Mounting Systems

Transcription

Mounting Systems

Mounting Systems
2016 | 2017
M O U N T I N G S O LU T I O N S : T I L E R O O F T R A P E Z O I D A L M E TA L C O R R U G AT E D S A N D W I C H R O O F S E A M E D M E TA L F L AT R O O F I N S E R T I O N S YS T E M FA C A D E
Electricity and the sun – for us, these two elements are closely linked.
This is because photovoltaic technology provides us with a method of generating electricity
whose future potential is unbound. This is why, for the last 25 years, we have placed our bets
and gone all-in with the sun.
CONTENT
Introduction
08
08
10
13
14
16
A revolution in energy supply
Photovoltaics – The smart solution for energy security
novotegra – the perfect solution for every roof
Certifications and approvals
Mounting system layout with Solar-Planit
Skill, expertise and years of experience
1
Sloping roof
20
28
34
42
Mounting solutions for tile roof
Mounting solutions for trapezoidal panel roofs
Mounting solutions for corrugated and sandwich roof
Mounting solutions for seamed metal roof
Flat roof
49 Mounting solutions for flat roofs
In-roof | Facade
56 In-roof system
57 Facade system
Individual products
59
68
73
76
82
85
91
92
2
3
4
5
Annex
97 Terms of Guarantee
98 Contact
99 Remain Flexible with a Strong Network
Roof fixation
Rails
Module protection and rail top cover
Rail connector and expansion joint
Module bracket
Elevation
Facade
novotegra components
6
INTRODUCTION
r.e.sponsible
for your success.
Reliability, flexibility, partnership: That is our mission. With our products and services, we are
dedicated to adding value for our customers, partners and service providers, and helping them
succeed. We also take long-term responsibility for the environment and sustainable energy
supply, and practice this sustainability both internally and externally. Right from the start, our aim
has always been to make solar energy marketable and to actively contribute to the coming
energy transition. That is what makes us your responsible partner in the photovoltaic market.
Today and in the future.
W E TA K E R E S P O N S I B I L I T Y
For the satisfaction of our customers
Our customers know that we always give our best. In 2016,
this was again confirmed in writing: for the fifth time in a row,
we have been awarded the prestigious “Top PV Provider”
seal of quality from the Bonn-based market research institute
EuPD Research. The “TOP PV Supplier” quality seal illustrates
that we have been given the highest possible marks from the
leading installers in the industry.
But we have not stopped there. Because quality and good
service are so important to us, we have also been certified in
these areas by both TÜV South and ISO 9001. This gives us a
head start that pays out for our customers.
4
For fair and sustainable production conditions
We take great care when selecting our suppliers, paying
particular attention to the use of durable, high-quality and
resource-saving materials in production, as well as fairly
traded products.
We support the local economy and minimise long transport distances. Almost all of the components in our novotegra
installation systems are produced in Germany and other
EU countries.
BayWa r.e. was one of the first companies to be awarded
the "Pioneers of the Energy Transition" certificate by TÜV SÜD
in 2014. This certification is further proof of our dedication to
the energy transition in all parts of our business.
"We are committed to the
success of our customers. This
is why BayWa r.e. is regularly
awarded top marks."
Günter Haug,
Managing Director BayWa r.e. renewable energy GmbH
For the best products
We demand a lot from our products. Our technicians
look for the best solution to every need, paying close
attention to the feedback from our customers. This
helps us constantly improve our components, and
therefore increase yield.
Cooperating with leading specialists in the solar sector
helps us constantly expand our expertise, and inspires us
to refine our photovoltaic technology.
Errors and changes reserved.
For equal opportunities
For years, the individual components of our novotegra
installation systems have been preassembled in cooperation with social workshops in Baden-Württemberg. These
institutions offer people with disabilities and mental
illnesses the chance to participate in working life and
develop as people.
Approved by the Chamber of Industry and Commerce,
we are constantly training young people and increasing
their chances in the job market.
5
1
Introduction
INTRODUCTION
1
A revolution in
energy supply
Driving photovoltaic technology forward and exploiting its inexhaustible
potential for decentralised energy supply is one of the most important
tasks for the future. Given the increasing scarcity of resources however,
we also need a balanced mix of renewable energies today to secure energy
supply, such as photovoltaic, wind, biomass and geothermal energy. The
great global challenge is to use and integrate these renewable energies
to secure energy supply for the 21st century. BayWa AG recognised this
early, and founded the BayWa r.e. renewable energy GmbH in 2009. This
subsidiary covers all our activities in renewable energy, including solar
energy, wind energy, bio-energy and geothermal energy. Since its foundation, BayWa r.e. renewable energy has developed into one of the leading
traders and project developers in Germany and Europe. Our aim is to help
renewable energies grow around the world.
Solar energy
Wind power
Bio-energy
Geothermal
energy
Business units of
BayWa r.e. renewable energy GmbH
BIG AIMS NEED SMART SOLUTIONS
Our trading company, BayWa r.e. Solar Energy Systems GmbH, is one
of the largest suppliers of photovoltaic systems in Germany, with over
25 years of experience and a deep knowledge of photovoltaic technology.
We help our customers find solutions for system planning, financing and
implementation, and offer a range of services for system operation.
We are also active in photovoltaic wholesale, with independent commercial subsidiaries worldwide. In Great Britain, specialist tradesmen are
advised and supplied with photovoltaic components by BayWa r.e. Solar
Systems Ltd. We are also active on the Italian wholesale market with our
subsidiary Tecno Spot GmbH (based in Bruneck in South Tyrol). Customers in Scandinavia are served by Danish company BayWa r.e. solar systemer ApS. BayWa r.e. Solar Systems S.á r.l. supports customers in France and
the Benelux countries, while the long-standing Solarmarkt GmbH supports
us in the Swiss market. This gives us an expert alliance of wholesale companies in almost every important photovoltaic market in Europe.
Our size, our global network of sales subsidiaries, and the financial
strength of BayWa AG, combined with the expertise of the BayWa r.e.
business units, means that we are well equipped to drive forward global
expansion of renewable energy.
With the power of a large brand, we can help you be successful in the
photovoltaic market both today and in the future.
Svendborg
Denmark
BAYWA R.E. SOLAR SYSTEMER APS
Machynlleth
Wales/UK
BAYWA R.E. SOLAR SYSTEMS LTD.
Wemperhardt
Luxembourg
BAYWA R.E.
SOLAR SYSTEMS S.À R.L.
Aarau
Switzerland
SOLARMARKT GMBH
Tübingen
Germany
BAYWA R.E. SOLAR ENERGY
SYSTEMS GMBH
Bruneck
Italy
TECHNOSPOT SRL
BayWa r.e.commercial subsidiaries in Europe
Photovoltaics – The smart solution
for energy security
YO U R PA R T N E R F O R P H O T O V O LTA I C S
We have actively supported the development of solar energy in Germany
for 25 years. We see ourselves here not only as a wholesaler, but also as a
partner to the trade. Working in close personal cooperation, we add our
experience to every photovoltaic project, helping to guarantee the best
possible results and high profitability. A wide range of consultation and
planning services is just as important to us as active with on-site support
for initial assembly.
Santa Fe, USA
BAYWA R.E. SOLAR SYSTEMS LLC
Singapore, Singapore
BAYWA R.E. SOLAR PTE LTD.
BayWa r.e. commercial subsidiaries
in the US and Singapore
8
1
Our novotegra mounting systems are made from durable and corrosionresistant aluminium and stainless steel. Taking the Eurocode load standards into account, they are extremely sturdy and strong, even at high snow
and wind loads. Our mounting systems are certified to do justice to this
quality. With CE marking, Certipedia from TÜV Rheinland and building
regulations approval, you can can be rest assured of the quality of our
mounting solutions!
PROFESSIONAL PLANNING
BayWa r.e. experts in consultation and planning
Are you looking for a mounting system for a flat roof with low load-bearing
capacity? Then plan your system together with the experts. We can select
the ideal components for your specific requirements, ensure the right
sizing and shade-free placement, and match all components precisely.
We would be happy to help you in planning and support you with our expert knowledge.
RELIABLE LOGISTIC S
First and foremost, we prioritise advice, quality and service. To make sure
we can supply you with all the items you need from the following catalogue
reliably and on time, we have invested in an efficient storage and logistics
centre. With over 10,000 square metres of warehouse space, it allows us
to constantly keep all components in stock. Short delivery times and reliable
delivery directly to your site give you the best possible planning security.
Over 10,000 square metres of warehouse space
WIDE-R ANGING SERVICE
Our headquarters in Tübingen and sales offices in Munich, Nuremberg,
Duisburg and Brunswick help us be close to our customers. Each office
also has a full sales team with photovoltaic specialists who can answer
your questions on planning, components and installation systems.
O U T S TA N D I N G P E R F O R M A N C E
SALES OFFICE
BRUNSWICK
SALES OFFICE
DUISBURG
SALES OFFICE
NUREMBERG
BAYWA R.E.
SOLAR ENERGY
SYSTEMS GMBH
TÜBINGEN
GERMANY
B AY WA R . E . PA R T N E R S A L E S
SALES OFFICE
MUNICH
BayWa r.e. Solar Energy Systems GmbH
sales offices in Germany
For the fifth time in a row, we received the "TOP PV Supplier" seal of quality
from the market research institute EuPD Research in Bonn. This independent
award reflects the opinion of qualified installation technicians towards PV
wholesalers in Germany, and is yet more proof of the outstanding service
and continually high quality standard that we offer our customers. Quality
and good service are so important to us, we had this confirmed by TÜV
SÜD and are certified to ISO 9001. This is an advantage that pays off for
our customers.
In our partner sales business, we cooperate with sales partners who are
close to potential end customers. Together, we develop custom business
models which help us inform customers about photovoltaic technology, as
well as provide tailored and attractive offers. All with the aim of raising
even more interest in photovoltaic technology. How do you benefit? We
only use selected specialist installation technicians and solar installers
from our network to fit the photovoltaic system on site.
9
INTRODUCTION
P R O V E N Q UA L I T Y
I N T E R L O C K I N G T I L E S | B E AV E R TA I L T I L E S | S A N D W I C H | C O R R U G AT E D
novotegra – the perfect solution
for every roof
NOVOTEGR A FOR
INTERLOCKING TILED ROOFS
NOVOTEGR A FOR
B E AV E R TA I L T I L E D R O O F S
NOVOTEGR A FOR
SANDWICH ROOFS
NOVOTEGR A FOR
C O R R U G AT E D R O O F S
10
1
T R A P E ZO I DA L M E TA L | S E A M E D M E TA L | F L AT R O O F
INTRODUCTION
novotegra – the perfect solution
for every roof
N O V O T E G R A F O R F L AT R O O F
E A S T- W E S T S Y S T E M
NOVOTEGR A FOR
S E A M E D M E TA L R O O F S
NOVOTEGR A FOR
T R A P E ZO I DA L M E TA L R O O F S
N O V O T E G R A F O R F L AT R O O F
S O U T H - FAC I N G S Y S T E M S
11
I N - R O O F | FAC A D E
The perfect solution
for every roof
IN-ROOF SYSTEM
FAC A D E S Y S T E M
IN-ROOF SYSTEM
FAC A D E S Y S T E M
12
1
The new novotegra combines the best of two brands: the proven clamping
system by novotegra and the sturdy insertion system by Creotecc. We demand a lot from our photovoltaic mounting systems: They have to securely
hold the solar modules, be made from durable, weather-resistant materials, and sometimes need to withstand very heavy loads. That is why we
make our mounting systems from durable and corrosion-resistant aluminium and stainless steel. Taking the Eurocode load norms into account, they
are extremely sturdy and resilient, even at high snow and wind loads. We
use high quality materials and reliable production methods. With our certifications and approvals, we can also ensure that this quality will stay high
for years to come.
T Ü V R H E I N L A N D C E R T I F I C AT I O N
We have had the quality and reliability of our mounting system certified,
and have received the test mark from TÜV Rheinland, one of Germany's
leading technical certification bodies.
The certification's test catalogue covers all legal and technical details
that the mounting systems have to fulfil. This ensures that all our photovoltaic mounting systems are manufactured in exactly the same way as the
tested systems – using the same quality materials and processes. We also
passed the audit in the area of "sales and consulting".
CE MARK
We use our own production inspection for the novotegra mounting system,
which meets all the specified requirements of EN 1090-1:2009+A1:2011,
annex ZA as basis for the CE mark as part of EU Regulation No. 305/2011
(Construction Products Regulation – CPR). Execution in line with EN
1090-2 or EN 1090-3, EXC1.
G E N E R A L B U I L D I N G I N S P E C T O R AT E A P P R O VA L S
You can have confidence in the structural analyses of relevant system
components as these have been independently checked. In cooperation
with an independent auditor, we have prepared the required approvals and
have received the following general building inspectorate approvals from
the German Institute for Construction (DIBt):
Z-14.4-716: Connections for PV installation systems
Z-14.4-723: Rail connectors and base profile
Z-14.4-735: Module fasteners, module supports, cross rail connectors
Z-14.4-741: Roof hooks, hanger bolts and fastenings on rail bases
S T R U C T U R A L A N A LY S I S W I T H S O L A R - P L A N I T
Our configuration tool Solar-Planit gives you the structural analysis of our
mounting system free at the press of a button! The load determination for
the structural analysis of the substructure is based on the specifications of
Eurocode 1, taking into account the national specifications of the countries
that can be selected in the software. The only exception is Switzerland, for
which the load is calculated according to the specifications of SIA 261
(2003).
S Y S T E M T E S T I N G W I T H K I N G S PA N S A N D W I C H E L E M E N T S
We have gained approval from Kingspan GmbH for roof elements of the
type Kingspan 1000 RW (IPN)/ FF (MiWo), which allows us to directly attach our mounting system on these sandwich roofs. The solutions, whether
attached directly or laterally on the raised bead, are described in the chapter on trapezoidal metal roofs.
13
INTRODUCTION
Certifications and approvals
ROOF COVERING
ROOF
Mounting system layout with
Solar-Planit
2. Fill out the data on roof covering
4. Select site data
P R O J E C T DATA
3. Indicate the roof construction data
Entering data is quick, clear and easy!
INDIVIDUELLE PLANUNG
ROOF CONSTRUCTION
S I T E DATA
1. Enter roof dimensions
Solar-Planit – A result is just a few clicks away
• Define location and roof features individually for your project
• Select module and installation system design – from tile roof to flat roof
• Plan module loading – easy to plan chimneys, roof windows and dormers
• Perform structural analysis and optimise the system – in line with Eurocode standard for many European countries
• Result – complete overview of structural analysis, material requirements and costs
• System project reports – documentation for you and your customers at the push of a button
14
1
INTRODUCTION
MODULE PLANNING
MOUNTING SYSTEM
Mounting system layout with
Solar-Planit
6. Place obstructions and modules
R E S U LT S
3D VIEW
5. Determine module and design
8. Material parts list with cost and static information
D O C U M E N TAT I O N
7. Optional 3D output
Clear project report at the push of a button
Your benefits
• Free system planning, simply register at www.solar-planit.de and get started
• Monthly webinars from our novotegra experts and free participation in our seminars
• Take full control of your planning – you determine the when, where and how for all our mounting systems solutions
• The online solution enables quick decision-making in project approval, whether in your team or in our sales division
• Clear and customised documentation
• Security for your project – planning in line with Eurocode regulations
15
Skill, expertise and years of experience
Take advantage of our experience and expertise. We have been successful
in the market with our photovoltaic mounting systems for years, and have
now gone global. From development and initial prototypes to series production, every component in our photovoltaic mounting system is made by
us. We put all our components through their paces on our test bench with
calibrated measurement instruments. Our international experience in
sales and operation, in Europe and around the world, flows back into our
development. This means that our mounting system takes country-specific
features into account.
We are passionate about providing expert support to our customers.
That is why our experienced engineers developed our online configuration
tool Solar-Planit, specially designed for our mounting system. It allows you
to plan simply, quickly and in full compliance, whilst also enabling structural
analysis according to Eurocode. Our technicians can also help you in person,
and give you advice on special solutions for your individual photovoltaic
project.
Get reliable advice for special solutions from
our novotegra experts
C L E A R LY E X P L A I N E D : O U R S E M I N A R S A N D A D V E R T I S I N G
M AT E R I A L
We offer mounting system seminars for all our customers in Europe, both
in our national sales subsidiaries and in Germany at the headquarters of
BayWa r.e. Solar Energy Systems in Tübingen, near Stuttgart. You can also
find free, monthly webinars in English and German for our Solar-Planit
configuration tool, with helpful assembly videos also available at www.youtube.com/user/novotegra.
We would also be happy to provide you with advertising material with
which you can clearly explain the benefits of our photovoltaic mounting
system to your customers. Alongside our catalogue, brochures, data sheets
and the comprehensive information found on our website, you can also
loan a wide range of advertising material for exhibitions or customer visits
– from models and presenters to show trailers. We also offer small mounting system models for loan and purchase. If you want to know more about
our advertising material, we will be happy to help you in person.
Advertising material support
A H E L P I N G H A N D : O N -S I T E S U P P O R T F O R I N I T I A L
A S S E M B LY
Are you fitting our photovoltaic mounting system for the first time? Then
you could benefit from our free initial assembly support. You can get an indepth knowledge of our mounting system in the field. One of our technical
advisers will visit you on site for a whole day, where they will train you, help
with mounting, and offer support in all matters relating to the mounting
system. They will also discuss the results of the structural analysis made
using our own configuration tool Solar-Planit. Furthermore, you can also
receive background information on how our components are designed and
developed, along with helpful tips on our photovoltaic mounting system.
Initial assembly service
16
INTRODUCTION
1
More kilowatts per roof surface
with the novotegra flat roof system
with east-west elevation
17
Sloping roof
SLOPING ROOF
2
2
Main applications
Clamping system: Vertical installation with single rail
Clamping system: Horizontal installation with 2 rails
on beavertail tiles
Insertion system: Vertical installation
Insertion system: Horizontal installation
Your benefits
• Proven, secure, stable
• Suitable for every tile type
• Durable and corrosion-resistant materials
• 10 year product guarantee
20
Further applications
Clamping system: Vertical installation with single rail
Clamping system: Horizontal installation with single rail
on beavertail tiles
TILE ROOF
2
Clamping system: Vertical installation with two rails
21
Tile roof | Clamping system
Clamping system in a vertical installation with single rail
T H E P E R F ECT S O LU T I O N FO R E V E RY T I L E R O O F
A DVA N TAG E S
From pan tiles to beavertail roofing, from a simple saddle roof or more demanding roof designs, we have the right photovoltaic mounting system for
tile roofs. Quick and simple to assemble, it offers a range of individual
solution options and is extremely sturdy and resilient – even under high
snow and wind loads. The tried-and-tested clamping system offers you an
extremely reliable assembly technology, which can be used to secure the
modules both vertically and horizontally.
Our mounting system is made from durable and corrosion-resistant
materials. Preassembled components reduce the installation workload.
You can install a wide variety of modules in the clamping system using
just a handful of module clamp types, available in bare aluminium or black.
Our sturdy roof hooks are available for a range of load requirements and
tile shapes, either solid cast or with three adjustment settings. They can all
be easily attached without the need for broken tiles or expensive sheet
tiles, and do not make contact with the tile even under pressure.
The module system rails are available in a range of spans, both with
and without an integrated cable duct for cables and connectors. All of our
rails can be extended using pluggable or external connectors, with rail
protrusions also possible. End clamps can be used to connect modules
and system rails virtually flush. Whatever rails you use, the substructure
remains virtually invisible. This creates uniform, attractive module arrays.
You can also use our configuration tool Solar-Planit. Quick and simple
to use, it helps you perform a compliant system layout and structural analysis.
It also takes load assumptions for different countries into account according to Eurocode. Our mounting system also ensures excellent rear ventilation of the modules, creating an important condition for improving the
yield of the photovoltaic system.
22
• High production quality and durability
• Sturdy roof hooks for every requirement,
either solid cast or with triple adjustment
• Excellent rear ventilation
• Pre-assembled components
• Simple, Eurocode-compliant layout
with our Solar-Planit online tool
CLAMPING SYSTEM
Middle clamp or End clamp
Page 83
Page 82
TOP-FIX
SIDE-FIX
Connector
P
Page 79
Page 77
Rail
Page 70
Page 70
End Cap
Page 75
Page 73
Roof hook
Page 61
Page 60
Screws
Page 67
Page 67
23
TILE ROOF
2
Tile roof | Insertion system
Insertion system in the vertical installation model
T H E I N S E RT I O N SYST E M : R O B U ST, S EC U R E , AT T R ACT I V E
A DVA N TAG E S
Are you looking for a photovoltaic mounting system for a tile roof? Our
insertion system for tile roofs not only gives you top-quality stability and
safety, but also the advantages of a tension-free, floating module layout.
It also ensures an attractive look for your photovoltaic system.
The insertion system is extremely resilient, providing a sturdy and
protective hold for the modules. As they are laid in the rails, the load is distributed across the entire length of the module frame. The insertion system
makes horizontal and vertical assembly of the modules extremely quick
and easy, whilst ensuring excellent rear ventilation. It is suitable for all
framed and some frameless modules. The insertion rail can be fitted with
a snow guard if required.
Our mounting system gives you maximum flexibility. Whatever tiles are
used on the roof, and whatever its shape, we have the perfect insertion
system for every individual customer requirement. Our roof hooks are
available for all kinds of load requirements. They are simple to fit, without
the need for broken tiles or expensive sheet tiles. You can choose between
solid-cast roof hooks, or roof hooks with three adjustment settings that let
you easily compensate for unevenness. The construction is securely
mounted in the cross rail configuration, with rails available both with and
without integrated cable duct. You can also use our online configuration
tool Solar-Planit for quick, simple and fully compliant planning, as well as
for structural analysis according to Eurocode.
The insertion rails are available in bare aluminium and black. Together with
the other discreet components of the mounting system, this lets you create
attractive and uniform module arrays. A standard construction of blackanodised insertion rails and dark modules turns every roof into a designer
object.
24
• Attractive appearance
• Tension-free and floating module layout
• Sturdy roof hooks for every
requirement, either solid cast or
with triple adjustment
• Pre-assembled components
• Durable and corrosion-resistant
materials
INSERTION SYSTEM
Page 68
Connector
Page 78
Edge stop
Page 74
2
TILE ROOF
Insertion Rail
SIDE-FIX
TOP-FIX
Retaining clip
Page 76
Page 76
Connector
Page 79
Page 77
Rail
Page 70
Page 70
End Cap
Page 75
Page 73
Roof hook
Page 61
Page 60
Screws
Page 67
Page 67
25
Secure and stable – novotegra
for tile roofs
26
System matrix mounting systems tile roof
The adjacent table lists possible combinations of mounting profiles and roof fixation. These apply to systems in both the clamp
version (p. 22) and insertion version (p. 24).
INSTALLATION
PROFILE
ARTICLE NUMBER
DESIGNATION
251141
ALUVER
STANDARD
251142
ALUVER
PREMIUM
215115FF
C-RAIL
47/71/95
CATALOGUE
PAGE
252786
Pan tile hook 633
ALU vertical flex3
61
251020
Cast aluminium roof
hook, S-shaped
vertical
61
251021
Cast aluminium roof
hook, S-shaped
horizontal
62
251024
Roof hook 533
with M8 slot bolt
61
251025
Roof hook 544
with M8 slot bolt
62
210020|210025
Roof hook
Flex 30|40 M10
60
210021|210026
Double Roof hook
set
Flex 30|40 M10
60
210042|210044
Roof hook
ZD 30|40 M12
60
210043|210045
Double Roof
hook set
ZD 30|40 M12
61
214062
Roof hook set
BS 30 M12
60
214063
Double Roof
hook set
BS 30 M12
61
CATALOGUE PAGE
251140
ALUVER ECO
70
70
70
2
TILE ROOF
ROOF
FIXATION
70
27
Mounting solutions for
trapezoidal panel roofs
Main applications
Clamping system: Vertical installation
with direct attachment short rail
Clamping system: Horizontal installation
with direct attachment
Insertion system: Vertical installation with direct attachment
Insertion system: Horizontal installation on short rail
Clamping system: Vertical installation elevated
Your benefits
• Quick and easy installation
• Simple system design and Eurocode-compliant
structural analysis with our online tool Solar-Planit
28
trapezoidal panel roofs
Clamping system: Vertical installation
with direct attachment rail section
Elevation: South facing with direct attachment
on east-west roof
TR APEZODIAL
2
Elevation: South facing with direct attachment
Elevation: South facing with insertion rail on east-west roof
Elevation: South facing with insertion rail on bridge
29
Trapezoidal roof | Clamping system
Clamping system version horizontal installation with direct attachment
S M A RT D E S I G N , S EC U R E , STA B L E A N D D U R A B L E
A DVA N TAG E S
Do you want to mount a proven photovoltaic mounting system on a trapezoidal metal roof? Are you looking for high production quality, durable and
corrosion-resistant materials, stability and reliability? Our clamping system
for trapezoidal metal roofs can offer you all these advantages, along with
an attractive cost effectiveness.
The mounting system is attached directly to the trapezoidal panel.
With our many years of experience, we have refined our mounting system
to the tiniest detail – for the safety of your system, high layout flexibility
and simple, quick assembly. The clamping system helps you secure the
modules in both vertical and horizontal format using module clamps. Our
mounting system can fit all module frame heights on the trapezoidal roof
with just a handful of clamped types, which are available in bare aluminium
and black. They are mounted on our short, practical and fully preassembled rails. Pre-sawn and with attached backing and sealing strips made
from high-quality EPDM, the short profiles are easy to handle on site and
on the roof. The rails are always mounted from above using approved thin
sheet screws. These are screwed into the trapezoidal panel without generating metal chips, which can lead to corrosion if left laying around. They
also have the same head as the screws used on the module clamps, meaning you only need one tool.
• Low installation workload thanks to
pre-assembled components
• Quick and easy installation
• Just a handful of individual components
• Direct attachment to the trapezoidal
panel
• Can be used from a steel panel
thickness of 0.4 mm
• Simple system design and Eurcodecompliant structural analysis with our
online tool Solar-Planit
Our clamping system for trapezoidal metal roofs ensures good rear ventilation of the modules and an attractive look for your photovoltaic system.
They can be used from a steel panel thickness of 0.4 mm. Thanks to their
smart design, the screw connection creates an electrically conductive connection between the mounting system and the roof surface.
* Note: novotegra has system approval for Kinspan type 1000 RW (IPN)/
FF (MiWo) sandwich panels.
30
CLAMPING SYSTEM
Page 82
MODULE VERTICAL
MODULE HORIZONTAL
Rail
Page 69
Page 69
Roof fixation
Page 66
Page 66
31
TR APEZODIAL
2
Trapezoidal roof | Insertion system
Insertion system for vertical installation with direct attachment
O U TSTA N D I N G Q UA L I T Y FO R YO U R T R A P E ZO I DA L
M ETA L R O O F
With our insertion mounting system, you can attach photovoltaic modules
tension free and floating, while still ensuring they remain secure and stable
on your trapezoidal metal roof. The modules are gently laid with the entire
frame length in our insertion rails, which are available in bare aluminium
and black. Depending on the combination of rail and module, you can use
the insertion mounting system to create an attractive and uniform system
surface. The insertion mounting system also features a smart design and
quick and simple assembly, with high production quality and durable, corrosion-resistant components and can also be expanded with a snow guard.
A DVA N TAG E S
materials
• Direct attachment to the trapezoidal
panel
• Just a handful of individual components
• Quick installation thanks to simple
module insertion
• Tension-free and floating module layout
The insertion rail is attached directly on the roof, using a retaining bracket
connected on the side of the raised bead. Our insertion mounting system
for trapezoidal metal roofs can be used from a steel panel thickness of
0.4 mm. It offers excellent rear ventilation for the modules, which can be
mounted both vertically and horizontally. The non-chip thin sheet screws
we use on trapezoidal metal roofs are approved by construction authorities, and are screwed into the trapezoidal sheet without leaving behind
potentially corrosive metal chips. Another practical benefit is that the insertion mounting system for trapezoidal metal roofs consists of only a handful
of individual components, making it easier to install on the roof.
• Can be used from a steel panel
thickness of 0.4 mm
• Simple system design and Eurcodecompliant structural analysis with our
online tool Solar-Planit
Together with our free online tool Solar-Planit, developed specially by
our engineers for our mounting system, you can configure the system
and perform the structural analysis quickly, easily and in full compliance.
Solar-Planit also takes into account the load assumptions for different
countries according to Eurocode.
* Note: novotegra has system approval for Kinspan type 1000 RW (IPN)/
FF (MiWo) sandwich panels.
32
INSERTION SYSTEM
Insertion Rail
Page 68
Connector
Page 78
Edge stop
Page 74
FIXATION SYSTEM
EPDM sealing
Page 92
Roof fixation
Page 65
33
TR APEZODIAL
2
Mounting solutions for corrugated
and sandwich roof
Main applications
Clamping system: Horizontal installation with single rail
Clamping system: Vertical installation with two rails
Insertion system: Horizontal installation with bridge
Your benefits
• Low installation workload
• Good rear ventilation
of the modules
• Top quality: proven, secure, stable
34
Mounting solutions for corrugated
and sandwich roof
Elevation: South facing with two rails
C O R R U G AT E D | S A N D W I C H
2
Elevation: South facing with insertion system
on east-west roof
Elevation: South facing with clamping system
35
Corrugated and sandwich roof | clamping system
Clamping system for horizontal installation with single rail
S EC U R E A N D STA B L E , W I T H P R OV E N F L E X I B I L I T Y
A DVA N TAG E S
Photovoltaic mounting systems are mounted on sandwich and corrugated
roofs using hanger bolts. The hanger bolts offer high degree of flexibility,
and are available in a range of diameters for all kinds of installation
heights, insulation thicknesses and purlin intervals, as well as for purlins
made from steel and wood. The rails can be mounted directly with centric
load distribution, or with a simple side-mounted click mechanism. Together
with the reliable module clamps, this is a secure and stable mounting system for photovoltaic systems that has proven itself on sandwich and corrugated roofs for many years.
Our mounting system can help you achieve the perfect system design
for every individual requirement of your sandwich or corrugated roof. The
modules can be mounted both horizontally and vertically using the clamps,
whilst the substructure can be mounted both in a single layer or in a cross
rail configuration. The rails are available for a range of spans, with and
without integrated cable duct. They can be extended with pluggable or
external connectors, with protrusions also possible.
The module clamps let you connect the modules to the frame quickly,
simply and securely. Our mounting system lets you secure all modules with
just a few different clamp types, available in bare aluminium and black. End
clamps enable flush assembly of rails and modules. The discrete mounting
system components and uniform module arrays help create an attractive
look.
Our mounting system offers excellent production quality, with components made from durable and corrosion-resistant materials. You can use
our free online tool Solar-Planit, developed by our engineers to help you
configure your system and perform structural analysis to Eurocode standard. It lets you plan your system quickly, simply and in full compliance.
36
• Top quality: proven, secure, stable
• Highly flexible hanger bolts
• Good rear ventilation of the modules
• Also suitable for trapezoidal roofs
• For wooden and steel purlins
CLAMPING SYSTEM
Page 83
Page 82
SIDE-FIX
TOP-FIX
Connector
Page 79
Page 77
Rail
Page 70
Page 70
End Cap
Page 75
Page 73
Hanger bolt and
sealing
Page 62
Page 63
37
2
Corrugated and sandwich roof | Insertion system
Insertion system in the vertical installation model
I D E A L FO R CO R R U G AT E D A N D SA N DW I C H R O O FS
A DVA N TAG E S
With years of proven quality and well thought out to the tiniest detail, our
insertion mounting system lets you fit photovoltaic systems securely and
stably on any corrugated and sandwich roof. The modules are fitted floating and free of tension in the insertion rails, which are available in bare aluminium and black and protect the modules. They make it possible to install
modules quickly in both vertical and horizontal format. If required, the insertion rails can also be fitted with a snow guard to provide extra protection against snow falling off roofs.
• Quick installation thanks to simple
module insertion
• Low installation workload
• Also suitable for trapezoidal roofs
• Attractive appearance
We use standard hanger bolts to secure the rails to the corrugated or
sandwich roof. These bolts are available either preassembled or as individual parts depending on your requirements. Our hanger bolts variants for
steel and wooden purlins enable installation on all kinds of roofs with a
variety of installation heights or purlin intervals. They also distribute the
load safely and stably across the load-bearing structure. The lower system
rails of the cross rail configuration are available with or without an integrated
cable duct. Depending on the system rail, you can decide whether to clip
in the cable duct centrally or on the side.
Our insertion mounting system for corrugated and sandwich roofs is extremely resilient, even under high snow and wind loads. It ensures good
rear ventilation of your photovoltaic system. All components are made
from durable, corrosion-free materials. Our Solar-Planit software lets you
design the system and perform structural analysis quickly, easily and in full
compliance. Solar-Planit can also be used for international sites, as it uses
the individual suction and pressure loads at the site you have chosen to
calculate the photovoltaic system.
38
INSERTION SYSTEM
Page 68
Connector
Page 78
Edge stop
Page 74
SIDE-FIX
TOP-FIX
Retaining clip
Page 76
Page 76
Connector
Page 79
Page 77
Rail
Page 70
Page 70
End Cap
Page 75
Page 73
Hanger bolt
Page 63
Page 63
39
2
Insertion Rail
High quality – novotegra for
corrugated and sandwich roofs
40
System matrix corrugated | sandwich
The adjacent table lists possible combinations of mounting profiles and roof fixation. These apply to systems in both the clamp
version (p. 36) and insertion version (p. 38).
INSTALLATION
PROFILE
ARTICLENUMBER
DESIGNATION
251141
ALUVER
STANDARD
251142
ALUVER
PREMIUM
215115
C-RAIL
CATALOGU E
PAGE
251242ff
Hanger bolt for
wood M10 x 200
GPS1
62
251867ff
Base plate for stock
screw
M10/M12
94
251018
Stock screw bridge
short up to
200 mm
64
251019
Stock screw bridge
long up to
360 mm
64
214290
Stock screw set
(for wood) M10
63
214271ff
Stock screw set
(for wood) M12
63
214251ff
Stock screw set
(for steel) 8,0-M10
185
64
CATALOGUE PAGE
251140
ALUVER ECO
70
70
70
2
ROOF
FIXATION
70
41
Low installation workload – novotegra
for seamed metal roof
42
seamed metal roof
Main applications
Clamping system: Vertical assembly with standing seam
Clamping system: Vertical assembly with profiled sheet
S E A M E D M E TA L R O O F
2
Clamping system: Vertical assembly with round seam
Clamping system: Vertical assembly with standing seam
for copper roof
Your benefits
• Suitable for a variety of seamed
and profiled metal roofs
• Direct and centric load distribution
• Minimal material input
43
Seamed metal | Clamping system
Clamping system for vertical installation with standing seam
T H E C L A M P I N G SYST E M : P E R F ECT FO R S E A M E D M ETA L
R O O FS
Whether you have a standing seam roof, a round seam roof or a profiled
metal roof such as Zambelli RibRoof or Domico GBS, our proven clamp
mounting system ensures reliable, stable and secure attachment of the
photovoltaic system on every seamed metal roof.
Our patented seam clamp technology helps you attach the mounting
system directly to the roof seam, with the load distributed centrically in the
seam. Our client system for seamed metal roofs can also be used for
standing seam roofs made of copper. It offers high production quality and
durable and corrosion-resistant components. We have put our years of experience into every detail of our smart photo mounting system, making it
perfect for the individual requirements of your photovoltaic system on site.
Our clamping system can be secured quickly and easily on the seamed
metal roof. It consists of just three main components: the rails, the module
clamp, and the roof seam clamp, making it easy to assemble. The modules
are mounted vertically. The clamps are available in three different sizes,
and can be ordered in bare aluminium and black. Easily installed from
above, you can use them to secure any size of module frame to the seam
roof. The rails can be extended if required using external connectors. A rail
protrusion is also possible. Our clamping system for seamed metal roofs
offers excellent rear ventilation of the modules and an attractive look
thanks to the discrete system components and uniform module arrays.
Our free online tool Solar-Planit lets you configure your system quickly,
simply and in full compliance. You can also use it to perform structural
analysis in line with Eurocode load assumptions, even for international
sites.
44
A DVA N TAG E S
• Suitable for a variety of seamed and
profiled metal roofs
• Direct and centric load distribution
• Minimal material input
• Simple, Eurocode-compliant layout with
our Solar-Planit online tool
CLAMPING SYSTEM
Page 82
2
Connector
Page 77
Rail
Page 70
Seam clamp
Page 64
A2SS-saddel
(only for copper roofs)
Page 64
45
S E A M E D M E TA L R O O F
FIXATION SYSTEM
Flat roof
F L AT R O O F
3
3
Little to no ballast
thanks to improved
aerodynamics – novotegra
for flat roofs
48
Installation solutions for flat roofs
Main application
Membrane roof: East-West II
Membrane roof: Closed II
3
Gravel filling: Closed I cross brace
F L AT R O O F
Gravel filling: East-West I cross brace
• Membrane roof: East-West I
• Membrane roof: Closed I
• Membrane roof: Open 13°– 25°
• Membrane roof: South facing with insertion
system fixed on ballast stones
49
Flat roof | East-West
East-West II system for membrane roof
T H E E AST- W E ST S O LU T I O N FO R YO U R F L AT R O O F
A DVA N TAG E S
Our East-West II mounting system for flat roofs is perfect for fully exploiting the surface of your roof, allowing you to install almost double the module surface compared to south-facing systems. This means that electricity
is produced more evenly throughout the day. The East-West II mounting
system is a secure and stable system for flat roofs within incline of up to
5°, and is also quick and simple to construct. Based on our East-West I
mounting system, it offers the same high quality that has been proven for
years.
The mounting system is attached to the roof by its own weight, the
smart design and ballast consisting of gravel or heavy stones. The roof
membrane is not penetrated. The improved aerodynamics of our EastWest II elevation means that the system can be fitted with little to no ballast. This makes it well suited for flat roofs with low load-bearing capacity.
We have had the excellent security and stability of our East-West II mounting system scientifically confirmed in a series of wind tunnel tests.
The mounting system consists of only a few components, with the substructure laid in the module grid. The base foot and module support are
clicked in and the modules are clamped to the short side of the frame. The
base rail, which can also be used as a cable duct, has round edges and an
intermediate layer to protect the surface of the roof. The system is also
used on gravel roofs and offers flexibility with additional components such
as ballast trays.
Our range of supports ensures perfect load distribution, even at high
load requirements. The East-West II mounting system can be loaded with
2.4 kN/m² as standard. This increases to up to 4.8 kN/m² if the modules
are clamped on the long side. You can also use our Solar-Planit software
to plan your system quickly and reliably, as well as calculate ballast requirements and expansion joints.
50
• Excellent security and stability
• Wind tunnel tested
• No penetration of the roof membrane
• Quick installation
• Extremly low ballast needs due to
optimised aerodynamics
• Greater possible module surface
• Double support for high load requirement
BASIC COMPONENTS
Base trough
Page 71
Base trough connector set
Page 80
Aluminium edge protector
self-adhesive
Page 92
Flat roof mounting screw
Page 66
3
Page 87
F L AT R O O F
Base foot
EAST-WEST SYSTEM
Module support
Page 88
Ballast rearrangement
Page 72
Module bracket
Page 85 / 86
51
Flat roof | South-facing
Flat roof system closed configuration II for membrane roof
W I N D T U N N E L-T E ST E D SA F ET Y
A DVA N TAG E S
Do you want to mount an elevated photovoltaic system on your flat roof
facing south? Then our flat roof mounting system closed II is the right
solution for you. We have had the system put through its paces in a wind
tunnel, where it was tested under changing wind conditions and strong
wind peaks. The result confirms our years of proven quality, and with our
flat roof mounting system, you can be sure that you are getting excellent
safety and stability.
The closed configuration II mounting system is suited for flat roofs with
an incline of up to 5°, and impresses with its quick and simple assembly.
It consists of just a hand a full of individual components and system parts
that can be clicked in, with the modules clamped. The system can be
mounted without penetrating the roof. Heavy stones are usually used as
ballast, although the improved aerodynamics makes it possible for the system to be mounted with little to no ballast. This makes it perfect for your
flat roof. This is possible also thanks to our wind deflector, which is mounted overlapping on the elevation closed II and is securely connected to the
support and rails. This increases the general stability whilst also ensuring
perfect load distribution thanks to its connection to the base trough.
The base trough has wide, round and installation-friendly edges that
never cut in, and which also act as a cable duct that offers sufficient space
for cables and plugs. The closed configuration II flat roof mounting system
can also be used on gravel roofs, with additional components such as ballast trays also available. The mounting system can be loaded with 2.4 kN/m²
as standard, increasing to up to 4.8 kN/m² if the modules are clamped on
the long side. The closed configuration II flat roof mounting system is a
modified version of our proven flat roof mounting system closed configuration I. This means that your photovoltaic project benefits from the many
years of experience of our engineers.
52
• Excellent security and stability
• Wind tunnel tested
• No penetration of the roof membrane
• Quick installation
• Extremly low ballast needs due to
optimised aerodynamics
• Greater possible module surface
• Double support for high load
requirement
BASIC COMPONENTS
Base trough
Page 71
Base trough connector set
Page 80
Aluminium edge protector
self-adhesive
Page 92
Page 66
3
Page 87
F L AT R O O F
Base foot
SOUTH FACING CONFIGURATION
Module support
Page 87
Ballast rearrangement
Page 89
Module bracket
Page 85 / 86
53
4
In-roof | Facade
4
In-roof system
In-roof solution: PV generator and roof covering all in one
I N ST E A D O F T I L E S : T H E I N - R O O F SYST E M
It just looks good. Our in-roof photovoltaic mounting system helps you
create an aesthetic, uniform surface on the roof. The photovoltaic system
replaces the roof cover across either the entire surface or just sections of
it. Easily processed dummy modules and high-quality, optically fitting roof
windows complete the in-roof system, with all components kept black. Our
in-roof mounting system offers high safety, excellent production quality
and durability. It is suitable for every roof and is easy and very quick to
construct, even in comparison to other in-roof systems on the market.
The photovoltaic modules are fitted directly to the roof lathing without
hooks. The specially developed module frames are made in Switzerland,
with the final assembly of the modules and frames performed there too.
Our in-roof system fulfils the same requirements for water tightness as
roof tiles. This has been proven by identical tests by the testing and research institute Sursee. It can be used at pressure loads of up to 5.4 kN/m²,
with higher pressure loads possible if used with an additional support lathing. The modules are mounted horizontally with the frames overlapping.
Sturdy dummy modules enable a closed roof surface and an aesthetically pleasing result, and can be sawn to shape easily using a jigsaw or
circular saw. Snow guard dummy modules also allow the integration of a
snow guard system. The roof windows have been specially developed to
optically match our in-roof system, and are available in a range of sizes and
as double windows. These premium energy-saving windows are made
from wood and glass, and are fitted with a gas pressure spring. Both the
dummy modules and windows can be fitted seamlessly into the module grid.
We offer modules in three different performance classes for our in-roof
mounting system, making them perfect for every requirement. The choice
is yours.
56
A DVA N TAG E S
• Uniform and aesthetically pleasing
surface
• Flexibility thanks to different module
types
• Dummy modules allow visually
appealing integration of obstacles
• High-quality, visually appealing roof
windows
• Quick, hook-free installation
• Excellent rear ventilation of modules
• Snow guard for dummy module
Facade system
Optimal use for facades
C L E A R A D D E D VA LU E FO R YO U R FAC A D E
A DVA N TAG E S
• Uses the facade to generate electricity
• Creates modern, highly attractive facades
• Sizes range from a single module to
an entire facade
• Suspended construction away from
the building, with good rear ventilation
• For solid external walls
• Only for cold facades without heat
protection
4
• Quick, simple and compliant planning
with our configuration software
Our facade mounting system lets you use the outer wall of a building
to generate electricity instead of the roof. The photovoltaic system is suspended in front of the facade vertically – separated from the building and
with good rear ventilation. Our facade mounting system is mounted on
solid external walls made from tiles, stone or concrete. It is also mounted
exclusively on cold facades, i.e. walls with no external heat protection.
From industrial buildings to family homes, our mounting system helps you
create modern, visually appealing facades that add extra aesthetic value
to the building. All visible system components are available in bare aluminium and anodised black, and can be combined with modules ranging in
colour from blue to almost pitch black depending on the desired design.
The facade mounting system uses the same durable and corrosionresistant components as our roof-mounted systems, and works using the
same proven insertion technology. The modules are laid with the entire
length of the frame in the rails, keeping them stable, secure and protected.
The insertion rails enable quick and simple module assembly, even in vertical format. Installation is made even easier thanks to the low number of
individual components and preassembled parts. To secure the modules,
we use an approved set of dowels and stainless steel screws, which can be
used universally for a wide range of wall materials.
Our facade mounting system lets you install all common frame modules in both horizontal and vertical format, as well as a wide range of
frameless modules upon request. If you wish, we can expand your facade
photovoltaic system on all sides with perforated panel cladding, which protects the system against birds and small animals whilst ensuring good rear
ventilation.
57
5
Individual products
INDIVIDUAL PRODUCTS
5
Roof fixation
Flex roof hook set
Pan tile roof hook set for mounting C-rails as vertical and horizontal rails, optimised for narrow spans, rail-hook connection height adjustable up to 30 mm, hook-base
profile connection height adjustable for 24 – 30 mm ( flex 30 ) or 31– 40 mm ( flex 40 ) roof lathing, tile overlap up to 80 mm.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
210020
Flex roof hook set 30 M10
120
80
51 – 57
Alu / V2A
210025
Flex roof hook set 40 M10
120
80
57 – 67
Alu / V2A
Roof hook set ZD
Roof hook set for mounting C-rails as vertical and horizontal rails, rail connection height adjustable up to 35 mm, height-adjustable roof hook connection depending on
base profile for 24 – 30 or 31– 40 mm roof lathing, for tile overlaps up to 80 mm.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
210042
Roof hook set ZD 30 M12
155
126
52 – 58
Alu / V2A
210044
Roof hook set ZD 40 M12
155
126
58 – 68
Alu / V2A
Roof hook set BS
Roof hook set for mounting C-rails as vertical and horizontal rails on roofs with beavertail tiles, rail connection height adjustable up to 35 mm, height-adjustable roof
hook connection on base profile for 24 – 30 mm roof lathing, for tile overlaps up to 80 mm.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
214062
Roof hook set BS 30 M12
160
95
46 – 52
Alu / V2A
Flex double roof hook set
Roof hook set for mounting C-rails as horizontal rails, optimised for narrow spans and high loads, rail connection height adjustable up to 30 mm, height-adjustable roof
hook connection on base profile for 24 – 30 mm roof lathing, for tile overlaps up to 80 mm.
Art.-No.
60
Designation
a in mm
b in mm
c in mm
Material
210021
Double roof hook set flex 30 M10
230
80
51 – 57
Alu / V2A
210026
Double roof hook set flex 40 M10
230
80
57 – 67
Alu / V2A
Roof fixation
Double roof hook set ZD
Roof hook set for mounting C-rails as horizontal rails, optimised for high loads. Rail connection height adjustable up to 35 mm, height-adjustable roof hook connection
on base profile for 24 - 30 mm roof lathing, for tile overlaps up to 80 mm.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
210043
Double roof hook set ZD 30 M12
245
210045
Double roof hook set ZD 40 M12
245
125
52 – 58
Alu / V2A
125
58 – 68
Alu / V2A
Double Roof hook set BS
Roof hook set for mounting C-rails as horizontal rails on roofs with beavertail tiles, optimised for high loads, rail connection height adjustable up to 35 mm, height-adjustable roof hook connection on base profile for 24 - 30 mm roof lathing, for tile overlaps up to 80 mm.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
214063
Double Roof hook set BS 30 M12
260
95
46 – 52
Alu / V2A
Roof hook 533
Roof hooks for ALUVER mounting rails as vertical rails, rail connection height adjustable up to 26 mm, with fluting in slot 8.5 x 35 mm, for tile overlaps up to approx.
100 mm and 30 mm roof lathing. Available preassembled with M8 bolt.
Art.-No.
Designation
a in mm
b in mm
c in mm
251020
Cast aluminium roof hook, S-shaped
181
71
46
Material
Alu cast
251024
Roof hook 533, with bolt
181
71
46
Alu / V2A
Roof hook 633
5
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
252786
Pan tile hook 633 ALU vertical flex3
100
70
40 – 55
Alu cast
61
INDIVIDUAL PRODUCTS
Roof hooks for ALUVER mounting rails as vertical rails, rail connection height adjustable up to 26 mm in slot 8.5 x 35 mm with fluting, roof hook position in foot area
adjustable by +/-50 mm from central position, for tile overlaps up to 100 mm, base plate with round holes 7 mm.
Roof fixation
Roof hook 544
Roof hooks for ALUVER mounting rails as horizontal rails, rail connection height adjustable up to 26mm, with fluting in slot 8.5 x 35mm, for tile overlaps up to approx.
100 mm and 30mm roof lathing. Available preassembled with M8 bolt.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
251021
Cast aluminium roof hook, S-shaped
181
71
46
Alu cast
251025
Roof hook 544, with bolt
181
71
46
Alu / V2A
Plain tile hook A2
Roof hooks for ALUVER mounting rails as vertical and horizontal rails on roofs with beavertail tiles, rail connection with adapter set, slot 11 x 41 mm, for 24 mm roof
lathing. Available preassembled with underlay plate and screws.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
251011
Plain tile hook A2 stainless, C-shaped
300
30
120
V2A
251012
Plain tile hook A2 stainless with underlay plate
300
30
120
V2A / gav. steel
Slate hook A2
Roof hooks for ALUVER mounting rails as vertical and horizontal rails on roofs with slate or shingle covering, rail connection with adapter set, slot 11 x 41 mm,
with flat foot area.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
251158
Slate hook A2
250
30
70
V2A
Hanger bolt for wood M10
Hanger bolt with hexagon SW 7 drive and base plate for ALUVER mounting rails as vertical and horizontal rails on wooden rafters or purlins, premounted
with EPDM sealing, available in a range of sizes.
62
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
251242
Hanger bolt for wood M10x200, GPS1/EPDM
70
10
120
V2A / Alu
Roof fixation
Hanger bolt for wood M12
Hanger bolt with hexagon SW 9 drive and base plate for ALUVER mounting rails as vertical and horizontal rails on wooden rafters or purlins, premounted
with EPDM sealing and SW 18 nuts, available in a range of sizes.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
251243
75
15
110
V2A/Alu
251244
90
10
150
V2A/Alu
251245
100
40
160
V2A/Alu
Stock screw set (for wood)
Hanger bolt with Torx 30 drive for mounting C-rails or stock screw bridges as vertical or horizontal rails on wooden rafters or purlins, premounted
with EPDM sealing, available in a range of sizes.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
214270
Stock screw set (for wood) M10 200 mm
75
25
100
V2A
214280
75
75
100
V2A
214290
75
75
150
V2A
214271
75
25
100
V2A
214281
75
75
100
V2A
214291
75
75
150
V2A
c in mm
Material
Stock screw set (for wood)
Hanger bolt with 6 mm internal hex socket for securing on wooden rafters or purlins, available on request in a range of sizes.
Designation
a in mm
b in mm
214261
Stock screw set (for wood) 8,4-M10 160 mm
70
10
70
V2A
214263
90
20
70
V2A
214265
100
30
70
V2A
214267
120
40
70
V2A
214269
130
50
70
V2A
5
63
INDIVIDUAL PRODUCTS
Art.-No.
Roof fixation
Stock screw set (for steel)
Hanger bolt with 6 mm internal hex socket for securing on steel purlins, available on request in a range of sizes.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
V2A
214251
Stock screw set (for steel) 8,0-M10 140 mm
65
10
50
214253
65
55
50
V2A
214255
65
90
50
V2A
214257
65
130
50
V2A
Stock screw bridge
Stock screw bridge for mounting on two hanger bolts/solar fasteners with 25 x 12 mm slots, adjustable slides for variable positioning of installation rails, for raised bead
intervals of 110 - 210 mm or 170 - 350 mm, delivered preassembled, available in two different sizes
Art.-No.
Designation
251018
Stock screw bridge short up to 220 mm
251019
Stock screw bridge long up to 360 mm
a in mm
b in mm
c in mm
Material
75
250
65
Alu
75
390
65
Alu
Standing seam clamp
Clamp for mounting the C-rail on standing seam, consisting of a grub screw with corresponding assembly tool for securing the clamp on the seam, as well as a nut with
SW13 hexagon drive for fastening C-rails, available with stainless steel saddle with material thickness of 0.5 mm for mounting on copper roofs.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
210530
Standing seam clamp set M8
25
30
48
Alu / V2A
210531
Standing seam clamp set M8 for copper
25
30
16
Alu / V2A
Round seam
Clamp for mounting the C-rail on round seam, consisting of a grub screw with corresponding assembly tool for securing the clamp on the seam, as well as a nut with
SW 13 hexagon drive for fastening C-rails.
64
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
210535
Rounded seam clamp set M8
45
30
65
Alu / V2A
Roof fixation
Profiled metal sheet clamp
Clamp for mounting the C-rail on Zambelli RibRoof 500 metal profile roofs, consisting of two screws for securing the clamp, as well as a nut with SW 13 hexagon drive.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
210515
Profiled metal sheet clamp set Z M12
62
50
80
Alu / V2A
Profiled metal sheet clamp
Clamp for mounting the C-rail on Zambelli RibRoof 500 metal profile roofs, consisting of two screws for securing the clamp, as well as a nut with SW 13 hexagon drive.
Art.-No.
Designation
a in mm
210510
Profiled metal sheet clamp set ZD M12
18,8
210512
A2SS-saddel for profiled metal sheet clamp ZD
16
b in mm
c in mm
Material
30
55
Alu / V2A
30
26
V2A
Trapez sheet bracket
Bracket for attachment to trapezoidal roofs, consisting of two thin sheet screws with SW 8 hexagon drive and an EPDM seal on the roof-facing side, for bead heights of
25 mm and 35 mm, available in two different sizes.
Art.-No.
Designation
a in mm
b in mm
251248
Trapez sheet bracket 40 × 126 complete
126
40
c in mm
Material
V2A
251247
Trapez sheet bracket 45 × 141 complete
141
45
V2A
65
INDIVIDUAL PRODUCTS
5
Roof fixation
Direct base profile mounting set
Mounting set consisting of 2 drill screws with SW 8 hexagon drive and an EPDM seal 130 x 45 mm for attaching base profiles on trapezoidal roof raised beads.
Art.-No.
Designation
a in mm
210050
Direct base profile mounting set
25
b in mm
c in mm
Material
V2A / EPDM
Indirect mounting set for base profile
Mounting set consisting of 4 drill screws with SW 8 hexagon drive for attaching the base profile on the C-rail or base trough.
Art.-No.
Designation
a in mm
210060
Indirect mounting set for base profile
25
b in mm
c in mm
Material
V2A
Mounting screw
Screw with SW 8 hexagon drive for chipless attachment of the base profile to the base trough Available as drill screw or chipless variant.
Art.-No.
Designation
a in mm
218030
25
b in mm
c in mm
Material
V2A
218033
Flat roof mounting screw SL 5,5
25
V2A
C-rail direct mounting set
Mounting set consisting of two thin sheet screws with SW 8 hexagon drive and EPDM seal for chipless attachment of the C-rail to the trapezoidal roof.
66
Art.-No.
Designation
a in mm
214195
C-rail direct mounting set chipless
25
b in mm
c in mm
Material
V2A / EPDM
Roof fixation
Roof hook mounting screw
Wood screw with Torx 25 drive, diameter = 6 mm, length = 30 – 150 mm for various roof hooks. Available in stainless or galvanised steel.
Art.-No.
Designation
a in mm
214070
Roof hook mounting screw 6 × 30
30
b in mm
c in mm
Material
Gav. steel
214071
60
Gav. steel
214072
90
Gav. steel
214073
120
Gav. steel
214074
150
Gav. steel
214078
Roof hook mounting screw 6 × 30 V2A
30
V2A
214079
60
V2A
214080
90
V2A
214081
120
V2A
214082
150
V2A
Roof hook mounting screw
Wood screw with Torx 40 drive or AW drive, diameter = 8 mm, length = 100 – 340 mm.
Art.-No.
Designation
a in mm
214086
100
b in mm
c in mm
Material
214087
140
Gav. steel
214088
180
Gav. steel
Gav. steel.
214089
220
Gav. steel
214090
260
Gav. steel
214091
300
Gav. steel
214092
340
Gav. steel
251087
Wood screw 8 × 100 Stvz Washer head AW3.0
100
Gav. steel
251088
120
Gav. steel
251089
140
Gav. steel
251090
260
Gav. steel
Fixing anchor
5
Fixing anchor with SW 17 drive, length = 95 - 130 mm, made from stainless steel, for cracked and uncracked concrete.
Designation
a in mm
b in mm
c in mm
Material
251056
Fixing anchor M10 / 15 / 95 A4, for concrete
95
V2A
251539
Fixing anchor M10 / 50 / 130 A4, for concrete
130
V2A
67
INDIVIDUAL PRODUCTS
Art.-No.
Rails
Insertion Rail
Insertion rail for inserting framed modules with a frame height of 31– 50 mm, available in black anodised or bare.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
251473 / 218110
Insertion Rail 31 6,00 m
56
31
Alu
252509 / 218141
56
33
Alu
251474 / 218111
56
35
Alu
251486 / 218112
56
36
Alu
251476 / 218113
56
38
Alu
251477 / 218114
56
40
Alu
251478 / 218115
56
41
Alu
251479 / 218116
56
42
Alu
251480 / 218117
56
43
Alu
251481 / 218118
56
45
Alu
251482 / 218119
56
46
Alu
251483 / 218120
56
50
Alu
251484 / 218130
Insertion Rail 31 6,00 m sw
56
31
Alu
252510 / 218142
56
33
Alu
251485 / 218131
56
35
Alu
251475 / 218132
56
36
Alu
251487 / 218133
56
38
Alu
251488 / 218134
56
40
Alu
251489 / 218135
56
41
Alu
251490 / 218136
56
42
Alu
251491 / 218137
56
43
Alu
251492 / 218138
56
45
Alu
251493 / 218139
56
46
Alu
251494 / 218140
56
50
Alu
ALUTEC Insertion Rail frameless
Insertion rail for inserting frameless modules with a glass thickness of approx. 7 mm. Additional EPDM T-units are required for securing the laminate module.
68
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
251038
ALUTEC Insertion Rail frameless 6,05m
69
48
17
Alu
Rails
ALUTEC-Plus rail
Insertion rail for inserting framed modules with a frame height of 40 mm for high snow loads, with the option of attaching a snow guard system.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
251037
ALUTEC-Plus rail 40, enforced, 6m
69
60
41
Alu
c in mm
Material
Support Rail IR
Support rail between the insertion rails at high module load.
Art.-No.
Designation
a in mm
b in mm
251495 / 218150
Support Rail IR 6,00 m
39
17
Alu
Short rail 200
Short rail with EPDM rubber seal for horizontal module mounting on trapezoidal roofs. Available in two sizes for varying module rear ventilation.
Art.-No.
Designation
a in mm
b in mm
215420
Short rail C47 with EPDM 200 mm
52
47
c in mm
Alu / EPDM
Material
215422
52
71
Alu / EPDM
Short rail 385
5
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
215421
52
47
12
Alu / EPDM
69
INDIVIDUAL PRODUCTS
Short rail for vertical module mounting on trapezoidal roofs.
Rails
ALUVER mounting rail
Installation rail, for use as a module support rail in clamped systems or as a cross rail, available in different dimensions for various spans and loads depending on the
structural requirement. With fluting for simple, lateral screw connection.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
251140
ALUVER mounting rail Eco 22 x 50, 6 m
22
50
Alu
251141
ALUVER mounting rail Standard 30 x 50, 6 m
30
50
Alu
251142
ALUVER mounting rail Premium 40 x 60, 6 m
40
60
Alu
251143
ALUVER mounting rail L 50 x 90, 6 m
50
90
Alu
C-rail
Installation rail, for use as a module support rail in clamped systems or as a cross rail, available in different dimensions for various spans and loads depending on the
structural requirement. Rail base with slots in 10 cm grid for simple installation from above.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
215112
C-rail 95-3 6,12 m
52
95
Alu
215120
C-rail 71-2 6,12 m
52
71
Alu
215115
C-rail 47-2 6,12 m
52
47
Alu
215117
C-rail 47-2 4,20 m
52
47
Alu
VARIOTECC profi le pair
Rail pairs consisting of head and foot rails with flexible connection. Combined use of rail pairs H 45 and H 136 for variable elevation of modules at an angle of approx.
3-18°.
70
Art.-No.
Designation
a in mm
b in mm
251254
VARIOTECC profile pair H 45, 6 m
56
45
c in mm
Material
Alu
251253
VARIOTECC profile pair H 136, 6 m
56
136
Alu
Rails
Base profile
Module support rail for module elevation on flat roofs, as well as trapezoidal, corrugated and sandwich roofs.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
215505
Base profile 6,12 m
130
67
27
Alu
215506
130
67
27
Alu
215507
130
67
27
Alu
Base trough
Base trough for attaching the base profile, base foot or module supports, and for inserting the ballast. Available bare and preassembled with intermediate layer.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
218005
Base trough 150-30 6,00 m
150
30
Alu
218081
Base trough 150-30 with intermediate layer 5,00 m
150
30
Alu / PE
218082
Base trough 150-30 with intermediate layer 6,00 m
150
30
Alu / PE
71
INDIVIDUAL PRODUCTS
5
Rails
Base trough
Base trough for ballast with on-site gravel for attaching the base profile, available in various lengths.
Art.-No.
Designation
a in mm
b in mm
218051
230
90
c in mm
Material
Alu
218052
230
90
Alu
Support Brace
For optimised force distribution between the modules for attachment on the module support sets. Slots enable improved water runoff.
Available in two different lengths.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
218105
Support Brace 20 x 20 x 1,5 5,15 m
20
20
Alu
218109
Support Brace 20 x 20 x 1,5 1,75 m
20
20
Alu
Rounded pipe ALU
Rounded pipe for use as a snow guard system. Secured to the Alutec-PLUS rail with snow guard bracket. Available as 0.8 m or 6.0 m.
72
Art.-No.
Designation
a in mm
b in mm
251007
Rounded pipe ALU 20 x 5 snowguard 6,00 m
20
5
c in mm
Material
Alu
251008
Rounded pipe ALU 20 x 5 snowguard L 800
20
5
Alu
Module slip guard
Slip guard for securing the modules when mounted on the roof. Available for different frame bores.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
21645
Module slip guard M8
25
V2A
21640
Module slip guard M6
25
V2A
216506
Module slip guard set KR
20
V2A
Slip guard
Slip guard set with SW 18 hexagon drive for securing the modules in horizontal installation on short rails.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
216505
Slip guard set short profile M14
30
30
53
Alu / V2A
Slip Guard/ End Cap
Slip guard set for securing the modules in horizontal installation or as a cover for the C-rails. Available in bare aluminium or black anodised variants to match the frame
colour.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
210090
Slip Guard / End Cap Set C47
53
80
80
Alu / V2A
210091
Slip Guard / End Cap Set C47 sw
53
80
80
Alu / V2A
210092
53
100
80
Alu / V2A
Alu / V2A
210093
Slip Guar / End Cap Set C71 sw
53
100
80
210094
53
130
80
Alu/V2A
210095
Slip Guard / End Cap Set C95 sw
53
130
80
Alu / V2A
Top cover base trough
5
Top cover protects the base trough and ensures neat routing of the solar cable.
Designation
a in mm
b in mm
218070
Top cover base trough 150-30 3,00 m
154
15
c in mm
Material
Alu
73
INDIVIDUAL PRODUCTS
Art.-No.
Top cover C-rail
Protective top cover clips into the C-rail and ensures neat routing of the solar cable.
Art.-No.
Designation
a in mm
b in mm
218071
Top cover C-rail 2.000 mm
50
3
c in mm
Material
Alu
Adapter top cover C-Rail
Adapter for use of the Top cover C-rail 2.000 mm with the East-West I flat roof application.
Art.-No.
Designation
a in mm
b in mm
218072
Adapter top cover C-Rail
50
17
c in mm
Material
Alu
Insertion rail end cap
Uniform edge stop for insertion rails with different inner dimensions, secured with AW30 drive. Available in bare metal and black anodised variants.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
251157 / 218158
Insertion rail end cap set, schwarz
49
49
Alu
251154 / 218159
Insertion rail end cap set
49
49
Alu
Edge stop for ALUTEC FL
Edge stop for ALUTEC Insertion Rail frameless or ALUTEC-Plus rail, with EPDM seal, secured with SW 8 hexagon drive.
74
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
251156
Edge stop set for ALUTEC FL
70
50
50
Alu
Edge stop for ALUTEC Plus
p for ALUTEC-Plus rail, secured with AW 30 drive.
Art.-No.
Designation
a in mm
b in mm
252367
Edge stop set for ALUTEC Plus
75
75
c in mm
Material
Alu
Edge stop for VARIOTECC
Edge stop for rail pair RL VARIOTECC, profile pair H 136, secured with SW 8 hexagon drive.
Art.-No.
Designation
a in mm
b in mm
251430
Edge stop for RL VARIOTECC set L
71
88
c in mm
Material
Alu
EPDM T-unit
EPDM T-piece for securing modules in insertion rails against wind load at low module inclines < 10°, as well as against unauthorised removal at accessible areas. Available for modules with and without frames.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
251043 / 218153
EPDM T-unit IR
84
17
EPDM
251042
EPDM-T-Stück, laminate module
40
22
EPDM
End cap for ALUVER
5
End caps in different sizes for various ALUVER mounting rails. Made from UV and weather-resistant PA 6.6 in black.
Designation
a in mm
b in mm
251098
End cap for ALUVER Eco
22
50
251100
End cap for ALUVER Standard
30
50
PA 6.6
251099
End cap for ALUVER Premium
40
60
PA 6.6
c in mm
Material
PA 6.6
75
INDIVIDUAL PRODUCTS
Art.-No.
Mounting Insertion Rail
Connector for securing the insertion rail with C-rail, nut with SW 13 hexagon drive.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
215419
Mounting Set Insertion Rail M8
66
50
13
Alu / V2A
ALUTEC retaining clip
Connector for securing the insertion rail with ALUVER mounting rail, rail base 40x60x250 and CREOFLEX triangles, nut with SW 13 hexagon drive,
delivered preassembled.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
251009
ALUTEC retaining clip with slot bolt
66
50
13
Alu / V2A
ALUTEC retaining clip high
Connector for securing the insertion rail with ALUVER mounting rail, rail base 40x60x250 and CREOFLEX triangles, nut with SW 13 hexagon drive,
delivered unassembled.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
251079
ALUTEC retaining clip high, slot nut set
33
50
15
Alu / V2A
ALUVER retaining clip
Connector for securing ALUVER mounting rails to each other and to CREOFLEX triangles, nut with SW 13 hexagon drive,
delivered unassembled.
76
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
251078
ALUVER retaining clip, slot nut set
35
30
22
Alu / V2A
Cross rail connector
Connector for securing C-rails to each other to create a cross rail configuration. Delivered unassembled.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
215415
Cross rail connector set M14
30
46
34
Alu / V2A
Expansion joint 47
Connector measuring 325 mm in length for rail joint between two C-rails 47 with two round-head screws and nuts with SW 18 hexagon drive. Available in non-locating
bearing design with four round-head screws, in order to compensate for expansions in the system.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
215200
Rail Connector set 47
52
40
50
Alu/V2A
21530
Expansion joint 47
52
40
50
Alu / V2A
Rail connector set 71
Connector measuring 490 mm in length for rail joint between two C-rails 71 with four round-head screws and nuts with SW 18 hexagon drive. Available in non-locating
bearing design, in order to compensate for expansions in the system.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
215308
52
67
50
Alu / V2A
215315
Expansion joint 71
52
67
50
Alu / V2A
77
INDIVIDUAL PRODUCTS
5
Connector measuring 500 mm in length for rail joint between two C-rails 95 with four round-head screws and nuts with SW 18 hexagon drive.
Available in non-locating bearing design, in order to compensate for expansions in the system.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
215310
52
70
50
Alu / V2A
215320
Expansion joint 95
52
70
50
Alu / V2A
Rail Connector IR
Connector measuring 150 mm in length for rail joint between two insertion rails. Attached as non-locating bearing at one end of the rail using a grub screw.
Available in bare metal or black anodised.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
251266 / 218151
Rail Connector set IR
65
18
Alu / V2A
251268 / 218152
Rail Connector set IR sw
65
18
Alu/ V2A
Connector ALUVER FL
Connector measuring 150 mm in length for rail joint between two ALUTEC Insertion Rail frameless. Can be attached as non-locating bearing at one end of the rail
using a grub screw.
Art.-No.
Designation
a in mm
b in mm
251267
Connector set ALUVER FL rail
78
31
c in mm
Material
Alu
Connector for ALUTEC on traoezoidal roof
Connector measuring 100 mm for rail joint between two insertion rails for direct installation on trapezoidal roof in combination with the trapezoidal bracket.
78
Art.-No.
Designation
a in mm
251255
Connector for ALUTEC with TSM4, A2, 100x5
5
b in mm
c in mm
Material
Alu / V2A
Connector for ALUTEC-Plus
Connector measuring 200 mm in length for rail joint between two ALUTEC-Plus rails.
Art.-No.
Designation
a in mm
b in mm
251256
Conector ALUTEC Plus
10
30
c in mm
Material
Alu
Connector ALUVER rail
Connector measuring 200 mm in length for rail joint between two corresponding ALUVER mounting rails with two self-drilling sheet screws with SW 8 hexagon drive.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
251269
Connector set ALUVER Eco rail
19
38
200
Alu
251272
Connector set ALUVER Standard rail
27
41
150
Alu
Connector ALUVER rail
Connector measuring 200 mm in length for rail joint between two corresponding ALUVER mounting rails with two self-drilling sheet screws with SW 8 hexagon drive.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
251271
Connector set ALUVER Premium rail
36
56
150
Alu
251270
Connector set ALUVER L rail
45
85
400
Alu
Connector VARIOTECC F113
5
Connector measuring 150 mm in length for rail joint between two VARIOTECC foot rails 113 with thin sheet screws with SW 8 hexagon drive.
Designation
a in mm
b in mm
251273
Connector set VARIOTECC F113 ALU
12
50
c in mm
Material
Alu
79
INDIVIDUAL PRODUCTS
Art.-No.
Connector VARIOTECC F22
Connector measuring 160 mm in length for rail joint between two VARIOTECC F22 rails.
Art.-No.
Designation
a in mm
b in mm
251263
Connector VARIOTECC F22 ALU 160 x 22 x 5
5
22
b in mm
c in mm
Material
Alu
Connector for snowguard pipe
Snow guard pipe connector measuring 200 mm in length for joining two snow guard profiles.
Art.-No.
Designation
a in mm
251261
Connector for snowguard pipe
8
c in mm
Material
Alu
Base trough connector 150-30 I
Connector measuring 380 mm in length for rail joint between two base troughs 150-30.
Art.-No.
Designation
a in mm
b in mm
218036
Base trough connector set 150-30 I
16
26
c in mm
Material
Alu
Base trough expansion joint
Connector measuring 380 mm in length with expanding joint for compensating thermally related displacements.
80
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
218012
Base trough expansion joint 150-30
150
30
80
Alu
Connector base profi le
Connector measuring 380 mm in length for rail joint between two base profiles. Available in non-locating bearing design, in order to compensate
for expansions in the system.
Art.-No.
Designation
a in mm
b in mm
215512
Connector base profile
41
68
215514
Base profile expansion joint
41
68
c in mm
Material
Alu
80
Alu
Angled base profile connector (rise)
Connector measuring 380 mm in length for rail joint between two base profiles on flat roofs with two or more opposing pitched roof surfaces.
Suitable for angles of 2° to 5°.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
218013
Angled base profile connector 3° (rise)
41
68
150
Alu
Angled base profile connector (dip)
Connector measuring 380 mm in length for rail joint between two base profiles on flat roofs with two or more opposing pitched roof surfaces.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
218014
Angled base profile connector 3° (dip)
41
41
150
Alu
Angled base trough connector 150-30
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
218011
Angled base trough connector 150-30 3°
25
25
180
Alu
81
INDIVIDUAL PRODUCTS
5
Connector measuring 380 mm in length for rail joint between two base troughs 150-30 G/K 3° on flat roofs with two or more opposing pitched roof surfaces.
Module bracket
End clamp
Clamp for securing the end modules of a module array to C-rails. For frame heights of 28 – 33 mm / 34 – 42 mm / 43 – 52 mm, available in bare metal
and black anodised variants.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
216209
End clamp 28-33 Set black
52
24
45 – 51
Alu / V2A
216208
End clamp 28-33 Set
52
24
45 – 51
Alu / V2A
216333
52
24
52 – 60
Alu / V2A
216332
End clamp 34-42 Set
52
24
52 – 60
Alu / V2A
216213
52
24
63 – 71
Alu / V2A
216212
End clamp 43-52 Set
52
24
63 – 71
Alu / V2A
Middle clamp
Clamp for securing the central modules of a module array to C-rails. For frame heights of 28 – 33 mm / 34 – 42 mm / 43 – 52 mm, available in bare metal
and black anodised variants.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
216009
Middle clamp 28-33 Set black
52
33
45 – 51
Alu / V2A
216008
Middle clamp 28-33 Set
52
33
45 – 51
Alu / V2A
216303
52
33
52 – 60
Alu / V2A
216302
52
33
52 – 60
Alu / V2A
216013
52
33
61 – 71
Alu / V2A
216012
52
33
61 – 71
Alu / V2A
End clamp
Clamp with spring mechanism for securing the end modules of a module array to ALUVER mounting rails. For frame heights of 31 – 40 mm or 41 – 50 mm,
available in bare metal and black anodised variants.
82
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
251110
End clamp CITO 31 – 40 mm, black
80
34
42 – 51
Alu / V2A
251111
End clamp CITO 31 – 40 mm
80
34
42 – 51
Alu / V2A
251112
End clamp CITO 41 – 50 mm, black
80
34
52 – 61
Alu / V2A
251113
End clamp CITO 41 – 50 mm
80
34
52 – 61
Alu / V2A
Module bracket
Middle clamp
Clamp with spring mechanism for securing the central modules of a module array to ALUVER mounting rails. For frame heights of 31 – 40 mm or 41 – 50 mm,
available in bare metal and black anodised variants.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
Alu / V2A
251124
Middle clamp CITO 31 – 40 mm, black
80
39
42 – 51
251125
Middle clamp CITO 31 – 40 mm
80
39
42 – 51
Alu / V2A
251126
Middle clamp CITO 41 – 50 mm black
80
39
52 – 61
Alu / V2A
251127
Middle clamp CITO 41 – 50 mm
80
39
52 – 61
Alu / V2A
Spacer
Spacer measuring 60 mm in length for the CITO end clamp, made from UV and weather-resistant PA 6.6 L. Available in different sizes according to
module frame height.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
251026
Spacer for CITO end clamp, 31 – 32 mm
251027
60
11
1
PA 6.6
60
15
5
251028
PA 6.6
60
18
8
PA 6.6
251029
60
20
251030
60
22
12
PA 6.6
Alu
251031
60
25
15
PA 6.6
251032
60
29
19
PA 6.6
251033
60
30
Alu
83
INDIVIDUAL PRODUCTS
5
Module bracket
End clamp VELOX
Clamp for securing frameless end modules of a module array to ALUVER mounting rails. Delivered fully preassembled. Laminate clamps for additional module types
and glass thicknesses available on request.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
251104
End clamp VELOX laminate 7 mm
80
29
6,2 – 9,7
Alu / EPDM
Middle clamp VELOX
Clamp for securing frameless modules of a module array to ALUVER mounting rails. Delivered fully preassembled. Laminate clamps for additional module types
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
251106
Middle clamp VELOX laminate 7 mm
80
43
6,2 – 9,7
Alu / EPDM
End clamp SIMPLEX
Clamp for securing frameless end modules of a module array to ALUVER mounting rails. Delivered fully preassembled. Laminate clamps for additional module types
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
251103
End clamp SIMPLEX laminate 7 mm
70
34,5
7,6
Alu / EPDM
Middle clamp SIMPLEX
Clamp for securing frameless modules of a module array to ALUVER mounting rails. Delivered fully preassembled. Laminate clamps for additional module types and
glass thicknesses available on request.
84
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
251105
Middle clamp SIMPLEX laminate 7 mm
70
54
7,6
Alu / EPDM
Elevation
Module bracket front
Clamp for securing modules of different frame sizes on the base profile. 2 clamps required per module, delivered preassembled with all connection material.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
210030
Module bracket set front
100
8
4
Alu / V2A
Module bracket set front direct (box fr.)
Clamp for elevating modules with box frame on the base profile. Manufacturer's approval granted for elevation of Solar-Fabrik and SolarWorld modules.
2 clamps required per module, delivered preassembled with all connection material.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
210031
Module bracket set front direct (box fr.)
50
36
5,5
Alu / V2A
Module bracket set back
Clamp for securing modules of different frame sizes on the module support sets. 2 clamps required per module, delivered preassembled with all connection material.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
210035
Module bracket set back
65
8
4
Alu / V2A
Flat Roof End Clamp (Short side)
Clamp with T-adapter for securing modules at the edge of a module array on the short frame side with frame heights of 28 – 33 mm / 34 – 42 mm / 43 – 52 mm
for module support sets 13° or base foot set 13°. Delivered fully preassembled.
Designation
218100
Flat Roof End Clamp (Short side) E-K 28-33
218101
Flat Roof End Clamp (Short side) 34-42
218102
Flat Roof End Clamp (Short side) 43-52
52
a in mm
b in mm
c in mm
Material
52
60
38 – 43
Alu / V2A
52
60
44 – 52
Alu / V2A
60
53 – 62
Alu / V2A
85
INDIVIDUAL PRODUCTS
Art.-No.
5
Elevation
Flat Roof End Clamp
Clamp for securing modules at the edge of a module array on the long frame side with frame heights of 28 – 33 mm / 34 – 42 mm / 43 – 52 mm to module support sets
13° or base foot set 13°. Delivered fully preassembled.
Art.-No.
Designation
a in mm
b in mm
c in mm
218094
Flat Roof End Clamp 28 – 33
218095
218096
52
Material
52
24
32
Alu / V2A
52
24
37
Alu / V2A
24
45
Alu / V2A
Flat Roof Mid Clamp
Clamp for securing modules at the centre of a module array on the short frame side with frame heights of 28 – 42 mm / 43 – 52 mm to module support sets 13° or base
foot set 13°. Delivered fully preassembled.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
218103
Flat Roof Mid Clamp 28 – 42
52
33
11,4
Alu / V2A
218104
Flat Roof Mid Clamp 43 – 52
52
33
11,4
Alu / V2A
Module bracketset back east-west
Clamp for support set 230 east-west / module support set east-west 150 in combination with the C-rail. For securing modules at the edge of a module array on the long
frame side with frame heights of 28 – 33 mm / 34 – 42 mm / 43 – 52 mm. Delivered fully preassembled.
86
Art.-No.
Designation
a in mm
b in mm
218043
Module bracketset back east-west 28 – 33 mm
159
52
c in mm
Alu / V2A
Material
218044
Module bracketset back east-west 34 – 42 mm
159
52
Alu / V2A
218045
Module bracketset back east-west O-W 43 – 52 mm
159
52
Alu / V2A
Elevation
Base foot
Module support for the front side of the module for installation in the base trough. Assembly tool for easy installation available.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
218091
Base foot set 13° 150 – 30
80
37
53
Alu
Module support
Support for elevating the modules in a single-layer configuration when using the base trough. Suitable for securing the wind deflector 13°.
Assembly tool for easy installation available.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
218092
Module support set 13° 150 – 30
265
83
60
Alu
Module support
Support for elevating the modules for different elevation angles. Angle of elevation freely adjustable. 2 required per module.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
210018
Module support set 520 mm
520
100
100
Alu
210016
440
100
100
Alu
210014
360
100
100
Alu
210012
280
100
100
Alu
210010
200
100
100
Alu
87
INDIVIDUAL PRODUCTS
5
Elevation
Module support
Support for elevating modules with box frames at an elevation angle of 13°. For frame thicknesses 28 – 33 mm / 34 – 42 mm. 2 required per module.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
218023
Module support Set 13° 28 – 33 mm
255
50
Alu / V2A
218021
Module support Set 13° offen 34 – 42 mm
255
50
Alu / V2A
Module support 13°
Support for elevating and securing modules at the quarter point for frame thicknesses 28 – 33 mm / 34 – 42 mm / 43 – 52 mm. 2 required per module.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
218016
Module Support Set 13° 28 – 33 mm
255
50
Alu / V2A
218015
255
50
Alu / V2A
218020
255
50
Alu / V2A
Module suport east-west
Support for East-West module elevation in a single-layer configuration. Also available as a variant for higher structural requirements.
88
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
218108
Module support set 13° 150 – 30 Ost-West 2S
281
60
120
Alu
218107
Module support set 13° 150 – 30 Ost-West 1S
281
60
120
Alu
Elevation
Module support east-west
Support for placing and securing the C-rail 71 in an East-West I elevation on the base trough 230 – 90. Available for base troughs 230 – 90 and 150 – 30.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
218042
Support set 230 east-west
190
50
60
Alu / V2A
218041
Support set 150 east-west
210
50
50
Alu / V2A
Wind Defl ector
Wind deflector for improved wind deflection and lower ballast for closed II flat roof variants. Secured with three attachment screws to the module support set 13° and
the base trough.
Art.-No.
Designation
a in mm
b in mm
218097
Wind Deflector 13° 1,85 m
270
110
c in mm
Material
Alu
Wind Defl ector
Wind deflector for improved wind deflection and lower ballast for closed I flat roof variants. Installed in combination with the module support set 13° 34 – 42 mm /
43 – 52 mm.
Art.-No.
Designation
a in mm
b in mm
218000
Wind Deflector 13° 1,72 m
330
23
c in mm
Material
Alu
Wind Defl ector east-west
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
218180
Wind Deflector 13° 1,85 m east-west
241
175
65
Alu
89
5
INDIVIDUAL PRODUCTS
Wind deflector for improved wind deflection and lower ballast for closed II flat roof variants. Secured with three attachment screws to the module support set 13° and
the base trough.
Elevation
Ballast trough
Optional ballast trough for large ballast or for suspension in the base trough if using lots of ballast. Available with an intermediate layer or in bare aluminium.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
218025
Ballast trough 120 – 30 530 mm
144
32
120
Alu
218026
Ballast trough 120 – 30 530 mm with intermediate layer
144
32
120
Alu / PE
CREOFLEX triangle
Triangles in different sizes with two variable elevation angles, mountable on flat and pitched roofs. Module fastening possible with module clamps or insertion rails.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
251057
CREOFLEX triangle 15 / 20°, L 1100
1057
1100
285 / 376
Alu
251063
1057
1100
465 / 550
Alu
251058
1309
1300
336 / 445
Alu
251064
1309
1300
549 / 650
Alu
251059
1547
1500
388 / 513
Alu
251065
1547
1500
634 / 750
Alu
Facade
Socket
Socket with two 11.5 mm bore holes for securing insertion rails to building facades. Delivered with two facade anchors and corresponding screws.
Available in bare aluminium and black anodised variants.
90
Art.-No.
Designation
a in mm
251163
Socket 40 × 60 × 250 hole 2 × 11,5 complete
250
251164
Socket facade 40 × 60 × 250 complete sw
250
b in mm
c in mm
Material
60
200
Alu
60
200
Alu
Facade
b
Adapter plate
a
Adapter plate for securing the modules against slipping and for fastening perforated sheets. Preassembled with two 5 mm boreholes for connection to the socket,
as well as 4 drill screws with AW drive and two countersunk washers. Available in bare metal and black anodised variants.
Art.-No.
Designation
a in mm
b in mm
c in mm
Material
251000
Adapter plate 80 × 20 × 8 with accessories
80
20
Alu / V2A
251005
Adapter plate 80 × 20 × 8 black with accessories
80
20
Alu / V2A
Adapter plate
Adapter plate for side attachment of perforated sheets and as edge stop for the modules. Prefabricated with a 7 mm bore hole for a countersunk screw with AW drive.
Art.-No.
Designation
a in mm
b in mm
251001
Adapter plate 96 × 20 × 3 with accessories
96
20
c in mm
Material
Alu / V2A
Perforated sheet
Perforated sheet helps seal the gap between the facade and the photovoltaic system. Enables rear ventilation and does not hinder fire extinguishing in an emergency.
Available in bare aluminium and black anodised variants.
Art.-No.
Designation
a in mm
b in mm
251107
Perforated sheet 1500 × 120 ALU, bend 125°
83
38
c in mm
Gav. steel
Material
251108
Perforated sheet 1500 × 120 ALU, bend, black
83
38
Gav. steel
Connector plate perforated sheet
5
Connector plate for connecting two perforated sheets with each other. Suitable for both bare aluminium and black anodised perforated sheets. Pre-assembled with
two bore holes and drill screws with AW drive.
Designation
a in mm
b in mm
251264
Connector for perfor. sheet, accessories
65
20
c in mm
Material
Alu
91
INDIVIDUAL PRODUCTS
Art.-No.
novotegra components | Sealing parts and protective devices
1
2
3
4
5
6
7
8
ARTICLE NUMBER
DESIGNATION
210071
EPDM round seal d = 25 mm
1
210070
EPDM sealant strip for C-rail 50 × 35 mm
2
218084
Aluminium edge protector self-adhesive 250 × 50 mm
3
218060
Protective roof mat 10.000 × 250 × 6 mm
4
218065
Synthetic fibre strips 50000 × 320 mm
5
251039
EPDM tape (roll) 54 × 3 for ALUTEC, 10 m
6
251045
EPDM pieces (roll) 70 × 28 × 2
7
251040
EPDM edge protection 7 mm laminate, L 40
8
251041
EPDM edge protection 7 mm laminate, L 80
8
92
IMAGE NUMBER
novotegra components | Cable fixing
1
2
3
4
5
ARTICLE NUMBER
DESIGNATION
213601
Cable clip d=10 mm
IMAGE NUMBER
213600
Self-locking cable tie
2
251095
Cable-tie clip for profile flange 1 – 3 mm
2
251096
Cable-tie clip for profile flange 3 – 6 mm
2
251097
Cable collector PA for ALUVER, 4 cables
3
213602
Base trough cable bracket
4
251091
Cable tie black 140 mm
5
251092
5
251093
5
251094
5
1
93
INDIVIDUAL PRODUCTS
5
novotegra components | Accessories and optional components
1
2
3
4
5
6
7
8
9
10
ARTICLE NUMBER
DESIGNATION
215417
Mounting Set C-Rail M8
1
215418
Plate 50 × 50 × 3 D8,5 Al
1
251083
Shim for roof hook HDPE blue, 2 mm
2
251084
Shim for roof hook HDPE grey, 5 mm
2
251146
Slot nut M8 A2, spring ball, L 30
3
251499
Slot nut ALU, spring ball, C-slot 8.5 × 11
3
251145
Slot bolt, locking nut with flange
4
251101
L adapter set, fixing ALUVER to C-hook
5
251081
Mounting set snowguard pipe, woth screws
6
251013
Metal sheet zinc-plated, for plain tile
7
251551
Metal shingle 280 × 230 mm, with sealing
8
251552
8
251553
8
21700
Grounding connector set AF 18
9
251076
Base plate for stock screw M10, Al
10
251867
Base plate for stock screw M12, Al
10
94
IMAGE NUMBER
novotegra components | Tools
1
2
3
4
5
6
7
8
ARTICLE NUMBER
DESIGNATION
219192
Torx drive TX-40 length = 90 mm
IMAGE NUMBER
1
21905
Torx extension 250 mm
2
21900
Special long nut socket 18 mm
3
219001
Special nut socket 8 mm
4
219149
Threaded socket driver f. stock screw M10
5
21915
Threaded socket driver f. stock screw M12
5
219194
Drill bit 6.8 mm length 230 mm
6
219195
6
219196
6
219197
6
219200
7
219198
7
219201
Drill bit 14 mm HSS short
7
219199
Drill bit 16 mm HSS short
7
21920
Torque wrench 1/4", 4 – 20 Nm
8
95
INDIVIDUAL PRODUCTS
5
novotegra components | Tools
9
10
11
13
14
15
12
ARTICLE NUMBER
DESIGNATION
21921
Torque wrench 1/2", 20 – 100 Nm
9
218106
Mounting and removal tool 150 – 30
10
251501
Adapter 1/4" hexagonal to 1/2" square
11
251503
Bit for triple-square screws, size AW25
12
251504
12
251505
12
251572
Assembling jig 800 – 1200 mm, C-shaped
13
251570
Assembling jig 1300 – 1700 mm, C-shaped
13
251573
Assembling jig 800 – 1200 mm, bar type
13
251571
Assembling jig 1300 – 1700 mm, bar type
13
251575
Assembling jig set 800 – 1200 mm, 2-piece
13
251574
Assembling jig set 1300 – 1700 mm, 2-piece
13
251580
Tool trapez. sheet bracket / ALUTEC
14
251582
Tool trapez. sheet bracket / ALUTEC FL
14
251581
Tool trapez. sheet bracket / VARIOTECC
14
251511
Basic equipment
15
96
IMAGE NUMBER
T E R M S O F G UA R A N T E E
Product Guarantee for the novotegra Mounting System
from BayWa r.e. Solar Energy Systems GmbH
Terms of Guarantee
Under the following conditions, BayWa r.e. Solar Energy Systems GmbH guarantees that undernormal conditions of installation, application,
operation and maintenance the components of thenovotegra mounting system are free of construction, processing and material defects, for 10 years
from the date of receipt.
Only BayWa r.e. Solar Energy Systems GmbH may approve the warranty claim, and only through an independent test on-site. In the case of an approved warranty
claim the liability is effected solely through a replacement delivery of the defective component. An approved warranty claim does not lead to an extension
of the guarantee period, nor restart it. Subsequent to an accepted warranty claim, no further commitments and liabilities for additional and subsequent damages
for BayWa r.e. Solar Energy Systems GmbH exist. Thus a limitation of the legalwarranty claims and the legal product liability is not given.
Warranty Claim
In order to file a claim within 10 years, you must notify BayWa r.e. Solar Energy Systems GmbH in writing within two weeks of the detection of the fault and
supply the purchase date, the original order confirmation and delivery note from BayWa r.e. Solar Energy Systems GmbH as proof of purchase. The guarantor is
BayWa r.e. Solar Energy Systems GmbH, Eisenbahnstraße 150, 72072 Tübingen. The areas covered by this guarantee are based upon German law principles.
Furthermore, our general terms and conditions apply in addition to this guarantee.
Exclusions
Warranty claims under this guarantee cannot be made in the case of:
- Faulty or incorrect installation according to the installation instructions
- Unauthorised modifications or repairs
- Inappropriate installation or use of the mounting system.
- Inappropriate transportation, storage or handling of the components.
- Optical deficiencies in so far as the appearance does not have any influence on the performance of the component.
- Incorrect installation according to the static calculations, or installation instructions of other components ( for example, the solar module )
- Failure to comply with universally valid norms that have to be respected during installation
- Damage through e.g. smoke, exceptional thermal stress, salt loading or other chemical products.
- Forces of nature (natural hazard), force majeure, vandalism, destruction through external influences and / or persons / animals.
The cost to BayWa r.e. Solar Energy Systems GmbH for the removal and return of the defective component
as well as for the re-assembly of the delivered component are excluded from this guarantee.
97
C O N TAC T
Synonymous
with your success
Are you looking for a mounting system with low load reserve
or want to know which module can be best combined with a certain inverter?
We are happy to help you with the design of your photovoltaic system and support you
with any technical enquiries. Find the right contact person here:
CONTACT
Eisenbahnstrasse 150, 72072 Tübingen, Germany
Phone: +49 7071 98987 0
[email protected]
Sales office Brunswick
Heinrich-Büssing-Ring 25, 38102 Brunswick, Germany
Phone: +49 531 12177 100
[email protected]
Sales office Tübingen
Welzenwiler Strasse 5, 72074 Tübingen, Germany
Phone: +49 7071 98987 300
[email protected]
Sales office Munich
Beethovenplatz 4, 80336 Munich, Germany
Phone: +49 89 386670 0
[email protected]
Sales office Duisburg
Aakerfährstrasse 40, 47058 Duisburg, Germany
Phone: +49 203 298776 0
[email protected]
BayWa r.e. solar systemer ApS
Kullinggade 31E, 5700 Svendborg, Denmark
Phone: +45 62 21 10 00
[email protected]
Sales office Nuremberg
Wiesentalstrasse 32–34, 90419 Nuremberg, Germany
Phone: +49 911 216646 0
[email protected]
For information on our international offices, please visit
www.baywa-re.com and then click on “Locations”.
Imprint
BayWa r.e. renewable energy GmbH
Herzog-Heinrich-Strasse 9 | 80336 Munich, Germany | Phone: +49 89 38 39 32-0 | [email protected] | www.baywa-re.com
Concept and text BayWa r.e. Solar Energy Systems GmbH, Tübingen, Germany
Design concept Strichpunkt GmbH, Stuttgart | Berlin, Germany
Graphic mds. Agenturgruppe GmbH, Germany
Photos Ben Wiesenfarth, Konstanz; Reiner Pfisterer, Ludwigsburg, Germany
Reproduction mds. Agenturgruppe GmbH, Germany
Print Bosch-Druck GmbH, Ergolding, Germany, Version CA-094.01
Copyright May 2016 BayWa r.e. renewable energy GmbH, Munich. Errors and omissions excepted. Any reproduction, either in
whole or in part, requires the prior written consent of BayWa r.e. renewable energy GmbH.
98
Remain Flexible with
a Strong Network
BAYWA R.E. RENEWABLE ENERGY:
R.E.SPONSIBLE FOR YOUR SUCCESS.
BayWa r.e.was founded as a fully owned subsidiary of BayWa AG in 2009.
The company combines all of the Group’s activities in the field of renewable energies:
photovoltaic, wind, biomass and geothermal energy. Today, BayWa r.e. is one of the
world’s most stable project developers and system providers of PV plants.
The company is currently active in Germany, numerous European countries, the US and Asia.
BayWa r.e.’s goal is to promote the expansion of renewable energies worldwide.
Thanks to the size, global network and financial strength of BayWa AG,
we are optimally prepared to fulfil this mission.
BAYWA AG: ACTING FOR THE FUTURE
BayWa is a group with worldwide operations in the core competencies of trading, logistics
and services in the segments of Agriculture, Energy, and Building Materials.
The head office of the parent company, which was founded in 1923, is located in Munich.
The international activities focus on Europe as well as on the US and New Zealand.
The company is SDAX listed.
BayWa’s goal is to shape the future of human needs in an innovative and lasting manner
based on trust in its role as a strong partner.
Eisenbahnstrasse 150
72072 Tübingen, Germany
Phone +49 7071 98987-0
Fax
+49 7071 98987-10
[email protected]
www.baywa-re.com
solarenergysystems.baywa-re.com

Mounting Systems

Transcription

Similar documents

Untitled - Tin Roof

Atlantis Energy

Quick Guide

New 2010 UG Brochure.cdr

TCX625HD Heavy-Duty Tire Changer

KITCHEN FAUCETS

LRM2 pdf - published November 2010

polystick tu plus

Urban Ecosystem Recovery with Green Technology y y gy y y gy

ECO 01-1.psd