GAT10 Series Catalogue PDF

Shimaden, Temperature and Humidity Control Specialists
°C
%RH
Series GAT10
SHIMADEN COMMUNICATION ADAPTOR
GAT10-DN
GAT10-CC
• DeviceNet is a registered trademark of ODVA
(Open DeviceNet Vendor Associations, Inc.).
• The CC-Link is the open field network of the
CC-Link Association.
BASIC FEATURES
Best solution for PLC-Shimaden application!
Up to 8 Shimaden Controllers can be controlled through
DeviceNet / CC-Link.
Enables easy (programless) access to all parameters from
Master PLC.
No manual configuration required.
Quick response - Scan time for 8 Controllers: approx.
1.5 sec.
Provides cost-effective "Less Wiring" networking and
"Application Flexibility" solution to total system integration,
especially, to wide spread device installation.
DeviceNet/RS-485 Protocol Converter
GAT10-DN
GAT10-DN
• A programless communication between any controller using the
Shimaden standard protocol and the DeviceNet is made
possible.
• It allows measured values and set values of temperature and the
parameters of a maximum of eight Shimaden products having
the RS-485 communication function to be read and written
through the DeviceNet Master PLC.
• When various units are installed separately in different devices,
the amount of wiring for an entire system can be reduced.
ORDERING INFORMATION
Items
SERIES
NETWORK SYSTEM
CODE
GAT10DN9008-
POWER SUPPLY
0
9
REMARKS
SPECIFICATIONS
Protocol Converter
DeviceNet
100~240V AC 10% (50/60Hz)
24V AC (50/60Hz) / DC 10%
Without
With (Please consult before ordering.)
EXAMPLE SYSTEM CONFIGURATIONS
DeviceNet Master PLC
GAT10-DN
Other slave stations of DeviceNet
Scan times average
1.5 seconds or shorter
(when connected with
8 controllers)
RS-485 (Shimaden standard protocol)
Up to 8 controllers
Supported Models List
Digital controller:
Programmable controller:
SR90, SR80, SR253
FP93
Digital indicator: SD16
Servo controller: EM70
DeviceNet is a registered trademark of ODVA (Open DeviceNet Vendor Associations, Inc.).
SPECIFICATIONS
Model
• GAT10-DN
Display (LED)
• Confirmation of power 'on'
• DeviceNet Status
: DeviceNet Protocol Converter
: POWER (Green)
: MS (Green/Red: module status)
: NS (Green/Red: network status)
• RS-485 Communication
: RX (Green: during receiving)
: TX (Green: during transmission)
DeviceNet/Setting of communication speed
• Setting system
: by front dip switches
• Station No.
: 0~63
Communication speed
: 125k, 250k, 500k bps
Network
• DeviceNet applicable specifications : Volume 1 Release 2.0
: Volume 2 Release 2.0
• RS-485 Communication speed
: 19,200bps fixed
Data format
: Data 7 bits
Even parity
Stop 1 bit
Communication protocol
: Shimaden standard protocol
Connectable products
: SR90, SR80, SR253, SD16, FP93,
EM70
The number of connectable products : Max. 8 (excluding this instrument)
General Specification
• Environmental conditions for instrument operation,
Ambient Temperature : –10~50˚C
Ambient Humidity
: 90% RH (no dew condensation)
Altitude
: 2000m from the sea level or lower
Category
: II
Degree of pollution
:2
• Storage temperature
: –20~65˚C
• Supply voltage
: 100~240V AC±10% 50/60Hz
24V AC±10% 50/60Hz
24V DC±10%
• Power consumption
: 5VA (100~240V AC)
: 4VA (24V AC)
: 3W (24V DC)
• Conformity with standards
: IEC61010-1 and EN61010-1
• Insulation resistance
Between input/output terminals and power terminal
: 500V DC 20 MΩ or above
Between input/output terminals and ground terminal
: 500V DC 20 MΩ or above
• Dielectric strength
Between input/output terminals and power terminal
: 2300V AC 1 minute (Faradic current 3mA)
Between power terminal and ground terminal
: 1500V AC 1 minute (Faradic current 3mA)
• Material of case
: PPO resin molding
• Color of case
: Black
• External dimensions
: H80 × W50 × D120mm
(including base, excluding front connector)
• Mounting
: DIN rail/fixed by screw
• Weight
: Approx. 250g
CC-Link/RS-485 Protocol Converter
GAT10-CC
GAT10-CC
• A programless communication between any controller using the
Shimaden standard protocol and the CC-Link is made
possible.
• It allows measured values and set values of temperature and the
parameters of a maximum of eight Shimaden products having
the RS-485 communication function to be read and written
through the CC-Link.
• When various units are installed separately in different devices,
the amount of wiring for an entire system can be reduced.
ORDERING INFORMATION
Items
SERIES
NETWORK SYSTEM
CODE
GAT10CC9008-
POWER SUPPLY
0
9
REMARKS
SPECIFICATIONS
Protocol Converter
CC-Link
100~240V AC 10% (50/60Hz)
24V AC (50/60Hz) / DC 10%
Without
With (Please consult before ordering.)
EXAMPLE SYSTEM CONFIGURATIONS
CC-Link master station
PLC (Product of Mitsubishi Electric)
GAT10-CC
Other slave stations of CC-Link
SR-83
(specified for use in CC-Link system)
Scan times average
1.5 seconds or shorter
(when connected with
8 controllers)
RS-485 (Shimaden standard protocol)
Up to 8 controllers
Supported Models List
Digital controller:
Programmable controller:
SR90, SR80, SR253
FP93
Digital indicator: SD16
Servo controller: EM70
The CC-Link is the open field network of the CC-Link Association.
SPECIFICATIONS
Model
• GAT10-CC
Display (LED)
• Confirmation of power 'on'
• CC-Link Status
: CC-Link Protocol Converter
: POWER (Green)
: LRUN
(Green: establishing communication link)
: LERR (Orange: communication error)
: RD (Green: during receiving)
: SD (Green: during transmission)
• RS-485 Communication
: RX (Green: during receiving)
: TX (Green: during transmission)
CC-LINK Station No./Setting of communication speed
• Setting system
: by 3 front rotary dip switches
• Setting range, Station No.
: 1~61
Communication speed
: 156k, 625k, 2.5M, 5M, 10M bps
Network
• CC-Link Version
: 1.10
Type of station
: Remote device station
The number of occupying stations
:4
• RS-485 Communication speed
: 19,200bps fixed
Data format
: Data 7 bits
Even parity
Stop 1 bit
Communication protocol
: Shimaden standard protocol
Connectable products
: SR90, SR80, SR253, SD16, FP93,
EM70
The number of connectable products : Max. 8
General Specification
• Environmental conditions for instrument operation,
Ambient Temperature : –10~50˚C
Ambient Humidity
: 90% RH (no dew condensation)
Altitude
: 2000m from the sea level or lower
Category
: II
Degree of pollution
:2
• Storage temperature
: –20~65˚C
• Supply voltage
: 100~240V AC±10% 50/60Hz
24V AC±10% 50/60Hz
24V DC±10%
• Power consumption
: 10VA (100~240V AC)
: 5VA (24V AC)
: 4W (24V DC)
• Conformity with standards
: IEC61010-1 and EN61010-1
• Insulation resistance
Between input/output terminals and power terminal
: 500V DC 20 MΩ or above
Between input/output terminals and ground terminal
: 500V DC 20 MΩ or above
• Dielectric strength
Between input/output terminals and power terminal:
: 2300V AC 1 minute (Faradic current 3mA)
Between power terminal and ground terminal
: 1500V AC 1 minute (Faradic current 3mA)
• Material of case
: PPO resin molding
• Color of case
: Black
• External dimensions
: H80 × W50 × D130mm (including base)
• Mounting
: DIN rail/fixed by screw
• Weight
: Approx. 260g
Series
GAT10
20
GAT10-DN
DeviceNet status LED
80
MS
NS
RX
TX
V–
CAN_L
Drain
CAN_H
RESET POWER
V+
SHIMADEN
RS-485 Communitation
status LED
7.8 0.2
Hole of
4.5 in diameter
35.4
MS: Module status LED
Lit in green when the
module is functioning
normally.
NS: Network status LED
Lit in green when the
module is communicating
with the network normally.
8-M3.5 7
Approx. 2
100
Transmission rate
setting switch (SW6, SW7)
81 maximum
120
(NA0~NA5)
40 0.2
51 maximum
Approx. 4
50
Mountable on DIN rail
GAT10-DN EXTERNAL DIMENSIONS AND TERMINAL ARRANGEMENT DIAGRAM
Front View
Node address setting switch
Transmission rate setting
Unit: mm
Transmission rate SW6 SW7
RX: Blink in green when the
module is receving
data from controller.
TX: Blink in green when the
module is sending data
to controller.
125kbps
OFF OFF
250kbps
ON OFF
500kbps
OFF ON
Inhibition of setting ON
Terminal Layout
6 5 4 3
ON
Reset switch
(for resetting the module)
7 8 1 2
Signal
No.
1
2
3
4
5
6
7
8
RS-485
FG
N
L
Power
supply
SG
RS-485
DeviceNet connector
Note: A set value becomes effective upon applying power or resetting.
For details, see "DeviceNet Specification" issued by ODVA.
GAT10-CC EXTERNAL DIMENSIONS AND TERMINAL ARRANGEMENT DIAGRAM
Front View
×1
30
This apparatus is of the 4
possessory station type.
Set the number of the first
station.
The setting range is from
01 to 61.
The factory set value is 00.
7.8 0.2
Approx. 2
100
51 maximum
Hole of
4.5 in diameter
81 maximum
×10
130
35.4
GAT10-CC
B.RATE
11-M3.5 7
Switch for setting
CC-Link station
numbers.
Mountable on rail
50
CC-Link transmission
rate setting switch
80
RESET
POWER
RX
SD
TX
SHIMADEN
Operating condition of
CC-Link is displayed.
Transmission rate setting
Position Transmission rate
Operating condition of
RS-485 communication is
displayed.
0
156kbps
1
625kbps
2
2.5Mbps
3
Reset switch
(for resetting the module)
Approx. 4
LRUN LERR RD
4
5Mbps
10Mbps
Factory set value is 156kbps.
40 0.2
Unit: mm
Terminal Layout
8 7 6 5
4
9
3
10 11 1 2
No.
Signal
1
2
3
4
5
6
7
8
9
10
11
RS-485
SG
FG
Power
N
supply
L
FG
SLD
DG CC-Link
DB
DA
Note: A set value becomes effective upon applying power or resetting.
For details, see "CC-Link Specification" issued by the CC-Link Association
Warning
• The GAT10 series is designed to control temperature, humidity and other physical quantities of general industrial equipment. (It should not be used to
control any object which might seriously affect the safety of personnel.)
Caution
• In case it is feared that a failure of this apparatus will impair or damage the system or any other property, take appropriate measures for failure prevention
before use of the apparatus is begun.
The names of the companies and products described in this brochure are their registered trademarks.
(The contents of this brochure are subject to change without notice.)
Temperature and Humidity Control Specialists
ISO 9001
Head Office: 2-30-10 Kitamachi, Nerima-Ku, Tokyo 179-0081 Japan
Phone: +81-3-3931-7891 Fax: +81-3-3931-3089
E-MAIL: [email protected] URL: http://www.shimaden.co.jp
03LGAT10300ILC