the recommended viscosity engine oil.
(
“Oil viscosity” page 9-6)
ALL-WHEEL DRIVE (AWD)
10. Keeping your vehicle cool.
. Park your vehicle in a covered parking
area or in the shade whenever possible.
. When entering a hot vehicle, opening the
windows will help to reduce the inside
temperature faster, resulting in reduced
demand on your A/C system.
AWD WARNING LIGHT
The AWD warning light is located in the meter.
The AWD warning light comes on when the
ignition switch is pushed to the ON position. It
turns off soon after the engine is started.
Starting and driving 5-41
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(238,1)
If any malfunction occurs in the AWD system
while the engine is running, the warning light will
come on.
The warning light may blink rapidly (about twice
per second) while trying to free a stuck vehicle
due to high AWD clutch temperature. The
driving mode may change to two-wheel drive.
If the warning light blinks rapidly during operation, stop the vehicle with the engine idling in a
safe place immediately. Then if the light goes off
after a while, you can continue driving.
A large difference between the diameters of
front and rear wheels will make the warning light
blink slowly (about once per two seconds). Pull
off the road in a safe area, and idle the engine.
Check that all tire sizes are the same, tire
pressure is correct and tires are not worn and
winter tires are not installed on the front or rear
wheels only.
If the warning light is blinking after the above
operation, have your vehicle checked by a GT-R
certified NISSAN dealer as soon as possible.
If non-genuine GT-R tires are used, the warning
light may illuminate. (
“GT-R special precautions” page GTR-5)
NOTICE
WARNING
.
.
Do not attempt to raise two wheels
off the ground and shift the transmission to any drive or reverse
position with the engine running.
Doing so may result in drivetrain
damage or unexpected vehicle
movement which could result in
serious vehicle damage or personal
injury.
Do not attempt to test an AWD
equipped vehicle on a 2-wheel dynamometer (such as the dynamometers used by some states for
emissions testing) or similar equipment even if the other two wheels
are raised off the ground. Make sure
that you inform the test facility
personnel that your vehicle is
equipped with AWD before it is
placed on a dynamometer. Using
the wrong test equipment may result in drivetrain damage or unexpected vehicle movement which
could result in serious vehicle damage or personal injury.
.
If the warning light comes on while
driving there may be a malfunction
in the AWD system. Reduce the
vehicle speed and have your vehicle
checked by a GT-R certified NISSAN
dealer as soon as possible.
.
If the warning light remains on after
the above operation, have your
vehicle checked by a GT-R certified
NISSAN dealer as soon as possible.
.
The powertrain may be damaged if
you continue driving with the warning light blinking.
.
Do not spin the rear wheels while
driving. Spinning the rear wheels
may increase the temperatures of
the AWD clutch system and damage
the system. Adjust the accelerator
pedal position to stop wheel spin.
5-42 Starting and driving
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(239,1)
TIGHT CORNER BRAKING PHENOMENON
If the steering wheel is turned more than half a
turn when the vehicle is started when it is cold, it
may be harder to move the vehicle forward and
backward. This phenomenon is known as the
“tight corner braking phenomenon”.
This phenomenon is unique to AWD vehicles,
and occurs due to a difference in speeds
between the front and rear wheels while the
vehicle is turning. This does not indicate that
there is a malfunction.
NOTE:
If the tight corner braking phenomenon
occurs, a slipping sound may be heard
from the tires, or a squeaking sound may
be heard from the drive system.
Reducing tight corner braking phenomenon
The tight corner braking phenomenon can be
temporarily reduced.
Push the transmission setup switch down for
approximately 4 seconds while the engine is
running.
.
The SAVE mode indicator will blink once
and will then turn off.
.
If the SAVE mode is already selected, the
SAVE mode indicator will blink once and
then illuminate again. (
“VDC, transmission and suspension setup switches” page
5-25)
After performing the above, the vehicle switches
from the AWD mode to 2WD mode only if both
of the following conditions are met:
.
Vehicle speed is less than approximately 6
A AND
MPH (10 km/h) *
.
The steering wheel is turned more than 1/2
B .
turn *
If the above driving conditions are not met,
the vehicle will not switch to the 2WD
mode to temporarily reduce the braking
phenomenon even if the transmission
setup switch is operated.
To stop reducing the phenomenon, push the
transmission setup switch down for approxiStarting and driving 5-43
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(240,1)
mately 4 seconds again. The driving mode will
switch to the normal AWD mode.
Reduction of the tight corner braking phenomenon will be cancelled when:
.
the R mode is selected with the transmission
setup switch
.
the SAVE mode is selected with the
transmission setup switch and the OFF
mode is selected with the VDC setup switch
.
the ignition switch is pushed to the "OFF"
position
.
the R mode start function is used
WARNING
Do not reduce the tight corner braking
phenomenon when driving on a road
surface that is slippery or covered in
snow, because the driving mode will
switch to 2WD. This may cause tire
slipping and may cause a loss of control
and result in a collision, personal injury
or death.
TIRES
This vehicle is equipped with special tires. When
changing the tires, install the designated special
tires. Replacing tires as a set of four with new
ones is recommended. However, if a tire is
punctured or damaged, it may be possible to
replace only the damaged tire. Determining
whether one tire or a complete set of tires
should be replaced is based on a number of
factors including tire wear and condition. Contact your GT-R certified NISSAN dealer. They
can recommend if an individual tire or a
complete set should be replaced.
Electronic control continuously distributes torque to the front and rear wheels in the range
from 0:100 (rear-wheel drive mode) to 50:50
(all-wheel drive mode) to match the driving
conditions and road conditions. This allows the
engine output (torque) to be effectively transmitted to the road surface.
NOTICE
If tires other than the designated tires,
tires with large differences in wear or
tires of different sizes are installed, the
AWD performance will be degraded and
the drive mechanism may be damaged.
AWD SYSTEM CHARACTERISTICS
The AWD system automatically distributes the
optimal torque to the front and rear wheels. This
provides both the superior turning performance
of a rear wheel drive vehicle and the traction of a
AWD vehicle.
5-44 Starting and driving
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(241,1)
LIMITED SLIP DIFFERENTIAL (LSD)
The rear final drive of this vehicle is equipped
with a 1.5-way mechanical Limited Slip Differential (LSD).
does not indicate that there is a malfunction.
.
The LSD controls the speed difference
between the left and right wheels, and
optimally allocates torque to the
wheels.
.
The 1.5-way mechanical LSD in the rear
final drive of this vehicle is characterized by its asymmetrical LSD effects
when the accelerator pedal is ON and
when it is OFF. This allows the appropriate amount of torque for the driving
environment to be transmitted to the
road surface.
WARNING
Sudden operation of the accelerator
pedal can result in fishtailing or sideslip, possibly causing an accident. Use
particular caution when driving in rainy
weather or on slippery roads.
NOTICE
Use the designated differential gear oil.
If any oil other than the designated oil
is used, the LSD may not operate
correctly, and noise and vibration may
occur, possibly resulting in a malfunction.
NOTE:
. If the vehicle accelerates from a stop
with the steering wheel turned in cold
temperatures, the inner wheel tire may
slip and some noise or vibration may
be heard. This phenomenon is unique
to vehicles equipped with the LSD. This
Starting and driving 5-45
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(242,1)
PARKING/PARKING ON HILLS
parking the vehicle to help prevent
the brake rotor and brake pads from
rusting together. Failure to follow
the instructions could cause the
rotor and pads to rust together. If
the rotor and pads rust together,
there may be a popping noise and
some vibration when the vehicle is
driven, a wheel may not roll correctly, or the brake pads could be
damaged. If the pads are damaged,
this may reduce the effectiveness of
the brake system which could cause
a collision, serious personal injury
or death.
dents.
WARNING
.
.
Do not stop or park the vehicle over
flammable materials such as dry
grass, waste paper or rags. They
may ignite and cause a fire.
.
Never leave the engine running
while the vehicle is unattended.
.
Do not leave children unattended
inside the vehicle. They could unknowingly activate switches or controls. Unattended children could
become involved in serious acci-
Safe parking procedures require
that both the parking brake be
applied and the transmission placed
P position. Failure to do so
into the &
could cause the vehicle to move
unexpectedly or roll away and result
in an accident.
.
Make sure the shift lever has been
pushed as far forward as it can go
and cannot be moved without depressing the foot brake pedal.
.
Follow the instructions below when
1. Firmly apply the parking brake.
P position.
2. Move the shift lever to the &
3. To help prevent the vehicle from rolling into
the street when parked on a sloping drive
way, it is a good practice to turn the wheels
as illustrated.
. HEADED DOWNHILL WITH CURB: *
1
Turn the wheels into the curb and move
the vehicle forward until the curb side
wheel gently touches the curb.
. HEADED UPHILL WITH CURB: *
2
Turn the wheels away from the curb and
move the vehicle back until the curb side
5-46 Starting and driving
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(243,1)
POWER STEERING
.
wheel gently touches the curb.
HEADED UPHILL OR DOWNHILL, NO
3
CURB: *
Turn the wheels toward the side of the
road so the vehicle will move away from
the center of the road if it moves.
4. Push the ignition switch to the LOCK
position.
The GT-R uses brake pad materials that have
high metallic content. The brake pad material
helps maintain braking performance in a wide
range of weather and driving conditions.
For the first 3,000 - 6,000 miles (5,000 10,000 km) of the vehicle’s service life, and for
the first 3,000 - 6,000 miles (5,000 - 10,000
km) after a brake replacement, the brake pad to
brake rotor clearance is very small. When
parking, apply the parking brake and move the
P position. Idle the engine for
shift lever to the &
more than 20 seconds without depressing the
brake pedal. This allows the brake pads to move
away from the rotor so the pad does not contact
the rotor.
driving on a dry road for a few miles and apply
the brakes normally based on traffic and road
conditions.
The metallic brake pads and brake disc rotor
may rust together when the brakes are not
applied:
.
.
If the vehicle is not idled for 20 seconds
without the brakes applied, or if the brakes
are applied when the vehicle is shut off, the
rotor and pads can rust together, even when
the brake pads are dry.
If the brakes are wet when the vehicle is
parked and the parking brake is applied for a
long time.
Contact a GT-R certified NISSAN dealer if the
brake pads and brake rotor have rusted
together.
WARNING
If the engine is not running or is turned
off while driving, the power assist for
the steering will not work. Steering will
be harder to operate.
The power assisted steering uses a hydraulic
pump, driven by the engine, to assist steering.
If the engine stops or the drive belt breaks, you
will still have control of the vehicle. However,
much greater steering effort is needed, especially in sharp turns and at low speeds.
Additionally, the brakes must be dry before
parking the vehicle after driving on wet roads or
after washing the vehicle. If the roads are wet,
lightly apply the brakes for a short distance
before parking the vehicle to dry the brakes.
After washing the vehicle, dry the brakes by
Starting and driving 5-47
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(244,1)
BRAKE SYSTEM
BRAKING PRECAUTIONS
Using the brakes
PARKING BRAKE BREAK-IN
The brake system has two separate hydraulic
circuits. If one circuit malfunctions, you will still
have braking at two wheels.
Avoid resting your foot on the brake pedal while
driving. This will cause overheating of the
brakes, wearing out the brake and pads faster
and reduce gas mileage.
Break in the parking brake shoes whenever the
stopping effect of the parking brake is weakened
or whenever the parking brake shoes and/or
drums/rotors are replaced, in order to assure the
best braking performance.
You may feel a small click and hear a sound
when the brake pedal is fully depressed slowly.
This is not a malfunction and indicates that the
brake assist mechanism is operating properly.
Vacuum assisted brakes
The brake booster aids braking by using engine
vacuum. If the engine stops, you can stop the
vehicle by depressing the brake pedal. However,
greater foot pressure on the brake pedal will be
required to stop the vehicle and the stopping
distance will be longer.
To help reduce brake wear and to prevent the
brakes from overheating, reduce speed and
downshift to a lower gear before going down a
slope or long grade. Overheated brakes may
reduce braking performance and could result in
loss of vehicle control.
WARNING
.
While driving on a slippery surface,
be careful when braking, accelerating or downshifting. Abrupt braking
or accelerating could cause the
wheels to skid and result in an
accident.
.
If the engine is not running or is
turned off while driving, the power
assist for the brakes will not work.
Braking will be harder.
Wet brakes
When the vehicle is washed or driven through
water, the brakes may get wet. As a result, your
braking distance will be longer and the vehicle
may pull to one side during braking.
To dry brakes, drive the vehicle at a safe speed
while lightly tapping the brake pedal to heat-up
the brakes. Do this until the brakes return to
normal. Avoid driving the vehicle at high speeds
until the brakes function correctly.
This procedure is described in the vehicle
service manual and can be performed by a
GT-R certified NISSAN dealer.
5-48 Starting and driving
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(245,1)
BRAKE ASSIST
ANTI-LOCK BRAKING SYSTEM
(ABS)
WARNING
.
.
The Anti-lock Braking System (ABS)
is a sophisticated device, but it
cannot prevent accidents resulting
from careless or dangerous driving
techniques. It can help maintain
vehicle control during braking on
slippery surfaces. Remember that
stopping distances on slippery surfaces will be longer than on normal
surfaces even with ABS. Stopping
distances may also be longer on
rough, gravel or snow covered
roads, or if you are using tire chains.
Always maintain a safe distance
from the vehicle in front of you.
Ultimately, the driver is responsible
for safety.
Tire type and condition may also
affect braking effectiveness. When
replacing tires, install the specified
size of tires on all four wheels.
The Anti-lock Braking System (ABS) controls
the brakes so the wheels do not lock during hard
braking or when braking on slippery surfaces.
The system detects the rotation speed at each
wheel and varies the brake fluid pressure to
prevent each wheel from locking and sliding. By
preventing each wheel from locking, the system
helps the driver maintain steering control and
helps to minimize swerving and spinning on
slippery surfaces.
Using the system
Depress the brake pedal and hold it down.
Depress the brake pedal with firm steady
pressure, but do not pump the brakes. The
ABS will operate to prevent the wheels from
locking up. Steer the vehicle to avoid obstacles.
WARNING
Do not pump the brake pedal. Doing so
may result in increased stopping distances.
Self-test feature
The ABS includes electronic sensors, electric
pumps, hydraulic solenoids and a computer. The
computer has a built-in diagnostic feature that
tests the system each time you start the engine
and move the vehicle at a low speed in forward
or reverse. When the self-test occurs, you may
hear a “clunk” noise and/or feel a pulsation in the
brake pedal. This does not indicate that there is
a malfunction. If the computer senses a malfunction, it switches the ABS off and illuminates
the ABS warning light on the meter. The brake
system then operates normally, but without antilock assistance.
If the ABS warning light illuminates during the
self-test or while driving, have the vehicle
checked by a GT-R certified NISSAN dealer.
Normal operation
The ABS operates at speeds above 3 to 6 MPH
(5 to 10 km/h). The speed varies according to
road conditions.
When the ABS senses that one or more wheels
are close to locking up, the actuator rapidly
applies and releases hydraulic pressure. This
action is similar to pumping the brakes very
quickly. You may feel a pulsation in the brake
pedal and hear a noise from under the hood or
feel a vibration from the actuator when it is
operating. This is normal and indicates that the
ABS is operating properly. However, the pulsation may indicate that road conditions are
hazardous and extra care is required while
driving.
Starting and driving 5-49
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(246,1)
VEHICLE DYNAMIC CONTROL (VDC)
SYSTEM
The Vehicle Dynamic Control (VDC) system
uses various sensors to monitor driver inputs
and vehicle motion. Under certain driving conditions, the VDC system helps to perform the
following functions.
.
.
Controls brake pressure to reduce wheel
slip on one slipping drive wheel so power is
transferred to a non slipping drive wheel on
the same axle.
Controls brake pressure and engine output
to reduce drive wheel slip based on vehicle
speed (traction control function).
.
Controls brake pressure at individual wheels
and engine output to help the driver maintain
control of the vehicle in the following
conditions:
— understeer (vehicle tends to not follow
the steered path despite increased
steering input)
— oversteer (vehicle tends to spin due to
certain road or driving conditions).
The VDC system can help the driver to maintain
control of the vehicle, but it cannot prevent loss
of vehicle control in all driving situations.
When the VDC system operates, the VDC
warning light
in the meter flashes so note
the following:
.
The road may be slippery or the system may
determine some action is required to help
keep the vehicle on the steered path.
.
You may feel a pulsation in the brake pedal
and hear a noise or vibration from under the
hood. This is normal and indicates that the
VDC system is working properly.
.
Adjust your speed and driving to the road
conditions.
.
The VDC mode can be changed using the
VDC setup switch. (
“VDC, transmission and suspension setup switches” page
5-25)
(
“Vehicle Dynamic Control (VDC) warning
light” page 2-31,
“Vehicle Dynamic Control (VDC) off indicator light” page 2-32)
If a malfunction occurs in the system, the VDC
warning light
illuminates in the meter. The
VDC system automatically turns off.
The VDC setup switch is used to turn off the
VDC system. The VDC off indicator
illuminates to indicate the VDC system is off.
When the VDC setup switch is used to turn off
the system, the VDC system still operates to
prevent one drive wheel from slipping by
transferring power to a non slipping drive wheel.
The VDC warning light
flashes if this
occurs. All other VDC functions are off and the
VDC warning light
will not flash. The VDC
system is automatically reset to on when the
ignition switch is placed in the off position then
back to the on position.
(
“Vehicle Dynamic Control (VDC) warning
light” page 2-31,
“Vehicle Dynamic Control (VDC) off indicator light” page 2-32)
The computer has a built-in diagnostic feature
that tests the system each time you start the
engine and move the vehicle forward or in
reverse at a slow speed. When the self-test
occurs, you may hear a “clunk” noise and/or feel
a pulsation in the brake pedal. This is normal and
is not an indication of a malfunction.
WARNING
.
The VDC system is designed to help
the driver maintain stability but
does not prevent accidents due to
abrupt steering operation at high
speeds or by careless or dangerous
driving techniques. Reduce vehicle
speed and be especially careful
when driving and cornering on slippery surfaces and always drive carefully.
.
Do not modify the vehicle’s suspension. If suspension parts such as
5-50 Starting and driving
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(247,1)
shock absorbers, struts, springs,
stabilizer bars, bushings and
wheels are not NISSAN approved
or are extremely deteriorated, the
VDC system may not operate properly. This could adversely affect
vehicle handling performance, and
the VDC warning light
may
illuminate.
.
If brake related parts such as brake
pads, rotors and calipers are not
standard equipment or are extremely deteriorated, the VDC system
may not operate properly and the
VDC warning light
may illuminate.
.
If engine control related parts are
not standard equipment or are extremely deteriorated, the VDC warning light
may illuminate.
.
When driving on extremely inclined
surfaces such as higher banked
corners, the VDC system may not
operate properly and the VDC warning light
may illuminate. Do not
drive on these types of roads.
.
When driving on an unstable surface such as a turntable, ferry,
elevator or ramp, the VDC warning
light
may illuminate. This is not
a malfunction. Restart the engine
after driving onto a stable surface.
.
.
If wheels or tires other than the
those recommended are used, the
VDC system may not operate properly and the VDC warning light
may illuminate.
WARNING
.
The VDC OFF mode should ONLY be
used briefly to help free the vehicle
if stuck in snow or mud by temporarily stopping operation of the VDC
to maintain wheel torque.
.
Driving the GT-R with the VDC off
may lead to handling issues related
to steering maneuvers, acceleration,
or deceleration. Moreover, driving
with the VDC off can result in an
inoperative vehicle by causing serious damage to the powertrain,
including damage to the Transaxle
Assembly including Transfer, Clutch,
Gears, Transaxle case and all of its
components and other drivetrain
component(s) by overheating or excessive force.
.
Damage to the powertrain or any
drivetrain component(s) that occurs
when there is a record in the Vehicle
Status Data Recorder (VSDR) that
the vehicle was driven with VDC off
during the period when the damage
was incurred is excluded from warranty coverage.
The VDC system is not a substitute
for winter tires or tire chains on a
snow covered road.
NOTE:
. Always make sure the VDC is ON
before driving the vehicle by checking
that the VDC OFF indicator lights on
the meter and the VDC set-up switch
are not illuminated.
The GT-R is a high performance vehicle
and the VDC must be on/activated to
provide proper powertrain operation
and intended drivability.
Starting and driving 5-51
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(248,1)
COLD WEATHER DRIVING
See your 2016 Warranty Information Booklet for
important related information and warranty
coverage exclusions. See also section 2
(
“Transmission warning light” page 2-30)
and section 5 (
“Vehicle Dynamic Control
(VDC) system” page 5-50) of this Owner’s
Manual, “Transmission Clutch Temperature
High” and “Vehicle Dynamic Control (VDC)
System” for important additional related information.
.
.
Except for the emergency cases above,
any issues related to driving stability
(e.g., steering maneuvers and maneuvers during acceleration and deceleration) and any damages to drivetrain
components (e.g., transfer, clutch, a
sort of gear, transaxle case) will not
be covered by warranty if there is a
record in the Vehicle Status Data
Recorder (VSDR) that the vehicle was
driven with VDC off.
When attempting to free the vehicle
from mud or fresh snow, the VDC will
detect the tire slipping, and the engine
speed may not increase even when the
accelerator pedal is depressed. To raise
the engine speed, use the VDC set up
switch to turn the VDC system OFF and
select SAVE mode with the transmis-
sion switch. (
“VDC, transmission
and suspension setup switches” page
5-25)
.
When the VDC system is turned OFF,
all VDC functions (including traction
control), except for the ABS functions,
are deactivated.
FREEING A FROZEN DOOR LOCK
To prevent a door lock from freezing, apply
deicer through the key hole. If the lock becomes
frozen, heat the key before inserting it into the
key hole or use the Intelligent Key system.
ANTI-FREEZE
In the winter when it is anticipated that the
outside temperature will drop below 328F (08C),
check antifreeze to assure proper winter protection. (
“Engine cooling system” page 8-10)
BATTERY
If the battery is not fully charged during
extremely cold weather conditions, the battery
fluid may freeze and damage the battery. To
maintain maximum efficiency, the battery should
be checked regularly. (
“Battery” page 817)
DRAINING OF COOLANT WATER
If the vehicle is to be left outside without
antifreeze, drain the cooling system, including
the engine block. Refill before operating the
vehicle. For details, contact a GT-R certified
NISSAN dealer.
5-52 Starting and driving
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(249,1)
TIRE EQUIPMENT
SPECIAL WINTER EQUIPMENT
The GT-R summer tires are made from a
specially formulated rubber to maximize the
vehicle’s performance capabilities. Performance
of summer tires is substantially reduced when
temperatures are less than 328F (08C) so you
must drive carefully. NISSAN recommends the
use of winter or all-season tires on all four
wheels if you plan to operate your vehicle in
snowy or icy conditions when temperatures are
less than 328F (08C).
It is recommended that the following items be
carried in the vehicle during winter:
WARNING
Never use summer tires when the
temperature is below −48F (−208C) to
prevent permanent tread deformation
which may cause tire damage or tire
failure. This may cause a loss of vehicle
control which can result in serious
personal injury or death.
Tire chains may be used. (
“Tire chains”
page 8-40)
If you install tires, they must also be the specified
size, brand, construction and tread pattern on all
four wheels.
.
A scraper and stiff-bristled brush to remove
ice and snow from the windows and wiper
blades.
.
A sturdy, flat board to be placed under the
jack to give it firm support.
.
A shovel to dig the vehicle out of snowdrifts.
.
Extra window washer fluid to refill the
reservoir tank.
.
Allow more stopping distance under
these conditions. Braking should be
started sooner than on dry pavement.
.
Allow greater following distances
on slippery roads.
.
Watch for slippery spots (glare ice).
These may appear on an otherwise
clear road in shaded areas. If a
patch of ice is seen ahead, brake
before reaching it. Try not to brake
while on the ice, and avoid any
sudden steering maneuvers.
.
Do not use the cruise control on
slippery roads.
.
Snow can trap dangerous exhaust
gases under your vehicle. Keep
snow clear of the exhaust pipe and
from around your vehicle.
DRIVING ON SNOW OR ICE
WARNING
.
.
Wet ice (328F, 08C and freezing rain),
very cold snow or ice can be slick
and very hard to drive on. The
vehicle will have much less traction
or “grip” under these conditions. Try
to avoid driving on wet ice until the
road is salted or sanded.
Whatever the condition, drive with
caution. Accelerate and slow down
with care. If accelerating or downshifting too fast, the drive wheels
will lose even more traction.
NOTE:
When driving on snow, select the SAVE
mode with the setup switch. By selecting
the SAVE mode, the engine output is
controlled appropriately for snow or slippery road surfaces. This enables the vehicle to start or accelerate smoothly.
Starting and driving 5-53
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(250,1)
ACTIVE NOISE CONTROL (if so
equipped)
ENGINE BLOCK HEATER (if so
equipped)
Engine block heaters are used to assist with
cold temperature starting.
The engine block heater should be used when
the outside temperature is 208F (−78C) or lower.
WARNING
.
Do not use your engine block heater
with an ungrounded electrical system or a 2-pronged adapter. You can
be seriously injured by an electrical
shock if you use an ungrounded
connection.
.
Disconnect and properly store the
engine block heater cord before
starting the engine. Damage to the
cord could result in an electrical
shock and can cause serious injury.
.
Use a heavy-duty 3-wire, 3-pronged
extension cord rated for at least
10A. Plug the extension cord into a
Ground Fault Interrupt (GFI) protected, grounded 110-VAC outlet.
To use the engine block heater
1. Turn the engine off.
2. Plug the engine block heater cord into a
grounded 3-wire, 3-pronged extension cord.
3. Plug the extension cord into a Ground Fault
Interrupt (GFI) protected, grounded 110volt AC (VAC) outlet.
4. The engine block heater must be plugged in
for at least 2 - 4 hours, depending on
outside temperatures, to properly warm the
engine coolant. Use an appropriate timer to
turn the engine block heater on.
5. Before starting the engine, unplug and
properly store the cord to keep it away from
moving parts.
Failure to use the proper extension
cord or a grounded outlet can result
in a fire or electrical shock and
cause serious personal injury.
5-54 Starting and driving
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(251,1)
This system uses the front and rear microphones
1 to detect engine booming noise. The system
*
then automatically generates a noise cancelling
2 and woofer *
3
sound through the speakers *
to reduce engine booming noise.
1 are located
The front and rear microphones *
inside of the roof.
The front speakers are located on the doors and
the woofer is located in between the rear seats.
NOTE:
To operate the active noise control properly:
. Do not cover the speakers or woofer.
.
Do not cover the microphones.
.
Do not change or modify speakers including
the woofer and any audio related parts such
as the amplifier.
.
Do not make any modification including
sound deadening or modifications around
the microphones, speakers or woofer.
Starting and driving 5-55
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(252,1)
MEMO
5-56 Starting and driving
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(253,1)
6 In case of emergency
Hazard warning flasher switch .............................................
Roadside assistance program ..............................................
Emergency engine shut off ....................................................
Flat tire ........................................................................................
Tire Pressure Monitoring System (TPMS) ...................
Run-flat tires ........................................................................
6-2
6-2
6-3
6-3
6-3
6-4
Jump starting ............................................................................ 6-5
Push starting ............................................................................. 6-7
If your vehicle overheats ........................................................ 6-8
Towing your vehicle ................................................................ 6-9
Towing recommended by NISSAN ............................. 6-9
Vehicle recovery (freeing a stuck vehicle) .............. 6-10
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(254,1)
HAZARD WARNING FLASHER
SWITCH
ROADSIDE ASSISTANCE
PROGRAM
WARNING
Push the switch on to warn other drivers when
you must stop or park under emergency conditions. All turn signal lights will flash.
The flasher can be actuated with the ignition
switch in any position.
Some state laws may prohibit the use of
the hazard warning flasher switch while
driving.
6-2
.
If stopping for an emergency, be
sure to move the vehicle well off the
road.
.
Do not use the hazard warning
flashers while moving on the highway unless unusual circumstances
force you to drive so slowly that
your vehicle might become a hazard
to other traffic.
.
Turn signals do not work when the
hazard warning flasher lights are
on.
In the event of a roadside emergency, Roadside
Assistance Service is available to you. Please
refer to your Warranty Information Booklet (U.S.)
or Warranty & Roadside Assistance Information
Booklet (Canada) for details.
In case of emergency
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(255,1)
EMERGENCY ENGINE SHUT OFF
FLAT TIRE
To shut off the engine in an emergency situation
while driving, perform the following procedure:
TIRE PRESSURE MONITORING
SYSTEM (TPMS)
.
Rapidly push the push-button ignition switch
3 consecutive times in less than 1.5
seconds, or
.
Push and hold the push-button ignition
switch for more than 2 seconds.
This vehicle is equipped with the Tire Pressure
Monitoring System (TPMS). It monitors tire
pressure of all tires. When the low tire pressure
warning light is lit, one or more of your tires is
significantly under-inflated. If the vehicle is being
driven with low tire pressure, the TPMS will
activate and warn you of it by the low tire
pressure warning light (in the meter) or the
warning message (on the display). This system
will activate only when the vehicle is driven at
speeds above 16 MPH (25 km/h). (
“Low
tire pressure warning light” page 2-27)
(
“Tire Pressure Monitoring System
(TPMS)” page 5-4)
could occur and may lead to an
accident and could result in serious
personal injury. Check the tire pressure for all four tires. Adjust the tire
pressure to the recommended COLD
tire pressure shown on the Tire and
Loading Information label to turn
the low tire pressure warning light
off. If the light still illuminates while
driving after adjusting the tire pressure, a tire may be flat.
.
When a wheel is replaced, the TPMS
will not function and the low tire
pressure warning light will flash for
approximately 1 minute. The light
will remain on after 1 minute. Contact a GT-R certified NISSAN dealer
as soon as possible for tire replacement and/or system resetting.
.
Replacing tires with those not originally specified by NISSAN could
affect the proper operation of the
TPMS.
.
Do not inject any tire liquid or
aerosol tire sealant into the tires,
as this may cause a malfunction of
the tire pressure sensors.
WARNING
.
If the low tire pressure warning light
illuminates while driving, avoid sudden steering maneuvers or abrupt
braking, reduce vehicle speed, pull
off the road to a safe location and
stop the vehicle as soon as possible. Driving with under-inflated tires
may permanently damage the tires
and increase the likelihood of tire
failure. Serious vehicle damage
In case of emergency 6-3
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(256,1)
NOTE:
. You can check the pressure of all four
tires on the multi function display. See
the separate Multi Function Display
Owner’s Manual.
.
.
The tires of this vehicle are filled with
nitrogen gas. When the tire pressure is
low, fill the tires with nitrogen. Contact
a GT-R certified NISSAN dealer for
information on filling the tires with
nitrogen.
Run-flat tires are those tires that can be used
temporarily if they are punctured. (
“Run-flat
tires” page 8-39)
Also, see the tire safety information in the
Warranty Information Booklet.
6-4
.
.
If nitrogen is not available, compressed
air may be safely used under normal
driving conditions. However, NISSAN
recommends refilling with nitrogen for
maximum tire performance.
RUN-FLAT TIRES
NOTICE
WARNING
.
Although you can continue driving
with a punctured run-flat tire, remember that vehicle handling stability is reduced, which could lead to
an accident and personal injury.
Also, driving a long distance at high
speeds may damage the tires.
.
Never install tire chains on a punctured run-flat tire, as this could
damage your vehicle.
.
Avoid driving over any projection or
pothole, as the clearance between
the vehicle and the ground is smaller than normal.
Do not drive at speeds above 50
MPH (80 km/h) and do not drive
more than 50 miles (80 km) with a
punctured run-flat tire. The actual
distance the vehicle can be driven
on a flat tire depends on outside
temperature, vehicle load, road conditions and other factors.
.
Do not enter an automated car wash
with a punctured run-flat tire.
.
Have the punctured tire replaced by
your GT-R certified NISSAN dealer
as soon as possible, as the tire’s
performance capability is reduced.
Drive safely at reduced speeds.
Avoid hard cornering or braking,
which may cause you to lose control
of the vehicle.
If you have a flat tire and have to stop the
vehicle, follow the instructions below.
1. Safely move the vehicle off the road and
away from traffic.
2. Turn on the hazard warning flashers.
3. Park on a level surface and apply the parking
P position.
brake. Move the shift lever to the &
4. Turn off the engine.
5. Raise the hood to warn other traffic, and to
signal professional road assistance personnel that you need assistance.
In case of emergency
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(257,1)
JUMP STARTING
6. Have all passengers get out of the vehicle
and stand in a safe place, away from traffic
and clear of the vehicle.
For the tire removing procedure, see the
following section. (
“Jacking vehicle and
removing wheels” page 8-43)
The following circumstances indicate that the
battery is discharged.
.
The starter motor does not turn or it turns
weakly and the engine does not start.
.
The vehicle lights are much dimmer than
usual.
.
The sound of the horn is weak. The horn
makes no sound.
WARNING
.
If done incorrectly, jump starting
can lead to a battery explosion,
resulting in severe injury or death.
It could also damage your vehicle.
.
Explosive hydrogen gas is always
present in the vicinity of the battery.
Keep all sparks and flames away
from the battery.
.
Do not allow battery fluid to come
into contact with eyes, skin, clothing
or painted surfaces. Battery fluid is
a corrosive sulphuric acid solution
which can cause severe burns. If the
fluid should come into contact with
anything, immediately flush the contacted area with water.
.
Keep the battery out of the reach of
children.
.
The booster battery must be rated at
12 volts. Use of an improperly rated
battery can damage your vehicle.
.
Whenever working on or near a
battery, always wear suitable eye
protectors (for example, goggles or
industrial safety spectacles) and
NOTICE
When the battery is discharged, do not
close either of the front doors. The
automatic window adjusting function
will not work, and the side roof panel
may be damaged.
To start your engine with a booster battery, the
instructions and precautions below must be
followed.
For the battery maintenance information, see the
following section. (
“Battery” page 8-17)
In case of emergency 6-5
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(258,1)
remove rings, metal bands, or any
other jewelry. Do not lean over the
battery when jump starting.
.
Do not attempt to jump start a
frozen battery. It could explode
and cause serious injury.
.
Your vehicle has an automatic engine cooling fan. It could come on at
any time. Keep hands and other
objects away from it.
WARNING
Always follow the instructions below.
Failure to do so could result in damage
to the charging system and cause
personal injury.
6-6
1. If the booster battery is in another vehicle
A , position the two vehicles (*
A and *
B )
*
to bring their batteries into close proximity to
each other. Do not allow the two vehicles to touch.
2. Apply parking brake. Move the shift lever to
P position. Switch off all unnecessary
the &
In case of emergency
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(259,1)
PUSH STARTING
electrical systems (light, heater, air conditioner, etc.).
3. Remove the battery cover. Cover the battery
with a firmly wrung out moist cloth to reduce
explosion hazard.
4. Connect jumper cables in the sequence as
1 ? *
2 ? *
3 ? *
4 ).
illustrated (*
If the battery is disconnected or discharged, the steering wheel will lock
and cannot be turned. Supply power
using jumper cables before pushing
the ignition switch and disengaging
the steering lock.
CAUTION
.
.
Always connect positive (+) to positive (+) and negative (−) to body
ground (as illustrated), not to the
battery.
Make sure that the jumper cables
do not touch moving parts in the
engine compartment and that
clamps do not contact any other
metal.
5. Start the engine of the booster vehicle
and let it run for a few minutes.
6. Keep the engine speed of the booster
A at about 2,000 rpm, and start
vehicle *
the engine of the vehicle being jump started
B .
*
NOTE:
Do not keep the starter motor engaged
for more than 10 seconds. If the engine
does not start right away, push the
ignition switch to the OFF position and
wait 10 seconds before trying again.
7. After starting your engine, carefully disconnect the negative cable and then the positive
4 ? *
3 ? *
2 ? *
1 ).
cable (*
Do not attempt to start the engine by pushing.
NOTICE
Your NISSAN cannot be push-started or
tow-started. Attempting to do so may
cause transmission damage.
8. Be sure to dispose of the cloth used to
cover the vent holes as it may be contaminated with corrosive acid.
9. Put the battery cover on.
NOTE:
If the clamp clip is difficult to connect to
the battery terminal, remove the cowl top
cover to make it easier. (
“Removing
the cowl top cover” page 8-9)
A
*
In case of emergency 6-7
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(260,1)
IF YOUR VEHICLE OVERHEATS
WARNING
.
.
.
Do not continue to drive if your
vehicle overheats. Doing so could
cause engine damage or a vehicle
fire.
To avoid the danger of being
scalded, never remove the radiator
filler cap and the coolant reservoir
cap while the engine is still hot.
When the cap is removed, pressurized hot water will spurt out, possibly causing serious injury.
Do not open the hood if steam is
coming out.
If your vehicle is overheating (indicated by an
extremely high temperature gauge reading), or if
you feel a lack of engine power, detect unusual
noise, etc., take the following steps:
1. Move the vehicle safely off the road, apply
the parking brake and move the shift lever to
P position.
the &
Do not stop the engine.
3. If engine overheating is caused by climbing
a long hill on a hot day, run the engine at a
fast idle (approximately 1,500 rpm) until the
temperature gauge indication returns to
normal.
4. Get out of the vehicle. Look and listen for
steam or coolant escaping from the radiator
before opening the hood. (If steam or
coolant is escaping, turn off the engine.)
Do not open the hood further until no steam
or coolant can be seen.
5. Open the engine hood.
WARNING
If steam or water is coming from the
engine, stand clear to prevent getting
burned.
6. Visually check drive belts for damage or
looseness. Also check if the cooling fan is
running. The radiator hoses and radiator
should not leak water. If coolant is leaking,
the drive belts are missing or loose, or the
cooling fan does not run, stop the engine.
WARNING
Be careful not to allow your hands, hair,
jewelry or clothing to come into contact
with, or get caught in, engine belts or
the engine cooling fan. The engine
cooling fan can start at any time.
7. When the coolant temperature gauge goes
down to the midpoint, stop the engine and
wait until the gauge goes down further to
“C” (cold).
8. After the engine cools down, check the
coolant level in the reservoir tank. Add
coolant to the reservoir, if necessary, after
opening the coolant reservoir cap with a
heavy cloth covering it. (
“Engine cooling system” page 8-10)
9. Have your vehicle repaired at the nearest
GT-R certified NISSAN dealer.
2. Turn off the air conditioner. Open all the
windows, move the temperature control to
maximum hot and fan control to high speed.
6-8
In case of emergency
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(261,1)
TOWING YOUR VEHICLE
When towing your vehicle, all State (Provincial in
Canada) and local regulations for towing must
be followed. Incorrect towing equipment could
damage your vehicle. Towing instructions are
available from a GT-R certified NISSAN dealer.
Local service operators are familiar with the
applicable laws and procedures for towing. To
assure proper towing and to prevent accidental
damage to your vehicle, NISSAN recommends
that you have a service operator tow your
vehicle. It is advisable to have the service
operator carefully read the following precautions.
WARNING
.
.
Never ride in a vehicle that is being
towed.
Never get under your vehicle after it
has been lifted by a tow truck.
TOWING RECOMMENDED BY
NISSAN
NISSAN recommends that towing dollies be
used when towing your vehicle or the vehicle be
placed on a flat bed truck as illustrated.
NOTICE
CAUTION
Always attach safety chains before
towing.
Never tow the vehicle with any of the
wheels on the ground as this may cause
serious and expensive damage to the
powertrain.
In case of emergency 6-9
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(262,1)
VEHICLE RECOVERY (freeing a
stuck vehicle)
WARNING
.
Stand clear of a stuck vehicle.
.
Do not spin your tires at high speed.
This could cause them to explode
and result in serious injury. Parts of
your vehicle could also overheat
and be damaged.
Pulling a stuck vehicle
If your vehicle is stuck in sand, snow, mud, etc.,
use a tow strap or other device designed
specifically for vehicle recovery. Always follow
the manufacturer’s instructions for the recovery
device.
Front
Rear
Front:
1 ,
Using a suitable tool wrapped with a cloth *
2 from the front bumper.
remove the cover *
3
Securely install the vehicle recovery hook *
stored in the toolbox located under the front
4
passenger’s floor. Use the wheel nut wrench *
as illustrated to secure the recovery hook.
Attach the tow strap to the recovery hook. Make
sure that the hook is properly secured in the
6-10 In case of emergency
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(263,1)
original place after use.
Rear:
The rear hook
hook.
5
*
ery.
is designed as the recovery
NOTICE
6 from the rear bumper,
To remove the cover *
7 until they unlatch and
first push in the tabs *
then pull the cover.
.
Tow chains or cables must be attached only to the vehicle recovery
hooks or main structural members
of the vehicle. Otherwise, the vehicle body will be damaged.
.
Never tow a vehicle using the vehicle tie downs or recovery hooks.
.
Pulling devices should be routed so
they do not touch any part of the
suspension, steering, brake or cooling systems.
3
Securely install the recovery hook *
to the
attaching mount located on the rear bumper.
Make sure that the recovery hook is properly
secured in its storage location after use.
Do not use the tie down hooks for towing or
vehicle recovery.
CAUTION
.
Do not use the vehicle tie downs to
free a vehicle stuck in sand, snow,
mud, etc.
.
Always pull the cable straight out
from the vehicle. Never pull on the
vehicle at an angle.
.
Pulling devices such as ropes or
canvas straps are not recommended
for use in vehicle towing or recov-
Rocking a stuck vehicle
If your vehicle is stuck in sand, snow, mud, etc.,
use the following procedure:
1. Turn off the Vehicle Dynamic Control (VDC)
system and select SAVE mode with the
transmission setup switch. (
“VDC,
transmission and suspension setup
switches” page 5-25)
2. Make sure the area in front and behind the
vehicle is clear of obstructions.
In case of emergency 6-11
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(264,1)
3. Turn the steering wheel right and left to clear
an area around the front tires.
4. Slowly rock the vehicle forward and backward.
. Shift back and forth between the &
R and
A ↔&
M positions.
&
. Apply the accelerator as little as possible
to maintain the rocking motion.
. Release the accelerator pedal before
R and &
A ↔&
M
shifting between the &
positions.
. Do not spin the tires above 35 MPH (55
km/h).
5. Turn on the Vehicle Dynamic Control (VDC)
system.
6. If the vehicle cannot be freed after a few
tries, contact a professional towing service
to remove the vehicle.
6-12 In case of emergency
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(265,1)
7 Appearance and care
Cleaning exterior ......................................................................
Matte paint care (if so equipped) ..................................
Washing ................................................................................
Waxing ..................................................................................
Removing spots ..................................................................
Underbody ............................................................................
Glass .....................................................................................
Wheels ..................................................................................
Chrome parts ......................................................................
Outside door handles .......................................................
Tire dressing ........................................................................
7-2
7-2
7-3
7-4
7-4
7-5
7-5
7-5
7-5
7-6
7-6
Dry carbon fiber parts (if so equipped) ..................... 7-6
Cleaning interior ...................................................................... 7-7
Air fresheners .................................................................... 7-7
Floor mats .......................................................................... 7-8
Seat belts ........................................................................... 7-8
Corrosion protection ............................................................... 7-9
Most common factors contributing to
vehicle corrosion .............................................................. 7-9
Environmental factors influence the rate
of corrosion ....................................................................... 7-9
To protect your vehicle from corrosion ................... 7-10
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(266,1)
CLEANING EXTERIOR
In order to maintain the appearance of your
vehicle, it is important to take proper care of it.
To protect the paint surfaces, wash your vehicle
as soon as you can:
.
after driving on coastal roads
.
when contaminants such as soot, bird
droppings, tree sap, metal particles or bugs
get on the paint surface
. when dust or mud builds up on the surface
Whenever possible, store or park your vehicle
inside a garage or in a covered area.
When it is necessary to park outside, park in a
shady area or protect the vehicle with a body
cover.
Be careful not to scratch the paint surface
when putting on or removing the body
cover.
.
Hand wash with a wet microfiber
cloth, dry with clean damp chamois,
and use light pressure with a microfiber towel. Minimize the pressure
you use.
.
Test all cleaning products on a
hidden part of the vehicle (such as
under the rocker sills) to make
certain they do not affect the appearance of the matte paint.
.
Pre-rinse the vehicle before washing to remove coarse dirt that can
scratch the paint.
.
Do not wash using a pressure
washer.
.
Spot treat heavy dirt accumulation
with a cleaner made for matte paint.
If your vehicle is equipped with matte paint,
special care is necessary to clean your vehicle to
maintain the appearance of the matte paint.
after a rainfall to prevent possible damage
from acid rain
.
7-2
MATTE PAINT CARE (if so equipped)
CAUTION
Failure to follow the proper matte paint
care instructions can permanently affect the appearance of the paint. Improper care can result in shiny spots,
rub marks or other damage. This damage can only be repaired at a body
shop trained in matte paint repair.
Damage resulting from improper matte
paint care is not covered under NISSAN’s new vehicle limited warranty.
.
Do not use an automatic car wash.
.
Do not rub the paint.
.
.
Only use cleaners and soaps that
are specifically formulated for matte
paint.
Do not use solvent based tar and
bug remover products to clean the
vehicle.
.
Do not use waxes and sealers, even
those specifically formulated for
matte paint. These products may
affect the appearance (add shine)
of the matte paint.
.
Do not use terry cloth towels to
wash or dry the vehicle.
.
Do not rub repeatedly with any
cleaning material to minimize the
risk of burnishing a shiny spot.
Appearance and care
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(267,1)
Washing
Hand wash the vehicle for best results. Park the
vehicle in a cool, shaded area, out of direct
sunlight. Read these procedures and gather the
necessary equipment and supplies before
washing the vehicle.
Equipment/Supplies:
.
Vehicle soap specifically made for matte
paint
.
Microfiber cloth
.
Chamois cloth, for drying
.
Two buckets with grit guards or dirt separators (available at many automotive supply or
detaining supply sources).
1. Clean the wheels.
. Use a product specifically formulated to
clean wheels.
. Do not get any wheel cleaner on the
paint. Immediately wash and rinse the
paint if any wheel clear contacts the
paint.
. Do not use the same cleaning materials
to clean the wheels and paint.
2. Fill the buckets.
. Fill one bucket (with dirt separator grid at
the bottom) with vehicle soap specifically
made for matte paint and water. Follow
.
.
the soap manufacturer’s instructions.
Fill the second bucket with clean water
for rinsing the wash cloth.
Always rinse the wash cloth in the clean
water before putting the wash cloth into
the cleaning solution.
WASHING
Wash dirt off the vehicle with a wet sponge and
plenty of water. Clean the vehicle thoroughly
using a mild soap, a special vehicle soap or
general purpose dishwashing liquid mixed with
clean, lukewarm (never hot) water.
3. Inspect the car for areas with heavy soiling
or spots and, if necessary, treat these areas
first, before washing the entire vehicle.
NOTICE
4. Remove large pieces of dirt by spraying the
vehicle with a hose.
.
Do not use an automatic car wash.
The rear spoiler may be damaged.
5. Soak the wash cloth in the soap solution and
wash the vehicle lightly. Work in small
sections from the bottom of the vehicle to
the top.
. Wash a section then rinse the soapy
section of the vehicle completely before
starting another section.
. Keep the clean sections of the vehicle
wet as the remaining sections are completed.
.
Do not use car washes that use acid
in the detergent. Some car washes,
especially brushless ones, use some
acid for cleaning. The acid may react
with some plastic vehicle components, causing them to crack. This
could affect their appearance, and
also could cause them not to function properly. Always check with
your car wash to confirm that acid
is not used.
.
Do not wash the vehicle with strong
household soap, strong chemical
detergents, gasoline or solvents.
.
Do not wash the vehicle in direct
sunlight or while the vehicle body is
hot, as the surface may become
6. Use a clean damp chamois to dry the vehicle
before it air dries. If the undried surfaces
start to air dry, redampen those areas.
. Do not allow surface to air dry. Air drying
allows water spots to form.
Appearance and care 7-3
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(268,1)
.
water-spotted.
WAXING
Avoid using tight-napped or rough
cloths, such as washing mitts. Care
must be taken when removing
caked-on dirt or other foreign substances so the paint surface is not
scratched or damaged.
Regular waxing protects the paint surface and
helps retain new vehicle appearance. Polishing
is recommended to remove built-up wax residue
and to avoid a weathered appearance before
reapplying wax.
Rinse the vehicle thoroughly with plenty of clean
water.
Inside flanges, seams and folds on the doors,
hatches and hood are particularly vulnerable to
the effects of road salt. Therefore, these areas
must be regularly cleaned. Take care that the
drain holes in the lower edge of the door are
open. Spray water under the body and in the
wheel wells to loosen the dirt and wash away
road salt.
Avoid leaving water spots on the paint surface
by using a damp chamois to dry the vehicle.
A GT-R certified NISSAN dealer can assist you
in choosing the proper product.
.
Wax your vehicle only after a thorough
washing. Follow the instructions supplied
with the wax.
.
Do not use a wax containing any abrasives,
cutting compounds or cleaners that may
damage the vehicle finish.
Machine compound or aggressive polishing on a
base coat/clear coat paint finish may dull the
finish or leave swirl marks.
WARNING
Do not use wax on the glass, rubber or
plastic parts around the glass or door.
This may prevent the window operation
or cause poor visibility and the wax
cannot be coated uniformly.
7-4
NOTICE
.
Do not use compound agents on
clear-coated dry carbon fiber parts
(such as the NISMO model’s bumper, side sill protector, rear spoiler,
etc.).
.
Do not use any chemical agents
(wax, coating agent, compound
agent, etc.) on matte-painted dry
carbon fiber parts (such as the rear
diffuser, a rear spoiler that is of
specifications other than NISMO,
etc.).
REMOVING SPOTS
Remove tar and oil spots, industrial dust,
insects, and tree sap as quickly as possible
from the paint surface to avoid lasting damage
or staining. Special cleaning products are
available at a GT-R certified NISSAN dealer or
any automotive accessory stores.
Appearance and care
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(269,1)
UNDERBODY
WHEELS
In areas where road salt is used in winter, the
underbody must be cleaned regularly. This will
prevent dirt and salt from building up and
causing the acceleration of corrosion on the
underbody and suspension. Before the winter
period and again in the spring, the underseal
must be checked and, if necessary, re-treated.
Wash the wheels when washing the vehicle to
maintain their appearance.
.
NOTICE
When cleaning the inside of the windows, do not use sharp-edged tools,
abrasive cleaners or chlorine-based
disinfectant cleaners. They could damage the electrical conductors, radio
antenna elements or rear window
defroster elements.
NOTICE
Follow the directions below to avoid
staining or discoloring the wheels:
.
Inspect wheel rims regularly for dents or
corrosion. Such damage may cause loss of
pressure or poor seal at the tire bead.
.
Do not use a cleaner that uses
strong acid or alkali contents to
clean the wheels.
.
NISSAN recommends that the road wheels
be waxed to protect against road salt in
areas where it is used during winter.
.
Do not apply wheel cleaners to the
wheels when they are hot. The
wheel temperature should be the
same as ambient temperature.
.
Rinse the wheel to completely remove the cleaner within 15 minutes
after the cleaner is applied.
GLASS
Use glass cleaner to remove smoke and dust
film from the glass surfaces. It is normal for glass
to become coated with a film after the vehicle is
parked in the hot sun. Glass cleaner and a soft
cloth will easily remove this film.
Clean the inner side of the wheels when the
wheel is changed or the underside of the
vehicle is washed.
other wheels. If the wheel is changed, consult
with a GT-R certified NISSAN dealer.
CAUTION
Do not use abrasive cleaners when
washing the wheels.
Aluminum alloy wheels
Wash regularly with a sponge dampened in a
mild soap solution, especially during winter
months in areas where road salt is used. Salt
could discolor the wheels if not removed.
CHROME PARTS
Clean chrome parts regularly with a nonabrasive chrome polish to maintain the finish.
The dark chrome coat wheel is specially coated
to a distinctive color. It may discolor to black
depending on storage conditions. If only one
wheel is changed, it may be different color with
Appearance and care 7-5
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(270,1)
OUTSIDE DOOR HANDLES
.
After driving on a road where salt is used in
winter, immediately wash and clean the outside
door handles that are provided with a special
coating. This will keep the beautiful finish longer.
DRY CARBON FIBER PARTS (if so
equipped)
TIRE DRESSING
NISSAN does not recommend the use of tire
dressings. Tire manufacturers apply a coating to
the tires to help reduce discoloration of the
rubber. If a tire dressing is applied to the tires, it
may react with the coating and form a compound. This compound may come off the tire
while driving and stain the vehicle paint.
If you choose to use a tire dressing, take the
following precautions:
.
Use a water-based tire dressing. The coating on the tire dissolves more easily with an
oil-based tire dressing.
.
Apply a light coat of tire dressing to help
prevent it from entering the tire tread/
grooves (where it would be difficult to
remove).
.
Wipe off excess tire dressing using a dry
towel. Make sure the tire dressing is
completely removed from the tire tread/
grooves.
7-6
Allow the tire dressing to dry as recommended by tire dressing manufacturer.
Because of the characteristics of the material,
the dry carbon fiber parts may turn yellow due to
exposure to ultraviolet rays. The surfaces of dry
carbon fiber parts are coated with a special
ultraviolet protection paint. To maintain the
appearance of these parts, it is important to
take proper care of them.
tion by mixing one capful of mild
detergent in a bucket of water, and
use that mixture to clean the parts.
NOTE:
The surfaces of the dry carbon fiber parts
are lightly coated like a race car so that
you can feel the proper texture of real
carbon, which may feel rough. This is
normal.
NOTICE
.
Do not use compound agents on
clear-coated dry carbon fiber parts
(such as the NISMO model’s bumper, side sill protector, rear spoiler,
etc.).
.
Do not use any chemical agents
(wax, coating agent, compound
agent, etc.) on matte-painted dry
carbon fiber parts (such as the rear
diffuser, a rear spoiler that is of
specifications other than NISMO,
etc.).
.
When dry carbon fiber parts become
dirty, prepare a dilute cleaning solu-
Appearance and care
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(271,1)
CLEANING INTERIOR
Occasionally remove loose dust from the interior
trim, plastic parts and seats using a vacuum
cleaner or soft bristled brush. Wipe the vinyl and
leather surfaces with a clean, soft cloth dampened in mild soap solution, then wipe clean
with a dry soft cloth.
.
.
Never use benzine, thinner, or any
similar material.
.
For cleaning, use a soft cloth, dampened with water. Never use a rough
cloth, alcohol, benzine, thinner or
any kind of solvent or paper towel
with a chemical cleaning agent.
They will scratch or cause discoloration to the lens.
Regular care and cleaning is required in order to
maintain the appearance of the leather.
Before using any fabric protector, read the
manufacturer’s recommendations. Some fabric
protectors contain chemicals that may stain or
bleach the seat material.
Use a cloth dampened only with water, to clean
the meter and gauge lens.
.
Do not use glass or plastic cleaner
on meter or gauge lens covers. It
may damage the lens cover.
AIR FRESHENERS
Most air fresheners use a solvent that could
affect the vehicle interior. If an air freshener is
used, take the following precautions:
.
Do not spray any liquid such as
water on the meter lens. Spraying
liquid may cause the system to
malfunction.
WARNING
Do not use water or acidic cleaners (hot
steam cleaners) on the seat. This can
damage the seat or occupant classification sensor. This can also affect the
operation of the air bag system and
result in serious personal injury.
recommended by the manufacturer.
CAUTION
Hanging-type air fresheners can cause
permanent discoloration when they contact
vehicle interior surfaces. Place the air
freshener in a location that allows it to hang
free and not contact an interior surface.
.
NOTICE
.
Small dirt particles can be abrasive
and damaging to the leather surfaces and should be removed
promptly. Do not use saddle soap,
car waxes, polishes, oils, cleaning
fluids, solvents, detergents or ammonia-based cleaners as they may
damage the leather’s natural finish.
.
Never use fabric protectors unless
Liquid-type air fresheners typically clip on
the vents. These products can cause
immediate damage and discoloration when
spilled on interior surfaces.
Carefully read and follow the manufacturer’s
instructions before using air fresheners.
Appearance and care 7-7
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(272,1)
FLOOR MATS
WARNING
To avoid potential pedal interference
that may result in a collision or injury:
.
NEVER place a floor mat on top of
another floor mat in the driver front
position.
.
Use only genuine NISSAN floor
mats specifically designed for use
in your vehicle model. See your
GT-R certified NISSAN dealer for
more information.
.
Properly position the mats in the
floorwell using the floor mat positioning aid. See “Floor mat positioning aid” later in this section.
The use of genuine NISSAN floor mats can
extend the life of your vehicle carpet and make it
easier to clean the interior. Mats should be
maintained with regular cleaning and replaced if
they become excessively worn.
7-8
Bracket positions
Floor mat positioning aid
This model includes front floor mat brackets to
act as floor mat positioning aid. NISSAN floor
mats have been specially designed for your
vehicle model. The floor mats have grommet
holes in them. To install, simply position the mat
by placing the floor mat bracket through the floor
mat grommet hole while centering the mat in the
floorwell.
The illustration shows the location of the floor
mat brackets.
SEAT BELTS
The seat belts can be cleaned by wiping them
with a sponge dampened in a mild soap
solution. Allow the belts to dry completely in
the shade before using them. (
“Seat belt
maintenance” page 1-13)
Periodically check to make certain that the mats
are properly positioned.
Appearance and care
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(273,1)
CORROSION PROTECTION
MOST COMMON FACTORS CONTRIBUTING TO VEHICLE CORROSION
WARNING
Do not allow wet seat belts to roll up in
the retractor. NEVER use bleach, dye, or
chemical solvents to clean the seat
belts, since these materials may severely weaken the seat belt webbing.
.
The accumulation of moisture-retaining dirt
and debris in body panel sections, cavities,
and other areas.
.
Damage to paint and other protective coatings caused by gravel and stone chips or
minor traffic accidents.
ENVIRONMENTAL FACTORS INFLUENCE THE RATE OF CORROSION
Cleaning the power window finisher
Moisture
Moisten a soft cloth with neutral detergent and
wipe off the dirt on the power window finisher
1 .
*
Accumulation of sand, dirt and water on the
vehicle body underside can accelerate corrosion. Wet floor coverings will not dry completely
inside the vehicle, and should be removed for
drying to avoid floor panel corrosion.
After wiping off the dirt, soak a cloth with water
and wring it out thoroughly, then wipe off the
neutral detergent.
NOTICE
Some cleaners may cause the paint to
peel or cause spots to occur. If using a
cleaner, consult with a GT-R certified
NISSAN dealer.
Relative humidity
Corrosion will be accelerated in areas of high
relative humidity, especially those areas where
the temperatures stay above freezing where
atmospheric pollution exists, or where road salt
is used.
Appearance and care 7-9
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(274,1)
Temperature
A temperature increase will accelerate the rate
of corrosion to those parts which are not well
ventilated.
CAUTION
.
NEVER remove dirt, sand or other
debris from the passenger compartment by washing it out with a hose.
Remove dirt with a vacuum cleaner.
.
Never allow water or other liquids to
come in contact with electronic
components inside the vehicle as
this may damage them.
Air pollution
Industrial pollution, the presence of salt in the air
in coastal areas, or heavy road salt use will
accelerate the corrosion process. Road salt will
also accelerate the disintegration of paint
surfaces.
TO PROTECT YOUR VEHICLE FROM
CORROSION
.
Wash and wax your vehicle often to keep the
vehicle clean.
.
Always check for minor damage to the paint
and repair it as soon as possible.
.
Keep drain holes at the bottom of the doors
open to avoid water accumulation.
.
Check the underbody for accumulation of
sand, dirt or salt. If present, wash with water
as soon as possible.
Chemicals used for road surface deicing are
extremely corrosive. They accelerate corrosion
and deterioration of underbody components
such as the exhaust system, fuel and brake
lines, brake cables, floor pan and fenders.
In winter, the underbody must be cleaned
periodically.
For additional protection against rust and
corrosion, which may be required in some areas,
consult a GT-R certified NISSAN dealer.
7-10 Appearance and care
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(275,1)
8 Maintenance and do-it-yourself
Maintenance requirements ..................................................... 8-3
Scheduled maintenance ................................................... 8-3
General maintenance ........................................................ 8-3
Where to go for service ................................................... 8-3
General maintenance .............................................................. 8-4
Explanation of maintenance items ................................. 8-4
Maintenance precautions ....................................................... 8-6
Engine compartment check locations ................................. 8-8
Removing the cowl top cover ......................................... 8-9
Engine cooling system ......................................................... 8-10
Checking engine coolant level ..................................... 8-11
Changing engine coolant .............................................. 8-12
Engine oil ................................................................................ 8-13
Checking engine oil level .............................................. 8-13
Changing engine oil and filter ...................................... 8-14
Transmission oil ..................................................................... 8-14
Power steering fluid .............................................................. 8-14
Brake fluid ............................................................................... 8-15
Window washer fluid ........................................................... 8-16
Battery ...................................................................................... 8-17
Precautions ....................................................................... 8-17
Fluid level check .............................................................. 8-18
Jump starting .................................................................... 8-19
Drive belts ..............................................................................
Spark plugs ............................................................................
Replacing spark plugs .................................................
Air cleaner ..............................................................................
Windshield wiper blades ....................................................
Cleaning ..........................................................................
Replacing the wiper blades .......................................
Brakes .....................................................................................
Self-adjusting brakes ...................................................
Brake pad wear warning .............................................
High performance brake system ...............................
Replacing the brake pads ...........................................
Fuses .......................................................................................
Engine compartment ....................................................
Passenger compartment .............................................
Intelligent Key battery replacement ..................................
Lights .......................................................................................
Headlights .......................................................................
Exterior and interior lights ...........................................
Wheels and tires ..................................................................
Tire pressure ..................................................................
Tire and loading information label ............................
Checking the tire pressure .........................................
[ Edit: 2014/ 12/ 8
8-19
8-20
8-20
8-21
8-22
8-22
8-23
8-23
8-23
8-23
8-24
8-24
8-25
8-25
8-26
8-27
8-29
8-30
8-30
8-32
8-32
8-35
8-36
Model: R35-D ]
(276,1)
Tire labeling ...................................................................... 8-37
Types of tires .................................................................... 8-38
Tire chains ......................................................................... 8-40
Changing wheels and tires ......................................... 8-41
Jacking vehicle and removing wheels ...................... 8-43
Wheel lock nuts (if so equipped) ............................. 8-49
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(277,1)
MAINTENANCE REQUIREMENTS
Some day-to-day and regular maintenance is
essential to maintain your vehicle good mechanical condition, as well as its emission and engine
performance.
It is the owner’s responsibility to make sure that
the scheduled maintenance, as well as general
maintenance, is performed.
As the vehicle owner, you are the only one who
can ensure that your vehicle receives the proper
maintenance care. You are a vital link in the
maintenance chain.
SCHEDULED MAINTENANCE
For your convenience, both required and optional scheduled maintenance items are described and listed in your NISSAN Service and
Maintenance Guide. You must refer to that guide
to ensure that necessary maintenance is performed on your vehicle at regular intervals.
GENERAL MAINTENANCE
General maintenance includes those items
which should be checked during normal dayto-day operation. They are essential for proper
vehicle operation. It is your responsibility to
perform these procedures regularly as prescribed.
Performing general maintenance checks requires minimal mechanical skill and only a few
general automotive tools.
These checks or inspections can be done by
yourself, a qualified technician or, if you prefer, a
GT-R certified NISSAN dealer.
387-0122 in Canada, or go to www. gtrnissan.
com/.
WHERE TO GO FOR SERVICE
GT-R certified NISSAN dealers are required to
have additional training and equipment and are
the only NISSAN dealers authorized to perform
warranty work on key vehicle performance
systems such as engine, transmission, suspension and brakes.
If maintenance service is required or your vehicle
appears to malfunction, have the systems
checked and serviced by a GT-R certified
NISSAN dealer.
NISSAN technicians are well-trained specialists
and are kept up to date with the latest service
information through technical bulletins, service
tips, and in-dealer information systems. They are
completely qualified to work on NISSAN vehicles before work begins.
You can be confident that a GT-R certified
NISSAN dealer’s service department performs
the best job to meet the maintenance requirements on your vehicle.
To find a GT-R certified NISSAN dealer near
you, call 1-866-668-1GTR in the US or 1-800Maintenance and do-it-yourself 8-3
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(278,1)
GENERAL MAINTENANCE
During the normal day-to-day operation of the
vehicle, general maintenance should be performed regularly as prescribed in this section. If
you detect any unusual sounds, vibrations or
smell, be sure to check for the cause or have a
GT-R certified NISSAN dealer do it promptly. In
addition, you should notify a GT-R certified
NISSAN dealer if you think that repairs are
required. (
“Maintenance precautions”
page 8-6)
EXPLANATION OF MAINTENANCE
ITEMS
Additional information on the following
items with “*” is found later in this section.
Outside the vehicle
The maintenance items listed here should be
performed from time to time, unless otherwise
specified.
Doors and engine hood: Check that all doors
and the engine hood, operate properly. Also
ensure that all latches lock securely. Lubricate
hinges, latches, latch pins, rollers and links if
necessary. Make sure that the secondary latch
keeps the hood from opening when the primary
latch is released.
When driving in areas using road salt or other
corrosive materials, check lubrication frequently.
8-4
Lights*: Clean the headlights on a regular basis.
Make sure that the headlights, stop lights, tail
lights, turn signal lights, and other lights are all
operating properly and installed securely. Also
check headlight aim.
.
Road wheel nuts (lug nuts)*: When checking
the tires, make sure no wheel nuts are missing,
and check for any loose wheel nuts. Tighten if
necessary.
Tire Pressure Monitoring System (TPMS)
transmitter components: Replace grommet
seal of transmitter in TPMS, when replacing
each tire by reaching the wear limit.
Tire rotation*: Tires cannot be rotated because
your vehicle is equipped with different sized tires
in the front and rear.
Tire, wheel alignment and balance: If the
vehicle should pull to either side while driving on
a straight and level road, or if you detect uneven
or abnormal tire wear, there may be a need for
wheel alignment.
Tires*: Check the pressure with a gauge often
and always prior to long distance trips. If
necessary, adjust the pressure in all tires to the
pressure specified. Check carefully for damage,
cuts or excessive wear.
NOTE:
. You can check the pressure of all four
tires on the multi function display. See
the separate Multi Function Display
Owner’s Manual.
.
The tires of this vehicle are filled with
nitrogen gas. When the tire pressure is
low, fill the tires with nitrogen. Contact
a GT-R certified NISSAN dealer for
information on filling the tires with
nitrogen.
If nitrogen is not available, compressed
air may be safely used under normal
driving conditions. However, NISSAN
recommends refilling with nitrogen for
maximum tire performance.
If the steering wheel or seat vibrates at normal
highway speeds, wheel balancing may be
needed.
For additional information regarding tires, refer
to “Important Tire Safety Information” (US) or
“Tire Safety Information” (Canada) in the Warranty Information Booklet.
Windshield: Clean the windshield on a regular
basis. Check the windshield at least every six
months for cracks or other damage. Have a
damaged windshield repaired by a qualified
repair facility.
Windshield wiper blades*: Check for cracks
or wear if they do not wipe properly.
Maintenance and do-it-yourself
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(279,1)
Inside the vehicle
The maintenance items listed here should be
checked on a regular basis, such as when
performing scheduled maintenance, cleaning
the vehicle, etc.
Accelerator pedal: Check the pedal for
smooth operation and make sure the pedal
does not catch or require uneven effort. Keep
the floor mat away from the pedal.
P mechanism: On a fairly
Transmission &
steep hill, check that your vehicle is held
P position
securely with the shift lever in the &
without applying any brakes.
Brake pedal: Check the pedal for smooth
operation. If the brake pedal suddenly goes
down further than normal, the pedal feels
spongy or the vehicle seems to take longer to
stop, see a GT-R certified NISSAN dealer
immediately. Keep the floor mat away from the
pedal.
Brakes: Check that the brakes do not pull the
vehicle to one side when applied.
Parking brake: Check the parking brake
operation regularly. The vehicle should be
securely held on a fairly steep hill with only the
parking brake applied. If the parking brake needs
to be adjusted, see a GT-R certified NISSAN
dealer.
Seat belts: Check that all parts of the seat belt
system (for example, buckles, anchors, adjuster
and retractors) operate properly and smoothly,
and are installed securely. Check the belt
webbing for cuts, fraying, wear or damage.
Under the hood and vehicle
The maintenance items listed here should be
checked periodically (for example, each time you
check the engine oil or refuel).
Seats: Check seat position controls such as
seat adjusters, seatback recliner, etc. to ensure
they operate smoothly and that all latches lock
securely in every position.
Battery*: Check the fluid level in each cell. It
should be between the MAX and MIN lines.
Vehicles operated in high temperatures or under
severe condition require frequent checks of the
battery fluid level.
Steering wheel: Check for changes in the
steering conditions, such as excessive free play,
hard steering or strange noises.
NOTE:
Warning lights and chimes: Make sure that
all warning lights and chimes are operating
properly.
Windshield defroster: Check that the air
comes out of the defroster outlets properly and
in sufficient quantity when operating the heater
or air conditioner.
Windshield wiper and washer*: Check that
the wipers and washer operate properly and that
the wipers do not streak.
Care should be taken to avoid situations
that can lead to potential battery discharge
and potential no-start conditions such as:
1. Installation or extended use of electronic accessories that consume battery
power when the engine is not running
(Phone chargers, GPS, DVD players,
etc.)
2. Vehicle is not driven regularly and/or
only driven short distances.
In these cases, the battery may need to be
charged to maintain battery health.
Brake fluid level*: Make sure that the brake
fluid level is between the MAX and MIN lines on
the reservoir.
Engine coolant level*: Check the coolant level
when the engine is cold.
Maintenance and do-it-yourself 8-5
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(280,1)
MAINTENANCE PRECAUTIONS
Engine drive belts*: Make sure that no belt is
frayed, worn, cracked or oily.
Engine oil level*: Check the level after parking
the vehicle on a level spot and turning off the
engine. Wait at least 5 minutes for the oil to
drain back into the oil pan before checking the
oil.
Exhaust system: Make sure there are no loose
supports, cracks or holes. If the sound of the
exhaust seems unusual or there is a smell of
exhaust fumes in the engine compartment,
immediately have the exhaust system inspected
b y a GT- R c e r t i f i e d N I S S A N d e a l e r .
(
“Exhaust gas (carbon monoxide)” page
5-3)
Fluid leaks: Check under the vehicle for fuel,
oil, water or other fluid leaks after the vehicle has
been parked for a while. Water dripping from the
air conditioner after use is normal. If you should
notice any leaks or if gasoline fumes are evident,
check for the cause and have it corrected
immediately.
Power steering fluid level* and lines: Check
the level when the fluid is cold, with the engine
off. Check the lines for proper attachment, leaks,
cracks, etc.
8-6
Radiator and hoses: Check the front of the
radiator and clean off any dirt, insects, leaves,
etc., that may have accumulated. Make sure the
hoses have no cracks, deformation, rot or loose
connections.
Underbody: The underbody is frequently exposed to corrosive substances such as those
used on icy roads or to control dust. It is very
important to remove these substances, otherwise rust will form on the floor pan, frame, fuel
lines and around the exhaust system. At the end
of winter, the underbody should be thoroughly
flushed with plain water, being careful to clean
those areas where mud and dirt may accumulate. (
“Underbody” page 7-5)
When performing any inspection or maintenance work on your vehicle, always take care
to prevent serious accidental injury to yourself or
damage to the vehicle. The following are general
precautions which should be closely observed.
WARNING
.
Park the vehicle on a level surface,
apply the parking brake securely
and block the wheels to prevent
the vehicle from moving. Move the
P position.
shift lever to the &
.
Be sure the ignition switch is in the
OFF or LOCK position when performing any parts replacement or
repairs.
.
If you must work with the engine
running, keep your hands, clothing,
hair and tools away from moving
fans, belts and any other moving
parts.
.
It is advisable to secure or remove
any loose clothing and remove any
jewelry, such as rings, watches, etc.
before working on your vehicle.
.
Always wear eye protection whenever you work on your vehicle.
Windshield washer fluid*: Check that there is
adequate fluid in the reservoir.
Maintenance and do-it-yourself
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(281,1)
.
.
If you must run the engine in an
enclosed space such as a garage, be
sure there is proper ventilation for
exhaust gases to escape.
Never get under the vehicle while it
is supported only by a jack. If it is
necessary to work under the vehicle,
support it with safety stands.
.
Keep smoking materials, flame and
sparks away from fuel tank and the
battery.
.
Your vehicle is equipped with an
automatic engine cooling fan. It may
come on at any time without warning, even if the ignition key is in the
OFF position and the engine is not
running. To avoid injury, always
disconnect the negative battery
cable before working near the fan.
.
The fuel filter or fuel lines should be
serviced by a GT-R certified NISSAN
dealer because the fuel lines are
under high pressure even when the
engine is off.
CAUTION
.
Do not work under the hood while
the engine is hot. Turn the engine
off and wait until it cools down.
.
Avoid direct contact with used engine oil and coolant. Improperly
disposed engine oil, coolant, and/
or other vehicle fluids can damage
the environment. Always conform to
local regulations for disposal of
vehicle fluid.
A genuine NISSAN Service Manual is also
available. (
“Owner’s Manual/Service Manual order information” page 9-22)
You should be aware that incomplete or
improper servicing may result in operating
difficulties or excessive emissions. If in doubt
about any servicing, we recommend that it
be done by a GT-R certified NISSAN dealer.
NOTICE
.
Never connect or disconnect the
battery or any transistorized component while the ignition switch is
in the ON position.
.
Never leave the engine or transmission related component harnesses
disconnected while the ignition
switch is in the ON position.
This “8. Maintenance and do-it-yourself” section
gives instructions regarding only those items
which are relatively easy for an owner to perform.
Maintenance and do-it-yourself 8-7
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(282,1)
ENGINE COMPARTMENT CHECK
LOCATIONS
NOTICE
The coolant reservoir is equipped with a
pressure type cap, and the radiator is
equipped with a non-pressure type cap.
Do not switch the radiator filler cap and
the coolant reservoir cap. Doing so will
cause substandard cooling performance and overheating.
1.
2.
3.
4.
5.
6.
8-8
Fuse/fusible link holder
Battery
Engine oil filler cap
Engine oil dipstick
Brake fluid reservoir
Air cleaner
7.
8.
9.
10.
11.
Power steering fluid reservoir
Radiator filler cap
Coolant reservoir cap (pressure type)
Coolant reservoir
Window washer fluid reservoir
Maintenance and do-it-yourself
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(283,1)
REMOVING THE COWL TOP COVER
Remove the cowl top cover if necessary.
2. Unfasten the 5 clips and remove the cowl
A by pulling it up.
top cover *
3. Unfasten the 3 clips and remove the cowl
B by pulling it towards the front
top cover *
of the vehicle.
1. Remove the battery cover.
Maintenance and do-it-yourself 8-9
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(284,1)
ENGINE COOLING SYSTEM
The engine cooling system is filled at the factory
with a pre-diluted mixture of 50% Genuine
NISSAN Long Life Antifreeze/Coolant (blue) and
50% water to provide year-round anti-freeze
and coolant protection. The anti-freeze solution
contains rust and corrosion inhibitors. Additional
engine cooling system additives are not necessary.
WARNING
.
Never remove the radiator or coolant reservoir cap when the engine is
hot. Wait until the engine and
radiator cool down. Serious burns
could be caused by high pressure
fluid escaping from the radiator.
(
“If your vehicle overheats”
page 6-8)
.
The radiator is equipped with a
pressure type radiator cap. To prevent engine damage, use only a
genuine NISSAN radiator cap.
ine NISSAN Long Life Antifreeze/
Coolant (blue) or equivalent may
damage the engine cooling system.
CAUTION
.
.
Never use any cooling system additives such as radiator sealer. Additives may clog the cooling system
and cause damage to the engine,
transmission and/or cooling system.
When adding or replacing coolant,
be sure to use only Genuine
NISSAN Long Life Antifreeze/Coolant (blue) or equivalent. Genuine
NISSAN Long Life Antifreeze/Coolant (blue) is pre-diluted to provide
antifreeze protection to −348F
(−378C). If additional freeze protection is needed due to weather where
you operate your vehicle, add Genuine NISSAN Long Life Antifreeze/
Coolant (blue) concentrate following the directions on the container.
If an equivalent coolant other than
Genuine NISSAN Long Life Antifreeze/ Coolant (blue) is used, follow the coolant manufacture’s
instructions to maintain minimum
antifreeze protection to −348F
(−378C). The use of other types of
coolant solutions other than Genu-
.
The life expectancy of the factory-fill
coolant is 24,000 miles (38,400 km)
or 2 years. Mixing any other type of
coolant other than Genuine NISSAN
Long Life Antifreeze/Coolant (blue),
including Genuine NISSAN Long
Life Antifreeze/Coolant (green), or
the use of nondistilled water will
reduce the life expectancy of the
factory-fill coolant. Refer to the
GT-R Service and Maintenance
Guide for more details.
8-10 Maintenance and do-it-yourself
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(285,1)
CHECKING ENGINE COOLANT LEVEL
1 :
*
2 :
*
3 :
*
Except for NISMO models
NISMO models
MAX line
MIN line
Between MAX and MIN lines (except for NISMO
models)
Check the coolant level in the reservoir when
the engine is cold. If the coolant level is below
2 , open the reservoir cap
the MIN level *
B
(pressure type) *
and add coolant up to
1 and MIN *
2 level. If the
between the MAX *
A
reservoir is empty, open the radiator filler cap *
and check the coolant level in the radiator when
the engine is cold. If there is insufficient
coolant in the radiator, fill the radiator with
coolant up to the filler opening and also add it to
1 and
the reservoir up to between the MAX *
2 level.
MIN *
This vehicle contains Genuine NISSAN Long
Life Antifreeze/Coolant (blue). The life expectancy of the factory-fill coolant is 24,000 miles
Maintenance and do-it-yourself 8-11
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(286,1)
(38,400 km) or 2 years. Mixing any other type of
coolant or the use of non-distilled water will
reduce the life expectancy of the factory-fill
coolant. Refer to the GT-R Service and Maintenance Guide for more details.
NOTICE
.
If the cooling system frequently requires
coolant, have it checked by a GT-R certified
NISSAN dealer.
Check that the level of coolant is between MAX
and MIN on the pressurized radiator reservoir. If
the level is below the midpoint, the amount of
coolant circulating may be insufficient for maximum vehicle performance, possibly causing
engine overheating or other trouble.
For the coolant level and mixture ratio when
engaging in performance driving, see
“Coolant level and mixture ratio” page
GTR-15.
Except for NISMO models:
If it is difficult to determine the midpoint between
MAX and MIN, remove the coolant reservoir cap
and look inside through the opening to check
3
that the coolant level is above the divider *
between the top half and bottom half of the
pressurized coolant reservoir.
.
The coolant reservoir is equipped
with a pressure type cap, and the
radiator is equipped with a nonpressure type cap. Do not switch
the radiator filler cap and the coolant reservoir cap. Doing so will
cause substandard cooling performance and overheating.
If you have added only water as the
coolant in an emergency, change it
to a coolant mixture ratio specified
as soon as possible.
CHANGING ENGINE COOLANT
If major cooling system repairs are required,
contact a GT-R certified NISSAN dealer. The
service procedures can be found in the appropriate NISSAN Service Manual.
WARNING
.
To avoid the danger of being
scalded, never change the coolant
when the engine is hot.
.
Never remove the radiator filler cap
and the coolant reservoir cap when
the engine is hot. Serious burns
could be caused by high pressure
fluid escaping from the radiator and
reservoir.
.
Avoid direct skin contact with used
coolant. If skin contact is made,
wash thoroughly with soap or hand
cleaner as soon as possible.
.
Keep coolant out of reach of children and pets.
Engine coolant must be disposed of properly.
Check your local regulations.
Improper servicing can result in reduced
heater performance and engine overheating.
8-12 Maintenance and do-it-yourself
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(287,1)
ENGINE OIL
and pour recommended oil through the
3 .
opening. Do not overfill *
6. Recheck oil level with the dipstick.
CHECKING ENGINE OIL LEVEL
1. Park the vehicle on a level surface and apply
the parking brake.
2. Run the engine until it reaches operating
temperature.
3. Turn off the engine. Wait at least 5
minutes for the oil to drain back into
the oil pan before checking the oil.
NOTE:
. It is normal to add some oil between oil
maintenance intervals or during the
break-in period, depending on the
severity of operating conditions. More
engine oil is consumed by frequent
acceleration/deceleration especially
when the engine rpm is high. If your
rate of oil consumption increases suddenly or without explanation, NISSAN
recommends that you have your vehicle
inspected by a GT-R certified NISSAN
dealer.
.
When the vehicle is delivered, the
engine oil is set to 0.39 in (10 mm)
below the H mark for optimal high
performance driving. The engine oil can
be filled up to the H mark if performance driving is not engaged.
NOTICE
.
Mobil 1 (0W-40) (100% synthetic) is
the factory fill oil. The VR38 engine
with its plasma-sprayed bores was
developed using this oil. NISSAN
cannot ensure proper engine operation and durability if other 0W-40
synthetic oil is used. If Mobil 1 (0W40) is not available, Mobil 1 (10W40) (100% synthetic) may be used;
however, some performance loss
may be noticed.
.
Oil level should be checked regularly. Operating the engine with an
insufficient amount of oil can damage the engine. See the 2016
NISSAN GT-R Warranty Information
Booklet for details including applicable exclusions.
4. Remove the dipstick and wipe it clean.
Reinsert it all the way.
5. Remove the dipstick again and check the oil
1 . If the
level. It should be within the range *
2 , remove the oil filler cap
oil level is below *
Maintenance and do-it-yourself 8-13
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(288,1)
TRANSMISSION OIL
CHANGING ENGINE OIL AND FILTER
NOTE:
NOTE:
When checking or replacement is required,
contact a GT-R certified NISSAN dealer for
servicing.
When replacement is required, contact a
GT-R certified NISSAN dealer for servicing.
POWER STEERING FLUID
NOTICE
WARNING
.
Prolonged and repeated contact
with used engine oil may cause skin
cancer.
.
Use only Genuine NISSAN Transmission Oil R35 Special. Do not mix
with other fluids.
.
Try to avoid direct skin contact with
used oil. If skin contact is made,
wash thoroughly with soap or hand
cleaner as soon as possible.
.
.
Keep used engine oil out of reach of
children.
Using transmission oil other than
Genuine NISSAN Transmission Oil
R35 Special will cause deterioration
in driveability and transmission durability, and may damage the transmission. See the 2016 NISSAN GT-R
Warranty Information Booklet for
details including applicable exclusions.
Check the fluid level in the reservoir. Remove the
cap that is attached with a gauge inside.
The fluid level should be checked using the front
1 : HOT
side of the gauge marked “HOT” (*
2 : HOT MAX.) at fluid temperatures of
MIN., *
122 to 1768F (50 to 808C) or using the reverse
3 : COLD
side of the gauge marked “COLD” (*
4 : COLD MAX.) at fluid temperatures of
MIN., *
32 to 868F (0 to 308C).
If the fluid is below the MIN line, add Genuine
NISSAN PSF or equivalent. Remove the cap
and fill through the opening.
8-14 Maintenance and do-it-yourself
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(289,1)
BRAKE FLUID
NOTE:
For maximum steering system performance, adjust the fluid level at the line
5
6
at the hot fluid temperature or *
at
*
the cold fluid temperature. Contact a GT-R
certified NISSAN dealer when precise fluid
level adjustment is required.
For further brake fluid information, see the
following section. (
“Capacities and recommended fluids/lubricants” page 9-2)
WARNING
.
Use only new fluid from a sealed
container. Old, inferior or contaminated fluid may damage the brake
system. The use of improper fluids
can damage the brake system and
affect the vehicle’s stopping ability.
.
Clean the filler cap before removing.
.
Brake fluid is poisonous and should
be stored carefully in marked containers out of the reach of children.
NOTICE
.
Do not overfill.
.
Use Genuine NISSAN PSF or
equivalent.
NOTICE
Do not spill the fluid on any painted
surfaces. This will damage the paint. If
fluid is spilled, wash the surface with
water.
CAUTION
Genuine NISSAN Brake Fluid R35 Special II is the factory fill brake fluid. The
Vehicle Dynamic Control (VDC) unit and
other related parts were specially designed for this brake fluid and NISSAN
cannot ensure proper operation of the
vehicle if other brake fluid is used.
Maintenance and do-it-yourself 8-15
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(290,1)
WINDOW WASHER FLUID
washer fluid into the tank opening.
Add a washer solvent to the washer for better
cleaning. In the winter season, add a windshield
washer antifreeze. Follow the manufacturer’s
instructions for the mixture ratio.
Refill the reservoir more frequently when driving
conditions require an increased amount of
window washer fluid.
NOTICE
Check the fluid level in the reservoir. If the fluid is
1 or the brake warning
below the MIN line *
light comes on, add Genuine NISSAN Brake
2 .
Fluid R35 Special II fluid up to the MAX line *
If fluid must be added frequently, the system
should be checked by a GT-R certified NISSAN
dealer.
WARNING
Antifreeze is poisonous and should be
stored carefully in marked containers
out of the reach of children.
Fill the window washer fluid reservoir periodically. Add window washer fluid when the low
washer fluid warning appears on the vehicle
information display. (
“Low washer fluid
warning” page 2-42)
To fill the window washer fluid reservoir, lift the
cap off the reservoir tank and pour the window
.
Do not substitute engine anti-freeze
coolant for window washer solution.
This may result in damage to the
paint.
.
Do not fill the window washer
reservoir tank with washer fluid
concentrates at full strength. Some
methyl alcohol based washer fluid
concentrates may permanently stain
the grille if spilled while filling the
window washer reservoir tank.
NOTE:
Pre-mix washer fluid concentrates with
water to the manufacturer’s recommended
levels before pouring the fluid into the
window washer reservoir. Do not use the
8-16 Maintenance and do-it-yourself
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(291,1)
BATTERY
window washer reservoir to mix the
washer fluid concentrate and water.
.
Keep the battery surface clean and dry.
Clean the battery with a solution of baking
soda and water.
.
Make certain the terminal connections are
clean and securely tightened.
.
If the vehicle is not to be used for 30 days or
longer, disconnect the negative (−) battery
terminal cable to prevent discharging it.
NOTE:
Care should be taken to avoid situations
that can lead to potential battery discharge
and potential no-start conditions such as:
1. Installation or extended use of electronic accessories that consume battery
power when the engine is not running
(Phone chargers, GPS, DVD players,
etc.)
2. Vehicle is not driven regularly and/or
only driven short distances.
In these cases, the battery may need to be
charged to maintain battery health.
PRECAUTIONS
NOTICE
When the battery cable is removed from
the battery terminal, do not close either
of the front doors. The automatic window adjusting function will not work,
and the side roof panel may be damaged.
To disconnect the negative (−) battery terminal,
perform the procedure in the following order.
Otherwise, the window and the side roof panel
may contact and be damaged.
1. Close the windows.
2. Open the hood.
3. Close and lock all the doors.
4. Disconnect the negative (−) battery terminal.
5. Securely close the hood.
To connect the negative (−) battery terminal,
perform the procedure in the following order.
Otherwise, the window and the side roof panel
may contact and be damaged.
1. Unlock and open the driver side door. Do
not close the door.
2. Open the hood.
Maintenance and do-it-yourself 8-17
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(292,1)
3. Connect the negative (−) battery terminal.
Then close the hood.
4. Fully open the driver side door window.
and remove all jewelry.
.
Battery posts, terminals and related
accessories contain lead and lead
compounds. Wash hands after
handling.
.
Keep the battery out of the reach of
children.
5. Close the driver side door and the window.
FLUID LEVEL CHECK
WARNING
.
Do not expose the battery to flames
or electrical sparks. Hydrogen gas
generated by the battery is explosive. Do not allow battery fluid to
contact your skin, eyes, fabrics, or
painted surfaces. After touching a
battery or battery cap, do not touch
or rub your eyes. Thoroughly wash
your hands. If the acid contacts your
eyes, skin or clothing, immediately
flush with water for at least 15
minutes and seek medical attention.
.
Do not operate the vehicle if the
fluid in the battery is low. Low
battery fluid can cause a higher load
on the battery which can generate
heat, reduce battery life, and in
some cases lead to an explosion.
.
When working on or near a battery,
always wear suitable eye protection
Check the fluid level in each cell (Remove the
battery cover if it is necessary). It should be
1 and LOWER
between the UPPER LEVEL *
2 lines.
LEVEL *
If it is necessary to add fluid, add only distilled
water to bring the level to the indicator in each
filler opening. Do not overfill.
8-18 Maintenance and do-it-yourself
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(293,1)
DRIVE BELTS
JUMP STARTING
If jump starting is necessary, see the following
section. (
“Jump starting” page 6-5)
If the engine does not start by jump starting, the
battery may have to be replaced. Contact a
GT-R certified NISSAN dealer.
1. Remove the cell plugs
A .
*
2. Add distilled water up to the UPPER LEVEL
1 line.
*
If the side of the battery is not clear, check
the distilled water level by looking directly
1 indicates
above the cell; the condition *
2 needs more to
OK and the conditions *
be added.
3. Tighten cell plugs
A .
*
Vehicles operated in high temperatures or under
severe conditions require frequent checks of the
battery fluid level.
1.
2.
3.
4.
5.
Power steering fluid pump
Alternator
Crankshaft pulley
Air conditioner compressor
Drive belt auto-tensioner
WARNING
Be sure the ignition switch is in the OFF
or LOCK position before servicing drive
belts. The engine could rotate unexpectedly.
1. Visually inspect each belt for signs of
unusual wear, cuts, fraying or looseness. If
Maintenance and do-it-yourself 8-19
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(294,1)
SPARK PLUGS
the belt is in poor condition or loose, have it
replaced or adjusted by a GT-R certified
NISSAN dealer.
2. Have the belts checked regularly for condition and tension in accordance with the
maintenance schedule in your NISSAN
Service and Maintenance Guide.
WARNING
Be sure the engine and the ignition
switch are off and that the parking
brake is engaged securely.
NOTICE
Be sure to use the correct socket to
remove the spark plugs. An incorrect
socket can damage the spark plugs.
REPLACING SPARK PLUGS
If replacement is required, see a GT-R certified
NISSAN dealer for servicing.
Iridium-tipped spark plugs
It is not necessary to replace the iridium-tipped
spark plugs as frequently as the conventional
type spark plugs since they will last much longer.
Follow the maintenance schedule in NISSAN
Service and Maintenance Guide, but do not
reuse them by cleaning or regapping.
Always replace spark plugs with recommended or equivalent ones.
8-20 Maintenance and do-it-yourself
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(295,1)
AIR CLEANER
replacing the filter, wipe the inside of the air
cleaner housing and the cover with a damp
cloth.
WARNING
.
Operating the engine with the air
cleaner removed can cause you or
others to be burned. The air cleaner
not only cleans the air, it stops
flame if the engine backfires. If it
isn’t there, and the engine backfires,
you could be burned. Do not drive
with the air cleaner removed, and be
careful when working on the engine
with the air cleaner removed.
.
Never pour fuel into the throttle
body or attempt to start the engine
with the air cleaner removed. Doing
so could result in serious injury.
1 as illustrated and pull
Remove the retainers *
2 .
out the filter element *
The filter element should not be cleaned and
reused. Replace it according to the maintenance
intervals. See NISSAN Service and Maintenance Guide for maintenance intervals. When
Maintenance and do-it-yourself 8-21
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(296,1)
WINDSHIELD WIPER BLADES
CLEANING
If your windshield is not clear after using the
windshield washer or if a wiper blade chatters
when running, wax or other material may be on
the blade or windshield.
Clean the outside of the windshield with a
washer solution or a mild detergent. Your
windshield is clean if beads do not form when
rinsing with clear water.
Clean each blade by wiping it with a cloth
soaked in a washer solution or a mild detergent.
Then rinse the blade with clear water. If your
windshield is still not clear after cleaning the
blades and using the wiper, replace the blades.
CAUTION
Worn windshield wiper blades can
damage the windshield and impair
driver vision.
8-22 Maintenance and do-it-yourself
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(297,1)
BRAKES
REPLACING THE WIPER BLADES
If the brakes do not operate properly, have the
brakes checked by a GT-R certified NISSAN
dealer.
Replace the wiper blades if they are worn.
1. Pull the wiper arm.
SELF-ADJUSTING BRAKES
A , and then move the
2. Push the release tab *
1 while
wiper blade down the wiper arm *
pushing the release tab to remove.
Your vehicle is equipped with self-adjusting
brakes.
The disc-type brakes self-adjust every time the
brake pedal is applied.
3. Insert the new wiper blade onto the wiper
arm until a click sounds.
4. Rotate the wiper blade so the dimple is in
the groove.
WARNING
See a GT-R certified NISSAN dealer for
a brake system check if the brake pedal
height does not return to normal.
NOTICE
.
.
After wiper blade replacement, return the wiper arm to its original
position; otherwise it may be damaged when the hood is opened.
BRAKE PAD WEAR WARNING
Make sure the wiper blades contact
the glass; otherwise the arm may be
damaged from wind pressure.
A .
Be careful not to clog the washer nozzle *
This may cause improper windshield washer
operation. If the nozzle is clogged, remove any
B . Be
objects with a needle or small pin *
careful not to damage the nozzle.
The disc brake pads have audible wear warnings. When a brake pad requires replacement, it
will make a high pitched scraping sound when
the vehicle is in motion. This scraping sound will
first occur only when the brake pedal is
depressed. After more wear of the brake pad,
the sound will always be heard even if the brake
pedal is not depressed. Have the brakes
checked as soon as possible if the wear warning
sound is heard.
Under some driving or climate conditions,
Maintenance and do-it-yourself 8-23
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(298,1)
occasional brake squeak, squeal or other noise
may be heard. Occasional brake noise during
light to moderate stops is normal and does not
affect the function or performance of the brake
system.
Proper brake inspection intervals should
be followed. For additional information, see the
maintenance log section of your NISSAN
Service and Maintenance Guide for maintenance intervals.
HIGH PERFORMANCE BRAKE SYSTEM
This vehicle is equipped with high performance
brake pads that provide appropriate braking
force in a broad range of driving environments.
Due to the material used for the brake pads, the
road wheels may become more easily covered
by brake dust, however this does not indicate
that there is a malfunction.
The GT-R brake pads use material that contains
a lot of iron to maintain steady braking performance even in high and low temperatures.
However, if the brake system is wet and the
parking brake is applied for a long time, the iron
in this material may get rusty and the brake pad
and disc rotor may be fixed together. This may
cause noise and vibration while driving. Before
parking the vehicle, dry the brake by driving on a
dry road, especially after washing the vehicle or
driving in rain. Contact a GT-R certified NISSAN
dealer if the noise and vibration continue.
Frequent hard braking may cause scorching of
the brake pads. This will require the brake pads
to be replaced, even if the wear limit has not
been reached. Have the brake pads and disc
rotors inspected at the regular vehicle inspections.
For more details, contact a GT-R certified
NISSAN dealer.
If the inside of the disc rotors are cold during the
winter and the surface becomes hot due to a
heavy force being applied repeatedly to the
brakes, cracks may occur near the coolant hole
on the surface of the disc rotor. Cracks may also
occur due to a heavy force being repeatedly
applied to the brakes during high performance
driving. In these cases it may be necessary to
replace the disc rotors or brake pads depending
on the condition of the crack. Contact a GT-R
certified NISSAN dealer for replacement.
REPLACING THE BRAKE PADS
NISSAN generally recommends to replace all
four sets of brake pads and disc rotors at the
same time to maintain maximum brake performance.
However, replacing only the brake pads may be
allowed in some cases (four wheels or only front
wheels depending on the conditions). A GT-R
certified technician must inspect the vehicle and
determine that only the brake pads need to be
replaced. In this case, replacing all brake pads
and disc rotors as a set is not necessary.
Note that the replacement of brake pads and the
disc rotors as a set on all four wheels should be
performed when a GT-R certified technician
determines that this is the correct repair.
8-24 Maintenance and do-it-yourself
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(299,1)
FUSES
2. Open the engine hood and remove the
cover on the battery and the fuse/fusible link
holder.
3. Remove the fuse/fusible link holder cover.
4. Remove the fuse with the fuse puller that is
located in the engine compartment fuse box.
ENGINE COMPARTMENT
CAUTION
Never use a fuse of a higher or lower
amperage rating than that specified on
the fuse box cover. This could damage
the electrical system or cause a fire.
If any electrical equipment does not operate,
check for an open fuse.
A , replace it with a new
5. If the fuse is open *
B . Spare fuses are stored in the
fuses *
passenger compartment fuse box.
6. If a new fuse also opens, have the electrical
system checked and repaired by a GT-R
certified NISSAN dealer.
Fusible links
If any electrical equipment does not operate and
fuses are in good condition, check the fusible
links. If any of these fusible links are melted,
replace only with genuine NISSAN parts.
1. Be sure the ignition switch is pushed to the
OFF or LOCK position and the headlight
switch is turned to OFF.
Maintenance and do-it-yourself 8-25
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(300,1)
2. Open the fuse box lid.
PASSENGER COMPARTMENT
3. Remove the fuse with the fuse puller
A .
*
4. If the fuse is open, replace it with a new fuse.
CAUTION
Never use a fuse of a higher or lower
amperage rating than that specified on
the fuse box cover. This could damage
the electrical system or cause a fire.
If any electrical equipment does not operate,
check for an open fuse.
1. Be sure the ignition switch is pushed to the
OFF or LOCK position and the headlight
switch is turned to OFF.
5. If a new fuse also opens, have the electrical
system checked and repaired by a GT-R
certified NISSAN dealer.
Extended storage fuse switch
To reduce battery drain, the extended storage
fuse switch comes from the factory switched off.
Prior to delivery of your vehicle, the switch is
pushed in (switched on) and should always
remain on.
If any electrical equipment does not operate,
remove the extended storage fuse switch and
8-26 Maintenance and do-it-yourself
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(301,1)
INTELLIGENT KEY BATTERY
REPLACEMENT
check for an open fuse.
NOTE:
If the extended storage fuse switch malfunctions, or if the fuse is open, it is not
necessary to replace the switch. In this
case, remove the extended storage fuse
switch and replace it with a new fuse of the
same rating.
How to remove the extended storage fuse
switch:
1. To remove the extended storage fuse switch,
be sure the ignition switch is in the OFF or
LOCK position.
2. Be sure the headlight switch is in the OFF
position.
3. Remove the fuse box cover.
1 found on each
4. Pinch the locking tabs *
side of the extended storage fuse switch.
5. Pull the extended storage fuse switch
2 .
straight out from the fuse box *
WARNING
Be careful that batteries and other
removed components are not swallowed by children.
NOTICE
There is the possibility that the key may
be damaged when the battery is replaced. It is recommended that you
have the battery replaced by a GT-R
certified NISSAN dealer.
Maintenance and do-it-yourself 8-27
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(302,1)
Recommended battery: Lithium battery CR2032
or an equivalent.
1. Disengage the lock on the reverse side of
the Intelligent Key while pulling out the
mechanical key.
1
2. Insert a flat-bladed screwdriver *
2 and
wrapped with a cloth into the slit *
twist it to separate the case into the upper
and lower parts.
NOTICE
Because there is the risk of scratching
the key, wrap a cloth or similar item
around the screwdriver when separating the parts. If the screwdriver is
inserted too far into the key, it may
damage the internal circuit board.
3. Remove the old battery and insert a new
battery with the + side facing down.
NOTICE
.
.
Be sure that the + and − sides of the
battery are facing in the correct
directions when the battery is inserted.
Do not touch the internal circuits or
electronic terminals. Doing so may
damage them.
4. Reconnect the upper and lower parts of the
Intelligent Key.
See a GT-R certified NISSAN dealer if you
need any assistance for replacement.
NOTE:
After replacing the battery, be sure to
check and check that all Intelligent Key
system functions operate correctly.
FCC Notice:
For USA:
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
8-28 Maintenance and do-it-yourself
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(303,1)
LIGHTS
may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Note: Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s
authority to operate the equipment.
For Canada:
This device complies with Industry Canada
licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must
accept any interference, including interference that may cause undesired operation
of the device.
1.
2.
3.
4.
5.
6.
7.
Headlight (High beam)
Front parking light
Front turn signal light
Daytime running light
Headlight (Low beam)
Front side marker light
High-mounted stop light
8.
9.
License plate light
Rear combination light (rear turn signal/tail/stop/
back-up)
10. Rear side marker light
A : Except for NISMO models
B : NISMO models
*
*
Maintenance and do-it-yourself 8-29
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(304,1)
HEADLIGHTS
Fog may temporarily form inside the lens of the
exterior lights in the rain or in a car wash. A
temperature difference between the inside and
the outside of the lens causes the fog. This does
not indicate that there is a malfunction. If large
drops of water collect inside the lens, contact a
GT-R certified NISSAN dealer.
Replacing
LED headlight:
If replacement is necessary, see a GT-R certified
NISSAN dealer.
EXTERIOR AND INTERIOR LIGHTS
Item
Headlight assembly
Wattage (W)
Bulb No.
low-beam*
LED
—
high-beam*
LED
—
Front turn signal light*
Front parking light*
28
LED
7444NA
—
Daytime running light*
Front side marker light*
Rear combination light*
LED
3.8
—
T10
back-up
16
W16W
turn signal
21
WY21W
stop/tail
LED
—
Rear side marker light*
LED
—
License plate light*
Map light
Vanity mirror light
Step light*
Trunk light*
High-mounted stop light*
5
8
2
2.7
3.4
LED
W5W
—
—
—
—
—
*:
See a GT-R certified NISSAN dealer for replacement.
8-30 Maintenance and do-it-yourself
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(305,1)
Always check with the Parts Department at a
GT-R certified NISSAN dealer for the latest
parts information.
Replacement procedures
All other lights are either type A, B, C, D, E or F.
When replacing a bulb, first remove the lens
and/or cover.
Map light
Vanity mirror light
Maintenance and do-it-yourself 8-31
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(306,1)
WHEELS AND TIRES
If you have a flat tire, see the following
section. (
“Flat tire” page 6-3)
CAUTION
A GT-R certified NISSAN dealer should
perform a tire change. It will be necessary to reset the tire pressure sensors.
To change the tires, contact a GT-R
certified NISSAN dealer.
NOTICE
Make sure the tire valve stem cap is
installed and that the valve stem is
tight. When installing the cap, make
sure to tighten the cap by hand. If a tool
is used to tighten the cap, the cap may
be damaged.
TIRE PRESSURE
Be sure to use the tires and wheels together as
a set that are designated for use with this
vehicle.
When tire replacement is required, replacing the
tires as a set of four with new tires is
recommended. However, if a tire is punctured
or damaged, it may be possible to replace only
the damaged tire. Determining whether one tire
or a complete set of tires should be replaced is
based on a number of factors including tire wear
and condition. Contact your GT-R certified
NISSAN dealer. They can recommend if an
individual tire or a complete set should be
replaced.
Tire Pressure Monitoring System
(TPMS)
This vehicle is equipped with the Tire Pressure
Monitoring System (TPMS). It monitors tire
pressure of all tires. When the low tire pressure
warning light is lit, one or more of your tires is
significantly under-inflated. The system also
displays pressure of all tires on the multi function
display by sending a signal from a sensor that is
installed in each wheel.
The TPMS will activate only when the vehicle is
driven at speeds above 16 MPH (25 km/h).
Also, this system may not detect a sudden drop
in tire pressure. (
“Low tire pressure warning light” page 2-27) (
“Tire Pressure
Monitoring System (TPMS)” page 5-4)
(
“Flat tire” page 6-3)
Tire inflation pressure
Check the tire pressure often and always
prior to long distance trips. The recommended tire pressure specifications are
shown on the F.M.V.S.S./C.M.V.S.S. label
or the Tire and Loading Information label (if
so equipped) under the “Cold Tire Pressure” heading. The Tire and Loading
Information label is affixed to the driver
side door end. Tire pressures should be
checked regularly because:
. Most tires naturally lose air over time.
. Tires can lose air suddenly when driven
over potholes or other objects or if the
vehicle strikes a curb while parking.
NOTE:
. You can check the pressure of all four
tires on the multi function display. See
the separate Multi Function Display
Owner’s Manual.
.
The tires of this vehicle are filled with
nitrogen gas. When the tire pressure is
low, fill the tires with nitrogen. Contact
a GT-R certified NISSAN dealer for
information on filling the tires with
nitrogen.
8-32 Maintenance and do-it-yourself
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(307,1)
.
If nitrogen is not available, compressed
air may be safely used under normal
driving conditions. However, NISSAN
recommends refilling with nitrogen for
maximum tire performance.
The tire pressures should be checked
when the tires are cold. The tires are
considered COLD after the vehicle has
been parked for 3 or more hours, or driven
less than 1 mile (1.6 km) at moderate
speeds.
Incorrect tire pressure, including under inflation, may adversely affect tire
life and vehicle handling.
.
WARNING
.
.
Improperly inflated tires can fail
suddenly and cause an accident.
The Gross Vehicle Weight rating
(GVWR) is located on the F.M.V.
S.S./C.M.V.S.S. certification label. The vehicle weight capacity
is indicated on the Tire and
Loading Information label (if so
equipped). Do not load your
.
vehicle beyond this capacity.
Overloading your vehicle may
result in reduced tire life, unsafe
operating conditions due to premature tire failure, or unfavorable handling characteristics
and could also lead to a serious
accident. Loading beyond the
specified capacity may also result in failure of other vehicle
components.
Before taking a long trip, or
whenever you heavily load your
vehicle, use a tire pressure
gauge to ensure that the tire
pressures are at the specified
level.
For additional information regarding tires, refer to “Important
Tire Safety Information” (US) or
“Tire Safety Information” (Canada) in the Warranty Information
Booklet.
NOTE:
. Use only genuine GT-R tires and road
wheels.
The GT-R uses specially designed runflat tires and matching road wheels.
Use of these specially developed tires
and wheels provides the greatest potential for maximum performance.
— Genuine GT-R tires and road wheels
help achieve maximum cornering
and braking performance.
— Genuine GT-R tires and road wheels
help achieve maximum tire durability during acceleration.
— Genuine GT-R tires and road wheels
help achieve maximum handling
capability during performance driving.
— Genuine GT-R tires and road wheels
help provide road holding in the
event of decreasing tire pressure
and punctures.
— Genuine GT-R tires and road wheels
help prevent the decrease of
straight-running stability caused by
uneven tire wear due to high rigidity
wheels and wide tires.
.
The GT-R uses specially designed runflat tires which feature an extremely
Maintenance and do-it-yourself 8-33
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(308,1)
rigid side wall. Special techniques and
equipment are therefore required when
replacing these tires. NISSAN recommends that tire replacement be performed at a GT-R certified NISSAN
dealer.
.
Specific tire changing equipment must
be used to remove the GT-R tires from
the wheel and to install the GT-R tires
onto the wheel. It is only possible to
reuse the tires when they have no
cracks and/or deformations on the
bead portion of the tire. If the incorrect
equipment is used to remove the GT-R
tires from the wheel and to install the
GT-R tires onto the wheel, cracks and
deformation may occur on the bead
portion of the tires meaning that the
tires cannot be reused. Contact a GT-R
certified NISSAN dealer if the tires
need to be removed from the wheels.
8-34 Maintenance and do-it-yourself
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(309,1)
TIRE AND LOADING INFORMATION
LABEL
1
*
2
*
3
*
4
*
5
*
6
*
Seating capacity: The maximum number of occupants that can be seated in
the vehicle.
Vehicle load limit: See the following
section. (
“Vehicle loading information” page 9-14)
Original size: The size of the tires
originally installed on the vehicle at the
factory.
Cold tire pressure: Inflate the tires to
this pressure when the tires are cold.
Tires are considered COLD after the
vehicle has been parked for 3 or more
hours, or driven less than 1 mile (1.6
km) at moderate speeds. The recommended cold tire inflation is set by the
manufacturer to provide the best
balance of tire wear, vehicle handling,
driveability, tire noise, etc., up to the
vehicle’s GVWR.
Tire size — see the following section.
(
“Tire labeling” page 8-37)
Spare tire size or compact spare tire
size (if so equipped)
Maintenance and do-it-yourself 8-35
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(310,1)
tion shown on the Tire and Loading
Information label.
5. Add air to the tire as needed. If too
much air is added, press the core of the
valve stem briefly with the tip of the
gauge stem to release pressure. Recheck the pressure and add or release
air as needed.
6. Install the valve stem cap.
7. Check the pressure of all other tires.
NOTE:
. You can check the pressure of all
CHECKING THE TIRE PRESSURE
1. Remove the valve stem cap from the
tire.
2. Press the pressure gauge squarely onto
the valve stem. Do not press too hard or
force the valve stem sideways, or air will
escape. If the hissing sound of air
escaping from the tire is heard while
checking the pressure, reposition the
gauge to eliminate this leakage.
3. Remove the gauge.
4. Read the tire pressure on the gauge
stem and compare it to the specifica-
.
.
four tires on the multi function
display. See the separate Multi
Function Display Owner’s Manual.
The tires of this vehicle are filled
with nitrogen gas. When the tire
pressure is low, fill the tires with
nitrogen. Contact a GT-R certified
NISSAN dealer for information on
filling the tires with nitrogen.
If nitrogen is not available, compressed air may be safely used
under normal driving conditions.
However, NISSAN recommends re-
filling with nitrogen for maximum
tire performance.
Summer tires:
SIZE
FRONT ORI- 255/40ZRGINAL TIRE F20 (97Y)
REAR ORI- 285/35ZRGINAL TIRE F20 (100Y)
COLD TIRE
INFLATION
PRESSURE
30 PSI (210
kPa)
29 PSI (200
kPa)
All-season tires:
SIZE
COLD TIRE
INFLATION
PRESSURE
FRONT ORI- 255/40RF20 32 PSI (220
GINAL TIRE 97W
kPa)
REAR ORI- 285/35RF20 30 PSI (210
kPa)
GINAL TIRE 100W
8-36 Maintenance and do-it-yourself
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(311,1)
5. Two-digit number (15): This number is
the wheel or rim diameter in inches.
6. Two- or three-digit number (95): This
number is the tire’s load index. It is a
measurement of how much weight each
tire can support. You may not find this
information on all tires because it is not
required by law.
7. H: Tire speed rating. You should not
drive the vehicle faster than the tire
speed rating.
Example
TIRE LABELING
Federal law requires tire manufacturers to
place standardized information on the sidewall of all tires. This information identifies
and describes the fundamental characteristics of the tire and also provides the tire
identification number (TIN) for safety standard certification. The TIN can be used to
identify the tire in case of a recall.
Example
1
*
Tire size (example: P215/60R16 94H)
1. P: The “P” indicates the tire is designed
for passenger vehicles. (Not all tires
have this information.)
2. Three-digit number (215): This number
gives the width in millimeters of the tire
from sidewall edge to sidewall edge.
3. Two-digit number (65): This number,
known as the aspect ratio, gives the
tire’s ratio of height to width.
4. R: The “R” stands for radial.
F: The “F” after “R” indicates SelfSupporting type run-flat tire.
Maintenance and do-it-yourself 8-37
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(312,1)
year the tire was built. For example, the
numbers 3103 means the 31st week of
2003. If these numbers are missing,
then look on the other sidewall of the
tire.
3
*
Tire ply composition and material
The number of layers or plies of rubbercoated fabric in the tire.
Tire manufacturers also must indicate the
materials in the tire, which include steel,
nylon, polyester, and others.
4
*
Example
2
*
TIN (Tire Identification Number) for a new
tire (example: DOT XX XX XXX XXXX)
1. DOT: Abbreviation for the “Department
2.
3.
4.
5.
6.
of Transportation”. The symbol can be
placed above, below or to the left or
right of the Tire Identification Number.
Two-digit code: Manufacturer’s identification mark
Two-digit code: Tire size
Three-digit code: Tire type code (Optional)
Three-digit code: Date of Manufacture
Four numbers represent the week and
Maximum permissible inflation pressure
This number is the greatest amount of air
pressure that should be put in the tire. Do
not exceed the maximum permissible inflation pressure.
5
*
Maximum load rating
This number indicates the maximum load in
kilograms and pounds that can be carried
by the tire. When replacing the tires on the
vehicle, always use a tire that has the same
load rating as the factory installed tire.
*
6
Term of “tubeless” or “tube type”
Indicates whether the tire requires an inner
tube (“tube type”) or not (“tubeless”).
7
*
The word “radial”
The word “radial” is shown, if the tire has
radial structure.
8
*
Manufacturer or brand name
Manufacturer or brand name is shown.
Other tire-related terminology:
In addition to the many terms that are
defined throughout this section, Intended
Outboard Sidewall is (1) the sidewall that
contains a whitewall, bears white lettering
or bears manufacturer, brand and/or model
name molding that is higher or deeper than
the same molding on the other sidewall of
the tire, or (2) the outward facing sidewall
of an asymmetrical tire that has a particular
side that must always face outward when
mounted on a vehicle.
TYPES OF TIRES
WARNING
.
When changing or replacing tires,
be sure all four tires are of the same
type (Examples: Summer or All
Season) and construction. A GT-R
certified NISSAN dealer may be able
8-38 Maintenance and do-it-yourself
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(313,1)
to help you with information about
tire type, size, speed rating and
availability.
.
.
Replacing tires with those not originally specified by NISSAN could
affect the proper operation of the
TPMS.
For additional information regarding tires, refer to “Important Tire
Safety Information” (US) or “Tire
Safety Information” (Canada) in the
Warranty Information Booklet.
wheels if you plan to operate your vehicle in
snowy or icy conditions when temperatures are
less than 328F (08C).
WARNING
Never use summer tires when the
temperature is below −48F (−208C) to
prevent permanent tread deformation
which may cause tire damage or tire
failure. This may cause a loss of vehicle
control which can result in serious
personal injury or death.
All-season tires
Run-flat tires
NISSAN specifies all-season tires on some
models to provide good performance for use
all year around, including snowy and icy road
conditions. All-season tires are identified by ALL
SEASON on the tire sidewall.
Your vehicle is equipped with run-flat tires. You
can continue driving to a safe location even if
they are punctured. Always use run-flat tires of
the specified size on all four wheels. Mixing tire
sizes or construction may reduce vehicle handling stability. If necessary, contact a GT-R
certified NISSAN dealer for assistance.
Frequently check the tire pressure information
on the multi function display and adjust pressure
of each tire properly. See the separate Multi
Function Display Owner’s Manual.
It can be difficult to tell if a run-flat tire is underinflated or flat. Check the tire pressures as
Summer tires
The GT-R summer tires are made from a
specially formulated rubber to maximize the
vehicle’s performance capabilities. Performance
of summer tires is substantially reduced when
temperatures are less than 328F (08C) so you
must drive carefully. NISSAN recommends the
use of winter or all-season tires on all four
described earlier in this section. If the tire
becomes under-inflated while driving, the low
tire pressure warning light will come on. If the
tire becomes flat while driving, the low tire
pressure warning light and the run-flat tire
warning display will come on.
Low tire pressure:
If the vehicle is being driven with low tire
pressure, the low tire pressure warning light will
illuminate and the low tire pressure warning will
appear in the vehicle information display.
Flat tire:
If the vehicle is being driven with one or more flat
tires, the low tire pressure warning light will
illuminate continuously and a chime will sound
for 10 seconds. The run-flat tire warning also
appears in the vehicle information display.
The chime will only sound at the first indication
of a flat tire and the run-flat tire warning display
will illuminate continuously. When the flat tire
warning is activated, have the system reset and
the tire checked and replaced if necessary by a
GT-R certified NISSAN dealer. Even if the tire is
inflated to the specified COLD tire pressure, the
warning light will continue to illuminate until the
system is reset by a GT-R certified NISSAN
dealer.
If the low tire pressure and the run-flat tire
Maintenance and do-it-yourself 8-39
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(314,1)
warning appears on the vehicle information
display:
.
Do not exceed 50 MPH (80 km/h).
.
Increase your following distance to allow for
increased stopping distances.
.
Avoid sudden maneuvers, hard cornering
and hard braking.
WARNING
.
.
.
Although you can continue driving
with a punctured run-flat tire, remember that vehicle handling stability is reduced, which could lead to
an accident and personal injury.
Also, driving a long distance at high
speeds may damage the tire.
Do not drive at speeds above 50
MPH (80 km/h) and do not drive
more than 50 miles (80 km) with a
punctured run-flat tire. The actual
distance the vehicle can be driven
on a flat tire depends on outside
temperature, vehicle load, road conditions and other factors.
Drive safely at reduced speeds.
Avoid hard cornering or braking,
which may cause you to lose control
of the vehicle.
NOTICE
.
Never install tire chains on a punctured run-flat tire, as this could
damage your vehicle.
.
Avoid driving over any projection or
pothole, as the clearance between
the vehicle and the ground is smaller than normal.
.
Do not enter an automated car wash
with a punctured run-flat tire.
.
Have the punctured tire replaced by
a GT-R certified NISSAN dealer as
soon as possible, as the tire’s
performance capability is reduced.
Tires for All-Wheel Drive (AWD)
If excessive tire wear is found, it is recommended that all four tires be replaced with tires
of the specified size, brand, construction and
tread pattern. The tire pressure and wheel
alignment should also be checked and corrected as necessary. Contact a GT-R certified
NISSAN dealer.
TIRE CHAINS
Use of tire chains may be prohibited according
to location. Check the local laws before installing tire chains. When installing tire chains, make
sure they are of proper size for the tires on your
vehicle and are installed according to the chain
manufacturer instructions. Use only SAE class
S chains. Class “S” chains are used on vehicles
with restricted tire to vehicle clearance. Vehicles
that can use Class “S” chains are designed to
meet the SAE standard minimum clearances
between the tire and the closest vehicle
suspension or body component required to
accommodate the use of a winter traction device
(tire chains or cables). The minimum clearances
are determined using the factory equipped tire
size. Other types may damage your vehicle. Use
chain tensioners when recommended by the tire
chain manufacturer to ensure a tight fit. Loose
end links of the tire chain must be secured or
removed to prevent the possibility of whipping
action damage to the fenders or undercarriage.
If possible, avoid fully loading your vehicle when
using tire chains. In addition, drive at a reduced
speed. Otherwise, your vehicle may be damaged and/or vehicle handling and performance
may be adversely affected.
8-40 Maintenance and do-it-yourself
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(315,1)
NOTE:
Tire chains must be installed only on the
rear wheels and not on the front wheels.
CAUTION
Do not use tire chains on dry roads.
CHANGING WHEELS AND TIRES
Tire rotation
Tires cannot be rotated because your
vehicle is equipped with different sized
tires in the front and rear.
NOTICE
Never install tire chains on a punctured
run-flat tire, as this could damage your
vehicle.
Do not drive with tire chains on paved roads that
are clear of snow. Driving with chains in such
conditions can cause damage to the various
mechanisms of the vehicle due to some
overstress.
1.
2.
Wear indicator
Location mark
Tire wear and damage
WARNING
.
.
Tires should be periodically inspected for wear, cracking, bulging or objects caught in the
tread. If excessive wear, cracks,
bulging or deep cuts are found,
the tire(s) should be replaced.
The original tires have built-in
tread wear indicators. When the
Maintenance and do-it-yourself 8-41
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(316,1)
.
.
wear indicators are visible, the
tire(s) should be replaced.
Tires degrade with age and use.
Have tires, over 6 years old
checked by a qualified technician because some tire damage
may not be obvious. Replace the
tires as necessary to prevent tire
failure and possible personal
injury.
For additional information regarding tires, refer to “Important
Tire Safety Information” (US) or
“Tire Safety Information” (Canada) in the Warranty Information
Booklet.
NISSAN dealer. They can recommend if an
individual tire or a complete set should be
replaced.
When replacing a tire, use the specified size,
speed rating and load carrying capacity as
originally equipped. (
“Wheels and tires”
page 9-9)
.
NOTICE
.
When you replace the GT-R tires, it
is recommended that you replace all
the tires at the same time.
.
The GT-R uses specially designed
run-flat tires which feature an extremely rigid side wall. Special techniques and equipment are therefore
required when replacing these tires.
NISSAN recommends that tire replacement be performed at a GT-R
certified NISSAN dealer.
Replacing wheels and tires
When tire replacement is required, replacing
tires as a set of four with new tires is
recommended. However, if a tire is punctured
or damaged, it may be possible to replace only
the damaged tire. Determining whether one tire
or a complete set of tires should be replaced is
based on a number of factors including tire wear
and condition. Contact your GT-R certified
changer, cracks and deformation
may occur on the bead portion of
the tires meaning that the tires
cannot be reused.
.
When tires are reinstalled after
being uninstalled from the wheels,
use equipment such as a leverless
automatic tire changer. It is only
possible to reuse the tires when
they have no cracks and/or deformations on the bead portion. However, if you use a lever-type tire
Make sure the tire valve stem cap is
installed and that the valve stem is
tight. When installing the cap, make
sure to tighten the cap by hand. If a
tool is used to tighten the cap, the
cap may be damaged.
WARNING
.
The use of tires other than those
specified or the mixed use of tires of
different brands, construction (bias,
bias-belted, radial or run-flat), or
tread patterns can adversely affect
the ride, braking, VDC system, handling, ground clearance, body-to-tire
clearance, tire chain clearance,
speedometer calibration, headlight
aim and bumper height. Some of
these effects may lead to accidents
and could result in serious personal
injury.
.
If the wheels are changed for any
reason, always replace with wheels
8-42 Maintenance and do-it-yourself
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(317,1)
which have the same off-set dimension. Wheels of a different off-set
could cause premature tire wear,
degrade vehicle handling characteristics, affect the VDC system and/or
cause interference with the brake
discs. Such interference can lead to
decreased braking efficiency and/or
early brake pad wear. (
“Wheels
and tires” page 9-9)
.
When a wheel is replaced, tire
pressure will not be indicated, the
TPMS will not function and the low
tire pressure warning light will flash
for approximately 1 minute and
remain on after the 1 minute. Contact a GT-R certified NISSAN dealer
as soon as possible for tire replacement and/or system resetting.
.
Replacing tires with those not originally specified by NISSAN could
affect the proper operation of the
TPMS.
.
Do not install a damaged or deformed wheel or tire even if it has
been repaired. Such wheels or tires
could have structural damage and
could fail without warning.
.
Never use retread tires.
.
For additional information regarding tires, refer to “Important Tire
Safety Information” (US) or “Tire
Safety Information” (Canada) in the
Warranty Information Booklet.
.
Always use tires of the specified
type, size, brand, construction (bias,
bias-belted, radial or run-flat), and
tread pattern on all four wheels.
Failure to do so may result in a
circumference difference between
tires on the front and rear axles
which will cause excessive tire wear
and may damage the transmission,
transfer case and differential gears.
Wheel balance
Unbalanced wheels may affect vehicle handling
and tire life. Even with regular use, wheels can
get out of balance. Therefore, they should be
balanced as required.
Wheel balance service should be performed
with the wheels off the vehicle. Spin balancing
the rear wheels on the vehicle could lead to
mechanical damage.
For additional information regarding tires, refer
to “Important Tire Safety Information” (US) or
“Tire Safety Information” (Canada) in the Warranty Information Booklet.
Care of wheels
(
“Cleaning exterior” page 7-2)
JACKING VEHICLE AND REMOVING
WHEELS
WARNING
.
Make sure the parking brake is
securely applied and the transmisP position.
sion is shifted into the &
.
Never change tires when the vehicle
is on a slope, ice or slippery areas.
This is hazardous.
.
Never change tires if oncoming
traffic is close to your vehicle. Wait
for professional road assistance.
Maintenance and do-it-yourself 8-43
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(318,1)
CAUTION
After using the tools, put them back in
their original places. An accident may
occur if you leave them in the car
unsecured.
Jacking up the vehicle and removing
the tire
WARNING
Blocking wheels
1 at both the front and
Place suitable blocks *
back of the wheel diagonally opposite the flat
tire to prevent the vehicle from moving when it is
jacked up.
WARNING
Be sure to block the wheel as the
vehicle may move and result in personal
injury.
.
Never get under the vehicle while it
is supported only by the jack. If it is
necessary to work under the vehicle,
support it with safety stands.
.
Use the correct jack-up points.
Never use any other part of the
vehicle for jack support.
.
Never jack up the vehicle more than
necessary.
.
Never use blocks on or under the
jack.
.
Do not start or run the engine while
vehicle is on the jack, as it may
cause the vehicle to move. This is
especially true for vehicles with
Getting the tools
NOTE:
A jack, jack lever and rod are not equipped
as standard with this vehicle. These parts
are dealer options. Contact a GT-R certified NISSAN dealer about acquiring a jack,
jack lever and rod. You can store a jack,
jack lever and rod in the floor in front of
the passenger’s seat.
8-44 Maintenance and do-it-yourself
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(319,1)
limited slip differentials.
.
Do not allow passengers to stay in
the vehicle while it is on the jack.
Carefully read the caution label attached
to the jack body and the following instructions.
Jack-up point
1. Place the jack directly under the jack-up
point as illustrated so the top of the jack
contacts the vehicle at the jack-up point.
The jack should be used on level firm
ground.
Maintenance and do-it-yourself 8-45
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(320,1)
A of the
2. Fit the jack head into the recess *
jack-up point by turning the jackscrew
clockwise with your fingers.
3. Loosen each wheel nut one or two turns by
turning counterclockwise with the wheel nut
wrench. Do not remove the wheel nuts
until the tire is off the ground.
4. Carefully raise the vehicle until the tire clears
the ground. To lift the vehicle, securely hold
the jack lever and rod with both hands as
shown above.
8-46 Maintenance and do-it-yourself
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(321,1)
5. Remove the wheel nuts and then remove the
wheel.
NOTE:
When putting a wheel on the ground,
put it down with the outer side of the
wheel facing up to prevent scratching
of the wheel surface.
6. Clean any mud or dirt from the surface
1 and wheel
between the brake disc rotor *
2 .
*
7. Tighten the wheel nuts by hand by turning
A of
them clockwise until the tapered part *
B of
each nut lightly contacts the seat part *
the wheel hole.
When replacing a front wheel, make sure the
hole in the wheel is aligned with the pin on
the brake disc rotor.
Maintenance and do-it-yourself 8-47
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(322,1)
Wheel nut tightening torque:
WARNING
8. With the wheel nut wrench, tighten wheel
nuts alternately and evenly in the sequence
1 , *
2 , *
3 , *
4 , *
5 ) until
as illustrated (*
they are tight.
9. Lower the vehicle slowly until the tire
touches the ground. Then, with the wheel
nut wrench, tighten the wheel nuts securely
in the sequence as illustrated. Lower the
vehicle completely.
.
Incorrect wheel nuts or improperly
tightened wheel nuts can cause the
wheel to become loose or come off.
This could cause an accident.
.
Do not use oil or grease on the
wheel studs or nuts. This could
cause the nuts to become loose.
.
Retighten the wheel nuts when the
vehicle has been driven for 600
miles (1,000 km).
WARNING
If the road wheels are hot, allow them
to cool sufficiently before tightening
the wheel nuts. Otherwise, the wheel
nuts cannot be tightened to specification.
Except for NISMO models
97 ft-lb (132 N·m)
NISMO models
114 ft-lb (155 N·m)
.
The wheel nuts must be kept tightened to specification at all times. It
is recommended that wheel nuts be
tightened to specifications at each
lubrication interval.
Adjust tire pressure to the COLD
pressure.
COLD pressure: After the vehicle has
been parked for three hours or more
or driven less than 1 mile (1.6 km).
COLD tire pressures are shown on
the Tire and Loading Information
label affixed to the driver’s door
opening.
10. Securely store the jacking equipment in the
vehicle.
NOTE:
. As soon as possible, tighten the
wheel nuts to the specified torque
with a torque wrench.
8-48 Maintenance and do-it-yourself
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(323,1)
WHEEL LOCK NUTS (if so equipped)
In order to prevent theft, the specially designed
1 is installed on each wheel.
wheel lock nut *
The wheel lock nut cannot be removed with
commonly used tools.
When removing tires, use the lock key
provided with your vehicle.
2
*
NOTE:
. The wheel lock nut has an individual
code. A lock key which does not match
the individual code cannot remove the
wheel lock nut. If you lose the wheel
lock key, contact a GT-R certified
NISSAN dealer immediately.
.
3 in a safe
Keep the key code card *
place. To purchase a lock key, contact a
GT-R certified NISSAN dealer with your
4 on the key code card.
original code *
.
When you ask for a service at a GT-R
certified NISSAN dealer, make sure to
keep the lock key in the vehicle. Otherwise, tires cannot be removed and any
service requiring the removal of the
wheels cannot be performed.
Removing the wheel lock nut
To remove the wheel lock nut, use the lock key
stored under the passenger’s side floor.
1. Insert the lock key to the wheel lock nut.
2. To remove the wheel lock nut, turn the lock
key counterclockwise using the wheel nut
wrench.
CAUTION
.
Do not use a power tool to remove
the wheel lock nuts.
.
Tighten the wheel lock nuts to the
same tightening torque as the normal wheel nuts. (
“Jacking up
the vehicle and removing the tire”
page 8-44)
Maintenance and do-it-yourself 8-49
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(324,1)
MEMO
8-50 Maintenance and do-it-yourself
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(325,1)
9 Technical and consumer information
Capacities and recommended fluids/lubricants ............... 9-2
Fuel information .................................................................. 9-4
Engine oil and oil filter recommendation ...................... 9-6
Air conditioning system refrigerant and
lubricant recommendations .............................................. 9-7
Specifications ............................................................................ 9-8
Engine ................................................................................... 9-8
Wheels and tires ................................................................ 9-9
Dimensions ....................................................................... 9-10
When traveling or registering in another country ......... 9-11
Vehicle identification ............................................................. 9-11
Vehicle Identification Number (VIN) plate ................. 9-11
Vehicle identification number (chassis number) ..... 9-11
Engine serial number ...................................................... 9-12
F.M.V.S.S./C.M.V.S.S. certification label ................... 9-12
Emission control information label .............................. 9-12
Tire and loading information label ............................... 9-13
Air conditioner specification label ............................... 9-13
Installing front license plate ................................................ 9-13
Vehicle loading information ................................................
Terms ................................................................................
Vehicle load capacity ...................................................
Loading tips ....................................................................
Measurement of weights .............................................
Towing a trailer ......................................................................
Flat towing ..............................................................................
Uniform tire quality grading ................................................
Treadwear .......................................................................
Traction AA, A, B and C .............................................
Temperature A, B and C .............................................
Emission control system warranty ....................................
Reporting safety defects ....................................................
Readiness for Inspection/Maintenance (I/M) test
(US only) ................................................................................
Event Data Recorders (EDR) ............................................
Vehicle status data recorder (VSDR) .............................
Handling of data ............................................................
Owner’s Manual/Service Manual order information ....
[ Edit: 2014/ 12/ 8
9-14
9-14
9-15
9-16
9-16
9-17
9-17
9-17
9-17
9-18
9-18
9-18
9-19
9-20
9-20
9-21
9-21
9-22
Model: R35-D ]
(326,1)
CAPACITIES AND RECOMMENDED
FLUIDS/LUBRICANTS
The following are approximate capacities. The actual refill capacities may be a little different. When refilling, follow the procedure
instructed in the “8. Maintenance and do-it-yourself” section to determine the proper refill capacity.
Capacity (Approximate)
Recommended specifications
US measure
Imp measure
Liter
19-1/2 gal
16-1/4 gal
73.8
With oil filter change
5-1/4 qt
4-3/8 qt
5.0
Without oil filter change
4-3/4 qt
4 qt
4.5
Fuel
Engine oil*
Drain and refill
.
.
.
*For additional information, see
“Changing engine oil and
filter” page 8-14.
.
“Fuel information” page 9-4)
(
Mobil 1 (0W-40)
Mobil 1 (0W-40) (100% synthetic) is the factory fill oil. The VR38
engine with its plasma-sprayed bores was developed using this oil.
NISSAN cannot ensure proper engine operation and durability if other
0W-40 synthetic oil is used. If Mobil 1 (0W-40) is not available, Mobil
1 (10W-40) (100% synthetic) may be used; however, some
performance loss may be noticed. For additional information, see the
following section. (
“Engine oil and oil filter recommendation”
page 9-6)
The recommended oil capacity level is 0.39 in (10mm) (0.5 L) below
the H mark on the engine oil dipstick. For additional information, see
the following section. (
“Engine oil” page 8-13)
Cooling system
With reservoir (except for NISMO models)
With reservoir (NISMO models)
12 qt
10 qt
11.3
12-3/8 qt
10-1/4 qt
11.7
Reservoir (except for NISMO models)
1-1/2 qt
1-1/4 qt
1.4
Reservoir (NISMO models)
1-7/8 qt
1-5/8 qt
1.8
Transmission oil (Drain and refill)
10 qt
8-1/4 qt
.
.
Genuine NISSAN Long Life Antifreeze/Coolant (blue) or equivalent
For additional information, see the following section. (
“Engine
cooling system” page 8-10)
.
.
Genuine NISSAN Transmission Oil R35 Special
The use of fluids and lubricants other than the specified may cause
vehicle malfunctions and result in non-warranty vehicle repairs.
All of the fluid cannot be removed when servicing the transmission.
The actual refill amount may be less than shown.
Genuine NISSAN Differential Oil R35 COMPETITION type 2189E
The use of fluids and lubricants other than the specified may cause
vehicle malfunctions and result in non-warranty vehicle repairs.
Genuine NISSAN PSF or equivalent
DEXRONTM VI type ATF may also be used.
9.4
.
Differential oil
(Drain and refill)
Front
1-3/8 pt
1-1/8 pt
0.65
Rear
2-7/8 pt
2-3/8 pt
1.35
Power steering fluid (PSF)
9-2
.
.
Refill to the proper oil level according to the instruc- .
tions in the “8. Maintenance and do-it-yourself” section. .
Technical and consumer information
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(327,1)
.
.
Brake fluid
Refill to the proper oil level according to the instructions in the “8. Maintenance and do-it-yourself” section.
Multi-purpose grease
—
—
—
Air conditioning system refrigerant
—
—
—
Air conditioning system lubricants
—
—
—
Window washer fluid
—
—
—
.
.
.
.
.
Genuine NISSAN Brake Fluid R35 Special II
Genuine NISSAN Brake Fluid R35 Special II is the factory fill brake
fluid. The Vehicle Dynamic Control (VDC) unit and other related parts
were specially designed for this brake fluid and NISSAN cannot
ensure the best performance and proper operation of the vehicle if
other brake fluid is used.
NLGI No. 2 (Lithium soap base)
HFC-134a (R-134a)
“Air
For additional information, see the following section. (
conditioner specification label” page 9-13)
NISSAN UV Luminous Oil Type S or exact equivalent
Genuine NISSAN Windshield Washer Concentrate Cleaner &
Antifreeze or equivalent
Technical and consumer information 9-3
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(328,1)
FUEL INFORMATION
15 or E-85 fuel in a vehicle not
specifically designed for E-15 or E85 fuel can adversely affect the
emission control devices and systems of the vehicle. Damage caused
by such fuel is not covered by the
NISSAN new vehicle limited warranty.
VR38 engine
Use unleaded premium gasoline with an octane
rating of at least 93 AKI (Anti-Knock Index)
number (Research octane number 98) to maximize vehicle performance.
If the premium gasoline specified above is not
available, you may use unleaded premium gasoline with an octane rating of at least 91 AKI
number (Research octane number 96), but you
may notice a decrease in performance.
.
Do not use gasoline with an octane rating lower
than 91 AKI (Research octane number 96).
NOTICE
.
Using a fuel other than that specified could adversely affect the emission control system, and may also
affect warranty coverage.
.
Under no circumstances should a
leaded gasoline be used, because
this will damage the three-way catalyst.
.
Do not use E-15 or E-85 fuel in your
vehicle. Your vehicle is not designed
to run on E-15 or E-85 fuel. Using E-
9-4
.
U.S. government regulations require
ethanol dispensing pumps to be
identified by a small, square, orange
and black label with the common
abbreviation or the appropriate percentage for that region.
NISSAN recommends using fuels
that contain no alcohol. However,
fuels containing up to 10% alcohol
may be used, if necessary. To avoid
serious engine damage due to increased cylinder temperatures, do
not use fuels that contain more
alcohol than indicated in this section. Also, do not use fuel additives,
fuel stabilizers or fuel deicers that
contain alcohol.
Gasoline specifications
NISSAN recommends using gasoline that meets
the World-Wide Fuel Charter (WWFC) specifications where it is available. Many of the
automobile manufacturers developed this specification to improve emission system and
vehicle performance. Ask your service station
manager if the gasoline meets the World-Wide
Fuel Charter (WWFC) specifications.
Reformulated gasoline
Some fuel suppliers are now producing reformulated gasolines. These gasolines are specially
designed to reduce vehicle emissions. NISSAN
supports efforts towards cleaner air and suggests that you use reformulated gasoline when
available.
Gasoline containing oxygenates
Some fuel suppliers sell gasoline containing
oxygenates such as ethanol, MTBE and methanol with or without advertising their presence.
NISSAN does not recommend the use of fuels
of which the oxygenate content and the fuel
compatibility for your NISSAN cannot be readily
determined. If in doubt, ask your service station
manager.
If you use oxygenate-blend gasoline, please take
the following precautions as the usage of such
Technical and consumer information
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(329,1)
fuels may cause vehicle performance problems
and/or fuel system damage.
.
The fuel should be unleaded and have
an octane rating no lower than that
recommended for unleaded gasoline.
.
If an oxygenate-blend, excepting a
methanol blend, is used, it should
contain no more than 10% oxygenate.
(MTBE may, however, be added up to
15%.)
.
.
E-15 fuel contains more than 10%
oxygenate. E-15 fuel will adversely
affect the emission control devices
and systems of the vehicle and should
not be used. Damage caused by such
fuel is not covered under the NISSAN
new vehicle limited warranty.
If a methanol blend is used, it should
contain no more than 5% methanol
(methyl alcohol and wood alcohol). It
should also contain a suitable amount
of appropriate cosolvents and corrosion inhibitors. If not properly formulated with the appropriate cosolvents
and corrosion inhibitors, such methanol blends may cause fuel system
damage and/or vehicle performance
malfunctions. At this time, sufficient
data is not available to ensure that all
methanol blends are suitable for use in
NISSAN vehicles.
If any undesirable driveability problems such as
engine stalling or hard hot starting are experienced after using oxygenate-blend fuels, immediately change to a non-oxygenate fuel or a
fuel with a low blend of MTBE.
NOTICE
Take care not to spill gasoline during
refueling. Gasoline containing oxygenates can cause paint damage.
E-15 fuel
E-15 fuel is a mixture of approximately 15% fuel
ethanol and 85% unleaded gasoline. E-15 can
only be used in vehicles designed to run on E15 fuel. Do not use E-15 in your vehicle. U.S.
government regulations require fuel ethanol
dispensing pumps to be identified with small,
square, orange and black label with the common
abbreviation or the appropriate percentage for
that region.
E-85 fuel
E-85 fuel is a mixture of approximately 85% fuel
ethanol and 15% unleaded gasoline. E-85 can
only be used in a Flexible Fuel Vehicle (FFV). Do
not use E-85 fuel in your vehicle. U.S. government regulations require fuel ethanol dispensing
pumps to be identified by a small, square,
orange and black label with the common
abbreviation or the appropriate percentage for
that region.
Aftermarket fuel additives
NOTICE
NISSAN does not recommend the use
of any aftermarket fuel additives (Example: fuel injector cleaner, intake
valve deposit removers, etc.) which are
sold commercially. Many of these additives intended for gum, varnish or
deposit removal may contain active
solvent or similar ingredients that can
be harmful to the fuel system and
engine.
Technical and consumer information 9-5
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(330,1)
Octane rating tips
Using unleaded gasoline with an octane
rating lower than recommended above can
cause persistent, heavy spark knock.
(Spark knock is a metallic rapping noise.)
If severe, this can lead to engine damage.
If you detect a persistent heavy spark
knock even when using gasoline of the
stated octane rating, or if you hear steady
spark knock while holding a steady speed
on level roads, have a GT-R certified
NISSAN dealer correct the condition. Failure to correct the condition is misuse of
the vehicle, for which NISSAN is not
responsible.
Incorrect ignition timing will result in knocking,
after-run or overheating. This in turn may cause
excessive fuel consumption or damage to the
engine. If any of the above symptoms are
encountered, have your vehicle checked at a
GT-R certified NISSAN dealer or other competent service facility.
However, now and then you may notice
light spark knock for a short time while
accelerating or driving up hills. This is no
cause for concern, because you get the
greatest fuel benefit when there is light
spark knock for a short time under heavy
engine load.
9-6
ENGINE OIL AND OIL FILTER RECOMMENDATION
Selecting the correct oil
It is essential to choose the correct grade,
quality, and viscosity engine oil to ensure
satisfactory engine life and performance.
(
“Capacities and recommended fluids/lubricants” page 9-2)
Mobil 1 (0W-40) (100% synthetic) is the factory
fill oil. The VR38 engine with its plasma-sprayed
bores was developed using this oil. NISSAN
cannot ensure proper engine operation and
durability if other 0W-40 synthetic oil is used.
If Mobil 1 (0W-40) is not available, Mobil 1
(10W-40) (100% synthetic) may be used;
however, some performance loss may be
noticed.
NOTICE
Using an engine oil other than that
specified could adversely affect the
engine. See the 2016 NISSAN GT-R
Warranty Information Booklet for details and exclusions.
Oil additives
NISSAN does not recommend the use of oil
additives. The use of an oil additive is not
necessary when the proper oil type is used and
maintenance intervals are followed.
Oil which may contain foreign matter or has
been previously used should not be used.
Oil viscosity
The engine oil viscosity or thickness changes
with temperature. Because of this, it is important
that the engine oil viscosity be selected based
on the temperatures at which the vehicle will be
operated before the next oil change. Choosing
an oil viscosity other than that recommended
could cause serious engine damage.
Selecting the correct oil filter
Your new vehicle is equipped with a high-quality
genuine NISSAN oil filter. NISSAN recommends
to use the genuine NISSAN oil filter for the
reason described in change intervals.
Change intervals
The oil and oil filter change intervals for your
engine are based on the use of the specified
quality oils and filters. Oil and filter other than the
specified quality, or oil and filter change intervals
longer than recommended could reduce engine
Technical and consumer information
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(331,1)
life. Damage to engines caused by improper
maintenance or use of incorrect oil and filter
quality and/or viscosity is not covered by the
NISSAN new vehicle limited warranties.
Your engine was filled with a high quality engine
oil when it was built. You do not have to change
the oil before the first recommended change
interval. Oil and filter change intervals depend
upon how you use your vehicle. Operation under
the following conditions may require more
frequent oil and filter changes.
.
repeated short distance driving at cold
outside temperatures
.
driving in dusty conditions
.
extensive idling
. stop and go “rush hour” traffic
Refer to the “NISSAN Service and Maintenance
Guide” for the maintenance schedule.
AIR CONDITIONING SYSTEM REFRIGERANT AND LUBRICANT RECOMMENDATIONS
NOTICE
The use of any other refrigerant or
lubricant will cause severe damage to
the air conditioning system and will
require the replacement of all air conditioner system components.
The refrigerant HFC-134a (R-134a) in your
NISSAN vehicle will not harm the earth’s ozone
layer. Although this refrigerant does not affect
the earth’s atmosphere, certain governmental
regulations require the recovery and recycling of
any refrigerant during automotive air conditioning system service. Your GT-R certified NISSAN
dealer has the trained technicians and equipment needed to recover and recycle your air
conditioning system refrigerant.
Contact a GT-R certified NISSAN dealer when
servicing your air conditioning system.
The air conditioning system in your
NISSAN vehicle must be charged with the
refrigerant HFC-134a (R-134a) and the
lubricant, NISSAN UV Luminous Oil Type
S or the exact equivalents.
Technical and consumer information 9-7
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(332,1)
SPECIFICATIONS
ENGINE
Model
VR38
Type
Cylinder arrangement
Bore 6 Stroke
Displacement
Firing order
Gasoline, 4-cycle
6-cylinder, V-slanted at 608
3.760 6 3.480 (95.5 6 88.4)
231.83 (3,799)
1-2-3-4-5-6
in (mm)
cu in (cm3)
Idle speed
Ignition timing (B.T.D.C.)
rpm
degree/rpm
No adjustment is necessary.
Spark plug
Standard
DILKAR8A8
Spark plug gap (Normal)
in (mm)
0.031 (0.8)
Timing chain
Camshaft operation
This spark ignition system complies with the Canadian standard ICES-002.
9-8
Technical and consumer information
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(333,1)
WHEELS AND TIRES
Tire
Type
Summer
All-season
Size
Pressure PSI (kPa) [Cold]
Front:
255/40ZRF20 (97Y)
30 (210)
Rear:
285/35ZRF20 (100Y)
29 (200)
Front:
255/40RF20 97W
Rear:
285/35RF20 100W
32 (220)
30 (210)
Make sure to use the tires for GT-R. See the 2016 Warranty Information Booklet for the applicable
exclusions.
Technical and consumer information 9-9
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(334,1)
Road wheel
DIMENSIONS
in (mm)
Type
Aluminum
Size
Front:
Rear:
Offset in (mm)
20 6 9-1/2J*1
20 6 10J*2
20 6 10-1/2J
1.77 (45)*1
1.61 (41)*2
0.98 (25)
*1: Except for NISMO models
*2: NISMO models
Make sure to use the road wheels for GT-R. See the 2016 Warranty Information Booklet for the
applicable exclusions.
Overall length
183.9 (4,670)*1
184.3 (4,680)*2
Overall width
74.6 (1,895)
Overall height
53.9 (1,370)
Front tread
62.6 (1,590)*1
63.0 (1,600)*2
Rear tread
Wheelbase
63.0 (1,600)
109.4 (2,780)
*1: Except for NISMO models
*2: NISMO models
9-10 Technical and consumer information
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(335,1)
WHEN TRAVELING OR
REGISTERING IN ANOTHER
COUNTRY
VEHICLE IDENTIFICATION
If you plan to travel in another country, you
should first find out if the fuel available is suitable
for your vehicle’s engine.
Using fuel with too low an octane rating may
cause engine damage. All gasoline vehicles
must be operated with unleaded gasoline.
Therefore, avoid taking your vehicle to areas
where appropriate fuel is not available.
When transferring the registration of your
vehicle to another country, state, province
or district, it may be necessary to modify the
vehicle to meet local laws and regulations.
The laws and regulations for motor vehicle
emission control and safety standards vary
according to the country, state, province or
district; therefore, vehicle specifications may
differ.
When any vehicle is to be taken into
another country, state, province or district
and registered, its modifications, transportation, and registration are the responsibility of the user. NISSAN is not
responsible for any inconvenience that
may result.
VEHICLE IDENTIFICATION NUMBER
(VIN) PLATE
VEHICLE IDENTIFICATION NUMBER
(chassis number)
The vehicle identification number plate is attached as shown. This number is the identification for your vehicle and is used in the vehicle
registration.
The number is stamped as shown in the engine
compartment.
Technical and consumer information 9-11
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(336,1)
ENGINE SERIAL NUMBER
The number is stamped on the engine as shown.
F.M.V.S.S./C.M.V.S.S. CERTIFICATION LABEL
EMISSION CONTROL INFORMATION LABEL
The Federal/Canadian Motor Vehicle Safety
Standards (F.M.V.S.S./C.M.V.S.S.) certification
label is affixed as shown. This label contains
valuable vehicle information, such as: Gross
Vehicle Weight Ratings (GVWR), Gross Axle
Weight Rating (GAWR), month and year of
manufacture, Vehicle Identification Number
(VIN), etc. Review it carefully.
The emission control information label is attached as shown.
9-12 Technical and consumer information
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(337,1)
INSTALLING FRONT LICENSE PLATE
TIRE AND LOADING INFORMATION
LABEL
AIR CONDITIONER SPECIFICATION
LABEL
The cold tire pressure is shown on the Tire and
Loading Information label affixed to the door end
as illustrated.
The air conditioner specification label is attached as shown.
Make sure that the two POP® nuts as illustrated
are enclosed in the plastic bag. They are used
for front license plate installation.
To install the front license plate to your vehicle,
contact a GT-R certified NISSAN dealer.
Technical and consumer information 9-13
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(338,1)
VEHICLE LOADING INFORMATION
WARNING
.
.
.
It is extremely dangerous to ride
in a cargo area inside the vehicle. In a collision, people riding
in these areas are more likely to
be seriously injured or killed.
Do not allow people to ride in
any area of vehicle that is not
equipped with seats and seat
belts.
Be sure everyone in your vehicle
is in a seat and using a seat belt
properly.
.
.
.
TERMS
It is important to familiarize yourself with the
following terms before loading your vehicle:
. Curb Weight (actual weight of your
vehicle) - vehicle weight including:
standard and optional equipment, fluids
or emergency tools. This weight does
not include passengers and cargo.
. GVW (Gross Vehicle Weight) - curb
.
weight plus the combined weight of
passengers and cargo.
GVWR (Gross Vehicle Weight Rating)
- maximum total combined weight of the
unloaded vehicle, passengers, luggage,
hitch, trailer tongue load and any other
optional equipment. This information is
located on the F.M.V.S.S./C.M.V.S.S.
label.
GAWR (Gross Axle Weight Rating) maximum weight (load) limit specified
for the front or rear axle. This information is located on the F.M.V.S.S./C.M.V.
S.S. label.
GCWR (Gross Combined Weight Rating) - The maximum total weight rating
of the vehicle, passengers, cargo, and
trailer.
Vehicle Capacity Weight, Load limit,
Total load capacity - maximum total
weight limit specified of the load
(passengers and cargo) for the vehicle.
This is the maximum combined weight
of occupants and cargo that can be
loaded into the vehicle. If the vehicle is
.
used to tow a trailer, the trailer tongue
weight must be included as part of the
cargo load. This information is located
on the Tire and Loading Information
label.
Cargo capacity - permissible weight of
cargo, the weight of total occupants
weight subtracted from the load limit.
9-14 Technical and consumer information
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(339,1)
4. The resulting figure equals the available
VEHICLE LOAD CAPACITY
Do not exceed the load limit of your vehicle
shown as “The combined weight of occupants and cargo” on the Tire and Loading
Information label. Do not exceed the
number of occupants shown as “Seating
Capacity” on the Tire and Loading Information label.
To get “the combined weight of occupants
and cargo”, add the weight of all occupants, then add the total luggage weight.
Examples are shown in the illustration.
Steps for determining correct load
limit
1. Locate the statement “The combined
weight of occupants and cargo should
never exceed XXX kg or XXX lbs” on
your vehicle’s placard.
2. Determine the combined weight of the
driver and passengers that will be riding
in your vehicle.
3. Subtract the combined weight of the
driver and passengers from XXX kg or
XXX lbs.
amount of cargo and luggage load
capacity. For example, if the XXX
amount equals 1400 lbs. and there will
be five 150 lb. passengers in your
vehicle, the amount of available cargo
and luggage load capacity is 650 lbs.
(1400 − 750 (5 x 150) = 650 lbs) or
640 − 340 (5 x 70) = 300 kg.)
5. Determine the combined weight of
luggage and cargo being loaded on
the vehicle. That weight may not safely
exceed the available cargo and luggage
load capacity calculated in Step 4.
6. If your vehicle will be towing a trailer,
load from your trailer will be transferred
to your vehicle. Consult this manual to
determine how this reduces the available cargo and luggage load capacity
of your vehicle.
Before driving a loaded vehicle, confirm
that you do not exceed the Gross Vehicle
Weight Rating (GVWR) or the Gross Axle
Weight Rating (GAWR) for your vehicle.
“Measurement of weights” page 9(
16)
Technical and consumer information 9-15
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(340,1)
Also check tires for proper inflation pressures. See the Tire and Loading Information
label.
LOADING TIPS
. The GVW must not exceed GVWR or
GAWR as specified on the F.M.V.S.S./
C.M.V.S.S. certification label.
. Do not load the front and rear axle to
the GAWR. Doing so will exceed the
GVWR.
WARNING
.
.
Properly secure all cargo to help
prevent it from sliding or shifting. Do not place cargo higher
than the seatbacks. In a sudden
stop or collision, unsecured cargo could cause personal injury.
Do not load your vehicle any
heavier than the GVWR or the
maximum front and rear
GAWRs. If you do, parts of your
vehicle can break, tire damage
could occur, or it can change the
way your vehicle handles. This
.
could result in loss of control
and cause personal injury.
Overloading could not only
shorten the life of your vehicle
and the tires, but also could lead
to hazardous vehicle handling
and long braking distance. This
may cause a premature tire
malfunction, which could result
in a serious accident and personal injury. Repairs due to overloading the vehicle are not
covered by the vehicle’s warranty. (See the 2016 NISSAN
GT-R Warranty Information
Booklet.)
(GAWR). The total of the axle loads should
not exceed the gross vehicle weight rating
(GVWR). These ratings are given on the
vehicle certification label. If weight ratings
are exceeded, move or remove items to
bring all weights below the ratings.
MEASUREMENT OF WEIGHTS
Secure loose items to prevent weight shifts
that could affect the balance of your
vehicle. When the vehicle is loaded, drive
to a scale and weigh the front and the rear
wheels separately to determine axle loads.
Individual axle loads should not exceed
either of the gross axle weight ratings
9-16 Technical and consumer information
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(341,1)
TOWING A TRAILER
FLAT TOWING
UNIFORM TIRE QUALITY GRADING
Do not tow a trailer with your vehicle.
Towing your vehicle with all four wheels on the
ground is sometimes called flat towing. This
method is sometimes used when towing a
vehicle behind a recreational vehicle, such as a
motor home.
DOT (Department Of Transportation) Quality
Grades: All passenger car tires must conform to
federal safety requirements in addition to these
grades.
DO NOT tow the GT-R with all four wheels on
the ground (flat towing). Doing so WILL
DAMAGE internal transmission parts. Tow the
GT-R with all four wheels off the ground.
(
“Towing your vehicle” page 6-9)
Quality grades can be found where applicable
on the tire sidewall between tread shoulder and
maximum section width. For example:
Treadwear 200 Traction AA Temperature A
TREADWEAR
The treadwear grade is a comparative rating
based on the wear rate of the tire when tested
under controlled conditions on a specified
government test course. For example, a tire
graded 150 would wear one and one-half (1
1/2) times as well on the government course as
a tire graded 100. The relative performance of
tires depends upon actual conditions of their
use, however, and may depart significantly from
the norm due to variations in driving habits,
service practices and differences in road characteristics and climate.
Technical and consumer information 9-17
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(342,1)
EMISSION CONTROL SYSTEM
WARRANTY
TRACTION AA, A, B AND C
The traction grades, from highest to lowest, are
AA, A, B and C. Those grades represent the
tire’s ability to stop on wet pavement as
measured under controlled conditions on specified government test surfaces of asphalt and
concrete. A tire marked C may have poor
traction performance.
WARNING
The traction grade assigned to this tire
is based on straight-ahead braking
traction tests, and does not include
acceleration, cornering, hydroplaning,
or peak traction characteristics.
TEMPERATURE A, B AND C
The temperature grades A (the highest), B, and
C, representing the tire’s resistance to the
generation of heat and its ability to dissipate
heat when tested under controlled conditions on
a specified indoor laboratory test wheel. Sustained high temperature can cause the material
of the tire to degenerate and reduce tire life, and
excessive temperature can lead to sudden tire
failure. The grade C corresponds to a level of
performance which all passenger car tires must
meet under the Federal Motor Vehicle Safety
Standard No. 109. Grades B and A represent
higher levels of performance on the laboratory
test wheel than the minimum required by law.
WARNING
The temperature grade for this tire is
established for a tire that is properly
inflated and not overloaded. Excessive
speed, under-inflation, or excessive
loading, either separately or in combination, can cause heat build-up and
possible tire failure.
Your NISSAN is covered by specific emission
warranties:
For the United States, see the 2016 NISSAN
GT-R Warranty Information Booklet.
For Canada, see the Warranty and Roadside
Assistance Information Booklet.
If you did not receive a Warranty Information
Booklet (Warranty and Roadside Assistance
Information (Canada only)), or it has become
lost, you may obtain a replacement by writing to:
.
NISSAN Division
NISSAN North America, Inc.
Consumer Affairs Department
P.O. Box 685003
Franklin, TN 37068-5003
.
NISSAN Canada Inc.
5290 Orbitor Drive
Mississauga, Ontario,
L4W 4Z5
9-18 Technical and consumer information
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(343,1)
REPORTING SAFETY DEFECTS
For USA
If you believe that your vehicle has a defect
which could cause a crash or could cause
injury or death, you should immediately
inform the National Highway Traffic Safety
Administration (NHTSA) in addition to
notifying NISSAN.
If NHTSA receives similar complaints, it
may open an investigation, and if it finds
that a safety defect exists in a group of
vehicles, it may order a recall and remedy
campaign. However, NHTSA cannot become involved in individual problems between you, your dealer, or NISSAN.
To contact NHTSA, you may call the
Vehicle Safety Hotline toll-free at 1-888327-4236 (TTY: 1-800-424-9153); go to
http://www.safercar.gov; or write to: Administrator, NHTSA, 400 Seventh Street,
SW., Washington, D.C. 20590. You can
also obtain other information about motor
vehicle safety from http://www.safercar.
gov.
You may notify NISSAN by contacting our
Consumer Affairs Department, toll-free, at
1-866-668-1GTR (1-866-668-1487).
For Canada
If you believe that your vehicle has a defect
which could cause a crash or could cause
injury or death, you should immediately
inform Transport Canada in addition to
notifying NISSAN.
www.tc.gc.ca/roadsafety (English speakers) or www.tc.gc.ca/securiteroutiere
(French speakers).
To notify NISSAN of any safety concerns
please contact our Consumer Information
Centre toll free at 1-800-387-0122.
If Transport Canada receives complaints, it
may open an investigation, and if it finds
that a safety defect exists in a group of
vehicles, it may request that NISSAN
conduct a recall campaign. However,
Transport Canada cannot become involved
in individual problems between you, your
dealer, or NISSAN.
You may contact Transport Canada’s Defect Investigations and Recalls Division toll
free at 1-800-333-0510. You may also
report safety defects online at: https://
wwwapps.tc.gc.ca/Saf-Sec-Sur/7/
PCDB-BDPP/Index.aspx.
Additional information concerning motor
vehicle safety may be obtained from Transport Canada’s Road Safety Information
Centre at 1-800-333-0371 or online at
Technical and consumer information 9-19
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(344,1)
READINESS FOR INSPECTION/
MAINTENANCE (I/M) TEST (US only)
A vehicle equipped with All-Wheel Drive (AWD)
should never be tested using a two wheel
dynamometer (such as the dynamometers used
by some states for emissions testing), or similar
equipment. Make sure you inform test facility
personnel that your vehicle is equipped with
AWD before it is placed on a dynamometer.
Using the wrong test equipment may result in
transmission damage or unexpected vehicle
movement which could result in serious vehicle
damage or personal injury.
Due to legal requirements in some states/ areas,
your vehicle may be required to be in what is
called the “ready condition” for an Inspection/
Maintenance (I/M) test of the emission control
system.
The vehicle is set to the “ready condition” when
it is driven through certain driving patterns.
Usually, the “ready condition” can be obtained
by ordinary usage of the vehicle.
If a powertrain system component is repaired or
the battery is disconnected, the vehicle may be
reset to a “not ready condition”. Before taking
the I/M test, check the vehicle’s inspection/
maintenance test readiness condition. Push the
ignition switch to the ON position without
starting the engine. If the Malfunction Indicator
Light (MIL) comes on steady for 20 seconds and
then blinks for 10 seconds, the I/M test
EVENT DATA RECORDERS (EDR)
condition is “not ready”. If the MIL does not
blink after 20 seconds, the I/M test condition is
“ready”.
Contact a GT-R certified NISSAN dealer to set
“ready condition” or to prepare the vehicle for
testing.
This vehicle is equipped with an Event Data
Recorder (EDR). The main purpose of an EDR is
to record, in certain crash or near crash-like
situations, such as an air bag deployment or
hitting a road obstacle, data that will assist in
understanding how a vehicle’s systems performed. The EDR is designed to record data
related to vehicle dynamics and safety systems
for a short period of time, typically 30 seconds
or less. The EDR in this vehicle is designed to
record such data as:
.
How various systems in your vehicle were
operating;
.
Whether or not the driver and passenger
safety belts were buckled/fastened;
.
How far (if at all) the driver was depressing
the accelerator and/or brake pedal; and,
.
How fast the vehicle was traveling.
. Sounds are not recorded.
These data can help provide a better understanding of the circumstances in which crashes
and injuries occur. NOTE: EDR data are
recorded by your vehicle only if a nontrivial
crash situation occurs; no data are recorded by
the EDR under normal driving conditions and no
personal data (e.g. name, gender, age and crash
location) are recorded. However, other parties,
such as law enforcement, could combine the
9-20 Technical and consumer information
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(345,1)
VEHICLE STATUS DATA RECORDER
(VSDR)
EDR data with the type of personally identifying
data routinely acquired during a crash investigation.
To read data recorded by an EDR, special
equipment is required and access to the vehicle
or the EDR is needed. In addition to the vehicle
manufacturer and NISSAN dealer, other parties,
such as law enforcement, that have the special
equipment, can read the information if they have
access to the vehicle or the EDR. EDR data will
only be accessed with the consent of the vehicle
owner or lessee or as otherwise required or
permitted by law.
The Vehicle Status Data Recorder (VSDR) is
different from the Event Data Recorder described in “Event Data Recorder” in this section.
The VSDR is not a crash-activated device, but it
records and accumulates vehicle data while
driving.
Examples are:
.
Vehicle operating information such as the
wheel speeds of the front and rear wheels
.
Engine control information such as the
engine speed and boost pressure
The VSDR always records and stores vehicle
operating data between periodic inspections,
which can assist and be used for servicing,
diagnosing and performing warranty repairs.
neither NISSAN nor third parties affiliated with
NISSAN, shall disclose or offer the acquired
data to other non-affiliated third parties.
.
With the agreement of the vehicle owner
.
When legally required to, such as when
ordered by a court of law, etc.
.
When offering processed data so that
neither the vehicle owner nor the vehicle is
identified, to research centers for statistical
analysis, etc.
The VSDR does not record sounds, conversations or images.
To read data recorded by the VSDR, special
equipment is required and access to the vehicle
or the VSDR is needed.
HANDLING OF DATA
NISSAN and third parties affiliated with NISSAN
can acquire and use the data recorded by the
VSDR in order to confirm the part replacement
history to improve the quality of NISSAN
vehicles.
With the exception of the following cases,
Technical and consumer information 9-21
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(346,1)
OWNER’S MANUAL/SERVICE
MANUAL ORDER INFORMATION
Genuine NISSAN Service Manuals for this
model year and prior can be purchased. A
genuine NISSAN Service Manual is the best
source of service and repair information for your
vehicle. This manual is the same one used by the
factory-trained technicians working at NISSAN
dealerships. Genuine NISSAN Owner’s Manuals can also be purchased.
For USA:
For current pricing and availability of genuine
NISSAN Service Manuals,
www.nissan-techinfo.com
For current pricing and availability of genuine
NISSAN Owner’s Manuals, contact:
1-800-247-5321
For Canada:
To purchase a copy of a genuine NISSAN
Service Manual or Owner’s Manual for this
model year and prior, please contact a GT-R
certified NISSAN dealer. For the phone number
and location of a GT-R certified NISSAN dealer
in your area call the NISSAN Information Center
at 1-800-387-0122 and a bilingual NISSAN
representative will assist you.
9-22 Technical and consumer information
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(347,1)
MEMO
Technical and consumer information 9-23
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(348,1)
MEMO
9-24 Technical and consumer information
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(349,1)
10 Index
A
Active noise control ................................................... 5-54
Additional maintenance items ........................... GTR-12
Air cleaner .................................................................... 8-21
Air conditioner
Air conditioner specification label ................... 9-13
Air conditioning system refrigerant and
lubricant recommendations ........................................ 9-7
Air fresheners ................................................................ 7-7
All-season tires ..................................................... GTR-11
All-Wheel Drive ........................................................... 5-41
All-Wheel Drive driving safety precautions............ 5-9
Anti-freeze .................................................................... 5-52
Anti-lock Braking System ......................................... 5-49
Anti-lock Braking System warning ......................... 2-37
Audible reminders ...................................................... 2-32
Automatic
Automatic door lock system ................................ 3-5
Average fuel consumption and speed .................. 2-16
Avoiding body damage ....................................... GTR-11
Avoiding collision and rollover .................................. 5-7
AWD clutch high temperature warning ................ 2-38
AWD system characteristics ................................... 5-44
AWD system warning................................................ 2-39
AWD warning light..................................................... 5-41
Intelligent Key battery replacement................. 8-27
Before starting the engine ....................................... 5-13
Body repair............................................................. GTR-12
Booster seats .............................................................. 1-30
Brake
Brake assist .......................................................... 5-49
Brake fluid .............................................. GTR-4, 8-15
Brake pad wear warning ................................... 8-23
Brake system ........................................................ 5-48
Brakes .................................................................... 8-23
High performance brake system ..................... 8-24
Low brake fluid warning .................................... 2-37
Parking brake........................................................ 5-33
Parking brake break-in ....................................... 5-48
Parking brake release warning ......................... 2-36
Replacing the brake pads ................................. 8-24
Self-adjusting brakes .......................................... 8-23
Brake dust .............................................................. GTR-26
Brake pad ............................................................... GTR-15
Brake pad and disc rotor ..................................... GTR-5
Brake pad break-in procedure .......................... GTR-15
Brake system information ................................... GTR-26
Brakes ................................................... GTR-18, GTR-22
Braking precautions ................................................... 5-48
Break-in schedule........................................ GTR-9, 5-39
C
B
Battery ............................................................... 5-52, 8-17
Intelligent Key battery discharge ..................... 5-12
Intelligent Key battery discharge indicator .... 2-45
Capacities and recommended fluids/lubricants ... 9-2
Changing
Changing engine coolant .................................. 8-12
Changing engine oil and filter .......................... 8-14
Changing wheels and tires ............................... 8-41
Checking
Checking bulbs .................................................... 2-25
Checking engine coolant level ......................... 8-11
Checking engine oil level .................................. 8-13
Checking the tire pressure ............................... 8-36
Child restraints ............................................................ 1-15
Child safety .................................................................. 1-13
Chrome parts................................................................. 7-5
Cleaning ........................................................................ 8-22
Cleaning exterior ........................................................... 7-2
Cleaning interior............................................................ 7-7
Closing the fuel-filler door ....................................... 3-24
Closing the hood ........................................................ 3-18
Coat hooks................................................................... 2-59
Cockpit ............................................................................ 2-3
Cold weather driving ................................................. 5-52
Console box ................................................................. 2-59
Cool down.............................................................. GTR-13
Coolant
Changing engine coolant .................................. 8-12
Checking engine coolant level ......................... 8-11
Draining of coolant water .................................. 5-52
Engine coolant temperature gauge ................... 2-7
Coolant level and mixture ratio ......................... GTR-15
Corrosion protection.................................................... 7-9
Cracks on brake pad ........................................... GTR-26
Cracks on the disc rotors .................................. GTR-26
Cruise control .................................................. 2-16, 5-34
Cruise control operations ......................................... 5-36
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(350,1)
Cruise control system warning ............................... 2-40
Cup holders ................................................................. 2-56
Current fuel consumption ......................................... 2-15
D
Differential oil ........................................................... GTR-4
Dimensions................................................................... 9-10
Distance to empty ...................................................... 2-17
Door pocket ................................................................. 2-58
Door/trunk open warning.......................................... 2-41
Doors ............................................................................... 3-4
Draining of coolant water ......................................... 5-52
Drinking alcohol/drugs and driving .......................... 5-9
Drive belts .................................................................... 8-19
Drive computer............................................................ 2-15
Driving
All-Wheel Drive driving safety precautions...... 5-9
Cold weather driving .......................................... 5-52
Drinking alcohol/drugs and driving .................... 5-9
Driving on snow or ice ....................................... 5-53
Driving the vehicle ............................................... 5-15
Driving tips ............................................................ 5-21
Precautions when starting and driving ............. 5-3
Driving after replacing tires ................................ GTR-12
Dry carbon fiber parts ................ GTR-7, GTR-27, 7-6
Dual clutch transmission ........................ GTR-27, 5-15
E
Elapsed time and trip odometer ............................. 2-17
Emergency engine shut off ............................. 5-11, 6-3
Emergency trunk lid release .................................... 3-21
Emission control information label ......................... 9-12
Emission control system warranty .......................... 9-18
Engine ............................................................................. 9-8
Before starting the engine ................................ 5-13
Changing engine coolant .................................. 8-12
Changing engine oil and filter .......................... 8-14
Checking engine coolant level ......................... 8-11
Checking engine oil level .................................. 8-13
Emergency engine shut off ...................... 5-11, 6-3
Engine block heater ............................................ 5-54
Engine compartment........................................... 8-25
Engine compartment check locations ............... 8-8
Engine coolant temperature gauge ................... 2-7
Engine cooling system ....................................... 8-10
Engine oil ................................................ GTR-3, 8-13
Engine oil and oil filter recommendation .......... 9-6
Engine oil level display ....................................... 2-12
Engine oil low pressure warning ..................... 2-34
Engine serial number .......................................... 9-12
Engine start operation indicator ...................... 2-43
Engine system warning ...................................... 2-34
Operating range for engine start..................... 5-10
Starting the engine ............................................. 5-13
Engine and powertrain ...................... GTR-15, GTR-22
Engine oil maintenance ......................................... GTR-4
Engine output ........................................................ GTR-23
Engine output according to the
coolant temperature ............................................. GTR-23
Engine speed is restricted ................................. GTR-23
Environmental factors influence the rate
of corrosion .................................................................... 7-9
Event Data Recorders (EDR) .................................. 9-20
Exhaust gas.................................................................... 5-3
Exhaust muffler and trunk carpet........................ GTR-6
Explanation of maintenance items ............................ 8-4
Extended storage fuse switch ................................. 8-26
Exterior and interior lights ........................................ 8-30
F
F.M.V.S.S./C.M.V.S.S. certification label............... 9-12
Features of each mode ............................................. 5-27
Flat tire ............................................................................ 6-3
Flat towing.................................................................... 9-17
Floor mats....................................................................... 7-8
Fluid
Brake fluid .............................................. GTR-4, 8-15
Fluid level check .................................................. 8-18
Low brake fluid warning .................................... 2-37
Low washer fluid warning ................................. 2-42
Power steering fluid ............................................ 8-14
Window washer fluid.......................................... 8-16
Fluids ..................................................... GTR-14, GTR-18
Forward-facing child restraint installation
using LATCH ............................................................... 1-24
Forward-facing child restraint installation using
the seat belts ............................................................... 1-26
Freeing a frozen door lock ....................................... 5-52
10-2
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(351,1)
Front seat-mounted side-impact supplemental
air bag and roof-mounted curtain side-impact
supplemental air bag systems................................. 1-45
Front seats ..................................................................... 1-3
Front/rear tire size discrepancy warning .............. 2-38
Fuel .......................................................................... GTR-12
Average fuel consumption and speed ........... 2-16
Capacities and
recommended fluids/lubricants ........................... 9-2
Closing the fuel-filler door ................................ 3-24
Current fuel consumption .................................. 2-15
Fuel gauge ............................................................... 2-8
Fuel information....................................................... 9-4
Fuel-filler door ...................................................... 3-23
Increasing fuel economy .................................... 5-41
Low fuel warning ................................................. 2-40
Opening the fuel-filler door............................... 3-24
Fuel Efficient Driving Tips ........................................ 5-40
Fuses ............................................................................. 8-25
G
Garage door opener
HomeLink® Universal Transceiver ................... 2-64
Gasoline smell ....................................................... GTR-23
Gauge
Engine coolant temperature gauge ................... 2-7
Fuel gauge ............................................................... 2-8
Meters and gauges ................................................ 2-5
General maintenance ......................................... 8-3, 8-4
Glass ............................................................................... 7-5
Glove box ..................................................................... 2-58
GT-R performance optimization services ......... GTR-8
GT-R special precautions..................................... GTR-5
GT-R special specification parts ........................ GTR-3
GT-R specific information..................................... GTR-3
GT-R specific vehicle characteristics .............. GTR-23
H
Handling of data ......................................................... 9-21
Hazard warning flasher switch .................................. 6-2
Head restraints/headrests .......................................... 1-5
Headlight
Headlight and turn signal switch..................... 2-50
Headlight switch .................................................. 2-50
Headlights ............................................................. 8-30
Heated seats ............................................................... 2-54
High altitude .......................................................... GTR-23
High performance brake system ............................ 8-24
Hill Start Assist System ............................................ 5-38
HomeLink® Universal Transceiver .......................... 2-64
Hood .............................................................................. 3-17
Horn ............................................................................... 2-54
How to switch the modes ........................................ 5-25
How to use R mode start function ........................ 5-33
I
Idle speed is not steady ..................................... GTR-23
If your vehicle overheats ............................................. 6-8
Ignition switch operation .......................................... 5-10
Ignition switch positions ........................................... 5-11
Increasing fuel economy ........................................... 5-41
Indicator lights ............................................................. 2-31
Indicators and display................................................ 5-36
Infants ............................................................................ 1-14
Injured persons ............................................................. 1-9
Inside mirror ................................................................. 3-26
Inspection and adjustments after driving ....... GTR-18
Inspection and adjustments before driving .... GTR-14
Installing front license plate ..................................... 9-13
Installing top tether strap ............................. 1-26, 1-30
Instrument brightness control.................................. 2-11
Instrument panel ........................................................... 2-4
Intelligent Key ................................................................ 3-2
Intelligent Key battery discharge ............................ 5-12
Intelligent Key battery discharge indicator ........... 2-45
Intelligent Key battery replacement........................ 8-27
Intelligent Key functions .............................................. 3-9
Intelligent Key insertion indicator............................ 2-44
Intelligent Key removal indicator ............................. 2-45
Intelligent Key system .................................................. 3-8
Interior light control switch ...................................... 2-63
Interior lights ................................................................ 2-62
J
Jacking vehicle and removing wheels ................... 8-43
Jump starting ...................................................... 6-5, 8-19
K
Key
Intelligent Key .......................................................... 3-2
10-3
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(352,1)
Intelligent Key battery discharge ..................... 5-12
Intelligent Key battery discharge indicator .... 2-45
Intelligent Key battery replacement................. 8-27
Intelligent Key functions ........................................ 3-9
Intelligent Key insertion indicator..................... 2-44
Intelligent Key removal indicator ...................... 2-45
Intelligent Key system ............................................ 3-8
Keys ........................................................................... 3-2
Locking with mechanical key............................... 3-6
No key warning .................................................... 2-42
Remote keyless entry system ........................... 3-12
L
Larger children ............................................................
Light
AWD warning light..............................................
Exterior and interior lights .................................
Headlight and turn signal switch.....................
Headlight switch ..................................................
Headlights .............................................................
Indicator lights ......................................................
Interior light control switch ...............................
Interior lights .........................................................
Lights ......................................................................
Map lights ..............................................................
Supplemental air bag warning light ................
Vanity mirror lights ...............................................
Warning lights ......................................................
Warning lights, indicator lights and
audible reminders ................................................
1-14
5-41
8-30
2-50
2-50
8-30
2-31
2-63
2-62
8-29
2-62
1-47
2-64
2-25
2-25
Limited Slip Differential ............................................. 5-45
Loading tips ................................................................. 9-16
Lock
Anti-lock Braking System .................................. 5-49
Anti-lock Braking System warning .................. 2-37
Automatic door lock system ................................ 3-5
Freeing a frozen door lock ................................ 5-52
Locking with inside lock knob ............................. 3-5
Locking with mechanical key............................... 3-6
Locking with power door lock switch ............... 3-5
Steering lock release
malfunction indicator........................................... 2-44
Wheel lock nuts ................................................... 8-49
Low brake fluid warning ........................................... 2-37
Low fuel warning ........................................................ 2-40
Low tire pressure warning ....................................... 2-39
Low washer fluid warning ........................................ 2-42
Lower anchors and tethers for
children system ........................................................... 1-17
M
Maintenance
Explanation of maintenance items ...................... 8-4
General maintenance ................................... 8-3, 8-4
Maintenance information................................. GTR-3
Maintenance precautions ..................................... 8-6
Maintenance requirements ................................... 8-3
Readiness for
Inspection/Maintenance test............................. 9-20
Scheduled maintenance ....................................... 8-3
Seat belt maintenance ....................................... 1-13
Map lights ..................................................................... 2-62
Matte paint care............................................................ 7-2
Measurement of weights .......................................... 9-16
Meters and gauges ...................................................... 2-5
Mirror
Inside mirror .......................................................... 3-26
Mirrors .................................................................... 3-26
Outside mirrors .................................................... 3-27
Vanity mirror .......................................................... 3-28
Vanity mirror lights ............................................... 2-64
Most common factors contributing to
vehicle corrosion ........................................................... 7-9
Multi Function Display Owner’s Manual ................. 4-2
N
NISSAN Advanced Air Bag System ..................... 1-40
NISSAN Vehicle Immobilizer System .................... 2-47
No key warning ........................................................... 2-42
Noises are heard while driving ......................... GTR-24
O
Odometer/twin trip odometer.................................... 2-6
Off-road recovery ......................................................... 5-7
Oil
Changing engine oil and filter .......................... 8-14
Checking engine oil level .................................. 8-13
Differential oil ..................................................... GTR-4
Engine oil ................................................ GTR-3, 8-13
Engine oil and oil filter recommendation .......... 9-6
10-4
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(353,1)
Engine oil level display ....................................... 2-12
Engine oil low pressure warning ..................... 2-34
Transmission oil..................................... GTR-4, 8-14
Transmission oil high temperature warning.... 2-36
Opening and closing the trunk ............................... 3-21
Opening the doors ....................................................... 3-7
Opening the fuel-filler door...................................... 3-24
Opening the hood ...................................................... 3-17
Operating range for engine start............................ 5-10
Operation displays ..................................................... 2-43
Outside air temperature ............................................ 2-18
Outside door handles.................................................. 7-6
Outside mirrors ........................................................... 3-27
Outside temperature display indicates
higher temperature ............................................... GTR-23
Overheat
If your vehicle overheats ....................................... 6-8
Owner’s Manual/Service Manual
order information......................................................... 9-22
Power steering ..................................................... 5-47
Power steering fluid ............................................ 8-14
Power windows.................................................... 2-60
Trunk release power cancel switch ................ 3-20
Precautions .................................................................. 8-17
All-Wheel Drive driving safety precautions...... 5-9
Braking precautions ............................................ 5-48
Maintenance precautions ..................................... 8-6
Precautions on child restraints ........................ 1-15
Precautions on cruise control .......................... 5-35
Precautions on seat belt usage .......................... 1-6
Precautions on supplemental
restraint system .................................................... 1-34
Precautions when starting and driving ............. 5-3
Precautions before driving ................................. GTR-10
Precautions on performance driving................ GTR-13
Pregnant women........................................................... 1-9
Push starting.................................................................. 6-7
“PUSH” warning ......................................................... 2-44
Push-button ignition switch ..................................... 5-10
P
Parking
Parking brake........................................................ 5-33
Parking brake break-in ....................................... 5-48
Parking brake release warning ......................... 2-36
Parking/parking on hills...................................... 5-46
Passenger compartment ........................................... 8-26
Power
Locking with power door lock switch ............... 3-5
Power outlets........................................................ 2-55
R
R mode start function................................................ 5-32
Rapid air pressure loss ............................................... 5-8
Readiness for Inspection/Maintenance test ........ 9-20
Rear window defroster switch ................................ 2-50
Rear-facing child restraint installation
using LATCH ............................................................... 1-19
Rear-facing child restraint installation using the
seat belts ...................................................................... 1-21
Recommended fluids and
maintenance interval ............................................ GTR-19
Reducing tight corner braking phenomenon ....... 5-43
Refueling precautions.......................................... GTR-13
Remote keyless entry system .................................. 3-12
Removing spots ............................................................ 7-4
Removing the cowl top cover ................................... 8-9
Repair and replacement procedure ....................... 1-48
Replacement of brake pads and disc rotors.... GTR-5
Replacing spark plugs .............................................. 8-20
Replacing the brake pads ........................................ 8-24
Replacing the wiper blades ..................................... 8-23
Reporting safety defects ......................................... 9-19
Reverse warning ......................................................... 2-35
Roadside assistance program................................... 6-2
Run-flat tire warning .................................................. 2-39
Run-flat tires .................................................................. 6-4
S
Safety
All-Wheel Drive driving safety precautions...... 5-9
Child safety ........................................................... 1-13
Reporting safety defects .................................. 9-19
Safety — Seats, seat belts and supplemental
restraint system ............................................................. 1-1
Scheduled maintenance ............................................. 8-3
Seat
Booster seats ....................................................... 1-30
Forward-facing child restraint installation
using the seat belts ............................................ 1-26
10-5
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(354,1)
Front seat-mounted side-impact supplemental
air bag and roof-mounted curtain side-impact
supplemental air bag systems.......................... 1-45
Front seats ............................................................... 1-3
Heated seats ........................................................ 2-54
NISSAN Advanced Air Bag System .............. 1-40
Precautions on seat belt usage .......................... 1-6
Rear-facing child restraint installation using
the seat belts ........................................................ 1-21
Seat belt extenders ............................................. 1-12
Seat belt maintenance ....................................... 1-13
Seat belts ........................................................ 1-6, 7-8
Seat belts with pretensioners .......................... 1-46
Seats.......................................................................... 1-2
Three-point type seat belt with retractor.......... 1-9
Seat belt
Forward-facing child restraint installation
using the seat belts ............................................ 1-26
Precautions on seat belt usage .......................... 1-6
Rear-facing child restraint installation using
the seat belts ........................................................ 1-21
Seat belt extenders ............................................. 1-12
Seat belt maintenance ....................................... 1-13
Seat belts ........................................................ 1-6, 7-8
Seat belts with pretensioners .......................... 1-46
Three-point type seat belt with retractor.......... 1-9
Security systems......................................................... 2-45
Self-adjusting brakes ................................................. 8-23
Setting (drive computer) .......................................... 2-19
Setting hazard indicator and horn mode .............. 3-13
Shift lever position warning ..................................... 2-35
Shift “P” warning ........................................................ 2-43
Small children .............................................................. 1-14
Spark plugs .................................................................. 8-20
Special winter equipment......................................... 5-53
Specifications ................................................................ 9-8
Speedometer ................................................................. 2-6
Starting
Before starting the engine ................................ 5-13
Jump starting ............................................... 6-5, 8-19
Precautions when starting and driving ............. 5-3
Push starting............................................................ 6-7
Starting the engine ............................................. 5-13
Steering
Power steering ..................................................... 5-47
Power steering fluid ............................................ 8-14
Steering lock release
malfunction indicator........................................... 2-44
Steering wheel ..................................................... 3-25
Steering-wheel-mounted controls ................... 5-35
Tilt/telescopic steering column ........................ 3-25
Storage ......................................................................... 2-56
Summer tires ......................................................... GTR-11
Sun visors..................................................................... 3-26
Sunglasses holder...................................................... 2-57
Supplemental air bag warning labels .................... 1-47
Supplemental air bag warning light ....................... 1-47
Supplemental restraint system ................................ 1-34
Suspension and wheel alignment.... GTR-16, GTR-22
Switch
Hazard warning flasher switch ............................ 6-2
Headlight and turn signal switch..................... 2-50
Headlight switch .................................................. 2-50
How to switch the modes ................................. 5-25
Ignition switch operation ................................... 5-10
Ignition switch positions .................................... 5-11
Interior light control switch ............................... 2-63
Locking with power door lock switch ............... 3-5
Push-button ignition switch .............................. 5-10
Rear window defroster switch ......................... 2-50
Trunk lid release switch ..................................... 3-19
Trunk open request switch................................ 3-19
Trunk release power cancel switch ................ 3-20
VDC, transmission and suspension
setup switches ..................................................... 5-25
Wiper and washer switch ................................. 2-48
T
Tachometer..................................................................... 2-7
Temperature A, B and C .......................................... 9-18
Terms ............................................................................. 9-14
Three-point type seat belt with retractor................ 1-9
Three-way catalyst ....................................................... 5-3
Tight corner braking phenomenon ......................... 5-43
Tilt/telescopic steering column ............................... 3-25
Tire
Changing wheels and tires ............................... 8-41
Checking the tire pressure ............................... 8-36
Flat tire ...................................................................... 6-3
Front/rear tire size discrepancy warning ....... 2-38
Low tire pressure warning ................................ 2-39
Run-flat tire warning ........................................... 2-39
10-6
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(355,1)
Run-flat tires ............................................................ 6-4
Tire and loading information label ........ 8-35, 9-13
Tire chains ............................................................. 8-40
Tire dressing ............................................................ 7-6
Tire equipment ..................................................... 5-53
Tire labeling........................................................... 8-37
Tire pressure ......................................................... 8-32
Tire Pressure Monitoring System .............. 5-4, 6-3
Tire Pressure Monitoring System warning .... 2-40
Tires ........................................................................ 5-44
Types of tires ........................................................ 8-38
Uniform tire quality grading............................... 9-17
Wheels and tires ........................................ 8-32, 9-9
Tires and road wheels........................................... GTR-5
Titanium muffler ....................................................... GTR-6
Change of surface color of
titanium muffler ............................................... GTR-26
Sound heard around titanium muffler ....... GTR-27
To protect your vehicle from corrosion ................. 7-10
Towing
Flat towing............................................................. 9-17
Towing a trailer..................................................... 9-17
Towing recommended by NISSAN .................... 6-9
Towing your vehicle ............................................... 6-9
Traction AA, A, B and C .......................................... 9-18
Transceiver
HomeLink® Universal Transceiver ................... 2-64
Transmission
Dual clutch transmission ................................... 5-15
Transmission clutch high
temperature warning ........................................... 2-36
Transmission oil..................................... GTR-4, 8-14
Transmission oil high temperature warning.... 2-36
Transmission position indicator ........................... 2-9
Transmission system check display ................ 2-14
Transmission system warning ........................... 2-35
VDC, transmission and suspension
setup switches ..................................................... 5-25
Transmission operation characteristics ........... GTR-28
Transmission settings ............................................ GTR-9
Treadwear ..................................................................... 9-17
Troubleshooting guide ............................................... 3-16
Trunk .............................................................................. 3-19
Trunk lid release switch ............................................ 3-19
Trunk open request switch....................................... 3-19
Trunk release power cancel switch ....................... 3-20
Turbocharger system ................................................. 5-31
Turning off the heaters .............................................. 2-54
Turning on the heaters .............................................. 2-54
Types of tires ............................................................... 8-38
U
Underbody ...................................................................... 7-5
Uneven wear of tires ........................................... GTR-24
Uniform tire quality grading...................................... 9-17
Upshift indicator............................................................ 2-9
Using the washer ....................................................... 2-49
Using the wipers......................................................... 2-49
V
Vanity mirror ................................................................. 3-28
Vanity mirror lights ...................................................... 2-64
VDC, transmission and suspension
setup switches ............................................................ 5-25
Vehicle Dynamic Control (VDC)
OFF mode .............................................................. GTR-10
Vehicle Dynamic Control (VDC) warning light .... 2-31
Vehicle Dynamic Control system ............................ 5-50
Vehicle Dynamic Control system warning............ 2-37
Vehicle identification .................................................. 9-11
Vehicle identification number............................ 9-11
Vehicle Identification Number plate ................ 9-11
Vehicle information display....................................... 2-12
Vehicle load capacity................................................. 9-15
Vehicle loading information ...................................... 9-14
Vehicle recovery .......................................................... 6-10
Vehicle security system............................................. 2-45
Vehicle speed .............................................................. 2-16
Vehicle status data recorder.................................... 9-21
W
Warning
Anti-lock Braking System warning ..................
AWD clutch high temperature warning .........
AWD system warning.........................................
AWD warning light..............................................
Brake pad wear warning ...................................
Cruise control system warning ........................
Door/trunk open warning...................................
2-37
2-38
2-39
5-41
8-23
2-40
2-41
10-7
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(356,1)
Engine oil low pressure warning ..................... 2-34
Engine system warning ...................................... 2-34
Front/rear tire size discrepancy warning ....... 2-38
Hazard warning flasher switch ............................ 6-2
Low brake fluid warning .................................... 2-37
Low fuel warning ................................................. 2-40
Low tire pressure warning ................................ 2-39
Low washer fluid warning ................................. 2-42
No key warning .................................................... 2-42
Parking brake release warning ......................... 2-36
“PUSH” warning .................................................. 2-44
Reverse warning .................................................. 2-35
Run-flat tire warning ........................................... 2-39
Shift lever position warning .............................. 2-35
Shift “P” warning ................................................. 2-43
Supplemental air bag warning labels ............. 1-47
Supplemental air bag warning light ................ 1-47
Tire Pressure Monitoring System warning .... 2-40
Transmission clutch high
temperature warning ........................................... 2-36
Transmission oil high temperature warning.... 2-36
Transmission system warning ........................... 2-35
Vehicle Dynamic Control system warning..... 2-37
Warning (drive computer) ................................. 2-23
Warning display ................................................... 2-33
Warning lights ...................................................... 2-25
Warning lights, indicator lights and
audible reminders ................................................ 2-25
Warning signals ................................................... 3-15
Warranty information.............................................. GTR-3
Washing .......................................................................... 7-3
Waxing ............................................................................ 7-4
Wheel alignment ....................................... GTR-10, 5-39
Wheel alignment inspection and adjustment
(if necessary) (including tire
pressure adjustment) ............................................. GTR-8
Wheel lock nuts .......................................................... 8-49
Wheels ............................................................................ 7-5
Wheels and tires ........... GTR-16, GTR-22, 8-32, 9-9
When traveling or registering in
another country ........................................................... 9-11
Where to go for service ............................................. 8-3
Window washer fluid................................................. 8-16
Windows....................................................................... 2-60
Windshield wiper blades .......................................... 8-22
Wiper
Replacing the wiper blades .............................. 8-23
Using the wipers.................................................. 2-49
Windshield wiper blades ................................... 8-22
Wiper and washer switch ................................. 2-48
Wiper and washer switch ........................................ 2-48
10-8
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(357,1)
MEMO
10-9
[ Edit: 2014/ 12/ 8
Model: R35-D ]
(361,1)
GAS STATION INFORMATION
specifically designed for E-15 or E85 fuel can adversely affect the
emission control devices and systems of the vehicle. Damage caused
by such fuel is not covered by the
NISSAN new vehicle limited warranty.
FUEL INFORMATION
VR38 engine
Use unleaded premium gasoline with an octane
rating of at least 93 AKI (Anti-Knock Index)
number (Research octane number 98) to maximize vehicle performance.
If the premium gasoline specified above is not
available, you may use unleaded premium gasoline with an octane rating of at least 91 AKI
number (Research octane number 96), but you
may notice a decrease in performance.
Do not use gasoline with a lower octane rating
than 91 AKI (Research octane number 96).
NOTICE
.
.
.
Using a fuel other than that specified could adversely affect the emission control systems, and may also
affect warranty coverage.
Under no circumstances should a
leaded gasoline be used, since this
will damage the three way catalyst.
Do not use E-15 or E-85 fuel in your
vehicle. Your vehicle is not designed
to run on E-15 or E-85 fuel. Using E15 or E-85 fuel in a vehicle not
.
.
U.S. government regulations require
ethanol dispensing pumps to be
identified by a small, square, orange
and black label with the common
abbreviation or the appropriate percentage for that region.
NISSAN recommends using fuels
that contain no alcohol. However,
fuels containing up to 10% alcohol
may be used, if necessary. To avoid
serious engine damage due to increased cylinder temperature, do
not use fuels that contain more
alcohol than indicated in
“Gasoline containing oxygenates” page 9-4. Also, do not use
fuel additives, fuel stabilizers or fuel
deicers that contain alcohol.
For additional information, see the following
section. (
“Capacities and recommended
fluids/lubricants” page 9-2)
ENGINE OIL RECOMMENDATION
Mobil 1 (0W-40) (100% synthetic) is the factory
fill oil. The VR38 engine with its plasma-sprayed
bores was developed using this oil. NISSAN
cannot ensure proper engine operation and
durability if other 0W-40 synthetic oil is used.
If Mobil 1 (0W-40) is not available, Mobil 1
(10W-40) (100% synthetic) may be used;
however, some performance loss may be
noticed.
See the following section for engine oil and oil
filter recommendation. (
“Capacities and
recommended fluids/lubricants” page 9-2)
COLD TIRE PRESSURES
The label is typically located on the driver side
center pillar or on the driver’s door.
(
“Wheels and tires” page 8-32)
NEW VEHICLE BREAK-IN PROCEDURES RECOMMENDATION
Follow these recommendations for the future
reliability and economy of your new vehicle.
During the first 1,200 miles (2,000 km) of
vehicle use, follow the recommendations outlined in this Owner’s Manual. (
“Break-in
schedule” page 5-39)
[ Edit: 2014/ 12/ 8
Model: R35-D ]
2016 NISSAN GT-R
R35-D
R35-D
Printing: December 2014 (20)
Publication No.: OM16E0 0R35U0
Printed in U.S.A.
2016
OWNER’S MANUAL
For your safety, read carefully and keep in this vehicle.