2015 Training Programmes

JUBILEE
TECHNICAL
TRAINING CENTRE
TAKORADI
POLYTECHNIC
2015 TRAINING
PROGRAMMES
Main Courses – Duration: 26 weeks
1. NVQ Level 2 Performing Process Operation in Replicating Environment
2. NVQ Level 2 Performing Engineering Operation in Mechanical
3. NVQ Level 2 Performing Engineering Operation in Electrical
4. NVQ Level 2 Performing Engineering Operation in Instrumentation
JTTC Short appreciation courses in the following disciplines
Process
1. Process Appreciation (2 weeks)
2. P&ID Drawings ( 2 days)
3. Permit To Work System (2 Days)
4. Level Control (1 Day)
5. Pressure Control (1 Day)
6. Plant Safety (3 Days)
Mechanical
1. Mechanical Safety (7days)
2. Risk Assessment (2 days)
3. Gears (5 days)
4. Valves (2 days)
5. Bearings (5 days)
6. Pumps (5 days)
7. Thread Cutting (3 days)
8. Drilling (7 days)
9. Locking Devices (2 days)
10. Measurement (2 days)
11. Seals And Lubrications (2 days)
12. Hand Tools (7 days)
13. Marking Out (5 days)
14. Compressor (5 days)
15. Pipe Fitting (7 days)
16. Hydraulic Systems (5 days)
17. Mechanical Engineering For Non-Mechanical Engineers (5 days)
Electrical
1. Domestic lighting and power installation (1 week)
2. Inspection and testing (1 week)
3. BS7671 IEE Wiring Regulations (3 days)
4. Installation techniques using tray plate, trunking, metallic and non metallic conduits (2
weeks)
5. Electrical health and safety (1 week)
6. Fault diagnosis (3 days)
7. Panel building (1 week)
8. Earthing (3 days)
9. Sizing: cables, conduit and trunking (3 days)
10. Electrical working practices (3 days)
11. Motor maintenance (3 days)
12. Circuit protective devices (3 days)
Instrumentation
COURSES - DURATION: 2 WEEKS
1. Instrument Introduction
2. Pressure Measurement
3. Level Measurement
4. Temperature Measurement
5. Flow Measurement
6. Instrument Fitting
7. Hazardous Areas
8. Cause and Effect Diagrams
9. Loop Diagrams
10. Control Valves
JTTC Health & Safety Short Courses
NO
COURSES
DURATION
Working at Height
2 Days
Lifting Operations
2 Days
Evacuation Work
2 Days
Confined Space
2 Days
Control of substances hazardous to health (Risk assessment)
3 Days
Contractor Management (on site)
2 Days
Environmental Management
2 Days
Fire hazard, control and emergency response
3 Days
First Aid
1 Day
Risk Assessment
3 Days
Permit to Work
1 Day
Energy Isolation
1 Day
Process Safety
2 Days
Management of Change
2 Days
Driving Safety
1 Day
Electrical Safety
3 Days
Job Safety Analysis
2 Days
Organizing for health and safety
3Days
Behavioral safety
2 Days
Promoting a positive health and safety culture
3 Days
Principles of control
2 Days
Movement of people and vehicles-hazards and control
3 Days
Manual and mechanical handling hazards and control
3 Days
Work equipment and hazard controls
2 Days
Ergonomics
3 Days
Chemical and biological health hazards and control
2 Days
Construction activities-hazards and control
2 Days
Incident investigation, recording and reporting
3 Days
Monitoring, review and audit
2 Days
Health and safety legal frame work
3 Days
Certification Course in Occupational Health & Safety Management (5 Days)
Certification Course in Occupational Health, Safety & Environmental Management (7 Days)
Nebosh Health $ Safety International General Certificate (IGC) Level 3 (10 Days)
Other Refresher Courses
 Risk Management
 Overview of Oil & Gas Industry
 Fundamentals of Compressor Systems
 Instrumentation & Control Fundamentals
 Gas Conditioning & Processing
 Operator Training for Oil & Gas Processing Facilities
 Piping Systems- Mechanical Design & Specification
 Mathematics for Instrumentation Technicians
 Fundamentals of Industrial Process, Measurement & Control
 Introduction to industrial Automation
 Technology & Innovation Engineering
 Applied maintenance Management
 Optimizing Preventive & Predictive Maintenance
 Effective Maintenance Shutdowns
 Project Estimation
 Pipeline Engineering Design, Construction & Operation
 Gas Plant Process Engineering
 Gas Plant & Pipeline Management
 Pipeline Control Systems
 Pipeline Costing
 Potable Water Treatment
 Heat Medium, Cooling Systems
 Utilities Management
 Gas Commercialization & Sales Agreements
 Onshore/ Offshore Pipeline Activities
 Fundamentals of Flow Assurance for Pipeline & Piping Systems
 Maintenance Management on Gas Processing Plant
 Heat Exchanger/ Transfer Equipment
 Turbo Machinery Pump & Compressor & Associated Piping Systems
 Welding Engineering
 Troubleshooting of Equipment
 Introduction to High Voltage Electrical Systems
 Safe use of Equipment Hazardous Areas
 Process Control Systems
 Facilities Management
 Programming
 Basic Geophysics
 Soil & Rock Mechanics
 Basic Geotechnical Engineering
 AutoCAD, CivilCAD
 Corrosion Management
 Effective Materials Management
 QA/QC Procedures & Activities
EXPERTISE
The Centre has TTE Consultants and can boost of 12 local partially trained workforces who are
competent to instruct and train.
EQUIPMENT
Process
 3-Phase Separation Plant
 Water Treatment Plant
 Control Room to control the plant DCS
 Mechanical
 Hydraulic press
 Pedestal drills
 Band saw
 Bench drill
 Milling and drilling machine
 Pedestal grinding machine
 Compressors
 Bench vices
 Pumps

Centrifugal

Diaphragm

Gear
 Valves
 Gate
 Check
 Globe
 Ball
 Butterfly
 Induction heater
 Optalign alignment kit
 Shafts
 Mechanical seals
 Hydraulic hoist
Electrical
 Workshop base
 Instrumentation
 Automatic input devices
 Industrial electronics
 AC/DC Electrical systems
 PLC control systems
 Instrument test/calibration bench
 Dead weight tester system
 Process control system
 Basic timer control on delay and off-delay
 Control ladder logic
 Control relays and motor starters
 Systems troubleshooting
 Reversing motor control
 Manual motor control and overload protection
 Introduction to troubleshooting
 Introduction to electric motor control
 Control transformers
QUALIFICATION
AWARDING BODY – PAAVQSET (Process Award Authority Vocational Qualification Science
Engineering Technology), UK for the 26 Week courses.
Certificate of Attendance from JTTC
PARTIALLY TRAINED WORKFORCE UP TO STANDARD
LOCAL INDUSTRIES TO BUY-IN