Installation Guide: CSA-ARCH3-BRKT

Transcription

Installation Guide: CSA-ARCH3-BRKT
CSA-ARCH3-BRKT
QMT™ 3-Series Architectural Shade Hardware
Installation Guide
Description
QMT™ 3-Series Architectural Shade Hardware from Crestron® is a compact mounting
system that allows a Crestron shade to be mounted on a wall, ceiling, pocket, or window
jamb. Extrusions for concealing shades include square or curved fascia, top and back
covers, and pockets. Accessories for creating blackout conditions, such as sill angles and
side channels, are also available.
Additional Resources
Visit the product page on the Crestron website (www.crestron.com) or
scan the QR code to the right for additional information and the latest
firmware updates.
NOTE: End caps are only used in conjunction with a fascia and when outside
mounted. If inside mounted, end caps are not required unless shade brackets
protrude from the window.
Secure the Motor to the Motor Bracket
Left Mounting Bracket: Inside Mount
3. If using end caps, attach the end caps to the mounting brackets following the
stamped directions on the end caps. The end caps snap into place.
4. Fasten the brackets to the outside of the window frame (outside mount) or inside of
the window frame (inside mount) using the appropriate hardware for the mounting
surface. Make sure the brackets are level and on a flat surface for best results. Refer
to the mounting illustrations that follow.
• The idler bracket mounts on the right side of the window opening.
• The motor bracket mounts on the left side of the window opening.
NOTE: The stamped L and R should face the wall and window.
Left Mounting Bracket: Outside Mount
Plastic clips lock the motor into the motor bracket when it is fully inserted
into the motor bracket. Pull the motor gently to the right to ensure that the
motor is securely locked into place.
Install the Brackets
Adjust the Roller Shade Assembly
The CSA-ARCH3-BRKT is mounted to the wall using the two supplied brackets. The end
caps (optional) and roller shade assembly then attach to the brackets. Refer to the
following illustrations for bracket dimensions.
Dimensions: Mounting Bracket (Dimensions are the same for both brackets)
NOTE: For inside mounts, mounting brackets may be screwed into the window jamb
(as pictured above) or into the window header.
NOTE: When using a fascia, align the brackets with the width of the fascia before
screwing them to the header.
1/2 in
(13 mm)
0.70 in
(18 mm)
Mount the Roller Shade Assembly
CAUTION: There is risk of personal injury and equipment damage if the shade or
associated parts fall during installation. Use care when installing. Use proper mounting
hardware (e.g., screws or bolts) for the mounting surface when securing the brackets to
the surface.
11/16 in
(18 mm)
1 1/2 in
(37 mm)
Once the roller shade assembly is installed, adjustments can be made to level the shade
and center it in the opening. Refer to the illustration below for adjustment options. If
adjustments do not fix leveling or centering issues, remount the brackets or shim the
fabric. If shade fabric is telescoping to the left, shim the right side of the fabric.
Right Mounting Bracket: Outside Mount
2 15/16 in
(75 mm)
1 9/16 in
(41 mm)
Once the mounting brackets are installed, the roller shade assembly should be installed.
1. Insert the idler pin into the top of the keyhole on the right bracket and slide it down
into the keyhole. The idler pin sits on the vertical adjustment screw.
Insert the Idler Pin into the Keyhole
Tighten or loosen the
screw to level the
shade.
2 1/2 in
(58 mm)
2 15/16 in
(75 mm)
1 1/2 in
(37 mm)
11/16 in
(18 mm)
Loosen the screws, adjust the shade so that it
is centered in the opening, and then tighten the
scews to lock the shade into place.
Swap the Idler and Motor Ends
5/16 in
(8 mm)
11/16 in
(18 mm)
Vertical Adjustment
Screw
1/2 in
(13 mm)
Right Mounting Bracket: Inside Mount
11/16 in
(18 mm)
1/2 in
(13 mm)
CAUTION: There is risk of personal injury and equipment damage if the shade or
associated parts fall during installation. Use care when installing. Use proper mounting
hardware (e.g., screws or bolts) for the mounting surface when securing the brackets to
the surface.
NOTE: The screws that are provided with the mounting brackets are intended for use
on walls (or jambs) with wood or metal blocking. Screws should not be used for hollow
drywall or masonry installations. It is the responsibility of the installer to ensure that
mounting method used is secure.
Install the brackets.
1. Hold the roller shade assembly in the approximate mounting location and check for
a proper fit. If using a fascia, use the fascia to help measure the proper distance
between mounting brackets.
2. Ensure that the mounting points are level with each other and mark the locations of
the brackets.
2. Raise the motor end of the roller shade assembly to the motor bracket.
3. Push the roller shade assembly towards the idler bracket to compress the spring on
the idler pin and align the tab on the motor assembly with the hole in the motor
bracket.
Align the Motor with the Motor Bracket
NOTE: When the bracket is
installed inside a pocket,
the motor must be rotated
90 degrees from what is
shown in the image to the
right and then raised past
the tab. Rotate the motor so
it aligns with the mounting
bracket.
Maneuver the
motor end into
the bracket slot.
4. Push the tab on the motor assembly into the hole in the motor bracket. When the
shade is properly seated, the two clips spring down to secure the motor to the
bracket. Ensure the shade is properly mounted before letting go.
The roller shade assembly can be mounted with the idler and motor ends on different
ends of the tube than they were when they were received from the factory (i.e., the idler
end is on the left and the motor end is on the right). Swapping the idler and motor ends
allows the roller shade to still roll off of the proper side of the tube. This might be
necessary if the control or power wires were run to the wrong side of the window. If this is
necessary, the idler mount in the right bracket and motor mount in the left bracket will
need to be swapped. The left and right mounting brackets remain on their intended side.
Swap the Bracket Hardware
Swapping the hardware requires a Phillips screwdriver.
1. Remove the two screws holding the motor mount in the left hand bracket. Note the
orientation of the motor mount and then remove it along with the two screws. Retain
all hardware for reinstallation.
Screws
Motor Mount
Left Bracket
2. Remove the two screws holding the ilder mount in the right hand bracket. Note the
orientation of the idler mount and then remove it along with the two screws. Retain
all hardware for reinstallation.
3. Remove the four screws from the back of the idler mount and separate the
assembly.
Screws
Screws
Mount the Fascia
Wiring
Once the assembly is installed and programmed, the fascia can be mounted.
Align the fascia with the mounting brackets and then press the fascia into place. The
fascia assembles into place by snapping onto the tabs on the bracket. Place the top of the
fascia on the top of the bracket first and then press the bottom of the fascia into place on
the bottom of the bracket.
To remove the fascia, pull the bottom of the fascia down to clear the bottom tab on the
bracket. Then, pull the fascia away from the window and upwards to release the top of the
fascia. Refer to the illustrations below.
Programming
Do not use CRESNET-HP cable with the small connector. When using CRESNET-HP cable,
the connector on the motor pigtail must be replaced with the larger connector that is
supplied with the shade.
All shades should be home run from the controlling device.
The left and right brackets provide a cutout in the upper corner, which allows wiring to be
easily run to the motor.
Use a cable tie
around the loop to
secure the wire.
Before the roller shade can be operated, the device must be programmed and set up. For
information on programming and setup of this device, refer to Digital QMT Shade Motor
Programming Guide (Doc. 7437) at www.crestron.com/manuals.
Wire Exit
Right Bracket
Idler Mount (Dissassembled)
4. Without rotating or flipping the motor mount, transfer it from the left hand bracket
to the right hand bracket. Reassemble using the screws removed earlier.
Refer to the illustration that follows for wiring details.
Wire the Cresnet QMT Motor with the Power and Control Coming from the Same Source
Power
Supply and
Cresnet
Control
QMT Motor
Red
White
5. Without rotating or flipping the idler mount, transfer it from the right hand bracket to
the left hand bracket. Reassemble using the screws removed earlier.
Blue
Black
Wire the Cresnet QMT Motor with the Power and Control Coming from Separate Sources
Rotate 180 degrees.
Do not flip.
Cresnet
Control
Do not flip or rotate.
QMT Motor
Local Power
Supply
Swap the Roller Shade Motor and Idler End
Swap the idler and motor end of the roller shade.
1. Remove the motor by pulling on the motor head.
2. Use the idler removal tool to loosen the idler by rotating the idler counter clockwise.
Pull the idler out of the tube.
3. Reinstall the motor into the opposite end of the tube.
4. Reinstall the idler into the opposite end of the tube.
5. Use the idler removal tool to tighten the idler; rotate the idler clockwise two turns
and then tighten until snug. Pull on the idler to confirm it is properly secured.
Red
White
Top and Back Cover (Optional)
NOTE: If the top and back cover
is used, the fascia rests in the lip
of the top and back cover.
Blue
Black
Wire the infiNET EX QMT Motor
The fascia snaps to the top of the
bracket.
infiNET EX
QMT Motor
Power
Supply
Red
Black
The fascia snaps to the bottom
of the bracket.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions:
(1) This device may not cause harmful interference and (2) this device must accept any interference
received, including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna
•
Increase the separation between the equipment and receiver
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected
•
Consult the dealer or an experienced radio/TV technician for help
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at patents.crestron.com.
Crestron, the Crestron logo, Cresnet, infiNET EX, and QMT are either trademarks or registered
trademarks of Crestron Electronics, Inc. in the United States and/or other countries. Other
trademarks, registered trademarks, and trade names may be used in this document to refer to
either the entities claiming the marks and names or their products. Crestron disclaims any
proprietary interest in the marks and names of others. Crestron is not responsible for errors in
typography or photography.
This document was written by the Technical Publications department at Crestron.
©2015 Crestron Electronics, Inc.
Crestron Electronics, Inc.
15 Volvo Drive Rockleigh, NJ 07647
Tel: 888.CRESTRON
Fax: 201.767.7576
www.crestron.com
Installation Guide - DOC. 7732A
(2042807)
02.15
Specifications subject to
change without notice.