PROPANE CONSTRUCTION CONVECTION HEATER

TM
PROPANE CONSTRUCTION
CONVECTION HEATER
OWNER’S MANUAL
For more information, visit www.desatech.com
Variable
100,000, 150,000, and
200,000 Btu/Hr Models
AT
PUSH
TO START
LO
HI
IMPORTANT: Read and understand this manual before assembling, starting, or servicing
heater. Improper use of heater can cause serious injury. Keep this manual for future reference.
GENERAL HAZARD WARNING: FAILURE TO COMPLY WITH THE PRECAUTIONS AND
INSTRUCTIONS PROVIDED WITH THIS HEATER, CAN RESULT IN DEATH, SERIOUS BODILY
INJURY AND PROPERTY LOSS OR DAMAGE FROM HAZARDS OF FIRE, EXPLOSION, BURN,
ASPHYXIATION, CARBON MONOXIDE POISONING AND/OR ELECTRICAL SHOCK.
ONLY PERSONS WHO CAN UNDERSTAND AND FOLLOW THE INSTRUCTIONS SHOULD USE
OR SERVICE THIS HEATER.
IF YOU NEED ASSISTANCE OR HEATER INFORMATION SUCH AS AN INSTRUCTIONS
MANUAL, LABELS, ETC. CONTACT THE MANUFACTURER.
TABLE OF CONTENTS
SAFETY INFORMATION ............................................................ 2
MAINTENANCE .......................................................................... 5
PRODUCT IDENTIFICATION ..................................................... 3
SPECIFICATIONS ...................................................................... 6
UNPACKING ............................................................................... 3
REPLACEMENT PARTS ............................................................ 6
THEORY OF OPERATION ......................................................... 3
ACCESSORIES .......................................................................... 6
PROPANE SUPPLY .................................................................... 3
TROUBLESHOOTING ................................................................ 7
INSTALLATION ........................................................................... 4
ILLUSTRATED PARTS BREAKDOWN AND PARTS LIST ......... 8
VENTILATION ............................................................................. 4
OWNER’S REGISTRATION FORM ............................................ 9
OPERATION ............................................................................... 4
WARRANTY INFORMATION ...................................... Back Cover
STORAGE ................................................................................... 5
Save this manual for future reference.
2
SAFETY INFORMATION
SAFETY INFORMATION
WARNINGS
WARNING: This product contains and/or generates
chemicals known to the State of California to cause
cancer or birth defects, or other reproductive harm.
WARNING: FIRE, BURN, INHALATION, AND EXPLOSION HAZARD. KEEP SOLID COMBUSTIBLES,
SUCH AS BUILDING MATERIALS, PAPER OR CARDBOARD, A SAFE DISTANCE AWAY FROM THE
HEATER AS RECOMMENDED BY THE INSTRUCTIONS. NEVER USE THE HEATER IN SPACES WHICH
DO OR MAY CONTAIN VOLATILE OR AIRBORNE
COMBUSTIBLES, OR PRODUCTS SUCH AS GASOLINE, SOLVENTS, PAINT THINNER, DUST PARTICLES
OR UNKNOWN CHEMICALS.
WARNING: NOT FOR HOME OR RECREATIONAL
VEHICLE USE.
The heater is designed for use as a construction heater in accordance
with ANSI Z83.7/CGA 2.14. Other standards govern the use of fuel
gases and heating products for specific uses. Your local authority can
advise you about these. The primary purpose of construction heaters is
to provide temporary heating of buildings under construction, alteration
or repair. Properly used, the heater provides safe economical heating.
Products of combustion are vented into the area being heated.
We cannot foresee every use which may be made of our heaters.
CHECK WITH YOUR LOCAL FIRE SAFETY AUTHORITY
IF YOU HAVE QUESTIONS ABOUT HEATER USE.
Other standards govern the use of fuel gases and heat producing
products for specific uses. Your local authorities can advise you
about these.
Carbon Monoxide Poisoning: Some people are more affected by
carbon monoxide than others. Early signs of carbon monoxide poisoning resemble the flu, with headaches, dizziness, and/or nausea. If you
have these signs, the heater may not be working properly. Get fresh air
at once! Check for proper ventilation and have heater serviced.
Propane Gas: Propane gas is odorless. An odor-making agent is
added to propane gas. The odor helps you detect a propane gas leak.
However, the odor added to propane gas may fade. Propane gas may
be present even though no odor exists.
Make certain you read and understand all warnings. Keep this
manual for reference. It is your guide to safe and proper operation
of this heater.
• Install and use heater with care. Follow all local ordinances and
codes. In the absence of local ordinances and codes, refer to the
Standard for Storage and Handling of Liquefied Petroleum Gas,
ANSI/NFPA 58 and the Natural Gas Installation Code, CAN/
CGA B149.2. This instructs on the safe storage and handling of
propane gases.
• This product has been approved for use in the Commonwealth
of Massachusetts.
• Use only propane gas set up for vapor withdrawal.
• Provide adequate ventilation. Before using heater, provide at least
a six-square-foot opening of fresh, outside air. This heater produces carbon monoxide, which is listed by the State of California as a reproductive toxin under Proposition 65.
• For indoor use only. Do not use heater outdoors.
• Keep heater away from strong drafts, wind, water spray, rain, or
dripping water.
• Do not use heater in occupied dwellings or in living or sleeping
quarters.
• Do not use heater in a basement or below ground level. Propane
gas is heavier than air. If a leak occurs, propane gas may sink to
the lowest possible level.
• Keep appliance area clear and free from combustible materials, gasoline, paint thinner, and other flammable vapors and liquids. Dust is
combustible. Do not use heater in areas with high dust content.
• Minimum heater clearances from combustibles:
Sides: 3 feet, Top: 7 feet.
• Keep heater at least six feet from propane tank(s).
• Keep propane tank(s) below 100° F.
• Check heater for damage before each use. Do not use a damaged heater.
• Use only the hose and factory preset regulator provided with the
heater.
• Check hose before each use of heater. If highly worn or cut,
replace with hose specified by manufacturer before using heater.
• Do not alter heater. Keep heater in its original state.
• Do not use heater if altered.
• Locate heater on stable and level surface if heater is hot or
operating.
• Not intended for use on finished floors.
• Never block air inlet (bottom of shell) or air outlet (around top
of shell) of heater.
• Do not leave heater unattended.
• Keep children and animals away from heater.
• Never move, handle, or service a hot or operating heater. Severe
burns may result. Wait 15 minutes after turning heater off.
For more information, visit www.desatech.com
103386-01G
SAFETY INFORMATION
PRODUCT IDENTIFICATION
UNPACKING
THEORY OF OPERATION
PROPANE SUPPLY
SAFETY INFORMATION
UNPACKING
Continued
1.
•
•
•
•
2.
3.
To prevent injury, wear gloves when handling heater.
Never attach duct work to heater.
Turn off propane supply to heater when not in use.
Use only original replacement parts. This heater must use design-specific parts. Do not substitute or use generic parts. Improper replacement parts could cause serious or fatal injuries.
PRODUCT IDENTIFICATION
Top
3
3
Remove all packing items applied to heater for shipment. Keep
plastic cover caps (attached to valve inlet and hose/regulator
assembly) for storage.
Remove all items from carton.
Check all items for shipping damage. If heater is damaged,
promptly inform dealer where you bought heater.
THEORY OF OPERATION
The Fuel System: The hose/regulator assembly attaches to the
propane gas supply. This provides fuel to the heater.
The Ignition System: The piezo ignitor lights the burner fuel supply.
The Automatic Control System: The automatic control valve shuts
off the heater if the flame goes out.
PROPANE SUPPLY
Shell
Use this heater only with a propane vapor withdrawal supply
system. See Chapter 5 of the Standard for Storage and Handling of
Liquefied Petroleum Gas, ANSI/NFPA 58 and/or CAN/CGA B149.2.
Your local library or fire department will have this booklet.
Ignitor
Electrode
Thermocouple
Piezo
Ignitor
Button
Hose/
Regulator
Assembly
You must provide propane gas and tank(s).
Base
The amount of propane gas ready for use from propane tanks varies.
Two factors decide this amount.
1. The amount of liquid propane gas in tank(s)
2. The temperature of tank(s)
The chart below shows the minimum number of 100-pound tanks
needed to run the heater. Connect tanks together with a manifold. Do
not operate this product with any tank smaller than 100 pounds.
AT
PUSH
TO START
LO
HI
Valve Inlet
Figure 1 - Product Identification
Control Knob
Average Temp. (°F)
At Tank Location
60°
40°
32°
20°
10°
0°
Number Of
Tanks
2
2
2
2
3
3
Less gas is vaporized at lower temperatures. Two or more 100-pound
tanks or one larger tank may be needed in colder weather. Your local
propane gas dealer will help you select the proper supply system.
For more information, visit www.desatech.com
103386-01G
4
VENTILATION
INSTALLATION
OPERATION
To Start Heater
VENTILATION
WARNING: Provide at least a 6 square foot opening of fresh, outside air while running heater. If proper
fresh, outside air ventilation is not provided, carbon
monoxide poisoning can occur. Provide proper fresh,
outside air ventilation before running heater.
Propane
Supply Valve
Fuel Gas
Fitting
Hose
Regulator
Vent
(pointing down)
FRESH OUTSIDE AIR OPENING REQUIREMENTS
HEATER SIZE
200,000 Btu/Hr
SQ. FT. OPENING
6.0
INSTALLATION
Propane Tank
Figure 2 - Regulator With Vent Pointing Down
WARNING: Review and understand the warnings
in the Safety Information section, pages 2 and 3. They
are needed to safely operate this heater. Follow all
local codes when using this heater.
Valve Inlet
AT
PUSH
TO START
LO
HI
Hose
WARNING: Test all gas piping and connections
for leaks after installation or servicing. Never use an
open flame to check for a leak. Apply a mixture of
liquid soap and water to all joints. Bubbles forming
show a leak. Correct all leaks at once.
1.
2.
3.
4.
5.
6.
Provide propane supply system (see Propane Supply, page 3).
Connect fuel gas fitting on hose/regulator assembly to propane tank(s). Turn fuel gas fitting counterclockwise into threads
on tank. Tighten firmly using a wrench. IMPORTANT: Tighten
regulator with vent pointing down. Pointing vent down protects regulator from weather damage.
Connect hose to the valve inlet. Tighten firmly using a wrench.
You must use the regulator supplied with heater even if propane tank has one.
Open propane supply valve on propane tank(s) slowly. Note:
If not opened slowly, excess-flow check valve on propane tank
may stop gas flow. If this happens, you may hear a click inside
the regulator assembly, this is the check valve closing. To reset the excess-flow check valve, close propane supply valve
and open it again slowly.
Check all connections for leaks. Apply mixture of liquid soap
and water to gas joints. Bubbles forming show a leak that must
be corrected.
Close propane supply valve.
Figure 3 - Hose and Valve Inlet
OPERATION
WARNING: Review and understand the warnings
in the Safety Information section on pages 2 and 3.
They are needed to safely operate this heater. Follow
all local codes when using this heater.
TO START HEATER
1.
2.
3.
4.
5.
Follow all installation, ventilation, and safety information.
Locate heater on stable and level surface. Make sure strong
drafts do not blow on heater.
Open propane supply valve on propane tank(s) slowly. Note:
If not opened slowly, excess-flow check valve on propane tank
may stop gas flow. If this happens, you may hear a click inside
the regulator assembly, this is the check valve closing. To reset the excess-flow check valve, close propane supply valve
and open it again slowly.
Turn control knob clockwise to the lowest position and push
in (see Figure 4, page 5).
With the control knob pushed all the way in, press and release
the piezo ignitor button (see Figure 4, page 5). Keep pressing
piezo ignitor button until the burner lights. Hold control knob
down for a maximum of 10 seconds while attempting ignition.
If heater does not ignite, release control knob and wait 3 minutes before attempting reignition.
Note: Keep hands and face away from outlet (around top of shell)
of heater while attempting to start heater.
For more information, visit www.desatech.com
103386-01G
OPERATION
To Start Heater (Cont.)
To Stop Heater
To Restart Heater
5
5
STORAGE
MAINTENANCE
OPERATION
STORAGE
Continued
6.
7.
After ignition, hold control knob down for about 30 seconds.
This activates the automatic control system.
When burner remains lit, set heater at the desired heat level by
turning the control valve counterclockwise. If burner goes out,
turn off gas. Turn control knob fully clockwise to the lowest
position. Check fuel supply. If adequate fuel is available, restart heater beginning at step #1.
CAUTION: Do not operate heater at extremely low
input gas pressures (100% yellow flame). This may
cause sooting inside heater.
CAUTION: Disconnect heater from propane supply tank(s).
1.
2.
3.
MAINTENANCE
Control Knob
Piezo
Ignitor
Button
WARNING: Never attempt to service heater while
it is connected to propane supply, operating, or hot.
Severe burns can occur.
AT
PUSH
TO START
LO
HI
1.
2.
AT
PUSH
TO START
LO
HI
3.
Figure 4 - Control Knob, and Piezo Ignitor Button Locations
Store propane tank(s) in safe manner. Refer to Chapter 5 of
Standard for Storage and Handling of Liquefied Petroleum
Gases, ANSI/NFPA 58 and/or CAN/CGA B149.2. Follow all
local codes. Always store propane tanks outdoors.
Place plastic cover caps over brass fittings on valve inlet and
hose/regulator assembly.
Store in a dry, clean, and safe place.
4.
Keep heater clean.
Inspect heater before each use. Check connections for leaks.
Apply mixture of liquid soap and water to connections. Bubbles
forming show a leak that must be corrected. Correct all leaks
at once.
Inspect hose/regulator assembly before each use. If hose is highly
worn or cut, replace with hose specified by manufacturer.
Have heater inspected yearly by a qualified service person.
TO STOP HEATER
1.
2.
Tightly close propane supply valve on propane tank(s). Allow
heater to burn remaining fuel in hose.
Shut off main burner valve. Do this by turning control knob
fully clockwise. Make sure you turn the knob until it stops.
TO RESTART HEATER
1.
2.
Wait five minutes after stopping heater.
Restart heater by following steps under To Start Heater, page 4.
For more information, visit www.desatech.com
103386-01G
6
SPECIFICATIONS
REPLACEMENT PARTS
ACCESSORIES
SPECIFICATIONS
ACCESSORIES
Rating (BTU/Hr) ............. High - 200,000
Medium - 150,000
Low - 100,000
Purchase these accessories and parts from your local dealer or
service center. If your dealer or service center can not supply an
accessory or part, contact your nearest Parts Central (listed in the
separate Authorized Service Center booklet) or call DESA International at 1-866-672-6040 for referral information. You can also
write to the address listed on the back page of this manual.
Fuel Propane Vapor Only
Fuel Consumption ........... Gallons/Hour - 1.09 min./2.19 max.
Pounds/Hour - 4.64 min./9.28 max.
Supply Pressure To Regulator
Maximum ............... 200 psi
Minimum ................ 20 psi (for input adjustment)
Part Number
LPA1020
Manifold Pressure ............ High 4.6 psi, Low 5.9 psi
LPA2005
Minimum Temp. .............. -20°F (-29°C) Surrounding Air
Weight (pounds)
Heater ..................... 16
Shipping .................. 21
LPA3005
LPA4020
Size - L x W x H (inches)
Heater ..................... 15 x 16 x 30
Shipping .................. 18 x 18.6 x 31.25
Description
10' Rubber Hose with Brass Fitting
U.L. listed.
Propane Gas Regulator
U.L. listed.
Hose/Regulator Assembly
U.L. listed.
Fuel Gas Connector
Connects regulator to all standard
propane tanks. U.L. and A.G.A. listed.
REPLACEMENT PARTS
WARNING: Use only original replacement parts.
This heater must use design-specific parts. Do not
substitute or use generic parts. Improper replacement parts could cause serious or fatal injuries. This
will also protect your warranty coverage for parts
replaced under warranty.
PARTS UNDER WARRANTY
Contact authorized dealers of this product. If they can’t supply
original replacement part(s), either contact your nearest Parts Central or call DESA International’s Technical Service Department at
1-866-672-6040. When calling DESA International, have ready
• your name
• how heater was malfunctioning
• your address
• purchase date
• model and serial numbers of your heater
In most cases, we will ask you to return the part to the factory.
PARTS NOT UNDER WARRANTY
Contact authorized dealers of this product. If they can’t supply
original replacement part(s), either contact your nearest Parts Central or call DESA International at 1-866-672-6040 for information.
When calling DESA International, have ready
• model number of your heater
• the replacement part number
For more information, visit www.desatech.com
103386-01G
TROUBLESHOOTING
TROUBLESHOOTING
Note: For additional help, visit DESA
International’s technical service website at
www.desatech.com.
WARNING: Never attempt to service heater while
it is connected to propane supply, operating, or hot.
Severe burns can occur.
SYMPTOM
POSSIBLE CAUSE
REMEDY
Burner fails to light
1. Propane supply valve closed on propane
tank(s)
2. Excess-flow check valve closed
1. Open propane supply valve slowly
3. Blockage in burner nozzle
4. Piezo ignition system not sparking
Burner lights but goes out when automatic control valve button is released
1. Not enough warm-up time
2. Low gas pressure
3. Thermocouple loose or needs to be replaced
4. Automatic control valve needs to be replaced
1. Main burner valve not fully open
Burn rate is low
2. Plugged gas orifices
3. Low gas pressure
4. Low fuel supply
2. Close propane supply valve on propane tank
and reopen slowly
3. Replace burner nozzle
4. Check to assure ignitor electrode gap is
.130". Check wire lead for damage. Replace
piezo ignitor and/or ignitor electrode as necessary
1. Relight, hold automatic control valve button in 45 seconds
2. Check propane tank(s) for proper gas supply
3. Tighten connection or replace thermocouple
4. Replace automatic control valve
1. Fully open main burner valve by turning
control knob towards HIGH position until
it stops
2. Replace gas orifice
3. Check gas supply; check regulator output
4. Consult propane gas supplier
For more information, visit www.desatech.com
103386-01G
7
7
8
ILLUSTRATED PARTS BREAKDOWN AND PARTS LIST
Models TC200V and RCP200V
ILLUSTRATED PARTS
BREAKDOWN AND PARTS LIST
MODELS
TC200V
RCP200V
This list contains replaceable parts used in your heater. When ordering
parts, follow the instructions listed under Replacement Parts on page 5
of this manual.
1
KEY
NO.
PART
NO.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
103925-01
103923-01
101263-01
097162-02
103031-02
103924-01
102445-01
**
103906-01
103927-01
103926-01
103398-01
103396-01
Top and Shell Assembly
Burner Ring Assembly
Burner Plate
Burner Nozzle
Base
Knob Assembly
Piezo Ignitor
Thermocouple Kit
Thermocouple Bracket
Fuel Tube Kit
Valve Assembly
Ignitor Electrode
Heat Shield
QTY.
1
1
1
1
1
1
1
1
1
1
1
1
1
PARTS AVAILABLE - NOT SHOWN
098853-07
098851-06
098831-05
101284-02
Tradename Decal (TC200V)
Tradename Decal (RCP200V)
Information Decal
Operation Decal
4
3
2
12
1
1
1
1
9
8
** Not a field replaceable part.
10
5
7
11
AT
PUSH
TO START
LO
6
HI
13
For more information, visit www.desatech.com
103386-01G
9
9
OWNER'S REGISTRATION FORM
Complete registration form and mail or complete on-line registration at www.desatech.com within 30 days after purchase.
Brand:
(Reddy Heater, Master, Remington, etc.)
Model:
(R60, HD15, etc.)
Date Purchased:
Note: Keep receipt for warranty verification.
Serial Number:
7 or 9 digit number located on product or identification tag.
First Name:
Last Name:
Address:
City:
Phone: (
State:
)
-
Zip:
Country:
E-Mail:
Please answer the following questions to register your product with DESA International:
❍ Individual
❍ Business
1.
Who will heater be used by?
2.
Will you use your heater in more than one location? ❍ Yes
3.
Where will the product be used? (You may select more than one.) ❍ Workshop ❍ Barn ❍ Residential Construction
❍ No
❍ Commercial Construction ❍ Garage ❍ Factory ❍ Recreation
❍ Warehouse
❍ Utility Shed/Outbuilding
❍ Other ______________________________ (Specify)
4.
Cost of product (excluding sales tax)? $________________________________
5.
Maintenance/service work will be performed by: ❍ Self
6.
If you bought this product yourself, did you plan to purchase this type of product before going into the store?
❍ Service Center
7. Type of store where product was purchased? ❍ Hardware
❍ Farm/Ag. Supply
❍ Discount Store
❍ Other ___________________________________
❍ Propane Dealer
❍ Natural Gas/Utility Co.
❍ Auto Parts ❍ Warehouse Club ❍ Industrial/Contractor Supply
❍ HVAC Dealer
❍ Yes ❍ No
❍ Home Center or Builder's Supply
❍ Rental Store
❍ Other _________________________________________________
❍ Propane (LP Gas)
❍ Natural Gas
❍ Kerosene ❍ Diesel
❍ Electric
❍ Other________________
8.
What is your primary source of heat?
9.
What motivated you to buy this product? ❍ Sudden Cold Weather ❍ Replace Older Model ❍ D.I.Y. Home Project ❍ Emergency Back-Up Heat
❍ Heater on Sale ❍ Construction Project ❍ Hard to Heat Location
10. How did you learn about this product brand? ❍ Advertisement
❍ Store Display
❍ Previously Owned a Heater
❍ Other ________________________________
❍ Relative or Friend
❍ Co-Worker
❍ Store Representative
❍ Other _________________________________________________(Specify)
11. What other brands did you consider? ❍ None ❍ Master ❍ Remington ❍ All-Pro ❍ Dayton ❍ Universal ❍ Mr. Heater ❍ L.B. White Tradesman
❍ John Deere ❍ Dyna-Glo ❍ Dura-Heat ❍ Paulin ❍ Coleman ❍ Vogelzang American ❍ Other ___________________________________
12. Who selected the product? ❍ Male ❍ Female ❍ Both
13. Level of Education of Purchaser: ❍ High School
14. Age of Purchaser: ❍ Under 20
❍ 20 - 29
❍ Vocation/Technical School
❍ 30 - 39
❍ 40 - 49
15. Buyer's total annual household income: ❍ Under $19,999
❍ $50,000 to $74,999
❍ $75,000 to $99,999
❍ Completed College
❍ Graduate School
❍ 60 or Over
❍ $20,000 to $34,999
❍ $35,000 to $49,999
❍ $100,000 and Over
16. What is the population of your area? ❍ Under 10,000
❍ 100,000 to 250,000
❍ 50 - 59
❍ Some College
❍ 10,000 to 25,000
❍ 25,000 to 50,000
❍ 50,000 to 100,000
❍ Over 250,000
17. Store where product was purchased:
Name: ______________________________________ City: _____________________________________ State: __________
18. In choosing this product, how important were the following:
Not Somewhat
Very
❍
❍
❍
Availability
❍
❍
❍
Price
❍
❍
❍
Brand Name
❍
❍
❍
Overall Quality
❍
❍
❍
Heat Output (Btu/Hr Rating)
❍
❍
❍
Variable Heat Output (Btu/Hr)
❍
❍
❍
Made in USA
❍
❍
❍
Warranty
❍
❍
❍
Local Service
❍
❍
❍
Value for Price
Size
Prior Brand Experience
Built-In Thermostat
Ease of Operation
Special Features
Salesperson's Recommendation
Friend/Relative's Recommendation
Portability
Quiet Operation
Not
❍
❍
❍
❍
❍
❍
❍
❍
❍
Somewhat
❍
❍
❍
❍
❍
❍
❍
❍
❍
Very
❍
❍
❍
❍
❍
❍
❍
❍
❍
19. This question will allow us to better understand the demographic profile of our customers. Which of the following best describes you? (not required)
For more information, visit www.desatech.com
❍ African American ❍ Asian American ❍ Mexican ❍ Puerto Rican ❍ Cuban ❍ Other Hispanic ❍ White ❍ Other ___________________
103386-01G
TAPE
Postage
Required
TM
2701 Industrial Drive
P.O. Box 90004
Bowling Green, KY 42102-9004
TAPE
W
AR
NIN
G
klsu
;e iejlb
;;pd oek
l;lkl lhi
suie kok
jlb le ,,;lo
oek
g;e
lhi
kok ;;pd
l;lkl
le
,,;lo suie
klsu
g;e
;l klsuiejlb
jlb
;;pd oe
klsu iejlboek
lhi
l;l
klsu iejlb
oek kok
le
klsu iejlb oek lhi
kok ,,;lo
lhi
klsu iejlb oek
g;e
lhi kokle le ,,;lo
klsu iejlb oek
kok
,,;lo g;e ;;pd
l;l
iejlb oek lhi kok le
,,;lo g;e
;;pd klsu
oek lhi kok le
,,;lo g;e ;;pd l;l klsuiejlb
lhi
kok le ,,;lo g;e ;;pd l;l klsu iejlboek
l;l
lhi
le
klsu iejlb
,,;lo g;e ;;pd
oek kok
g;e ;;pd l;l klsu iejlb oek lhi
le
,,;lo
;;pd l;l
iejlb oek lhi kokkok
g;e
le
l;l
,,;lo
oek lhi kok le
klsu
,,;lo g;e ;;pd
lhi
l
iejlb
kok le ,,;lo g;e
;;pd
oek
le
,,;lo g;e ;;pd l;l
lhi
g;e ;;pd l;l
kok
le
;;pd l;l
,,;lo
l;l
g;e
;;pd
l;l
WARNING
klsuiejlb oeklhi
kokle ,,;log;e
;l klsuiejlb
;;pdl;l klsuiejlb
oeklhi
klsuiejlb oeklhi kokle ,,;log;e
oeklhi kokle
;;pdl;l
,,;log;e ;;pdl
klsuiejlb oeklhikokle ,,;log;e ;;pdl;l klsuiejlb oeklhi
kokle
klsuiejlb oeklhikokle ,,;log;e ;;pdl;lklsuiejlb oeklhi kokle ,,;log;e ;;pdl;l
klsuiejlb oeklhikokle ,,;log;e ;;pdl;lklsuiejlb oeklhi kokle,,;log;e ;;pdl;l
klsuiejlb oeklhikokle ,,;log;e ;;pdl;lklsuiejlb oeklhi kokle,,;log;e ;;pdl;l
,,;log;e ;;pdl;l
kokle ,,;log;e
;;pdl;l klsuiejlb
oeklhi kokle
,,;log;e ;;pdl;l
klsuiejlb
oeklhi kokle
,,;log;e
;e ;;pdl;lklsuie
jlb oeklhi ;;pdl;lklsuiejlb oeklhi
kokle ,,;log;e
;;pdl;l
OTHER OUTDOOR HEATING PRODUCTS
PROPANE/LP FORCED AIR HEATERS
PROPANE/LP CONVECTION HEATERS
PORTABLE KEROSENE/DIESEL
FORCED AIR HEATERS
PROPANE/LP TANK TOP HEATERS
PROPANE/LP AND NATURAL
GAS GARAGE HEATERS
PROPANE/LP
PATIO HEATERS
PROPANE/LP AND NATURAL
GAS CHIMENEAS
12
WARRANTY AND REPAIR SERVICE
KEEP THIS WARRANTY
LIMITED WARRANTY
DESA International warrants this product and any parts thereof, to be free from defects in materials and workmanship for one (1) year from the date
of first purchase when operated and maintained in accordance with instructions. This warranty is extended only to the original retail purchaser, when
proof of purchase is provided.
This warranty covers only the cost of parts and labor required to restore the product to proper operating condition. Transportation and incidental costs
associated with warranty repairs are not reimbursable under this warranty.
Warranty service is available only through authorized dealers and service centers.
This warranty does not cover defects resulting from misuse, abuse, negligence, accidents, lack of proper maintenance, normal wear, alteration,
modification, tampering, contaminated fuels, repair using improper parts, or repair by anyone other than an authorized dealer or service center. Routine
maintenance is the responsibility of the owner.
THIS EXPRESS WARRANTY IS GIVEN IN LIEU OF ANY OTHER WARRANTY EITHER EXPRESSED OR IMPLIED, INCLUDING
WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
DESA International assumes no responsibility for indirect, incidental or consequential damages. Some states do not allow the exclusion or limitation
of incidental or consequential damages, or limitations or exclusions may not apply to you. This Limited Warranty gives you specific legal rights and
you may also have other rights which vary from state to state.
This warranty does not cover discoloration due to operation of heater. We reserve the right to amend these specifications at any time without notice.
The only warranty applicable is our standard written warranty. We make no other warranty, expressed or implied.
WARRANTY SERVICE
Should your heater require service, return it to your nearest authorized service center. Proof of purchase must be presented with the heater. The heater
will be inspected. A defect may be caused by faulty materials or workmanship. If so, DESA International will repair or replace the heater without charge.
REPAIR SERVICE
Return your heater to your nearest authorized service center. Repairs not covered by the warranty will be billed at standard prices. Each Service Center
is independently owned and operated. We reserve the right to amend these specifications at any time without notice.
For information, write: DESA International, P.O. Box 90004
Bowling Green, Kentucky 42102-9004 ATTN: Customer Service Department
When writing, always include model number and serial number.
Model
TM
Serial No.
2701 Industrial Drive
P.O. Box 90004
Bowling Green, KY 42102-9004
Date of Purchase
103386 01
NOT A UPC
103386-01
Rev. G
11/02
For more information, visit www.desatech.com
103386-01G