Datasheet: PROFIBUS Tester 5 BC-700-PB

Transcription

Datasheet: PROFIBUS Tester 5 BC-700-PB
PROFIBUS Tester 5 BC-700-PB
Quick and Easy Testing of Bus Physics, Bus Communication and Cabling
The PROFIBUS Tester 5 BC-700-PB is a powerful diagnostic and troubleshooting tool for testing the
cables, measuring the signals and analyzing the communication of PROFIBUS networks. It is batterypowered and provides a graphical display, allowing for quick results when working in stand-alone
mode. Optionally, also PROFIBUS PA network can be analyzed. In addition, the BC-700-PB supports
the export of test results for advanced analysis.
PROFIBUS Master
(PLC)
PROFIBUS DP
Field
Device
Field
Device
Segment
Coupler
PROFIBUS Slaves
Field
Device
PROFIBUS PA
Field
Device
PROFIBUS PA Analysis
(Optional)
PROFIBUS
Diagnostics
Software
(Enhanced Diagnostics,
Remote Operation)
PROFIBUS DP Analysis
USB Connections
(Optional)
Test Report
Testing Bus Cabling, Bus Physics and Bus
Communication “All-In-One”
Enhanced Diagnostic Features Through
Complementing PC-Based Software
> Combination of signal tester, storage oscilloscope, protocol
analyzer, master simulator and cable tester functionality in a
single diagnostics tool
> Many additional features for executing, analyzing and
managing bus tests in PC mode (Trend, Topology Scan,
Master Simulator, Oscilloscope, Frame Analyzer)
> Stand-alone mode plus extended PC-based diagnostics
> Quick Test and User-Controlled Test for easy network status
assessment at the push of a button
> Suited for installation, setup and commissioning,
documentation, acceptance testing, network optimization,
preventive maintenance, troubleshooting as well as laboratory
tests
Highly Mobile Bus Tester for Testing Even
Without a Notebook
> Battery-powered operation without the need for additional
power supply
> Graphical display providing easy-to-understand presentation of
test results
> Comprehensive network tests in stand-alone mode without
requiring a notebook
> Generation of test reports describing the actual status of the
PROFIBUS installation
> Ideal for less experienced users as well as for fieldbus
specialists
Optional Measuring Adapter for MBP
(Manchester Coded Bus Powered) Physics
> Specific signal analysis supporting MBP Physics (feeding
voltage, signal deviation, signal polarity, bitrate divergence)
> Complete protocol analysis directly at PROFIBUS PA segment
Technical Data
Diagnostics Functionality
Protocol and Frame Analysis
Signal Analysis ...
... via EIA-485
... via MBP
(requires optional adapter)
PROFIBUS DP-V0 and DP-V1, automatic baud rate detection in the range of 9.6 kbit/s … 12 Mbit/s
PROFIBUS DP-V0, DP-V1, FMS and MPI
Signal quality index: 0 … 5,000, determined from signal level as well as signal/noise ratio and rise time;
signal sampling with 8/16 samples per bit
Fieldbus feeding voltage: 0 V ... 35 V at 0.1 V resolution, signal level: 100 mV ... 1,200 mV at 10 mV resolution,
signal polarity, bitrate divergence: ±1.2 % at 0.01 % resolution, signal sampling with 128 samples per bit
Oscilloscope Display
(Not Available for MBP)
Test range: ±5 V at 10 mV resolution (differential), 0 V … 15 V at 15 mV resolution (A or B to DGND);
sampling rate: up to 384 Msamples/s; sampled points: 2,400 (signal details), 8,192 (oscilloscope analysis)
Topology Scan
(Not Available for MBP)
Active, maximum distance: 230 m, accuracy: ±2 m
Cable Test
(Not Available for MBP)
Active, supported cable segment length: 5 m … 1,500 m, accuracy: 5 %
Operation
Via graphical colour display, four function keys and scrollwheel including central push-button or via PC/notebook
Internal Memory Capacity
3 user-definable network directories (segment and test location) for storing quick tests, trend logs and cable test results
Trend logging: max. 99 hours
Trigger
IN: L = 0 V .. 0.8 V; H = 2.4 V .. 24 V; pulse > 10 μs, active high
OUT: approximately 5 V, active low (connection to storage oscilloscope)
PC Operating Software
PROFIBUS Diagnostics Suite, see separate datasheet for details
Connectors
EIA-485 (PROFIBUS DP)
MBP (PROFIBUS PA)
Technical changes reserved © Softing Industrial Automation GmbH, PROFIBUS_Tester_5_BC-700-PB_D_EN_1504_101, April 2015
USB
PROFIBUS D-sub connector, 9 pins, power supply for external bus termination
Connector, 3 pins, for screw terminals at optinal measuring adapter, measuring cable set including 3 probes
(adapter for MBP measurement is attached to D-sub connector)
V 2.0, high speed 480 Mbit/s, galvanically isolated
Dimensions (H x W x D)
35 mm x 220 mm x 110 mm
Power Supply
Built-in three-cell lithium-ion battery supporting 11.1 VDC or external AC adapter 100 VAC ... 240 VAC, 50/60 Hz (galvanically
isolated)
The rechargeable battery has a runtime of up to 5 hours (runtime depends on the performed test functionality and rate of
wear of the rechargeable battery), battery is charged via external AC adapter
Operating/Storage Temperature
Operating temperature: 0 °C ... 50 °C, storage temperature: -20 °C ... 70 °C
Relative Humidity
Air humidity: 10 % ... 90 % without condensation
Weight
Test tool, no cable: approximately 0.75 kg; complete carrying case: approximately 4.2 kg
Conformity
CE, FCC, VCCI
Scope of Delivery
Hardware
PROFIBUS Tester 5 BC-700-PB, power supply unit 100 VAC ... 240 VAC, 50/60 Hz with connecting cables for Europe and
USA, adaptor cables, carrying case
Measuring adapter BC-700-H1, measuring cable set (for PROFIBUS PA option)
Software
PROFIBUS Diagnostics Suite (PC software for Windows on CD-ROM)
BC-700-PB upgrade license (on CD-ROM, for PROFIBUS PA option)
Documentation
Device manual, “Getting Started“ manual
Order Numbers
DDA-NN-006014
PROFIBUS Tester 5 BC-700-PB
DDL-NL-006010
PROFIBUS PA option for BC-700-PB (BC-700-PB serial number required for order placement)
Additional Products and Services
BC-600-PB-CB-M12
D-Sub to M12 adapter set with T-piece and M12 bus termination for PROFIBUS DP
PB-LSZ-CHB3
Digital fieldbus leakage current clamp for locating EMC problems, 40 Hz ... 1,000 Hz, Min/Max, Data Hold, measuring cables,
supplied in handy case (fits into empty compartment of carrying case)
BC-PBMB-PB-S
D-Sub service interface with active bus termination and 90° angled connector for PROFIBUS DP
BC-M12DP-PB
M12 service interface for PROFIBUS DP, comprising M12 T-piece, end cap, M12 connection cable (1 m)
TRA-PB-TECH
Training „PROFIBUS Technology“, 2 days
TRA-PB-TS
Training „PROFIBUS Troubleshooting“, 3 days
Softing Industrial Automation GmbH
Richard-Reitzner-Allee 6
85540 Haar / Germany
Tel.: +49 89 456 56-340
Fax: +49 89 456 56-488
[email protected]
http://industrial.softing.com
Softing Industrial Automation GmbH
Äußere Sulzbacher Straße 159-161
90491 Nuremberg / Germany
Tel.: +49 911 544 27-0
Fax: +49 911 544 27-27
[email protected]
http://industrial.softing.com
Buxbaum Automation GmbH
Thomas-Alva-Edison-Straße 1
7000 Eisenstadt / Austria
Tel.: +43 2682 704 560
Fax: +43 2682 205 77 00-5610
[email protected]
http://myautomation.at
Softing North America Inc.
US Headquarter
7209 Chapman Highway
Knoxville, TN 37920 / USA
Tel.: +1 865 251 52 52
Fax: +1 865 579 47 40
[email protected]
http://softing.us
Softing North America Inc.
US Sales Office
29 Water Street, Suite 301
Newburyport, MA 01950 / USA
Tel.: +1 978 499 96 50
Fax: +1 978 499 96 54
[email protected]
http://softing.us
Softing Italia Srl
Via Padre Massimiliano Kolbe, 6
20090 Cesano Boscone (MI) / Italy
Tel.: +39 02 450 51 71
Fax: +39 02 450 41 41
[email protected]
http://softingitalia.it
Your local Softing Contact: