Wieland-M36 Rolled Products

Wieland-M36
Rolled Products
CuZn36
C27000
Material Designation
Chemical Composition (Reference)
Typical Applications
EN
CuZn36
Cu
64 %
UNS*
C27000
Zn
balance
· Metal goods
· Deep drawn parts
· Stamped parts
·Connectors
* Unified Numbering System (USA)
Physical Properties*
Electrical
Conductivity
MS/m
%IACS
15
26
Thermal Conductivity W/(m·K)
120
Coefficient
of Electrical
Resistance**
10-3/K
1.7
Coefficient of
Thermal Expansion** 10-6/K
20.2
Density
8.44
g/cm3
Modulus of Elasticity GPa
Specific Heat
110
0.377
J/(g·K)
Poisson’s Ratio
0.34
* Reference values at room temperature
** Between 0 and 300 °C
Fabrication Properties
Corrosion Resistance
Capacity for Being
Cold Worked
excellent
Machinability
fair
Capacity for Being
Electroplated
Good resistance to: fresh water,
neutral or alkaline solutions, organic
compounds as well as land, sea, and
industrial atmosphere.
excellent
Capacity for Being
Hot-Dip Tinned
excellent
Soft Soldering
excellent
Resistance
Welding
good
Gas Shielded
Arc Welding
fair
Laser Welding
less suitable
Not resistant to: acids, hydrous
sulphur compounds, hydrous
ammonia (stress corrosion cracking)
in non-stress-relieved condition.
Mechanical Properties
Temper
R300
R350
R410
R480
410–490
480–560
R550
R630
550–640
M36
≥ 630
MPa
300–370
350–440
Yield Strength Rp0.2
MPa
≤ 180
≥ 170
17
≥ 300
≥ 430
≥ 500
≥ 600
Elongation A50mm
%
≥ 38
≥ 19
16
≥8
≥3
–
–
Temper
H055
H095
H120
H150
H170
H190
Hardness HV
55–95
95–125
120–155
150–180
170–200
≥ 190
Temper
G010
mm
≤ 0.015
El. Conductivity (MS/m)
16
15
14
13
12
R300
H055
R350
H095
R410
R480
H120
H150
Temper
0°
M36
6
13
G030
G050
0.020–0.045
0.035–0.070R630
R350
R410
R480
R550
H095
H150 ≤ 80H170
≤ 90 H120
Temper
H190
Bendability (Strip Thickness t ≤M36
0.5 mm)
M36
17
11
14
11
0.015–0.030
R300
H055
≤ 95
≤ 120
Electrical Conductivity
15
12
G020
R550
H170
R630
H190
Rel. Bending Radius r/t 90°
Grain Size
Hardness HV
El. Conductivity (MS/m)
Tensile Strength Rm
6
5
4
3
bending edge –I rolling direction
bending edge II rolling direction
2
1
0
R300
H055
R350
H095
R410
R480
H120
H150
Temper
R550
H170
R630
H190
Wieland-M36
CuZn36
C27000
190
180
170
160
150
140
130
120
110
100
90
80
70
60
M36
Temper R410
400 °C
500 °C
600 °C
Vickers Hardness HV
Vickers Hardness HV
Resistance
M36to Softening
0
10
20
30
40
Time (min)
50
190
180
170
160
150
140
130
120
110
100
90
80
70
60
60
Temper R550
400 °C
500 °C
600 °C
0
10
20
30
40
Time (min)
50
Vickers hardness
after heat treatment
(typical values)
60
M33 (wh)
Thermal Stress Relaxation
Stress remaining after thermal relaxation as a function of Larson-Miller
parameter (F. R. Larson, J. Miller, Trans
ASME74 (1952) 765–775) given by:
P = (20 + log(t))*(T + 273)*0.001.
Time t in hours, temperature T in °C.
Example: P = 9 is equivalent to
1.000 h/118 °C.
Measured on rolled to temper specimens parallel to rolling direction. Total
stress relaxation depends on the
applied stress level. Furthermore, it
is increased to some extent by cold
deformation.
100
Residual Stress (%)
90
80
70
60
50
40
Temper
R410, R480,
R550, R630
7.0
8.0
9.0
10.0
Larson-Miller parameter P
11.0
Fatigue Strength
The fatigue strength is defined as the maximum bending stress amplitude which a material withstands for 107 load cycles
under symmetrical alternate load without breaking. It is dependent on the temper tested and is about 1/3 of the tensile
strength Rm.
· Standard coils with outside
diameters up to 1400 mm
· Traverse-wound coils with drum weights up to 1.5 t
· Multicoil up to 5 t
Wieland-Werke AG
Dimensions Available
· Hot-dip tinned strip
· Contour-milled strip
· Sheet
· Strip and sheet with protective
coating
www.wieland.com
Graf-Arco-Str. 36, 89079 Ulm, Germany, Phone +49 731 944 2030, Fax +49 731 944 4257, [email protected]
This printed matter is not subject to revision. No claims can be derived from it unless there is evidence of intent or gross negligence.
The product characteristics are not guaranteed and do not replace our experts’ advice.
· Strip thickness from 0.10 mm,
thinner gauges on request
· Strip width from 3 mm,
however min. 10 x strip thickness
10/14 Bm (R+G)
Types and Formats Available