Catalogue Supplement
Transcription
Catalogue Supplement
SUPPLEMENT Catalogue Supplement H 2-3 4-8 9 10-21 22 23 24-29 30-31 32-34 35 36-37 38-41 42 43 44-46 47-49 50-51 52 53-55 56 57 58-59 Challenger Lifejackets Devocean Life Vests, Combo Skis, Kneeboards, Wakeboards & Towables TREM Lifebuoys and Boarding Ladders. Propeller Bags and Fishing Rod Holders Shakespeare Antennas Marinco/Nicro Ventilation Marinco Spot Lights Marinco/AFI Horns, Wiper Motors, Blades & Arms International Cleaning Products, Professional Antifouling, Bilgex & Intertuf Polymarine Inflatable Boat & Rib Care Weaver Snap Davits Loctite Sealants & Adhesives, Geocel Sealant Captain Tolley’s Creeping Crack Cure Quicksilver Oils & Lubricants Ultraflex GoTech™ Steering System Clean Tabs Water Filtration Mastervolt Mass Combi Ultra, Alpha Alternator Kits and Regulators, Comfort System Marinco/BEP Pro Installer Series Busbars, Fuse Holders & Insulated Studs Thetford Portable & Cassette Toilets Speedfit Plumbing Fittings Hep2O Plumbing Fittings Water Filtration, Wastes & Accumulator Tanks Jerry Cans, Gland Packing & Anti-syphon Lock Valve Johnson Pump Pumps, Radial Blower & Grey Water Tank Lewmar CPX Windlass & HTX Blocks Six Depots Nationwide Aquafax Limited, 1 Dencora Way, Sundon Business Park, Luton, Beds LU3 3HP Aquafax Ltd. (Hamble), 1-2 Mitchell Point, Ensign Business Park, Hamble, Southampton SO31 4RF Aquafax Ltd. (Plymouth), Unit 5 Plymouth Trade Park, 22 Macadam Road, Plymouth PL4 0RU Aquafax Ltd. (Middlewich), Unit 11, Valley Court, Sanderson Way, Middlewich, Cheshire CW10 0GF Aquafax Ltd. (Wroxham), Unit 31, Stalham Road Ind. Estate, Littlewood Lane, Hoveton, Norfolk NR12 8DZ Aquafax Ltd. (Glasgow), 103-105 Barrie Road, Hillington Park, Glasgow G52 4PX E-mail: [email protected] Website: www.aquafax.co.uk Tel:(01582) 568700 Tel:(023) 80457206 Tel:(01752) 669944 Tel:(01606) 841111 Tel:(01603) 781881 Tel: (0141) 8827511 Fax:(01582) 568720 Fax:(023) 80457208 Fax:(01752) 667764 Fax:(01606) 841188 Fax:(01603) 781981 Fax: (0141) 8835111 CATALOGUE SUPPLEMENT - H Challenger Lifejackets NEW RANGE BOAT SAFETY - LIFEJACKETS Our new range of Challenger and Challenger Aqua-Pro life jackets are manufactured in the UK and provide comfortable and reliable personal safety for leisure, professional and commercial requirements. Manufactured to the highest standards, the Challenger range are fully CE approved to ISO 12402. All life jackets have safety yellow colour when inflated. 6-30250 6-30251 6-30255 6-30254 CHALLENGER LIFE JACKETS • SOLAS retroreflective tape to allow light to be reflected back to source in the dark or poor visibility conditions • Choice of manual or automatic with manual override inflation systems • Oral top-up tube and deflation key included • Approved emergency whistle, strong lifting loop and strong synthetic harness webbing included • Suitable for adults over 50kg up to 55'' (140cm) chest • Choice of heavy duty plastic buckle or stainless steel buckle and deck harness options 150N buoyancy • Choice of Navy blue or red covering with Velcro edge for easy re-packing • Fully CE approved to ISO 12402 Buoyancy 150N 150N 150N 150N 150N 150N Webbing Type Waist Belt Waist Belt Waist Belt Waist Belt Waist Belt & Harness Waist Belt & Harness Operation Manual Manual Automatic Automatic Automatic Automatic Colour Navy Red Navy Red Navy Red Part No. 6-30250 6-30251 6-30254 6-30255 6-30260 6-30261 6-30261 6-30260 CHALLENGER JUNIOR LIFE JACKETS • SOLAS retroreflective tape to allow light to be reflected back to source in the dark or poor visibility conditions • Automatic inflation with manual override cylinder inflation • Oral top-up tube and deflation key included • Approved emergency whistle, strong lifting loop and strong synthetic harness webbing included • Suitable for persons from 15-40Kg • Supplied with stainless steel buckle and deck harness • Crotch strap included • 100N buoyancy • Choice of Navy blue or red covering with Velcro edge for easy re-packing • Fully CE approved to ISO 12402 Buoyancy 100N 100N 2 Webbing Type Waist Belt & Harness Waist Belt & Harness Operation Automatic Automatic Colour Navy Red CATALOGUE SUPPLEMENT - H Part No. 6-30276 6-30277 6-30276 6-30277 Challenger Lifejackets BOAT SAFETY - LIFEJACKETS NEW RANGE CHALLENGER AQUA-PRO LIFE JACKETS The Challenger Aqua-Pro life jackets have been ergonomically designed with a slimmer fit, zipped cover with a storm flap. It has a mesh back to improve comfort and provide breathability as well as an integral pocket which allows you to stow away the crotch strap when not in use. The Aqua-Pro is also fitted with a zipped pocket and neoprene neck for added comfort. • SOLAS retroreflective tape to allow light to be reflected back to source in the dark or poor visibility conditions • Single point indicated operating head with automatic and manual override cylinder inflation • Oral top-up tube and deflation key included • Approved emergency whistle, strong lifting loop and strong synthetic harness webbing included • Suitable for persons 50Kg up to 55” (140cm) chest • Supplied with stainless steel buckle and deck harness • Mesh back with integral crotch strap • 170N buoyancy or 300N buoyancy options • Patented Wave Barrier* Technology with 170N Aqua-Pro life jacket • Red and Black zipped cover with quick burst zip • Zipped pocket included • Fully CE approved to ISO 12402 Buoyancy 170N 300N Webbing Type Deck Harness & Crotch Strap Deck Harness & Crotch Strap Operation Automatic Automatic Colour Red/Black Red/Black Part No. 6-30280 6-30284 * Wave Barrier Technology. The patented interlocking lobe design of the bladder used in the AquaPro 170 self-rights the wearer in under five seconds, even if the wearer is unconscious providing an effective wave barrier which prevents the water from being channelled into the wearers airways SPARES & ACCESSORIES CROTCH STRAP Part No. 6-30290 SOLAS LIFEJACKET LIGHT Part No. 6-30292 SPARES KIT SPARES KIT SPARES KIT SPARES KIT SPARES KIT 24g Junior Auto 150/170N 33g Auto 150/170N 33g Manual 275/300N 60g Auto 275/300N 60g Manual Part No. 6-30295 Part No. 6-30296 Part No. 6-30297 Part No. 6-30298 Part No. 6-30294 CHALLENGER SPARES GUIDE Spares kits can be used on other inflation type life jackets using United Mouldings operating heads. Life Jacket Type Challenger Challenger Challenger Challenger Junior Challenger Aqua-Pro Challenger Aqua-Pro Life Jacket Part No. 6-30250 & 51 6-30254 & 55 6-30260 & 61 6-30276 & 77 6-30280 6-30284 Buoyancy 150N 150N 150N 100N 170N 300N Operation Manual Auto Auto Auto Auto Auto Spares Kit Part No. 6-30296 6-30295 6-30295 6-30294 6-30295 6-30297 CATALOGUE SUPPLEMENT - H 3 Devocean Floating Vests NEW RANGE GENERAL BOAT EQUIPMENT - WATERSPORTS 6-32015 6-32001 BEST VEST SIZE CHART: Size Chest Weight S/M 80-100cm >70kg L/XL 100-110cm >70kg XXL/XXXL 110-130cm >70kg PROMO ADULT VEST 6-32005 • Nylon floating device • Universal - One size fits all (Chest: 75-130cm. Weight: 40-100kg) • Available in Yellow or Red • CE-approved according to ISO 12402.5 Size Universal Yellow Part No. 6-32001 6-32011 BEST VEST • Nylon floating device • Nylon side panels for adjustability • Fully adjustable straps for a better fit • Size: S-M, L-XL, XXL-XXXL • Available in Red or Blue • CE-approved according to ISO 12402.5 Red Part No. 6-32005 Size Red Part No. S/M 6-32011 L/XL 6-32012 XXL/XXXL 6-32013 BEAT VEST YOUTH ALLROUND VEST • Nylon youth floating device • Size: Universal (60-70cm chest, 30-40kg weight) • CE-approved according to ISO 12402.5 • Nylon floating device • Size: S, M, L, XL, XXL • Available in Black • CE-approved according to ISO 12402.5 Size S M L XL XXL Part No. 6-32040 Part No. 6-32022 6-32023 6-32024 6-32025 6-32026 ALLROUND VEST SIZE CHART: Size S M L XL Chest 80-90cm 80-100cm 90-100cm 100-110cm Weight 50-60kg 60-70kg >70kg >70kg 6-32040 XXL 100cm+ >70kg BEST VEST EASY BOATING PACKAGE • 5 Nylon boating vests complete with ventilating transparent bag • Content: 2 x S-M, 3 x L-XL • Horseshoe style • Reflective panels and non clog whistle for safety • 100N CE-approved according to ISO 12402.4 Part No. 6-32090 EASY BOATING VEST SIZE CHART: Size S/M L/XL Newton 78 N 113.5 N Weight 50-60kg >60kg 4 Blue Part No. 6-32015 6-32016 6-32017 CATALOGUE SUPPLEMENT - H Easy Vest Devocean Combo Skis & Accessories GENERAL BOAT EQUIPMENT - WATERSPORTS NEW RANGE GLOBE SKI BALANCE SKI GLOBE / BALANCE COMBO SKI • Size: 67'' (170cm) • Beginner – Intermediate RIM combo pair • Can be used as either combo skis or as an entry-level slalom • Foam lined adjustable horseshoe bindings with trigger adjustment • Tunnel shaped bottom for more stability • Bright yellow fins for visibility Globe: Part No. 6-32120 Balance: Part No. 6-32122 LYNX SKI LYNX COMBO SKI • Size: 65'' (165cm) • Beginner – Advanced wide RIM combo pair • Can be used as either combo skis or as an entry-level slalom • Wider tip profile and double V bottom for additional stability with deep water starts • Great skis to teach people how to ski and providing added confidence to skiers of all levels • Foam lined adjustable horseshoe bindings with trigger adjustment • Bright yellow fins for visibility Part No. 6-32124 GLOBE JUNIOR SKI CREATURE TRAINER SKI GLOBE JUNIOR COMBO SKI CREATURE TRAINER COMBO SKI • Size: 59'' (150cm) • Beginner – Intermediate RIM combo pair for junior skiers • Can be used as either combo skis or as an entry-level slalom • Foam lined heel adjustable horseshoe bindings with trigger adjustment • Tunnel shaped bottom for more stability • Bright yellow fins for visibility • Size: 45'' (117cm) • Wooden marine coated combo pair for kids • Adjustable horseshoe bindings with trigger adjustment • Comes with special handle and rope attachment • Extra towrope and handle included • Stabilizing bar inserts • Line between skis for stability Part No. 6-32126 Part No. 6-32127 SPARE SLALOM TOE Adult: Part No. 6-32147 COMBO FIN Part No. 6-32148 COMBO SKIS SPARE FRONT TOE SPARE SQUEEZE HEEL Adult: Part No. 6-32140 Junior: Part No. 6-32141 Trainer: Part No. 6-32142 Adult: Part No. 6-32143 Junior: Part No. 6-32144 Trainer: Part No. 6-32145 Wide Track Traditional Length 59" 62" 65" 46" 59" 67" Weight up to 59kg 36-73kg 50kg and up up to 33kg up to 54kg 50kg and up Binding Size (EU-US) 35-40 37-45 37-45 >36 / > 4,5 35-40 / 3.5 - 7 37-45 / 5.5 - 11.5 CATALOGUE SUPPLEMENT - H 5 Devocean Kneeboard, Wakeboard, Towables NEW RANGE GENERAL BOAT EQUIPMENT - WATERSPORTS TRIUMPH KNEEBOARD ATTITUDE WAKEBOARD PACKAGE • Handle-hook allows you to get up easy and quickly • Bevelled edge • Ergonomic kneepad • Strong 3.3'' webbing strap, neoprene padded, with easy opening handle • Includes shock-strap which absorbs big blows on the water • Length: 143.5cm • Width: 53.5cm • Weight: 6kg Attitude 139 Wakeboard and Explore Bindings (Standard or XL sizes) Finally a board that actually performs like all riders want! It’s easy to ride straight behind the boat when you wish to, but when you want to cut out hard and make turns, rolls and spins this board is also the one for you. • Continuous rocker • Fiberglass and formica reinforced foam core • Ultra light RIM construction • Two 0.9'' plastic center fins • Performance level: Intermediate • 8'' insert setup • Length: 139cm, Tip/tail Width: 26cm Centre Width: 41cm • Rider weight: 50-90kg Part No. 6-32100 Standard Package: 38.5 - 45cm bindings Part No. 6-32110 XL Package: 43 - 48cm bindings Part No. 6-32111 Top Design CRYPTO TOWABLE TWINS TOWABLE Deflated size: 53.5'' x 55.5'' (136 x 141cm) • Nylon cover / Heavy duty PVC • 4 EVA foam soft-grip handles • 1 air chamber • Water drain, big stem valve and buoyancy chamber • Rider capacity: 1 person Deflated size: 76'' x 60'' (193 x 152cm) • Nylon cover / Heavy duty PVC • 4 EVA foam soft-grip handles with neoprene knuckle guards • 1 air chamber • Water drains, big stem valve and buoyancy chamber • Rider capacity: 2 persons Part No. 6-32170 Part No. 6-32172 MUSKETEER TOWABLE Deflated size: 96'' x 54'' (244 x 137cm) • Nylon cover / Heavy duty PVC • 6 EVA foam soft-grip handles with neoprene knuckle guards • 1 air chamber • Water drains, big stem valve and buoyancy chamber • Rider capacity: 3 persons Part No. 6-32174 6 CATALOGUE SUPPLEMENT - H Bottom Design ROCKET TOWABLE Deflated size 3 men: 109'' (277cm) • Full nylon cover / Heavy duty PVC • EVA-foam filled comfort grip handles • Neoprene comfort seat pads • 3 Air chambers, including side floats • Quick connector • Water drains • Covered Boston valve and 2 speed valves Part No. 6-32176 Devocean Towables GENERAL BOAT EQUIPMENT - WATERSPORTS NEW RANGE SUNDOWN PACKAGE Included: Sundown, wrist seal, quick release, orange flag, foot pump and rope for towables. Part No. 6-32161 ECLIPSE TOWABLE SUNDOWN TOWABLE Deflated size: 54'' (137cm) • Nylon cover / Heavy duty PVC • Water drain, big stem valve & buoyancy chamber • 1 air chamber • 2 EVA foam soft-grip handles • Rider capacity: 1 person Part No. 6-32162 Deflated size: 48'' (122cm) • Nylon cover / Heavy duty PVC • Water drain, big stem valve & buoyancy chamber • 1 air chamber • 2 EVA foam soft-grip handles • Rider capacity: 1 person Part No. 6-32160 MAX TOWABLE SPEED Adults: 32KMH (20MPH) Youth: 24KMH (15MPH) G-FORCE TOWABLE GIANT TOWABLE Deflated size: 58'' (147cm) • Full nylon cover / Heavy duty PVC • 4 EVA foam soft-grip handles with neoprene knuckle protectors • 1 air chamber • Water drain, covered Boston valve and buoyancy chamber • Rider capacity: 1 person Part No. 6-32164 Deflated size: 71'' (181cm) • Nylon cover / Heavy duty PVC • 8 EVA foam soft-grip handles with Neoprene knuckle guards • 1 air chamber • Water drain, Boston valve and buoyancy chamber • Rider capacity: 3 persons Part No. 6-32166 COIN 1 Deflated size: 54" (138cm) • Full nylon cover / Heavy duty PVC • 3 comfortable neoprene pads • 4 EVA foam soft-grip handles with neoprene knuckle guards • 1 webbing handle • 1 air chamber • Water drain, big stem valve and buoyancy chamber • Rider capacity: 1 person Part No. 6-32180 COIN 2 COIN 3 Deflated size: 70" (178cm) • Improved quality full nylon cover / Heavy duty PVC • 3 comfortable neoprene pads • 6 EVA foam soft-grip handles with neoprene knuckle guards • 2 webbing handles • 1 air chamber • 2 water drains, big stem valve & buoyancy chamber • Rider capacity: 2 persons Part No. 6-32182 Deflated size: 80" (203cm) • Improved quality full nylon cover / Heavy duty PVC • 3 comfortable neoprene pads • 6 EVA foam soft-grip handles with neoprene knuckle guards • 4 webbing handles • 1 air chamber • Water drain, big stem valve and buoyancy chamber • Rider capacity: 3 persons Part No. 6-32184 CATALOGUE SUPPLEMENT - H 7 Devocean Ropes and Handles NEW RANGE GENERAL BOAT EQUIPMENT - WATERSPORTS TOW ROPE FOR TOWABLES BOSTON VALVE Specs: 50ft (15m) Part No. 6-32210 Spare inflation valve for towables. Part No. 6-32199 STANDARD ROPE BRIDLE HEAVY DUTY TOW ROPE Length of the rope can easily be adjusted. Galvanized hooks. Part No. 6-32202 Specs: 55ft (17m) • For towing up to a maximum of four people • Ideal for water sleds and multi person towables • 16 strands, 84 filaments rope • Break strength: 4100lbs (1859kg) • Float attachment Part No. 6-32211 WEB BRIDLE Length of the webbing can easily be adjusted. Galvanized hooks. Part No. 6-32203 WAKEBOARD ROPE RECREATIONAL SKI ROPE • 60ft mainline • 5ft, 11'' smooth foam grip handle with wooden bar • 8 strand ski line • Recreational and fun line Part No. 6-32220 • 2 section 70ft mainline • 5ft, 12'' smooth rubber grip handle Part No. 6-32224 CHALLENGE SERIES ROPE NOVA SKI ROPE • 60ft mainline • 5ft, 11'' Machined EVA grip handle • 12 strand ski line • Finger protection on handle for safety Part No. 6-32221 See Section 6 for Pumps for Inflatables SPARES FOR BRAVO INFLATABLES Closing Clip for Bravo 7/8/9/10 Part No. 6-62061 Hose Pump Adaptor Bravo 1/2/7/8/9/10 Part No. 6-62060 Adaptor Set for Electric Inflators Part No. 6-62062 8 • 4 or 8 section 70 ft mainline • 5ft, 12'' machined smooth rubber grip handle • Constructed from the finest polypropylene • Sectioned for the perfect rope length • 8 section version meets official comp. demands 4 Section: Part No. 6-32227 8 Section: Part No. 6-32228 CATALOGUE SUPPLEMENT - H Adaptor Set for Hand/Footpumps Part No. 6-62063 Replacement Hose Kits Bravo 6 & 12 Part No. 6-62064 Bravo 1/2/7/8/9/10 Part No. 6-62065 Miscellaneous Boat Equipment GENERAL BOAT EQUIPMENT TREM HORSESHOE LIFEBUOY Manufactured in stainless steel. Suitable for rubber boats transom. Pipe Ø: 25mm Width: 220mm Length: 740mm Weight: 2.3kg Part No. 6-25041 Made of cellular foam with highly resistant PVC cover. Part No. 6-25532 6-25533 Buoyancy 15kg 15kg NEW RANGE TREM 3 STEP S/S BOLT-ON BOARDING LADDER Colour Orange Yellow For More TREM Products See Our Section 6 catalogue TREM SUPPORTS For Self Inflating Lifecraft Complete with belt with fastening buckle. Can be applied both in horizontal and vertical position. Width: 42cm+ Part No. 6-25619 PROPELLER BAGS Five sizes of orange PVC propeller bags with a draw string at the neck. To comply with the law these must be placed over the propeller when the boat is being trailed. Part No. 6-20900 6-20901 6-20902 6-20903 6-20904 Size Small Medium Large XL XXL Dimensions 40 x 40cm 50 x 50cm 63 x 63cm 67 x 65cm 92.5 x 77.5cm For engines Up to 6hp 6hp to 40hp Large motors inc outboards Large motors inc outboards Large motors inc outboards FISHING ROD HOLDERS WHITE PLASTIC FIXED ROD HOLDER Inner diameter: 40mm 45° angle Part No. 6-22750 S/S 45° FIXED ROD HOLDER S/S FLUSH MOUNT ROD HOLDER SIDE/WALL MOUNT ROD HOLDER With black hole cover Inner diameter: 42mm 45° angle Part No. 6-22752 Black plastic inner & flange Inner diameter: 42mm Flange: 88 x 115mm Overall length: 210mm 90° angle Part No. 6-22754 In 316 stainless steel with white PVC top sleeve Overall length: 254mm Inner diameter: 40mm Inner tube dia.: 48.8mm Part No. 6-22760 SINGLE WALL MOUNT ROD HOLDER Inner diameter: 40mm Part No. 6-22761 CATALOGUE SUPPLEMENT - H 9 Shakespeare Antennas GENERAL BOAT EQUIPMENT - ANTENNAS NEW RANGE SHAKESPEARE HELICAL VHF ANTENNAS HA156C HELIFLEX 5912 RUBBER DUCK Part No. 6-09000 Part No. 6-09002 • Lightweight, low windage, compact helical VHF antenna for short range communications • A favourite for racing yachts and sports boats • Integral aluminium masthead mounting bracket • 20m of RG-58 cable and PL-259 connector • Antenna length: 0.15m (0.5ft) • Gain: 1dB MD 23N • Lightweight, low windage, compact helical VHF antenna for short range communications • Ideal for emergency or temporary installations and particularly suitable for cabin or console tops • Attached and detaches with ease using supplied flush mounting kit • Gold plated connectors supplied • Antenna length: 0.18m (0.6ft) • Gain: 1dB • Heavy-duty helical VHF antenna for short range communications • Ideal for sail and power boats to withstand the most rugged conditions • Watertight, strong, lightweight (0.3kg) construction • Electronics are sealed in epoxy for additional protection • Fitted with ‘N’ Jack to allow detachable cable (no bracket) • Compatible with RG-58 cable • Antenna length: 0.3m (1ft) • Gain: 1dB Part No. 6-09005 SHAKESPEARE STAINLESS STEEL VHF ANTENNAS 5215 SQUATTY BODY® YWX WHIPFLEX™ • Stainless steel whip VHF antenna for sail boats • Unique solderless watertight masthead connector system for easy installation and dismounting • Lightweight - 0.15 kilo with bracket • Includes 180mm cranked masthead nylon mounting bracket • 20m of RG-58 cable and PL-259 connector • Antenna length: 0.9m (3ft) • Gain: 3dBi Part No. 6-09010 • Stainless steel whip VHF antenna for sail boats • Lightweight and low profile • Removeable whip • SO-239 (UHF) connector in base • Sealed, tin-plated copper wire coil • Stainless steel “L” bracket supplied for mast mounting or use optional 4716 or 4717 mast head mounts (p.19) • Antenna length: 0.9m (3ft) • Gain: 3dBi Part No. 6-09013 YHK HAWK™ 6-09020 Detail 6-09011 6-09010 10 • Heavy-duty stainless steel whip ‘lift and lay’ VHF antenna • Ideal for sports fishing boats and smaller power boats • Simple to set up and lay down, ensuring the antenna does not obstruct when fishing or storing the boat • SO-239 (UHF) connector in base • Whip is user replaceable • Sealed, tin-plated copper wire coil • Stainless steel “L” bracket supplied • Antenna length: 0.9m (3ft) • Gain: 3dBi Part No. 6-09020 • Stainless steel whip VHF antenna with ‘Hawk’ windex for sail boats • Unique solderless watertight masthead connector system for easy installation and dismounting • Lightweight - 0.15 kilo with bracket • Includes 180mm flat masthead nylon mounting bracket • 20m of RG-58 cable and PL-259 connector • Antenna length: 0.9m (3ft) • Gain: 3dBi Part No. 6-09011 5247-A LIFT ‘N’ LAY CATALOGUE SUPPLEMENT - H 6-09013 6-09020 Shakespeare Antennas GENERAL BOAT EQUIPMENT - ANTENNAS 5250 SKINNY MINI™ • Compact, lightweight, stainless steel whip VHF antenna • Ideal for small power boats • Sealed, tin-plated copper wire coil • 4.5m of RG-58 cable plus PL-259 plug included. Requires a mount with centre hole for cable • Suggested mounts: 4187, 5187, 4188-S or 4190 (p.19) • Chromed brass ferrule • Antenna length: 0.9m (3ft) • Gain: 3dBi Part No. 6-09021 NEW RANGE SHAKESPEARE STAINLESS STEEL VHF ANTENNAS YRR RIB RAIDER™ • Black (YRR) or White (YRR-W), stainless steel VHF antenna for short range communications • Designed to avoid snagging and excessive whip action, ideal for RIBs and high speed craft • Solderless connector system for ease of installation and removal • Integral bracket with mounting holes • 8m of RG-58 cable with PL-259 connector • Antenna length: 0.48m (1.6ft) • Gain: 1dB 5241-R • Heavy duty stainless steel whip VHF antenna • Ideal for fast sports boats, RIBs and small fishing boats • Whip is user replaceable • 4.5m of RG-58 cable plus PL-259 plug included. Requires a mount with centre hole for cable • Suggested mounts: 4187, 5187, 4188-S or 4190 (p.19) • Chromed brass ferrule • Antenna length: 0.9m (3ft) • Gain: 3dBi Part No. 6-09022 (YRR - Black) Part No. 6-09023 (YRR-W - White) Part No. 6-09025 6-09023 6-09021 6-09025 6-09022 MD 20N • Heavy duty stainless steel whip VHF antenna • Ideal for sail and power boats to withstand the most rugged conditions • Watertight, strong, lightweight (0.2kg) construction • Electronics are sealed in epoxy for additional protection • Fitted with ‘N’ Jack to allow detachable cable (no bracket) • Antenna length: 0.9m (3ft) • Gain: 3dBi Part No. 6-09026 5911 THE STOWAWAY™ • Short VHF whip antenna with flexible outer covering • Ideal as a temporary, spare or emergency antenna • Supplied with 3.6m of cable and PL-259 connector • Rubber suction cup for easy mounting • Velcro storage strips included • Packed in a 50cm, weather resistant, retail plastic tube • Antenna length: 0.25m (0.8ft) • Gain: 1dB Part No. 6-09030 6-09030 SL 156 SHORELINK™ • Emergency VHF antenna for instant set up if your main antenna becomes broken or disabled • Sealed in a waterproof 24cm weather resistant plastic tube • Stored easily on bulkhead or in flare pack • 6m of miniature coaxial cable (RG-174) with PL-259 connector fitted • Compulsory for R.O.R.C. racing • Antenna length: 0.4m (1.3ft) • Gain: 1dB 6-09032 Part No. 6-09032 CATALOGUE SUPPLEMENT - H 11 Shakespeare Antennas GENERAL BOAT EQUIPMENT - ANTENNAS NEW RANGE SHAKESPEARE FIBREGLASS VHF ANTENNAS 426-N • White fibreglass VHF antenna • Designed for high speed sports boats and RIBs working in rough conditions • Quality copper cable elements for good range and efficiency • Includes 4.5m RG-58 cable and PL-259 connector (not attached) • Suggested mounts: 4186, 4721 or 4722 (p.19) • Nylon ferrule • Antenna length: 1.2m (4ft) • Gain: 3dBi Part No. 6-09040 5104 CENTENNIAL™ 5400-XT / 5401-XT LITTLE GIANT™ • Durable, smooth, white fibreglass VHF antenna with polyurethane finish that will not yellow in the sun. • A good looking and superb value antenna, ideal for power and work boats • Brass and copper elements for extra performance • Includes 4.5m RG-58 cable and PL-259 connector (not attached) • Suggested mounts: 4187 or 5187 (p.19) • Chromed brass ferrule • Antenna length: 1.2m (4ft) • Gain: 3dBi • Heavy-duty, high gloss, smooth Galaxy white (5400-XT) or black (5401-XT) fibreglass VHF antenna with polyurethane finish that will not yellow in the sun. • Centre-fed 1⁄2 wave coaxial sleeve • An outstanding, heavy-duty antenna, ideal for power boats, work and fishing boats operating in all types of conditions • Brass and copper elements to maximise range and performance • 6m RG-8X ultra low loss cable and PL-259 connector (not attached) • Matches 5420-XT / 5421-XT AM/FM antennas (p.16) • Suggested mounts: 4187 or 5187 (p.19) • Stainless steel ferrule • Antenna length: 1.2m (4ft) • Gain: 3dBi Part No. 6-09041 6-09040 6-09041 5400-XP • Heavy-duty, high gloss, smooth Galaxy white fibreglass VHF antenna with polyurethane finish that will not yellow in the sun • “Silver Series” (extends transmit/receive performance) • Centre-fed 1⁄2 wave coaxial sleeve • Exceptionally efficient performing, heavy-duty antenna, ideal for serious power boat, work and fishing boat operators in all types of conditions • Stranded high quality tinned copper inner conductor maximises signal strength, combined with the copper and silver plated brass elements will extend performance and life • 6m RG-8X ultra low loss cable and PL-259 connector (not attached) • Suggested mounts: 4187 or 5187 (p.19) • Stainless steel ferrule • Antenna length: 1.2m (4ft) • Gain: 3dBi 427-N & 427-N KIT • Durable smooth gloss finished white fibreglass VHF antenna • Very good value, this antenna is ideal for power and work boats • Brass and copper elements for extra performance • Includes 6m RG-58 cable and PL-259 connector (not attached) • Matches 5350-N AM/FM antenna (p.16) • Suggested mounts: 4186 or 4721 or 495-B (p.19-20) • Nylon ferrule • Antenna length: 1.5m (5ft) • Gain: 3dBi Part No. 6-09050 • Durable smooth gloss finished white fibreglass VHF antenna • A very good looking antenna, ideal for power and work boats • Brass and copper elements for extra performance • Includes 6m RG-58 cable and PL-259 connector (not attached) • Matches 5350-S AM/FM antenna, (p.16) • Suggested mounts: 4187 or 5187 (p.19) • Stainless steel ferrule • Antenna length: 1.5m (5ft) • Gain: 3dBi Part No. 6-09051 427-N Kit as above but with 4186 nylon rachet mount supplied and packaged in a box Part No. 6-09052 (Kit) 6-09052 6-09051 Part No. 6-09045 6-09045 12 427-S CATALOGUE SUPPLEMENT - H 6-09050 6-09043 6-09042 Part No. 6-09042 (5400-XT - White) Part No. 6-09043 (5401-XT - Black) Shakespeare Antennas GENERAL BOAT EQUIPMENT - ANTENNAS 5206-N / 5206-C • Economical, lightweight, white fibreglass VHF antenna • Attractive antenna for good communications where range is not a predominant factor, ideal for power boat applications • Quality copper cable elements for good range and efficiency • Includes 4.5m RG-58 cable and PL-259 connector (not attached) • 5206-N: Nylon ferrule. Suggested mount 4186 (p.19) • 5206-C: Chromed brass ferrule. Suggested mount 4187 or 5187 (p.19) • Antenna length: 2.4m (8ft) • Gain: 6dBi 5206-BL-C 5101-S • Economical, lightweight, black fibreglass VHF antenna • With an attractive black finish this antenna is ideal for power boats and for good communications where range is not a predominant factor • Quality copper cable elements for good range and efficiency • Includes 4.5m RG-58 cable and PL-259 connector (not attached) • Suggested mounts 4187 or 5187 (p.19) • Chromed brass ferrule • Antenna length: 2.4m (8ft) • Gain: 6dBi • Durable, smooth, white gloss fibreglass VHF antenna • Good looking and excellent value, ideal for power and work boats • Brass and copper elements for extra performance • Includes 6m RG-58 cable and PL-259 connector (not attached) • Twin to 5120-S AM/FM antennas (p.17) • Suggested mounts 4187 or 5187 (p.19) • Stainless steel ferrule • Antenna length: 2.4m (8ft) • Gain: 6dBi Part No. 6-09062 Part No. 6-09063 Part No. 6-09060 (5206-N) Part No. 6-09061 (5206-C) 6-09062 Detail 6-09061 Detail 6-09060 5225-XT • Heavy-duty, high gloss, smooth Galaxy white fibreglass VHF antenna with polyurethane finish that will not yellow in the sun • Collinear-phased 5/8 wave elements • An outstanding performing, heavy-duty antenna, ideal for power boats, work and fishing boats operating in all types of conditions • Brass and copper elements to maximise range and performance • Includes 6m RG-8X ultra low loss cable and PL-259 connector (not attached) • Matches 5235-XT AM/FM antenna (p.17) • Suggested mounts 4187 or 5187 (p.19) • Stainless steel ferrule • Antenna length: 2.4m (8ft) • Gain: 6dBi Part No. 6-09065 NEW RANGE SHAKESPEARE FIBREGLASS VHF ANTENNAS 6-09063 Detail 6-09062 6-09061 6-09063 399-1 5225-XP • Heavy-duty, high gloss, smooth Galaxy white fibreglass VHF antenna with silver plated elements and polyurethane finish that will not yellow in the sun • “Silver Series” (extends transmit/receive performance) • Collinear-phased 5/8 wave elements • Exceptionally efficient, heavy duty antenna, ideal for superyachts, work and fishing boat operators requiring extended communications in all types of conditions • Stranded high quality tinned copper inner conductor maximise signal strength, combined with the copper and silver plated brass elements will provide extended performance and life • Includes 6m RG-8X ultra low loss cable cable and PL-259 connector (not attached) • Suggested mounts 4187 or 5187 (p.19) • Stainless steel ferrule • Antenna length: 2.4m (8ft) • Gain: 6dBi • Heavy-duty, smooth, two-sectioned white gloss fibreglass VHF antenna • Collinear phased 5/8 wave with two coaxial chokes to suppress cable radiation • A highly efficient, professional quality antenna combining strength and performance • Brass and copper elements • 4.5m RG-58 cable and PL-259 connector (not attached) • 2 sections: base 1.9m, tip 1m • Suggested mounts 409-R or 410-R for deck or side mounting (p.20) • Chromed brass ferrule • Antenna length: 3m (9.6ft) • Gain: 6dBi Part No. 6-09070 Mount not included. 6-09070 Part No. 6-09068 6-09065 6-09068 CATALOGUE SUPPLEMENT - H 13 Shakespeare Antennas GENERAL BOAT EQUIPMENT - ANTENNAS NEW RANGE SHAKESPEARE FIBREGLASS VHF ANTENNAS 5399 • Heavy-duty, high gloss, smooth Galaxy white, two section fibreglass VHF antenna with polyurethane finish that will not yellow in the sun • Collinear phased 5/8 wave with two coaxial chokes to suppress cable radiation • Strong, sturdy and self supporting, providing exceptional performance for commercial, fishing and leisure applications in all conditions • Brass and copper elements for maximum range and efficiency • 6m RG-8X ultra low loss cable and PL-259 connector (not attached) • 2 sections: base 1.9m, tip 1m • Suggested mount 410-R mounting kit (p.20) • Stainless steel ferrule • Antenna length: 3m (9.7ft) • Gain: 6dBi Part No. 6-09072 SHAKESPEARE SSB / HF ANTENNA 5230 • Heavy-duty, high gloss, smooth Galaxy white, two sectioned white fibreglass VHF antenna with polyurethane finish that will not yellow in the sun • 5/8 wave over 1⁄2 wave dipole. The most effective 8dB antenna system available • Outstanding antenna, ideal for commercial, fishing and superyacht applications in all conditions • Brass and copper elements for maximum range and efficiency • 6m RG-8X ultra low loss cable and PL-259 connector (not attached) • 2 sections: base 2.4m, tip 1.9m • Suggested mounts 409R or 410-R mounting kit (p.20) • Stainless steel ferrule • Antenna length: 4.3m (14.1ft) • Gain: 8dBi 6-09073 SHAKESPEARE SPECIALITY COMMERCIAL VHF ANTENNAS MD 70 MD 7A • Extra heavy-duty, white, tapered, mast or rail mount, end-fed fibreglass antenna • Ideal for work boats and fishing vessels working in the toughest environments • Brass and copper elements for improved performance • Integral, cast aluminium mounting base with white gloss finish • Mounts easily to rail and masts using supplied U bolts • 1m RG213 with N Jack • Aluminium ferrule • Antenna length: 1.5m (4.9ft) • Gain: 3dBi • Extra heavy-duty, mast mount, white fibreglass dipole antenna • Ideal for the extreme conditions found on fishing vessels in the North Sea type of environment and on dhows in the Indian Ocean • Aluminium and copper elements for improved performance • Supplied with extra heavy-duty galvanised steel clamp set for mast mount • 1m RG213 with N Jack • Antenna length: 1.6m (5.2ft) • Gain: 3dBi Part No. 6-09083 Part No. 6-09082 6-09082 14 6-09083 CATALOGUE SUPPLEMENT - H • Heavy-duty, smooth gloss, white, three section, fibreglass SSB antenna • Permanently sealed full length conductors with no loading coil • Reinforced insulation to allow power up to 1kW • Excellent value, this award winning antenna is a high performing HF communicator • Side termination band • 3 sections: base 2.3m, middle 2.3m, tip 2.3m • Suggested mounts 409R or 410-R mounting kit (p.20) • Chromed brass ferrule • Antenna length: 7.0m (23ft) • Gain: 1kW Part No. 6-09104 Mount not included. Part No. 6-09073 6-09072 393 6-09104 For Deck and Rail Mounts, see page 19 Shakespeare Antennas GENERAL BOAT EQUIPMENT - ANTENNAS HA 156C-AIS • Lightweight, low windage, compact helical AIS antenna • A favourite for racing yachts and sports boats • Integral aluminium mounting bracket • 20m of RG-58 cable and PL-259 connector • Antenna length: 0.15m (1ft) • Gain: 1dBi Part No. 6-09120 MD 23-AIS • Extra heavy-duty helical AIS antenna for short range communications • Ideal for sail and power boats to withstand the most rugged conditions • Watertight, strong, lightweight (0.3kg) construction • Electronics are sealed in epoxy for additional protection • Supplied with 20m RG-58 cable plus PL-259 connector and 180mm aluminium bracket • Antenna length: 0.3m (1ft) • Gain: 1dB Part No. 6-09121 NEW RANGE SHAKESPEARE AIS ANTENNAS 5215-AIS SQUATTY BODY® • Stainless steel whip AIS antenna for sail boats • Strong, lightweight and low profile antenna with removeable whip • SO-239 (UHF) connector in base • Sealed, tin-plated copper wire coil for performance and reliability • Stainless steel “L” bracket supplied for mast mounting or use optional 4716 or 4717 mast head mounts (p.20) • Matches 5215 (VHF) • Antenna length: 0.9m (3ft) • Gain: 3dBi Part No. 6-09125 6-09120 6-09121 5250-AIS SKINNY MINI™ • Compact, strong, lightweight, stainless steel whip AIS antenna • End fed 1⁄2 wave stainless steel whip with chrome plated brass canister • Ideal for small power boats • Matches 5250 (VHF) • 4.5m of RG-58 cable plus PL-259 plug. Requires a mount with centre hole for cable • Suggested mounts: 4187, 4188-S (p.19) • Chromed brass ferrule • Antenna length: 0.9m (3ft) • Gain: 3dBi Part No. 6-09126 AIS-MAST • Heavy-duty stainless steel whip AIS antenna • Ideal for sail and power boats to withstand the most rugged conditions • Watertight, strong, lightweight (0.2kg) construction • Electronics are sealed in epoxy for additional protection • Matches YWX (VHF) • 20m RG-58 cable plus PL-259 connector and 180mm nylon cranked bracket • Antenna length: 0.9m (3ft) • Gain: 3dBi Part No. 6-09127 6-09126 Detail 6-09125 5396-AIS LITTLE GIANT™ • Heavy-duty, high gloss, smooth, Galaxy white, fibreglass VHF antenna with polyurethane finish that will not yellow in the sun • End-fed 1⁄2 wave coaxial sleeve • Specially designed for AIS systems, ideal for power boats, work and fishing boats operating in all types of conditions • Brass and copper elements to maximise range and performance • 6m RG-8X ultra low loss cable and PL-259 connector (not attached) • Suggested mounts 4187 or 5187 (p.19) • Stainless steel ferrule • Antenna length: 1.2m (3.9ft) • Gain: 3dBi AIS-COM • Heavy-duty, mast mount, white fibreglass dipole AIS antenna • Specially designed for the extreme conditions found on fishing vessels in the North Sea type of environment and on dhows in the Indian Ocean • Aluminium and copper elements for improved performance • Supplied with extra heavyduty galvanised 4715 steel clamp set for mast mount • 1m RG213 with N Jack • Antenna length: 1.6m (5.2ft) • Gain: 3dBi Part No. 6-09134 Part No. 6-09130 6-09127 6-09126 6-09130 6-09134 CATALOGUE SUPPLEMENT - H 15 Shakespeare Antennas GENERAL BOAT EQUIPMENT - ANTENNAS NEW RANGE SHAKESPEARE AM / FM ANTENNAS 4351 YRR AM/FM RIB RAIDER™ 4350 • Black stainless AM/FM antenna • Designed to avoid snagging and excessive whip action, ideal for RIBs and high speed craft • Matches YRR (VHF) • Integral black bracket with mounting holes • 4.5m of RG-62 cable with Motorola type connector • Antenna length: 0.48m (1.6ft) • White fibreglass AM/FM antenna • Features Shakespeare’s exclusive distribution load for improved reception • Integral polycarbonate Lift and Lay mount • 3m of RG-62 cable with Motorola type plug • Nylon ferrule • Antenna length: 1.0m (3.3ft) Part No. 6-09141 Part No. 6-09143 • White fibreglass AM/FM antenna • Features Shakespeare’s exclusive distribution load for improved reception • 3m of RG-62 cable with Motorola type plug • Suggested mount style 4186 (p.19) • Nylon ferrule • Antenna length: 1.0m (3.3ft) Part No. 6-09142 6-09143 6-09141 6-09142 5350-N 5420-XT / 5421-XT LITTLE GIANT™ • Durable, smooth, gloss finished, white fibreglass AM/FM antenna • Good performance AM/FM antenna, ideal for power and work boats • Includes 4.6m RG-62 cable plus Motorola plug attached • Matches 427-N VHF antenna • Suggested mounts: 4186 (p.19) • Nylon ferrule • Antenna length: 1.5m (5ft) • Heavy-duty, high gloss, smooth Galaxy white (5420XT) or black (5421-XT) fibreglass AM/FM antenna with polyurethane finish that will not yellow in the sun. • An outstanding, heavy-duty antenna, ideal for power boats, work and fishing boats operating in all types of conditions • Copper elements to maximise range and performance • 3.7m RG-62 coax cable plus Motorola connector attached • Matches 5400-XT / 5401-XT (VHF), (p.12) • Suggested mounts: 4187 or 5187 (p.19) • Stainless steel ferrule • Antenna length: 1.2m (4ft) Part No. 6-09146 5350-S • Durable, smooth, gloss finished, white fibreglass AM/FM antenna • A good looking and well performing AM/FM antenna, ideal for power and work boats • Includes 4.6m RG-62 cable plus Motorola plug attached • Matches 427-S VHF antenna • Suggested mounts: 4187 or 5187 (p.19) • Stainless steel ferrule • Antenna length: 1.5m (5ft) Part No. 6-09147 6-09147 Detail Part No. 6-09145 (5420-XT - White) 6-09146 Detail 6-09144 6-09145 Part No. 6-09144 (5421-XT - Black) 6-09147 6-09146 16 CATALOGUE SUPPLEMENT - H NOTE: SHAKESPEARE DOES NOT RECOMMEND CABLES RUN LONGER THAN 7.6m WITH AM/FM ANTENNA SYSTEMS. Shakespeare Antennas GENERAL BOAT EQUIPMENT - ANTENNAS 5120-S 5235-XT • Heavy-duty, high gloss, smooth Galaxy white fibreglass AM/FM antenna with polyurethane finish that will not yellow in the sun • Copper elements to maximise reception ranges • An outstanding performing, good looking, heavy-duty AM/FM antenna, ideal for power boats, and superyachts operating in all types of conditions • 6m RG-62 cable plus Motorola plug attached • Matches 5225-XT (VHF) • Suggested mounts 4187 or 5187 (p.19) • Stainless steel ferrule • Antenna length: 2.4m (8ft) • Durable, smooth gloss finished, white fibreglass AM/FM antenna • A good looking and well performing AM/FM antenna ideal for power boats • Includes 4.6m RG-62 cable plus Motorola plug attached • Matches 5101-S VHF antenna • Suggested mounts 4187 or 5187 (p.19) • Stainless steel ferrule • Antenna length: 2.4m (8ft) NEW RANGE SHAKESPEARE AM / FM ANTENNAS 4357-S • VHF to AM/FM converter • For use with VHF antennas where a separate AM/FM antenna is not practical • Ideal for sail boat applications • Does not affect or interfere with the VHF performance • 3m RG-62 cable with Motorola plug (attached) plus 0.9m RG-58 cable for connection to VHF Part No. 6-09150 Part No. 6-09149 6-09150 Part No. 6-09148 6-09149 6-09148 SHAKESPEARE LOUD SPEAKERS AND HAILERS WS200-P HS-5 • Weatherproof Deck Watch Loud Speaker • Can be surface or flush mounted • UV Resistant ABS construction • Can be used on 4 or 8 ohm systems • Overall diameter 14cm, depth 5cm • Hole diameter of 11.6cm for flush mounting • Output 5 watts, Impedance 8 ohms • Weight 0.3 kilo • Blister packed Part No. 6-09200 ES-2 • 5.7cm external speaker with Mylar cone in a compact white housing • 4 ohm speaker, 5 watts (RMS) input • Rachet action mounting bracket • 1.8m cable and 3.5mm phono plug Part No. 6-09202 ES-4 • External Horn Speaker • 12.7cm white plastic horn speaker • 4 ohm speaker, 15 watts (RMS) input Part No. 6-09208 • 10cm deluxe speaker with Mylar cone in white plastic case for protection against moisture • 4 ohm speaker, 8 watts (RMS) input • Swivel mounting bracket • 1.8m cable with 3.5mm phono plug Part No. 6-09204 ES-4P • Same as ES-4 plus built in amplifier for volume control • Switchable attenuator to prevent overload • Max audio level to 94dBA • 3.5mm plug for audio input Part No. 6-09205 CATALOGUE SUPPLEMENT - H 17 Shakespeare Antennas GENERAL BOAT EQUIPMENT - ANTENNAS NEW RANGE SHAKESPEARE ANYWHERE™ TV ANTENNAS & ACCESSORIES Shakespeare AnyWhere™ HDTV antennas have been designed to the highest specification to bring the best possible signal to your TV, either on board, in a caravan or at home. • Receives digital and terrestrial TV signals (DVB-T, ISDB-T, DMBT/H, ATSC) and DAB/FM radio • Waterproof and weatherproof housing - made of UV resistant, injection moulded ASA material for long term durability 18 • Omnidirectional reception - receives VHF, UHF, and FM signals through 360º • Built in high gain and low noise amplifier, shielded for minimum interference • The use of SMD technology and micro electronics in the amplifier ensures outstanding performance • LTE filter is incorporated to eliminate interference from 4G mobile communications SA-HDTV-INDR1 AnyWhere Marine HDTV 8'' SA-HDTV-MAR8 AnyWhere Marine HDTV 8'' • 190W x 120H x 22D mm Indoor & Portable HDTV antenna (with built-in LTE filter). • Newly designed using the latest TV technologies • Attractive, gloss black, compact and slim-line, indoor portable HDTV antenna. Comes with built in high gain, low noise amplifier and LTE filter. Ideal indoors and below decks • Set of screws and suction cups • USB cable • IEC to F connector • AC/DC power adaptor (UK/EURO) • Receiving range FM/VHF/UHF (VHF:87.5 – 230MHz UHF: 470-862) • Gain: 28dB / Noise figure: 3dB • Max. output level: 100 dBµV / Impedance: 75Ω • Outputs: x 2 TV’s Part No. 6-09160 • 203H x 110W mm (8'' x 4.3'') Omni Directional HDTV antenna (with built-in LTE filter) • Newly designed using the latest TV technologies • Compact, lightweight, weatherproof HDTV antenna. Comes with built in high gain, low noise amplifier and LTE filter. Ideal for small power boats and sail boats • Includes amplifier gain control unit • 10m 75 Ohm RG59 cable with 2 x F connectors + IEC to F connector • 1.5m adapt cable fitted with F plug to IEC • Power 12/24V DC - AC/DC power adaptor (UK/EURO) included • Receiving range FM/VHF/UHF (VHF:87-230MHz UHF: 470-862) • Gain: 30dB / Noise figure: 3dB • Max. output level: 110 dBµV / Impedance: 75Ω • Outputs: x 2 TV’s Part No. 6-09162 SA-HDTV-MAR10 AnyWhere Marine HDTV 10'' SA-HDTV-MAR14 AnyWhere Marine HDTV 14'' • 240mm (10'') Omni Directional HDTV antenna (with built-in LTE filter) • Newly designed using the latest TV technologies • Compact, lightweight, white ASA, weatherproof HDTV antenna. Comes with built in high gain, low noise amplifier and LTE filter. Ideal for small power boats and sail boats • Includes amplifier gain control unit • 25m 75 Ohm RG59 cable with 2 x F connectors + IEC to F connector • 1.5m adapt cable fitted with F plug to IEC • Power 12/24V DC - AC/DC power adaptor (UK/EURO) included • Receiving range FM/VHF/UHF (VHF:87-230MHz UHF: 470-862) • Gain: 30dB / Noise figure: 3dB • Max. output level: 110 dBµV / Impedance: 75Ω • Outputs: x 2 TV’s Part No. 6-09164 • 380mm (14'') Omni Directional HDTV antenna (with built-in LTE filter) • Newly designed using the latest TV technologies • Compact, white ASA, weatherproof HDTV antenna. Comes with built in high gain, low noise amplifier and LTE filter. Ideal for power boats and work boats • Includes amplifier gain control unit • 25m 75 Ohm RG59 cable with 2 x F connectors + IEC to F connector • 1.5m adapt cable fitted with F plug to IEC • Power 12/24V DC - AC/DC power adaptor (UK/EURO) included • Receiving range FM/VHF/UHF (VHF:47-230MHz UHF: 470-862) • Gain: 30dB / Noise figure: 3dB • Max. output level: 110 dBµV / Impedance: 75Ω • Outputs: x 2 TV’s Part No. 6-09166 4366 SAILBOAT TV ANTENNA MAST MOUNT TV-4S 4 WAY TV SPLITTER Aluminium mast mount supplied with a 1'' - 14 thread fitting for SA-HDTV-MAR8, MAR10 or MAR14 Part No. 6-09171 • 4 Way splitter for TV antennas • Operating band 5MHz - 1000MKz • Isolation >22dB, damping 6.9 - 8.0dB, 75Ω Impedance • Die cast aluminium construction • Connector type: F connectors CATALOGUE SUPPLEMENT - H Part No. 6-09172 Shakespeare Antennas GENERAL BOAT EQUIPMENT - ANTENNAS 4186 NYLON RACHET MOUNT 4187 S/STEEL RACHET MOUNT • Four-way nylon rachet mount with handle, for deck or side mounting • Standard 1''-14 thread • Quick release lever allows antenna fold-down • For antennas up to 2.4m in self support mode • Stainless steel four-way swivel rachet mount • Standard 1''-14 thread • Quick release lever allows antenna fold-down • Slot centre feed • Sturdy construction, quality finish Part No. 6-09250 Part No. 6-09251 5187 S/STEEL RACHET MOUNT • Sleek s/steel four-way swivel rachet mount • Fine angle control (5 degree steps) • Standard 1''-14 thread • Quick release lever allows antenna fold-down • Slot centre feed • Highly polished finish Part No. 6-09252 4711 NYLON 25mm FLANGE MOUNT NEW RANGE SHAKESPEARE ANTENNA DECK MOUNTS 4710 S/STEEL 25mm FLANGE MOUNT • Heavy duty, 25mm high mount • 70mm diameter base • Ideal for GPS, marine TV and fibreglass antennas up to 1.5m • Standard 1''-14 thread (male) Part No. 6-09253 4365 S/STEEL 110mm FLANGE MOUNT • Moderate duty, low profile 25mm high mount • 70mm diameter base • Ideal for GPS, marine TV and fibreglass antennas up to 1.5m • Standard 1''-14 thread (male) • Stainless steel fixed base mount • Standard 1''-14 thread • 100mm high mount, 75mm dia. base • Ideal for fitting to radar arches • Excellent for GPS & marine TV antennas Part No. 6-09254 Part No. 6-09255 SHAKESPEARE ANTENNA RAIL MOUNTS 4188-S RAIL RACHET MOUNT 4188-SL RAIL RACHET MOUNT • Stainless steel rachet rail mount • Quick release lever for quick, easy lay down • Side slot for cable feed • For 22 / 25mm vertical and horizontal rails • For antennas up to 2.4m in self support mode • Stainless steel rachet rail mount • Quick release lever for quick, easy lay down • Side slot for cable feed • For 25 / 38mm vertical or horizontal rails • For antennas up to 2.4m in self support mode Part No. 6-09260 Part No. 6-09261 4190 RAIL RACHET MOUNT 4721 NYLON RAIL MOUNT • Stainless steel rail rachet mount • Quick release lever allows antenna fold-down • Side slot for cable feed • Suitable for 22mm or 25mm antennas to 2.5m • Nylon rachet rail mount • Attaches to 22mm / 25mm vertical, horizontal and angled rails. Lever action - 1''-14 thread • Has hole for coax cable pass-through Part No. 6-09262 Part No. 6-09263 4722 PLASTIC RAIL MOUNT 4720 S/STEEL RAIL MOUNT • Sturdy plastic rail mount • Attaches to 22mm & 25mm horizontal rails, 1''-14 thread • Slot cable feed • Stainless steel rail and bulk head mount • This clever design allows a neat fit to 22, 25 and 32mm square or round rails • Fits vertical or horizontal rails and flat surfaces • Complete with nylon adapters Part No. 6-09264 Part No. 6-09265 CATALOGUE SUPPLEMENT - H 19 Shakespeare Antennas GENERAL BOAT EQUIPMENT - ANTENNAS NEW RANGE SHAKESPEARE MOUNTS, BRACKETS & ACCESSORIES 495-B LIFT ‘N’ LAY MOUNT 4716 STAND-OFF MAST BRACKET • Nylon Deck Mount • Enables antenna to lift ‘n’ lay with positive snap action • Levelling plate included for mounting to a sloping deck • Standard 1''-14 thread (male) • Includes 3/8''-24 thread brass insert • Durable plastic angled mast mount / stand-off bracket • Mounting screws not included • 12.7cm high x stand-off distance: 20cm Part No. 6-09270 Part No. 6-09256 4717 MAST TOP BRACKET YBR ADAPT3 / ADAPT4 • Flat plastic bracket attaches to the top of a mast for mounting Shakespeare’s low-profile, base-loaded antennas • Mounting screws not included • Attaches easily to any flat, horizontal surface • Dimensions (mm): 9.5 high x 45 wide x 200 long • Right angle bracket as supplied with the RIB Raider (p11 or 16) • Black, aluminium • Screws supplied • 16mm diameter hole • ADAPT3: Adapts SO-239 (UHF) male to 1'' x 14 TPI female thread (chrome plated brass) (converts 5215 & 5247 to 1'' x 14 TPI) Part No. 6-09283 Part No. 6-09273 Part No. 6-09271 • ADAPT4: Adapts M16 male to 1'' x 14 TPI female thread - (converts YRR, YWX, YHK to 1'' x 14 TPI) Part No. 6-09284 SHAKESPEARE COMMERCIAL ANTENNA MOUNTS 4715 MOUNTING CLAMPS • Galvanised steel mounting clamps for mast mount • Size: 260 x 40mm • Aerial / Pole size: 25mm - 50mm dia. • Supplied with rubber inserts • For MD 7A (P.14) Part No. 6-09305 410-R HEAVY DUTY MOUNTING KIT • Combines the 81-S s/s swivel mount with the 408-R moulded upper bracket • Insert to accept 25mm, 28mm, or 38mm diameter antennas or extension masts Part No. 6-09309 AHDVM HEAVY DUTY VERTICAL MOUNT • Stainless steel heavy duty, vertical mount / pole mount with ‘U’ bolts and nuts 1''-14 thread • 90 x 90mm backing plate • 120mm total height Part No. 6-09311 409-R HEAVY DUTY MOUNTING KIT • Combines 407 and 408-R together • 407 is a heavy duty chrome plated brass swivel mount bracket. For deck or side mounting • 408-R is a white moulded heavy duty plastic insulated stand off bracket • Insert to accept 25mm, 28mm, or 38mm diameter antennas or extension masts Part No. 6-09315 20 CATALOGUE SUPPLEMENT - H Shakespeare Antennas GENERAL BOAT EQUIPMENT - ANTENNAS SHAKESPEARE SWITCHES & TESTERS AS-2 VHF AUTOMATIC SWITCH ART-3 VHF TEST METER • Automatic switch toggles two radios to one antenna • When you transmit on one radio, it switches the antenna to it automatically • The radio stays locked onto the antenna, until the switch detects a transmit from the other radio. Easy! • Test receiver function • Output power and VSWR (antenna efficiency) • Internal battery or 12V DC Part No. 6-09322 Part No. 6-09323 NEW RANGE 4700 SERIES EXTENSION MASTS (Heavy Duty) • Heavy-duty stainless steel extension mast • Male upper, female lower 1''-14 threads • Excellent for clearing an obstruction • One Section • Stainless steel ferrule Length 15cm 30cm 60cm Part No. 6-09220 6-09221 6-09222 SHAKESPEARE ANTENNA SPARES & ACCESSORIES ACC105 DECK PLUG AND SOCKET ACC106 DECK PLUG AND SOCKET ACC108 THRU DECK GLAND • Deck plug and socket for RG-58 coaxial cable with N type connectors, shroud and screws complete with 2 protective caps • Blister packed • Deck plug and socket for RG-213 coaxial cable with N type connectors, shroud and screws complete with protective cap • Blister packed • Thru Deck Gland for RG-58 and RG-2113 cable complete with stainless steel screws • Blister packed Part No. 6-09340 Part No. 6-09341 Part No. 6-09342 COAXIAL ANTENNA CABLE CENTERPIN PL-258-CP-G SERIES CENTERPIN PL-259-CP-G SERIES • The easy way to splice coax - for splicing RG-58 A/U, RG-8/X • No soldering or pairing back • For RG-58 A/U, and RG-8/X coaxial cable • For installing a PL-259 connector • No soldering or pairing back Part No. 6-09350 Part No. 6-09351 100m reel of RG-58 Ohm Coaxial Cable Part No. 6-09333 Cross section SHAKESPEARE SPARES YWA YHA YHI Spare antenna for YWX Whiplflex Part No. 6-09010 (p.10) Part No. 16-09010-1 Spare antenna for YHK Hawk Part No. 6-09011 (p.10) Part No. 16-09011-1 Replacement wind indicator for YHK Hawk Part No. 6-09011 (p.10) Part No. 16-09011-2 CATALOGUE SUPPLEMENT - H 21 Marinco Nicro Vents GENERAL BOAT EQUIPMENT - VENTILATION NEW RANGE SOLAR MINI VENT 1000 The MiniVent 1000 is the smallest and most economical solar vent in the Marinco™ line. At just 7" (178mm) in diameter and approximately 13⁄4 " (44mm) high, the MiniVent 1000 is compact yet effective. This solar powered model is an exhaust vent only. It will keep the boat cabin cool when you need it most, during the hot sunlight hours. Under solar power, the Mini Vent 1000 will move 700 cubic feet of air an hour. At night, even a light breeze will continue to ventilate the boat passively. Built-in shut-off damper prevents water intrusion in rough seas. Fits a 33⁄4 " (95mm) diameter installation hole. The vent can be retrofitted to an existing hole of up to 6" (152mm) in diameter. 3" White ABS Plastic Part No. 6-11600 • Solar powered exhaust ventilation during daylight and passive exhaust at night • No batteries or wiring required • Whisper-quiet fan operation • Durable white ABS construction • Shut-off damper to prevent water intrusion in rough seas • Dimensions: 7" (178mm) diameter x 13⁄4 " (44mm) high • All MiniVent 1000 models come complete with white plastic interior trim ring, mounting hardware and an easy-to-understand installation manual. DAY/NIGHT PLUS SOLAR VENT WITH STAINLESS STEEL COVER • Circulates fresh air in boat cabin eliminating mold, mildew and musty air • Moves 1,000 cubic feet of air/hour or 24,000 cubic feet of air/day (4" model) • Rechargeable battery allows for 24-hour continuous operation • Whisper quiet fan operation • No wiring required • Interchangeable intake and exhaust fans • High capacity NiMh battery operates vent for up to 40 hours without sunlight on a full charge • Direct to deck installation • Built-in on/off fan switch • Complete air and green water shut-off from below • All Day/Night PLUS models come complete with two fan blades, white plastic interior trim ring, insect screen, mounting hardware and an easy-to-understand installation manual. • Replaces NICRO 3" & 4" snap-in deck plates (fits existing holes once snap-in deck plates are removed) Size S/Steel P/No. 3'' (76mm) 6-11605 4'' (101mm) 6-11607 White P/No. 6-11606 6-11608 NiMh Nickel Metal Hybrid Battery for Day/Night Plus Vents Replacement battery for current Day/Night Plus vents, as well as, older model PowerVent 3000 and Day / Night 2000 Vents. Part No. 6-11610 • High capacity C-cell battery • 1.2 volts, 2.0 amp-hours • Average life: 3 - 5 years • Environmentally friendly AIR VENT 500 PASSIVE EXHAUST VENTILATION (NON-SOLAR) The AirVent 500 is a non-solar ventilation option that can passively move 600 to 1,000 cubic feet of air per hour in a 15 knot breeze. Marinco's engineering expertise created this vent to be strong, compact and effective. The AirVent 500 is an economical way to provide ventilation in your boat or it can be used in conjunction with other solar powered or 12V vents to create cross flow air circulation. • Compact size: 7" (178mm) diameter x 13⁄4 " (44mm) high • High Air Flow volume 1,000 cu. ft./hour in a 15 knot breeze • Strong U.V. stabilized white ABS construction • Center panel is translucent plastic allowing light to pass through it below deck • Center damper shuts vent off from below • Easy installation - attaches directly to deck in compact 33⁄4 " (95mm) diameter hole and can be retrofitted to an existing hole of up to 6" (152mm) in diameter. SNAP-IN DELUXE LOW PROFILE PVC COWL VENT These vents are a perfect air intake supplement to solar ventilation, and are also commonly used as a bilge ventilating system with or without a mechanical blower. • Soft and durable PVC construction returns to original shape if stepped on • Safer than metal cowl vents - prevents injury and resists snagging lines • Snap-In vents include deck plate and cover • White with bright red interior • Available in 3" or 4" sizes Size Height Part No. • Includes white Snap-in 3" (76mm) 41⁄2 " (114mm) 6-11620 deck plate and cover 4" (101mm) 51⁄2 " (140mm) 6-11621 22 CATALOGUE SUPPLEMENT - H Part No. 6-11611 WHITE SNAP-IN DECK PLATE • Includes Snap-In watertight cover • Use with any Marinco™ Snap-in vent system Size Cut-Out Hole Part No. 3" (76mm) 33⁄4 " Dia. 6-11628 4" (101mm) 43⁄4 " Dia. 6-11629 Marinco Spot Lights GENERAL BOAT EQUIPMENT - SPOT LIGHTS NEW RANGE WIRELESS REMOTE SPOT LIGHT • Universal 12/24 volt circuit with bright 100W, H3 halogen bulb • UV resistant, IP56 Weatherproof ABS housing and Lexan® lens • O-ring sealed housing, designed for the harsh marine environment - moisture, salt, shock and vibration tested • Universal snap-in mounting system (can be mounted upside down) • Super-quiet, all-weather motor with limit stops provides a full range of coverage • 370° sweep and 120° Tilt (75° up and 45° down) • One touch auto sweep and S.O.S. function • Wireless dash mount remote standard; (hard wired & handheld remotes are optional) • Available in white, black and chrome Specifications: Bulb: Power (Input voltage): Current draw (idle/in use): Peak Beam Intensity: Peak Beam Distance: Lux @ 66' (20 m): Coverage at 66' (20 m): Rotation: Tilt: Wireless range: Dimensions (W x H x D): Weight: Housing material: Lens material: Operating temp range: IP Rating: 100 watt, H3 halogen 12V or 24V 0.03 amps / 7.0 amps 210,000 Cp 917 ft (280m) 525 Lux 132 sq ft (12 sq m) 370° (built in limit stops) 120° Tilt (75° up & 45° down) 200 ft (65 m) 7.5" x 7.5" x 9.25" (19cm x 19cm x 23.5cm) 3.30lbs (1.5kg) UV resistant PC/ASA UV resistant Lexan® 5°F – 113°F (-15°C – 45°C) IP56 Description Wireless Remote Spot Light Wireless Remote Spot Light Wireless Remote Spot Light Colour Black White Chrome Part No. 6-11500 6-11501 6-11502 For spare bulbs see Section 8 REMOTE OPTIONS Part No. Remote Specifications: Power Current Draw (idle/in use): Wireless Range: Estimated Battery Life: Dimensions (W x H x D): Weight: Housing Material: Button Material: Operating Temp Range: IP Rating: 6-11512 Included Wireless Bridge Remote 12 or 24 volt (hard wired) negligible 200ft (65m) — 3.5" x 2.25" x 0.75" 88 x 57 x 19mm 2.12 oz (60 g) UV resistant PC/ASA Silicone (glow in the dark) 5°F – 113°F (-15°C – 45°C) IP54 6-11511 (Optional) Hand Held Bridge Remote CR2540 button cell battery negligible 200 ft (65 m) > 40 hours (continuous use) 2.0" x 3.78" x 1" 51 x 96 x 25mm 2.82 oz (80 g) UV resistant PC/ASA Silicone (glow in the dark) 5°F – 113°F (-15°C – 45°C) IP56 6-11513 (Optional) Wired Bridge Remote 12 or 24 volt (hard wired) negligible — — 3.5" x 2.25" x 0.75" 88 x 57 x 19mm 2.12 oz (60 g) UV resistant PC/ASA Silicone (glow in the dark) 5°F – 113°F (-15°C – 45°C) IP54 CATALOGUE SUPPLEMENT - H 23 Marinco AFI Horns NEW RANGE GENERAL BOAT EQUIPMENT - HORNS ELECTRONIC HORN (White Grill) DROP-IN “H” HORN with Grills • Electronic Piezo horn sound • One piece water resistant housing, grill is molded to horn • 107 dB(A) at one meter • Fundamental frequency: 550±100Hz • Mounts in a standard 57mm (2.25") opening • Draws less than 1A, maximum draw: 0.8A • Internal space requirements (W x H x D): 57mm (2.25") x 57mm (2.25") x 50mm (2") • Grill dimensions (W x H x D): 124mm (4.875") x 70mm (2.75") x 127mm (5") Part No. 6-11002 • Comes with both black ABS and white ASA snap-in grills • dB(A) rating: 107 at one meter • Fundamental frequency: 370±20Hz • Internal space requirements (H x W x D): 50mm (2") x 86mm (3.375") x 82mm (3.25") • Distinctive marine horn sound • Enclosed sound unit • Easy installation or retrofit, mounts from the outside • 12 volt, maximum amp draw: 4 amps Part No. 6-11004 SINGLE TRUMPET MINI AIR HORN DUAL TRUMPET MINI AIR HORN DUAL TRUMPET AIR HORNS (24V) • Solid brass construction, chrome plated • Non-corrosive Lexan® polycarbonate diaphragm • Includes compressor, air tubing, fittings, and hardware (12V compressor produces 9-11 PSI) • Dimensions (L x W x H): 241mm (9.5") x 89mm (3.5") x 89mm (3.5") • Maximum amp draw: 12V: 20A • dB rating: 126 at one meter, 1/3 octave band • Fundamental frequency: 630±15Hz Part No. 6-11020 • Solid brass construction, chrome plated • Non-corrosive Lexan® polycarbonate diaphragm • Includes compressor, air tubing, fittings, and hardware (12V compressor produces 9-11 PSI) • Dimensions (L x W x H): 241mm (9.5") x 127mm (5") x 95mm (3.75") • Maximum amp draw: 12V: 20A • dB(A) rating: 127 at one meter, 1/3 octave band • Fundamental frequency: 630±15/525±15Hz Part No. 6-11022 • Chrome plated • Non-corrosive Lexan® polycarbonate diaphragm • Includes compressor, air tubing, fittings, and hardware • Dimensions (L x W x H): 431mm (17") x 178mm (7") x 95mm (3.75") • Maximum amp draw: 24V: 10A • dB rating: 121 at one meter, 1/3 octave band • Fundamental frequency: 375±15/315±15Hz Part No. 6-11027 AIR HORN COMPRESSOR • Replacement compressor fits all Marinco AFI™ Air Horns • Dimensions (D x L): 66mm (2.625") x 127mm (5") • Includes mounting bracket • Maximum amp draw: 20 amps, produces 9 - 11 PSI Part No. 6-11030 (12V) Part No. 6-11031 (24V) 24 CATALOGUE SUPPLEMENT - H MINI HIDDEN HORN • Type 304 stainless steel diaphragm • Dimensions (W x H x L): 82mm (3.25") x 44mm (1.75") x 76mm (3") • Maximum amp draw: 3 amps • dB(A) rating: 105 at one meter • Fundamental frequency: 440±20Hz • This horn is not designed for installation in exposed areas. Part No. 6-11010 SINGLE TRUMPET ELECTRIC HORN (24V) • 100% stainless steel exterior • Type 304 stainless steel diaphragm • Includes laminated horn signal card and stainless steel mounting screws • Dimensions (L x W x H): 419mm (16.5") x 101mm (4") x 120mm (4.75") • Maximum amp draw: 2.5 amps • dB(A) rating: 118 at one meter • Fundamental frequency: 390±15Hz Part No. 6-11041 Marinco AFI Horns GENERAL BOAT EQUIPMENT - HORNS COMPACT DUAL TRUMPET ELECTRIC HORN (12V) • 100% stainless steel exterior • Type 304 stainless steel diaphragm • Dimensions (L x W x H): 355mm (14") x 89mm (3.5") x 101mm (4") • Maximum amp draw: 3.5 amps • dB(A) rating: 108 at one meter • Fundamental frequency: 460±15Hz Part No. 6-11044 • 100% stainless steel exterior • Type 304 stainless steel diaphragm • Dimensions (L x W x H): 406mm (16") x 190mm (7.5") x 101mm (4") • Maximum amp draw: 7 amps • dB(A) rating: 110 at one meter • Fundamental frequency: 460±15/415±15Hz Part No. 6-11046 NEW RANGE COMPACT SINGLE TRUMPET ELECTRIC HORN (12V) MINIBLAST™ COMPACT ELECTRIC HORNS (12V) • Long lasting, non-corrosive ASA plastic cover • Sealed sound unit with stainless steel diaphragm • Mounts in same hole pattern as the 6-11054 horn • Dimensions (L x W x H): 111mm (4.375") x 86mm (3.375") x 50mm (2") • Maximum amp draw: 3A, 12V • dB(A) rating: 106 at 1m (3') • Fundamental frequency: 440±20Hz Part No. 6-11050 (White) Part No. 6-11052 (Black) MINI COMPACT ELECTRIC HORN (12V) MINI TWIN ELECTRIC HORN (12V) COMPACT SINGLE HORN INTERNATIONAL WITH BLACK COVER (12V) SHORTY HORN (12V) • Totally sealed sound unit • Type 304 stainless steel cover, diaphragm, mounting bracket • Dimensions (L x W x H): 76mm (3") x 82mm (3.25") x 44mm (1.75") • Maximum amp draw: 3A, 12V • dB(A) rating: 106 at one meter • Fundamental frequency: 440±20Hz Part No. 6-11054 • Type 304 stainless steel covers, diaphragms, and mounting bracket • Dimensions (L x W x H): 76mm (3") x 203mm (8") x 44mm (1.75") • Maximum amp draw: 6A, 12V • dB(A) rating: 109 at one meter • Fundamental frequency: 490±20/440±20Hz Part No. 6-11056 • Stainless steel diaphragm and mounting bracket • Black polypropylene cover • Dimensions (L x W x H): 114mm (4.5") x 101mm (4") x 76mm (3") • Maximum amp draw: 4A, 12V • dB(A) rating: 108 at one meter • Fundamental frequency: 350±15Hz Part No. 6-11058 • Stainless steel diaphragm and mounting bracket • ABS, triple chrome-plated housing • Dimensions (L x W x H): 108mm (4.25") x 127mm (5") x 165mm (6.5") • Maximum amp draw: 4A, 12V • Fundamental frequency: 290±15 Hz • Loudest Marinco® compact electric horn • dB(A) rating: 123 at one meter Part No. 6-11060 For Marinco BEP Pro Installer Series, see pages 47-49 CATALOGUE SUPPLEMENT - H 25 Marinco AFI Wiper Kits & Motors GENERAL BOAT EQUIPMENT - WIPERS NEW RANGE WMW WIPER KIT (12V) Windshield Mount: 3/8" (9mm) shaft diameter KIT CONTENTS: • WMW Wiper Motor • 11.5" (292mm) Deluxe stainless steel curved blade (6-11311) • Deluxe adjustable 6.75" to 10.5" (171 266mm) stainless steel arm (6-11340) • Sweep: 80º • Shaft length: 2.5'' (63mm) Part No. 6-11200 WMW Wiper Motor Features: • Water-resistant sealed motor • Chrome-plated brass case and shaft housing • Stainless steel front plate and wiper shaft • Maximum current draw: 2 amps • Shaft diameter: 3/8" (9mm) • For external use in open cabin boats • Dimensions (L x W x D): 4.25" (108mm) x 2.75" (70mm) x 3.5" (89mm) STANDARD WIPER KIT (12V) Windshield Mount: 3/8" (9mm) shaft diameter KIT CONTENTS: • STD Wiper Motor • 11.5" (292mm) Deluxe stainless steel curved blade (6-11311) • Deluxe adjustable 6.75" to 10.5" (171 266mm) stainless steel arm (6-11340) • Sweep: 80º • Shaft Length: 2.5'' (63mm) Part No. 6-11204 STD Wiper Motor Features: • Corrosion-proof aluminium alloy case with black crackle finish • Base & mounting plates are chrome plated naval brass • Maximum current draw: 2 amps • 80° sweep, adjustable right or left self-parking • Shaft diameter: 3/8" (9mm) • Dimensions (L x W x D): 3.875" (98mm) x 2.25" (57mm) x 3.5" (89mm) 500 WIPER KIT (12V) Windshield Mount: 1/2" (13mm) shaft diameter • 500 Waterproof Wiper Motor (is totally sealed and 100% waterproof) • 11.5" (292mm) Deluxe stainless steel curved blade (6-11311) • Deluxe adjustable 6.75" to 10.5" (171 - 266mm) stainless steel arm (6-11340) • Sweep: 80º • Shaft Length: 2.5'' (63mm) Part No. 6-11210 MRV WIPER MOTOR • Easily powers 22" (559mm) x 22" (559mm) deluxe arm/blade combinations, or a 20" (508mm) x 20" (508mm) premier arm/blade combination at sweep sets of 80° or less • Factory pre-set sweep of 80º or 110º adjustable to 45º, 60º, 80º or 110º • 0.625" (16mm) diameter shaft • Available in 2 shaft lengths: 1.5" (38mm), 2.5" (63mm), *includes 0.5" (13mm) length of knurled arm fitting • Corrosion-resistant casing • Heavy-duty motor with right angle drive • Two-speed motor, can be operated as one speed • Solid brass knurled drive nut with brass and stainless steel drive shaft • Adjustable right or left self parking, coast to park • Includes 5 amp fuse and holder • Stainless steel fasteners and mounting bracket • Use with three-position switch (not included) • Compact size (L x W x D): 7.625" (193mm) x 4" Shaft* Voltage Sweep (101mm) x 2" (51mm) 1.5" (38mm) 12V 80° • Stall torque: 109 in-lbs (125 kgf/cm: 12.3 Nm) 2.5" (63mm) 12V 80° • Stall current: 11.5–13.0 amps 2.5" (63mm) 12V 110° • No load current: 0.5–1.2 amps 2.5" (63mm) 24V 110° 26 CATALOGUE SUPPLEMENT - H Part No. 6-11220 6-11224 6-11226 6-11227 Marinco AFI Wiper Kits & Motors GENERAL BOAT EQUIPMENT - WIPERS • Powers 16" (406mm) Deluxe arm and 16" (406mm) Deluxe blade combinations at a sweep set of 110° • Factory pre-set sweep of 80°, adjustable to 50°, 65°, 80°, or 110° • 0.625" (16mm) diameter shaft • Fully sealed waterproof housing made of UV stabilized, hightemperature, high-impact thermoplastic • 12 volt heavy-duty motor with anti-rotation drive shaft • Knurled drive shaft and solid brass arm drive nut • Coast to park with adjustable right or left self parking • Includes 5 amp fuse and holder (on/off switch not included) • RF shielded circuitry • Weight: 1.75 lbs (0.79kg) • Shaft length: 2.5" (68mm), *includes 0.5" (13mm) length of knurled arm fitting • Measures approximately (L x W x D): 6.625" (168mm) x 3.375" (86mm) x 2" (51mm) • Stall torque: 55 in-lbs (63 kgf/cm; 6.2 Nm) • Stall current: 9.8 - 10.0 amps 1000 WATERPROOF • No load current: 0.8 - 1.2 amps Kit Contents: Shaft* Voltage Sweep Part No. • 6-11244 motor 2.5" (63mm) 12V 80° 6-11244 • 6-11341 10'' - 14'' arm • 14'' polymer wiper blade NEW RANGE 1000 WATERPROOF WIPER MOTOR WIPER KIT Part No. 6-11248 2.5 WATERPROOF WIPER MOTOR • Fully sealed powder coated aluminium waterproof base and housing • Powers a 26" (660mm) Deluxe arm and Deluxe blade combination or a 24" (609mm) Premier arm and Premier blade combination • Shaft lengths: 1.5'' (38mm) or 2.5" (68mm), *includes 0.5" (13mm) length of knurled arm fitting • Factory pre-set sweep angles of 80°, with easy adjustment to 45° or 60° • Chrome plated solid brass knurled drive nut with brass and stainless steel drive shaft • Two speed motor • Sealed 6" wire leads, 16 AWG • Adjustable right or left self parking • 0.625" (16mm) diameter shaft • Coast to park • RF shielded circuitry • Includes 6 amp fuse and holder (operating switch not included) • Measures approximately (L x W x D): 7.875" (200mm) x 4.25" (108mm) x 3" (76mm) - see drawing • Stall torque: 139 in-lbs (160 kgf/cm; 15.7 Nm) • Stall current: 9.0 - 10.5 amps • No load current: 1.0 -1.6 amps Shaft* 1.5" (38mm) 2.5" (63mm) Voltage 12V 12V Sweep 80° 80° Part No. 6-11261 6-11264 CATALOGUE SUPPLEMENT - H 27 Marinco AFI Wiper Motor, Switch & Washer Kit GENERAL BOAT EQUIPMENT - WIPERS NEW RANGE 1.5 WATERPROOF WIPER MOTOR • Fully sealed powder coated aluminium waterproof base and housing • Powers a 22" (559mm) Deluxe arm and 22" (559mm) Deluxe blade combination or a 20" (508mm) Premier arm and 20" (508mm) Premier blade combination • Shaft length: 1.5'' (38mm) or 2.5" (68mm) (includes 0.5" (13mm) length of knurled arm fitting) • Factory pre-set sweep angles of 80°, with easy adjustment to 45° or 60° • Chrome plated solid brass knurled drive nut with brass and stainless steel drive shaft • Two speed motor • Sealed 6" wire leads, 16 AWG • Adjustable right or left self parking • 0.625" (16mm) diameter shaft • Coast to park • RF shielded circuitry • Includes 5 amp fuse and holder (operating switch not included) • Measures approximately (L x W x D): 7.75" (197mm) x 4" (101mm) x 2.75" (70mm) - see drawing • Stall torque: 109 in-lbs (125 kgf/cm; 12.3 Nm) • Stall current: 11.5 - 13.0 amps • No load current: 0.5 - 1.2 amps • Replaces AFI 2000 motor Shaft 1.5" (38mm) 2.5" (63mm) Voltage Sweep 12V 80° 12V 80° Part No. 6-11273 6-11274 INTELLIGENT WIPER SWITCH - SINGLE MOTOR AFI’s new microcontroller based “intelligent” switch provides all necessary wiper motor functions in one small component. • Settings for two continuous speed functions and three intermittent speed functions (2 second delay, 4 second delay, 8 second delay) • Washer system operation function • Blinking LED lights in switch indicate operating function • Dual motor switch synchronizes both motors in each mode and deactivates each motor individually • Works with 12V or 24V DC motors • Fits standard switch size openings, requires 2.65" (67.5mm) depth • Includes one ten pole connector with female pins and two female quick-connects ADD-ON WINDSHIELD WASHER KIT • Can be used on new or existing AFI™ Deluxe wiper arm and blade sets • Kit includes parts to outfit two wiper arms • Sprayer fittings (kit includes two) each have four adjustable brass nozzles to provide maximum spray coverage for most any windshield • Plastic parts are numbered to make installation easy Part No. 6-11292 28 KIT INCLUDES: • Water tank with mounting bracket • 12 Volt pump motor • Under deck tee fitting • Thru deck fitting and hardware • Below deck clear tubing (16 ft.) • Above deck black tubing (6 ft.) • Large and small rivet clips • Wiper arm clips • Sprayer fittings with clamps CATALOGUE SUPPLEMENT - H Part No. 6-11290 Marinco AFI Wiper Blades & Arms GENERAL BOAT EQUIPMENT - WIPERS NEW RANGE DELUXE ADJUSTABLE WIPER ARM • All arms are stainless steel • Arm has “articulating/bend-back” feature • Motor shaft mounting has additional set screw clamping Wet / Dry Dry Dry Dry Dry Length (adjustable) 6.75'' - 10.5'' (171 - 267mm) 10'' - 14'' (254 - 355mm) 14'' - 20'' (355 - 508mm) 18'' - 24' (457 - 609mm) Stainless Part No. 6-11340 6-11341 6-11342 – Black Part No. – 6-11345 6-11346 6-11347 DELUXE STAINLESS STEEL CURVED WIPER BLADES • Works well on curved or flat windshields POLYMER WIPER BLADES DELUXE ADJUSTABLE PANTOGRAPHIC ARM • For Use with AFI™ 2.5, 1.5 and MRV Motors • Stainless steel • Arm has “articulating/bend-back” feature • Motor shaft mounting has additional set screw clamping Wet / Dry Dry Dry Length (adjustable) 12'' - 17'' (305 - 432mm) 17'' - 22' (432 - 559mm) Stainless Part No. 6-11350 6-11351 PREMIER PANTOGRAPHIC S/S WIPER ARM • Combines the heavy-duty construction and materials of the Premier wiper arm line with a built-in wet arm system that allows for a clean and easy installation of a washer system • A simple and easy way to keep your windshield clean, the Premier wet arms feature a black PVC hose that runs up the center of the arm and ends in a four-nozzle fixture that is an integral part of the wiper arm itself • Each solid brass nozzle is adjustable to provide a maximum coverage spray pattern for most any windshield • Black glass polyimpregnated construction • Marine-grade rubber squeegee Length 11.5" (292mm) 14" (355mm) 16" (406mm) 18" (457mm) 20" (508mm) Part No. 6-11311 6-11312 6-11313 6-11314 6-11315 Length 12" (305mm) 14" (355mm) 16" (406mm) 18" (457mm) 20" (508mm) 22" (559mm) 24" (609mm) Part No. 6-11301 6-11302 6-11303 6-11304 6-11305 6-11306 6-11307 PREMIER S/S WIPER BLADE • All stainless steel construction Length Part No. • Marine grade silicone squeegee 20" (508mm) 6-11321 • Extra squeegee “claws” spread pressure evenly over the length of the blade, allowing the blade to conform to a curved windshield For more Marinco products see Section 8 of our catalogue. Pantographic wiper arms will only function properly with wiper motor sweep angles 80º or less. Wet / Dry Wet Length (adjustable) 17'' - 22'' (432 - 559mm) Stainless Part No. 6-11370 CATALOGUE SUPPLEMENT - H 29 International Boat Care Products NEW RANGE BOAT CONSUMABLES UV WAX SEALER NEW Boat Care products from SUPER CLEANER • High Strength Formula • Removes dirt, oil, wax and grease • Low odour • Cleans and degrease without damaging gelcoat or paint • Does not leave any residue • Biodegradable • Leaves GRP and painted surfaces ready to be restored Part No. 5-60950 (500ml) BOAT SHAMPOO • Mild universal cleaner useful for cleaning throughout the boating season but won’t damage wax protection • Hydrophobic – repels water • Free from silicon oils • Mixable with sea water & fresh water • Biodegradable Part No. 5-60951 (500ml) STAIN REMOVER • High-strength GRP cleaning gel • Easy to use • Penetrating gel quickly dissolves stains and marks on GRP areas like waterline or exhaust pipe stains • Removes surface rust on metal and gelcoat • Contains surfactant that dissolves oil and proteins • Does not damage adjacent surfaces • Will not run on vertical surfaces • No abrasives • No scrubbing required Part No. 5-60952 (500ml) LIQUID RUBBING • Coarse grain size – suitable for painted surfaces and GRP in poor condition • Safely removes marks and yellowing, and restores gloss • Restore the gelcoat’s original lustre • May be used in direct sunshine • Does no contain wax & silicone oils • Manual or machine use (800-1000 rpm) Part No. 5-60953 (500ml) MARINE POLISH • Fine graded liquid polish for a high gloss, smooth, reflective surface • Contains no silicon oils • Mild odour • Manual or machine use (800-1000 rpm) Part No. 5-60954 (500ml) MARINE WAX • Protective wax for GRP and paintwork • Provides excellent protection for polished surfaces • No abrasives or silicon oils • Easy to work & apply on large areas • Manual or machine use (800-1000 rpm) Part No. 5-60955 (500ml) POLISH AND WAX • All in one medium grade polish and wax formula • A quick and easy solution which saves time and effort • Contains a protective wax for long-lasting gloss • Safe for use on gelcoat and painted surfaces • Manual or machine use (800-1000 rpm) Part No. 5-60956 (500ml) • UV absorbing reactive wax, sealing the surface for ultimate gloss protection • Protects polished surfaces against the elements, dirt and oil • Hydrophobic – repels water. Also repels oil and dirt • Easy to use • Excellent UV protection • Manual or machine use (800-1000 rpm) Part No. 5-60957 (500ml) TEAK RESTORER • Cleans, restores and brightens teak and other hardwoods back to their original colour • Does not damage GRP, varnish, paintwork or aluminium • Can be used in conjunction with seawater or freshwater • For use on any teak or hardwood Part No. 5-60958 (500ml) TEAK OIL • Penetrating hardwood oil which protects and enhances the natural beauty of teak • Contains a rust inhibitor for metal surfaces • Penetrates even moist wood • Produces a protective and easy-clean surface • For use on any teak or hardwood Part No. 5-60959 (500ml) INTERNATIONAL MARINEFILM Instant Scratch Repair for Gelcoat & Paint Minor scratches are practically unavoidable. Yet we all know how much even the smallest scratch can be annoying. That's why MarineFilm puts a unique smart and easy do-it-yourself solution into the hands of all boat owners. Coated with high quality paint, it covers minor scratches with an ultra-thin adhesive film, instantly covering unsightly scratches in gelcoat or paint above the waterline. MarineFilm is easy to apply and offered in the twelve most popular gelcoat and International Paint topside paint colours. It’s cost-effective, kind to the environment and it provides strong season long adhesion whilst being easily removable when the boat is next hauled where it can be permanently repaired. 30 CATALOGUE SUPPLEMENT - H • Easy to apply, meaning a pleasing finish can be achieved quickly and unsightly scratches can be hidden instantly and without fuss • Avoids the need for clean up and personal Part No. Description protective equipment during application 5-60970 White 011 • Easy to match popular marine gelcoats 5-60971 White 012 and paints 5-60972 White 013 • Provides a season long temporary repair 5-60973 White 014 that enables the aesthetics of the topside to 5-60974 White 015 be maintained until the boat is next hauled 5-60975 Black 111 • No hassle removing when time to 5-60976 Blue 211 permanently repair. 5-60977 Blue 212 • Ready to use right out of the package 5-60978 Blue 213 • Two pre-cut shapes 5-60979 Blue 214 • Custom fit to size of repair 5-60980 Green 311 5-60981 Red 411 International Paints & Cuprinol Bilgex BOAT CONSUMABLES NEW RANGE FOR PR0FESSIONAL USE ONLY MICRON WA PREMIUM ANTIFOULING Contains unique water activated matrix technology, combining powerful performance with very low VOC1 Unique to International Paint, Micron WA has been developed using novel paint technology - Water Activated Matrix - which provides outstanding protection against all types of fouling in all types of water, including high-challenge areas, for up to 24 months.* • Longer in-service periods improve flexibility of maintenance schedules • Once activated, Water Activated Matrix technology delivers a crisp, vibrant colour and uniform appearance to provide a striking, attractive finish. • It also helps to reduce environmental impact by having optimised copper levels, using fewer natural resources and minimising the amount of VOCs emitted to the Practical Coverage (m²/Lt): 3.66 (Airless Spray), atmosphere that form ground level ozone (smog) which is 8.3 (Brush/Roller) harmful to humans, animals, vegetation and marine life. No. of coats: 2 - 3 • The extremely low VOC (~5 g/l) also helps with local VOC Substrates: GRP, Lead, Steel, Wood, Cast Iron regulation compliance. Application: Brush, Roller, Airless Spray • For all suitably primed substrates except aluminium Rated “Outstanding” on high fouling areas. • One pack product in a 5 Litre tin Colour Pre-Immersion Colour Post-Immersion * Depends on the total DFT (dry film thickness) applied. For 24 months performance, a total dry film thickness of 120µm (microns) needs to be achieved. Extra coats are needed if vessels are expected to operate at speeds in excess of 15 knots for extended periods. Black Blue Navy Water Activated Matrix Technology The unique Water Activated Matrix consists of a densely packed, structured arrangement of biocides, colouring pigment and voids. The antifouling appears matt when first applied, with colour variations or unevenness caused by different rates of water evaporation. However, on immersion, water enters the voids and filters through the matrix, saturating the pigments and developing the bright, crisp colour of the paint whilst, at the same time, efficiently releasing the active ingredients to deliver powerful antifouling performance. Patent Pending Colour Black Blue Navy Red Dover White Red Part No. 5-60094 5-60095 5-60096 5-60097 5-60098 Dover White The printing processes used in producing the colour charts do not allow exact colour reproduction and we recommend that you should check for accuracy before applying. International Paints colour charts are available. Micron WA - Outstanding Multi Season Protection* • Haul, wash and re-launch without re-painting every season • Extended in-service periods so owners and captains save money by the boat remaining in the water for longer • Improved flexibility of maintenance schedules with the option to apply more coats for more than 24 months performance NEW A panel test conducted in Malaga, Spain examined five different antifouling paints. Sample 3 with Micron WA shows very little slime after immersion for 26 months, in comparison to many of the others which display a significantly higher level of slime and fouling. CUPRINOL BILGEX Clears Grease, Scum & Oil • Emulsifies petrol, oil and grease in the bilge • Removes grease, scum and floating oil with the normal movement of the boat • Biodegradable • Highly concentrated - a little goes a long way • Gets rid of bad smells • Non-caustic; harmless to paintwork and fittings when diluted INTERNATIONAL INTERTUF 203 A one pack, tar free vinyl anticorrosive which can be used at temperatures down to -5°C (23°F). 20 Litre tin. Part No. 5-60893 1 Litre Bottle Part No. 5-27030 5 Litre Bottle Part No. 5-27031 CATALOGUE SUPPLEMENT - H 31 Polymarine Inflatable Boat & Rib Care NEW RANGE BOAT CONSUMABLES HYPALON FABRIC PVC FABRIC Hypalon inflatable boat material for repairing damaged tubes & floors. Hypalon is a synthetic rubber material patented by DuPont. Hypalon has many applications in many industries and it has proven itself as a material with excellent air holding capabilities and oil resistance. Hypalon coated onto polyester or nylon fabric with an interior coating of neoprene is a very reliable and durable inflatable boat fabric and can last for more than a decade even in the harshest environments. PVC inflatable boat material for repairing damaged tubes & floors. PVC is a vinyl polymer chemically known as polyvinyl chloride. In the inflatable boat industry it is used as a coating on polyester or nylon to increase the strength and tear resistance. Because it is a type of plastic, it can be thermobonded or glued. This allows the manufacturer to mass produce boats on a large scale with machines and unskilled labour. Half roll (70cm x 15cm) Half roll (70cm x 15cm) Colour Black Blue Grey Light Grey Orange Red White Yellow Full roll (145cm x 15cm) Colour Black Blue Grey Light Grey Orange Red White Yellow Part No. 5-81050 5-81051 5-81052 5-81053 5-81054 5-81055 5-81056 5-81057 Colour Black Blue Grey Orange Red White Part No. 5-81060 5-81061 5-81062 5-81064 5-81065 5-81066 Full roll (145cm x 15cm) Colour Black Blue Grey Orange Red White Part No. 5-81070 5-81071 5-81072 5-81074 5-81075 5-81076 For advice on selecting the correct fabric go to: www.polymarine.com 2990 HYPALON ADHESIVE Inflatable Boat Adhesive. 3026 PVC ADHESIVE Inflatable Boat Adhesive. Solvent based polychloroprene rubber glue giving high strength bonds, particularly suitable for emergency repair of inflatable boats, RIBs and Dinghies. Will bond natural rubber, polychloroprene, butyl, nitrile , hypalon and polyurethane rubber materials, leather. Solvent based polyurethane adhesive giving excellent adhesion to both plasticised and unplasticised PVC nylon fabric, polyurethane fabric and foam. Use for repair of all PVC inflatables including Zodiac/Bombard "Dynalon" and "Strongon" fabrics and Narwhal/Valiant "Hypertex". PLEASE NOTE :- For a complete bond 2903 solvent (Part No. 5-81125 or 5-81126), must be used before the adhesive is applied. Hypalon 1 Part Adhesive • Excellent resistance to heat, salt water and humidity • Easy to use as a single part glue for quick and temporary repairs • Cleaner - P510 Hypalon Solvent (Part No. 5-81120 or 5-81121) 70ml - Part No. 5-81101 5-81101 5-81103 5-81104 32 Part No. 5-81040 5-81041 5-81042 5-81043 5-81044 5-81045 5-81046 5-81047 PVC 1 Part Adhesive • Easy to use as a single part glue for quick and temporary repairs • Contact bonds in 10-15 minutes, full cure 48 hours 70ml - Part No. 5-81111 PVC 2 Part Adhesive • Easy to mix two part system supplied in sets with requisite amount of curing agent; can be used as a single part for quick temporary repairs • Contact bonds in 10-15 minutes, full cure 48 hours • Coverage - using 2 coats, 1 litre bonds 1 square metre • Easy to apply by brush, roller or serrated trowel Hypalon 2 Part Adhesive As above, plus: • Easy to mix two part system supplied in sets with requisite amount of curing agent; can be used as a single part for quick temporary repairs • Contact bonds in 10-15 minutes, full cure 48 hours • Coverage - using 2 coats, 1 litre bonds 1 square metre • Easy to apply by brush or roller 250ml Tin & Curing Agent Part No. 5-81103 250ml Tin & Curing Agent Part No. 5-81113 1 Litre Tin & Curing Agent Part No. 5-81104 1 Litre Tin & Curing Agent Part No. 5-81114 CATALOGUE SUPPLEMENT - H ! DO NOT USE HYPALON PRODUCTS ON ANY PVC COATED FABRIC SURFACE. Polymarine Inflatable Boat & Rib Care BOAT CONSUMABLES HYPALON EMERGENCY BOAT REPAIR KIT Please Note:- For a permanent repair, Polymarine 2 part adhesive must be used. Colour Black Blue Grey Light Grey Orange Red White Yellow Part No. 5-81000 5-81001 5-81002 5-81003 5-81004 5-81005 5-81006 5-81007 Contains: 70ml tube of PVC adhesive, 35 x 15cm of PVC material and instructions. Colour Black Grey Orange Red White Part No. 5-81020 5-81022 5-81024 5-81025 5-81026 Please Note:- For a permanent repair, Polymarine 2 part adhesive must be used. P510 HYPALON SOLVENT PRIMER 2903 PVC SOLVENT PRIMER & CLEANER • For degreasing hypalon surfaces before adhering and cleaning brushes. • Suitable for reactivating applied adhesive 500ml Part No. 5-81120 1 Litre Part No. 5-81121 • A primer to degrease and prepare PVC surfaces before adhering • Suitable for reactivating applied adhesive and cleaning brushes 500ml Part No. 5-81125 1 Litre Part No. 5-81126 FLEXITHANE HYPALON PAINT SUPERFLEX PVC PAINT A fully flexible paint formulated for Hypalon PU and rubber variant fabric • Smooth satin finish, will not crack or flake off • No mixing required, apply with a brush or gloss roller, touch dry in 30 minutes. Can be sprayed • Two coats for best results • Used for resealing and preventing rubbing strake and mouldings from powdering Colour • Coverage 3 sq m per 500ml Black WARNING - Flexithane must not Blue be used on any PVC coated Grey fabric surface. Orange Red For paint colours see page 34 White A fully flexible paint formulated for renovating PVC and any other PVC variant fabric • Smooth satin finish, will not crack or flake off • No mixing required, apply with a brush or gloss roller, touch dry in one hour • Seawater and sunlight resistant • Many uses including hatch covers, PVC fenders, boatcovers, dodgers etc. Colour • Coverage 2.5 sq m per 500ml Black Blue Grey Orange Red White Yellow Midnight Blue Size 500ml 500ml 500ml 500ml 500ml 500ml Part No. 5-81210 5-81211 5-81212 5-81214 5-81215 5-81216 LIQUID LETTERS HYPALON LETTERING PAINT A fully flexible paint formulated for Hypalon PU and rubber variant fabric • Smooth satin finish, will not crack or flake off • No mixing required, apply with a brush or gloss roller, touch dry in 30 minutes. Can be sprayed • Two coats for best results • Used for resealing and preventing rubbing strake and mouldings from powdering Colour WARNING - Must not be used on Black any PVC coated fabric surface. Blue Grey For paint colours see page 34 Orange Red White ! NEW RANGE PVC EMERGENCY BOAT REPAIR KIT Contains: 70ml tube of Hypalon adhesive, 35 x 15cm of Hypalon material, abrasive paper and instructions. Size 500ml 500ml 500ml 500ml 500ml 500ml 500ml 500ml Part No. 5-81230 5-81231 5-81232 5-81234 5-81235 5-81236 5-81237 5-81238 For paint colours see page 34 LETTERFLEX PVC LETTERING PAINT Size 125ml 125ml 125ml 125ml 125ml 125ml Part No. 5-81200 5-81201 5-81202 5-81204 5-81205 5-81206 DO NOT USE HYPALON PRODUCTS ON ANY PVC COATED FABRIC SURFACE. Tin A fully flexible paint formulated for Colour renovating PVC and any other PVC Black variant fabric Blue • Smooth satin finish, will not crack or Orange flake off Red • No mixing required, apply with brush White or gloss roller, touch dry in 1 hour Yellow • Seawater and sunlight resistant Aerosol • Many uses including hatch covers, Colour PVC fenders, boatcovers, Orange dodgers etc. Red • Can be used with our cut stencils White Size 125ml 125ml 125ml 125ml 125ml 125ml Part No. 5-81220 5-81221 5-81224 5-81225 5-81226 5-81227 Size 150ml 150ml 150ml Part No. 5-81244 5-81245 5-81246 CATALOGUE SUPPLEMENT - H 33 Polymarine Inflatable Boat & Rib Care NEW RANGE BOAT CONSUMABLES SP54 HYPALON ANTIFOUL SP54 PVC ANTIFOUL Fully flexible antifoul for use on Hypalon material. Can also be used on non-flexible surfaces such as GRP. • Hull and tubes can be protected on your RiB with just one product. • Developed using unique pseudo-organic technology • Extensively tested - keeps virtually Colour Black all hulls free from growth of algae, Blue crustaceans and othe unwelcome Grey marine life Orange • Includes copper White A fully flexible antifoul for use on PVC material. Can also be used on non-flexible surfaces such as GRP. • Hull and tubes can be protected on your RiB with just one product. • Developed using unique pseudo-organic technology • Extensively tested - keeps virtually Colour all hulls free from growth of algae, Black crustaceans and othe unwelcome Grey marine life Red • Includes copper White Polymarine Paint Colours Black Blue Part No. 5-81270 5-81271 5-81272 5-81274 5-81276 Size 1 Litre 1 Litre 1 Litre 1 Litre Part No. 5-81280 5-81282 5-81285 5-81286 The printing processes used in producing the colour charts do not allow exact colour reproduction and we recommend that you should check for accuracy before applying. Grey Orange Red White Yellow Midnight Blue DISPEL STAIN & RUST REMOVER AQUA STOP SEALFLEX SEALANT Removes rust stains, organic stains, algae stains from fibre glass. • Easy to use, non abrasive gel • For those difficult to remove yellow and rust stains on GRP • Simply brush onto contaminated area and leave. Once gel has turned to powder, either wipe or rinse with clean water & watch stain disappear 500ml Part No. 5-81300 Flexible waterbased acrylic latex sealant used internally for sealing porosity and minor leaks in Hypalon & PVC inflatables • Sealflex is introduced into the inflatable through the valve, which is then inflated and tumbled to circulate the sealant which adheres & cures to form an impermeable membrane • Suitable for painting on the inside of seams during manufacture • Sufficient for an 8-9ft inflatable • Improved formula flows & seals the tube more efficiently 500ml Part No. 5-81305 INFLATABLE BOAT CLEANER An easy to use cleaner specifically formulated for use on inflatable boats • Suitable for both PVC and Hypalon fabrics • Removes dirt, white oxidation, grease, oil and petrol deposits • Biodegradable 500ml Part No. 5-81310 34 Size 1 Litre 1 Litre 1 Litre 1 Litre 1 Litre Protect your electrical equipment from water/moisture ingress • Formulated to protect all low voltage equipment eg. VHF radios, GPS, etc. • One application provides permanent protection 200ml Aerosol Part No. 5-81302 INFLATABLE BOAT FINISH A finishing product specifically for use on inflatable boats • Suitable for both PVC & Hypalon fabrics • Easy to apply with a soft cloth, no polishing required, dries to a pleasant sheen • Helps to prevent resoiling • Contains no silicones or distillates 250ml Part No. 5-81314 INFLATABLE BOAT GRP SILICON FREE POLISH • Wipe on – Polish – Wipe off • Gently buffs and polishes to a brilliant shine without scratching • Totally safe on all marine materials • Silicon Free formulation 250ml Part No. 5-81316 RIB VALETING KIT FLUSH FIT VALVES Supplied in a draw string PVC bag with blue fabric top, comes complete with two Inflatable Boat Cleaners, one Inflatable Boat Finish, one GRP Silcon Free Polish, two Polishing Cloths, one Sponge, one Trigger Spray and a pair of disposable gloves. Everything that you need to keep your Rib looking good. Part No. 5-81320 • Acetal flush fitting complete inflate/deflate valve • Mechanically fitted into hole 38mm dia. with reinforcing fabric doubler required depending on pressure. No Handle Pull Handle • Servicing is kept to a minimum. Colour Pull Handle Part No. • Overall Dia: 65mm Black No 5-81150 • Height: 43mm Grey No 5-81151 • Baynet fit cap. Black Yes 5-81152 • Push and turn core to deflate Grey Yes 5-81153 CATALOGUE SUPPLEMENT - H Weaver Snap Davits GENERAL BOAT EQUIPMENT A set of ingenious lock-on davit fittings to secure an inflatable boat or RIB tender to the swim platform or transom of the main vessel. For tenders up to 60kg (140lbs) in weight. Two davit fittings are bolted onto the swim platform or transom of the main vessel, the rubber pads and hooks are attached to the tender, and these then clip into a locked position on each davit head, allowing the tender to be secured and tilted into a vertical position. • Safely board/alight your tender • Strong & Robust dinghy Pads • Reduced mooring fees in marinas • Easy snap-on action to lock • Little force required to release RBD100 SNAP DAVIT - SWIMBOARD FIT RBD150 SNAP DAVIT - TRANSOM MOUNT Suitable for tenders up to 60kg (140lbs) in weight. Complete boxed kit contains: • 2x S/S Snap Davit fittings screws/nuts/washers required for fixing • 2x large grey rubber pads • 2x stainless steel hooks Part No. 6-38101 Suitable for tenders up to 60kg (140lbs) in weight. Complete boxed kit contains: • 2x S/S Snap Davit fittings screws/nuts/washers required for fixing • 2x large grey rubber pads • 2x stainless steel hooks Part No. 6-38110 RBD100 KIT WITH 2", 4" EXTENDED OR OFFSET DAVIT HEADS QUICK RELEASE SHOE FOR RBD 100 SNAP DAVIT 2" or 4" extended head, or 4" out 4" down offset davit head for curved swim platform. Boxed kit for boats with a swim platform comprises: • 2x RP101 Pads (for attachment to the inflatable or RIB tender) • 2x RSH 120 Hooks • 2x extended or offset head swim platform mount Snap Davits Description 2'' RBD100 Extended 4'' RBD100 Extended 4'' x 4'' RBD100 Offset NEW RANGE WEAVER SNAP DAVITS FROM POLYMARINE Part No. 6-38112 6-38114 6-38119 Pair of Stainless Steel shoes for RBD 100 kits for quick removal of davit heads. Supplied with stainless steel fixing bolts and quick release pin. The 'quick fit' allows for quick removal of the davit heads so bathers don't stub their toes or trip over the davit heads. Allows unhindered access to the bathing platform. The shoes are bolted down to your swim platform. By releasing the pin the davit Part No. 6-38150 head can be quickly and easily removed. Stand-off Arms & Securing Pads Stainless steel bracket arms secure the tender in a raised position on davits. Fixed by a bracket to the yacht transom at its highest point when the tender is raised to 90 deg, and to a special moulded pad adhered to the upper part of the tender when raised. Provides security when underway and removes strain on the davit fittings in keeping the tender at 90 deg. Arms Supplied in Pairs / Pad in Singles STAND OFF ARMS Supplied in pairs as a kit with 2x arms and 4x 'L' shaped brackets for mounting. Fixed onto the tender with one arm secured with an 'L' shaped bracket to the edge of the transom at its highest Size Part No. point when the tender is raised to 90º on its davits, 12'' x Pair 6-38161 and the second arm to a special moulded pad 18'' x Pair 6-38162 which is adhered to the upper part of the tender 24'' x Pair 6-38163 when raised, (order pads separately). 30'' x Pair 6-38164 For a rigid tender two 'L' shape bracket fixings 36'' x Pair 6-38165 can be used. RP101 LARGE RUBBER PAD FOR RBD100/150 RSH120 HOOKS FOR RP101 PAD Replacement neoprene pad for RBD kits • RSH 120 hook fits into the pad • To be bonded onto tube • Colour: Grey Part No. 6-38155 Replacement stainless steel hooks for neoprene pad for RBD kits • Supplied as a pair • Supplied with S/S fixing bolts • To fit into RP101 pad Part No. 6-38156 RUBBER PAD FOR STAND-OFF ARMS TOGGLES FASTNERS FOR DAVIT HEADS Designed for attaching stand-off brackets to the tube/inflatable. Two can be used on a soft tail dinghy. Pad is bonded on using adhesive. Colour: Grey. Part No. 6-38168 The Toggler is placed through a pre-drilled hole and the stainless steel plate expands out. Insert the bolt and your davit head is attached. No more stripping inside to get to the nuts. Part No. 6-38152 CATALOGUE SUPPLEMENT - H 35 Loctite Sealants & Adhesives NEW RANGE BOAT CONSUMABLES - SEALANTS & ADHESIVES LOCTITE 243 LOCK ‘N SEAL 24ml LOCTITE 270 STUD ‘N BEARING FIT 24ml Loctite 243 medium strength threadlocker, suitable for all metal threaded assemblies. Breakaway torque 26Nm. • Works on all metals, including passive substrates (e.g. stainless steel, aluminium, plated surfaces) • Proven to tolerate slight contaminations of industrial oils, e.g. engine oils, corrosion prevention oils and cutting fluids • Prevents loosening on vibrating parts, e.g. pumps, gear boxes or presses • Permits disassembly with hand tools for servicing • P1 NSF Reg. No.: 123000 Loctite 270 High Strength, general purpose threadlocker. Breakaway torque 33Nm. • Suitable for all metal fasteners, including stainless steel, aluminium, plated surfaces and chrome-free coatings • Tolerates slight contaminations of industrial oils, e.g. engine oils, corrosion prevention oils, cutting fluids • Ideal for permanently locking studs on engine blocks and pump housings • To be used if regular removal for maintenance is not required • P1 NSF Reg. No.: 123006 Part No. 5-21141 (Qty 12) Part No. 5-21141/1 (Single) Part No. 5-21142 (Qty 12) Part No. 5-21142/1 (Single) Specification Maximum thread size: Strength: Breakaway torque: Fixture time steel: Fixture time brass: Fixture time stainless steel: Service temperature range: M36 Medium M10 bolts: 26 Nm 10 min. 5 min. 10 min. -55 °C to +180 °C Specification Maximum thread size: Strength: Breakaway torque: Fixture time steel: Fixture time brass: Fixture time stainless steel: Service temperature range: Up to M20 High M10 bolts: 33 Nm 10 min. 10 min. 150 min. -55 °C to +180 °C LOCTITE 55 PIPE SEALING CORD 50m Pot LOCTITE 2701 THREADLOCKER 50ml Loctite 2701 High strength threadlocker, especially for chromated surfaces Part No. 5-21144 (Single) Specification Maximum thread size: Strength: Breakaway torque: Fixture time steel: Fixture time brass: Fixture time stainless steel: Service temperature range: Up to M20 High M10 bolts: 38 Nm 10 min. 4 min. 25 min. -55 °C to +150 °C Specification Maximum pipe size: Disassembly strength: Service temperature range: Breakaway torque: 4" Low -55°C - +149°C n.a. LOCTITE SI 5980 QUICK GASKET LOCTITE SI 5990 QUICK GASKET 40ml General Purpose Flange Sealant 40ml High Temperature Flange Sealant Premium high performance silicone black for flanges exposed to permanent oil contact. • Excellent oil resistance • For all kind of flanges including metals and plastics as well as combinations of both • Can replace pre-cut paper or cork gaskets • High flexible gasket maker • Non-corrosive • Health & Safety friendly Premium high performance silicone copper for flanges exposed to high temperatures (up to 300ºC). • Excellent temperature resistance • For all kind of flanges including metals and plastics as well as combinations of both • Can replace pre-cut paper or cork gaskets • Non corrosive • Health & Safety friendly Part No. 5-21162 (Qty 12) Part No. 5-21162/1 (Single) Part No. 5-21160 (Qty 12) Part No. 5-21160/1 (Single) Specification Colour: Tack free time: Tensile strength: Service temperature range: 36 Loctite 55 pipe & threadsealing cord. • General purpose, threaded pipe and fitting sealant • Non curing, immediate, full pressure seal • For a quick, easy and reliable seal • WRC listed, meets BS 6920 for potable water: 0808533 • DVGW/KTW approval for gas and potable water • Tested in accordance with EN 751-2 Class ARp and DIN 30660 • Certified to NSF/ANSI, Standard 61 Part No. 5-21155 (Qty 24) Part No. 5-21155/1 (Single) Black 30 min. 1.6 N/mm² -55°C to 250°C CATALOGUE SUPPLEMENT - H Specification Colour: Tack free time: Tensile strength: Service temperature range: Copper 40 min. 1.9 N/mm² -60°C to 350°C Sealants & Adhesives (Various) BOAT CONSUMABLES - SEALANTS & ADHESIVES LOCTITE 574 MULTI GASKET 40ml Multi purpose flexible silicone sealant. 50ml general purpose sealant for machined, rigid metal flanges. For flexible flanges, machined or casted surfaces. Can be used on metal, plastic and painted parts. Resists vibration, thermal expansion and contraction Ideal for use on rigid metal parts, e.g. cast iron components and pump housings Part No. 5-21168 (Single) Part No. 5-21166 (Qty 12) Part No. 5-21166/1 (Single) Specification Colour: Service temperature range: Max. gap: Skin over time: Cure through volume in 24 h: Strength: Cure method: NEW RANGE LOCTITE SI 5926 INSTANT GASKET Specification Colour: Service temperature range: Tensile shear strength: Max. gap: Fixture time steel: Fixture time aluminium: Strength: Cure method: Blue -60°C - +200°C 1mm 60 min. 2.5 mm Low Moisture (Silicone) Orange -50°C - +150°C 8.5N/mm² 0.25mm 15 min. 45 min. Medium Anaerobic LOCTITE 3463 MAGIC METAL STEEL STICK 114g Metal-filled Compounds, 2K Epoxy. Sets in 10 minutes. Steel filled kneadable stick. Adheres to damp surfaces and cures under water. Chemical and corrosion resistant. Can be drilled, filed and painted. • Emergency sealing of leaks in pipes and tanks • Smoothes welds • Repairs small cracks in castings Specification Working life: Fixture time: Shear strength (GBMS): Compressive strength: Service temperature range: Part No. 5-21170 (Single) GEOCEL® TRADE MATE SILICONE PLUMBA FLUE High Temperature Silicone Sealant CAPTAIN TOLLEY'S CREEPING CRACK CURE • One part water based acrylic co-polymer penetrating sealant • Seals hairline cracks by capillary action 24 hour curing time providing a clear, flexible and paintable seal • Can be used on wood, glass, rubber, metals, perspex, ceramic, fibreglass, polystyrene and some plastics • For use around the home, boat caravan, motorhome or car Size 60ml 60ml 250ml 250ml Qty 12 Each 12 Each Part No. 5-70100 5-70100/1 5-70101 5-70101/1 A one component, high temperature acetoxy silicone sealant suitable for use on nonporous surfaces and ideal for sealing gas flues. Once cured, Trade Mate Plumba Flue is able to withstand temperatures of up to 300ºC for short term exposure and 250ºC for long term exposure. Suitable for sealing gas flue and chimney terminals. 3 min. 10 min. >6 N/mm² 82.7 N/mm² -30 °C to +120 °C See Section 5 for Paints, Sealants & Consumables Bulk Pack: 12 x 310ml cartridges (Black): Part No. 5-70031 Single: 310ml cartridge (Black): Part No. 5-70031/1 FARÉCLA SPURRING BRUSH Spurring brush for manually cleaning excess compound from a pad. Part No. 5-21460 CATALOGUE SUPPLEMENT - H 37 Quicksilver Oils & Lubricants BOAT CONSUMABLES - OILS & LUBRICANTS NEW RANGE PREMIUM PLUS 2 STOKE TC-W3 OUTBOARD OIL PREMIUM 2 STOKE TC-W3 OUTBOARD OIL Specifically formulated with a marine additive package to meet the needs of low to mid-horsepower outboard engines. • For use in normal marine operating conditions • Exceeds TC-W3 standards • Reduces rust and corrosion of internal components • Provides enhanced detergency to help keep your engine free of deposits • Meets all outboard and personal watercraft manufacturers’ recommendations for use of TC-WII and TC-W3 oils in pre-mix or oil-injected models Size 1 Litre 4 Litre 10 Litre Qty 6 3 2 Part No. 5-38021 5-38022 5-38023 OPTIMAX/DFI 2 STOKE OUTBOARD OIL Specifically formulated and developed to meet the needs of all Direct Fuel Injected (DFI) 2-stroke outboard engines. • Specifically formulated to meet the unique performance demands of next generation two-stroke DFI engines • Incorporating a synthetic, high viscosity, lubricity additive to provide maximum scuff protection at the high operating temperatures associated with DFI engines • Enhanced detergency additives providing superior piston cleanliness to prevent ring sticking. • Formulated with improved rust protection for the unique demands of the marine environment. Size 4 Litre 10 Litre Part No. 5-38037 5-38038 Size 1 Litre 4 Litre 10 Litre Qty 6 3 2 Part No. 5-38026 5-38027 5-38028 HEAVY DUTY DIESEL ENGINE OIL 15W 40 Specifically formulated and developed to meet the needs of all marine diesel engines. • 15W-40 oil formulated to combat sludge and varnish formation • Contains a higher additive level than standard fleet oils, providing better protection • Provides excellent shear stability to assure stay-in-grade performance, even in highly stressed applications • Protects internal engine components from corrosion and wear • Provides excellent water tolerance. Size 4 Litre Qty 3 Part No. 5-38042 PERFORMANCE 4 STOKE OUTBOARD OIL 10W 30 STERNDRIVE & INBOARD 4 STOKE OIL 25W 40 Specifically formulated and developed to meet the needs of all 4-stroke outboard engines. • Developed for the rigours of the marine environment • Field-proven to provide superior lubrication as well as protection from corrosion and wear • Low-temperature viscosity formula allows for easy cold temperature starting • Shear stable additives prevent oil degradation. • Enhanced formula developed with heavy duty additives • Exceeds all 4-stroke outboard engine manufacturers’requirements and surpasses API service requirements for SJ, CF-2 and CH-4 Specifically formulated and developed to meet the needs of high-output sterndrive and inboard engines. • Multi-viscosity 25W-40 oil formulated to eliminate thermal breakdown (no viscosity improvers necessary) under extreme temperatures and loads • Field-tested & proven in petrol & diesel applications • Provides superior lubrication and protection of internal components from corrosion, wear, scuffing and scoring – even in higher temperature engines • Meets and exceeds API service requirements for SJ, CF-2, CH-4 with a multi-functional additive that assures “Marine Grade” oil performance. Size 1 Litre 4 Litre 38 Qty 3 2 Specifically formulated with a higher concentration marine additive package to meet the needs of high-horsepower outboards, including direct fuel-injected engines. • For use in extreme marine operating conditions • Far exceeds Mercury in-house test standards which are more stringent than the industry’s TC-W3® standard • Cleanest burning-reduces carbon build-up in exhaust system • Reduces smoke • Superior lubrication • Meets all outboard and personal watercraft manufacturers’recommendations for use of TC-W3 oils in pre-mix or oil-injected models Qty 6 3 Part No. 5-38045 5-38046 CATALOGUE SUPPLEMENT - H Size 1 Litre 4 Litre Qty 6 3 Part No. 5-38048 5-38049 DELIVERY Unable to send via carrier. Please contact your local Aquafax sales depot for delivery methods. Quicksilver Oils & Lubricants BOAT CONSUMABLES - OILS & LUBRICANTS Size 1 Litre 4 Litre Qty 6 3 Specifically formulated and developed to meet the needs of all 4-stroke marine engines. • Advanced protection not offered by conventional automotive oils • For use in all MerCruiser and other sterndrive engines • For use in all 4-stroke engines • Superior friction and wear protection • Industry-leading internal marine engine corrosion protection Part No. 5-38052 5-38053 Size 946ml 4 Litre SYNTHETIC BLEND 4 STROKE OUTBOARD OIL 25W 50 Formulated for pressure charged and intercooled engines and contains an advanced additive system that provides unmatched performance. • Industry leading corrosion protection • Enhanced protection against varnish build-up and sludge formation in critical engine parts • Improved lubricity benefits internal engine parts for extended reliability • Ideal for commercial and recreational use • Exceeds all outboard manufacturers’ oil requirements and FC-W® marine qualifications Size 4 Litre Qty 3 SYNTHETIC BLEND 4 STROKE STERNDRIVE AND INBOARD OIL 25W 40 Part No. 5-38084 Qty 6 3 Part No. 5-38055 5-38056 SYNTHETIC 4 STROKE CATALYST STERNDRIVE & INBOARD OIL 20W 40 Formulated to provide optimum operation and longer life for the critical engine catalyst systems that safeguard our environment. Catalysed marine engine use • Extended catalytic converter life due to low phosphorus formation Sterndrive and Inboard use • Three distinct synthetic base stocks provide superior wear protection and lubrication • Provides extreme salt water and freshwater rust protection • Reduced oil consumption, improved pumping ability • A more stable, high viscosity oil that prevents dirt and soot from settling on metal surfaces Size • Exceeds all outboard manufacturers’ oil 1 Litre requirements & FC-W® marine qualifictions 4 Litre PREMIUM GEAR OIL 80W 90 HIGH PERFORMANCE GEAR OIL SAE 90 Specifically designed and developed to meet the needs of outboard lower units. • Provides excellent lubrication and wear resistance for outboard lower unit gears • Great for both high and low horsepower engines under varying operating conditions • Special additives protect gears from metal-to-metal contact • Exclusive formulation helps improve film adhesion to gears. • Since no industry wide standards exist concerning marine gear oils, it is essential to use products such as this which has been specifically designed and tested for marine Size applications 237ml • Do not mix with High 1 Litre Performance Gear Oil 10 Litre Engineered to provide maximum protection for sterndrive and outboard lower units. • Exclusive formula provides extended gear life in extreme conditions including high-speed and high horsepower applications • Extensively tested to provide excellent protection against corrosion and excessive wear. • Specifically formulated to help prevent failures due to water entering the gear housing. • Extreme-pressure synthetic additives protect gears from metal to metal contact. • Since no industry-wide standards exist concerning marine gear oils, it is Size essential to use products such as this 237ml which has been specifically designed 1 Litre and tested for marine applications. 10 Litre • Do not mix with Premium Gear Oil. Qty 12 6 2 NEW RANGE SYNTHETIC BLEND 4 STROKE OUTBOARD OIL 25W 40 Specifically formulated and developed to meet the needs of all 4-stroke outboard engines. • Newly formulated to provide the highest level of performance and protection available today from a 4-stroke outboard oil • Recommended oil for use in Verado engines. • For use in all 4-stroke engines • First in class for all durability test properties • Industry-leading internal marine engine corrosion protection Part No. 5-38100 5-38102 5-38104 DELIVERY Unable to send via carrier. Please contact your local Aquafax sales depot for delivery methods. Qty 6 3 Part No. 5-38087 5-38088 Qty 12 6 2 Part No. 5-38110 5-38112 5-38114 CATALOGUE SUPPLEMENT - H 39 Quicksilver Oils & Lubricants NEW RANGE BOAT CONSUMABLES - OILS & LUBRICANTS QUICKARE FUEL TREATMENT OIL Quickare is a complete fuel treatment that can be used in all grades of gasoline, including ethanol blends. Use Quickare at every fill-up to: • Maximize engine performance with all grades of gasoline • Help control corrosion, gum and varnish build-up, and phase separation associated with ethanol-blended fuel • Help control moisture and corrosion problems associated with non-ethanol fuel • Clean up existing varnish and gum deposits from fuel lines, tanks, carburetors and injectors, intake valves, and spark plugs • Keep fuel fresh between fill-ups - up to 12 months Each 355ml bottle treats 227L Size 355ml Qty 12 Formulated to clean the injectors and restore original spray pattern - which helps prevent recurring problems, and reduces intake and port deposits. Clean fuel injectors mean cleaner running, more efficient engines and lower emissions. No mixing required - use right from the can. Part No. 5-38126 QUICKSTOR FUEL STABILIZER Quickleen is a deep cleaning treatment that should be used periodically. Aggressive cleaners work to quickly and thoroughly remove carbon deposits from carburetors and injectors, intake valves, spark plugs, piston crowns and cylinder heads. This product does not contain fuel stabilizers. Use with Quickare to prevent fuel breakdown and oxidation. Use Quickleen to: • Prevent engine knocking and piston seize-up • Extend spark plug life Add Quickstor to fuel before storing your engine to ensure your fuel is ready to go at the start of the next season. Use Quickstor to: • Prevent regular and ethanol-blended fuel from breaking down and oxidizing • Prevent fuel system corrosion • Prevent gum and varnish from forming in the fuel and settling in fuel lines and tanks, carburetors and injectors • Keep injectors and carburetor lubricated • Stabilize fuel for up to a year Each 355ml bottle treats 227L Each 355ml bottle treats 227L Qty 12 Part No. 5-38124 Size 355ml Qty 12 Part No. 5-38122 POWER TUNE ENGINE CLEANER STORAGE SEAL FOGGING OIL For use in all 2- and 4- stroke carbureted and fuel injected petrol engines. Assists in restoring lost power due to carbon, gum and varnish deposits that accumulate in the combustion chambers of petrol engines, as a result of normal engine use. Removing these deposits helps improve fuel/air flow and overall engine performance. Specially formulated compound for all 2- and 4- stoke engines that forms a protective barrier against rust on internal metal surfaces. To be used at the end of the season or whenever it will not be used for more than a month. Size 340g Qty 12 Part No. 5-38135 Size 340g 3.78L Qty 12 2 Part No. 5-38143 5-38145 HIGH PERFORMANCE EXTREME GREASE CORROSION GUARD AEROSOL • Calcium sulfonate-based NLGI grease • Excellent rust and corrosion protection • Formulated for high-temperature & high-load applications • 100% compatible with lithium-based greases For use in the following applications: steering systems/ cable linkages, throttle and shift cables, drive shaft splines, gimbal bearings, U-joints, suspension systems, chassis, ball joints, disc brakes and ABS applications, trailer wheel bearings. Corrosion Guard is a rust inhibitor that forms a water resistant barrier on non-painted and painted surfaces. Protects outdrives, lower units and power trim motors from rust. Remains clear and doesn’t peel. Can also be used to prevent further paint damage in areas where undercutting and blistering have occured. Do not spray on surfaces coated with antifouling or biocide paint. Size 227g 40 Qty 12 QUICKLEEN ENGINE & FUEL SYSTEM CLEANER Size 355ml Part No. 5-38120 FUEL INJECTOR CLEANER OTC® INJECT-R-KLEEN Size 473ml The Quicksilver Fuel Care System is one complete system - specially formulated by the people who made your engine, with decades of experience on all kinds of engines - to help it run its best. It's as easy as 1, 2, 3 - regardless of whether you use ethanol- or non-ethanol-blended fuels. Qty 12 Part No. 5-38141 Use Quicksilver grease gun (P/No. 5-38171) CATALOGUE SUPPLEMENT - H Size 312g Qty 6 Part No. 5-38147 DELIVERY Unable to send via carrier. Please contact your local Aquafax sales depot for delivery methods. Quicksilver Oils & Lubricants BOAT CONSUMABLES - OILS & LUBRICANTS Quicksilver 2-4-C marine grease is a multi-purpose lubricant that withstands extreme friction and won’t break down when mixed with water. Contains rust and oxidation inhibitors to prevent corrosion. Also contains PTFE for added friction reduction and reduced wear. Recommended uses: steering systems, cable linkages, throttle and shift cable and linkages, remote controls, prop shafts, swivel pins, drive shaft splines, tilt lock mechanisms, tilt tubes, hinge pins and trailer wheel bearings. Size 227g 3 x 85g 397g Qty 12 10 4 Part No. 5-38150 5-38152 5-38154 Use with Quicksilver tubes gun (5-38171) Quicksilver cartridge gun (5-38170) – POWER TRIM & STEERING FLUID • For use in power trim and steering systems • Unique formula helps prevent corrosion, oxidation and wear • Suitable for high temperature applications Size 237ml Qty 12 QUICKSILVER GREASE GUN QUICKSILVER GREASE GUN For 85g cartridge (5-38152). Part No. 5-38170 For 227g cartridge (5-38150). Part No. 5-38171 EXTENDED LIFE COOLANT ANTI-FREEZE MARINE ENGINE COOLANT • Ready to use premixed 50/50 formula (deionised water) • Ethylene glycol-based product • Will not cause gelling and provides superior corrosion protection • Protects all cooling system metals including aluminium • Silicate and Phosphate free • Provides anti-freeze protection to -36ºC (-34ºF) Low silicate formula specially recommended for four stroke diesel and petrol engines with closed cooling systems • Coolant additives provide protection against corrosion and scale formation • Ready to use premix formula requires no mixing or additives • Low silicate formula prevents silicate gelling which can restrict engine cooling passages and cause overheating • Provides antifreeze protection down to -36ºC (-33ºF) Size 3.78ml Qty 4 Part No. 5-38182 NEW RANGE 2-4-C MARINE LUBRICANT WITH PTFE Part No. 5-38160 Size 5 Litre Qty 2 Part No. 5-38185 For more Oils & Lubricants see Section 5 of our Catalogue DELIVERY Unable to send via carrier. Please contact your local Aquafax sales depot for delivery methods. CATALOGUE SUPPLEMENT - H 41 Ultraflex GoTech™ Steering System ULTRAFLEX STEERING GOTECH™- PACKAGED OUTBOARD STEERING SYSTEM FOR SINGLE ENGINE UP TO 115 HP • For outboard single engine up to 115 hp • Wheel turns 4,5 NEW 1 2 GOTECH™ package kit contains: UP18 Intermediate helm pump The wheel is UC81-OBF Front mount outboard cylinder not included. OL 150 Hydraulic oil – 2 litres. KIT OB-GT/M Hose kit dia. 1/4" 6m (19.7') length Part No. 4-48120 APPLICATION GUIDE FOR UC81-OBF 3 Engine KIT OB-GT/M - Hose Kit with Preassembled Fittings at One End for Single Station Application. Consists of a pair of high pressure flexible hose dia. 1⁄4 '' with fittings featuring turning nuts preassembled at one end only and supplied with 2 non assembled fittings. 6m (19.7') standard length that can be cut to fit the desired application. 1 Mercury® Mariner® Evinrude® 2 UP18 HELM PUMP • Built-in lock valve for positive rudder lock • Integral relief valve for over-pressure protection • 3⁄4 " tapered anodized aluminium shaft • Corrosion proof Model: composite housing Mounting: • Easy accessible lock valve and Displacement/ shaft seal for replacement Revolution: • For use with UC81-OBF No. of pistons: cylinder only Relief Valve Setting: • Intermediate dashboard Max Wheel Dia.: position mount Weight: UP18 Intermediate 18 cc – 1.1 cu.in. 5 55 Bar - 800 PSI 508mm (20'') 3.6kg (8lbs) Yamaha® Honda ® Suzuki® Tohatsu® Nissan® 3 UC81-OBF CYLINDER • Balanced: the number of turns lock-to-lock is equal port to starboard and vice-versa. • Depending on the applications on the outboard engine, the UC81-OBF can be installed port or starboard Model: Volume: Output force: Inside diameter: Stroke: Bleed fittings: 3 ⁄8 '' (9.5mm) Fittings: UC81-OBF 81 cc - 4.9 cu. in 222 kg - 489 lbs 27.4 mm - 1.08'' 186 mm - 7.3'' DN5 Quick connect For high pressure flex hose Selva® Johnson® Power 50 - 75 - 90 2 Stroke 115 EFI 2 Stroke 75 - 90 - 115 Optimax 2 Stroke 40 - 50 - 60 EFI 4 Stroke 75 - 80 - 90 EFI 4 Stroke 100 - 115 EFI 4 Stroke E40 - E50 - E55 - E60 2 Stroke E75 - E90 2 Stroke E115 2 Stroke V4 60 - 70 2 Stroke 75C - 90 2 Stroke 115C 2 Stroke F40G - F70 4 Stroke F30 - F40 - F60 - F75 - F80 EFI 4 Stroke F90 - F100 - F115 EFI 4 Stroke F80 - F100 4 Stroke F115 F40D - F50F - F60C EFI 4 Stroke BF40 - 50 - 60 - 75 - 90 4 Stroke BF115D BF115A BF90 V-TEC 4 Stroke DF40 - 50 - 60 - 70 - 80 - 90 4 Stroke DF100 - 115 4 Stroke* DF100 - 115 4 Stroke New Model 40 - 50 - 60 - 70 - 90 2 Stroke 75 - 115 2 Stroke 40 - 50TLDI 4 Stroke 70 - 90 - 115 TLDI 4 Stroke 40XS - 50 Madeira 2 Stroke 40XS - 50 Bull shark 2 Stroke 40XS - 60 Grey shark 2 Stroke 40XS - 70 Mako shark 2 Stroke 40XS - 60 St Tropez 2 Stroke 80 Portofino / Tigershark 2 Stroke 25 Kingfish 4 Stroke 40 Aruana 4 Stroke 40XS - 40XSR 50 - 60 Derado EFI 4 Stroke 40XSR EFI Murena 4 Stroke 80XS - 100 - 100XSR EFI Marlin 4 Stroke 115 - 115XSR EFI Tarpon 4 Stroke 115 - EFI Narwhal 4 Stroke BJ60 - 70 4 Stroke BJ90 - 115 4 Stroke J90 - 115 V4 2 Stroke Year 1990 - 2008 1990 - 2007 2004 to date 2004 to date 2000 to date 2007 to date 2004 to date 2004 to date 1995 to date 1984 - 2008 1998 - 2008 1990 - 2008 2010 to date 1999 - 2007 1999 - 2007 2000 to date 2004 to date 1995 to date 1998 - 2009 2009 to date 2008 to date 1998 to date 1998 - 2008 2008 to date 2004 to date 2004 to date 2004 to date 2004 to date 1995 to date 2000 to date 2001 -2007 2001 -2007 1995 -2007 *NOTE: Suzuki® engines built from 1998 to 2008 installing UC81-OBF cylinder require optional KIT SU Part No. 4-48130 42 CATALOGUE SUPPLEMENT - H Suitable for an outboard style engine up to 115hp and where the boat does not exceed 34.5mph (30 knots). NOT INTENDED FOR USE IN RACING APPLICATIONS Clean Tabs Water Care WATER FILTRATION NEW RANGE CLEAN TABS Use Puriclean to clean and disinfect the water tank and pipelines at least at the beginning and end of each season or use PuriSol instead if there are persistent bad odours. Use Aqua Clean Tabs to purify the water each time the tank is filled with water or use Aqua Sol instead if the water has bad tastes and odours. Use Waste-Guard for controlling odours emanating from the waste water tank. PURICLEAN (Cleans Tanks etc.) • Cleans the whole water system in boats, caravans, motor homes and coaches • Unique dual purpose formula which both cleans and sterilises in one easy action • Cleans the complete water system: tanks, pipes, pumps, hoses and taps • Eradicates bacteria, viruses, biofilm, algae and fungi • For maximum results, simply soak and flush • Proven in use world-wide for 3 decades Part No. 9-19800 100g x 12 tubs (each 100g tub cleans a tank up to 90 litres) Part No. 9-19801 400g x 6 tubs (each 400g tub cleans a tank up to 270 litres) AQUA SOL (Purifies) Aqua Sol is an advanced dual-purpose water purifying solution which kills all harmful organisms and eradicates foul tastes and odours, keeping stored water fresh and pure. Simply add AquaSol each time the tank or container is filled. Part No. 9-19806 300ml x 6 bottles (each bottle purifies 625 litres) WASTEGUARD Is a waste water deodoriser - odour control for grey waste water. • Destroys odours by oxidation - does not mask • Prevents contamination from bacteria • Keeps the sink drain fresh from odours • Eliminates fungal growth in the waste water tank Part No. 9-19808 300ml x 6 bottles AQUA CLEAN TABS (Purifies) • Rapid dissolving effervescent tablets for treating stored water • Aqua Clean Tabs kill bacteria, spores, cysts, algae, fungi, protozoa, viruses and causative water borne organisms • The water tank and system or container and filling hose should be periodically cleaned and purified with Puriclean Part No. 9-19804 Midi (x32) Tablets x 12 packs (1 tablet purifies 25 litres (5 gals) water) Part No. 9-19805 Mega (x18) Tablets x 6 packs (1 tablet purifies 225 litres (50 gals) water) PURI SOL (Cleans Tanks etc) Puri Sol is an advanced cleaner for water storage tanks formulated especially for periodic cleansing of water tanks and pipe work. Cleans, purifies and eliminates tastes and odours in water tanks and water systems. Triple Action: • Cleans water systems, tank, pipes, pump, taps • Destroys bacteria, viruses, spores, algae, fungi, cysts, and bacteria biofilm • Eliminates tastes and odours Formulation is a unique synergistic blend of chlorine dioxide and powerful cleaning components. When adding fresh water to the tank use only AquaSol to purify the water. Part No. 9-19807 300ml x 6 bottles (each bottle treats up to 250 litre tank) For Water Filtration Systems and Water Tanks See Section 9 of Our Catalogue CATALOGUE SUPPLEMENT - H 43 Mastervolt Electricals MASTERVOLT Available Summer 2014 MASS COMBI ULTRA 12V & 24V This compact inverter/charger combination with a smart transfer system, highly efficient MPPT solar charge regulator and separate second charger is all enclosed within a robust quality unit that is easy to install. Features include combining the latest V6 high frequency converter technology with ultra-fast and powerful DSP controls. This offers major user benefits such as a low ‘no load’ current, preventing your batteries from draining, and extreme peak power capability which allows high current loads such as air conditioning to start-up easily without power dips or light flickering. • Quiet operation The new Mass Combi Ultra fits perfectly into Mastervolt systems. All components are easily connected via MasterBus and installation can be controlled and monitored intuitively, even with just one MasterView Easy touchscreen. This will provide and manage all information about the Combi, the batteries and other sources such as the generator, grid or solar panels. The system is also suitable for Digital Switching, Mastervolt’s decentralised digital switching system. Part No. SINE WAVE INVERTER SPECIFICATIONS Model: Nom. DC voltage: Cont. power at 40 °C, cos phi 1: Surge capability: Parallel configuration: Output voltage (± 2%): Output waveform: 3-Phase configuration: Max. efficiency: Max. ripple on DC (battery): No-load power consumption (ON/inverter OFF/OFF): BATTERY CHARGER SPECIFICATIONS Nom. input voltage: Nom. battery voltage: Max. charge current at 40°C: Charge method secondary charger: Secondary charger output voltage: Secondary charger output current: Temperature sensor battery: GENERAL SPECIFICATIONS Display / Read-out: Dimensions (H x W x D): Weight: Approvals: TECHNICAL SPECIFICATIONS Charge characteristic: Ground relay: Temperature range (ambient temp.): Protection degree: Protections: MasterBus compatible: TRANSFER SYSTEM SPECIFICATIONS Generator input (switched): Mains input (switched): AC output 1: AC output 2 (switched): Transfer time: Transfer voltage range (adjustable): Transfer frequency range (adjustable): Power Sharing / Generator / Mains Support: SOLAR INPUT (DC) SPECIFICATIONS Input voltage range: Max. PV power: Max. input current: Max. charge current: MPP voltage range at nom. power: 44 NEW • Higher yield from solar power • Two AC inputs • Parallel and 3-phase operation • Unparalleled performance • Separate second charger • Optimal battery usage • Home comforts • Ease of installation M38013000 M38023500 12/3000-150 24/3500-100 12V (9.5 – 15.5V) 24V (19 – 32V) 3000 W 3500 W 6000 W – A 7000 W – A yes, up to 10 standard yes, up to 10 standard -------------------------------- 230 V - 50/60 Hz (± 0.005%) selectable ------------------------------------------------- true sine wave, Thd < 1% under standard conditions -----------------yes yes 90% 91% < 10% < 10% 16W / 2W / 0W 16W / 2W / 0W 180 – 275V 180 – 275V 12V 24V 150A at 14.25V 100A at 28.5V ----------------------------- IUoU, automatic 3-step+ or constant voltage -----------------------12V 12-24V adjustable 10A 10A yes, included yes, included LED display LED display --------------------------- 472 x 318 x 175mm (18.6 x 12.5 x 6.9 inches) ---------------------15kg (33.1 pounds) 15.3kg (33.7 pounds) CE, E-mark, ABYC CE, E-mark, ABYC IUoU, automatic 3-step+ for AGM/gel/Lithium Ion/flooded/flooded traction/spiral/NiCad adjustable adjustable ----------------------- -25°C to 80°C, derating > 40 °C (-13 to 176 °F) ----------------------IP23 (vertical mounting) IP23 (vertical mounting) over temperature, AC over load, AC short circuit, DC short circuit, high battery, low battery yes yes 50A 30A 67A 50A seamless (UPS, < 1 ms) 180 – 275V 35 – 65Hz yes 50A 30A 67A 50A seamless (UPS, < 1 ms) 180 – 275V 35 – 65Hz yes 15-100V 500 Wp 18A 30A at 14.25V 35-80V 15-100V 500 Wp 18A 15A at 28.5V 35-80V CATALOGUE SUPPLEMENT - H Mastervolt Electricals MASTERVOLT ALPHA ALTERNATOR KITS The main engine alternator is designed to charge the starter battery. As a result the combination is not ideal for fast & full charging of other batteries such as the service or bowthruster battery. Especially for chargeing batteries over a short time or when a little more power is required. M48512090 There are two options to solve this issue: Equip the standard alternator with an Alpha Pro II MB charge regulator, ensuring that the existing alternator works in accordance with the 3-step charge technology instead of it’s standard 1-step method, and that the batteries are charged faster within a shorter period. Or use a powerful second Alpha alternator with Alpha Pro II MB charge regulator. This is specifically designed for charging service batteries, and allows you to charge quickly and turn off your engine when you moor. M48512130 M48524075 M48524110 • Fast & complete charging of starter/service/bowthruster batteries. • Power supply for all consumers. • 12V and 24V versions. • 75 A to 150 A charge current. • Supplied with Alpha Pro II MB charge regulator for optimal performance & longer-lasting batteries. M48524150 Part No.s in Red = To Order Only Part No. Model: Type Cabinet: Charge Current: Alpha Pro Charge Regulator: Charge Voltage Absorption: Charge Voltage Float: Cable Length Regulator/Alternator: Pulley (double) diameter: Belt section: Isolated from Mass: Direction of Revolutions: Weight: Dimensions: Mounting: M48512090 M48512130 M48524075 M48524110 M48524150 12/90 12/130* 24/75* 24/110 24/150 A B B B C 90A 130A 75A 110A 150A Standard Standard Standard Standard Standard 14.25V 14.25V 28.5V 28.5V 28.5V 13.25V 13.25V 26.5V 26.5V 26.5V ------------------------- 1.5m (5ft) oil resistant marine connection cable - delivered as standard ------------------------------73mm (2.9") 88mm (3.5") 88mm (3.5") 88mm (3.5") 92mm (3.6") 2xA 2xA 2xA 2xA 2xA Yes Yes Yes Yes Yes 2 2 2 2 2 5.5kg (12.1lbs) 10.1kg (22.2lbs) 10.1kg (22.2lbs) 10.1kg (22.2lbs) 13.1kg (28.9lbs) ------------------------------------------- see www.mastervolt.com/alternators for the drawings ---------------------------------------five to six, six o’clock six o’clock six o’clock five to six, six o’clock and six o’clock and five past six five past six Charge Regulation: -------------- The Alpha Pro II Charge Regulator is supplied as standard with all models, see below ------------* Available with multi-groove pulley (12/130 model = Part no. M48512131 24/75 model = Part no. M48524076) ALPHA PRO II MB CHARGE REGULATOR The Alpha Pro II MB charge regulator is designed as a ‘fit all’ solution, just one unit is needed for both 12 and 24V applications with a simple selector switch to set the regulator to the right voltage. The unit can also be used on any other brand of alternator that has a standard Bosch connector, with a cable supplied as standard in the box. Easy operation LEDs on the body of the regulator indicate the charge phase. NEW Connection cable delivered as standard. Part No.: Link to MasterShunt: Connection to Mastervolt alternator: Connection to Bosch alternator: Cooling: Nom. output voltage: Cable length regulator/alternator: Cable length temperature sensor: Connection plug regulator/alternator: Display/read-out: Dimensions, hxwxd: Weight: Approvals: Charge characteristic: Charge voltage Bulk: Charge voltage Absorption: Absorption time: Charge voltage Float: Temperature compensation: Voltage compensation: Alternator type: Protection degree: MasterBus compatible: M45512000 yes yes yes fanless 12 V / 24 V 1.5 mtr oil resistant connection cable 6 mtr Alpha/Mastervolt LED display 90x109x30 mm 3.5 x 4.3 x 1.2 inches 0.4 kg 0.9 pounds CE IUoUo, automatic / 3-step+ for gel/AGM/wet/Lithium Ion 14.25 V / 28.5 V 14.25 V / 28.5 V 4 hours, adjustable from 2 minutes to 12 hours 13.25 V / 26.5 V -30 mV / °C -17 mV/ °F voltage drop compensation in DC cables up to 3V various IP65 yes Plus connection cable for Bosch alternator. CATALOGUE SUPPLEMENT - H 45 Mastervolt Electricals MASTERVOLT MASTERVOLT COMFORT SYSTEM Knowing that trawling through catalogues collecting part numbers for various components and designing a system can be time consuming, Mastervolt has created the ultimate kit. Normally, the 7 components needed would all require their own part number, however, now just one part number – and one box – covers them all. Part No. M77712505. The Comfort System consists of a charger/inverter combination, shore connection, battery monitoring, monitored main fuses and one touch screen panel. Complete overview of the Comfort System: M36012505 M77020100 M77020200 M77049250 M77010305 M121160250 M121160000 Mass Combi 12/2500 MasterShunt 500 DC Distribution 500 ANL fuse 250 A; Combi fuse that can be mounted in DC Distribution MasterView Easy Shore power cable 16 A/ 25 mtr / 3x 2.5 mm² Shore power inlet (European layout/pin & sleeve) The system approach of the Comfort System also means that customers can upgrade and expand this straightforward installation with further plug & play Mastervolt components in the future. The Comfort System is particularly suitable for 30-50 ft yachts and luxury mobile homes, with sufficient power for onboard electric consumers like a coffee maker and microwave. Mastervolt Comfort System Installation Overview 3x 2.5mm2 RCD* RCD* Power Output Grid/Shore Power Short Break Output Kettle TV Hairdryer Microwave Computer 95mm2 + – 12V Battery bank* >200Ah <500Ah Battery switch* for winter storage or maintenance only 70mm2 for lengths <3m Before first use, the MasterShunt has to be set up. Refer to the Direct loads/power input user’s manual. * Not included Battery Switch* to disconnect consumers A MasterView System configuration .mvc file is available at mastervolt.com/marine/systems For more Mastervolt products see our printed catalogue or visit our website: www.aquafax.co.uk 46 CATALOGUE SUPPLEMENT - H Marinco BEP Pro Installer Series ELECTRICS NEW RANGE MARINCO BEP PRO INSTALLER SERIES Onboard power demands continue to increase as boaters request the comforts of home on their boats. Marinco and BEP looked at the common products used by electrical installers every day and made significant improvements to their design and construction. The result is a robust product line with greater capacity and extended product life. The valuable space saved onboard gives builders or installers greater flexibility when designing power systems. Since Pro Installer modular assemblies are designed for fast, flexible installation in tight spaces, it's easy to “cluster” products and reduce their mounting footprint. The common interconnection height enables solid link bars to connect multiple Pro Installer products – a smart design feature for watercraft. Like all Marinco products by BEP, you can be assured of durable construction engineered specifically to handle the challenging marine environment. High-temperature, fiber-reinforced base material provides strength and chemical resistance. All Pro Installer products include a common interconnection height, label recess on the cover, ability to “cluster” and a compact footprint. All studs, washers and nuts are made of stainless steel. Features and Benefits: • Common interconnection height makes it easy to ‘cluster’ products • Modular assemblies offer unrivalled flexibility in design/layout • Reduced individual footprints save additional space for the most compact installations • Robust construction for the harshest of marine environments Innovative clear covers insulate/protect on three sides, and include recesses for convenient labelling Covers feature snap-out side skirts for additional cable entry as required Stainless steel studs, washers and nuts Tin plated copper conductors Radiused bar ends and generous stud lengths improve cable routing options for large cables High-temperature, fibre reinforced base materials for strength and chemical resistance Product Footprints See individual products for footprint size. PRO INSTALLER HEAVY-DUTY BUSBARS Pro Installer Heavy Duty Busbars provide a robust means to connect (bus) together the multitude large cables found in modern electrical installations. These offer unrivalled flexibility to meet the requirements of any installation, saving significant cost and space. Specifications: • 4 Stud-500A busbar: 8mm (5/16") stainless steel studs • 3, 5, and 8 stud-650A busbars: 10mm (3/8") stainless steel studs • Studs treated with anti-seize lubricant • 50 VDC • Tinned CDA102 Copper conductors • Stainless steel studs, washers, nuts for longevity in the marine environment • Generous stud lengths, metric threads Part No.: Description:: Stud Detail: Amps: Dimensions (mm): Dimensions (Inches): Weight: Footprint: 8-93501 3 Stud Busbar 3x 10mm (3/8") 650A 98 x 49 x 61 3.9" x 1.9" x 2.4" 294g (10.4 oz) 1x 8-93502 4 Stud Busbar 4x 8mm (5/16") 500A 98 x 49 x 61 3.9" x 1.9" x 2.4" 272g (9.6 oz) 1x 8-93501 8-93504 8-93502 8-93503 5 Stud Busbar 5x 10mm (3/8") 650A 147 x 49 x 64 5.8" x 1.9" x 2.5" 506g (17.9 oz) 1.5x 8-93504 8 Stud Busbar 8x 10mm (3/8") 650A 249 x 49 x 64 9.8" x 1.9" x 2.5" 841g (29.7 oz) 2.5x 8-93503 CATALOGUE SUPPLEMENT - H 47 Marinco BEP Pro Installer Series ELECTRICS NEW RANGE PRO INSTALLER Z BUSBARS Marinco BEP Products have created a completely new concept for small cable termination with the Z-Bar range. These busbars maximize power density by utilizing high and low level bars to optimize cable runs, saving even more installation space. Specifications: • 10 Way and 18 Way versions • 4x 6mm (1/4") studs with anti-seize lubricant • 4mm (5/32") terminals with captive lock washers • 200A maximum per bar (2x 200A) • 50 VDC • Tinned CDA102 Copper conductors • Stainless steel studs, washers, nuts for longevity in the marine environment • Metric threads Part No.: Description: Stud Detail: 8-93510 10 Way Z Busbar 4x 6mm (1/4") 18 x 4mm (5/32") 2 x 200A 98 x 49 x 51 3.9" x 1.9" x 2.0" 203g (7.2 oz) 1x Amps: Dimensions (mm): Dimensions (Inches): Weight: Footprint*: 8-93511 8-93511 18 Way, Z Busbar 4x 6 (1/4") 18 x 4mm (5/32") 2 x 200A 147 x 49 x 51 5.8" x 1.9" x 2.0" 280g (9.9 oz) 1.5x 8-93510 *See page 47 for footprint info. PRO INSTALLER ANL FUSE HOLDERS These ANL fuseholders offer unparalleled circuit protection choice for both the installer and end-user. The innovative Through-Panel fuseholder (8-93522) provides superior access for fuse inspection and replacement. Small electrical loads are catered to with the compact 8-93520 unit while additional cable security and highest capacity is provided by the 8-93521, featuring additional studs for separate clamping of cables. Specifications: • Cable connection studs: Shared 8mm (5/16") on 8-93520 • 10mm (3/8") studs on 8-93522 and 8-93521 • Fuse mounting studs: 8mm (5/16") • Double washers allow any ANL fuse brand to be fitted • Fuse type: ANL or ANN (fast blow) • Swinging fuse style allows changing fuse without removal of fastening nuts • Amperage: determined by fuse sizing, 8-93520 (35-300A), 8-93521 (35-750A), 8-93522 (35-500A) • 50 VDC (or determined by fuse fitted) • Tinned CDA102 copper conductors 8-93521 • Tinned CDA260 high conductivity brass conductors 8-93522 Part No.: Description: 8-93520 Fuseholder, ANL Stud Detail: 2x 8mm (5/16") Amps: Dimensions (mm): Dimensions (Inches): Weight: Footprint*: 35 - 300A ANL 98 x 49 x 54 3.9" x 1.9" x 2.1" 143g (5.0 oz) 1x 8-93521 Fuseholder, ANL with additional cable clamping studs Fuse: 2x 8mm (5/16") 2x 10mm (3/8") 35 - 750A ANL 147 x 49 x 61 5.8" x 1.9" x 2.4" 330g (11.6 oz) 1.5x *See page 47 for footprint info. 48 CATALOGUE SUPPLEMENT - H 8-93521 8-93520 8-93522 Fuseholder, ANL through panel Fuse: 2x 8mm (5/16") 2x 10mm (3/8") 35 - 500A ANL 98 x 49 x 36* 3.9" x 1.9" x 1.4"* 298g (10.5 oz) 1x 8-93522 Marinco BEP Pro Installer Series ELECTRICS NEW RANGE PRO INSTALLER CLASS-T FUSE HOLDERS Class-T fusing provides the ultimate protection for high power circuits, and where extremely fast fuse blow characteristics are required. Modern battery technologies such as Mastervolt Lithium Ion or AGM are capable of very high short circuit currents which may be beyond the interrupt rating of standard circuit breakers and other types of fuse. Two sizes of Pro Installer Class-T Fuseholder are available which accommodate fuses from 225-400 Amps, and 450-600 Amps respectively. Specifications: • Cable connection studs: 10mm (3/8") studs • Fuse mounting studs: 10mm (3/8") 225-400A holder, 12mm (1/2") 450-600A holder • Fuse type: Class-T (JLLN / TJN / A3T) • Maximum amperage: Determined by fuse sizing, either 400A or 600A • 50 VDC • High temperature, fibre reinforced plastic base provides strength and chemical resistance • Clear polycarbonate cover • Tinned CDA102 Copper conductors • Stainless steel studs, washers and nuts for longevity in the marine environment • Metric threads PRO INSTALLER INSULATED STUDS Pro Installer Insulated studs are available in single and twin stud versions, featuring 8mm (5/16") and 10mm (3/8") variants. A double stud version with 10mm and 8mm studs is also included for extending outboard motor cables. The Power Tapping Plate single stud models provide convenient termination points for additional small cables. Pro Installer family features are replicated with these insulated studs, generous stud length, modular footprint, insulating covers with label recess, common interconnection height. Part No.: Description: 8-93531 Single 8mm Insulated Stud with 4mm power tapping plate Stud Detail: 1x 8mm (5/16") 1x 8mm (5/16") Insulated Stud 4x 4 (5/32") Amps: – Power Plate 4 x 50A Dimensions (mm): 49 x 49 x 62 49 x 49 x 62 Dimensions (Inches): 1.9" x 1.9" x 2.4" 1.9" x 1.9" x 2.4" Weight: 74g (2.6 oz) 106g (3.7 oz) Footprint: 0.5x 0.5x Part No.: Description: 8-93530 Single 8mm Insulated Stud 8-93540 Single 10mm Insulated Stud 8-93541 Single 10mm Insulated Stud with 4mm power tapping plate Stud Detail: 1x 10mm (3/8") 1x 10mm (3/8") Insulated Stud 4x 4 (5/32") Amps: – Power Plate 4 x 50A Dimensions (mm): 49 x 49 x 62 49 x 49 x 62 Dimensions (Inches): 1.9" x 1.9" x 2.4" 1.9" x 1.9" x 2.4" Weight: 85g (3.0 oz) 117g (4.1 oz) Footprint: 0.5x 0.5x *See page 47 for footprint info. 8-93525 8-93524 Part No.: Description: Stud Detail: 8-93524 ClassT Holder 4x 10mm Amps: Dimensions (mm): Dimensions (Inches): Weight: Footprint*: 225-400A Class-T 147 x 49 x 61 5.8" x 1.9" x 2.4" 351g (12.4 oz) 1.5x 8-93525 ClassT Holder Fuse: 2x 12mm (0.47") 2x 10mm (3/8") 450-600A Class-T 147 x 49 x 61 5.8" x 1.9" x 2.4" 382g (13.5 oz) 1.5x *See page 47 for footprint info. Specifications: • Power tapping plate: 4x 4mm (5/16") terminals • Maximum current through power tapping plate: 50A per terminal (4x 50A maximum) • Note: no power passes through the stud so no amp rating is given • 50 VDC • High temperature, fibre reinforced plastic base provides strength & chemical resistance • Clear polycarbonate cover with snap-out extra cable access • Stainless steel studs, screws and nuts for longevity in the marine environment • Insert moulded studs with metric threads • Double studs feature ‘snap out’ insulating partition, to allow linking of studs 8-93532 Double 8mm Insulated Stud 2x 8mm (5/16") Insulated Stud – 49 x 49 x 62 1.9" x 1.9" x 2.4" 98g (3.5 oz) 0.5x 8-93530 8-93532 8-93531 8-93542 Double 10mm Insulated Stud 8-93544 Double 10mm/8mm Insulated Stud 2x 10mm (3/8") Insulated Stud – 49 x 49 x 62 1.9" x 1.9" x 2.4" 122g (4.3 oz) 0.5x 1x 8mm (5/16"), & 1x 10mm (3/8") – 49 x 49 x 62 1.9" x 1.9" x 2.4" 110g (3.9 oz) 0.5x 8-93540 8-93542 8-93541 8-93544 CATALOGUE SUPPLEMENT - H 49 Thetford Portable & Cassette Toilets N-28639 Part No. N-28640 Model HxWxD Colour Waste Tank Flush Total (mm) Capacity Water Tank Weight N-28639 PP Qube 335 315 x 342 x 382 White 10 Litres 10 Litres 3.3Kg N-28640 PP Qube 365 414 x 383 x 427 White 21 Litres 15 Litres 4.0Kg THETFORD PORTA POTTI EXCELLENCE Thetford have introduced the Porta Potti Excellence to their portable toilet range combining a sleek and sophisticated design, with comfort and quality. • Manual piston pump or electric flush operation • Push button vent on waste tank reducing splashing when emptying • Integrated rotating empty spout fitted to waste tank • Waste tank level indicator included • Includes waste tank and flush fluid samples • Integrated folding toilet roll holder Description Lipseal Vent Seal Vent Button Water Cap Holding Tank White Holding Tank Grey Dump Cap Piston Pump Grey Piston Pump White Water Tank White Water Tank Granite Holding Tank White Holding Tank Granite Dump Cap White Water Cap White Vent Button White Piston Pump White Piston Pump White Water Cap White Water Cap Granite Piston Pump White Dump Cap White Electric Pump White ✔ ✔ ✔ ✔ ✖ ✖ ✔ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✔ ✔ ✔ ✔ ✖ ✖ ✔ ✔ ✔ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✔ ✔ ✔ ✔ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ Qube Part No. N-28600 N-28601 N-28602 N-28603 N-28604 N-28605 N-28606 N-28607 N-28608 N-28612 N-28613 N-28614 N-28615 N-28660 N-28661 N-28662 N-28663 N-28664 N-28670 N-28671 N-28672 N-28674 N-28675 465 • Manual piston pump flush operation • Push button vent on waste tank reducing splashing when emptying • Integrated rotating empty spout fitted to waste tank • Waste tank level indicator included • Includes waste tank and flush fluid samples • Hold down kit included with Qube 335 portable toilet 365 PORTAPOTTI PARTS 345 The Porta Potti Qube forms the basis of a new generation of durable portable toilets from Thetford offering better appearance, functionality and comfort. 335 THETFORD PORTA POTTI QUBE ✔ ✔ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✔ ✔ ✔ ✔ * ✔† ✖ ✖ ✖ ✖ ✖ Excellence PLUMBING - TOILETS ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✖ ✔ ✖ ✖ ✔ ✔ ✔ ✔ ✔ * Fits 335 Qube only. † Fits 365 Qube only. * Electric uses 6 x 1.5V AA Batteries Part No. Model HxWxD (mm) Colour Waste Tank Flush Capacity Water Tank N-28643 PP Excellence 448 x 388 x 450 White N-28644 PP Excellence 448 x 388 x 450 White 21 Litres 21 Litres 15 Litres 15 Litres Flush Total Operation Weight Piston Pump 5.3kg Electric* 5.5kg THETFORD C402C & C403L CASSETTE® TOILET These models have a fixed toilet bowl and can be installed using either left or right models. The waste holding tank has wheels and a retractable handle to allow ease of handling. In addition, the working mechanism in the waste holding tank is removable, making the inside of the tank easy to clean and maintain, while an advanced level indicator display shows the levels in the waste holding tank and/or flush-water tank. C-402C models that have their own flush-water tank. C-403L models that are connected to the boat's water tank. • Optimal use of space & lightweight C402/403 PARTS • Level indicator: time to empty the waste holding tank Part No. Description • Waste tank with wheels N-28631 C402 Pump • Removable mechanism N-28632 C402/403 Holding Tank L/H Grey • Vent plunger for emptying without splashing N-28633 C402/403 Holding Tank R/H Grey • High-quality plastic for a durable, user-friendly and N-28635 C400 Fresh Up Kit maintenance-friendly toilet • Automatic pressure release vent prevents build-up of gases in the waste holding tank • In-built emptying spout: no fiddling about with loose parts • Powerful flushing system Set combines • 12 Volt DC operation a waste-holding tank with a Part No. N-28506 N-28507 N-28508 N-28509 50 Model C402C C402C C403L C403L Flush Electric Electric Electric Electric Installation Right Hand Left Hand Right Hand Left Hand Net Weight 8.1kg 8.1kg 9.1kg 9.1kg seat & cover and free toilet fluids. CATALOGUE SUPPLEMENT - H Model C402C C403L Dimensions (mm): A B C D 400 258 670 458 400 258 670 458 E 358 358 Capacities Fresh Water Waste Tank 15 19.3L – 19.3L Thetford Cassette Toilets & Accessories PLUMBING - TOILETS *N-28505 excludes water fill door (N-28625) which can be ordered separately if required. THETFORD C200CS & C200CW CASSETTE® TOILETS (excluding door*) These models are equipped with a toilet bowl that can revolve 180º on the toilet base. Downward pressure on the seat locks the toilet bowl into the desired position. They can be installed as freestanding units against any outer wall of the boat. Because you can revolve the toilet bowl before use, you experience optimal comfort without losing any space. C-200CS: models that are connected to the boat's water tank. C-200CW: models that have their own flush-water tank. • Optimal use of space & lightweight • Level indicator: time to empty the waste holding tank • Removable mechanism • Vent plunger for emptying without splashing • High-quality plastic for a durable, userfriendly and maintenance-friendly toilet • Automatic pressure release vent prevents build-up of gases in the waste holding tank • In-built emptying spout: no fiddling about with loose parts • Powerful flushing system • 12 Volt DC (Electric Flush) Part No. Model Flush Net Weight N-28504 C200CS Electric 7.2kg N-28505* C200CW Manual 7.6kg Model C200CS C200CW A 538 728 N-28634 C200 PARTS Part No. N-28619 N-28620 N-28621 N-28622 N-28623 N-28624 N-28625 N-28626 N-28627 N-28628 N-28634 Dimensions (mm): B C D E 500 353 822 495 500 353 822* 495 F 430 430 Description C200CS/CW Seat & Cover White C200CS Flush Switch C200CS/CW Holding Tank Grey C200CS/CW C400 Lipseal C200CS/CW Automatic Vent C200CS/CW Blade Opener C200CW Water Fill Door White C200CS/CW Measuring Cup C200CS/CW Tank Slide C200/250/260/400 electric valve C200 Fresh-up Kit Capacities Fresh Water Waste Tank – 17L 7 17L *Height of toilet seat open 327mm N-28504 N-28505* TOILET SERVICE DOOR 3 • Modern, streamlined appearance • Watertight and UV resistant • Double seal ensures optimum insulation • Special secure push-button locks - they can’t spring open unexpectedly or be forced open • Easy self-installation, horizontally or vertically • Easy step-by-step guide supplied Dimensions (h x w): with a template for creating the Overall: 385 x 335mm opening in the boat wall Door Open: 330 x 280mm • Suitable for walls between 23 & Part No. N-28511 39mm thick THETFORD C263-CS BUILD IN CASSETTE TOILET This contemporary homelike design provides simple operation and features a 180º rotating bowl allowing perfect position to suit the bathroom compartment. The C263-CS connects to the boat water system for flushing and is also available with a ceramic easy clean bowl liner. • Use friendly control panel with push button flush • Connects to boat water system for powerful flush operation • Large 17.5L volume holding tank with integrated wheels and pull out handle • Fitted with waste holding tank level indicator • Available with ceramic easy clean bowl liner • 12 Volt DC operation Waste holding tank C263 PARTS Part No. N-28514 N-28622 N-28628 N-28636 Part No. N-28646 N-28647 Description C250/260 cassette holding tank C200CS/CW C400 lipseal C200/250/260/400 electric valve C250/260 Fresh-up Kit Model C263-CS C263-CS H x W x D (mm) 750 x 417 x 603mm 750 x 417 x 603mm N-28636 Colour White White FOR SPARES NOT LISTED PLEASE CONTACT YOUR LOCAL AQUAFAX SALES DEPOT Waste Tank Capacity 17.5 Litres 17.5 Litres Bowl Liner Standard Ceramic Flush Water Outlet 10mm ID hose 10mm ID hose Total Weight 8.0Kg 17.5Kg CATALOGUE SUPPLEMENT - H 51 Speedfit Pushfit Plumbing Fittings PLUMBING - FITTINGS SPEEDFIT PLUMBING FITTINGS - New push-fit plumbing fittings available from Aquafax DZR Brass Female Coupler • Manufactured in DZR Brass • No scale build up and corrosion free • BSI and WRAS approved 15mm x 1⁄2 " BSP 22mm x 3 ⁄4 " BSP P/No. 9-84014 P/No. 9-84015 Plastic Ball Valve Barrier Pipe • Suitable for central heating systems • Pex material • Manufactured and kitemarked to British Standard BS7291: Part 3: Class S • Lightweight and flexible • Lead free and non toxic Not suitable for central heating systems • Both red and blue indices supplied • Lead free and non toxic • BSI and WRAS approved 15mm x 15mm 22mm x 22mm P/No. 9-84072 P/No. 9-84073 For more Speedfit Barrier Pipe see Section 9, page 13. 15mm x 6m 15mm x 6m 15mm x 6m 22mm x 6m 22mm x 6m Red Blue White Red Blue P/No. 9-84412 P/No. 9-84413 P/No. 9-84414 P/No. 9-84419 P/No. 9-84420 The items below are now available carded - see Section 9 pages 11 -13 for full ranges. Female Coupler Tap Connector End Stop Hose Connector Requires hand tightening only 15mm x 3 ⁄8 " BSP P/No. 9-84000P 15mm x 1⁄2 " BSP P/No. 9-84001P 15mm P/No. 9-84061P Chromed Brass Service Valve DZR Brass Male Coupler P/No. 9-84101P NOT suitable for central heating systems. Hot and cold water only 65ºC Maximum 15mm x 1⁄2 " BSP P/No. 9-84165P DZR Brass Male Stem Adaptor Stem Reducer 15mm 15mm x 1⁄2 " BSP P/No. 9-84011P 15mm x 1⁄2 "ID Bent Tap Connector P/No. 9-84066P Plastic Service Valve 22mm x 15mm P/No. 9-84121P Inline Hot & Cold Tap Equal Tee 15mm x 1 ⁄2 " BSP P/No. 9-84171P 22mm x 3 ⁄4 " BSP P/No. 9-84172P DZR Brass Female Stem Adaptor 15mm x 15mm P/No. 9-84071P 15mm 22mm P/No. 9-84021P P/No. 9-84022P NOT suitable for central heating systems. Hot and cold water only 65ºC Maximum 15mm P/No. 9-84130P DZR Brass Drain Cock NOT suitable for central heating systems. Hot and cold water only 65ºC Maximum 15mm P/No. 9-84031P P/No. 9-84032P Equal Straight Connector Straight Coupling Reducer Stem Elbow Equal Elbow 15mm 22mm 15mm x 1 ⁄2 " BSP P/No. 9-84176P P/No. 9-84075P Suitable for central heating systems. Cannot be used where collett covers are fitted. Can be used with a standard fitting fitted with a collet clip White Collet Clip (Pack Qty) 15 x 12mm P/No. 9-84191P 22 x 15mm P/No. 9-84192P 15 x 15mm P/No. 9-84151P Straight Tap Connector Reducing Tee 2 1 3 15mm 22mm 52 P/No. 9-84041P P/No. 9-84042P 15mm 22mm P/No. 9-84093P (10) P/No. 9-84094P (10) CATALOGUE SUPPLEMENT - H 15mm x 1⁄2 " BSP P/No. 9-84161P 15 x 15 x 22mm P/No. 9-84385P 22 x 15 x 15mm P/No. 9-84387P Hep2O Plumbing Fittings PLUMBING - FITTINGS HEP2O PLUMBING FITTINGS The new, technologically advanced next generation Hep2O range is here. Packed with revolutionary unique new features, In4Sure™ joint recognition that actually tells you when inserted and the HepKey™ demounting system provides super-secure but fully demountable joints. Hep2O is quicker, more reliable and easier to use than ever before. And while the fittings are all totally new, it’s still the same easy to work with pipe as before, the colour has just changed to white. 50 Year Guarantee against defects in materials or manufacturing of all Hep2O pipe & fittings. Hep2O is manufactured and kitemarked to Class S of BS 7291 In4Sure™- How it Works The profiled end of the re-designed SmartSleeve™ pipe insert (P-51360) works with the internal castellations of the new Hep2O fitting. Just insert, push, twist and feel for the rumble to know the pipe is fully inserted, making a 100% secure connection. Internal castellations Hep2O fitting Super-tough new white fitting. HepKey™- How it Works The innovative pipe release key that only demounts when you want it to. Colour-coded to the pipe size, the HepKey™ triggers the grab-ring within the fitting to release the pipe. As the fitting is tamper-proof, the pipe will only release when you want it to. So it’s fast, simple and eliminates the risk of accidental and potentially expensive demounting. *Pocket-sized HepKey™ coming soon. Grab-ring Strong, high quality 316 stainless steel re-engineered grab-ring. Able to grip plastic and copper pipe, the carefully angled teeth have been aligned for easy fitting and maximum grip. Polybutylene Pipe Cuts, bends and comes off the coil straight, in exactly the same way it always has. O-ring Offers a reliable seal in both hot and cold water systems. SmartSleeve™Pipe Insert The profiled end allows joint recognition, reduces the force required to make a secure connection, and stays in the pipe when demounted. HepKey Plus™ Available in each of the four fitting sizes, HepKey Plus™ simply clips onto the fitting, depresses the inner collar which releases the integral grab-ring and allows the pipe to be removed. Hep2O fitting Super-tough new white fitting. HepKey™ The smaller pocket-sized* HepKey™ clips around the pipe and needs to be pushed against the fitting to release the pipe. Quick and easy to use and it achieves demounting with the minimum of effort. Hep2O® POLYBUTYLENE PIPE Same Great Pipe – Now in White. Not everything has changed. Hep2O pipe remains the same, all except for the colour. It’s still exceptionally flexible and still comes off the coil in straight useable lengths that can easily be cabled into position. The only thing that’s changed is the colour. Now in white to match the new fittings, exposed areas of pipe work now look clean and more attractive. Size 10mm 15mm 15mm 15mm 15mm 15mm 22mm 22mm 22mm 22mm Length 50m Coil 25m Coil 3m Straight 6m Straight 50m Coil 100m Coil 3m Straight 6m Straight 25m Coil 50m Coil Model HXX50/10 HXP25/15 HXP03/15 HXX06/15 HXP50/15 HXP100/15 HXP03/22 HXX06/22 HXP25/22 HXP50/22 All BiTite™ Hep2O fittings are fully compatible with Hep2O pipe & copper pipe. SEE SECTION 1 FOR COPPER PIPE. Type Barrier Standard Standard Barrier Standard Standard Standard Barrier Standard Standard Grab-ring Located behind the release sleeve, it is captive within the fitting so can’t fall out and get lost. Manufactured from high quality 316 stainless steel that can be used repeatedly without any loss of strength so the fitting can be used and re-used. For Calorifiers, Sinks & Taps See Section 9 Part No. P-51001 P-51002 P-51003 P-51004 P-51005 P-51006 P-51007 P-51008 P-51010 P-51009 CATALOGUE SUPPLEMENT - H 53 Hep2O Plumbing Fittings PLUMBING - FITTINGS The Professional Flexible Plumbing System for Hot & Cold Water & Central Heating AUXILIARY BiTite™ FITTINGS FEMALE ADAPTOR WALL PLATE ELBOW DZR Brass / new white plastic. Size Model 1 ⁄2 " BSPF x15mm HX6/15 DZR Brass / new white plastic socket. Size Model Part No. 1 ⁄2 " BSP x 15mm HX28/15 P-51228 3 ⁄4 " BSP x 15mm HX24/15 P-51228A 3 ⁄4 " BSP x 22mm HX28/22 P-51328 1'' BSP X 28mm HX28/28 P-51428 Part No. P-51206 MALE ADAPTOR BALL VALVES DZR Brass / new white plastic socket. Size Model Part No. 1 ⁄2 " BSP x 15mm HX29/15 P-51229 3 ⁄4 " BSP x 22mm HX29/22 P-51329 1'' BSP X 28mm HX29/28 P-51429 Chrome Nickel finish Brass ball valve, new white plastic. Size Model Part No. 15mm (85x50x120mm) HX22 P-51233 22mm (96x60x142mm) HX22 P-51333 FEMALE ADAPTOR DZR Brass / Hep2O spigot Size Model 1 ⁄2 " BSP x 15mm HX30/15 3 ⁄4 " BSP x 22mm HX30/22 CYLINDER CONNECTOR DZR Brass (cone ended socket adapter with nut) Size Model Part No. 1" BSP x 22mm HX34/22 P-51334 MALE ADAPTOR DOUBLE CHECK VALVE New white plastic. Size 15 x 15mm Model HX72/15 DZR Brass / Hep2O spigot Size Model 1 ⁄2 " BSP x 15mm HX31/15 3 ⁄4 " BSP x 22mm HX31/22 1" BSP x 28mm HX31/28 Part No. P-51272 GATE VALVE (HOT/COLD) Size Model 1 ⁄2 " Hose x 15mm Spigot HX32/15 Part No. P-51235 P-51335 All new white plastic with reversible top for either hot or cold. Size Model 15 x 15mm HX37/15 Part No. P-51236 P-51336 Model HX39/15 Part No. P-51237 APPLIANCE VALVE (HOT/COLD) ADAPTOR Brass reducing socket. Size 1 ⁄2 " BSPM x 3⁄8 " BSPF Part No. P-51232 SHUT OFF VALVE (HOT/COLD) STOP COCK (COLD WATER) Model HX36/15 HX36/22 Part No. P-51231 P-51331 P-51431 BRASS DRAIN COCK Brass / new white plastic. Size Model 15 x 15mm HX35/15 22 x 22mm HX35/22 New white plastic. Size 15 x 15mm 22 x 22mm Part No. P-51230 P-51330 All new white plastic with reversible top for either hot or cold. Size Model 3 ⁄4 " BSP x 15mm HX38/15 Part No. P-51239 Part No. P-51238 REPLACEMENT FITTINGS & ACCESSORIES FOR BiTite™ Hep2O™ FITTINGS 54 HEPKEY DEMOUNTING TOOL BLANKING PEG (Pack of 10) ‘O’ RING (Pack of 20) GRAB WEDGES (Pack of 20) (Pack of 10) Size Model Part No. 15mm HX79/15 P-51251 22mm HX79/22 P-51351 Size 15mm 22mm Size 15mm Size 15mm Model Part No. HX44/15 P-51252 HX44/22 P-51352 CATALOGUE SUPPLEMENT - H Model Part No. HX51/15 P-51257 Model Part No. HX46/15 P-51258 Hep2O Plumbing Fittings PLUMBING - FITTINGS The Professional Flexible Plumbing System for Hot & Cold Water & Central Heating PIPE FITTINGS AND ACCESSORIES COLD FORMING BEND Metal fixture with passivate finish Size Model Part No. 15mm HX75/15 P-51275 22mm HX75/22 P-51375 PIPE CLIP White plastic - Screw fixing (Bag of 50) Size Model Part No. 15mm HX85/15 P-51285 22mm HX85/22 P-51385 28mm HX85/28 P-51485 SMARTSLEEVE PIPE SUPPORT S/S Sleeve. Always fit a support sleeve Size 15mm 22mm 28mm Model HX60/15 HX60/22 HX60/28 Part No. Pack Qty P-51260 50 P-51360 50 P-51460 20 PIPE CLIP Plastic - Nail fixing (Bag of 50) Size Model Part No. 15mm HX65/15 P-51265 22mm HX65/22 P-51365 PIPE CUTTER PIPE CUTTER Up to 28mm Pipe. Ratchet type HD78. Part No. P-51053 Designed for DIY user. Scissor type HD74. Part No. P-51052 SILICONE LUBRICANT 125gm Tub S254 Part No. P-51051 DEMOUNTABLE BiTite™ FITTINGS STRAIGHT CONNECTOR EQUAL TEE Size 15 x 15mm 22 x 22mm 28 x 28mm Size 15 x 15 x 15mm 22 x 22 x 22mm 28 x 28 x 28mm Model HD1/15 HD1/22 HD1/28 Part No. P-51201 P-51301 P-51401 SOCKET REDUCER Size 15 x 10mm 22 x 15mm 28 x 22mm Model HD2/15 HD2/22 HD2/28 Part No. P-51202 P-51302 P-51402 EQUAL ELBOW Size 15 x 15mm 22 x 22mm 28 x 28mm Model HD5/15 HD5/22 HD5/28 Part No. P-51205 P-51305 P-51405 STRAIGHT TAP CONNECTOR With brass nut and fibre washer Size Model 1 ⁄2 " x 15mm HD25A/15 3 ⁄4 " x 15mm HD25B/15 3 ⁄4 " x 22mm HD25B/22 Part No. P-51225A P-51225B P-51325 BENT TAP CONNECTOR Size 1 ⁄2 " BSP x 15mm Model HD27/15 Part No. P-51227 DEMOUNTABLE STOP END New white plastic Size 15mm 22mm Model HD62/15 HD62/22 Part No. P-51207 P-51208 All BiTite™ Hep2O fittings are fully compatible with Hep2O pipe & copper pipe. SEE SECTION 1 FOR COPPER PIPE. Model HD10/15 HD10/22 HD10/28 Part No. P-51210 P-51310 P-51410 END REDUCED TEE Size 22 x 15 x 22mm 28 x 22 x 28mm Model HD12/22 HD12/28 Part No. P-51312 P-51412 BRANCH REDUCED TEE Size 15 x 15 x 10mm 22 x 22 x 15mm Model HD13/15 HD13/22 Part No. P-51213 P-51313 BRANCH & ONE END REDUCED TEE Size 22 x 15 x 15mm 28 x 22 x 22mm Model HD14/22 HD14/28 Part No. P-51314 P-51414 TANK CONNECTOR With BSP tail and back nut (cold only) Size Model Part No. 1 ⁄2 " BSP x 15mm HX20/15 P-51220 3 ⁄4 " BSP x 22mm HX20/22 P-51320 See page 53 for Hep2O Polybutylene Pipe. Same great pipe – now in white. CATALOGUE SUPPLEMENT - H 55 Water Filters, Wastes, Accumulator Tanks, Jerry Cans, Gland Packing PLUMBING - MISCELLANEOUS DOULTON WATER FILTER CARTRIDGES & HOUSING The small and complex pore structure of Doulton® ceramics makes them an ideal filter medium for drinking water. High Efficiency Filter: Capable of removing more than 99.99% of pathogenic bacteria, particles and disease causing cysts such as Cryptosporidium and Giardia. Long Life/Value for Money: The outer shell of Doulton® ceramic drinking water filters may be cleaned to prolong the life of the product, meaning the filter can be re-used rather than replaced, giving a much longer life-span and saving you money. On average, the filter candle will remain effective for at least 6 months (depending on usage) before it will need to be replaced. Anti-Bacterial Action: Contains a proprietary system to inhibit microbiological growth, meaning that there is no need to sterilise the filter. Retains Essential Minerals: Allows essential minerals to remain in the water which benefits your health. No Power Required: Does not require electricity to function so cost-effective to run, not vulnerable to interruption of power supplies and can be used when no power available. Part No. 9-19989 9-19997 9-19998 Description Doulton HIP Water Filter c/w sterasyl 10'' ceramic cartridge Inline Water Pre-filter housing c/w spun poly cartridge Doulton Sterasyl 10'' ceramic filter cartridge 9-19997 9-19989 • Bottled water quality on tap on your boat • No power required – low running costs • Eco-friendly, reusable filter cartridges • 175 years experience – a proven brand you can trust • Long-life filters – great value for money 9-19998 • Simple to install, use and maintain ACCUMULATOR TANKS (Expansion Vessels) BASIN WASTE Suitable for potable water made in non-toxic powder coated steel with a fixed butyl diaphragm. Can be fitted to threaded tee pieces or tee for compression fitted pipe (see Section 1). Fitted with pressure valve. Technical Specifications: Capacity: 2 litres 5 litres Diameter: 120 mm 170 mm Height: 240 mm 275 mm 1 3 Pipe connection: ⁄2 " BSPM ⁄4 " BSPM Max working pressure: 10 bar 10 bar Working temp.: -10 to 100ºC -10 to 100ºC Colour Finish: Grey Grey Part No.: 9-40302 9-40303 Chrome plated brass 11⁄4 '' straight waste with captive flip plug (plug rotates in body). Part No. 9-68065 SINK WASTE Chrome plated brass 3 ⁄4 '' straight waste with brass backnut & plug. Part No. 9-68066 ENGINE ROOM CAN-SB PLASTIC FUEL JERRY CANS Part No. Ltrs 2-20115 5 2-20116 10 2-20117 20 2-20115 2-20117 2-20116 GLAND PACKING Made from quality yarn lubricated & graphited prior to plaiting. Suitable for stern glands , pumps etc. Supplied as 8M length or if possible carded. 56 Section 8m Part No. 1 ⁄4 " (6.5mm) 2-03012 5 ⁄16 " (8mm) 2-03013 3 ⁄8 " (10mm) 2-03014 1 ⁄2 " (13mm) 2-03015 3 ⁄4 " (20mm) 2-03011 0.5m Cut Part No. 2-03012/1 2-03013/1 2-03014/1 – – CATALOGUE SUPPLEMENT - H 0.5m Carded Part No. 2-03012P 2-03013P 2-03014P – – H (mm) 260 375 220 W(mm) 265 265 370 L(mm) 145 145 380 ANTI-SYPHON LOCK WITH VALVE Anti-syphon valve for liquid cooled engines to connect on the exhaust line. Multiple hose size connections Diameters: 13 to 38mm Height (A): 158mm (61⁄4'') Width (B): 305mm (12'') Part No. 2-20295 B B A A Weight 1.75kg 2.5kg 3.2kg Johnson Pump Pumps, Blower & Tank PLUMBING - PUMPS AQUA JET WPS 3.5 PUMP WITH BYPASS Model: Length: Width: Height: Weight: Motor: Body: Valves: Diaphragm: Connection: WPS 3.5 fitted with a built-in pulsation dampening by-pass to control unwanted cycling and noise. The five chamber Aqua Jet WPS Series provides a reliable heart for small boat and recreational vehicle water pressure system. It’s lower initial price is naturally attractive, but equally important, its readily serviceable design assures low maintenance costs and years of faithful service. It’s recommended to install an accumulator tank. Also available: Always use a PUMProtector inlet strainer before Aquajet Pump Pressure Switch with the pump intake. Bypass (2.8b). Part No. 09-47277 See our catalogue Section 10 for the full range or visit our website: www.aquafax.co.uk. Model WPS 3.5 Capacity 13LPM (3.5GPM) Cut-Off Pressure 12V Part No. Fuse Size 2.1bar/30psi 10-13395-07 10A WPS 3.5 236.5mm 210mm 116mm 2kg 85W PP/PPA EPDM Santoprene 3 ⁄8" BSP/hose 1⁄2", 1 ⁄2" BSP/hose 3⁄4" 24V Part No. 10-13395-08 Fuse Size 5A Specification: Capacity: Voltage: JOHNSON PUMP HEAVY DUTY RADIAL BLOWER 280m3/hr 163cfm 12V Amps: 3.9A 24V Amps: 2.5A Dimensions: H: 290 x W: 257 x L: 180mm Port Connections: Inlet: 75mm Outlet: 72mm • Designed for engine compartment ventilation prior to start-up • Motor rated for continuous operation and can be used as air intake or extraction to ventilate bilges, galleys, accommodation and other compartments • Flange mount design • Double ball bearing motor with corrosion resistant stainless steel shafts and screws Description Air 3'' 90º Bilge Blower 12V Air 3'' 90º Bilge Blower 24V Part No. 10-47416-01 10-47416-02 JOHNSON PUMP VIKING COMPACT MANUALLY OPERATED BILGE PUMP The Viking Compact is a bulkhead fitting, manually operated, self-priming, diaphragm pump designed for bilge pump applications on boats. Complies with ISO 15083 Small craft - bilge pumping systems. Can be used on boats of design categories A, B, C and D. Specification: Plastic materials: Elastomers: Shafts: Connections: ABS, PA 66, PP Nitrile rubber Stainless Steel 25mm (1") or 38mm (11⁄2 ") hose connections Max. Liquid temp.: +60ºC (140ºF) Storage temp.: -40ºC to +60ºC (-40ºF to 140ºF), without operation and in dry condition Dimensions: According to fig.1 Weight: 0.7kg (1.54lbs) CAPACITY Output capacity depends on installation conditions and pumping rate. Performance given at back pressure (head) of 10kPa (1.45psi) rated for 45 strokes per minute: Dia. 38mm (11⁄2 ") ports, 37.5 lit/min (9.91 USGPM) (594 USGPH). Maximum lift: 2.1m (7') Maximum head: 1.2m (4' ) Maximum combined lift and head: 3.3m (11') Description Viking Compact w. dia 25mm (1") and dia. 38mm (11⁄2 ") ports Part No. 10-24800-01 JOHNSON PUMP GREY WATER TANK • Designed for use as a waste water collection tank from showers, sinks, dishwashing machines etc. • Easy access cover for cleaning • Available with Ultima Switch for automatic operation to any 12/24V pump rated up to 20A Shows tank • Tank is prepared for Viking Power 16 waste pumps with pump 10-13350-03/04 (not included) • Hose Connections: Inlet: 3 x 19mm, 3 x 25mm 3 x 38mm Outlet: 1 x 19mm, 1 x 25mm • Dimensions: 185 x 280 x 340mm • Capacity: 10L 10-1206 Description Multiple Port Grey Water Tank c/w Ultima 12/24V Switch Multiple Port Grey Water Tank Only Part No. 10-1206 10-1207 CATALOGUE SUPPLEMENT - H 57 Lewmar CPX Windlass SAILING CPX VERTICAL WINDLASS Lewmar has developed a new range of lightweight vertical windlass to compliment the current V Range. Windlass is one of the largest divisions of Lewmar and they are in constant contact with boat designers, boat builders, and owner’s associations to ensure that their products remains at the forefront of development. In response, Lewmar has developed the new CPX Range. • 15% lighter than comparable all-stainless windlass • New architecture with reduced parts • Easier to service • Alloy base • New styling • Customer-focused design • Highly reliable, light weight, high performance windlass • IP68 motor gearbox available on request CPX Gypsy Drum CPX Gypsy Only Part No. L66910364 L66910365 L6672021001* Description CPX 1 Gypsy Only 12V 6mm Kit CPX 1 Gypsy Only 12V 8mm Kit CPX 2 Gypsy Drum 12V 001 Kit *To Order Only Other sizes may be available Tel: 023 8045 4045 for details SPECIFICATIONS Model CPX1 12V CPX2 12V Motor Power Watt 700 700 Max Pull kg lb 454 650 1000 1433 Working Load Limit kg lb 113 163 250 358 Max Line Speed m/min ft/min 19 21 For Foot Switches see Page 9 of the Aquafax Lewmar Catalogue 58 CATALOGUE SUPPLEMENT - H 65 69 Normal Current Draw Amp Circuit Breaker Amp 80 80 90 90 App Weight Gypsy Only kg lb App Weight Gypsy/Drum kg lb 17.5 17.5 20.0 20.5 38.5 38.5 For 285 Series Circuit Breakers see page 46 of Section 8 44.0 45.1 Lewmar HTX Blocks SAILING HTX BLOCKS Years of design and manufacturing experience, combined with collaboration with boat builders, designers, and sailors, has resulted in the new Lewmar HTX Hardware Range. Drawing upon the design of the racing range, the HTX blocks are constructed from a minimal number of alloy parts, providing enhanced reliability. Additional Information Post Diameter: Shackle Pin Diameter: Max Line Size: Fits Traveller Upstand: Fits Block Upstand: Fit Snap Shackle: Working Load Limit: Breaking Load: Size 50 9.4mm (3 ⁄8 ") 5mm (3 ⁄16 ") 10mm (8mm fiddle) 3 ⁄8 '' (5⁄16 '' fiddle) Sz1NTR L19811000* L29926040* 800kg (1760lb) 1600kg (3520lb) • Alloy cheeks • High Load capacity and large line size • Side thrust ball bearings • Head design inspired by Lewmar racing range with swivel head mechanism locking through a grub screw Size 60 11.9mm (15 ⁄32 ") 6mm (1 ⁄4 ") 12mm (10mm fiddle) 1 ⁄2 '' (3 ⁄8 '' fiddle) Sz2NTR L19821000* L29927040 1100kg (2425lb) 2200kg (4850lb) Size 72mm 16.5mm (2 1⁄32 '') 9.8mm (3⁄8 '') 14mm (12mm fiddle) 9 ⁄16 '' (1 ⁄2 '' fiddle) – – – 2000kg (4400lb) 4000kg (8800lb) Size 90mm 19.75mm (7⁄9 '') 10mm (3⁄8 '') 16mm (5⁄8' '') – – – 3500kg (7700lb) 7000kg (15400lb) * see page 54 of Lewmar catalogue Part No. L29195001 L29195002 L29195003 L29195004 L29195005 L29195009 L29195010 L29195021 L29195031 L29195034 L29195037 L29195039 L29195047 L29196001 L29196002 L29196003 L29196004 L29196005 L29196009 L29196010 L29196021 L29196031 L29196034 L29196039 L29196047 L29197201 L29197202 L29197204 L29197221 L29197231 L29197234 L29197237 L29197239 L29197247 L29199001 L29199004 Size 50 50 50 50 50 50 50 50 50 50 50 50 50 60 60 60 60 60 60 60 60 60 60 60 60 72 72 72 72 72 72 72 72 72 90 90 Description Single Double Triple Single Becket Double Becket Single Becket & cam Triple Becket & cam Toghead Single Fiddle Single Fiddle Becket Fiddle & cam Fiddle Becket & cam Single Web/Lash Single Double Triple Single Becket Double Becket Single Becket & cam Triple Becket & cam Toghead Single Fiddle Single Fiddle Becket Fiddle Becket & cam Single Web/Lash Single Double Single Becket Toghead Single Fiddle Single Fiddle Becket Fiddle & cam Fiddle Becket & cam Single Web/Lash Single Single Becket Single Weight g (oz) 139 (4.76) 217 (7.65) 305 (10.76) 150 (5.29) 232 (8.18) 320 (11.29) 511 (18.02) 160 (5.64) 165 (5.82) 175 (6.17) 335 (11.82) 346 (12.20) 80 (2.8) 215 (7.58) 331 (11.67) 426 (15.03) 226 (7.97) 319 (11.25) 414 (14.60) 710 (25.04) 227 (8.01) 257 (9.06) 269 (9.49) 460 (16.22) 148 (5.2) 445 15.70 552 19.47 482 17.00 410 14.46 530 18.69 560 19.75 748 26.38 776 27.37 735 25.92 936 33.01 Double Triple Single Fiddle Single Becket CATALOGUE SUPPLEMENT - H 59 The Aquafax Catalogue 2 Plastic Seacocks & Pipe Fittings 3 4 Paints, Sealants & Consumables 5 General Boat Equipment and Accessories 6 7 Electrical - Batteries, Cables, Terminals, Chargers & Inverters 8 Calorifiers, Toilets, Pumps, Taps, Sinks & Fittings 9 1 Hull & Engine Room Fittings Ultraflex Controls & Steering Cabin Fittings, Hinges, Padlocks, & General Hardware Valves, Pipe Fittings, Gas Equipment, Hose & Clips Johnson Pump Engine Cooling, Bilge, Deckwash & Macerators 10 Mastervolt Electricals Complete Systems M Lewmar - Windlasses, Anchors, Thrusters, Winches, Hardware & Steering L We offer over 16,000 quality marine and industrial products from all around the world. www.aquafax.co.uk Narrowboat Equipment 60 NB Our range can be viewed online or in the Aquafax printed catalogues. CATALOGUE SUPPLEMENT - H