T3-CV Receiver Manual Safety & Warnings

T3-CV Receiver Manual
1-800-387-4081
Before you begin, read all warnings and installation instructions.
Safety & Warnings
Securely mount the T3-CV using the two mounting points at each end.
This product is intended to be installed and serviced by a qualied licensed electrician. Install in accordance with
the National Electric Code, and local regulations.
Only power with a regulated (listed) constant voltage Class 2 power supply (12-24V DC).
Ensure applicable wire is installed between driver, xture, and any controls in between. When choosing wire,
factor in voltage drop, amperage rating and type (in-wall rated, wet location rated, etc.). Inadequate wire
installation could overheat wires and cause re.
This product is rated for indoor installation and only for dry locations. Do not install in washrooms or areas near
water (or the possibility of in the future).
Do not modify this product beyond the instructions in this guide or the warranty will be voided.
Wiring diagrams in this installation guide for basic installations. Please carefully review your installation before
proceeding with a qualied electrician familiar with low voltage wiring techniques.
Warning: Input voltage must be identical to output voltage of the LED Fixture!
WIRE 6-8MM (0.25-0.30”)
Exposed wire should not be more than 6- 8 mm long & solder tip (tinned). Do not allow Wires to
cross and insure all exposed wire is fully inserted into the screw terminals. Hand tighten screw
terminals. Use 22 to 16 AWG gauge wire for output terminals.
T3-CV Operation Overview
Remote ID
Learning Button
MODEL : T3-CV
2.4G WIRELESS REMOTE CONTROL
POWER INPUT : DC5V-DC24V
OUTPUT : 6A x 3CH
Mounting point
RGB LED Connection Socket
Power Input
DC12V~24V
Diagram-1
T3-CV Hard Wire Diagram (uses XLD series power supply)
L
N
G
O utp u t
AC Power
50/60Hz
L
N
In p u t
Class 2 Low Voltage Regulated Driver
XLD series Power Supply
MODEL : T3-CV
2.4G WIRELESS REMOTE CONTROL
POWER INPUT : DC5V-DC24V
OUTPUT : 6A x 3CH
[+]
[B]
V+
[G]
[R]
V-
T3-CV
RGB LED Strip
Diagram-2
LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA
Copyright @2014 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
T3-CV Receiver Manual
1-800-387-4081
T3-CV - 12V Wire Diagram (uses MTR72DAUL-1250B power supply)
Class 2 Low Voltage Regulated Driver
MTR72DAUL-1250B Power Supply
AC Power
50/60Hz
MODEL : T3-CV
2.4G WIRELESS REMOTE CONTROL
POWER INPUT : DC5V-DC24V
OUTPUT : 6A x 3CH
[+]
[B]
[G]
[R]
MTR72DAUL-1250B
T3-CV
H05 Connector cable
If used with MTR72DAUL-1250B
Power Supply
RGB LED Strip
Diagram-3
T3-CV Technical Specications
Input voltage
DC5V-DC24V
Max current load
6A×3CH Max Class 2 (5A)
Max output power
75W/180W (12V/24V)
Compatible remote control
T1/T2/T2M/T3/T3M/T3X
Remote Distance
25m
Working temperature
-20°C~40°C
Dimension
L175 × W44 × H30mm
Package size
L178 × W48 × H33mm
Weight (G.W.)
110g
1
LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA
Copyright @2014 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).