GENERATOR & POWER STATION PROTECTION

A 2-Day Professional Development Seminar on
GENERATOR & POWER STATION
PROTECTION
SYDNEY
17-18 November 2014
Mercure Sydney
Who Should Attend
Technical personnel who are involved in planning,
design, installation, operation and maintenance
of protection system for generators and
power stations, such as
PERTH
27-28 November 2014
Mercure Perth
Protection Design Engineers
◊ Planning Engineers
◊ Operation & Maintenance Engineers
◊ Circuitry Design Engineers
Commissioning & Project Management Engineers
◊ Technicians
◊
◊
9.00 am - 5.00pm
Organised By :
CPD INTERNATIONAL PTY LTD
Your True Partner in Attaining Professional Excellence
Introduction
The requirements of safety, minimisation of damage to faulted plant, minimisation of consequential damage to healthy
plant and maintenance of a stable and secure supply of electricity are paramount to all protection designs.
A
generator may be exposed to three types of occurrence
which require protection schemes to operate effectively and
efficiently but in vastly different time frames.
◊ Generator Fault : This requires instantaneous tripping of
the generator to minimise the damage caused.
Generator multiphase fault levels may exceed 100kA,
whereas, via high resistance earthing techniques, the
same generator may have an earth fault level of only a
few amperes.
◊ Generator Event : This is an event local to the generator
which will not immediately cause damage but will
eventually do so unless rectified. Protection initiates an
alarm rapidly to alert the operator and to allow
intervention and, if this is unsuccessful, finally tripping
before actual generator damage occurs.
Course Content
1. High Impedance Differential Protection
- Application to Generators, Transformers and
Busbars
●
●
Determination of setting voltage
● Determination of scheme primary operating current
●
In this seminar we will consider the application of protection
to generators, considering the three occurrences mentioned
above. This will facilitate an appreciation of generator
protection, the coordination aspects of these protection
schemes, and the information required to determine
protection settings.
Application
of
series
●
●
shunt
MOVs)
CT supervision requirements
Application of high impedance differential protection
principles to plant other than busbars
●
Introduction to Buchholz and Pressure Relief
Devices (PRDs)
● Introduction to
Positive,
Negative
and
Zero
Sequence Component Analysis, in particular:
● Transformer Earth faults, sequence components
and transformer phase shifts
● Transformer Phase-Phase faults, sequence
components and transformer phase shifts
●
Biased differential protection
● Inrush and magnetising currents
●
Over-excitation (excessive V/Hz) currents
● CT connections for phase correction
●
CT connections for zero
compensation
●
CT ratio selection
●
Phase angle, zero sequence and CT ratio
compensation via microprocessor based relay
Thus the task, not only for the protection engineer, but for all
engineers and technicians associated with the power station,
is to ensure that planning, design, coordination,
implementation, commissioning, operation and maintenance
of protection systems optimises both the dependability and
security of these schemes.
applications
● Restricted
Earth
What You Will Learn?
●
Delegates will learn the principles of power station protection
schemes, the art of scheme selection, and the generic
processes associated with determination of optimal settings
and configurations for the protection relays and schemes
associated with power station generators, motors, busbars
and transformers.
and
2. Transformer Protection
But, beyond the generator itself, the power station engineers
and technicians need an intimate understanding of the
protection schemes associated with the remaining plant,
including busbars, transformers and the many large induction
motors.
This 2-day seminar focuses on the principles of generator
and power station protection schemes, including their
application to generator faults, generator events, external
power system events, and power station motor, busbar and
transformer faults.
(stabilising)
(de-sensitising) resistors
● Application of non-linear resistors (Metrosils and
◊ External Event : This is a transmission system event
which will not immediately cause damage to the
generator and can be rectified by operator intervention.
An alarm is generated rapidly to alert the operator of the
condition, followed by tripping as necessary if appropriate
action is not taken or is not successful. In particular, note
that such events affect every generator within a particular
power station, and even may affect generators over a
wide area. Hence tripping must be delayed as long as
possible to avoid widespread system shut-downs, but
must nevertheless still provide protection for the affected
generating plant.
High impedance differential protection principles
Fault
sequence
(REF)
current
protection
of
transformers
Transformer delta connected windings and the
application of earthing transformers
●
Earthing Transformer OC & EF protection
● Effect on the overall transformer differential
protection scheme
● Zero sequence current consequences and
compensation techniques
About the Course Leader
Barrie Moor B.E (Elec),RPEQ
3. Motor Protection
●
Starting Current, Stalling Current, High Inertia Loads
and Thermal Capability
●
Number of Starts Limitation
●
Effects of Unbalanced (Negative Phase Sequence)
Events
●
Earth Fault Protection – High impedance and core
balance schemes
●
●
RTD Protection
Undervoltage Protection
●
Loss of Load Protection
●
Over Current Protection – via CBs, fuses and fuse
contactors
●
Differential Protection
4. Generator Protection
●
Biased Differential and High Impedance Differential
●
Protection Schemes
Voltage Displacement Protection
●
Stator Earth Fault Protection (100%, 95%, REF and
3rd harmonic schemes)
● Stator Interturn Protection
●
Rotor Earth Fault Protection
● GCB Fail Protection
●
Stator Overload Protection
● Negative Phase Sequence (NPS) Protection
●
Over Voltage and Over Excitation Protection
●
Under Excitation Protection
● Reverse Power Protection
●
●
Under and Over Frequency Protection
Out of Step Protection
●
Embedded Generator Islanding Protection
CPD Recognition
This training program is designed to meet the Continuing
Professional Development (CPD) needs of participants.
A
Certificate of Attendance will be awarded at the end of the program.
This serves as evidence of your personal and professional
commitment to building your career.
Barrie Moor is the Principal
Engineer
at
Power
System
Protection Training, a provider of
professional development training
seminars on the topics of power
system principles and power
system protection. With over 39
years experience in the Queensland electricity transmission industry, Barrie Moor has been involved in the
design, coordination and implementation of protection
schemes associated with Queensland’s HV and EHV
transmission systems since 1981. Barrie also has
extensive experience with the protection of large
generating plants.
From 2000 to 2007, Barrie filled the role of Senior
Engineer Protection Design, with statewide responsibility,
leading Powerlink’s Protection Design Team. From 2007 to
2012, in the role of Principal Consultant Substation
Protection, and then Principal Engineer-Investigations.,
Barrie provided specialist Protection Design and Fault
Analysis services to support the Asset Management and
Operational Groups within Powerlink.
Barrie has 20 years experience within Australia and
Internationally
in
the
provision
of
university
post graduate training on the design and implementation
of HV and EHV Transmission Protection Systems. He has
presented a number of papers on specialized aspects of
protection design at conferences both within Australia and
internationally. Barrie has also represented Powerlink on
CIGRE committee APB5, Power System Protection and
Automation and has served as a corresponding member of
Cigre and IEE working groups on Protection Systems.
Who Should Attend?
This seminar will assist both those whose day to day work
involves them in the application of protection design,
coordination and relay setting, and also to those in less
directly associated areas of generator and power station
protection system design.
This seminar has been
prepared specifically to meet the requirements of:
Protection Design Engineers, to identify protection implications and to ensure design, coordination
and relay setting principles provide the necessary
levels of speed, security, dependability and safety
Planning Engineers, to identify the difficulties in
providing protection for various power system configurations under review
Maintenance Engineers, to ensure that system
protection is not compromised as primary and/or
secondary system plant is removed from service
during maintenance
Circuitry Design Engineers, to ensure that protective schemes are implemented in a manner to
provide optimum performance
Commissioning and Project Management
Customised In-House Course Available
This program can be customised to suit the specific needs of your
organisation at significant savings details. Please contact us on
(02) 8448 2078 or email: [email protected] for more details.
Engineers, to ensure the actual field installation of
the protection scheme and associated relay settings
meets the design requirements
Technicians, to understand the importance of their
role in installing, testing and maintaining effective,
reliable, dependable and secure protection systems
HOW TO REGISTER?
Step 1 - COMPLETE THIS FORM AND FAX TO : (02) 8068 0130
A Confirmation of Booking and a Tax Invoice will be sent to you
(via email or fax) upon receipt of registration form.
Step 2 - MAKE APPROPRIATE PAYMENT, AFTER RECEIPT OF INVOICE,
BY :
OR CREDIT CARD :
□VISA
□MASTER
Name on Card : __________________________________________________
Card No.
: __________________________________________________
Expiry Date
: __________________________________________________
Signature
: __________________________________________________
(please tick √ the relevant box to indicate your method of payment)
□
CHEQUE attached - payable to CPD International Pty Ltd. Mail it
together with the completed registration form to us.
OR
□
EFT (Electronic Funds Transfer) to
Account Name
BSB No
Account No
Bank
Reference
:
:
:
:
:
CPD International Pty Ltd
182-222
1210 77176
Macquarie Bank
Please quote our invoice no.
Purchase Order No. : _________________________________ (if applicable)
ENQUIRIES :
VISIT
:
CALL (02) 8448 2078 or EMAIL [email protected]
www.cpdint.com.au
for more courses
REGISTRATION FORM
Please register the following delegates for the event -
“Generator and Power Station Protection” Seminar
(Please tick √ the relevant box to indicate your choice of dates and venue, and print clearly in black pen for proper fax transmission)
□SYDNEY, 17-18 November 2014, Mercure Sydney
□PERTH, 27-28 November 2014, Mercure Perth
DELEGATES :
1) MR/MS : …………………….……………….…………………..…………….…...………………...... JOB TITLE : ……..……………..…………...…………………..…….………..
EMAIL : ……………………………….…………………………..……...…….....……. ……………….…. TEL : ………………….……………………………….………….....................
2) MR/MS : ……………………………..…………….……………………………..............................… JOB TITLE : …………………..……………...….……………………….……..
EMAIL : ……………………………………………..…………………….…………………….....………… TEL : ……………….…………….....………………...……….…………..…...
3) MR/MS : …………………………………………………….…………………...……………………..… JOB TITLE : ………………..….……………………..……….………………..
EMAIL : ……………………………………………………………………….….............….…………….....TEL : ……………………...…………….…………………………….…...…...
ORGANISATION NAME : ……………………...……………………………………………….………………………………………...……………..………………………...……….....…
ADDRESS : …………………………………………..………….……………………...….. ……………… STATE : …………………..…….… POSTAL CODE... .……………..….….
CONTACT PERSON : MR/MS ……………………………….………………………………………........JOB TITLE : ……..…………………….....…….…..……………….………….
SECTION/DEPARTMENT : ………………………………………………………………….……………...TEL : …………………………………...………..……..……...…….…..……..
EMAIL : ………………………………………………………………………………………………….…..…FAX : ………………………………….….…………………………….………
COURSE FEES & DETAILS
Course Registration Fee :
Register before 10 October 2014 :
AUD1,280.00 + AUD128.00(GST) = AUD1,408.00 per delegate.
Register after 10 October 2014 :
AUD1,380.00 + AUD138.00(GST) = AUD1,518.00 per delegate.
Register 3 or more delegates at the same time for this course:
AUD1,242.00 + AUD124.20 (GST) = AUD1,366.20 per delegate
Payment Terms :
Payment is required before the event.
Delegates may be refused admission if payment is not received prior to
the event. Registration Fee includes lunch, refreshments and training
documentation/notes.
Cancellation : A substitute or replacement is welcome at no additional charge. However, any cancellation of registration must be made in
writing. If you cancel at 14 or more calendar days before the commencement of the event, you will receive a full refund, minus a nonrefundable $250 administration fee. If you have not paid for the event,
you will still be invoiced for the $250 administration fee. If you cancel
within 14 calendar days of the commencement of the event, you will be
charged the full fee, even if you have not paid yet.
Accommodation :
Arrangements for accommodation are the
responsibility of participants and costs are not included in the course
fee. Accommodation is available at the venue/close by and information
can be made available to interested participants.
Note : The organizer reserves the right to make changes to the event
schedule, contents and venue. The views expressed in the event are
not necessarily those of CPD International Pty Ltd.
———————————————–—-——-—————–——————————-—
ABN 49 108 072 162
ACN 108 072 162
Address : Level 20, Tower A, Zenith Centre
821 Pacific Highway
Chatswood NSW 2067, Australia
Tel : (02) 8448 2078 Fax: (02 ) 8068 0130
Your True Partner in Attaining
Professional Excellence