Instruction Manual PWM Driver 5A-LP2 Luci Pte. Ltd.

PWM Driver 5A-LP2
Product specifications
57
-OUT
-OUT
+OUT
+OUT
LLC- PWM5A-LP2
External signal input voltage
DC 12 V
External power input voltage
12-24V
External power input current
Max. 5A
Output voltage
Same as input voltage
Output current
Max. 5A
Output gradation
1 KHz or less
Output channels
1 channel
Unit size (mm)
136 (H) x 57 (W) x 27 (H)
Weight
170 g / unit
Operating environment
temperature
Operating environment
humidity
137
0 - 90% (no condensation)
Indoors
(LLC-PWM5A-LP2)
PWM 入力
DC5V∼12V
+
5
-
Power Input
DC12∼24V(5Amax)
+
Input / Output PWM Monitor
DC5V∼12V
LED lighting appliance dimming type
Product firmly DC12V
Flat FLEX
FLEX α
PROTERAS CO.,LTD.
Luci Division
Power supply
PWM Light controller
(LLC-PLC)
Terminal block
compatible wire
AWG16~12
1.25sq~2.0sq
DC12V dedicated
power supply
Product firmly DC24V
Power FLEX Connect
Power FLEX
Connected Light
Slim Light Indoor
Slim Light Outdoor
Line Light
MUKU bar
DC24V dedicated
power supply
Dimming type LP2
Product firmly DC24V
Line Graze Indoor
Line Graze Outdoor
Disk
DC24V dedicated
power supply
• To install the LLC-PWM5A-LP1, mount on a wall or other
surface in the orientation shown in Fig. 1 or use in a
location where dust does not accumulate on the
terminal block.
• The power equipment may occasionally cause a
humming sound. The sound becomes louder as the
load increases, so exercise caution in situations where
quiet is necessary.
• The unit generates heat. Install with a space of at least
100 mm around the unit in a non-airtight condition.
When inserting and removing cables, be sure to firmly
press the release button on the terminal block.
To ensure safe usage
The following is the safety cautions to prevent any harms or damages to others.
If the product is used against cautions, it may cause damages･electrifications･smoke.
Do not use in the following environments:
Please use DC12-24V power supply.
Do not use other power supplies such as AC100V.
Please turn off all the powers when installation and inspection.
Do not connect or disconnect the lead wires with its power on.
Always use a conforming load at no more than the maximum
number of connectable units.
Dimming type LP1
Maker
Wire stripping length
(10mm)
If the charges are in wrong direction, electric resistances will
become hot and lighting will be destroied.
7.5
電源入力
Fig. 1
0 - 40°C
PWM Dimming Driver 5A-LP2
PWM 調光ドライバー5A-LP2
( LLC- PWM 5A-LP2)
Before supplying power to this product, always check the polarities on the
DC input side.
Risk of product damage and accident if polarity is reversed, so exercise
caution.
出力PWMモニタ
Model
Usage environment
DC12~24V( 5Amax)
Tokyo Japan Regional HQ
Akasaka Bldg. 4F, 4-13-13, Akasaka, Minato-ku,
Tokyo 107-0052, Japan
Tel:+81-3-6327-7409 Fax:+81-3-6327-7410
Caution
PWM 入力
DC5V∼12V
出力PWMモニタ
PWM Dimming Driver 5A-LP2
電源入力
Φ5
27
Item / Product name
PWM 調光ドライバー5A-LP2
( LLC- PWM 5A-LP2)
■ Front view
PROTERAS CO.,LTD. Luci Division
Installation points
DC12~24V( 5Amax)
■ Side view
Instruction Manual
※unit of measure=mm
■ Top view
Luci Pte. Ltd. Singapore World HQ
883 North Bridge Road, #07-03 Southbank, Singapore, 198785
Tel:+65-6291-2410
This product is for indoor use only.
Install in a location that allows easy maintenance.
Do not do the following to the lamp fitting:
Never use the device with non-specified wire, incomplete
connections, or bent wire tips. Risk of abnormal heat generation
and fire. Use the wire indicated in the instructions, strip the
indicated length of wire, and insert all the way into the wire hole.
If the product becomes dirty, wipe with a dry cloth.
Do not use organic volatile solvents such as thinner or benzene,
and do not wash with water.
Warranty
The warranty period of this product
is one year. If a product failure
occurs during the warranty period
and the product was used in
accordance with the instructions, we
will replace the product or repair it
free of charge (this excludes on-site
repair).
- A location at high temperature (+40°C or higher)
(operating environment temperature is 0°C to +40°C).
- A location where water may splash on the product
- A location with high humidity.
- A dusty location.
- A location with corrosive or inflammable gases.
- A highly airtight location.
- A location where the product is directly exposed to salt water or organic solvents.
- A location where the product is exposed to direct sunlight.
- A location subject to the effects of electric or magnetic fields.
- A location subject to intense vibration or shock,
or a location subject to continuous vibration.
- Outdoors
- Forcibly remove the product after mounting it.
- Cut or damage the power cable. Use a damaged cable.
- Press down on the product.
- Drop the product or subject the product to intense vibration or shock.
- Spray with a cleanser or other liquid.
- Do not polish metal parts with a brush or polishing agent.
This may damage the metal and cause corrosion.
When there is abnormal situations, please cut off the power immediately,
consult with electricians, and do not touch the lighting with hands.
Inspection and maintenance
[Inspection points]
□ Do the LEDs illuminate normally? (Flickering or non-illumination?)
□ No abnormalities in the installation conditions?
□ No abnormal heat generation, noise, or odors?
[Maintenance procedure]
Gently wipe off any dirt with a soft cloth.
Do not use organic volatile solvents such as thinner or benzene, and do not wash with water.
2014/05/23
LLC-PWM5A-LP2
PWM Driver 5A-LP2
Instruction Manual
Wiring
Maximum total wiring distance of 30 m to end driver.
Input side
Normal
Output side
- PWM
-OUT
+PWM
+OUT
I nvert
Output side
Input side
出力PWMモニタ
■ Wiring drawing
AC100~200V
Input and output of PWM signals.
The signal can also be sent to the next
LLC-PWM5A.
*To expand the system,
wire in parallel branches
as shown at right.
To controller or driver
AC:N
(White)
VCTF cable 0.75sq / 2C or higher
Dedicated LED
power supply
PWM IN
PWM Dimming
Driver 5A-LP2
Luci Disk
Luci Disk
PWM OUT
Luci Disk
+
-
+
-
+OUT
-OUT
I nvert
+
Normal
When Disk is used, set to Normal
Red
Yellow
- PWM
Blk
Blue
DC / DC constant
current driver
Up to 5 can be connected
+PWM
出力PWMモニタ
PWM 入力
DC5V∼12V
PWM調光ドライバー5A-LP2
(LLC-PWM5A-LP2)
電源入力
DC12~24V(5Amax)
DC / DC constant current driver
(LDD-700HW-BK / LDD-1000HW-BK)
DC24V
To next driver
■ Disk wiring example
AC:L
(Black)
The number that can be
connected in series depends
on the maximum number
connectable in series of the
lamp fittings.
Dimming type LP2 lamp
fitting connections
AC IN
To PWM Light Controller
Dedicated LED
power supply
PWM調光ドライバー5A-LP2
(LLC-PWM5A-LP2)
AC:N
(White)
AC IN
To dedicated LED power supply
+
+
Input of DC 24 V power for LEDs.
-
AC:L
(Black)
PWM入力
DC5V∼12V
-
PWM 入力
DC5V∼12V
+
-OUT
-
+OUT
+
- PWM
-
*Use with DIP switch B on
Light Controller set to master
mode
+PWM
電源入力
DC12~24V(5Amax)
+
+
Normal
Input and output of PWM signals.
The signal can also be sent to the next
LLC-PWM5A.
DIP B
+V
I nvert
Monitor that indicates the status of PWM
output. Emits a green light at the same
dimming level as the LED appliance.
-V
+V
+
+
+
-
出力PWMモニタ
PWM調光ドライバー5A-LP2
(LLC-PWM5A-LP2)
-V
-
PWM Light Controller (rear)
→Up to 20 units can be
connected in series
VCTF cable 0.75sq / 2C
or greater
+
Outputs the PWM signal. If the receiving
side has 3 conductors (DC + -, PWM+),
use - as a common conductor.
Do not tie PWM signal line and power
line together. Risk of malfunction.
PWM signal OUT
-
Outputs DC 24 V
To dimming type LP2
PWM signal IN
電源入力
DC12~24V(5Amax)
■ How to connect the unit
White
DC12V_PWM
Maximum total wiring distance of 1 m between dedicated LED power supply and
constant current driver.
Luci Disk
Luci Disk
■ Connections
Maximum wiring distance of 30 m between constant current
driver and end LED lamp fitting