MLM MedialLink_206_revF.PMD

im Vertrieb von
CAMBOARD Electronics
MediaLink™ Mounting Options Installation Guide
This guide details how to install the following Extron MediaLinkTM Mounting
Options faceplates, designed for use with an MLC 206 controller.
•
MLM 206 LAAP, a 3.15" H x 10.00" W (8.0 cm H x 25.4 cm W) lectern/
furniture-mounting faceplate with four single-space AAP openings:
#60-389-02 (black), #60-389-03 (white), 60-389-05 (RAL9010 off-white)
DISPLAY
POWER
VOLUME
MAX
MIN
Extron
MediaLink
MLM 206 LAAP
This faceplate replaces the MLM-LAAP.
•
MLM 206 7GWP, a seven-gang (4.50" H x 13.57" W [11.43 cm H x
34.46 cm W]) faceplate with eight single-space AAP openings. This plate can
be mounted to a mud ring, an Extron Surface Mount Box (#60-645-02 or -05),
an Extron External Wall Box (#60-689-02, -03, -05), or a standard electrical
box: #70-373-02 (black), #70-373-03 (white), #70-373-05 (RAL9010 off-white)
DISPLAY
POWER
VOLUME
MAX
MIN
Extron
MediaLink
MLM 206 7GWP
Controllers and AAPs are not included with any of the faceplates.
Replacing the MLC 206 Faceplate with an MLM Faceplate
1.
Use a small Phillips screwdriver to remove the four faceplate attachment
screws marked 1 in the picture below, and save them for later use.
1
1
DISPLAY
POWER
VCR
DVD
Laptop
VOLUME
MAX
MIN
1
1
Extron
MLC 206
Do not remove these screws while the MLC 206 is installed in a wall or
furniture, or the controller may fall down into the wall/furniture or wall box.
68-621-01 Rev. F
01 05
www.camboard.de
Tel.MediaLink
07131 911201
[email protected]
™
Mounting Options
• Installation Guide
1
Fax 07131 911203
im Vertrieb von
CAMBOARD Electronics
MediaLink™ Mounting Options Installation Guide, cont’d
2.
Lift the faceplate off the MLC 206.
Plastic Window
Faceplate
AY
PL R
DISWE
PO
ink
Me
L
dia
E
M
LU
VO
X
MA
MIN
Ex
tro
n
Remove four screws.
3.
Align the openings in the new MLM faceplate with the controller’s buttons,
knob, and LEDs, and place the new faceplate on the MLC, as shown above.
4.
Replace the four screws removed in step one, and hand tighten them.
5.
Install the MLC 206 MediaLink controller in a wall or furniture as
appropriate. If necessary, use one of the cutout templates in this guide to
create an opening in the installation surface of a lectern or other furniture.
Templates
Use the appropriate template on the next 2 pages as a guide to measure and mark
the hole in the wall or furniture for installing the faceplate with an MLC 206.
The templates are not to scale and are provided for reference only.
The controller requires a depth of at least 1.5" (3.8 cm) inside the wall or furniture.
www.camboard.de
07131Guide
911201
2
MediaLink™ Mounting OptionsTel.
• Installation
Fax 07131 911203
[email protected]
im Vertrieb von
CAMBOARD Electronics
3.15"
(8.0 cm)
2.9"
(7.4 cm)
8.9"
(22.6 cm)
Top Panel
10"
(25.4 cm)
SURFACE CUT-OUT
AREA FOR
FURNITURE MOUNT
Location of MLC 226
To install MLC 206
and MLM 206 LAAP
directly into furniture,
cut along this line.
.250" (1.00 cm)
.295" (1.16 cm)
TEMPLATE IS NOT FULL SIZE.
Cut-Out Template for Extron's MLM 206 LAAP
www.camboard.de
Tel.MediaLink
07131 911201
[email protected]
™
Mounting Options
• Installation Guide
3
Fax 07131 911203
im Vertrieb von
CAMBOARD Electronics
MLM 206 7GWP
4.5"
(11.4 cm)
2.9"
(7.4 cm)
Top Panel
13.57"
(34.46 cm)
Location of MLC 206
12.9"
(32.77 cm)
SURFACE CUT-OUT
AREA FOR
FURNITURE MOUNT
To install MLC 206
and MLM 206 7GWP
directly into furniture,
cut along this line.
TEMPLATE IS NOT FULL SIZE.
Cut-Out Template for Extron's MLM 206 7GWP
www.extron.com
Extron Electronics, USA
Extron Electronics, Europe
Extron Electronics, Asia
Extron Electronics, Japan
1230 South Lewis Street
Anaheim, CA 92805
USA
714.491.1500
Fax 714.491.1517
Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
+31.33.453.4040
Fax +31.33.453.4050
135 Joo Seng Road, #04-01
PM Industrial Building
Singapore 368363
+65.6383.4400
Fax +65.6383.4664
Kyodo Building
16 Ichibancho
Chiyoda-ku, Tokyo 102-0082 Japan
+81.3.3511.7655
Fax +81.3.3511.7656
www.camboard.de
4
Tel. 07131 911201
Fax 07131 911203
© 2005 Extron Electronics. All rights reserved.
[email protected]