Document 6463983

Transcription

Document 6463983

LEXUS
ES 350
2013–
PREPARATION
TVIP V4
REMOTE ENGINE STARTER (RES)
Part #: PT398-33131
Will not program with Techstream Lite.
RES ECU Bracket
RES ECU
x1
x1
V4 Harness
Wire Tie
M6 Nut
x1
x1
Foam Tape
x10
Engine Room
*
x1
x2
PT398-60088
x2
x1
PT398-60086
PT398-89100-SS
%&'*
Key Tag
Owner’s Guide
x1
PT398-00070-EL
Service Part #’s
+/
Safety Glasses
Safety Gloves
(Optional)
Techstream
Use latest version on TIS (Do not use Techstream Lite)
Screwdriver
#2 Phillips
Nylon Panel Removal Tool
e.g. Panel Pry Tool #1 Toyota SST# 00002-06001-01
Utility Knife
!
"
Side Cutters
Pliers
Needle Nose
Socket
10mm, Extension
Torque Wrench
! "$
Tape
Clear, Electrical
Issue: A 04/30/12
Cleaner
VDC Approved Cleaner
Glass Cleaner
Household Glass Cleaner
Page 1 of 23
LEXUS
ES 350
2013–
PREPARATION
TVIP V4
$"
I. Preparation ............................................................................................................................ 1 – 3
1. 5&:& ................................................................................................................................................2
2. Wire Routing Overview .......................................................................................................................................3
II. Procedure ............................................................................................................................4 – 2 0
1.
2.
3.
4.
6.
7.
;<=> .........................................................................................................................................4
RES ECU Preparation and Installation. ..............................................................................................................8
V4 Harness Installation. ....................................................................................................................................10
Registration Preparation ...................................................................................................................................13
Registration . .....................................................................................................................................................14
Complete the Installation. .................................................................................................................................19
5* .................................................................................................................................................20
III. Checklist ........................................................................................................................... 2 1 – 2 3
1. Accessory Function Checks ..............................................................................................................................21
2. Vehicle Function Checks ...................................................................................................................................22
()
Do not proceed until process
<=&\
Follow steps carefully to
avoid damaging the Vehicle
or Accessory
Use caution to avoid injury.
Used in Figures to call attention
&\=_=&&=&
for the process.
Highlights a change in
installation with respect to
previous issue.
%&$"'
:/?'<<==&&/&&
occur to the vehicle. The installation of this accessory should follow approved
guidelines to ensure a quality installation.
5</=&/<@!==&J&==Q
document.
This document covers such items as:
;<=&=&/&=&Y?==<==
Safety (eye protection, checking torque procedure, etc.)
;<=>Z[\&Y\&=
]==:&\&>Z[=&=&
connector removal, etc.)
Please see your LEXUS dealer for a copy of this document.
I
Indicates
that torque is related
tto safety.
;&Y`==?&\
xx
%5&=&/
Issue: A 04/30/12
Page 2 of 23
*+,!.
Vehicle
A
Description
8P White
-
24P White
(for RES ECU)
M
-
1P White
(for Registration)
N
-
1P White
(for Registration)
W
-
White Tape Marker
Z
-
RES ECU
ES 350
E
LEXUS
TVIP
PREPARATION
Issue: A 04/30/12
LEXUS ES350 RES
Z
E
2013–
Page 3 of 23
W
A
TVIP V4
."+,//22+4
N
M
LEXUS
ES 350
2013–
PROCEDURE
$%,//2
TVIP V4
1
PS Step Cover
2
PS Cowl Cover
3
PS Dash Side Trim
4
PS Dash Side Cover
Glove Box Under Cover
6
!
(Do not disconnect Knee
Airbag’s connectors)
7
Glove Box Trim
8
Glove Box
8
7
3
4
6
2
1
Disconnect all Corresponding
Connectors.
10mm Socket
Fig. 1-1
64 $%4
a. Place the Vehicle in Park with
the Parking Brake set.
Disconnect the Negative
Battery Terminal.
&<:&&
'z<
same position.
7,;
Do not touch the
Positive Terminal.
Issue: A 04/30/12
Page 4 of 23
LEXUS
ES 350
2013–
PROCEDURE
TVIP V4
Fig. 1-2
c.
Remove the Passenger’s
Side Step Cover.
Fig. 1-3
d. Remove the Passenger’s
Side Cowl Cover.
Remove 1 Nut.
Fig. 1-4
e. Remove the Passenger’s
Side Dash Side Trim.
Apply Protective Tape on Pry area.
Issue: A 04/30/12
Page 5 of 23
LEXUS
ES 350
2013–
PROCEDURE
TVIP V4
f.
Fig. 1-5
Remove the Passenger’s
Side Dash Cover.
Apply Protective Tape on Pry area.
Fig. 1-6
g. Dislodge the Glove Box
Under Cover.
Disconnect Vehicle Connector.
10mm Socket, Extension, Nylon Panel Removal Tool
Fig. 1-7
h. Dislodge the Passenger’s
!=/
Remove 3 Bolts.
7,;
Do not disconnect the
Vehicle’s Connector.
Issue: A 04/30/12
Page 6 of 23
LEXUS
ES 350
2013–
PROCEDURE
TVIP V4
i.
Fig. 1-8
%\<!?
or the like and place it on top
&<5;J&|
7,;
Prevent stress on the
!%
Phillips Screwdriver
Fig. 1-9
Fig. 1-10
Issue: A 04/30/12
Page 7 of 23
j.
Remove 2 Screws from the
&&&<}&Y&|
k.
Open the Glove Box.
l.
Remove the Glove Box Trim.
LEXUS
ES 350
2013–
PROCEDURE
TVIP V4
m. Dislodge the Glove Box.
Phillips Screwdriver, Nylon Panel Removal Tool
Fig. 1-11
Needle Nose Pliers
Fig. 1-12
Remove 3 Screws.
n. Remove the Vehicle’s
Harness clamp on the top
left side of the Glove Box.
o. Disconnect the Vehicle’s
Connectors.
p. Remove the Glove Box
Lamp.
q. Remove the Glove Box.
Fig. 2-1
<4 ==7
4
a. Attach the RES ECU Bracket
to the RES ECU as shown.
Issue: A 04/30/12
Page 8 of 23
LEXUS
ES 350
2013–
PROCEDURE
TVIP V4
Cut the Foam Tape in half.
Utility Knife
Fig. 2-2
"Z~&5\
"Z~&5\
c.
Fig. 2-3
10mm Socket
Fig. 2-4
Attach the Foam Tapes to the
RES ECU as shown.
d. Install the RES ECU using
the supplied Nut.
;,=
Make sure the Guide Pin
is seated correctly and Verify that
the Nut is tightened securely.
Issue: A 04/30/12
Page 9 of 23
LEXUS
ES 350
2013–
PROCEDURE
Fig. 3-1
Fig. 3-2
TVIP V4
>4 ?+4
a. Plug in the V4 White 24P
Connector to the RES ECU.
Connect the V4 White 8P
Connector to the Vehicle’s
8P Pre-Connector.
c.
Side Cutters
Fig. 3-3
2
Secure the V4 Harness and
the 8P Connectors to the
Vehicle Harness using
1 Wire Tie.
d. Secure the V4 Harness to
the Vehicle Harness using
1 Wire Tie.
1
Issue: A 04/30/12
Page 10 of 23
LEXUS
ES 350
2013–
PROCEDURE
Side Cutters
Fig. 3-4
TVIP V4
e. Secure the V4 Harness White
Tape Marker to the Vehicle
Harness using 1 Wire Tie.
3
f.
Fig. 3-5
Route the V4 Harness
toward the Passenger’s
Side Cowl area.
g. Secure the V4 Harness to the
HVAC Wire Hooks along with
the Vehicle Harness.
Side Cutters
Fig. 3-6
h. Secure the V4 Harness to
1 Wire Tie.
Place Wire Tie near the Vehicle
=<
Rotate the Ratchet End of the
Wire Tie as shown.
i.
4
Secure the V4 Harness to
1 Wire Tie.
Rotate the Ratchet End of the
Wire Tie as shown.
5
Issue: A 04/30/12
Page 11 of 23
LEXUS
ES 350
2013–
PROCEDURE
Side Cutters
TVIP V4
j.
1 Wire Tie.
k.
1 Wire Tie.
Fig. 3-7
6
Side Cutters
Fig. 3-8
7
Issue: A 04/30/12
Page 12 of 23
LEXUS
ES 350
2013–
PROCEDURE
10mm Socket, Extension, Torque Wrench, Phillips Screwdriver
Fig. 4-1
TVIP V4
?4 )4
a. [<;<=
except for the Passenger’s
Cowl and Step Covers.
;,=
When reinstalling Knee
!?/&<<
&& (10 Nm).
=@A
That all Connectors are
plugged in.
=@A
5<_&<
properly, with no uneven gaps.
Do not Install
Fig. 4-2
Verify that the Short Pin is
installed.
If not install now.
Issue: A 04/30/12
Page 13 of 23
LEXUS
ES 350
2013–
PROCEDURE
z"
10mm Socket
TVIP V4
B4 )4
a. Open the Hood.
Temporarily reconnect the
Y:
7,;
Do not touch the
Positive Terminal.
c.
z~
Locate the 1P RES
Diagnostic Connectors in
the Passenger’s Side Cowl
Area and connect them.
;,=
Once connected you will
have 10 minutes to complete this
=&\
d. Close all doors.
z
e. Place the Vehicle in Park (P)
or Neutral (N) position.
f.
5
X
OFF
ACC
:=<@]&\Q
/&&&
times.
;,=
One cycle consists of:
!==&
This is equivalent to pressing
<@]&\Q/&
14 times.
ON
;,=
Do not apply Brake pedal.
(,,
For the Hazard Lights to
Flash Once.
Issue: A 04/30/12
Page 14 of 23
LEXUS
ES 350
2013–
PROCEDURE
TVIP V4
g. Start the Engine.
z
h. After 10 seconds stop the
Engine.
(,,
For the Hazard Lights to
Flash Once.
@+,=7=@(=
5<*<<5<
Times.
ON
OFF
Disconnect the V4 Harness’s 1P
RES Diagnostic Connectors.
Start again from step c.
Techstream
z
7,;
Techstream Lite will
not work for this section, use the
5=<&&&?*
i.
Connect the Techstream
&&&?&<;<=
Diagnostic Port.
j.
With the Smart Key in your
possession, press the
@]&\Q/&
twice to select the Ignition
@Q\&&
k.
Start the TIS Techstream
!\\=&==?&
the shortcut located on the
Desktop.
l.
:=?@:&=&;<=Q
z
Issue: A 04/30/12
Page 15 of 23
LEXUS
ES 350
2013–
PROCEDURE
z
TIS techstream
File Function
Setup
TIS
User
Help
Connect to Vehicle
Vehicle Connection Wizard(S301-04)
TIS
techstream
Select the Information and press Next
Open Scan Data File
TVIP V4
m. :&_<<&&
displayed on the Vehicle
Connection Wizard is correct
for the vehicle. If not verify
that the Techstream is
properly connected.
Required Information:
Launch TIS
Division:
XXXXXX
Model:
XXXXXXXXX
20XX
New Users Demo
Check for Scantool
Updates
Model Year:
Generic OBD II
Software
Registration
User/Language
Selection
Engine:
XXXXXXXX
Option:
XXXXXXXX
n. Select option depending on
;<=\=_=&
o. :=?@|Q
Log Out
Optional Information:
xxxxxxxxxxxxxxxxxxx
VIN:
ABS
Memo:
Manual
Help
<Back
Next>
Cancel
Ver x.xx.xxx
p. =@!==Q
z
q. Click
.
TIS techstream - 10645
File Function Setup TIS
System Select
User Help
Stored Data
System Selection Menu
Select desired system and then press Live Data to access the ECU.
Body or not responding.
Back Door
isMain
unsupported
Air
Conditioner
SRS Airbag
Note:
An astrisk (*) indicates
a system that
Combination Meter Main Body
*Sliding Roof
Tilt&Telescopic
Health Check
All ECUs
Powertrain
Chassis
Air Conditioner
SRS Airbag
Combination Meter Smart Access
Customize
Setting
*Accessory Gateway *Driver Door
Combination Meter Mirror
D Door Motor
Sliding Roof
*Passenger Door
Driver Seat
Occupant Detection
Body Electrical
Main Body
Occupant Detection
Back Door
D Door Motor
Sliding Roof
ECU
Reprogramming
CAN
Bus. Check
Print
Close
S601-03
Generic English
DLC3
z
r.
:=?&@Q
s.
=@]::&/=&
J>[&Q
t.
Click
System Select
User Help
Stored Data
Customize
Utility Selection Menue
Select desired Utility and then press Next button.
Trouble Codes
Custimize
ECU Communication ID Registration
Smart Code Registration
Communication Check(Key Diag Mode)
Smart Code Erasure
Smart Code Reset
Data List
Active Test
Monitor
Utility
Print
Close
S601-03
Issue: A 04/30/12
Generic English
DLC3
Page 16 of 23
.
LEXUS
ES 350
2013–
PROCEDURE
TVIP V4
u. :=?@|Q
z"$
System Select
User Help
Stored Data
Custom ize
ECU
Select desired Utility and
thenCommunication
press Next button. ID Registration (SMRT-13-001)
Welcome to the ECU Communication
ID
wizard.
Smart Code Erasure
Trouble Codes
Custimize
Registration
Code Reset
This function is used to performSmart
the “hand
shake” procedure.
Data List
Confirm the following conditions:
Active Test
-The Engine is ON (IG)
-Smart Cancel Function is OFF
Monitor
Utility
Next>
Cancel
Print
Close
S601-03
Generic English
DLC3
v.
z""
w. :=?@|Q
System Select
User Help
Stored Data
Custom ize
Utility Selection
Menue
ECU Communication
Trouble Codes
=@[&]
Q
ID Registration (SMRT-13-002)
Custimize
IDIDCode
Box and
ECU Communication
Registration
Steering Lock
Smart Code Erasure
Smart Code Reset
Remote Engine Starter
Data List
Active Test
Monitor
Utility
Make a selection and press Next to “hand
shake” the selected ECU’s
<Back
Next>
Cancel
Print
Close
S601-03
Generic English
DLC3
z"~
,;@K
That the ECU
Communication ID was
completed successfully.
System Select
User Help
Stored Data
x.
Custom ize
ECU
Select desired Utility and
thenCommunication
press Next button. ID Registration (SMRT-13-002)
Trouble Codes
Data List
Custimize
Smart Code Erasure
Smart Code Reset
Communication ID registration for Remote
Engine Starter is complete.
Active Test
Monitor
Utility
Exit
Print
Close
S601-03
Issue: A 04/30/12
Generic English
DLC3
Page 17 of 23
:=?@]|Q
LEXUS
ES 350
2013–
PROCEDURE
z"
TVIP V4
y.
Click
z.
Exit the vehicle.
.
System Select
User Help
Stored Data
Customize
Trouble Codes
Custimize
Smart Code Erasure
Smart Code Reset
Data List
Active Test
Monitor
Utility
Print
Close
S601-03
Generic English
DLC3
z"
aa. Close the Hood.
Look for the Hazards to
<5'=
@+,=7=@(=
5<*<<5<
Times.
Disconnect the V4 Harness’s 1P
RES Diagnostic Connectors.
Start again from step c.
Fig. 5-15
ac. After a successful
Registration, disconnect
the 1P RES Diagnostic
Connectors.
ad. Secure the 1P RES
Diagnostic Connectors with
RES Diagnostic Wires to
Electrical Tape.
Issue: A 04/30/12
Page 18 of 23
LEXUS
ES 350
2013–
PROCEDURE
Fig. 6-1
TVIP V4
N4 4
a. <<
Vehicle.
;][J5<\_&<
properly, with no uneven gaps.
;][JThat all Connectors are
plugged in.
!*[]!>J5!**]>
Torque Wrench
Fig. 6-2
Position the Negative Battery
:<&=&
position.
5<</&
7,;
Do not touch the
positive terminal.
c.
Clean up and Remove trash.
d. \&=Y
place the Owner’s Manual in
the Glove Box.
Issue: A 04/30/12
Page 19 of 23
LEXUS
ES 350
2013–
PROCEDURE
Fig. 7-1
TVIP V4
Q4 )($4
a. Using VDC approved cleaner
and cleaning method, clean
the area indicated in the
Engine Compartment Cover.
Attach the Engine Room
%*<&'
7,;
Do not touch the
adhesive surface.
c.
Attach the Key Tag.
Fig. 7-2
REPEAT: step c with the other
Smart Key.
Fig. 7-3
Clear Tape
10 mm
e. Use a piece of Clear Tape
&<*&
\&=Y=?
PA R A L L E L
7,;
Do not touch the
adhesive surface.
MOLDING
f.
" ;G
+I
C
T
LS
BE
EE
A
+
T
RL
T,
+E
;
T
,
IG
T,
AL
;
T,
IG
PA R A L L E L
W
AL
+,
T,
W
MOLDING
+,
Issue: A 04/30/12
d. Use Household Glass
Cleaner to clean the inside
of the Front Door Window.
!=<<*<&'
;,=
Make sure to Align
according to Etching or Other
*
REPEAT: steps d-f with the other
Window.
Page 20 of 23
LEXUS
ES 350
2013–
PROCEDURE
TVIP V4
%@!]
:&<<&&<Y<==&&&=<<Y<@Q?\&&<\?
??/<;<=&
"
(]@
1
<&=&&&=?/&'=
within 2 seconds, then press and hold the
&=?/&&=&
5<<<<=&
The engine starts.
5<<<<\&"$=&
2
With the engine running, pull the hood
release handle.
The engine stops.
5<<<<&=
The security alarm triggers. (Only if equipped with
OE Factory Alarm, not Genuine Accessory alarm,
and only if armed)
;,=
Some Vehicles may require you to exit
the Vehicle and pull up on the Hood.
3
&Y<<Y&/&@Q?
Attempt to start the Vehicle using
the remote.
Issue: A 04/30/12
The engine does not start.
Page 21 of 23
LEXUS
ES 350
2013–
CHECKLIST – these points MUST be checked to ensure a quality installation.
TVIP V4
@!]
@!
@!
=

>&Z:&/*<

Horn

Starter

Z'=<J/&

Lamp Failure Sensor

Seat Belt Warning Light

Air Bag Warning Light

If the warning light remains on, it may
indicate a system malfunction.

Gauges
ABS Light (if equipped)
5=?Z?:&&*<+/\\
If the warning light remains on, it may indicate
a system malfunction.
Tire Pressure Monitoring System
(TPMS).
Prior to TPMS activation and Pre-delivery Service
(PDS) of the Vehicle the TPMS light will blink
when IG is turned on.
After TPMS activation and PDS of the Vehicle the
TPMS light will illuminate for a few seconds and
go off when IG is turned on.
Cruise Control Light (if equipped)
7)K]"2)4

5/?Z5Z*<+/\\
Brake Lights
Backup Lights

Tail Lights
Daytime Running Lights (if equipped)
Marker Lights
Clearance Sonar (if equipped)
=)^_`,;4

Hazard Lights
Head Light
High Beams
Power Side Mirrors (if equipped)
Power Sliding Door (if equipped)
Issue: A 04/30/12

Page 22 of 23
Turn Signal Lights
Fog Lights (if equipped)
!==&:&&ZJ/&
(if equipped)
Convenience Memory Settings (if equipped)
Rear Sunshade (if equipped)
LEXUS
ES 350
2013–
CHECKLIST – these points MUST be checked to ensure a quality installation.

@!
&'/Z&&[&&+/\\
Clock (if equipped)
!/&Z;&+/\\
Steering Wheel Audio Control (if equipped)
Blind Spot Monitor (BSM) (if equipped)
Side Mirror Defogger (if equipped)
Massage Seats (if equipped)
Glove Box Light (if equipped)
Power Locks (if equipped)
Power Seats (if equipped)

Remove the short pin after Function check.
Check with your Port/Dealer to see if this step is necessary.
Issue: A 04/30/12
@!
&%\Z%<
Front Windshield Defogger (if equipped)
TVIP V4
Page 23 of 23
[%\Z%<+/\\
Rollover Side Curtain Air Bag Switch (RSCA)
(if equipped)
Navigation System (if equipped)
HVAC
Steering Wheel Heater (if equipped)
Rear Window Defogger (if equipped)
Accessory Power Socket (if equipped)
Z;+/\\
Passenger Air Bag Switch (if equipped)
Trunk Cancel Switch (if equipped)
Power Windows (if equipped)
Key Sensor Buzzer