R04.4
Transcription
R04.4
Chemisch Beständige Radialventilatoren Chemical Resistant Centrifugal Plastic Fan R04.4 # & Symbole und Formelzeichen Symbols and technical formula symbols Symbol Symbol Bedeutung / Meaning Symbol Bedeutung / Meaning , 5-Stufen-Steuergerät, transformatorisch 5-step transformer control . Drehzahlumschalter Speed control switch 5 Schaltplan Wiring diagram + Steuergerät, stufenlos, transformatorisch Continuously adjustable transformer control - Geräteausschalter Off-Switch ( explosionsgeschützt flame proof Steuergerät, stufenlos, elektronisch Continuously adjustable electronic control ) Gewicht Weight Motorschutzschalter Motor protection switch 4 Schutzart Protection class * / II Bedeutung / Meaning 7 6 Abmessungen Dimensions Zubehör Accessories Größe Symbol Benennung Designation Einheit Unit A Querschnittsfläche Cross-section m² c Strömungsgeschwindigkeit Flow speed m/s C400V Betriebskondensator Capacitor µF D2 Durchmesser des Laufrades Impeller diameter m d Rohrdurchmesser Pipe diameter m dg gleichwertiger Durchmesser Equivalent diameter m Freq Spannungssteller Frequency Invertor Speed Controller - g Fallbeschleunigung Gravitational speed acceleration m/s² IN Nennstrom Rated current A IA / IN Verhältnis Anlaufstrom zu Nennstrom Ratio of starting current to rated current DI Stromanstieg bei Teilspannung Current increase in component voltage area % l Rohr- bzw. Kanallänge Pipe or channel length m LPA A-bewerteter Schalldruckpegel Sound pressure level A-weighted dB(A) LWiA A-bewerteter Schalleistungspegel Sound power level A-weighted at inlet dB(A) LWA2 Schalleistungspegel zur Umgebung Sound power level to surrounding dB(A) LWA3 Ansaugkanalschalleistungspegel Inlet sound power level induct dB(A) LWA4 Ausblaskanalschalleistungspegel Outlet sound power level induct dB(A) LWA5 Freiansaug-Schalleistungspegel Inlet sound power level unducted dB(A) LWA6 Freiausblas-Schalleistungspegel Outlet sound power level unducted dB(A) n Drehzahl Speed 1/min (bzw. 1/s) P1 Motoraufnahmeleistung motor power consumption kW (bzw. W) pst (pfa) statischer Druck Static pressure Pa ∆ pst Differenz der statischen Drücke Differential static pressure Pa D pfa min erforderlicher statischer Mindestgegendruck min. required counter pressure Pa pd dynamischer Druck Dynamic pressure Pa pd2 dynamischer Druck am Ventilatoraustritt Dynamic pressure at fan outlet Pa ∆ pd Differenz der statischen Drücke Differential dynamic pressure Pa pt Gesamtdruck Total pressure Pa ∆ pt Differenz der Gesamtdrücke Difference of total pressures Pa T Kelvin-Temperatur Temperature in Kelvin K t Celsius-Temperatur Temperature in Celsius °C tR max. zulässige Fördertemperatur max. permissable medium temperature °C u2 . V Umfangsgeschwindigkeit des Laufrades (außen) Circumferential speed of the impeller (outside) m/s Volumenstrom Volume flow m³/h (bzw. m³/s) ρ Dichte des Fördermediums Density of medium kg/m³ η Wirkungsgrad Efficiency - ϕ Volumenzahl Volume number - ψ Druckzahl Pressure number - ζ Widerstandsbeiwert Coefficient of drag - λR Rohr- bzw. Kanalreibungsbeiwert Coefficient of friction of channel or pipe - R04.4 V2014/April # Inhaltsverzeichnis Technische Informationen Contents Technical Information Inhaltsverzeichnis Contents Technische Informationen Technical information Ventilatorkurven Fan curves Schallangaben Sound information 27-28 Abmessungen Dimensions 29-37 Auf-und Einbau Assembly and mounting 38-44 Ausschreibungstexte Specification 45-50 R04.4 V2014/April 1 2-5 6-26 1 # Technische Informationen Technical Information CHEMCO chemisch widerstandsfähige Kunststoff-Lüfter CHEMCO CHEMICAL RESISTANT PLASTIC FAN CHEMCO = chemical resistant plastic fan CHEMCO = chemical resistant plastic fan Rolle Role Chemco spielte ein führende Rolle bei der Herstellung von Gegenständen aus nicht rostenden und chemisch widerstandsfähigen Kunststoffen. Diese Geräte sind bestens geeignet für Belüftungs- & LärmbekämpfungsSysteme, Reinraumtechnik, Galvanisier-Anlagen, Laboratoriums-Abflüsse & Behälter, Bürsten, Wasserspeicher und kundenspezifische Systeme. Chemco has played a leading role in the manufacturing of equipment made from anti-corrosive and chemical resistant plastics. These equipment are most suitable for use in the ventilation & noise control systems, clean rooms engineering, plating equipment, laboratory sinks & containers, scrubbers, tank constructions as well as custom design systems. Erfahrung Experience Aufgrund der langjährigen Erfahrung und Know-How im Kunststoffbereich, war es Chemco möglich ein komplette Baureihe von nicht rostenden Ventilatoren zu entwickeln. Die Ventilatoren zeichnen sich durch einen hohen Wirkungsgrad, zuverlässiges Betriebsverhalten und hervorragende Korrosionsfestigkeit aus. Grundmerkmale sind ebenso die einfache Wartung und die Wirtschaftlichkeit. The years of experience and know-how in the areas of plastics, its designing capability enables Chemco to develop a complete range of anticorrosive fans. The fans are specially designed for high efficiency, reliability, with superior corrosion resistance quality. They are also developed to give trouble-free service, and are economical in use. Anwendung Application Chemco korrosionsbeständige Kunststoff-Ventilatoren sind speziell enwickelt um schwerkorrosive Rauchgase, Dämpfe, verseuchte Luft und aggressive Gase zu handhaben. Solche Ventilatoren eignen sich zum Gebrauch im Prüflabor, Krankenhaus, Nahrungsmittelindustrie, Elektronikindustrie, chemisch und galvanische Metallbeschichtungs-Gewerbe, Reinraumtechnik usw. oder auch für die Luftaufbereitung in der Bauindustrie. Chemco corrosive resistant plastic fans are specially developed to handle heavy corrosive fumes, vapours, contaminated air and aggressive gases. Such fans are suitable for use in the test laboratory, hospital, food industry, electronic industry, chemical and electroplating industry, clean rooms engineering etc. They are also suitable for air conditioning application in the building industry. Gütegrad Quality Chemco bietet eine komplette Baureihe wirkungsvoller rückwärtsgekrümmter Radialventilatoren hoher Qualität mit sehr guter Leistung und niedrigem Geräuschpegel. Alle Ventilator-Antriebe und Zubehöre werden nach genauen Qualitätsstufen hergestellt. Es kommen nur Qualitäts-Werkstoffe zum Einsatz und alle Ventilatoren sind erprobt und geprüft nach DIN 24163, ISO 5801 und AMCA 210. Chemco supply a complete range of highly quality and efficient radial tip backward curve fans, which offer an excellent performance with a low noise level. All fans drive and accessories are produced to strict quality standards. Only the best quality materials are used and all fans are tested and rated in accordance with DIN 24163, ISO 5801 and AMCA 210. Erzeugnisse und Leistung Products and Performance Chemco Radial-Ventilatoren und Dachventilatoren mit horizontalem oder senkrechtem Ausblas bieten Leistungen von bis zu 180.000 m³/h und statischem Druck von bis zu 7.000 Pa. Thermoplastische Kunststoffe wie PP, PE, PVC, PVDF oder GFK die Widerstandsfähigkeit gegen die meisten Chemikalien bieten sind verfügbar. Chemco centrifugal fans and roof fans with horizontal or vertical outlet have performance capacity of up to 180,000 cmh and operating at a static pressure of up to 7,000 Pa. Thermoplastic materials such as PP, PE, PVC, PVDF or GRP that offer the best guarantee to resist most chemicals are available. Schallpegel Sound Level Um eine Bewertung entsprechend dem menschlichen Gehör zu ermöglichen wurde die A-bewertete Beschreibung des Schallpegels gemäß DIN 45635 gewählt. Die Schallmessung erfolgt mit dem Hüllflächenverfahren gemäß DIN 45635 Teil 38 oder dem Kanalverfahren DIN 45635 Teil 9 oder AMCA 300. In order to make possible an assessment of sound projection adequate to human ear the A-assessed description of sound level according to DIN 45635 has been chosen. The ascertaining of the sound power level follows the enveloping surfaces method according to DIN 45635 section 38, section 9 or AMCA 300. Dongguan Wolter Chemco Ventilation Ltd. certifies that the series CHEM shown herein are licensed to bear the AMCA Seal. The ratings shown are based on tests and procedures performed in accordance with AMCA Publication 211 and AMCA Publication 311 and comply with the requirements of the AMCA Certified Ratings Program. CHEM 75R to 180 are not licensed to bear the AMCA certified Ratings Seal. The AMCA Certified Ratings Seal applies to air and sound performance for Model CHEM 200 to CHEM 1250. CHEM 75 - 110 CHEM 125 - 200 2 Standardbaureihen und Ausführungen Standard Models and Designs Typ CHEM 75-315 DD Model CHEM 75 DD to 315 DD - mit Direktantrieb - Kunststoff Spritzgußgehäuse standardmäßig aus PP - CHEM 125 to 200 gehäuse passend für beide Drehrichtungen, montiert auf verzinktem Stahl-Bock, mit angeflanschtem Normmotor - Laufrad fliegend auf Motorwelle montiert - Ventilator-Bock mit Stützwinkeln - With direct drive - Plastic injection moulded casing with PP as standard. - CHEM 125 to 200 casing suitable for dual rotations mounted on the galvanised steel support comes with flanged standard motor - Impeller mounted overhung on the motor shaft. - Fan base with angle support R04.4 V2014/April Technische Informationen Technical Information Typ CHEM 125-315 BD # Model CHEM 125 BD to 315 BD - mit Riemenantrieb - Kunststoff Spritzgußgehäuse standardmäßig aus PP. - CHEM 125 to 200 gehäuse passend für beide Drehrichtungen. Gehäuse passend für beide Drehrichtungen, montiert auf verzinktem StahlBock, Doppel-Flanschlager aus Gußaluminium - Laufrad fliegend auf Welle montiert - Ventilator-Bock mit Kanal-Lagerung und Motormontageplatte. - With belt drive. - Plastic injection moulded casing with PP as standard. - CHEM 125 to 200 casing suitable for dual rotations. Casings are mounted on the galvanised steel support come with aluminium cast flanged-on twin bearing housing. - Impeller fixed overhung on the shaft. - Fan base with channel support include motor mounting plate. Typ CHEM 400 DD Model CHEM 400 DD - mit Direktantrieb - Glasfaserverstärkt (GFK/FFK) - Gehäuse mit angeflanschtem Normmotor, montiert auf verzinktem Stahl-Bock - Laufrad fliegend auf Motorwelle montiert - Ventilator-Bock mit Stützwinkeln - With direct drive - Glass-Reinforced Plastic (GRP/FRP) casing - Casing mounted on the galvanised steel support comes with flanged standard motor. - Impeller mounted overhung on the motor shaft. - Fan base with angle support Typ CHEM 400 BD Model CHEM 400 BD - mit Riemenantrieb. - Glasfaserverstärkt (GFK/FFK) - Gehäuse montiert auf verzinktem Stahl-Bock, Doppel-Flanschlager aus Gußaluminium - Laufrad fliegend auf Welle montiert - Ventilator-Bock mit Kanal-Lagerung und Motormontageplatte - With belt drive. - Glass-Reinforced Plastic (GRP/FRP) casing - Casing mounted on galvanised steel support comes with aluminium cast flanged-on twin bearing housing. - Impeller fixed overhung on the shaft. - Fan base with channel support include motor mounting plate Typ CHEM 450-710 DD Model CHEM 450 DD to 710 DD - mit Direktantrieb. - Gehäuse als maschinell geschweißte Kunststoff-Konstruktion oder aus glasfaserverstärktem Kunststoff (GFK/FFK) - Gehäuse an verzinktem Lagerbock montiert, mit Norm-Fußmotor - Laufrad fliegend auf Motorwelle montiert - Ventilator-Bock mit Kanal-Lagerung - With direct drive. - Casing in plastic mechanically welded construction or Glass-Reinforced Plastic (GRP/ FRP) - Casing mounted on galvanised steel support come with foot mounted standard motor. - Impeller mounted overhung on the motor shaft. - Fan base with channel support Typ CHEM 450-1250 BD Model CHEM 450 BD to 1250 BD - mit Riemenantrieb. - Gehäuse als maschinell geschweißte KunstoffKonstruktion oder aus glasfaserverstärktem Kunststoff (GFK/FFK) - Gehäuse an verzinktem Lagerbock montiert, Welle mit Pendelkugel-Stehlager - Laufrad fliegend auf Welle montiert - Ventilator-Bock mit Kanal-Lagerung und Motormontageplatte - With belt drive. - Casing in plastic mechanically welded construction or Glass-Reinforced Plastic (GRP/ FRP) - Casing mounted on galvanised steel support frame come with "pedestal" mounted selfaligning ball bearing units. - Impeller fixed overhung on shaft. - Fan base with channel support include motor mounting plate Bei allen CHEM ist das Laufrad standardmäßig aus PP oder GFK G1 und G3 . Das CHEM 400-1250Ventilatorgehäuse gewöhnlich aus GFK/ FFK, bietet gute Säure- und Laugenfestigkeit. Es kann ebenso mit Einlagen vermischt werden um Anforderungen an Hochtemperatur-, UVBeständigkeit oder Schutz vor elektrostatischer Entladung zu genügen. Je nach Kundenwunsch. All CHEM impeller come with PP as standard, GRP G1 and G3 as optional. CHEM 400 to 1250 fan casing usually of GRP/FRP material, good for chemical resistance, can also be blended with composites to withstand high temperature, flame retardant, UV or Electrostatic Discharge protection to suit customer's requirements. Standard Farben Standard Colour sämtliche PP - entsprechend PANTONE warm grau 1C, sämtliche GFK - entsprechend PANTONE 430 Andere Farben wenn erforderliche. All PP - Equivalent to PANTONE Warm Grey 1C, All GRP - Equivalent to PANTONE 430 Other colours as optional requirement. Sicherheitstechnische Besonderheiten Safety Features Sämtliche Riementriebe, Scheiben, vorstehend Stellschrauben, Keile und andere rotierende Teile haben Verkleidungen aus strapazierfähigem perforiertem Blech, um sicherheitstechnische Forderungen zu erfüllen. Jeder Ventilator hat ein festmontiertes Typenschild mit Seriennummer und Modellbezeichnung, Lüfter + Antriebsdaten, Luftmenge und Fabrikationsdatum. All drive-belts, pulleys, projecting set screws, keys and other rotating parts have heavy-duty perforated sheet as protective guards to meet safety requirements. All fans are labelled with nameplate securely attached on each fan showing the serial and model number, fan & drive duties, rotation of flow and date of manufacture. CHEM 250 - 315 CHEM 400 CHEM 450 - 710 CHEM 800 -1250 R04.4 V2014/April 3 # Technische Informationen Technical Information Konstruktion der chemisch beständigen Radiallüfter Chemical Resistant Centrifugal Plastic Fan Design Gehäuse Casing Das Ventilatorgehäuse ist entweder aus thermoplastischen Kunststoffen wie PP, PVC, PE, PVDF oder Glasfaserverstärkten Kunststoffen - Vinyl Ester Klasse (GFK oder FFK). Das Ventilatorgehäuse hat die Form einer echten Spirale und hat eine Hochleistungsansaugdüse um eine gleichmäßige LuftVerteilung über die volle Laufradbreite zu erreichen. Die kleineren Gehäuse, Typ CHEM 75 - 315 sind vollständig aus SpritzKunststoff. CHEM 125 - 200 sind in jeder Position geeignet für doppeldreh kann der Kunststoff-Spritzgussplatteoder Einlassabdeckung leicht zum Ändern der Dreh , Wartung und Services entfernt werden. Gehäuse mit gerade Auslaufrundefür die direkte Verbindung zum flexiblen Verbindungs kommen. Standardmaterial des Gehäuse ist PP. Die CHEM 400 Gehäuse sind gewöhnlich aus GFK oder vacuumgeformt und maschinell geschweißt. Die Rückscheibe und Ansaugdüse, beide aus Spritzkunststoff, können für Wartungsarbeiten leicht entfernt werden. Die GFK Ventilatorgehäuse haben einen runden geraden Ausblas passend zur direkten Montage eines elastischen Verbinders. Die Gehäuse der größeren Ventilator-Baureihen (Typen CHEM 450 - 1250) sind standardmäßig aus GFK oder, wenn erforderlich, maschinell geschweißte. Das Chemco Ventilatorgehäuse ist äußerst starr, mit angemessen Dicke, speziell versteift, um Schwingungen oder Poltern während des Betriebes auszuschliessen. Um das Risiko der Korosion zu verringern ist das Gehäuse ist so gebaut, dass sich keine Metallteile im Luftstrom befindlichen. Die Gehäuse können aus GFK oder einem thermoplastisch Material vermengt mit Füllstoffen sein um Anforderungen an Hochtemperatur-, UV-Beständigkeit oder Schutz vor elektrostatischer Entladung zu genügen. Je nach Kundenwunsch. Der Ansaug und Ausblas haben Standard-Durchmesser, welche während der Montage leicht mit passenden elastischen Verbindern angeschlossenen werden können . Alle Gehäuse können am tiefsten Punkt der Spirale mit einem Kondensatablaufstutzen versehen werden. Dies erleichtert das Entwässerung von Kondensat bei Aufstellung im Freien. The fan casing is constructed from thermoplastic such as PP, PVC, PE, PVDF or Glass reinforced plastic -Vinyl ester grade (GRP or FRP). The fan casing is built to a true volute form and has high efficiency inlet cone to give an even distribution of air over the full width of the runner. The smaller range of casing, model CHEM 75 - 315 are completely plastic injection moulded. CHEM 125 - 200 are suitable for dual rotation at any position, the plastic injection moulded backplate or inlet cover can be easily removed for changing of rotation, maintenance and services. Fans casing come with round straight outlet suitable for direct connection to flexible connector. Casing usually with PP as standard. The CHEM 400 casing usually of GRP construction or vacuum-formed and automatic machine welded. The plastic injection moulded backplate can be easily removed for maintenance and services. The GRP fans casing come with round straight outlet suitable for direct connection to flexible connector. For larger range of fans (Models CHEM 450 - 1250), the casing is usually of GRP construction as standard or by mechanically machine welded as when required. Chemco fan casing is extremely rigid with adequate thickness, properly stiffened to ensure it is free of vibration or drumming during operation. The casing is also constructed in a way that no metal parts are situated in the airflow to eliminate the risk of corrosion. Casing can be of GRP or any thermoplastic material blended with composites to overcoming high temperature, flame retardant resistant, ultraviolet or Electrostatic Discharge protection to suit customer's requirements. The inlet and outlet are of standard diameter sizes, which can be easily connected together with flexible connector during installation. All casings can be fitted with drain outlets at the lowest point of the scrolls. This is to facilitate the drainage of condensation build-up or rainwater when installed in the open. Rückwärtsgekrümmte Radiallaufräder Radial Tip Backward Curve Impellers Chemco Lüfterlaufräder sind einflutig mit konstanter Breite (SISW). Die Herstellung erfolgt durch Präzisionsspritzguß mit eingegossener Metallnabe (Typen CHEM 125 - 315) oder maschinell geschweißte (Typen CHEM 400 - 1250). Sie entsprechen höchsten Qualitätsstufen und haben ausgezeichnete aerodynamische Eigenschaften. Als Standard wird PP für das Laufrad verwendet, je nach Einsatzfall können auch Pa, PC, PVC oder PVDF Verwendung finden. Entsprechend den Anforderung des Kunden an Hochtemperatur-, UV-Beständigkeit oder Schutz vor elektrostatischer Entladung können die Laufräder auch aus einem thermoplastisch Material vermengt mit Füllstoffen sein. Jedes Laufrad ist, nach Q2,5 (VDI 2060) oder Gütegrad G2,5 (BS 5625 Teil 1 (1979)), statisch und dynamisch in zwei Ebenen gewuchtet. Die Radnaben sind für die Verwendung von Taper-lock-Naben vorgesehen und sind aus hochwertigen Gußplatten. Dies gewährleistet einen zuverlässigen Lauf auch bei hoher Umfangsgeschwindigkeit. Außer CHEM 75-110 mit festen Stahlbuchse und CHEM 90FC - 110FC sind vorwärts gekrümmten Klinge. Chemco fan impellers are of single inlet Single width (SISW) type. Impellers are of precision plastic injection moulded design with cast-in metal hub (Models CHEM 75 - 315) or mechanically welded construction (Models CHEM 400 - 1250) to highest quality standard with excellent aerodynamic properties. Impeller is usually of PP however, depending on the type of applications; impeller can be made of PA, PC, PVC or PVDF. Impeller can be thermoplastic material blended with composites to overcoming high temperature, flame retardant resistant, ultraviolet or Electrostatic Discharge protection to suit customer's requirements. Each impeller is statically and dynamically balanced in two planes in accordance with Q2.5 of VDI 2060 or Grade G2.5 of BS 5625 Part 1 (1979). The hubs are designed for use with taper-bushes and are made of high-grade cast plates to guarantee high reliability at the high peripheral speeds. Except CHEM 75 - 110 with fixed steel bush and CHEM 90FC - 110FC are of forward curved blade. Ventilatorbock und Lager Fan Base and Support Die Ventilatorenböcke und Grundrahmen sind aus schweren Walzstahlprofilen hergestellt und feuerverzinkt. Dies bietet besten Schutz bei widrigsten Bedingungen. Spezielle Oberflächenbehandlungen sind auf Wunsch möglich. Der Ventilator kann in verschiedene Ausblasrichtungen gedreht werden. The fan supporting steel stands and fan bases are manufactured from heavy gauge mild steel and are hot dipped galvanised to provide maximum protec-tion in the most adverse condition. Special surface treatment can be done on request. Fans can be rotated to suit different discharge directions. Achsenwelle und Lager Drive shaft and bearing Abgedrehte Präzisionswellen nach DIN 17210 - C45 mit einem glatten Anstrich. Beide Wellenenden haben Norm-Durchmesser nach DIN 748, Blatt 1 und Nuten nach DIN 6885, Blatt 1. Die Wellen sind zur Vermeidung von Korrosion chemisch widerstandsfähig beschichtet. Auf Anfrage können auch Wellen aus rostfreiem Stahl geliefert werden. Die riemengetreibenen Ventilatoren der Typen CHEM 125 - 400 besitzen Flanschlager aus Gußaluminium. Die Antriebswelle hat zwei spielfreie Standard-Rillenkugellager mit säurebeständiger Dichtung. Diese Konstruktion sichert störungsfreien Betrieb, ruhigen Lauf und minimale Schwingungen. Für CHEM 450 und größer werden die Antriebswellen mit Bocklager aus Gußeisen auf den Ventilatorbock montiert. Es werden entweder Pendelrollen- oder Pendelkugellager verwendet. All precision solid shafts complying to DIN 17210 - C45 are trued and have a smooth finish. Both shaft ends have as standard feature diameters complying with DIN 748, Sheet 1 and grooved to DIN 6885, Sheet 1. The shafts are chemical resistant coated with protective cover to prevent corrosion. Upon requested, stainless steel shaft can also be provided. CHEM 125 - 400 belt driven fans come with flange mounted aluminium cast bearing housings type. The drive shaft is fitted with two standards antifriction grooved balls bearing unit with acid proof seal. This design ensures trouble-free service, silent operation and minimum vibration. For CHEM 450 and above, the drive shafts are mounted on fan pedestal with cast iron housing of plummer block units. These bearings are of selfaligning heavy-duty ball or spherical roller type. Antriebe Drives Genau gewuchtete Standard-Keilriemen-Scheiben mit Spannhülse, nach ISO 4183-1980. Alle Keilriemen entsprechend ISO 4148. Die Riementriebe werden entsprechend der benötigten Leistungen ausgewählt und korrekt verspannt was lange Standzeiten sicherstellt. Standard pulley drive with taper bush type, accurately balanced and conform to ISO 4183-1980 standards. All Vee belts are conform to ISO 4148. Belt section is selected with correct ratings and tensioning to ensure prolonged usage. 4 R04.4 V2014/April Technische Informationen Technical Information # Motor Motor Je nach Anwendung sind Norm-Motoren von IP44, IP45, IP54 oder IP55 auf Anfrage lieferbar. Bei direktgetriebene Ventilatoren werden B5 Flansch-Motore eingebaut, für riemengetriebene Ventilatoren, B3 Fuß-Motore. Alle Motoren sind vollständig geschlossen und luftgekühlt und erfüllen BS 2613. Die StandardMotoren sind einphasig/dreiphasig, 50/60 Hertz passend für 240/415 oder 220/380 Volt. Andere Spannungen sind auf Anfrage lieferbar. Depending on the application, standard electric driven motor of IP44, IP45, IP54 or IP55 can be supplied upon request. For direct driven fans, motor are usually of B5 flange mounting and for belt driven fans, motor are of B3 foot mounting. All motors are totally enclosed and fan cooled complying with BS 2613. The motors are single/three phase, 50/60 Hz suitable for 240/415 or 220/380 volts standards. All other voltage can be supplied upon request. Tropenfestigkeit Tropicalisation Die Motor-Wicklungen sind mit Harz-Lacken ummantelt, welche den Motor passend für tropische Atmosphären machen. Zusätzlich Behandlungen können durchgeführt werden, wenn Motoren in extreme-tropischer Umgebung arbeiten sollen. Motor windings are coated with resin varnishes, which make the motor suitable for tropical atmospheres. Additional treatment can be carried out where motors are required to operate in severe tropical environments. Explosionsschutz Flameproof Alle Ventilatoren mit Ex-Motoren sind für die folgenden Bereiche zugelassen: 1) BS 4683 Part II certifiziert für die Gruppen IIa und IIb 2)BS 4683 Part IV, mit EXE bezeichnet und passed zum Gebrauch in Bereichen der Zone 1 für die Gruppen IIa und IIb. 3)BS 5000 Part 16 und BS 4683 Part III, mit EXN bezeichnete Typen, passend zum Gebrauchen in Bereichen der Zone 2. EX-Schutz-Bereiche Zone 1 und 2, wenn innerhalb nicht explosionsgefährdeter Bereiche der Temperaturklassen T1-T3 installiert, aber nur unter den folgenden Bedingungen: a)Reduzierung der maximal erlaubten Drehzahl um 20% b)Reduzierung der erlaubt Antriebsleistung PW um 30% c)nur Ventilatoren mit horizontalem Kanal verwenden d)der Ventilator muß mit Schutzgittern ausgestattet sein, die das Hineinfallen oder Angesaugtwerden von Fremdkörpern in den Ventilator wirkungvoll verhindern. All fans mounted with flameproof motors are suitable in the following areas: 1) BS 4683 Part II certified for Groups IIa and IIb 2)BS 4683 Part IV designated EXE and are suitable for use in Zone 1 areas for group IIa and IIb. 3) BS 5000 Part 16 and BS 4683 Part III designated type EXN and suitable for use in Zone 2 areas. Flameproof areas zone 1 and 2, when installed in non-explosion hazardous area for temperature categories T1-T3, but only under the follow conditions: a) the maximum allowed revolutions must be reduced by 20% b) the allowed drive power PW should be reduced by 30% c) only fans with horizontal shafts are to be used d) fans must be equipped with guards to prevent foreign particulars falling in or being sucked in. Inspectionsöffnung/klappe Inspection Door/Cover für Instandhaltung und Wartung. An den Typen CHEM 450 und größer kann auf Anfrage eine Inspectionsklappe angebracht werden. Diese Klappe erfüllt die allgemeinen Sicherheits- und Unfallverhütungsvorschriften, da sie nur unter der Verwendung von Werkzeuge geöffnet werden kann. For servicing and inspection purposes. For model CHEM 450 and above, an inspection cover can be included upon request. This cover is complies in general with safety and accident prevention regulations, as it can only be opened by using tools. Zubehör Accessories - Anbau von Feder-Schwingungsdämpfer - Kondensatablaufstutzen mit Verschluß - Motor, Motorschutz, Spannschlitten -Schienen, Riemenschutz, Riemenantrieb - Lager, Abdeckung für Lager und Welle -Ventilatorgrundrahmen - Ansaugflansch, Ansaugmanschette mit Klemmband - Splitter Schutzhaube. - Anti-vibration spring mounting - Condense water drain socket and plug - Motor, motor guard, slide rails, belt guard, belt drive - Bearing, bearing and shaft cover - Fan and motor support base frame - Inlet flanges, Inlet sleeve with clamping bands - Splinter protection cover. wahlweise - Full range of colour matching - Flame Retardant - High Temperature - Electrostatic Discharge - Anti-static, Static dissipative or Conductive - Ultra Violet - Frequency Invertor Speed Controller - andere Farbe aus der gesamten Farbpalette - flammhemmend - Hochtemperatur - elektrostatische Entladung – Anti-statisch, statisch verlustbehaftet oder leitend - UV-beständig Optional Thermische und chemische Beständigkeit Thermal and Chemical resistant Die Temperatur der Luft oder der Gase dürfen den für den Werkstoff angegeben Wert nicht überschreiten: Werkstoff max. Temp. [°C] PVC 60 PP 80 GFK 100 PVDF 120 Für ein ausführliche Liste der chemischen Anwendung wenden Sie sich bitte an unsere örtliche Vertretungen. The temperature of the air and gases must not exceed that specified for the materials: Material max. Temp. [°C] PVC 60 PP 80 GFK 100 PVDF 120 Please contact our local sales engineers for detailed list of Chemical Application Information. R04.4 V2014/April 5 Kennlinie Kennlinie Fan curve Fan curve & CHEM 75R 20 30 50 200 100 • 300 V [C.F.M.] ρ = 1.2 kg/m3 CHEM 75R 6 = P (Basic Model) = G1 (Enhanced Model) = G3 (Heavy Model) 0.32 kW ∆pt[Pa] 5 80 0.25 kW 1000 900 0.2 kW 800 4 77 0.16 kW 3 700 0.125 kW 600 74 6000 1/min 0.1 kW 500 2 71 80 W Po w er 5000 1/min 60 W 68 I nn er 400 50 W 40 W 300 4500 1/min 65 ∆pt [in.WG] 4000 1/min 32 W 25 W 200 1 0.9 3550 1/min 62 0.8 20 W 16 W 0.6 12.5 W 2800 1/min 0.5 56 10 W 2500 1/min 8W 100 0.4 53 90 2250 1/min 6W 80 5W 70 0.7 3150 1/min 59 50 0.3 2000 1/min 4W 60 1800 1/min 47 3.2 W 0.2 50 Sound Power Level LwiA dB(A) 40 1600 1/min 1400 1/min 30 1250 1/min 0.1 0.09 20 20 30 100 50 0.01 2 3 2 0.02 5 10 3 200 0.03 20 30 5 Im Kennfeld ist der A-bewertere Schallei- A-weighted sound power level LwiA is stungspegel LwiA angegebenen. quoted in the diagram. Schalldruckpegel LPA in 1,5 m Entfernung Sound pressure level LPA at 1,5 m dist. LPA [dB(A)] = LwiA - 14,5 300 100 10 200 300 20 Laufraddurchmesser wheel diameter Schaufelzahl number of blades Gewicht weight Drehzahl maximal speed limit 0.08 • V m3/h • V m3/s 0.1 0.05 50 500 pd2 [Pa] 500 30 125 12 G= 0,1 nmax = 6000 D= C2[m/s] mm z= kg 1/min Fan test test laboratory laboratoryAMCA AMCA210/99 210/99Fig.12, Fig.12,Test TestChamber. Chamber. Performance Performance certified is for is installation for installation type type D - Ducted D - Ducted inlet, inlet, Ducted Ducted outlet.outlet. Performance Power Rating ratings (kW) do not does include not include the effects transmission of appurtenances losses, Performance ratings (accessories-belt cover, do not pulley include & belt). the effects of appurtenances (accessories). The A-weighted sound ratings shown have been calculated per AMCA International Standard 301. Values shown are for inlet LwiA sound power levels for installation Type D: ducted inlet, ducted outlet. Ratings include the effects of duct end correction. The test data were obtained in a laboratory accredited by AMCA for AMCA Standard 210 and 300 testing. CHEM 75R is not licensed to bear the AMCA certified rating seal. 6 R04.4 V2014/April Kennlinie Kennlinie Fan curve Fan curve 20 & CHEM 90R 30 50 200 100 300 500 • V [C.F.M.] ρ = 1.2 kg/m3 CHEM 90R 2000 8 = P (Basic Model) 7 = G1 (Enhanced Model) 1 0.8 kW = G3 (Heavy Model) 6 81 0.6 kW ∆pt[Pa] 5 0.5 kW 78 0.4 kW 1000 900 4 0.32 kW 800 0.25 kW 700 75 3 5800 1/min 0.2 kW 600 72 0.16 kW 500 we r 0.125 kW er I nn 300 69 80 W 4000 1/min 66 60 W 1 40 W 200 20 W 16 W 0.9 3150 1/min 0.8 60 32 W 25 W ∆pt [in.WG] 3550 1/min 63 50 W 0.7 2800 1/min 0.6 57 2500 1/min 54 0.5 2250 1/min 12.5 W 100 90 10 W 80 0.4 2000 1/min 51 8W 70 0.3 1800 1/min Sound Power Level LwiA dB(A) 60 2 4500 1/min 0.1 kW Po 400 5000 1/min 1600 1/min 0.2 50 1400 1/min 40 1250 1/min 30 0.1 0.09 20 30 100 50 0.01 0.02 2 3 2 5 200 0.03 10 3 300 0.1 0.05 20 30 5 Im Kennfeld ist der A-bewertere Schallei- A-weighted sound power level LwiA is stungspegel LwiA angegebenen. quoted in the diagram. Schalldruckpegel LPA in 1,5 m Entfernung Sound pressure level LPA at 1,5 m dist. LPA [dB(A)] = LwiA - 14,5 0.08 • V m3/h 500 50 100 10 • V m3/s 0.2 200 300 1000 pd2 [Pa] 500 20 C2[m/s] 30 Laufraddurchmesser wheel diameter Schaufelzahl number of blades Gewicht weight Drehzahl maximal speed limit 150 12 G = 0,15 nmax = 5800 D= mm z= kg 1/min Fan test test laboratory laboratoryAMCA AMCA210/99 210/99Fig.12, Fig.12,Test TestChamber. Chamber. Performance Performance certified is for is installation for installation type type D - Ducted D - Ducted inlet, inlet, Ducted Ducted outlet.outlet. Performance Power Rating ratings (kW) do not does include not include the effects transmission of appurtenances losses, Performance ratings (accessories-belt cover, do not pulley include & belt). the effects of appurtenances (accessories). The A-weighted sound ratings shown have been calculated per AMCA International Standard 301. Values shown are for inlet LwiA sound power levels for installation Type D: ducted inlet, ducted outlet. Ratings include the effects of duct end correction. The test data were obtained in a laboratory accredited by AMCA for AMCA Standard 210 and 300 testing. CHEM 90R is not licensed to bear the AMCA certified rating seal. R04.4 V2014/April 7 Kennlinie Kennlinie Fan curve Fan curve 20 & CHEM 90FC 30 50 200 100 300 • V [C.F.M.] 500 ρ = 1.2 kg/m3 CHEM 90FC = P (Basic Model) 9 = G1 (Enhanced Model) 8 = G3 (Heavy Model) 89 0.8 kW 0.6 kW 86 0.5 kW 0.4 kW 1000 % ∆pt[Pa] 7 1 kW 6 3 2000 10 5800 1/min 5 83 0.32 kW 5000 1/min 4 900 0.25 kW 800 80 4500 1/min 0.2 kW we r 700 0.16 kW 4000 1/min 77 er Po 600 3 0.125 kW I nn 500 0.1 kW 400 2 3550 1/min 74 80 W ∆pt [in.WG] 3150 1/min 71 60 W 300 2800 1/min 50 W 68 40 W 0.9 32 W 200 1 2500 1/min 65 0.8 2250 1/min 25 W 0.7 2000 1/min 62 20 W 16 W 1800 1/min 10 W 90 80 0.4 1600 1/min 56 Sound Power Level LwiA dB(A) 70 0.5 59 12.5 W 100 0.6 1400 1/min 0.3 1250 1/min 60 0.2 50 40 30 100 50 0.01 0.02 2 3 2 5 200 0.03 10 3 30 50 100 0.2 200 10 Im Kennfeld ist der A-bewertere Schallei- A-weighted sound power level LwiA is stungspegel LwiA angegebenen. quoted in the diagram. Schalldruckpegel LPA in 1,5 m Entfernung Sound pressure level LPA at 1,5 m dist. LPA [dB(A)] = LwiA - 14,5 300 • V m3/h 1000 500 0.1 0.05 20 5 300 500 20 0.3 pd2 [Pa] 1000 30 50 Laufraddurchmesser wheel diameter D= Schaufelzahl number of blades z= Gewicht weight Drehzahl maximal speed limit G= nmax = • V m3/s 150 35 0,19 5800 C2[m/s] mm kg 1/min Fan test test laboratory laboratoryAMCA AMCA210/99 210/99Fig.12, Fig.12,Test TestChamber. Chamber. Performance Performance certified is for is installation for installation type type D - Ducted D - Ducted inlet, inlet, Ducted Ducted outlet.outlet. Performance Power Rating ratings (kW) do not does include not include the effects transmission of appurtenances losses, Performance ratings (accessories-belt cover, do not pulley include & belt). the effects of appurtenances (accessories). The A-weighted sound ratings shown have been calculated per AMCA International Standard 301. Values shown are for inlet LwiA sound power levels for installation Type D: ducted inlet, ducted outlet. Ratings include the effects of duct end correction. The test data were obtained in a laboratory accredited by AMCA for AMCA Standard 210 and 300 testing. CHEM 90FC is not licensed to bear the AMCA certified rating seal. 8 R04.4 V2014/April Kennlinie Kennlinie Fan curve Fan curve & CHEM 110FC 20 10 30 50 200 100 300 • 500 V [C.F.M.] ρ = 1.2 kg/m3 CHEM 110 2000 10 = P (Basic Model) 9 = G1 (Enhanced Model) 8 = G3 (Heavy Model) 0.8 kW 91 0.6 kW 7 1 kW 6 0.5 kW ∆ pt[Pa] 0.4 kW 5 88 0.32 kW 1000 800 4 85 0.25 kW 900 0.2 kW 700 Po we r 600 I nn 0.125 kW 80 W 400 5800 1/min 79 5000 1/min2 0.1 kW er 500 3 82 0.16 kW 76 4500 1/min 60 W 300 4000 1/min 73 50 W 40 W 200 3550 1/min 70 32 W 0.8 3150 1/min 67 20 W 0.7 2800 1/min 16 W 64 0.6 2500 1/min 12.5 W 10 W 1 0.9 25 W 100 ∆pt [in.WG] 58 61 0.5 2250 1/min 0.4 8W 90 2000 1/min 80 Sound Power Level LwiA dB(A) 70 0.3 1800 1/min 60 1600 1/min 50 40 0.2 1400 1/min 1250 1/min 30 0.1 0.09 0.08 • V m3/h 20 10 20 0.003 30 0.01 0.005 0.1 0.2 0.5 100 50 0.3 0.5 1 1 0.02 2 3 2 200 0.03 5 300 0.1 0.05 10 3 Im Kennfeld ist der A-bewertere Schallei- A-weighted sound power level LwiA is stungspegel LwiA angegebenen. quoted in the diagram. Schalldruckpegel LPA in 1,5 m Entfernung Sound pressure level LPA at 1,5 m dist. LPA [dB(A)] = LwiA - 14,5 20 1000 500 30 50 100 0.2 200 300 10 5 20 • V m3/s 0.3 500 1000 C2[m/s] 30 Laufraddurchmesser wheel diameter D= Schaufelzahl number of blades z= Gewicht weight Drehzahl maximal speed limit G= nmax = pd2 [Pa] 150 35 0,19 5800 mm kg 1/min Fan test test laboratory laboratoryAMCA AMCA210/99 210/99Fig.12, Fig.12,Test TestChamber. Chamber. Performance Performance certified is for is installation for installation type type D - Ducted D - Ducted inlet, inlet, Ducted Ducted outlet.outlet. Performance Power Rating ratings (kW) do not does include not include the effects transmission of appurtenances losses, Performance ratings (accessories-belt cover, do not pulley include & belt). the effects of appurtenances (accessories). The A-weighted sound ratings shown have been calculated per AMCA International Standard 301. Values shown are for inlet LwiA sound power levels for installation Type D: ducted inlet, ducted outlet. Ratings include the effects of duct end correction. The test data were obtained in a laboratory accredited by AMCA for AMCA Standard 210 and 300 testing. CHEM 110FC is not licensed to bear the AMCA certified rating seal. R04.4 V2014/April 9 Kennlinie Kennlinie Fan curve Fan curve 30 & CHEM 125 50 200 100 300 • 500 1000 V [C.F.M.] ρ = 1.2 kg/m3 CHEM 125 3000 = P (Basic Model) 10 = G1 (Enhanced Model) 0.8 kW 9 95 = G3 (Heavy Model) 2000 0.6 kW 0.5 kW 7 92 25 0.4 kW kW 0.32 kW 6 1. ∆pt[Pa] 8 1 kW 89 5 0.25 kW 1000 900 800 0.16 kW 700 0.125 kW er er Po w 600 I nn 500 0.1 kW 3 5730 1/min 83 98 80 4500 1/min 77 50 W 40 W 300 4000 1/min 74 1 71 25 W 0.9 3150 1/min 0.8 20 W 68 16 W 12.5 W ∆pt [in.WG] 3550 1/min 32 W 200 5000 1/min 2 80 W 60 W 400 4 86 0.2 kW 0.7 2800 1/min 0.6 2500 1/min 65 10 W 0.5 62 2250 1/min 100 0.4 90 2000 1/min 80 Sound Power Level LwiA dB(A) 70 0.3 1800 1/min 60 1600 1/min 50 0.2 1400 1/min 40 1250 1/min 30 0.1 0.09 20 100 50 0.02 1 200 0.03 2 3 2 300 0.1 0.05 5 10 3 20 30 5 Im Kennfeld ist der A-bewertere Schallei- A-weighted sound power level LwiA is stungspegel LwiA angegebenen. quoted in the diagram. Schalldruckpegel LPA in 1,5 m Entfernung Sound pressure level LPA at 1,5 m dist. LPA [dB(A)] = LwiA - 14,5 0.2 50 0.08 • V m3/h 1000 500 100 10 • V m3/s 0.3 200 300 20 pd2 [Pa] 500 C2[m/s] 30 Laufraddurchmesser wheel diameter D= Schaufelzahl number of blades z= Gewicht weight Drehzahl maximal speed limit G= nmax = 200 16 0,85 5730 mm kg 1/min Fan test test laboratory laboratoryAMCA AMCA210/99 210/99Fig.12, Fig.12,Test TestChamber. Chamber. Performance Performance certified is for is installation for installation type type D - Ducted D - Ducted inlet, inlet, Ducted Ducted outlet.outlet. Performance Power Rating ratings (kW) do not does include not include the effects transmission of appurtenances losses, Performance ratings (accessories-belt cover, do not pulley include & belt). the effects of appurtenances (accessories). The A-weighted sound ratings shown have been calculated per AMCA International Standard 301. Values shown are for inlet LwiA sound power levels for installation Type D: ducted inlet, ducted outlet. Ratings include the effects of duct end correction. The test data were obtained in a laboratory accredited by AMCA for AMCA Standard 210 and 300 testing. CHEM 125 is not licensed to bear the AMCA certified rating seal. 10 R04.4 V2014/April Kennlinie Kennlinie Fan curve Fan curve 50 & CHEM 160 200 100 300 500 • V [C.F.M.] 1000 ρ = 1.2 kg/m3 CHEM 160 = P (Basic Model) 3000 = G1 (Enhanced Model) = G3 (Heavy Model) 1.25 kW 1 kW 0.6 kW 9 W 8 96 kW 0.5 kW 0.4 kW 7 2.5 ∆pt[Pa] 2k 99 0.8 kW 2000 10 1.6 kW 6 93 5 0.32 kW 1000 r 0.25 kW Po we 900 I nn 700 600 90 4000 1/min 0.2 kW er 800 4580 1/min 4 3 87 0.16 kW 3550 1/min 0.125 kW 84 0.1 kW 500 80 W 400 3150 1/min 81 2 ∆pt [in.WG] 2800 1/min 60 W 50 W 300 2500 1/min 78 40 W 2250 1/min 0.9 2000 1/min 25 W 200 72 20 W 1 75 32 W 0.8 0.7 1800 1/min 16 W 0.6 66 69 12.5 W 1600 1/min Sound Power Level LwiA dB(A) 100 0.5 1400 1/min 0.4 90 1250 1/min 80 70 0.3 1120 1/min 60 1000 1/min 50 0.2 40 100 200 0.03 1 300 0.1 0.05 2 3 2 1000 500 5 10 3 0.2 20 30 5 Im Kennfeld ist der A-bewertere Schallei- A-weighted sound power level LwiA is stungspegel LwiA angegebenen. quoted in the diagram. Schalldruckpegel LPA in 1,5 m Entfernung Sound pressure level LPA at 1,5 m dist. LPA [dB(A)] = LwiA - 14,5 50 2000 0.3 100 10 3000 • V m3/s 0.5 200 300 • V m3/h 500 20 1000 pd2 [Pa] C2[m/s] 30 Laufraddurchmesser wheel diameter D= Schaufelzahl number of blades z= Gewicht weight Drehzahl maximal speed limit G= nmax = 250 16 0,95 4580 mm kg 1/min Fan test test laboratory laboratoryAMCA AMCA210/99 210/99Fig.12, Fig.12,Test TestChamber. Chamber. Performance Performance certified is for is installation for installation type type D - Ducted D - Ducted inlet, inlet, Ducted Ducted outlet.outlet. Performance Power Rating ratings (kW) do not does include not include the effects transmission of appurtenances losses, Performance ratings (accessories-belt cover, do not pulley include & belt). the effects of appurtenances (accessories). The A-weighted sound ratings shown have been calculated per AMCA International Standard 301. Values shown are for inlet LwiA sound power levels for installation Type D: ducted inlet, ducted outlet. Ratings include the effects of duct end correction. The test data were obtained in a laboratory accredited by AMCA for AMCA Standard 210 and 300 testing. CHEM 160 is not licensed to bear the AMCA certified rating seal. R04.4 V2014/April 11 Kennlinie Kennlinie Fan curve Fan curve & CHEM 180 200 100 300 500 • 2000 1000 V [C.F.M.] ρ = 1.2 kg/m3 CHEM 180 3000 = P (Basic Model) = G1 (Enhanced Model) = G3 (Heavy Model) 1.25 kW 1 kW 99 0.8 kW 2000 10 2 kW 2.5 9 8 kW 7 96 0.6 kW ∆pt[Pa] 1.6 kW 6 0.5 kW 0.4 kW 93 5 3.2 1000 r Po 800 we 0.25 kW 900 I nn 600 90 0.125 kW 87 99 3550 1/min 102 84 80 W 400 2 2800 1/min 81 60 W 300 ∆pt [in.WG] 2500 1/min 78 50 W 2250 1/min 40 W 1 75 32 W 0.9 2000 1/min 25 W 200 16 W 0.8 72 20 W 1800 1/min 69 0.7 0.6 1600 1/min 66 12.5 W 0.5 Sound Power Level LwiA dB(A) 100 3 3150 1/min 0.1 kW 500 4 4090 1/min 0.2 kW 0.16 kW er 700 kW 0.32 kW 1400 1/min 90 0.4 1250 1/min 80 0.3 70 1120 1/min 60 1000 1/min 0.2 50 900 1/min 40 30 100 200 0.03 2 3 2 1000 500 0.1 0.05 1 1 300 5 0.2 10 3 20 30 5 Im Kennfeld ist der A-bewertere Schallei- A-weighted sound power level LwiA is stungspegel LwiA angegebenen. quoted in the diagram. Schalldruckpegel LPA in 1,5 m Entfernung Sound pressure level LPA at 1,5 m dist. LPA [dB(A)] = LwiA - 14,5 2000 0.3 50 100 10 0.5 200 300 • V m3/h 3000 500 20 • 1 V m3/s 1000 pd2 [Pa] C2[m/s] 30 Laufraddurchmesser wheel diameter D= Schaufelzahl number of blades z= Gewicht weight Drehzahl maximal speed limit G= nmax = 280 mm 20 1,0 kg 4090 1/min Fan test test laboratory laboratoryAMCA AMCA210/99 210/99Fig.12, Fig.12,Test TestChamber. Chamber. Performance Performance certified is for is installation for installation type type D - Ducted D - Ducted inlet, inlet, Ducted Ducted outlet.outlet. Performance Power Rating ratings (kW) do not does include not include the effects transmission of appurtenances losses, Performance ratings (accessories-belt cover, do not pulley include & belt). the effects of appurtenances (accessories). The A-weighted sound ratings shown have been calculated per AMCA International Standard 301. Values shown are for inlet LwiA sound power levels for installation Type D: ducted inlet, ducted outlet. Ratings include the effects of duct end correction. The test data were obtained in a laboratory accredited by AMCA for AMCA Standard 210 and 300 testing. CHEM 180 is not licensed to bear the AMCA certified rating seal. 12 R04.4 V2014/April Kennlinie Fan curve 200 6000 & CHEM 200 300 500 2000 1000 · V [C.F.M.] 3000 ρ = 1,2 kg/m3 CHEM 200 = P (Basic Model) 5000 20 = G1 (Enhanced Model) = G3 (Heavy Model) 4000 5 kW122 4 kW ∆pt[Pa] W 116 2.5 kW 10 113 2 kW 2000 8k 119 3.2 kW 3000 6 kW 9 110 1.6 kW 4800 1/min 8 4500 1/min7 107 1.25 kW 6 104 4000 1/min In n er Po we r 1 kW 1000 800 0.32 kW 600 0.25 kW 500 0.2 kW 0.125 kW 4 ∆pt [in.WG] 3150 1/min 92 3 2800 1/min 89 86 2500 1/min 2 83 2250 1/min 0.16 kW 400 3550 1/min 95 0.4 kW 700 5 101 98 0.6 kW 0.5 kW 900 300 0.8 kW 80 2000 1/min 77 0.1 kW 74 80 W 1800 1/min 71 1 0.9 1600 1/min Sound Power Level LwiA dB(A) 200 0.8 0.7 1400 1/min 0.6 1250 1/min 0.5 1120 1/min 0.4 100 90 80 300 1000 500 0.1 5 0.2 10 3 20 5 2000 0.3 30 50 Fan test laboratory AMCA 210/99 Fig.12, Test Chamber. Performance certified is for installation type D - Ducted inlet, Ducted outlet. Power Rating (kW) does not include transmission losses, Performance ratings do not include the effects of appurtenances (accessories). . V m3/s 1 200 10 LPA [dB(A)] = LwiA - 14,5 . V m3/h 5000 0.5 100 Im Kennfeld ist der A-bewertere Schallei- A-weighted sound power level LwiA is stungspegel LwiA angegebenen. quoted in the diagram. Schalldruckpegel LPA in 1,5 m Entfernung Sound pressure level LPA at 1,5 m dist. 3000 300 20 500 pd2 [Pa] 1000 30 50 Laufraddurchmesser wheel diameter D= Schaufelzahl number of blades z= Gewicht weight Drehzahl maximal speed limit G= nmax = 317 20 1,2 4800 C2[m/s] mm kg 1/min The A-weighted sound ratings shown have been calculated per AMCA International Standard 301. Values shown are for inlet LwiA sound power levels for installation Type D: ducted inlet, ducted outlet. Ratings include the effects of duct end correction. The test data were obtained in a laboratory accredited by AMCA for AMCA Standard 210 and 300 testing. R04.4 V2014/April 13 Kennlinie Fan curve 300 & CHEM 250 500 2000 1000 3000 · V [C.F.M.] 5000 ρ = 1,2 kg/m3 CHEM 250 8000 30 = P (Basic Model) 7000 = G1 (Enhanced Model) = G3 (Heavy Model) 6000 12.5 kW 5000 10 kW ∆pt[Pa] 128 16 kW 20 kW 125 20 8 kW 4000 122 25 119 5 kW 3000 116 4 kW r we Po er In n 1.6 kW 0.5 kW 600 0.4 kW 500 3150 1/min 5 ∆pt [in.WG] 2800 1/min 4 2500 1/min 3 2250 1/min 89 2000 1/min 86 2 0.32 kW 83 0.25 kW 400 0.2 kW 300 6 104 92 0.6 kW 700 7 3550 1/min 107 95 0.8 kW 800 8 98 1 kW 900 4000 1/min 9 101 1.25 kW 1000 10 110 2.5 kW 2 kW 4500 1/min 113 3.2 kW 2000 kW 6 kW 1800 1/min 80 1600 1/min 77 0.16 kW 1400 1/min Sound Power Level LwiA dB(A) 1 0.9 1250 1/min 200 0.8 0.7 1120 1/min 0.6 1000 1/min 0.5 100 1000 500 0.2 5 0.3 10 3 2000 20 3000 1 0.5 30 5 50 5000 100 200 10 Im Kennfeld ist der A-bewertere Schallei- A-weighted sound power level LwiA is stungspegel LwiA angegebenen. quoted in the diagram. Schalldruckpegel LPA in 1,5 m Entfernung Sound pressure level LPA at 1,5 m dist. LPA [dB(A)] = LwiA - 14,5 Fan test laboratory AMCA 210/99 Fig.12, Test Chamber. Performance certified is for installation type D - Ducted inlet, Ducted outlet. Power Rating (kW) does not include transmission losses, Performance ratings do not include the effects of appurtenances (accessories). 10000 0.4 . V m3/h 3 . V m3/s 2000 pd2 [Pa] 2 300 20 500 1000 30 C2[m/s] 50 Laufraddurchmesser wheel diameter D= Schaufelzahl number of blades z= Gewicht weight Drehzahl maximal speed limit G= nmax = 400 20 1,8 4500 mm kg 1/min The A-weighted sound ratings shown have been calculated per AMCA International Standard 301. Values shown are for inlet LwiA sound power levels for installation Type D: ducted inlet, ducted outlet. Ratings include the effects of duct end correction. The test data were obtained in a laboratory accredited by AMCA for AMCA Standard 210 and 300 testing. 14 R04.4 V2014/April Kennlinie Fan curve & CHEM 315 500 2000 1000 3000 5000 10000 ρ = 1,2 kg/m3 CHEM 315 8000 30 = P (Basic Model) 7000 = G1 (Enhanced Model) = G3 (Heavy Model) 6000 20 kW 5000 16 kW ∆pt[Pa] 25 kW 128 32 kW 20 125 12.5 kW 4000 5 kW r we Po er I nn 1.6 kW 1.25 kW 900 800 1 kW 700 0.8 kW 600 0.6 kW 500 0.5 kW 0.4 kW 400 0.32 kW 3150 1/min 110 107 9 8 7 2800 1/min 104 2.5 kW 6 2500 1/min 101 2 kW 1000 10 113 4 kW 3.2 kW 3650 1/min 116 6 kW 2000 kW 119 8 kW 3000 40 122 10 kW 300 · V [C.F.M.] 5 ∆pt [in.WG] 2250 1/min 98 4 2000 1/min 95 92 3 1800 1/min 89 86 1600 1/min 2 83 1400 1/min 80 77 1250 1/min 0.25 kW 1120 1/min Sound Power Level LwiA dB(A) 1 0.9 1000 1/min 200 0.8 0.7 900 1/min 0.6 800 1/min 0.5 100 1000 0.2 2000 0.3 5 20 30 5 50 100 2 200 10 Im Kennfeld ist der A-bewertere Schallei- A-weighted sound power level LwiA is stungspegel LwiA angegebenen. quoted in the diagram. Schalldruckpegel LPA in 1,5 m Entfernung Sound pressure level LPA at 1,5 m dist. LPA [dB(A)] = LwiA - 14,5 Fan test laboratory AMCA 210/99 Fig.12, Test Chamber. Performance certified is for installation type D - Ducted inlet, Ducted outlet. Power Rating (kW) does not include transmission losses, Performance ratings do not include the effects of appurtenances (accessories). 0.4 . V m3/h 10000 5000 1 0.5 10 3 3000 300 20 3 500 5 1000 30 2000 . V m3/s pd2 [Pa] C2[m/s] 50 Laufraddurchmesser wheel diameter D= Schaufelzahl number of blades z= Gewicht weight Drehzahl maximal speed limit G= nmax = 500 20 2,7 3650 mm kg 1/min The A-weighted sound ratings shown have been calculated per AMCA International Standard 301. Values shown are for inlet LwiA sound power levels for installation Type D: ducted inlet, ducted outlet. Ratings include the effects of duct end correction. The test data were obtained in a laboratory accredited by AMCA for AMCA Standard 210 and 300 testing. R04.4 V2014/April 15 Kennlinie Fan curve & CHEM 400 2000 1000 3000 5000 · V [C.F.M.] 10000 ρ = 1,2 kg/m3 CHEM 400 9000 = P (Basic Model) 8000 30 = G1 (Enhanced Model) 7000 = G3 (Heavy Model) 20 kW 6000 ∆pt[Pa] 25 kW 116 16 kW 5000 50 20 kW 110 10 kW 107 8 kW 3000 4 0 kW 113 12.5 kW 4000 32 kW 119 104 6 kW 3300 1/min 101 5 kW 3150 1/min 10 we r 9 Po 4 kW I nn er 2000 3.2 kW 98 2800 1/min 7 95 2500 1/min 2.5 kW 2250 1/min 1.6 kW 1000 1.25 kW 900 1 kW 800 700 0.4 kW 400 1800 1/min 3 1600 1/min 2 1400 1/min 74 0.32 kW 1250 1/min Sound Power Level LwiA dB(A) 300 4 77 0.5 kW 500 2000 1/min 86 80 0.6 kW 600 5 ∆pt [in.WG] 89 83 0.8 kW 6 92 2 kW 8 1120 1/min 1000 1/min 1 0.9 900 1/min 200 0.8 0.7 800 1/min 0.6 0.5 2000 3000 1 0.5 5 10 3 10000 5000 20 30 5 2 50 100 3 200 10 Im Kennfeld ist der A-bewertere Schallei- A-weighted sound power level LwiA is stungspegel LwiA angegebenen. quoted in the diagram. Schalldruckpegel LPA in 1,5 m Entfernung Sound pressure level LPA at 1,5 m dist. LPA [dB(A)] = LwiA - 14,5 Fan test laboratory AMCA 210/99 Fig.12, Test Chamber. Performance certified is for installation type D - Ducted inlet, Ducted outlet. Power Rating (kW) does not include transmission losses, Performance ratings do not include the effects of appurtenances (accessories). 300 20 . V m3/h 20000 . V m3/s 5 500 1000 2000 30 50 Laufraddurchmesser wheel diameter D= Schaufelzahl number of blades z= Gewicht weight Drehzahl maximal speed limit G= nmax = pd2 [Pa] C2[m/s] 560 mm 20 kg 11 3300 1/min The A-weighted sound ratings shown have been calculated per AMCA International Standard 301. Values shown are for inlet LwiA sound power levels for installation Type D: ducted inlet, ducted outlet. Ratings include the effects of duct end correction. The test data were obtained in a laboratory accredited by AMCA for AMCA Standard 210 and 300 testing. 16 R04.4 V2014/April Kennlinie Fan curve & CHEM 450 2000 1000 3000 5000 · V [C.F.M.] 20000 10000 ρ = 1,2 kg/m3 CHEM 450 9000 = P (Basic Model) 8000 30 = G1 (Enhanced Model) 7000 = G3 (Heavy Model) 32 kW 6000 25 kW ∆pt[Pa] 20 kW 5000 16 kW 20 113 110 107 119 10 kW 3000 104 8 kW r we Inn er Po 2000 1 kW 600 5 4 1600 1/min 3 1400 1/min 80 1250 1/min 77 0.6 kW 1120 1/min 71 0.4 kW 300 2 74 0.5 kW ∆pt [in.WG] 1800 1/min 0.8 kW 500 6 2000 1/min 92 83 1.25 kW 700 7 95 86 1.6 kW 9 8 89 2 kW 800 2500 1/min 2250 1/min 4 kW 2.5 kW 900 10 98 5 kW 3.2 kW 1000 2800 1/min 101 6 kW 400 60 kW kW 12.5 kW 50 kW 80 4000 40 kW 116 1000 1/min Sound Power Level LwiA dB(A) 900 1/min 1 0.9 800 1/min 200 0.8 710 1/min 0.7 0.6 630 1/min 0.5 100 2000 3000 10000 5000 1 0.5 5 10 3 20 5 2 30 50 20000 3 100 5 200 10 Im Kennfeld ist der A-bewertere Schallei- A-weighted sound power level LwiA is stungspegel LwiA angegebenen. quoted in the diagram. Schalldruckpegel LPA in 1,5 m Entfernung Sound pressure level LPA at 1,5 m dist. LPA [dB(A)] = LwiA - 14,5 Fan test laboratory AMCA 210/99 Fig.12, Test Chamber. Performance certified is for installation type D - Ducted inlet, Ducted outlet. Power Rating (kW) does not include transmission losses, Performance ratings do not include the effects of appurtenances (accessories). 0.4 . V m3/h 30000 300 20 500 1000 30 10 . V m3/s 2000 pd2 [Pa] C2[m/s] 50 Laufraddurchmesser wheel diameter D= Schaufelzahl number of blades z= Gewicht weight Drehzahl maximal speed limit G= nmax = 662 20 17,5 2800 mm kg 1/min The A-weighted sound ratings shown have been calculated per AMCA International Standard 301. Values shown are for inlet LwiA sound power levels for installation Type D: ducted inlet, ducted outlet. Ratings include the effects of duct end correction. The test data were obtained in a laboratory accredited by AMCA for AMCA Standard 210 and 300 testing. R04.4 V2014/April 17 Kennlinie Fan curve 2000 10000 & CHEM 500 3000 5000 · V [C.F.M.] 20000 10000 ρ = 1,2 kg/m3 CHEM 500 9000 40 = P (Basic Model) 8000 = G1 (Enhanced Model) 30 = G3 (Heavy Model) 7000 40 kW 6000 ∆pt[Pa] 5000 60 kW 80 kW 113 25 kW 20 kW 4000 50 kW 116 32 kW 20 100 kW 110 16 kW Po we r 8 kW In n er 2000 5 kW 3.2 kW 2500 1/min 10 101 2250 1/min 9 98 6 kW 4 kW 119 104 10 kW 8 2000 1/min 95 800 5 89 1600 1/min 1.25 kW 600 4 80 1120 1/min 77 0.8 kW 0.6 kW 2 1000 1/min 74 0.5 kW 300 3 1250 1/min 1 kW 500 ∆pt [in.WG] 1400 1/min 83 1.6 kW 700 6 86 2 kW 900 7 1800 1/min 92 2.5 kW 1000 400 107 12.5 kW 3000 900 1/min Sound Power Level LwiA dB(A) 800 1/min 1 0.9 710 1/min 0.8 200 630 1/min 0.7 0.6 560 1/min 0.5 0.4 . 50000 V m3/h . V m3/s 100 3000 10000 5000 1 5 2 10 3 20 5 30 20000 3 50 100 LPA [dB(A)] = LwiA - 14,5 Fan test laboratory AMCA 210/99 Fig.12, Test Chamber. Performance certified is for installation type D - Ducted inlet, Ducted outlet. Power Rating (kW) does not include transmission losses, Performance ratings do not include the effects of appurtenances (accessories). 10 5 200 10 Im Kennfeld ist der A-bewertere Schallei- A-weighted sound power level LwiA is stungspegel LwiA angegebenen. quoted in the diagram. Schalldruckpegel LPA in 1,5 m Entfernung Sound pressure level LPA at 1,5 m dist. 30000 300 20 500 1000 2000 30 50 Laufraddurchmesser wheel diameter D= Schaufelzahl number of blades z= Gewicht weight Drehzahl maximal speed limit G= nmax = pd2 [Pa] C2[m/s] 748 20 22 2500 mm kg 1/min The A-weighted sound ratings shown have been calculated per AMCA International Standard 301. Values shown are for inlet LwiA sound power levels for installation Type D: ducted inlet, ducted outlet. Ratings include the effects of duct end correction. The test data were obtained in a laboratory accredited by AMCA for AMCA Standard 210 and 300 testing. 18 R04.4 V2014/April Kennlinie Fan curve 2000 & CHEM 560 3000 5000 20000 10000 · V [C.F.M.] 30000 ρ = 1,2 kg/m3 CHEM 560 9000 = P (Basic Model) 8000 30 = G1 (Enhanced Model) 7000 = G3 (Heavy Model) 50 kW 40 kW 116 6000 ∆pt[Pa] 5000 32 kW 25 kW 4000 r 20 2 125 kW12 119 104 12.5 kW Po we 100 kW 113 107 16 kW 101 10 kW 8 98 8 kW In n 1800 1/min 6 kW 95 5 kW 3.2 kW 800 700 1.6 kW 600 400 4 0.8 kW 0.6 kW 300 3 1120 1/min 80 1000 1/min 77 1 kW ∆pt [in.WG] 1250 1/min 1.25 kW 500 6 1400 1/min 89 83 2 kW 7 5 86 2.5 kW 900 1600 1/min 92 4 kW 1000 2200 1/min 10 2000 1/min 9 er 2000 80 kW 110 20 kW 3000 60 kW 2 900 1/min 74 71 800 1/min Sound Power Level LwiA dB(A) 710 1/min 1 0.9 630 1/min 0.8 200 0.7 560 1/min 0.6 500 1/min 0.5 100 3000 10000 5000 1 5 2 10 3 20 5 30 20000 3 50 30000 200 10 Im Kennfeld ist der A-bewertere Schallei- A-weighted sound power level LwiA is stungspegel LwiA angegebenen. quoted in the diagram. Schalldruckpegel LPA in 1,5 m Entfernung Sound pressure level LPA at 1,5 m dist. LPA [dB(A)] = LwiA - 14,5 Fan test laboratory AMCA 210/99 Fig.12, Test Chamber. Performance certified is for installation type D - Ducted inlet, Ducted outlet. Power Rating (kW) does not include transmission losses, Performance ratings do not include the effects of appurtenances (accessories). 300 20 500 0.4 . V m3/h . V m3/s 10 5 100 50000 pd2 [Pa] 1000 30 50 C2[m/s] 841 mm 20 26,5 kg 2200 1/min Laufraddurchmesser wheel diameter D= Schaufelzahl number of blades z= Gewicht weight Drehzahl maximal speed limit G= nmax = The A-weighted sound ratings shown have been calculated per AMCA International Standard 301. Values shown are for inlet LwiA sound power levels for installation Type D: ducted inlet, ducted outlet. Ratings include the effects of duct end correction. The test data were obtained in a laboratory accredited by AMCA for AMCA Standard 210 and 300 testing. R04.4 V2014/April 19 Kennlinie Fan curve 2000 10000 & CHEM 630 3000 5000 20000 10000 · 30000 V [C.F.M.] ρ = 1,2 kg/m3 CHEM 630 9000 40 = P (Basic Model) 8000 = G1 (Enhanced Model) 30 = G3 (Heavy Model) 7000 60 kW 6000 80 kW ∆pt[Pa] 5000 40 kW 32 kW 4000 25 kW r Po we er In n 113 16 122 10 1800 1/min 9 98 10 kW 8 1600 1/min 8 kW 800 2.5 kW 700 5 1250 1/min 4 86 83 500 1 kW 900 1/min 77 1.25 kW 400 2 800 1/min 74 0.8 kW 710 1/min Sound Power Level LwiA dB(A) 300 3 1000 1/min 80 1.6 kW ∆pt [in.WG] 1120 1/min 2 kW 600 6 1400 1/min 89 3.2 kW 900 7 95 92 4 kW 2000 1/min 119 6 kW 1000 kW 101 12.5 kW 5 kW 20 0 110 104 16 kW 2000 125 kW 107 20 kW 3000 100 kW 116 50 kW 630 1/min 1 0.9 560 1/min 0.8 200 500 1/min 0.7 0.6 450 1/min 0.5 0.4 . V m3/h 100 10000 5000 1 2 5 10 3 20000 30000 10 3 20 5 30 50000 50 100 200 10 Im Kennfeld ist der A-bewertere Schallei- A-weighted sound power level LwiA is stungspegel LwiA angegebenen. quoted in the diagram. Schalldruckpegel LPA in 1,5 m Entfernung Sound pressure level LPA at 1,5 m dist. LPA [dB(A)] = LwiA - 14,5 Fan test laboratory AMCA 210/99 Fig.12, Test Chamber. Performance certified is for installation type D - Ducted inlet, Ducted outlet. Power Rating (kW) does not include transmission losses, Performance ratings do not include the effects of appurtenances (accessories). 300 20 500 1000 30 50 Laufraddurchmesser wheel diameter D= Schaufelzahl number of blades z= Gewicht weight Drehzahl maximal speed limit G= nmax = 0 . V m3/s 2000 pd2 [Pa] C2[m/s] 943 mm 20 35 kg 2000 1/min The A-weighted sound ratings shown have been calculated per AMCA International Standard 301. Values shown are for inlet LwiA sound power levels for installation Type D: ducted inlet, ducted outlet. Ratings include the effects of duct end correction. The test data were obtained in a laboratory accredited by AMCA for AMCA Standard 210 and 300 testing. 20 R04.4 V2014/April Kennlinie Fan curve 3000 10000 & CHEM 710 5000 20000 10000 30000 ρ = 1,2 kg/m3 CHEM 710 9000 40 = P (Basic Model) 8000 = G1 (Enhanced Model) 30 = G3 (Heavy Model) 7000 80 kW 6000 100 kW 5000 50 kW 32 kW 160 k W 119 20 113 40 kW 4000 125 kW 116 60 kW ∆pt[Pa] 0k 20 W 122 110 107 25 kW 3000 ow er 16 kW Inn er P 2000 12.5 kW 10 kW 8 kW 1800 1/min 104 20 kW 10 1600 1/min 9 101 8 98 1400 1/min 4 kW 900 800 3.2 kW 700 5 4 1000 1/min 86 83 500 800 1/min 77 1.6 kW 1.25 kW 2 710 1/min 74 1 kW 630 1/min Sound Power Level LwiA dB(A) 300 3 900 1/min 80 2 kW ∆pt [in.WG] 1120 1/min 2.5 kW 600 6 1250 1/min 92 89 5 kW 1000 7 95 6 kW 400 · V [C.F.M.] 50000 560 1/min 1 0.9 500 1/min 200 0.8 450 1/min 0.7 0.6 400 1/min 0.5 100 10000 5000 2 5 3 10 3 20000 20 5 30000 10 5 30 50 0.4 . 100000 V m3/h 50000 100 200 10 Im Kennfeld ist der A-bewertere Schallei- A-weighted sound power level LwiA is stungspegel LwiA angegebenen. quoted in the diagram. Schalldruckpegel LPA in 1,5 m Entfernung Sound pressure level LPA at 1,5 m dist. LPA [dB(A)] = LwiA - 14,5 Fan test laboratory AMCA 210/99 Fig.12, Test Chamber. Performance certified is for installation type D - Ducted inlet, Ducted outlet. Power Rating (kW) does not include transmission losses, Performance ratings do not include the effects of appurtenances (accessories). 300 20 . V m3/s 20 500 1000 2000 30 50 Laufraddurchmesser wheel diameter D= Schaufelzahl number of blades z= Gewicht weight Drehzahl maximal speed limit G= nmax = pd2 [Pa] C2[m/s] 1059 20 45 1800 mm kg 1/min The A-weighted sound ratings shown have been calculated per AMCA International Standard 301. Values shown are for inlet LwiA sound power levels for installation Type D: ducted inlet, ducted outlet. Ratings include the effects of duct end correction. The test data were obtained in a laboratory accredited by AMCA for AMCA Standard 210 and 300 testing. R04.4 V2014/April 21 Kennlinie Fan curve 3000 & CHEM 800 5000 20000 10000 30000 · 50000 V [C.F.M.] ρ = 1,2 kg/m3 CHEM 800 9000 = P (Basic Model) 8000 30 = G1 (Enhanced Model) 7000 = G3 (Heavy Model) 80 kW 6000 60 kW 5000 ∆pt[Pa] 50 kW 4000 Inn er Po w er 2000 12.5 kW 900 119 101 9 1400 1/min 98 2 kW 500 1250 1/min 92 1.25 kW 1 kW 300 6 1120 1/min 5 ∆pt [in.WG] 1000 1/min 4 900 1/min 3 83 800 1/min 710 1/min 77 1.6 kW 8 7 95 80 2.5 kW 600 1600 1/min 10 86 3.2 kW 700 400 122 4 kW 800 20 W 89 6 kW 5 kW 0k 10 kW 8 kW 1000 20 113 104 25 kW 16 kW 160 kW 107 32 kW 20 kW 125 kW 110 40 kW 3000 100 kW 116 74 2 630 1/min 71 560 1/min Sound Power Level LwiA dB(A) 500 1/min 1 0.9 450 1/min 200 0.8 0.7 400 1/min 0.6 355 1/min 0.5 0.4 100 90 10000 5000 2 5 3 20000 3 10 20 5 30000 50000 5 30 10 100 50 200 10 Im Kennfeld ist der A-bewertere Schallei- A-weighted sound power level LwiA is stungspegel LwiA angegebenen. quoted in the diagram. Schalldruckpegel LPA in 1,5 m Entfernung Sound pressure level LPA at 1,5 m dist. LPA [dB(A)] = LwiA - 14,5 Fan test laboratory AMCA 210/99 Fig.12, Test Chamber. Performance certified is for installation type D - Ducted inlet, Ducted outlet. Power Rating (kW) does not include transmission losses, Performance ratings do not include the effects of appurtenances (accessories). 100000 . V m3/h 30 . V m3/s 20 300 20 500 pd2 [Pa] 1000 30 50 Laufraddurchmesser wheel diameter D= Schaufelzahl number of blades z= Gewicht weight Drehzahl maximal speed limit G= nmax = C2[m/s] 1140 mm 20 75 kg 1600 1/min The A-weighted sound ratings shown have been calculated per AMCA International Standard 301. Values shown are for inlet LwiA sound power levels for installation Type D: ducted inlet, ducted outlet. Ratings include the effects of duct end correction. The test data were obtained in a laboratory accredited by AMCA for AMCA Standard 210 and 300 testing. 22 R04.4 V2014/April Kennlinie Fan curve & CHEM 900 5000 20000 10000 30000 · 50000 V [C.F.M.] ρ = 1,2 kg/m3 CHEM 900 8000 30 = P (Basic Model) 7000 = G1 (Enhanced Model) 6000 = G3 (Heavy Model) 6 100 kW 11 125 kW 80 kW 113 5000 ∆pt[Pa] 60 kW 4000 50 kW 32 kW 25 kW 20 kW r 2000 Po we er Inn 6 kW 3.2 kW 600 2.5 kW 500 122 104 10 1400 1/min 101 9 98 1250 1/min 8 7 1120 1/min 6 92 1000 1/min 89 5 900 1/min 4 ∆pt [in.WG] 800 1/min 83 4 kW 700 119 86 5 kW 800 110 95 12.5 kW 8 kW 900 20 kW 16 kW 10 kW 1000 200 107 40 kW 3000 160 kW 3 710 1/min 80 77 630 1/min 2 2 kW 400 74 1.6 kW 1.25 kW 560 1/min 71 500 1/min 300 Sound Power Level LwiA dB(A) 450 1/min 1 0.9 400 1/min 200 0.8 0.7 355 1/min 0.6 315 1/min 0.5 0.4 100 90 10000 2 5 20000 3 20 5 30 50000 10 5 10 3 30000 50 100 LPA [dB(A)] = LwiA - 14,5 Fan test laboratory AMCA 210/99 Fig.12, Test Chamber. Performance certified is for installation type D - Ducted inlet, Ducted outlet. Power Rating (kW) does not include transmission losses, Performance ratings do not include the effects of appurtenances (accessories). . V m3/h 30 . V m3/s 20 200 10 Im Kennfeld ist der A-bewertere Schallei- A-weighted sound power level LwiA is stungspegel LwiA angegebenen. quoted in the diagram. Schalldruckpegel LPA in 1,5 m Entfernung Sound pressure level LPA at 1,5 m dist. 100000 300 20 500 pd2 [Pa] 1000 30 C2[m/s] 50 Laufraddurchmesser wheel diameter D= Schaufelzahl number of blades z= Gewicht weight Drehzahl maximal speed limit G= nmax = 1258 20 85 1400 mm kg 1/min The A-weighted sound ratings shown have been calculated per AMCA International Standard 301. Values shown are for inlet LwiA sound power levels for installation Type D: ducted inlet, ducted outlet. Ratings include the effects of duct end correction. The test data were obtained in a laboratory accredited by AMCA for AMCA Standard 210 and 300 testing. R04.4 V2014/April 23 Kennlinie Fan curve 5000 9000 & CHEM 1000 20000 10000 30000 · 100000 V [C.F.M.] 50000 ρ = 1,2 kg/m3 CHEM 1000 8000 = P (Basic Model) 7000 30 = G1 (Enhanced Model) = G3 (Heavy Model) 6000 116 160 kW 125 kW 100 kW 5000 200 kW 250 113 kW 20 80 kW ∆pt[Pa] 110 40 kW 32 kW Po w Inn er 104 1250 1/min10 101 9 92 900 89 86 710 1/min 3.2 kW 500 3 630 1/min 80 4 kW 600 4 ∆pt [in.WG] 83 5 kW 700 5 800 1/min 6 kW 800 6 900 1/min 8 kW 8 7 1000 1/min 95 16 kW 10 kW 1120 1/min 98 20 kW 12.5 kW 1000 119 122 25 kW er 2000 kW 107 50 kW 3000 0 60 kW 32 4000 77 560 1/min 2 2.5 kW 400 74 2 kW 500 1/min 71 1.6 kW 450 1/min 300 Sound Power Level LwiA dB(A) 400 1/min 1 0.9 355 1/min 200 0.8 0.7 315 1/min 0.6 280 1/min 0.5 100 0.4 90 10000 2 20000 3 5 20 5 30 50 20 100 200 10 Im Kennfeld ist der A-bewertere Schallei- A-weighted sound power level LwiA is stungspegel LwiA angegebenen. quoted in the diagram. Schalldruckpegel LPA in 1,5 m Entfernung Sound pressure level LPA at 1,5 m dist. LPA [dB(A)] = LwiA - 14,5 Fan test laboratory AMCA 210/99 Fig.12, Test Chamber. Performance certified is for installation type D - Ducted inlet, Ducted outlet. Power Rating (kW) does not include transmission losses, Performance ratings do not include the effects of appurtenances (accessories). . V m3/h 100000 50000 10 5 10 3 30000 300 20 30 500 1000 30 50 Laufraddurchmesser wheel diameter D= Schaufelzahl number of blades z= Gewicht weight Drehzahl maximal speed limit G= nmax = 50 . V m3/s 2000 pd2 [Pa] C2[m/s] 1429 mm 20 100 kg 1250 1/min The A-weighted sound ratings shown have been calculated per AMCA International Standard 301. Values shown are for inlet LwiA sound power levels for installation Type D: ducted inlet, ducted outlet. Ratings include the effects of duct end correction. The test data were obtained in a laboratory accredited by AMCA for AMCA Standard 210 and 300 testing. 24 R04.4 V2014/April Kennlinie Fan curve 20000 10000 9000 & CHEM 1120 30000 50000 · V [C.F.M.] 100000 ρ = 1,2 kg/m3 CHEM 1120 8000 = P (Basic Model) 7000 30 = G1 (Enhanced Model) = G3 (Heavy Model) 6000 160 kW 125 kW 5000 20 0k 119 W 107 60 kW 50 kW 40 kW kW 110 80 kW 3000 320 40 4000 250 kW 113 100 kW ∆pt[Pa] 116 200 kW 122 104 1120 1/min 10 101 9 32 kW Inn er Po w er 2000 6 92 800 1/min 89 700 630 1/min 5 kW 4 kW 500 3 83 6 kW 600 4 ∆pt [in.WG] 86 8 kW 800 5 710 1/min 10 kW 900 8 7 900 1/min 95 20 kW 12.5 kW 1000 98 25 kW 16 kW 1000 1/min 560 1/min 80 77 500 1/min 2 3.2 kW 400 74 2.5 kW 450 1/min 71 2 kW 400 1/min 300 Sound Power Level LwiA dB(A) 355 1/min 1 0.9 315 1/min 200 0.8 0.7 280 1/min 0.6 250 1/min 0.5 0.4 100 90 10000 20000 3 30000 10 5 5 10 3 100000 50000 20 5 30 50 20 100 200 10 Im Kennfeld ist der A-bewertere Schallei- A-weighted sound power level LwiA is stungspegel LwiA angegebenen. quoted in the diagram. Schalldruckpegel LPA in 1,5 m Entfernung Sound pressure level LPA at 1,5 m dist. LPA [dB(A)] = LwiA - 14,5 Fan test laboratory AMCA 210/99 Fig.12, Test Chamber. Performance certified is for installation type D - Ducted inlet, Ducted outlet. Power Rating (kW) does not include transmission losses, Performance ratings do not include the effects of appurtenances (accessories). 200000 30 300 20 500 . V m3/s 50 2000 pd2 [Pa] 1000 30 . V m3/h C2[m/s] 50 Laufraddurchmesser wheel diameter D= Schaufelzahl number of blades z= Gewicht weight Drehzahl maximal speed limit G= nmax = 1600 20 130 1120 mm kg 1/min The A-weighted sound ratings shown have been calculated per AMCA International Standard 301. Values shown are for inlet LwiA sound power levels for installation Type D: ducted inlet, ducted outlet. Ratings include the effects of duct end correction. The test data were obtained in a laboratory accredited by AMCA for AMCA Standard 210 and 300 testing. R04.4 V2014/April 25 Kennlinie Fan curve 20000 10000 9000 & CHEM 1250 30000 50000 · V [C.F.M.] 100000 ρ = 1,2 kg/m3 CHEM 1250 8000 = P (Basic Model) 7000 30 = G1 (Enhanced Model) = G3 (Heavy Model) 6000 200 kW 160 kW 5000 125 kW ∆pt[Pa] 4000 100 kW 80 kW 3000 Po w Inn er 900 107 119 122 1000 1/min 10 101 600 5 kW 500 8 6 92 710 1/min 5 89 630 1/min 4 ∆pt [in.WG] 86 560 1/min 3 500 1/min 80 6 kW 9 7 800 1/min 95 83 8 kW 700 20 110 10 kW 800 kW 98 25 kW 16 kW 12.5 kW 113 900 1/min 32 kW 20 kW 1000 400 40 kW er 2000 320 kW 104 60 kW 50 kW 116250 kW 450 1/min 77 2 4 kW 400 71 2.5 kW 300 400 1/min 74 3.2 kW 355 1/min Sound Power Level LwiA dB(A) 315 1/min 1 0.9 280 1/min 200 0.8 0.7 250 1/min 0.6 225 1/min 0.5 0.4 100 90 20000 30000 10 5 5 10 3 100000 50000 20 5 30 20 50 100 30 200 10 Im Kennfeld ist der A-bewertere Schallei- A-weighted sound power level LwiA is stungspegel LwiA angegebenen. quoted in the diagram. Schalldruckpegel LPA in 1,5 m Entfernung Sound pressure level LPA at 1,5 m dist. LPA [dB(A)] = LwiA - 14,5 Fan test laboratory AMCA 210/99 Fig.12, Test Chamber. Performance certified is for installation type D - Ducted inlet, Ducted outlet. Power Rating (kW) does not include transmission losses, Performance ratings do not include the effects of appurtenances (accessories). 300 20 . V m3/h 200000 . V m3/s 50 500 1000 30 2000 C2[m/s] 50 Laufraddurchmesser wheel diameter D= Schaufelzahl number of blades z= Gewicht weight Drehzahl maximal speed limit G= nmax = pd2 [Pa] 1800 20 160 1000 mm kg 1/min The A-weighted sound ratings shown have been calculated per AMCA International Standard 301. Values shown are for inlet LwiA sound power levels for installation Type D: ducted inlet, ducted outlet. Ratings include the effects of duct end correction. The test data were obtained in a laboratory accredited by AMCA for AMCA Standard 210 and 300 testing. 26 R04.4 V2014/April & Sound Information Sound power levels This term refers to the power which a source radiates as sound. Sound power levels are expressed in decibels with a reference level of 1 picoWatt. The sound power level of a source remains the same regardless of its environment and the distance to the listener. If the sound power frequency spectrum is needed, for as follows: example, the design of sound attenuators, the A- rated sound power levels at particular octave band frequency LWA can be calculated by subtracting the relative sound Lwrel. LWA = Lwi + Lwrel Sound pressure level Pegelabnahme / noise reduction Noise reduction ∆L [dB] L [dB] These are pressure fluctuations generated by a source expressed in decibels with a reference level of 20 µPa. The sound pressure level varies with the distance of a sound source to the listener and its environment. Sound level reduction half sphere 30 a: without reflexion b: with reflexion c: full sphere without reflexion 25 c 20 a b 15 10 5 0 0,5 0,6 0,8 2 1 3 4 5 6 7 8 9 10 Entfernung / distance Distance [m] [m] Frequencies Sound is split into different frequencies. Frequencies of human hearing range from about 20 cycles per second (Hz) to 20.000 cycles per second (Hz). For practical purposes, WOLTER publishes noise data in eight octave bands with the centre frequencies of (63,) 125, 250, 500, 1000, 2000, 4000 and 8000 Hz. Each fan has its own specific correction factor which is to be deducted from sound power according to the octave band and is shown on the buttom line of each perfomance curve. A-weighted sound pressure level in dB (A) The human ear is more sensitive to sound in some frequencies than in others. The A-weighting is an attempt to reflect this natural perception of sound. The A-weighting is a set of figures which are applied to the sound pressure levels. The levels in each of the octave bands are added logarithmically to give a single figure. The A-weighting over the octave band is as follows: Table 1) Table 2) Addition of sound levels Frequency [Hz] 63 125 250 500 1000 2000 4000 8000 A-weighting [dB] -25,5 -15,5 -8,5 -3 0 +1 +1 -1 Difference between two sound levels Add to the higher level [dB] [dB] 0-1 3 2-3 2 4-9 > =10 1 L∑ = 10 · lg(10 0,1·L1 + 10 0,1·L2 + ... + 10 0,1·Ln ) 0 where: L1= sound level of a source 1 L∑= resulting summation sound level Summation of several congeneric sound levels L∑ = L1 + 10 · lg(z) R04.4 V2014/April where: z = number of sources L1= sound level of a single source L∑= resulting summation sound level 27 & Sound Information Relative Sound Power Frequency Spectrum (Lwrel) [dB] Fan Model Speed 63 125 250 500 1000 2000 4000 8000 Size [RPM] [Hz] [Hz] [Hz] [Hz] [Hz] [Hz] [Hz] [Hz] 1250 ~ 2250 -4 -4 -13 -8 -16 -28 -34 -39 2500 ~ 5800 -8 -4 -5 -14 -9 -18 -30 -36 1250 ~ 2250 -4 -4 -13 -8 -16 -28 -34 -39 2500 ~ 5800 -8 -4 -5 -14 -9 -18 -30 -36 1250 ~ 2250 -4 -4 -13 -8 -16 -28 -34 -39 2500 ~ 5800 -8 -4 -5 -14 -9 -18 -30 -36 1250 ~ 2250 -4 -4 -13 -8 -16 -28 -34 -39 2500 ~ 5730 -8 -4 -5 -14 -9 -18 -30 -36 900 ~ 2000 -3 -6 -14 -7 -23 -30 -36 -40 2250 ~ 4580 -7 -4 -7 -15 -8 -23 -31 -37 900 ~ 1800 -2 -7 -12 -8 -24 -30 -36 -40 2000 ~ 4090 -6 -4 -9 -13 -9 -25 -32 -38 1120 ~2000 -3 -6 -14 -7 -23 -30 -36 -40 2250 ~ 4800 -7 -4 -7 -15 -8 -23 -31 -37 1000 ~ 1800 -3 -6 -14 -7 -23 -30 -36 -40 2000 ~ 4500 -7 -4 -7 -15 -8 -23 -31 -37 900 ~ 1600 -2 -9 -10 -9 -25 -31 -36 -40 1800 ~ 3650 -5 -3 -10 -12 -11 -26 -32 -38 800 ~ 1800 -4 -4 -8 -16 -19 -24 -30 -33 2000 ~ 3300 -5 -4 -7 -7 -17 -20 -25 -30 75 90 110 125 160 180 200 250 315 400 450 500 560 630 710 800 900 1000 1120 1250 630 ~ 1600 -4 -4 -8 -16 -19 -24 -30 -33 1800 ~ 2800 -4 -5 -6 -10 -18 -21 -26 -31 560 ~ 1250 -4 -4 -9 -16 -19 -25 -30 -34 1400 ~ 2500 -4 -6 -6 -14 -19 -23 -29 -33 500 ~ 1120 -4 -3 -11 -16 -20 -26 -30 -34 1250 ~ 2200 -4 -6 -6 -13 -19 -22 -28 -32 450 ~ 1000 -4 -3 -12 -16 -20 -26 -30 -34 1120 ~ 2200 -4 -6 -6 -14 -19 -23 -29 -33 400 ~ 800 -2 -6 -14 -17 -22 -27 -31 -36 900 ~ 1800 -4 -4 -8 -16 -19 -24 -30 -33 355 ~ 710 -1 -7 -14 -17 -23 -28 -31 -37 800 ~ 1600 -4 -4 -9 -16 -19 -25 -30 -34 315 ~ 630 -1 -8 -14 -17 -23 -28 -32 -38 710 ~ 1400 -4 -3 -11 -16 -20 -26 -30 -34 280 ~ 560 -1 -8 -14 -17 -23 -28 -32 -37 630 ~ 1250 -4 -3 -12 -16 -20 -26 -30 -34 250 ~ 500 -1 -10 -14 -18 -24 -28 -32 -40 560 ~ 1120 -3 -4 -13 -16 -21 -27 -31 -35 225 ~ 450 -1 -9 -14 -18 -24 -28 -32 -39 500 ~ 1000 -3 -4 -13 -16 -21 -27 -31 -35 • Sound power frequency spectrum calculated with this Lwrel are not licensed by AMCA. 28 R04.4 V2014/April & Abmessungen Dimension CHEM 75R - 110FC PP Approx. C ØD2 L3 L8 H H1 ØD1 H2 H3 (Mtr = F56) F Drehrichtung von Antriebsseite aus gesehen G = Gewicht des nackten Ventilators ohne Antrieb The direction of rotation is as viewed from the drive side G = Barefan weight approximatly F1 L1 C9 C1 L2 4 x Ø8.5 C2 Baugröße C C1 C2 C9 D1 D2 F F1 size [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] 75R 283 107 131 125 75 75 35 84 90R 347 107 131 183 90 90 37 109 90FC 347 107 131 183 90 90 37 109 110FC 347 107 131 183 110 110 37 109 Baugröße H H1 H2 H3 L1 L2 L3 L8 size [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] 75R 158 170 198 100 181 206 200 88 90R 158 212 292 170 181 206 251 112 90FC 158 212 292 170 181 206 251 112 110FC 158 212 292 170 181 206 251 112 Maß- und Konstruktionsänderungen, dem technischen Fortschritt dienend, bleiben uns vorbehalten. We reserve the right to alter measurements without notice in case of technical improvements RD 0 RD 45 LG 0 LG 45 RD 90 RD 135 RD 180 LG 90 LG 135 LG 180 H = H2a R04.4 V2014/April RD 225 RD 270 LG 225 LG 270 H = H2b RD 315 H = H2a LG 315 29 & Abmessungen Dimension CHEM 125-400 PP Ø D3 Ø D2 4 nos x 8.5 dia. H4 H1 Ø D1 H3 L3 C3 L1 L2 C1 C2 E1 L7 Drehrichtung von Antriebsseite aus gesehen G = Gewicht des nackten Ventilators ohne Antrieb The direction of rotation is as viewed from the drive side G = Barefan weight approximatly H5 H2 6305x2 24 Dia x 8mm key C8 C7 C6 C9 C5 L6 L4 L5 C4 Größe D1D2D3C1C2C3C4C5C6C7C8C9E1H1 size (mm)(mm)(mm)(mm)(mm)(mm)(mm)(mm)(mm)(mm)(mm)(mm)(mm)(mm) 125125125185256294100425320100 19 19 127 95 351 160160160220282320100475320128 19 19 162116445 180180180240312350100550320150 19 19 206132503 200200200260312350100550320150 25 25 203124518 250250250310300350100600450150 25 25 231140621 315315315375350400125650450150 25 25 281165780 400400400480400450150650450150 25 25 321201898 Größe H2a H2bH3H4H5L1L2L3L4L5L6L7 G size (mm)(mm)(mm)(mm)(mm)(mm)(mm)(mm)(mm)(mm)(mm)(mm) (kg) 125228308170 20 50 298336400210260 12 142 18 160291396217 20 50 370408504282332 12 182 32 180327440250 20 50 411449571308373 19 234 38 200364500271 20 50 453491590345415 12 204 43 250454633320 30 80 568618723442518 19 261 52 315530720412 30 80 659709910533609 19 332 78 400557750458 30 80 7217711043595671 19 356108 Maß- und Konstruktionsänderungen, dem technischen Fortschritt dienend, bleiben uns vorbehalten. We reserve the right to alter measurements without notice in case of technical improvements RD 0 RD 45 LG 0 LG 45 RD 90 RD 135 RD 180 LG 90 LG 135 LG 180 H = H2a 30 RD 225 RD 270 LG 225 LG 270 H = H2b RD 315 H = H2a LG 315 R04.4 V2014/April & Abmessungen Dimension CHEM 200-400 GRP Ø D2 4 nos x 8.5 dia. H4 H1 Ø D1 H3 L3 C3 L1 L2 C1 C2 E1 L7 H5 H2 6305x2 24 Dia x 8mm key Drehrichtung von Antriebsseite aus gesehen G = Gewicht des nackten Ventilators ohne Antrieb The direction of rotation is as viewed from the drive side G = Barefan weight approximatly C7 C8 L6 12 L4 C6 L5 C5 C9 C4 Größe D1D2D3C1C2C3C4C5C6C7C8C9E1H1 size (mm)(mm)(mm)(mm)(mm)(mm)(mm)(mm)(mm)(mm)(mm)(mm)(mm)(mm) 200192193 na 312350100550320150 25 25 189110505 250240242 na 300350100600450150 25 25 210121658 315305306 na 350400125650450150 25 25 245142795 400386390 na 400450150650450150 25 25 280165858 Größe H2a H2bH3H4H5L1L2L3L4L5L6L7 G size (mm)(mm)(mm)(mm)(mm)(mm)(mm)(mm)(mm)(mm)(mm)(mm) (kg) 200364500294 38 50 453491590345410 19 227 43 250454633337 50 80 568618722442518 19 269 52 315530720464 50 80 659709930533609 19 358 78 400557750510 50 80 7217711003595671 19 357108 Maß- und Konstruktionsänderungen, dem technischen Fortschritt dienend, bleiben uns vorbehalten. We reserve the right to alter measurements without notice in case of technical improvements RD 0 RD 45 LG 0 LG 45 RD 90 RD 135 RD 180 LG 90 LG 135 LG 180 H = H2a R04.4 V2014/April RD 225 RD 270 LG 225 LG 270 H = H2b RD 315 H = H2a LG 315 31 & Abmessungen Dimension CHEM 450-710 GRP ØA2 ØA1 L5 ØD1 Ød H1 C6 C3 L3 4nos X 13.0dia. C4 C2 C1 H3 L2 L1 H2 H4 L4 Drehrichtung von Antriebsseite aus gesehen G = Gewicht des nackten Ventilators ohne Antrieb The direction of rotation is as viewed from the drive side G = Barefan weight approximatly L7 L6 d [mm] Key [mm] 45 60 14 x 9 18 x 11 Größe A1A2B1B2C1C2C3C4C5C6D1 dH1a H1b size [mm][mm][mm][mm][mm][mm][mm][mm][mm][mm][mm][mm][mm][mm] 450457557 - - 977604 19 75 - 100450 45 685598 500517617 - - 1013604 19 75 - 100500 45 783633 560580680 - - 1058604 19 75 - 125560 45 870709 630651751 - - 1184677 19 75 - 125630 60 939775 710731831 - - 1332761 19 75 - 125710 601030900 Größe H1c H1d H1eH2H3H4L1L2L3L4L5L6L7 G size [mm][mm][mm][mm][mm][mm][mm][mm][mm][mm][mm][mm][mm] (kg) 450TBA800700571418467858430 25 25 4481210494156 500TBA911786634465518970448 25 25 5701360549188 560 TBA1005879 710 521 5801090448 25 25 6301520615 228 630 TBA1128950 799 586 6531222507 25 25 7051720692 248 710 TBA12501110900 660 7361273573 25 25 7951930780 280 Maß- und Konstruktionsänderungen, dem technischen Fortschritt dienend, bleiben uns vorbehalten. We reserve the right to alter measurements without notice in case of technical improvements RD 0 RD 45 LG 0 LG 45 RD 90 RD 135 RD 180 LG 90 LG 135 LG 180 H = H2a 32 RD 225 RD 270 LG 225 LG 270 H = H2b RD 315 H = H2a LG 315 R04.4 V2014/April & Abmessungen Dimension CHEM 800-1250 GRP ØA2 ØA1 L6 ØD1 Ød H1 C6 C3 L4 L2 L1 C4 C2 C1 H3 4nos x13.0dia H2 H4 L5 Drehrichtung von Antriebsseite aus gesehen G = Gewicht des nackten Ventilators ohne Antrieb The direction of rotation is as viewed from the drive side G = Barefan weight approximatly L8 L7 d [mm] Key [mm] 70 80 20 x 12 22 x 14 Größe A1A2B1B2C1C2C3C4C5C6D1 dH1a H1b size [mm][mm][mm][mm][mm][mm][mm][mm][mm][mm][mm][mm][mm][mm] 800790900 - - 1417761 25 75 - 160800 701130 1000 900875995 - - 1756 100025 75 - 160900 701278 1105 10009881130 - - 1833 100025 75 - 1601000701375 1200 112011071256 - - 18961000 25 75 - 200 1120 80 15501350 125012421390 - - 19911000 25 75 - 200 1250 80 17001500 Größe H1c H1d H1eH2H3H4L1L2L4L5L6L7L8 G size [mm][mm][mm][mm][mm][mm][mm][mm][mm][mm][mm][mm][mm] (kg) 800 TBA128012301014744 82914501400721 25 7292029879 420 900 TBA142813621141837 93316321582818 25 8212282989 500 1000 TBA 156015001268 930 103718131763 914 25 912 25361099 625 1120 TBA 17601600142010411161203019801030 25 102128401231 722 1250 TBA 19351800158511621296210020501140 25 114031701373 859 Maß- und Konstruktionsänderungen, dem technischen Fortschritt dienend, bleiben uns vorbehalten. We reserve the right to alter measurements without notice in case of technical improvements RD 0 RD 45 LG 0 LG 45 RD 90 RD 135 RD 180 LG 90 LG 135 LG 180 H = H2a R04.4 V2014/April RD 225 RD 270 LG 225 LG 270 H = H2b RD 315 H = H2a LG 315 33 & Abmessungen Dimension Transition Outlet ØD5 NH2 NH1 ØD4 ØD2 A1 B1 ØD3 A2 B2 Baugröße A1 A2 B1 B2 D2 D3 D4 D5 NH1 NH2 size [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] 125 - - - - 125 185 110 - 100 - 160 - - - - 160 220 125 - 100 - 180 - - - - 180 240 160 - 120 - 200 - - - - 200 260 180 - 120 - 250 - - - - 250 310 200 - 150 - 315 - - - - 315 375 250 - 150 - 400 - - - - 400 480 315 - 200 - 450 440 530 360 450 457 557 400 449 250 252 500 490 590 400 500 517 617 450 500 270 274 560 550 650 450 550 580 680 500 561 300 302 630 620 720 505 605 651 751 560 631 330 333 710 710 810 580 680 731 831 630 724 370 375 800 830 940 590 700 790 900 710 802 410 410 900 945 1065 665 785 875 995 800 888 450 450 1000 1034 1176 748 886 988 1130 900 984 490 492 1120 1176 1325 838 992 1107 1256 1000 1129 550 557 1250 1291 1439 917 1065 1242 1390 1120 1228 600 601 Maß- und Konstruktionsänderungen, dem technischen Fortschritt dienend, bleiben uns vorbehalten. We reserve the right to alter measurements without notice in case of technical improvements RD 0 RD 45 LG 0 LG 45 RD 90 RD 135 RD 180 LG 90 LG 135 LG 180 H = H2a 34 RD 225 RD 270 LG 225 LG 270 H = H2b RD 315 H = H2a LG 315 R04.4 V2014/April & Abmessungen Dimension Fume Jet Nozzles (S Type: SE 30) ØD ØB CH ØD NH JH JH CH ØB ØA A N ØAA AA NN Fan model AA NN A N B D CH NH JH Fan Height Size [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] 125 185 - 121 - 166 185 137 - 240 448 160 220 - 154 - 211 235 175 - 305 559 180 240 - 174 - 238 266 198 - 345 636 200 260 - 194 - 266 296 220 - 384 667 250 310 - 245 - 335 374 278 - 485 854 315 375 - 309 - 423 472 351 - 612 1018 400 480 - 392 - 537 599 445 - 777 1147 450 530 450 440 360 615 686 510 202 1091 1152 500 590 500 490 400 684 763 568 224 1214 1301 560 650 550 550 450 768 858 638 252 1364 1451 630 720 605 620 505 864 965 717 283 1534 1595 710 810 680 710 580 991 1106 823 325 1760 1770 800 940 700 830 590 1091 1225 911 360 1948 1960 900 1065 785 945 665 1216 1357 1009 399 2159 2200 1000 1176 886 1034 748 1348 1504 1118 442 2392 2420 1120 1325 992 1176 838 1546 1725 1283 507 2744 2700 1250 1439 1065 1291 917 1681 1876 1395 551 2984 3000 Maß- und Konstruktionsänderungen, dem technischen Fortschritt dienend, bleiben uns vorbehalten. We reserve the right to alter measurements without notice in case of technical improvements RD 0 RD 45 LG 0 LG 45 RD 90 RD 135 RD 180 LG 90 LG 135 LG 180 H = H2a R04.4 V2014/April RD 225 RD 270 LG 225 LG 270 H = H2b RD 315 H = H2a LG 315 35 & Abmessungen Dimension Fume Jet Nozzles (H Type: HE 40) ØD ØB ØD ØB ØD NH JH CH JH CH CH ØB ØA ØAA A AA N NN Fan model AA NN A N B D CH NH JH Fan Height Size [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] 125 185 - 121 - 99 137 138 - 217 448 160 220 - 154 - 125 174 176 - 276 559 180 240 - 174 - 142 197 198 - 312 636 200 260 - 194 - 158 219 221 - 348 667 250 310 - 245 - 200 277 279 - 440 854 315 375 - 309 - 252 349 352 - 554 1018 400 480 - 392 - 319 443 447 - 703 1147 450 530 450 440 360 366 508 512 260 860 1152 500 590 500 490 400 407 565 569 289 957 1301 560 650 550 550 450 457 635 640 325 1075 1451 630 720 605 620 505 514 714 720 366 1210 1595 710 810 680 710 580 590 819 825 419 1387 1770 800 940 700 830 590 653 906 914 464 1536 1960 900 1065 785 945 665 724 1004 1013 514 1702 2200 1000 1176 886 1034 748 802 1113 1122 570 1886 2420 1120 1325 992 1176 838 920 1276 1287 654 2163 2700 1250 1439 1065 1291 917 1000 1388 1400 711 2352 3000 Maß- und Konstruktionsänderungen, dem technischen Fortschritt dienend, bleiben uns vorbehalten. We reserve the right to alter measurements without notice in case of technical improvements RD 0 RD 45 LG 0 LG 45 RD 90 RD 135 RD 180 LG 90 LG 135 LG 180 H = H2a 36 RD 225 RD 270 LG 225 LG 270 H = H2b RD 315 H = H2a LG 315 R04.4 V2014/April & Abmessungen Dimension Fume Jet Nozzles (H Type: HDE 80) ØD ØB NH JH JH CH CH ØD ØB CH ØD ØB A AA ØA ØAA N NN Fan model AA NN A N B D CH NH JH Fan Height Size [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] 125 185 - 121 - 175 136 142 - 330 448 160 220 - 154 - 223 173 181 - 420 559 180 240 - 174 - 252 196 205 - 474 636 200 260 - 194 - 281 218 228 - 529 667 250 310 - 245 - 355 275 288 - 668 854 315 375 - 309 - 448 347 363 - 842 1018 400 480 - 392 - 568 441 461 - 1068 1147 450 530 450 440 360 651 505 528 260 1278 1152 500 590 500 490 400 724 562 587 289 1422 1301 560 650 550 550 450 814 631 660 325 1598 1451 630 720 605 620 505 915 710 742 366 1797 1595 710 810 680 710 580 1050 814 851 419 2061 1770 800 940 700 830 590 1162 901 942 464 2282 1960 900 1065 785 945 665 1288 999 1044 514 2529 2200 1000 1176 886 1034 748 1427 1107 1157 570 2802 2420 1120 1325 992 1176 838 1637 1269 1327 654 3214 2700 1250 1439 1065 1291 917 1780 1380 1443 711 3498 3000 Maß- und Konstruktionsänderungen, dem technischen Fortschritt dienend, bleiben uns vorbehalten. We reserve the right to alter measurements without notice in case of technical improvements RD 0 RD 45 LG 0 LG 45 RD 90 RD 135 RD 180 LG 90 LG 135 LG 180 H = H2a R04.4 V2014/April RD 225 RD 270 LG 225 LG 270 H = H2b RD 315 H = H2a LG 315 37 38 R04.4 V2014/April 9a 8 5 3 12 CHEM 75 to 110 DD 17 9a Assembly and mounting Auf-und Einbau 7 8 9a 3 12 17 4 7 26 15 9a 11 1b 4 20 Fan Casing (PP type) Steel stand nut 01-11 Fan casing screw 01-7 01-9a Fan casing nut 01-5 Impeller plug Fan casing bolts 01-4 01-8 Impeller screw 01-3 Description Steel stand 01-1b Part Nos 21 16 26 15 11 01-26 01-21 01-20 01-17 01-16 01-15 01-12 Part Nos 1b Description Capacitor Steel stand screw and wash Electric motor Fan casing plug T-box cover T-box cover mounting screw Fan impeller 20 21 16 & R04.4 V2014/April 39 15 CHEM 125 to 200 DD Assembly and mounting Auf-und Einbau 14 16 Stählerner Bock Grundrahmen für DirektantriebFan Sechskantschrauben Sechskantmuttern Federringe und Muttern Gummidichtung Ventilatorgehäuse (PP typ) Gehäuserückschiebe Unterlegscheiben und Muttern 01-2b 01-4 01-5 01-7 01-8 01-9a 01-10 01-11 Beschreibung 13 01-1b Part Nos 12 9a 10 Description Washers and bolts Casing back cover Fan Casing (PP type) Rubber gasket Spring washers and nuts Hexagonal nuts Hexagonal bolts Base for direct drive Steel stand 17 8 01-25 01-24 01-20 01-17 01-16 01-15 01-14 01-13 01-12 Part Nos 1b Beschreibung 2b 20 Kranösen Montageposition der Federschwingungsdämpfer Elektromotor Kondensatablaufverschluß Laufradwellenabdeckung Schrauben Gehäuseeinlaufabdeckung Taper-Buchse Ventilatorlaufrad 4 11 24 Hoisting holes Spring Isolator mounting position Electric motor Drain plug Logo cap Bolts 5 Description Casing inlet cover Taper-Bushes Fan impeller 25 7 & 40 R04.4 V2014/April 15 14 CHEM 125 to 200 BD Assembly and mounting Auf-und Einbau 16 12 9a Grundrahmen für Riementrieb Schrauben und Muttern Sechskantschrauben Sechskantmutter Flanschlager Federringe und Muttern Gummidichtung Ventilatorgehäuse (PP typ) Gehäuserückschiebe Unterlegscheiben und Muttern Ventilatorlaufrad Taper-Buchse 01-2a 01-3 01-4 01-5 01-6a 01-7 01-8 01-9a 01-10 01-11 01-12 01-13 Beschreibung Stählerner Bock 13 17 01-1a Part Nos 10 8 Taper-Bushes Fan impeller Washers and bolts Casing back cover Fan casing(PP type) Rubber gasket Spring washers and nuts Flange bearing Hexagonal nuts Hexagonal bolts Bolts and nuts 4 25 Description Base for belt drive Steel stand 1a 11 01-25 01-24 01-23 01-22 01-21 01-20 01-19 01-18 01-17 01-16 01-15 01-14 22 19 18 7 Siegelring Montageposition der Federschwingungsdämpfer Riemenschutz Keil-Riemen und -Scheiben Sechskantschrauben, Unterlagscheiben und Muttern Elektromotor Motormontageplatte Gewindestange, Unterlagscheiben und Muttern Kondensatablaufverschluß Laufradwellenabdeckung Schrauben 24 Beschreibung Gehäuseeinlaufabdeckung 2a 6a Part Nos 3 5 Description 21 Seal ring Spring Isolator mounting position Belts guard Pulley and belts drive Hexagonal bolts,washers and nuts Electric motor Motor mounting plate Threaded rod,washers and nuts Drain plug Logo cap Bolts Casing inlet cover 20 23 & R04.4 V2014/April 41 CHEM 250 to 315 DD Assembly and mounting Auf-und Einbau 17 9a 16 Grundrahmen für DirektantriebFan Sechskantschrauben Sechskantmuttern Federringe und Muttern Gummidichtung Ventilatorgehäuse (PP typ) Gehäuserückschiebe Unterlegscheiben und Muttern 01-2b 01-4 01-5 01-7 01-8 01-9a 01-10 01-11 Beschreibung Stählerner Bock 01-1b Part Nos 13 12 10 Description 1b Washers and bolts Casing back cover Fan Casing (PP type) Rubber gasket Spring washers and nuts Hexagonal nuts Hexagonal bolts Base for direct drive Steel stand 4 2b 01-25 01-24 01-20 01-17 01-16 01-13 01-12 Part Nos 8 Beschreibung 24 25 Kranösen Montageposition der Federschwingungsdämpfer Elektromotor Kondensatablaufverschluß Laufradwellenabdeckung Taper-Buchse Ventilatorlaufrad 11 5 Hoisting holes Spring Isolator mounting position Electric motor Drain plug Logo cap Description 7 Taper-Bushes Fan impeller 20 & 42 R04.4 V2014/April 9a CHEM 250-315 BD Assembly and mounting Auf-und Einbau 17 16 13 12 Stählerner Bock Grundrahmen für Riementrieb Schrauben und Muttern Sechskantschrauben Sechskantmutter Flanschlager Federringe und Muttern Gummidichtung Ventilatorgehäuse (PP typ) Gehäuserückschiebe Unterlegscheiben und Muttern Ventilatorlaufrad Taper-Buchse 01-2a 01-3 01-4 01-5 01-6a 01-7 01-8 01-9a 01-10 01-11 01-12 01-13 Beschreibung 8 01-1a Part Nos 10 4 1a 25 19 5 Description Taper-Bushes Fan impeller Washers and bolts Casing back cover Fan casing (PP type) Rubber gasket Spring washers and nuts Flange bearing Hexagonal nuts Hexagonal bolts Bolts and nuts Base for belt drive Steel stand 3 11 2a 6a 01-25 01-24 01-23 01-22 01-21 01-20 01-19 01-18 01-17 01-16 Part Nos 22 Beschreibung 18 7 21 Siegelring Montageposition der Federschwingungsdämpfer Riemenschutz Keil-Riemen und -Scheiben Sechskantschrauben, Unterlagscheiben und Muttern Elektromotor Motormontageplatte Gewindestange, Unterlagscheiben und Muttern Kondensatablaufverschluß Laufradwellenabdeckung 24 20 23 Description Seal ring Spring Isolator mounting position Belts guard Pulley and belts drive Hexagonal bolts,washers and nuts Electric motor Motor mounting plate Threaded rod,washers and nuts Drain plug Logo cap & R04.4 V2014/April 43 CHEM 400 DD Assembly and mounting Auf-und Einbau 17 9a Grundrahmen für DirektantriebFan Sechskantschrauben Sechskantmuttern Federringe und Muttern Gummidichtung Ventilatorgehäuse (PP typ) Gehäuserückschiebe Unterlegscheiben und Muttern 01-2b 01-4 01-5 01-7 01-8 01-9a 01-10 01-11 Beschreibung Stählerner Bock 13 01-1b Part Nos 16 12 10 Description Washers and bolts Casing back cover Fan Casing (GRP type) Rubber gasket Spring washers and nuts Hexagonal nuts Hexagonal bolts Base for direct drive Steel stand 4 8 01-25 01-24 01-20 01-17 01-16 01-13 01-12 Part Nos 1b Beschreibung Kranösen Montageposition der Federschwingungsdämpfer Elektromotor Kondensatablaufverschluß Laufradwellenabdeckung Taper-Buchse Ventilatorlaufrad 2b 11 5 Taper-Bushes Description Hoisting holes Spring Isolator mounting position Electric motor Drain plug Logo cap 7 24 Fan impeller 25 20 & 44 R04.4 V2014/April 9a CHEM 400 BD 17 16 Assembly and mounting Auf-und Einbau 13 12 10 Schrauben und Muttern Sechskantschrauben Sechskantmutter Flanschlager Federringe und Muttern Gummidichtung Ventilatorgehäuse (PP typ) Gehäuserückschiebe Unterlegscheiben und Muttern Ventilatorlaufrad Taper-Buchse 01-4 01-5 01-6a 01-7 01-8 01-9a 01-10 01-11 01-12 01-13 Grundrahmen für Riementrieb 01-3 01-2a Beschreibung Stählerner Bock 8 01-1a Part Nos 4 1a 25 3 5 Taper-Bushes Fan impeller Washers and bolts Casing back cover Fan casing (PP type) Rubber gasket Spring washers and nuts Flange bearing Hexagonal nuts Hexagonal bolts Bolts and nuts Base for belt drive Description 19 Steel stand 11 2a 6a 01-25 01-24 01-23 01-22 01-21 01-20 01-19 01-18 01-17 01-16 Part Nos 22 Beschreibung 18 7 21 Siegelring Montageposition der Federschwingungsdämpfer Riemenschutz Keil-Riemen und -Scheiben Sechskantschrauben, Unterlagscheiben und Muttern Elektromotor Motormontageplatte Gewindestange, Unterlagscheiben und Muttern Kondensatablaufverschluß Laufradwellenabdeckung 24 20 23 Description Seal ring Spring Isolator mounting position Belts guard Pulley and belts drive Hexagonal bolts,washers and nuts Electric motor Motor mounting plate Threaded rod,washers and nuts Drain plug Logo cap & & SPECIFICATION Description Specified CHEMCO Chemical Resistant Centrifugal Fan Model CHEM 75 - 315 DD (Direct Driven) Offered Polypropylene Plastic Fan Fan Location Volume External static pressure Fan speed Brake-Input Motor-Output Full load Current A-weighted Sound power level Fan Weight Standard Colour - Grey RAL 7032 m3/h Pa min-1 kW kW A dB(A) Kg PANTONE warm Grey 1C Type of Casing Precision plastic injection moulded. CHEM 125 - 200 are suitable for dual rotation at any position, Injection moulded back plate & inlet cover can be removed for changing of rotation and maintenance. Fan casing comes with round straight outlet suitable for direct connection to flexible connector. No metal parts are situated in the airflow to eliminate the risk of corrosion. Casings with drain outlets at lowest point. Can be rotated to suit different discharge positions. c/w back draft rubber seal between casing and drive shaft. Polypropylene Type of Impeller Impellers are of Single Inlet Single Width (SISW) type. Precision plastic injection moulded with cast-in hub. The hubs are designed for use with taper-bushes to guarantee high reliability at high peripheral speeds. CHEM 90FC - 110FC are of forward curved blade. Polypropylene Radial Tip Backward Curve Performance tested AMCA 210 / ISO 5801 G2.5 of VDI 2060 Fan rated in accordance with: Impeller is statically and dynamically balanced in two planes. Fan Base and Support Hot-dipped galvanised Heavy gauge mild steel with maximum protection in the most adverse condition Type of Drive Direct Driven Motor Drive Shaft DIN17210-C45 or AISI C-1045 Solid type ground and polished to give tight, accurate bearing fit. Motor Bearing Grooved balls Fitted with two standard anti-friction bearings with acid proof seal. L10 life Electric motor Standard Flameproof Tropicalised Single Phase: Three Phase: Yes/No Yes/No Yes/No 220~240 volts 50/60 Hz 380~415 volts 50/60 Hz Special Accessories Required Anti-vibration spring mounting Inlet sleeve with clamping bands Splinter protection cover Yes/No Yes/No Yes/No Optional Requirement Temperature (ºC) Casing material Impeller material Fan Base and Support 80 PA / PC / PVC / PVDF PA / PC / PVC / PVDF SS304 / SS316 Flame Retardant Ultra Violet protection Yes/No Yes/No Anti-static Static dissipative Conductive Yes/No Yes/No Yes/No Electrostatic Discharge Maximum operating sound power level (dB re10-12W): Octave band mid frequency (Hz) Specified Offered R04.4 V2014/April 63 125 250 500 1K 2K 4K 8K 45 & SPECIFICATION Description Specified CHEMCO Chemical Resistant Centrifugal Fan Model CHEM 125 - 315BD (Belt Driven) Offered Polypropylene Plastic Fan Fan Location Volume External static pressure Fan speed Brake-Input Motor-Output Full load Current A-weighted Sound power level Fan Weight Standard Colour - Grey RAL 7032 m3/h Pa min-1 kW kW A dB(A) Kg PANTONE warm Grey 1C Type of Casing Precision plastic injection moulded. CHEM 125 - 200 are suitable for dual rotation at any position. Injection moulded back plate & inlet cover can be removed for changing of rotation and maintenance. Fan casing comes with round straight outlet suitable for direct connection to flexible connector. No metal parts are situated in the airflow to eliminate the risk of corrosion. Casings with drain outlets at lowest point. Can be rotated to suit different discharge positions. c/w back draft rubber seal between casing and drive shaft. Polypropylene Type of Impeller Impellers are of Single Inlet Single Width (SISW) type. Precision plastic injection moulded with cast-in hub. The hubs are designed for use with taper-bushes to guarantee high reliability at high peripheral speeds Performance tested Polypropylene Radial Tip Backward Curve AMCA 210 / ISO 5801 G2.5 of VDI 2060 Fan rated in accordance with: Impeller is statically and dynamically balanced in two planes. Fan Base and Support Hot-dipped galvanised Heavy gauge mild steel with maximum protection in the most adverse condition Type of Drive Belt Driven Drive Shaft DIN17210-C45 or AISI C-1045 Solid type ground and polished to give tight, accurate bearing fit. Bearing Belt driven flange mounted bearing housings type. Fitted with two standard anti-friction bearings with acid proof seal. L10 life Aluminium cast type Grooved balls Fan Drive ISO 4183-1980 ISO 4148 Fan and Motor Pulley drive come with taper bush type balanced to: Vee belts conform to: Electric motor Standard Flameproof Tropicalised Single Phase: Three Phase: Yes/No Yes/No Yes/No 220~240 volts 50/60 Hz 380~415 volts 50/60 Hz Special Accessories Required Anti-vibration spring mounting Motor guard Motor slide rails Belt guard Inlet sleeve with clamping bands Splinter protection cover Yes/No Yes/No Yes/No Yes/No Yes/No Yes/No Optional Requirement Temperature (ºC) Casing material Impeller material Stainless steel shaft Fan Base and Support 80 PA / PC / PVC / PVDF PA / PC / PVC / PVDF SS304 / SS316 SS304 / SS316 Flame Retardant Ultra Violet protection Yes/No Yes/No Anti-static Static dissipative Conductive Yes/No Yes/No Yes/No Electrostatic Discharge Maximum operating sound power level (dB re10-12W): Octave band mid frequency (Hz) 63 125 250 500 1K 2K 4K 8K Specified Offered 46 R04.4 V2014/April & SPECIFICATION Description Specified CHEMCO Chemical Resistant Centrifugal Fan Model CHEM 400DD (Direct Driven) Offered GRP / PP Plastic Fan Fan Location Volume External static pressure Fan speed Brake-Input Motor-Output Full load Current A-weighted Sound power level Fan Weight Standard Colour - Volcano Grey m3/h Pa min-1 kW kW A dB(A) Kg PANTONE 430 Type of Casing Fibre Glass-Reinforced Plastic (GRP/FRP), Vinyl ester grade. Come with Injection moulded PP back plate can be removed for changing of rotation and maintenance. Straight outlet flange for easy duct connection. Max. Temp. 100°C. No metal parts are situated in the airflow to eliminate the risk of corrosion. Casings with drain outlets at lowest point. Casing can be rotated to suit different discharge positions. C/W back draft rubber seal between casing and drive shaft. Type of Impeller Impellers are of Single Inlet Single Width (SISW) type. Precision plastic injection moulded with cast-in hub. The hubs are designed for use with taper-bushes to guarantee high reliability at high peripheral speeds GRP Polypropylene Radial Tip Backward Curve Performance tested AMCA 210 / ISO 5801 G2.5 of VDI 2060 Fan rated in accordance with: Impeller is statically and dynamically balanced in two planes. Fan Base and Support Hot-dipped galvanised Heavy gauge mild steel with maximum protection in the most adverse condition Type of Drive Direct Driven Motor Drive Shaft DIN17210-C45 or AISI C-1045 Solid type ground and polished to give tight, accurate bearing fit. Motor Bearing Grooved balls Fitted with two standard anti-friction bearings with acid proof seal. L10 life Electric motor Standard Flameproof Tropicalised Single Phase: Three Phase: Yes/No Yes/No Yes/No 220~240 volts 50/60 Hz 380~415 volts 50/60 Hz Special Accessories Required Anti-vibration spring mounting Inlet sleeve with clamping bands Splinter protection cover Yes/No Yes/No Yes/No Optional Requirement Temperature (ºC) Casing material Impeller material Fan Base and Support 80 PA / PC / PVC / PVDF PA / PC / PVC / PVDF SS304 / SS316 Flame Retardant Ultra Violet protection Yes/No Yes/No Anti-static Static dissipative Conductive Yes/No Yes/No Yes/No Electrostatic Discharge Maximum operating sound power level (dB re10-12W): Octave band mid frequency (Hz) Specified Offered R04.4 V2014/April 63 125 250 500 1K 2K 4K 8K 47 & SPECIFICATION Description Specified CHEMCO Chemical Resistant Centrifugal Fan Model CHEM 400BD (Belt Driven) Offered GRP / PP Plastic Fan Fan Location Volume External static pressure Fan speed Brake-Input Motor-Output Full load Current A-weighted Sound power level Fan Weight Standard Colour - Volcano Grey m3/h Pa min-1 kW kW A dB(A) Kg PANTONE 430 Type of Casing Fibre Glass-Reinforced Plastic (GRP/FRP), Vinyl ester grade. Come with Injection moulded PP back plate can be removed for changing of rotation and maintenance. Straight outlet flange for easy duct connection. Max. Temp. 100°C. No metal parts are situated in the airflow to eliminate the risk of corrosion. Casings with drain outlets at lowest point. Casing can be rotated to suit different discharge positions. C /W back draft rubber seal between casing and drive shaft. GRP Type of Impeller Impellers are of Single Inlet Single Width (SISW) type. Precision plastic injection moulded with cast-in hub. The hubs are designed for use with taper-bushes to guarantee high reliability at high peripheral speeds Performance tested Polypropylene Radial Tip Backward Curve AMCA 210 / ISO 5801 G2.5 of VDI 2060 Fan rated in accordance with: Impeller is statically and dynamically balanced in two planes. Fan Base and Support Hot-dipped galvanised Heavy gauge mild steel with maximum protection in the most adverse condition Type of Drive Belt Driven Drive Shaft DIN17210-C45 or AISI C-1045 Solid type ground and polished to give tight, accurate bearing fit. Bearing Belt driven flange mounted bearing housings type. Fitted with two standard anti-friction bearings with acid proof seal. L10 life Aluminium cast type Grooved balls Fan Drive ISO 4183-1980 ISO 4148 Fan and Motor Pulley drive come with taper bush type balanced to: Vee belts conform to: Electric motor Standard Flameproof Tropicalised Single Phase: Three Phase: Yes/No Yes/No Yes/No 220~240 volts 50/60 Hz 380~415 volts 50/60 Hz Special Accessories Required Anti-vibration spring mounting Motor guard Motor slide rails Belt guard Inlet sleeve with clamping bands Splinter protection cover Yes/No Yes/No Yes/No Yes/No Yes/No Yes/No Optional Requirement Temperature (ºC) Casing material Impeller material Stainless steel shaft Fan Base and Support 80 PA / PC / PVC / PVDF PA / PC / PVC / PVDF SS304 / SS316 SS304 / SS316 Flame Retardant Ultra Violet protection Yes/No Yes/No Anti-static Static dissipative Conductive Yes/No Yes/No Yes/No Electrostatic Discharge Maximum operating sound power level (dB re10-12W): Octave band mid frequency (Hz) 63 125 250 500 1K 2K 4K 8K Specified Offered 48 R04.4 V2014/April & SPECIFICATION Description Specified CHEMCO Chemical Resistant Centrifugal Fan Model CHEM 450 - 710DD (Direct Driven) Offered GRP / PP Plastic Fan Fan Location Volume External static pressure Fan speed Brake-Input Motor-Output Full load Current A-weighted Sound power level Fan Weight Standard Colour - Volcano Grey m3/h Pa min-1 kW kW A dB(A) Kg PANTONE 430 Type of Casing Fibre Glass-Reinforced Plastic (GRP/FRP), Vinyl ester grade. Come with Injection moulded PP back plate can be removed for changing of rotation and maintenance. Straight outlet flange for easy duct connection. Max. Temp. 100°C. No metal parts are situated in the airflow to eliminate the risk of corrosion. Casings with drain outlets at lowest point. Casing can be rotated to suit different discharge positions. C/W back draft rubber seal between casing and drive shaft. GRP Type of Impeller Impellers are of Single Inlet Single Width (SISW) type. Precision plastic injection moulded with cast-in hub. The hubs are designed for use with taper-bushes to guarantee high reliability at high peripheral speeds Polypropylene Radial Tip Backward Curve Performance tested AMCA 210 / ISO 5801 G2.5 of VDI 2060 Fan rated in accordance with: Impeller is statically and dynamically balanced in two planes. Fan Base and Support Hot-dipped galvanised Heavy gauge mild steel with maximum protection in the most adverse condition Type of Drive Direct Driven Motor Drive Shaft DIN17210-C45 or AISI C-1045 Solid type ground and polished to give tight, accurate bearing fit. Motor Bearing Grooved balls Fitted with two standard anti-friction bearings with acid proof seal. L10 life Electric motor Standard Flameproof Tropicalised Three Phase: Yes/No Yes/No Yes/No 380~415 volts 50/60 Hz Special Accessories Required Yes/No Yes/No Yes/No Yes/No Inspection Door/Cover Anti-vibration spring mounting Inlet sleeve with clamping bands Splinter protection cover Optional Requirement Temperature (ºC) Casing material Impeller material Fan Base and Support 80 PA / PC / PVC / PVDF PA / PC / PVC / PVDF SS304 / SS316 Flame Retardant Ultra Violet protection Yes/No Yes/No Anti-static Static dissipative Conductive Yes/No Yes/No Yes/No Electrostatic Discharge Maximum operating sound power level (dB re10-12W): Octave band mid frequency (Hz) Specified Offered R04.4 V2014/April 63 125 250 500 1K 2K 4K 8K 49 & SPECIFICATION Description Specified CHEMCO Chemical Resistant Centrifugal Fan Model CHEM 450 - 1250BD (Belt Driven) Offered GRP / PP Plastic Fan Fan Location Volume External static pressure Fan speed Brake-Input Motor-Output Full load Current A-weighted Sound power level Fan Weight Standard Colour - Volcano Grey m3/h Pa min-1 kW kW A dB(A) Kg PANTONE 430 Type of Casing GRP Fibre Glass-Reinforced Plastic (GRP/FRP), Vinyl ester grade. Come with Injection moulded PP back plate can be removed for changing of rotation and maintenance. Straight outlet flange for easy duct connection. Max. Temp. 100°C. No metal parts are situated in the airflow to eliminate the risk of corrosion. Casings with drain outlets at lowest point. Casing can be rotated to suit different discharge positions. C /W back draft rubber seal between casing and drive shaft. Type of Impeller Impellers are of Single Inlet Single Width (SISW) type. Precision plastic injection moulded with cast-in hub. The hubs are designed for use with taper-bushes to guarantee high reliability at high peripheral speeds Performance tested Polypropylene Radial Tip Backward Curve AMCA 210 / ISO 5801 G2.5 of VDI 2060 Fan rated in accordance with: Impeller is statically and dynamically balanced in two planes. Fan Base and Support Hot-dipped galvanised Heavy gauge mild steel with maximum protection in the most adverse condition Type of Drive Belt Driven Drive Shaft DIN17210-C45 or AISI C-1045 Solid type ground and polished to give tight, accurate bearing fit. Bearing Belt driven flange mounted bearing housings type. Fitted with two standard anti-friction bearings with acid proof seal. L10 life Aluminium cast type Grooved balls Fan Drive ISO 4183-1980 ISO 4148 Fan and Motor Pulley drive come with taper bush type balanced to: Vee belts conform to: Electric motor Standard Flameproof Tropicalised Three Phase: Yes/No Yes/No Yes/No 380~415 volts 50/60 Hz Special Accessories Required Inspection Door/Cover Anti-vibration spring mounting Motor guard Motor slide rails Belt guard Inlet sleeve with clamping bands Splinter protection cover Manual / Semi / Automatic greasing system Yes/No Yes/No Yes/No Yes/No Yes/No Yes/No Yes/No Yes/No Optional Requirement Temperature (ºC) Casing material Impeller material Stainless steel shaft Fan Base and Support 80 PA / PC / PVC / PVDF PA / PC / PVC / PVDF SS304 / SS316 SS304 / SS316 Flame Retardant Ultra Violet protection Yes/No Yes/No Anti-static Static dissipative Conductive Yes/No Yes/No Yes/No Electrostatic Discharge Maximum operating sound power level (dB re10-12W): Octave band mid frequency (Hz) 63 125 250 500 1K 2K 4K 8K Specified Offered 50 R04.4 V2014/April & Air in Motion - Wolter Fans - www. wolterfans.de Reference: R04.4, V2014/April, Printed in April, 2014 Dongguan Wolter Chemco Ventilation Ltd.(Wolter Asia) • Shipai / Dongguan / Guangdong / China Tel. (+86)769 86557298 • Fax (+86)769 86557278 • www.wolterfans.com • [email protected]