Edco Scarafier Specifications - One Source Equipment Rentals

Transcription

Edco Scarafier Specifications - One Source Equipment Rentals
SCARIFIERS
SURFACE PREPARATION
Scarifiers are Versatile Milling Machines that Stand Up to Any Required Removal Prep Work
Clean
Texture
Level
Groove
Remove
• Warehouse Floors
• Manufacturing Facilities
• Service Bays
• Prepare surfaces for better
Adhesion of Coatings
• Sidewalk Irregularities
• Uneven Joints
• Bumps
• Uneven Surfaces
needing repair
• Walkways
• Bridge Decks
• Dairy Barns
• Parking Decks
• Traffic Lines
• Coatings & Paint
• Ice
• Mortar
• Delaminated surfaces
• Contaminant’s
like dirt & oil
EDCO Scarifiers apply a cutting wheel to the concrete surface. EDCO Scarifier Drums flail cutters at the surface, leaving a clean, textured
or roughened finish. These Scarifiers allow you to control depth of cut more precisely than a scabbling machine. EDCOs multi-tasking
Scarifiers have various styles of interchangeable cutter assembles that can be used for cleaning, grinding and light to heavy milling.
WITH EDCO’s SCARIFIERS, YOU CAN CHOOSE FROM A VARIETY OF ACCESSORIES AND
CUTTERS TO ACHIEVE THE PROFILE, DEPTH AND SPEED FOR THE JOB.
• Choose the power source you need — electric or gasoline
• Heavy-duty 7-gauge frame is built for years of performance
• Variable depth settings provide greater control of surface removal
• Easy Loading Drums allow you to change your Drum Set-up in minutes
• EDCO’s Unique Engage/Disengage Lever lets you raise and lower Cutting Drum without losing depth setting
• Vacuum Ports are standard for dust-free Scarifier operation - Feed hookups are standard on Self- Propelled models
Distributed By:
One Source Equipment Rentals
www.onesourcerental.com
SCARIFIERS
SURFACE PREPARATION
8” WALK BEHIND SCARIFIER
MODEL #
PART # POWER
HORSE POWER
PHASE
AMPS
*RPM’s BELTS
LENGTH
WIDTH
HEIGHT
WEIGHT
CPM-8-5
79500
Electric
5 HP, 230 V
Single
19.8
2160
Std “V” Belts
35”
20”
39”
220 lbs
CPM-8-5
79400
Electric
5 HP, 230/460 V
Three
12/6
2130
Std “V” Belts
35”
20”
39”
220 lbs
CPM-8-9H
79300
Gasoline *9 HP
N/A
N/A
2150
Cgd “V” Belts 35”
20”
39”
190 lbs
PRODUCTION RATE:
8” Working Width will scarify approximately 350-500 square feet per hour
at Depth Per Pass of 1/8” • Removes traffic lines at 800-1000 lineal feet per hour
PRODUCT NOTES:
Optional edger attachment allows the CPM-8 to get within 13⁄4” of any vertical surface
IDEAL FOR: Sidewalk trip hazard repair • Concrete coatings removal • Floor cleaning and or preparation
• Traffic line and markings removal • Creating non-slip surfaces
Edger Assembly Part # 65027 / Edger Drum Part # C66040
NUMEROUS CUTTER DRUM SET-UPS ARE AVAILABLE INCLUDING DIAMOND
BLADE GROOVING SET-UPS TO ACHIEVE VARIOUS SURFACE PROFILES
* RPM’s are based on the machine’s accessory speed.
* NET HORSEPOWER STATEMENT - *As rated by the engine manufacturer. The power rating of the engine indicated in this document is the net power output tested on a production engine for the engine model and measured in accordance
with SAE j1349 at 3600 rpm. Mass production engines may vary from this value. Actual power output for the engine installed in the final machine will vary depending on numerous factors, including the opening speed of the engine in
application, environmental conditions, maintenance, and other variables.
Distributed By:
One Source Equipment Rentals
www.onesourcerental.com
SCARIFIERS
SURFACE PREPARATION
8” SCARI-LITE MINI-PLANER
MODEL #
PART # POWER
HORSE POWER
PHASE
AMPS
*RPM’s BELTS
CPL-8-1.5
69300
Electric
1.5 HP, 115 V
Single
17.2
1100
CPL-8-5.5H
69500
Gasoline *5.5 HP
N/A
N/A
2200
PRODUCTION RATE:
LENGTH
WIDTH
HEIGHT
WEIGHT
Cgd “V” Belts 31”
19”
42.5”
145 lbs
Std “V” Belts
31”
19”
42.5”
150 lbs
LENGTH
WIDTH
HEIGHT
WEIGHT
8” Working Width will scarify approximately 175-250 square feet per hour
at Depth Per Pass 1/32”
PRODUCT NOTES:
Uses same carbide cutters as the CPM-8 Model scarifier
IDEAL FOR: Removing paint, urethane, thin-set and coatings
• Etch and/or prep the surface for new coatings
10” WALK BEHIND SCARIFIER
MODEL #
PART # POWER
HORSE POWER
PHASE
AMPS
*RPM’s BELTS
CPM-10-7.5
69200
Electric
7.5 HP, 230/460 V
Three
17.4/8.7 2344
Cgd “V” Belts 41”
23”
41”
287 lbs
CPM-10-13H
69100
Gasoline *13 HP
N/A
N/A
Cgd “V” Belts 41”
23”
41”
267 lbs
2446
PRODUCTION RATE: 10” Working Width will scarify approximately
500-700 Sq. ft. per hour at Depth Per Pass of 1/8”
PRODUCT NOTES: -6-Shaft and 8-Shaft easy change, side-loading drums
available for this heavy-duty walk-behind unit
IDEAL FOR: Aggressive removal of material • Production scarification
• Heavy coatings removal
Easy Side
Loading Drum
* RPM’s are based on the machine’s accessory speed.
* NET HORSEPOWER STATEMENT - *As rated by the engine manufacturer. The power rating of the engine indicated in this document is the net power output tested on a production engine for the engine model and measured in accordance
with SAE j1349 at 3600 rpm. Mass production engines may vary from this value. Actual power output for the engine installed in the final machine will vary depending on numerous factors, including the opening speed of the engine in
application, environmental conditions, maintenance, and other variables.
Distributed By:
One Source Equipment Rentals
www.onesourcerental.com
SCARIFIERS
SURFACE PREPARATION
10” SELF PROPELLED SCARIFIER
MODEL #
PART #
POWER
HORSE POWER
PHASE AMPS
*RPM’s BELTS
CPU-10FC-20H
73400
Gasoline
*20 HP
N/A
N/A
2122
CPU-10FC-13H
73500
Gasoline
*13 HP
N/A
N/A
CPU-10FC-10
73600-230 Electric
10 HP, 230 V
Three
CPU-10FC-10
73600-460 Electric
10 HP, 460 V
Three
LENGTH
WIDTH
HEIGHT
WEIGHT
Cgd “V” Belts 49”
24”
38.5”
530 lbs
2122
Cgd “V” Belts 49”
24”
38.5”
450 lbs
23
2179
Cgd “V” Belts 49”
24”
38.5”
530 lbs
11.5
2179
Cgd “V” Belts 49”
24”
38.5”
530 lbs
WIDTH
HEIGHT
WEIGHT
PRODUCTION RATE: 10” working width will scarify approximately 500-750 Sq. ft. per hour at Depth Per Pass of 1/8”
PRODUCT NOTES: Upcut drum rotation • Optional Outrigger Axle Assembly enables
the machine to follow slab contours closely when working on uneven surfaces or when
uniform surface removal is critica • Hydrostatic drive transmission provides a
smooth forward & reverse speed control
IDEAL FOR:
Parking deck & road repairs • Factory floor cleaning and/or preparation
• Mall floor repairs
SPECIALTY SET-UPS: Convertible hood design on CPU-10FC
model allows for
multiple drum set-ups and provides easy access for quick drum changes
12” SELF PROPELLED SCARIFIER
MODEL #
PART # POWER
HORSE POWER
PHASE
AMPS
*RPM’s BELTS
LENGTH
CPU-12-15
75600
Electric
15 HP, 230/460 V
Three
35/17.5
2100
Cgd “V” Belts 53”
36”
43”
980 lbs
CPU-12-38K
75700
Gasoline *38 HP
N/A
N/A
2100
Cgd “V” Belts 53”
36”
43”
800 lbs
PRODUCTION RATE: 12” Working Width will scarify approximately
1,250-1,500 Sq. ft. per hour at Depth Per Pass of 1/8”
PRODUCT NOTES:
Upcut drum rotation • Standard Outrigger Axle Assembly enables the
machine to follow slab contours closely when working on uneven surfaces and provide
uniform surface removal • Hydrostatic drive transmission provides a smooth forward
& reverse speed control • Cam-operated fifth wheel allows the operator to change
direction or reposition the machine while the engine is still running
IDEAL FOR: Planing concrete, asphalt and epoxies • High production use in industrial plants,
malls, dairy barns, warehouses and on roads
* RPM’s are based on the machine’s accessory speed.
* NET HORSEPOWER STATEMENT - *As rated by the engine manufacturer. The power rating of the engine indicated in this document is the net power output tested on a
production engine for the engine model and measured in accordance with SAE j1349 at 3600 rpm. Mass production engines may vary from this value. Actual power output
for the engine installed in the final machine will vary depending on numerous factors, including the opening speed of the engine in application, environmental conditions, maintenance, and other variables.
Distributed By:
One Source Equipment Rentals
www.onesourcerental.com
SELF-PROPELLED
SAWS
SCARIFIER
CUTTERS
SURFACE PREPARATION
CHANGE DRUMS IN MINUTES!
NO LONG PERIODS OF DOWNTIME!
With EDCO’s quick-change drum design and spare drum assemblies, you’ll be back
on the job in minutes. Our drum assemblies hold more cutters per loading for
added grinding action, a more uniform surface texture and fewer drum
changes. With a variety of EDCO Cutters to choose from, you can
achieve the profile, depth and speed you need for each job.
MODEL CPM-4, CPM-8, CPM-10 (8 SHAFT) CUTTERS
6 PT CARBIDE
PART # 20156
CP206-T, 1 3/4” OD
X 5/8” ID X 1/4” Thick
Tungsten Carbide
POINTED STEEL
PART # 12206
JRS-501P, 2” OD X 1/2”
ID X 3/16” Thick
18 Point Steel Cutter
FLAT TIP STEEL
PART# 20206
CP305 2” OD X 5/8” ID
X 3/16” Thick
12 Pt. Flat Tip Steel Cutter
MODEL CPM-10 (6-SHAFT) & CPU-10FC
(6-SHAFT) CUTTERS
8 PT. CARBIDE
PART# 20326
CP308T, 2 1/4” OD X 3/4” ID
X 1/4”Thick
Tungsten Carbide
POINTED STEEL
PART # 20296
CP404-P6, 2 3/8” OD X 3/4” ID
X 3/16” Thick
15 Point Steel Cutter
CPU-10FC FLAT TIP STEEL
PART # 20076
CP404, 2 3/8” OD X 1” ID
X 3/16” Thick
10 Pt. Flat Tip Steel Cutter
7 PT. MILLING
PART # 20336
CP207-T, 1 1/2” OD X 1/2” ID
X 1/2” Thick
Solid Carbide Chunker
MODEL CPL-8
(6-SHAFT) CUTTERS
6 PT. CARBIDE
PART # 20156
CP206-T, 1 3/4” OD X 5/8” ID
X 1/4” Thick
Tungsten Carbide
MODEL CPU-10, CPU-10FC (4-SHAFT) & CPU-12 CUTTERS
8 PT. CARBIDE
PART # 20136
CP408-TV, 3 1/8” OD X 1 3/16” ID
X 5/16” Thick
Tungsten Carbide
POINTED STEEL
PART # 20056
CP405-P, 3” OD X 1” ID
X 3/16” Thick
15 Point Steel CUtter
FLAT TIP STEEL
PART # 20086
CP405, 3” OD X 1” ID
X 3/16” Thick
15 Point Flat Tip Steel Cutter
1800-638-3326 • www.edcoinc.com
POINTED STEEL
PART # 20236
CP204-P, 1 5/8” OD X 1/2” ID
X 1/8” Thick
18 Point Steel Cutter
19