Six weeks Industrial training

Transcription

Six weeks Industrial training
The Institution of Electronics and Telecommunication Engineers (IETE)
Chandigarh Centre
IETE Building, Opp. CSIO Colony, Sector 30-B, Chandigarh-160030
Telephone No..: 0172-2651061, Telefax: 0172-2657333
E-mail: [email protected], [email protected]
Website: http://www.ietechandigarh.org
No.;IETE/ Indl Trg/2015
Dated: April 17, 2015
CHAIRMAN
SH. SURINDER KUMAR ANGRA
(M) 09888947997
IMMDT. PAST CHAIRMAN
Subject: Six weeks Industrial /Institution /Summer Training of DIPLOMA & B.Tech Students
nd th th
during 2 /4 /6 Semesters as per University Norms on Nominal Payment Basis during May
2015 to August 2015
DR. C. GHANSHYAM
(M) 09815363532
Kind attention: Training & Placement Officer/HOD/Director/Principal/ISF Co-ordinator
HONORARY SECRETARY
Greetings from IETE Chandigarh Centre,
DR. NEELESH KUMAR
(M) 09478515278
We are please to inform you that IETE Chandigarh Centre is extending its Facilities and Resources to
impart 6 Weeks Industrial, Institution & Summer/Practical training to Diploma & B.E. /B.Tech
students of Electronics & Communication Engineering (ECE) in its complex located in Sector 30, Near
CSIO, Chandigarh.
HONORARY TREASURER
DR.,PIYUSH KUMAR AWASTHI
(M) 09417070212
VICE CHAIRMAN
GP. CAPT. R. C. GOYAL VSM (RETD)
(M) 09815864368
EXECUTIVE MEMBER
DR. ASHOK KUMAR PAUL
(M) 09814969077
DR. G.S. SINGH
(M) 09417495512
SH. SUBHASH CHANDER JAIN
(M) 09878692912
Founded in 1953, The Institution of Electronics & Telecommunication Engineers (IETE) is a leading
professional society devoted to the advancement of S&T in Electronics, Telecommunications,
Information Technology, Computer Science and other related disciplines. IETE serves its more than
70,000 members both individuals, corporate, industries and organizations through its 65 centres
spread across India & abroad. IETE Chandigarh Centre caters to the states of HP, J&K, Punjab,
Haryana and the Union Territory of Chandigarh.
Government of India, Ministry of Science and Technology, Department of Science and Industrial
Research has recognized IETE as a Scientific and Industrial Research Organisation (SIRO) and the
Institution also has been notified as an Educational Institution of National Eminence by the
Government of India.
The Outline contents of the 6 Weeks training are as follows;
Use of Electronic Instruments, Soldering and Disoldering Practice, Active and passive
component, Study of other components, Orcad, Introduction to Embedded Systems,
Fundamentals of C, 8051 Microcontroller, Embedded hardware and software
interfacing.
Embedded C, Keil uVision, Proteus(ISIS), ORCAD, Fiber Optics Safety, Fiber Optics
DR KAMLESH KUMAR SAINI
(M) 09354441682
SH. RAVI KUMAR DONGAONKAR
(M) 09417196843
Cable and Connector Identification, Tools and equipment
Project selection, Project implementation, PCB Designing, PCB Fabrication, Report
writing
Presentation skills, Visit to Research & Development Laboratories such as CSIO,
TBRL etc.
Visit to Electronics Manufacturing Units such as BEL etc.,
Viva voce
Details of course are attached.
SH. SURENDER SINGH SAINI
(M) 09417162217
CO-OPTED MEMBER
SH. D. P. GOEL
(M) 09463654539
PROF. J. K. CHHABRA
(M) 09888410066
DR RAMA GOPAL V SAREPAKA
(M) 09417655686
DR HARDEEP SINGH RYAIT
(M) 09878003421
Resource faculty for the training is highly experienced in R&D/Industry to impart the training in most
effective way.
i)
Fee: Rs 2500/- per trainee for 6 Weeks for the course --Use of Components for Project
Implementation
Fee: Rs 3500/- per trainee for 6 Weeks for the course –Hardware & Embedded Design
Fee: Rs 4000/- per trainee for 6 Weeks for the course - Fiber Optic Practical course
Fee : Rs 2500/- per trainee for 6 weeks for the course- Industrial training on “SOFT TOOLS”
(10% Fee concession for ISF members)
(M) 09465448600
ii)
iii)
iv)
SH. RAJESH KUMAR
(M) 08427089712
For opening of IETE Students Forum (ISF) at your premises, please feel free to contact undersigned.
DR NEELAM RUP PRAKASH
STUDENT MEMBER
SH. AMAN RANA
(M) 08427481600
Ms CHEENA ROHILLA
(M) 09779388879
There is provision of monitoring of training by the institution faculty/HOD/TPO during the
programme to ascertain the performance of the students.
There are limited intakes in each batch and registration is on the basis of the first come first serve.
You are requested to bring it to the notice of the students for early registration along with the
remittance, to avail of the facilities. For more information, please
free to contact, e-mail or visit the Centre personally.
Six Weeks Industrial / Summer Training
Course Structure (Use of Components for Project Implementation)
For Diploma /B.Tech/B.E Students (Fee Rs 2500/-)
Topics
Use Analog and Digital Multi-meter
Use of Oscilloscope (CRO)
Soldering / De-soldering
Soldering / De-soldering
Components Passive devices
Components Active Devices
Diodes, BJT MOSFET,UJT
Components Active Devices ICs
LSI, VLSI, UP, UC, ASIC
Digital Gates, NAND, NOR, AND, OR
Testing gates OR,NOR, AND,NAND & Flip- Flops
Multivibrator study
OP Amp Study
Wireless Technologies
Basics of PCB Designing & Fabrication
Embedded Technology(ET)
An Overview
Overview of Different Microcontrollers
Study µC (Micro-Controller)
Programming Basics
Visit to CSIO/ISTC
Term Report
Details
Resolution, Accuracy, Precision, R, L, C
Measurement, Voltage Measurement, Current
Measurement, Use of Line Tester, Series Bulb
Tester
Technical Specifications Range, Accuracy Time,
Frequency, Amplitude, Waveform Measurement
Soldering, Cleaning, Wetting, solder Control of Heat
De-Soldering of Joints
R,L,C, Color Coding, Ratings, wattage,
characteristics study
Pin identification, Value, Ratings, Consulting data
sheet, Diodes, Zeners, diodes
Consulting data sheets Identification, PINs Reading
Consulting Data sheets, Identification, PINs Reading
recording
Testing & recording
Assembly
Testing & recording
An overview on different applications of wireless
technologies
An Overview of PCB Designing & Fabrication
An overview on different applications of embedded
technology/systems
Overview of 8-Bit, 16-Bit & 32-Bit Microcontrollers
Consulting Data manual, Recording data Simple
Programs
VISIT to CSIO/ISTC
Term Report
Project Identification by student under guidance
Listing out the parts, components, parts for the
project
Project completion, Test, Report presentation
Project Viva-Voice
Six Weeks Industrial / Summer Training
Course Structure: Hardware & Embedded Design Course
(6 Weeks) (Charges Rs 3500/-)
 Embedded Software





Numbering System ,8051 Assembler & Simulator (1 Lab)
Simulating I/O Ports (1 Lab)
Data Transfer ,Arithmetic & Logical Operations (1 Labs)
Number System Conversion (1 Lab)
Keil µvision IDE, Test programs(2 Lab)
 Embedded Hardware














Testing 8051 I/O Ports (1 Lab)
LED & Switch Interfacing (1 Lab)
Buzzer interfacing with 8051(1 Lab )
Relay interfacing with 8051(1 Lab)
Seven segment interfacing(2 Labs)
Interfacing of LCD with 8051 (2 Lab)
Keypad interfacing with 8051(1 Lab)
Timer Programming (1 Labs)
Counter Programming (1 Labs)
ADC Interfacing with 8051 (2 Lab)
Interfacing a Sensor with 8051 (1 Labs)
Interfacing a DC Motor with 8051 (2 Labs)
Interrupt Programming (2 Labs)
Introduction to advance microcontroller (PIC,AVR,ARM)
 Minor Project (6 Labs)
List of projects:
o
o
o
o
o
o
o
o
o
Bidirectional visitor counter using 8051
Real time clock based digital clock
Electronic voting machine
Smart street light
DC voltmeter
Digital thermometer with temperature control
Electronic code lock using 8051
Water level controller
Line follower robot
Six Weeks Industrial / Summer Training
For Diploma /B.Tech/B.E Students (Fee Rs 2500/-)
Course syllabus of Six weeks Industrial training on “SOFT TOOLS”
1. Embedded C (1/2 week)
 Introduction of programming
 Fundamental of C and Embedded C Programming
 Sample programs
2. Keil uVision (1 week)
 µVision Debugger/ Assembler/ Compiler
 Creating project
 Introduction of various tools, library manager, project ,editor and output windows
 Creating embedded programs
 Creating a Project File Using the Project Windows
 Creating Source Files
 Adding Source Files to the Project and setting Target Options
 Building the Project and creating a HEX File
 Debugging
3. Proteus(ISIS) ( 1 week)
 Virtual System Modelling (VSM)
 Picking animated component from library
 Creating circuit in Editing window and loading hex file
 Circuit simulation with animated components
 Using virtual measurement devices and source
 Microcontroller models to co-simulate the microcontroller based designs
i.
4. ORCAD (2 weeks)
i. Capture
 Designing of schematics.
 Making a Symbol and creating library
 Adding components and libraries
 Editing components
 Creating Netlist
ii. Layout
 PCB designing
 Loading Template file
 Making Footprints 6. Loading the Netlist
 Opening the Netlist in Layout
 Making the Board Outline
 Placing the Board
 Setting up to Route the Board
 Making a Copper Pour
 Routing the Board
5. Project (1 ½ weeks)
Six Weeks Industrial / Summer Training
(Fiber Optic Practical course curriculum)
For Diploma /B.Tech/B.E Students (Fee Rs 4000/-)
S.No.
Topics
Introduction to Fiber Optics
1
2
Fiber To The Home
3
Fiber Optics Safety, Application of Fiber Optics
4
Fiber Optics Cable and Connector Identification
5
Termination of Fiber Connectors, Connectorisation, Polishing, testing of
connectors
6
Introduction to splicing, Mechanical and Fusion
7
Introduction to basic OTDR Functions, Use of the OTDR, Power source and
Light meter Functions
8
Continuity Testing, Tools and equipment
9
Class discussion & Seminar
10
Conclusion
11
Practical or lab or field video after each session
12
Minor Project