Seven function digital multimeter 98025 Set up and operating inStructionS

Transcription

Seven function digital multimeter 98025 Set up and operating inStructionS
Seven function digital
multimeter
98025
Set up And Operating Instructions
Distributed exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
Save this manual.
Copyright© 2008 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any
artwork contained herein may be reproduced in any shape or form without the express written
consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described
herein. Tools required for assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Save This Manual
Keep this manual for the safety
warnings and precautions, assembly,
operating, inspection, maintenance and
cleaning procedures. Write the product’s
serial number in the back of the manual
near the assembly diagram (or month and
year of purchase if product has no number). Keep this manual and the receipt in
a safe and dry place for future reference.
Important SAFETY
Information
In this manual, on the labeling,
and all other information
provided with this product:
This is the safety alert
symbol. It is used to alert
you to potential personal
injury hazards. Obey all
safety messages that
follow this symbol to avoid
possible injury or death.
DANGER indicates
a hazardous
situation which, if not
avoided, will result in death or
serious injury.
NOTICE is used to
address practices
not related to personal injury.
CAUTION, without
the safety alert
symbol, is used to address
practices not related to
personal injury.
General Safety Rules
WARNING Read all safety
warnings and instructions.
Failure to follow the warnings and
instructions may result in electric
shock, fire and/or serious injury.
Save all warnings and
instructions for future
reference.
1. Electrical shock can cause death
or injury! NEVER TOUCH exposed
conductors of electricity.
2. Inspect the Multimeter before use. In
addition to a general inspection, look
specifically for:
a.Pay special attention to the insulation protecting the connectors.
b.Check the leads for exposed metal,
damaged insulation, and continuity.
c.Replace damaged test lead immediately, before use.
WARNING indicates
3. Do not use the multimeter if:
a hazardous
a.The test lead is damaged in any
situation which, if not
way.
avoided, could result in death
or serious injury.
b.The battery is low.
CAUTION, used
with the safety alert
symbol, indicates a
hazardous situation which, if
not avoided, could result in
minor or moderate injury.
c.Near any explosive gasses or
fumes.
d.Any abnormal operation is detected.
(If in doubt about the condition of
the meter, have it serviced.)
e.The battery cover is open.
SKU 98025
For technical questions, please call 1-800-444-3353.
Page 2
4. This meter should be powered only by 15. This product contains or produces
a single, correctly installed 9V battery.
chemicals, including lead, known to
the State of California to cause cancer
5. Use caution when working near voltand birth defects (or other reproducages above 30 VAC rms, 42 VAC
tive harm).
peak, or 60 VDC. Voltages this high
(California Health & Safety Code §
present a risk of electric shock.
25249.5, et seq.)
6. Disconnect the circuit’s power before 16. Do not test voltage on circuits higher
connecting the meter in series, when
than 750 volts AC or 1000 volts DC.
measuring current.
This type of testing should only be
7. Connect the common (COM) test lead
first and disconnect it last.
17.
8. Hold the probes with fingers behind
guards.
18.
9. Avoid electrical shock. Use
extreme caution when working near
uninsulated conductors or bus bars.
Prevent body contact with grounded
surfaces such as pipes, radiators,
ranges, and cabinet enclosures when
testing voltages.
10.
11.
12.
13.
done by a qualified electrician.
Do not test current on circuits higher
than 200 mA.
Store idle equipment. When not in
use, meters must be stored in a dry
location to decrease exposure to
moisture. Lock up meters and keep
out of reach of children.
19. Dress properly. Protective, electrically
nonconductive clothes and nonskid
footwear are recommended when
working.
Observe work area conditions. Do not
test voltages in damp or wet locations. 20. Wear ANSI-approved impact safety
Don’t expose to rain. Keep work area
goggles.
clean and well lit.
21. Only use accessories intended for
Keep children away. Children must
use with this meter.
never be allowed in the work area.
22. The warnings, cautions, and instrucStay alert. Watch what you are doing,
tions discussed in this instruction
use common sense. Do not operate
manual cannot cover all possible conany meter when you are tired.
ditions and situations that may occur.
It must be understood by the operator
Do not operate meter if under the
that common sense and caution are
influence of alcohol or drugs. Read
factors which cannot be built into this
warning labels on prescriptions to
product, but must be supplied by the
determine if your judgment or reflexes
operator.
are impaired while taking drugs. If
there is any doubt, do not operate the 23. Avoid damaging meter. Use only as
meter.
specified in this manual.
14. Due to the danger inherent in such
work, we strongly recommend that
only a licensed electrician work on
high-voltage or other potentially dangerous circuits.
SKU 98025
24. Prior to testing, resistance, diodes, or
continuity; disconnect all power to the
circuit and discharge all high-voltage
capacitors.
For technical questions, please call 1-800-444-3353.
Page 3
25. Performance of this meter may vary
depending on battery condition.
26. Use the proper settings, terminals,
techniques, and range for the tests
performed. Always start with the
range stated in the instructions.
27. Do not apply voltage to the Test
Leads when the Multimeter is in the
Ohms testing setting. Damage can
occur to the multimeter.
28. Do not switch between testing modes
with the multimeter connected to a
circuit.
29. Never attempt to use the meter at a
setting combination marked as blank
on the scale.
30. Prior to testing capacitors, resistance,
diodes, or continuity; disconnect all
power to the circuit and discharge all
high-voltage capacitors.
31. Check fuse before testing current.
32. Use the proper settings, terminals,
techniques, and range for the tests
performed. Always start with the
range stated in the instructions.
33. Have the Multimeter calibrated by
a qualified technician every year. A
multimeter that is not calibrated yearly
will not yield accurate results.
Save these
instructions.
Specifications
Power
Requirements
Frequency
DC Amps
SKU 98025
9V Battery
45 to 450 Hz
Ranges: 200mA/2000mA/
20mA/ 10A
Accuracy
DC Voltage
Accuracy
AC Voltage
Accuracy
Resistance
(@0mA-200mA)
1.2%±2D; (@10A)
3%±2D
Ranges:
200mV/2000mV
20/200/1000V
(@200mV) 0.5%±1D
(@2000mV-200V) 1%±2D
(@1000V) 1%±2D
Ranges: 200/750V
(45-450 Hz)
1.2%±10D
Ranges:
200/2000/20K/
200K/2000K Ohm
Unpacking
When unpacking, check to make
sure that the item is intact and undamaged. If any parts are missing or broken,
please call Harbor Freight Tools at the
number shown on the cover of this manual
as soon as possible.
Operating Instructions
Read the entire Important
Safety Information
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
To prevent
serious injury
from accidental
operation:
ELECTRICAL SHOCK CAN
CAUSE DEATH OR INJURY.
AVOID TOUCHING EXPOSED
CONDUCTORS OF
ELECTRICITY.
Do not test voltage on AC circuits
higher than 750 volts.
Do not test voltage on DC circuits
higher than 1000 volts.
For technical questions, please call 1-800-444-3353.
Page 4
Do not test current on circuits higher
than 10 amps.
AC Voltage Measurements
1. Measure AC conductors carrying up
1. Disconnect Test Leads. Use a
to 750 VAC, 45-450 Hz.
screwdriver to remove both screws on
the rear of the unit. Observe polarity, 2. Turn the Range Selector Switch to
750 ACV setting. Always start with
and attach a 9V battery to the posts.
the highest range if the voltage is
Replace and secure the cover.
unknown.
Battery Test Selection Area
AC Volt Selection Area
DC Volt
Selection
Area
10 Amp
Selection
Area/Jack
Ohm
Selection
Area
4. Carefully touch the exposed conductors with the tips of the probes to
measure the voltage (not amperes).
5. Read measurement.
6. If the voltage is less than 200 volts,
set the Range Selector Switch to the
lower range.
Transistor
Selection 7.
Area
Transistor
/hFE Jack
ON/OFF Switch
DC Amp
Selection
Area
3. Plug the red lead into the VWmA
(Center) Jack. Plug the black lead into
the COM (Bottom) Jack. Switch the
Multimeter ON.
Volt/Ohm/
mA Jack
COM Jack
Diode Selection Area
When testing is complete, remove
Test Leads and store with multimeter.
DC Voltage Measurements
1. Measure DC conductors carrying up
to 1000 VDC.
2. Turn the Range Selector Switch to
1000 DCV setting.
2. Do not apply voltage to the Test
Leads when they are connected to
the COM (Bottom) and VWmA (Center) Jacks and the Multimeter is in an
Ohms testing setting. Damage can
occur to the multimeter or the fuse
may blow.
3. Do not switch between testing modes
with the multimeter connected to a
circuit.
3. Follow the directions above under
“AC Voltage Measurements”, only use
the DC settings instead.
DC Current Measurements
1. Measure DC conductors carrying up
to 10 amperes.
2. Turn the Range Selector Switch to the
10A position.
3. Always start with the highest range if
the amperage is unknown.
4. Plug the red lead into the 10A (Top)
Jack. Plug the black lead into the
SKU 98025
For technical questions, please call 1-800-444-3353.
Page 5
COM (Bottom) Jack. Switch the Multi- 2. Turn the Range Selector Switch to the
meter ON.
hFE position.
5. Carefully touch the exposed conductors with the tips of the probes to
measure the amperage.
3. Switch the Multimeter ON.
6. Read measurement.
5. The meter will show the approximate
hFE value.
4. Insert the transistor pins into the
appropriate hFE jack (NPN or PNP)
Note: Amperage is always tested in series
according to the EBC (Emitter, Base,
with the circuit under test.
Collector) sequence.
7. If the reading is less than .2 AMPs,
switch the red lead to the VWmA
(Center) Jack and set the Range Selector Switch to the 200 mA setting.
Diode Measurement
1. Test the voltage drop in diodes.
8. When testing is complete, remove
Test Leads and store with multimeter.
2. Turn the Range Selector Switch to the
Diode (
) position.
Resistance Measurements
1. Measure circuit resistance up to
2000K Ohms.
3. Plug the red Test Lead into the VWmA
(Center) Jack. Plug the black Test
Lead into the Com (Bottom) Jack.
Switch the Multimeter ON.
2. Warning: Never measure resistance
on a circuit with voltage running
through it.
4. Connect the red probe to the anode
of the diode and the black to the
cathode.
3. Turn the Range Selector Switch to the 5. The approximate forward voltage drop
200 W position.
of the diode will be displayed in mV.
If the connection is reversed only “1”
4. Plug the red Test Lead into the VWmA
will be shown.
(Center) Jack. Plug the black Test
Lead into the Com (Bottom) Jack.
Battery Charge Measurement
Switch the Multimeter ON.
1. Test the amount of charge left in bat5. Short the Test Leads together. The
teries.
meter should read “0” Ohms.
NOTE: This setting is for testing the
6. Touch the exposed conductors with
charge of small 9V or 1.5V batteries
the tips of the Test Leads.
only. Never use this setting to test automotive or lead-acid batteries. The
7. Read measurement.
high current could cause damage
8. If the reading is “1”, set the Range
to the meter and/or cause severe
Selector Switch to the next higher
personal injury. Use the appropriOhm (W) position.
ate DC Voltage setting to test the
open circuit voltage of such batteries
Transistor (hFE) Measurements
instead.
1. Test transistors to ensure proper
function.
SKU 98025
2. Turn the Range Selector Switch to the
Battery (
) position.
For technical questions, please call 1-800-444-3353.
Page 6
3. Plug the red Test Lead into the VWmA
ing, and any other condition that may
(Center) Jack. Plug the black Test
affect its safe operation.
Lead into the Com (Bottom) Jack.
2. After Use, clean external surfaces
Switch the Multimeter ON.
of the tool with clean cloth.
4. Connect the red probe to the positive
3. Replace battery as necessary.
terminal of the battery and the black
to the negative terminal.
4. No replaceable parts.
5. The battery amperage under a load of
370 mW will be displayed to a resolution of .1mA.
6. Normal amperage:
For a standard 9V (6LR61) battery =
25 mA
7. For a 1.5 V “AA” (LR6) battery = 4 mA
8. To prevent accidents, turn off the
tool and disconnect its power supply
after use. Clean, then store the tool
indoors out of children’s reach.UserMaintenance Instructions
Procedures not specifically
explained in this manual must
be performed only by a qualified
technician.
To prevent
serious injury
from accidental
operation:
Turn the Power Switch of the
tool to its “OFF” position and
remove the test leads before
performing any inspection,
maintenance, or cleaning
procedures.
Cleaning, Maintenance, and
Lubrication
1. BEFORE EACH USE, inspect the
general condition of the tool. Check
for loose screws, misalignment or
binding of moving parts, cracked or
broken parts, damaged electrical wir-
SKU 98025
For technical questions, please call 1-800-444-3353.
Page 7
LIMITED 90 DAY WARRANTY
Harbor Freight Tools Co. makes every effort to assure that its products meet
high quality and durability standards, and warrants to the original purchaser that this
product is free from defects in materials and workmanship for the period of 90 days
from the date of purchase. This warranty does not apply to damage due directly or
indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside
our facilities, criminal activity, improper installation, normal wear and tear, or to lack of
maintenance. We shall in no event be liable for death, injuries to persons or property,
or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. This
warranty is expressly in lieu of all other warranties, express or
implied, including the warranties of merchantability and fitness.
To take advantage of this warranty, the product or part must be returned to us
with transportation charges prepaid. Proof of purchase date and an explanation of the
complaint must accompany the merchandise. If our inspection verifies the defect, we
will either repair or replace the product at our election or we may elect to refund the
purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that
the defect resulted from causes not within the scope of our warranty, then you must
bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
SKU 98025
For technical questions, please call 1-800-444-3353.
Page 8