SECTION 10520 FIRE PROTECTION SPECIALTIES PART 1

Transcription

SECTION 10520 FIRE PROTECTION SPECIALTIES PART 1
SECTION 10520
FIRE PROTECTION SPECIALTIES
PART 1 - GENERAL
1.1
A.
SUMMARY
This Section includes the following:
1.
2.
3.
1.2
A.
Portable fire extinguishers.
Cabinet mounted fire extinguishers.
Mounting brackets for fire extinguishers.
SUBMITTALS
Product Data: For each type of product indicated.
1.
2.
3.
Fire Extinguishers: Include rating and classification.
Fire-Protection Cabinets: Include door hardware, cabinet type, trim style,
panel style, and details of installation.
Show location of knockouts for hose valves.
B.
Samples: For each exposed cabinet finish.
C.
Maintenance data.
1.3
QUALITY ASSURANCE
A.
NFPA Compliance: Fabricate and label fire extinguishers to comply with NFPA 10,
"Portable Fire Extinguishers."
B.
Fire Extinguishers: Listed and labeled for type, rating, and classification by an
independent testing agency acceptable to authorities having jurisdiction.
C.
Fire-Rated Fire-Protection Cabinets: Listed and labeled to comply with requirements of
ASTM E 814 for fire-resistance rating of walls where they are installed.
1.4
COORDINATION
A.
Coordinate size of fire-protection cabinets to ensure that type and capacity of fire
extinguishers indicated are accommodated.
B.
Apply decals on field-painted fire-protection cabinets after painting is complete.
Value Place Hotel, Humble, TX
BRR No. 31000019
March 18, 2015
FIRE PROTECTION SPECIALTIES
10520 - 1
1.5
A.
WARRANTY
Special Warranty: Manufacturer's standard form in which manufacturer agrees to
repair or replace components of portable fire extinguishers that fail in materials or
workmanship within specified warranty period.
1.
Failures include, but are not limited to, the following:
a.
b.
2.
Failure of hydrostatic test according to NFPA 10.
Faulty operation of valves or release levers.
Warranty Period: Six years from date of Substantial Completion.
PART 2 - PRODUCTS
2.1
A.
MANUFACTURERS
In other Part 2 articles where titles below introduce lists, the following requirements
apply to product selection:
1.
2.2
A.
PORTABLE FIRE EXTINGUISHERS
Available Manufacturers:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
B.
Basis-of-Design Product: The design for each product is based on the
product named. Subject to compliance with requirements, provide either
the named product or a comparable product by one of the other
manufacturers specified.
Amerex Corporation.
Ansul Incorporated.
Badger Fire Protection.
Buckeye Fire Equipment Company.
Fire End & Croker Corporation.
General Fire Extinguisher Corporation.
JL Industries, Inc.
Kidde Fyrnetics.
Larsen's Manufacturing Company.
Modern Metal Products; Div. of Technico.
Moon American.
Potter Roemer; Div. of Smith Industries, Inc.
Watrous; Div. of American Specialties, Inc.
General: Provide fire extinguishers of type, size, and capacity for each fire-protection
cabinet and mounting bracket indicated.
1.
Instruction Labels: Include pictorial marking system complying with
NFPA 10, Appendix B.
Value Place Hotel, Humble, TX
BRR No. 31000019
March 18, 2015
FIRE PROTECTION SPECIALTIES
10520 - 2
C.
2.3
Multipurpose Dry-Chemical Type in Steel Container: UL-rated -A:B:C, 10-lb nominal
capacity, with monoammonium phosphate-based dry chemical in enameled-steel
container.
FIRE-PROTECTION CABINET
A.
Basis-of-Design Product: J.L Industries (Model #1827FX) or a comparable product by
one of the following:
B.
Available Manufacturers:
1.
2.
3.
4.
5.
6.
7.
8.
9.
Fire End & Croker Corporation.
General Accessory Mfg. Co.
JL Industries, Inc.
Kidde Fyrnetics.
Larsen's Manufacturing Company.
Modern Metal Products; Div. of Technico.
Moon American.
Potter Roemer; Div. of Smith Industries, Inc.
Watrous; Div. of American Specialties, Inc.
C.
Cabinet Type: Suitable for fire extinguisher.
D.
Cabinet Construction: Nonrated.
E.
Cabinet Material: Enameled-steel or Aluminum or Stainless-steel sheet.
F.
Semirecessed Cabinet: Cabinet box partially recessed in walls of shallow depth to suit
style of trim indicated; with one-piece combination trim and perimeter door frame
overlapping surrounding wall surface with exposed trim face and wall return at outer
edge (backbend).
1.
Trim: One-piece combination trim and perimeter door frame overlapping
surrounding wall surface, rounded edge trim with 2-1/2” backband.
G.
Cabinet Trim Material: Aluminum sheet.
H.
Door Material: Aluminum sheet.
I.
Door Style: Double strength full glass.
J.
Door Glazing: Tempered float glass (clear) Tempered float glass.
K.
Door Hardware: Manufacturer's standard door-operating hardware of proper type for
cabinet type, trim style, and door material and style indicated.
L.
Accessories:
1.
Mounting Bracket: Manufacturer's standard steel, designed to secure fire
extinguisher to fire-protection cabinet, with plated or baked-enamel finish.
Value Place Hotel, Humble, TX
BRR No. 31000019
March 18, 2015
FIRE PROTECTION SPECIALTIES
10520 - 3
M.
Finishes:
1.
2.4
A.
MOUNTING BRACKETS
Available Manufacturers:
1.
2.
3.
4.
5.
6.
7.
8.
9.
B.
Amerex Corporation.
Ansul Incorporated.
Badger Fire Protection.
Buckeye Fire Equipment Company.
Fire End & Croker Corporation.
General Fire Extinguisher Corporation.
JL Industries, Inc.
Larsen's Manufacturing Company.
Potter Roemer; Div. of Smith Industries, Inc.
Mounting Brackets: Manufacturer's standard galvanized steel, designed to secure fire
extinguisher to wall or structure, of sizes required for types and capacities of fire
extinguishers indicated, with plated or baked-enamel finish.
1.
C.
Aluminum: Class I, clear anodic coating complying with AAMA 611.
Color: Red.
Identification: Lettering complying with authorities having jurisdiction for letter style,
size, spacing, and location. Locate as indicated by Architect.
1.
Identify bracket-mounted fire extinguishers with the words "FIRE
EXTINGUISHER" in red letter decals applied to mounting surface.
a.
2.5
A.
FABRICATION
Fire-Protection Cabinets: Provide manufacturer's standard box (tub), with trim, frame,
door, and hardware to suit cabinet type, trim style, and door style indicated. Weld
joints and grind smooth.
1.
B.
Orientation: Vertical.
Construct fire-rated cabinets with double walls fabricated from 0.0428inch- thick, cold-rolled steel sheet lined with minimum 5/8-inch- thick, firebarrier material. Provide factory-drilled mounting holes.
Cabinet Doors: Fabricate doors according to manufacturer's standards, from materials
indicated and coordinated with cabinet types and trim styles selected.
1.
2.
Fabricate door frames with tubular stiles and rails and hollow-metal
design, minimum 1/2 inch thick.
Miter and weld perimeter door frames.
Value Place Hotel, Humble, TX
BRR No. 31000019
March 18, 2015
FIRE PROTECTION SPECIALTIES
10520 - 4
C.
Cabinet Trim: Fabricate cabinet trim in one piece with corners mitered, welded, and
ground smooth.
PART 3 - EXECUTION
3.1
INSTALLATION
A.
Examine walls and partitions for suitable framing depth and blocking where semi
recessed cabinets will be installed.
B.
Examine fire extinguishers for proper charging and tagging. Remove and replace
damaged, defective, or undercharged units.
C.
Prepare recesses for semi recessed fire-protection cabinets as required by type and
size of cabinet and trim style.
D.
Install fire-protection specialties in locations and at mounting heights indicated or, if not
indicated, at heights acceptable to authorities having jurisdiction.
E.
Fire-Protection Cabinets: Fasten fire-protection cabinets to structure, square and
plumb.
1.
2.
3.
Unless otherwise indicated, provide recessed fire-protection cabinets. If
wall thickness is not adequate for recessed cabinets, provide semi
recessed fire-protection cabinets.
Provide inside latch and lock for break-glass panels.
Fasten mounting brackets to inside surface of fire-protection cabinets,
square and plumb.
F.
Mounting Brackets: Fasten mounting brackets to surfaces, square and plumb, at
locations indicated.
G.
Identification: Apply decals at locations indicated.
H.
Adjust fire-protection cabinet doors to operate easily without binding. Verify that
integral locking devices operate properly.
I.
Replace fire-protection cabinets that have been damaged or have deteriorated beyond
successful repair.
END OF SECTION
Value Place Hotel, Humble, TX
BRR No. 31000019
March 18, 2015
FIRE PROTECTION SPECIALTIES
10520 - 5
SECTION 10801
TOILET AND BATH ACCESSORIES
PART 1 - GENERAL
1.1
A.
SUMMARY
This Section includes the following:
1.
2.
3.
4.
1.2
Public-use washroom accessories.
Private-use bathroom accessories.
Underlavatory guards.
Custodial accessories.
SUBMITTALS
A.
Product Data: For each type of product indicated.
B.
Product Schedule:
1. Identify locations using room designations indicated on Drawings.
2. Identify products using designations indicated on Drawings.
PART 2 - PRODUCTS
2.1
SCHEDULE OF ACCESSORIES
A.
See Suggested Vendors List in Division 01100, Interior Materials Lists on Drawings,
and Basis of Design items at the end of this Section.
B.
Available Manufacturers: Subject to compliance with requirements, manufacturers
offering products that may be incorporated into the Work include, but are not limited to,
the following:
1.
2.
3.
4.
2.2
A.
American Specialties, Inc.
Bobrick Washroom Equipment, Inc.
Bradley Corporation.
General Accessory Manufacturing Co. (GAMCO).
UNDERLAVATORY GUARDS
Available Manufacturers: Subject to compliance with requirements, manufacturers
offering products that may be incorporated into the Work include, but are not limited to,
the following:
Value Place Hotel, Humble, TX
BRR No. 31000019
March 18, 2015
TOILET AND BATH ACCESSORIES
10801 - 1
1. Plumberex Specialty Products, Inc.
2. TCI Products.
3. Truebro, Inc.
B.
Underlavatory Guard:
1. Description: Insulating pipe covering for supply and drain piping assemblies
that prevent direct contact with and burns from piping, and allow service
access without removing coverings.
2. Material and Finish: Antimicrobial, molded-plastic, white.
2.3
A.
CUSTODIAL ACCESSORIES
Available Manufacturers: Subject to compliance with requirements, manufacturers
offering products that may be incorporated into the Work include, but are not limited to,
the following:
1.
2.
3.
4.
5.
2.4
A.
A & J Washroom Accessories, Inc.
American Specialties, Inc.
Bobrick Washroom Equipment, Inc.
Bradley Corporation.
General Accessory Manufacturing Co. (GAMCO).
FABRICATION
Keys: Provide universal keys for internal access to accessories for servicing and
resupplying. Provide minimum of six keys to Owner's representative.
PART 3 - EXECUTION
3.1
A.
INSTALLATION
Install accessories according to manufacturers' written instructions, using fasteners
appropriate to substrate indicated and recommended by unit manufacturer. Install
units level, plumb, and firmly anchored in locations and at heights indicated.
Value Place Hotel, Humble, TX
BRR No. 31000019
March 18, 2015
TOILET AND BATH ACCESSORIES
10801 - 2
BASIS OF DESIGN - Toilet and Bath Accessories
TA-6
TA-6A
TA-7A
TA-7B
TA-8
TA-9
TA-10
TA-10A
TA-11
TA-12
TA-13
24" Grab Bar
12" Grab Bar
36" Grab Bar
18" & 42" Grab Bar
L-Shaped Grab Bar
Folding Shower Seat
30x36 Channel Frame Mirror
24x36 Channel Frame Mirror
Removable Shower Seat
Paper Towel Dispenser
Double Towel Hook
Bradley
Bradley
Bradley
Bradley
Bradley
Bradley
8120-001240
8120-001120
8120-001360
8120-001420
8120-0591836
9569-000000
Franklin Brass
DF596
Ref Drawings
Ref Drawings
Taymor - Sunglow Col. 01-9402
END OF SECTION
Value Place Hotel, Humble, TX
BRR No. 31000019
March 18, 2015
TOILET AND BATH ACCESSORIES
10801 - 3