Mixed Alkanolamines with Low Regeneration Energy for CO2

Available online at www.sciencedirect.com
Energy Procedia 37 (2013) 455 – 460
GHGT-11
Mixed Alkanolamines with Low Regeneration Energy for
CO2 Capture in a Rotating Packed Bed
Cheng-Hsiu Yu and Chung-Sung Tan*
Department of Chemical Engineering, National Tsing Hua University, Hsinchu, Taiwan, R. O. C
Abstract
In this study, the concentrated piperazine (PZ) and mixed PZ + diethylenetriamine aqueous solutions were used as
the absorbents to capture CO2 from a nitrogen gas stream containing 10% of CO2 in a rotating packed bed (RPB). To
reduce the heat of vaporization of absorbent in regeneration, diethylene glycol was added into the concentrated PZ
aqueous solution. The higher gas-liquid contact area and mass transfer rate as well as the smaller size were observed
in a RPB as compared with a packed bed to achieve the same CO2 capture efficiency.
© 2013
Elsevier
Ltd.Ltd.
2013 The
TheAuthors.
Authors.Published
Publishedbyby
Elsevier
Selection
of GHGT
Selectionand/or
and/orpeer-review
peer-reviewunder
underresponsibility
responsibility
of GHGT
Keywords: CO2 Capture, Chemical absorption, Alkanolamine, Diethylenetriamine, Piperazine, Diethylene glycol, Rotating packed
bed
1. Intoduction
The global warming issue which resulted from greenhouse gases has received widespread concern
nowadays. Among the greenhouse gases, the contribution of carbon dioxide (CO2) to global warming is
more than 60%. Coal supplies 25% world energy and 40% of carbon emission, and therefore it is essential
to capture and storage CO2, especially from fossil fuel power generation plants to cope with the global
demanding of CO2 reduction [1, 2].
Chemical absorption has been used to treat acid gases, such as SO2 and CO2 in packed bed. However,
the drawback of using packed bed is that large volume is required to treat a huge amount of the exhausted
gas ffrom power plant and significant mass transfer limitations exist in the gas-liquid interface. To
enhance mass transfer rate between gas and liquid, a RPB device was suggested. Not like a packed bed,
liquid contacts with gas on the surface of packing under high centrifugal condition in a RPB, and hence
the gas-liquid contact area as well as the mass transfer efficiency is increased owing to liquid is split into
small droplets and liquid film by passing through the packing. Many studies have been reported to use
various aqueous alkanolamine solutions to capture CO2 in RPB. The results indicated that the size of a
* Corresponding author. Tel.: +886-3-572-1189 ; fax: +886-3-572-1684 .
E-mail address: [email protected] .
1876-6102 © 2013 The Authors. Published by Elsevier Ltd.
Selection and/or peer-review under responsibility of GHGT
doi:10.1016/j.egypro.2013.05.131
456
Cheng-Hsiu Yu and Chung-Sung Tan / Energy Procedia 37 (2013) 455 – 460
RPB could be reduced significantly as compared with a packed bed when the same CO2 capture
efficiency was desired to achieve [3-8].
Alkanolamine-based absorbents such as monoethanolamine, diethanolamine, methyldiethanolamine
and their mixtures as well are commonly used to capture CO2. From our previous work, it can be seen
that diethylenetriamine (DETA) and piperazine (PZ) are preferred to be used in a RPB to capture CO2
because of their high reaction rate. Since there is the solubility limitation for PZ in water, 14% at 293 K,
PZ is usually used as the promoter to mix with other alkanolamines for the enhancement of reaction rate
with CO2. In a recent report by Freeman et al. [9], the concentrated PZ solution was suggested owing to
its effective resistant to oxygen degradation and thermal degradation. However, research related to the use
of the concentrated PZ aqueous solution for CO2 capture in a RPB is limited.
In this study, the concentrated PZ solution was used as the absorbent to capture CO2 because of its fast
reaction rate with CO2. A mixture of DETA and PZ, which had been proposed to be an effective
absorbent in our previous study, was also used for the comparison of CO2 capture efficiency purpose. To
reduce the latent heat of vaporization of absorbents, diethylene glycol (DEG) was proposed to add into
the concentrated PZ aqueous solution. The energy required in the regeneration process was found to
reduce because the reduction of vapor pressure after the addition of DEG.
Nomenclature
ri
Inside radius of the RPB (cm)
ro
Outside radius of the RPB (cm)
Yi
CO2 Concentration in the feed stream (%)
Yo
CO2 Concentration in the discharged stream (%)
2. Experimental
PZ, DETA, and DEG with a purity of 99% were purchased from Seedchem, Aldrich, and Tedia,
respectively. N2 with a purity of 99.99% and CO2 with a purity of 99.5% were purchased from Boclh
Industrial Gases Co (Taiwan). All the chemicals and gases were used as received. The schematic diagram
of the RPB used in this study is shown in Fig. 1.The inner, outer diameters and height of the packing were
2.5, 12.5 and 2.3 cm, respectively. The total volume of the packing in the RPB was of 270.9 cm3. The
stainless wire mesh was used as the packing with a surface area of 887.6 m2/m3 and a void fraction of
0.96.
The gas stream flowed from the outer side into the RPB. The absorbent was pumped from the central
axis tube into the RPB. Both gas and liquid were heated by the heaters equipped with temperature
controller before entering the RPB. The CO2 gas contacted with the absorbent counter-currently in the
RPB. After absorption, the gas stream left from the axis of the RPB and CO2-rich absorbent was
discharged from the outer side of the RPB. The CO2 concentrations of both the feed and discharged gas
stream were measured by a NDIR CO2 analyzer (Drager, Polytron IR CO2). The CO2 capture efficiency
Cheng-Hsiu Yu and Chung-Sung Tan / Energy Procedia 37 (2013) 455 – 460
and height of transfer unit (HTU) were used as the indicators for the absorbent comparison, and they were
calculated by the Eqs (1) and (2):
CO2 Capture efficiency
HTU
Yi - Y
Yi
100% (1)
ro ri
(2)
Yi
ln( )
Yo
where ro and ri are the outside and inside radiuses of the RPB, respectively. Yi and Yo are CO2
concentration in the feed and discharged stream, respectively. A smaller HTU value represents a smaller
reactor volume needed for capturing CO2.
Fig. 1. Experimental apparatus for CO2 capture in a rotating packed bed.
3. Results and Discussion
In our previous work, it had been found that the CO2 capture efficiency of DETA was superior to that
of MEA in a RPB. Besides, the absorbent 15% DETA/15% PZ/70% H2O was an effective absorbent to
achieve a high CO2 capture efficiency in a RPB [8]. This absorbent was therefore chosen for the
comparison purpose. Table 1 shows the CO2 capture efficiencies of various absorbents at the operation
conditions as a temperature of 323 K, a gas flow rate of 30 L/min, a liquid flow rate of 100 mL/min, and a
rotating speed of 1300 rpm. It is seen that the CO2 capture efficiency of the solution 40.8% PZ/59.2%
H2O was higher than that of the mixed alkanolamine aqueous solution 15% DETA/15% PZ/70% H2O,
and the CO2 capture efficiency of the solution 40.8% PZ/47.36% H2O/11.84% DEG was slightly lower
than that of the solution 15% DETA/15% PZ/70% H2O. The difference of CO2 capture efficiency among
the used absorbents was believed mainly due to the different reaction rates with CO2. Because of the
contact time between gas and liquid was very short in a RPB, the absorbents possessing higher reaction
457
458
Cheng-Hsiu Yu and Chung-Sung Tan / Energy Procedia 37 (2013) 455 – 460
Table 1. CO2 capture efficiency and HTU for various absorbents
Absorbent
Content (%)
CO2 Capture efficiency (%)
HTU (cm)
DETA/PZ/H2O
15/15/70
80.0
3.1
PZ/H2O
40.8/59.2
85.0
2.6
PZ/H2O/DEG
40.8/47.36/11.84
77.5
3.4
rates with CO2 would result in higher CO2 capture efficiencies. Because the reaction rate of PZ with CO2
is higher than that of DETA, the CO2 capture efficiency of 40.8% PZ/59.2% H2O was therefore higher
than the mixed solution 15% DETA/15% PZ/70% H2O.
As shown in Table 1 that the CO2 capture efficiency of 40.8% PZ/47.36% H2O/11.84% DEG was
lower than that of 40.8% PZ/59.2% H2O. This was probably due to that the reaction rate of absorbent with
CO2 is proportional to the solubility parameter of solvent [10]. As can be seen from table 2, the solubility
parameter of DEG is lower than water, and hence, the reaction rate of 40.8% PZ/47.36% H2O/11.84%
DEG was therefore lower than that of 40.8% PZ/59.2% H2O, leading to a lower CO2 capture efficiency as
compared to 40.8% PZ/59.2% H2O.
Table 2. Solubility parameter of various solvents [11]
Solvent
Water
DEG
Solubility parameter (J/m3)1/2
48.1
24.8
It can also be seen from Table 1 that the HTU values of the absorbents used in this study were all
lower than 3.4 cm, lower than that of the conventional packed bed where the HTU value is generally
found to be about 340 cm [12]. The significant decrease of HTU using RPB was believed due to the
increased gas-liquid contact area and mass transfer rate in a RPB as compared with a packed bed, and
hence, the smaller size of a RPB was therefore required to achieve the same CO2 capture efficiency.
The regeneration energy estimated in this study was based on the following assumptions: (1) ideal
mixing, (2) CO2-rich loading as 0.82 mol of CO2/mol of amine, (3) regeneration efficiency of 50%, (4)
at 393 K, and (6) regeneration
temperature approach as
pressure at 2 atm. The thermal properties including heat of reaction with CO2 and heat capacity of DETA
and PZ are listed in Table 3. These properties were used for estimation of regeneration energy required.
Fig. 2 shows the regeneration energy required for the solution 40.8% PZ/59.2% H2O was lower than that
of 15% DETA/15% PZ/70% H2O. This was due to that the heat of reaction of PZ with CO2 is lower than
DETA and the PZ concentration in the concentrated PZ solution was higher than that of the solution 15%
DETA/15% PZ/70% H2O, resulting in the lower heat of vaporization of water. In Table 1, the
regeneration energy of 40.8% PZ/47.36% H2O/11.84% DEG was found to be lower than that of 40.8%
PZ/59.2% H2O. Obviously, the heat of vaporization of water could be reduced with the addition of DEG
into the solution. Hence the addition of the low vapor pressure solvents, such as DEG, might be a remedy
to reduce the energy required in the regeneration process.
Cheng-Hsiu Yu and Chung-Sung Tan / Energy Procedia 37 (2013) 455 – 460
Table 3. Thermal properties of DETA and PZ [13-15].
Absorbent
Heat of reaction with CO2 (kJ/mol)
Heat capacity (J/g/K)
4.0
PZ
73
70
2.83
2.51
Regeneration temperature = 393 K
Regeneration pressure = 2 atm
3.5
Regeneration energy (GJ/tonne CO2)
DETA
3.0
2.5
2.0
1.5
1.0
0.5
0.0
15% DETA/15% PZ/70% H2O
40.8% PZ/59.2% H2O 40.8% PZ/47.36% H2O/11.84% DEG
Fig. 2. Regeneration energy of various absorbents.
4. Conclusions
The concentrated PZ solution was verified to be a very powerful absorbent to capture CO2 in a rotating
packed bed absorber because of its fast reaction rate with CO2. However, the absorption should be carried
out at high temperatures because its solubility in water is limited. The mixed alkanolamine solution
containing PZ and DETA was found to be an appropriate absorbent for CO2 capture in RPB regarding
both CO2 capture efficiency and HTU. The HTU obtained using the proposed alkanolamine aqueous
solutions in a RPB were found to be significantly smaller than those in the conventional packed bed,
indicating the volume of an absorber could be reduced with great extent when RPB instead of packed bed
is employed. To reduce the energy required in the regeneration of CO2-loaded absorbent, the addition of a
solvent that can reduce the vapor pressure of the solution such as DEG is a possibility; however, the
penalty is to reduce CO2 capture efficiency; fortunately, the reduction was not too much.
459
460
Cheng-Hsiu Yu and Chung-Sung Tan / Energy Procedia 37 (2013) 455 – 460
Acknowledgements
The authors wish to express their thanks to the financial support from ROC National Science Council
(grant number NSC 101-3113-E-007-005) and National Tsing Hua University at Hsinchu, Taiwan, ROC.
References
[1]Yu CH, Huang CH, Tan CS. A Review of CO2 Capture by Absorption and Adsorption. Aerosol and Air Quality Research
2012;12:745-769.
[2]Pan SY, Chang EE, Chiang PC. CO2 Capture by Accelerated Carbonation of Alkaline Wastes: A Review on Its Principles and
Applications. Aerosol and Air Quality Research 2012;12: 770-791.
[3]Lin CC, Liu WT, Tan CS. Removal of Carbon Dioxide by Absorption in a Rotating Packed Bed. Industrial and Engineering
Chemical Research 2003;42:2381-2386.
[4]Tan CS, Chen JE. Absorption of Carbon Dioxide with Piperazine and Its Mixtures in a Rotating Packed bed. Separation and
Purification Technology 2006;49:174-180.
[5]Cheng HH, Tan CS. Carbon Dioxide Capture by Blended Alkanolamines in Rotating Packed Bed. Energy Procedia 2009;1:925932.
[6]Cheng HH, Shen JF, Tan CS. CO2 Capture from Hot Stove Gas in Steel Making Process. International Journal of Greenhouse
Gas Control 2010;4:525-531.
[7]Cheng HH, Tan CS. Removal of CO2 from Indoor Air by Alkanolamine in a Rotating Packed Bed. Separation and Purification
Technology 2011;82:156-166.
[8]Yu CH, Cheng HH, Tan CS. CO2 Capture by Alkanolamine Solutions Containing Diethylenetriamine and Piperazine in a
Rotating Packed Bed. International Journal of Greenhouse Gas Control 2012;9:136-147.
[9]Freeman SA, Dugas R, Van Wagener DH, Nguyen T, Rochelle GT. Carbon Dioxide Capture With Concentrated, Aqueous
Piperazine. International Journal of Greenhouse Gas Control 2010;4:119-124.
[10]Park SW, Lee JW, Choi BS, Lee JW. Absorption of Carbon Dioxide into Non-aqueous Solutions of N-methyldiethanolamine.
Korean Journal of Chemical Engineering 2006;23:806-811.
[11]James EM. Physical Properties of Polymers Handbook. 2nd ed. 2005.
[12]Jassim MS, Rochelle GT, Eimer D, Ramshaw C. Carbon Dioxide Absorption and Desorption in Aqueous Monoethanolamine
Solutions in a Rotating Packed Bed. Industrial and Engineering Chemical Research 2007;46:2823-2833.
[13]Kim I, Svendsen HF. Comparative Study of the Heats of Absorption of Post-combustion CO2 Absorbents. International Journal
of Greenhouse Gas Control 2011;5:390-395.
[14]Steele WV, Chirico RD, Knipmeyer SE, Nguyen A, Smith NK. Thermodynamic Properties and Ideal-gas Enthalpies of
Formation for Dicyclohexyl Sulfide, Diethylenetriamine, Di-n-octyl Sulfide, Dimethyl Carbonate, Piperazine, Hexachloroprop1-ene, Tetrakis(dimethylamino)ethylene, N,N-Bis-(2-hydroxyethyl)ethylenediamine, and 1,2,4-Triazolo[1,5-a]pyrimidine.
Journal of Chemical and Engineering Data 1997;42: 1037-1052.
[15]Chen YR, Caparanga AR, Soriano AN, Li MH. Liquid Heat Capacity of the Solvent System (Piperazine + nMethyldiethanolamine + Water). The Journal of Chemical Thermodynamics 2010;42:54-59.