Manual Robin SmartView SIP Software version 3 or higher

Transcription

Manual
Robin SmartView
SIP
Software version 3 or higher
Version:
Date:
3.0.7 Eng
29-07-2014
gf1
Manual Robin SV ENG - v. 3.0.7
1
gf2
About this manual
This manual describes mounting, installation and programming of the Robin SmartView SIP unit in
combination with software version 3.0.3. You can update the software of the Robin SV to the latest
version. For instructions on updating see page 56 of this manual.
This manual applies to Robin Smartview SIP with part no.: C01050 - C01057, C02050 - C02057
and C02058.
If you have any questions after reading this manual, please contact us
at:
website: www.robin.nl
support website: support.robin.nl
e-mail: [email protected]
phone: + 31 72 534 64 26
Robin Telecom Development
The installed base for the Robin Compact entrance door unit exceeds 10,000 systems. The new
Robin SV is one of the first entrance door units to feature SIP protocol integration for both audio and
video in a single unit.
Consequently, this entrance door unit is not only robust and proven, the use of the ‘end-to-end’
protocol means that it also offers all the advantages of an IP environment, such as integration and
management.
We aware that the latest IP technology offers many possibilities.
As a result, we continually strive to modernise our IP products based on feedback we receive from
our customers.
The Robin SV is a logical development of the company’s first SIP door intercom , the Robin
Compact SIP.
2
gf3
Table of Contents
1 Introduction
1.1 Robin SmartView Door Intercom 5
5
2 Operation
2.1 Operating the door phone
2.1.1 Robin SV with piëzo button(s)
2.1.2 Robin SV with keypad
2.2 Answering
2.3 Controlling the camera
2.4 Controlling the built-in door opener
8
8
8
8
8
9
9
3 Installation
3.1 Package contents
3.2 Installation dimensions
3.3 Tools and materials required for mounting
3.4. Mounting instructions
3.5 Connecting the Robin SV 10
10
10
13
13
14
4 System installation
4.1 Requirements prior to installation
4.2 Connecting the Robin SV to a network
15
15
15
5 Configuration
5.1 Logging in to the Robin SV
5.2 Configuration of the Robin SV 5.2.1 Telephony
5.2.1.1 Telephony / SIP
5.2.1.2 Telephony / Phonebook
5.2.1.3 Telephony / Call settings
5.2.1.4 Telephony / Call log
5.2.1.5 Telephony / Control
5.2.2 Audio
5.2.2.1 Audio / Settings
5.2.2.2 Audio / Detection
5.2.3 Video
5.2.3.1 Video / Live
5.2.3.2 Video / H.264 5.2.3.3 Video / Settings
5.2.3.4 Video / AGC
5.2.3.5 Video / Overlay 5.2.3.6 Video / Motion
17
17
19
20
20
23
26
28
29
30
30
31
32
32
33
33
36
37
38
3
gf4
5.2.4 Network
5.2.4.1 Network / Status
5.2.4.2 Network / Settings
5.2.4.3 Network / HTTP
5.2.4.4 Network / Mail
5.2.4.5 Network / NAT
5.2.4.6 Network / RTSP
5.2.5 System
5.2.5.1 System / Device
5.2.5.2 System / Clock
5.2.5.3 System / Events
5.2.5.4 System / Security
5.2.5.5 System / Recording
5.2.5.6 System / Schedules
5.2.5.7 System / Software
5.2.5.8 System / Streams
5.2.5.9 System / Switch
5.2.5.10 System / Info
5.2.5.11 System / Debug
5.2.5.12 System / Logs
39
39
40
42
43
45
46
47
47
49
50
53
54
55
56
57
58
60
61
63
6 Support
64
Appendix A, List of key words
65
Appendix B, Electronic lock
68
4
gf5
1 Introduction
1.1 Robin SmartView Door Intercom
Integrated functions
The Robin SmartView SIP (Robin SV) is the first “end-to-end” Internet Protocol (IP) entrance door
intercom unit to offer many fully integrated functions in one single device:
Telephone device with one, two, four or six piezo push-button(s) or an integrated keypad
SIP support for audio and video
High-Definition, full-color camera with either a wide-angle or a fish-eye lens
Door opener
Advanced event mechanism
Security camera with movement- and audio detection
Remote controllable and configurable through HTTP-commands
RTSP streaming (audio and video)
Easy to install
A single module is all that has to be mounted; there are no individual loose boxes.
Simple operation
The Robin SV is equipped with one, two, four or six piezo push-buttons for dialling phone
extensions. The door opener relay is activated via the device to which the call is directed.
On the Robin SV with integrated keypad, the number of choice can be dialed directly. The ‘i’-key on
the keypad dials a programmed extension.
5
gf6
SIP communication
The Robin SV uses the Session Initiation Protocol (SIP). This means that the entrance door unit
can be connected to any business telephone exchange (PBX) or VoIP devices that supports the SIP
protocol. To check compatibility please see the compatibility chart on the supplied USB drive or on
our support website: http://support.robin.nl.
Door opener
The potential free build-in relay switch embedded in the Robin SV is activated by typing in a key
combination at the dialled device.
The phone extensions and key combination can be specified in the software application for the
Robin SV.
The relay can be used to open a door, a gate or a barrier.
Built-in camera
A real-time video image of the person using the Robin SV at the entrance door is displayed on the
screen of the phone set as soon as a call is answered, assuming the dialled phone supports video
calling.
High-Definition video quality
The build-in camera of the Robin SV is capable of displaying the video image in High-Definition
(introduced in software version 3). The image can be set to an aspect ratio of 4x3 or 16x9.
High-quality sound reproduction
The integrated concept means that there are no ‘converters’ which distort sound quality.
Consequently, the Robin SV offers exceptionally good sound quality, without echo or interference.
The audio of the Robin SV can also be configured as ‘half duplex’ , which will boost the volume
output and the microphone sensitivity.
Security camera function
The built-in security camera is a unique feature of the Robin SV. The built-in camera in the Robin
SV operates as a simple camera, allowing you to see who is at the door.
However, it can also function as a security camera. The Robin is able to deliver the video stream to
many Video Management Software systems (VMS) in two formats, MJPEG and H.264 (RTSP).
6
gf7
No separate power supply
The Robin SV is powered via ’Power-over-Ethernet‘ (PoE IEEE 802.3af).
This eliminates the need for a separate power supply; connection to a PoE network switch or
Midspan is all that is necessary.
Web-based configuration
The Robin SV can be configured on a PC or Mac via a web browser (e.g. Firefox, Chrome, Safari).
Using a web browser, modification of all the settings for the Robin SV is easy, regardless of the
physical location of the Robin SV.
In addition to configuring and programming the Robin SV via the web browser, this application also
offers the option of viewing any activity in the vicinity of the Robin SV in real time with the built-in
camera.
Because the software can be controlled with a web browser, configuration, viewing activity via the
camera, running diagnostics and testing can be performed from a remote location. You can even
access the Robin SV from the other side of the world via Internet (depending on your firewall /
router settings).
Compatible with WEBRelay
The Robin SV is compatible with an external IP relays, the WEBRelay Quad-LS. This external device
is equipped with 4 build-in relays and can be connected to the LAN.
The ‘Events’ mechanism in the Robin SV can control the 4 relays (page. 51).
7
gf8
2 Operation
2.1 Operating the door phone
2.1.1 Robin SV with piëzo button(s)
To ring the door phone, press on the bell-sign on the Robin SV.
The unit will play a ringing sound and the predefined telephone set will be called.
2.1.2 Robin SV with keypad
The Robin SV with keypad has 16 keys.
Keys 1, 2, 3, 4, 5, 6, 7, 8, 9 and 0, use these keys to call the desired extension
Green call button, call the just entered extension
Red disconnect button, disconnect the call
The ‘i’-key, call the programmed extension
The ‘C’-key, clear the chosen extension
The ‘*’- and ‘#’-key
There are two ways to use the Robin SV with keypad :
1. Enter the desired extension and press the green call button
2. Press the ‘i’-key, the Robin will dial the programmed extension (from software version 3.1)
To change the maximum amount of digits for an extension or to allow a ‘0’ to start, see
-Telephony-Call settings-General- (from software version 3.1)
2.2 Answering
Answer the Robin SV by picking up the phone that is called by the Robin SV.
In case you use a compatible videophone, the video picture of the built-in camera is displayed on
the screen of the phone.
8
gf9
2.3 Controlling the camera
When the connection between the Robin SV and the videophone is established you can control the
camera with the numeric buttons on the phone.
Use the following keys on the keypad:
2 - Moves the image up
8 - Moves the image down
4 - Moves the image to the left
6 - moves the image to the right
Keys 1 and 3 will zoom the image out and in without loss of image quality.
!Note: This option is only available if the Robin SV is equipped with a Fish Eye lens. !
2.4 Controlling the built-in door opener
The built-in door opener is controlled with predefined keys on the telephone set. When you activate
the door opener the attached door, fence or barrier will open.
You can change the default keys, a double # (##) in the interface of the Robin SV.
9
gf10
3 Installation
3.1 Package contents
The Robin SV
USB stick with the manuals and the ‘Robin Discovery Utility’ software
Anti-theft Allen key
4 anti-theft screws
4 wall plugs (6mm)
Drilling template
Tie-wrap
3.2 Installation dimensions
The installation dimensions of the Robin SV 1,2,4 and 6 buttons differ. The dimensions of the
Robin with keypad are the same as the dimensions of the Robin SV with 6 buttons.
10
gf11
11
gf12
The the dimensions of the flush-mount boxes are:

1 button - C01110
88 (B) x (47 (D) x 162 (H)

2 buttons - C01111
88 (B) x (47 (D) x 192 (H)

4 buttons - C01112
88 (B) x (47 (D) x 239 (H)

6 buttons - C01113
88 (B) x (47 (D) x 286 (H)
12
gf13
3.3 Tools and materials required for mounting
The following are required when mounting the Robin SV:
Core drill, 90 mm in diameter
Masonry drill, 6 mm in diameter
Stone chisel
General set of tools
Anti-theft Allen key (supplied)
Anti-theft screws (supplied)
6mm wall plugs (supplied)
Drilling template (supplied)
Tie wrap (supplied)
3.4. Mounting instructions
Follow the step-by-step plan described below for problem-free mounting of the Robin SV.
Step-by-step plan:
1. Drill holes of 90 mm in diameter and 60 mm in depth.
Use the drilling template supplied in the package for this.
2. Remove the cores from the drilling using the stone chisel.
Shape the hole so that the plastic housing of the Robin SV fits with room to spare.
3. Feed the cable into the hole, leave enough excess length for a loop in the hole.
4. Drill the four fixing holes for the front panel using the drilling template and insert the wall
plugs supplied with the set into the holes.
5. Connect the Ethernet cable to the clamp connector. (page 10)
6. Optional - connect the cable for operating the door switch to the clamp connector.
7. Secure the cable to the plastic housing using a tie-wrap.
8. Position the Robin SV in the hole in such a way that the looped cable fits neatly behind the
device.
9. Fix the device securely in place using the anti-theft screws supplied in the package.
13
gf14
3.5 Connecting the Robin SV
Connecting the Robin SV
To connect the Robin SV, use an Ethernet cable, type CAT5(e) or CAT6. The colours of the
individual wires match the colour codes below the connector.
To connect to the built-in relay switch, use a second cable.
Colour codes

OR / W
Orange / white

OR
Orange

GR /W
Green / white

BL
Blue

BL / W
Blue / white

GR
Green

BR / W
Brown / white

BR
Brown

REL_NO
Relays connection, ‘Normally open’

REL_CC
Relays connection, ‘Common’
14
gf15
4 System installation
4.1 Requirements prior to installation
Network connection with PoE (Power over Ethernet is used to power the door intercom; the
power supply must be 802.3af compatible).
PC with web browser.
The following web browsers are supported:
- FireFox
- Safari. Safari running under MacOS 10.8 is not supported
- Google Chrome
USB stick with the ‘Robin Discovery Utility’ software (supplied)
Network with or without DHCP support
(DHCP support is recommended)
Network cable, the cable may not be longer than 100 metres
Optional - Two-core cable for door switch operation
4.2 Connecting the Robin SV to a network
Connect the Robin SV to the network via the network connection socket on the rear.
The Robin SV will now boot. This can take up to 60 seconds.
! Note: The length of the Ethernet cable may not exceed 100 metres. This is a limit of the Ethernet
standard. !
! Note: Internet Explorer can be used for the base configuration of the Robin SV, but can’t be used
for the ‘AGC and the ‘Motion’ settings. This is because Internet Explorer doesn’t support ‘Motion
JPEG’. !
15
gf16
Windows users:
Copy the Robin Discovery Utility software to a PC that is connected to the network.
Start the Robin Discovery Utility software (double-click the icon below). Click the “Play”
button. The software will scan for Robin devices in the network. When the Robin SV is
detected, it is displayed in the list. Double-click on the Robin SV you want to configure; the
‘Web-GUI’ for the selected Robin SV will show.
Apple Macintosh users:
To detect and access the Robin SV on a Mac, you simply use the machine’s standard Internet
browser, ‘Safari’.
In the ‘bookmark overview’ of Safari (option-command-B), you will see the ‘Bonjour’ section in
the left-hand column.
Click here to display all the devices detected in your LAN network on the right-hand side of your
window, including the Robin SV. Double-click on the Robin SV you want to configure; the ‘WebGUI’ for the selected Robin SV is displayed now.
Linux users:
Enter the IP address for the Robin SV in the address bar in the web browser that is installed on
your PC in order to activate the ‘Web GUI’.
The Robin SV can now be configured further via the ‘Web GUI’
(see Chapter 4, Configuration).
16
gf17
5 Configuration
5.1 Logging in to the Robin SV
The Robin SV can be used in an ‘Administrator’ mode and a ‘User’ mode.
The Administrator can configure all the settings in the Robin SV. To initially configure the
Robin you will need to login as an Administrator.
The User can watch ‘live’ video through the camera of the Robin SV and has limited control
over the camera settings.
The login credentials can be changed in the web interface of the Robin SV. The default credentials
are:
Administrator, Login: admin, Password: 123qwe
User, Login: user, Password: <no password necessary>
We recommend changing the default passwords after initial installation and set-up.
You can log in using the Robin Discovery Utility software.
Or, if the IP address is known, you can log in without using this software via the address bar in the
web browser.
17
gf18
We assume here that the network supports DHCP (‘Dynamic Host Configuration Protocol’); if so, all
settings such as the IP addresses, netmask, gateway and DNS are automatically populated.
DHCP is a standard setting in the Robin SV. This option will suffice in 99% of all cases. However,
on occasions the network may not support DHCP. If so, the network details must be set manually.
If the Robin SV isn’t activated yet during login, you will receive a notification to activate the Robin
SV.
Follow the activation instructions or click -Skip- to continue the configuration.
18
gf19
5.2 Configuration of the Robin SV
The configuration program for the Robin SV features 5 sections; ‘Telephony’, ‘Audio’, ‘Video’,
‘Network’ and ‘System’.

‘Telephony’
In the ‘Telephony’ section, you configure all of the settings that are required for the
communication part of the Robin SV.

‘Audio’
In the ‘Audio’ section, you can make various modifications to the sound and sound
processing features of the Robin SV, such as loudspeaker volume, microphone sensitivity and
echo suppression.

‘Video’
In the ‘Video’ section, you can modify the image quality, view the live video image and set
the areas of the image to which the camera must react.

‘Network’
In the ‘Network’ section, you can view and change the network configuration settings for the
Robin SV.

‘System’
In the ‘System’ section, you can view and change the settings that influence standard
operation of the Robin SV.
This is also where you can find the ‘log files’ that make problem-solving easier.
! Note: In the Robin SV software you’ll note ’APPLY SETTINGS’ buttons. With these buttons you
confirm and activate all the changed settings. !
19
gf20
5.2.1 Telephony
5.2.1.1 Telephony / SIP
This is where you enter the data required for registering on a PBX or with a SIP Provider.
If the Robin is used for a direct connection to the telephone handset (i.e. not routed via a PBX or
SIP Provider), registration is not required.
The Robin can use a second SIP proxy / Register server for failover purposes. It will only be used
if the ‘Primary’ server isn’t registered. Reduction of the ‘Expires’ time back to 300 seconds (5
minutes), is recommended.
20
gf21
SIP registration

SIP protocol
Select the SIP protocol, UDP or TCP, UDP is default

SIP proxy / registar
Enter the IP address or hostname for the PBX or SIP
Provider

SIP proxy port number
Enter the IP port number for the PBX or SIP Provider

Use secondary SIP
proxy / Registar
* Optional - Enter the IP address or hostname for the
PBX / SIP-Provider

Username
Enter the ‘username’ for registration here

Password
Enter the ‘password’ for registration here

Register
Activates or deactivates registration

Expires
Period of time during which the SIP door intercom
can register.

Registration status
Indicates registration status
21
gf22
SIP advanced:

Outbound proxy
Select this option when a SIP proxy server is used

Outbound proxy host
Enter the IP address or hostname of the proxy server

Outbound proxy port
Enter the IP port of the proxy server

RTP port random
Switch RTP port randomly (within the specified
range)

RTP port start
Enter the lowest IP port that may be used for the
‘RTP stream’.

RTP port end
Enter the highest IP port that may be used for the
‘RTP stream’.

Use NAT
Select this option when an NAT firewall is set up
between the Robin and the SIP PBX or SIP provider.
(You can change the NAT settings in -Network-NAT-)

Keep alive
Enable keep alive packages

Enable REFER
Select this option if ‘REFER’ packages also have to
be accepted.
22
gf23
5.2.1.2 Telephony / Phonebook
Multiple telephone numbers can be entered in the phone book.
These can be used as input elsewhere, for example when setting up ‘Schedules’.
A ‘Profile’ can be associated with each ‘Phonebook entry’.
A ‘Profile’ is a set of audio and video settings. This allows definition of an individual settings profile
for each telephone number.
Phonebook:
The green ‘+’ creates a new line.
The ‘>>’ behind a line opens the details for this line.
The red X behind a line deletes the line from the list.

Description
The name that is associated with this number.

Number (see
comment)
The value entered for the telephone number (see
comment).

Profile
If required, you can select a 'Profile' for this number.

Allow register
Select this option if the Robin SV has to support a
‘Peer to Peer’ connection with a telephone set (*)
23
gf24
! Note: The number can be entered in various ways.
1. Just the number (e.g. 104, 1002, 6032 etc.). The handset is located on a connected PBX
in the same network.
2. The number, followed by the IP address of the handset that is to be dialled (e.g.
[email protected], [email protected] etc.). The handset and the Robin SV are
connected to each other directly, i.e. the call is not routed via a PBX. The Robin SV dials
the handset directly.
3. The number, followed by the IP address of a ‘Proxy server’. The handset is connected to
a PBX that uses a separate ‘Proxy server’ (e.g. [email protected], [email protected]
etc.) The Robin SV places the call to the configured PBX via this ‘Proxy server’. !
* Peer to Peer connection: If a direct connection between the Robin SV and a telephone set is
required - without the use of a SIP-PBX - please check our whitepaper: How-To_Peer-to-ENG.pdf
on the supplied USB drive or on our support website: http://support.robin.nl
Profiles:
Various parameters need to be set when creating a ‘Profile’.
24
gf25

Description
The name that is associated with this line.

Codec ulaw
Support for the G.711 ulaw audio codec.

Codec alaw
Support for the G.711 alaw audio codec.

Codec gsm
Support for the GSM audio codec.

DTMF event payload
type
Change the 'payload type' for DTMF signal
transmission. As standard, we recommend 101.

Codec h264
Support for the H.264 video codec.

Videosize
Select the resolution for video

H264 payload type
Change the 'payload type' for H.264 video codec. As
standard, we recommend 99.

Variable bitrate
Support for variable bitrate

Bitrate (kbps)
Select the maximum video bit rate. A high bit rate =
higher video quality but more bandwidth usage.

Fps
Lock the video frames per second. 0=Automatic
! Note: The selected video resolution has to be supported by the device. If the resolution is not
compatible, video distortion can occur or a black screen is displayed. !
25
gf26
5.2.1.3 Telephony / Call settings
Call priority:
The Robin SV can dial up to three numbers in a set sequence. If the first number dialled is not
answered within the set period of time*, the second number is dialled, followed by the third
number.
For the 2,4 and 6 button equipped Robin SV the call priority settings can be defined for each
individual button.

First
Select the first number to dial.

Second
Select the second number to dial.

Third
Select the third number to dial.
(*) Change the period of time in -Telephony-Call settings-General- using the ‘No answer timeout’
option.
26
gf27
Schedules:
The Robin SV features a ‘Schedule’ function. The schedules can be defined in the menu -SystemSchedules-.
This function allows you to set multiple time periods (‘Timeslots’): e.g. office hours, the lunch
break, etc.
Consequently, during the lunch break for example, the Robin SV can be set to dial a different
telephone number from that configured for normal working hours.
The ‘Timeslots’ are not prioritised so they must be set consecutively, e.g.:
8:30-12:29 morning -> call reception
12:30-13:00 lunch -> call the canteen
13:01-17:00 afternoon -> call reception
! Note: When the ‘Schedule’ function is in use and ‘Timeslots’ are created, the latter take priority
over the ‘First, Second and Third’ settings in -Telephony-Call settings-Call priority-. So the Robin
SV checks first whether a ‘Timeslot’ is active based on the current time, if not, it reverts to the
settings for ‘First, Second and Third’. !
For the 2,4 and 6 button equipped Robin SV the schedule settings can be defined for each
individual button.
Timeslots:

Schedule
Select the defined schedule

Extension
Select the number to dial
27
gf28

Auto answer
Enable auto answering of incoming calls

Auto answer delay
Answer incoming calls after X seconds

No answer timeout
End call attempt after X seconds

Max call duration
Maximum duration of a call (0 =no limit)

Max jitter delay
Maximum jitter delay

Switch led on during
calls
Activate the LED as active call indicator

Call status
Displays the status of the phone functionality of the
Robin

Phone fps
The maximum video frame rate during a conversation
(10 is recommended)
5.2.1.4 Telephony / Call log
The call log presents an overview of all the calls events to and from the Robin SV.
You can delete the complete log file using the red X alongside the ‘Delete all rows’ label.
You can delete individual log lines by clicking the red X behind the log line in question.
Call log:
28
gf29
5.2.1.5 Telephony / Control
Control allows you to manually initiate and end a call from the Robin SV.
Call:

Call:
You can initiate a call using the 'Call' button.

Hangup
You can end a call using the 'Hangup' button

Registration status
Indicates the PBX or SIP Provider registration status.

Call status
Indicates the Robin SV's call status.
29
gf30
5.2.2 Audio
5.2.2.1 Audio / Settings
You can set the speaker volume and the microphone sensitivity here.
Settings:

Speaker volume
Change the volume

Microphone sensitivity
Change the microphone sensitivity

Tone volume
Change the tone volume

Mute
Tones incoming: All incoming tones of a call (phone
-> Robin)
Tones all: All of the Robin generated tones
All audio: Mute all output (listen-in function)

Generate test tone
Play a test tone

Echo canceler
Select the echo canceler mode

Vox level (only with
‘half duplex’ setting)
Set the switch level of the microphone / speaker

Fox hyst (only with
‘half duplex’ setting)
Modify this setting to smoothen the switch between
sending and transmitting
The echo canceller can be set to:
Off, no echo cancellation
Adaptive, good echo cancellation. Allows two-way simultaneous communication
Half-duplex, makes use of sound detection to switch between speaker or microphone. This
means that you can’t have two-way simultaneous communication, but half duplex. You either
speak or listen. The advantage of this setting is that the speaker level can be raised further
than with the adaptive setting and the microphones sensitivity increases. This setting is
useful for use in noisy environments.
30
gf31
With the echo canceler set to ‘half duplex’ a ‘Vox level’ slider appears to set the switch level of the
microphone / speaker
! Note: Tuning the ‘Vox level’ is necessary to establish good communication when set to ‘halfduplex’. !
5.2.2.2 Audio / Detection
The Robin SV is capable of detecting sound.
This detection can trigger ‘Actions’ such as the staring of a recording, activation of a relay switch or
automatic calling to a phone set. These actions can be defined in the menu -System-Events-.
Depending of the location of the Robin SV and the type of sound that should trigger the detection,
two parameters can be set: the volume and the duration.
Short audio spikes can be filtered by increasing the duration setting. Background noise can be
filtered by increasing the threshold.
Audio detection:

Enabled
Enable or disable the audio detection

Treshold
Change the volume threshold of the detection

Duration
Change the audio duration of the detection
31
gf32
5.2.3 Video
5.2.3.1 Video / Live
Real-time display of the camera image. Double-click on the image to toggle between full screen
video or default size video.
Depending on the lens type of the Robin SV you can use the on-screen controls to control the
following features:
Zoom in- and out, using the ‘-’ and ‘+’ buttons
Brightness control, using the ‘moon’ and ‘sun’ buttons
Pan / Tilt the image, using the circular placed arrows
Centre the image, using the dot between the arrows
* The three buttons under the video frame functions as controls for the built-in relays switch. They
are used for:
Switching off (Close)
Switching on (Open)
Switch on and after a predefined time automatically off (Pulse)
! Note: These three buttons are only visible if the option: ’ User can control door opener’ (-SystemSecurity-) is enabled. !
32
gf33
5.2.3.2 Video / H.264
Shows near-real time video and audio of the camera. H.264 is used, this will cause a delay of
approximately 10 seconds.
5.2.3.3 Video / Settings
You can change all the camera-related settings here.
Settings: settings that are associated with the video quality.
Image - settings that are associated with the image quality.
(*) PTZ - settings that are associated with the image frame (Pan, Tilt, Zoom).
Encoder: settings that are associated with the degree of image compression.
(*) The PTZ menu will only be shown if the Robin SV is equipped with a ‘Fish eye’ lens.
33
gf34
Settings:
The ‘Sensor mode’ menu allows you to choose between two optimization profiles. You can choose
between Performance or Quality.
Performance - The Robin SV settings will be optimized to achieve the highest possible frame
rate. The video quality will loose some detailing.
Quality - The Robin SV settings will be optimized for the best video quality possible. The
frame rate will be limited to approximately 15 frames per second.
The ‘Resolution’ menu allows you to select the video image resolution. Choose between ‘VGA’, ‘SD’
or ‘HD’.
VGA - The video image will be presented with a vertical resolution of 480 pixels
SD - The video image will be presented with a vertical resolution of 576 pixels
HD - The video image will be presented with a vertical resolution of 720 pixels
The ‘Sensor aspect’ menu allows you to choose the preferred aspect ratio of the video image.
4x3 - The default aspect ratio
16x9 - Widescreen
The option ’Correction’ will only be shown if the Robin SV is equipped with a ‘Fish eye’ lens. If this
option is enabled, the ‘PTZ’ menu will be shown.
34
gf35
Image:

Brightness
Changes the brightness of the video image.

Contrast
Changes the contrast of the video image.

Saturation
Changes the colour saturation of the video image.

Auto gain control
(AGC)
'Automatic Gain Control' automatically matches video
image exposure to the light circumstances.

Fluorescent light
Activate this function if artificial light sources in a
room cause interference, e.g. TL strip lighting.

Auto white balance
(AWB)
'Auto White Balance' automatically matches the
colour temperature of the video image to the
circumstances.
PTZ:

Sharpen
Sharpening filter

Interpolation
Improve the image quality

Fisheye
Correction of the 'Fisheye' lens distortion.

Pan
Moves the image horizontally.

Tilt
Moves the image vertically.

Zoom
Allows you to zoom in/out.
35
gf36
Encoder:

Jpeg quality
Allows you to change the quality of the 'Live' video
images in the web browser (higher quality but more
bandwidth usage).
! Note: Higher quality will put extra load on the bandwidth. !
H.264 Encoder
Change the H.264 encoder quality. This will impact on the recordings made by the Robin and the
RTSP stream. The storage space and bandwidth required will increase at higher settings.
5.2.3.4 Video / AGC
Define a zone in the image where the AGC will measure.
AGC (Automatic Gain Control) automatically matches video image exposure to the light
circumstances. This option can be switched on or off at -Video-Settings-.
You use the mouse to define a selection area in the image. Draw a frame in the video image and
enlarge/reduce it by dragging the top left and bottom right corners. The red cross at the top removes
the selection frame.
Make sure that you select the most important area in your image for the AGC-function. This will
usually be the location where the people will stand when they use the Robin SV.
36
gf37
5.2.3.5 Video / Overlay
Use the overlay option to display extra information over the video image. It will be displayed in the
upper left corner of the image.
Overlay:

Enable video overlay
Enable or disable the video overlay function

Show date and time
Display the date and time

Show device name
Display the device name (change the device name in
-System-Device-)

Show device location
Display the location of the Robin SV (change the
location in -System-Device-)

Additional overlay text
Display additional text
37
gf38
5.2.3.6 Video / Motion
Motion allows you to select parts of the video image where you want to detect movement.
Detection of movement triggers ‘Actions’ such as acoustic signals, switching a built-in relay or
initiating a call to a telephone. The ‘Actions’ are set in -System-Events-.
You use the mouse to define a selection area in the image. Draw a frame in the video image and
enlarge/reduce it by dragging the top left and bottom right corners. The red cross at the top removes
the selection frame.
Consider how to minimise the chance of a false alarm when selecting the zones. For example, avoid
objects that move in the wind such as flags, branches on trees, etc.
Both detection sensitivity and the size of the object you want to detect can be adjusted. The graph
at the bottom of the image allows you to verify whether the settings are correct.
The colour of the bars is green (= no detection) or red (= detection)
The red line indicates the boundary of the detection area.
38
gf39
Motion detection:

Enabled
Activates Motion detection.

Sensitivity
Increases/reduces detection sensitivity.

Object size
Changes the size of the object to which the Robin SV
must react.
! Note: When the -Video-Motion- window for the Robin SV is open, no ‘Events’ that may have been
set can be activated, not even if Motion detection is set to ‘enabled’. !
5.2.4 Network
5.2.4.1 Network / Status
Network status indicates the current set or assigned network information.
Network status:

Interface
Shows the network interface that is used.

MAC address
Indicates the Robin SV's MAC address.

IP address
Indicates the Robin SV's IP address.

IP netmask
Shows the standard IP netmask.

Default gateway
Indicates the IP address for the standard gateway.

Primary nameserver
Indicates the IP address for the primary DNS.

Secondary nameserver
Indicates the IP address for the secondary DNS.
39
gf40
5.2.4.2 Network / Settings
Allows you to change the Robin SV’s network settings.
Configuration:

Configuration method
Select automatic (DHCP) or manual.

IP address
Enter the IP address for the Robin SV here.

Netmask
Enter the IP netmask here.

Default gateway
Enter the gateway or router address here.

Primary name server
Enter the IP address for the primary DNS (Domain
Name Server) here.

Secondary name
server
Enter the IP address for a possible secondary DNS
(Domain Name Server) here.
40
gf41
Security:

Enable 802.1x
authentication
Enable 802.1x authentication

Status
Displays the 802.1x status

Authentication type
Select the type of authentication; MD5, PEAP, TLS

Identity
Enter your identity here

Password
Enter your password here

CA certificate
Select the CA certificate (PEAP and TLS only)

Supplicant certificate
Select the Supplicant certificate (TLS only)
Settings:

IP address
Indicates the Robin SV's IP address.

IP netmask
Shows the standard IP netmask.

Default gateway
Indicates the IP address for the standard gateway.
41
gf42
5.2.4.3 Network / HTTP
Proxy:
! Note: This is the Proxy server for HTTP traffic, so not the Proxy server for the SIP connection to
the PBX !

Enable HTTP proxy
Activates the uses of an HTTP proxy server.

Proxy server address
Enter the address or hostname for the proxy server
here.

Proxy server port
The IP port used by the proxy server for
communication.
Settings:

HTTP port
Set the IP port for HTTP communication. As
standard, port 80 is used for this.

HTTPS port
Set the IP port for HTTPS communication. As
standard, port 443 is used for this.

Certificate
! Optional ! Select a certificate for the HTTPS
connection.
42
gf43
5.2.4.4 Network / Mail
Configure the mail settings for the Robin SV.
Address book:

Name
The name that is associated with this email address.

Address
Enter the e-mail address.
Mail server test:
Tests the connection with the configured mail server.

Mail server
Select the mail server you want to test here.

From
Enter a sender address for the test email message.

To
Enter a recipient address for the test email message.

Test SMTP server
Initiates the test email message.

SMTP test result
Indicates the test result.
43
gf44
Servers:

Description
The name that is associated with this mail server.

Prio
In the case of multiple servers, 'Prio' determines the
sequence in which the servers are addressed (value
between 1 and 10, 1 = high priority, 10 = low
priority)

Mail server
Name or IP address of the mail server for outgoing
messages.

Encryption
If you use a secure connection with the mail server,
the type of encryption must be selected here.

Auth
Select this option if mail server authentication is
required.

Submission
Select this option if the mail server uses the
'Submission' protocol.

Username
User name

Password
Password
44
gf45
5.2.4.5 Network / NAT
Depending on the network configuration, you may need to set NAT data in the Robin SV.
Settings:

NAT hostname
Enter the NAT address or the hostname.

NAT port
Enter the IP port for NAT.

Use STUN for NAT
address discovery
Activate this option if a STUN server is used.

Stun server
Enter the IP address or hostname for the STUN
server here.

Stun port
The IP port used by the STUN server for
communication.

Stun status
Indicates the status of the STUN server.
45
gf46
5.2.4.6 Network / RTSP
The Robin is able to stream the video and audio through RTSP.
Most video management software (VMS) solutions use the RTSP standard *.
The Robin uses H.264 for video and G.711 uLaw for audio. Not every VMS solution supports
audio.
! Note: The Robin uses the RTP over RTSP (TCP) standard. !
Settings:

Enable RTSP server
Enable RTSP support

RTSP port
Change the RTSP port (default 554)

Require authentication Use RTSP authentication

Username
RTSP username

Password
RTSP password
* For more information regarding RTSP support of the Robin in combination with VMS solutions
see the document: How-To_RTSP_ENG.pdf on the supplied USB drive. You can also download this
document on our support-site: http://support.robin.nl
46
gf47
5.2.5 System
5.2.5.1 System / Device
Info:

Product
Product type

Serial number
Serial number

Version
Software version

Revision number
Software revision number
Identity:

Device name
The name entered here is passed in the SIP protocol.
This means that the name is visible, for example when a
telephone has a caller ID display.

Location
You can enter the location of the Robin SV here, e.g. the
main entrance, loading door, barrier, etc.

Contact
Enter the details of the person responsible for managing
the Robin SV here.
Language:

Language
Select the language of the web interface
* Button:

Button sensitivity
Modify the sensitivity of the buton(s)
* Not available on all Robin devices !
47
gf48
Device activation:
The Robin SV must be activated initially by Robin Telecom Development (one-off procedure).
You start activation using the ‘Activate device’ button.
A new web page opens when activation starts. You are asked to enter a number of items of data,
after which the Robin SV is automatically activated and registered and you return to this page. You
will notice that the ‘Activate device’ button has disappeared and the current activation status is
displayed.
This activation procedure will take about 5 minutes.
! Note: The Robin SV will not be able to record video if the unit is not activated. !

Activate
Activate the Robin SV. If the Robin SV is already
activated the activation status will be displayed
48
gf49
5.2.5.2 System / Clock
You can change all the date and time settings for the Robin SV here.
Date and time:

Timezone
Select the right time zone here.

Current time
Displays the current date and time settings.

Method
Allows you to choose between manual or automatic
(NTP) time setting.

NTP server address
Enter the address or name of the time server here.

NTP status
Indicates the status of the selected time server.

Set time
Enter the date and time here (manual setting).
! Note: The Robin SV does not have a build-in backup battery. Every time the Robin SV reboots
both the date and time need to be set. By default it will use a NTP server to set the date and time.
In case of a ‘manual’ setting, this has to be done by hand after every reboot. !
49
gf50
5.2.5.3 System / Events
The Robin SV is equipped with various options for initiating actions. For example, starting an audio/
video recording, an outgoing telephone call to a predefined number, a sound signal etc.
These actions are started by an Event.
An ‘Event’ may be movement in the image, a loud noise that exceeds a predefined volume or when
a signal from one of the doors is sent to the Robin SV.
You can define the various ‘Events’ here and set the response actions that take place when an
‘Event’ occurs.
You can make actions time bound with the help of the ‘Schedule’ mechanism of the Robin SV.
That way an action can only be start within a predefined time slot. Eg. lunch or after work hours.
Define the schedules in the menu -System-Schedules-
50
gf51
Sources
Define the events. Choose from:
Call - an incoming or outgoing call
Motion - movement detection
Audio - Vox detection
Dtmf - detection of the ‘*’ & ’0-9’ key (e.g.: *1 or *7 etc.)
HTTP - enable control with http commands
Ring - during the ‘Ring’ state (incoming or outgoing)
The green ‘+’ creates a new ‘Event’ .
The ‘>>’ behind a line opens the details for this ‘Event’.
The red X behind a line deletes the ‘Event’ from the list.

Name
The name that is associated with this 'Event'.

Enable
Activates Motion detection.

Active
Indicates whether an 'Event' is active.

Type
Selects the type of 'Event'.

Min duration
Indicates how long the 'Event' remains active.

Direction
Used if the type is 'Call'. Selects incoming or
outgoing call
51
gf52
Actions:
Define the ‘Actions’. Choose from:
Recording4All - Sends video to the Recording4All Cloud Service
Call - an outgoing call
Http - send a http-command
Gpio - toggle the built-in passive relays switch
Webrelay - Use a WEBRelay external relay box *
Beep - sound signal
NVD - Specific use only
None - no action
The green ‘+’ creates a new ‘Action’ .
The ‘>>’ behind a line opens the details for this ‘Action’.
The red X behind a line deletes the ‘Action’ from the list.

Name
The name that is associated with this 'Action'.

Event
Selects the 'Event' for which this 'Action' is the
response.

Type
Selects the type of 'Action'.

Call extension (if
action = 'call')
Selects the handset that must be called by the Robin
SV.

Frequency (if action =
'beep')
Selects the frequency of the acoustic tone.

Schedule
Select a defined schedule
! Note: For more information about the Robin SV / WEBRelay, see Tech-Note: “How-To_Robin_
and_WEBRelay” PDF on the supplied USB stick or on the support website: support.robin.nl. !
52
gf53
5.2.5.4 System / Security
Authentication:

Require Authentication Un-tick the check box if you want to disable secure
access to the web interface with a login name and
password.

Admin username
Change the default Administrator login name.
(admin)

Admin password
Change the default Administrator password.
(123qwe)

User username
Change the default User login name. (user)

User password
Change the default User password. (no password)

User can control door
opener
Displays three buttons below the Live video frame
(-Video-Live-) to control the built-in relay switch
! Note: As soon as you activate the ‘Require Authentication’ check box, enter a user name and
password and click the ‘Apply settings’ button, the web interface will demand a log-in name and
password !
53
gf54
Certificates:

Common name
This is the name of the certificate.

Certificate
Upload a certificate from the PC to the Robin SV.

Certificate info
Detailed information about the certificate.
5.2.5.5 System / Recording
54
gf55
5.2.5.6 System / Schedules
The Robin SV has multiple functions that can be made time-bound. Use this schedule menu to
create timeslots. They can occur at a specific day, in the weekend, on week days or on all days.

Description
Descriptive name of the Schedule

Day
Select the day / days for this schedule

From
Start time

To
End time
55
gf56
5.2.5.7 System / Software
New software versions for the Robin SV are released regularly. These versions include improvements
and occasionally also introduce new functions.
Updating is a two-stage process; the first step is to check whether new software is available. If so,
you can initiate the upgrade to the latest version.
After the upgrade, the Robin SV has to be rebooted.
Backup:

Backup configuration
You can make a backup of the settings using the
'Download' button. A file called 'Backupsettings.txt' is
downloaded to the PC.
You can restore a backup to the Robin SV using the
'Upload' button. First, you select a backup file that
was created earlier. After restoring the backup, the
Robin SV must be rebooted.
Tools:

Restart Robin
application
Starts the Robin software up again. This is faster
than rebooting the device.

Reboot device
Reboots the complete device. It may take 30 seconds
before the Robin SV is active again.

Restore application
defaults
Restores the default settings for the Robin SV.
56
gf57
Updates:

Check for new
software versions
Checks whether new software is available.

Currently running
version
Indicates the current software version.

Currently installed
version
Indicates the software version that has already been
installed.

Upgrade to latest
version
Downloads the latest version of the software and
installs it on the Robin SV.
! Note: Internet access for the Robin SV is necessary to update the software of the Robin. !
5.2.5.8 System / Streams
The ‘Streams’ menu shows all active video streams.
57
gf58
5.2.5.9 System / Switch
The Robin SV has a built-in voltage-free relay contact. This can be used to open a door or a barrier.
When a connection has been established between the Robin SV and a telephone handset, the relay
can be operated via key combinations.
For examples on how to connect the Robin to an electronic door lock, see:: ‘Appendix B, Electronic
lock’.
Control:

State
Displays the status of the relay switch (open / close)

Close
Deactivate the switch

Open
Activate the switch

Pulse
Activate the switch and after a predefined time
deactivate the switch automatically
58
gf59
! Note: For the actions below, the user can enter his/her choice of telephone key combinations
(0...9, * and #). !

To open
The door contact opens and closes again after a set
time (Pulse time). The default key combination for
this is ' ##'.

To keep open
The door contact stays open, independently of the set
time.

To close
The door contact closes.

Pulse time
You can set the time that the door contact stays open
here. (Time period of a minimum of 1 second and
maximum of 30 seconds.)

Play sound
Generates a tone when the door contact is active.

Hangup after opening
Breaks the connection after activating the door
contact.

Close door after
hanging up
Close the door contact after the phone is
disconnected

Label for ‘pulse’ action Change the display name for ‘Pulse’

Label for ‘on’ action
Change the display name for ‘On’

Label for ‘off’ action
Change the display name for ‘Off’
! Note: The labels ‘Pulse’, ‘On’ en ‘Off’ will be visible under the live video image (-Video-Live-).
The option ‘User can control door opener’ needs to be enabled (-System-Security-). !
59
gf60
5.2.5.10 System / Info
Info displays detailed information about the Robin SV.
Advanced:

Product
Product type

Device
Device ID

Serial number
Serial number

Version
Software version

Revision number
Software revision number

Uptime
Time that the Robin SV is switched on.

Load average
Average processor load (UNIX style).

Temperature
Temperature in the Robin SV.

CPU speed
Current processor speed.

System clock time
System time.

Runs
Displays the amount of runs
60
gf61
5.2.5.11 System / Debug
The Robin SV features a built-in ‘Debug’ function. This allows you to create a ‘Network trace’ of
all the network traffic to and from the Robin SV. This tool allows fast and effective resolution of
problems with the Robin SV.
The ‘Go to Robin’ function enables remote support to the unit. It connects the unit to Robin
Telecom Development and can be used for remote support.
! Note: Go to Robin will only work after contacting the support department of Robin Telecom
Development. !
61
gf62
Trace:

Status
Indicates the status of the 'Trace'.

Interface name
The interface for which the 'Trace' is created.

Default sniffer
duration
Sets the standard 'Trace' duration time. It stops
automatically after the time has elapsed.

PCAP filter line
The 'Trace' is filtered as standard to ensure that only
the important network data is stored.

Mail result
Send the 'Trace' automatically as an email message.

Mail server
Select the mail server that is to be used to send the
email.

From-address
Select the email address from which the email
message will be sent.

To-address
Select the email address to which the email message
will be sent.

Comment
Add a standard text block to the 'Trace' email
message.

Starting
Starts creating the 'Trace'.

Stop
Stops 'Trace' creation.
Go to Robin:

Connect
Connect to ‘Go to Robin’

Status
Display the connection status of ‘Go to Robin’

Message
Information regarding the ‘Go to Robin’ connection
62
gf63
5.2.5.12 System / Logs
The Robin SV registers all events that occur. These are logged in a log file.
Log settings:

Max lines to keep in
log
The number of log file lines that are stored.

Download
Download the log file to the PC.
Application log:

Timestamp
Time stamp for the log entry.

Log level
The log entry classification.

Class
The software component in the Robin SV that led to
generation of the entry.

Message
The actual log message.
63
gf64
6 Support
For details of special settings, requests for support and FAQs, please use our ‘online’ support page:
http://support.robin.nl
64
gf65
Appendix A, List of key words
Default setting:
Standard programme setting.
DHCP:
‘Dynamic Host Configuration Protocol’.
Computer protocol that describes how a computer can obtain its network settings from a DHCP
server.
DNS:
‘Dynamic Name System’.
Protocol for managing domain names and IP addresses on the Internet.
DNS server:
This is the system that compares all the domain names and IP addresses in a database with each
other and links them with the aid of a DNS server.
End-to-end:
The ‘end-to-end’ principle is one of the core principles of the Internet and is reflected in the design
of the underlying methods and protocols of the ‘Internet Protocol Suite.’
The principle is based on definition of the communication protocol actions in such a way that they
take place at the ‘end points’ of a communication system, or as close as possible to the source that
is to be verified.
Gateway:
A ‘gateway’ is a network point that acts as a “door” to a network other than the local network.
GUI:
‘Graphical User Interface’.
The graphical user environment is a tool for interacting with a computer that uses graphical images
and text.
HTTP:
‘Hypertext Transfer Protocol’.
http is the protocol for communication between a web client (generally a web browser) and a web
server. This protocol is not just commonly used on the World Wide Web, it is also used in local
networks (which we call an intranet).
IP:
‘Internet Protocol’.
This is the part of the system that is used to allow computer networks to communicate with each
other via other networks, such as the Internet.
65
gf66
LAN:
‘Local area network’.
Local area network of two or more computers that are connected with each other, either directly or
via a shared medium.
MAC (address):
‘Media Access Control’.
The MAC address is a unique identification number that is allocated to a device in an ethernet
network.
Hardware address is another name for the MAC address. It ensure that the devices in an ethernet
network can communicate with each other.
Midspan (PoE):
A Midspan (PoE) is a device that injects power over a standard ethernet connection.
NAT:
‘Network Address Translation’.
Network Address Translation, for which the terms Network masquerading or IP-masquerading
are also used, is the translation of IP addresses and often also TCP/UDP port numbers from one
separated range to another. Often used to allow multiple users of a home network to access internet
via a single IP address.
Netmask:
Binary number that is used to create a subnet.
NTP:
‘Network Time Protocol’.
A protocol that is used by the time server.
PBX/PABX:
‘Private (Automatic) Branch Exchange’.
Abbreviation used for a business telephone exchange for private use.
PoE:
Power over Ethernet.
A system for delivering power and data via an Ethernet network.
PRACK:
‘Provisional Acknowledgement’ – preliminary confirmation.
One of two types of confirmation within the SIP ‘request-response’ protocol.
‘Final Acknowledgement’ is the other type of confirmation.
Proxy server:
A proxy server is one that is located between a user’s computer and the computer where the
information the user wants is stored.
66
gf67
PTZ:
PTZ stands for Pan / Tilt / Zoom. Pan is the left/right movement. Tilt is the up/down movement.
Zoom is used to zoom in and out.
Robin-ID:
A Robin-ID is a combination of a name and password that is created during the Activation of a
Robin device. The Robin-ID can be administrative purposes at Robin Telecom Development.
SIP:
‘Session Initiation Protocol’.
A protocol that makes multimedia communication (audio, video and other data communication)
possible and used among other things for the Voice over Internet Protocol (VoIP).
STUN:
‘Session Traversal Utilities for NAT’.
‘STUN’ is a protocol or tool that is used when applying NAT.
Time server:
A ‘time server’ is a network computer, which reads the time from a clock that has been allocated to
it and transfers this information to other computers that use the same network.
VLAN:
Virtual Local Area Network.
Self-explanatory (see also LAN).
VoIP:
‘Voice over Internet Protocol’.
A protocol that uses the Internet or another IP network to transport
speech.
Web GUI:
A web browser-supported graphical user environment (see also GUI).
67
gf68
Appendix B, Electronic lock
The Robin has a built-in voltage-free relay contact. The Robin is not able to power a electronic lock,
a power supply is required.
There are many different electronic locks on the market. We advise to use the prescribed method of
the electronic lock manufacturer to connect the Robin.
This Appendix shows two common ways to connect the Robin to the electronic door lock. That
doesn’t mean that these two options are the only options possible!
Basic electronic door lock with power supply:
Electronic door lock with input contact on the control box:
! Note: The relay switch of the Robin doesn’t supply power for the electronic lock! Make sure that
the switched voltage does not exceed 48V and the switched power is max. 60W. !
68

Manual Robin SmartView SIP Software version 3 or higher

Transcription

Similar documents

FCE Sample Test February 2009

Homeward Bound

Robin Hood`s Bay

Conestogo Mercantile

vote for the world`s greatest bank job.

Print Format - La Pendulerie

2016 Keynote speaker: Robin Sigars

OALCF Task Cover Sheet Task Title: Learner Name:

Robin Hill Serviceberry*

R Did you know? OUND ROBIN