Dell Wyse Client VESA Mounting Bracket for Dell P Series Monitor

Dell Wyse Client VESA Mounting
Bracket for Dell P Series Monitor
Installation Instructions
This VESA mounting bracket (P bracket) is used for mounting a Wyse client to the Dell P
Series Monitor or the Dell E24 Monitor. A #1 Phillips-head screwdriver is required.
NOTE: The mounting bracket can be used with the monitor in either landscape or
portrait orientation. Before you install the client, first determine your preferred display
orientation.
Wyse Clients Using this Bracket
Wyse clients, Dx0D, Dx0Q, N03D, PxN, Tx0, and Tx0D, may use the Dell Wyse Client
VESA Mounting Bracket (P bracket) for Dell P Series and E2414 Monitors.
Table 1
Wyse Clients by Regulatory Model Number and Product Name
Dx0D
Dx0Q
N03D
PxN
Tx0
Tx0D
5000-D00DX
(Xenith Pro 2)
5400-D00Q
3290
5020-P25
3000-T00X
(Xenith 2)
3002-T00DX
(Xenith 3)
5200-D00D
5490-D90Q7
3010-T10
3012-T10D
5212-D10D
5490-D90Q7P
3050-T50
5212-D10DP
5490-D90Q8
5250-D50D
5290-D90D7
5290-D90D7P
5290-D90D8
2
Shown below are Dx0D and Tx0 on monitors operating in portrait and landscape
orientations.
CAUTION: Mount the client only as shown. Improper placement (where the back
panel or front panel is facing down, or where the vents are facing in towards the
monitor) could restrict the airflow of heat from the device and damage it. For portrait
orientation, ensure that the client power button always faces right.
CAUTION: Do not enclose the client in a confined environment without proper
ventilation.
Included in the Kit (PN 920397-01L)
Parts provided in the kit include: (1) P bracket, (1) power adaptor holder, (1) stopper, (1)
M2.5 screw, (4) M4 screws and (4) hex nuts.
NOTE for N03D: You need to purchase separately the client horizontal stand/VESA
bracket with the ‘hex’ holes. For N03D, use PN 920372-01L.
NOTE for PxN, Tx0, and Tx0D: You need to purchase separately (or have received
with your client) the client horizontal stand/VESA bracket with the ‘hex’ holes.
For Tx0, use PN 920334-01L. For PxN and Tx0D, use PN 920334-11L.
3
What Goes Where on the P Bracket
Mounting Dx0D and Dx0Q Clients
Use the following instructions to mount the Dx0D and Dx0Q client to the P bracket.
1. Preparing the Client - Remove the client from its existing stand. If not already
removed, use a Phillips-head screwdriver to remove the four (4) filler screws from
the side of the client and discard them.
2. Attaching the Client - Select your preferred display orientation, see note below.
Install the client on the P bracket (the side with the release button). The client shown
below has been installed for landscape orientation. Use the provided four (4) M4
screws to attach it to the bracket. For Dx0D and Dx0Q, use the VESA hole set
starting with the outer edge screws holes.
NOTE: When installing for a monitor in landscape orientation, the client power
button should be facing to the right. When installing for a monitor in portrait
orientation, the power button should be facing down (after rotation, the power
button will be facing to the right).
4
3. Attaching the Power Adaptor Holder - Install the power adaptor holder on the
P bracket (the side with the release button). Slide the small hooks downward into the
vertical slotted holes and the large hooks onto the top edge of the bracket. Use the
M2.5 screw provided to secure the ‘holder’ on the bracket where indicated.
4. Attaching P Bracket to the Monitor - Place the monitor on a padded surface with
the display facing down. Remove the stand from the monitor by pushing the
monitor’s quick release button. Remove the four (4) VESA screws from the back of
the monitor and set them aside. Position the P bracket's central section on the back
of the monitor. Slide the bracket’s top tabs into the dedicated tab slots, and then
firmly push down bottom edge of bracket until it snaps in place. For additional
security, reinstall the monitor VESA screws that you had set aside (do not
over-tighten).
CAUTION: If you need to remove the P bracket, remove monitor screws and
then press the lower quick release button on the monitor, not the upper release
button on the bracket.
5
5. Reinstalling the Monitor Stand - Insert the upper stand tabs into the dedicated
space on the P bracket and press down until the quick release button latches in.
Place the monitor in the upright standing position.
6. Adjusting and Securing Monitor Height
For landscape orientation - Adjust the monitor height and attach stopper. Make
sure that the stopper tab is facing up on the front side of the stand, and then snap
the stopper ends together.
For portrait orientation - Raise the monitor to ‘maximum’ height and attach
stopper. Make sure that the stopper tab is facing up on the front side of the stand,
and then snap the stopper ends together. Rotate the monitor.
NOTE: The purpose of the stopper is to support the extra weight of the client
and bracket.
NOTE: If mounting the P bracket on the E2414 Monitor, the stopper does not
need to be used.
7. Finishing - Make all desired connections, and then connect the power adapter’s AC
power cable to an electrical outlet.
CAUTION: Do not enclose the client in a confined environment without proper
ventilation.
6
Mounting N03D, PxN, Tx0, and Tx0D Clients
Use the following instructions to mount the N03D, PxN, Tx0 and Tx0D client to the
P bracket.
1. Preparing the Client and VESA Bracket - Remove the client from its plastic
horizontal stand/VESA bracket. On the ‘inside’ of the plastic bracket, slip one of the
four (4) provided nuts into a screw hex hole.
Tip: Use your finger to slide the nut across the plastic bracket surface so that it easily
slips into the recessed cutout.
Important: You need to have the plastic bracket with the hex holes. For N03D, use
PN 920372-01L. For Tx0, use PN 920334-01L. For PxN and Tx0D, use PN
920334-11L. (No hex holes? Contact a Dell sales representative to purchase the
correct bracket for installation.)
2. Attaching the Client VESA Bracket - Select your preferred display orientation, see
note below. The plastic bracket shown below has been positioned for landscape
orientation (for portrait orientation, the plastic bracket must be rotated to the right
before attaching).
Align the screw holes on the plastic bracket (containing the four hex nuts) with the
corresponding holes on client side of the metal P bracket (the side with the release
button) in your preferred display orientation. For N03D, PxN, Tx0 and Tx0D, use the
VESA hole set starting with the inner edge screw holes. Using a Phillips-head
screwdriver attach the provided four (4) M4 screws through the metal bracket, then
through the plastic bracket and into the nut (do not over-tighten).
NOTE: When installing for a monitor in landscape orientation, the client power
button should be facing to the right. When installing for a monitor in portrait
orientation, the plastic bracket must be attached facing down so that when rotated,
the client power button will also be facing to the right.
7
3. Installing the Client for Landscape Orientation - The N03D, PxN, Tx0, or Tx0D
client may now be inserted into the plastic bracket for landscape orientation.
Tip: For portrait orientation, it is best to install the client as the last step.
4. Attaching the Power Adaptor Holder - Install the power adaptor holder on the
P bracket (the side with the release button). Slide the small hooks downward into the
vertical slotted holes and the large hooks onto the top edge of the bracket. Use the
M2.5 screw provided to secure the ‘holder’ on the bracket.
5. Attaching P Bracket to the Monitor - Place the monitor on a padded surface with
the display facing down. Remove the stand from the monitor by pushing the quick
release button. Remove the four (4) VESA screws from the back of the monitor and
set them aside. Position the P bracket's central section on the back of the monitor.
Slide the bracket’s top tabs into the dedicated tab slots, and then firmly push down
bottom edge of bracket until it snaps in place. For additional security, re-install the
monitor VESA screws that you had set aside (do not over-tighten).
CAUTION: If you need to remove the P bracket, remove monitor screws and
then press the lower quick release button on the monitor, not the upper release
button on the bracket.
6. Re-installing the Monitor Stand - Insert the upper stand tabs into dedicated space
on the P bracket and press down until the quick release button latches in.
Place the monitor in the upright standing position.
7. Adjusting and Securing Monitor Height
For landscape orientation - Adjust the monitor height and attach stopper. Make
sure that the stopper tab is facing up on the front side of the stand, and then snap
the stopper ends together.
For portrait orientation - Raise the monitor to ‘maximum’ height and attach
stopper. Make sure that the stopper tab is facing up on the front side of the stand,
and then snap the stopper ends together. Rotate the monitor.
NOTE: The purpose of the stopper is to support the extra weight of the client
and P bracket.
NOTE: If mounting the P bracket on the E2414 Monitor, the stopper does not
need to be used.
8. Installing the Client for Portrait Orientation - The N03D, PxN, Tx0, or Tx0D client
may now be inserted into the plastic bracket for portrait orientation. Make sure that
the power button faces towards the top right.
9. Finishing- Make all desired connections, and then connect the power adapter’s AC
power cable to an electrical outlet.
CAUTION: Do not enclose the client in a confined environment without proper
ventilation.
883964-01 Rev. C
November 2014
©2014 Dell Inc. All Rights Reserved.