asahi keiki co.,ltd.

Transcription

DIGITAL PANEL METER, TRASMITTER CATALOGUE 2004
Catalogue 2004
COMPANY PROFILE
ASAHI KEIKI CO.,LTD. was established in 1950 as a
manufactuer of industrial measuring instruments.
We have since expanded into digital panel meters,
intelligent meters and bimetallic thermostats.
Rapid changes in electronic technoligy keeps us at
the forefront of these product areas.
We constantly strive to meet customer's demands for
erver higher quality and reliability.
ASAHI KEIKI CO.,LTD.
● Head
Office
:33-6, YAGUCHI 2-CHOME,
OHTA-KU,TOKYO 146-8505, JAPAN
● Telephone
:(03)3759-3893
● Fax
:(03)3757-2989
● Establishment :Sept, 1950
● Capital
:¥ 50,000,000.–
URL http://www.asahikeiki. co. jp
E-mail:dpm-overseas@asahikeiki. co. jp
SPECIAL SCALING RANGE CODE
Range
Input
Display
1V
1 to 5V
0 to (100 to 1999) one point fixed
1B
Voltage (from 0V)
1T
Voltage
±1999 to ±1999 one point fixed
2A
4 to 20mA
2B
Current (from 0mA)
2T
Current
±1999 to ±1999 one point fixed
*1V, 2A Except process monitor 1V and 2A
*Need additional cost for the above ranges
DC Voltmeter and Ammeters
AP-101
13page
A5000
15page
1/8 DIN Size
Low Cost
AP-200
AP-141
16page
1/8 DIN Size
Low Cost
18page
1/32 DIN Size
AP-201A
19page
AP-501A
AP-301
Thin case
Low Cost
25page
AH-331
31page
AP-244A
1/32 DIN Size
BCD output
1/32 DIN Size
Low Cost
26page
1/8 DIN Size
Thin case, Low cost
21page
AP-520A
28page
1/8 DIN Size
LCD, Low cost
open case
Setpoint Comparator
AM-215
35page
A5000
AM-147
1/8 DIN Size
RS-232C
1/32 DIN Size
Two setpoint
37page
AMH-762
44page
1/8 DIN Size
High Conversion
49page
1
AC Voltmeter and Ammeters
AP-166
AP-560
47page
1/8 DIN Size
Average
48page
A5000
49page
AL-512
55page
1/8 DIN Size
Process Monitor
AS-203A
AL-501A
51page
A5000
53page
1/8 DIN Size
LED, Two-wire
1/8 DIN Size
LCD, Two-wire
1/32 DIN Size
Low cost
17page
Thermo Meter
A5000
AT-205
57page
58page
1/32 DIN Size
TC, RTD
Strain Gauge
A5000
59page
ASG-251
60page
1/32 DIN Size
Universal Type
NEW
NEW
A7000 series
2
61page
A6000 series
64page
Transmitter
NEW
NEW
NEW
TZ-1X
69page
AC Power Supply
DC V,A
NEW
TZ-1B
70page
AC Power Supply
Potentiometer
TZ-1D
71page
AC Power Supply
CT
NEW
TZ-1E
72page
AC Power Supply
PT
TW-3M
74page
Programable
TZ-5H
DC V,A
84page
TZ-1F
73page
AC Power Supply
DC V,A (Small)
TW-2X
75page
2 output
TZ-41
Self power
TH-1X
79page
slim size
86page
TZ-5A
87page
RTD
3
TABLE OF CONTENT
Table of Contents..................................................................................................................4,5
Explanation..........................................................................................................................6~8
Applications ......................................................................................................................9~11
Application Examples ............................................................................................................12
DC Voltmeter & Ammeter
AP-101
3 1/2 Digit V,A ............................................................................................13
AP-102
3 1/2 Digit V,A, BCD ..................................................................................14
✽ A5000
4 Digit V, A ................................................................................................15
AP-141
4 1/2 Digit V ..............................................................................................16
AP-142
4 1/2 Digit V, BCD ......................................................................................17
AP-200
3 1/2 Digit V, 1/32 DIN ..............................................................................18
AP-201A
3 1/2 Digit V, 1/32 DIN ..............................................................................19
AP-202A
3 1/2 Digit V,A, 1/32 DIN, BCD ..................................................................20
AP-244A
4 1/2 Digit V, 1/32 DIN, BCD ......................................................................21
AP-301
3 1/2 Digit V, Thin case ..............................................................................25
AP-501A
3 1/2 Digit V, Thin case ..............................................................................26
AP-502
3 1/2 Digit V, A ..........................................................................................27
AP-520A
3 1/2 Digit V, LCD ......................................................................................28
AP-540
3 1/2 Digit V,A ............................................................................................29
AH-330, 331
3 1/2 Digit V, open case ............................................................................31
AH-381
3 1/2 Digit V, LCD, open case ..................................................................32
✽ A7000 series ..........................................................................................................................61
✽ A6000 series ..........................................................................................................................64
Comparator (Meter Relay)
AM-123
4 Digit, Two setpoint ..................................................................................33
AM-213
4 Digit, Two setpoint ..................................................................................34
AM-215
4 Digit, 1/32 DIN, Two setpoint ............................................................35,36
AM-147
4 Digit, RS-232C ..................................................................................37,38
AM-749
4 1/2 Digit, Four setpoint, RS-485, RS-232C ........................................39,40
AMH-752
3 1/2 Digit, High Conversion rate (4000/sec) ......................................41~43
AMH-762
4 Digit, High Conversion rate (4000/sec) ............................................44~46
✽ A7000 series ..........................................................................................................................61
✽ A6000 series ..........................................................................................................................64
AC Voltmeter & Ammeter
AP-166
4 Digit, Average ........................................................................................47
AP-560
3 Digit, Line Monitor ..................................................................................48
✽ A5000
4 Digit, TRUE-RMS ....................................................................................49
✽ A7000 series ..........................................................................................................................61
✽ A6000 series ..........................................................................................................................64
Process Monitor (1 to 5V, 4-20mA, etc)
AS-101
3 1/2 Digit, A,V ..........................................................................................50
AS-203A
3 1/2 Digit, A,V 1/32 DIN ............................................................................51
AS-201
3 1/2 Digit, V 1/32 DIN ..............................................................................52
AL-501A
3 1/2 Digit, A, Two-wire, LCD ....................................................................53
AL-213
3 1/2 Digit, A, Two-wire, LED, 1/32 DIN ....................................................54
AL-512
3 1/2 Digit, A, Two-wire, LED ....................................................................55
AS-243
4 Digit, A,V ................................................................................................56
✽ A7000 series ..........................................................................................................................61
✽ A6000 series ..........................................................................................................................64
4
Thermometer
✽ A5000
Sensor K,J,T,S,B,R,PT-100Ω......................................................................57
AT-205
Sensor K,J,PT-100Ω, 1/32 DIN ..................................................................58
✽ A7000 series ..........................................................................................................................61
✽ A6000 series ..........................................................................................................................64
Strain Gauge Meter
✽ A5000
4 Digit ........................................................................................................59
ASG-251
3 1/2 Digit 1/32 DIN ..................................................................................60
✽ A7000 series....................................................................................................................61~63
✽ A6000 series ..........................................................................................................................64
Transmitter
✽ TZ-1X
✽ TZ-1B
✽ TZ-1D
✽ TZ-1E
✽ TZ-1F
TW-3M
TW-2X
TW-2XA
TW-2C
TW-3R
TH-1X
TH-1C
TH-41
TH-1M
TZ-5L
TZ-5H
TZ-5X
TZ-41
TZ-5A
TZ-5B
TZ-5C
TZ-5D
TZ-5E
TZ-5F
DC V,A AC Power Supply ..........................................................................69
Potentiometer AC Power Supply ................................................................70
CT AC Power Supply ................................................................................71
PT AC Power Supply ..................................................................................72
DC V,A (Small) AC Power Supply ..............................................................73
DC V,A ......................................................................................................74
DC V,A (2 output) ......................................................................................75
DC V,A (2 output) AC Power Supply..........................................................76
TC, RTD......................................................................................................77
Alarm setter ................................................................................................78
DC V,A ......................................................................................................79
TC, RTD......................................................................................................80
Two-wire (2ch) ..........................................................................................81
DC V,A ......................................................................................................82
Distributor ..................................................................................................83
DC V,A ......................................................................................................84
DC V,A ......................................................................................................85
Two-wire ....................................................................................................86
RTD ..........................................................................................................87
Potentiometer ............................................................................................88
TC ..............................................................................................................89
AC, A ..........................................................................................................90
AC, V ..........................................................................................................91
DC, A,V ......................................................................................................92
Accessories
..............................................................................................................93,94
✽New Model
5
DIGITAL PANEL METER
EXPLANATION
7. Power Supply
OUTLINE
Digital panel meters are commonly used for various displays in a
wide range of equipment and analog-to-digital conversion in highly
advanced control systems due to recent progress in highly accurate
digital measurement.
Digital panel meters (DPMs) have wide applications and come in
various types suitable to many application specifications, and differ
from digital multi-meters (D.M.M) in that they are used especially for
single function, single range measurement.
Recently, a digital meter relay consisting of a digital panel meter
with a comparison function using digital switches has been
developed, thereby enabling not only the reading of normal values,
but also the comparison of large, medium and small values.
Recent progress in electronics, especially in transistor technology
has been remarkable, and the progressive development of ICs, LSIs
and ultra LSIs, has greatly facilitated the transmission of information
and the emergence of a highly advanced information society.
The small size and low cost of DPMs is a result of innovations in
semiconductor technology and has led to the widespread
replacement of analog indicators as part of industry's move to
automate equipment and reduce labor costs.
DPMs provide a high level of measurement accuracy impossible
with analog instruments and have an added advantage in that they
can be accurately and unambiguously read at a glance. In addition,
DPMs have a system output function which converts analog signals
from sensors to digital signals for direct input to equipment such as
computers, recorders and computing units to facilitate recording and
automatic control.
Asahi Keiki can provide a number of digital panel meters to meet a
wide range of applications through reliable design and quality control
based on long experience with digital techniques. This is supported
by extensive and rigorous past production testing which is part of our
quality-assurance control system using standards that are directly
traceable to National standards. This quality assurance system is
backed by an equally extensive and experienced after sales service.
1)
2)
3)
4)
AC 90 to 132V and 180 to 264V selectable, 50/60Hz
DC 5V ±5%, Mostly uses stabilized power
DC 24V ±10% or 20%
DC 12V ±10%
8. Input type
1) Floating input
Input terminals are all isolated from the external case, power
supply and output circuit as is most desirable for system
applications.
Photo-couplers, pulse transformers and relays are used as
isolators. In addition, this type can have a large common mode
rejection ratio (CMR). The AC power drive display only and
system application DPM (with parallel BCD output) belongs to
this type.
2) Non-floating input
2-1 Input with isolated common point
One input terminal is connected to one output terminal, but,
it is isolated from the external case and power supply.
2-2 Input with common point and one power supply terminal
One input terminal is connected to one power supply
terminal.
The DC 5V driven display-only DPM belongs to this type.
From the above different standpoints, the following types are
available.
1) Single ended input
2) Differential input
The former has 2 terminals, Hi and Lo, but the latter can
measure the signal between 2 input terminals regardless of
the voltage applied to each input terminal and the common
point, which is similar to a differential OP amplifier.
Therefore, this type completely differs from the floating input
type in that measurement is impossible if the common point
is not used, being of the 3-terminal type. This type has
large CMR to further increase the common mode rejection
effect.
9. Input impedance and bias current
METER SELECTION
1. Applications
1) For display only
For reading of general instruments
2) For control of systems provided with system BCD input.
2. Measured signals
1) Voltage/current
2) DC/AC
3. No. of display digits
Currently, 3 1/2 (1999), 4 (9999) and 4 1/2 (19999) digits are
available. Resolution defined in terms of what division in % of full
scale is necessary to be read.
For example, the resolution of a DPM displaying 1.999V is 1mV.
DPM input impedance is usually more than 100Mｽ, (excluding
DPMs with an attenuator for an input range of
more thanｱ 2V),
but this is the ratio between input voltage change and input current
change.
Current close to the constant current, called bias current, also flows
through the input circuit and therefore, if there is high resistance in
the signal source, a voltage drop is produced across the resistance
which is added to measured voltage as an error. Therefore,
attention should be paid to the bias current according to the circuit
used.
4. Measuring range
This ranges from µV minimum to V maximum as required.
For example, if the number of digits and the voltage value
corresponding to the least significant digit such as ±199.9mV or
±1.9999V are determined, the measuring range is also determined.
5. Accuracy
The maximum error guaranteed by the manufacturer is called
accracy. For example, ±0.15% rdg. ±1 digit for 3 1/2 digits or
±0.03% rdg ±1 digit for 4 1/2 digits. The latter means that the error
of thedisplayedvalue 19999 is within ±7 digits and that of the
displayed value 10000 is within ±4 digits.
6. Measuring Speed
The speed required depends on the measured object and may not
be very important when the DPM is used only for display. However,
an increase in speed in the entire measuring system results in
improved efficiency and labor savings, and it should be noted that
an increase in measuring speed reduces the time needed to
integrate (averaging) the input signal to bring about signal change
and fluctuated display with the signal change. Therefore, it is
necessary to select speed in accordance with applications.
6
DIGITAL PANEL METER
EXPLANATION
CAUTIONS
1. Prior to operating the digital panel meter, carefully read the
instruction Manual.
2. Environment where the meter is used.
1) It is desirable that meter be used under the normal room
temperature from 0 to 50｡C and relative humidity of 80% or less.
The temperature is the most important factor exerting an
influence upon meter reliability. Therefore, use the meter under
the normal room temperature as much as possible. Absolutely
avoid dew condensation caused by rapid temperature change.
2) Pay attention to not applying vibration and shock to the meter.
3) Use the meter where no dust, chemicals and gases harmful to its
electronic components exist.
3. Storage
For long storage, avoid direct rays of the sun and store in a
temperature from -10 to +70°C and relative humidity of 60% or less. It
is desirable that the meter be packaged in the same manner as that
done prior to shipment.
4. Noise
1) Power supply circuit
The digital panel meter driven by AC power may be influenced
by electric noise entering through the power line. A capacitor
for noise prevention is inserted between the line on the primary
side of a power transformer.
However, it is actually impossible to build a perfect noise
prevention circuit in such a small device as a DPM. Therefore, if
power relays, magnet switches and/or high frequency devices
are connected to the same power line and/or abnormal voltage
caused by lightning etc., may be generated in the line, externally
connect a line filter, varistor or noise absorption circuit.
2) Shield
The circuit in the digital meter is protected from electrostatic
induction by the employment of a shielded case and
electrostatic shielded terminals of the power transformer.
Therefore, if any problem occurs due to noise, connect the
common terminal E to the ground or equipment grounding
terminal.
If any problem caused buy space induction may occur, ground
the metal case. For a molded case, is it effective when it is
covered with a metal case which most be grounded.
6. Handling of system output line
1) Bundling of wires
In general, the data output from the digital meter is a T.T.L IC
with latch, and no consideration for real data transmission is paid
at all.
Since it has the signal source impedance of several K%Ω, The
proximity of large current power line, relay and magnet switch
circuits to the output line may cause a malfunction due to
electromagnetic induction caused by electrostatic induction and
magnetic field induced by surge voltage and/or current pulses.
may shorten meter life. Therefore, the output wires should be
bundled independent form other wires and to be wired apart
from the power line as much as possible.
2) Length of transmission line
The length of transmission line may have to be changed
depending on noise around the meter and surroundings.
2-1 Direct transmission of output line: 2 m or less
2-2 Transmission when a buffer circuit is used for each bit of
output line: 50 m or less
2-3 Transmission when an isolator such as a photocoupler or
mercury relay is used for each bit of output line:
500 m or less
Caution: The above lengths are only for your reference.
Therefore, the actual length must be determined
depending on each application.
5. Handling of measuring input line
The input impedance of the digital meter is very high in value of
1Mｽ to 100Mｽ so that the meter may influenced by induction noise
depending on its surroundings.
1) Use a shielded 2-Conductor wire for the input line.
2) Connect a RC filter in the input line.
However, pay attention that response time may become longer
depending on RC time constants.
7
DIGITAL PANEL METER
EXPLANATION
1. High DC voltage measurement
5. Combination with printer
When voltage exceeding the maximum voltage in the standard
range is measured (for example: more than 200 V), a multiplier is
connected externally.
When the BCD output of the digital panel meter is printed out and
recorded using digital printer.
6. Combination with recorder
When the analog output of the digital meter is recorded using a
recorder (pen writing recorder).
2. High AC voltage measurement
When voltage exceeding the maximum voltage in the standard
range is measured (for example: more than 200 V), a multiplier or
potential transformer (PT) is connected externally.
7. Combination with BCD display unit
When the BCD output of the digital panel meter is connected to a
BCD display unit for remote display.
* For the multiplier: Same as 1. High DC voltage measurement.
3. Large DC current measurement
When large DC current exceeding 2A is measured, a shunt is
connected externally.
8. Combination with converter
4. Large AC current measurement
When AC current exceeding 0.4 A to 2 A is measured, a current
transformer (CT) is connected externally.
8
When each sensor output is connected to a converter
which converts the output to 4 to 20 mA, 1 to 5 V or
any other voltage or current and also appropriate
scaling is made to the digital panel meter, the meter
widens its applications to thermometer, pressure
meter, tachometer, etc. In addition,
input isolation
and level conversion are enabled when the digital
panel meter is combined with an isolated converter.
APPLICATIONS
Measuring mixing volumes of materials
in tanks.
Detecting warping of printed circuit
boards.
The ASG-157 series digital panel meter supplies power to
load cells, subtracts tare weight and also has a built-in
output circuit, thereby enabling the measurement of weight
at low-cost.
The ASG-157 together with load cells helps you make an
appropriate mixed liquid by measuring the weight of each
of two different chemicals.
Using the 2-input (A and B channels) computing function.
The AMH-762 series digital panel meter applies analog
signals from laser displacement sensors installed above
two points on the board to its A and B channels, thereby
detecting a warp of the board by computing (A-B).
AMH-762
A5000
Measuring and evaluating press fitting
of parts used for precision machinery.
The peak hold function of the A5000 is used to check and
then evaluate parts which are press-fitted to cylinder
blocks, etc.
Helping you control rolling.
Our digital panel meters can help you control the rolling
process by, measuring the number of roller revolution and
also the moving distance of a specific roller in the vertical
direction.
The AC-963A displays the number of roller revolutions and
outputs alarm signals together with a rotary encoder
coupled to the shaft of that roller. In addition, the AM-123
inputs the output signal of an eddy current sensor to
display the moving distance of the roller and also to output
acoustic alarm signals as well as visual alarm signals with
changes in display colors.
A5000
AM-123
Measuring distortion of round bodies
and eccentricity of shaft.
Detecting, measuring and then evaluating the
length of lead wires extending from capacitors.
The peak valley hold function of the A5000
together with a laser displacement or eddy current sensor
is used to measure irregularity of round shaped bodies or
bending of shafts.
Using the 2-input (A and B channels) computing function.
The AMH-762 applies sensor detection signals to its A and
B channels.
It helps you inspect the cutting length of lead wires
extending from capacitors by using its (A—B) function.
It compares, evaluates and then outputs the computation
result at a high sampling speed of 1000 times/sec.
In addition, it can also obtain the maximum and minimum
of any computed value by using its peak hold and valley
hold functions.
A5000
AMH-762
9
APPLICATIONS
Helping you inspect the condition of
riveting, etc.
Detecting warping of door glass by a
differential transformer.
The AMH-752 can store severd/ satisfactory patterns of
riveting by using its pattern select function. It can store
eight types of high/high, high, low and low/low set points,
hysteresis values and eight types of scaling values by
using its pattern select function.
As the allowable range can be instantly changed by the
front switch or pattern selection from the rear terminal
board, the meter can be conveniently used in any line
where two or more different riveting materials exist.
A sensor power supply is built in the meter.
The AM-147, AM-749 or AM-213 has a built-in power
supply of 12V or 24V DC for an external device. Therefore,
it can be easily connected to a warping sensor with a builtin amplifier. It its direct setling function is used, it can
easily set HH, HI, Lo and LL values used for evaluating a
warp from measures data detected by the sensor.
AMH-762
AM-147
Evaluation at high speed in high-speed
mode.
Helping you process foods and control
the process.
Evaluating the clearance of piston rings at high speed.
The AMH-762 can evaluate measured data at a speed of
4000 times/sec by the successive A/D conversion method.
It can be conveniently used in any environment where
inspection time is short.
The front panel of the meter can be washed as the case is
in dust proof and waterproof construction.
The AT-216, AT-213, AC-221 and AC-281 conform to the
IP66 standard.
These meters are most suitable for use in an environment
where temperature, pressure, weight, etc. Are measured
in the HACCP process control.
AT-216
AMH-762
A5000
Outputting digital signals to peripheral
equipment.
Two or more measured values are multi
dropped by RS485.
Used as a converter with the display function which outputs
digital signals to its peripheral equipment in BCD or RC
232C. The RS232 or BCD output function can be selected
for all meters.
It our digital panel meter is used as a converter whose
signal is input to sequencers or personal computers, it can
display and check actual input parameters, therefore, it is
used conveniently for calibration.
Contributing to saving the number of output wires.
There are many digital panel meters with the output of
RS485 in the lineup.
Up to 30 meters including one host computer (31 in total)
can be connected with two signal wires used, the address
set to each meter and an RS485 - to - RW232C converter
connected. In addition. If the dedicated "DIGIPANE485"
software is used, collected data can be tabulated or
graphically displayed.
A7000
A5000
AM-749
A5000
RS485 - to - RW232C
Converter
(Commercially available)
10
APPLICATIONS
Inspecting the greased condition of
precision parts.
There meter sizes are selectable for
easily accommodating meters in racks.
Inspecting the presence or absence of grease.
The AS-105 has built-in 24V DC power supply, scaling
function and analog comparator. It can configure
inspection systems at low cost.
Din sizes of 96 mm (W) × 48 mm (H), 72mm (W) × 36 mm
(H) and 48 mm (W) × 24mm (H)
There are three meter sizes available so that any meter
size which satisfies its accommodating space is selectable
depending on the application.
In addition to these three sizes, the cases of the901 series
large display and SP-501A this type (35mm deep) digital
panel meters are designed in consideration of their
mounting environments.
A5000
Measuring large current and high voltage.
Our digital panel meter is connected to CT, PT, DC divider
or DC shunt. For example, the AP-168 for AC
measurement has its standardized CT connection ranges.
It inputs a current of 5A on the CT secondary side to
enable scaling of any current value on the primary side.
A5000
11
TRANSMITTER
APPLICATION EXAMPLES
1. ISOLATION
TRANSMITTER
TZ-1X
2. NON-ISOLATION
TRANSMITTER
TZ-5X
3. TEMP.
TRANSMITTER
TZ-5C
4. CURRENT
TRANSMITTER
TZ-5D
5. CURRENT
TRANSMITTER
TZ-5D
6. POWER
SUPPLY
TZ-5L
7. POTENTIOMETER
TRANSMITTER
TZ-5B
12
DC VOLTMETER & AMMETER
AP-101
■ Features
✽Standard 3 1/2 Digit
DC V & A
• Low Cost
• Bright LED 14.2mm (Red)
• AC180~264V, 90~132V, DC5V, DC24V
• 200mV~200V, 200µA~2A Measurement
• ±800V Measurement (option)
■ DC Voltage Measurement
AP-101-11
AP-101-12
AP-101-13
AP-101-14
±199.9mV
±1.999 V
±19.99 V
±199.9 V
Maximum
Resolution
100µV
1mV
10mV
100mV
Input
Impedance
100MΩ
100MΩ
10MΩ
10MΩ
Input
Protection
±250V
±250V
±250V
±500V
AP-101-
Power Supply
Range
Accuracy: ±0.1% rdg. ±1 digit (23°C±5°C)
■ DC Current Measurement
Range
AP-101-21
AP-101-22
AP-101-23
AP-101-24
AP-101-25
±199.9µA
±1.999mA
±19.99mA
±199.9mA
±1.999A
Maximum
Resolution
100nA
1µA
10µA
100µA
1mA
Internal
Resistance
1kΩ
100Ω
10Ω
1Ω
0.1Ω
Input
Protection
±10mA
±50mA
±150mA
±500mA
±3A
11 21
14 25
15 ±800V (Option)
■ Dimensions
96
Front
48
Model
{
{
1. AC90~132V
2. AC180~264V
3. DC5V (Isolated)
4. DC24V (Isolated)
~
Range
~
Model
■ Ordering Code
±0.3% rdg. ±1 digit only for AP-101-25
■ Specifications
73
50
6.6
Side
92 ＋0.8
−0
＋0.6
−0
Panel cut
Min.70
45
Min.120
■ Connection Diagram
COM
HOLD
START
Single Ended
50PA (Typ.)
2.5/sec
TYP.40dB (50/60Hz)
Automatic Zero Adjustment
LED. 14.2mm 3 1/2-digit
A “-” is displayed automatically
Settable to any digit position
When input exceeds the maximum display,
1999 flashes.
Power Supply:
AC90~132V
AC180~264V
DC5V±5%, 100mA (Max.)
DC24V±20%, 30mA (Max.)
Operating Temperature: 0~50°C, 35 to 85% RH
Power Consumption:
1.5VA
Dimensions:
48(H) × 96(W) × 73(D)mm DIN Size
Weight:
Approx. 150g (For AC), 85g (For DC)
Dielectric Strength:
AC type; Between input (Lo) terminal and
earth, DC500V
Between power supply terminal and
input terminal, earth, common, case,
AC1500V/1 min.
DC type; Between input (Lo) and power
supply (0V), DC±500V
Insulation Resistance:
DC500V 100MΩ at above terminals
Input Configuration:
Input Bias Current:
Conversion Rate:
Normal Mode Rejection:
Zero Stability:
Display:
Polarity:
Decimal Point:
Overrange Indication:
INPUT
HI
1
LO
2
3
4
5
6
7
8
D.P
DC POWER
103 102 101
0V ＋
9 10 11 12 13 14 15 16 17 18
13
AP-102
■ Features
✽BCD Output(Option)
DC V & A
• BCD(option)
• Bright LED 14.2mm(Red)
• AC180~264V, 90~132V, DC5V
• ±600V Measurement(option)
• BCD Open Collector available
Model
Range
AP-102-10
AP-102-11
AP-102-12
AP-102-13
AP-102-14
±19.99mV
±199.9mV
±1.999V
±19.99V
±199.9V
■ Ordering Code
Maximum
Resolution
10µV
100µV
1mV
10mV
100mV
Internal
Resistance
1kΩ
100Ω
10Ω
1Ω
0.1Ω
Input
Protection
±10mA
±50mA
±150mA
±500mA
±3A
AP-102-
{
1. None
2. BCD (TTL)
(2.5/sec)
3. BCD (Open Collector)
Output
5. None
(12.5/sec)
6. BCD (TTL)
7. BCD (Open Collector
1. AC90~132V
Power Supply 2. AC180~264V
3. DC5V (Isolated)
10 21
Range
14 25
15 ±600V(Option)
-
{
Range
AP-102-21
AP-102-22
AP-102-23
AP-102-24
AP-102-25
±199.9µA
±1.999mA
±19.99mA
±199.9mA
±1.999A
Maximum
Resolution
100nA
1µA
10µA
100µA
1mA
Accuracy:±0.2% rdg. ±1 digit(23°C±5°C)
±0.3% rdg. ±1 digit only for AP-102-25
■ Dimensions
96
Front
48
Model
{
~
Input
Protection
±250V
±250V
±250V
±250V
±500V
~
Input
Impedance
100MΩ
100MΩ
100MΩ
10MΩ
10MΩ
■ Specifications
＋0.6
92 ＋0.8
−0
Min.70
Panel cut
Panel thickness
0.8 to 5.0mm
Min.120
3
C
4
D
5
E
6
F
7
H
2
8
2
8
2
8
101
102
DC TYPE
LOWER
1
LO
2
3
4
5
6
INPUT
AC TYPE
LOWER
1
LO
2
3
9
K
4
5
6
7
8
10
L
11 12
M N
13
P
14
R
102 103
ENABLE
DP
DC5V
103 102 101
0V ＋5V
9 10 11 12 13 14 15 16 17 18
7
9 10 11 12 13 14 15 16 17 18
8
EARTH (E)
INPUT
HI
103
8
J
100 101
50-60Hz CANGE
100
D.COM
2
B
START
1
A
HOLD
1
D.COM
4
POL
1
PC
4
OVER
1
COM
HOLD
UPPER
4
HI
14
ENABLE
BCD OUT
1
COM
HOLD
Tri-state parallel BCD positive logic latch
output
Polarity signal:
“1” level at plus input
“OVER” signal:
“1” level at overflow input
Printing command signal: A positive pulse of approx 1ms at every
measurement completion
Each signal of the above: TTL level Fanout=2
*Each signal of the above can be changed to negative logic
B.C.D Output
Side
■ BCD Data Output (Isolated from input (Lo))
Measured data:
73
50
6.6
45 −0
Single Ended
50PA(Typ.)
2.5/sec or 12.5/sec(50Hz), 15/sec(60Hz)
More than 40dB(50/60Hz)
LED, 14.2mm 3 1/2 -digit
A”-” is displayed automatically
1999 or -1999 flashes.
Power Supply:
AC90~132V, AC180~264V, DC5V±5%
Operating Temperature: 0~50°C, 35 to 85%RH
Power Consumption:
1.5VA
Dimensions:
48(H) × 96(W) × 73(D)mm DIN Size
Weight:
Approx. 150g(For AC), 85g(For DC)
AC type;Between input(Lo)terminal and earth,
DC500V
Between power supply terminal and input
terminal, earth, common, case, AC1500V/
1 min.
DC type;Between input(Lo)and power
supply(0V), DC500V
Input configuration:
Input Bias Current:
Conversion Rate:
Zero Stability:
Display:
Polarity:
Decimal Point:
DP
103 102 101
AC POWER
SUPPLY
A5-
■ Features
DC V & A
• Low Cost
• Power Supply AC100~240 V
DC9~60 V
■ DC Voltage, Current
Range
Measurement Range
11
±99.99 mV
Range
12
13
14
15
Measurement Range
±999.9 mV
±9.999 V
±99.99 V
±600 V
01
02
Display
offset ±9999
full scale 0 to ±9999
Maximum Resolution
Input Impedance
Input Protection
Accuracy
10 µV
100 MΩ
±100 V
±(0.1% of FS)
Display
Maximum Resolution
10 µV
1 mV
10 mV
100 mV
Input Impedance
100 MΩ
1 MΩ
10 MΩ
10 MΩ
Input Protection
±100 V
±250 V
±250 V
±600 V
Accuracy
±(0.1% of FS)
±(0.1% of FS)
±(0.1% of FS)
±(0.15% of FS)
Maximum Resolution
1 µA
10 µA
100 µA
Input Impedance
10 Ω
1Ω
0.1 Ω
Input Protection
±100 mA
±500 mA
±3 A
Accuracy
±(0.2% of FS)
±(0.2% of FS)
±(0.3% of FS)
offset ±9999
Range Measurement Range
Display
±9.999 mA
23
03
offset ±9999
±99.99 mA
24
±999.9 mA
25
Input configuration
: Single ended
Measuring method
: ∆∑type
Normal mode rejection : More than NMR 50dB (50/60 Hz)
Caution: Range 15 UL approval guarantee up to 300VDC
■ Process
18
Range
1V
2A
Measurement Range
1 to 5 V
4 to 20 mA
Display
offset ±9999
Input Impedance
1 MΩ
10 Ω
Input Protection
±100 V
±100 mA
Accuracy
±(0.2% of FS)
±(0.2% of FS)
Input Impedance
1 MΩ
10 Ω
Input Protection
±100 V
±100 mA
Accuracy
±(0.2% of FS)
±(0.2% of FS)
■ Process with sensor power supply
Measurement Range
1 to 5 V
4 to 20 mA
Display
offset ±9999
Power supply for sensor : 12 V DC ±10% 50 mA
24 V DC ±10% 25 mA
■ Dimensions
Conversion Rate:
Maximum Display:
Zero Display:
Decimal Point:
External Control:
Operating Temperature:
Storage Temperature:
Power Supply:
Power Consumption:
Dimensions:
Weight:
Dielectric Strength (AC):
Dielectric Strength (DC):
Main display Red LED 14.2 mm height
Sub display Green LED 8 mm height
12.5 times/sec.
9999
display OL or –OL
Leading zero suppression
Start/Hold, Peak Hold, Digital Zero
0 to 50°C 35 to 85% RH
–10 to 70°C less than 60% RH
AC 100 to 240V±10% (AC main unit)
DC 9 to 60 V
(DC main unit)
Approx 4 VA (at 100 V)
96 mm × 48 mm (H) × 147.5 mm (D) DIN size
Approx. 450 g
Power supply/input terminal/output terminal
AC2000 V/1 min.
Input terminal/output terminal
DC500 V/1 min.
Case/power supply/input terminal output terminal AC2000 V/1 min.
DC500 V/1 min.
DC500 V/1 min.
DC500 V more than 100 MΩ at the above terminals
92
45
96
MIN.70
■ Ordering Code
A5
92 +0.8
-0
45 +0.6
-0
Display:
121
147.5
■ Specifications
7
Range
1V
2A
48
19
Input
01. DC voltage (±99.99 mV)
02. DC voltage (±999.9 mV to ±600 V)
03. DC current (±9.999 mA to ±999.9 mA)
18. 1-5V, 4-20mA
19. 1-5V, 4-20mA with EXC
Output 0. None
1. HI & LO setpoint
2. Analog output
3. RS-232C
4. RS-485
5. HI & LO setpoint + analog output
6. HI & LO setpoint + analog output + RS-232C
7. HI & LO setpoint + analog output + RS-485
Display 1. Single
board
2. Multiple
Main
1. AC100 - 240 V (±10%)
board
2. DC9 - 60 V
MIN.120
15
AP-141
■ Features
DC V & A
• Low Cost
• AC180~264V, 90~132V, DC5V, DC24V
• 2V~200V Measurement
• ±700V Measurement(Option)
Model
Range
AP-141-12
AP-141-13
AP-141-14
±1.9999V
±19.999V
±199.99V
■ Ordering Code
Maximum
Resolution
100µV
1mV
10mV
Input
Impedance
100MΩ
1MΩ
1MΩ
Input
Protection
±100V
±250V
±500V
AP-141-
Power Supply
Range
■ Specifications
14
15 ±700V (Option)
■ Dimensions
96
48
Front
73
50
6.6
Side
＋0.6
92 ＋0.8
−0
Min70
45 −0
Single Ended
100PA(Typ.)
2.5/sec
A "-" is displayed automatically
0000 or -0000 flashes
Power Supply:
AC90~132V
AC180~264V
DC5V±5% 150mA (Max.)
DC24V±20% 35mA (Max.)
Operating Temperature: 0~50˚C, 35 to 85%RH
Power Consumption:
2VA
Dimensions:
48(H) 96(W) 73(D)mm DIN Size
Weight:
Approx. 160g(For AC), 90g(For DC)
AC type;Between input(Lo)terminal and earth,
DC500V
terminal, earth, common, case, AC1500V/1
min.
DC type;Between input(Lo) and power
supply(0V), DC500V
Input Bias Current:
Conversion Rate:
Zero Stability:
Display:
Polarity:
Decimal Point:
12
~
Accuracy:±0.03% rdg ±1 digit (23°C±5°C)
{
{
1. AC90~132V
2. AC180~264V
3. DC5V (Isolated)
4. DC24V (Isolated)
Panel Cutout
Min120
Panel thickness 0.8 to 5.0mm
DC POWER
0V ＋
HI
3
LO
INPUT
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18
101 102 103 104
D.P
Internally Connected Lo and D. COM
16
COM
2
START
HOLD
COM
1
E
AC POWER
AP-142
■ Features
✽BCD Output (Option)
DC V & A
• BCD (Option)
• AC180~264V, 90~132V, DC5V
• 200mV~200V Measurement
• ±700V Measurement (option)
• Current Measurement (option)
• BCD Open Collector available (option)
Model
Range
AP-142-11
AP-142-12
AP-142-13
AP-142-14
±199.99mV
±1.9999V
±19.999V
±199.99V
■ Ordering Code
Maximum
Resolution
100µV
100µV
1mV
10mV
Input
Impedance
100MΩ
100MΩ
1MΩ
1MΩ
Input
Protection
±250V
±250V
±250V
±500V
AP-142-
-
Accuracy:±0.03%rdg ±1digit (23°C±5°C)
1. None
2. BCD (TTL)
3. BCD (Open Collector)
1. AC90~132V
Power Supply 2. AC180~264V
3. DC5V (Isolated)
11
■ Specifications
Range
{
{
14
15 ±700V (Option)
1D Differial input
(11, 12 range)
■ Dimensions
96
48
Front
73
50
6.6
B.C.D Output
Side
92 ＋0.8
−0
＋0.6
−0
Panel cut
Min70
45
･At Open Collector
Measured data:
Polarity signal:
“OVER” signal:
Printing command signal:
Min120
BCD OUT
1
1001 4
10 10
10
L
11 12
M N
1
A
2
B
3
C
4
D
5
E
6
F
7
H
8
J
2
8
2
8
2
8
2
8
101
100
D.COM
ENABLE
104
4 1
3
10
102
103
9
K
BCD OUT
1023
10
ENABLE
13
P
14
R
START
HOLD
D.COM
102
1 4
POL
Upper
101
1 4
PC
100
1 4
KEY
(option)
Negative logic transistor "ON" at logic "1"
Transistor "ON" at plus input
Transistor "ON" at overflow input
Transistor "ON" during a period of approx.
1ms at every measurement completion
Transistor output capacity:Applied voltage, 30V max.
(NPN)
current, 10mA max.
Saturated output voltage less than
1.2V at 10mA
･At TTL level
Measured data:
output
Polarity signal:
"1" level at plus input
"OVER" signal:
"1" level at overflow input
Printing command signal: A positive pulse of approx 1ms at every
Each signal of the above: TTL level Fanout= 2
*Each signal of the above can be changed to negative logic
OVER
■ BCD Data Output (Isolated from input (Lo))
{
~
Single Ended
100PA (Typ.)
2.5/sec
More than 50dB (50/60Hz)
LED 14.2mm 4 1/2-digit
0000 or -0000 flashes.
Power Supply:
AC90~132V
AC180~264V
DC5V ±5%, 170mA (Max.)
Power Consumption:
2VA
Dimensions:
48(H) × 96(W) × 73(D)mm DIN Size
Weight:
Approx. 190g (For AC), 125g (For DC)
AC type; Between input (Lo) terminal and
earth, DC ±500V
Between power supply terminal and
input terminal, earth, common, case,
AC1500V/1 min.
DC type; Between input (Lo) and power
supply (0V), DC ±500V
Input Bias Current:
Conversion Rate:
Zero Stability:
Display:
Polarity:
Decimal Point:
Output
DC 5V
0V ＋5V
HI
2
3
4
LO AG
INPUT
5
6
7
8
9 10 11 12 13 14 15 16 17 18
101 102 103 104
D.P
COM
1
HOLD
START
COM
Lower
E
AC POWER
17
DIGITAL PANEL METER
AP-200
■ Features
DC V & A
•Low cost
• Screw terminal
• 1/32 DIN size, Depth 39.7mm
• 200mV ~ 200V measurement
■ Dimensions
Range
Maximum
Resolution
Input
Impedance
Input
Protection
AP-200-11
AP-200-12
AP-200-13
AP-200-14
± 199.9mV
± 1.999V
± 19.99V
± 199.9V
100uV
1mV
10mV
100mV
100MΩ
100MΩ
10MΩ
10MΩ
± 100V
± 100V
± 250V
± 500V
48
Front
24
Model
Single Ended
50PA(TYP)
2.5/sec
LED, 10.16mm (Red)
Flashes 1999 or -1999
DC5V ± 5%
0~50; 35 to 85%RH
Approx 60mA (TYP)
48(W)24(H)39.7(D)mm DIN size
Approx. 30g
Between LO and case, DC1500V/min.
Between LO and case, DC500V more than 500 Ω
■ Ordering Code
AP-200-
5
7.7
4.3
Side
■ Specifications
Input Bias:
Conversion Rate:
Display:
Polarity:
Decimal point:
Power Supply:
Power Consumption:
Dimensions:
Weight:
10.16
Accuracy: ±(0.1% of rdg 1 digit) (23; ± 5;, 35to85%RH)
Stability max 2 digit for only AP-200-11
39.7
Back
Panel cutout
45 ＋0.6
−0
＋0.3
22.2 −0
Range
65mm
1 2 3 4 5
Terminal No.
1
2
3
4
5
18
Description
Input HI
Input LO
HOLD
Power supply 0V
Power supply +5V
35mm
AP-201A
■ Features
DC V & A
• Low Cost
• DC5V(Non-Isolated)
Range
AP-201A-11
AP-201A-12
AP-201A-13
AP-201A-14
±199.9mV
±1.999V
±19.99V
±199.9V
Maximum
Resolution
100µV
1mV
10mV
100mV
Input
Impedance
100MΩ
100MΩ
10MΩ
10MΩ
Input
Protection
±100V
±100V
±250V
±500V
AP-201A-
Range
{
11
~
Model
■ Ordering Code
14
Accuracy:±0.1% rdg. ±1 digit (23°C5°C) Stability Max. 2 digits for only AP-201A-11
■ Dimensions
48
Front
73
4.8
51
Side
＋0.6
45 −0
Min.35
22.2−0
＋0.3
Single Ended.
50PA(Typ.)
2.5/sec
40dB(Typ.)(50/60Hz)
Flashes 1 or -1 of the most significant digit for
an input signal exceeding the maximum
display range.
Power Supply:
DC5V±5%, 60mA
Power Consumption:
Approx. 60mA
Dimensions:
24(H) × 48(W) × 73(D)mm DIN Size
Weight:
Approx. 40g
Between input(Lo) terminal and mounted plate.
AC1500V/1 min.
Panel cut
Min.65
1
2
HI
LO
3
4
101
INPUT
5
6
7
COM
Operable only when
input Lo and power supply
(0V) are extermally connected
HOLD
Input Bias Current:
Conversion Rate:
Zero Stability:
Display:
Polarity:
Decimal Point:
24
■ Specifications
3
102 10 0V ＋5V
D.P
8
9
10
POWER
19
AP-202A
■ Features
✽ISOLATED Power Supply
DC V & A
• BCD (option)
• DC5V, DC12V, DC24V (Isolated)
• Conversion Rate 2.5/sec or 12.5/sec (50Hz),
15/sec (60Hz)
■ Ordering Code
Model
Range
AP-202A-11
AP-202A-12
AP-202A-13
AP-202A-14
±199.9mV
±1.999V
±19.99V
±199.9V
Maximum
Resolution
100µV
1mV
10mV
100mV
Input
Impedance
100MΩ
100MΩ
10MΩ
10MΩ
Input
Protection
±100V
±100V
±250V
±500V
AP-202A-
-
-
{
Output
Accuracy: ±0.1% rdg. ±1 digit (23°C ±5°C)
AP-202A-21
AP-202A-22
AP-202A-23
AP-202A-24
AP-202A-25
±199.9µA
±1.999mA
±19.99mA
±199.9mA
±1.999A
Maximum
Resolution
100nA
1µA
10µA
100µA
1mA
Input
Resistance
1kΩ
100Ω
10Ω
*1Ω
*0.1Ω
Input
Protection
±10mA
±50mA
±150mA
±500mA
±3A
Power Supply
{
3. DC5V (Isolated)
4. DC24V (Isolated)
5. DC12V (Isolated)
{
11
21
Range
~
Range
{
~
Model
1. None
2. TTL
3. Open Collector
1. None
2. BCD (2.5/sec)
6. BCD (12.5/sec 50Hz)
7. BCD (15/sec 60Hz)
BCD Out
14
25
■ Dimensions
48
Front
73
4.8
51
B.C.D Output
(option)
Side
45 ＋0.6
−0
Min.35
Single Ended
50PA (Typ.)
2.5/sec or 12.5/sec (50Hz), 15/sec (60Hz)
40dB (Typ.) (50/60Hz)
LED, 10.2mm 3 1/2-digit
1999 flashes.
Power Supply:
DC5V ±5%, 120mA
DC12V ±20%, 50mA
DC24V ±20%, 25mA
Power Consumption:
650 mW
Dimensions:
24(H) × 48(W) × 73(D)mm DIN Size
Weight:
Approx. 50g
Between Input (Lo) terminal and power supply
(0V), DC ±500V
Between power supply terminal and case,
AC1500V/1 min.
22.2 ＋0.3
−0
■ Specifications
Input Bias Current:
Conversion Rate:
Zero Stability:
Display:
Polarity:
Decimal Point:
24
±0.3% rdg. ±1 digit only for AP-202A-25
* These resistors are connected to the outside of the unit.
Panel cut
Min.65
9
10
11
12
2
8
2
8
2
8
101
13
14
15 17
16 18
19 21
20 22
102
COM
7
8
23
24
HI
LO
INPUT
20
3
4
101
5
6
7
COM
2
BLANKING
1
HOLD
BCD OUT
Lower
3
102 10 0V
D.P
8
9
25
26
COM
5
6
POL
3
4
103
1
PC
1
2
100
102
4
HOLD
1
OVER
Upper
101
1 4
ENABLE
BCD OUT
100
1 4
10
＋
POWER
AP-244A
■ Features
✽BCD Output(Option)
DC V & A
• 5V, 24VDC(Isolated)
• Bright LED, 8mm(Red)
• 2V to 200V Measurement
• BCD Output(option)
Range
AP-244A-11
AP-244A-12
AP-244A-13
AP-244A-14
±199.99mV
±1.9999V
±19.999V
±199.99V
Maximum
Resolution
10µV
100µV
1mV
10mV
Input
Impedance
100MΩ
100MΩ
1MΩ
1MΩ
Input
Protection
±100V
±100V
±250V
±250V
48
Front
24
Model
■ Dimensions
Accuracy:±0.03% rdg ±1 digit (23°C±5°C)
■ Specifications
Dimensions:
Weight:
5
65
Side
45 ＋0.6
−0
Min.35
Power Supply:
Operating Temp.:
Power Consumption:
B.C.D (option)
87 ±1
22.2 ＋0.3
−0
Single ended
100PA(Typ.)
2.5/sec, 12.5(50Hz), 15(60Hz)/sec
NMR50dB(50/60Hz)
LED 8mm 4 1/2 digit
0000 flashes
5VDC±5%, 24VDC±20%
0~50˚C, 35 to 85%RH
120mA at 5VDC(Max.)
30mA at 24VDC(Max.)
24(H) 48(W) 87(D)mm Din size
50g
Between input(Lo)terminal and mounted plate,
AC1500V/1 min.
Between input(Lo)terminal and power
supply(0V), 500VDC/1 min.
Input Bias Current:
Conversion Rate:
Display:
Polarity:
Decimal Point:
Panel Cutout
Min.65
■ BCD Data Output(Isolated from input(Lo))
POL
ENABLE
COM
BCD OUT
11
13 15
17
19
21 23
25
8
10 12
14 16
18 20
22 24
26
8
2
2
8
OVER
6
7
100
1 4
101
1 4
1
1
5
9
3
7
Type of BCD
{
1. none
2. TTL
3. Open collector
Output
{
1. none
2. BCD(2.5/sec)
6. BCD(12.5/sec)
7. BCD(15/sec)
Power Supply
{ 3.4. 512toto12VDC
24VDC
4
6
8
2
1
0
10
10
{
8
2
3
10
10
COM
2
BCD OUT
1
2
HI
LO
3
4
5
8
9
Lower
3
4
2
101 10 10 10 0V
D.P
10
＋
POWER
11 1V
~
Range
103 104
4 1
HOLD
2
■ Ordering Code
-
1
Upper
INPUT
AP-244A-
102
4
PC
Negative logic transistor "ON" at logic "1"
Transistor "ON" at plus input
Transistor "ON" during a period of approx. 100
to 200ms at every measurement completion
Transistor output capacity: Applied voltage, 30V max
current, 10mA max
Saturated output voltage less than 1.2V at
10mA
•AT TTL level
Measured date:
output
Polarity signal:
"1" level at plus input
"OVER" signal:
"1" level at overflow input
Printing command signal: A positive pulse of approx 100 to 200ms at
every measurement completion
Each signal of the above: TTL level Fanout=2
* Each signal of the above can be changed to negative logic
COM
START
HOLD
•At Open collector
Measured data:
Polarity signal:
"OVER" signal:
14 2A
21
MEMO
22
MEMO
23
MEMO
24
AP-301
■ Features
✽Compact Size, 14.2mm LED
DC V & A
• Compact Size, 36(H) × 72(W) × 29(D)mm
• Bright LED, 14.2mm (Red)
• Isolated DC24V Available (Option A or D)
Model
Range
AP-301-11
AP-301-12
AP-301-13
AP-301-14
±199.9mV
±1.999V
±19.99V
±199.9V
■ Ordering Code
Maximum
Resolution
100µV
1mV
10mV
100mV
Input
Impedance
100MΩ
100MΩ
10MΩ
10MΩ
Input
Protection
±100V
±100V
±250V
±500V
AP-301-
A. Screw Terminal, 4-20 mA
(Range code 11)
B. Screw Terminal, Scaling
(Range code 11-14)
C. Screw Terminal, Range Select
(Range code 12-14)
D. Screw Terminal, DC-DC
Isolated power supply(5V DC)
∗BLANK-None
Option
■ Specifications
Range
{
11 1V
~
14
■ Dimensions
72
Front
36
Single Ended
50PA (Typ.)
2.5/sec
40dB (Typ.) (50/60Hz)
1999 flashes
Power Supply:
DC5V ±5%, 80mA (Max.)
Power Consumption:
400mW
Dimensions:
36(H) × 72(W) × 29(D)mm DIN Size
Weight:
Approx. 35g
Between input (Lo) terminal and case,
AC1500V/1 min.
Between input (Lo) terminal and power supply
(0V), DC500V
4.8
29
16.3
Side
＋0.6
68 ＋0.7
−0
Min.58
33 −0
Input Bias Current:
Conversion Rate:
Zero Stability:
Display:
Polarity:
Decimal Point:
Panel cut
Min.96
1
HI
2
LO
3
BLANKING
INPUT
Operate only when input
Lo is externally
connected to power (0V)
4
HOLD
5
103
6
102
7
10
1
8
0V
9
＋5V
D.P
POWER
25
AP-501A
■ Features
✽Super Thin Case, Low Cost
DC V & A
• Low Cost
• Bright LED, 14.2mm (Red)
• Thin Case (Depth 34.5mm)
Range
AP-501A-11
AP-501A-12
AP-501A-13
AP-501A-14
±199.9mV
±1.999V
±19.99V
±199.9V
Maximum
Resolution
100µV
1mV
10mV
100mV
Input
Impedance
100MΩ
100MΩ
10MΩ
10MΩ
Input
Protection
±100V
±100V
±250V
±500V
AP-501A-
Range
{
11
~
Model
■ Ordering Code
14
■ Dimensions
■ Specifications
96
Differential (11/12-range), Single Ended
(13/14-range)
Input Bias Current:
50PA (Typ.)
Conversion Rate:
2.5/sec
Normal Mode Rejection: 40dB (Typ.) (50/60Hz)
Zero Stability:
Display:
Polarity:
Decimal Point:
Display 1 or -1 of the most significant digit for
display range.
Power Supply:
DC5V ±5%, 120mA
Power Consumption:
Approx. 120mA
Dimensions:
48(H) × 96(W) × 34.5(D)mm DIN Size
Weight:
Approx. 50g
Between input (Lo) terminal and mounted
plate. AC1500V/1 min.
Front
48
34.5
12.2
6.3
Side
Min.70
45
＋0.6
−0
92 ＋0.8
−0
Panel cut
Min.120
When use single ended, connect terminal ② and ③
(COMMON and 0V Terminal is internally connected)
LO
INPUT
26
4
COM
HI
3
5
HOLD
2
ANALOG・G
1
6
7
8
9
10
2
103 10 101 0V ＋5V
D.P
POWER
AP-502
■ Features
✽ISOLATED Power Supply
DC V & A
• Low Cost
• Serial Data Output
• Thin Case(Depth 32mm)
• DC5V(Isolated)
• 200mV~200V, 200A~2A Measurement
AP-502-11
AP-502-12
AP-502-13
AP-502-14
±199.9mV
±1.999V
±19.99V
±199.9V
Maximum
Resolution
100µV
1mV
10mV
100mV
Input
Impedance
100MΩ
100MΩ
10MΩ
10MΩ
Input
Protection
±250V
±250V
±250V
±500V
Input
Resistance
1KΩ
100Ω
10Ω
1Ω
0.1Ω
Input
Protection
±10mA
±50mA
±150mA
±500mA
±3A
Range
{
11 21 1V
~
Range
~
Model
■ Ordering Code
AP-502-
14 25 2A
Accuracy: ±0.1% rdg. ± 1 digit(23˚C±5˚C)
Range
AP-502-21
AP-502-22
AP-502-23
AP-502-24
AP-502-25
±199.9µA
±1.999mA
±19.99mA
±199.9mA
±1.999A
Maximum
Resolution
100nA
1µA
10µA
100µA
1mA
Accuracy: ±0.2% rdg.±1 digit(23˚C±5˚C)
±0.3% rdg.±1 digit only for AP-502-25
■ Dimensions
96
Front
48
Model
■ Specifications
32
12.2
6.3
Side
＋0.6
92 ＋0.8
−0
Min.70
45 −0
Single Ended
50PA(Typ.)
2.5/sec
1999 flashes.
Power Supply:
DC5V±5%, 120mA(Max.)
Power Consumption:
Approx. 120mA
Dimensions:
48(H) 96(W) 32(D)mm DIN Size
Weight:
Approx. 60g
Between input(Lo)terminal and power
supply(0V), DC500V.
Between input(Lo)terminal and mounted plate.
AC1500V/1 min.
Input Bias Current:
Conversion Rate:
Zero Stability:
Display:
Polarity:
Decimal Point:
Panel Cutout
Min.120
1
2
HI
3
4
5
6
LO
IN PUT
7
STB
COM COM
8
9
SOUT
PC
HOLD
10 11 12 13 14 15
2
103 10
D.P
101
0V
＋5V
POWER
ISERIAL DATA OUT
27
AP-520A
■ Features
✽LCD Display
DC V & A
• LCD, 12.7mm
• Thin Case (Depth 34.5mm)
Range
AP-520-11
AP-520-12
AP-520-13
AP-520-14
±199.9mV
±1.999V
±19.99V
±199.9V
Maximum
Resolution
100µV
1mV
10mV
100mV
Input
Impedance
100MΩ
100MΩ
10MΩ
10MΩ
Input
Protection
±100V
±100V
±250V
±500V
AP-520-
{
Range
14
■ Dimensions
■ Specifications
Differential (11/12-range)
Single Ended (13/14-range)
Input Bias Current:
50PA (Max.)
Conversion Rate:
2.5/sec
Normal Mode Rejection: 40dB (Typ.) 50/60Hz
Zero Stability:
Automatic zero adjustment
Display:
LCD, 12.7mm 3 1/2-digit
Polarity:
Decimal Point:
Display 1 or -1 of the most significant digit for
display range.
Power Supply:
DC5V ±5%
Power Consumption:
Approx. 15mW
Dimensions:
48(H) × 96(W) × 34.5(D)mm DIN Size
Weight:
Approx. 60g
Between input terminal (Lo) and mounting
panel DC500V.
11
~
Model
■ Ordering Code
96
48
Front
34.5
12.2
6.3
Side
Min.70
45
＋0.6
−0
92 ＋0.8
−0
Panel cut
Min.120
When use single ended, connect terminal ② and ③
(COMMON and 0V Terminal is internally connected)
LO
INPUT
28
4
COM
HI
3
5
HOLD
2
ANALOG・G
1
6
7
8
9
10
2
103 10 101 0V ＋5V
DECIMAL
POINT
POWER
AP-540
■ Features
DC V & A
• Bright LED, 14.2 mm (Red)
• Thin Case (Depth 34.5 mm)
• Power supply DC 5V (Non-isolated)
• 200 mV∼200 V measurement
■ Dimensions
Maximum
Input
Resolution
Impedance
±199.99mV
AP-540-11
10µV
100MΩ
±1.9999V
AP-540-12
100µV
100MΩ
±19.999V
AP-540-13
1mV
1MΩ
±199.99V
AP-540-14
10mV
1MΩ
Accuracy:±(0.03% of rdg +1 digit ) (23°C±5°C 45~75%RH)
Model
Range
Input
Protection
±100V
±100V
±250V
±500V
96
Front
48
■ Specifications
Start:
Decimal point:
Operating temperature:
Power supply:
Power consumption:
Dimensions:
Weight (unit):
Dielectric strength:
Insulation resistance:
Accessory:
■ Ordering Code
34.5
6.3
12.2
Side
92+0.8
-0
Panel cut
Min.70
Display:
Polarity:
Hold:
Single ended
100 pA (TYP.)
2.5/sec
More than NMR50dB (50/60 Hz)
19999
0000 flashes
LED, 14.2 mm (Red)
START/HOLD terminal and 0 V shorted or level
"0"
START/HOLD terminal and 0 V open or level
"1"
0~50°C 35~85%RH
DC 5 V±5%
75 mA (Max.)
48(H) × 96(W) × 34.5(D)mm DIN size
Approx. 60 g
Between LO and case, AC 1500 V/l min.
More than DC 500 V 100 MΩ at the above
terminals
Connector, instruction manual
45 +0.9
-0
Input bias current:
Conversion rate:
Normal mode rejection:
Maximum display:
Overrange indication:
Min.120
AP-540-
11
Range 12
13
14
{
1
2
3
HI
L0
NC
4
5
7
8
9
10
104 103 102 101
0V +5V
D.P
DC POWER
INPUT START/HOLD
6
29
MEMO
30
OPEN CASE METER
AH-330, 331
■ Features
✽EASY Installation
DC V & A
• Uncased, 3 digits(AH-330) 3 1/2 digits(AH-331)
• Bright LED, 14.2mm(Red)
• Hold for AH-331(option)
• Power Supply DC5V±5%
(AH-331)
Input
Protection
±100V
±100V
±100V
±100V
AH-330
4.2
Parts
Accuracy: ±0.1% rdg.±1 digit(23˚C±5˚C)
12.47 12.47 12.47
3.1
000000000
8
2.54
NO.1
POL
17.78
＊B
DP2 DP1
59
0.64
11
23
29.5
OVF
4-2.8φ
65
（mm）
AH-331
4.2
Option
Parts
8.54
2
2.54
Single Ended
50PA(Typ.)
2.5/sec
40dB(Typ.)
LED, 14.2mm
lights up "OVER" LED(AH-330)or 1999
flashes(AH-331)
Power Supply:
DC5V±5%
Power Consumption:
AH-330 75mA, AH-331 80mA
Dimensions:
29.5(H) 65(W) 18.2(D)mm
Weight:
Approx. 20g
14.2
20
2.25
10.5 12.75
■ Specifications
000000000
14.2
000000000
8
＊A
25
25
10.5 14.5
NO.1
Range
{
11
17.78
19
＊B
0.64
DP1
4-2.8φ
65
Option
NO.8
（mm）
~
AH-330331
8
DP3 DP2
59
5.5
■ Ordering Code
23
29.5
2.54
Input Bias Current:
Conversion Rate:
Zero Stability:
Display:
Polarity:
Decimal Point:
000000000
＊A
19
±99.9mV
±0.999V
±199.9mV
±1.999V
Input
Impedance
100MΩ
100MΩ
100MΩ
100MΩ
1.6
AH-330-11
AH-330-12
AH-331-11
AH-331-12
Maximum
Resolution
100µV
1mV
100µV
1mV
1.6
Range
8.54
Model
■ Dimensions
2.54
12
AH-330
AH-331
1
HI
1
HI
2
LO
2
LO
3
HOLD
3
101
4
102
5
103
INPUT
1
4
10
5
102
6
0V
7
+5V
D.P
POWER
6
0V
7
＋5V
INPUT
D.P
POWER
OPTION
8
COM
9
HOLD
31
OPEN CASE METER
AH-381
■ Features
✽LCD Display
DC V & A
• LCD, 10.2mm
• Engineering units available
• Power supply 5V DC±5%
Model
Range
AH-381-11
AH-381-12
±199.9mV
±1.999V
■ Ordering Code
Maximum
Resolution
100µV
1mV
Input
Impedance
100MΩ
100MΩ
Input
Protection
±100V
±100V
AH-381Range
{ 11
12
Accuracy: 0.1% rdg.±1 digit(23°C±5°C)
■ Dimensions
mVA℃
AC
MkΩ
25
59
64.5
29.5
パーツ
1.6
6.1+0.3
8.54
4.2
0.64
24.1
P-2.54×6
17.78
50.8
1
HI
2
LO
INPUT
3
4
HOLD
5
COM
6
0V
7
＋5V
POWER
32
10.2
DC
2.8 2.8
23
12
4-2.8φ
29.5
Single Ended
100PA(Typ.)
2.5/sec
40dB(Typ.)
LCD, 10.2mm
display 1 or -1 of the most significant digit
Power Supply:
DC5V±5%
Power Consumption:
3mA(Max.)
Dimensions:
29.5(H) × 65(W) × 16.5(D)mm
Weight:
Approx. 17g
Input Bias Current:
Conversion Rate:
Zero Stability:
Display:
Polarity:
Decimal Point:
2.54
■ Specifications
SETPOINT COMPARATOR
AM-123
■ Features
• Three colour display(red, green, amber)
• Two-setpoint(Hi & Lo)
• Digital Zero, Peak Hold(option)
Comparator
Model
AM-123-11
AM-123-12
AM-123-13
AM-123-14
AM-123-1V
Range
± 99.99mV
± 999.9mV
± 9.999V
± 99.99V
1-5 V
Display
Input Impedance Input Protection
100MΩ
100MΩ
Offset ± 9999
1MΩ
± 250V
Fullscale ± 9999
1MΩ
1MΩ
■ Ordering Code
AM-123-1
Accuracy: (0.3% of rdg 2 digit) (23˚C5˚C 35 to 85%RH)
Range
■ Dimensions
Display
Range
Internal Resistance Input Protection
± 999.9µA
100Ω
± 50mA
± 9.999mA
10Ω
± 150mA
Offset ± 9999
± 99.99mA
1Ω
± 500mA
Fullscale ± 9999
± 999.9mA
0.1Ω
± 3A
4-20mA
51Ω
± 70mA
96
Front
48
Model
AM-123-22
AM-123-23
AM-123-24
AM-123-25
AM-123-2A
{ 1.2. Relay
Photocoupler
Comparator output
Accuracy: (0.1% of rdg 2 digit) (23˚C5˚C 35 to 85%RH)
(0.3% of rdg 2 digit) for 25 range
■ Specifications
Dielectric Noise:
Accessories:
Compare Control System:
Setting Range:
Comparative Condition:
Relay Contact Capacity:
Photocoupler Capacity:
Hysteresis:
92 ＋0.8
−0
Panel cutout
Min.70
Maximum Display:
Decimal Point:
Zero Display:
External Control:
Memory Backup:
Power Supply:
Power Consumption:
Dimensions:
Weight:
＋0.6
Polarity:
Single Ended
12.5/sec(50Hz), 15/sec(60Hz)
NMR50dB or more(50/60Hz)
LED, main display 14.2mm
sub display 8mm
display OL or -OL
±9999
Hold, Start, Digital Zero, Peak, Peak-valley, Valley
EEPROM
0~50˚C, 35 to 85%RH
AC90~264V(50/60Hz)
4VA(TYP)(At AC100V)
48(H) 96(W) 98(D)mm DIN size
Approx 280g
Between input/compare output DC500V/1 min
Between power supply and input, case, compare
output
AC2100V/1 min
DC500V 100MΩ or more at above terminals
Power supply normal/common mode ±1500V
Instruction manual, unit label, terminal cover
Microcomputer
-9999~0~+9999
High setpoint < Indication / HI
High setpoint > Indication > Low setpoint / GO
Low setpoint > Indicatyion / LO
AC125V 0.5A Resistive load
DC28V 1A Resistive load
Voltage MAX. 30V
Current MAX. 50mA
Saturation voltage less than 1, 2V at 50mA
1 to 999 digit at each setpoints
89
45 −0
Conversion Rate:
Display:
9
Side
Panel thickness 0.8 to 5mm
Upper terminal
HI
a
c
GO
b
a
c
LO
b
a
c
b
① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨
(c)
(e)
(c)
(e)
(c)
(e)
( )：PHOTO COUPLER
Lower terminal
① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨
HI
LO COM S/H
DZ
PH
NC
POWER
33
SETPOINT COMPARATOR
AM-213
■ Features
• NEMA 4 front panel (IP66)
• Excitation power supply DC24V
• Analog output (4 to 20mA) option
• HI and LO setpoints
Comparator
• 1/32 DIN size
Model
Range
Display
100MΩ
± 250V
AM-213-11 ± 99.99mV
100MΩ
± 250V
AM-213-12 ± 999.9mV
OFFSET ± 9999
1MΩ
± 250V
AM-213-13 ± 9.999V FULLSCALE ± 9999
1MΩ
± 250V
AM-213-1V 1 to 5 V
■ Ordering Code
AM-213 -
Comparator output
Accuracy : ± (0.03% of rdg +2 digit) (23°C ± 5°C 35 to 85%RH)
Analog output
Model
Range
Display
OFFSET ± 9999
50Ω
± 60mA
AM-213-2A 4 to 20mA
FULLSCALE ± 9999
Accuracy : ± (0.1% of rdg +2 digit) (23°C ± 5°C 35 to 85%RH)
※Accuracy is less than 1 (FSC-OFC) / (FIN-OIN)
■ Specifications
{1.2. Relay
Photocoupler
{1.3. None
4 to 20mA
11. ± 99.99mV
12. ± 999.9mV
Input code 13. ± 9.999V
1V. 1 to 5V
2A. 4 to 20mA
{
■ Dimensions
48
●Measuring Section
Maximum display:
Decimal point:
Zero display:
HI LO
24
Front
E
M
▲
88
22
Overrange warning:
Single ended
12.5 times/sec(50Hz),15 times/sec(60Hz)
NMR50dB or more (50/60Hz)
Red LED, 8mm height
Automatic “-” display when the computation
result is minus
display OL or -OL
± 9999
▲
Conversion rate:
Noise rejection ratio:
Display:
Polarity display:
Side
●Common Section
Excitation supply:
Accessories:
●Analog Output (isolated input LO)
Range
11.5
＋0.6
Display
OFFSET ± 9999
50Ω
± 60mA
AM-213-2A 4 to 20mA
FULLSCALE ± 9999
＋0.3
Panel cut
MIN 65
INPUT
Can adjust analog output to meet display.
※Ripple for resistive load 250Ω, 20mA
45.0 −0
■ Output Specification
Model
6.5
22.2 −0
EEPROM (rewrite 100,000 times)
0 to 50°C 35 to 85%RH
-10 to 70°C (less than 60%RH)
DC24V ± 20%
85mA (TYP) at DC24V
48mm(W) × 24mm(H) × 388mm(D)
approx.100g (unit only)
Input terminal (LO) and comparator output,
ANALOG (-), DC500V/min.
Power supply (OV) and input (LO), comparator
output, ANALOG (-), case, DC500V/min.
Input terminal (LO) and case AC1500V/min.
DC500V more than 100MΩ at the above terminals
DC24V ± 10% 25mA ripple less than 200mVp-p
Instruction manual, rubber paking, terminal
MIN 35
Memory backup:
Operating temp.:
Storage temp.:
Power supply:
Power consumption:
Dimensions:
Weight:
HI
LO
EXC
ANALOG
OUT
0V +24V ＋
−
HI
a
COM LO
c
a
DC POWER
0V +24V
①②③④⑤⑥⑦⑧⑨⑩⑪
c
34
e
c
SETPOINT COMPARATOR
AM-215
■ Featuers
• HI and LO set-point
• Bright LED 8mm (Red)
• 1 to 5V, 4 to 20mA Measurement
• Power Supply DC24V ±20% (Isolated)
• Offset +/–9999 adjustable
■ DC Voltage Meaurement
Model
Range
AM-215-11
AM-215-12
AM-215-13
AM-215-1V
±99.99mV
±999.9mV
±9.999V
1 to 5V
● Excition power supply section
Excition power supply:
DC24C ±5%, 25mA
Display
Adjustable
Offset
±9999
Fullscale
±9999
Input
Impedance
100M ohm
100M ohm
1M ohm
1M ohm
Input
Protection
±100V
±100V
±250V
±250V
Accuracy: ±0.03% rdg. ±2 digit (23˚C±5˚C)
Range
AM-215-2A
4 to 20mA
Display
Adjustable
Offset
±9999
Fullscale
±9999
Input
Impedance
Input
Protection
50 ohm
±60mA
Accuracy: ±0.1% rdg. ±2 digit (23˚C±5˚C)
■ Specifications
● Measurement section
Operation method:
Input Bias Current:
Conversion rate:
Display:
Polarity:
Maximum display:
Decimal point:
Zero display:
Single ended
Dual slope
50PA (Typ.)
Max. 12.5/sec. (50Hz) or 15/sec. (60Hz)
LED, 8mm (Red), 4 digits
oL or –oL flashes
±9999 (4 digit)
Settable at any position (By pressing sheet
switch)
Reading “zero” suppression
● Comparison section
Control method:
Computation by microcomputer
Setting range:
–9999 to 9999
Conparison condition:
Measured value > High limit set-value – HI
Low limit set value Measured value High limit set value – GO
Low limit set value > Measured value – LO
Setting condition:
Low limit set value < High limit set value
Hysteresis:
1 to 999 digit for each set point
Relay contact capacity:
DC24V resistive road
● External control section
Digital zero:
● Analog output section (impossible both of Analog output and
RS-485 selected)
Output function:
DC4 to 20mA or DC0 to 10V
Output specification
Type
4 to 20mA
0 to 10V
Model
Comparator
• Fullscale +/–9999 adjustable
Risistive load
0 to 250 ohm
More than 10K ohm
Ripple
Less than 25mVp-p
Less than 50mVp-p
● RS-485 output section (impossible both of Analog output and
RS-485 selected)
Synchronous method:
Start and stop
Communication method:
2-wire system half duplex
(Polling and selecting)
Transmission speed:
19200bps/9600bps/4800bps/2400
bps
Start bit:
1 bit
Data length:
7 bit
Error detection:
Even parity (BCC)
Stop bit:
2 bit
Character code:
ASCII code
Transmission control:
No protocol
Signal name used:
Non-reversible output (+),
Reversible (–)
No. of connectable meters: Up to 31 meters
Line of length:
Up to 500m in total
■ Common Specifications
Memory backup:
Storage temperature:
Power supply:
Power consumption:
Dimensions:
Weight:
Dielectic strengh:
Short DZ terminal and COM terminal or level
“0”.
Then digital zero “ON”.
Accracy
±(0.5% of FS)
±(0.5% of FS)
Accessories:
0 to 50˚C, 35 to 85%RH
–20 to 70˚C, less than 60%HH
DC24V ±20%
Approx. 4W
24(H) 48(W) 87.5(D) DIN size
Approx. 100g
Between power supply (0V), input
terminal and each output terminal
DC500V/1 min.
Between input terminal and each
output terminal DC500V/1 min.
Between case, power supply, input
terminal and each output terminal
DC500V/1 min.
DC500V more than 100M ohm at
above terminals.
Instruction manual, setting
procedure
35
SETPOINT COMPARATOR
AM-215
■ Panel Cut Out
+0.6
45.0 -0
LO
(e)
(c)
(e)
(c)
0V
COM
a
c
a
c
a
(e)
c
10
11
12
13
14
15
16
17
18
MIN 35
Comparator
(c)
+24V
+0.3
EXC
GO
22.2 -0
HI
POWER !
1
2
3
4
HI
LO
+
-
INPUT
5
ANALOGO
UT or
RS485
6
TERMINATOR
7
8
9
DZ
0V
+V
MIN 65
POWER
■ Ordering Code
AM-215-
■ Dimensions
Comparater output
1.
2.
Relay
Photo coupler
Option output
1.
4.
6.
7.
None
RS-485
Analog output (4-20mA)
Analog putput (0-10V)
11.
12.
13.
1V.
2A.
11 range (±99.99mV)
12 range (±999.9mV)
13 range (±9.999V)
1V range (1-5V)
2A range (4-20mA)
48.0
Input range
24.0
HI LO
E
3.5
36
M
84.3
SETPOINT COMPARATOR
AM-147
■ Features
✽ RS232C output
• Conversion rate 12.5times/sec(50Hz) or
15times/sec(60Hz)
• Four setpoint(Can display two setpoint)
• Maltiple range
• Scaling value and setting value stored 8 pattern
Comparator
• Peak hold, Valley hold, Peak-valley hold, Digital zero,
Moving average(standard)
• Power supply for sensor 24VDC 40mA
• Direct setting function
• Power supply 90 to 264VAC
Measuring
Range
±99.9mV
±999.9V
±9.999V
±99.99V
±700.0V
1 to 5V
Input Range
DV
11
12
13
14
15
IV
Comparison condition:
Display
Adjustable
Offset
±9999
Fullscale
±0 to 9999
Input
Impedance
100MΩ
100MΩ
1MΩ
10MΩ
10MΩ
1MΩ
Input
Protection
±250V
±250V
±250V
±500V
±700V
±250V
Comparison condition
High high limit set value Measured value
High limit set value Measured value
High high limit set value
Low low limit set value
Measured value High limit set value
Low limit set value
Measured value Low limit set value
Measured value Low low limit set value
Comparison relay output:
Accuracy: ±(0.03% of rdg + 2 digit)(23°C±5°C 45 to 75% RH)
Input Range
DA
23
24
25
2A
Measuring
Range
±9.999mA
±99.99mA
±999.9mA
4 to 20mA
Display
Adjustable
Offset
±9999
Fullscale
±0~9999
Internal
Resistance
10Ω
1Ω
0.1Ω
10Ω
Input
Protection
±150mA
±500mA
±3A
±150mA
Photo coupler output:
(NPN)
Hysteresis:
External control:
Accuracy: ±(0.1% of rdg +2 digit)(23°C±5°C 45 to 75% RH)
±(0.3% rdg +2 digit) for 25 range
■ General specifications
●Measurement block
Operation method:
Conversion rate:
Temp. coefficient:
Display:
Polarity display:
Overrange warning:
Maximum display:
Decimal poin:
Zero display:
●External control block
Hold:
Start:
Digital zero:
Peak hold
Valley hold:
Peak Valley hold
Pattern selection:
●Comparison block
Control method:
Setting range:
Setting condition:
Single ended
Dual slope
12.5 time/sec (50 Hz), 15 time/sec (60 Hz)
NMR more than 50 dB (50/60 Hz)
±(0.005% of rdg +0.3 digit)/°C
Red LED, 14.2 mm height
Green LED, 8 mm height for setpoint
Automatic "–" display when the computation
result is minus
display 0L or –0L
0 to ±9999 (4 digit)
Settable to any digit position (by front sheet
switch)
●Common block
Memory backup:
Operating temp:
Storage temp:
Power supply:
Power consumption:
Dimensions:
Weight (unit only):
Shorted COM terminal and S/H terminal or level "0"
Shorted COM terminal and S/H terminal or level "1"
Shorted COM terminal and DZ terminal or level "0"
(displayed zero and that value is stored)
Shorted COM terminal and PH terminal or level "0"
Any one of 8 patterns is settable in combination of
COM terminal and P.SEL terminal 0, 1 and 2
Level "0"
: 0 to 1.5V
Level "1"
: 3.5 to 5 V
Input current
: less than -2 mA
Dielectric noise:
Power supply for sensor:
Accessories:
-9999 to 0 to +9999 (Including polarity)
Comparison
result
HH
HI
GO
LO
LL
Contact capacity
250 V AC
0.2 A Resistive load
120 V AC
0.5 A Resistive load
28 V DC
1 A Resistive load
Voltage = Max. 30 V
Current = Max. 50 mA
Saturation voltage = less than 1.2 V
at 50 mA
1 to 999 digit for each set point
Relay reset
Shorted COM terminal and R.RE
terminal or level "0"
Level "0"
: 0 to 1.5 V
Level "1"
: 3.5 to 5 V
Input current
: less than -2 mA
back up 10 years
0 to 50°C 35 to 85% RH (No
condensation)
-10 to 70°C less than 60% RH
90 to 264 V AC (50 Hz/60 Hz)
Approx 10 VA typ (at 100 V AC)
96 mm(W) ✕ 348 mm(H) ✕ 3148 mm(D)
DIN size
Approx 450 g
Input/COM, EXC (0 V), comparative
output, 500 V DC/1 min.
Input/COM of each output
(BCD:FD.COM, ANALOG:-, RS232C:SG, RS-485)
500 V DC/1 min.
Power supply terminal/input terminal,
COM, EXC (0 V), case, comparative
output, 1500 V AC/1 min.
Power supply terminal/COM of each
output (BCD:D.COM, ANALOG:-, RS232C:SG, RS-485) 1500 V AC/1 min.
500 V DC more than 100 MΩ at the
above terminals
Power supply terminal
normal/common mode ±1500 V
24 V DC±10% 40 mA ripple 100 mVp-p
Instruction manual
quick manual, setting list, unit label,
terminal cover
37
SETPOINT COMPARATOR
AM-147
■ Ordering Code
Comparator
●BCD data output (isolated input (Lo))
• At TTL
Measured data:
Tri-stage parallel BCD, Positive logic, latch output
Polarity signal:
Level "1" at minus input
Over signal:
Level "1" at overflow input
Positive pulse approx. 20 ms at every
measurement completion (available negative
logic the above signals)
TTL level, funout 2, CMOS 5V
• At open collector (NPN)
Measured data:
Polarity signal:
Over signal:
Transistor output capacity:
ENABLE:
Negative logic transistor "ON" at logic 1
Transistor "ON" at minus input
Transistor "ON" during a period of approx. 20
ms at every measurement completion
Applied voltage, max. 30V current max. 10
mA saturated output voltage less than 1.2 V
at 10 mA
Shorted ENABLE terminal and D.COM
terminal or level "0", Transistor output are
OFF (TTL output is high impedance status)
Level "0"
: 0 to 1.5 V
Level "1"
: 3.5 to 5 V
Input current
: less than - 2 mA
AM-147-
-
Comparator Output
Output
Power Supply
Input
Range
{
{ 1.2. Relay
Photo Coupler
1. None
2. BCD(Open collector)
3. BCD(TTL)
4. RS-485
5. RS-232C
6. ANALOG(4 to 20mA)
7. ANALOG(0 to 10V)
1. 90 to 264VAC
{
DV(11,12,13,14,15,1V)
DA(23,24,25,2A)
■ Dimensions
HH HI
Front
GO
LO LL
HH HI SET
48
■ Output specifications
LO LLSET
E
M
ME PH HH. LL
S
P.NO DZ RE
96
No. of connectable meter:
Line length:
+
–
7
Side
MADE IN JAPAN
127
✻33
92 +0.8
–0
Input/output
Input/output
45+0.6
–0
Non-reversible output
Reversible output
148
144
Min70
●RS-485 (Isolated input (Lo))
Conforming to EIA RS-485
Electrical characteristics:
2-wires system half-duplex (Polling and selecting)
Transmission speed:
2400/4800/9600/19200 bps
Start bit:
1 bit
Data length:
7 bits
Error detection:
Even parity (BCC)
Stop bit:
2 bits
Character code:
ASCII code
No protocol
Signal name used:
Signal name
Signal
Signal direction
Panel Cutout
Up to 31 meters
Up to 500 m in total
Min120
●RS-232C (Isolated input (Lo))
Electrical characteristics:
Conforming to EIA RS-232C
Full duplex
Synchronous method:
Start and stop
Transmission speed:
2400/4600/9600/19200 bps
Start bit:
1 bit
Data length:
7 bits
Error detection:
Even parity
Stop bit:
2 bits
Character code:
ASCII code
(A.OUT)
Relay Output
0-10V
4-20mA HH C HI
GO LO C LL
Upper
1
2
+
–
3
4
RS-485
●Analog output (Isolated input (Lo))
Resolution:
13 bits
Output response:
Less than 0.5S (0 to 90%)
Output
0 to 10 V
4 to 20 mA
Resistive load
More than 10 kΩ
0 to 550Ω
Accuracy (23°C ± 5°C)
±0.5% FS
±0.5% FS
5
6
7
8
9
10
(C) (e) (C) (e) (C) (C) (e) (C)
Photo Coupler
ON
OFF
TERMINATER
EXC
P.SEL
Ripple
50 mV P-P
Less than 0.5%
0
1
2
P.H
9
10
11
12
Lower
1
2
D.Z R.RE S/H
13
3
4
* Ripple for 4 to 20 mA at resistive load 250Ω, 20 mA
14
5
HI
15
17
16
6
LO COM
0V +24V
7
8
E
AC POWER
C
B
A
BCD OUT
101
102
100
2
8 2
103
8 2
ENABLE
OVER D.COM
8 NC NC
NC NC NC D.COM
1
34
2
33
1
4 1
101
4
102
1
4
RS232C output
38
13
25
NC NC NC D.COM
NC NC POL
PC D.COM
103
SG
100
4 1
CTS
RTS
RXD
TXD
BCD output
8 2
1
14
SETPOINT COMPARATOR
AM-749
■ Features
✽ Four Setpoints
• Conversion Rate 12.5 times / sec (50Hz),
15 times / sec (60Hz).
• Peak, Valley, Peak-Valley Hold, Digital zero.
• Eight Pattern Setting (EEPROGRAM Back Up).
• Including Power Supply For Sensor 12V 80mA.
Comparator
• Power Supply (AC90~264V).
• Direct Setting Function.
Input Range
DV
11
12
13
14
15
IV
Measuring
Range
±199.99mV
±1.9999V
±19.999V
±199.99V
±700.0V
1~5V
Display
Adjustable
Offset
±19999
Fullscale
±0 to 19999
Input
Impedance
100MΩ
100MΩ
1MΩ
10MΩ
10MΩ
1MΩ
Max allowable
input voltage
±250V
±250V
±250V
±500V
±700V
±250V
High high limit set-value Measured value
High limit set-value Measured value
High / high limit set-value Low / low limit set-value
Measured value High limit set-value
Low limit set-value
Measured value Low / lowlimit set-value
Measured value Low limit set-value
Comparison relay:
Accuracy: ± 0.03% rdg ±2 digit (23°C±5°C)
Photo-coupler output:
Input Range
DA
23
24
25
2A
Measuring
Range
±19.999mA
±199.99mA
±1.9999A
4~20mA
Display
Adjustable
Offset
±19999
Fullscale
±0 to 19999
Input
Impedance
10Ω
1Ω
0.1Ω
10Ω
Max allowable
input voltage
±150mA
±500mA
±3A
±150mA
Hysteresis:
External Control:
Contact capacity
Accuracy: ± 0.1% rdg ±2 digit (23°C±5°C)
± 0.3% rdg ±2 digit only for 25 range
• Measurement block
Measurement function: Specify one measuring range from DC voltage
and DC current measuring ranges.
Input circuit:
Single-ended
Operation method:
Dual slope
Input bias current:
100pA (TYP)
Conversion rate:
12.5 times / sec (at 60Hz)
15 times / sec (at 50 / 60Hz)
NMR-More than 50 dB (at 50 / 60Hz)
Display:
7-segment LED (Light emitting diode numeric
element)
Height, 10mm (red)
Monitor / sub-display units-Height 8mm (green)
Polarity display:
"-" is displayed when the computed result is
negative.
Overrange warning:
"OL" LED (red) flashes when input signal exeeds
measuring or display range.
Mximum display:
±99999 (5 digits)
Decimal point:
Settable at any position
(BY pressing sheets switch)
Zero display:
Reading "zero" suppression
• External control
Hold:
Shorting between COM and S/H terminals or "0" level
Start:
Open between COM and S/H terminals or "1" level
Value just before COM and DZ terminals are shorted
Digital zero:
or input level is set at "0" is displayed as "zero" and
that value is stored.
Peak hold:
Respective function is activated when COM and
Valley hold
PH terminals are shorted or input level is set at "0".
Peak valley hold:
Any one of 8 patterns is settable in combination of
Pattern selection:
COM terminal with any one of P SEL terminals 0, 1,
and 2.
"0" level : less than 1.5V
"1" level : 3V to 30V
Input current :less than -5mA
• Comparioson block
Control method:
Computaion by microcomputer
Measurinng range:
High / Low limit setting including polarity, –99999 to
Comparison:
0 to +99999
Setting condiotion:
By sampling period
No setting restrictions for set-value
Comparison result
AM-749
HH
HI
GO
LO
LL
250 AC 0.2A Resistive load
120V AC 0.5A Resistive load
28V DC 1A Resistive load
Sink current, 20mA max. (Less than
30V)
Output saturation voltage, Less than
1.2V at 20mA
Settable from 1 to 9999 digits for
each comparison set value
Reset
Comparison operation is suspended
when COM andr1R.RES terminals are
shorted or input level is set at “0”.
“0” level : Less than 1.5V
“1” level : 3 to 30V
Input current : Less than -5mA
■ Common specifications
Memory backup:
Operating temperature
and humidity ranges:
Power supply:
Power consumption:
Dimensions:
Weight:
Noise rejection:
Sensor power supply:
Accessory:
Set data is stored for approx. 10
years by using EEPROM.
0 to 50˚C
35 to 85% RH
90 to 264V AC (50Hz / 60Hz)
Appox. 5VA (st 100 AC)
48mm (H) x96mm (W) x161mm (D),
DIN size
Approx. 600g
500V DC between input / earth E
and case 500V DC between input
terminal / common, digital common,
sensor power supply and relay
output 1500V AC between power
supply terminal / common, digital
common, sensor power supply,
case and relay output.
More than 100MΩ at 500V DC
between each terminal described
above
Power terminals, normal / common
mode, ±1500V square waveform for
1ns at rise, noise, width, 500ns (BY
noise simulator)
12V± 10% 80mA
Ripple, Less than 200mVp-p
Instruction manual
39
■ Optional specifications
■ Ordering Code
•BCD output [Isolated from input(LO)]
Measured date:
Negative logic
NPN open-collector output
Polarity signal:
OVER signal:
Transistor "ON" at "OVER" input
Printing command signal: Transistor "ON" for approx. 10ms at the end of
measurement
ENABLE:
All date output transistors are turned "OFF"
when ENABLE and digital common terminals
are shorted or input level is set at "0".
"0" level:Less than 1.5V
"1" level":3 to 30V
Input current:Less than -5mA
Transistor output capacity: Applied voltage, 30V max. Current, 10mA max.
Output saturation voltage:Less than 1.2V at
10mA
*TTL output is also available.
•RS-232C [Isolated from input(LO)]
Electrical characteristics: Conforming to EIA RS-232C
Communication method: Full duplex
Synchronous method:
Start and stop
Transmission speed:
2400/4800/9600/19200 bps
Start bit:
1 bit
Data length:
7 bits
Error detection:
Even parity
Stop bit:
2 bits
Character code:
ASC II
No protocol
•RS-485 [Isolated from input(LO)]
Electrical characteristics: Conforming to EIA RS-485
Synchronous method:
Start and stop
Communication method: 2-wire system half-duplex
(Polling and selecting)
Transmission speed:
2400/4800/9600/19200 bps
Start bit:
1 bit
Date length:
7 bits
Error detection:
Even parity
BCC(Block check character)check sum
Stop bit:
2 bits
Character code:
ASC II
No protocol
Signal name used:
AM-749 -
Signal
Signal direction
Reversible output
+
–
Input/output
Input/output
No. of connectable meters: Up to 31 meters
Line length:
Up to 500m in total
Comparator Output
Data Output
(11,12,13,14,15,1V)
{ DV
DA (23,24,25,2A)
Range
■ Dimensions
96
TZ
PH
DZ
RE
OL
48
Front
HH
HI
GO
LO
LL
R
P
CONT
S
M
153
7
131
Side
161
170
＋0.6
92 ＋0.8
−0
Min.70
Panel Cutout
Min.120
Upper
HH
HI
c
a
1
e
Output
Resistive load
Accuracy (23˚C ±5˚C)
Ripple
1 to 5V
4 to 20mA
More than 10kΩ
0 to 600Ω
±0.5% F.S
±0.5% F.S
50mVp-p
–
GO
c
a
2
3
c
e
4
5
6
7
8
9
10
c
e
c
e
c
e
c
2
HI
B
c
13
4
A
14
5
15
16
7
6
LO COM E
(Photo coupler output)
EXC
0 12V
DZ R.RES S/H
12
3
C
Digital filter function
100 -digit is fixed to "0" for display
Blanking of LEDs on main, monitor/sub-display
units.
(Only for RS-232C and RS-485 meters)
Zero-point shift is digitally, automatically
corrected. Activated when digital zero function
becomes valid.
PH
a
a(Relay outpuy)
c
11
1
LL
a
10
9
Lower
LO
c
P.SEL
１２
０
Tracking zero:
1. None
2. BCD (Open collector)
3. RS-485
4. RS-232C
5. ANALOG
Power Supply 1.AC90V~264V
•Analog output [Isolated from input(LO)]
Any display range to output analog signal can be set.
Resolution:
16 bits
Output response:
Less 0.5s
Moving average:
Fixed zero:
Display blanking:
{
{1.2. Relay
Photo
44.5
Signal name
-
45 −0
Comparator
SETPOINT COMPARATOR
AM-749
17
8
AC POWER
BCD output
100
2
101
8
2
102
8
2
103
8
2
104
8
2
ENABLE
8 OVER
DG NC NC NC DG
2
34
1
33
1
4
1
0
10
4
1
10
1
4
1
2
4
10
4 POL PC DG NC NC NC DG
4
10
SG
RS-232C
1
3
10
CTS RXD
RTS TXD
1
13
25
14
RS485
OFF
ON
① ② ③ ④ ⑤ ＋
−
NC
NC
SG
TERMINATER
D-SUB Connector
ANALOG output
① ② ③ ④ ⑤
＋
−
＋
−
1V∼5V 4mA∼20mA
40
NC
SETPOINT COMPARATOR
AMH-752
■ Features
✽4000 Time/sec
• Conversion Rate 1000/sec~4000/sec
• 2 input computation(A, B)
• 4-sets/4-pattern Setting
• Peak, Valley, Peak-Valley hold(Option)
• Digital zero(Option)
Comparator
• RS-232C Communication(Option)
• BCD, ANALOG Output(Option)
• Bright LED 10mm(Red)
Model
Range
AMH-752-11
AMH-752-12
AMH-752-13
AMH-752-14
±199.9mV
±1.999V
±19.99V
±199.9V
Display
Adjustable
OFFSET
±1999
FULLSCALE
±1999
Input
Impedance
Input
Protection
100MΩ
±250V
10MΩ
Range
Display
Adjustable
AMH-752-21
AMH-752-22
AMH-752-23
AMH-752-24
AMH-752-25
±199.9µA
±1.999mA
±19.99mA
±199.9mA
±1.999A
OFFSET
±1999
FULLSCALE
±1999
Accuracy: ±0.2% rdg. ±2 digit(23°C±5°C)(a1)
±0.3% rdg. ±2 digit only for AMH-75X-25
±0.2% rdg. ±4 digit(23°C±5°C)(a1)
±0.3% rdg. ±4 digit only for AMH-75X-25
Internal
Resistance
1kΩ
100Ω
10Ω
1Ω
0.1Ω
Input
Protection
±10mA
±50mA
±150mA
±500mA
±3A
Range
AMH-752-1V
1-5V
Display
Adjustable
Input
Impedance
Input
Protection
1MΩ
±250V
Accuracy: ±0.1% rdg. ±3digit (23°C±5°C) (a1) (Normal Speed Mode)
±0.1% rdg. ±5digit (23°C±5°C) (a1) (High Speed Mode)
■ 4-20mA Measurement
AMH-752-2A
4-20mA
Display
Adjustable
Input
Resistance
Input
Protection
10Ω
±150mA
OFFSET ±1999
FULLSCALE ±1999
Accuracy: ±0.1% ±3 digit (23°C±5°C) (a1) (Normal Speed Mode)
±0.1% ±5 digit (23°C±5°C) (a1) (High Speed Mode)
*a=Scaling Coefficient
■ Specifications
1.Measuring function:
2.Operation method:
3.No. of input points:
*4.Input selection:
5.Input circuit:
6.Input bias current:
*7.Conversion Rate:
8.Display:
9.Display speed:
Mode
No.
Conversion Rate
(1ch) per sec.
Conversion Rate
(2ch) per sec.
250
Mode
No.
Conversion Rate
(1ch) per sec.
Conversion Rate
(2ch) per sec.
11
25
(200)
12
12.5
(400)
12.5
6.25
Specify one type from among DC voltage, DC
current and instrumentation input signal
measurements.
Successive approximation type
2(A ch. and B ch.)ch./channel
A, B, A+B, A-B, A & B, and {(A-B)/ |B| }100
Single-ended type
1nA(TYP)
1.25 times/sec to 4000 times/sec(For 1 ch.)
0.652 times/sec to 2000 times/sec(For 2 ch.)
LED
Measured-value display unit character
height;10.0mm(red)
Monitor character height ; 8mm(green)
12.5 times/sec(Only in the normal speed mode)
Display in the high-speed mode ; Displayed only
during hold.
1
4000
(1)
High Speed Mode
2
3
2000
1333.3
(2)
(3)
4
1000
(4)
2000
1000
500
666.7
Normal Speed Mode
7
8
9
250
125
100
(20)
(40)
(50)
125
62.5
50
10
50
(100)
25
Normal Speed Mode
13
14
15
10
5
2.5
(500) (1000) (2000)
5
2.5
1.25
16
1.25
(4000)
0.625
( )Average time
10.Polarity display:
11.Overrange warning:
12.Zero display:
13.Decimal point:
OFFSET ±1999
Range
500
High Speed Mode
FULLSCALE ±1999
Model
6
500
(10)
Normal Speed Mode
■ 1-5V Measuement
Model
5
1000
(5)
±500V
Accuracy: ±0.1% ±2 digit(23°C±5°C)(a1)(Normal Speed Mode)
±0.1% ±4 digit(23°C±5°C)(a1)(High Speed Mode)
Model
Mode
No.
Conversion Rate
(1ch) per sec.
Conversion Rate
(2ch) per sec.
14.Maximum display:
15.External control:
Automatic "_" display when the
computation result is minus
Overflow display when input signal
exceeds measuring range
LED(red)flashes.(Display:Value just
before overflow occurs)
Leading "zero" suppression
Settabel to any position(by dip switch at
the front).
±1999
Start/hold(start hold A type)
Start/Start terminal open(or 5 V)
Hold/Shorting between digital common
and hold terminals(or 0 V)
*:Sample hold(start hold B type)
Only one measurement is performed from
rise of positive or negative pulse of more
than 500µ s and the result is out-put.
*:Digital zero
Function of making the mechanical initial
value such as of pressure sensor,
potentiometer, etc.
to zero electrically. By shorting between
the digital common and digital zero
(for A ch. or B ch.)
terminals, or at 0V;The displayed value
just after the above shorting made or
voltage is set to 0 V is changed to "zero"
and the value at that
time is stored.
(A ch. and B ch. can be independently
controlled.)
*:Peak hold, valley hold and peak valley
hold
•Peak hold Display of maximum value
measured
•Valley hold;Display of minimum value
measured
•Peak valley hold;
Display of the difference between
maximum and minimum value measured
The respective display function works
with the common and above terminals
shorted or at 0 V.
(However, only display is made, and
comparison output is always in
accordance with voltage or current value
applied between input Hi and Lo.)
*:Settable on the sheet key at the front.
41
SETPOINT COMPARATOR
AMH-752
■ Comparison Section
1.Control method:
2.Setting range:
■ Optional Specifications
High/low limit setting including polarity(2/4step setting)-1999 to 0 to +1999
Tri-state, Parallel BCD output, Fan out 2
Polarity output/At minus value;"1"
Overflow output/At overflow;"1"
P.C output;At the end of A/D conversion,
plus pulse in approx. 500µs width
*Only in the normal speed mode
Bidirectional(Full duplex)
1.BCD output:
(TTL level)
3.Comparison conditions (display):
Comparator
Measured value>High/high limit set-value
High/high limit set-value≧Measured-value
>High limit set-value
High limit set-value≧Measured-value
≧Low limit set-value
Low limit set-value<Measured-value
≧Low/low limit set-value
Low/low limit set-value>Measured-value
4.Comparison display:
Comparison result
AMH-752
HH (HI)
HI
GO
LO
(LO) LL
As a comparison result, the respective light
emitting diode lights.
Output voltage;±0 to 2.5V
Resolution;0.25mV/digit
Accuracy;0.5% FS(23˚C±5˚C)
External resistance;More than 20kΩ
Overvoltage;Approx.±3.5V, less than 5V
*Any of high speed and normal speed
modes is available.
4.Absolute value display comparison:
Function of outputting absolute value
regardless input single polarity
■ Ordering Code
AMH-752 -
-
-
Set data can be reserved for about 10 years
using EEPROM.
2.Operating temperature and humidity:
0 to 50˚C, 35 to 85% RH
3.Power supply:
90 to 132V AC 50/l60Hz
180 to 264V AC 50/60Hz
(Internal jumper wire selection)
4.Power consumption:
Approx. 5VA(at 100V)
5.Dimensins:
48mm(H) 96mm(W) 158mm(D), DIN size
6.Dielectric strength:
Between input and grounding(E)terminals,
500V DC
Between input and digital common/relay
output/transistors output;500V DC,each
terminal/grounding(E)/digital common/relay
output/transistor outpu;1 min at 1500V AC,
each.
7.Insulation resistance: Between each terminal described above, more
than 100MΩ at 500V DC
1.Memory backup:
8.Weight:
9.Accessories:
10.Others:
42
Approx. 600g(mainframe)
Input/output screw terminals, 2 pcs.
Instruction manual
Data output plug(Amphenol 57-30360)
For unit display, contact us.
Output
{
Power
Supply
{ 1.2. AC90~132V
AC180~264V
Range
{
1. None
2. BCD
3. ANALOG
4. BCD,ANALOG
R. RS-232C
11 21 1V
~
■ Common Specifications
{
Compares 1. Relay Output
Output
(0.625Hz~80Hz)
2. Photo Coupler
Output
(0.625Hz~4kHz)
~
5.Comparison relay output:
HH, HI, GO, LO, and LL(1 "a", each)
6.Relay output cycle:
Approx. 12.5ms
Conversion Rate: When the speed is slower
than 80 times /sec, output for
each sampling.
At 1ch. input
Conversion Rate: When the speed is faster
than 80 times/sec, outputs
the result at that time at
about 12.5 msec
intervals.(Excluded at
start/hold.)
7.Relay contact capacity: 250V AC, 0.1A Resistive load
120V AC, 0.5A Resistive load
28V DC, 1A Resistive load
8.Photo-Coupler output: Sink current;20mA max.(less than 30 V)
(NPN open-collector)
9.Photo-Coupler output cycle:
Approx. 250µs at the sampling speed of 4000
times/sec for 1ch. input
For others;Depending on each sampling
speed
10.Hysteresis:
Settable from 1 to 999 digits for each
comparison set-value.
11.External control:
Comparison output reset with the reset and
digital common terminals shotred(or at 0 V)
2.RS-232C:
(Conformance)
3.Analog output:
14 25 2A
SETPOINT COMPARATOR
AMH-752
■ Dimensions
■ Data Output
96
48
TZ
PH
DZ
RE
Front
M
P
Comparator
BCD OUTPUT
A.OUT COM
RS-232C P.SEL
D. COM
OVER
103
101
PC
RTS CTS SG 1 D.COM
1 2 4 8 1 2 4 8 POL
19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36
OVE
HS
HH
HI
GO
LO
LL
S
※
158
1
2
3
4
5
6
1
2 4
100
8
1
2 4
102
7
7
BCD OUTPUT
8
9 10 11 12 13 14 15 16 17 18
8 P.H
RXD TXD SG 0 D.COM
D.Z.(A) D.Z.(B)
ENABLE A.OUT RS-232C P.SEL
Control
Control
ANALOG
Side
92 ＋0.8
−0
Min.70
45 −0
＋0.6
SG
Panel Cutout
13
25
CTS RXD
RTS TXD
1
14
D-SUB Connector
Min.120
Relay Output
HH
c
HI
a
c
GO
a
c
LO
a
c
LL
a
c
a
① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩
(UPPER)
c=Common
a= a Contact
Relay Coupler Output
HH
Upper
e
HI
c
e
GO
c
e
LO
c
e
LL
c
e
c
① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩
(UPPER)
e= Emitter
c= Collector
5.9max
φ3.2min
５min
INPUT
Control
E
3.6max
POWER
Ach A.G Bch A.G COM S/H RESET
Lower
① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩
(LOWER)
43
SETPOINT COMPARATOR
AMH-762
✽High Conversion rate
1000times/sec (Normal speed mode)
4000times/sec (High speed mode)
■ Features
• High Conversion Rate, 1000times/sec (Normal speed mode)
4000times/sec (High speed mode)
• 2 inputs computation (A input, B input)
• Digital Zero, Peak Hold, Valley Hold, Peak-Valley Hold
Comparator
• Available 8-pattern Setting for Scaling value and setpoints
(Data Back-up EEPROM)
•Excitation Supply 24VDC 40mA
•RS-232C, RS-485 Output (Option)
•BCD, Analog Output (Option)
•Power Supply (90 to 264VAC)
Model
Range
•Bright LED, 10mm (Red)
Display Adjustment
Input Impedance Input Protectio
AMH-762-13 ±9.999V Offset ±10000
Fullscale ±0 to 10000
±250V
1MΩ
Display:
Display Speed:
Accuracy:±0.1% FS (23°C±5°C)
■ 1 to 5V Measurement
Model
Range
AMH-762-1V 1 to 5V
Polarity :
Display Adjustment
Input Impedance Input Protectio
Offset ±10000
±250V
1MΩ
Max. Display:
Decimal Point:
Zero Display:
EXternal Control:
■ 4 to 20mA Measurement
Model
Range
Display Adjustment
Internal Resistance Input Protectio
AMH-762-2A 4 to 20mA Offset ±10000
±70mA
50Ω
※Condition for accuracy, (FSC-OFS)/(FIN-OIN) is less than 1
■ Specifications
• Measuring Section
Operation Method:
No. of Input:
Conversion Rate :
Mode
No.
Conversion Rate
(1ch) per sec.
Conversion Rate
(2ch) per sec.
44
Level "0"= 0 to +1.5V
Level "1"= +3.5 to 5V
Current= less than -5mA
✽Not provided PH, DZA and DZB for
RS-232C and RS-485 output
High Speed Mode
Mode
No.
4
Conversion Rate
1000
(1ch) per sec.
Conversion Rate
500
(2ch) per sec.
Mode
No.
Conversion Rate
(1ch) per sec.
Conversion Rate
(2ch) per sec.
Single Ended
Successive approximation type
A input and B input
0.5times to 4000times(only use one input)
0.25times to 2000times(use two input)
1
2
4000
2000
2000
1000
Nomal Speed Mode
10
20
40
80
100
500
400
200
100
50
40
250
200
100
50
25
20
200
400
Nomal Speed Mode
800
1000
2000
4000
8000
20
10
5
4
2
1
0.5
10
5
2.5
2
1
0.5
0.25
8
LED,10mm hight (Red)
8mm hight (Green) for monitor
1.25, 2.5, 12.5, 25times/sec for
Normal speed mode
When pressed key of "C", appear
display value for High speed mode
When input exceeds the maximum
display, display OL and flash
±99999
Hold ; Shorted D.COM and S/HA,
S/HB
Start; Open D.COM and S/HA, S/HB
terminal or "1" level
Digital Zero; Shorted D.COM and
DZA, DZB terminal or level "0"
Peak Hold;
Valley Hold; Shorted D.COM and PH
Peak Valley Hold;(Compare the
display value)
Selected either one
Pattern Select; Combination of
D.COM and P.SEL terminal
SETPOINT COMPARATOR
AMH-762
• Comparator Section
Control System:
Setting Range:
• Common Section
Memory Back-up :
Operating Temp:
Power Supply:
Power Consumption:
Dimensions:
Weight:
Excitation Supply:
Accessories:
EEPROM (Rewrite more than 100,000 times)
back up 10 years
0 to 50°C 35 to 85% RH
90 to 264VAC
Approx 10VA TYP. (at 100V)
48(H) 96(W) 161(D) mm DIN size
Approx. 600g (unit only)
Input/earth, COM, Comparative output,
DC500V/ 1 min.
Input/D.COM of each output terminal,
DC500V/1 min.
Power supply/D.COM, case, comparative
output, 1500VAC/1 min.
500VDC more than 100M ohms at the above
terminals
24VDC ±10% 40mA (Ripple less than 100mV
p-p)
Instruction manual
● RS-232C (Isolated input (Lo))
Electrical Characterstics: Conforming to EIA RS-485
Communication Method: Full duplex
Synchronous Method:
Start and Stop
Transmission Speed:
2400/4600/9600/19200 bps
Start Bit:
1 bit
Data Length :
7 bits
Error Detection:
Even parity
Stop Bit:
2 bits
Character Code:
ASCII code
Transmission Control:
No protocol
Comparator
Microcomputer
-99999 to +99999 with polarity
High High setpoint < Indication
/HH
/HI
High setpoint < Indication
High setpointIndicationLow setpoint
/GO
High high setpointIndicationLow low
setpoint
Low setpoint > Indication
/LO
Low low setpoint > Indication
/LL
Relay Contact Capacity: 250VAC 0.2A Resistive load
120VAC 0.5A Resistive load
28VDC 1A Resistive load
Photo Coupler Outpu:
Voltage=Max. 30V
Current=Max. 20mA
Saturation voltage=less than 1.2V at 20mA
Hysteresis:
1 to 9999 digit each setpoints
External Control:
Reset; Shorted D.COM and R.RE terminal or
level "0"
● Analog Output (Isolated input (Lo))
Output
Resistive load
Accuracy(23°C±5°C)
1 to 5V
More than 10KΩ
±0.5% FS
4 to 20mA
0 to 500Ω
±0.5% FS
■ Other Functions
Moving Average:
Fixed Zero:
Display Blanking:
Tracking Zero:
Digital Filter function
10˚digit is fixed to "0" for display
Blanking of LEDs on main and
monitor display
Zero point shift is digitally,
automatically corrected.
Activated when digital zero function
becomes valid
■ Output
● BCD data output (Isolated input (Lo))
•At Open collector (NPN)
Negative logic transistor "ON" at logic 1
Measured Data:
Polarity Signal:
Over Signal:
Printing Command Signal:
Transistor "ON" during a period at every
Transistor Output Capacity:
Applied voltage, 30V max. current 10mA max.
Saturated output voltage less than 1.2V at
10mA
*Available TTL output
● RS-485 (Isolated input (Lo))
Electrical Characterstics: Conforming to EIA RS-485
Synchronous Method:
Start and stop
Communication Method: 2-wires system half-duplex (Polling and
selecting)
Transmission Speed:
2400/4800/9600/19200 bPS
Start Bit:
1 bit
Data Length:
7 bits
Error Detection:
Even parity (BCC)
Stop Bit:
2 bits
Character Code:
ASCII code
Transmission Control:
No protocol
Signal name used:
Signal name
Signal
Signal Direction
+
Input/output
Reversible output
–
Input/output
No. of Connectable Meter:
Line Length:
Up to 31 meters
Up to 500m in total
45
SETPOINT COMPARATOR
AMH-762
■ Ordering Code
AMH-762- VA -
-
Upper
1. Relay
Comparator Output
2. Photo Coupler
1. None
BCD Output 2. TTL
3. Open Collector
1. None
2. BCD
Output 3. RS-485
4. RS-232C
5. Analog Output (1 to 5V 4 to 20mA)
{
HH
{
Comparator
{
c (e)
GO
LO
LL
① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩
( )：PHOTO COUPLER
Lower
P.SEL
Power Supply 1. 90 to 264VAC
0
Range
HI
a (c) c (e) a (c) c (e) a (c) c (e) a (c) c (e) a (c)
EXC
1
D.COM S/HA S/HB R.RE 0V ＋24V
2
⑨ ⑩ ⑪ ⑫ ⑬ ⑭ ⑮ ⑯ ⑰
■ Dimensions
① ② ③ ④ ⑤ ⑥ ⑦ ⑧
HI
96
A.B ch LO
A.A ch
V.B ch
V.A ch
E
AC POWER
90V∼264V
INPUT
48
Front
TZ
PH
DZ
RE
OL
HH HS
HI
GO
LO
LL
CONT
P
R
M
S
Connector
PH
NC NC NC NC NC NC NC NC NC NC NC NC CLR
153
7
131
DZA NC D.COM
2
34
1
33
NC NC NC NC NC NC NC NC NC NC NC NC NC NC DZB NC D.COM
44.5
Side
Output Connector
100
161
2
170
101
8
2
102
8
2
103
8
2
104
8
2
ENABLE 1
8 OVER
PH
CLR
DZA NC COM
2
34
1
92 ＋0.8
−0
33
1
4
1
Min.70
45 −0
＋0.6
100
Panel Cutout
4
101
1
4
102
1
4
103
1
4 POL
PC NC DZB NC COM
ENABLE 2
104
Analog output
4ー20mA
1ー5V
＋ NC ー NC NC NC NC NC NC ＋ NC ー CLR PH DZH NC COM
Min.120
2
34
1
Panel thickness:0.8 to 5.0mm
33
＋ NC ー
NC NC NC NC NC NC ＋
NC ー
NC NC DZB NC COM
1ー5V
4ー20mA
RS232Coutput
SG
CTS RXD
RTS TXD
1
13
25
14
D-SUB
RS485output
OFF
＋
46
−
NC
NC
SG
ON
TERMINATER
AC VOLTMETER & AMMETER
AP-166
■ Features
✽Standard Type
• Average
• AC 999.9mV~700.0V, AC 999.9mA~999.9mA
Measurement
■ AC Voltage Measurement
999.9mV
9.999V
99.99V
700.0V
Frequency
Range
40Hz~10kHz
40Hz~10kHz
40Hz~4kHz
40Hz~1kHz
Input
Protection
100V
100V
300V
700V
Power Supply
Range
Accucracy: ±(0.3% of rdg. + 3 digit) (23°C ± 5°C, 35 ~ 85%RH)
AP-166-22
AP-166-23
AP-166-24
AP-166-25
999.9µA
9.999mA
99.99mA
999.9mA
12 22
15 25
Internal
Resistance
1kΩ
100Ω
10Ω
1Ω
Frequency
Range
40Hz~1kHz
40Hz~1kHz
40Hz~1kHz
40Hz~1kHz
Input
Protection
10mA
50mA
200mA
1A
96
Front
48
Range
{ 1.2. AC90~132V
AC180~264V
■ Dimensions
■ AC Current Measurement
Model
{
AC V & A
AP-166-12
AP-166-13
AP-166-14
AP-166-15
Input
Impedance
10MΩ
10MΩ
10MΩ
10MΩ
~
Range
~
Model
■ Ordering Code
AP-166-
Accucracy: ±(0.5% of rdg. + 3 digit) (23°C ± 5°C, 35 ~ 85%RH)
■ Specifications
95
71
6.5
Single Ended input Impedance 10MΩ 100PF
or less
Rectifier Circuit:
Represents effective Value of sine wave by
demodulation of mean Value
Conversion Rate:
2.5/sec
Response Speed:
Approx. 2.5sec(10~90%)
Display:
LED, 14.2mm 4 digit
Decimal Point:
Settable to any digit positions
flash display
External Control:
Hold; HOLD terminal and COM shorted
Power Supply:
AC90~132V
AC180~264V
Power Consumtion:
Approx. 2VA
Dimensions:
48(H) × 96(W) × 95(D)mm DIN Size
Weight:
Approx. 270g
Between input terminal and earth(E),
DC500V/1 min. Between power supply
terminal and input terminal, COM, earth(E)
AC1500V/1 min.
Side
Panel cut
Min.70
45＋0.6
−0
92 ＋0.8
−0
Min.120
Upper
① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨
HI
LO
NC COM HOLD
INPUT
NC
E
AC POWER
47
AC Voltmeter
AP-560
■ Features
• No need power supply
• Low cost
• Thin case, 1/8 DIN
AC V & A
■ Dimensions
Model
Range
Resolution
Input Protection
AP-560-1
AP-560-2
60 to 250 V AC
240 to 600 V AC
1V
1V
300 V
700 V
Front
48
Accuracy : ± 3 digits (23°C ± 5°C 35 to 85%RH)
96
■ Specifications
Conversion Rate:
Display:
Power Consumption:
Operating Temp.:
Dimensions:
Weight:
2.5/sec
none
3 digit, 14.2 mm Red LED
35 mA (MAX)
0 to 50˚C 35 to 85%RH
96(W) 48(H) 22(D)mm DIN size
Approx. 55 g
input terminal/case, 1500 V DC/1 min
input terminal/case, more than 100 M ohm at
500 V DC
6.3
12.2
Side
■ Ordering Code
AP-560-
92 ＋0.8
−0
Min.70
45 −0
＋0.6
1. 60 to 250 V AC
2. 240 to 600 V AC
Panel cutout
Min.120
Panel thickness 0.8 to 3.2 mm
AC
48
INPUT
AC VOLTMETER & AMMETER
A5-
■ Features
• Low Cost
DC9~60 V
■ AC Voltage, Current (Average)
Input Frequency
Display
40 Hz to 1 kHz
offset ±9999
Measurement
Range
99.99 V
600 V
Input Frequency
Display
40 Hz to 1 kHz
offset ±9999
Input Frequency
Display
23
24
25
Measurement
Range
9.999 mA
99.99 mA
999.9 mA
40 Hz to 1 kHz
offset ±9999
Range
Measurement
Range
Input Frequency
26
5A
50 Hz or 60 Hz
11
12
13
04
Range
05
14
15
Range
08
09
Maximum
Resolution
10 µV
100 µV
1 mV
Input Impedance
Input Protection
Accuracy
more than 1 MΩ
100 V
100 V
250 V
±(0.2% of rdg + 10 digit)
Maximum
Resolution
10 mV
100 mV
Input Impedance
Input Protection
Accuracy
more than 1 MΩ
250 V
600 V
Maximum
Resolution
1 µA
10 µA
100 µA
Input Impedance
Input Protection
Accuracy
10 Ω
1Ω
0.1 Ω
100 mA
500 mA
3A
Display
Maximum
Resolution
Input Impedance
Input Protection
Accuracy
offset ±9999
1 mA
CT
8A
Maximum
Resolution
10 µV
100 µV
1 mV
Input Impedance
Input Protection
Accuracy
more than 1 MΩ
100 V
100 V
250 V
Maximum
Resolution
10 mV
100 mV
Input Impedance
Input Protection
Accuracy
more than 1 MΩ
250 V
600 V
Maximum
Resolution
1 µA
10 µA
100 µA
Input Impedance
Input Protection
Accuracy
10 Ω
1Ω
0.1 Ω
100 mA
500 mA
3A
AC V & A
Measurement
Range
99.99 mV
999.9 mV
9.999 V
Range
■ AC Voltage, Current (TRUE-RMS)
Measurement
Range
99.99 mV
999.9 mV
9.999 V
Input Frequency
40 Hz to 1 kHz
offset ±9999
Measurement
Range
99.99 V
600 V
Input Frequency
Display
40 Hz to 1 kHz
offset ±9999
Input Frequency
Display
23
24
25
Measurement
Range
9.999 mA
99.99 mA
999.9 mA
40 Hz to 1 kHz
offset ±9999
Range
Measurement
Range
Input Frequency
Display
Maximum
Resolution
Input Impedance
Input Protection
Accuracy
26
5A
50 Hz or 60 Hz
offset ±9999
1 mA
CT
8A
Range
11
12
13
06
Range
07
14
15
Range
10
11
Input configuration
Response time
Crest factor
Dead zone
Display
: Single ended
: Approx. 1 sec.
: 4:1 at fullscale (only for TRUE-RMS)
: 0 to 99 digit
■ Specifications
Display:
Conversion Rate:
Maximum Display:
Zero Display:
Decimal Point:
External Control:
Power Supply:
Power Consumption:
Dimensions:
Weight:
■ Ordering Code
12.5 times/sec.
9999
display OL or –OL
0 to 50°C 35 to 85% RH
DC 9 to 60 V
(DC main unit)
Approx. 450 g
AC2000 V/1 min.
DC500 V/1 min.
DC500 V/1 min.
DC500 V/1 min.
A5
Input
04. AC voltage AVG (99.99 mV to 9.999 V)
05. AC voltage AVG (99.99 V to 600 V)
06. AC voltage RMS (99.99 mV to 9.999 V)
07. AC voltage RMS (99.99 V to 600 V)
08. AC current AVG (9.999 mA to 999.9 mA)
09. AC current AVG (5 A)
10. AC current RMS (9.999 mA to 999.9 mA)
11. AC current RMS (5 A)
Output
0. None
1. HI & LO setpoint
2. Analog output
3. RS-232C
4. RS-485
Display
board
1. Single
2. Multiple
Main
board
1. AC100 - 240 V (±10%)
2. DC9 - 60 V
49
DIGITAL SCALING METER
AS-101
■ Features
• Low Cost
• CE Approval
Model
Range
Display
Adjustable
Input
Impedance
Input
Protection
■ Ordering code
AS-101Power supply
AS-101-1V
1~5V
Offset ±10
AS-101-2V
0~5V
Fullscale
1MΩ
±100V
AS-101-3V
0~10V
100~1999
Accuracy : ±(0.1% of rdg. + 2 digits) (23°C ±5°C, 35~85%RH)
Range
Process Monitor
Model
Range
Display
Adjustable
Input
Impedance
Input
Protection
Offset ±10
±70mA
Fullscale
51Ω
100~1999
Accuracy : ± (0.1% of rdg. + 2 digits) (23°C ±5°C, 35~85%RH)
AS-101-2A
{
1V: 1~5V
2V: 0~5V
3V: 0~10V
2A: 4~20mA
■ Dimensions
4~20mA
48
Front
96
■ Specifications
71
56
6.5
＋0.6
Side
45 −0
Measurement function :DC voltage & current measurement.Front
Specify one model from among 4 models.
Operation method :
Dual slope
Input configuration :
Single ended
Input Bias Current :
2nA(Typ.)
Conversion rate :
2.5 times/sec
Normal mode rejection :More than 4dB (50/60Hz) (Typ.)
Max.display :
1999
Overrange indication : When input exceeds the maximum display,
1999 or -1999 flashes
Display :
LED, 14.2mm, 3 1/2-digits
Polarity :
Automatic polarity selection
Polarity display :
A “–” is displayed automatically
External control :
Hold;COM terminal and S/H terminal shorted Side
or level “0”
Decimal point :
Operation Temperature/humidity : 0 ~ 50˚C, 35 to 85%RH
Storage temperature/humidity : -10 ~ 70˚C, 60%RH max.
Power supply :
AC 90V~132V 50/60Hz 2.0VA(Max.) (100V)
180V~264V 50/60Hz 2.0VA(Max.) (200V)
DC 24V ±20% 40mA(Max.) Isolated
Dimensions :
96mm(W) x 48mm(H) x 71mm(D) DIN size
Weight :
AC Approx. 175g DC Approx. 100g
Dielectric resistance : AC type; Between power supply and input
terminal(Lo),COM,case, AC2100V/1 min.
DC type; Between power supply(0V) and
input(Lo), DC500V
Insulation resistance : Between power supply terminal(0) and
input(Lo) DC500V more than 100M ohm
Accessory :
Instruction manual, terminal cover,2-axis,2-screw
Standards :
IEC1010-1,EN50082-2,EN50081-2
Setup environment :
Installation category II, Pollution degree 2
Altitude :
2000m max.
Fuse :
Type TR-5 19372-0.2A Slow-blow type
50
{
1: AC 90~132V
2: AC 180~264V
4: DC 24V (Isolated)
Panel cut
92 ＋0.8
−0
INPUT
HI
LO
AC/DC POWER
NC
S/H COM NC
0V
+V
①②③④⑤⑥⑦⑧
PROCESS MONITOR
AS-203A
■ Features
✽Miniature Size
• Easily adjustable offset-fullscale from the front panel
(Span 2000 counts)
• Bright LED, 8mm (Red)
• DIN size 24(H) × 48(W)mm
• Power supply DC5V or DC24V (Isolated)
• 1~5V, 4~20mA Measurement
Input
Protection
±10mA
±50mA
±150mA
±500mA
±3A
Power Supply
Range
Accuracy: 0.1% rdg. ±2 digits (23°C ±5°C)
Range
AS-203A-21
AS-203A-22
AS-203A-23
AS-203A-24
AS-203A-25
±199.9µA
±1.999mA
±19.99mA
±199.9mA
±1.999A
3. DC 5V (Isolated)
4. DC 24V (Isolated)
11 21 1V
14 25 2A
■ Dimensions
Display
Adjustable
Offset ±1000
Fullscale
±100~1999
48
Fullscale
Adjust
24
Model
{
{
Process Monitor
Internal
Resistance
1kΩ
100Ω
10Ω
1Ω
0.1Ω
AS-203A-
~
Fullscale
±100~1999
Input
Protection
±100V
±250V
±250V
±500V
~
Range
±199.9mV
±1.999V
±19.99V
±199.9V
Input
Impedance
100MΩ
100MΩ
10MΩ
10MΩ
~
Model
AS-203A-11
AS-203A-12
AS-203A-13
AS-203A-14
■ Ordering Code
Display
Adjustable
Offset ±1000
Front
Accuracy: ±0.2% rdg. ±2 digits (23°C ±5°C)
±0.3% rdg. ±1 digit only for AS-203A-25
Offset Adjust
■ 1~5V Measurement
Model
Range
AS-203A-1V
1~5V
Display
Adjustable
Offset ±1000
Fullscale 100~1999
Input
Impedance
Input
Protection
1MΩ
±250V
Side
4.8
51
73
■ 4~20mA Measurement
AS-203A-2A
4~20mA
Display
Adjustable
Offset ±1000
Fullscale 100~1999
Internal
Resistance
Input
Protection
51Ω
±70mA
45 ＋0.6
−0
Panel cut
Single Ended
2nA (Typ.)
2.5/sec
40dB (Typ.) (50/60Hz)
Offset Typ. ±0.1, Max. ±0.3 digit/°C
Fullscale Typ. ±0.1, Max. ±0.3 digit/°C
Display:
LED, 8mm 3 1/2 digits
Polarity:
Decimal Point:
1999 flashes
Fullscale Adjustment:
100~1999
Offset Adjustment:
±1000
Span:
2000 counts
Power Supply:
DC5V ±5%, 90mA (Typ.)
DC24V ±20%, 20mA
Power Consumption:
450 mW at 5V, 480 mW at 24V
Dimensions:
24(H) × 48(W) × 73(D)mm DIN Size
Weight:
Approx. 46g
Between power supply (0V) terminal and input
(Lo) terminal, DC500V
Between input (Lo) terminal and mounting
panel, AC1500V/1 min.
Min.65
2
3
HI LO
Start/Hold
■ Specifications
Input Bias Current:
Conversion Rate:
Temperature Coefficient:
Min.35
Range
22.2 ＋0.3
−0
Model
1
INPUT
4
5
6
BL COM
7
8
9
10
OV +5. 24V
Power
51
PROCESS MONITOR
AS-201
■ Features
✽ Fullscale Adjustable
• Adjustable full scale
• Bright LED 10.2mm
• Din size 24(H) ✕ 48(W)
• 1-5V, 0-5V, 0-10V measurement
• Power supply DC5V (NO-ISOLATED)
Model Code
Range
AS-201-1V
AS-201-2V
AS-201-3V
1~5V
0~5V
0~10V
Display
Adjustable
0-100~1999
0-100~1999
0-100~1999
Input
Impedance
1MΩ
1MΩ
1MΩ
Input
Protection
±250V
±250V
±250V
■ Ordering Code
AS-201 -
Range
{
1V
2V
3V
Accuracy: ±0.1% rdg ±2 digit (23°C ±5°C)
■ Dimensions
Decimal Point:
Full-scale Adjustment:
External Hold:
Power Supply:
Power Consumption:
Dimensions:
Weight:
Front
Offset
Adjust
Fullscale
Adjust
48
73
51
4.8
Side
45 +0.6
–0
Min.35
Display:
Polarity:
Single Ended
2nA(Typ.)
2.5/sec
40dB Typ. (50/60Hz)
±0.1 digit (Typ.)/°C
±0.3 digit (Max.)/°C
LED, 10.2mm 3 1/2 digit
1V Range:When input less than 1V, a "-" is
displayed automatically.
2V, 3V Range:When input less than 0V, a "-"
is displayed automatically.
1999 flashes
100~1999
Negative 0V or Short
DC 5V±5% 70mA (Typ.)
0~50°C, 35 to 85%RH
350mW
24(H) ✕ 48(W) ✕ 73(D)mm DIN Size
40g
Between Input(Lo) and Mounted panel,
AC1500V/1 min.
DC500V 100MΩ or more at above terminals
22.2 +0.3
–0
Process Monitor
Input Bias Current:
Conversion Rate:
24
■ Specifications
Panel Cutout
Min.65
Connect input Lo and Ov.
2
HI LO
3
HOLD
1
4
101
INPUT
52
5
6
7
8
9
10
COM 102 103 OV +5V
D.P
Power
PROCESS MONITOR
AL-501A
■ Features
✽ Self Power(4 to 2omA)
• Self power (4~20mA)
• Easily adjustable for offset-fullscale from the front panel
• LCD Display, 12.7 mm
• Screw terminals
• 4~20mA Measurement
Model
Range
AL-501A
4~20mA
■ Dimensions
Display
Adjustable
Offset ±200
Fullscale 100~1999
Input
Protection
96
±50mA
Offset VR
Accuracy: ±0.1% F.S. ±1 digit (23°C ±5°C)
Offset Adjustment:
Voltage Drop:
Display:
Polarity:
Decimal Point:
Power Supply:
Dimensions:
Weight:
Accessory:
48
Fullscale VR
22
12.2
6.3
Side
92 ＋0.8
−0
45 ＋0.6
−0
Front
Single Ended
1999
2.5/sec
NMR 40dB (TYP)
Offset display, ±0.3 digit/°C (Max.)
Fullscale display,±0.3 digit/°C (Max.)
display +1 and blank other digits
100 to 1999
±200 digits
2.2V (at 20mA) Typ.
1.6V (at 4mA) Typ.
LCD, 12.7mm
Current loop power (4 to 20mA)
0 to 50 °C, 35 to 85% RH
48(H) ✕ 96(W) ✕ 22(D)mm DIN size
Approx. 55 g (unit only)
Input (Lo) terminal and earch(E),
500VDC/1min.
Instruction Manual
Process Monitor
Max. Display:
Conversion Rate:
Temperature Coeficient:
Min.70
■ Specifications
Panel Cutout
Min.120
■ Ordering Code
AL-501A
Panel thickness 0.8~3.2mm
Hi
Lo
INPUT
(E)
EARTH
103
102
101
DECIMAL POINT
53
PROCESS MONITOR
AL-213
■ Features
• Self power (4-20mA)
• LED display 10.16mm (red)
• Screw terminal
■ 4-20mA Measurement
Model
AL-213
Display
Offset ± 200
Fullscale 100-1999
Accuracy: ± (0.1% of FS + 1 digit) (23℃ ± 5℃) 35-85%RH
Input Protection
± 50mA
48
Front
24
Range
4-20mA
■ Dimensions
Fullscale adjustment:
Offset adjustment:
Voltage drop:
Display:
Polarity:
Decimal point:
Operating temp.:
Dimensions:
Weight:
Single ended
1999
2.5/sec (TYP)
40 dB (TYP)
Offset display, ±0.3 digit/˚C
Fullscale display, ±0.3 digit/˚C
When input exceeds the maximum display, display 1
and blank other digits
100-1999
±200
5 V at 4 mA
5.3 V at 20 mA
LED (red), 10.16 mm
0 -50˚C 35-85%RH
48 (W) 24 (H) 40 (D) mm DIN size
Between input (LO) and earth (E) DC500 V/min
approx. 55 g
5
7.7
Side
4.3
Process Monitor
Max. display:
Conversion rate:
Normal mode rejection:
10.16
■ Specifications
39.7
Rear
■ Ordering code
AL-213
Panel cutout
45 ＋0.6
−0
＋0.3
22.2 −0
65mm以上
1 2 3
Terminal No. 1
2
3
54
Input HI
Input LO
Earth
35mm
以上
PROCESS MONITOR
AL-512
■ Features
• Self power (4~20mA)
• LED display 14.2 mm (red)
• Screw terminal
■ Dimensions
Model
Range
Display
Input
Protection
AL-512
4~20mA
Offset ±200
Fullscale 100~1999
±50mA
96
■ Specifications
Display:
Polarity:
Decimal Point:
Operating Temp:
Dimensions:
Weight:
Accessory:
Side
22
92 ＋0.8
−0
■ Ordering Code
AL-512
12.2
Min.70
Offset Adjustment:
Voltage Drop:
6.3
45 ＋0.6
−0
Front
Single ended
1999
2.5/sec
NMR 40dB (TYP)
Offset display, ±0.3 digit/°C
Fullscale display, ±0.3 digit/°C
display 1 and blank other digits
100 to 1999
±200
5V at 4 mA
5.3V at 20 mA
LED, 14.2 mm
0 to 50°C, 35 to 85% RH
96(W) × 48(H) × 22(D)mm DIN size
Approx. 55 g (unit only)
Input (Lo) and earth(E), 500VDC/1 min.
Instruction Manual, terminal cover.
Process Monitor
Max. Display:
Conversion Rate:
Temperature Coeficient:
48
Accuracy: ±(0.1% of FS + 1 digit) (23°C ±5°C, 35 to 85% RH)
Panel cut
Min.120
Hi
Lo
INPUT
(E)
EARTH
55
PROCESS MONITOR
AS-243
■ Features
• Easily adjustable offset-fullscale (Span 10000 counts)
• Bright LED, 8 mm (Red)
• DIN size 24 (H) 48 (W) mm
• Power supply DC 24 V (isolated)
• 1-5 V, 0-5 V, 0-10 V, 4-20 mA measurement
■ Dimensions
Model
Range
Display
AS-243-1V
1-5 V
1MΩ
±250V
Offset ±5000
AS-243-2V
0-5V
fullscale
1MΩ
±250V
100 to 9999
AS-243-3V
0-10 V
1MΩ
±250V
Accuracy: ±(0.1%of rdg+2 digit) (23˚C±5˚C 45~75%RH)
48
Front
24
Model
AS-243-2A
Range
4-20mA
Display
Offset ±5000
fullscale
100 to 9999
Internal Resistance Input Protection
50Ω
±50mA
87
5
65
Accuracy: ±(0.1% of rdg+2 digit) (23˚C±5˚C 45~75%RH)
■ General Specifications
Fullscale adjustment :
Offset a djustment :
Span :
Display :
Polarity :
Scaling :
Hold :
Decimal point :
Operating temperature :
Power supply :
Power consumption :
Dimensions :
Weight (unit) :
Dielectric strength :
Insulation resistance :
Accessory :
45 ＋0.6
−0
Min.35
Overrange indication :
Side
Single ended
2 mA (TYP.)
2.5/sec
50dB (TYP.) (50/60 Hz)
Offset display ±0.5 digit/˚C
Fullscale display ±0.01% of span/˚C
display flashes
100 to 9999
±5000
10000 counts
LED, 8 mm (Red)
By switch (rear) and fine volume (front)
COM and S/H terminal shorted
0 to 50˚C 35 to 85%RH
DC24V±20%
30 mA at DC24V
24(H) 48(W) 87(D)mm DIN size
Approx. 50g
Between input (Lo) and mounted panel, AC
1500V/l min.
Between input (Lo) and power supply (0V), DC
500 V/l min.
DC 500 V 100 MΩ or more at the above
terminals
Connector, Instruction manual
22.2 ＋0.3
−0
Thermometer
Input bias current :
Conversion rate :
Normal mode rejection :
Temp. coefficient :
Panel Cutout
Min.65
1
2
3
4
HI
LO
S/H
NC
INPUT
■ Ordering Code
AS-243-
-4
Power Supply 4. DC24V
1V
Range 2V
3V
2A
{
56
5
6
NC COM
7
8
NC
NC
9
10
−
＋
DC POWER
THERMOMETER
A5-
■ Features
• Low Cost
DC9~60 V
• Sensor Type :K, J, T, S, R, B, PT100 Ω
■ Thermocouple
■ Ordering Code
Sensor
Measurement
Maximum
Accuracy
Type
Range
Resolution
–50.0 to 199.9°C
K
KA
0.1°C
±(0.5% of FS)
–50 to 1200°C
K
KB
1°C
±(0.2% of FS)
–50 to 1000°C
J
J
1°C
±(0.2% of FS)
13
–50 to 400°C
T
T
1°C
±(0.6% of FS)
0 to 1700°C
S
S
1°C
±(0.4% of FS)
–10 to 1700°C
R
R
1°C
±(0.4% of FS)
100 to 1800°C
B
B
1°C
±(0.4% of FS) over 500°C
available Fahrenheit display
Cold junction compensator accuracy : ±1°C (10 to 40°C)
Sensor lead resistance
: Less than 50 Ω
Linearizing method
: Digital linearizing
Burn out alarm
: ———
A5
Range
Input
13. Temperature (Thermocouple)
14. Temperature (RTD)
Output
0. None
1. HI & LO setpoint
2. Analog output
3. RS-232C
4. RS-485
Display
board
1. Single
2. Multiple
Main
board
1. AC100 - 240 V (±10%)
2. DC9 - 60 V
Accuracy
±(0.15% of FS)
±(0.3% of FS)
■ Dimensions
92
121
147.5
Sensor
Measurement
Maximum
Type
Range
Resolution
14
PT100 Ω –100.0 to 199.9°C
PA
0.1°C
PT100 Ω –100 to 600°C
PB
1°C
Current for resistance
: Approx. 1 mA
External lead resistance : Less than 10 Ω/lead
Linearizing method
Burn out alarm
: ———
Zero Display:
Decimal Point:
External Control:
Power Supply:
Power Consumption:
Dimensions:
Weight:
45
96
92 +0.8
-0
MIN.70
Conversion Rate:
Maximum Display:
12.5 times/sec.
9999
display OL or –OL
0 to 50°C 35 to 85% RH
DC 9 to 60 V
(DC main unit)
Approx. 450 g
AC2000 V/1 min.
DC500 V/1 min.
DC500 V/1 min.
DC500 V/1 min.
45 +0.6
-0
Display:
7
■ Specifications
48
Range
Thermometer
■ RTD
MIN.120
57
THERMOMETER
AT-205
■ Features
✽Miniature Size
• Small Size
• Power Supply DC5V, DC12V, DC24V
• Sensor Types K, J, and PT-100Ω
• Analog Output (option)
• Screw Terminal
• Bright LED, 8mm (Red)
■ Ordering Code
■ TC Measuring Range
Sensor
K
J
Code
Measuring Range
Resolution
KC
KF
JC
JF
0°C~+1000°C
+32°F~+1832°F
0°C~+400°C
+32°F~+752°F
1°C
1°F
1°C
1°F
Accuracy
(23°C±5°C)
±0.8% F.S.
±0.8% F.S.
±0.8% F.S.
±0.8% F.S.
AT-205-
Output
Thermometer
Code
Code
Measuring Range
Resolution
PT-100Ω
PA
PJ
PF
-100.0°C~+199.9°C
-200°C~+600°C
-328°F~+1112°F
0.1°C
1°C
1°F
Accuracy
(23°C±5°C)
±0.2% F.S.
±0.4% F.S.
±0.4% F.S.
1. None
3. Analog
Power Supply
■ RTD Measuring Range
Sensor
{
{
{
PA
PF
PJ
3. DC5V (Isolated)
4. DC24V (Isolated)
5. DC12V (Isolated)
KC
JC
KF
JF
■ Dimensions
48
Single Ended
2.5/sec
40dB (Typ.)
LED, 8mm 3 1/2 digit
A "-" displayed automatically
DC5V ±5% 90mA
DC12V ±20% 40mA
DC24V ±20% 20mA
Dimensions:
24(H) × 48(W) × 66(D)mm DIN Size
Weight:
Approx. 51g
Between Input (A, B, COM) and 0V terminal,
DC500V
Conversion:
Display:
Polarity:
Power Supply:
24
■ Specifications
Front
℃
66
4.8
51
Side
■ TC Measurement Section
＋0.3
45 ＋0.6
−0
Min.35
22.2 −0
Sensor:
K or J
Temperature Display:
°C or °F
Resolution:
1°C or 1°F
External Lead Resistance: Less than 100Ω
Cold Junction Compensator Accuracy: ±2°C (10°C~40°C)
Burn-out Alarm:
-1999 Flashing
Excessive Input:
DC ±5V
Panel cut
■ RTD Measurement Section
Sensor:
PT-100Ω
Current for Resistance: 1mA (Typ.)
Temperature Display:
°C or °F
Resolution:
0.1°C or 1°C, 1°F
External Lead Resistance: Less than 1Ω/lead
Linearizing Method:
Analog Linearizing
Min.65
① ② ③ ④ ⑤ ⑥ ⑦
■ Analog Output Section
Voltage:
1mV/°C or 1mV/°F, 10mV/°C for PA
Accuracy:
±2% F.S. (23°C ±5°C)
External Lead Resistance: More than 20kΩ
A
B
COM
T.C.
RTD
Pt
58
＋
HOLD
0V
ANALOG DC POWER
OUT
5V/12V/24
STRAIN GAUGE METER
A5-
■ Dimensions
92
■ Strain Gauge
7
121
147.5
Span
Power
Zero
Maximum
Accuracy
Adjustment Resolution
Supply
Adjustment
Range
for
Sensor
Range
17
5V
0.5 µV/digit
–0.3 to +2 mV/V 1 to 3 mV/V
±(0.1% of FS) +2 digit
10 V
1 µV/digit
Sensor
: 350 Ω
Power supply for sensor : 5 V±5% (less than 15 mA)
10 V±5% (less than 30 mA)
■ Specifications
Zero Display:
Decimal Point:
External Control:
Power Supply:
-1
7
Input
Output 0. None
1. HI & LO setpoint
2. Analog output
3. RS-232C
4. RS-485
Display 1. Single
board 2. Multiple
Main
board
MIN.70
■ Output
● HI & LO setpoint output (A5XX1-XX)
Indication > High setpoint
High setpoint Indication Lo setpoint
Indication < Lo setpoint
Setting range
: –9999 to 9999
Hysteresis
: 1 to 999 digit for each setpoints
Relay contact capacity : AC240 V 8 A resistive load
DC30 V 8 A resistive load
HI
GO
LO
● Analog output (A5XX2-XX)
■ Ordering Code
A5
MIN.120
Strain Gauge
Power Consumption:
Dimensions:
Weight:
92 +0.8
-0
45 +0.6
-0
Conversion Rate:
Maximum Display:
12.5 times/sec.
9999
display OL or –OL
0 to 50°C 35 to 85% RH
DC 9 to 60 V
(DC main unit)
Approx. 450 g
AC2000 V/1 min.
DC500 V/1 min.
DC500 V/1 min.
DC500 V/1 min.
48
Display:
45
96
1. AC100 - 240 V (±10%)
2. DC9 - 60 V
Output
Resistive load
0 to 1 V
more than 10 kΩ
0 to 10 V
more than 10 kΩ
1 to 5 V
more than 10 kΩ
4 to 20 mA
less than 550 Ω
Output method : PWM method
Scaling
: Digital scaling
Accuracy
±(0.5% of FS)
● RS-232C (Conforming to EIA RS-232C) (A5XX3-XX)
Communication method
Transmission speed
Start bit
Data length
Parity
Stop bit
Character code
Transmission control process
: Full duplex
: 2400/4800/9600/19200/38400 bps
: 1 bit
: 7 bit/8 bit
: Even parity/odd parity
: 1 bit/2 bit
: ASCII code
: lgnored process
● RS-485 (Conforming to EIA RS-485) (A5XX4-XX)
Communication method
Transmission speed
Start bit
Data length
Parity
Error detection
Stop bit
Character code
Transmission control process
Signal name
: Full duplex
: 2400/4800/9600/19200/38400 bps
: 1 bit
: 7 bit/8 bit
: Even parity/odd parity
: BCC
: 1 bit/2 bit
: ASCII code
: lgnored process
: + non reversal output
– reversal output
Maximum No. of meter connected : 31
Line length
: Up to 500 m in total
59
STRAIN GAUGE METER
ASG-251
■ Features
Load Cell Direct Input
• Hi and Lo Set points
• Bright LED, 8mm (RED)
• Excitation Supply 20mA at DC5V
■ Dimensions
48
Side
87
Hysteresis:
Response Time:
■ Ordering Code
10~+1999 (HI and LO)
By Volume
Setting value ±2 digit (23°C ±5°C) (Typ.)
250VAC 0.1A resistive load
120VAC 0.5A resistive load
28VDC 1A resistive load
HI setpoint%Indication ➔ HI
LO setpoint.Indication ➔ LO
5~12 digit
less than 100msec
21
Panel cut
45 ＋0.6
−0
■ Comparator Section
Setting Range:
Setting Method:
Setting Accuracy:
Relay Contact Capacity:
LO
24
HI
Min.35
Strain Gauge
Front
22.2 ＋0.3
−0
0.1%FS ±1 digit
2.5/sec
NMR 40dB (Typ) (50/60Hz)
Strain gauge sensor (350W)
DC5V±5% 20mA
LED, 8mm (RED)
1999 flashes
Power Supply:
DC19 to 29V (40mA at DC24V)
Operating Temperature: 0 ~ 50°C, 30 ~ 85%RH
Power Consumption:
Approx. 1W
Dimensions:
24(H) × 48(W) × 87(D) mm DIN Size
Weight:
Approx. 53g (unit only)
Between power supply/COM DC500V/ 1 min.
Between -SIG/case AC1500V/ 1 min.
DC500V 100MW at above terminals
Accessory:
Instruction manual, connector
Zero Adjustment:
±0.3mV/V
Gain Adjustment:
1mV/V~3mV/V to fullscale 1999
Zero Drift:
0.02% FS/°C
Gain Drift:
0.02% rdg/°C
Analog Output:
1mV/digit
0.5% FS, less than 250ppm more than
100msec, more than 500W
External Control:
Hold
Accuracy:
Conversion Rate:
Sensor:
Excitation Supply:
Display:
Decimal Point:
22
■ Specifications
Min.65
HI
Lo
POWER
Upper
a
ASG-251
c
1
b
a
c
b
COM
HOLD
0V
+24V
2
3
4
5
6
7
8
9
10
+SIG
−SIG
+EXC
−EXC
COM
NC
NC
NC
COM
ANALOG
OUT
1
2
3
4
5
6
7
8
9
10
INPUT
Lower
60
A7000 SERIES DIGITAL PANEL METER
A7000
■ Features
!
NEW
12 to 48VDC
• Panel cut out 72mm(W) ✕ 36mm(H)
• Option BCD output, RS-232C, RS-485
• HH, HI, GO, LO, LL setpoints
• Input DC, AC, TC, RTD, Frequency, Strain Gauge
Resistance
■Common Specification
Maximum display:
Zero display:
Decimal point:
Operating temp:
Storage temp.:
Power supply:
Power consumption:
Dimensions:
Weight:approx:
Dielectric strength(AC):
(DC):
AC voltage, current (TRUE-RMS)
9999
When input exceed the maximum display
display OVER or –OVER
0 to 50°C(35 to 85% RH)
–10 to 70°C less than 60%RH
100 to 240VAC±10%
12 to 48VDC ±10%
8VA(At AC) 7W(At DC)
72mm(W)X36mm(H)X118mm(D)
160g
AC1500V/min
DC500V/min
Input terminal/output terminal DC500V/min
DC500V more than 100M Ω at the above
terminals
Input Specifications
DC voltage, current
■ A7X11-X
Measurement Range
11
12
13
14
15
±99.99mV
±999.9mV
±9.999V
±99.99V
±700V
Display
Input
Protection
offset
±9999
full scale ±9999
±50V
±50V
±250V
±250V
±700V
Accuracy
(23°C±5°C,35~85%RH)
±(0.1% of rdg+2digit)
21
22
23
24
±99.99µA
±999.9µA
±9.999mA
±99.99mA
Display
Input
Protection
Accuracy
(23°C±5°C,35~85%RH)
offset
±9999
full scale ±9999
±10mA
±50mA
±50mA
±700mA
±(0.1% of rdg +2 digit)
Conversion rate: 100times/sec
■ A7X13-X
Range
Measurement Range
±999.9mA
±2.000A
Display
offset
±9999
full scale ±9999
25
26
11
12
13
14
15
99.99mV
999.9mV
9.999V
99.99V
700.0V
Minimum display
Frequency range:
Response time:
Conversion rate:
Display
Input
Protection
offset
±9999
full scale ±9999
50V
50V
250V
250V
700V
Accuracy
(23°C±5°C,35~85%RH)
±(0.3%of rdg +20 digit)
50 digits
40Hz to 1kHz
Approx 1 sec(10% to 90%)
1000times/sec
■ A7X15-X
Range
Measurement Range
Display
Input
Protection
Accuracy
(23°C±5°C,35~85%RH)
21
22
23
24
99.99µA
999.9µA
9.999mA
99.99mA
offset
±9999
full scale ±9999
10mA
50mA
50mA
500mA
Minimum display
Frequency range:
Response time:
Conversion rate:
50 digits
40Hz to 1kHz
1000times/sec
Range
Measurement Range
Display
Input
Protection
Accuracy
(23°C±5°C,35~85%RH)
25
26
999.9mA
5A
offset
±9999
full scale ±9999
3A
8A
Minimum display
Frequency range:
Response time:
Conversion rate:
■ A7X12-X
Measurement Range
Measurement Range
■ A7X16-X
Range
Range
Input
Protection
Accuracy
(23°C±5°C,35~85%RH)
±3A
A7000
Range
■ A7X14-X
50 digits
40Hz to 1kHz
1000times/sec
Resistance
■ A7X17-X
Range
Measurement Range
Display
Current
Accuracy
(23°C±5°C,35~85%RH)
11
12
13
14
99.99Ω
999.9Ω
9.999kΩ
99.99Ω
offset
±9999
full scale ±9999
5mA
0.5mA
50µA
5µA
Conversion rate:
Measurement method:
100times/sec
Two or Four wire (internal socket changable)
61
A7000
Thermocouple · RTD
Output Specification
■ A7X18-X
■ HH,HI & LO, LLsetpoints output
Range
Sensor type
Measurement
Range
Maximum
Resolution
Accuracy
(23°C±5°C,35~85%RH)
KA
KB
J
T
S
R
B
PA
PB
K
K
J
T
S
R
B
PT100Ω
PT100Ω
–50.0 to 199.9°C
–50 to 1200°C
–50 to 1000°C
–50 to 400°C
0 to 1700°C
–10 to 1700°C
100 to 1800°C
–100.0 to 199.9°C
–100 to 600°C
0.1°C
1°C
1°C
1°C
1°C
1°C
1°C
0.1°C
1°C
± (0.5% of FS)
± (0.2% of FS)
± (0.2% of FS)
± (0.6% of FS)
± (0.4% of FS)
± (0.4% of FS)
± (0.4% of FS)
± (0.15% of FS)
± (0.3% of FS)
Comparative condition :
Indication > High High setpoint
>Indication>High setpoint
High High setpoint=
>Indication=
>Lo setpoint
High setpoint=
>Low Low setpoint
Low setpoint>Indication=
Low Low setpoint>Indication
Setting range:
–9999 to 9999
Hysteresis:
1 to 999 digit for each setpoints
Relay contact capacity: AC125V 0.3A resistive load
DC30V 1A resistive load
Photocoupler capacity: DC30V 50mA
HH
HI
GO
LO
LL
Cold junction compensator accuracy: ±2°C(10 to 40°C)
Sensor lead resistance: less than 50Ω
Linearzing method:
Digital linearizing
Burn out alarm:
----Conversion time:
2.5times/sec
■ BCD output
Type of output:
Logic:
Output rate:
Open collector or TTL
Changeable
DC30V 10mA(open collector)
Funout 2(TTL)
Frequency
■ Analog output (PWM)
■ A7X19-X
Range
Measurement Range
11
12
13
0.1 to 999.9Hz
1 to 9.999kHz
10 to 99.99kHz
Accuracy
(23°C±5°C,35~85%RH)
±(0.2% of FS)
Input type
Input voltage level
Input Protection
Open collector
Logic
Magent
Voltage
L:less than 1.5V(5V, pullup)
L:less than 1V, HI:2.5 to 15V
0.3 to 30V P-P
30V rms to 500V rms
30V
15V
30V
500V
A7000
Prescale:
0.01~10.00
PPR:
1~100
Power supply for sensor: 12VDC±10%
Strain gauge
■ A7X1A-X
Sensor
5V
10V
0 to 1V
0 to 10V
1 to 5V
4 to 20mA
Load resistance
Accuracy
Ripple
more than 10kΩ
±(0.5% of F.S)
50mV p-p
less than 550Ω
Output method:
Scaling:
Resolution:
Response time:
PWM method
Digital scaling
13 bit
approx 0.5sec
■ RS232C (Conforming to EIA RS-232C)
Transmission speed:
Start bit :
Data length:
Parity:
Stop bit:
Character code:
Transmission control process:
Full duplex
4800/9600/19200/38400 bps
1 bit
7 bit/8 bit
Even parity/ odd parity
1 bit/2 bit
ASCII code
Ignord process
■ RS-485 (Conforming to EIA RS-485)
Zero adjustment Span adjustment
range
range
–1 to +1mV/V
Output
1 to 3mV/V
Measurement
range
Accuracy
–4~+4mV/V
±(0.1% of FS)
+2 digit
Sensor:
350 Ω
Power supply for sensor: 5 V±5% (less than 15 mA)
Conversion speed:
1000/sec
Process
Transmission speed:
Start bit:
Data length:
Parity:
Error detection:
Stop bit:
Character code:
Transmssion control process:
Signal name:
Full duplex
4800/9600/19200/38400 bps
1 bit
7 bit/ 8 bit
Even parity/ odd marity
BCC
1 bit/2 bit
ASCII code
Ignord process
+ non reversal output
– reversal output
Maximum no of meter connected: 31
Line length:
up to 500m in total
■ A7X1B-X
Range
Measurement
Range
Display
1V
2V
2A
3A
1 to 5V
±5V
4 to 20mA
±20mA
offset
±9999
Accuracy
±(0.03% of rdg +2digit
±(0.1% of rdg +3digit
Conversion rate:
1000times/sec
Excitation power supply: 12VDC ± 5%
24VDC ± 5% 25mA
62
25mV p-p
A7000
■ Dimensions
■ Ordering Code
–
1.
2.
3.
4.
5.
6.
7.
8.
9.
A.
B.
DC voltage
DC current
DC current
AC Voltage
AC current
AC current
Resistance
Temperature (T/C, RTD)
Frequency
Strain gauge
Process
68
80
87
RE
PH
DZ
ME
P1
P2
P3
HH
HI
GO
LO
LL
E
Power supply
33
118
7.
8.
9.
A.
B.
C.
none
Relay output
Photocoupler output
BCD output (TTL)
BCD output (Open collector)
BCD output (TTL), Photocoupler output
BCD output (Open collector),
Photocoupler output
Analog output
Analog output, Photocoupler output
RS-232C
RS-485
RS-232C, Photocoupler output
RS-485, Photocoupler output
7
Input
0.
1.
2.
3.
4.
5.
6.
36
Output
M
1. AC100 to 240V
2. DC12 to 48V
72
68 +0.7
–0
–0
1
33 +0.6
A7
Min.96
A7000
63
A6000
■ Features
!
NEW
12 to 48VDC
• Panel cut out 96mm(W) ✕ 48mm(H)
• Option BCD output, RS-232C, RS-485
• HI, GO, LO 2 setpoints, Analog output
• Input DC, AC, TC, RTD, Frequency, Strain Gauge
Resistance
(Multiple)
(Single)
■Common Specification
Display:
Conversion rate:
Maximum display:
Zero display:
Decimal point:
Operating temp.:
Storage temp.:
Power supply:
Power consumption:
Dimensions:
Weight:
Dielectric strength(AC):
(DC):
(Common):
AC voltage, current (TRUE-RMS)
Main display Red or Green LED 20 mm
Sub display Red LED 6 mm
1000 times/sec.
9999
When input exceed the maximum display
display OVER or –OVER
0 to 50°C 35 to 85%RH
–10 to 70°C less than 60%%RH
AC 100 to 240 V ±10%
DC 12 to 48 V ±10%
8 VA (max. load)
96 mm(W)X 48 mm(H)X 97.5 mm(D)DIN size
approx. 450 g
AC1500 V/min.
DC500 V/min.
Case/each terminal
AC1500 V/min.
DC500 V more than 100 MΩ at the above
terminals
■ A6XX4-XX
Range
Measurement Range
Display
Input
Protection
11
12
13
14
15
99.99mV
999.9mV
9.999V
99.99V
700.0V
offset
±9999
full scale ±9999
50V
50V
250V
250V
700V
Minimum display
Accuracy
(23°C±5°C,35~85%RH)
50 digits
■ A6XX5-XX
Range
Measurement Range
Display
Input
Protection
Accuracy
(23°C±5°C,35~85%RH)
21
22
23
24
99.99µA
999.9µA
9.999mA
99.99mA
offset
±9999
full scale ±9999
10mA
50mA
50mA
500mA
Minimum display
50 digits
■ A6XX6-XX
Input Specifications
DC voltage, current
A6000
■ A6XX1-XX
Range
Measurement Range
11
12
13
14
15
±99.99mV
±999.9mV
±9.999V
±99.99V
±700V
Measurement Range
21
22
23
24
±99.99µA
±999.9µA
±9.999mA
±99.99mA
Measurement Range
Display
Input
Protection
Accuracy
(23°C±5°C,35~85%RH)
25
26
999.9mA
5A
offset
±9999
full scale ±9999
3A
8A
Minimum display
Display
Input
Protection
offset
±9999
full scale ±9999
±50V
±50V
±250V
±250V
±700V
Accuracy
(23°C±5°C,35~85%RH)
■ A6XX2-XX
Range
Range
Display
Input
Protection
Accuracy
(23°C±5°C,35~85%RH)
offset
±9999
full scale ±9999
±10mA
±10mA
±50mA
±500mA
50 digits
Resistance
■ A6XX7-XX
Range
Measurement Range
Display
Current
Accuracy
(23°C±5°C,35~85%RH)
11
12
13
14
99.99Ω
999.9Ω
9.999kΩ
99.99kΩ
offset
±9999
full scale ±9999
5mA
0.5mA
50µA
5µA
Measurement method: Two or Four wire (internal socket changable)
■ A6XX3-XX
64
Range
Measurement Range
Display
Input
Protection
Accuracy
(23°C±5°C,35~85%RH)
25
26
±999.9mA
±2.000A
offset
±9999
full scale ±9999
±3A
A6000
Thermocouple · RTD
Output Specification
■ A6XX8-XX
Range
Sensor type
Measurement
Range
Maximum
Resolution
Accuracy
(23°C±5°C,35~85%RH)
KA
KB
J
T
S
R
B
PA
PB
K
K
J
T
S
R
B
PT100Ω
PT100Ω
–50.0 to 199.9°C
–50 to 1200°C
–50 to 1000°C
–50 to 400°C
0 to 1700°C
–10 to 1700°C
100 to 1800°C
–100.0 to 199.9°C
–100 to 600°C
0.1°C
1°C
1°C
1°C
1°C
1°C
1°C
0.1°C
1°C
± (0.5% of FS)
± (0.2% of FS)
± (0.2% of FS)
± (0.6% of FS)
± (0.4% of FS)
± (0.4% of FS)
± (0.4% of FS)
± (0.15% of FS)
± (0.3% of FS)
Cold junction compensator accuracy : ±2°C(10 to 40°C)
Sensor lead resistance:
: less than 50Ω
Linearzing method:
Burn out alarm:
:----Conversion time:
: 2.5times/sec
■ HI & LO setpoints output (A6XXX-1X Reply output)
(A6XXX-2X Photocoupler)
Comparative condition
Option
■ External control (A6XXX-X1)
Start/Hold
: shorted between COM terminal or same level hold
Open COM terminal and start/hold terminal or 5 V start
D.ZERO
: Shorted between COM terminal and D.ZERO terminal ON
P.HOLD
: Shorted between COM terminal and P.HOLD terminal ON
R.RE(relay reset) : Shorted between COM terminal and R.RE terminal ON
P.SEL1 to 3
: as below
Frequency
■ A6XX9-XX
Range
Measurement Range
Accuracy
(23°C±5°C,35~85%RH)
11
12
13
0.1 to 999.9Hz
1 to 9.999kHz
10 to 99.99kHz
±(0.2% of FS)
P.SEL1
P.SEL2
P.SEL3
Input voltage level
Input Protection
Open collector
Logic
Magent
Voltage
L:less than 1.5V(5V, pullup)
L:less than 1V, HI:2.5 to 15V
0.3 to 30V P-P
30V to 500V rms
30V
15V
30V
500V
Prescale
: 0.01~10.00
PPR
: 1~100
Power supply for sensor : 12VDC±10%
■ BCD output (A6XXX-X2 TTL)
(A6XXX-X3 Open collector)
Type of output:
Logic:
Output rate:
0 to 1V
0 to 10V
1 to 5V
4 to 20mA
Strain gauge
■ A6XXA-XX
Zero adjustment Span adjustment
range
range
1 to 3mV/V
Measurement
range
Accuracy
–4~+4mV/V
±(0.1% of FS)
+2 digit
Sensor
: 350 Ω
Power supply for sensor : 5 V±5% (less than 15 mA)
Conversion speed
: 1000/sec
Display
1V
2V
2A
3A
1 to 5V
±5V
4 to 20mA
±20mA
offset
±9999
Excitation power supply: 12VDC ± 5%
24VDC ± 5% 25mA
Ripple
more than 10kΩ
±(0.5% of F.S)
50mV p-p
less than 550Ω
25mV p-p
Output method : PWM method
Scaling
: Digital scaling
Resolution
: 13 bit
Reponse time : approx 0.5sec
■ RS232C (Conforming to EIA RS-232C)(A6XXX-X5)
■ A6XXB-XX
Measurement
Range
Accuracy
Communication method : Full duplex
Transmission speed
: 4800/9600/19200/38400 bps
Start bit
: 1 bit
Data length
: 7 bit/8 bit
Parity
: Even parity/ odd parity/ none
Stop bit
: 1 bit/2 bit
Character code
: ASCII code
Transmission control process : Ignord process
Process
Range
Load resistance
A6000
–1 to +1mV/V
Open collector or TTL
Changeable
DC30V 10mA(open collector)
Funout 2(TTL)
■ Analog output (A6XXX-X4)
Output
5V
10V
pattern 1 pattern 2 pattern 3 pattern 4 pattern 5 pattern 6 pattern 7 pattern 8
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON : Shorted between COM terminal and P.SEL terminal or same level
OFF : Open between COM terminal and P.SEL terminal or 5 V
Input type
Sensor
HI
GO
LO
Indication > High setpoint
> Indication =
> Lo setpoint
High setpoint =
Indication < Lo setpoint
Setting range
: -9999 to 9999
Hysteresis
: 1 to 999 digit for each setpoints
Relay contact capacity : AC250 V 2 A resistive load
DC30 V 2 A resistive load
Photocoupler capacity : DC30 V 20 mA
Accuracy
±(0.03% of rdg +2digit)
±(0.1% of rdg +3digit)
■ RS-485 (conforming to EIA RS-485)(A6XXX-X6)
Communication method : Full duplex
Transmission speed
: 4800/9600/19200/38400 bps
Start bit
: 1 bit
Data length
: 7 bit/ 8 bit
Parity
: Even parity/ odd marity/ none
Error detection
: BCC
Stop bit
: 1 bit/2 bit
Character code
: ASCII code
Transmssion control process : Ignord process
Signal name
: +non reversal output
- reversal output
Maximum no of meter connected : 31
Line length
: up to 500m in total
65
A6000
■ Dimensions
■ Ordering Code
A6 씲씲씲-씲씲
(86.5)
77
(97.5)
0.5
Option
Input
Option
Power
10.9
Comparator
0. none
1. External control
2. BCD output (TTL)
3. BCD output (open collector)
4. Analog output
5. RS-232C
6. RS-485
7. RS-232C, analog output
8. RS-485, analog output
Comparator output 0. none
1. Relay
2. Photocoupler
44.8
91.5
102.5
Input
1. DC voltage
2. DC current
3. DC current
4. AC voltage
5. AC current
6. AC current
7. Resistance
8. Temperature (T/C, RTD)
9. Frequency
A. Strain gauge
B. Process
Display board
1. Multiple
2. Single
Power supply
1. AC 100 to 240 V
2. DC12 to 48 V
48
(21.5)
Multiple
96
92 +0.8
-0
MIN.70
45 +0.6
-0
Single
A6000
MIN.120
66
MEMO
67
MEMO
68
TERMINAL TYPE TRANSMITTER
TZ-1X
■ Features
!
NEW
・ AC power supply 100 to 240VAC
・ DIN rail mounting
・ Input/Output/Power supply isolated
■ Ordering Code
■ Input specifications
Input signal
DC 0 to 5V
DC 1 to 5V
DC 0 to 10V
DC –10 to 10V
DC 0 to 1V
DC 0 to 0.1V
DC 0 to 0.06V
DC 0 to 20V
DC –2 to 2V
DC –5 to 5V
DC 4 to 20mA
DC 0 to 20mA
Input Resistance
Allowable input
TZ -1X-씲씲씲
more than 1MΩ
Response time
L. 50msec
H. 1msec
Output
0.
1.
2.
3.
A.
Y.
DC 0 to 5V
DC 1 to 5V
DC 0 to 10V
DC -10 to 10V
DC 4 to 20mA
special
Input
0.
1.
2.
3.
4.
5.
6.
7.
8.
9.
A.
B.
Y.
DC 0 to 5V
DC 1 to 5V
DC 0 to 10V
-10 to 10V
DC 0 to 1V
DC 0 to 0.1V
DC 0 to 0.06V
DC 0 to 20V
DC -2 to 2V
DC -5 to 5V
DC 4 to 20mA
DC 0 to 20mA
special
-50 to +150%F.S
250Ω
special
Special Voltage input: DC -250V to 250V span 0.06 to 500V
Current input: DC 0 to 50mA span DC 1mA to 50mA
Special
Output load resistance
Output signal
DC 0 to 5V
DC 1 to 5V
DC 0 to 10V
DC –10 to 10V
DC 4 to 20mA
more than 2kΩ
more than 4kΩ
less than 550Ω
special
Voltage output: DC -10 to 10V span 0.06 to 20V
Current output: DC 0 to 20mA span 1 to 20mA
Input Signal
Code No.
0
1
2
3
A
Y
6
5
4
3
2
1
Load
Code No.
0
1
2
3
4
5
6
7
8
9
A
B
Y
8
7
Power
Supply(AC)
Caution: Be polarity careful
■ Block Diagram
Isolation AMP ZERO SPAN
3(+)
Input Signal
5(+)
Input
Circuit
Output
Circuit
Output Signal
6(-)
4(–)
1
NC
2
AC 100V
■ Dimensions
Transmitter
6
8
7
4
5
2
98.1
3
25
Front
94
Terminal Cover
Side
Slide Bar
37.3
40.8
Case Material:
Weight:
±0.1% F.S (25˚C±2˚C)
±0.06% F.S
±0.06% F.S
±0.02% F.S/˚C
50msec or 1msec(TYP) (0 to 90%)
±5% F.S or more (zero and span)
input/output/power supply, more than 100MΩ
input/output/power supply, AC2000V/1 min.
100 to 240VAC±10%
less than 30mA (at 100VAC)
-5 to 50˚C
Less than 90% RH
Black ABS
Approx. 100g
1
Accuracy:
Fluctuating power source:
Fluctuating load:
Temp. Coefficient:
Response time:
Adustable volume range:
Insulated Resistance:
Power supply:
Power consuption:
Operating Temp:
Power Supply Circuit
47
98
35.2
69
TZ-1B
■ Features
!
NEW
■ Ordering Code
Input range
100 to 10kΩ (span range 50% or more)
Dip switch for only available input code 1
SW1 ON: 0 to 100% (span adjust range 95 to 105%)
1. 0 to 100%
Y. special
less than 550Ω
Special
MAX
±0.1% F.S (25˚C±2˚C)
±0.06% F.S
±0.06% F.S
±0.02% F.S/˚C
50msec(TYP) (0 to 90%)
less than ±2% (0 to 100% at deliver)
100 to 240VAC±10%
-5 to 50˚C
Less than 90% RH
Black ABS
Approx. 100g
6
5
4
3
2
1
8
7
MIN
Load
more than 4kΩ
Case Material:
Weight:
Input
Power
Supply(AC)
■ Block Diagram
4
Base Circuit
3
Input
Circuit
5(+)
Output
Circuit
Output Signal
6(-)
2
more than 2kΩ
Accuracy:
Fluctuating load:
Temp. Coefficient:
Response time:
Change setting error:
Power supply:
Power consuption:
Operating Temp:
DC 0 to 5V
DC 1 to 5V
DC 0 to 10V
DC -10 to 10V
DC 4 to 20mA
special
Output signal
DC 0 to 5V
DC 1 to 5V
DC 0 to 10V
DC –10 to 10V
DC 4 to 20mA
Potentiometer
Code No.
0
1
2
3
A
Y
Output
0.
1.
2.
3.
A.
Y.
Special
TZ -1B-씲씲
0 to 100%
Potentiometer
Special
Potentiometer
100 to 10kΩ
special
Output Signal
Code No.
1
Y
1
AC 100V
■ Dimensions
8
7
25
6
4
3
5
2
1
Transmitter
98.1
Front
94
Side
Slide Bar
47
98
35.2
70
37.3
40.8
Terminal Cover
TZ-1D
■ Features
!
NEW
■ Ordering Code
Input Resistance
Allowable input
less than 0.05Ω
less than 7.5A
(15A, within 1ms)
special
TZ -1D-씲씲
Less than AC 0 to 5A span 1 to 5A
Input Frequency 40hz to 1kHz
more than 2kΩ
Load
8
7
Power
Supply(AC)
■ Block Diagram
ZERO SPAN
5(+)
3
T-RMS
set-up
diagram
Input Signal
6
Output
Circuit
Output Signal
6(-)
CT
±0.15% F.S (5 to 100% F.S)
±0.5% F.S (0 to 5% F.S)
25˚C±2˚C
±0.06% F.S
±0.06% F.S
±0.2% F.S(60Hz)
±0.02% F.S/˚C
Less than 700msec (TYP) (0 to 90%)
100 to 240VAC±10%
Less than 30mA (at 100VAC)
-5 to 50˚C
Less than 90% RH
Black ABS
Approx. 100g
1
NC
2
AC 100V
■ Dimensions
4
8
2
25
Front
Transmitter
3
98.1
1
94
Terminal Cover
Side
Slide Bar
37.3
40.8
Case Material:
Weight:
6
5
4
3
2
1
Output Signal
less than 550Ω
special
Fluctuating load:
Fluctuating frequency:
Temp. Coefficient:
Response time:
Power supply:
Power consuption:
Operating Temp:
1. AC 0 to 1A
2. AC 0 to 5A
Y. special
more than 4kΩ
Accuracy:
Input
7
Special
DC 0 to 5V
DC 1 to 5V
DC 0 to 10V
DC -10 to 10V
DC 4 to 20mA
special
Output signal
DC 0 to 5V
DC 1 to 5V
DC 0 to 10V
DC –10 to 10V
DC 4 to 20mA
Input Signal
Code No.
0
1
2
3
A
Y
Output
0.
1.
2.
3.
A.
Y.
6
Special
Input signal
AC 0 to 1A
AC 0 to 5A
5
Code No.
1
2
Y
47
98
35.2
71
TZ-1E
■ Features
!
NEW
■ Ordering Code
Input signal
AC 0 to 35V
AC 0 to 100V
AC 0 to 110V
AC 0 to 200V
AC 0 to 220V
Input Resistance
Allowable input
more than 1MΩ
less than 150%
(Max. AC250V)
TZ -1E-씲씲
Output
0.
1.
2.
3.
A.
Y.
DC 0 to 5V
DC 1 to 5V
DC 0 to 10V
DC -10 to 10V
DC 4 to 20mA
special
Input
1.
2.
3.
4.
5.
Y.
AC 0 to 35V
AC 0 to 100V
AC 0 to 110V
AC 0 to 200V
AC 0 to 220V
special
special
Special Voltage input: AC 0 to 250V span 4 to 250V
Input Frequency
: 40Hz to 1KHz
more than 2kΩ
more than 4kΩ
less than 550Ω
special
Voltage output: DC -10 to 10V span 1 to 20V
6
5
4
3
2
1
Load
Special
Output signal
DC 0 to 5V
DC 1 to 5V
DC 0 to 10V
DC –10 to 10V
DC 4 to 20mA
Input Signal
Code No.
0
1
2
3
A
Y
8
7
Power
Supply(AC)
Output Signal
Code No.
1
2
3
4
5
Y
Fluctuating load:
Fluctuating frequency:
Temp. Coefficient:
Response time:
Power supply:
Power consuption:
Operating Temp:
■ Block Diagram
3(+)
Input Signal
4(-)
5(+)
T-RMS
set-up
diagram
Output
Circuit
Output Signal
6(-)
1
NC
2
AC 100V
■ Dimensions
Transmitter
Case Material:
Weight:
±0.15% F.S (5 to 100% F.S)
±0.5% F.S (0 to 5% F.S)
25˚C±5˚C
±0.06% F.S
±0.06% F.S
±0.2% F.S (60Hz)
±0.02% F.S/˚C
less than 700msec(TYP) (0 to 90%)
100 to 240VAC±10%
-5 to 50˚C
Less than 90% RH
Black ABS
Approx. 100g
Accuracy:
6
8
7
4
3
5
2
1
98.1
25
Front
94
Side
Slide Bar
47
98
35.2
72
37.3
40.8
Terminal Cover
TZ-1F
!
NEW
■ Features
■ Ordering Code
Allowable input
TZ -1F-씲씲씲
Response time
L. 50msec
H. 3msec
Output
0.
1.
2.
3.
A.
Y.
DC 0 to 5V
DC 1 to 5V
DC 0 to 10V
DC -10 to 10V
DC 4 to 20mA
special
Input
0.
1.
2.
3.
4.
A.
B.
C.
Y.
DC 0 to 5mV
DC 0 to 10mV
DC 0 to 50mV
DC 0 to 60mV
DC 0 to 100mV
DC 0 to 10µA
DC 0 to 100µA
DC 0 to 200µA
special
more than 1MΩ
-50 to +150%F.S
more than 1KΩ
less than 500Ω
special
Voltage input: DC -100mV to 100mV span DC 5 to 200mV
Current input: DC -5mA to 5mA span DC 10µA to 10mA
more than 2kΩ
span 0.06 to 20V
span 1 to 20mA
2
1
Power
Supply(AC)
■ Block Diagram
3(+)
Input Signal
5(+)
Input
Circuit
Output
Circuit
Output Signal
6(-)
4(–)
1
NC
2
AC 100V
Transmitter
■ Dimensions
4
8
2
98.1
3
25
Front
94
Terminal Cover
Side
Slide Bar
37.3
40.8
Case Material:
Weight:
8
7
±0.1% F.S (25˚C±2˚C)
±0.06% F.S
±0.06% F.S
±0.02% F.S/˚C
50msec or 3msec(TYP) (0 to 90%)
100 to 240VAC±10%
-5 to 50˚C
Less than 90% RH
Black ABS
Approx. 100g
1
Accuracy:
Fluctuating load:
Temp. Coefficient:
Response time:
Power supply:
Power consuption:
Operating Temp:
6
5
4
3
Load
less than 550Ω
special
Voltage output: DC -10 to 10V
Current output: DC 0 to 20mA
more than 4kΩ
7
Special
Output signal
DC 0 to 5V
DC 1 to 5V
DC 0 to 10V
DC –10 to 10V
DC 4 to 20mA
Input Signal
Code No.
0
1
2
3
A
Y
6
Special
Input Resistance
Input signal
DC 0 to 5mV
DC 1 to 10mV
DC 0 to 50mV
DC 0 to 60mV
DC 0 to 100mV
DC 0 to 10µA
DC 0 to 100µA
DC 0 to 200µA
5
Code No.
0
1
2
3
4
A
B
C
Y
47
98
35.2
73
PROGRAMMABLE TRANSMITTER
TW-3M
■ Features
・ Can change input and output by front Dip switch
・ 100 to 240 VAC or 24 VDC power supply
・ DIN rail mount type
(C Type)
(N Type)
■ Input Specification
■ Dimensions
Input signal
0 to 5 VDC
1 to 5 VDC
0 to 10 VDC
0 to 60 mVDC
4 to 20 mADC
0 to 20 mADC
Input resistance
Sliding from 96 to 98
SPAN
SW2
20
ZERO
4.5
Side view
41
64.5
94
Allowable load resistance
More than 2 kΩ
More than 2 kΩ
More than 4 kΩ
Less than 550 Ω
Less than 550 Ω
35.2
18
Output signal
0 to 5 VDC
1 to 5 VDC
0 to 10 VDC
4 to 20 mADC
0 to 20 mADC
12345678
SW1
ON
OFF
ON
OFF
48
Front view
1234
250 Ω
ZERO/SPAN
adjusters
I/Orange
setting Dip
SWs.
More than 1 MΩ
35.4
Linearity:
Temperature characteristic:
Response time:
Insulantion resistance:
Power supply:
Power comsumption:
Operationg temperature:
Operating humidity:
Case material:
Weight:
Less than ± 0.1% F.S
± 0.02% F.S/°C
Less than 50ms ( 0 to 90%)
Between input and output or power supply,
more than 100MΩ
Between input and output or power supply,
for 1 min. at 2000VAC
24VDC ±10%
100-240VAC ±10%
Less than 80mA (at 24VDC)
Less than 50mA (at 100-240VAC)
-5 to 50°C
Less than 90%
(No dew-condensing)
Black PBT 94-V0
Approx. 130g
Input
signal
6
12
5
11
4
10
3
9
2
8
1
7
Isolated Amp.
Transmitter
-
Input
circuit
ZERO SPAN
Output
circuit
C: Connector (screw) Type (UL available)
N: Screw Type
Power circuit
■ Setting or changing input/output range
0-10V
0-60mV
4-20mA
0-20mA
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
74
2. Setting or changing output range
SW1
SW2
ON
0-5V
OFF
1-5V
0-10V
4-20mA
0-20mA
ON
OFF
ON
OFF
ON
OFF
ON
OFF
1 2 3 4
1 2 3 4
7
Output signal
8
11
Power
12
1: 100 - 240VAC
4: 24VDC (CE available)
1-5V
Output
signal
■ Block Diagram
5
Input signal
6
1. Setting or changing input range
SW1
SW2
ON
0-5V
OFF
Power
(DC)
Note: When conducting wiring, be careful with its polarity.
■ Ordering Code
TW-3M -
Power
(AC)
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
TRANSMITTER WITH ONE INPUT AND TWO OUTPUTS
TW-2X
■ Features
・ DIN rail mount
・ 2 outputs
・ Input/output1/output2/power supply Isolated
(C Type)
(N Type)
■ Ordering Code
TW-2X -
-4-
C: Connector (screw) Type
N: Screw Type
0: 0 - 5V DC
1: 1 - 5V DC
2: 0 - 10V DC
Second Output code
A: 4 - 20mA DC
B: 0 - 20mA DC
Y: Special
A: 4 - 20mA DC
First Output code
Y: Special
0: 0 - 5V DC
1: 1 - 5V DC
2: 0 - 10V DC
Input code
A: 4 - 20mA DC
B: 0 - 20mA DC
Y: Special
Limit of Y specifications
Voltage input : 250VDC or less , Minimum span ; 100mVDC
Current input : 50mADC or less , Minimum span ; 1mADC
■ First output specifications
Current output : 20mADC or less , Minimum span ; 1mADC
Voltage output : From -10VDC to +10VDC
Minimum span ; 1VDC
Signal
input
■ Second output specifications
Output signal
Load resistance
0-5V DC
Less than 2K ohm
1-5V DC
0-10V DC
Less than 4K ohm
4-20mA DC
Less than 550 ohm
0-20mA DC
Other than the above
Current output : 20mADC or less , Minimum span ; 1mADC
Voltage output : From -10VDC to +10VDC
Minimum span ; 1VDC
+
TW-2X
12
11
10
9
8
7
-
DC
24V
+
- Signal
+
output2
Note: Pay attention to the connection polarity.
■ Block Diagram
TW-2X
5(+)
Signal
input
6(–)
3
NC
4
1(+)
Signal
output 1
2(–)
Isoration Amp.
Input
circuit
Isolation Amp.
ZEROSPAN
ZEROSPAN
Output
circuit
1
Output
circuit
2
11(+)
DC 24V
12(–)
9
NC
10
7(+)
Signal
output 2
8(–)
■ Dimensions
64.5
Front view
Transmitter
±0.25% FS
±200 ppm FS/℃ (TYP)
Less than 50msec ( 0 to 90%)
Between input and/output 1/output 2/power ;
More than 100MΩ (at 500VDC)
Between input and/output 1/output 2/power ;
For 1 min. at 2000VAC
Power supply voltage:
24VDC ±10%
Current comsumption:
Less than 110mA
Operationg ambient temperature: -5 to 50℃
Operating ambient humidity: Less than 90% RH (No condensing)
Weight:
Approx. 130g
Accessories:
Instruction manual
Terminal cover
Detachable 6-P connector
94
96∼98
17.4
41
Side view
35.4
With
terminal
cover
4.3
Accuracy:
Response time:
Insulantion resistance:
+
6
5
4
3
2
1
42.5
Code No.
0
1
2
A
B
Y
Signal
output1
-
20
48
Output signal
Load resistance
4-20mA DC
Less than 550 ohm
Power circuit
Code No.
A
Y
SPAN
Intput signal
Input resistance
0-5V DC
1-5V DC
More than 1M ohm
0-10V DC
4-20mA DC
250 ohm
0-20mA DC
OUT 2 SPAN
OUT 1
Code No.
0
1
2
A
B
Y
ZERO
OUT 2 ZERO
OUT 1
75
Transmitter With Two Outputs
TW-2XA
■ Featuers
• DIN Rail m ount
• AC Power Supply 100 to 240V AC±10%
• 2 Outputs
■ Input Specifications
Code No.
0
1
2
A
Y
■ Ordering Code
Input
0 to 5V DC
1 to 5V DC
0 to 10V DC
4 to 20mA DC
Input Resistance
TW-2XA-
-1
more than 1M Ω
2nd output
0.
1.
2.
A.
Y.
0 to 5V DC
1 to 5V DC
0 to 10V DC
4 to 20mA DC
Special
1st output
0.
1.
2.
A.
Y.
0 to 5V DC
1 to 5V DC
0 to 10V DC
4 to 20mA DC
Special
Input
0.
1.
2.
A.
Y.
0 to 5V DC
1 to 5V DC
0 to 10V DC
4 to 20mA DC
Special
250 Ω
Special
Y specification
Input voltage: less than 250V DC min span 0.1V DC
Input Curent: less than 50mA DC min. span 1mA DC
■ Output Specifications (1st, 2nd output)
Output signal
0 to 5V DC
1 to 5V DC
0 to 10V DC
4 to 20mA DC
Load Resistance
more than 2K Ω
more than 4K Ω
less than 550 Ω
■ Dimensions
64.5
Special
Y specification
Output voltage: less than ±10V DC min. span 1V DC
Output Curent: less than 20mA DC min. span 1mA DC
Front
48
20
Code No.
0
1
2
A
Y
■ General Specification
Power supply:
Power comsumption:
Weight:
Accessory:
96 to 98 Slide
41
94
±0.25% F.S (25˚C±2˚C)
±0.02% F.S/˚C
less than 50msec (0 to 90%)
Between input and output 1, output 2, power
supply more than 100M Ω (500V DC)
Between input and output 1, output 2, power
supply 1500V AC per 1 min.
100 to 240V AC ±10%
–5 to 50˚C less than 90%RH (No
condensing)
Less than 45mA at 100V AC
Less than 30mA at 200V AC
Approx. 130g
Instruction manual, terminal cover
Side
17.4
4.3
Accuracy:
Temperature Characteristic:
Response time:
35.4
Input
Transmitter
TW–2XA
–XXX–1
Output 1
Power Supply
(AC)
Output 2
■ Block Diagram
Input
Input
Circuit
Power Supply
Input
Circuit
Output 1
76
ZERO SPAN
ZERO SPAN
Output
Circuit 1
Output
Circuit 2
Output 2
Temperature Transmitter With Two Outputs
TW-2C
■ Featuers
• DIN Rail Mount
• AC Power Supply 100 to 240V AC ±10%
DC Power Supply 24V DC ±10%
• 2 Outputs
• Sensor Type: R,K,E,J,T,S,B,PT-100 Ω
■ InputSpecification
Sensor
R
K
E
J
T
S
B
Pt 100 Ω
■ Ordering Code
Code
R
K
E
J
T
S
B
P
Input temperature
0 to 1700˚C
–50 to 1200˚C
–50 to 900˚C
–50 to 1000˚C
–50 to 350˚C
0 to 1700˚C
200 to 1700˚C
–150 to 800˚C
Minimum Span
400˚C
100˚C
100˚C
100˚C
100˚C
500˚C
1000˚C
100˚C
TW-2C-
Power supply
2nd output
1st output
Thermocouple Input Specification
Accuracy of Cold Junction Compensation ±1˚C (10 to 30˚C)
(For thermocouples other than B type thermocouple)
RTD lnput Specification
Allowable leadwire resistance: Less than 10Ω
Current following through RTD: 1mA
Input
1. 100 to 240 AC
4. 24V DC
0.
1.
2.
A.
0 to 5V DC
1 to 5V DC
0 to 10V DC
4 to 20mA DC
A. 4 to 20mA DC
Y. special
R
K
E
J
T
S
B
P
■ Dimensions
64.5
[1st output]
Code
A
Y
Output signal
4 to 20mA DC
Output Load resistance
less than 550 Ω
Special
Output at burnout
20
Front
Approx. 120% F.S
94
Y specification
more than 2K Ω
Output at burnout
Approx. 120% F.S
more than 4K Ω
Side
17.4
Y
Output signal
0 to 5VDC
1 to 5VDC
0 to 10VDC
41
Code
96 to 98 Slide
[2nd output]
Output at burnout
more than 2K Ω
more than 4K Ω
less than 550 Ω
Approx. 120% F.S
Terminal
Cover
4.3
Output signal
0 to 5V DC
1 to 5V DC
0 to 10V DC
4 to 20mA DC
42.4
Code
0
1
2
A
35.4
Power supply:
Power consumption:
Weight:
Accessory:
±0.25% F.S
±200ppmF.S/˚C(TYP)
less than 2 sec (0 to 90%)
Between Input and output/power supply
more than 100M Ω (500V DC)
Between Input and output/power supply
1500V AC per 1 min.
100 to 240V AC ±10%
24V DC ±10%
Less than 110mA at DC
Less than 50mA at AC
–5 to 50˚C less than 90%RH (No
condensing)
Approx. 160g
Instruction manual, terminal cover, 6P
connector
RTD
TC
Transmitter
Accuracy:
Response time:
Power
Supply
TW–2C
Input
1st Output
2nd Output
■ Block Diagram
Burnout Circuit
(+)4
(–)5
Input
(–)6
7(+)
8(–)
1st
Output
Circuit
10(–)
Power Supply
Cold Junction
Compensation
MPU
2nd
Output
Circuit
9(+)
11
12
77
Digital Alarm Setter
TW-3R
■ Featuers
• DIN rail mount
• Hi and Lo setpoints
• Power supply 24V DC
■ DC voltage measurement
Range
0
1
2
Measurment
0 to 5V
1 to 5V
0 to 9.999V
Display
Offset ± 9999
Fullscale
± 9999
■ Ordering Code
Input impedance
1M Ω
1M Ω
1M Ω
Input Protection
TW-3R-
± 250V
Comparator output
1.
2.
0.
Range 1.
2.
A.
Accuracy: ± (0.1% of rdg +2 digit) (23˚C ± 5˚C 35 to 85%RH)
Relay
Photo Coupler
0 to 5V DC
1 to 5V DC
0 to 9.999V DC
4 to 20mA DC
■ DC current measurement
A
4 to 20mA
Display
Offset ± 9999
Fullscale
± 9999
Input impedance
Input Protection
50 Ω
± 60mA
64.5
M
94
96∼98 Slide
17.4
41
Side
35.4
Terminal Cover
● Common Section
Transmitter
Excitation supply :
Accessories :
C
HI
e
Relay
COM
C
Photocoupler
LO
NC
DC24V
−
Case material :
Insulation resistance :
EEPROM (rewrite 100,000times)
0 to 50˚C 35 to 85%RH
-10 to +70˚C less than 60%RH
24V DC ± 20%
70mA (TYP) at 24V DC
48mm (W) ✕ 98mm (H) ✕ 41mm (D)
approx. 140g (unit only)
Input (LO) and comparator output 500V DC
per min.
Power supply (0V) and input (LO),
comparator output case, 1500V AC per min.
Input (LO) and case, 1500V AC per min.
Black PBT
500V DC 500M ohm or more as the above
terminals
24V DC ± 10% 25mA ripple less than
200mVp-p
Instruction manual. terminal cover,
connector
＋
Memory backup :
Operating temp. :
Storage temp. :
Power supply :
Power consumption :
Dimensions :
Weight :
42.4
Single ended
12.5times/sec (50Hz), 15times/sec (60Hz)
NMR40dB or more (50/60Hz)
Red LED 8mm height
Automatic “-” display when the computation
result is minus
display “o.L” or “-o.L”
± 9999 (4 digit)
± 100ppm/˚C
4.3
Maximum display :
Decimal point :
Zero display :
Temp. coeff. :
● Comparison Section
-9999 to +9999
By conversion rate
Hi setpoint < Measured value
→ HI
Hi setpoint Measured value Lo setpoint → GO
Measured value < Lo setpoint
→ LO
Relay output capacity:
30V DC/1A
resistive load
125V AC/0.5A resistive load
Photo coupler output capacity: Voltage max. 30V
Current max. 50mA
Saturation voltage less than 1.2V at 50mA
Control method:
Setting range:
Operating:
78
LO
▲
● Measuring Section
Overrange warning :
GO
Front
■ Specification
Conversion rate :
Noise rejection ratio :
Display :
Polarity display :
HI
E
Accuracy: ± (0.1% of rdg +2 digit) (23˚C ± 5˚C 35 to 85%RH)
■ Dimensions
20
Measurment
▲
Range
TW–3R
NC
NC
+24V
0V
HI Input
LO
Transmitter
TH-1X
■ Features
・Easy to change input/output code (SJ)
・Slim width 12.5 mm
・DIN rail mount type
・24 VDC power supply
■ Dimensions
DC voltage & current
12.5
6
8
5
7
ZERO
SPAN
3
more than 1MΩ
59±0.5
Side
115±0.5
Output signal
DC 0 to 5 V
DC 1 to 5 V
DC 0 to 10 V
DC -10 to 10 V
DC 4 to 20 mA
special
Load resistance
more than 2KΩ
more than 2KΩ
more than 4KΩ
more than 4KΩ
less than 550Ω
TOKYO JAPAN
MODEL
INPUT
OUTPUT
POWER
LOT No.
TAG No.
DC voltage & current
7 8
＋ − POWER
5 6
＋ − OUTPUT
TH-IX-00
DCO∼5V
DCO∼5V
DC24V
0105A
■ Output specification
ASAHI KEIKI
＋ −
3 4 INPUT
250Ω
Special: Voltage input less than 250 V DC, min span 0.1 V
Current input less than 50 mA DC, min span 5 mA DC
Code No.
0
1
2
3
A
Y
4max
99±0.5
Front
4
Input resistance
TH-1X
Input signal
DC 0 to 5 V
DC 1 to 5 V
DC 0 to 10 V
DC -10 to 10 V
DC 0 to 1 V
DC 0 to 0.1 V
DC 4 to 20 mA
special
TAG
Code No.
0
1
2
3
4
5
A
Y
Special: Voltage input less than ±10 V DC, min span 1 VDC
Current input less than 20 mA DC, min span 5 mA DC
−
4
6
8
＋
3
5
7
−
DC
24V
LOAD
■ Ordering Code
DIN rail
output
±0.25% F.S
±0.02% F.S/°C
less than 20 msec (0 to 90%TYP)
input/output/power supply, AC 1500V/1 min.
24 V DC±10%
less than 60 mA
-5 to 50°C less than 90%RH
99 mm (H)×12.5 mm(W)×115 mm(D)
input
Accuracy:
Temp. Coefficient:
Response Time:
Power Supply:
Power consumption:
Operating Temp.:
Size:
（4）
■ General specification
＋
TH-1X- □ □
Transmitter
0. DC 0 to 5 V
Output code 1. DC 1 to 5 V
2. DC 0 to 10 V
3. DC -10 to 10 V
A. DC 4 to 20 mA
Y. special
0. DC 0 to 5 V
Input code 1. DC 1 to 5 V
2. DC 0 to 10 V
3. DC -10 to 10 V
4. DC 0 to 1 V
5. DC 0 to 0.1 V
A. DC 4 to 20 mA
Y. special
79
Temperature Transmitter
TH-1C
■ Featuers
・Slim width 12.5mm
・Power supply 24VDC ±10%
・Input sensor
R,K,E,J,T,S,B, PT-100 ohm
■ Dimensions
Code
Input temperature
Minimum Span
R
K
R
0 to 1700°C
400°C
K
-50 to 1200°C
100°C
E
E
-50 to 900°C
100°C
J
J
-50 to 1000°C
100°C
100°C
T
T
-50 to 350°C
S
S
0 to 1700°C
500°C
B
B
200 to 1700°C
1000°C
Pt 100 Ω
P
-150 to 800°C
100°C
Front View
4
990.5
12.5 0.5
0
Sensor
590.5
Side View
Thermocouple Input Specification
Accuracy of Cold Junction Compensation ±1°C (10 to 30°C)
(For thermocouples other than B type thermocouple)
RTD Input Specification
1150.5
Allowable leadwire resistance: Less than 10 Ω
Current following through RTD: 1mA
Code
Output signal
0
DC 0 to 5 V
Output
Load resistance
Output at burnout
More than 2k Ω
1
DC 1 to 5 V
2
DC 0 to 10 V
More than 4k Ω
A
DC 4 to 20 mA
Less than 550 Ω
Approx 120% F.S
(4)
DIN rail (35mm Wlde)
6
8
5
7
6
8
5
7
T/C input
B
1
3
2
4
1
3
DC
24V
Load
4
Output signal
2
Load
Output signal
Transmitter
Accuracy:
±0.25% F.S (At 25±2°C)
Temperature characteristic: ±0.02% F.S/°C
Power supply voltage variation: ±0.1% F.S
Response Time:
Less than 2 sec (0 to 90%)
Between input and output/power supply;
More than 100 MΩ at 500 VDC
For 1 min. at 1500 VAC
Power supply voltage:
24V DC±10%
Consuming current:
Less than 60 mA (At 24 VDC)
Operating ambient temperature: -5 to 50°C
Operating ambient humidity: Less than 90%RH (No-condensing)
Storage temperature:
-10 to 70°C
Storage humidity:
Less than 60%RH (No-condensing)
Case material:
Black PC risin 94V-2
Weight:
Approx. 80g
B
Pt input
DC
24V
A
■ Ordering Code
Example: TH-1C-K0-1 0 to 1000°C
TH-1C- □ □ □
Accessory code
0. No accessory provided
1. Software and cable provided
0.
Output code 1.
2.
A.
0 to 5 VDC
1 to 5 VDC
0 to 10 VDC
4 to 20 mADC
R.
Input code 1. K.
E.
J.
T.
S.
B.
R Type (0 to 1700°C)
K Type (0 to 1200°C)
E Type (0 to 900°C)
J Type (0 to 1000°C)
T Type (0 to 350°C)
S Type (0 to 1700°C)
B Type (0 to 1700°C)
Can change
input sensor
2. P. RTD Pt (0 to 800°C)
As input specifications, separately specify the zero and span temperatures
(in steps of 1°C).
Otherwise, any one of the above temperatures is selected.
When purchasing only the setting soft cable, specify "TH-1C-XX-1."
80
Transmitter
TH-41
■ Featuers
・Self-powered
・1ch or 2ch input
・Slim width 12.5mm
■ Dimensions
Front View
6
8
TOKYO JAPAN
OUTPUT1
ASAHI KEIKI
OUTPUT2
7 8
5 6
3 4 INPUT2
MODEL TH-41-2
INPUT1 DC4 20mA
max. 30V 30mA
OUTPUT1 DC4 20mA
INPUT2 DC4 20mA
max. 30V 30mA
OUTPUT2 DC4 20mA
LOT No. 0105A
TAG No.
1 2 INPUT1
When using the TH-41, pay attention to the following.
The TH-41 can be used if the sum of voltage calculated by a voltage
loss of 3V across the TH-41 and that of RA X 20mA across a load
connected is smaller than the signal cource voltage.
5
7
TAG
2
4
1
3
TH-41
590.5
Side View
■ Operating Condition
4max
990.5
12.5 0.5
0
Input signal:
4 to 20mADC
Max. input current
30mADC
Max. output load:
1000 ohms
Voltage loss:
less than 3V
Response time:
20ms (0 to 90%)
Temperature characteristic: less than ±0.005%/°C
Accuracy:
±0.1% F.S
Operating temp.:
-5 to 50 °C
Operating ambient humidity: less than 90%RH (no condensing)
Storage temp.:
-10 to 70°C
Weight:
Approx. 80g
Between the input and output 2000VAC/1min.
Between the input and output or power supply
more than 100M ohms (at 500 VDC)
1150.5
■ Specifications
Voltage loss: 3V
Signal
source
20 mA
DIN rail (35mm Wlde)
Load
RA
TH-41
VA
(4)
20 mA
VA 3V 20 mA RA
6
8
3
5
7
Load
4
1
Load
2
Transmitter
Output signal CH2
Number of channels
1. 1 channel
2. 2 channel
Input signal CH1
TH-41- □
Input signal CH2
■ Ordering Code
Output signal CH1
81
Programmable Transmitter
TH-1M
■ Featuers
• Can change input and output by front dip switch
• DIN Rail mount
■ Setting or changing input/output range
1. Setting or changing input range
SW1
1-5V
0-10V
0-60mV
4-20mA
0-20mA
1-5V
0-10V
4-20mA
0-20mA
1234
SW2
1234
12345678
12345678
Front
4max
99±0.5
–0
59±0.5
Side
115±0.5
Setting range at factory:
Input 1 to 5 V DC, Output 4 to 20mA DC
Accuracy:
±0.25% F.S (25˚C±2˚C)
After changed input range error:
±1% F.S
After changed output range error:
±1% F.S
Temperature characteristic: ±0.02% F.S/˚C
Response time:
less than 15ms (0 to 90%)(TYP)
Between input and output/power supply
more than 100M ohm at 500V DC
Between input and output/power supply
1500V AC per 1min.
Power supply:
24 V DC ±10%
Power consumption:
Less than 80mA
–5 to 50˚C Less than 90%RH (No
condensing)
Weight:
Approx. 80g
Approval:
EN61000-6-2, EN55011
Accessory:
Switch sheet
SW1
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
■ Dimensions
12.5
Allowable load resistance
More than 2 k Ω
More than 2 k Ω
More than 4 k Ω
Less than 550 Ω
Less than 550 Ω
+0.5
Output signal
0 to 5 V DC
1 to 5 V DC
0 to 10 V DC
4 to 20 mA DC
0 to 20 mA DC
0-5V
5 6
7 8
250 Ω
2. Setting or changing output range
SW2
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ZERO
More than 1 MΩ
0-5V
SPAN
Input resistance
3 4
Input signal
0 to 5V DC
1 to 5V DC
0 to 10V DC
0 to 60mV DC
4 to 20mA DC
0 to 20mA DC
TH-1M
TAG
(4)
■ Ordering code
TH-1M
DIN RAIL
Transmitter
Input
Output
DC
24V
■ Block Diagram
3(+)
Input
4(–)
Input
Circuit
Power Supply
Circuit
82
5(+)
Output
6(–)
Output
Circuit
7(+)
DC24V
8(–)
DISTRIBUTOR
TZ-5L
■ Features
• DIN rail mount
• Low cost
• Miniature Size
• Isolated Input/Output/Power supply
■ Dimensions
Input code
{
Front
5 max
94
54
DC 4~20mA
11.5
Output code
0: DC 0~5V
1: DC 1~5V
2: DC 0~10V
A: DC 4~20mA
Y: Special
25
■ Ordering Code
TZ-5L-A
63
4-20mA DC (Input resistance 50Ω)
83
more than 2KΩ
more than 4KΩ
less than 550Ω
For code No. Y
Limit of specifications
Voltage output : Less than +10VDC and more than -10VDC
Minimum span : 1VDC
Current output : Less than 20mADC
Minimum span : 5mADC
Accuracy :
±0.25%F.S (23˚C±2˚C)
Temperature characteristic : ±200ppmF.S/˚C (TYP.)
Response time :
Less than 50 msec (0~90%)
Insulated resistance :
More than 100MΩ (at 500V DC)
For 1 min. at 2000VAC
Power supply voltage :
24V DC±10% less than 80mA
Operating ambient Temp. : -5 to +50˚C
Operating ambient humidity : Less than 90%RH(No-condersing)
Weight :
Approx. 80g
24~32VDC (No load resistance)
Less than 22mADC
Less than 30mADC
Short circuit duration : No limit
2
4
6
8
1
3
5
7
DC24V
Note : Pay attention to the connection polarity.
■ Block Diagram
Input
Circuit
Isolation
AMP
Zero Span
2(＋)
Input
Output
5(＋)
6(ー)
3(ー)
Transmitter
■ Powerr supply to 2-wire transmitter
LOAD
■ Specifications
Output voltage :
Current Capacity :
Current at short circuit :
Permissible :
41
Load resistance
Output Signal
DC0~5V
DC1~5V
DC0~10V
DC4~20mA
34.5
Output signal
25.5
0
1
2
A
Y
2-Wire
Transmitter
Code No.
Side
Output Circuit
1(+)
Excitation
Power
Supply
4(–)
7(＋)
DC24V
8(ー)
83
TZ-5H
■ Features
• Miniature size
• DIN rail mount
• Easy connection
■ Dimensions
Input resistance
8
4
6
2
98
94
54
3
*Code "Y" specifications
Voltage input: less than 250VDC (span 100mVDC)
Current input: less than 50mADC (span 1mADC)
7
11.5
25
Front
5
DC0~5V
DC1~5V
more than 1MΩ
DC0~10V
DC4~20mA
DC0~20mA
250Ω
Special
0
1
2
A
B
Y
1
Input signal
Code No.
63
83
25.5
DC0~5V
more than 2KΩ
DC1~5V
DC0~10V
more than 4KΩ
DC4~20mA
DC0~20mA
less than 550Ω
Special
0
1
2
A
B
Y
34.5
Side
Input resistance
Output signal
Code No.
41
■ Output Specifications
*Code "Y" specifications
Voltage output: less than ±10VDC (span 1VDC)
Current output: less than 20mADC (span 1mADC)
Accuracy:
Temp. Coefficient:
Response Time:
Power Supply:
Operating Temp:
Weight:
±0.25% F.S.
±200 ppm/°C F.S(Typ)
Less than 50msec(0 to 90%)
Input/Output/Power supply more than
100MΩ(500VDC)
Input/Output/Power supply 2000VAC/l min
24VDC ±10% less than 60mA
-5~+50°C, less than 90%RH
80g
2
4
6
8
1
3
5
7
DC24V
LOAD
INPUT
OUTPUT
■ Block Diagram
■ Ordering Guide
TZ-5H-
Transmitter
Output code 0. 0~5VDC
1. 1~5VDC
2. 0~10VDC
A. 4~20mADC
B. 0~20mADC
Y. Special
Input code
84
0. 0~5VDC
1. 1~5VDC
2. 0~10VDC
A. 4~20mADC
B. 0~20mADC
Y. Special
Input
Circuit
3(＋)
Input
4(ー)
Isolation
Zero Span
AMP
Output
5(＋)
6(ー)
Output Circuit
7(＋)
DC24V
8(ー)
1
N.C
2
TZ-5X
■ Features
• DC Power supply 24VDC
• DIN rail mounting
• Input / Output / Power supply isolated
■ Ordering Code
Input Resistance
Allowable input
TZ-5X-
0. DC 0 to 5V
1. DC 1 to 5V
2. DC 0 to 10V
3. DC –10 to 10V
6. DC 0 to 4V
A. DC 4 to 20mA
Y. special
Output
more than 1MΩ
–50 to +150%F.S
0. DC 0 to 5V
1. DC 1 to 5V
2. DC 0 to 10V
3. DC –10 to 10V
4. DC 0 to 1V
5. DC 0 to 0.1V
6. DC 0 to 4V
7. DC 0 to 20V
8. DC –2 to 2V
9. DC –5 to 5V
A. DC 4 to 20mA
B. DC 0 to 20mA
Y. special
250Ω
Special
Special Voltage input: DC less than 250V span 0.1V
Current input: DC less than 50mA span DC 1mA
Input
more than 2 kΩ
more than 4 kΩ
more than 2 kΩ
less than 550 Ω
Input Signal
Code No.
Output Signal
0
DC 0 to 5V
1
DC 1 to 5V
2
DC 0 to 10V
3
DC –10 to 10V
6
DC 0 to 4V
A
DC 4 to 20mA
Y
Special
Special Voltage output: DC -10 to 10V span DC 1V
Current output: DC 0 to 20mA span DC 1mA
–
2
1
+
6
5
4
3
–
8
7
–
DC
24V
Load
Input Signal
DC 0 to 5V
DC 1 to 5V
DC 0 to 10V
DC –10 to 10V
DC 0 to 1V
DC 0 to 0.1V
DC 0 to 4V
DC 0 to 20V
DC –2 to 2V
DC –5 to 5V
DC 4 to 20mA
DC 0 to 20mA
+
+
Output Signal
Code No.
0
1
2
3
4
5
6
7
8
9
A
B
Y
5
(+)
Output Signal
6
(–)
3(+)
Input Signal
Output
Circuit
Input
Circuit
4(–)
7
(+)
DC 24V
8
(–)
1
NC
2
Transmitter
■ Dimensions
8
7
25
6
4
5
2
94
3
Front
57.6
Terminal Cover
Side
Slide Bar
37.3
40.8
Case Material:
Weight:
■ Block Diagram
±0.1% F.S (25˚C±2˚C)
±200PPM F.S/˚C (TYP)
less than 50msec (0 to 90%)
240VDC±10%
less than 65mA (at 24VDC)
-5 to 50˚C
Less than 90% RH
Black ABS
Approx. 80g
1
Accuracy:
Temp. Coefficient:
Response time:
Power supply:
Power consuption:
Operating Temp:
47
98
35.2
85
TZ-41
■ Features
• Miniature Size
• Self-powered
• Easy Connection
• DIN rail mount
■ Specifications
■ Ordering Code
TZ-41
■ Dimensions
98
94
Front
25
8
7
11.5
6
5
54
4
{
2
{
3
{
1
Signal Input:
0 to 20mA, 4 to 20mA or 0 to 5mA
Signal Output:
0 to 20mA, 4 to 20mA or 0 to 5mA
Input Current:
Max. 30mA
Load:
Max. 600Ω
Voltage loss between input and output: Approx. 3.3V
Output Ripple:
Less than 0.5% (20mA at 250W)
Temp, Coefficient:
Less than ±100PPM/°C
Accuracy:
±0.1% (23°C±1°C) at 250W load
Additional Error:
+0.1%/100W at load,250W
-0.1%/100W at load.250W
Operating Temp:
-5 to +50°C, less than 90% RH
Mechanical Design:
Type of snap mount on DIN rail
More than 100MW at 500VDC between input
and output
1 min. at 2kVAC between input and output
Weight:
Approx. 80g
63
83
Side
41
TZ-41 is designed as "Self Powered Isolation" and transformation ratio is
1:1. Input current is 0 to 20mA, but customers can use input current
ranges 0 to 5mA, 0 to 20mA or 4 to 20mA.
Having 1:1 isolation the output current will of course be the same as the
input current, e.g., 0 to 5mA, 0 to 20mA, 4 to 20mA.
TZ-41 will provide 0 to 5V or 1 to 5V output.
34.5
25.5
■ INPUT/OUTPUT
■ Output load and Accuracy
2 4
1 3
Input
Transmitter
Example load 450Ω
Standard accuracy:
±0.1%
Additional error (+200W): ±0.1% - 0.2%=-0.1% to -0.3%
(-0.1%/100Ωatload>250Ω)
6 8
5 7
LOAD
Please note the TZ-41 can operate into a load of up to 600W. Accuracy
is a function of load resistance. Standard accuracy is +/- 0.1% with a
250W load and ambient temp. of 23±1°C. For loads other then 250W
accuracy changes as shown below.
Output
DC0~20mA(4~20mA)
■ Block Diagram
Chopper Oscillation Circuit
（＋）
3
Output
（−）
4
N.C
N.C
86
Rectifier
Circuit
５
（＋）
Output
６
（−）
2
７
1
８
N.C
N.C
TZ-5A
■ Features
•Isolated Input/Output/Power supply
•DIN rail mount
•Input RTD sensor
■ Dimension
PT-100 Ω three wires less than 20Ω
Y
7
5
25
4
3
6
2
1
0 to 100°C
0 to 200°C
0 to 300°C
0 to 400°C
0 to 500°C
0 to 600°C
Special (0~600°C)
(Span more than 100°C)
1
2
3
4
5
6
8
98
94
54
Temp. Range
Code No.
41
DC voltage or current
Temp. Range
Code No.
1~5V
4~20mA
0~10V
Special (Current 20mA)
(Voltage less than ±10V)
1
2
3
Y
Allowable Load: More than 2KΩ(At 1 to 5V)
Resistance
More than 4KΩ(At 0 to 10V)
Less than 550Ω(At 4 to 20mA)
Operating Temp.:
Power Supply:
Burn Out:
±0.25% F.S
±200ppm/˚C (Typ.)
Less than 80mS (0~90%) (Typ.)
Input/Output/Power supply AC2000V/1 min.
100MΩ at DC500V
-5~50˚C
DC24V±10% less than 55mA
Upper side
■ Ordering Code
TZ-5A-
Input Code
{
Input
B
2 4
6 8
1 3
5 7
DC
24V
Output
B
Pt100Ω
Transmitter
{
1. DC 1~5V
Output Code 2. DC 4~20mA
3. DC 0~10V
Y. Special
A
LOAD
Accuracy:
Temp. Coefficient:
Response Time:
■ Block Diagram
1. 0~100°C
2. 0~200°C
3. 0~300°C
4. 0~400°C
5. 0~500°C
6. 0~600°C
Y. Special
Constant Current Circuit
Input Circuit
Span Zero
RTD 4
Output
＋5
ー6
3
2
Isolated
Amplifier
Output Circuit
＋7
DC24V
1
N.C
ー8
Burn-out Circuit
Power Circuit
87
TZ-5B
■ Features
•Isolated Input/Output/Power Supply
•DIN Rail mount
•Input Potentiometer
■ Dimension
Potentiometer (100 to 10KΩ)
7
5
25
6
4
3
1~5V
4~20mA
0~10V
Special
1
2
3
Y
2
Temp.Range
Code No.
1
8
98
94
54
✽Special Current Output Range: Less than 20mA (Min. span 1mA)
✽Special Voltage Output Range: Less than ±10V (Min. span 1V)
41
Allowable Load: More than 2KΩ(At 1 to 5V)
Resistance
More than 4KΩ (At 0 to 10V)
Less than 550Ω (At 4 to 20mA)
±0.25%F.Sc
±200ppm/˚C (Typ.)
Less than 50mS (0~90%) (Typ.)
Input/Output/Power supply AC2000V/1 min.
100MΩ at DC500V
Operating Temp.:
-5~50˚C
Power Supply:
DC24V +15%,-5% less than 55mA
Zero Adjustment Range: 0~10%
Span Adjustment Range: 90~100%
Reference Voltage:
0.5V
Accuracy:
Temp. Coefficient:
Response Time:
Transmitter
TZ-5B-
Input
{
DC 1 to 5V
Output Code DC 4 to 20mA
DC 0 to 10V
Y. Special
2 4
6 8
1 3
5 7
DC
24V
LOAD
A
■ Ordering Guide
Output
B
Potentionmeter
■ Block Diagram
Constant Voltage Circuit
Output Circuit
Potentionmeter
4
Span Zero
3
2
Isolated
Amplifier
1
N.C
＋7
DC24V
ー8
Input Circuit
88
Output
＋5
ー6
Power Circuit
TZ-5C
■ Features
•Input K sensor
•Isolated input/output/power supply
•DIN rail mount
•Small size and easy installation
■ Dimension
Front
25
4
3
8
2
1
0 ~ 500°C
0 ~ 1000°C
Special
(0 ~ 1000°C)
Span
(300 ~ 1000°C)
1
2
Y
7
98
94
54
Temp. range
Code No.
6
Sensor type K
5
Side
41
Output
Code No.
DC 1~5V
DC 4~20mA
DC 0~10V
Special
(Current less than 20mA)
(Voltage less than ±10V)
1
2
3
Y
DIN RAIL
-
K Sensor
TCJ Senser
+
2 4
6 8
1 3
5 7
DC
24V
LOAD
±0.4% F.S
±300ppm/˚C F.S (TYP.)
Less than 0.5sec (0~90%) (TYP.)
DC1~5V more than 2kΩ
DC4~20mA Less than 550Ω
DC0~10V more than 4kΩ
Insulated resistance:
Input/output/power supply more than
100MΩ(DC500V)
Dielectric Stregth:
Input/output/power supply AC2000V/1min.
Power Supply:
DC24V+15%,
-5%
Power Consumption:
Less than 60mA
Operation Temp:
-5~50˚Cless than 90%RH
Cold Junction Compensator: ±1˚C at 20˚C±10˚C
Accuracy:
Temp. Coefficient:
Response Time:
Load Resistance:
OUTPUT
■ Ordering Guide
{
{
1. DC 1~5V
Output 2. DC 4~20mA
3. DC 0~10V
Y. Special
Input
Transmitter
TZ-5C-
■ Block Diagram
1. 0~500°C
2. 0~1000°C
Y. Special
Burn out Input Circuit
Span Zero
3
Output
＋5
ー6
+
Sensor
4
Input
ー
N.C 2
N.C
Isolation
AMP
Output Circuit
＋7
DC24V
1
ー8
Cold junction
Compensation
Circuit
89
TZ-5D
■ Features
• Input AC current(True-RMS)
• Isolated input/output/power supply
• DIN rail mount
• Small size and easy installation
25
8
7
98
94
54
Special
Special
AC current input: Less than 0~5A,Min span AC1A
DC current output: Less than DC20mA,Min span DC1mA
DC voltage output: Less than DC±10V,Min span DC1V
Side
DC 1~5V more than 2kΩ
DC 0~10V more than 4kΩ
DC 4~20mA less than 550Ω
41
Load resistance:
Front
6
DC 1~5V
DC 4~20mA
DC 0~10V
DC 1~5V
DC 4~20mA
DC 0~10V
5
Output
AC 0~1A
AC 0~1A
AC 0~1A
AC 0~5A
AC 0~5A
AC 0~5A
4
Intput
3
1
2
3
4
5
6
Y
2
Code No.
■ Dimension
1
■ Input /Output Specification
Operation Temp:
±0.1% F.S
40Hz~1kHz
±200ppm/˚C (Typ.)
Less than 0.5sec (0~90%)
DC24V+15% less than 55mA
-5%
-5~50˚C less than 90%RH
Input/output/power supply more than
100MΩ(DC500V)
Input/output/power supply AC1500V/1min.
■ Ordering Guide
Input
TZ-5D-
Transmitter
{
1. AC 0~1A
2. AC 0~1A
3. AC 0~1A
4. AC 0~5A
5. AC 0~5A
6. AC 0~5A
Y. Special
DIN RAIL
Output
2 4
6 8
1 3
5 7
DC
24V
INPUT
DC 1~5V
DC 4~20mA
DC 0~10V
DC 1~5V
DC 4~20mA
DC 0~10V
LOAD
Accuracy:
Input Frequency:
Temp. Coefficient:
Response Time:
Power Supply:
OUTPUT
■ Block Diagram
Zero Span
4
Input
3
C/T Isolation RMS Circuit
Output
＋5
ー6
Output Circuit
2
＋7
1
N.C
ー8
DC24V
90
TZ-5E
■ Features
•Input AC voltage
•Power supply DC24V
•DIN rail mount
•Small size easy installation
■ Dimension
Front
6
8
7
DC
24V
LOAD
4
3
98
94
54
2
AC 0~35V
AC 0~110V
AC 0~150V
Special
5
6
7
Y
1
Input
Code No.
5
25
Special specification
Voltage: less than AC300V, min span AC4V
1
2
3
Y
Output
Load resistance
DC 1~5V
DC 4~20mA
DC 0~10V
More then 2kΩ
More then 550Ω
More then 4kΩ
Side
41
Code No.
Special
Current: less than 20mA,min span 1mA
Voltage: less than ±10V,min span 1V
DIN RAIL
Accuracy:
Temp. coefficient:
Response time:
Input frequency:
Dielectric stregth:
Operating temp.:
Power supply:
±0.1% F.S
±200ppm/˚C F.S (Typ.)
70mS (Typ) 0~90%
40H~1KHz
Input/output/power supply AC2000V/l min.
Input/output/power supply more than 100MΩ
at DC500V
-5˚C~50˚C (less than 90% RH)
DC24V -5%, +10%
2 4
6 8
1 3
5 7
AC
■ Ordering Guide
TZ-5E-
{
{
OUTPUT
1. DC 1~5V
Output 2. DC 4~20mA
3. DC 0~10V
Y. Special
5. AC 0~35V
6. AC 0~110V
7. AC 0~150V
Y. Special
Transmitter
Input
■ Block Diagram
RMS
Conversion
4
Input
3
Isolation
Span Zero
AMP
Output
＋5
ー6
Output Circuit
2
＋7
1
N.C
ー8
DC24V
91
TZ-5F
■ Features
•Input small current and voltage
•Power supply DC24V
•DIN rail mount
•Small size and easy installation
■ Dimension
Front
8
6
4
98
94
54
3
DC 0~10mV
DC 0~50mV
DC 0~100µA
Special
1
2
3
Y
2
Input
Code No.
1
7
5
25
Current: less than 1mA, min span 10µA
Voltage: less than 100V, min span 5mV
Side
Output
Code No.
Current: less than 20mA, min span 1mA
Voltage: less than ±10V, min span 1V
41
DC 1~5V
DC 4~20mA
DC 0~10V
Special
1
2
3
Y
DIN RAIL
Load resistance:
Accuracy:
Temp. coefficient:
Response time:
Dielectric stregth:
Operating temp.:
Power supply:
■ Ordering Guide
TZ-5F-
More than 2KΩ( at 1~5V)
More than 4KΩ( at 0~10V)
Less than 550Ω( at 4~20mA)
±0.25% F.S
±200ppm/˚C F.S (Typ.)
Less than 0.1sec 0~90%
Input/output/power supply AC2000V/l min.
Input/output/power supply more than 100MΩ
at DC500V
-5˚C~50˚C (less than 90% RH)
DC24V -5%, +15%
{
{
INPUT
2 4
6 8
1 3
5 7
DC
24V
LOAD
OUTPUT
Transmitter
1. DC 1~5V
Output 2. DC 4~20mA
3. DC 0~10V
Y. Special
Input
1. DC 0~10mV
2. DC 0~ 50mV
3. DC 0~100μA
Y. Special
■ Block Diagram
Input Conversion
Span Zero
3
Input
4
1
Output
＋5
ー6
Isolation
AMP
Output Circuit
＋7
DC24V
2
N.C
ー8
92
DIGITAL PANEL METER
ACCESSORIES
Splash Proof Cover (WP)
Shunt Resistor (20A, 60A)
20A/200 mV±0.5%
60A/ 60 mV±0.5%
107
59
140
Height 50
Fittng hole distance 120mm
• Dimensions 59 mm(H) ｴ 170 mm(W) ｴ 18 mm(D)
• Dust-proof and water proof
• Available bracket installation 1/8 DIN case
Power Supply
IP66 COVER (WP-3)
3
+5V DV NC
45
2
AC100V GND
1
6
5
37
2- 4.1× 6φ
80
4
43
30
69±0.5
Model No.
Input voltage
APS-250-1
90~132VAC
APS-250-2
180~264VAC
APS-240-1
90~132VAC
APS-240-2
180~264VAC
Output voltage
Output current
4.85~5.15V
Max 250mA
24V±10%
80mA
(Input voltage is selectable internal switch)
93
DIGITAL PANEL METER
ACCESSORIES
■ VOLTAGE DIVIDER
･FOR USE 0.2V RANGE(11 Range)
MODEL
RANGE
DIVIDE RATIO
ADV-501-12
ADV-501-13
ADV-501-14
ADV-501-15
±
2V
± 20V
± 200V
±2000V
1/10
1/100
1/1000
1/10000
INTERNAL
RESISTANCE
1MΩ
10MΩ
10MΩ
100MΩ
RESOLUTION
1mV
10mV
100mV
1V
MAX. INPUT
VOLTAGE
less than ± 200V
± 750V
± 750V
±2500V
ACCURACY
less than 0.1%
0.1%
0.1%
0.1%
TEMPERATURE
COEFFICIENT
± 50PPM
± 50PPM
± 50PPM
±100PPM
･FOR USE 2V RANGE(12 Range)
MODEL
RANGE
ASH-400-19
ASH-400-20
ASH-400-21
ASH-400-22
ASH-400-23
ASH-400-24
ASH-400-25
ASH-400-26
±1.999µA
±19.99µA
±199.9µA
±1.999mA
±19.99mA
±199.9mA
±1.999A
±5.00A
INTERNAL
RESISTANCE
100kΩ
10kΩ
1kΩ
100Ω
10Ω
1Ω
0.1Ω
0.01Ω
RESOLUTION
1nA
10nA
100nA
1µA
10µA
100µA
1mA
10mA
INPUT MAX.
CURRENT
less than±1mA
± 5mA
± 10mA
± 50mA
±150mA
±500mA
±3A
±8A
ACCURACY
± 1%±1digit
±0.5%±1digit
±0.2%±1digit
±0.2%±1digit
±0.2%±1digit
±0.3%±1digit
±0.3%±1digit
±1%±1digit
■ SHUNT
･FOR USE 0.2V(11 Range)
MODEL
RANGE
DIVIDE RATIO
ADV-502-14
ADV-502-15
± 200V
±2000V
1/100
1/1000
■ DIMENSIONS
94
INTERNAL
RESISTANCE
10MΩ
100MΩ
RESOLUTION
100mV
1V
MAX. INPUT
VOLTAGE
less than ± 750V
±2500V
ACCURACY
less than 0.1%
0.1%
■ CONNECTION DIAGRAM
TEMPERATURE
COEFFICIENT
± 50PPM
± 100PPM
MEMO
95
MEMO
96
DIGITAL PANEL METER, TRASMITTER CATALOGUE 2004
We reserve the right to change specifications without notice.
33-6, YAGUCHI 2-CHOME, OHTA-KU,
TOKYO 146-8505, JAPAN
FAX
:(03)3757-2989
PHONE :(03)3579-3893
E-mail :[email protected]
June 2004(KS)

asahi keiki co.,ltd.

Transcription

Similar documents

f - Eurotronix, SA

asahi keiki co.,ltd.

electronic dc input meter tlc-110/ tlc-110l

Clamps, safety clamps and ferrules

LR2065 - Motwane