IP CODE REPORT

Transcription

IP CODE REPORT

Shenzhen BST Technology Co., Ltd.
Report No.: BST10014222728R-8
IP CODE REPORT
Prepared For :
Product Name:
LEDA SERIES LED LIGHTING
Trade Name:
Model :
LEDA-F502D, LEDA-F502(A, B ,C), LEDA-F503(A, B, C, D, E)
Prepared By :
3F,Weames Technology Building,No. 10 Kefa Road,
Science Park,Nanshan District,Shenzhen,Guangdong,China
Test Date:
Jan. 27-28, 2010
Date of Report :
Jan. 28, 2010
Report No.:
BST10014222728R-8
3F,Weames Technology Building, No. 10 Kefa Road, Science Park, Nanshan District, Shenzhen, Guangdong, China
Tel:86-755- 26747751~3（100 lines） Fax:86-755-26504032 http://www.bst-lab.com
Page 1 of 10
IP CODE Report
EN60529
Degrees of protection
provided by enclosures
Shenzhen BST Technology Co.,Ltd.
Address ……………………………….. :
Testing location …………………….. : Shenzhen BST Technology Co.,Ltd.
Applicant ……………………………… :
Address ……………………………….. :
Address ……………………………….. :
Standard ………………………………. : EN 60529: 1991/A1:2000
Test Result ……………………………. : Compliance with
EN 60529: 1991/A1:2000
Procedure deviation ………………… : N.A.
Non-standard test method ………… : N.A.
Type of test object ………………….. : LEDA SERIES LED LIGHTING
Trademark ……………………………. :
Model/type reference ……………….. : LEDA-F502D, LEDA-F502(A, B ,C), LEDA-F503(A, B, C, D, E)
Rating …………………………………. : IP CODE
IP65
3F,Weames Technology Building, No. 10 Kefa Road, Science Park, Nanshan District, Shenzhen, Guangdong, China
Page 2 of 10
Possible test case verdicts :
test case does not apply to the test object …….. : N(.A.)
test object does meet the requirement …….…… : P(ass)
test object does not meet the requirement …….
: F(ail)
Name and address of the testing laboratory : Shenzhen BST Technology Co.,Ltd.
3F,Weames Technology Building,No. 10 Kefa Road,
Test
by :
Signature
Date
Technician
Title
Review by
:
Signature
Date
Project Engineer
Title
Approved by:
Signature
Date
Christina/ Manager
Name and Title
3F,Weames Technology Building, No. 10 Kefa Road, Science Park, Nanshan District, Shenzhen, Guangdong,
China
Page 3 of 10
Verändert mit der DEMOVERSION von CAD-KAS PDF Passwort Knacker (http://www.cadkas.de).
General remarks:
"(see remark #)" refers to a remark appended to the
report.
Attached with:
the report.
Throughout this report a comma is used as the
decimal separator.
The test results presented in this report relate only to
the object tested.
This report shall not be reproduced except in full
without the written approval of the testing laboratory.
China
Page 4 of 10
EN 60529
Clause
Requirement - Test
5
Degrees of protection against access to hazardous parts and against solid
foreign objects indicated by the first characteristic numeral
Protection against access to hazardous parts
5.1
5.2
Result - Remark
Protected against access to hazardous parts with
a wire
The access probe of 1,0 mm 0 shall not
penetrate
Protection against access solid foreign
objects
First characteristic numeral is 6
Verdict
P
P
P
P
Dust-tight
No ingress of dust
6
10
Degrees of protection against ingress of water indicated by the second
characteristic numeral
Second
characteristic numeral is 5
Protected against water jets
Water projected in jets against the
enclosure from any direction shall have
no harmful effects
P
Marking
The requirements for marking shall be specified in
the relevant product standard.
P
P
P
when
- one part of an enclosure has a different degree
of protection to that of another part of the same
enclosure;
- the mounting position has an influence on the
degree of protection;
-the maximum immersion depth and time are
indicated.
11
11.1
General requirements for tests
Atmospheric conditions for water or dust
Tests:
Temperature range:
Relative humidity: 25% to 75%
Air pressure:
15 "C to 35 "C
86 kPa to 106 kPa
P
P
China
Page 5 of 10
EN 60529
Clause
Requirement - Test
11.2
(860 mbar to 1 060 mbar).
Test samples
The tests specified in this standard are type tests.
12.1
12.2
12.3
13
13.1&
13.2
13.3
Result - Remark
first characteristic numeral
Access probes
The test wire of 1,0 mm 0 shall not penetrate and
adequate clearance shall be kept
Test conditions
For tests on low-voltage equipment, a low-voltage
supply (of not less than 40 V and not more
than 50 V) in series with a suitable lamp should be
CONNECTORed between the probe and the
hazardous
parts inside the enclosure. Hazardous live parts
covered only with varnish or paint, or protected by
oxidation or by a similar process, are covered by a
metal foil electrically CONNECTORed to those
parts which are normally live in operation.
The signal-circuit method should also be applied
to the hazardous moving parts of high-voltage
equipment. Internal moving parts may be
operated slowly, where this is possible.
Acceptance conditions
:The protection is satisfactory if adequate
Tests for protection against solid foreign objects indicated by the first
characteristic numeral
Test means & Test conditions
Test means and the main test conditions are
given
in Table VII
Acceptance conditions for first
characteristic numerals 1,2,3,4
The protection is satisfactory if the full diameter of
the probe specified in Table VII does not pass
through any opening.
Verdict
P
P
P
P
P
P
P
China
Page 6 of 10
EN 60529
Clause
Requirement - Test
14
Tests for protection against water
indicated by the second characteristic
numeral
Result - Remark
Verdict
P
given
in Table VIII
14.2.5
Test for second characteristic numeral 5
with the 6,3 mm nozzle
P
14.3
Acceptance conditions
After testing in accordance with the appropriate
requirements of 14.2.1 to 14.2.8 the enclosure
shall
be inspected for ingress of water.
It is the responsibility of the relevant Technical
Committee to specify the amount of water which
may be allowed to enter the enclosure and the
details of a dielectric strength test, if any.
In general, if any water has entered, it shall not:
-be sufficient to interfere with the correct
operation of the equipment or impair safety;
- deposit on insulation parts where it could lead
to tracking along the creepage distances;
- reach live parts or windings not designed to
operate when wet;
- accumulate near the cable end or enter the
cable if any.
If the enclosure is provided with drain-holes, it
should be proved by inspection that any water
P
away
without doing any harm to the equipment.
For enclosures without drain-holes, the relevant
product standard shall specify the acceptance
conditions if water can accumulate to reach live
parts.
China
Page 7 of 10
EN 60529
Clause
Requirement - Test
Result - Remark
Verdict
China
Page 8 of 10
Photo:
Figure 1
General Appearance of the EUT
Figure 2
General Appearance of the EUT
China
Page 9 of 10
China
Page 10 of 10

IP CODE REPORT

Transcription

Similar documents

Shenzhen Fiyta Holdings Ltd

FIYTA Holdings Ltd

LED Wall Washer Light Products Specification Feature

How to use DNSdynamic for remote access? .

First announcement and call for abstracts ICDCS - Purdue e-Pubs

10:00 11:00 - MOD Institute

How to fix the audio noise issue

Fiyta Extreme 3D - Red Army Watches

Credit China Issues HK$300 Million Convertible Bonds and Forms

resume - Lisa Du