Temperature Difference Controller TDC 3

Transcription

Installation and operating instructions
TDC 3
Temperature-Difference-Controller
Read carefully before installation, commissioning and operation
Content
A.1
A.2
A.3
A.4
A.5
EC declaration of conformity
General instructions
Explanation of symbols
Changes to the unit
Warranty and liability
3
3
3
4
4
B.1
B.2
B.3
B.4
B.5
Specifications
About the controller
Scope of supply
Disposal and pollutants
Hydraulic variants
5
6
6
6
7
C.1
C.2
C.3
Wall installation
Electrical connection
Installing the temperature sensors
8
9
10
D
Terminal connection diagrams
11
E.1
E.2
E.3
E.4
Display and input
Commissioning help
Free commissioning
Menu sequence and menu structure
22
23
23
24
1.
Measurement values
25
2.
2.1
2.2
2.3
2.4
2.5
2.6
Statistics
Operating hours
Average temperature difference ∆T
Heat output
Graphic overview
Message log
Reset/clear
26
26
26
26
26
26
26
3.
3.1
3.2
3.3
Display mode
Schematic
Overview
Alternating
27
27
27
27
4.
4.1
4.2
4.3
4.4
Operating modes
Automatic
Manual
Off
Fill system
28
28
28
28
28
5.
Settings
29
5.1 Tmin S1
29
5.2 Tmin S2
29
5.3 Tmin S3
29
5.4 Tmax S2
30
5.5 Tmax S3
30
5.6 ∆T R1
30
5.7 ∆T R2
31
5.8 Tset S3
31
5.9 Hysteresis
31
5.10 Priority sensor
32
5.11 T priority
32
5.12 Loading time
32
5.13 Increase
32
5.14 Thermostat periods
32
5.15 „Party Function“
33
5.16 Energy saving mode
33
5.17 TecoS3
33
5.18 Table: Programs (hydraulic variants) with associated settings
34
6.
6.1
6.2
6.3
6.4
6.4.1
6.5
6.6
6.7
Protective functions
Seizing protection
Frost protection
System protection
Collector protection
Cooling functions
Col.- Alarm
Recooling
Anti-Legionella
35
35
35
36
36
37
37
37
38
7.
7.1
7.2
7.3
7.4
7.5
7.6
7.7
7.8
7.9
7.9.1
7.9.2
7.9.3
7.9.4
7.9.5
7.9.6
Special functions
Program selections
Time & date
Sensor calibration
Commissioning
Factory settings
Expansions
Heat quantity
Start aid function
Speed control
Variant
Purging time
Sweep time
Max. speed
Min. speed
Setpoint
39
39
39
39
40
40
40
40
41
42
42
43
43
43
43
43
8.
Menu lock
44
10.
Language
44
9.
Service values
45
Z.1.
Z.2
Z.3
Malfunctions with error messages
Replacing the fuse
Maintenance
46
47
47
Safety instructions
A.1
EC declaration of conformity
By affixing the CE mark to the unit the manufacturer declares that the TemperatureDifference-Controller 3, hereinafter refererred to as TDC 3 , conforms to the following
relevant safety regulations:
EC low voltage directive
73/23/EEC, as amended by 93/68/EEC
EC electromagnetic compatibility directive
89/336/EEC version 92/31/EEC version 93/68/EEC
Conformity has been verified and the corresponding documentation and the EC declaration of conformity are kept on file by the manufacturer.
A.2
General instructions
It is essential that you read this!
These installation and operating instructions contain basic instructions and important
information regarding safety, installation, commissioning, maintenance and the optimal
use of the unit. Therefore these instructions must be read completely and understood
by the installation technician/specialist and by the system user before installation, commissioning and operation of the unit.
The valid accident prevention regulations, VDE regulations, the regulations of the local power utility, the applicable DIN-EN standards and the installation and operating
instruction of the additional system components must also be observed. The controller
does not under any circumstances replace any safety devices to be provided by the
customer!
Installation, electrical connection, commissioning and maintenance of the unit may
only be carried out by specialists who possess the appropriate training.
For the user: Make sure that the specialist gives you detailed information on the function and operation of the controller. Always keep these instructions in the vicinity of the
controller.
A.3
Explanation of symbols
Danger
Failure to observe these instructions can result in danger to life from
electric voltage.
Danger
Failure to observe these instructions can result in serious damage to
health such as scalding, or even life-threatening injuries.
Caution
Caution
Failure to observe these instructions can result in destruction of the unit
or the system, or damage to the environment.
Information which is especially important for the function and optimal
use of the unit and the system.
3
Safety instructions
A.4
Changes to the unit
Danger
-
A.5
Changes to the unit can compromise the safety and function of the unit
or the entire system.
Changes, additions to or conversion of the unit are not permitted without the written permission from the manufacturer
It is likewise forbidden to install additional components that have not been tested
together with the unit
If it becomes clear that safe operation of the unit is no longer possible, for example because of damage to the housing, then turn the controller off immediately
Any parts of the unit or accessories that are not in perfect condition must be
exchanged immediately
Use only original spare parts and accessories from the manufacturer.
Markings made on the unit at the factory must not be altered, removed or made
illegible
Only the settings actually described in these instructions may be made on the
controller
Warranty and liability
The controller has been manufactured and tested with regard to high quality and
safety requirements. The unit is subject to the statutory guarantee period of two years
from the date of sale.
The warranty and liability shall not include, however, any injury to persons or material
damage that is attributable to one or more of the following causes:
-
4
Failure to observe these installation and operating instructions
Improper installation, commissioning, maintenance and operation
Improperly executed repairs
Unauthorised structural changes to the unit
Installation of additional components that have not been tested
together with the unit
Any damage resulting from continued use of the unit despite an
obvious defect
Failure to use original spare parts and accessories
Use of the device for other than its intended purpose
Operation above or below the limit values listed in the
specifications
Force majeure
Description of controller
B.1
Specifications
Electrical specifications:
Mains voltage
Mains frequency
Power consumption
Switched power
Electronic relay R1
Mechanical relay R2
Internal fuse
Protection category
Protection class
Sensor inputs
Measuring range
230VAC +/- 10%
50...60Hz
2VA
min.20W...max.120W for AC3
460VA for AC1 / 185W for AC3
2A slow-blow 250V
IP40
II
3 x Pt1000
-40°C up to 300°C
Permissible ambient conditions:
Ambient temperature
for controller operation
0°C...40°C
for transport/storage
0°C...60°C
Air humidity
for controller operation
max. 85% rel. humidity at 25°C
for transport/storage
no moisture condensation permitted
Other specifications and dimensions
Housing design
2-part, ABS plastic
Installation methods
Wall installation, optionally panel installation
Overall dimensions
163mm x 110mm x 52mm
Aperture installation
dimensions
157mm x 106mm x 31mm
Display
Fully graphical display, 128 x 64 dots
Light diode
Multicolour
Operation
4 entry keys
Temperature sensors:
Collector or boiler sensor
Storage tank sensor
Pipe-mounted sensor
Sensor leads
(may not be included in the scope of supply)
Pt1000, e.g. immersion sensor TT/S2 up to 180°C
Pt1000, e.g. immersion sensor TT/P4 up to 95°C
Pt1000, e.g. pipe-mounted sensor TR/P4 up to 95°C
2x0.75mm² extendable up to 30m max.
Temperature resistance table for Pt1000 sensors
°C
Ω
0
10
20
30
40
50
60
70
80
90
100
1000 1039 1077 1116 1155 1194 1232 1270 1308 1347 1385
5
B.2
About the controller
The Temperature Difference Controller TDC 3 facilitates efficient use and function
control of your solar or heating system. The device is impressive most of all for its
functionality and simple, almost self-explanatory operation. For each step in the input
process the individual entry keys are assigned to appropriate functions and explained.
The controller menu contains headwords for the measured values and settings, as well
as help texts or clearly-structured graphics.
The TDC 3 can be used as a temperature difference controller for the various system
variants illustrated and explained under B.5.
Important characteristics of the TDC 3:
Depiction of graphics and texts in a lighted display
Simple viewing of the current measurement values
Analysis and monitoring of the system by means of statistical graphics,etc.
Extensive setting menus with explanations
Menu block can be activated to prevent unintentional setting changes
Resetting to factory settings
A wide range of additional functions are available.
B.3
Scope of supply
3 screws 3,5x35mm and 3 plugs 6mm for wall installation
6 strain relief clips with 12 screws, replacement fuse 2A slow-blow
Installation and operating instructions TDC 3
Optionally contained depending on design/order:
2-3 PT1000 temperature sensors and immersion sleeves
Additionally available:
Pt1000 temperature sensor, immersion sleeves, overvoltage protection,
Various additional functions by means of supplementary circuit boards
B.4
Disposal and pollutants
The unit conforms to the European RoHS directive 2002/95/EC for the restriction of
the use of certain hazardous substances in electrical and electronic equipment.
Caution
6
The unit must not under any circumstances be disposed of with ordinary
household refuse. Dispose of the unit only at appropriate collection
points or ship it back to the seller or manufacturer.
B.5
Hydraulic variants
Caution
1
The following illustrations should be viewed only as schematic diagrams showing the respective hydraulic systems, and do not claim to
be complete. The controller does not replace safety devices under any
circumstances. Depending on the specific application, additional system
components and safety components may be mandatory, such as check
valves, non-return valves, safety temperature limiters, scalding protectors, etc., and must therefore be provided.
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
(T
T
21
(2xT
2xT
7
Installation
C.1
Caution
C.1.1
Wall installation
Install the controller only in dry areas and under the ambient conditions described under B.1 “Specifications”. Carry out the following steps 1-8.
1. Unscrew cover screw completely
2. Carefully pull upper part of housing
from lower part.
3. Set upper part of housing aside, being
sure not to touch the electronics when
doing so.
C.1.2
4. Hold the lower part of the housing up
to the selected position and mark the 3
mounting holes. Make sure that the wall
surface is as even as possible so that the
housing does not become distorted when
it is screwed on.
5. Using a drill and size 6 bit, drill 3 holes
at the points marked on the wall and push
in the plugs.
6. Insert the upper screw and screw it in
slightly.
7. Fit the upper part of the housing and
insert the other two screws.
8. Align the housing and tighten the three
screws.
8
Installation
C.2
Electrical connection
Danger
Caution
Before working on the unit, switch off the power supply and secure it
against being switched on again! Check for the absence of power!
Electrical connections may only be made by a specialist and in compliance with the applicable regulations.
Do not use the controller if the housing shows visible damage.
Low-voltage cables such as temperature sensor cables must be routed
separately from mains voltage cables. Feed temperature sensor cables
only into the left-hand side of the unit, and mains voltage cables only
into the right-hand side.
Caution
The customer must provide an all-pole disconnecting device, e.g. a
heating emergency switch.
Caution
The cables being connected to the unit must not be stripped by more
than 55mm, and the cable jacket must reach into the housing just to the
other side of the strain relief.
Caution
Caution
Relay R1 is only suitable for standard pumps (20-120VA) which are
speed-controlled viathe controller. The internal wiring of the controller
is such that residual currents flow over relay R1 even in the rest condition. Therefore under no circumstances may valves, contactors or other
consumers with low power consumption be operated on this output.
With hydraulic variant D1 „Solar+storage“ relays R1 and R2 are switched on simultaneously to allow the connection of another load at R2.
9
Installation
C.2.1
1.Select necessary program/hydraulics
(Fig. B5 resp. D.1 - D.20)
2.Open controller as described under C.1.
3.Strip cables by 55mmmax., insert, fit the
strain relief devices, strip the last 8-9mm
of the wires (Fig. C.2.1)
4.Open the terminals using a suitable
screwdriver (Fig. C.2.1) and make electrical connections on the controller (s. D.1
- D.20)
5.Refit upper part of housing and fasten
with screw.
6.Switch on mains voltage and place controller in operation.
C.3
Installing the temperature sensors
The controller operates with Pt1000 temperature sensors which are accurate to the
degree, thus ensuring optimal control of system functions.
Caution
Caution
10
If desired the sensor cables can be extended to a maximum of 30m using a cable with a cross-section of at least 0.75mm². Make sure that there is no contact
resistance!
Position the sensor precisely in the area to be measured!
Only use immersion, pipe-mounted or flat-mounted sensor suitable for the specific area of application with the appropriate permissible temperature range.
The temperature sensor cables must be routed separately from mains voltage
cables, and must not, for example, be routed in the same cable duct!
Installation
D
D.1
Caution
Terminal connection diagrams
Solar with storage tank
Sensor side
Mains side
max. 12V
2
Danger230VAC
Relay R1 and R2 are both switched on in
this variant, so e.g. a pump can be connected to R2.
Caution
D.2
Caution
Relay R1: For speed control of
standard pumps, minimum load
20VA
Low voltage max. 12VAC/DC connection
in the left-hand terminal compartment!
Terminal: Connection for:
S1 (2x)
Sensor 1 collector
S2 (2x)
Sensor 2 storage tank
S3 (2x)
Sensor 3 (optional)
The polarity of the sensors is freely selectable.
Mains voltages 230VAC 50-60Hz Connection in the right-hand terminal compartment!
L
Mains phase conductor L
N
Mains neutral conductor N
R1
Pump L (speed)
N
Pump N
R2
Pump L (no speed)
N
Pump N
The PE protective conductor must be connected to the PE metal terminal block!
Solar + Thermostat
Sensor side
max. 12V
Mains side
2
Danger230VAC
20VA
S1 (2x)
Sensor 1 collector
S2 (2x)
Sensor 2 storage tank low
S3 (2x)
Sensor 3 storage tank top
L
N
R1
Pump L (speed)
N
Pump N
R2
Thermostat function L
N
Thermostat function N
The PE protective conductor must be connected to the PE metal terminal block!
11
Installation
D.3
Caution
Solar with bypass
Sensor side
Mains side
max. 12V
2
Danger230VAC
Actuating direction of valve:
R2 on/valve on = bypass without storage
tank charging
Caution
D.4
Caution
20VA
Solar with return lift
Sensor side
max. 12V
Mains side
2
Danger230VAC
R2 on/valve on = path through the storage
tank
20VA
12
S1 (2x)
Sensor 1 collector
S2 (2x)
S3 (2x)
Sensor 3 forward flow
L
N
R1
Pump L (speed)
N
Pump N
R2
Phase valve L
N
Bypass valve N
The PE protective conductor must be
connected to the PE metal terminal block!
S1 (2x)
Sensor 1 collector
S2 (2x)
S3 (2x)
Sensor 3 heating circuit return
L
N
R1
Pump L (speed)
N
Pump N
R2
Valve L
N
Valve N
Installation
D.5
Solar with 2 zone storage tanks
Sensor side
Mains side
max. 12V
2
Danger230VAC
Caution
S1 (2x)
Sensor 1 collector
S2 (2x)
S3 (2x)
L
N
R2 on/valve on = charge to sensor 3
R1
Pump L (speed)
(storage tank above)
N
Pump N
R2
Zone valve L
N
Zone valve N
Caution
20VA
D.6
Caution
Solar with ext. heat exchanger
Sensor side
max. 12V
Mains side
2
Danger230VAC
20VA
S1 (2x)
Sensor 1 collector
S2 (2x)
S3 (2x)
L
N
R1
Pump, secondary L (speed)
N
Pump, secondary N
R2
Pump, primary L
N
Pump, primary N
13
Installation
D.7
Caution
Solar 2 coll. (east/west)
Sensor side
Mains side
max. 12V
2
Danger230VAC
R2 on/valve on = collector with flow through
sensor 3
Caution
D.8
Caution
20VA
Solar 2 coll. 2 pumps
Sensor side
max. 12V
Mains side
2
Danger230VAC
20VA
14
S1 (2x)
Sensor 1 collector 1
S2 (2x)
S3 (2x)
L
N
R1
Pump L (speed)
N
Pump N
R2
Change-over valve L
N
Change-over valve N
S1 (2x)
S2 (2x)
S3 (2x)
L
N
R1
Pump (coll. 1) L (speed)
N
Pump (coll. 1) N
R2
Pump (coll. 2) L
N
Pump (coll. 2) N
Installation
D.9
Caution
Solar 2 Storage tank/valve
Sensor side
Mains side
max. 12V
2
Danger230VAC
(storage tank 2)
Caution
D.10
Caution
20VA
S1 (2x)
Sensor 1 collector
S2 (2x)
Sensor 2 storage tank 1
S3 (2x)
L
N
R1
Pump L (speed)
N
Pump N
R2
Change-over valve L
N
Change-over valve N
Solar 2 storage tank/2 pu.
Sensor side
max. 12V
Mains side
2
Danger230VAC
20VA
S1 (2x)
Sensor 1 collector
S2 (2x)
S3 (2x)
L
N
R1
Pump (St.1) L (speed)
N
Pump (storage tank 1) N
R2
Pump (storage tank 2) L
N
15
Installation
D.11
Solar with follow-on storage tank/Solar & transfer“
Sensor side
Mains side
max. 12V
2
Danger230VAC
Caution
S1 (2x)
Sensor 1 collector
S2 (2x)
S3 (2x)
L
N
R1
Pump L (speed)
N
Pump N
R2
Pump (storage tank 2) L
N
Caution
20VA
D.12
Caution
Solar with swimming pool and heat exchanger
Sensor side
max. 12V
Mains side
2
Danger230VAC
20VA
16
S1 (2x)
Sensor 1 collector
S2 (2x)
Sensor 2 swimming pool
S3 (2x)
L
N
R1
Pump, prim. L (speed)
N
Pump, primary N
R2
Pump, secondary L
N
Pump, secondary N
Installation
D.13
Caution
Solar storage tank/pool
Sensor side
Mains side
max. 12V
2
Danger230VAC
(swimming pool)
Caution
D.14
Caution
20VA
Solar + cooling 1
Sensor side
max. 12V
Mains side
2
Danger230VAC
Description of cooling function see 6.4.1
Caution
S1 (2x)
Sensor 1 collector
S2 (2x)
S3 (2x)
Sensor 3 swimming pool
L
N
R1
Pump L (speed)
N
Pump N
R2
Pump (sec.)+valve L
N
Pump (sec.)+valve N
20VA
S1 (2x)
Sensor 1 collector
S2 (2x)
S3 (2x)
Sensor 3 (optional)
L
N
R1
Pump L (speed)
N
Pump N
R2
Air cooler L
N
Air cooler N
17
Installation
D.15
Caution
Solar + cooling 2
Sensor side
max. 12V
Mains side
2
Danger230VAC
Caution
D.16
Caution
20VA
Solar + cooling 3
Sensor side
max. 12V
Mains side
2
Danger230VAC
18
S1 (2x)
Sensor 1 collector
S2 (2x)
S3 (2x)
Sensor 3 optional
L
N
R1
Pump L (speed)
N
Pump N (speed)
R2
Pump cooler L
N
Pump cooler N
20VA
S1 (2x)
Sensor 1 collector
S2 (2x)
S3 (2x)
L
N
R1
Pump, prim. L (speed)
N
Pump, primary N (speed)
R2
Pump cooler L
N
Pump cooler N
Installation
D.17
Caution
Caution
D.18
Caution
Caution
Solid fuel boiler
Sensor side
max. 12V
Danger
Mains side
230VAC
20VA
S1 (2x)
Fühler 1 solid fuel boiler
S2 (2x)
Fühler 2 storage tank
S3 (2x)
Fühler 3 (optional)
L
N
R1
Pump L (speed)
N
Pump N (speed)
R2
N
Solar + solid fuel boiler
Sensor side
max. 12V
Mains side
2
Danger230VAC
20VA
S1 (2x)
Sensor 1 collector
S2 (2x)
S3 (2x)
Sensor 3 solid fuel boiler
L
N
R1
Pump L (speed)
N
Pump N (speed)
R2
Pump solid fuel L
N
Pump solid fuel N
19
Installation
D.19
Caution
Solar + valve + thermostat
Sensor side
max. 12V
Mains side
2
Danger230VAC
Caution
20VA
D.20
Universal ΔT controller
Caution
Sensor side
max. 12V
Mains side
2
Danger230VAC
Brief description of switching function:
The ΔT function sensor 1 > sensor 2
switches the pump to relay R1.
The thermostat function via sensor 3
Caution
20
20VA
S1 (2x)
Sensor 1 collector
S2 (2x)
S3 (2x)
L
N
R1
Pump L (speed)
N
Pump N
R2
Valve L
N
Valve N
S1 (2x)
Sensor 1 (control)
S2 (2x)
Sensor 2 (reference)
S3 (2x)
Sensor 3 (thermostat)
L
N
R1
Pump L (speed)
N
Pump N
R2
e.g. pump L
N
e.g. pump N
Installation
D.21
Caution
Universal 2x ∆T-controller
Sensor side
max. 12V
Mains side
2
Danger230VAC
Brief description of switching function:
The ΔT function sensor 1 > sensor 2
The ΔT function 2 > sensor 3
Caution
20VA
S1 (2x) Sensor 1 (control)
S2 (2x) Sensor 2 (ref.+contr.)
S3 (2x) Sensor 3 (reference)
L
N
R1
Pump L (speed)
N
Pump N
R2
e.g. pump L
N
e.g. pump N
21
Operation
E.1
Display and input
The display (1), with its extensive text and
graphics mode, is almost self-explanatory,
allowing easy operation of the controller.
(1)
(2)
(3)
(4)
Examples of display symbols:
Pump (rotates in operation)
Valve (direction of flow black)
Collector
Storage tank
Swimming pool
The LED (2) lights up green when a relay
is switched on.
The LED (2) lights up red when
operating mode “Off” is set.
The LED (2) flashes slowly red in the
operating mode “Manual”.
The LED (2) flashes quickly
red when an error is present.
Entries are made using four keys (3+4),
which are assigned to different functions
depending on the situation. The “esc”
key (3) is used to cancel an entry or to
exit a menu. If applicable there will be a
request for confirmation as to whether the
changes which have been made should
be saved.
The function of each of the other three
keys (4) is shown in the display line directly above the keys; the right-hand key
is generally has a confirmation and selection function.
Temperature sensor
Examples of key functions:
Heat exchanger
Warning/error message
New information available
22
+/▼/▲
yes/no
Info
Back
ok
Confirm
= enlarge/shrink values
= scroll menu down/up
= approve/reject
= additional information
= to previous screen
= confirm selection
= confirm setting
Parametrisation
E.2
Commissioning help
The first time the controller is turned on
and after the language and time are set,
a query appears as to whether you want
to parametrise the controller using the
commissioning help or not. The commissioning help can also be terminated or
called up again at any time in the special
functions menu. The commissioning help
guides you through the necessary basic
settings in the correct order, and provides
brief descriptions of each parameter in the display.
Pressing the “esc” key takes you back to the previous value so you can look at the
selected setting again or adjust it if desired. Pressing the “esc“ more than once takes
you back step by step to the selection mode, thus cancelling the commissioning help.
Finally, menu 4.2 under operating mode “Manual” should be used to test the switch
outputs with the consumers connected, and to check the sensor values for plausibility.
Then switch on automatic mode.
Caution
E.3
Observe the explanations for the the individual parameters on the following pages, and check whether further settings are necessary for your
application.
Free commissioning
If you decide not to use the commissioning help, you should make the necessary settings in the following sequence:
- Menu 10.
Language (see 14.)
- Menu 7.2
Time and date (see 12.2)
- Menu 7.1
Program selection (see 12.1)
- Menu 5.
Settings, all values (see 10.)
- Menu 6.
Protective functions if adaptations are necessary (see 11.)
- Menu 7.
Special functions if additional changes are necessary (see 12.)
Finally, menu 4.2 under operating mode “Manual“ should be used to test the switch
outputs with the consumers connected, and to check the sensor values for plausibility.
Then switch on automatic mode.
Caution
Observe the explanations for the the individual parameters on the following pages, and check whether further settings are necessary for your
application.
23
Operation
E.4
Menu sequence and menu structure
The graphics or overview mode appears
when no key has been press for 2 minutes, or when the main menu is exited by
pressing “esc“.
Pressing a key in graphics or overview
mode takes you directly to the main menu.
The following menu items are then available for selection there:
1. Measurements
Current temperature values with explanations
2. Statistics
Function control of the system with operating hours, etc
3. Display Mode
4. Operating Mode
Automatic mode, manual mode or switch
unit off
5. Settings
Set parameters needed for normal operation
6. Protections
Solar and frost protection, recooling, antiseizing protection
7. Special functions
8. Menu lock
9. Service data
10. Language
24
Select graphics mode or overview mode
Program selection, sensor cali-bration,
clock, additional sensor, etc.
Against unintentional setting chan-ges at
critical points
For diagnosis in the event of
an error
Language selection
Measurement values
1.
Measurement values
The menu “1. Measurement values”
serves to display the currently measured
temperatures.
The menu is closed by pressing “esc” or
selecting “Exit measurement values”.
Selecting “Info” leads to a brief help text
explaining the measurement values.
Selecting “Overview” or “esc” exits the
Info mode.
Caution
If “--” appears on the display instead of the measurement value, then
there may be a defective or incorrect temperature sensor.
If the cables are too long or the sensors are not placed optimally, the
result may be small deviations in the measurement values. In this case
the display values can be compensated for by making entries on the
controller. Follow the instructions under 7.3.
What measurement values are displayed depends on the selected program, the connected sensors and the specific device design.
25
Statistics
2.
Statistics
The menu “2. Statistics” is used for function control and long-term monitoring of
the system.
selecting “Exit statistics”.
Caution
For analysis of the system data it is essential for the time to be set accurately on the controller. Please note that the clock does not continue
to run if the mains voltage is interrupted, and must therefore be reset.
Improper operation or an incorrect time may result in data being deleted,
recorded incorrectly or overwritten.
The manufacturer accepts no liability for the recorded data!
2.1 Operating hours
Display of operating hours of the solar pump connected to the controller; various time
ranges (day-year) are available.
2.2 Average temperature difference ∆T
Display of the average temperature difference between the reference sensors of the
solar system with the consumer switched on.
2.3 Heat output
Display of the heat output of the system.
2.4 Graphic overview
This provides a clearly-organised display of the data listed under 2.1-2.3 as a bar
graph. Various time ranges are available for comparison. The two left-hand keys can
be used to page through the data.
2.5 Message log
Display of the last 10 events occurring in the system with indication of date and time.
2.6 Reset/clear
Resetting and deleting the individual analyses. The function “All statistics” clears all
analyses but not the error messages.
26
Display mode
3.
Display mode
Menu “3. Display mode” is used to define
the controller’s display for normal operation.
This display appears whenever two minutes go by without any key being pressed.
The main menu appears again when a
key is pressed.
selecting “Exit display mode”.
3.1 Schematic
In graphics mode, the selected hydraulic systems are depicted with the measured
temperatures and operating states of the connected consumers.
3.2 Overview
In overview mode, the measured temperatures and operating states of the connected
consumers are depicted in text form.
3.3 Alternating
In alternating mode the schematic mode and then the overview mode are active for 5
seconds at a time.
27
Operating modes
4.
Operating modes
In menu “4. Operating modes” the controller can either be placed in automatic
mode, switched off, or placed in a manual
operating mode.
selecting “Exit operating modes”.
4.1 Automatic
Automatic mode is the normal operating mode of the controller. Only automatic mode
provides proper controller function taking into account the current temperatures and
the parameters that have been set! After an interruption of the mains voltage the controller automatically returns to the last operating mode selected!
4.2 Manual
The relay and thus the connected consumer are switched on and off by pressing a
key, with no regard to the current temperatures and the parameters which have been
set. The measured temperatures are also shown to provide an overview and function
control.
Danger
When operating mode “Manual” is activated, the current temperatures
and the selected parameters are no longer considered. There is a danger of scalding or serious damage to the system. The operating mode
“Manual” may only be used by specialists for brief function tests or during commissioning!
4.3 Off
Caution
When the operating mode “Off” is activated, all controller functions are
switched off. This can lead, for example, to overheating on the solar
collector or other system components. The measured temperatures are
sstill displayed to provide an overview.
4.4 Fill system
Caution
28
This special operating mode is intended only for the filling procedure for
a special “Drain Master System” with a fill level contact parallel to collector sensor S1. The instructions on the display must be followed when
filling the system. Be sure to terminate the function when finished!
Settings
5.
Settings
The necessary basic settings required for
the control function are made in menu “5.
Settings”.
Caution
This does not under any circumstances
replace the safety facilities to be
provided by the customer!
The menu is closed by pressing “esc” or selecting “Exit settings”.
Caution
Various settings can be made depending on the selection of hydraulic variant
1-20. This is explained in more detail in Table 5.17. This table also indicates the
associated reference sensors and switch outputs. The following pages contain
generally valid descriptions for the settings.
5.1 Tmin S1
Enable/start temperature at sensor 1
If this value is exceeded at sensor 1 and the other conditions are also met, then the
controller switches the associated pump and/or valve on. If the temperature at sensor 1 drops below this value by 5°C, then the pump and/or the valve are switched off
again.
Setting range: from 0°C to 99°C/default setting: 20°C
5.2 Tmin S2
again.
5.3 Tmin S3
again.
29
Settings
5.4 Tmax S2
Switch-off temperature at sensor 2
controller switches the associated pump and/or valve off. If sensor 2 falls below this
value again and the other conditions are also met, then the controller switches the
pump and/or valve on again.
Setting range: from 0°C to 99°C/default setting: 60°C (30°C in pool variants)
Danger
Temperature values which are set too high can lead to scalding or damage to the system. Scalding protection must be provided by the customer!
5.5 Tmax S3
Switch-off temperature at sensor 3
controller switches the associated pump and/or valve off. If sensor 3 falls below this
value again and the other conditions are also met, then the controller switches the
pump and/or valve on again.
Setting range: from 0°C to 99°C/default setting: 60°C (30°C in pool variants; in hydraulic variants without S3 default: Off)
Danger
5.6 ∆T R1
Switch-on/switch-off temperature difference for relay R1
If this temperature difference between the reference sensors is exceeded and the
other conditions are also met, then the controller switches the relay R1 on.
When the temperature drops to ΔT Off, then R1 is switched off.
Settings range: ΔT from 4°C to 20°C / ΔTOff from 2°C to 19°C
Settings range: ΔT 10°C / ΔT off 3°C.
Caution
30
If the set temperature difference is too small, this may result in ineffective operation, depending on the system and sensor positions.
Special switching conditions apply for speed control (see 7.9)!
Settings
5.7 ∆T R2
Switch-on/Switch-off temperature difference for relay R2
If this temperature difference between the reference sensors is exceeded and the
other conditions are also met, then the controller switches the pump and/or the valve
on.
When the temperature drops to ΔT Off, then R2 is switched off.
Settings range: ΔT from 4°C to 20°C / ΔTOff from 2°C to 19°C
Settings range: ΔT 10°C / ΔT off 3°C.
Caution
Setting the temperature difference too small may lead to ineffective operation
of the system and to frequent switching of the pump, depending on the system
and sensor positions.
5.8 Tset S3
Thermostat function at sensor 3
If the temperature at sensor 3 exceeds this value (+hysteresis) the corresponding relay
is switched off. If the temperature at sensor 3 falls below this value and the other conditions are also met, the corresponding relay is switched on.
Danger
In Energy saving mode other settings may apply, e.g. TecoS3, see 5.16
Caution
5.9 Hysteresis
Hysteresis for thermostat function at sensor 3
By setting the hysteresis value the heating of the storage tank can be adjusted.If the
temperature of the Tsetpoint at sensor 3 is exceeded by the set hysteresis, additional
heating at relais 2 is deactivated. If the Energy saving mode is active (see 5.16) the
system heats up until TminS3+hysteresis temperature is reached.
31
Settings
5.10 Priority sensor
Charging priority in systems with two storage tanks
A setting must be made as to which storage tank (storage tank sensor) has priority for
charging. Charging of the lower-priority storage tank is interrupted at regular intervals
to check whether the temperature increase at the collector can enable charging of the
higher-priority storage tank.
Setting range: S2 or S3/default setting: S2
5.11 T priority
Temperature threshold for absolute priority
In systems with two storage tanks charging of the lower-priority storage tank will never
take place until this temperature at sensor of the higher-priority storage tank is exceeded.
5.12 Loading time
Interruption of charging into the lower priority storage tank
The charging of the lower-priority storage tank is interrupted after the settable time
in order to check whether the collector has reached a temperature level that allows
charging in the higher-priority storage tank. If so, the priority storage tank is charged.
If not, the increase is measured (see 5.13), to check if charging of the priority storage
tank will be possible shortly.
Setting range: from 1 to 90 minutes/default setting: 10 minutes
5.13 Increase
Extension of the charging pause due to temperature increase in the collector
For precise setting of the charging priorities for systems with multiple storage tanks,
the necessary temperature increase of the collector at which the interruption of the
charging into the lower-priority storage tank is extended by one minute is set here. The
interruption is extended because the temperature increase of the collector is expected
to enable charging in the higher-priority storage tank soon.
As soon as ∆T conditions are met, the priority storage tank is charged. If the rise in
temperature falls below the set value, then the charging of the lower-priority storage
tank is enabled again.
5.14 Thermostat periods
Thermostat activity times
Set the desired periods of time when the thermostat should be active. 2
periods can be set per day, settings can also be copied to other days.
Outside the set times the thermostat is switched off.
Setting range: from 00:00 to 23:59 /default setting: 06:00 to 22:00
32
Settings
5.15 „Party Function“
With the party function the storage temperature is heated up once to the reference
temperature (TrefS3+hysteresis, respectively TecoS3+hysteresis in energy saving
mode). The party mode is activated by pressing the „esc“-key for 3 seconds in the
main menu. While this mode is active, the system heats up to the reference value +
hysteresis, unattached to preset thermostat times. The mode is ended once the required temperature is reached.
Caution
Caution
Party function is not activated by menu. The ESC key has to be pressed for 3
seconds.
During Energy saving mode, Party function heats up to TrefS3+hysteresis,
respectively TecoS3+hysteresis in Energy savings mode
5.16 Energy saving mode
Energy saving mode for the thermostat function
In energy saving mode the additional heating via R2 is switched on at TecoS3 and
heats up to Teco+hysteresis. When energy saving mode is active, but no solar heat is
available, TsetS3 is used like in normal mode.
Settings range: On, Off/ Default: Off
5.17 TecoS3
Minimum temperature S3 in Energy saving mode
If the temperature at sensor 3 falls below this value and the thermostat function is active (see 5.14 thermostat periods), additional heating via relais R2 is switched on until
TminS3 + hysteresis is reached (see 5.9 hysteresis).
Settings range : 0°C to 99°C / Default: 20°C
33
34
S3
=>R2
S1/S2
=>R1
S3
=>R1+R2
S1/S2
=>R1+R2
T R1
S3
=>R1+R2
S1
=>R1
7
S3
=>R2
S1
=>R1
8
S3/S2
=>R2
S1/S2
=>R1
S1/S2
=>R1
S1/S3
=>R1+R2
S1/S3
=>R2
S1/S2
=>R1
S3
=>R2
S2
=>R1
S1
=>R1+R2
10
S2/S3
=>R2
S1/S2
=>R1
S3
=>R2
S2
=>R1
S2
=>R2
S1
=>R1
11
S1/S2
=>R1
S3/S2
=>R2
S2
=>R1+R2
S1
=>R1
12
S2 o. S3
=>R1/R2
S1/S2
=>R1
S1/S3
=>R1+R2
S3
=>R1+R2
S2
=>R1
S1
=>R1
13
S1/S2
=>R1
S3
=>R2
S2
=>R1
S1
=>R1
14
S1/S2
=>R1
S3
=>R2
S2
=>R1
S1
=>R1
15
S1/S2
=>R1
S3
=>R2
S2
=>R1
S1
=>R1
16
S2 o. S3 S2 o. S3
=>R1/R2 =>R1/R2
S2 o.S3 S2 o.S3
=>R1/R2 =>R1/R2
S2 o. S3
=>R1/R2
S2 o.S3
=>R1/R2
T-priority
T-etusijaisuus
S2 o.S3
=>R1/R2
S3
=>R2
S1/S2
=>R1
S3/S2
=>R1+R2
S3
=>R1+R2
S2
=>R1
S1
=>R1
9
S3
=>R2
S1/S2
=>R2
S3/S2
=>R1
S2
S2
S2
=>R1+R2 =>R1+R2 =>R1+R2
S1
=>R2
6
Priority
S1/S2
=>R1
S1/S3
=>R1+R2
S3
=>R1+R2
S2
=>R1
S1
=>R1
5
S3
=>R2
S2/S3
=>R2
S1/S2
=>R1
S3
=>R2
S2
=>R1
S2
=>R2
S1
=>R1
4
S3
=>R2
S1/S2
=>R1
S3/S2
=>R2
S2
=>R1+R2
S1
=>R1
3
Hysteresis
Tset S3
T R2
S2
=>R1
S2
=>R1+R2
S3
=>R2
S1
=>R1
S1
=>R1+R2
Tmax S3
Tmax S2
Tmin S3
Tmin S2
Tmin S1
2
1
S3/S2
=>R2
S1/S2
=>R1
S2
=>R1+R2
S3
=>R2
S1
=>R1
17
S1/S2
=>R1
S2
=>R1
S1
=>R1
18
S3
=>R2
S3
=>R2
S1/S2
=>R1
S3
=>R2
S2
=>R1
S3
=>R2
S1
=>R1
19
S3
=>R2
S3
=>R2
S1/S2
=>R1
S3
=>R2
S2
=>R1
S1
=>R1
20
S2/S3
=>R2
S1/S2
=>R1
S3
=>R2
S2
=>R1
S2
=>R2
S1
=>R1
21
The table lists the settings corresponding to the specific programs (hydraulic variants). The reference sensors 1-3 corresponding to the functions
are labelled S1-S3. The switch outputs (relays) corresponding to the functions for pumps and valves are labelled with R1 or R2. The settings,
setting ranges and default settings are explained under 5.
5.18 Table: Programs (hydraulic variants) with associated settings
Settings
6.
Menu “6. Protective functions” can be used to
activate and set various protective functions.
Caution
This does not under any circumstances
replace the safety facilities to be
provided by the customer!
The menu is closed by pressing “esc” or selecting “Exit settings”.
6.1 Seizing protection
If the seizing protection is activated, then the controller switches the relay in question and the
connected consumer on every day at 12:00 and on Sundays at 12:00 for 5 seconds in order to
prevent the pump and/or the valve from sticking after an extended stationary period.
Setting range R1: daily, weekly, off/default setting: Off
Setting range R2: daily, weekly, off/default setting: Off
6.2 Frost protection
A two-stage frost protection function can be activated. In stage 1 the controller switches the
pump on for 1 minute every hour if the collector temperature drops below the set value “Frost
stage 1”.
If the collector temperature drops further to the set value “Frost stage 2” the controller switches
the pump on continuously.
If the collector temperature then exceeds the value “Frost stage 2” by 2°C, then the pump
switches off again.
Frost protection setting range: on, off/default setting: off
Frost stage 1 setting range: from -25°C to 10°C or off/default setting: 7°C
Frost stage 2 setting range: from -25°C to 8°C/default setting: 5°C
Caution
This function causes energy to be lost via the collector! It is normally not activated
for solar systems with antifreeze.
Observe the operating instructions for the other system components!
35
6.3 System protection
priority protection
System protection prevents overheating of system components by automatic shutdown
of the solar pump. If “SProt Ton” is exceeded at the collector, the pump is switched off.
The pump is activated again when the temperature drops below “SProt TOff”.
Automatic shutdown - settings range: On / Off / Default: on
SProt Ton - settings range: 60 °C to 150 °C / Default: 120 °C
SProt Toff - settings range: 50 °C to Ton minus 5 °C / Default: 115 °C
Caution
When system protection is on, the temperature in the idle collector will be very
high, thus the pressure in the system will rise and can damage your system.
Pay close attention to the instructions of the system manufacturer.
6.4 Collector protection
Collector protection prevents overheating of the collector. The pump is switched on to
transfer heat from the collector to the storage tank.
If “CP Ton” is exceeded at the collector sensor, the pump is switched on until the temperature reaches “CP Toff” or the temperature “CP Tmax storage” is exceeded in the
storage or pool.
Collektor protection settings range: on / off / Voreinstellung: off
CP Ton settings range: 60°C to 150°C / Default: 110°C
CP Toff settings range: 50°C to Ton minus 5°C / Default: 100°C
CP Tmax storagesettings range: 0°C to 140°C / Default: 90°C
Danger
When collector protection is active, the storage or pool is heated well
beyond Tmax S2 (see 5.2) which can result in scalding and system damage.
Cooling functions ->
36
6.4.1 Cooling functions
The hydraulic variants are set in menu „7.1 Program selection“
Hydraulic Variant D.14 Solar + cooling 1:
If „CProt Ton“ is exceeded at S1, the cooler at R2 is switched on till the temperature
drops to „CProt Toff“. If the storage tank exceeds „CProt Tmax storage“, the system is
switched off.
If „CProt Ton“ is exceeded at S1, the cooler at R2 is switched on. If the storage tank
exceeds „CProt Tmax storage“, R1 is switched off with R2 still running to keep on cooling. If the temperature at S1 drops to „CProt Toff“, cooling is switched off.
If „CProt Ton“ is exceeded at S1, the pump at R1 is switched on to cool the collector by
heating up the storage tank.
If the storage tank S2 reaches „CProt Tmax storage“, R1 is switched off.
Once the storage tank at S3 exceeds TsetS3, cooling at R2 is switched on till „TsetS3“hysteresis is reached.
6.5 Col.- Alarm
If this temperature is exceeded at the collector sensor when the solar pump is on a
warning or error message is triggered. A warning message is shown in the display.
Collector alarm settings range: on / off / Default: off
Col. alarm - setting range: 60 °C to 300 °C / Default: 150 °C
6.6 Recooling
In hydraulic systems with solar when the recooling function is activated excess energy from
the storage tank is fed back into the collector. This only takes place if the temperature in the
storage tank is higher than the value “Recool Tsetpoint” and the collector is at least 20°C cooler
than the storage tank and before the storage tank temperature has dropped below the value
“Recool Tsetpoint”. In systems with two storage tanks the setting applies to both storage
tanks.
Recooling setting range: on, off/default setting: off
Recooling Tsetpoint setting range: from 0°C to 99°C/default setting: 70°C
Caution
This function causes energy to be lost via the collector! Recooling
should only be exceptionally.
37
6.7 Anti-Legionella
With the “AL function” activated the TDC 3 makes it possible to heat the storage tank
to a higher temperature (“AL Tsetpoint S2”, provided that the energy source allows
this. Time periods when the AL heat up is attempted are to be setup in the menu
“AL times” Once the temperature “AL Tset S2” is reached, the controller will try to
maintain this temperature for the time period set in “AL residence time”. When this is
successful, the time and date is saved and displayed in the menulog “AL heat”.
AL Function settings range: on / off / Default: off
AL Tset S2 settings range: 60°C to 99°C / Default: 70°C
AL residence time - settings range: 1 to 60 minutes / Default: 15 minutes
AL heat. (no setting): Displays the date and time of the last successful AL heat up
AL times - settings range: Mo-Su , 0-24h/ Default: daily 3-5h
Caution
Danger
Caution
38
The anti-Legionella function is switched off at delivery.
This function is only relevant for storage tanks where sensor 2 is installed. Whenever heating-up has been carried out with the anti-Legionella function being switched on, an information message with the date
is shown in the display.
During the anti-Legionella function the storage tank is heated up
over the set value “Tmax S2”, which can lead to scalding and
damage to the system.
This anti-Legionella function does not provide complete protection
against Legionella, because the controller is dependent on sufficient
energy being fed in, and it is not possible to monitor the temperatures in
the entire range of the storage tanks and the connected piping system.
To provide complete protection against Legionella bacteria, it must be
ensured that the temperature is raised to the necessary temperature,
and at the same time there must be water circulation in the storage tank
and piping system by means of other additional energy sources and
control units.
Special functions
7.
Special functions
Menu “7. Special functions” is used to set basic
items and expanded functions.
Other than the time all settings may
only be made by a specialist.
Caution
The menu is closed by pressing “esc” or selecting “Exit special functions”.
7.1 Program selections
The suitable hydraulic variant for the specific application is selected and set here (see
B.5 Hydraulic variants). The associated diagram can be displayed by pressing “info”.
Setting range: 1-15/default setting: 1
Caution
Normally the program selection is made only once during initial commissioning by the specialist. Incorrect program selection can lead to
unpredictable errors.
7.2 Time & date
This menu is used to set the current time and date.
Caution
For analysis of the system data it is essential for the time to be set accurately
on the controller. Please note that the clock does not continue to run if the mains
voltage is interrupted, and must therefore be reset.
7.3 Sensor calibration
Deviations in the temperature values displayed, for example due to cables which are to
long or sensors which are not positioned optimally, can be compensated for manually
here. The settings can be made for each individual sensor in steps of 0.5°C.
Offset S1...S3 per setting range: -100 to +100 (translates to -50°C...+50°C)
Default setting: 0
Caution
Settings are only necessary in special cases at the time of initial commissioning by the specialist. Incorrect measurement values can lead to
unpredictable errors.
39
Special functions
7.4 Commissioning
Starting the commissioning help guides you in the correct order through the basic settings necessary for commissioning, and provides brief descriptions of each parameter
in the display.
Pressing the “esc” key takes you back to the previous value so you can look at the selected setting again or adjust it if desired. Pressing the “esc” more than once takes you
back to the selection mode, thus cancelling the commissioning help. (see also E.2).
Caution
May only be started by a specialist during commissioning! Observe the
explanations for the the individual parameters in these instructions, and
check whether further settings are necessary for your application.
7.5 Factory settings
All of the settings that have been made can be reset, thus returning the controller to its delivery
state.
Caution
The entire parametrisation, analyses, etc. of the controller will be lost
irrevocably. The controller must then be commissioned once again.
7.6 Expansions
This menu can only be selected and used if additional options or expansions have
been built into the controller.
The associated supplementary installation, mounting and operation instructions are
then included with the specific expansion.
7.7 Heat quantity
A simple heat metering function for basic system control can be activated in this menu. Additional
settings regarding the glycol, the percentage of gylcol and the flow rate of the system are
required.
Resulting data is only approximate value for function control!
Caution
40
Special functions
7.7.1
Heat metering
Activate or deactivate the heat metering function
Settings range: On/off /default setting: Off
7.7.2
AF type
Adjust the type of glycol that has been used in the system.
Settings range: Ethylene/Propylene /default setting: Ethylene
7.7.3
Glycol portion
Adjust the percentage of glycol that has been used in the system.
Settings range: 0-60% /default setting: 40%
7.7.4
Flow rate
Adjust the flow rate according to the system.
Settings range: 10-5000 l/h /default setting: 500 l/h
7.7.5
∆T Offset
Since the calculation of the heat metering is based on the temperature of the collector and storage where measuring takes place, a possible deviation from the flow and
return temperature can be compensated with this value.
Example: Displayed collector temp. 40° C, measured flow temp. 39° C, displayed storage temp. 30° C, measured return temp. 31° C means a setting of -20% (Displayed T
10K, actual T 8K => -20% correction value)
Settings range: -50% to +50% /default settings: 0%
7.8 Start aid function
With some solar systems, especially with vacuum tube collectors, it may occur that the
measurement value acquisition at the collector sensor occurs too slowly or too inaccurately because the sensor is often not at the hottest location. When the start help is
activated the following sequence is carried out:
If the temperature at the collector sensor increases by the value specified under
“Increase” within one minute, then the solar pump is switched on for the set “Purging time” so that the medium to be measured can be moved to the collector sensor. If
this still does not result in a normal switch-on condition, then the start help function is
subject to a 5-minute lockout time.
Start help setting range: on, off/default setting: off
Purging time setting range: 2 ... 30 sec./default setting: 5 sec.
Increase setting range: 1°C....10°C/default setting: 3°C/min.
Caution
This function should only be activated by a specialist if problems arise
with acquisition of measurement values. In particular follow the instructions from the collector manufacturer.
41
Special functions
7.9 Speed control
If the speed control is activated, the TDC3 makes it possible to vary the speed of standard
pumps at relay R1 by means of special internal electronics.
Caution
This function should only be activated by a specialist. Depending on the
pump and pump stage used, the minimum speed should not be set too
low, because otherwise the pump or the system may be damaged. The
information provided by the relevant manufacturer must also be observed! If in doubt, the min. speed and the pump stage should generally
be set to high rather than too low.
7.9.1 Variant
The following speed variants are available here:
Off: There is no speed control. The connected pump is only switched on or off with full
speed.
Variant V1: After the purging time the controller switches to the set max. speed. If
the temperature difference ∆T between the reference sensors (collector and storage
tank) is less than the set value, then the speed is decreased by one stage after the
control time elapses. If the temperature difference between the reference sensors is
greater than the set value, then the speed is increased by one stage after the control
time elapses. If the controller has adjusted the speed of the pump down to the smallest
stage and the ∆T between the reference sensors is ∆T off, the pump is switched off.
Variant V2: After the purging time the controller switches to the set min. speed. If the
temperature difference ∆T between the reference sensors (collector and storage tank)
is greater than the set value, then the speed is increased by one stage after the control
time elapses. If the temperature difference ∆T between the reference sensors is below
the set value, then the speed is decreased by one stage after the control time elapses.
If the controller has adjusted the speed of the pump down to the smallest stage and
the ∆T between the reference sensors is T∆off, the pump is switched off.
Variant V3: After the purging time the controller switches to the set min. speed. If the
temperature at the reference sensor (collector) is greater than the setpoint to be set
subsequently, then the speed is increased by one stage after the control time expires.
If the temperature at the reference sensor (collector) is less than the setpoint to be set
subsequently, then the speed is decreased by one stage after the control time expires.
Setting range: V1,V2,V3, off/default setting: off
Variant V4: (2 storages)
When the valve is set toward the primary storage, speed control works as in V3.
When the valve is set toward the secondary storage, speed control works as in V2.
Settings range: V1,V2,V3, Off / Default: Off
Speed control settings continued on page 42
42
Special functions
7.9.2 Purging time
During this time the pump starts up at its full speed (100%) to ensure reliable starting.
Only after this purging time does the pump run with speed control and switches to the
max. or min. speed, depending on the variant set.
Setting range: from 5 to 600 seconds/default setting: 8 seconds
7.9.3 Sweep time
The control time is used to determine the delay for speed control in order to avoid
large temperature oscillations as much as possible. The time span required for a complete control process from minimum speed to maximum speed is entered here.
Setting range: from 1 to 15 minutes/default setting: 4 minutes
7.9.4 Max. speed
The maximum speed of the pump at relay R1 is specified here. During the setting the
pump runs at the specified speed and the flow rate can be determined.
Setting range: from 70 to 100%/default setting: 100%
Caution
The indicated percentages are guide values that may vary to a greater
or lesser extent depending on the system, pump and pump stage.
7.9.5 Min. speed
The minimum speed of the pump at relay R1 is specified here. During the setting the
pump runs at the specified speed and the flow rate can be determined.
Setting range: from 30 to max. speed -5%/default setting: 50%
Caution
The indicated percentages are guide values that may vary to a greater
or lesser extent depending on the system, pump and pump stage.
7.9.6 Setpoint
This value is the control setpoint for variant 3. If the value at the collector sensor drops
below this, the speed is reduced. If it rises above this, the speed is increased.
Setting range: from 0 to 90°C/default setting: 60°C
43
Menu lock
8.
Menu lock
Menu “8. Menu lock” can be used to secure
the controller against unintentional changing
of the set values.
The menu is closed by pressing “esc” or selecting “Exit menu lock”.
The menus listed below remain completely accessible despite the menu lock being
activated, and can be used to make adjustments if necessary:
1.
Measurement values
2.
Analysis
3.
Display mode
7.2.
Time&date
8.
Menu lock
9.
Service values
To lock the other menus, select “Menu lock on”.
To enable the menus again, select “Menu lock off”.
Setting range: on, off/default setting: off
Language
10.
Language
Menu “10. Language” can be used to select the language for the menu guidance.
This is queried automatically during initial
commissioning.
The choice of languages may differ,
however, depending on the device design.
Language selection is not available in
every device design!
44
Service values
9.
Service values
The menu “9. Service values” can be used for
remote diagnosis by a specialist or the manufacturer in the event of an error, etc.
Enter the values at the time when the
error occurs e.g. in the table.
Caution
The menu can be closed at any time by pressing “esc”.
45
Malfunctions
Z.1.
Malfunctions with error messages
(LED flashes +
warning symbol)
If the controller detects a malfunction, the
red light flashes and the warning symbol
also appears in the display. If the error
is no longer present, the warning symbol
changes to an info symbol and the red
light no longer flashes.
To obtain more detailed information on the
error, press the key under the warning or
info symbol.
Danger
Do not try to deal with this
yourself.
Consult a specialist in the
event of an error!
Possible error messages:
Notes for the specialist:
Sensor x defective ---------------->
Means that either the sensor, the sensor input
at the controller or the connecting cable is/was
defective.
(Resistance table see B.1)
Collector alarm -------------------->
Means that the collector has fallen/fell below the
temperature set under menu 6.5
Night circulation ------------------->
Means that the solar pump is/was in operation
between 23:00 and 04:00. (Exception see 6.6)
Restart ------------------------------> Means that the controller was restarted, for example due to a power failure. Check the date&time!
Time&date ------------------------->
46
This message appears automatically after a
mains failure because the time&date have to be
checked, and reset if necessary.
Malfunctions
Z.2
Replacing the fuse
Danger
Danger
Repairs and maintenance may only be performed by a specialist. Before
working on the unit, switch off the power supply and secure it against
being switched on again! Check for the absence of power!
Only use the supplied spare fuse or a fuse of the same design with the
following specifications: T2A 250V
Z.2.1
Fuse
Z.3
If the mains voltage is switched on and
the controller still does not function or
display anything, then the internal device
fuse may be defective. In that case, open
the device as described under C, remove
the old fuse and check it.
Exchange the defective fuse for a new
one, locate the external source of the error (e.g. pump) and exchange it.
Then first recommission the controller and
check the function of the switch outputs in
manual mode as described under 4.2.
Maintenance
Caution
In the course of the general annual maintenance of your heating system
you should also have the functions of the controller checked by a specialist and have the settings optimised if necessary.
Performing maintenance:
- Check the date and time (see 7.2)
- Assess/check plausibility of analyses (see 2.4)
- Check the error memory (see 2.5)
- Verify/check plausibility of the current measurement values (see 1.)
- Check the switch outputs/consumers in manual mode (see 4.2)
- Poss. optimise the parameter settings
47
Instead of setting the flow rate for the system using a flow rate limiter, it is better
to adjust the flow rate using the switch on the pump and by means of the “max.
speed” setting on the controller (see 7.9.4). This saves electricity!
The service values (see 9.) include not only current measurement values and
operating states, but also all of the settings for the controller. Write the service
values down just once after commissioning has been successfully completed.
In the event of uncertainty as to the control response or malfunctions the service
values are a proven and successful method for remote diagnosis. Write the service values down (see 9.) at the time that the suspected malfunction occurs. Send
the service value table by fax or e-mail with a brief description of the error to the
specialist or manufacturer.
In program 1 “Solar with storage tank” the mechanical relay R2 switches together
with the speed-controlled output R1. Relay output R2 can be used to operate
larger loads up to 460VA, as well as valves or auxiliary relays with low power.
In program 13 “Solar with storage tank and pool” the charging of the pool, e.g. for
winter operation, can be switched off using a simple function. To do this, simply
press and hold the “esc” key down for several seconds on the diagram/overview
screen. A message appears on the display as soon as the pool is switched off or
when the pool is switched on again.
Programs 20 + 21 “Universal ∆T controller” are suitable, for example, for hydraulic variants with solid-fired boiler, follow-on storage tank charging, storage tank
transfer, heating circuit return lift, etc.
The Operating hours displayed in the “Analysis” menu are solar operating hours.
This therefore only takes into account hours in which the solar pump is active. In
the universal programs 20 + 21 the times refer to relay R1.
To protect against loss of data, record any analyses and data that are particularly
important to you (see 2.) at regular intervals.
Final declaration:
Although these instructions have been created with the greatest possible care, the possibility of incorrect or incomplete information cannot be
excluded. Subject as a basic principle to errors and technical changes.
Manufacturer:
SOREL GmbH Mikroelektronik
Jahnstr. 36
D - 45549 Sprockhövel
Tel. +49 (0)2339 6024
Fax +49 (0)2339 6025
www.sorel.de [email protected]
48
Your specialist dealer:
L:\Bedienanleitungen\S\TDC\TDC3 5L Englisch Redesign\TDC3 5L english100896.indd
Hydraulic variant set:
Commissioned on:
Commissioned by:

Temperature Difference Controller TDC 3

Transcription

Similar documents

ASSURANCE - Sensaphone

Wireless Sensor Troubleshooting Guide

CARDELL Quick Reference Guide

GM MAF Instructions

AS AC series

Temperature Difference Controller TDC 3

Installation Guide

SENSOR-ROSEE 3rd Newsletter - South

Pannello Luminoso Smart Sensor

UniPixel Investor Presentation Dec 2015 NASDAQ: UNXL

Autocirc® Instant Hot Water Pump