Sample Preparation for Volatile Compounds ( VOCs

Sample Preparation for
Volatile Compounds
(VOCs)
Sample Preparation for VOCs
Organic compounds; P ≥ 0.1 mmHg at
20°C
~ 8% of total samples
GC analyses
Petroleum, petrochemical, food, flavor and
fragrances, and environmental fields
Collection/Transport
Introduction w/o treatment
Preparation/Introduction
Measurement
Overall accuracy
Reliable result
Typical Sampling and Sample Preparation Method for
VOCs
Sample preparation
method
Principle of technique
Comments
Grab sampling
Gaseous sample is pulled
or pumped into an
evacuated metal bulb,
canister, plastic bag, or
syringe
Mostly for VOCs in air,
samples are returned to
laboratory, analytes are
isolated and
concentrated by cold
trapping techniques
Solid-phase trapping
(SPE)
Gaseous sample is passed
an adsorbent tube such as
silica gel or activated
carbon; trapped analytes
are eluted with strong
solvent
For semivolatile organic
compounds in air.
Popular sorbents include
silica gel, alumina,
porous polymer (Tenax,
PUF) and carbon
Liquid trapping
(Impinging)
Gaseous sample is
bubbled through a solution
or solvent for which the
analytes have a higher
affinity
Flow rate may cause
foaming or aerosols
Typical Sampling and Sample Preparation Method for
VOCs
Sample preparation Principle of technique
method
Comments
Headspace sampling
A solid or liquid sample is
placed in a closed glass vial
until equilibrium. Analytes
partition themselves
between a gas phase and a
solid or liquid phase; gas
phase is sampled and
injected into a GC
For determining trace
concentrations of VOCs in
samples that are difficult to
handle by conventional GC.
Increasing temperature,
salting out, adjusting pH,
would shift equilibrium of
analytes from the matrix
Purge & trap
(dynamic headspace)
A solid or liquid sample is
placed in a closed
container, VOCs are
continually purged by an
inert gas and subsequently
trapped by SPE sorbent
and then thermal desorbed
into GC (Thermal
desorption)
For determining trace
concentrations of VOCs in
samples and for analytes
that have unfavorable
partition coefficient in static
headspace sampling
Typical Sampling and Sample Preparation Method for
VOCs
Sample
preparation
method
Principle of technique
Comments
Thermal desorption
Used with purge & trap
and SPME to concentrate
VOCs; sorbent is rapidly
heated and analytes are
transferred to a GC
Typical sorbents include
Tanex TA, glass beads, and
Carbosieve, Carboxen, and
Carbotrap
Pyrolysis
Nonvolatile large molecule
samples such as polymers
and plant fibers are
thermally degraded to
cleave linkages and
produce smaller, more
volatile molecules that are
swept to GC
Degradation have defined
mechanisms and sample
may break apart in a
predictable manner
providing structural info and
fingerprint profiles about
starting compound
SPME
Already discussed
Already discussed
Tedlar Air & Gas
Sampling Bags
Impringer
Canister
Headspacce Sampling
Static Headspace (Equilibrium
Headspace)
– The sample, placed in a closed container may
be in contact and in equilibrium with the
extracting gas
Dynamic Headspace (Purge & Trap)
– The volatile compounds may be stripped off in
a continuous flow of an inert gas
¾ Ideal for dirty samples, solid materials, samples
with high boiling point analytes of no interest,
samples with high water content, and samples
that are difficult to handle by conventional GC
Static Headspace
GC
Basic of Static Headspace
Cg, Vg
Partition Coefficient (K) = Cs/Cg
Cs, Vs
Phase Ratio (β) = Vg/Vs
Cs=concentration of analyte in sample phase
Cg=concentration of analyte in gas phase
Vs=volume of sample phase
Vg=volume of gas phase
g
Co
C =
K+β
9K and β are important variables in headspace analysis.
K-Value Air-Water System (40oC)
Compound
Cyclohexane
n-Hexane
Tetrachloroethylene
Chloroform
o-Xylene
Toluene
Benzene
Dichloromethane
n-butyl acetate
Ethyl acetate
Methyl ethyl ketone
n-Butanol
Isopropanol
Ethanol
1,3-Dioxane
K Value
0.077
0.14
1.48
1.65
2.44
2.82
2.90
5.65
31.4
62.4
139.5
647
825
1355
1618
Boiling Point (oC)
81
69
121
61.1
145
111
80
40
126
77
79.6
117.7
82.4
78.3
106
Optimizing Static Headspace
Extraction
efficiency
Sensitivity
Quantitation
Reproducibility
Vial/sample
volume (β)
Temperature
Pressure
Matrix
Partition Coefficient (K)
Maximize the concentration of the volatile
components Cg in the headspace
Lower K by changing the temperature at
which the vial is equilibrated or by
changing the composition of the sample
matrix.
Cg
Cg
K
β
Headspace sensitivity
1.
2.
3.
4.
5.
EtOH
Methyl ethyl ketone
Toluene
N-hexane
Tetrachloroethylene
High K -- Temp
B. Kolb, L.S. Ettre, “Static Headspace- Gas Chromatography: Theory and
Practice,” Wiley-VCH, New York. 1997.
Headspace sensitivity
1.
2.
Cyclohexane
1,4 dioxane
β = 21.3
β= 3.46
With salt
β = 3.46
Low K -- β
B. Kolb, L.S. Ettre, “Static Headspace- Gas Chromatography: Theory and
Practice,” Wiley-VCH, New York. 1997.
Static Headspace Sampling
Gas tight syringe
Autosampler
– Balance-pressure system
– Pressure-loop system
Tekmar 7000HT Static
Headspace autosampler
Gas Tight Syringe
Step 1
Sample reaches
equilibrium
Step 2
Sample is extracted
from headspace
Step 3
Sample is injected
Gas Tight Syringe
Needle Point Style
#2
22/20-degree beveled needle point recommended for septum
penetration.
#3
90-degree needle point for use with HPLC injection valves
and for sample pipetting
#5
Conical needle with side port for penetration of septa.
Gas Tight Syringe
Advantage
– Simplicity
Disadvantage
– The loss of the substances
– No reproducibility
Autosampler - Balance Pressure
System
Sample reaches
equilibrium
Pressurization of
injection
Sample is extracted
and injected
Autosampler - Pressure-Loop System
Inlet
1
Step 3
2
Sample reaches
is extracted
equilibrium/pressurization
from
injected
headspace
Loop
To Column
Dynamic Headspace
Continuous gas extraction
Volatilized (purged) analytes can be
trapped by an adsorbent or
cryogenic trapping
For substances which are too low in
concentration or have unfavorable
partition coefficients for their
determination by static headspace
Purge and Trap
Purging gas is bubbled below
the surface of a liquid sample
using a fritted orifice to
produce finely dispersed
bubbles
The VOCs are transferred
from the aqueous phase to
the vapor phase
The gas flow sweeps the
vapor through trap containing
adsorbent materials which
retain the VOCs
The retained VOCs are
thermally desorbed and
analyzed by GC
Schematic of Purge & Trap
To GC column
Heat
Carrier gas
Purge gas
Valve
Trap Vent
HP-7675A
Purge and Trap System
Tekmar 3100 Purge and Trap
Sample Concentrator
2016/2032 Purge and Trap
Autosampler
Purge and Trap Glassware
Trapping
Adsorbent resins
– Purge & Trap
– Direct sampling
Sufficient capacity – Breakthrough
volume
– Bed volume
– Flow rate
Affinity of resin for water
Back pressure
Trap
Polymers
– Tenax
– Polystyrene
– Polyurethane foams
Carbon
– Graphitized carbon
black
– Charcoal
– Carbon sieves
Silica gel
Alumina
Tenax TA
– 2,6-diphenylene oxide
Tenax GR
– Tenax TA + 30% graphite
Carbotrap, Carbotrap
C
– Graphitized carbon blacks
Carboxen 569,
Carbosieve SIII
– Carbon molecular
sieves
Glass Beads
Tenax TA
A porous polymer resin based on
2,6-diphenylene oxide
High temperature limit of 350 oC
– Tenax degrades if react with O2 at high
temperature – abundance of phenolic
compounds and oligomers
Low affinity for water
– Useful for high moisture content
samples including the analysis of
volatile organic compounds in water
Selection of Adsorbents
Types of analytes
The physical properties of the
adsorbent
Breakthrough info.
John J. Manura,
Manura Selection and Use Of Adsorbent Resins For
Purge and Trap Thermal Desorption Applications
Scientific Instrument Services, Inc.
http://www.sisweb.com/referenc/applnote/app-32.htm
Scientific Instrument Services, Inc.
http://www.sisweb.com
Breakthrough
The breakthrough volume for a compound
on a given adsorbent and at a given
temperature is defined as the calculated
volume of carrier gas per gram of
adsorbent resin which causes the analyte
molecules to migrate from the front of the
adsorbent bed to the back of the
adsorbent bed.
(
t R × F)
=
(L/g)
VB
mA
tR = Retention time (min)
F = Flow rate (L/min)
mA = Adsorbent mass (g)
Breakthrough
Scientific Instrument Services, Inc.
Calculation of Breakthrough Volume
tR
VB
(
t R × F) − DV
=
mA
VS = VB* 0.5
VF = VB* 2
VS
VF
Breakthrough Volumes of Alcohols (C1 – C11) on Tenax
TA
0.4
5
20
120
Breakthrough Volumes of Alcohols by Tenax TA
Desorption Chart
Breakthrough Data
Hydrocarbons
Alcohols
Alkenes
Alcohols & Glycols
Acetates
Acids
Aldehydes
Ketones
Halogens
Amines
Aromatics and
Terpenes
Water
Scientific Instrument Services, Inc.
http://www.sisweb.com
Thermal Desorption (TD)
Thermally desorb analytes from the
adsorbents (P&T, direct sampling)
Direct Thermal extraction
– Volatiles from solid samples
Thermal desorption – To GC
– Transfer line
– Focusing – Improved resolution
Thermal Desorption/Extraction
0.4 mm i.d.
Glass wool
plug
Solid
sample
Adsorbent
resin
Temp. ~300
oC
10 cm
Glass wool
plug
Direct Thermal
Extraction
Temp. < 200 oC
Thermal
Desorption
Short Path Thermal Desorption
Tempearture/Time
Desorption
temperature
– Enough to
volatilize the
organic compound
without degrading
them and without
producing
unwanted
artifacts
– Temperature rate
Desorption time
– Sample matrix
– Sample size
– Interaction strength
between analyte
and the solid
surface
– Desorption
temperature
– Diffusion time of
analyte out of the
sample
Reduce Band Broadening:
Focusing
PTV
Retention Gap
Cryogenic focusing
Cryo-Trapping
Scientific Instrument Services, Inc.
Cryo-focusing
Cryo-focusing is a technique for
introducing samples from purge-andtrap concentrators into capillary GC
columns
It enables samples desorbed from
adsorbent traps to be introduced into
narrow-bore columns without losing
any resolution of the column
Single Stage Thermal Desorption
GC Detector
Sample Tube
GC Analytical Column
Two-Stage Thermal Desorption
Split
Carrier
Inlet
Cold
Trap
Hot Sample Tube
Desorb Flow Split
GC Detector
Hot
Trap
Carrier
Inlet
Carrier
Inlet
GC Analytical Column
Cryo-Trapping
Scientific Instrument Services, Inc.
Thermal Desorption
Analysis without the use of solvent
– Analysis of 100% instead of aliquot
– Elimination of solvent peak in the
chromatogram enables the analysis of
early eluted volatile analytes that are
not masked by the solvent
– Elimination of solvent reduction, no
evaporation of solvent to the
environment, and no waste
Applications
VOCs from water/soil (EPA Method 502.1,
503.1, 8030A, SW-846 Method 5030A)
VOCs from biological fluids (urine, plasma,
saliva, tissues)
Fragrances, flavors
Forensic investigation (arson accelerants)
Pyrolysis
Next stage in thermal extraction technique
Bond dissociation at very high
temperatures (600-800 oC) and break
apart into smaller and simpler volatile
molecules in a predictable manner
By measuring the fragments, the
molecular composition of the original
sample can be reconstructed
Polymer defects, variations, and
degradation mechanisms
Pyrolysis
a
H
b
H
As sample is heated, the weaker bond
breaks first forming free radicals
C
C
If C-C bonds are the weakest, the
polymer will break into oligomeric
fragments including monomers
d
H
Cl
eH
Polyethylene
Polyvinyl chloride
Polystyrene
If the side group bond is weaker,
the group is removed from the
chain before fragmented, so the
monomeric identity is lost
The materials can be heated to a relatively low temperature for
desorption of intact small molecules including solvents, excess
reagents, residual monomers, and additive such as plasticizer
Pyrolysis - Applications
Synthetic polymers (Polyvinyl
chloride, Polystyrene, Polyester)
Natural polymers
– Plant fibers (Cellulose, Cotton)
– Animal fibers (Wool, Silk)
Dried paints
Cosmetic samples