Moroccan Spice

Transcription

Moroccan Spice
Assembly Line Cardmaking
November 2015 Greetings to Go
Moroccan Spice
Moroccan Spice Materials:
□ Greetings to Go
Tools and Supplies:
□ Scor-Pal®
□ Adhesive
□ Tape
□ Foam Adhesive
□ Paper Trimmer
□ 3x14” CS® Grid Ruler
□
□
□
□
□
□
Scissors
Paper Piercing Tool and Cork Board
Craft Knife and Cutting Mat
CS® Glue Pen
Stapler and Staples
Wire Cutter or Serrated Scissors (Optional)
Preparation:
1. Trim the Ivory and Kraft printed cutaparts into sections as indicated by the artwork.
2. Scoring and folding information is listed within the instructions for each card set.
3. If you do not have an item to complete the card as shown, simply omit or substitute the item.
4. CS® Earth ink has been applied to the edges of some cutaparts, cards and panels, but instructions to do
so are not included below.
All rights reserved. ©2015, Club Scrap, Inc.
(888) 634-9100 • www.clubscrap.com • email: [email protected]
November 2015 • Moroccan Spice Greetings to Go • Page 2 of 4
Set A: 4¼x5½” Gold Cards with 4x5¼” Purple Panels
Score and fold each 5½x8½” Gold card horizontally at 4¼”.
Notes: Cut a slot for the ribbon on the left and right edges of the
shape on the Ivory cutapart; thread with gold ribbon and tape
ends on the back; remove the prongs from the brad and adhere;
nest the cutapart and panel onto the card; staple red ribbon to the
“You are the best!” cutapart and attach to the inside of the card.
Notes: Cut a slot for the ribbon on the left and right edges of the
shape on the Ivory cutapart; thread with gold ribbon and tape
ends on the back; remove the prongs from the brad and adhere
to the shape; nest the cutapart and panel onto the card; affix the
“And smiling about it” cutapart to the inside of the card.
Notes: Cut a slot for the ribbon above and below the “with
sympathy” strip printed on the Ivory cutapart; layer red ribbon onto
the gold ribbon and slide beneath the strip; secure ribbon ends on
the back; remove prongs from the brads and glue to the left and
right of the greeting; nest the cutapart and panel onto the card;
adhere the Ivory “Our thoughts are with you” cutapart to the inside
of the card.
Notes: Wrap red ribbon around the Ivory
cutapart just above the printed greeting;
remove the prongs from the brad and attach
above the ribbon; nest the cutapart and
panel onto the card; adhere the Kraft “Enjoy
your special day” cutapart to the inside of
the card.
©2015, Club Scrap, Inc.
(888) 634-9100 • www.clubscrap.com • email: [email protected]
November 2015 • Moroccan Spice Greetings to Go • Page 3 of 4
Set B: 5x7” Brown Cards with (2) 2¼x6¾” Red, 4½x6½” Kraft and 2x2” Brown Panels
Score and fold each 7x10” Brown card horizontally at 2½ and 7½”.
Notes: Adhere the Red panels to the
Brown card flaps and attach the White
cutaparts to the upper center, flush with the
inside edges of the Red panels; wrap the
1x11” Kraft cutapart around the card and
attach ends; make a red ribbon loop and
tape to the back of the Ivory “miss you”
cutapart; layer onto the Brown panel and
attach to the Kraft band; staple red ribbon
onto the Ivory “Just saying hi” cutapart;
adhere to the Kraft panel and center onto
the inside of the card.
Notes: Follow the same assembly
process to make the remaining three
cards; staple red ribbon to the Ivory
“Sending a hug your way” cutapart
and attach to the inside Kraft panel.
Notes: Adhere the Ivory “Hoping
your day is amazing” cutapart to the
Kraft panel on the inside of the card.
Notes: Staple folded red ribbon to
the Ivory “You're amazing” cutapart
and attach to the inner Kraft panel.
©2015, Club Scrap, Inc.
(888) 634-9100 • www.clubscrap.com • email: [email protected]
November 2015 • Moroccan Spice Greetings to Go • Page 4 of 4
Set C: 3½x5” Green Easel Cards with 3¼x4¾” and 2x3¼” Brown Panels
Score and fold each 3½x10” Green Card horizontally at 5 and 8”.
Notes: The assembly process for all four cards in this set is the same. Tie a bow with gold ribbon and adhere
to the top of the Ivory or Kraft cutapart; nest onto the 3.25x4.75” Brown panel; attach the Brown panel to the
bottom scored 3” area of the Green card base to allow the easel to function; nest the Ivory or Kraft greeting
onto the 2x3.25” Brown panel and attach to the bottom of the inside of the card.
©2015, Club Scrap, Inc.
(888) 634-9100 • www.clubscrap.com • email: [email protected]